1 // SPDX-License-Identifier: GPL-2.0+ 2 /* 3 * Copyright (C) 2004-2007,2011-2012 Freescale Semiconductor, Inc. 4 * All rights reserved. 5 * 6 * Author: Li Yang <leoli@freescale.com> 7 * Jiang Bo <tanya.jiang@freescale.com> 8 * 9 * Description: 10 * Freescale high-speed USB SOC DR module device controller driver. 11 * This can be found on MPC8349E/MPC8313E/MPC5121E cpus. 12 * The driver is previously named as mpc_udc. Based on bare board 13 * code from Dave Liu and Shlomi Gridish. 14 */ 15 16 #undef VERBOSE 17 18 #include <linux/module.h> 19 #include <linux/kernel.h> 20 #include <linux/ioport.h> 21 #include <linux/types.h> 22 #include <linux/errno.h> 23 #include <linux/err.h> 24 #include <linux/slab.h> 25 #include <linux/init.h> 26 #include <linux/list.h> 27 #include <linux/interrupt.h> 28 #include <linux/proc_fs.h> 29 #include <linux/mm.h> 30 #include <linux/moduleparam.h> 31 #include <linux/device.h> 32 #include <linux/usb/ch9.h> 33 #include <linux/usb/gadget.h> 34 #include <linux/usb/otg.h> 35 #include <linux/dma-mapping.h> 36 #include <linux/platform_device.h> 37 #include <linux/fsl_devices.h> 38 #include <linux/dmapool.h> 39 #include <linux/delay.h> 40 #include <linux/of_device.h> 41 42 #include <asm/byteorder.h> 43 #include <asm/io.h> 44 #include <asm/unaligned.h> 45 #include <asm/dma.h> 46 47 #include "fsl_usb2_udc.h" 48 49 #define DRIVER_DESC "Freescale High-Speed USB SOC Device Controller driver" 50 #define DRIVER_AUTHOR "Li Yang/Jiang Bo" 51 #define DRIVER_VERSION "Apr 20, 2007" 52 53 #define DMA_ADDR_INVALID (~(dma_addr_t)0) 54 55 static const char driver_name[] = "fsl-usb2-udc"; 56 static const char driver_desc[] = DRIVER_DESC; 57 58 static struct usb_dr_device __iomem *dr_regs; 59 60 static struct usb_sys_interface __iomem *usb_sys_regs; 61 62 /* it is initialized in probe() */ 63 static struct fsl_udc *udc_controller = NULL; 64 65 static const struct usb_endpoint_descriptor 66 fsl_ep0_desc = { 67 .bLength = USB_DT_ENDPOINT_SIZE, 68 .bDescriptorType = USB_DT_ENDPOINT, 69 .bEndpointAddress = 0, 70 .bmAttributes = USB_ENDPOINT_XFER_CONTROL, 71 .wMaxPacketSize = USB_MAX_CTRL_PAYLOAD, 72 }; 73 74 static void fsl_ep_fifo_flush(struct usb_ep *_ep); 75 76 #ifdef CONFIG_PPC32 77 /* 78 * On some SoCs, the USB controller registers can be big or little endian, 79 * depending on the version of the chip. In order to be able to run the 80 * same kernel binary on 2 different versions of an SoC, the BE/LE decision 81 * must be made at run time. _fsl_readl and fsl_writel are pointers to the 82 * BE or LE readl() and writel() functions, and fsl_readl() and fsl_writel() 83 * call through those pointers. Platform code for SoCs that have BE USB 84 * registers should set pdata->big_endian_mmio flag. 85 * 86 * This also applies to controller-to-cpu accessors for the USB descriptors, 87 * since their endianness is also SoC dependant. Platform code for SoCs