1 // SPDX-License-Identifier: GPL-2.0 2 /* 3 * xHCI host controller driver 4 * 5 * Copyright (C) 2008 Intel Corp. 6 * 7 * Author: Sarah Sharp 8 * Some code borrowed from the Linux EHCI driver. 9 */ 10 11 12 #include <linux/slab.h> 13 #include <asm/unaligned.h> 14 #include <linux/bitfield.h> 15 16 #include "xhci.h" 17 #include "xhci-trace.h" 18 19 #define PORT_WAKE_BITS (PORT_WKOC_E | PORT_WKDISC_E | PORT_WKCONN_E) 20 #define PORT_RWC_BITS (PORT_CSC | PORT_PEC | PORT_WRC | PORT_OCC | \ 21 PORT_RC | PORT_PLC | PORT_PE) 22 23 /* Default sublink speed attribute of each lane */ 24 static u32 ssp_cap_default_ssa[] = { 25 0x00050034, /* USB 3.0 SS Gen1x1 id:4 symmetric rx 5Gbps */ 26 0x000500b4, /* USB 3.0 SS Gen1x1 id:4 symmetric tx 5Gbps */ 27 0x000a4035, /* USB 3.1 SSP Gen2x1 id:5 symmetric rx 10Gbps */ 28 0x000a40b5, /* USB 3.1 SSP Gen2x1 id:5 symmetric tx 10Gbps */ 29 0x00054036, /* USB 3.2 SSP Gen1x2 id:6 symmetric rx 5Gbps */ 30 0x000540b6, /* USB 3.2 SSP Gen1x2 id:6 symmetric tx 5Gbps */ 31 0x000a4037, /* USB 3.2 SSP Gen2x2 id:7 symmetric rx 10Gbps */ 32 0x000a40b7, /* USB 3.2 SSP Gen2x2 id:7 symmetric tx 10Gbps */ 33 }; 34 35 static int xhci_create_usb3x_bos_desc(struct xhci_hcd *xhci, char *buf, 36 u16 wLength) 37 { 38 struct usb_bos_descriptor *bos; 39 struct usb_ss_cap_descriptor *ss_cap; 40 struct usb_ssp_cap_descriptor *ssp_cap; 41 struct xhci_port_cap *port_cap = NULL; 42 u16 bcdUSB; 43 u32 reg; 44 u32 min_rate = 0; 45 u8 min_ssid; 46 u8 ssac; 47 u8 ssic; 48 int offset; 49 int i; 50 51 /* BOS descriptor */ 52 bos = (struct usb_bos_descriptor *)buf; 53 bos->bLength = USB_DT_BOS_SIZE; 54 bos->bDescriptorType = USB_DT_BOS; 55 bos->wTotalLength = cpu_to_le16(USB_DT_BOS_SIZE + 56 USB_DT_USB_SS_CAP_SIZE); 57 bos->bNumDeviceCaps = 1; 58 59 /* Create the descriptor for port with the highest revision */ 60 for (i = 0; i < xhci->num_port_caps; i++) { 61 u8 major = xhci->port_caps[i].maj_rev; 62 u8 minor = xhci->port_caps[i].min_rev; 63 u16 rev = (major << 8) | minor; 64 65 if (i == 0 || bcdUSB < rev) { 66 bcdUSB = rev; 67 port_cap = &xhci->port_caps[i]; 68 } 69 } 70 71 if (bcdUSB >= 0x0310) { 72 if (port_cap->psi_count) { 73 u8 num_sym_ssa = 0; 74 75 for (i = 0; i < port_cap->psi_count; i++) { 76 if ((port_cap->psi[i] & PLT_MASK) == PLT_SYM) 77 num_sym_ssa++; 78 } 79 80 ssac = port_cap->psi_count + num_sym_ssa - 1; 81 ssic = port_cap->psi_uid_count - 1; 82 } else { 83 if (bcdUSB >= 0x0320) 84 ssac = 7; 85 else 86 ssac = 3; 87 88 ssic = (ssac + 1) / 2 - 1; 89 } 90 91 bos->bNumDeviceCaps++; 92 bos->wTotalLength = cpu_to_le16(USB_DT_BOS_SIZE + 93 USB_DT_USB_SS_CAP_SIZE + 94 USB_DT_USB_SSP_CAP_SIZE(ssac)); 95 } 96 97 if (wLength < USB_DT_BOS_SIZE + USB_DT_USB_SS_CAP_SIZE) 98 return wLength; 99 100 /* SuperSpeed USB Device Capability */ 101 ss_cap = (struct usb_ss_cap_descriptor *)&buf[USB_DT_BOS_SIZE]; 102 ss_cap->bLength = USB_DT_USB_SS_CAP_SIZE; 103 ss_cap->bDescriptorType = USB_DT_DEVICE_CAPABILITY; 104 ss_cap->bDevCapabilityType = USB_SS_CAP_TYPE; 105 ss_cap->bmAttributes = 0; /* set later */ 106 ss_cap->wSpeedSupported = cpu_to_le16(USB_5GBPS_OPERATION); 107 ss_cap->bFunctionalitySupport = USB_LOW_SPEED_OPERATION; 108 ss_cap->bU1devExitLat = 0; /* set later */ 109 ss_cap->bU2DevExitLat = 0; /* set later */ 110 111 reg = readl(&xhci->cap_regs->hcc_params); 112 if (HCC_LTC(reg)) 113 ss_cap->bmAttributes |= USB_LTM_SUPPORT; 114 115 if ((xhci->quirks & XHCI_LPM_SUPPORT)) { 116 reg = readl(&xhci->cap_regs->hcs_params3); 117 ss_cap->bU1devExitLat = HCS_U1_LATENCY(reg); 118 ss_cap->bU2DevExitLat = cpu_to_le16(HCS_U2_LATENCY(reg)); 119 } 120 121 if (wLength < le16_to_cpu(bos->wTotalLength)) 122 return wLength; 123 124 if (bcdUSB < 0x0310) 125 return le16_to_cpu(bos->wTotalLength); 126 127 ssp_cap = (struct usb_ssp_cap_descriptor *)&buf[USB_DT_BOS_SIZE + 128 USB_DT_USB_SS_CAP_SIZE]; 129 ssp_cap->bLength = USB_DT_USB_SSP_CAP_SIZE(ssac); 130 ssp_cap->bDescriptorType = USB_DT_DEVICE_CAPABILITY; 131 ssp_cap->bDevCapabilityType = USB_SSP_CAP_TYPE; 132 ssp_cap->bReserved = 0; 133 ssp_cap->wReserved = 0; 134 ssp_cap->bmAttributes = 135 cpu_to_le32(FIELD_PREP(USB_SSP_SUBLINK_SPEED_ATTRIBS, ssac) | 136 FIELD_PREP(USB_SSP_SUBLINK_SPEED_IDS, ssic)); 137 138 if (!port_cap->psi_count) { 139 for (i = 0; i < ssac + 1; i++) 140 ssp_cap->bmSublinkSpeedAttr[i] = 141 cpu_to_le32(ssp_cap_default_ssa[i]); 142 143 min_ssid = 4; 144 goto out; 145 } 146 147 offset = 0; 148 for (i = 0; i < port_cap->psi_count; i++) { 149 u32 psi; 150 u32 attr; 151 u8 ssid; 152 u8 lp; 153 u8 lse; 154 u8 psie; 155 u16 lane_mantissa; 156 u16 psim; 157 u16 plt; 158 159 psi = port_cap->psi[i]; 160 ssid = XHCI_EXT_PORT_PSIV(psi); 161 lp = XHCI_EXT_PORT_LP(psi); 162 psie = XHCI_EXT_PORT_PSIE(psi); 163 psim = XHCI_EXT_PORT_PSIM(psi); 164 plt = psi & PLT_MASK; 165 166 lse = psie; 167 lane_mantissa = psim; 168 169 /* Shift to Gbps and set SSP Link Protocol if 10Gpbs */ 170 for (; psie < USB_SSP_SUBLINK_SPEED_LSE_GBPS; psie++) 171 psim /= 1000; 172 173 if (!min_rate || psim < min_rate) { 174 min_ssid = ssid; 175 min_rate = psim; 176 } 177 178 /* Some host controllers don't set the link protocol for SSP */ 179 if (psim >= 10) 180 lp = USB_SSP_SUBLINK_SPEED_LP_SSP; 181 182 /* 183 * PSIM and PSIE represent the total speed of PSI. The BOS 184 * descriptor SSP sublink speed attribute lane mantissa 185 * describes the lane speed. E.g. PSIM and PSIE for gen2x2 186 * is 20Gbps, but the BOS descriptor lane speed mantissa is 187 * 10Gbps. Check and modify the mantissa value to match the 188 * lane speed. 189 */ 190 if (bcdUSB == 0x0320 && plt == PLT_SYM) { 191 /* 192 * The PSI dword for gen1x2 and gen2x1 share the same 193 * values. But the lane speed for gen1x2 is 5Gbps while 194 * gen2x1 is 10Gbps. If the previous PSI dword SSID is 195 * 5 and the PSIE and PSIM match with SSID 6, let's 196 * assume that the controller follows the default speed 197 * id with SSID 6 for gen1x2. 198 */ 199 if (ssid == 6 && psie == 3 && psim == 10 && i) { 200 u32 prev = port_cap->psi[i - 1]; 201 202 if ((prev & PLT_MASK) == PLT_SYM && 203 XHCI_EXT_PORT_PSIV(prev) == 5 && 204 XHCI_EXT_PORT_PSIE(prev) == 3 && 205 XHCI_EXT_PORT_PSIM(prev) == 10) { 206 lse = USB_SSP_SUBLINK_SPEED_LSE_GBPS; 207 lane_mantissa = 5; 208 } 209 } 210 211 if (psie == 3 && psim > 10) { 212 lse = USB_SSP_SUBLINK_SPEED_LSE_GBPS; 213 lane_mantissa = 10; 214 } 215 } 216 217 attr = (FIELD_PREP(USB_SSP_SUBLINK_SPEED_SSID, ssid) | 218 FIELD_PREP(USB_SSP_SUBLINK_SPEED_LP, lp) | 219 FIELD_PREP(USB_SSP_SUBLINK_SPEED_LSE, lse) | 220 FIELD_PREP(USB_SSP_SUBLINK_SPEED_LSM, lane_mantissa)); 221 222 switch (plt) { 223 case PLT_SYM: 224 attr |= FIELD_PREP(USB_SSP_SUBLINK_SPEED_ST, 225 USB_SSP_SUBLINK_SPEED_ST_SYM_RX); 226 ssp_cap->bmSublinkSpeedAttr[offset++] = cpu_to_le32(attr); 227 228 attr &= ~USB_SSP_SUBLINK_SPEED_ST; 229 attr |= FIELD_PREP(USB_SSP_SUBLINK_SPEED_ST, 230 USB_SSP_SUBLINK_SPEED_ST_SYM_TX); 231 ssp_cap->bmSublinkSpeedAttr[offset++] = cpu_to_le32(attr); 232 break; 233 case PLT_ASYM_RX: 234 attr |= FIELD_PREP(USB_SSP_SUBLINK_SPEED_ST, 235 USB_SSP_SUBLINK_SPEED_ST_ASYM_RX); 236 ssp_cap->bmSublinkSpeedAttr[offset++] = cpu_to_le32(attr); 237 break; 238 case PLT_ASYM_TX: 239 attr |= FIELD_PREP(USB_SSP_SUBLINK_SPEED_ST, 240 USB_SSP_SUBLINK_SPEED_ST_ASYM_TX); 241 ssp_cap->bmSublinkSpeedAttr[offset++] = cpu_to_le32(attr); 242 break; 243 } 244 } 245 out: 246 ssp_cap->wFunctionalitySupport = 247 cpu_to_le16(FIELD_PREP(USB_SSP_MIN_SUBLINK_SPEED_ATTRIBUTE_ID, 248 min_ssid) | 249 FIELD_PREP(USB_SSP_MIN_RX_LANE_COUNT, 1) | 250 FIELD_PREP(USB_SSP_MIN_TX_LANE_COUNT, 1)); 251 252 return le16_to_cpu(bos->wTotalLength); 253 } 254 255 static void xhci_common_hub_descriptor(struct