1 // SPDX-License-Identifier: GPL-2.0+
2 /*
3  * Intel PXA25x and IXP4xx on-chip full speed USB device controllers
4  *
5  * Copyright (C) 2002 Intrinsyc, Inc. (Frank Becker)
6  * Copyright (C) 2003 Robert Schwebel, Pengutronix
7  * Copyright (C) 2003 Benedikt Spranger, Pengutronix
8  * Copyright (C) 2003 David Brownell
9  * Copyright (C) 2003 Joshua Wise
10  */
11 
12 /* #define VERBOSE_DEBUG */
13 
14 #include <linux/device.h>
15 #include <linux/gpio.h>
16 #include <linux/module.h>
17 #include <linux/kernel.h>
18 #include <linux/ioport.h>
19 #include <linux/types.h>
20 #include <linux/errno.h>
21 #include <linux/err.h>
22 #include <linux/delay.h>
23 #include <linux/slab.h>
24 #include <linux/timer.h>
25 #include <linux/list.h>
26 #include <linux/interrupt.h>
27 #include <linux/mm.h>
28 #include <linux/platform_data/pxa2xx_udc.h>
29 #include <linux/platform_device.h>
30 #include <linux/dma-mapping.h>
31 #include <linux/irq.h>
32 #include <linux/clk.h>
33 #include <linux/seq_file.h>
34 #include <linux/debugfs.h>
35 #include <linux/io.h>
36 #include <linux/prefetch.h>
37 
38 #include <asm/byteorder.h>
39 #include <asm/dma.h>
40 #include <asm/mach-types.h>
41 #include <asm/unaligned.h>
42 
43 #include <linux/usb/ch9.h>
44 #include <linux/usb/gadget.h>
45 #include <linux/usb/otg.h>
46 
47 #ifdef CONFIG_ARCH_LUBBOCK
48 #include <mach/lubbock.h>
49 #endif
50 
51 #define UDCCR	 0x0000 /* UDC Control Register */
52 #define UDC_RES1 0x0004 /* UDC Undocumented - Reserved1 */
53 #define UDC_RES2 0x0008 /* UDC Undocumented - Reserved2 */
54 #define UDC_RES3 0x000C /* UDC Undocumented - Reserved3 */
55 #define UDCCS0	 0x0010 /* UDC Endpoint 0 Control/Status Register */
56 #define UDCCS1	 0x0014 /* UDC Endpoint 1 (IN) Control/Status Register */
57 #define UDCCS2	 0x0018 /* UDC Endpoint 2 (OUT) Control/Status Register */
58 #define UDCCS3	 0x001C /* UDC Endpoint 3 (IN) Control/Status Register */
59 #define UDCCS4	 0x0020 /* UDC Endpoint 4 (OUT) Control/Status Register */
60 #define UDCCS5	 0x0024 /* UDC Endpoint 5 (Interrupt) Control/Status Register */
61 #define UDCCS6	 0x0028 /* UDC Endpoint 6 (IN) Control/Status Register */
62 #define UDCCS7	 0x002C /* UDC Endpoint 7 (OUT) Control/Status Register */
63 #define UDCCS8	 0x0030 /* UDC Endpoint 8 (IN) Control/Status Register */
64 #define UDCCS9	 0x0034 /* UDC Endpoint 9 (OUT) Control/Status Register */
65 #define UDCCS10	 0x0038 /* UDC Endpoint 10 (Interrupt) Control/Status Register */
66 #define UDCCS11	 0x003C /* UDC Endpoint 11 (IN) Control/Status Register */
67 #define UDCCS12	 0x0040 /* UDC Endpoint 12 (OUT) Control/Status Register */
68 #define UDCCS13	 0x0044 /* UDC Endpoint 13 (IN) Control/Status Register */
69 #define UDCCS14	 0x0048 /* UDC Endpoint 14 (OUT) Control/Status Register */
70 #define UDCCS15	 0x004C /* UDC Endpoint 15 (Interrupt) Control/Status Register */
71 #define UFNRH	 0x0060 /* UDC Frame Number Register High */
72 #define UFNRL	 0x0064 /* UDC Frame Number Register Low */
73 #define UBCR2	 0x0068 /* UDC Byte Count Reg 2 */
74 #define UBCR4	 0x006c /* UDC Byte Count Reg 4 */
75 #define UBCR7	 0x0070 /* UDC Byte Count Reg 7 */
76 #define UBCR9	 0x0074 /* UDC Byte Count Reg 9 */
77 #define UBCR12	 0x0078 /* UDC Byte Count Reg 12 */
78 #define UBCR14	 0x007c /* UDC Byte Count Reg 14 */
79 #define UDDR0	 0x0080 /* UDC Endpoint 0 Data Register */
80 #define UDDR1	 0x0100 /* UDC Endpoint 1 Data Register */
81 #define UDDR2	 0x0180 /* UDC Endpoint 2 Data Register */
82 #define UDDR3	 0x0200 /* UDC Endpoint 3 Data Register */
83 #define UDDR4	 0x0400 /* UDC Endpoint 4 Data Register */
84 #define UDDR5	 0x00A0 /* UDC Endpoint 5 Data Register */
85 #define UDDR6	 0x0600 /* UDC Endpoint 6 Data Register */
86 #define UDDR7	 0x0680 /* UDC Endpoint 7 Data Register */
87 #define UDDR8	 0x0700 /* UDC Endpoint 8 Data Register */
88 #define UDDR9	 0x0900 /* UDC Endpoint 9 Data Register */
89 #define UDDR10	 0x00C0 /* UDC Endpoint 10 Data Register */
90 #define UDDR11	 0x0B00 /* UDC Endpoint 11 Data Register */
91 #define UDDR12	 0x0B80 /* UDC Endpoint 12 Data Register */
92 #define UDDR13	 0x0C00 /* UDC Endpoint 13 Data Register */
93 #define UDDR14	 0x0E00 /* UDC Endpoint 14 Data Register */
94 #define UDDR15	 0x00E0 /* UDC Endpoint 15 Data Register */
95 
96 #define UICR0	 0x0050 /* UDC Interrupt Control Register 0 */
97 #define UICR1	 0x0054 /* UDC Interrupt Control Register 1 */
98 
99 #define USIR0	 0x0058 /* UDC Status Interrupt Register 0 */
100 #define USIR1	 0x005C /* UDC Status Interrupt Register 1 */
101 
102 #define UDCCR_UDE	(1 << 0)	/* UDC enable */
103 #define UDCCR_UDA	(1 << 1)	/* UDC active */
104 #define UDCCR_RSM	(1 << 2)	/* Device resume */
105 #define UDCCR_RESIR	(1 << 3)	/* Resume interrupt request */
106 #define UDCCR_SUSIR	(1 << 4)	/* Suspend interrupt request */
107 #define UDCCR_SRM	(1 << 5)	/* Suspend/resume interrupt mask */
108 #define UDCCR_RSTIR	(1 << 6)	/* Reset interrupt request */
109 #define UDCCR_REM	(1 << 7)	/* Reset interrupt mask */
110 
111 #define UDCCS0_OPR	(1 << 0)	/* OUT packet ready */
112 #define UDCCS0_IPR	(1 << 1)	/* IN packet ready */
113 #define UDCCS0_FTF	(1 << 2)	/* Flush Tx FIFO */
114 #define UDCCS0_DRWF	(1 << 3)	/* Device remote wakeup feature */
115 #define UDCCS0_SST	(1 << 4)	/* Sent stall */
116 #define UDCCS0_FST	(1 << 5)	/* Force stall */
117 #define UDCCS0_RNE	(1 << 6)	/* Receive FIFO no empty */
118 #define UDCCS0_SA	(1 << 7)	/* Setup active */
119 
120 #define UDCCS_BI_TFS	(1 << 0)	/* Transmit FIFO service */
121 #define UDCCS_BI_TPC	(1 << 1)	/* Transmit packet complete */
122 #define UDCCS_BI_FTF	(1 << 2)	/* Flush Tx FIFO */
123 #define UDCCS_BI_TUR	(1 << 3)	/* Transmit FIFO underrun */
124 #define UDCCS_BI_SST	(1 << 4)	/* Sent stall */
125 #define UDCCS_BI_FST	(1 << 5)	/* Force stall */
126 #define UDCCS_BI_TSP	(1 << 7)	/* Transmit short packet */
127 
128 #define UDCCS_BO_RFS	(1 << 0)	/* Receive FIFO service */
129 #define UDCCS_BO_RPC	(1 << 1)	/* Receive packet complete */
130 #define UDCCS_BO_DME	(1 << 3)	/* DMA enable */
131 #define UDCCS_BO_SST	(1 << 4)	/* Sent stall */
132 #define UDCCS_BO_FST	(1 << 5)	/* Force stall */
133 #define UDCCS_BO_RNE	(1 << 6)	/* Receive FIFO not empty */
134 #define UDCCS_BO_RSP	(1 << 7)	/* Receive short packet */
135 
136 #define UDCCS_II_TFS	(1 << 0)	/* Transmit FIFO service */
137 #define UDCCS_II_TPC	(1 << 1)	/* Transmit packet complete */
138 #define UDCCS_II_FTF	(1 << 2)	/* Flush Tx FIFO */
139 #define UDCCS_II_TUR	(1 << 3)	/* Transmit FIFO underrun */
140 #define UDCCS_II_TSP	(1 << 7)	/* Transmit short packet */
141 
142 #define UDCCS_IO_RFS	(1 << 0)	/* Receive FIFO service */
143 #define UDCCS_IO_RPC	(1 << 1)	/* Receive packet complete */
144 #ifdef CONFIG_ARCH_IXP4XX /* FIXME: is this right?, datasheed says '2' */
145 #define UDCCS_IO_ROF	(1 << 3)	/* Receive overflow */
146 #endif
147 #ifdef CONFIG_ARCH_PXA
148 #define UDCCS_IO_ROF	(1 << 2)	/* Receive overflow */
149 #endif
150 #define UDCCS_IO_DME	(1 << 3)	/* DMA enable */
151 #define UDCCS_IO_RNE	(1 << 6)	/* Receive FIFO not empty */
152 #define UDCCS_IO_RSP	(1 << 7)	/* Receive short packet */
153 
154 #define UDCCS_INT_TFS	(1 << 0)	/* Transmit FIFO service */
155 #define UDCCS_INT_TPC	(1 << 1)	/* Transmit packet complete */
156 #define UDCCS_INT_FTF	(1 << 2)	/* Flush Tx FIFO */
157 #define UDCCS_INT_TUR	(1 << 3)	/* Transmit FIFO underrun */
158 #define UDCCS_INT_SST	(1 << 4)	/* Sent stall */
159 #define UDCCS_INT_FST	(1 << 5)	/* Force stall */
160 #define UDCCS_INT_TSP	(1 << 7)	/* Transmit short packet */
161 
162 #define UICR0_IM0	(1 << 0)	/* Interrupt mask ep 0 */
163 #define UICR0_IM1	(1 << 1)	/* Interrupt mask ep 1 */
164 #define UICR0_IM2	(1 << 2)	/* Interrupt mask ep 2 */
165 #define UICR0_IM3	(1 << 3)	/* Interrupt mask ep 3 */
166 #define UICR0_IM4	(1 << 4)	/* Interrupt mask ep 4 */
167 #define UICR0_IM5	(1 << 5)	/* Interrupt mask ep 5 */
168 #define UICR0_IM6	(1 << 6)	/* Interrupt mask ep 6 */
169 #define UICR0_IM7	(1 << 7)	/* Interrupt mask ep 7 */
170 
171 #define UICR1_IM8	(1 << 0)	/* Interrupt mask ep 8 */
172 #define UICR1_IM9	(1 << 1)	/* Interrupt mask ep 9 */
173 #define UICR1_IM10	(1 << 2)	/* Interrupt mask ep 10 */
174 #define UICR1_IM11	(1 << 3)	/* Interrupt mask ep 11 */
175 #define UICR1_IM12	(1 << 4)	/* Interrupt mask ep 12 */
176 #define UICR1_IM13	(1 << 5)	/* Interrupt mask ep 13 */
177 #define UICR1_IM14	(1 << 6)	/* Interrupt mask ep 14 */
178 #define UICR1_IM15	(1 << 7)	/* Interrupt mask ep 15 */
179 
180 #define USIR0_IR0	(1 << 0)	/* Interrupt request ep 0 */
181 #define USIR0_IR1	(1 << 1)	/* Interrupt request ep 1 */
182 #define USIR0_IR2	(1 << 2)	/* Interrupt request ep 2 */
183 #define USIR0_IR3	(1 << 3)	/* Interrupt request ep 3 */
184 #define USIR0_IR4	(1 << 4)	/* Interrupt request ep 4 */
185 #define USIR0_IR5	(1 << 5)	/* Interrupt request ep 5 */
186 #define USIR0_IR6	(1 << 6)	/* Interrupt request ep 6 */
187 #define USIR0_IR7	(1 << 7)	/* Interrupt request ep 7 */
188 
189 #define USIR1_IR8	(1 << 0)	/* Interrupt request ep 8 */
190 #define USIR1_IR9	(1 << 1)	/* Interrupt request ep 9 */
191 #define USIR1_IR10	(1 << 2)	/* Interrupt request ep 10 */
192 #define USIR1_IR11	(1 << 3)	/* Interrupt request ep 11 */
193 #define USIR1_IR12	(1 << 4)	/* Interrupt request ep 12 */
194 #define USIR1_IR13	(1 << 5)	/* Interrupt request ep 13 */
195 #define USIR1_IR14	(1 << 6)	/* Interrupt request ep 14 */
196 #define USIR1_IR15	(1 << 7)	/* Interrupt request ep 15 */
197 
198 /*
199  * This driver handles the USB Device Controller (UDC) in Intel's PXA 25x
200  * series processors.  The UDC for the IXP 4xx series is very similar.
201  * There are fifteen endpoints, in addition to ep0.
