1 // SPDX-License-Identifier: GPL-1.0+ 2 /* 3 * OHCI HCD (Host Controller Driver) for USB. 4 * 5 * (C) Copyright 1999 Roman Weissgaerber <weissg@vienna.at> 6 * (C) Copyright 2000-2002 David Brownell <dbrownell@users.sourceforge.net> 7 * (C) Copyright 2002 Hewlett-Packard Company 8 * 9 * Bus Glue for pxa27x 10 * 11 * Written by Christopher Hoover <ch@hpl.hp.com> 12 * Based on fragments of previous driver by Russell King et al. 13 * 14 * Modified for LH7A404 from ohci-sa1111.c 15 * by Durgesh Pattamatta <pattamattad@sharpsec.com> 16 * 17 * Modified for pxa27x from ohci-lh7a404.c 18 * by Nick Bane <nick@cecomputing.co.uk> 26-8-2004 19 * 20 * This file is licenced under the GPL. 21 */ 22 23 #include <linux/clk.h> 24 #include <linux/device.h> 25 #include <linux/dma-mapping.h> 26 #include <linux/io.h> 27 #include <linux/kernel.h> 28 #include <linux/module.h> 29 #include <linux/of_platform.h> 30 #include <linux/of_gpio.h> 31 #include <linux/platform_data/usb-ohci-pxa27x.h> 32 #include <linux/platform_data/usb-pxa3xx-ulpi.h> 33 #include <linux/platform_device.h> 34 #include <linux/regulator/consumer.h> 35 #include <linux/signal.h> 36 #include <linux/usb.h> 37 #include <linux/usb/hcd.h> 38 #include <linux/usb/otg.h> 39 40 #include <mach/hardware.h> 41 42 #include "ohci.h" 43 44 #define DRIVER_DESC "OHCI PXA27x/PXA3x driver" 45 46 /* 47 * UHC: USB Host Controller (OHCI-like) register definitions 48 */ 49 #define UHCREV (0x0000) /* UHC HCI Spec Revision */ 50 #define UHCHCON (0x0004) /* UHC Host Control Register */ 51 #define UHCCOMS (0x0008) /* UHC Command Status Register */ 52 #define UHCINTS (0x000C) /* UHC Interrupt Status Register */ 53 #define UHCINTE (0x0010) /* UHC Interrupt Enable */ 54 #define UHCINTD (0x0014) /* UHC Interrupt Disable */ 55 #define UHCHCCA (0x0018) /* UHC Host Controller Comm. Area */ 56 #define UHCPCED (0x001C) /* UHC Period Current Endpt Descr */ 57 #define UHCCHED (0x0020) /* UHC Control Head Endpt Descr */ 58 #define UHCCCED (0x0024) /* UHC Control Current Endpt Descr */ 59 #define UHCBHED (0x0028) /* UHC Bulk Head Endpt Descr */ 60 #define UHCBCED (0x002C) /* UHC Bulk Current Endpt Descr */ 61 #define UHCDHEAD (0x0030) /* UHC Done Head */ 62 #define UHCFMI (0x0034) /* UHC Frame Interval */ 63 #define UHCFMR (0x0038) /* UHC Frame Remaining */ 64 #define UHCFMN (0x003C) /* UHC Frame Number */ 65 #define UHCPERS (0x0040) /* UHC Periodic Start */ 66 #define UHCLS (0x0044) /* UHC Low Speed Threshold */ 67 68 #define UHCRHDA (0x0048) /* UHC Root Hub Descriptor A */ 69 #define UHCRHDA_NOCP (1 << 12) /* No over current protection */ 70 #define UHCRHDA_OCPM (1 << 11) /* Over Current Protection Mode */ 71 #define UHCRHDA_POTPGT(x) \ 72 (((x) & 0xff) << 24) /* Power On To Power Good Time */ 73 74 #define UHCRHDB (0x004C) /* UHC Root Hub Descriptor B */ 75 #define UHCRHS (0x0050) /* UHC Root Hub Status */ 76 #define UHCRHPS1 (0x0054) /* UHC Root Hub Port 1 Status */ 77 #define UHCRHPS2 (0x0058) /* UHC Root Hub Port 2 Status */ 78 #define UHCRHPS3 (0x005C) /* UHC Root Hub Port 3 Status */ 79 80 #define UHCSTAT (0x0060) /* UHC Status Register */ 81 #define UHCSTAT_UPS3 (1 << 16) /* USB Power Sense Port3 */ 82 #define UHCSTAT_SBMAI (1 << 15) /* System Bus Master Abort Interrupt*/ 83 #define UHCSTAT_SBTAI (1 << 14) /* System Bus Target Abort Interrupt*/ 84 #define UHCSTAT_UPRI (1 << 13) /* USB Port Resume Interrupt */ 85 #define UHCSTAT_UPS2 (1 << 12) /* USB Power Sense Port 2 */ 86 #define UHCSTAT_UPS1 (1 << 11) /* USB Power Sense Port 1 */ 87 #define UHCSTAT_HTA (1 << 10) /* HCI Target Abort */ 88 #define UHCSTAT_HBA (1 << 8) /* HCI Buffer Active */ 89 #define UHCSTAT_RWUE (1 << 7) /* HCI Remote Wake Up Event */ 90 91 #define UHCHR (0x0064) /* UHC Reset Register */ 92 #define UHCHR_SSEP3 (1 << 11) /* Sleep Standby Enable for Port3 */ 93 #define UHCHR_SSEP2 (1 << 10) /* Sleep Standby Enable for Port2 */ 94 #define UHCHR_SSEP1 (1 << 9) /* Sleep Standby Enable for Port1 */ 95 #define UHCHR_PCPL (1 << 7) /* Power control polarity low */ 96 #define UHCHR_PSPL (1 << 6) /* Power sense polarity low */ 97 #define UHCHR_SSE (1 << 5) /* Sleep Standby Enable */ 98 #define UHCHR_UIT (1 << 4) /* USB Interrupt Test */ 99 #define UHCHR_SSDC (1 << 3) /* Simulation Scale Down Clock */ 100 #define UHCHR_CGR (1 << 2) /* Clock Generation Reset */ 101 #define UHCHR_FHR (1 << 1) /* Force Host Controller Reset */ 102 #define UHCHR_FSBIR (1 << 0) /* Force System Bus Iface Reset */ 103 104 #define UHCHIE (0x0068) /* UHC Interrupt Enable Register*/ 105 #define UHCHIE_UPS3IE (1 << 14) /* Power Sense Port3 IntEn */ 106 #define UHCHIE_UPRIE (1 << 13) /* Port Resume IntEn */ 107 #define UHCHIE_UPS2IE (1 << 12) /* Power Sense Port2 IntEn */ 108 #define UHCHIE_UPS1IE (1 << 11) /* Power Sense Port1 IntEn */ 109 #define UHCHIE_TAIE (1 << 10) /* HCI Interface Transfer Abort 110 Interrupt Enable*/ 111 #define UHCHIE_HBAIE (1 << 8) /* HCI Buffer Active IntEn */ 112 #define UHCHIE_RWIE (1 << 7) /* Remote Wake-up IntEn */ 113 114 #define UHCHIT (0x006C) /* UHC Interrupt Test register */ 115 116 #define PXA_UHC_MAX_PORTNUM 3 117 118 static const char hcd_name[] = "ohci-pxa27x"; 119 120 static struct hc_driver __read_mostly ohci_pxa27x_hc_driver; 121 122 struct pxa27x_ohci { 123 struct clk *clk; 124 void __iomem *mmio_base; 125 struct regulator *vbus[3]; 126 bool vbus_enabled[3]; 127 }; 128 129 #define to_pxa27x_ohci(hcd) (struct pxa27x_ohci *)(hcd_to_ohci(hcd)->priv) 130 131 /* 132 PMM_NPS_MODE -- PMM Non-power switching mode 133 Ports are powered continuously. 