1 // SPDX-License-Identifier: GPL-2.0+ 2 /* 3 * Copyright (C) 2004,2012 Freescale Semiconductor, Inc 4 * All rights reserved. 5 * 6 * Freescale USB device/endpoint management registers 7 */ 8 #ifndef __FSL_USB2_UDC_H 9 #define __FSL_USB2_UDC_H 10 11 #include <linux/usb/ch9.h> 12 #include <linux/usb/gadget.h> 13 14 /* ### define USB registers here 15 */ 16 #define USB_MAX_CTRL_PAYLOAD 64 17 #define USB_DR_SYS_OFFSET 0x400 18 19 /* USB DR device mode registers (Little Endian) */ 20 struct usb_dr_device { 21 /* Capability register */ 22 u8 res1[256]; 23 u16 caplength; /* Capability Register Length */ 24 u16 hciversion; /* Host Controller Interface Version */ 25 u32 hcsparams; /* Host Controller Structural Parameters */ 26 u32 hccparams; /* Host Controller Capability Parameters */ 27 u8 res2[20]; 28 u32 dciversion; /* Device Controller Interface Version */ 29 u32 dccparams; /* Device Controller Capability Parameters */ 30 u8 res3[24]; 31 /* Operation register */ 32 u32 usbcmd; /* USB Command Register */ 33 u32 usbsts; /* USB Status Register */ 34 u32 usbintr; /* USB Interrupt Enable Register */ 35 u32 frindex; /* Frame Index Register */ 36 u8 res4[4]; 37 u32 deviceaddr; /* Device Address */ 38 u32 endpointlistaddr; /* Endpoint List Address Register */ 39 u8 res5[4]; 40 u32 burstsize; /* Master Interface Data Burst Size Register */ 41 u32 txttfilltuning; /* Transmit FIFO Tuning Controls Register */ 42 u8 res6[24]; 43 u32 configflag; /* Configure Flag Register */ 44 u32 portsc1; /* Port 1 Status and Control Register */ 45 u8 res7[28]; 46 u32 otgsc; /* On-The-Go Status and Control */ 47 u32 usbmode; /* USB Mode Register */ 48 u32 endptsetupstat; /* Endpoint Setup Status Register */ 49 u32 endpointprime; /* Endpoint Initialization Register */ 50 u32 endptflush; /* Endpoint Flush Register */ 51 u32 endptstatus; /* Endpoint Status Register */ 52 u32 endptcomplete; /* Endpoint Complete Register */ 53 u32 endptctrl[6]; /* Endpoint Control Registers */ 54 }; 55 56 /* USB DR host mode registers (Little Endian) */ 57 struct usb_dr_host { 58 /* Capability register */ 59 u8 res1[256]; 60 u16 caplength; /* Capability Register Length */ 61 u16 hciversion; /* Host Controller Interface Version */ 62 u32 hcsparams; /* Host Controller Structural Parameters */ 63 u32 hccparams; /* Host Controller Capability Parameters */ 64 u8 res2[20]; 65 u32 dciversion; /* Device Controller Interface Version */ 66 u32 dccparams; /* Device Controller Capability Parameters */ 67 u8 res3[24]; 68 /* Operation register */ 69 u32 usbcmd; /* USB Command Register */ 70 u32 usbsts; /* USB Status Register */ 71 u32 usbintr; /* USB Interrupt Enable Register */ 72 u32 frindex; /* Frame Index Register */ 73 u8 res4[4]; 74 u32 