that 88 * have BE USB descriptors should set pdata->big_endian_desc flag. 89 */ 90 static u32 _fsl_readl_be(const unsigned __iomem *p) 91 { 92 return in_be32(p); 93 } 94 95 static u32 _fsl_readl_le(const unsigned __iomem *p) 96 { 97 return in_le32(p); 98 } 99 100 static void _fsl_writel_be(u32 v, unsigned __iomem *p) 101 { 102 out_be32(p, v); 103 } 104 105 static void _fsl_writel_le(u32 v, unsigned __iomem *p) 106 { 107 out_le32(p, v); 108 } 109 110 static u32 (*_fsl_readl)(const unsigned __iomem *p); 111 static void (*_fsl_writel)(u32 v, unsigned __iomem *p); 112 113 #define fsl_readl(p) (*_fsl_readl)((p)) 114 #define fsl_writel(v, p) (*_fsl_writel)((v), (p)) 115 116 static inline void fsl_set_accessors(struct fsl_usb2_platform_data *pdata) 117 { 118 if (pdata->big_endian_mmio) { 119 _fsl_readl = _fsl_readl_be; 120 _fsl_writel = _fsl_writel_be; 121 } else { 122 _fsl_readl = _fsl_readl_le; 123 _fsl_writel = _fsl_writel_le; 124 } 125 } 126 127 static inline u32 cpu_to_hc32(const u32 x) 128 { 129 return udc_controller->pdata->big_endian_desc 130 ? (__force u32)cpu_to_be32(x) 131 : (__force u32)cpu_to_le32(x); 132 } 133 134 static inline u32 hc32_to_cpu(const u32 x) 135 { 136 return udc_controller->pdata->big_endian_desc 137 ? be32_to_cpu((__force __be32)x) 138 : le32_to_cpu((__force __le32)x); 139 } 140 #else /* !CONFIG_PPC32 */ 141 static inline void fsl_set_accessors(struct fsl_usb2_platform_data *pdata) {} 142 143 #define fsl_readl(addr) readl(addr) 144 #define fsl_writel(val32, addr) writel(val32, addr) 145 #define cpu_to_hc32(x) cpu_to_le32(x) 146 #define hc32_to_cpu(x) le32_to_cpu(x) 147 #endif /* CONFIG_PPC32 */ 148 149 /******************************************************************** 150 * Internal Used Function 151 ********************************************************************/ 152 /*----------------------------------------------------------------- 153 * done() - retire a request; caller blocked irqs 154 * @status : request status to be set, only works when 155 * request is still in progress. 156 *--------------------------------------------------------------*/ 157 static void done(struct fsl_ep *ep, struct fsl_req *req, int status) 158 __releases(ep->udc->lock) 159 __acquires(ep->udc->lock) 160 { 161 struct fsl_udc *udc = NULL; 162 unsigned char stopped = ep->stopped; 163 struct ep_td_struct *curr_td, *next_td; 164 int j; 165 166 udc = (struct fsl_udc *)ep->udc; 167 /* Removed the req from fsl_ep->queue */ 168 list_del_init(&req->queue); 169 170 /* req.status should be set as -EINPROGRESS in ep_queue() */ 171 if (req->req.status == -EINPROGRESS) 172 req->req.status = status; 173 else 174 status = req->req.status; 175 176 /* Free dtd for the request */ 177 next_td = req->head; 178 for (j = 0; j < req->dtd_count; j++) { 179 curr_td = next_td; 180 if (j != req->dtd_count - 1) { 181 next_td = curr_td->next_td_virt; 182 } 183 