202  *
203  * Such controller drivers work with a gadget driver.  The gadget driver
204  * returns descriptors, implements configuration and data protocols used
205  * by the host to interact with this device, and allocates endpoints to
206  * the different protocol interfaces.  The controller driver virtualizes
207  * usb hardware so that the gadget drivers will be more portable.
208  *
209  * This UDC hardware wants to implement a bit too much USB protocol, so
210  * it constrains the sorts of USB configuration change events that work.
211  * The errata for these chips are misleading; some "fixed" bugs from
212  * pxa250 a0/a1 b0/b1/b2 sure act like they're still there.
213  *
214  * Note that the UDC hardware supports DMA (except on IXP) but that's
215  * not used here.  IN-DMA (to host) is simple enough, when the data is
216  * suitably aligned (16 bytes) ... the network stack doesn't do that,
217  * other software can.  OUT-DMA is buggy in most chip versions, as well
218  * as poorly designed (data toggle not automatic).  So this driver won't
219  * bother using DMA.  (Mostly-working IN-DMA support was available in
220  * kernels before 2.6.23, but was never enabled or well tested.)
221  */
222 
223 #define	DRIVER_VERSION	"30-June-2007"
224 #define	DRIVER_DESC	"PXA 25x USB Device Controller driver"
225 
226 
227 static const char driver_name [] = "pxa25x_udc";
228 
229 static const char ep0name [] = "ep0";
230 
231 
232 #ifdef CONFIG_ARCH_IXP4XX
233 
234 /* cpu-specific register addresses are compiled in to this code */
235 #ifdef CONFIG_ARCH_PXA
236 #error "Can't configure both IXP and PXA"
237 #endif
238 
239 /* IXP doesn't yet support <linux/clk.h> */
240 #define clk_get(dev,name)	NULL
241 #define clk_enable(clk)		do { } while (0)
242 #define clk_disable(clk)	do { } while (0)
243 #define clk_put(clk)		do { } while (0)
244 
245 #endif
246 
247 #include "pxa25x_udc.h"
248 
249 
250 #ifdef	CONFIG_USB_PXA25X_SMALL
251 #define SIZE_STR	" (small)"
252 #else
253 #define SIZE_STR	""
254 #endif
255 
256 /* ---------------------------------------------------------------------------
257  *	endpoint related parts of the api to the usb controller hardware,
258  *	used by gadget driver; and the inner talker-to-hardware core.
259  * ---------------------------------------------------------------------------
260  */
261 
262 static void pxa25x_ep_fifo_flush (struct usb_ep *ep);
263 static void nuke (struct pxa25x_ep *, int status);
264 
265 /* one GPIO should control a D+ pullup, so host sees this device (or not) */
266 static void pullup_off(void)
267 {
268 	struct pxa2xx_udc_mach_info		*mach = the_controller->mach;
269 	int off_level = mach->gpio_pullup_inverted;
270 
271 	if (gpio_is_valid(mach->gpio_pullup))
272 		gpio_set_value(mach->gpio_pullup, off_level);
273 	else if (mach->udc_command)
274 		mach->udc_command(PXA2XX_UDC_CMD_DISCONNECT);
275 }
276 
277 static void pullup_on(void)
278 {
279 	struct pxa2xx_udc_mach_info		*mach = the_controller->mach;
280 	int on_level = !mach->gpio_pullup_inverted;
281 
282 	if (gpio_is_valid(mach->gpio_pullup))
283 		gpio_set_value(mach->gpio_pullup, on_level);
284 	else if (mach->udc_command)
285 		mach->udc_command(PXA2XX_UDC_CMD_CONNECT);
286 }
287 
288 #if defined(CONFIG_CPU_BIG_ENDIAN)
289 /*
290  * IXP4xx has its buses wired up in a way that relies on never doing any
291  * byte swaps, independent of whether it runs in big-endian or little-endian
292  * mode, as explained by Krzysztof Hałasa.
293  *
294  * We only support pxa25x in little-endian mode, but it is very likely
295  * that it works the same way.
296  */
297 static inline void udc_set_reg(struct pxa25x_udc *dev, u32 reg, u32 val)
298 {
299 	iowrite32be(val, dev->regs + reg);
300 }
301 
302 static inline u32 udc_get_reg(struct pxa25x_udc *dev, u32 reg)
303 {
304 	return ioread32be(dev->regs + reg);
305 }
306 #else
307 static inline void udc_set_reg(struct pxa25x_udc *dev, u32 reg, u32 val)
308 {
309 	writel(val, dev->regs + reg);
310 }
311 
312 static inline u32 udc_get_reg(struct pxa25x_udc *dev, u32 reg)
313 {
314 	return readl(dev->regs + reg);
315 }
316 #endif
317 
318 static void pio_irq_enable(struct pxa25x_ep *ep)
319 {
320 	u32 bEndpointAddress = ep->bEndpointAddress & 0xf;
321 
322         if (bEndpointAddress < 8)
323 		udc_set_reg(ep->dev, UICR0, udc_get_reg(ep->dev, UICR0) &
324 						~(1 << bEndpointAddress));
325         else {
326                 bEndpointAddress -= 8;
327 		udc_set_reg(ep->dev, UICR1, udc_get_reg(ep->dev, UICR1) &
328 						~(1 << bEndpointAddress));
329 	}
330 }
331 
332 static void pio_irq_disable(struct pxa25x_ep *ep)
333 {
334 	u32 bEndpointAddress = ep->bEndpointAddress & 0xf;
335 
336         if (bEndpointAddress < 8)
337                 udc_set_reg(ep->dev, UICR0, udc_get_reg(ep->dev, UICR0) |
338 						(1 << bEndpointAddress));
339         else {
340                 bEndpointAddress -= 8;
341                 udc_set_reg(ep->dev, UICR1, udc_get_reg(ep->dev, UICR1) |
342 						(1 << bEndpointAddress));
343         }
344 }
345 
346 /* The UDCCR reg contains mask and interrupt status bits,
347  * so using '|=' isn't safe as it may ack an interrupt.
348  */
349 #define UDCCR_MASK_BITS         (UDCCR_REM | UDCCR_SRM | UDCCR_UDE)
350 
351 static inline void udc_set_mask_UDCCR(struct pxa25x_udc *dev, int mask)
352 {
353 	u32 udccr = udc_get_reg(dev, UDCCR);
354 
355 	udc_set_reg(dev, (udccr & UDCCR_MASK_BITS) | (mask & UDCCR_MASK_BITS), UDCCR);
356 }
357 
358 static inline void udc_clear_mask_UDCCR(struct pxa25x_udc *dev, int mask)
359 {
360 	u32 udccr = udc_get_reg(dev, UDCCR);
361 
362 	udc_set_reg(dev, (udccr & UDCCR_MASK_BITS) & ~(mask & UDCCR_MASK_BITS), UDCCR);
363 }
364 
365 static inline void udc_ack_int_UDCCR(struct pxa25x_udc *dev, int mask)
366 {
367 	/* udccr contains the bits we dont want to change */
368 	u32 udccr = udc_get_reg(dev, UDCCR) & UDCCR_MASK_BITS;
369 
370 	udc_set_reg(dev, udccr | (mask & ~UDCCR_MASK_BITS), UDCCR);
371 }
372 
373 static inline u32 udc_ep_get_UDCCS(struct pxa25x_ep *ep)
374 {
375 	return udc_get_reg(ep->dev, ep->regoff_udccs);
376 }
377 
378 static inline void udc_ep_set_UDCCS(struct pxa25x_ep *ep, u32 data)
379 {
380 	udc_set_reg(ep->dev, data, ep->regoff_udccs);
381 }
382 
383 static inline u32 udc_ep0_get_UDCCS(struct pxa25x_udc *dev)
384 {
385 	return udc_get_reg(dev, UDCCS0);
386 }
387 
388 static inline void udc_ep0_set_UDCCS(struct pxa25x_udc *dev, u32 data)
389 {
390 	udc_set_reg(dev, data, UDCCS0);
391 }
392 
393 static inline u32 udc_ep_get_UDDR(struct pxa25x_ep *ep)
394 {
395 	return udc_get_reg(ep->dev, ep->regoff_uddr);
396 }
397 
398 static inline void udc_ep_set_UDDR(struct pxa25x_ep *ep, u32 data)
399 {
400 	udc_set_reg(ep->dev, data, ep->regoff_uddr);
401 }
402 
403 static inline u32 udc_ep_get_UBCR(struct pxa25x_ep *ep)
404 {
405 	return udc_get_reg(ep->dev, ep->regoff_ubcr);
406 }
407 
408 /*
409  * endpoint enable/disable
410  *
411  * we need to verify the descriptors used to enable endpoints.  since pxa25x
412  * endpoint configurations are fixed, and are pretty much always enabled,
413  * there's not a lot to manage here.
414  *
415  * because pxa25x can't selectively initialize bulk (or interrupt) endpoints,
416  * (resetting endpoint halt and toggle), SET_INTERFACE is unusable except
417  * for a single interface (with only the default altsetting) and for gadget
418  * drivers that don't halt endpoints (not reset by set_interface).  that also
419  * means that if you use ISO, you must violate the USB spec rule that all
420  * iso endpoints must be in non-default altsettings.
421  */
422 static int pxa25x_ep_enable (struct usb_ep *_ep,
423 		const struct usb_endpoint_descriptor *desc)
424 {
425 	struct pxa25x_ep        *ep;
426 	struct pxa25x_udc       *dev;
427 
428 	ep = container_of (_ep, struct pxa25x_ep, ep);
429 	if (!_ep || !desc || _ep->name == ep0name
430 			|| desc->bDescriptorType != USB_DT_ENDPOINT
431 			|| ep->bEndpointAddress != desc->bEndpointAddress
432 			|| ep->fifo_size < usb_endpoint_maxp (desc)) {
433 		DMSG("%s, bad ep or descriptor\n", __func__);
434 		return -EINVAL;
435 	}
436 
437 	/* xfer types must match, except that interrupt ~= bulk */
438 	if (ep->bmAttributes != desc->bmAttributes
439 			&& ep->bmAttributes != USB_ENDPOINT_XFER_BULK
440 			&& desc->bmAttributes != USB_ENDPOINT_XFER_INT) {
441 		DMSG("%s, %s type mismatch\n", __func__, _ep->name);
442 		return -EINVAL;
443 	}
444 
445 	/* hardware _could_ do smaller, but driver doesn't */
446 	if ((desc->bmAttributes == USB_ENDPOINT_XFER_BULK
447 				&& usb_endpoint_maxp (desc)
448 						!= BULK_FIFO_SIZE)
449 			|| !desc->wMaxPacketSize) {
450 		DMSG("%s, bad %s maxpacket\n", __func__, _ep->name);
451 		return -ERANGE;
452 	}
453 
454 	dev = ep->dev;
455 	if (!dev->driver || dev->gadget.speed == USB_SPEED_UNKNOWN) {
456 		DMSG("%s, bogus device state\n", __func__);
457 		return -ESHUTDOWN;
458 	}
459 
460 	ep->ep.desc = desc;
461 	ep->stopped = 0;
462 	ep->pio_irqs = 0;
463 	ep->ep.maxpacket = usb_endpoint_maxp (desc);
464 
465 	/* flush fifo (mostly for OUT buffers) */
466 	pxa25x_ep_fifo_flush (_ep);
467 
468 	/* ... reset halt state too, if we could ... */
469 
470 	DBG(DBG_VERBOSE, "enabled %s\n", _ep->name);
471 	return 0;
472 }
473 
474 static int pxa25x_ep_disable (struct usb_ep *_ep)
475 {
476 	struct pxa25x_ep	*ep;
477 	unsigned long		flags;
478 
479 	ep = container_of (_ep, struct pxa25x_ep, ep);
480 	if (!_ep || !ep->ep.desc) {
481 		DMSG("%s, %s not enabled\n", __func__,
482 			_ep ? ep->ep.name : NULL);
483 		return -EINVAL;
484 	}
485 	local_irq_save(flags);
486 
487 	nuke (ep, -ESHUTDOWN);
488 
489 	/* flush fifo (mostly for IN buffers) */
490 	pxa25x_ep_fifo_flush (_ep);
491 
492 	ep->ep.desc = NULL;
493 	ep->stopped = 1;
494 
495 	local_irq_restore(flags);
496 	DBG(DBG_VERBOSE, "%s disabled\n", _ep->name);
497 	return 0;
498 }
499 
500 /*-------------------------------------------------------------------------*/
501 
502 /* for the pxa25x, these can just wrap kmalloc/kfree.  gadget drivers
503  * must still pass correctly initialized endpoints, since other controller
504  * drivers may care about how it's currently set up (dma issues etc).
505  */
506 
507 /*
508  *	pxa25x_ep_alloc_request - allocate a request data structure
509  */
510 static struct usb_request *
511 pxa25x_ep_alloc_request (struct usb_ep *_ep, gfp_t gfp_flags)
512 {
513 	struct pxa25x_request *req;
514 
515 	req = kzalloc(sizeof(*req), gfp_flags);
516 	if (!req)
517 		return NULL;
518 
519 	INIT_LIST_HEAD (&req->queue);
520 	return &req->req;
521 }
522 
523 
524 /*
525  *	pxa25x_ep_free_request - deallocate a request data structure
526  */
527 static void
528 pxa25x_ep_free_request (struct usb_ep *_ep, struct usb_request *_req)
529 {
530 	struct pxa25x_request	*req;
531 
532 	req = container_of (_req, struct pxa25x_request, req);
533 	WARN_ON(!list_empty (&req->queue));
534 	kfree(req);
535 }
536 
537 /*-------------------------------------------------------------------------*/
538 
539 /*
540  *	done - retire a request; caller blocked irqs
541  */
542 static void done(struct pxa25x_ep *ep, struct pxa25x_request *req, int status)
543 {
544 	unsigned		stopped = ep->stopped;
545 
546 	list_del_init(&req->queue);
547 
548 	if (likely (req->req.status == -EINPROGRESS))
549 		req->req.status = status;
550 	else
551 		status = req->req.status;
552 
553 	if (status && status != -ESHUTDOWN)
554 		DBG(DBG_VERBOSE, "complete %s req %p stat %d len %u/%u\n",
555 			ep->ep.name, &req->req, status,
556 			req->req.actual, req->req.length);
557 
558 	/* don't modify queue heads during completion callback */
559 	ep->stopped = 1;
560 	usb_gadget_giveback_request(&ep->ep, &req->req);
561 	ep->stopped = stopped;
562 }
563 
564 
565 static inline void ep0_idle (struct pxa25x_udc *dev)
566 {
567 	dev->ep0state = EP0_IDLE;
568 }
569 
570 static int
571 write_packet(struct pxa25x_ep *ep, struct pxa25x_request *req, unsigned max)
572 {
573 	u8		*buf;
574 	unsigned	length, count;
575 
576 	buf = req->req.buf + req->req.actual;
577 	prefetch(buf);
578 
579 	/* how big will this packet be? */
580 	length = min(req->req.length - req->req.actual, max);
581 	req->req.actual += length;
582 
583 	count = length;
584 	while (likely(count--))
585 		udc_ep_set_UDDR(ep, *buf++);
586 
587 	return length;
588 }
589 
590 /*
591  * write to an IN endpoint fifo, as many packets as possible.