periodiclistbase; /* Periodic Frame List Base Address Register */ 75 u32 asynclistaddr; /* Current Asynchronous List Address Register */ 76 u8 res5[4]; 77 u32 burstsize; /* Master Interface Data Burst Size Register */ 78 u32 txttfilltuning; /* Transmit FIFO Tuning Controls Register */ 79 u8 res6[24]; 80 u32 configflag; /* Configure Flag Register */ 81 u32 portsc1; /* Port 1 Status and Control Register */ 82 u8 res7[28]; 83 u32 otgsc; /* On-The-Go Status and Control */ 84 u32 usbmode; /* USB Mode Register */ 85 u32 endptsetupstat; /* Endpoint Setup Status Register */ 86 u32 endpointprime; /* Endpoint Initialization Register */ 87 u32 endptflush; /* Endpoint Flush Register */ 88 u32 endptstatus; /* Endpoint Status Register */ 89 u32 endptcomplete; /* Endpoint Complete Register */ 90 u32 endptctrl[6]; /* Endpoint Control Registers */ 91 }; 92 93 /* non-EHCI USB system interface registers (Big Endian) */ 94 struct usb_sys_interface { 95 u32 snoop1; 96 u32 snoop2; 97 u32 age_cnt_thresh; /* Age Count Threshold Register */ 98 u32 pri_ctrl; /* Priority Control Register */ 99 u32 si_ctrl; /* System Interface Control Register */ 100 u8 res[236]; 101 u32 control; /* General Purpose Control Register */ 102 }; 103 104 /* ep0 transfer state */ 105 #define WAIT_FOR_SETUP 0 106 #define DATA_STATE_XMIT 1 107 #define DATA_STATE_NEED_ZLP 2 108 #define WAIT_FOR_OUT_STATUS 3 109 #define DATA_STATE_RECV 4 110 111 /* Device Controller Capability Parameter register */ 112 #define DCCPARAMS_DC 0x00000080 113 #define DCCPARAMS_DEN_MASK 0x0000001f 114 115 /* Frame Index Register Bit Masks */ 116 #define USB_FRINDEX_MASKS 0x3fff 117 /* USB CMD Register Bit Masks */ 118 #define USB_CMD_RUN_STOP 0x00000001 119 #define USB_CMD_CTRL_RESET 0x00000002 120 #define USB_CMD_PERIODIC_SCHEDULE_EN 0x00000010 121 #define USB_CMD_ASYNC_SCHEDULE_EN 0x00000020 122 #define USB_CMD_INT_AA_DOORBELL 0x00000040 123 #define USB_CMD_ASP 0x00000300 124 #define USB_CMD_ASYNC_SCH_PARK_EN 0x00000800 125 #define USB_CMD_SUTW 0x00002000 126 #define USB_CMD_ATDTW 0x00004000 127 #define USB_CMD_ITC 0x00FF0000 128 129 /* bit 15,3,2 are frame list size */ 130 #define USB_CMD_FRAME_SIZE_1024 0x00000000 131 #define USB_CMD_FRAME_SIZE_512 0x00000004 132 #define USB_CMD_FRAME_SIZE_256 0x00000008 133 #define USB_CMD_FRAME_SIZE_128 0x0000000C 134 #define USB_CMD_FRAME_SIZE_64 0x00008000 135 #define USB_CMD_FRAME_SIZE_32 0x00008004 136 #define USB_CMD_FRAME_SIZE_16 0x00008008 137 #define USB_CMD_FRAME_SIZE_8 0x0000800C 138 139 /* bit 9-8 are async schedule park mode count */ 140 #define USB_CMD_ASP_00 0x00000000 141 #define USB_CMD_ASP_01 0x00000100 142 #define USB_CMD_ASP_10 0x00000200 143 #define USB_CMD_ASP_11 0x00000300 144 #define USB_CMD_ASP_BIT_POS 