134 135 PMM_GLOBAL_MODE -- PMM global switching mode 136 All ports are powered at the same time. 137 138 PMM_PERPORT_MODE -- PMM per port switching mode 139 Ports are powered individually. 140 */ 141 static int pxa27x_ohci_select_pmm(struct pxa27x_ohci *pxa_ohci, int mode) 142 { 143 uint32_t uhcrhda = __raw_readl(pxa_ohci->mmio_base + UHCRHDA); 144 uint32_t uhcrhdb = __raw_readl(pxa_ohci->mmio_base + UHCRHDB); 145 146 switch (mode) { 147 case PMM_NPS_MODE: 148 uhcrhda |= RH_A_NPS; 149 break; 150 case PMM_GLOBAL_MODE: 151 uhcrhda &= ~(RH_A_NPS | RH_A_PSM); 152 break; 153 case PMM_PERPORT_MODE: 154 uhcrhda &= ~(RH_A_NPS); 155 uhcrhda |= RH_A_PSM; 156 157 /* Set port power control mask bits, only 3 ports. */ 158 uhcrhdb |= (0x7<<17); 159 break; 160 default: 161 printk( KERN_ERR 162 "Invalid mode %d, set to non-power switch mode.\n", 163 mode ); 164 165 uhcrhda |= RH_A_NPS; 166 } 167 168 __raw_writel(uhcrhda, pxa_ohci->mmio_base + UHCRHDA); 169 __raw_writel(uhcrhdb, pxa_ohci->mmio_base + UHCRHDB); 170 return 0; 171 } 172 173 static int pxa27x_ohci_set_vbus_power(struct pxa27x_ohci *pxa_ohci, 174 unsigned int port, bool enable) 175 { 176 struct regulator *vbus = pxa_ohci->vbus[port]; 177 int ret = 0; 178 179 if (IS_ERR_OR_NULL(vbus)) 180 return 0; 181 182 if (enable && !pxa_ohci->vbus_enabled[port]) 183 ret = regulator_enable(vbus); 184 else if (!enable && pxa_ohci->vbus_enabled[port]) 185 ret = regulator_disable(vbus); 186 187 if (ret < 0) 188 return ret; 189 190 pxa_ohci->vbus_enabled[port] = enable; 191 192 return 0; 193 } 194 195 static int pxa27x_ohci_hub_control(struct usb_hcd *hcd, u16 typeReq, u16 wValue, 196 u16 wIndex, char *buf, u16 wLength) 197 { 198 struct pxa27x_ohci *pxa_ohci = to_pxa27x_ohci(hcd); 199 int ret; 200 201 switch (typeReq) { 202 case SetPortFeature: 203 case ClearPortFeature: 204 if (!wIndex || wIndex > 3) 205 return -EPIPE; 206 207 if (wValue != USB_PORT_FEAT_POWER) 208 break; 209 210 ret = pxa27x_ohci_set_vbus_power(pxa_ohci, wIndex - 1, 211 typeReq == SetPortFeature); 212 if (ret) 213 return ret; 214 break; 215 } 216 217 return ohci_hub_control(hcd, typeReq, wValue, wIndex, buf, wLength); 218 } 219 /*-------------------------------------------------------------------------*/ 220 221 static inline void pxa27x_setup_hc(struct pxa27x_ohci *pxa_ohci, 222 struct pxaohci_platform_data *inf) 223 { 224 uint32_t uhchr = __raw_readl(pxa_ohci->mmio_base + UHCHR); 225 uint32_t uhcrhda = __raw_readl(pxa_ohci->mmio_base + UHCRHDA); 226 227 if (inf->flags & ENABLE_PORT1) 228 uhchr &= ~UHCHR_SSEP1; 229 230 if (inf->flags & ENABLE_PORT2) 231 uhchr &= ~UHCHR_SSEP2; 232 233 if (inf->flags & ENABLE_PORT3) 234 uhchr &= ~UHCHR_SSEP3; 235 236 if (inf->flags & POWER_CONTROL_LOW) 237 uhchr |= UHCHR_PCPL; 238 239 if (inf->flags & POWER_SENSE_LOW) 240 uhchr |= UHCHR_PSPL; 241 242 if (inf->flags & NO_OC_PROTECTION) 243 uhcrhda |= UHCRHDA_NOCP; 244 else 245 uhcrhda &= ~UHCRHDA_NOCP; 246 247 if (inf->flags & OC_MODE_PERPORT) 248 uhcrhda |= UHCRHDA_OCPM; 249 else 250 uhcrhda &= ~UHCRHDA_OCPM; 251 252 if (inf->power_on_delay) { 253 uhcrhda &= ~UHCRHDA_POTPGT(0xff); 254 uhcrhda |= UHCRHDA_POTPGT(inf->power_on_delay / 2); 255 } 256 257 __raw_writel(uhchr, pxa_ohci->mmio_base + UHCHR); 258 __raw_writel(uhcrhda, pxa_ohci->mmio_base + UHCRHDA); 259 } 260 261 static inline void pxa27x_reset_hc(struct pxa27x_ohci *pxa_ohci) 262 { 263 uint32_t uhchr = __raw_readl(pxa_ohci->mmio_base + UHCHR); 264 265 __raw_writel(uhchr | UHCHR_FHR, pxa_ohci->mmio_base + UHCHR); 266 udelay(11); 267 __raw_writel(uhchr & ~UHCHR_FHR, pxa_ohci->mmio_base + UHCHR); 268 } 269 270 #ifdef CONFIG_PXA27x 271 extern void pxa27x_clear_otgph(void); 272 #else 273 #define pxa27x_clear_otgph() do {} while (0) 274 #endif 275 276 static int pxa27x_start_hc(struct pxa27x_ohci *pxa_ohci, struct device *dev) 277 { 278 int retval; 279 struct pxaohci_platform_data *inf; 280 uint32_t uhchr; 281 struct usb_hcd *hcd = dev_get_drvdata(dev); 282 283 inf = dev_get_platdata(dev); 284 285 retval = clk_prepare_enable(pxa_ohci->clk); 286 if (retval) 287 return retval; 288 289 pxa27x_reset_hc(pxa_ohci); 290 291 uhchr = __raw_readl(pxa_ohci->mmio_base + UHCHR) | UHCHR_FSBIR; 292 __raw_writel(uhchr, pxa_ohci->mmio_base + UHCHR); 293 294 while (__raw_readl(pxa_ohci->mmio_base + UHCHR) & UHCHR_FSBIR) 295 cpu_relax(); 296 297 pxa27x_setup_hc(pxa_ohci, inf); 298 299 if (inf->init) 300 retval = inf->init(dev); 301 302 if (retval < 0) { 303 clk_disable_unprepare(pxa_ohci->clk); 304 return retval; 305 } 306 307 if (cpu_is_pxa3xx()) 308 pxa3xx_u2d_start_hc(&hcd->self); 309 310 uhchr = __raw_readl(pxa_ohci->mmio_base + UHCHR) & ~UHCHR_SSE; 311 __raw_writel(uhchr, pxa_ohci->mmio_base + UHCHR); 312 __raw_writel(UHCHIE_UPRIE | UHCHIE_RWIE, pxa_ohci->mmio_base + UHCHIE); 313 314 /* Clear any OTG Pin Hold */ 315 pxa27x_clear_otgph(); 316 return 0; 317 } 318 319 static void pxa27x_stop_hc(struct pxa27x_ohci *pxa_ohci, struct device *dev) 320 { 321 struct pxaohci_platform_data *inf; 322 struct usb_hcd *hcd = dev_get_drvdata(dev); 323 uint32_t uhccoms; 324 325 inf = dev_get_platdata(dev); 326 327 if (cpu_is_pxa3xx()) 328 pxa3xx_u2d_stop_hc(&hcd->self); 329 330 if (inf->exit) 331 inf->exit(dev); 332 333 pxa27x_reset_hc(pxa_ohci); 334 335 /* Host Controller Reset */ 336 uhccoms = __raw_readl(pxa_ohci->mmio_base + UHCCOMS) | 0x01; 337 __raw_writel(uhccoms, pxa_ohci->mmio_base + UHCCOMS); 338 udelay(10); 339 340 clk_disable_unprepare(pxa_ohci->clk); 