dma_pool_free(udc->td_pool, curr_td, curr_td->td_dma); 184 } 185 186 usb_gadget_unmap_request(&ep->udc->gadget, &req->req, ep_is_in(ep)); 187 188 if (status && (status != -ESHUTDOWN)) 189 VDBG("complete %s req %p stat %d len %u/%u", 190 ep->ep.name, &req->req, status, 191 req->req.actual, req->req.length); 192 193 ep->stopped = 1; 194 195 spin_unlock(&ep->udc->lock); 196 197 usb_gadget_giveback_request(&ep->ep, &req->req); 198 199 spin_lock(&ep->udc->lock); 200 ep->stopped = stopped; 201 } 202 203 /*----------------------------------------------------------------- 204 * nuke(): delete all requests related to this ep 205 * called with spinlock held 206 *--------------------------------------------------------------*/ 207 static void nuke(struct fsl_ep *ep, int status) 208 { 209 ep->stopped = 1; 210 211 /* Flush fifo */ 212 fsl_ep_fifo_flush(&ep->ep); 213 214 /* Whether this eq has request linked */ 215 while (!list_empty(&ep->queue)) { 216 struct fsl_req *req = NULL; 217 218 req = list_entry(ep->queue.next, struct fsl_req, queue); 219 done(ep, req, status); 220 } 221 } 222 223 /*------------------------------------------------------------------ 224 Internal Hardware related function 225 ------------------------------------------------------------------*/ 226 227 static int dr_controller_setup(struct fsl_udc *udc) 228 { 229 unsigned int tmp, portctrl, ep_num; 230 unsigned int max_no_of_ep; 231 unsigned int ctrl; 232 unsigned long timeout; 233 234 #define FSL_UDC_RESET_TIMEOUT 1000 235 236 /* Config PHY interface */ 237 portctrl = fsl_readl(&dr_regs->portsc1); 238 portctrl &= ~(PORTSCX_PHY_TYPE_SEL | PORTSCX_PORT_WIDTH); 239 switch (udc->phy_mode) { 240 case FSL_USB2_PHY_ULPI: 241 if (udc->pdata->have_sysif_regs) { 242 if (udc->pdata->controller_ver) { 243 /* controller version 1.6 or above */ 244 ctrl = __raw_readl(&usb_sys_regs->control); 245 ctrl &= ~USB_CTRL_UTMI_PHY_EN; 246 ctrl |= USB_CTRL_USB_EN; 247 __raw_writel(ctrl, &usb_sys_regs->control); 248 } 249 } 250 portctrl |= PORTSCX_PTS_ULPI; 251 break; 252 case FSL_USB2_PHY_UTMI_WIDE: 253 portctrl |= PORTSCX_PTW_16BIT; 254 /* fall through */ 255 case FSL_USB2_PHY_UTMI: 256 case FSL_USB2_PHY_UTMI_DUAL: 257 if (udc->pdata->have_sysif_regs) { 258 if (udc->pdata->controller_ver) { 259 /* controller version 1.6 or above */ 260 ctrl = __raw_readl(&usb_sys_regs->control); 261 ctrl |= (USB_CTRL_UTMI_PHY_EN | 262 USB_CTRL_USB_EN); 263 __raw_writel(ctrl, &usb_sys_regs->control); 264 mdelay(FSL_UTMI_PHY_DLY); /* Delay for UTMI 265 PHY CLK to become stable - 10ms*/ 266 } 267 } 268 portctrl |= PORTSCX_PTS_UTMI; 269 break; 270 case FSL_USB2_PHY_SERIAL: 271 portctrl |= PORTSCX_PTS_FSLS; 272 break; 273 default: 274 return -EINVAL; 275 } 276 fsl_writel(portctrl, &dr_regs->portsc1); 277 278 /* Stop and reset the usb controller */ 279 tmp = fsl_readl(&dr_regs->usbcmd); 280 tmp &= ~USB_CMD_RUN_STOP; 281 fsl_writel(tmp, &dr_regs->usbcmd); 282 283 tmp = fsl_readl(&dr_regs->usbcmd); 284 tmp |= USB_CMD_CTRL_RESET; 285 fsl_writel(tmp, &dr_regs->usbcmd); 286 287 /* Wait for reset to complete */ 288 timeout = jiffies + FSL_UDC_RESET_TIMEOUT; 289 while (fsl_readl(&dr_regs->usbcmd) & USB_CMD_CTRL_RESET) { 290 if (time_after(jiffies, timeout)) { 291 ERR("udc reset timeout!