8 145 146 /* bit 23-16 are interrupt threshold control */ 147 #define USB_CMD_ITC_NO_THRESHOLD 0x00000000 148 #define USB_CMD_ITC_1_MICRO_FRM 0x00010000 149 #define USB_CMD_ITC_2_MICRO_FRM 0x00020000 150 #define USB_CMD_ITC_4_MICRO_FRM 0x00040000 151 #define USB_CMD_ITC_8_MICRO_FRM 0x00080000 152 #define USB_CMD_ITC_16_MICRO_FRM 0x00100000 153 #define USB_CMD_ITC_32_MICRO_FRM 0x00200000 154 #define USB_CMD_ITC_64_MICRO_FRM 0x00400000 155 #define USB_CMD_ITC_BIT_POS 16 156 157 /* USB STS Register Bit Masks */ 158 #define USB_STS_INT 0x00000001 159 #define USB_STS_ERR 0x00000002 160 #define USB_STS_PORT_CHANGE 0x00000004 161 #define USB_STS_FRM_LST_ROLL 0x00000008 162 #define USB_STS_SYS_ERR 0x00000010 163 #define USB_STS_IAA 0x00000020 164 #define USB_STS_RESET 0x00000040 165 #define USB_STS_SOF 0x00000080 166 #define USB_STS_SUSPEND 0x00000100 167 #define USB_STS_HC_HALTED 0x00001000 168 #define USB_STS_RCL 0x00002000 169 #define USB_STS_PERIODIC_SCHEDULE 0x00004000 170 #define USB_STS_ASYNC_SCHEDULE 0x00008000 171 172 /* USB INTR Register Bit Masks */ 173 #define USB_INTR_INT_EN 0x00000001 174 #define USB_INTR_ERR_INT_EN 0x00000002 175 #define USB_INTR_PTC_DETECT_EN 0x00000004 176 #define USB_INTR_FRM_LST_ROLL_EN 0x00000008 177 #define USB_INTR_SYS_ERR_EN 0x00000010 178 #define USB_INTR_ASYN_ADV_EN 0x00000020 179 #define USB_INTR_RESET_EN 0x00000040 180 #define USB_INTR_SOF_EN 0x00000080 181 #define USB_INTR_DEVICE_SUSPEND 0x00000100 182 183 /* Device Address bit masks */ 184 #define USB_DEVICE_ADDRESS_MASK 0xFE000000 185 #define USB_DEVICE_ADDRESS_BIT_POS 25 186 187 /* endpoint list address bit masks */ 188 #define USB_EP_LIST_ADDRESS_MASK 0xfffff800 189 190 /* PORTSCX Register Bit Masks */ 191 #define PORTSCX_CURRENT_CONNECT_STATUS 0x00000001 192 #define PORTSCX_CONNECT_STATUS_CHANGE 0x00000002 193 #define PORTSCX_PORT_ENABLE 0x00000004 194 #define PORTSCX_PORT_EN_DIS_CHANGE 0x00000008 195 #define PORTSCX_OVER_CURRENT_ACT 0x00000010 196 #define PORTSCX_OVER_CURRENT_CHG 0x00000020 197 #define PORTSCX_PORT_FORCE_RESUME 0x00000040 198 #define PORTSCX_PORT_SUSPEND 0x00000080 199 #define PORTSCX_PORT_RESET 0x00000100 200 #define PORTSCX_LINE_STATUS_BITS 0x00000C00 201 #define PORTSCX_PORT_POWER 0x00001000 202 #define PORTSCX_PORT_INDICTOR_CTRL 0x0000C000 203 #define PORTSCX_PORT_TEST_CTRL 0x000F0000 204 #define PORTSCX_WAKE_ON_CONNECT_EN 0x00100000 205 #define PORTSCX_WAKE_ON_CONNECT_DIS 0x00200000 206 #define PORTSCX_WAKE_ON_OVER_CURRENT 0x00400000 207 #define PORTSCX_PHY_LOW_POWER_SPD 0x00800000 208 #define PORTSCX_PORT_FORCE_FULL_SPEED 0x01000000 209 #define PORTSCX_PORT_SPEED_MASK 0x0C000000 210 #define PORTSCX_PORT_WIDTH 0x10000000 211 #define PORTSCX_PHY_TYPE_SEL 0xC0000000 