xhci_hcd *xhci, 256 struct usb_hub_descriptor *desc, int ports) 257 { 258 u16 temp; 259 260 desc->bHubContrCurrent = 0; 261 262 desc->bNbrPorts = ports; 263 temp = 0; 264 /* Bits 1:0 - support per-port power switching, or power always on */ 265 if (HCC_PPC(xhci->hcc_params)) 266 temp |= HUB_CHAR_INDV_PORT_LPSM; 267 else 268 temp |= HUB_CHAR_NO_LPSM; 269 /* Bit 2 - root hubs are not part of a compound device */ 270 /* Bits 4:3 - individual port over current protection */ 271 temp |= HUB_CHAR_INDV_PORT_OCPM; 272 /* Bits 6:5 - no TTs in root ports */ 273 /* Bit 7 - no port indicators */ 274 desc->wHubCharacteristics = cpu_to_le16(temp); 275 } 276 277 /* Fill in the USB 2.0 roothub descriptor */ 278 static void xhci_usb2_hub_descriptor(struct usb_hcd *hcd, struct xhci_hcd *xhci, 279 struct usb_hub_descriptor *desc) 280 { 281 int ports; 282 u16 temp; 283 __u8 port_removable[(USB_MAXCHILDREN + 1 + 7) / 8]; 284 u32 portsc; 285 unsigned int i; 286 struct xhci_hub *rhub; 287 288 rhub = &xhci->usb2_rhub; 289 ports = rhub->num_ports; 290 xhci_common_hub_descriptor(xhci, desc, ports); 291 desc->bDescriptorType = USB_DT_HUB; 292 temp = 1 + (ports / 8); 293 desc->bDescLength = USB_DT_HUB_NONVAR_SIZE + 2 * temp; 294 desc->bPwrOn2PwrGood = 10; /* xhci section 5.4.8 says 20ms */ 295 296 /* The Device Removable bits are reported on a byte granularity. 297 * If the port doesn't exist within that byte, the bit is set to 0. 298 */ 299 memset(port_removable, 0, sizeof(port_removable)); 300 for (i = 0; i < ports; i++) { 301 portsc = readl(rhub->ports[i]->addr); 302 /* If a device is removable, PORTSC reports a 0, same as in the 303 * hub descriptor DeviceRemovable bits. 304 */ 305 if (portsc & PORT_DEV_REMOVE) 306 /* This math is hairy because bit 0 of DeviceRemovable 307 * is reserved, and bit 1 is for port 1, etc. 308 */ 309 port_removable[(i + 1) / 8] |= 1 << ((i + 1) % 8); 310 } 311 312 /* ch11.h defines a hub descriptor that has room for USB_MAXCHILDREN 313 * ports on it. The USB 2.0 specification says that there are two 314 * variable length fields at the end of the hub descriptor: 315 * DeviceRemovable and PortPwrCtrlMask. But since we can have less than 316 * USB_MAXCHILDREN ports, we may need to use the DeviceRemovable array 317 * to set PortPwrCtrlMask bits. PortPwrCtrlMask must always be set to 318 * 0xFF, so we initialize the both arrays (DeviceRemovable and 319 * PortPwrCtrlMask) to 0xFF. Then we set the DeviceRemovable for each 320 * set of ports that actually exist. 321 */ 322 memset(desc->u.hs.DeviceRemovable, 0xff, 323 sizeof(desc->u.hs.DeviceRemovable)); 324 memset(desc->u.hs.PortPwrCtrlMask, 0xff, 325 sizeof(desc->u.hs.PortPwrCtrlMask)); 326 327 for (i = 0; i < (ports + 1 + 7) / 8; i++) 328 memset(&desc->u.hs.DeviceRemovable[i], port_removable[i], 329 sizeof(__u8)); 330 } 331 332 /* Fill in the USB 3.0 roothub descriptor */ 333 static void xhci_usb3_hub_descriptor(struct usb_hcd *hcd, struct xhci_hcd *xhci, 334 struct usb_hub_descriptor *desc) 335 { 336 int ports; 337 u16 port_removable; 338 u32 portsc; 339 unsigned int i; 340 struct xhci_hub *rhub; 341 342 rhub = &xhci->usb3_rhub; 343 ports = rhub->num_ports; 344 xhci_common_hub_descriptor(xhci, desc, ports); 345 desc->bDescriptorType = USB_DT_SS_HUB; 346 desc->bDescLength = USB_DT_SS_HUB_SIZE; 347 desc->bPwrOn2PwrGood = 50; /* usb 3.1 may fail if less than 100ms */ 348 349 /* header decode latency should be zero for roothubs, 350 * see section 4.23.5.2. 351 */ 352 desc->u.ss.bHubHdrDecLat = 0; 353 desc->u.ss.wHubDelay = 0; 354 355 port_removable = 0; 356 /* bit 0 is reserved, bit 1 is for port 1, etc. */ 357 for (i = 0; i < ports; i++) { 358 portsc = readl(rhub->ports[i]->addr); 359 if (portsc & PORT_DEV_REMOVE) 360 port_removable |= 1 << (i + 1); 361 } 362 363 desc->u.ss.DeviceRemovable = cpu_to_le16(port_removable); 364 } 365 366 static void xhci_hub_descriptor(struct usb_hcd *hcd, struct xhci_hcd *xhci, 367 struct usb_hub_descriptor *desc) 368 { 369 370 if (hcd->speed >= HCD_USB3) 371 xhci_usb3_hub_descriptor(hcd, xhci, desc); 372 else 373 xhci_usb2_hub_descriptor(hcd, xhci, desc); 374 375 } 376 377 static unsigned int xhci_port_speed(unsigned int port_status) 378 { 379 if (DEV_LOWSPEED(port_status)) 380 return USB_PORT_STAT_LOW_SPEED; 381 if (DEV_HIGHSPEED(port_status)) 382 return USB_PORT_STAT_HIGH_SPEED; 383 /* 384 * FIXME: Yes, we should check for full speed, but the core uses that as 385 * a default in portspeed() in usb/core/hub.c (which is the only place 386 * USB_PORT_STAT_*_SPEED is used). 387 */ 388 return 0; 389 } 390 391 /* 392 * These bits are Read Only (RO) and should be saved and written to the 393 * registers: 0, 3, 10:13, 30 394 * connect status, over-current status, port speed, and device removable. 395 * connect status and port speed are also sticky - meaning they're in 396 * the AUX well and they aren't changed by a hot, warm, or cold reset. 397 */ 398 #define XHCI_PORT_RO ((1<<0) | (1<<3) | (0xf<<10) | (1<<30)) 399 /* 400 * These bits are RW; writing a 0 clears the bit, writing a 1 sets the bit: 401 * bits 5:8, 9, 14:15, 25:27 402 * link state, port power, port indicator state, "wake on" enable state 403 */ 404 #define XHCI_PORT_RWS ((0xf<<5) | (1<<9) | (0x3<<14) | (0x7<<25)) 405 /* 406 * These bits are RW; writing a 1 sets the bit, writing a 0 has no effect: 407 * bit 4 (port reset) 408 */ 409 #define XHCI_PORT_RW1S ((1<<4)) 410 /* 411 * These bits are RW; writing a 1 clears the bit, writing a 0 has no effect: 412 * bits 1, 17, 18, 19, 20, 21, 22, 23 413 * port enable/disable, and 414 * change bits: connect, PED, warm port reset changed (reserved zero for USB 2.0 ports), 415 * over-current, reset, link state, and L1 change 416 */ 417 #define XHCI_PORT_RW1CS ((1<<1) | (0x7f<<17)) 418 /* 419 * Bit 16 is RW, and writing a '1' to it causes the link state control to be 420 * latched in 421 */ 422 #define XHCI_PORT_RW ((1<<16)) 423 /* 424 * These bits are Reserved Zero (RsvdZ) and zero should be written to them: 425 * bits 2, 24, 28:31 426 */ 427 #define XHCI_PORT_RZ ((1<<2) | (1<<24) | (0xf<<28)) 428 429 /* 430 * Given a port state, this function returns a value that would result in the 431 * port being in the same state, if the value was written to the port status 432 * control register. 433 * Save Read Only (RO) bits and save read/write bits where 434 * writing a 0 clears the bit and writing a 1 sets the bit (RWS). 435 * For all other types (RW1S, RW1CS, RW, and RZ), writing a '0' has no effect. 436 */ 437 u32 xhci_port_state_to_neutral(u32 state) 438 { 439 /* Save read-only status and port state */ 440 return (state & XHCI_PORT_RO) | (state & XHCI_PORT_RWS); 441 } 442 443 /* 444 * find slot id based on port number. 445 * @port: The one-based port number from one of the two split roothubs. 446 */ 447 int xhci_find_slot_id_by_port(struct usb_hcd *hcd, struct xhci_hcd *xhci, 448 u16 port) 449 { 450 int slot_id; 451 int i; 452 enum usb_device_speed speed; 453 454 slot_id = 0; 455 for (i = 0; i < MAX_HC_SLOTS; i++) { 456 if (!xhci->devs[i] || !xhci->devs[i]->udev) 457 continue; 458 speed = xhci->devs[i]->udev->speed; 459 if (((speed >= USB_SPEED_SUPER) == (hcd->speed >= HCD_USB3)) 460 && xhci->devs[i]->fake_port == port) { 461 slot_id = i; 462 break; 463 } 464 } 465 466 return slot_id; 467 } 468 469 /* 470 * Stop device 471 * It issues stop endpoint command for EP 0 to 30. And wait the last command 472 * to complete. 473 * suspend will set to 1, if suspend bit need to set in command. 