\n"); 292 return -ETIMEDOUT; 293 } 294 cpu_relax(); 295 } 296 297 /* Set the controller as device mode */ 298 tmp = fsl_readl(&dr_regs->usbmode); 299 tmp &= ~USB_MODE_CTRL_MODE_MASK; /* clear mode bits */ 300 tmp |= USB_MODE_CTRL_MODE_DEVICE; 301 /* Disable Setup Lockout */ 302 tmp |= USB_MODE_SETUP_LOCK_OFF; 303 if (udc->pdata->es) 304 tmp |= USB_MODE_ES; 305 fsl_writel(tmp, &dr_regs->usbmode); 306 307 /* Clear the setup status */ 308 fsl_writel(0, &dr_regs->usbsts); 309 310 tmp = udc->ep_qh_dma; 311 tmp &= USB_EP_LIST_ADDRESS_MASK; 312 fsl_writel(tmp, &dr_regs->endpointlistaddr); 313 314 VDBG("vir[qh_base] is %p phy[qh_base] is 0x%8x reg is 0x%8x", 315 udc->ep_qh, (int)tmp, 316 fsl_readl(&dr_regs->endpointlistaddr)); 317 318 max_no_of_ep = (0x0000001F & fsl_readl(&dr_regs->dccparams)); 319 for (ep_num = 1; ep_num < max_no_of_ep; ep_num++) { 320 tmp = fsl_readl(&dr_regs->endptctrl[ep_num]); 321 tmp &= ~(EPCTRL_TX_TYPE | EPCTRL_RX_TYPE); 322 tmp |= (EPCTRL_EP_TYPE_BULK << EPCTRL_TX_EP_TYPE_SHIFT) 323 | (EPCTRL_EP_TYPE_BULK << EPCTRL_RX_EP_TYPE_SHIFT); 324 fsl_writel(tmp, &dr_regs->endptctrl[ep_num]); 325 } 326 /* Config control enable i/o output, cpu endian register */ 327 #ifndef CONFIG_ARCH_MXC 328 if (udc->pdata->have_sysif_regs) { 329 ctrl = __raw_readl(&usb_sys_regs->control); 330 ctrl |= USB_CTRL_IOENB; 331 __raw_writel(ctrl, &usb_sys_regs->control); 332 } 333 #endif 334 335 #if defined(CONFIG_PPC32) && !defined(CONFIG_NOT_COHERENT_CACHE) 336 /* Turn on cache snooping hardware, since some PowerPC platforms 337 * wholly rely on hardware to deal with cache coherent. */ 338 339 if (udc->pdata->have_sysif_regs) { 340 /* Setup Snooping for all the 4GB space */ 341 tmp = SNOOP_SIZE_2GB; /* starts from 0x0, size 2G */ 342 __raw_writel(tmp, &usb_sys_regs->snoop1); 343 tmp |= 0x80000000; /* starts from 0x8000000, size 2G */ 344 __raw_writel(tmp, &usb_sys_regs->snoop2); 345 } 346 #endif 347 348 return 0; 349 } 350 351 /* Enable DR irq and set controller to run state */ 352 static void dr_controller_run(struct fsl_udc *udc) 353 { 354 u32 temp; 355 356 /* Enable DR irq reg */ 357 temp = USB_INTR_INT_EN | USB_INTR_ERR_INT_EN 358 | USB_INTR_PTC_DETECT_EN | USB_INTR_RESET_EN 359 | USB_INTR_DEVICE_SUSPEND | USB_INTR_SYS_ERR_EN; 360 361 fsl_writel(temp, &dr_regs->usbintr); 362 363 /* Clear stopped bit */ 364 udc->stopped = 0; 365 366 /* Set the controller as device mode */ 367 temp = fsl_readl(&dr_regs->usbmode); 368 temp |= USB_MODE_CTRL_MODE_DEVICE; 369 fsl_writel(temp, &dr_regs->usbmode); 370 371 /* Set controller