592  * irqs will use this to write the rest later.
593  * caller guarantees at least one packet buffer is ready (or a zlp).
594  */
595 static int
596 write_fifo (struct pxa25x_ep *ep, struct pxa25x_request *req)
597 {
598 	unsigned		max;
599 
600 	max = usb_endpoint_maxp(ep->ep.desc);
601 	do {
602 		unsigned	count;
603 		int		is_last, is_short;
604 
605 		count = write_packet(ep, req, max);
606 
607 		/* last packet is usually short (or a zlp) */
608 		if (unlikely (count != max))
609 			is_last = is_short = 1;
610 		else {
611 			if (likely(req->req.length != req->req.actual)
612 					|| req->req.zero)
613 				is_last = 0;
614 			else
615 				is_last = 1;
616 			/* interrupt/iso maxpacket may not fill the fifo */
617 			is_short = unlikely (max < ep->fifo_size);
618 		}
619 
620 		DBG(DBG_VERY_NOISY, "wrote %s %d bytes%s%s %d left %p\n",
621 			ep->ep.name, count,
622 			is_last ? "/L" : "", is_short ? "/S" : "",
623 			req->req.length - req->req.actual, req);
624 
625 		/* let loose that packet. maybe try writing another one,
626 		 * double buffering might work.  TSP, TPC, and TFS
627 		 * bit values are the same for all normal IN endpoints.
628 		 */
629 		udc_ep_set_UDCCS(ep, UDCCS_BI_TPC);
630 		if (is_short)
631 			udc_ep_set_UDCCS(ep, UDCCS_BI_TSP);
632 
633 		/* requests complete when all IN data is in the FIFO */
634 		if (is_last) {
635 			done (ep, req, 0);
636 			if (list_empty(&ep->queue))
637 				pio_irq_disable(ep);
638 			return 1;
639 		}
640 
641 		// TODO experiment: how robust can fifo mode tweaking be?
642 		// double buffering is off in the default fifo mode, which
643 		// prevents TFS from being set here.
644 
645 	} while (udc_ep_get_UDCCS(ep) & UDCCS_BI_TFS);
646 	return 0;
647 }
648 
649 /* caller asserts req->pending (ep0 irq status nyet cleared); starts
650  * ep0 data stage.  these chips want very simple state transitions.
651  */
652 static inline
653 void ep0start(struct pxa25x_udc *dev, u32 flags, const char *tag)
654 {
655 	udc_ep0_set_UDCCS(dev, flags|UDCCS0_SA|UDCCS0_OPR);
656 	udc_set_reg(dev, USIR0, USIR0_IR0);
657 	dev->req_pending = 0;
658 	DBG(DBG_VERY_NOISY, "%s %s, %02x/%02x\n",
659 		__func__, tag, udc_ep0_get_UDCCS(dev), flags);
660 }
661 
662 static int
663 write_ep0_fifo (struct pxa25x_ep *ep, struct pxa25x_request *req)
664 {
665 	struct pxa25x_udc *dev = ep->dev;
666 	unsigned	count;
667 	int		is_short;
668 
669 	count = write_packet(&dev->ep[0], req, EP0_FIFO_SIZE);
670 	ep->dev->stats.write.bytes += count;
671 
672 	/* last packet "must be" short (or a zlp) */
673 	is_short = (count != EP0_FIFO_SIZE);
674 
675 	DBG(DBG_VERY_NOISY, "ep0in %d bytes %d left %p\n", count,
676 		req->req.length - req->req.actual, req);
677 
678 	if (unlikely (is_short)) {
679 		if (ep->dev->req_pending)
680 			ep0start(ep->dev, UDCCS0_IPR, "short IN");
681 		else
682 			udc_ep0_set_UDCCS(dev, UDCCS0_IPR);
683 
684 		count = req->req.length;
685 		done (ep, req, 0);
686 		ep0_idle(ep->dev);
687 #ifndef CONFIG_ARCH_IXP4XX
688 #if 1
689 		/* This seems to get rid of lost status irqs in some cases:
690 		 * host responds quickly, or next request involves config
691 		 * change automagic, or should have been hidden, or ...
692 		 *
693 		 * FIXME get rid of all udelays possible...
694 		 */
695 		if (count >= EP0_FIFO_SIZE) {
696 			count = 100;
697 			do {
698 				if ((udc_ep0_get_UDCCS(dev) & UDCCS0_OPR) != 0) {
699 					/* clear OPR, generate ack */
700 					udc_ep0_set_UDCCS(dev, UDCCS0_OPR);
701 					break;
702 				}
703 				count--;
704 				udelay(1);
705 			} while (count);
706 		}
707 #endif
708 #endif
709 	} else if (ep->dev->req_pending)
710 		ep0start(ep->dev, 0, "IN");
711 	return is_short;
712 }
713 
714 
715 /*
716  * read_fifo -  unload packet(s) from the fifo we use for usb OUT
717  * transfers and put them into the request.  caller should have made
718  * sure there's at least one packet ready.
719  *
720  * returns true if the request completed because of short packet or the
721  * request buffer having filled (and maybe overran till end-of-packet).
722  */
723 static int
724 read_fifo (struct pxa25x_ep *ep, struct pxa25x_request *req)
725 {
726 	for (;;) {
727 		u32		udccs;
728 		u8		*buf;
729 		unsigned	bufferspace, count, is_short;
730 
731 		/* make sure there's a packet in the FIFO.
732 		 * UDCCS_{BO,IO}_RPC are all the same bit value.
733 		 * UDCCS_{BO,IO}_RNE are all the same bit value.
734 		 */
735 		udccs = udc_ep_get_UDCCS(ep);
736 		if (unlikely ((udccs & UDCCS_BO_RPC) == 0))
737 			break;
738 		buf = req->req.buf + req->req.actual;
739 		prefetchw(buf);
740 		bufferspace = req->req.length - req->req.actual;
741 
742 		/* read all bytes from this packet */
743 		if (likely (udccs & UDCCS_BO_RNE)) {
744 			count = 1 + (0x0ff & udc_ep_get_UBCR(ep));
745 			req->req.actual += min (count, bufferspace);
746 		} else /* zlp */
747 			count = 0;
748 		is_short = (count < ep->ep.maxpacket);
749 		DBG(DBG_VERY_NOISY, "read %s %02x, %d bytes%s req %p %d/%d\n",
750 			ep->ep.name, udccs, count,
751 			is_short ? "/S" : "",
752 			req, req->req.actual, req->req.length);
753 		while (likely (count-- != 0)) {
754 			u8	byte = (u8) udc_ep_get_UDDR(ep);
755 
756 			if (unlikely (bufferspace == 0)) {
757 				/* this happens when the driver's buffer
758 				 * is smaller than what the host sent.
759 				 * discard the extra data.
760 				 */
761 				if (req->req.status != -EOVERFLOW)
762 					DMSG("%s overflow %d\n",
763 						ep->ep.name, count);
764 				req->req.status = -EOVERFLOW;
765 			} else {
766 				*buf++ = byte;
767 				bufferspace--;
768 			}
769 		}
770 		udc_ep_set_UDCCS(ep, UDCCS_BO_RPC);
771 		/* RPC/RSP/RNE could now reflect the other packet buffer */
772 
773 		/* iso is one request per packet */
774 		if (ep->bmAttributes == USB_ENDPOINT_XFER_ISOC) {
775 			if (udccs & UDCCS_IO_ROF)
776 				req->req.status = -EHOSTUNREACH;
777 			/* more like "is_done" */
778 			is_short = 1;
779 		}
780 
781 		/* completion */
782 		if (is_short || req->req.actual == req->req.length) {
783 			done (ep, req, 0);
784 			if (list_empty(&ep->queue))
785 				pio_irq_disable(ep);
786 			return 1;
787 		}
788 
789 		/* finished that packet.  the next one may be waiting... */
790 	}
791 	return 0;
792 }
793 
794 /*
795  * special ep0 version of the above.  no UBCR0 or double buffering; status
796  * handshaking is magic.  most device protocols don't need control-OUT.
797  * CDC vendor commands (and RNDIS), mass storage CB/CBI, and some other
798  * protocols do use them.
799  */
800 static int
801 read_ep0_fifo (struct pxa25x_ep *ep, struct pxa25x_request *req)
802 {
803 	u8		*buf, byte;
804 	unsigned	bufferspace;
805 
806 	buf = req->req.buf + req->req.actual;
807 	bufferspace = req->req.length - req->req.actual;
808 
809 	while (udc_ep_get_UDCCS(ep) & UDCCS0_RNE) {
810 		byte = (u8) UDDR0;
811 
812 		if (unlikely (bufferspace == 0)) {
813 			/* this happens when the driver's buffer
814 			 * is smaller than what the host sent.
815 			 * discard the extra data.
816 			 */
817 			if (req->req.status != -EOVERFLOW)
818 				DMSG("%s overflow\n", ep->ep.name);
819 			req->req.status = -EOVERFLOW;
820 		} else {
821 			*buf++ = byte;
822 			req->req.actual++;
823 			bufferspace--;
824 		}
825 	}
826 
827 	udc_ep_set_UDCCS(ep, UDCCS0_OPR | UDCCS0_IPR);
828 
829 	/* completion */
830 	if (req->req.actual >= req->req.length)
831 		return 1;
832 
833 	/* finished that packet.  the next one may be waiting... */
834 	return 0;
835 }
836 
837 /*-------------------------------------------------------------------------*/
838 
839 static int
840 pxa25x_ep_queue(struct usb_ep *_ep, struct usb_request *_req, gfp_t gfp_flags)
841 {
842 	struct pxa25x_request	*req;
843 	struct pxa25x_ep	*ep;
844 	struct pxa25x_udc	*dev;
845 	unsigned long		flags;
846 
847 	req = container_of(_req, struct pxa25x_request, req);
848 	if (unlikely (!_req || !_req->complete || !_req->buf
849 			|| !list_empty(&req->queue))) {
850 		DMSG("%s, bad params\n", __func__);
851 		return -EINVAL;
852 	}
853 
854 	ep = container_of(_ep, struct pxa25x_ep, ep);
855 	if (unlikely(!_ep || (!ep->ep.desc && ep->ep.name != ep0name))) {
856 		DMSG("%s, bad ep\n", __func__);
857 		return -EINVAL;
858 	}
859 
860 	dev = ep->dev;
861 	if (unlikely (!dev->driver
862 			|| dev->gadget.speed == USB_SPEED_UNKNOWN)) {
863 		DMSG("%s, bogus device state\n", __func__);
864 		return -ESHUTDOWN;
865 	}
866 
867 	/* iso is always one packet per request, that's the only way
868 	 * we can report per-packet status.  that also helps with dma.