212 213 /* bit 11-10 are line status */ 214 #define PORTSCX_LINE_STATUS_SE0 0x00000000 215 #define PORTSCX_LINE_STATUS_JSTATE 0x00000400 216 #define PORTSCX_LINE_STATUS_KSTATE 0x00000800 217 #define PORTSCX_LINE_STATUS_UNDEF 0x00000C00 218 #define PORTSCX_LINE_STATUS_BIT_POS 10 219 220 /* bit 15-14 are port indicator control */ 221 #define PORTSCX_PIC_OFF 0x00000000 222 #define PORTSCX_PIC_AMBER 0x00004000 223 #define PORTSCX_PIC_GREEN 0x00008000 224 #define PORTSCX_PIC_UNDEF 0x0000C000 225 #define PORTSCX_PIC_BIT_POS 14 226 227 /* bit 19-16 are port test control */ 228 #define PORTSCX_PTC_DISABLE 0x00000000 229 #define PORTSCX_PTC_JSTATE 0x00010000 230 #define PORTSCX_PTC_KSTATE 0x00020000 231 #define PORTSCX_PTC_SEQNAK 0x00030000 232 #define PORTSCX_PTC_PACKET 0x00040000 233 #define PORTSCX_PTC_FORCE_EN 0x00050000 234 #define PORTSCX_PTC_BIT_POS 16 235 236 /* bit 27-26 are port speed */ 237 #define PORTSCX_PORT_SPEED_FULL 0x00000000 238 #define PORTSCX_PORT_SPEED_LOW 0x04000000 239 #define PORTSCX_PORT_SPEED_HIGH 0x08000000 240 #define PORTSCX_PORT_SPEED_UNDEF 0x0C000000 241 #define PORTSCX_SPEED_BIT_POS 26 242 243 /* bit 28 is parallel transceiver width for UTMI interface */ 244 #define PORTSCX_PTW 0x10000000 245 #define PORTSCX_PTW_8BIT 0x00000000 246 #define PORTSCX_PTW_16BIT 0x10000000 247 248 /* bit 31-30 are port transceiver select */ 249 #define PORTSCX_PTS_UTMI 0x00000000 250 #define PORTSCX_PTS_ULPI 0x80000000 251 #define PORTSCX_PTS_FSLS 0xC0000000 252 #define PORTSCX_PTS_BIT_POS 30 253 254 /* otgsc Register Bit Masks */ 255 #define OTGSC_CTRL_VUSB_DISCHARGE 0x00000001 256 #define OTGSC_CTRL_VUSB_CHARGE 0x00000002 257 #define OTGSC_CTRL_OTG_TERM 0x00000008 258 #define OTGSC_CTRL_DATA_PULSING 0x00000010 259 #define OTGSC_STS_USB_ID 0x00000100 260 #define OTGSC_STS_A_VBUS_VALID 0x00000200 261 #define OTGSC_STS_A_SESSION_VALID 0x00000400 262 #define OTGSC_STS_B_SESSION_VALID 0x00000800 263 #define OTGSC_STS_B_SESSION_END 0x00001000 264 #define OTGSC_STS_1MS_TOGGLE 0x00002000 265 #define OTGSC_STS_DATA_PULSING 0x00004000 266 #define OTGSC_INTSTS_USB_ID 0x00010000 267 #define OTGSC_INTSTS_A_VBUS_VALID 0x00020000 268 #define OTGSC_INTSTS_A_SESSION_VALID 0x00040000 269 #define OTGSC_INTSTS_B_SESSION_VALID 0x00080000 270 #define OTGSC_INTSTS_B_SESSION_END 0x00100000 271 #define OTGSC_INTSTS_1MS 0x00200000 272 #define OTGSC_INTSTS_DATA_PULSING 0x00400000 273 #define OTGSC_INTR_USB_ID 0x01000000 274 #define OTGSC_INTR_A_VBUS_VALID 0x02000000 275 #define OTGSC_INTR_A_SESSION_VALID 0x04000000 276 #define OTGSC_INTR_B_SESSION_VALID 0x08000000 277 #define OTGSC_INTR_B_SESSION_END 0x10000000 278 #define OTGSC_INTR_1MS_TIMER 0x20000000 279 #define OTGSC_INTR_DATA_PULSING 0x40000000 