341 } 342 343 #ifdef CONFIG_OF 344 static const struct of_device_id pxa_ohci_dt_ids[] = { 345 { .compatible = "marvell,pxa-ohci" }, 346 { } 347 }; 348 349 MODULE_DEVICE_TABLE(of, pxa_ohci_dt_ids); 350 351 static int ohci_pxa_of_init(struct platform_device *pdev) 352 { 353 struct device_node *np = pdev->dev.of_node; 354 struct pxaohci_platform_data *pdata; 355 u32 tmp; 356 int ret; 357 358 if (!np) 359 return 0; 360 361 /* Right now device-tree probed devices don't get dma_mask set. 362 * Since shared usb code relies on it, set it here for now. 363 * Once we have dma capability bindings this can go away. 364 */ 365 ret = dma_coerce_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(32)); 366 if (ret) 367 return ret; 368 369 pdata = devm_kzalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL); 370 if (!pdata) 371 return -ENOMEM; 372 373 if (of_property_read_bool(np, "marvell,enable-port1")) 374 pdata->flags |= ENABLE_PORT1; 375 if (of_property_read_bool(np, "marvell,enable-port2")) 376 pdata->flags |= ENABLE_PORT2; 377 if (of_property_read_bool(np, "marvell,enable-port3")) 378 pdata->flags |= ENABLE_PORT3; 379 if (of_property_read_bool(np, "marvell,port-sense-low")) 380 pdata->flags |= POWER_SENSE_LOW; 381 if (of_property_read_bool(np, "marvell,power-control-low")) 382 pdata->flags |= POWER_CONTROL_LOW; 383 if (of_property_read_bool(np, "marvell,no-oc-protection")) 384 pdata->flags |= NO_OC_PROTECTION; 385 if (of_property_read_bool(np, "marvell,oc-mode-perport")) 386 pdata->flags |= OC_MODE_PERPORT; 387 if (!of_property_read_u32(np, "marvell,power-on-delay", &tmp)) 388 pdata->power_on_delay = tmp; 389 if (!of_property_read_u32(np, "marvell,port-mode", &tmp)) 390 pdata->port_mode = tmp; 391 if (!of_property_read_u32(np, "marvell,power-budget", &tmp)) 392 pdata->power_budget = tmp; 393 394 pdev->dev.platform_data = pdata; 395 396 return 0; 397 } 398 #else 399 static int ohci_pxa_of_init(struct platform_device *pdev) 400 { 401 return 0; 402 } 403 #endif 404 405 /*-------------------------------------------------------------------------*/ 406 407 /* configure so an HC device and id are always provided */ 408 /* always called with process context; sleeping is OK */ 409 410 411 /** 412 * ohci_hcd_pxa27x_probe - initialize pxa27x-based HCDs 413 * @pdev: USB Host controller to probe 414 * 415 * Context: task context, might sleep 416 * 417 * Allocates basic resources for this USB host controller, and 418 * then invokes the start() method for the HCD associated with it 419 * through the hotplug entry's driver_data. 420 */ 421 static int ohci_hcd_pxa27x_probe(struct platform_device *pdev) 422 { 423 int retval, irq; 424 struct usb_hcd *hcd; 425 struct pxaohci_platform_data *inf; 426 struct pxa27x_ohci *pxa_ohci; 427 struct ohci_hcd *ohci; 428 struct resource *r; 429 struct clk *usb_clk; 430 unsigned int i; 431 432 retval = ohci_pxa_of_init(pdev); 433 if (retval) 434 return retval; 435 436 inf = dev_get_platdata(&pdev->dev); 437 438 if (!inf) 439 return -ENODEV; 440 441 irq = platform_get_irq(pdev, 0); 442 if (irq < 0) { 443 pr_err("no resource of IORESOURCE_IRQ"); 444 return irq; 445 } 446 447 usb_clk = devm_clk_get(&pdev->dev, NULL); 448 if (IS_ERR(usb_clk)) 449 return PTR_ERR(usb_clk); 450 451 hcd = usb_create_hcd(&ohci_pxa27x_hc_driver, &pdev->dev, "pxa27x"); 452 if (!hcd) 453 return -ENOMEM; 454 455 r = platform_get_resource(pdev, IORESOURCE_MEM, 0); 456 hcd->regs = devm_ioremap_resource(&pdev->dev, r); 457 if (IS_ERR(hcd->regs)) { 458 retval = PTR_ERR(hcd->regs); 459 goto err; 460 } 461 hcd->rsrc_start = r->start; 462 hcd->rsrc_len = resource_size(r); 463 464 /* initialize "struct pxa27x_ohci" */ 465 pxa_ohci = to_pxa27x_ohci(hcd); 466 pxa_ohci->clk = usb_clk; 467 pxa_ohci->mmio_base = (void __iomem *)hcd->regs; 468 469 for (i = 0; i < 3; ++i) { 470 char name[6]; 471 472 if (!(inf->flags & (ENABLE_PORT1 << i))) 473 continue; 474 475 sprintf(name, "vbus%u", i + 1); 476 pxa_ohci->vbus[i] = devm_regulator_get(&pdev->dev, name); 477 } 478 479 retval = pxa27x_start_hc(pxa_ohci, &pdev->dev); 480 if (retval < 0) { 481 pr_debug("pxa27x_start_hc failed"); 482 goto err; 483 } 484 485 /* Select Power Management Mode */ 486 pxa27x_ohci_select_pmm(pxa_ohci, inf->port_mode); 487 488 if (inf->power_budget) 489 hcd->power_budget = inf->power_budget; 490 491 /* The value of NDP in roothub_a is incorrect on this hardware */ 492 ohci = hcd_to_ohci(hcd); 493 ohci->num_ports = 3; 494 495 retval = usb_add_hcd(hcd, irq, 0); 496 if (retval == 0) { 497 device_wakeup_enable(hcd->self.controller); 498 return retval; 499 } 500 501 pxa27x_stop_hc(pxa_ohci, &pdev->dev); 502 err: 503 usb_put_hcd(hcd); 504 return retval; 505 } 506 507 508 /* may be called without controller electrically present */ 509 /* may be called with controller, bus, and devices active */ 510 511 /** 512 * ohci_hcd_pxa27x_remove - shutdown processing for pxa27x-based HCDs 513 * @pdev: USB Host Controller being removed 514 * 515 * Context: task context, might sleep 516 * 517 * Reverses the effect of ohci_hcd_pxa27x_probe(), first invoking 518 * the HCD's stop() method. It is always called from a thread 519 * context, normally "rmmod", "apmd", or something similar. 