869 	 */
870 	if (unlikely (ep->bmAttributes == USB_ENDPOINT_XFER_ISOC
871 			&& req->req.length > usb_endpoint_maxp(ep->ep.desc)))
872 		return -EMSGSIZE;
873 
874 	DBG(DBG_NOISY, "%s queue req %p, len %d buf %p\n",
875 		_ep->name, _req, _req->length, _req->buf);
876 
877 	local_irq_save(flags);
878 
879 	_req->status = -EINPROGRESS;
880 	_req->actual = 0;
881 
882 	/* kickstart this i/o queue? */
883 	if (list_empty(&ep->queue) && !ep->stopped) {
884 		if (ep->ep.desc == NULL/* ep0 */) {
885 			unsigned	length = _req->length;
886 
887 			switch (dev->ep0state) {
888 			case EP0_IN_DATA_PHASE:
889 				dev->stats.write.ops++;
890 				if (write_ep0_fifo(ep, req))
891 					req = NULL;
892 				break;
893 
894 			case EP0_OUT_DATA_PHASE:
895 				dev->stats.read.ops++;
896 				/* messy ... */
897 				if (dev->req_config) {
898 					DBG(DBG_VERBOSE, "ep0 config ack%s\n",
899 						dev->has_cfr ?  "" : " raced");
900 					if (dev->has_cfr)
901 						udc_set_reg(dev, UDCCFR, UDCCFR_AREN |
902 							    UDCCFR_ACM | UDCCFR_MB1);
903 					done(ep, req, 0);
904 					dev->ep0state = EP0_END_XFER;
905 					local_irq_restore (flags);
906 					return 0;
907 				}
908 				if (dev->req_pending)
909 					ep0start(dev, UDCCS0_IPR, "OUT");
910 				if (length == 0 || ((udc_ep0_get_UDCCS(dev) & UDCCS0_RNE) != 0
911 						&& read_ep0_fifo(ep, req))) {
912 					ep0_idle(dev);
913 					done(ep, req, 0);
914 					req = NULL;
915 				}
916 				break;
917 
918 			default:
919 				DMSG("ep0 i/o, odd state %d\n", dev->ep0state);
920 				local_irq_restore (flags);
921 				return -EL2HLT;
922 			}
923 		/* can the FIFO can satisfy the request immediately? */
924 		} else if ((ep->bEndpointAddress & USB_DIR_IN) != 0) {
925 			if ((udc_ep_get_UDCCS(ep) & UDCCS_BI_TFS) != 0
926 					&& write_fifo(ep, req))
927 				req = NULL;
928 		} else if ((udc_ep_get_UDCCS(ep) & UDCCS_BO_RFS) != 0
929 				&& read_fifo(ep, req)) {
930 			req = NULL;
931 		}
932 
933 		if (likely(req && ep->ep.desc))
934 			pio_irq_enable(ep);
935 	}
936 
937 	/* pio or dma irq handler advances the queue. */
938 	if (likely(req != NULL))
939 		list_add_tail(&req->queue, &ep->queue);
940 	local_irq_restore(flags);
941 
942 	return 0;
943 }
944 
945 
946 /*
947  *	nuke - dequeue ALL requests
948  */
949 static void nuke(struct pxa25x_ep *ep, int status)
950 {
951 	struct pxa25x_request *req;
952 
953 	/* called with irqs blocked */
954 	while (!list_empty(&ep->queue)) {
955 		req = list_entry(ep->queue.next,
956 				struct pxa25x_request,
957 				queue);
958 		done(ep, req, status);
959 	}
960 	if (ep->ep.desc)
961 		pio_irq_disable(ep);
962 }
963 
964 
965 /* dequeue JUST ONE request */
966 static int pxa25x_ep_dequeue(struct usb_ep *_ep, struct usb_request *_req)
967 {
968 	struct pxa25x_ep	*ep;
969 	struct pxa25x_request	*req;
970 	unsigned long		flags;
971 
972 	ep = container_of(_ep, struct pxa25x_ep, ep);
973 	if (!_ep || ep->ep.name == ep0name)
974 		return -EINVAL;
975 
976 	local_irq_save(flags);
977 
978 	/* make sure it's actually queued on this endpoint */
979 	list_for_each_entry (req, &ep->queue, queue) {
980 		if (&req->req == _req)
981 			break;
982 	}
983 	if (&req->req != _req) {
984 		local_irq_restore(flags);
985 		return -EINVAL;
986 	}
987 
988 	done(ep, req, -ECONNRESET);
989 
990 	local_irq_restore(flags);
991 	return 0;
992 }
993 
994 /*-------------------------------------------------------------------------*/
995 
996 static int pxa25x_ep_set_halt(struct usb_ep *_ep, int value)
997 {
998 	struct pxa25x_ep	*ep;
999 	unsigned long		flags;
1000 
1001 	ep = container_of(_ep, struct pxa25x_ep, ep);
1002 	if (unlikely (!_ep
1003 			|| (!ep->ep.desc && ep->ep.name != ep0name))
1004 			|| ep->bmAttributes == USB_ENDPOINT_XFER_ISOC) {
1005 		DMSG("%s, bad ep\n", __func__);
1006 		return -EINVAL;
1007 	}
1008 	if (value == 0) {
1009 		/* this path (reset toggle+halt) is needed to implement
1010 		 * SET_INTERFACE on normal hardware.  but it can't be
1011 		 * done from software on the PXA UDC, and the hardware
1012 		 * forgets to do it as part of SET_INTERFACE automagic.
1013 		 */
1014 		DMSG("only host can clear %s halt\n", _ep->name);
1015 		return -EROFS;
1016 	}
1017 
1018 	local_irq_save(flags);
1019 
1020 	if ((ep->bEndpointAddress & USB_DIR_IN) != 0
1021 			&& ((udc_ep_get_UDCCS(ep) & UDCCS_BI_TFS) == 0
1022 			   || !list_empty(&ep->queue))) {
1023 		local_irq_restore(flags);
1024 		return -EAGAIN;
1025 	}
1026 
1027 	/* FST bit is the same for control, bulk in, bulk out, interrupt in */
1028 	udc_ep_set_UDCCS(ep, UDCCS_BI_FST|UDCCS_BI_FTF);
1029 
1030 	/* ep0 needs special care */
1031 	if (!ep->ep.desc) {
1032 		start_watchdog(ep->dev);
1033 		ep->dev->req_pending = 0;
1034 		ep->dev->ep0state = EP0_STALL;
1035 
1036 	/* and bulk/intr endpoints like dropping stalls too */
1037 	} else {
1038 		unsigned i;
1039 		for (i = 0; i < 1000; i += 20) {
1040 			if (udc_ep_get_UDCCS(ep) & UDCCS_BI_SST)
1041 				break;
1042 			udelay(20);
1043 		}
1044 	}
1045 	local_irq_restore(flags);
1046 
1047 	DBG(DBG_VERBOSE, "%s halt\n", _ep->name);
1048 	return 0;
1049 }
1050 
1051 static int pxa25x_ep_fifo_status(struct usb_ep *_ep)
1052 {
1053 	struct pxa25x_ep        *ep;
1054 
1055 	ep = container_of(_ep, struct pxa25x_ep, ep);
1056 	if (!_ep) {
1057 		DMSG("%s, bad ep\n", __func__);
1058 		return -ENODEV;
1059 	}
1060 	/* pxa can't report unclaimed bytes from IN fifos */
1061 	if ((ep->bEndpointAddress & USB_DIR_IN) != 0)
1062 		return -EOPNOTSUPP;
1063 	if (ep->dev->gadget.speed == USB_SPEED_UNKNOWN
1064 			|| (udc_ep_get_UDCCS(ep) & UDCCS_BO_RFS) == 0)
1065 		return 0;
1066 	else
1067 		return (udc_ep_get_UBCR(ep) & 0xfff) + 1;
1068 }
1069 
1070 static void pxa25x_ep_fifo_flush(struct usb_ep *_ep)
1071 {
1072 	struct pxa25x_ep        *ep;
1073 
1074 	ep = container_of(_ep, struct pxa25x_ep, ep);
1075 	if (!_ep || ep->ep.name == ep0name || !list_empty(&ep->queue)) {
1076 		DMSG("%s, bad ep\n", __func__);
1077 		return;
1078 	}
1079 
1080 	/* toggle and halt bits stay unchanged */
1081 
1082 	/* for OUT, just read and discard the FIFO contents. */
1083 	if ((ep->bEndpointAddress & USB_DIR_IN) == 0) {
1084 		while (((udc_ep_get_UDCCS(ep)) & UDCCS_BO_RNE) != 0)
1085 			(void)udc_ep_get_UDDR(ep);
1086 		return;
1087 	}
1088 
1089 	/* most IN status is the same, but ISO can't stall */
1090 	udc_ep_set_UDCCS(ep, UDCCS_BI_TPC|UDCCS_BI_FTF|UDCCS_BI_TUR
1091 		| (ep->bmAttributes == USB_ENDPOINT_XFER_ISOC
1092 			? 0 : UDCCS_BI_SST));
1093 }
1094 
1095 
1096 static struct usb_ep_ops pxa25x_ep_ops = {
1097 	.enable		= pxa25x_ep_enable,
1098 	.disable	= pxa25x_ep_disable,
1099 
1100 	.alloc_request	= pxa25x_ep_alloc_request,
1101 	.free_request	= pxa25x_ep_free_request,
1102 
1103 	.queue		= pxa25x_ep_queue,
1104 	.dequeue	= pxa25x_ep_dequeue,
1105 
1106 	.set_halt	= pxa25x_ep_set_halt,
1107 	.fifo_status	= pxa25x_ep_fifo_status,
1108 	.fifo_flush	= pxa25x_ep_fifo_flush,
1109 };
1110 
1111 
1112 /* ---------------------------------------------------------------------------
1113  *	device-scoped parts of the api to the usb controller hardware
1114  * ---------------------------------------------------------------------------
1115  */
1116 
1117 static int pxa25x_udc_get_frame(struct usb_gadget *_gadget)
1118 {
1119 	struct pxa25x_udc	*dev;
1120 
1121 	dev = container_of(_gadget, struct pxa25x_udc, gadget);
1122 	return ((udc_get_reg(dev, UFNRH) & 0x07) << 8) |
1123 		(udc_get_reg(dev, UFNRL) & 0xff);
1124 }
1125 
1126 static int pxa25x_udc_wakeup(struct usb_gadget *_gadget)
1127 {
1128 	struct pxa25x_udc	*udc;
1129 
1130 	udc = container_of(_gadget, struct pxa25x_udc, gadget);
1131 
1132 	/* host may not have enabled remote wakeup */
1133 	if ((udc_ep0_get_UDCCS(udc) & UDCCS0_DRWF) == 0)
1134 		return -EHOSTUNREACH;
1135 	udc_set_mask_UDCCR(udc, UDCCR_RSM);
1136 	return 0;
1137 }
1138 
1139 static void stop_activity(struct pxa25x_udc *, struct usb_gadget_driver *);
1140 static void udc_enable (struct pxa25x_udc *);
1141 static void udc_disable(struct pxa25x_udc *);
1142 
1143 /* We disable the UDC -- and its 48 MHz clock -- whenever it's not
1144  * in active use.
1145  */
1146 static int pullup(struct pxa25x_udc *udc)
1147 {
1148 	int is_active = udc->vbus && udc->pullup && !udc->suspended;
1149 	DMSG("%s\n", is_active ? "active" : "inactive");
1150 	if (is_active) {
1151 		if (!udc->active) {
1152 			udc->active = 1;
1153 			/* Enable clock for USB device */
1154 			clk_enable(udc->clk);
1155 			udc_enable(udc);
1156 		}
1157 	} else {
1158 		if (udc->active) {
1159 			if (udc->gadget.speed != USB_SPEED_UNKNOWN) {
1160 				DMSG("disconnect %s\n", udc->driver
1161 					? udc->driver->driver.name
1162 					: "(no driver)");
1163 				stop_activity(udc, udc->driver);
1164 			}
1165 			udc_disable(udc);
1166 			/* Disable clock for USB device */
1167 			clk_disable(udc->clk);
1168 			udc->active = 0;
1169 		}
1170 
1171 	}
1172 	return 0;
1173 }
1174 
1175 /* VBUS reporting logically comes from a transceiver */
1176 static int pxa25x_udc_vbus_session(struct usb_gadget *_gadget, int is_active)
1177 {
1178 	struct pxa25x_udc	*udc;
1179 
1180 	udc = container_of(_gadget, struct pxa25x_udc, gadget);
1181 	udc->vbus = is_active;
1182 	DMSG("vbus %s\n", is_active ? "supplied" : "inactive");
1183 	pullup(udc);
1184 	return 0;
1185 }
1186 
1187 /* drivers may have software control over D+ pullup */
1188 static int pxa25x_udc_pullup(struct usb_gadget *_gadget, int is_active)
1189 {
1190 	struct pxa25x_udc	*udc;
1191 
1192 	udc = container_of(_gadget, struct pxa25x_udc, gadget);
1193 
1194 	/* not all boards support pullup control */
1195 	if (!gpio_is_valid(udc->mach->gpio_pullup) && !udc->mach->udc_command)
1196 		return -EOPNOTSUPP;
1197 
1198 	udc->pullup = (is_active != 0);
1199 	pullup(udc);
1200 	return 0;
1201 }
1202 
1203 /* boards may consume current from VBUS, up to 100-500mA based on config.
1204  * the 500uA suspend ceiling means that exclusively vbus-powered PXA designs
1205  * violate USB specs.