474 */ 475 static int xhci_stop_device(struct xhci_hcd *xhci, int slot_id, int suspend) 476 { 477 struct xhci_virt_device *virt_dev; 478 struct xhci_command *cmd; 479 unsigned long flags; 480 int ret; 481 int i; 482 483 ret = 0; 484 virt_dev = xhci->devs[slot_id]; 485 if (!virt_dev) 486 return -ENODEV; 487 488 trace_xhci_stop_device(virt_dev); 489 490 cmd = xhci_alloc_command(xhci, true, GFP_NOIO); 491 if (!cmd) 492 return -ENOMEM; 493 494 spin_lock_irqsave(&xhci->lock, flags); 495 for (i = LAST_EP_INDEX; i > 0; i--) { 496 if (virt_dev->eps[i].ring && virt_dev->eps[i].ring->dequeue) { 497 struct xhci_ep_ctx *ep_ctx; 498 struct xhci_command *command; 499 500 ep_ctx = xhci_get_ep_ctx(xhci, virt_dev->out_ctx, i); 501 502 /* Check ep is running, required by AMD SNPS 3.1 xHC */ 503 if (GET_EP_CTX_STATE(ep_ctx) != EP_STATE_RUNNING) 504 continue; 505 506 command = xhci_alloc_command(xhci, false, GFP_NOWAIT); 507 if (!command) { 508 spin_unlock_irqrestore(&xhci->lock, flags); 509 ret = -ENOMEM; 510 goto cmd_cleanup; 511 } 512 513 ret = xhci_queue_stop_endpoint(xhci, command, slot_id, 514 i, suspend); 515 if (ret) { 516 spin_unlock_irqrestore(&xhci->lock, flags); 517 xhci_free_command(xhci, command); 518 goto cmd_cleanup; 519 } 520 } 521 } 522 ret = xhci_queue_stop_endpoint(xhci, cmd, slot_id, 0, suspend); 523 if (ret) { 524 spin_unlock_irqrestore(&xhci->lock, flags); 525 goto cmd_cleanup; 526 } 527 528 xhci_ring_cmd_db(xhci); 529 spin_unlock_irqrestore(&xhci->lock, flags); 530 531 /* Wait for last stop endpoint command to finish */ 532 wait_for_completion(cmd->completion); 533 534 if (cmd->status == COMP_COMMAND_ABORTED || 535 cmd->status == COMP_COMMAND_RING_STOPPED) { 536 xhci_warn(xhci, "Timeout while waiting for stop endpoint command\n"); 537 ret = -ETIME; 538 } 539 540 cmd_cleanup: 541 xhci_free_command(xhci, cmd); 542 return ret; 543 } 544 545 /* 546 * Ring device, it rings the all doorbells unconditionally. 547 */ 548 void xhci_ring_device(struct xhci_hcd *xhci, int slot_id) 549 { 550 int i, s; 551 struct xhci_virt_ep *ep; 552 553 for (i = 0; i < LAST_EP_INDEX + 1; i++) { 554 ep = &xhci->devs[slot_id]->eps[i]; 555 556 if (ep->ep_state & EP_HAS_STREAMS) { 557 for (s = 1; s < ep->stream_info->num_streams; s++) 558 xhci_ring_ep_doorbell(xhci, slot_id, i, s); 559 } else if (ep->ring && ep->ring->dequeue) { 560 xhci_ring_ep_doorbell(xhci, slot_id, i, 0); 561 } 562 } 563 564 return; 565 } 566 567 static void xhci_disable_port(struct usb_hcd *hcd, struct xhci_hcd *xhci, 568 u16 wIndex, __le32 __iomem *addr, u32 port_status) 569 { 570 /* Don't allow the USB core to disable SuperSpeed ports. */ 571 if (hcd->speed >= HCD_USB3) { 572 xhci_dbg(xhci, "Ignoring request to disable " 573 "SuperSpeed port.\n"); 574 return; 575 } 576 577 if (xhci->quirks & XHCI_BROKEN_PORT_PED) { 578 xhci_dbg(xhci, 579 "Broken Port Enabled/Disabled, ignoring port disable request.\n"); 580 return; 581 } 582 583 /* Write 1 to disable the port */ 584 writel(port_status | PORT_PE, addr); 585 port_status = readl(addr); 586 xhci_dbg(xhci, "disable port %d-%d, portsc: 0x%x\n", 587 hcd->self.busnum, wIndex + 1, port_status); 588 } 589 590 static void xhci_clear_port_change_bit(struct xhci_hcd *xhci, u16 wValue, 591 u16 wIndex, __le32 __iomem *addr, u32 port_status) 592 { 593 char *port_change_bit; 594 u32 status; 595 596 switch (wValue) { 597 case USB_PORT_FEAT_C_RESET: 598 status = PORT_RC; 599 port_change_bit = "reset"; 600 break; 601 case USB_PORT_FEAT_C_BH_PORT_RESET: 602 status = PORT_WRC; 603 port_change_bit = "warm(BH) reset"; 604 break; 605 case USB_PORT_FEAT_C_CONNECTION: 606 status = PORT_CSC; 607 port_change_bit = "connect"; 608 break; 609 case USB_PORT_FEAT_C_OVER_CURRENT: 610 status = PORT_OCC; 611 port_change_bit = "over-current"; 612 break; 613 case USB_PORT_FEAT_C_ENABLE: 614 status = PORT_PEC; 615 port_change_bit = "enable/disable"; 616 break; 617 case USB_PORT_FEAT_C_SUSPEND: 618 status = PORT_PLC; 619 port_change_bit = "suspend/resume"; 620 break; 621 case USB_PORT_FEAT_C_PORT_LINK_STATE: 622 status = PORT_PLC; 623 port_change_bit = "link state"; 624 break; 625 case USB_PORT_FEAT_C_PORT_CONFIG_ERROR: 626 status = PORT_CEC; 627 port_change_bit = "config error"; 628 break; 629 default: 630 /* Should never happen */ 631 return; 632 } 633 /* Change bits are all write 1 to clear */ 634 writel(port_status | status, addr); 635 port_status = readl(addr); 636 637 xhci_dbg(xhci, "clear port%d %s change, portsc: 0x%x\n", 638 wIndex + 1, port_change_bit, port_status); 639 } 640 641 struct xhci_hub *xhci_get_rhub(struct usb_hcd *hcd) 642 { 643 struct xhci_hcd *xhci = hcd_to_xhci(hcd); 644 645 if (hcd->speed >= HCD_USB3) 646 return &xhci->usb3_rhub; 647 return &xhci->usb2_rhub; 648 } 649 650 /* 651 * xhci_set_port_power() must be called with xhci->lock held. 652 * It will release and re-aquire the lock while calling ACPI 653 * method. 654 */ 655 static void xhci_set_port_power(struct xhci_hcd *xhci, struct usb_hcd *hcd, 656 u16 index, bool on, unsigned long *flags) 657 __must_hold(&xhci->lock) 658 { 659 struct xhci_hub *rhub; 660 struct xhci_port *port; 661 u32 temp; 662 663 rhub = xhci_get_rhub(hcd); 664 port = rhub->ports[index]; 665 temp = readl(port->addr); 666 667 xhci_dbg(xhci, "set port power %d-%d %s, portsc: 0x%x\n", 668 hcd->self.busnum, index + 1, on ? "ON" : "OFF", temp); 669 670 temp = xhci_port_state_to_neutral(temp); 671 672 if (on) { 673 /* Power on */ 674 writel(temp | PORT_POWER, port->addr); 675 readl(port->addr); 676 } else { 677 /* Power off */ 678 writel(temp & ~PORT_POWER, port->addr); 679 } 680 681 spin_unlock_irqrestore(&xhci->lock, *flags); 682 temp = usb_acpi_power_manageable(hcd->self.root_hub, 683 index); 684 if (temp) 685 usb_acpi_set_power_state(hcd->self.root_hub, 686 index, on); 687 spin_lock_irqsave(&xhci->lock, *flags); 688 } 689 690 static void xhci_port_set_test_mode(struct xhci_hcd *xhci, 691 u16 test_mode, u16 wIndex) 692 { 693 u32 temp; 694 struct xhci_port *port; 695 696 /* xhci only supports test mode for usb2 ports */ 697 port = xhci->usb2_rhub.ports[wIndex]; 698 temp = readl(port->addr + PORTPMSC); 699 temp |= test_mode << PORT_TEST_MODE_SHIFT; 700 writel(temp, port->addr + PORTPMSC); 701 xhci->test_mode = test_mode; 702 if (test_mode == USB_TEST_FORCE_ENABLE) 703 xhci_start(xhci); 704 } 705 706 static int xhci_enter_test_mode(struct xhci_hcd *xhci, 707 u16 test_mode, u16 wIndex, unsigned long *flags) 708 __must_hold(&xhci->lock) 709 { 710 int i, retval; 711 712 /* Disable all Device Slots */ 713 xhci_dbg(xhci, "Disable all slots\n"); 714 spin_unlock_irqrestore(&xhci->lock, *flags); 715 for (i = 1; i <= HCS_MAX_SLOTS(xhci->hcs_params1); i++) { 716 if (!xhci->devs[i]) 717 continue; 718 719 retval = xhci_disable_slot(xhci, i); 720 xhci_free_virt_device(xhci, i); 721 if (retval) 722 xhci_err(xhci, "Failed to disable slot %d, %d. Enter test mode anyway\n", 723 i, retval); 724 } 725 spin_lock_irqsave(&xhci->lock, *flags); 726 /* Put all ports to the Disable state by clear PP */ 727 xhci_dbg(xhci, "Disable all port (PP = 0)\n"); 728 /* Power off USB3 ports*/ 729 for (i = 0; i < xhci->usb3_rhub.num_ports; i++) 730 xhci_set_port_power(xhci, xhci->shared_hcd, i, false, flags); 731 /* Power off USB2 ports*/ 732 for (i = 0; i < xhci->usb2_rhub.num_ports; i++) 733 xhci_set_port_power(xhci, xhci->main_hcd, i, false, flags); 734 /* Stop the controller */ 735 xhci_dbg(xhci, "Stop controller\n"); 736 retval = xhci_halt(xhci); 737 if (retval) 738 return retval; 739 /* Disable runtime PM for test mode */ 740 pm_runtime_forbid(xhci_to_hcd(xhci)->self.controller); 741 /* Set PORTPMSC.PTC field to enter selected test mode */ 742 /* Port is selected by wIndex. port_id = wIndex + 1 */ 743 xhci_dbg(xhci, "Enter Test Mode: %d, Port_id=%d\n", 744 test_mode, wIndex + 1); 745 xhci_port_set_test_mode(xhci, test_mode, wIndex); 746 return retval; 747 } 748 749 static int xhci_exit_test_mode(struct xhci_hcd *xhci) 750 { 751 int retval; 752 753 if (!xhci->test_mode) { 754 xhci_err(xhci, "Not in test mode, do nothing.