520 */ 521 static int ohci_hcd_pxa27x_remove(struct platform_device *pdev) 522 { 523 struct usb_hcd *hcd = platform_get_drvdata(pdev); 524 struct pxa27x_ohci *pxa_ohci = to_pxa27x_ohci(hcd); 525 unsigned int i; 526 527 usb_remove_hcd(hcd); 528 pxa27x_stop_hc(pxa_ohci, &pdev->dev); 529 530 for (i = 0; i < 3; ++i) 531 pxa27x_ohci_set_vbus_power(pxa_ohci, i, false); 532 533 usb_put_hcd(hcd); 534 return 0; 535 } 536 537 /*-------------------------------------------------------------------------*/ 538 539 #ifdef CONFIG_PM 540 static int ohci_hcd_pxa27x_drv_suspend(struct device *dev) 541 { 542 struct usb_hcd *hcd = dev_get_drvdata(dev); 543 struct pxa27x_ohci *pxa_ohci = to_pxa27x_ohci(hcd); 544 struct ohci_hcd *ohci = hcd_to_ohci(hcd); 545 bool do_wakeup = device_may_wakeup(dev); 546 int ret; 547 548 549 if (time_before(jiffies, ohci->next_statechange)) 550 msleep(5); 551 ohci->next_statechange = jiffies; 552 553 ret = ohci_suspend(hcd, do_wakeup); 554 if (ret) 555 return ret; 556 557 pxa27x_stop_hc(pxa_ohci, dev); 558 return ret; 559 } 560 561 static int ohci_hcd_pxa27x_drv_resume(struct device *dev) 562 { 563 struct usb_hcd *hcd = dev_get_drvdata(dev); 564 struct pxa27x_ohci *pxa_ohci = to_pxa27x_ohci(hcd); 565 struct pxaohci_platform_data *inf = dev_get_platdata(dev); 566 struct ohci_hcd *ohci = hcd_to_ohci(hcd); 567 int status; 568 569 if (time_before(jiffies, ohci->next_statechange)) 570 msleep(5); 571 ohci->next_statechange = jiffies; 572 573 status = pxa27x_start_hc(pxa_ohci, dev); 574 if (status < 0) 575 return status; 576 577 /* Select Power Management Mode */ 578 pxa27x_ohci_select_pmm(pxa_ohci, inf->port_mode); 579 580 ohci_resume(hcd, false); 581 return 0; 582 } 583 584 static const struct dev_pm_ops ohci_hcd_pxa27x_pm_ops = { 585 .suspend = ohci_hcd_pxa27x_drv_suspend, 586 .resume = ohci_hcd_pxa27x_drv_resume, 587 }; 588 #endif 589 590 static struct platform_driver ohci_hcd_pxa27x_driver = { 591 .probe = ohci_hcd_pxa27x_probe, 592 .remove = ohci_hcd_pxa27x_remove, 593 .shutdown = usb_hcd_platform_shutdown, 594 .driver = { 595 .name = "pxa27x-ohci", 596 .of_match_table = of_match_ptr(pxa_ohci_dt_ids), 597 #ifdef CONFIG_PM 598 .pm = &ohci_hcd_pxa27x_pm_ops, 599 #endif 600 }, 601 }; 602 603 static const struct ohci_driver_overrides pxa27x_overrides __initconst = { 604 .extra_priv_size = sizeof(struct pxa27x_ohci), 605 }; 606 607 static int __init ohci_pxa27x_init(void) 608 { 609 if (usb_disabled()) 610 return -ENODEV; 611 612 pr_info("%s: " DRIVER_DESC "\n", hcd_name); 613 614 ohci_init_driver(&ohci_pxa27x_hc_driver, &pxa27x_overrides); 615 ohci_pxa27x_hc_driver.hub_control = pxa27x_ohci_hub_control; 616 617 return platform_driver_register(&ohci_hcd_pxa27x_driver); 618 } 619 module_init(ohci_pxa27x_init); 620 621 static void __exit ohci_pxa27x_cleanup(void) 622 { 623 platform_driver_unregister(&ohci_hcd_pxa27x_driver); 624 } 625 module_exit(ohci_pxa27x_cleanup); 626 627 MODULE_DESCRIPTION(DRIVER_DESC); 628 MODULE_LICENSE("GPL"); 629 MODULE_ALIAS("platform:pxa27x-ohci"); 630