1206  */
1207 static int pxa25x_udc_vbus_draw(struct usb_gadget *_gadget, unsigned mA)
1208 {
1209 	struct pxa25x_udc	*udc;
1210 
1211 	udc = container_of(_gadget, struct pxa25x_udc, gadget);
1212 
1213 	if (!IS_ERR_OR_NULL(udc->transceiver))
1214 		return usb_phy_set_power(udc->transceiver, mA);
1215 	return -EOPNOTSUPP;
1216 }
1217 
1218 static int pxa25x_udc_start(struct usb_gadget *g,
1219 		struct usb_gadget_driver *driver);
1220 static int pxa25x_udc_stop(struct usb_gadget *g);
1221 
1222 static const struct usb_gadget_ops pxa25x_udc_ops = {
1223 	.get_frame	= pxa25x_udc_get_frame,
1224 	.wakeup		= pxa25x_udc_wakeup,
1225 	.vbus_session	= pxa25x_udc_vbus_session,
1226 	.pullup		= pxa25x_udc_pullup,
1227 	.vbus_draw	= pxa25x_udc_vbus_draw,
1228 	.udc_start	= pxa25x_udc_start,
1229 	.udc_stop	= pxa25x_udc_stop,
1230 };
1231 
1232 /*-------------------------------------------------------------------------*/
1233 
1234 #ifdef CONFIG_USB_GADGET_DEBUG_FS
1235 
1236 static int udc_debug_show(struct seq_file *m, void *_d)
1237 {
1238 	struct pxa25x_udc	*dev = m->private;
1239 	unsigned long		flags;
1240 	int			i;
1241 	u32			tmp;
1242 
1243 	local_irq_save(flags);
1244 
1245 	/* basic device status */
1246 	seq_printf(m, DRIVER_DESC "\n"
1247 		"%s version: %s\nGadget driver: %s\nHost %s\n\n",
1248 		driver_name, DRIVER_VERSION SIZE_STR "(pio)",
1249 		dev->driver ? dev->driver->driver.name : "(none)",
1250 		dev->gadget.speed == USB_SPEED_FULL ? "full speed" : "disconnected");
1251 
1252 	/* registers for device and ep0 */
1253 	seq_printf(m,
1254 		"uicr %02X.%02X, usir %02X.%02x, ufnr %02X.%02X\n",
1255 		udc_get_reg(dev, UICR1), udc_get_reg(dev, UICR0),
1256 		udc_get_reg(dev, USIR1), udc_get_reg(dev, USIR0),
1257 		udc_get_reg(dev, UFNRH), udc_get_reg(dev, UFNRL));
1258 
1259 	tmp = udc_get_reg(dev, UDCCR);
1260 	seq_printf(m,
1261 		"udccr %02X =%s%s%s%s%s%s%s%s\n", tmp,
1262 		(tmp & UDCCR_REM) ? " rem" : "",
1263 		(tmp & UDCCR_RSTIR) ? " rstir" : "",
1264 		(tmp & UDCCR_SRM) ? " srm" : "",
1265 		(tmp & UDCCR_SUSIR) ? " susir" : "",
1266 		(tmp & UDCCR_RESIR) ? " resir" : "",
1267 		(tmp & UDCCR_RSM) ? " rsm" : "",
1268 		(tmp & UDCCR_UDA) ? " uda" : "",
1269 		(tmp & UDCCR_UDE) ? " ude" : "");
1270 
1271 	tmp = udc_ep0_get_UDCCS(dev);
1272 	seq_printf(m,
1273 		"udccs0 %02X =%s%s%s%s%s%s%s%s\n", tmp,
1274 		(tmp & UDCCS0_SA) ? " sa" : "",
1275 		(tmp & UDCCS0_RNE) ? " rne" : "",
1276 		(tmp & UDCCS0_FST) ? " fst" : "",
1277 		(tmp & UDCCS0_SST) ? " sst" : "",
1278 		(tmp & UDCCS0_DRWF) ? " dwrf" : "",
1279 		(tmp & UDCCS0_FTF) ? " ftf" : "",
1280 		(tmp & UDCCS0_IPR) ? " ipr" : "",
1281 		(tmp & UDCCS0_OPR) ? " opr" : "");
1282 
1283 	if (dev->has_cfr) {
1284 		tmp = udc_get_reg(dev, UDCCFR);
1285 		seq_printf(m,
1286 			"udccfr %02X =%s%s\n", tmp,
1287 			(tmp & UDCCFR_AREN) ? " aren" : "",
1288 			(tmp & UDCCFR_ACM) ? " acm" : "");
1289 	}
1290 
1291 	if (dev->gadget.speed != USB_SPEED_FULL || !dev->driver)
1292 		goto done;
1293 
1294 	seq_printf(m, "ep0 IN %lu/%lu, OUT %lu/%lu\nirqs %lu\n\n",
1295 		dev->stats.write.bytes, dev->stats.write.ops,
1296 		dev->stats.read.bytes, dev->stats.read.ops,
1297 		dev->stats.irqs);
1298 
1299 	/* dump endpoint queues */
1300 	for (i = 0; i < PXA_UDC_NUM_ENDPOINTS; i++) {
1301 		struct pxa25x_ep	*ep = &dev->ep [i];
1302 		struct pxa25x_request	*req;
1303 
1304 		if (i != 0) {
1305 			const struct usb_endpoint_descriptor	*desc;
1306 
1307 			desc = ep->ep.desc;
1308 			if (!desc)
1309 				continue;
1310 			tmp = udc_ep_get_UDCCS(&dev->ep[i]);
1311 			seq_printf(m,
1312 				"%s max %d %s udccs %02x irqs %lu\n",
1313 				ep->ep.name, usb_endpoint_maxp(desc),
1314 				"pio", tmp, ep->pio_irqs);
1315 			/* TODO translate all five groups of udccs bits! */
1316 
1317 		} else /* ep0 should only have one transfer queued */
1318 			seq_printf(m, "ep0 max 16 pio irqs %lu\n",
1319 				ep->pio_irqs);
1320 
1321 		if (list_empty(&ep->queue)) {
1322 			seq_printf(m, "\t(nothing queued)\n");
1323 			continue;
1324 		}
1325 		list_for_each_entry(req, &ep->queue, queue) {
1326 			seq_printf(m,
1327 					"\treq %p len %d/%d buf %p\n",
1328 					&req->req, req->req.actual,
1329 					req->req.length, req->req.buf);
1330 		}
1331 	}
1332 
1333 done:
1334 	local_irq_restore(flags);
1335 	return 0;
1336 }
1337 DEFINE_SHOW_ATTRIBUTE(udc_debug);
1338 
1339 #define create_debug_files(dev) \
1340 	do { \
1341 		dev->debugfs_udc = debugfs_create_file(dev->gadget.name, \
1342 			S_IRUGO, NULL, dev, &udc_debug_fops); \
1343 	} while (0)
1344 #define remove_debug_files(dev) debugfs_remove(dev->debugfs_udc)
1345 
1346 #else	/* !CONFIG_USB_GADGET_DEBUG_FILES */
1347 
1348 #define create_debug_files(dev) do {} while (0)
1349 #define remove_debug_files(dev) do {} while (0)
1350 
1351 #endif	/* CONFIG_USB_GADGET_DEBUG_FILES */
1352 
1353 /*-------------------------------------------------------------------------*/
1354 
1355 /*
1356  *	udc_disable - disable USB device controller
1357  */
1358 static void udc_disable(struct pxa25x_udc *dev)
1359 {
1360 	/* block all irqs */
1361 	udc_set_mask_UDCCR(dev, UDCCR_SRM|UDCCR_REM);
1362 	udc_set_reg(dev, UICR0, 0xff);
1363 	udc_set_reg(dev, UICR1, 0xff);
1364 	udc_set_reg(dev, UFNRH, UFNRH_SIM);
1365 
1366 	/* if hardware supports it, disconnect from usb */
1367 	pullup_off();
1368 
1369 	udc_clear_mask_UDCCR(dev, UDCCR_UDE);
1370 
1371 	ep0_idle (dev);
1372 	dev->gadget.speed = USB_SPEED_UNKNOWN;
1373 }
1374 
1375 
1376 /*
1377  *	udc_reinit - initialize software state
1378  */
1379 static void udc_reinit(struct pxa25x_udc *dev)
1380 {
1381 	u32	i;
1382 
1383 	/* device/ep0 records init */
1384 	INIT_LIST_HEAD (&dev->gadget.ep_list);
1385 	INIT_LIST_HEAD (&dev->gadget.ep0->ep_list);
1386 	dev->ep0state = EP0_IDLE;
1387 	dev->gadget.quirk_altset_not_supp = 1;
1388 
1389 	/* basic endpoint records init */
1390 	for (i = 0; i < PXA_UDC_NUM_ENDPOINTS; i++) {
1391 		struct pxa25x_ep *ep = &dev->ep[i];
1392 
1393 		if (i != 0)
1394 			list_add_tail (&ep->ep.ep_list, &dev->gadget.ep_list);
1395 
1396 		ep->ep.desc = NULL;
1397 		ep->stopped = 0;
1398 		INIT_LIST_HEAD (&ep->queue);
1399 		ep->pio_irqs = 0;
1400 		usb_ep_set_maxpacket_limit(&ep->ep, ep->ep.maxpacket);
1401 	}
1402 
1403 	/* the rest was statically initialized, and is read-only */
1404 }
1405 
1406 /* until it's enabled, this UDC should be completely invisible
1407  * to any USB host.
1408  */
1409 static void udc_enable (struct pxa25x_udc *dev)
1410 {
1411 	udc_clear_mask_UDCCR(dev, UDCCR_UDE);
1412 
1413 	/* try to clear these bits before we enable the udc */
1414 	udc_ack_int_UDCCR(dev, UDCCR_SUSIR|/*UDCCR_RSTIR|*/UDCCR_RESIR);
1415 
1416 	ep0_idle(dev);
1417 	dev->gadget.speed = USB_SPEED_UNKNOWN;
1418 	dev->stats.irqs = 0;
1419 
1420 	/*
1421 	 * sequence taken from chapter 12.5.10, PXA250 AppProcDevManual:
1422 	 * - enable UDC
1423 	 * - if RESET is already in progress, ack interrupt
1424 	 * - unmask reset interrupt
1425 	 */
1426 	udc_set_mask_UDCCR(dev, UDCCR_UDE);
1427 	if (!(udc_get_reg(dev, UDCCR) & UDCCR_UDA))
1428 		udc_ack_int_UDCCR(dev, UDCCR_RSTIR);
1429 
1430 	if (dev->has_cfr /* UDC_RES2 is defined */) {
1431 		/* pxa255 (a0+) can avoid a set_config race that could
1432 		 * prevent gadget drivers from configuring correctly
1433 		 */
1434 		udc_set_reg(dev, UDCCFR, UDCCFR_ACM | UDCCFR_MB1);
1435 	} else {
1436 		/* "USB test mode" for pxa250 errata 40-42 (stepping a0, a1)
1437 		 * which could result in missing packets and interrupts.
1438 		 * supposedly one bit per endpoint, controlling whether it
1439 		 * double buffers or not; ACM/AREN bits fit into the holes.
1440 		 * zero bits (like USIR0_IRx) disable double buffering.
1441 		 */
1442 		udc_set_reg(dev, UDC_RES1, 0x00);
1443 		udc_set_reg(dev, UDC_RES2, 0x00);
1444 	}
1445 
1446 	/* enable suspend/resume and reset irqs */
1447 	udc_clear_mask_UDCCR(dev, UDCCR_SRM | UDCCR_REM);
1448 
1449 	/* enable ep0 irqs */
1450 	udc_set_reg(dev, UICR0, udc_get_reg(dev, UICR0) & ~UICR0_IM0);
1451 
1452 	/* if hardware supports it, pullup D+ and wait for reset */
1453 	pullup_on();
1454 }
1455 
1456 
1457 /* when a driver is successfully registered, it will receive
1458  * control requests including set_configuration(), which enables
1459  * non-control requests.  then usb traffic follows until a
1460  * disconnect is reported.  then a host may connect again, or
1461  * the driver might get unbound.
1462  */
1463 static int pxa25x_udc_start(struct usb_gadget *g,
1464 		struct usb_gadget_driver *driver)
1465 {
1466 	struct pxa25x_udc	*dev = to_pxa25x(g);
1467 	int			retval;
1468 
1469 	/* first hook up the driver ... */
1470 	dev->driver = driver;
1471 	dev->pullup = 1;
1472 
1473 	/* ... then enable host detection and ep0; and we're ready
1474 	 * for set_configuration as well as eventual disconnect.
1475 	 */
1476 	/* connect to bus through transceiver */
1477 	if (!IS_ERR_OR_NULL(dev->transceiver)) {
1478 		retval = otg_set_peripheral(dev->transceiver->otg,
1479 						&dev->gadget);
1480 		if (retval)
1481 			goto bind_fail;
1482 	}
1483 
1484 	dump_state(dev);
1485 	return 0;
1486 bind_fail:
1487 	return retval;
1488 }
1489 
1490 static void
1491 reset_gadget(struct pxa25x_udc *dev, struct usb_gadget_driver *driver)
1492 {
1493 	int i;
1494 
1495 	/* don't disconnect drivers more than once */
1496 	if (dev->gadget.speed == USB_SPEED_UNKNOWN)
1497 		driver = NULL;
1498 	dev->gadget.speed = USB_SPEED_UNKNOWN;
1499 
1500 	/* prevent new request submissions, kill any outstanding requests  */
1501 	for (i = 0; i < PXA_UDC_NUM_ENDPOINTS; i++) {
1502 		struct pxa25x_ep *ep = &dev->ep[i];
1503 
1504 		ep->stopped = 1;
1505 		nuke(ep, -ESHUTDOWN);
1506 	}
1507 	del_timer_sync(&dev->timer);
1508 
1509 	/* report reset; the driver is already quiesced */
1510 	if (driver)
1511 		usb_gadget_udc_reset(&dev->gadget, driver);
1512 
1513 	/* re-init driver-visible data structures */
1514 	udc_reinit(dev);
1515 }
1516 
1517 static void
1518 stop_activity(struct pxa25x_udc *dev, struct usb_gadget_driver *driver)
1519 {
1520 	int i;
1521 
1522 	/* don't disconnect drivers more than once */
1523 	if (dev->gadget.speed == USB_SPEED_UNKNOWN)
1524 		driver = NULL;
1525 	dev->gadget.speed = USB_SPEED_UNKNOWN;
1526 
1527 	/* prevent new request submissions, kill any outstanding requests  */
1528 	for (i = 0; i < PXA_UDC_NUM_ENDPOINTS; i++) {
1529 		struct pxa25x_ep *ep = &dev->ep[i];
1530 
1531 		ep->stopped = 1;
1532 		nuke(ep, -ESHUTDOWN);
1533 	}
1534 	del_timer_sync(&dev->timer);
1535 
1536 	/* report disconnect; the driver is already quiesced */
1537 	if (driver)
1538 		driver->disconnect(&dev->gadget);
1539 
1540 	/* re-init driver-visible data structures */
1541 	udc_reinit(dev);
1542 }
1543 
1544 static int pxa25x_udc_stop(struct usb_gadget*g)
1545 {
1546 	struct pxa25x_udc	*dev = to_pxa25x(g);
1547 
1548 	local_irq_disable();
1549 	dev->pullup = 0;
1550 	stop_activity(dev, NULL);
1551 	local_irq_enable();
1552 
1553 	if (!IS_ERR_OR_NULL(dev->transceiver))
1554 		(void) otg_set_peripheral(dev->transceiver->otg, NULL);
1555 
1556 	dev->driver = NULL;
1557 
1558 	dump_state(dev);
1559 
1560 	return 0;
1561 }
1562 
1563 /*-------------------------------------------------------------------------*/
1564 
1565 #ifdef CONFIG_ARCH_LUBBOCK
1566 
1567 /* Lubbock has separate connect and disconnect irqs.  More typical designs
1568  * use one GPIO as the VBUS IRQ, and another to control the D+ pullup.