\n"); 755 return 0; 756 } 757 if (xhci->test_mode == USB_TEST_FORCE_ENABLE && 758 !(xhci->xhc_state & XHCI_STATE_HALTED)) { 759 retval = xhci_halt(xhci); 760 if (retval) 761 return retval; 762 } 763 pm_runtime_allow(xhci_to_hcd(xhci)->self.controller); 764 xhci->test_mode = 0; 765 return xhci_reset(xhci, XHCI_RESET_SHORT_USEC); 766 } 767 768 void xhci_set_link_state(struct xhci_hcd *xhci, struct xhci_port *port, 769 u32 link_state) 770 { 771 u32 temp; 772 u32 portsc; 773 774 portsc = readl(port->addr); 775 temp = xhci_port_state_to_neutral(portsc); 776 temp &= ~PORT_PLS_MASK; 777 temp |= PORT_LINK_STROBE | link_state; 778 writel(temp, port->addr); 779 780 xhci_dbg(xhci, "Set port %d-%d link state, portsc: 0x%x, write 0x%x", 781 port->rhub->hcd->self.busnum, port->hcd_portnum + 1, 782 portsc, temp); 783 } 784 785 static void xhci_set_remote_wake_mask(struct xhci_hcd *xhci, 786 struct xhci_port *port, u16 wake_mask) 787 { 788 u32 temp; 789 790 temp = readl(port->addr); 791 temp = xhci_port_state_to_neutral(temp); 792 793 if (wake_mask & USB_PORT_FEAT_REMOTE_WAKE_CONNECT) 794 temp |= PORT_WKCONN_E; 795 else 796 temp &= ~PORT_WKCONN_E; 797 798 if (wake_mask & USB_PORT_FEAT_REMOTE_WAKE_DISCONNECT) 799 temp |= PORT_WKDISC_E; 800 else 801 temp &= ~PORT_WKDISC_E; 802 803 if (wake_mask & USB_PORT_FEAT_REMOTE_WAKE_OVER_CURRENT) 804 temp |= PORT_WKOC_E; 805 else 806 temp &= ~PORT_WKOC_E; 807 808 writel(temp, port->addr); 809 } 810 811 /* Test and clear port RWC bit */ 812 void xhci_test_and_clear_bit(struct xhci_hcd *xhci, struct xhci_port *port, 813 u32 port_bit) 814 { 815 u32 temp; 816 817 temp = readl(port->addr); 818 if (temp & port_bit) { 819 temp = xhci_port_state_to_neutral(temp); 820 temp |= port_bit; 821 writel(temp, port->addr); 822 } 823 } 824 825 /* Updates Link Status for super Speed port */ 826 static void xhci_hub_report_usb3_link_state(struct xhci_hcd *xhci, 827 u32 *status, u32 status_reg) 828 { 829 u32 pls = status_reg & PORT_PLS_MASK; 830 831 /* When the CAS bit is set then warm reset 832 * should be performed on port 833 */ 834 if (status_reg & PORT_CAS) { 835 /* The CAS bit can be set while the port is 836 * in any link state. 837 * Only roothubs have CAS bit, so we 838 * pretend to be in compliance mode 839 * unless we're already in compliance 840 * or the inactive state. 841 */ 842 if (pls != USB_SS_PORT_LS_COMP_MOD && 843 pls != USB_SS_PORT_LS_SS_INACTIVE) { 844 pls = USB_SS_PORT_LS_COMP_MOD; 845 } 846 /* Return also connection bit - 847 * hub state machine resets port 848 * when this bit is set. 849 */ 850 pls |= USB_PORT_STAT_CONNECTION; 851 } else { 852 /* 853 * Resume state is an xHCI internal state. Do not report it to 854 * usb core, instead, pretend to be U3, thus usb core knows 855 * it's not ready for transfer. 856 */ 857 if (pls == XDEV_RESUME) { 858 *status |= USB_SS_PORT_LS_U3; 859 return; 860 } 861 862 /* 863 * If CAS bit isn't set but the Port is already at 864 * Compliance Mode, fake a connection so the USB core 865 * notices the Compliance state and resets the port. 866 * This resolves an issue generated by the SN65LVPE502CP 867 * in which sometimes the port enters compliance mode 868 * caused by a delay on the host-device negotiation. 869 */ 870 if ((xhci->quirks & XHCI_COMP_MODE_QUIRK) && 871 (pls == USB_SS_PORT_LS_COMP_MOD)) 872 pls |= USB_PORT_STAT_CONNECTION; 873 } 874 875 /* update status field */ 876 *status |= pls; 877 } 878 879 /* 880 * Function for Compliance Mode Quirk. 881 * 882 * This Function verifies if all xhc USB3 ports have entered U0, if so, 883 * the compliance mode timer is deleted. A port won't enter 884 * compliance mode if it has previously entered U0. 885 */ 886 static void xhci_del_comp_mod_timer(struct xhci_hcd *xhci, u32 status, 887 u16 wIndex) 888 { 889 u32 all_ports_seen_u0 = ((1 << xhci->usb3_rhub.num_ports) - 1); 890 bool port_in_u0 = ((status & PORT_PLS_MASK) == XDEV_U0); 891 892 if (!(xhci->quirks & XHCI_COMP_MODE_QUIRK)) 893 return; 894 895 if ((xhci->port_status_u0 != all_ports_seen_u0) && port_in_u0) { 896 xhci->port_status_u0 |= 1 << wIndex; 897 if (xhci->port_status_u0 == all_ports_seen_u0) { 898 del_timer_sync(&xhci->comp_mode_recovery_timer); 899 xhci_dbg_trace(xhci, trace_xhci_dbg_quirks, 900 "All USB3 ports have entered U0 already!"); 901 xhci_dbg_trace(xhci, trace_xhci_dbg_quirks, 902 "Compliance Mode Recovery Timer Deleted."); 903 } 904 } 905 } 906 907 static int xhci_handle_usb2_port_link_resume(struct xhci_port *port, 908 u32 *status, u32 portsc, 909 unsigned long *flags) 910 { 911 struct xhci_bus_state *bus_state; 912 struct xhci_hcd *xhci; 913 struct usb_hcd *hcd; 914 int slot_id; 915 u32 wIndex; 916 917 hcd = port->rhub->hcd; 918 bus_state = &port->rhub->bus_state; 919 xhci = hcd_to_xhci(hcd); 920 wIndex = port->hcd_portnum; 921 922 if ((portsc & PORT_RESET) || !(portsc & PORT_PE)) { 923 *status = 0xffffffff; 924 return -EINVAL; 925 } 926 /* did port event handler already start resume timing? */ 927 if (!bus_state->resume_done[wIndex]) { 928 /* If not, maybe we are in a host initated resume? */ 929 if (test_bit(wIndex, &bus_state->resuming_ports)) { 930 /* Host initated resume doesn't time the resume 931 * signalling using resume_done[]. 932 * It manually sets RESUME state, sleeps 20ms 933 * and sets U0 state. This should probably be 934 * changed, but not right now. 935 */ 936 } else { 937 /* port resume was discovered now and here, 938 * start resume timing 939 */ 940 unsigned long timeout = jiffies + 941 msecs_to_jiffies(USB_RESUME_TIMEOUT); 942 943 set_bit(wIndex, &bus_state->resuming_ports); 944 bus_state->resume_done[wIndex] = timeout; 945 mod_timer(&hcd->rh_timer, timeout); 946 usb_hcd_start_port_resume(&hcd->self, wIndex); 947 } 948 /* Has resume been signalled for USB_RESUME_TIME yet? */ 949 } else if (time_after_eq(jiffies, bus_state->resume_done[wIndex])) { 950 int time_left; 951 952 xhci_dbg(xhci, "resume USB2 port %d-%d\n", 953 hcd->self.busnum, wIndex + 1); 954 955 bus_state->resume_done[wIndex] = 0; 956 clear_bit(wIndex, &bus_state->resuming_ports); 957 958 set_bit(wIndex, &bus_state->rexit_ports); 959 960 xhci_test_and_clear_bit(xhci, port, PORT_PLC); 961 xhci_set_link_state(xhci, port, XDEV_U0); 962 963 spin_unlock_irqrestore(&xhci->lock, *flags); 964 time_left = wait_for_completion_timeout( 965 &bus_state->rexit_done[wIndex], 966 msecs_to_jiffies(XHCI_MAX_REXIT_TIMEOUT_MS)); 967 spin_lock_irqsave(&xhci->lock, *flags); 968 969 if (time_left) { 970 slot_id = xhci_find_slot_id_by_port(hcd, xhci, 971 wIndex + 1); 972 if (!slot_id) { 973 xhci_dbg(xhci, "slot_id is zero\n"); 974 *status = 0xffffffff; 975 return -ENODEV; 976 } 977 xhci_ring_device(xhci, slot_id); 978 } else { 979 int port_status = readl(port->addr); 980 981 xhci_warn(xhci, "Port resume timed out, port %d-%d: 0x%x\n", 982 hcd->self.busnum, wIndex + 1, port_status); 983 *status |= USB_PORT_STAT_SUSPEND; 984 clear_bit(wIndex, &bus_state->rexit_ports); 985 } 986 987 usb_hcd_end_port_resume(&hcd->self, wIndex); 988 bus_state->port_c_suspend |= 1 << wIndex; 989 bus_state->suspended_ports &= ~(1 << wIndex); 990 } else { 991 /* 992 * The resume has been signaling for less than 993 * USB_RESUME_TIME. Report the port status as SUSPEND, 994 * let the usbcore check port status again and clear 995 * resume signaling later. 