280 281 /* USB MODE Register Bit Masks */ 282 #define USB_MODE_CTRL_MODE_IDLE 0x00000000 283 #define USB_MODE_CTRL_MODE_DEVICE 0x00000002 284 #define USB_MODE_CTRL_MODE_HOST 0x00000003 285 #define USB_MODE_CTRL_MODE_MASK 0x00000003 286 #define USB_MODE_CTRL_MODE_RSV 0x00000001 287 #define USB_MODE_ES 0x00000004 /* Endian Select */ 288 #define USB_MODE_SETUP_LOCK_OFF 0x00000008 289 #define USB_MODE_STREAM_DISABLE 0x00000010 290 /* Endpoint Flush Register */ 291 #define EPFLUSH_TX_OFFSET 0x00010000 292 #define EPFLUSH_RX_OFFSET 0x00000000 293 294 /* Endpoint Setup Status bit masks */ 295 #define EP_SETUP_STATUS_MASK 0x0000003F 296 #define EP_SETUP_STATUS_EP0 0x00000001 297 298 /* ENDPOINTCTRLx Register Bit Masks */ 299 #define EPCTRL_TX_ENABLE 0x00800000 300 #define EPCTRL_TX_DATA_TOGGLE_RST 0x00400000 /* Not EP0 */ 301 #define EPCTRL_TX_DATA_TOGGLE_INH 0x00200000 /* Not EP0 */ 302 #define EPCTRL_TX_TYPE 0x000C0000 303 #define EPCTRL_TX_DATA_SOURCE 0x00020000 /* Not EP0 */ 304 #define EPCTRL_TX_EP_STALL 0x00010000 305 #define EPCTRL_RX_ENABLE 0x00000080 306 #define EPCTRL_RX_DATA_TOGGLE_RST 0x00000040 /* Not EP0 */ 307 #define EPCTRL_RX_DATA_TOGGLE_INH 0x00000020 /* Not EP0 */ 308 #define EPCTRL_RX_TYPE 0x0000000C 309 #define EPCTRL_RX_DATA_SINK 0x00000002 /* Not EP0 */ 310 #define EPCTRL_RX_EP_STALL 0x00000001 311 312 /* bit 19-18 and 3-2 are endpoint type */ 313 #define EPCTRL_EP_TYPE_CONTROL 0 314 #define EPCTRL_EP_TYPE_ISO 1 315 #define EPCTRL_EP_TYPE_BULK 2 316 #define EPCTRL_EP_TYPE_INTERRUPT 3 317 #define EPCTRL_TX_EP_TYPE_SHIFT 18 318 #define EPCTRL_RX_EP_TYPE_SHIFT 2 319 320 /* SNOOPn Register Bit Masks */ 321 #define SNOOP_ADDRESS_MASK 0xFFFFF000 322 #define SNOOP_SIZE_ZERO 0x00 /* snooping disable */ 323 #define SNOOP_SIZE_4KB 0x0B /* 4KB snoop size */ 324 #define SNOOP_SIZE_8KB 0x0C 325 #define SNOOP_SIZE_16KB 0x0D 326 #define SNOOP_SIZE_32KB 0x0E 327 #define SNOOP_SIZE_64KB 0x0F 328 #define SNOOP_SIZE_128KB 0x10 329 #define SNOOP_SIZE_256KB 0x11 330 #define SNOOP_SIZE_512KB 0x12 331 #define SNOOP_SIZE_1MB 0x13 332 #define SNOOP_SIZE_2MB 0x14 333 #define SNOOP_SIZE_4MB 0x15 334 #define SNOOP_SIZE_8MB 0x16 335 #define SNOOP_SIZE_16MB 0x17 336 #define SNOOP_SIZE_32MB 0x18 337 #define SNOOP_SIZE_64MB 0x19 338 #define SNOOP_SIZE_128MB 0x1A 339 #define SNOOP_SIZE_256MB 0x1B 340 #define SNOOP_SIZE_512MB 0x1C 341 #define SNOOP_SIZE_1GB 0x1D 342 #define SNOOP_SIZE_2GB 0x1E /* 2GB snoop size */ 343 344 /* pri_ctrl Register Bit Masks */ 345 #define PRI_CTRL_PRI_LVL1 0x0000000C 346 #define PRI_CTRL_PRI_LVL0 0x00000003 347 348 /* si_ctrl Register Bit Masks */ 349 #define SI_CTRL_ERR_DISABLE 0x00000010 350 #define SI_CTRL_IDRC_DISABLE 0x00000008 351 #define SI_CTRL_RD_SAFE_EN 0x00000004 