1569  */
1570 
1571 static irqreturn_t
1572 lubbock_vbus_irq(int irq, void *_dev)
1573 {
1574 	struct pxa25x_udc	*dev = _dev;
1575 	int			vbus;
1576 
1577 	dev->stats.irqs++;
1578 	switch (irq) {
1579 	case LUBBOCK_USB_IRQ:
1580 		vbus = 1;
1581 		disable_irq(LUBBOCK_USB_IRQ);
1582 		enable_irq(LUBBOCK_USB_DISC_IRQ);
1583 		break;
1584 	case LUBBOCK_USB_DISC_IRQ:
1585 		vbus = 0;
1586 		disable_irq(LUBBOCK_USB_DISC_IRQ);
1587 		enable_irq(LUBBOCK_USB_IRQ);
1588 		break;
1589 	default:
1590 		return IRQ_NONE;
1591 	}
1592 
1593 	pxa25x_udc_vbus_session(&dev->gadget, vbus);
1594 	return IRQ_HANDLED;
1595 }
1596 
1597 #endif
1598 
1599 
1600 /*-------------------------------------------------------------------------*/
1601 
1602 static inline void clear_ep_state (struct pxa25x_udc *dev)
1603 {
1604 	unsigned i;
1605 
1606 	/* hardware SET_{CONFIGURATION,INTERFACE} automagic resets endpoint
1607 	 * fifos, and pending transactions mustn't be continued in any case.
1608 	 */
1609 	for (i = 1; i < PXA_UDC_NUM_ENDPOINTS; i++)
1610 		nuke(&dev->ep[i], -ECONNABORTED);
1611 }
1612 
1613 static void udc_watchdog(struct timer_list *t)
1614 {
1615 	struct pxa25x_udc	*dev = from_timer(dev, t, timer);
1616 
1617 	local_irq_disable();
1618 	if (dev->ep0state == EP0_STALL
1619 			&& (udc_ep0_get_UDCCS(dev) & UDCCS0_FST) == 0
1620 			&& (udc_ep0_get_UDCCS(dev) & UDCCS0_SST) == 0) {
1621 		udc_ep0_set_UDCCS(dev, UDCCS0_FST|UDCCS0_FTF);
1622 		DBG(DBG_VERBOSE, "ep0 re-stall\n");
1623 		start_watchdog(dev);
1624 	}
1625 	local_irq_enable();
1626 }
1627 
1628 static void handle_ep0 (struct pxa25x_udc *dev)
1629 {
1630 	u32			udccs0 = udc_ep0_get_UDCCS(dev);
1631 	struct pxa25x_ep	*ep = &dev->ep [0];
1632 	struct pxa25x_request	*req;
1633 	union {
1634 		struct usb_ctrlrequest	r;
1635 		u8			raw [8];
1636 		u32			word [2];
1637 	} u;
1638 
1639 	if (list_empty(&ep->queue))
1640 		req = NULL;
1641 	else
1642 		req = list_entry(ep->queue.next, struct pxa25x_request, queue);
1643 
1644 	/* clear stall status */
1645 	if (udccs0 & UDCCS0_SST) {
1646 		nuke(ep, -EPIPE);
1647 		udc_ep0_set_UDCCS(dev, UDCCS0_SST);
1648 		del_timer(&dev->timer);
1649 		ep0_idle(dev);
1650 	}
1651 
1652 	/* previous request unfinished?  non-error iff back-to-back ... */
1653 	if ((udccs0 & UDCCS0_SA) != 0 && dev->ep0state != EP0_IDLE) {
1654 		nuke(ep, 0);
1655 		del_timer(&dev->timer);
1656 		ep0_idle(dev);
1657 	}
1658 
1659 	switch (dev->ep0state) {
1660 	case EP0_IDLE:
1661 		/* late-breaking status? */
1662 		udccs0 = udc_ep0_get_UDCCS(dev);
1663 
1664 		/* start control request? */
1665 		if (likely((udccs0 & (UDCCS0_OPR|UDCCS0_SA|UDCCS0_RNE))
1666 				== (UDCCS0_OPR|UDCCS0_SA|UDCCS0_RNE))) {
1667 			int i;
1668 
1669 			nuke (ep, -EPROTO);
1670 
1671 			/* read SETUP packet */
1672 			for (i = 0; i < 8; i++) {
1673 				if (unlikely(!(udc_ep0_get_UDCCS(dev) & UDCCS0_RNE))) {
1674 bad_setup:
1675 					DMSG("SETUP %d!\n", i);
1676 					goto stall;
1677 				}
1678 				u.raw [i] = (u8) UDDR0;
1679 			}
1680 			if (unlikely((udc_ep0_get_UDCCS(dev) & UDCCS0_RNE) != 0))
1681 				goto bad_setup;
1682 
1683 got_setup:
1684 			DBG(DBG_VERBOSE, "SETUP %02x.%02x v%04x i%04x l%04x\n",
1685 				u.r.bRequestType, u.r.bRequest,
1686 				le16_to_cpu(u.r.wValue),
1687 				le16_to_cpu(u.r.wIndex),
1688 				le16_to_cpu(u.r.wLength));
1689 
1690 			/* cope with automagic for some standard requests. */
1691 			dev->req_std = (u.r.bRequestType & USB_TYPE_MASK)
1692 						== USB_TYPE_STANDARD;
1693 			dev->req_config = 0;
1694 			dev->req_pending = 1;
1695 			switch (u.r.bRequest) {
1696 			/* hardware restricts gadget drivers here! */
1697 			case USB_REQ_SET_CONFIGURATION:
1698 				if (u.r.bRequestType == USB_RECIP_DEVICE) {
1699 					/* reflect hardware's automagic
1700 					 * up to the gadget driver.
1701 					 */
1702 config_change:
1703 					dev->req_config = 1;
1704 					clear_ep_state(dev);
1705 					/* if !has_cfr, there's no synch
1706 					 * else use AREN (later) not SA|OPR
1707 					 * USIR0_IR0 acts edge sensitive
1708 					 */
1709 				}
1710 				break;
1711 			/* ... and here, even more ... */
1712 			case USB_REQ_SET_INTERFACE:
1713 				if (u.r.bRequestType == USB_RECIP_INTERFACE) {
1714 					/* udc hardware is broken by design:
1715 					 *  - altsetting may only be zero;
1716 					 *  - hw resets all interfaces' eps;
1717 					 *  - ep reset doesn't include halt(?).
1718 					 */
1719 					DMSG("broken set_interface (%d/%d)\n",
1720 						le16_to_cpu(u.r.wIndex),
1721 						le16_to_cpu(u.r.wValue));
1722 					goto config_change;
1723 				}
1724 				break;
1725 			/* hardware was supposed to hide this */
1726 			case USB_REQ_SET_ADDRESS:
1727 				if (u.r.bRequestType == USB_RECIP_DEVICE) {
1728 					ep0start(dev, 0, "address");
1729 					return;
1730 				}
1731 				break;
1732 			}
1733 
1734 			if (u.r.bRequestType & USB_DIR_IN)
1735 				dev->ep0state = EP0_IN_DATA_PHASE;
1736 			else
1737 				dev->ep0state = EP0_OUT_DATA_PHASE;
1738 
1739 			i = dev->driver->setup(&dev->gadget, &u.r);
1740 			if (i < 0) {
1741 				/* hardware automagic preventing STALL... */
1742 				if (dev->req_config) {
1743 					/* hardware sometimes neglects to tell
1744 					 * tell us about config change events,
1745 					 * so later ones may fail...
1746 					 */
1747 					WARNING("config change %02x fail %d?\n",
1748 						u.r.bRequest, i);
1749 					return;
1750 					/* TODO experiment:  if has_cfr,
1751 					 * hardware didn't ACK; maybe we
1752 					 * could actually STALL!
1753 					 */
1754 				}
1755 				DBG(DBG_VERBOSE, "protocol STALL, "
1756 					"%02x err %d\n", udc_ep0_get_UDCCS(dev), i);
1757 stall:
1758 				/* the watchdog timer helps deal with cases
1759 				 * where udc seems to clear FST wrongly, and
1760 				 * then NAKs instead of STALLing.
1761 				 */
1762 				ep0start(dev, UDCCS0_FST|UDCCS0_FTF, "stall");
1763 				start_watchdog(dev);
1764 				dev->ep0state = EP0_STALL;
1765 
1766 			/* deferred i/o == no response yet */
1767 			} else if (dev->req_pending) {
1768 				if (likely(dev->ep0state == EP0_IN_DATA_PHASE
1769 						|| dev->req_std || u.r.wLength))
1770 					ep0start(dev, 0, "defer");
1771 				else
1772 					ep0start(dev, UDCCS0_IPR, "defer/IPR");
1773 			}
1774 
1775 			/* expect at least one data or status stage irq */
1776 			return;
1777 
1778 		} else if (likely((udccs0 & (UDCCS0_OPR|UDCCS0_SA))
1779 				== (UDCCS0_OPR|UDCCS0_SA))) {
1780 			unsigned i;
1781 
1782 			/* pxa210/250 erratum 131 for B0/B1 says RNE lies.
1783 			 * still observed on a pxa255 a0.
1784 			 */
1785 			DBG(DBG_VERBOSE, "e131\n");
1786 			nuke(ep, -EPROTO);
1787 
1788 			/* read SETUP data, but don't trust it too much */
1789 			for (i = 0; i < 8; i++)
1790 				u.raw [i] = (u8) UDDR0;
1791 			if ((u.r.bRequestType & USB_RECIP_MASK)
1792 					> USB_RECIP_OTHER)
1793 				goto stall;
1794 			if (u.word [0] == 0 && u.word [1] == 0)
1795 				goto stall;
1796 			goto got_setup;
1797 		} else {
1798 			/* some random early IRQ:
1799 			 * - we acked FST
1800 			 * - IPR cleared
1801 			 * - OPR got set, without SA (likely status stage)
1802 			 */
1803 			udc_ep0_set_UDCCS(dev, udccs0 & (UDCCS0_SA|UDCCS0_OPR));
1804 		}
1805 		break;
1806 	case EP0_IN_DATA_PHASE:			/* GET_DESCRIPTOR etc */
1807 		if (udccs0 & UDCCS0_OPR) {
1808 			udc_ep0_set_UDCCS(dev, UDCCS0_OPR|UDCCS0_FTF);
1809 			DBG(DBG_VERBOSE, "ep0in premature status\n");
1810 			if (req)
1811 				done(ep, req, 0);
1812 			ep0_idle(dev);
1813 		} else /* irq was IPR clearing */ {
1814 			if (req) {
1815 				/* this IN packet might finish the request */
1816 				(void) write_ep0_fifo(ep, req);
1817 			} /* else IN token before response was written */
1818 		}
1819 		break;
1820 	case EP0_OUT_DATA_PHASE:		/* SET_DESCRIPTOR etc */
1821 		if (udccs0 & UDCCS0_OPR) {
1822 			if (req) {
1823 				/* this OUT packet might finish the request */
1824 				if (read_ep0_fifo(ep, req))
1825 					done(ep, req, 0);
1826 				/* else more OUT packets expected */
1827 			} /* else OUT token before read was issued */
1828 		} else /* irq was IPR clearing */ {
1829 			DBG(DBG_VERBOSE, "ep0out premature status\n");
1830 			if (req)
1831 				done(ep, req, 0);
1832 			ep0_idle(dev);
1833 		}
1834 		break;
1835 	case EP0_END_XFER:
1836 		if (req)
1837 			done(ep, req, 0);
1838 		/* ack control-IN status (maybe in-zlp was skipped)
1839 		 * also appears after some config change events.
1840 		 */
1841 		if (udccs0 & UDCCS0_OPR)
1842 			udc_ep0_set_UDCCS(dev, UDCCS0_OPR);
1843 		ep0_idle(dev);
1844 		break;
1845 	case EP0_STALL:
1846 		udc_ep0_set_UDCCS(dev, UDCCS0_FST);
1847 		break;
1848 	}
1849 	udc_set_reg(dev, USIR0, USIR0_IR0);
1850 }
1851 
1852 static void handle_ep(struct pxa25x_ep *ep)
1853 {
1854 	struct pxa25x_request	*req;
1855 	int			is_in = ep->bEndpointAddress & USB_DIR_IN;
1856 	int			completed;
1857 	u32			udccs, tmp;
1858 
1859 	do {
1860 		completed = 0;
1861 		if (likely (!list_empty(&ep->queue)))
1862 			req = list_entry(ep->queue.next,
1863 					struct pxa25x_request, queue);
1864 		else
1865 			req = NULL;
1866 
1867 		// TODO check FST handling
1868 
1869 		udccs = udc_ep_get_UDCCS(ep);
1870 		if (unlikely(is_in)) {	/* irq from TPC, SST, or (ISO) TUR */
1871 			tmp = UDCCS_BI_TUR;
1872 			if (likely(ep->bmAttributes == USB_ENDPOINT_XFER_BULK))
1873 				tmp |= UDCCS_BI_SST;
1874 			tmp &= udccs;
1875 			if (likely (tmp))
1876 				udc_ep_set_UDCCS(ep, tmp);
1877 			if (req && likely ((udccs & UDCCS_BI_TFS) != 0))
1878 				completed = write_fifo(ep, req);
1879 
1880 		} else {	/* irq from RPC (or for ISO, ROF) */
1881 			if (likely(ep->bmAttributes == USB_ENDPOINT_XFER_BULK))
1882 				tmp = UDCCS_BO_SST | UDCCS_BO_DME;
1883 			else
1884 				tmp = UDCCS_IO_ROF | UDCCS_IO_DME;
1885 			tmp &= udccs;
1886 			if (likely(tmp))
1887 				udc_ep_set_UDCCS(ep, tmp);
1888 
1889 			/* fifos can hold packets, ready for reading... */
1890 			if (likely(req)) {
1891 				completed = read_fifo(ep, req);
1892 			} else
1893 				pio_irq_disable(ep);
1894 		}
1895 		ep->pio_irqs++;
1896 	} while (completed);
1897 }
1898 
1899 /*
1900  *	pxa25x_udc_irq - interrupt handler
1901  *
1902  * avoid delays in ep0 processing. the control handshaking isn't always
1903  * under software control (pxa250c0 and the pxa255 are better), and delays
1904  * could cause usb protocol errors.