to Run */ 372 temp = fsl_readl(&dr_regs->usbcmd); 373 temp |= USB_CMD_RUN_STOP; 374 fsl_writel(temp, &dr_regs->usbcmd); 375 } 376 377 static void dr_controller_stop(struct fsl_udc *udc) 378 { 379 unsigned int tmp; 380 381 pr_debug("%s\n", __func__); 382 383 /* if we're in OTG mode, and the Host is currently using the port, 384 * stop now and don't rip the controller out from under the 385 * ehci driver 386 */ 387 if (udc->gadget.is_otg) { 388 if (!(fsl_readl(&dr_regs->otgsc) & OTGSC_STS_USB_ID)) { 389 pr_debug("udc: Leaving early\n"); 390 return; 391 } 392 } 393 394 /* disable all INTR */ 395 fsl_writel(0, &dr_regs->usbintr); 396 397 /* Set stopped bit for isr */ 398 udc->stopped = 1; 399 400 /* disable IO output */ 401 /* usb_sys_regs->control = 0; */ 402 403 /* set controller to Stop */ 404 tmp = fsl_readl(&dr_regs->usbcmd); 405 tmp &= ~USB_CMD_RUN_STOP; 406 fsl_writel(tmp, &dr_regs->usbcmd); 407 } 408 409 static void dr_ep_setup(unsigned char ep_num, unsigned char dir, 410 unsigned char ep_type) 411 { 412 unsigned int tmp_epctrl = 0; 413 414 tmp_epctrl = fsl_readl(&dr_regs->endptctrl[ep_num]); 415 if (dir) { 416 if (ep_num) 417 tmp_epctrl |= EPCTRL_TX_DATA_TOGGLE_RST; 418 tmp_epctrl |= EPCTRL_TX_ENABLE; 419 tmp_epctrl &= ~EPCTRL_TX_TYPE; 420 tmp_epctrl |= ((unsigned int)(ep_type) 421 << EPCTRL_TX_EP_TYPE_SHIFT); 422 } else { 423 if (ep_num) 424 tmp_epctrl |= EPCTRL_RX_DATA_TOGGLE_RST; 425 tmp_epctrl |= EPCTRL_RX_ENABLE; 426 tmp_epctrl &= ~EPCTRL_RX_TYPE; 427 tmp_epctrl |= ((unsigned int)(ep_type) 428 << EPCTRL_RX_EP_TYPE_SHIFT); 429 } 430 431 fsl_writel(tmp_epctrl, &dr_regs->endptctrl[ep_num]); 432 } 433 434 static void 435 dr_ep_change_stall(unsigned char ep_num, unsigned char dir, int value) 436 { 437 u32 tmp_epctrl = 0; 438 439 tmp_epctrl = fsl_readl(&dr_regs->endptctrl[ep_num]); 440 441 if (value) { 442 /* set the stall bit */ 443 if (dir) 444 tmp_epctrl |= EPCTRL_TX_EP_STALL; 445 else 446 tmp_epctrl |= EPCTRL_RX_EP_STALL; 447 } else { 448 /* clear the stall bit and reset data toggle */ 449 if (dir) { 450 tmp_epctrl &= ~EPCTRL_TX_EP_STALL; 451 tmp_epctrl |= EPCTRL_TX_DATA_TOGGLE_RST; 452 } else { 453 tmp_epctrl &= ~EPCTRL_RX_EP_STALL; 454 tmp_epctrl |= EPCTRL_RX_DATA_TOGGLE_RST; 455 } 456 } 457 fsl_writel(tmp_epctrl, &dr_regs->endptctrl[ep_num]); 458 } 459 460 /* Get stall status of a specific ep 461 Return: 0: not stalled; 1:stalled */ 462 static int dr_ep_get_stall(unsigned char ep_num, unsigned char dir) 463 { 464 u32 epctrl; 465 466 epctrl = fsl_readl(&dr_regs->endptctrl[ep_num]); 467 if (dir) 468 return (epctrl & EPCTRL_TX_EP_STALL) ? 1 : 0; 469 else 470 return (epctrl & EPCTRL_RX_EP_STALL) ? 