352 #define SI_CTRL_RD_PREFETCH_DISABLE 0x00000002 353 #define SI_CTRL_RD_PREFEFETCH_VAL 0x00000001 354 355 /* control Register Bit Masks */ 356 #define USB_CTRL_IOENB 0x00000004 357 #define USB_CTRL_ULPI_INT0EN 0x00000001 358 #define USB_CTRL_UTMI_PHY_EN 0x00000200 359 #define USB_CTRL_USB_EN 0x00000004 360 #define USB_CTRL_ULPI_PHY_CLK_SEL 0x00000400 361 362 /* Endpoint Queue Head data struct 363 * Rem: all the variables of qh are LittleEndian Mode 364 * and NEXT_POINTER_MASK should operate on a LittleEndian, Phy Addr 365 */ 366 struct ep_queue_head { 367 u32 max_pkt_length; /* Mult(31-30) , Zlt(29) , Max Pkt len 368 and IOS(15) */ 369 u32 curr_dtd_ptr; /* Current dTD Pointer(31-5) */ 370 u32 next_dtd_ptr; /* Next dTD Pointer(31-5), T(0) */ 371 u32 size_ioc_int_sts; /* Total bytes (30-16), IOC (15), 372 MultO(11-10), STS (7-0) */ 373 u32 buff_ptr0; /* Buffer pointer Page 0 (31-12) */ 374 u32 buff_ptr1; /* Buffer pointer Page 1 (31-12) */ 375 u32 buff_ptr2; /* Buffer pointer Page 2 (31-12) */ 376 u32 buff_ptr3; /* Buffer pointer Page 3 (31-12) */ 377 u32 buff_ptr4; /* Buffer pointer Page 4 (31-12) */ 378 u32 res1; 379 u8 setup_buffer[8]; /* Setup data 8 bytes */ 380 u32 res2[4]; 381 }; 382 383 /* Endpoint Queue Head Bit Masks */ 384 #define EP_QUEUE_HEAD_MULT_POS 30 385 #define EP_QUEUE_HEAD_ZLT_SEL 0x20000000 386 #define EP_QUEUE_HEAD_MAX_PKT_LEN_POS 16 387 #define EP_QUEUE_HEAD_MAX_PKT_LEN(ep_info) (((ep_info)>>16)&0x07ff) 388 #define EP_QUEUE_HEAD_IOS 0x00008000 389 #define EP_QUEUE_HEAD_NEXT_TERMINATE 0x00000001 390 #define EP_QUEUE_HEAD_IOC 0x00008000 391 #define EP_QUEUE_HEAD_MULTO 0x00000C00 392 #define EP_QUEUE_HEAD_STATUS_HALT 0x00000040 393 #define EP_QUEUE_HEAD_STATUS_ACTIVE 0x00000080 394 #define EP_QUEUE_CURRENT_OFFSET_MASK 0x00000FFF 395 #define EP_QUEUE_HEAD_NEXT_POINTER_MASK 0xFFFFFFE0 396 #define EP_QUEUE_FRINDEX_MASK 0x000007FF 397 #define EP_MAX_LENGTH_TRANSFER 0x4000 398 399 /* Endpoint Transfer Descriptor data struct */ 400 /* Rem: all the variables of td are LittleEndian Mode */ 401 struct ep_td_struct { 402 u32 next_td_ptr; /* Next TD pointer(31-5), T(0) set 403 indicate invalid */ 404 u32 size_ioc_sts; /* Total bytes (30-16), IOC (15), 405 MultO(11-10), STS (7-0) */ 406 u32 buff_ptr0; /* Buffer pointer Page 0 */ 407 u32 buff_ptr1; /* Buffer pointer Page 1 */ 408 u32 buff_ptr2; /* Buffer pointer Page 2 */ 409 u32 buff_ptr3; /* Buffer pointer Page 3 */ 410 u32 buff_ptr4; /* Buffer pointer Page 4 */ 411 u32 res; 412 /* 32 bytes */ 413 dma_addr_t td_dma; /* dma address for this td */ 414 /* virtual address of next td specified in next_td_ptr */ 415 struct ep_td_struct *next_td_virt; 416 }; 417 418 /* Endpoint Transfer Descriptor bit Masks */ 419 #define