1905  */
1906 static irqreturn_t
1907 pxa25x_udc_irq(int irq, void *_dev)
1908 {
1909 	struct pxa25x_udc	*dev = _dev;
1910 	int			handled;
1911 
1912 	dev->stats.irqs++;
1913 	do {
1914 		u32		udccr = udc_get_reg(dev, UDCCR);
1915 
1916 		handled = 0;
1917 
1918 		/* SUSpend Interrupt Request */
1919 		if (unlikely(udccr & UDCCR_SUSIR)) {
1920 			udc_ack_int_UDCCR(dev, UDCCR_SUSIR);
1921 			handled = 1;
1922 			DBG(DBG_VERBOSE, "USB suspend\n");
1923 
1924 			if (dev->gadget.speed != USB_SPEED_UNKNOWN
1925 					&& dev->driver
1926 					&& dev->driver->suspend)
1927 				dev->driver->suspend(&dev->gadget);
1928 			ep0_idle (dev);
1929 		}
1930 
1931 		/* RESume Interrupt Request */
1932 		if (unlikely(udccr & UDCCR_RESIR)) {
1933 			udc_ack_int_UDCCR(dev, UDCCR_RESIR);
1934 			handled = 1;
1935 			DBG(DBG_VERBOSE, "USB resume\n");
1936 
1937 			if (dev->gadget.speed != USB_SPEED_UNKNOWN
1938 					&& dev->driver
1939 					&& dev->driver->resume)
1940 				dev->driver->resume(&dev->gadget);
1941 		}
1942 
1943 		/* ReSeT Interrupt Request - USB reset */
1944 		if (unlikely(udccr & UDCCR_RSTIR)) {
1945 			udc_ack_int_UDCCR(dev, UDCCR_RSTIR);
1946 			handled = 1;
1947 
1948 			if ((udc_get_reg(dev, UDCCR) & UDCCR_UDA) == 0) {
1949 				DBG(DBG_VERBOSE, "USB reset start\n");
1950 
1951 				/* reset driver and endpoints,
1952 				 * in case that's not yet done
1953 				 */
1954 				reset_gadget(dev, dev->driver);
1955 
1956 			} else {
1957 				DBG(DBG_VERBOSE, "USB reset end\n");
1958 				dev->gadget.speed = USB_SPEED_FULL;
1959 				memset(&dev->stats, 0, sizeof dev->stats);
1960 				/* driver and endpoints are still reset */
1961 			}
1962 
1963 		} else {
1964 			u32	usir0 = udc_get_reg(dev, USIR0) &
1965 					~udc_get_reg(dev, UICR0);
1966 			u32	usir1 = udc_get_reg(dev, USIR1) &
1967 					~udc_get_reg(dev, UICR1);
1968 			int	i;
1969 
1970 			if (unlikely (!usir0 && !usir1))
1971 				continue;
1972 
1973 			DBG(DBG_VERY_NOISY, "irq %02x.%02x\n", usir1, usir0);
1974 
1975 			/* control traffic */
1976 			if (usir0 & USIR0_IR0) {
1977 				dev->ep[0].pio_irqs++;
1978 				handle_ep0(dev);
1979 				handled = 1;
1980 			}
1981 
1982 			/* endpoint data transfers */
1983 			for (i = 0; i < 8; i++) {
1984 				u32	tmp = 1 << i;
1985 
1986 				if (i && (usir0 & tmp)) {
1987 					handle_ep(&dev->ep[i]);
1988 					udc_set_reg(dev, USIR0,
1989 						udc_get_reg(dev, USIR0) | tmp);
1990 					handled = 1;
1991 				}
1992 #ifndef	CONFIG_USB_PXA25X_SMALL
1993 				if (usir1 & tmp) {
1994 					handle_ep(&dev->ep[i+8]);
1995 					udc_set_reg(dev, USIR1,
1996 						udc_get_reg(dev, USIR1) | tmp);
1997 					handled = 1;
1998 				}
1999 #endif
2000 			}
2001 		}
2002 
2003 		/* we could also ask for 1 msec SOF (SIR) interrupts */
2004 
2005 	} while (handled);
2006 	return IRQ_HANDLED;
2007 }
2008 
2009 /*-------------------------------------------------------------------------*/
2010 
2011 static void nop_release (struct device *dev)
2012 {
2013 	DMSG("%s %s\n", __func__, dev_name(dev));
2014 }
2015 
2016 /* this uses load-time allocation and initialization (instead of
2017  * doing it at run-time) to save code, eliminate fault paths, and
2018  * be more obviously correct.
2019  */
2020 static struct pxa25x_udc memory = {
2021 	.gadget = {
2022 		.ops		= &pxa25x_udc_ops,
2023 		.ep0		= &memory.ep[0].ep,
2024 		.name		= driver_name,
2025 		.dev = {
2026 			.init_name	= "gadget",
2027 			.release	= nop_release,
2028 		},
2029 	},
2030 
2031 	/* control endpoint */
2032 	.ep[0] = {
2033 		.ep = {
2034 			.name		= ep0name,
2035 			.ops		= &pxa25x_ep_ops,
2036 			.maxpacket	= EP0_FIFO_SIZE,
2037 			.caps		= USB_EP_CAPS(USB_EP_CAPS_TYPE_CONTROL,
2038 						USB_EP_CAPS_DIR_ALL),
2039 		},
2040 		.dev		= &memory,
2041 		.regoff_udccs	= UDCCS0,
2042 		.regoff_uddr	= UDDR0,
2043 	},
2044 
2045 	/* first group of endpoints */
2046 	.ep[1] = {
2047 		.ep = {
2048 			.name		= "ep1in-bulk",
2049 			.ops		= &pxa25x_ep_ops,
2050 			.maxpacket	= BULK_FIFO_SIZE,
2051 			.caps		= USB_EP_CAPS(USB_EP_CAPS_TYPE_BULK,
2052 						USB_EP_CAPS_DIR_IN),
2053 		},
2054 		.dev		= &memory,
2055 		.fifo_size	= BULK_FIFO_SIZE,
2056 		.bEndpointAddress = USB_DIR_IN | 1,
2057 		.bmAttributes	= USB_ENDPOINT_XFER_BULK,
2058 		.regoff_udccs	= UDCCS1,
2059 		.regoff_uddr	= UDDR1,
2060 	},
2061 	.ep[2] = {
2062 		.ep = {
2063 			.name		= "ep2out-bulk",
2064 			.ops		= &pxa25x_ep_ops,
2065 			.maxpacket	= BULK_FIFO_SIZE,
2066 			.caps		= USB_EP_CAPS(USB_EP_CAPS_TYPE_BULK,
2067 						USB_EP_CAPS_DIR_OUT),
2068 		},
2069 		.dev		= &memory,
2070 		.fifo_size	= BULK_FIFO_SIZE,
2071 		.bEndpointAddress = 2,
2072 		.bmAttributes	= USB_ENDPOINT_XFER_BULK,
2073 		.regoff_udccs	= UDCCS2,
2074 		.regoff_ubcr	= UBCR2,
2075 		.regoff_uddr	= UDDR2,
2076 	},
2077 #ifndef CONFIG_USB_PXA25X_SMALL
2078 	.ep[3] = {
2079 		.ep = {
2080 			.name		= "ep3in-iso",
2081 			.ops		= &pxa25x_ep_ops,
2082 			.maxpacket	= ISO_FIFO_SIZE,
2083 			.caps		= USB_EP_CAPS(USB_EP_CAPS_TYPE_ISO,
2084 						USB_EP_CAPS_DIR_IN),
2085 		},
2086 		.dev		= &memory,
2087 		.fifo_size	= ISO_FIFO_SIZE,
2088 		.bEndpointAddress = USB_DIR_IN | 3,
2089 		.bmAttributes	= USB_ENDPOINT_XFER_ISOC,
2090 		.regoff_udccs	= UDCCS3,
2091 		.regoff_uddr	= UDDR3,
2092 	},
2093 	.ep[4] = {
2094 		.ep = {
2095 			.name		= "ep4out-iso",
2096 			.ops		= &pxa25x_ep_ops,
2097 			.maxpacket	= ISO_FIFO_SIZE,
2098 			.caps		= USB_EP_CAPS(USB_EP_CAPS_TYPE_ISO,
2099 						USB_EP_CAPS_DIR_OUT),
2100 		},
2101 		.dev		= &memory,
2102 		.fifo_size	= ISO_FIFO_SIZE,
2103 		.bEndpointAddress = 4,
2104 		.bmAttributes	= USB_ENDPOINT_XFER_ISOC,
2105 		.regoff_udccs	= UDCCS4,
2106 		.regoff_ubcr	= UBCR4,
2107 		.regoff_uddr	= UDDR4,
2108 	},
2109 	.ep[5] = {
2110 		.ep = {
2111 			.name		= "ep5in-int",
2112 			.ops		= &pxa25x_ep_ops,
2113 			.maxpacket	= INT_FIFO_SIZE,
2114 			.caps		= USB_EP_CAPS(0, 0),
2115 		},
2116 		.dev		= &memory,
2117 		.fifo_size	= INT_FIFO_SIZE,
2118 		.bEndpointAddress = USB_DIR_IN | 5,
2119 		.bmAttributes	= USB_ENDPOINT_XFER_INT,
2120 		.regoff_udccs	= UDCCS5,
2121 		.regoff_uddr	= UDDR5,
2122 	},
2123 
2124 	/* second group of endpoints */
2125 	.ep[6] = {
2126 		.ep = {
2127 			.name		= "ep6in-bulk",
2128 			.ops		= &pxa25x_ep_ops,
2129 			.maxpacket	= BULK_FIFO_SIZE,
2130 			.caps		= USB_EP_CAPS(USB_EP_CAPS_TYPE_BULK,
2131 						USB_EP_CAPS_DIR_IN),
2132 		},
2133 		.dev		= &memory,
2134 		.fifo_size	= BULK_FIFO_SIZE,
2135 		.bEndpointAddress = USB_DIR_IN | 6,
2136 		.bmAttributes	= USB_ENDPOINT_XFER_BULK,
2137 		.regoff_udccs	= UDCCS6,
2138 		.regoff_uddr	= UDDR6,
2139 	},
2140 	.ep[7] = {
2141 		.ep = {
2142 			.name		= "ep7out-bulk",
2143 			.ops		= &pxa25x_ep_ops,
2144 			.maxpacket	= BULK_FIFO_SIZE,
2145 			.caps		= USB_EP_CAPS(USB_EP_CAPS_TYPE_BULK,
2146 						USB_EP_CAPS_DIR_OUT),
2147 		},
2148 		.dev		= &memory,
2149 		.fifo_size	= BULK_FIFO_SIZE,
2150 		.bEndpointAddress = 7,
2151 		.bmAttributes	= USB_ENDPOINT_XFER_BULK,
2152 		.regoff_udccs	= UDCCS7,
2153 		.regoff_ubcr	= UBCR7,
2154 		.regoff_uddr	= UDDR7,
2155 	},
2156 	.ep[8] = {
2157 		.ep = {
2158 			.name		= "ep8in-iso",
2159 			.ops		= &pxa25x_ep_ops,
2160 			.maxpacket	= ISO_FIFO_SIZE,
2161 			.caps		= USB_EP_CAPS(USB_EP_CAPS_TYPE_ISO,
2162 						USB_EP_CAPS_DIR_IN),
2163 		},
2164 		.dev		= &memory,
2165 		.fifo_size	= ISO_FIFO_SIZE,
2166 		.bEndpointAddress = USB_DIR_IN | 8,
2167 		.bmAttributes	= USB_ENDPOINT_XFER_ISOC,
2168 		.regoff_udccs	= UDCCS8,
2169 		.regoff_uddr	= UDDR8,
2170 	},
2171 	.ep[9] = {
2172 		.ep = {
2173 			.name		= "ep9out-iso",
2174 			.ops		= &pxa25x_ep_ops,
2175 			.maxpacket	= ISO_FIFO_SIZE,
2176 			.caps		= USB_EP_CAPS(USB_EP_CAPS_TYPE_ISO,
2177 						USB_EP_CAPS_DIR_OUT),
2178 		},
2179 		.dev		= &memory,
2180 		.fifo_size	= ISO_FIFO_SIZE,
2181 		.bEndpointAddress = 9,
2182 		.bmAttributes	= USB_ENDPOINT_XFER_ISOC,
2183 		.regoff_udccs	= UDCCS9,
2184 		.regoff_ubcr	= UBCR9,
2185 		.regoff_uddr	= UDDR9,
2186 	},
2187 	.ep[10] = {
2188 		.ep = {
2189 			.name		= "ep10in-int",
2190 			.ops		= &pxa25x_ep_ops,
2191 			.maxpacket	= INT_FIFO_SIZE,
2192 			.caps		= USB_EP_CAPS(0, 0),
2193 		},
2194 		.dev		= &memory,
2195 		.fifo_size	= INT_FIFO_SIZE,
2196 		.bEndpointAddress = USB_DIR_IN | 10,
2197 		.bmAttributes	= USB_ENDPOINT_XFER_INT,
2198 		.regoff_udccs	= UDCCS10,
2199 		.regoff_uddr	= UDDR10,
2200 	},
2201 
2202 	/* third group of endpoints */
2203 	.ep[11] = {
2204 		.ep = {
2205 			.name		= "ep11in-bulk",
2206 			.ops		= &pxa25x_ep_ops,
2207 			.maxpacket	= BULK_FIFO_SIZE,
2208 			.caps		= USB_EP_CAPS(USB_EP_CAPS_TYPE_BULK,
2209 						USB_EP_CAPS_DIR_IN),
2210 		},
2211 		.dev		= &memory,
2212 		.fifo_size	= BULK_FIFO_SIZE,
2213 		.bEndpointAddress = USB_DIR_IN | 11,
2214 		.bmAttributes	= USB_ENDPOINT_XFER_BULK,
2215 		.regoff_udccs	= UDCCS11,
2216 		.regoff_uddr	= UDDR11,
2217 	},
2218 	.ep[12] = {
2219 		.ep = {
2220 			.name		= "ep12out-bulk",
2221 			.ops		= &pxa25x_ep_ops,
2222 			.maxpacket	= BULK_FIFO_SIZE,
2223 			.caps		= USB_EP_CAPS(USB_EP_CAPS_TYPE_BULK,
2224 						USB_EP_CAPS_DIR_OUT),
2225 		},
2226 		.dev		= &memory,
2227 		.fifo_size	= BULK_FIFO_SIZE,
2228 		.bEndpointAddress = 12,
2229 		.bmAttributes	= USB_ENDPOINT_XFER_BULK,
2230 		.regoff_udccs	= UDCCS12,
2231 		.regoff_ubcr	= UBCR12,
2232 		.regoff_uddr	= UDDR12,
2233 	},
2234 	.ep[13] = {
2235 		.ep = {