996 */ 997 *status |= USB_PORT_STAT_SUSPEND; 998 } 999 return 0; 1000 } 1001 1002 static u32 xhci_get_ext_port_status(u32 raw_port_status, u32 port_li) 1003 { 1004 u32 ext_stat = 0; 1005 int speed_id; 1006 1007 /* only support rx and tx lane counts of 1 in usb3.1 spec */ 1008 speed_id = DEV_PORT_SPEED(raw_port_status); 1009 ext_stat |= speed_id; /* bits 3:0, RX speed id */ 1010 ext_stat |= speed_id << 4; /* bits 7:4, TX speed id */ 1011 1012 ext_stat |= PORT_RX_LANES(port_li) << 8; /* bits 11:8 Rx lane count */ 1013 ext_stat |= PORT_TX_LANES(port_li) << 12; /* bits 15:12 Tx lane count */ 1014 1015 return ext_stat; 1016 } 1017 1018 static void xhci_get_usb3_port_status(struct xhci_port *port, u32 *status, 1019 u32 portsc) 1020 { 1021 struct xhci_bus_state *bus_state; 1022 struct xhci_hcd *xhci; 1023 struct usb_hcd *hcd; 1024 u32 link_state; 1025 u32 portnum; 1026 1027 bus_state = &port->rhub->bus_state; 1028 xhci = hcd_to_xhci(port->rhub->hcd); 1029 hcd = port->rhub->hcd; 1030 link_state = portsc & PORT_PLS_MASK; 1031 portnum = port->hcd_portnum; 1032 1033 /* USB3 specific wPortChange bits 1034 * 1035 * Port link change with port in resume state should not be 1036 * reported to usbcore, as this is an internal state to be 1037 * handled by xhci driver. Reporting PLC to usbcore may 1038 * cause usbcore clearing PLC first and port change event 1039 * irq won't be generated. 1040 */ 1041 1042 if (portsc & PORT_PLC && (link_state != XDEV_RESUME)) 1043 *status |= USB_PORT_STAT_C_LINK_STATE << 16; 1044 if (portsc & PORT_WRC) 1045 *status |= USB_PORT_STAT_C_BH_RESET << 16; 1046 if (portsc & PORT_CEC) 1047 *status |= USB_PORT_STAT_C_CONFIG_ERROR << 16; 1048 1049 /* USB3 specific wPortStatus bits */ 1050 if (portsc & PORT_POWER) { 1051 *status |= USB_SS_PORT_STAT_POWER; 1052 /* link state handling */ 1053 if (link_state == XDEV_U0) 1054 bus_state->suspended_ports &= ~(1 << portnum); 1055 } 1056 1057 /* remote wake resume signaling complete */ 1058 if (bus_state->port_remote_wakeup & (1 << portnum) && 1059 link_state != XDEV_RESUME && 1060 link_state != XDEV_RECOVERY) { 1061 bus_state->port_remote_wakeup &= ~(1 << portnum); 1062 usb_hcd_end_port_resume(&hcd->self, portnum); 1063 } 1064 1065 xhci_hub_report_usb3_link_state(xhci, status, portsc); 1066 xhci_del_comp_mod_timer(xhci, portsc, portnum); 1067 } 1068 1069 static void xhci_get_usb2_port_status(struct xhci_port *port, u32 *status, 1070 u32 portsc, unsigned long *flags) 1071 { 1072 struct xhci_bus_state *bus_state; 1073 u32 link_state; 1074 u32 portnum; 1075 int ret; 1076 1077 bus_state = &port->rhub->bus_state; 1078 link_state = portsc & PORT_PLS_MASK; 1079 portnum = port->hcd_portnum; 1080 1081 /* USB2 wPortStatus bits */ 1082 if (portsc & PORT_POWER) { 1083 *status |= USB_PORT_STAT_POWER; 1084 1085 /* link state is only valid if port is powered */ 1086 if (link_state == XDEV_U3) 1087 *status |= USB_PORT_STAT_SUSPEND; 1088 if (link_state == XDEV_U2) 1089 *status |= USB_PORT_STAT_L1; 1090 if (link_state == XDEV_U0) { 1091 if (bus_state->resume_done[portnum]) 1092 usb_hcd_end_port_resume(&port->rhub->hcd->self, 1093 portnum); 1094 bus_state->resume_done[portnum] = 0; 1095 clear_bit(portnum, &bus_state->resuming_ports); 1096 if (bus_state->suspended_ports & (1 << portnum)) { 1097 bus_state->suspended_ports &= ~(1 << portnum); 1098 bus_state->port_c_suspend |= 1 << portnum; 1099 } 1100 } 1101 if (link_state == XDEV_RESUME) { 1102 ret = xhci_handle_usb2_port_link_resume(port, status, 1103 portsc, flags); 1104 if (ret) 1105 return; 1106 } 1107 } 1108 } 1109 1110 /* 1111 * Converts a raw xHCI port status into the format that external USB 2.0 or USB 1112 * 3.0 hubs use. 1113 * 1114 * Possible side effects: 1115 * - Mark a port as being done with device resume, 1116 * and ring the endpoint doorbells. 1117 * - Stop the Synopsys redriver Compliance Mode polling. 1118 * - Drop and reacquire the xHCI lock, in order to wait for port resume. 1119 */ 1120 static u32 xhci_get_port_status(struct usb_hcd *hcd, 1121 struct xhci_bus_state *bus_state, 1122 u16 wIndex, u32 raw_port_status, 1123 unsigned long *flags) 1124 __releases(&xhci->lock) 1125 __acquires(&xhci->lock) 1126 { 1127 u32 status = 0; 1128 struct xhci_hub *rhub; 1129 struct xhci_port *port; 1130 1131 rhub = xhci_get_rhub(hcd); 1132 port = rhub->ports[wIndex]; 1133 1134 /* common wPortChange bits */ 1135 if (raw_port_status & PORT_CSC) 1136 status |= USB_PORT_STAT_C_CONNECTION << 16; 1137 if (raw_port_status & PORT_PEC) 1138 status |= USB_PORT_STAT_C_ENABLE << 16; 1139 if ((raw_port_status & PORT_OCC)) 1140 status |= USB_PORT_STAT_C_OVERCURRENT << 16; 1141 if ((raw_port_status & PORT_RC)) 1142 status |= USB_PORT_STAT_C_RESET << 16; 1143 1144 /* common wPortStatus bits */ 1145 if (raw_port_status & PORT_CONNECT) { 1146 status |= USB_PORT_STAT_CONNECTION; 1147 status |= xhci_port_speed(raw_port_status); 1148 } 1149 if (raw_port_status & PORT_PE) 1150 status |= USB_PORT_STAT_ENABLE; 1151 if (raw_port_status & PORT_OC) 1152 status |= USB_PORT_STAT_OVERCURRENT; 1153 if (raw_port_status & PORT_RESET) 1154 status |= USB_PORT_STAT_RESET; 1155 1156 /* USB2 and USB3 specific bits, including Port Link State */ 1157 if (hcd->speed >= HCD_USB3) 1158 xhci_get_usb3_port_status(port, &status, raw_port_status); 1159 else 1160 xhci_get_usb2_port_status(port, &status, raw_port_status, 1161 flags); 1162 /* 1163 * Clear stale usb2 resume signalling variables in case port changed 1164 * state during resume signalling. For example on error 1165 */ 1166 if ((bus_state->resume_done[wIndex] || 1167 test_bit(wIndex, &bus_state->resuming_ports)) && 1168 (raw_port_status & PORT_PLS_MASK) != XDEV_U3 && 1169 (raw_port_status & PORT_PLS_MASK) != XDEV_RESUME) { 1170 bus_state->resume_done[wIndex] = 0; 1171 clear_bit(wIndex, &bus_state->resuming_ports); 1172 usb_hcd_end_port_resume(&hcd->self, wIndex); 1173 } 1174 1175 if (bus_state->port_c_suspend & (1 << wIndex)) 1176 status |= USB_PORT_STAT_C_SUSPEND << 16; 1177 1178 return status; 1179 } 1180 1181 int xhci_hub_control(struct usb_hcd *hcd, u16 typeReq, u16 wValue, 1182 u16 wIndex, char *buf, u16 wLength) 1183 { 1184 struct xhci_hcd *xhci = hcd_to_xhci(hcd); 1185 int max_ports; 1186 unsigned long flags; 1187 u32 temp, status; 1188 int retval = 0; 1189 int slot_id; 1190 struct xhci_bus_state *bus_state; 1191 u16 link_state = 0; 1192 u16 wake_mask = 0; 1193 u16 timeout = 0; 1194 u16 test_mode = 0; 1195 struct xhci_hub *rhub; 1196 struct xhci_port **ports; 1197 1198 rhub = xhci_get_rhub(hcd); 1199 ports = rhub->ports; 1200 max_ports = rhub->num_ports; 1201 bus_state = &rhub->bus_state; 1202 1203 spin_lock_irqsave(&xhci->lock, flags); 1204 switch (typeReq) { 1205 case GetHubStatus: 1206 /* No power source, over-current reported per port */ 1207 memset(buf, 0, 4); 1208 break; 1209 case GetHubDescriptor: 1210 /* Check to make sure userspace is asking for the USB 3.0 hub 1211 * descriptor for the USB 3.0 roothub. If not, we stall the 1212 * endpoint, like external hubs do. 1213 */ 1214 if (hcd->speed >= HCD_USB3 && 1215 (wLength < USB_DT_SS_HUB_SIZE || 1216 wValue != (USB_DT_SS_HUB << 8))) { 1217 xhci_dbg(xhci, "Wrong hub descriptor type for " 1218 "USB 3.0 roothub.