1 : 0; 471 } 472 473 /******************************************************************** 474 Internal Structure Build up functions 475 ********************************************************************/ 476 477 /*------------------------------------------------------------------ 478 * struct_ep_qh_setup(): set the Endpoint Capabilites field of QH 479 * @zlt: Zero Length Termination Select (1: disable; 0: enable) 480 * @mult: Mult field 481 ------------------------------------------------------------------*/ 482 static void struct_ep_qh_setup(struct fsl_udc *udc, unsigned char ep_num, 483 unsigned char dir, unsigned char ep_type, 484 unsigned int max_pkt_len, 485 unsigned int zlt, unsigned char mult) 486 { 487 struct ep_queue_head *p_QH = &udc->ep_qh[2 * ep_num + dir]; 488 unsigned int tmp = 0; 489 490 /* set the Endpoint Capabilites in QH */ 491 switch (ep_type) { 492 case USB_ENDPOINT_XFER_CONTROL: 493 /* Interrupt On Setup (IOS). for control ep */ 494 tmp = (max_pkt_len << EP_QUEUE_HEAD_MAX_PKT_LEN_POS) 495 | EP_QUEUE_HEAD_IOS; 496 break; 497 case USB_ENDPOINT_XFER_ISOC: 498 tmp = (max_pkt_len << EP_QUEUE_HEAD_MAX_PKT_LEN_POS) 499 | (mult << EP_QUEUE_HEAD_MULT_POS); 500 break; 501 case USB_ENDPOINT_XFER_BULK: 502 case USB_ENDPOINT_XFER_INT: 503 tmp = max_pkt_len << EP_QUEUE_HEAD_MAX_PKT_LEN_POS; 504 break; 505 default: 506 VDBG("error ep type is %d", ep_type); 507 return; 508 } 509 if (zlt) 510 tmp |= EP_QUEUE_HEAD_ZLT_SEL; 511 512 p_QH->max_pkt_length = cpu_to_hc32(tmp); 513 p_QH->next_dtd_ptr = 1; 514 p_QH->size_ioc_int_sts = 0; 515 } 516 517 /* Setup qh structure and ep register for ep0. */ 518 static void ep0_setup(struct fsl_udc *udc) 519 { 520 /* the initialization of an ep includes: fields in QH, Regs, 521 * fsl_ep struct */ 522 struct_ep_qh_setup(udc, 0, USB_RECV, USB_ENDPOINT_XFER_CONTROL, 523 USB_MAX_CTRL_PAYLOAD, 0, 0); 524 struct_ep_qh_setup(udc, 0, USB_SEND, USB_ENDPOINT_XFER_CONTROL, 525 USB_MAX_CTRL_PAYLOAD, 0, 0); 526 dr_ep_setup(0, USB_RECV, USB_ENDPOINT_XFER_CONTROL); 527 dr_ep_setup(0, USB_SEND, USB_ENDPOINT_XFER_CONTROL); 528 529 return; 530 531 } 532 533 /*********************************************************************** 534 Endpoint Management Functions 535 ***********************************************************************/ 536 537 /*------------------------------------------------------------------------- 538 * when configurations are set, or when interface settings change 539 * for example the do_set_interface() in gadget layer, 540 * the driver will enable or disable the relevant endpoints 541 * ep0 doesn't use this routine. It is always enabled. 542 -------------------------------------------------------------------------*/ 543 static int fsl_ep_enable(struct usb_ep *_ep, 544 const struct usb_endpoint_descriptor *desc) 545 { 546 struct fsl_udc *udc = NULL; 547 struct fsl_ep *ep = NULL; 548 unsigned short max = 0; 549 unsigned char mult = 0, zlt; 550 int retval = -EINVAL; 551 unsigned long flags = 0; 552 553 ep = container_of(_ep, struct fsl_ep, ep); 554 555 /* catch various bogus parameters */ 556 if (!