2236 			.name		= "ep13in-iso",
2237 			.ops		= &pxa25x_ep_ops,
2238 			.maxpacket	= ISO_FIFO_SIZE,
2239 			.caps		= USB_EP_CAPS(USB_EP_CAPS_TYPE_ISO,
2240 						USB_EP_CAPS_DIR_IN),
2241 		},
2242 		.dev		= &memory,
2243 		.fifo_size	= ISO_FIFO_SIZE,
2244 		.bEndpointAddress = USB_DIR_IN | 13,
2245 		.bmAttributes	= USB_ENDPOINT_XFER_ISOC,
2246 		.regoff_udccs	= UDCCS13,
2247 		.regoff_uddr	= UDDR13,
2248 	},
2249 	.ep[14] = {
2250 		.ep = {
2251 			.name		= "ep14out-iso",
2252 			.ops		= &pxa25x_ep_ops,
2253 			.maxpacket	= ISO_FIFO_SIZE,
2254 			.caps		= USB_EP_CAPS(USB_EP_CAPS_TYPE_ISO,
2255 						USB_EP_CAPS_DIR_OUT),
2256 		},
2257 		.dev		= &memory,
2258 		.fifo_size	= ISO_FIFO_SIZE,
2259 		.bEndpointAddress = 14,
2260 		.bmAttributes	= USB_ENDPOINT_XFER_ISOC,
2261 		.regoff_udccs	= UDCCS14,
2262 		.regoff_ubcr	= UBCR14,
2263 		.regoff_uddr	= UDDR14,
2264 	},
2265 	.ep[15] = {
2266 		.ep = {
2267 			.name		= "ep15in-int",
2268 			.ops		= &pxa25x_ep_ops,
2269 			.maxpacket	= INT_FIFO_SIZE,
2270 			.caps		= USB_EP_CAPS(0, 0),
2271 		},
2272 		.dev		= &memory,
2273 		.fifo_size	= INT_FIFO_SIZE,
2274 		.bEndpointAddress = USB_DIR_IN | 15,
2275 		.bmAttributes	= USB_ENDPOINT_XFER_INT,
2276 		.regoff_udccs	= UDCCS15,
2277 		.regoff_uddr	= UDDR15,
2278 	},
2279 #endif /* !CONFIG_USB_PXA25X_SMALL */
2280 };
2281 
2282 #define CP15R0_VENDOR_MASK	0xffffe000
2283 
2284 #if	defined(CONFIG_ARCH_PXA)
2285 #define CP15R0_XSCALE_VALUE	0x69052000	/* intel/arm/xscale */
2286 
2287 #elif	defined(CONFIG_ARCH_IXP4XX)
2288 #define CP15R0_XSCALE_VALUE	0x69054000	/* intel/arm/ixp4xx */
2289 
2290 #endif
2291 
2292 #define CP15R0_PROD_MASK	0x000003f0
2293 #define PXA25x			0x00000100	/* and PXA26x */
2294 #define PXA210			0x00000120
2295 
2296 #define CP15R0_REV_MASK		0x0000000f
2297 
2298 #define CP15R0_PRODREV_MASK	(CP15R0_PROD_MASK | CP15R0_REV_MASK)
2299 
2300 #define PXA255_A0		0x00000106	/* or PXA260_B1 */
2301 #define PXA250_C0		0x00000105	/* or PXA26x_B0 */
2302 #define PXA250_B2		0x00000104
2303 #define PXA250_B1		0x00000103	/* or PXA260_A0 */
2304 #define PXA250_B0		0x00000102
2305 #define PXA250_A1		0x00000101
2306 #define PXA250_A0		0x00000100
2307 
2308 #define PXA210_C0		0x00000125
2309 #define PXA210_B2		0x00000124
2310 #define PXA210_B1		0x00000123
2311 #define PXA210_B0		0x00000122
2312 #define IXP425_A0		0x000001c1
2313 #define IXP425_B0		0x000001f1
2314 #define IXP465_AD		0x00000200
2315 
2316 /*
2317  *	probe - binds to the platform device
2318  */
2319 static int pxa25x_udc_probe(struct platform_device *pdev)
2320 {
2321 	struct pxa25x_udc *dev = &memory;
2322 	int retval, irq;
2323 	u32 chiprev;
2324 	struct resource *res;
2325 
2326 	pr_info("%s: version %s\n", driver_name, DRIVER_VERSION);
2327 
2328 	/* insist on Intel/ARM/XScale */
2329 	asm("mrc%? p15, 0, %0, c0, c0" : "=r" (chiprev));
2330 	if ((chiprev & CP15R0_VENDOR_MASK) != CP15R0_XSCALE_VALUE) {
2331 		pr_err("%s: not XScale!\n", driver_name);
2332 		return -ENODEV;
2333 	}
2334 
2335 	/* trigger chiprev-specific logic */
2336 	switch (chiprev & CP15R0_PRODREV_MASK) {
2337 #if	defined(CONFIG_ARCH_PXA)
2338 	case PXA255_A0:
2339 		dev->has_cfr = 1;
2340 		break;
2341 	case PXA250_A0:
2342 	case PXA250_A1:
2343 		/* A0/A1 "not released"; ep 13, 15 unusable */
2344 		/* fall through */
2345 	case PXA250_B2: case PXA210_B2:
2346 	case PXA250_B1: case PXA210_B1:
2347 	case PXA250_B0: case PXA210_B0:
2348 		/* OUT-DMA is broken ... */
2349 		/* fall through */
2350 	case PXA250_C0: case PXA210_C0:
2351 		break;
2352 #elif	defined(CONFIG_ARCH_IXP4XX)
2353 	case IXP425_A0:
2354 	case IXP425_B0:
2355 	case IXP465_AD:
2356 		dev->has_cfr = 1;
2357 		break;
2358 #endif
2359 	default:
2360 		pr_err("%s: unrecognized processor: %08x\n",
2361 			driver_name, chiprev);
2362 		/* iop3xx, ixp4xx, ... */
2363 		return -ENODEV;
2364 	}
2365 
2366 	irq = platform_get_irq(pdev, 0);
2367 	if (irq < 0)
2368 		return -ENODEV;
2369 
2370 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
2371 	dev->regs = devm_ioremap_resource(&pdev->dev, res);
2372 	if (IS_ERR(dev->regs))
2373 		return PTR_ERR(dev->regs);
2374 
2375 	dev->clk = devm_clk_get(&pdev->dev, NULL);
2376 	if (IS_ERR(dev->clk))
2377 		return PTR_ERR(dev->clk);
2378 
2379 	pr_debug("%s: IRQ %d%s%s\n", driver_name, irq,
2380 		dev->has_cfr ? "" : " (!cfr)",
2381 		SIZE_STR "(pio)"
2382 		);
2383 
2384 	/* other non-static parts of init */
2385 	dev->dev = &pdev->dev;
2386 	dev->mach = dev_get_platdata(&pdev->dev);
2387 
2388 	dev->transceiver = devm_usb_get_phy(&pdev->dev, USB_PHY_TYPE_USB2);
2389 
2390 	if (gpio_is_valid(dev->mach->gpio_pullup)) {
2391 		retval = devm_gpio_request(&pdev->dev, dev->mach->gpio_pullup,
2392 					   "pca25x_udc GPIO PULLUP");
2393 		if (retval) {
2394 			dev_dbg(&pdev->dev,
2395 				"can't get pullup gpio %d, err: %d\n",
2396 				dev->mach->gpio_pullup, retval);
2397 			goto err;
2398 		}
2399 		gpio_direction_output(dev->mach->gpio_pullup, 0);
2400 	}
2401 
2402 	timer_setup(&dev->timer, udc_watchdog, 0);
2403 
2404 	the_controller = dev;
2405 	platform_set_drvdata(pdev, dev);
2406 
2407 	udc_disable(dev);
2408 	udc_reinit(dev);
2409 
2410 	dev->vbus = 0;
2411 
2412 	/* irq setup after old hardware state is cleaned up */
2413 	retval = devm_request_irq(&pdev->dev, irq, pxa25x_udc_irq, 0,
2414 				  driver_name, dev);
2415 	if (retval != 0) {
2416 		pr_err("%s: can't get irq %d, err %d\n",
2417 			driver_name, irq, retval);
2418 		goto err;
2419 	}
2420 	dev->got_irq = 1;
2421 
2422 #ifdef CONFIG_ARCH_LUBBOCK
2423 	if (machine_is_lubbock()) {
2424 		retval = devm_request_irq(&pdev->dev, LUBBOCK_USB_DISC_IRQ,
2425 					  lubbock_vbus_irq, 0, driver_name,
2426 					  dev);
2427 		if (retval != 0) {
2428 			pr_err("%s: can't get irq %i, err %d\n",
2429 				driver_name, LUBBOCK_USB_DISC_IRQ, retval);
2430 			goto err;
2431 		}
2432 		retval = devm_request_irq(&pdev->dev, LUBBOCK_USB_IRQ,
2433 					  lubbock_vbus_irq, 0, driver_name,
2434 					  dev);
2435 		if (retval != 0) {
2436 			pr_err("%s: can't get irq %i, err %d\n",
2437 				driver_name, LUBBOCK_USB_IRQ, retval);
2438 			goto err;
2439 		}
2440 	} else
2441 #endif
2442 	create_debug_files(dev);
2443 
2444 	retval = usb_add_gadget_udc(&pdev->dev, &dev->gadget);
2445 	if (!retval)
2446 		return retval;
2447 
2448 	remove_debug_files(dev);
2449  err:
2450 	if (!IS_ERR_OR_NULL(dev->transceiver))
2451 		dev->transceiver = NULL;
2452 	return retval;
2453 }
2454 
2455 static void pxa25x_udc_shutdown(struct platform_device *_dev)
2456 {
2457 	pullup_off();
2458 }
2459 
2460 static int pxa25x_udc_remove(struct platform_device *pdev)
2461 {
2462 	struct pxa25x_udc *dev = platform_get_drvdata(pdev);
2463 
2464 	if (dev->driver)
2465 		return -EBUSY;
2466 
2467 	usb_del_gadget_udc(&dev->gadget);
2468 	dev->pullup = 0;
2469 	pullup(dev);
2470 
2471 	remove_debug_files(dev);
2472 
2473 	if (!IS_ERR_OR_NULL(dev->transceiver))
2474 		dev->transceiver = NULL;
2475 
2476 	the_controller = NULL;
2477 	return 0;
2478 }
2479 
2480 /*-------------------------------------------------------------------------*/
2481 
2482 #ifdef	CONFIG_PM
2483 
2484 /* USB suspend (controlled by the host) and system suspend (controlled
2485  * by the PXA) don't necessarily work well together.  If USB is active,
2486  * the 48 MHz clock is required; so the system can't enter 33 MHz idle
2487  * mode, or any deeper PM saving state.
2488  *
2489  * For now, we punt and forcibly disconnect from the USB host when PXA
2490  * enters any suspend state.  While we're disconnected, we always disable
2491  * the 48MHz USB clock ... allowing PXA sleep and/or 33 MHz idle states.
2492  * Boards without software pullup control shouldn't use those states.
2493  * VBUS IRQs should probably be ignored so that the PXA device just acts
2494  * "dead" to USB hosts until system resume.
2495  */
2496 static int pxa25x_udc_suspend(struct platform_device *dev, pm_message_t state)
2497 {
2498 	struct pxa25x_udc	*udc = platform_get_drvdata(dev);
2499 	unsigned long flags;
2500 
2501 	if (!gpio_is_valid(udc->mach->gpio_pullup) && !udc->mach->udc_command)
2502 		WARNING("USB host won't detect disconnect!\n");
2503 	udc->suspended = 1;
2504 
2505 	local_irq_save(flags);
2506 	pullup(udc);
2507 	local_irq_restore(flags);
2508 
2509 	return 0;
2510 }
2511 
2512 static int pxa25x_udc_resume(struct platform_device *dev)
2513 {
2514 	struct pxa25x_udc	*udc = platform_get_drvdata(dev);
2515 	unsigned long flags;
2516 
2517 	udc->suspended = 0;
2518 	local_irq_save(flags);
2519 	pullup(udc);
2520 	local_irq_restore(flags);
2521 
2522 	return 0;
2523 }
2524 
2525 #else
2526 #define	pxa25x_udc_suspend	NULL
2527 #define	pxa25x_udc_resume	NULL
2528 #endif
2529 
2530 /*-------------------------------------------------------------------------*/
2531 
2532 static struct platform_driver udc_driver = {
2533 	.shutdown	= pxa25x_udc_shutdown,
2534 	.probe		= pxa25x_udc_probe,
2535 	.remove		= pxa25x_udc_remove,
2536 	.suspend	= pxa25x_udc_suspend,
2537 	.resume		= pxa25x_udc_resume,
2538 	.driver		= {
2539 		.name	= "pxa25x-udc",
2540 	},
2541 };
2542 
2543 module_platform_driver(udc_driver);
2544 
2545 MODULE_DESCRIPTION(DRIVER_DESC);
2546 MODULE_AUTHOR("Frank Becker, Robert Schwebel, David Brownell");
2547 MODULE_LICENSE("GPL");
2548 MODULE_ALIAS("platform:pxa25x-udc");
2549