\n"); 1219 goto error; 1220 } 1221 xhci_hub_descriptor(hcd, xhci, 1222 (struct usb_hub_descriptor *) buf); 1223 break; 1224 case DeviceRequest | USB_REQ_GET_DESCRIPTOR: 1225 if ((wValue & 0xff00) != (USB_DT_BOS << 8)) 1226 goto error; 1227 1228 if (hcd->speed < HCD_USB3) 1229 goto error; 1230 1231 retval = xhci_create_usb3x_bos_desc(xhci, buf, wLength); 1232 spin_unlock_irqrestore(&xhci->lock, flags); 1233 return retval; 1234 case GetPortStatus: 1235 if (!wIndex || wIndex > max_ports) 1236 goto error; 1237 wIndex--; 1238 temp = readl(ports[wIndex]->addr); 1239 if (temp == ~(u32)0) { 1240 xhci_hc_died(xhci); 1241 retval = -ENODEV; 1242 break; 1243 } 1244 trace_xhci_get_port_status(wIndex, temp); 1245 status = xhci_get_port_status(hcd, bus_state, wIndex, temp, 1246 &flags); 1247 if (status == 0xffffffff) 1248 goto error; 1249 1250 xhci_dbg(xhci, "Get port status %d-%d read: 0x%x, return 0x%x", 1251 hcd->self.busnum, wIndex + 1, temp, status); 1252 1253 put_unaligned(cpu_to_le32(status), (__le32 *) buf); 1254 /* if USB 3.1 extended port status return additional 4 bytes */ 1255 if (wValue == 0x02) { 1256 u32 port_li; 1257 1258 if (hcd->speed < HCD_USB31 || wLength != 8) { 1259 xhci_err(xhci, "get ext port status invalid parameter\n"); 1260 retval = -EINVAL; 1261 break; 1262 } 1263 port_li = readl(ports[wIndex]->addr + PORTLI); 1264 status = xhci_get_ext_port_status(temp, port_li); 1265 put_unaligned_le32(status, &buf[4]); 1266 } 1267 break; 1268 case SetPortFeature: 1269 if (wValue == USB_PORT_FEAT_LINK_STATE) 1270 link_state = (wIndex & 0xff00) >> 3; 1271 if (wValue == USB_PORT_FEAT_REMOTE_WAKE_MASK) 1272 wake_mask = wIndex & 0xff00; 1273 if (wValue == USB_PORT_FEAT_TEST) 1274 test_mode = (wIndex & 0xff00) >> 8; 1275 /* The MSB of wIndex is the U1/U2 timeout */ 1276 timeout = (wIndex & 0xff00) >> 8; 1277 wIndex &= 0xff; 1278 if (!wIndex || wIndex > max_ports) 1279 goto error; 1280 wIndex--; 1281 temp = readl(ports[wIndex]->addr); 1282 if (temp == ~(u32)0) { 1283 xhci_hc_died(xhci); 1284 retval = -ENODEV; 1285 break; 1286 } 1287 temp = xhci_port_state_to_neutral(temp); 1288 /* FIXME: What new port features do we need to support? */ 1289 switch (wValue) { 1290 case USB_PORT_FEAT_SUSPEND: 1291 temp = readl(ports[wIndex]->addr); 1292 if ((temp & PORT_PLS_MASK) != XDEV_U0) { 1293 /* Resume the port to U0 first */ 1294 xhci_set_link_state(xhci, ports[wIndex], 1295 XDEV_U0); 1296 spin_unlock_irqrestore(&xhci->lock, flags); 1297 msleep(10); 1298 spin_lock_irqsave(&xhci->lock, flags); 1299 } 1300 /* In spec software should not attempt to suspend 1301 * a port unless the port reports that it is in the 1302 * enabled (PED = ‘1’,PLS < ‘3’) state. 1303 */ 1304 temp = readl(ports[wIndex]->addr); 1305 if ((temp & PORT_PE) == 0 || (temp & PORT_RESET) 1306 || (temp & PORT_PLS_MASK) >= XDEV_U3) { 1307 xhci_warn(xhci, "USB core suspending port %d-%d not in U0/U1/U2\n", 1308 hcd->self.busnum, wIndex + 1); 1309 goto error; 1310 } 1311 1312 slot_id = xhci_find_slot_id_by_port(hcd, xhci, 1313 wIndex + 1); 1314 if (!slot_id) { 1315 xhci_warn(xhci, "slot_id is zero\n"); 1316 goto error; 1317 } 1318 /* unlock to execute stop endpoint commands */ 1319 spin_unlock_irqrestore(&xhci->lock, flags); 1320 xhci_stop_device(xhci, slot_id, 1); 1321 spin_lock_irqsave(&xhci->lock, flags); 1322 1323 xhci_set_link_state(xhci, ports[wIndex], XDEV_U3); 1324 1325 spin_unlock_irqrestore(&xhci->lock, flags); 1326 msleep(10); /* wait device to enter */ 1327 spin_lock_irqsave(&xhci->lock, flags); 1328 1329 temp = readl(ports[wIndex]->addr); 1330 bus_state->suspended_ports |= 1 << wIndex; 1331 break; 1332 case USB_PORT_FEAT_LINK_STATE: 1333 temp = readl(ports[wIndex]->addr); 1334 /* Disable port */ 1335 if (link_state == USB_SS_PORT_LS_SS_DISABLED) { 1336 xhci_dbg(xhci, "Disable port %d-%d\n", 1337 hcd->self.busnum, wIndex + 1); 1338 temp = xhci_port_state_to_neutral(temp); 1339 /* 1340 * Clear all change bits, so that we get a new 1341 * connection event. 1342 */ 1343 temp |= PORT_CSC | PORT_PEC | PORT_WRC | 1344 PORT_OCC | PORT_RC | PORT_PLC | 1345 PORT_CEC; 1346 writel(temp | PORT_PE, ports[wIndex]->addr); 1347 temp = readl(ports[wIndex]->addr); 1348 break; 1349 } 1350 1351 /* Put link in RxDetect (enable port) */ 1352 if (link_state == USB_SS_PORT_LS_RX_DETECT) { 1353 xhci_dbg(xhci, "Enable port %d-%d\n", 1354 hcd->self.busnum, wIndex + 1); 1355 xhci_set_link_state(xhci, ports[wIndex], 1356 link_state); 1357 temp = readl(ports[wIndex]->addr); 1358 break; 1359 } 1360 1361 /* 1362 * For xHCI 1.1 according to section 4.19.1.2.4.1 a 1363 * root hub port's transition to compliance mode upon 1364 * detecting LFPS timeout may be controlled by an 1365 * Compliance Transition Enabled (CTE) flag (not 1366 * software visible). This flag is set by writing 0xA 1367 * to PORTSC PLS field which will allow transition to 1368 * compliance mode the next time LFPS timeout is 1369 * encountered. A warm reset will clear it. 1370 * 1371 * The CTE flag is only supported if the HCCPARAMS2 CTC 1372 * flag is set, otherwise, the compliance substate is 1373 * automatically entered as on 1.0 and prior. 1374 */ 1375 if (link_state == USB_SS_PORT_LS_COMP_MOD) { 1376 if (!HCC2_CTC(xhci->hcc_params2)) { 1377 xhci_dbg(xhci, "CTC flag is 0, port already supports entering compliance mode\n"); 1378 break; 1379 } 1380 1381 if ((temp & PORT_CONNECT)) { 1382 xhci_warn(xhci, "Can't set compliance mode when port is connected\n"); 1383 goto error; 1384 } 1385 1386 xhci_dbg(xhci, "Enable compliance mode transition for port %d-%d\n", 1387 hcd->self.busnum, wIndex + 1); 1388 xhci_set_link_state(xhci, ports[wIndex], 1389 link_state); 1390 1391 temp = readl(ports[wIndex]->addr); 1392 break; 1393 } 1394 /* Port must be enabled */ 1395 if (!(temp & PORT_PE)) { 1396 retval = -ENODEV; 1397 break; 1398 } 1399 /* Can't set port link state above '3' (U3) */ 1400 if (link_state > USB_SS_PORT_LS_U3) { 1401 xhci_warn(xhci, "Cannot set port %d-%d link state %d\n", 1402 hcd->self.busnum, wIndex + 1, 1403 link_state); 1404 goto error; 1405 } 1406 1407 /* 1408 * set link to U0, steps depend on current link state. 1409 * U3: set link to U0 and wait for u3exit completion. 1410 * U1/U2: no PLC complete event, only set link to U0. 1411 * Resume/Recovery: device initiated U0, only wait for 1412 * completion 1413 */ 1414 if (link_state == USB_SS_PORT_LS_U0) { 1415 u32 pls = temp & PORT_PLS_MASK; 1416 bool wait_u0 = false; 1417 1418 /* already in U0 */ 1419 if (pls == XDEV_U0) 1420 break; 1421 if (pls == XDEV_U3 || 1422 pls == XDEV_RESUME || 1423 pls == XDEV_RECOVERY) { 1424 wait_u0 = true; 1425 reinit_completion(&bus_state->u3exit_done[wIndex]); 1426 } 1427 if (pls <= XDEV_U3) /* U1, U2, U3 */ 1428 xhci_set_link_state(xhci, ports[wIndex], 1429 USB_SS_PORT_LS_U0); 1430 if (!wait_u0) { 1431 if (pls > XDEV_U3) 1432 goto error; 1433 break; 1434 } 1435 spin_unlock_irqrestore(&xhci->lock, flags); 1436 if (!wait_for_completion_timeout(&bus_state->u3exit_done[wIndex], 1437 msecs_to_jiffies(100))) 1438 xhci_dbg(xhci, "missing U0 port change event for port %d-%d\n", 1439 hcd->self.busnum, wIndex + 1); 1440 spin_lock_irqsave(&xhci->lock, flags); 1441 temp = readl(ports[wIndex]->addr); 1442 break; 1443 } 1444 1445 if (link_state == USB_SS_PORT_LS_U3) { 1446 int retries = 16; 1447 slot_id = xhci_find_slot_id_by_port(hcd, xhci, 1448 wIndex + 1); 1449 if (slot_id) { 1450 /* unlock to execute stop endpoint 1451 * commands */ 1452 spin_unlock_irqrestore(&xhci->lock, 1453 flags); 1454 xhci_stop_device(xhci, slot_id, 1); 1455 spin_lock_irqsave(&xhci->lock, flags); 1456 } 1457 xhci_set_link_state(xhci, ports[wIndex], USB_SS_PORT_LS_U3); 1458 spin_unlock_irqrestore(&xhci->lock, flags); 1459 while (retries--) { 1460 usleep_range(4000, 8000); 1461 temp = readl(ports[wIndex]->addr); 1462 if ((temp & PORT_PLS_MASK) == XDEV_U3) 1463 break; 1464 } 1465 spin_lock_irqsave(&xhci->lock, flags); 1466 temp = readl(ports[wIndex]->addr); 1467 bus_state->suspended_ports |= 1 << wIndex; 1468 } 1469 break; 1470 case USB_PORT_FEAT_POWER: 1471 /* 1472 * Turn on ports, even if there isn't per-port switching. 1473 * HC will report connect events even before this is set. 1474 * However, hub_wq will ignore the roothub events until 1475 * the roothub is registered. 