_ep || !desc 557 || (desc->bDescriptorType != USB_DT_ENDPOINT)) 558 return -EINVAL; 559 560 udc = ep->udc; 561 562 if (!udc->driver || (udc->gadget.speed == USB_SPEED_UNKNOWN)) 563 return -ESHUTDOWN; 564 565 max = usb_endpoint_maxp(desc); 566 567 /* Disable automatic zlp generation. Driver is responsible to indicate 568 * explicitly through req->req.zero. This is needed to enable multi-td 569 * request. */ 570 zlt = 1; 571 572 /* Assume the max packet size from gadget is always correct */ 573 switch (desc->bmAttributes & 0x03) { 574 case USB_ENDPOINT_XFER_CONTROL: 575 case USB_ENDPOINT_XFER_BULK: 576 case USB_ENDPOINT_XFER_INT: 577 /* mult = 0. Execute N Transactions as demonstrated by 578 * the USB variable length packet protocol where N is 579 * computed using the Maximum Packet Length (dQH) and 580 * the Total Bytes field (dTD) */ 581 mult = 0; 582 break; 583 case USB_ENDPOINT_XFER_ISOC: 584 /* Calculate transactions needed for high bandwidth iso */ 585 mult = usb_endpoint_maxp_mult(desc); 586 /* 3 transactions at most */ 587 if (mult > 3) 588 goto en_done; 589 break; 590 default: 591 goto en_done; 592 } 593 594 spin_lock_irqsave(&udc->lock, flags); 595 ep->ep.maxpacket = max; 596 ep->ep.desc = desc; 597 ep->stopped = 0; 598 599 /* Controller related setup */ 600 /* Init EPx Queue Head (Ep Capabilites field in QH 601 * according to max, zlt, mult) */ 602 struct_ep_qh_setup(udc, (unsigned char) ep_index(ep), 603 (unsigned char) ((desc->bEndpointAddress & USB_DIR_IN) 604 ? USB_SEND : USB_RECV), 605 (unsigned char) (desc->bmAttributes 606 & USB_ENDPOINT_XFERTYPE_MASK), 607 max, zlt, mult); 608 609 /* Init endpoint ctrl register */ 610 dr_ep_setup((unsigned char) ep_index(ep), 611 (unsigned char) ((desc->bEndpointAddress & USB_DIR_IN) 612 ? USB_SEND : USB_RECV), 613 (unsigned char) (desc->bmAttributes 614 & USB_ENDPOINT_XFERTYPE_MASK)); 615 616 spin_unlock_irqrestore(&udc->lock, flags); 617 retval = 0; 618 619 VDBG("enabled %s (ep%d%s) maxpacket %d",ep->ep.name, 620 ep->ep.desc->bEndpointAddress & 0x0f, 621 (desc->bEndpointAddress & USB_DIR_IN) 622 ? "in" : "out", max); 623 en_done: 624 return retval; 625 } 626 627 /*--------------------------------------------------------------------- 628 * @ep : the ep being unconfigured. May not be ep0 629 * Any pending and uncomplete req will complete with status (-ESHUTDOWN) 630 *---------------------------------------------------------------------*/ 631 static int fsl_ep_disable(struct usb_ep *_ep) 632 { 633 struct fsl_udc *udc = NULL; 634 struct fsl_ep *ep = NULL; 635 unsigned long flags = 0; 636 u32 epctrl; 637 int ep_num; 638 639 ep = container_of(_ep, struct fsl_ep, ep); 640 if (!