DTD_NEXT_TERMINATE 0x00000001 420 #define DTD_IOC 0x00008000 421 #define DTD_STATUS_ACTIVE 0x00000080 422 #define DTD_STATUS_HALTED 0x00000040 423 #define DTD_STATUS_DATA_BUFF_ERR 0x00000020 424 #define DTD_STATUS_TRANSACTION_ERR 0x00000008 425 #define DTD_RESERVED_FIELDS 0x80007300 426 #define DTD_ADDR_MASK 0xFFFFFFE0 427 #define DTD_PACKET_SIZE 0x7FFF0000 428 #define DTD_LENGTH_BIT_POS 16 429 #define DTD_ERROR_MASK (DTD_STATUS_HALTED | \ 430 DTD_STATUS_DATA_BUFF_ERR | \ 431 DTD_STATUS_TRANSACTION_ERR) 432 /* Alignment requirements; must be a power of two */ 433 #define DTD_ALIGNMENT 0x20 434 #define QH_ALIGNMENT 2048 435 436 /* Controller dma boundary */ 437 #define UDC_DMA_BOUNDARY 0x1000 438 439 /*-------------------------------------------------------------------------*/ 440 441 /* ### driver private data 442 */ 443 struct fsl_req { 444 struct usb_request req; 445 struct list_head queue; 446 /* ep_queue() func will add 447 a request->queue into a udc_ep->queue 'd tail */ 448 struct fsl_ep *ep; 449 unsigned mapped:1; 450 451 struct ep_td_struct *head, *tail; /* For dTD List 452 cpu endian Virtual addr */ 453 unsigned int dtd_count; 454 }; 455 456 #define REQ_UNCOMPLETE 1 457 458 struct fsl_ep { 459 struct usb_ep ep; 460 struct list_head queue; 461 struct fsl_udc *udc; 462 struct ep_queue_head *qh; 463 struct usb_gadget *gadget; 464 465 char name[14]; 466 unsigned stopped:1; 467 }; 468 469 #define EP_DIR_IN 1 470 #define EP_DIR_OUT 0 471 472 struct fsl_udc { 473 struct usb_gadget gadget; 474 struct usb_gadget_driver *driver; 475 struct fsl_usb2_platform_data *pdata; 476 struct completion *done; /* to make sure release() is done */ 477 struct fsl_ep *eps; 478 unsigned int max_ep; 479 unsigned int irq; 480 481 struct usb_ctrlrequest local_setup_buff; 482 spinlock_t lock; 483 struct usb_phy *transceiver; 484 unsigned softconnect:1; 485 unsigned vbus_active:1; 486 unsigned stopped:1; 487 unsigned remote_wakeup:1; 488 unsigned already_stopped:1; 489 unsigned big_endian_desc:1; 490 491 struct ep_queue_head *ep_qh; /* Endpoints Queue-Head */ 492 struct fsl_req *status_req; /* ep0 status request */ 493 struct dma_pool *td_pool; /* dma pool for DTD */ 494 enum fsl_usb2_phy_modes phy_mode; 495 496 size_t ep_qh_size; /* size after alignment adjustment*/ 497 dma_addr_t ep_qh_dma; /* dma address of QH */ 498 499 u32 max_pipes; /* Device max pipes */ 500 u32 bus_reset; /* Device is bus resetting */ 501 u32 resume_state; /* USB state to resume */ 502 u32 usb_state; /* USB current state */ 503 u32 ep0_state; /* Endpoint zero state */ 504 u32 ep0_dir; /* Endpoint zero direction: can be 505 USB_DIR_IN or USB_DIR_OUT */ 506 u8 device_address; /* Device USB address */ 507 }; 508 509 /*-------------------------------------------------------------------------*/ 510 511 #ifdef DEBUG 512 #define DBG(fmt, args...) printk(KERN_DEBUG "[%s] " fmt "\n", \ 513 __func__, ## args) 514 #else 515 #define DBG(fmt, args...) do{}while(0) 516 #endif 517 518 #if 0 519 static void dump_msg(const char *label, const u8 * buf, unsigned int length) 520 { 521 unsigned int start, num, i; 522 char line[52], *p; 523 524 if (length >= 512) 525 return; 526 DBG("%s, length %u:\n", label, length); 527 start = 0; 528 while (length > 0) { 529 num = min(length, 16u); 530 p = line; 531 for (i = 0; i < num; ++i) { 532 if (i == 8) 533 *p++ = ' '; 534 sprintf(p, " %02x", buf[i]); 535 p += 3; 536 } 537 *p = 0; 538 printk(KERN_DEBUG "%6x: %s\n", start, line); 539 buf += num; 540 start += num; 541 length -= num; 542 } 543 } 544 #endif 545 546 #ifdef VERBOSE 547 #define VDBG DBG 548 #else 549 #define VDBG(stuff...) do{}while(0) 550 #endif 551 552 #define ERR(stuff...) pr_err("udc: " stuff) 553 #define WARNING(stuff...) pr_warn("udc: " stuff) 554 #define INFO(stuff...) pr_info("udc: " stuff) 555 556 /*-------------------------------------------------------------------------*/ 557 558 /* ### Add board specific defines here 559 */ 560 561 /* 562 * ### pipe direction macro from device view 563 */ 564 #define USB_RECV 0 /* OUT EP */ 565 #define USB_SEND 1 /* IN EP */ 566 567 /* 568 * ### internal used help routines. 569 */ 570 #define ep_index(EP) ((EP)->ep.desc->bEndpointAddress&0xF) 571 #define ep_maxpacket(EP) ((EP)->ep.maxpacket) 572 #define ep_is_in(EP) ( (ep_index(EP) == 0) ? (EP->udc->ep0_dir == \ 573 USB_DIR_IN) : ((EP)->ep.desc->bEndpointAddress \ 574 & USB_DIR_IN)==USB_DIR_IN) 575 #define get_ep_by_pipe(udc, pipe) ((pipe == 1)? &udc->eps[0]: \ 576 &udc->eps[pipe]) 577 #define get_pipe_by_windex(windex) ((windex & USB_ENDPOINT_NUMBER_MASK) \ 578 * 2 + ((windex & USB_DIR_IN) ? 1 : 0)) 579 #define get_pipe_by_ep(EP) (ep_index(EP) * 2 + ep_is_in(EP)) 580 581 static inline struct ep_queue_head *get_qh_by_ep(struct fsl_ep *ep) 582 { 583 /* we only have one ep0 structure but two queue heads */ 584 if (ep_index(ep) != 0) 585 return ep->qh; 586 else 587 return &ep->udc->ep_qh[(ep->udc->ep0_dir == 588 USB_DIR_IN) ? 1 : 0]; 589 } 590 591 struct platform_device; 592 #ifdef CONFIG_ARCH_MXC 593 int fsl_udc_clk_init(struct platform_device *pdev); 594 int fsl_udc_clk_finalize(struct platform_device *pdev); 595 void fsl_udc_clk_release(void); 596 #else 597 static inline int fsl_udc_clk_init(struct platform_device *pdev) 598 { 599 return 0; 600 } 601 static inline int fsl_udc_clk_finalize(struct platform_device *pdev) 602 { 603 return 0; 604 } 605 static inline void fsl_udc_clk_release(void) 606 { 607 } 608 #endif 609 610 #endif 611