1476 */ 1477 xhci_set_port_power(xhci, hcd, wIndex, true, &flags); 1478 break; 1479 case USB_PORT_FEAT_RESET: 1480 temp = (temp | PORT_RESET); 1481 writel(temp, ports[wIndex]->addr); 1482 1483 temp = readl(ports[wIndex]->addr); 1484 xhci_dbg(xhci, "set port reset, actual port %d-%d status = 0x%x\n", 1485 hcd->self.busnum, wIndex + 1, temp); 1486 break; 1487 case USB_PORT_FEAT_REMOTE_WAKE_MASK: 1488 xhci_set_remote_wake_mask(xhci, ports[wIndex], 1489 wake_mask); 1490 temp = readl(ports[wIndex]->addr); 1491 xhci_dbg(xhci, "set port remote wake mask, actual port %d-%d status = 0x%x\n", 1492 hcd->self.busnum, wIndex + 1, temp); 1493 break; 1494 case USB_PORT_FEAT_BH_PORT_RESET: 1495 temp |= PORT_WR; 1496 writel(temp, ports[wIndex]->addr); 1497 temp = readl(ports[wIndex]->addr); 1498 break; 1499 case USB_PORT_FEAT_U1_TIMEOUT: 1500 if (hcd->speed < HCD_USB3) 1501 goto error; 1502 temp = readl(ports[wIndex]->addr + PORTPMSC); 1503 temp &= ~PORT_U1_TIMEOUT_MASK; 1504 temp |= PORT_U1_TIMEOUT(timeout); 1505 writel(temp, ports[wIndex]->addr + PORTPMSC); 1506 break; 1507 case USB_PORT_FEAT_U2_TIMEOUT: 1508 if (hcd->speed < HCD_USB3) 1509 goto error; 1510 temp = readl(ports[wIndex]->addr + PORTPMSC); 1511 temp &= ~PORT_U2_TIMEOUT_MASK; 1512 temp |= PORT_U2_TIMEOUT(timeout); 1513 writel(temp, ports[wIndex]->addr + PORTPMSC); 1514 break; 1515 case USB_PORT_FEAT_TEST: 1516 /* 4.19.6 Port Test Modes (USB2 Test Mode) */ 1517 if (hcd->speed != HCD_USB2) 1518 goto error; 1519 if (test_mode > USB_TEST_FORCE_ENABLE || 1520 test_mode < USB_TEST_J) 1521 goto error; 1522 retval = xhci_enter_test_mode(xhci, test_mode, wIndex, 1523 &flags); 1524 break; 1525 default: 1526 goto error; 1527 } 1528 /* unblock any posted writes */ 1529 temp = readl(ports[wIndex]->addr); 1530 break; 1531 case ClearPortFeature: 1532 if (!wIndex || wIndex > max_ports) 1533 goto error; 1534 wIndex--; 1535 temp = readl(ports[wIndex]->addr); 1536 if (temp == ~(u32)0) { 1537 xhci_hc_died(xhci); 1538 retval = -ENODEV; 1539 break; 1540 } 1541 /* FIXME: What new port features do we need to support? */ 1542 temp = xhci_port_state_to_neutral(temp); 1543 switch (wValue) { 1544 case USB_PORT_FEAT_SUSPEND: 1545 temp = readl(ports[wIndex]->addr); 1546 xhci_dbg(xhci, "clear USB_PORT_FEAT_SUSPEND\n"); 1547 xhci_dbg(xhci, "PORTSC %04x\n", temp); 1548 if (temp & PORT_RESET) 1549 goto error; 1550 if ((temp & PORT_PLS_MASK) == XDEV_U3) { 1551 if ((temp & PORT_PE) == 0) 1552 goto error; 1553 1554 set_bit(wIndex, &bus_state->resuming_ports); 1555 usb_hcd_start_port_resume(&hcd->self, wIndex); 1556 xhci_set_link_state(xhci, ports[wIndex], 1557 XDEV_RESUME); 1558 spin_unlock_irqrestore(&xhci->lock, flags); 1559 msleep(USB_RESUME_TIMEOUT); 1560 spin_lock_irqsave(&xhci->lock, flags); 1561 xhci_set_link_state(xhci, ports[wIndex], 1562 XDEV_U0); 1563 clear_bit(wIndex, &bus_state->resuming_ports); 1564 usb_hcd_end_port_resume(&hcd->self, wIndex); 1565 } 1566 bus_state->port_c_suspend |= 1 << wIndex; 1567 1568 slot_id = xhci_find_slot_id_by_port(hcd, xhci, 1569 wIndex + 1); 1570 if (!slot_id) { 1571 xhci_dbg(xhci, "slot_id is zero\n"); 1572 goto error; 1573 } 1574 xhci_ring_device(xhci, slot_id); 1575 break; 1576 case USB_PORT_FEAT_C_SUSPEND: 1577 bus_state->port_c_suspend &= ~(1 << wIndex); 1578 fallthrough; 1579 case USB_PORT_FEAT_C_RESET: 1580 case USB_PORT_FEAT_C_BH_PORT_RESET: 1581 case USB_PORT_FEAT_C_CONNECTION: 1582 case USB_PORT_FEAT_C_OVER_CURRENT: 1583 case USB_PORT_FEAT_C_ENABLE: 1584 case USB_PORT_FEAT_C_PORT_LINK_STATE: 1585 case USB_PORT_FEAT_C_PORT_CONFIG_ERROR: 1586 xhci_clear_port_change_bit(xhci, wValue, wIndex, 1587 ports[wIndex]->addr, temp); 1588 break; 1589 case USB_PORT_FEAT_ENABLE: 1590 xhci_disable_port(hcd, xhci, wIndex, 1591 ports[wIndex]->addr, temp); 1592 break; 1593 case USB_PORT_FEAT_POWER: 1594 xhci_set_port_power(xhci, hcd, wIndex, false, &flags); 1595 break; 1596 case USB_PORT_FEAT_TEST: 1597 retval = xhci_exit_test_mode(xhci); 1598 break; 1599 default: 1600 goto error; 1601 } 1602 break; 1603 default: 1604 error: 1605 /* "stall" on error */ 1606 retval = -EPIPE; 1607 } 1608 spin_unlock_irqrestore(&xhci->lock, flags); 1609 return retval; 1610 } 1611 1612 /* 1613 * Returns 0 if the status hasn't changed, or the number of bytes in buf. 1614 * Ports are 0-indexed from the HCD point of view, 1615 * and 1-indexed from the USB core pointer of view. 1616 * 1617 * Note that the status change bits will be cleared as soon as a port status 1618 * change event is generated, so we use the saved status from that event. 1619 */ 1620 int xhci_hub_status_data(struct usb_hcd *hcd, char *buf) 1621 { 1622 unsigned long flags; 1623 u32 temp, status; 1624 u32 mask; 1625 int i, retval; 1626 struct xhci_hcd *xhci = hcd_to_xhci(hcd); 1627 int max_ports; 1628 struct xhci_bus_state *bus_state; 1629 bool reset_change = false; 1630 struct xhci_hub *rhub; 1631 struct xhci_port **ports; 1632 1633 rhub = xhci_get_rhub(hcd); 1634 ports = rhub->ports; 1635 max_ports = rhub->num_ports; 1636 bus_state = &rhub->bus_state; 1637 1638 /* Initial status is no changes */ 1639 retval = (max_ports + 8) / 8; 1640 memset(buf, 0, retval); 1641 1642 /* 1643 * Inform the usbcore about resume-in-progress by returning 1644 * a non-zero value even if there are no status changes. 1645 */ 1646 spin_lock_irqsave(&xhci->lock, flags); 1647 1648 status = bus_state->resuming_ports; 1649 1650 mask = PORT_CSC | PORT_PEC | PORT_OCC | PORT_PLC | PORT_WRC | PORT_CEC; 1651 1652 /* For each port, did anything change? If so, set that bit in buf. */ 1653 for (i = 0; i < max_ports; i++) { 1654 temp = readl(ports[i]->addr); 1655 if (temp == ~(u32)0) { 1656 xhci_hc_died(xhci); 1657 retval = -ENODEV; 1658 break; 1659 } 1660 trace_xhci_hub_status_data(i, temp); 1661 1662 if ((temp & mask) != 0 || 1663 (bus_state->port_c_suspend & 1 << i) || 1664 (bus_state->resume_done[i] && time_after_eq( 1665 jiffies, bus_state->resume_done[i]))) { 1666 buf[(i + 1) / 8] |= 1 << (i + 1) % 8; 1667 status = 1; 1668 } 1669 if ((temp & PORT_RC)) 1670 reset_change = true; 1671 if (temp & PORT_OC) 1672 status = 1; 1673 } 1674 if (!status && !reset_change) { 1675 xhci_dbg(xhci, "%s: stopping usb%d port polling\n", 1676 __func__, hcd->self.busnum); 1677 clear_bit(HCD_FLAG_POLL_RH, &hcd->flags); 1678 } 1679 spin_unlock_irqrestore(&xhci->lock, flags); 1680 return status ? retval : 0; 1681 } 1682 1683 #ifdef CONFIG_PM 1684 1685 int xhci_bus_suspend(struct usb_hcd *hcd) 1686 { 1687 struct xhci_hcd *xhci = hcd_to_xhci(hcd); 1688 int max_ports, port_index; 1689 struct xhci_bus_state *bus_state; 1690 unsigned long flags; 1691 struct xhci_hub *rhub; 1692 struct xhci_port **ports; 1693 u32 portsc_buf[USB_MAXCHILDREN]; 1694 bool wake_enabled; 1695 1696 rhub = xhci_get_rhub(hcd); 1697 ports = rhub->ports; 1698 max_ports = rhub->num_ports; 1699 bus_state = &rhub->bus_state; 1700 wake_enabled = hcd->self.root_hub->do_remote_wakeup; 1701 1702 spin_lock_irqsave(&xhci->lock, flags); 1703 1704 if (wake_enabled) { 1705 if (bus_state->resuming_ports || /* USB2 */ 1706 bus_state->port_remote_wakeup) { /* USB3 */ 1707 spin_unlock_irqrestore(&xhci->lock, flags); 1708 xhci_dbg(xhci, "usb%d bus suspend to fail because a port is resuming\n", 1709 hcd->self.busnum); 1710 return -EBUSY; 1711 } 1712 } 1713 /* 1714 * Prepare ports for suspend, but don't write anything before all ports 1715 * are checked and we know bus suspend can proceed 1716 */ 1717 bus_state->bus_suspended = 0; 1718 port_index = max_ports; 1719 while (port_index--) { 1720 u32 t1, t2; 1721 int retries = 10; 1722 retry: 1723 t1 = readl(ports[port_index]->addr); 1724 t2 = xhci_port_state_to_neutral(t1); 1725 portsc_buf[port_index] = 0; 1726 1727 /* 1728 * Give a USB3 port in link training time to finish, but don't 1729 * prevent suspend as port might be stuck 1730 */ 1731 if ((hcd->speed >= HCD_USB3) && retries-- && 1732 (t1 & PORT_PLS_MASK) == XDEV_POLLING) { 1733 spin_unlock_irqrestore(&xhci->lock, flags); 1734 msleep(XHCI_PORT_POLLING_LFPS_TIME); 1735 spin_lock_irqsave(&xhci->lock, flags); 1736 xhci_dbg(xhci, "port %d-%d polling in bus suspend, waiting\n", 1737 hcd->self.busnum, port_index + 1); 1738 goto retry; 1739 } 1740 /* bail out if port detected a over-current condition */ 1741 if (t1 & PORT_OC) { 1742 bus_state->bus_suspended = 0; 1743 spin_unlock_irqrestore(&xhci->lock, flags); 1744 xhci_dbg(xhci, "Bus suspend bailout, port over-current detected\n"); 1745 return -EBUSY; 1746 } 1747 /* suspend ports in U0, or bail out for new connect changes */ 1748 if ((t1 & PORT_PE) && (t1 & PORT_PLS_MASK) == XDEV_U0) { 1749 if ((t1 & PORT_CSC) && wake_enabled) { 1750 bus_state->bus_suspended = 0; 1751 spin_unlock_irqrestore(&xhci->lock, flags); 1752 xhci_dbg(xhci, "Bus suspend bailout, port connect change\n"); 1753 return -EBUSY; 1754 } 1755 xhci_dbg(xhci, "port %d-%d not suspended\n", 1756 hcd->self.busnum, port_index + 1); 1757 t2 &= ~PORT_PLS_MASK; 1758 t2 |= PORT_LINK_STROBE | XDEV_U3; 1759 set_bit(port_index, &bus_state->bus_suspended); 1760 } 1761 /* USB core sets remote wake mask for USB 3.0 hubs, 1762 * including the USB 3.0 roothub, but only if CONFIG_PM 1763 * is enabled, so also enable remote wake here. 1764 */ 1765 if (wake_enabled) { 1766 if (t1 & PORT_CONNECT) { 1767 t2 |= PORT_WKOC_E | PORT_WKDISC_E; 1768 t2 &= ~PORT_WKCONN_E; 1769 } else { 1770 t2 |= PORT_WKOC_E | PORT_WKCONN_E; 1771 t2 &= ~PORT_WKDISC_E; 1772 } 1773 1774 if ((xhci->quirks & XHCI_U2_DISABLE_WAKE) && 1775 (hcd->speed < HCD_USB3)) { 1776 if (usb_amd_pt_check_port(hcd->self.controller, 1777 port_index)) 1778 t2 &= ~PORT_WAKE_BITS; 1779 } 1780 } else 1781 t2 &= ~PORT_WAKE_BITS; 1782 1783 t1 = xhci_port_state_to_neutral(t1); 1784 if (t1 != t2) 1785 portsc_buf[port_index] = t2; 1786 } 1787 1788 /* write port settings, stopping and suspending ports if needed */ 1789 port_index = max_ports; 1790 while (port_index--) { 1791 if (!portsc_buf[port_index]) 1792 continue; 1793 if (test_bit(port_index, &bus_state->bus_suspended)) { 1794 int slot_id; 1795 1796 slot_id = xhci_find_slot_id_by_port(hcd, xhci, 1797 port_index + 1); 1798 if (slot_id) { 1799 spin_unlock_irqrestore(&xhci->lock, flags); 1800 xhci_stop_device(xhci, slot_id, 1); 1801 spin_lock_irqsave(&xhci->lock, flags); 1802 } 1803 } 1804 writel(portsc_buf[port_index], ports[port_index]->addr); 1805 } 1806 hcd->state = HC_STATE_SUSPENDED; 1807 bus_state->next_statechange = jiffies + msecs_to_jiffies(10); 1808 spin_unlock_irqrestore(&xhci->lock, flags); 1809 1810 if (bus_state->bus_suspended) 1811 usleep_range(5000, 10000); 1812 1813 return 0; 1814 } 1815 1816 /* 1817 * Workaround for missing Cold Attach Status (CAS) if device re-plugged in S3. 1818 * warm reset a USB3 device stuck in polling or compliance mode after resume. 1819 * See Intel 100/c230 series PCH specification update Doc #332692-006 Errata #8 1820 */ 1821 static bool xhci_port_missing_cas_quirk(struct xhci_port *port) 1822 { 1823 u32 portsc; 1824 1825 portsc = readl(port->addr); 1826 1827 /* if any of these are set we are not stuck */ 1828 if (portsc & (PORT_CONNECT | PORT_CAS)) 1829 return false; 1830 1831 if (((portsc & PORT_PLS_MASK) != XDEV_POLLING) && 1832 ((portsc & PORT_PLS_MASK) != XDEV_COMP_MODE)) 1833 return false; 1834 1835 /* clear wakeup/change bits, and do a warm port reset */ 1836 portsc &= ~(PORT_RWC_BITS | PORT_CEC | PORT_WAKE_BITS); 1837 portsc |= PORT_WR; 1838 writel(portsc, port->addr); 1839 /* flush write */ 1840 readl(port->addr); 1841 return true; 1842 } 1843 1844 int xhci_bus_resume(struct usb_hcd *hcd) 1845 { 1846 struct xhci_hcd *xhci = hcd_to_xhci(hcd); 1847 struct xhci_bus_state *bus_state; 1848 unsigned long flags; 1849 int max_ports, port_index; 1850 int slot_id; 1851 int sret; 1852 u32 next_state; 1853 u32 temp, portsc; 1854 struct xhci_hub *rhub; 1855 struct xhci_port **ports; 1856 1857 rhub = xhci_get_rhub(hcd); 1858 ports = rhub->ports; 1859 max_ports = rhub->num_ports; 1860 bus_state = &rhub->bus_state; 1861 1862 if (time_before(jiffies, bus_state->next_statechange)) 1863 msleep(5); 1864 1865 spin_lock_irqsave(&xhci->lock, flags); 1866 if (!HCD_HW_ACCESSIBLE(hcd)) { 1867 spin_unlock_irqrestore(&xhci->lock, flags); 1868 return -ESHUTDOWN; 1869 } 1870 1871 /* delay the irqs */ 1872 temp = readl(&xhci->op_regs->command); 1873 temp &= ~CMD_EIE; 1874 writel(temp, &xhci->op_regs->command); 1875 1876 /* bus specific resume for ports we suspended at bus_suspend */ 1877 if (hcd->speed >= HCD_USB3) 1878 next_state = XDEV_U0; 1879 else 1880 next_state = XDEV_RESUME; 1881 1882 port_index = max_ports; 1883 while (port_index--) { 1884 portsc = readl(ports[port_index]->addr); 1885 1886 /* warm reset CAS limited ports stuck in polling/compliance */ 1887 if ((xhci->quirks & XHCI_MISSING_CAS) && 1888 (hcd->speed >= HCD_USB3) && 1889 xhci_port_missing_cas_quirk(ports[port_index])) { 1890 xhci_dbg(xhci, "reset stuck port %d-%d\n", 1891 hcd->self.busnum, port_index + 1); 1892 clear_bit(port_index, &bus_state->bus_suspended); 1893 continue; 1894 } 1895 /* resume if we suspended the link, and it is still suspended */ 1896 if (test_bit(port_index, &bus_state->bus_suspended)) 1897 switch (portsc & PORT_PLS_MASK) { 1898 case XDEV_U3: 1899 portsc = xhci_port_state_to_neutral(portsc); 1900 portsc &= ~PORT_PLS_MASK; 1901 portsc |= PORT_LINK_STROBE | next_state; 1902 break; 1903 case XDEV_RESUME: 1904 /* resume already initiated */ 1905 break; 1906 default: 1907 /* not in a resumeable state, ignore it */ 1908 clear_bit(port_index, 1909 &bus_state->bus_suspended); 1910 break; 1911 } 1912 /* disable wake for all ports, write new link state if needed */ 1913 portsc &= ~(PORT_RWC_BITS | PORT_CEC | PORT_WAKE_BITS); 1914 writel(portsc, ports[port_index]->addr); 1915 } 1916 1917 /* USB2 specific resume signaling delay and U0 link state transition */ 1918 if (hcd->speed < HCD_USB3) { 1919 if (bus_state->bus_suspended) { 1920 spin_unlock_irqrestore(&xhci->lock, flags); 1921 msleep(USB_RESUME_TIMEOUT); 1922 spin_lock_irqsave(&xhci->lock, flags); 1923 } 1924 for_each_set_bit(port_index, &bus_state->bus_suspended, 1925 BITS_PER_LONG) { 1926 /* Clear PLC to poll it later for U0 transition */ 1927 xhci_test_and_clear_bit(xhci, ports[port_index], 1928 PORT_PLC); 1929 xhci_set_link_state(xhci, ports[port_index], XDEV_U0); 1930 } 1931 } 1932 1933 /* poll for U0 link state complete, both USB2 and USB3 */ 1934 for_each_set_bit(port_index, &bus_state->bus_suspended, BITS_PER_LONG) { 1935 sret = xhci_handshake(ports[port_index]->addr, PORT_PLC, 1936 PORT_PLC, 10 * 1000); 1937 if (sret) { 1938 xhci_warn(xhci, "port %d-%d resume PLC timeout\n", 1939 hcd->self.busnum, port_index + 1); 1940 continue; 1941 } 1942 xhci_test_and_clear_bit(xhci, ports[port_index], PORT_PLC); 1943 slot_id = xhci_find_slot_id_by_port(hcd, xhci, port_index + 1); 1944 if (slot_id) 1945 xhci_ring_device(xhci, slot_id); 1946 } 1947 (void) readl(&xhci->op_regs->command); 1948 1949 bus_state->next_statechange = jiffies + msecs_to_jiffies(5); 1950 /* re-enable irqs */ 1951 temp = readl(&xhci->op_regs->command); 1952 temp |= CMD_EIE; 1953 writel(temp, &xhci->op_regs->command); 1954 temp = readl(&xhci->op_regs->command); 1955 1956 spin_unlock_irqrestore(&xhci->lock, flags); 1957 return 0; 1958 } 1959 1960 unsigned long xhci_get_resuming_ports(struct usb_hcd *hcd) 1961 { 1962 struct xhci_hub *rhub = xhci_get_rhub(hcd); 1963 1964 /* USB3 port wakeups are reported via usb_wakeup_notification() */ 1965 return rhub->bus_state.resuming_ports; /* USB2 ports only */ 1966 } 1967 1968 #endif /* CONFIG_PM */ 1969