_ep || !ep->ep.desc) { 641 VDBG("%s not enabled", _ep ? ep->ep.name : NULL); 642 return -EINVAL; 643 } 644 645 /* disable ep on controller */ 646 ep_num = ep_index(ep); 647 epctrl = fsl_readl(&dr_regs->endptctrl[ep_num]); 648 if (ep_is_in(ep)) { 649 epctrl &= ~(EPCTRL_TX_ENABLE | EPCTRL_TX_TYPE); 650 epctrl |= EPCTRL_EP_TYPE_BULK << EPCTRL_TX_EP_TYPE_SHIFT; 651 } else { 652 epctrl &= ~(EPCTRL_RX_ENABLE | EPCTRL_TX_TYPE); 653 epctrl |= EPCTRL_EP_TYPE_BULK << EPCTRL_RX_EP_TYPE_SHIFT; 654 } 655 fsl_writel(epctrl, &dr_regs->endptctrl[ep_num]); 656 657 udc = (struct fsl_udc *)ep->udc; 658 spin_lock_irqsave(&udc->lock, flags); 659 660 /* nuke all pending requests (does flush) */ 661 nuke(ep, -ESHUTDOWN); 662 663 ep->ep.desc = NULL; 664 ep->stopped = 1; 665 spin_unlock_irqrestore(&udc->lock, flags); 666 667 VDBG("disabled %s OK", _ep->name); 668 return 0; 669 } 670 671 /*--------------------------------------------------------------------- 672 * allocate a request object used by this endpoint 673 * the main operation is to insert the req->queue to the eq->queue 674 * Returns the request, or null if one could not be allocated 675 *---------------------------------------------------------------------*/ 676 static struct usb_request * 677 fsl_alloc_request(struct usb_ep *_ep, gfp_t gfp_flags) 678 { 679 struct fsl_req *req = NULL; 680 681 req = kzalloc(sizeof *req, gfp_flags); 682 if (!req) 683 return NULL; 684 685 req->req.dma = DMA_ADDR_INVALID; 686 INIT_LIST_HEAD(&req->queue); 687 688 return &req->req; 689 } 690 691 static void fsl_free_request(struct usb_ep *_ep, struct usb_request *_req) 692 { 693 struct fsl_req *req = NULL; 694 695 req = container_of(_req, struct fsl_req, req); 696 697 if (_req) 698 kfree(req); 699 } 700 701 /* Actually add a dTD chain to an empty dQH and let go */ 702 static void fsl_prime_ep(struct fsl_ep *ep, struct ep_td_struct *td) 703 { 704 struct ep_queue_head *qh = get_qh_by_ep(ep); 705 706 /* Write dQH next pointer and terminate bit to 0 */ 707 qh->next_dtd_ptr = cpu_to_hc32(td->td_dma 708 & EP_QUEUE_HEAD_NEXT_POINTER_MASK); 709 710 /* Clear active and halt bit */ 711 qh->size_ioc_int_sts &= cpu_to_hc32(~(EP_QUEUE_HEAD_STATUS_ACTIVE 712 | EP_QUEUE_HEAD_STATUS_HALT)); 713 714 /* Ensure that updates to the QH will occur before priming. */ 715 wmb(); 716 717 /* Prime endpoint by writing correct bit to ENDPTPRIME */ 718 fsl_writel(ep_is_in(ep) ? (1 << (ep_index(ep) + 16)) 719 : (1 << (ep_index(ep))), &dr_regs->endpointprime); 720 } 721 722 /* Add dTD chain to the dQH of an EP */ 723 static void fsl_queue_td(struct fsl_ep *ep, struct fsl_req *req) 724 { 725 u32 temp, bitmask, tmp_stat; 726 727 /* VDBG("QH addr Register 0x%8x", dr_regs->endpointlistaddr); 728 VDBG("ep_qh[%d] addr is 0x%8x", i, (u32)&(ep->udc->ep_qh[i])); */ 729 730 bitmask = ep_is_in(ep) 731 ? (1 << (ep_index(ep) + 16)) 732 : (1 << (ep_index(ep))); 733 734 /* check if the pipe is empty */ 735 if (!(list_empty(&ep->queue)) && !(ep_index(ep) == 0)) { 736 /* Add td to the end */ 737 struct fsl_req *lastreq; 738 lastreq = list_entry(ep->queue.prev, struct fsl_req, queue); 739 lastreq->tail->next_td_ptr = 740 cpu_to_hc32(req->head->td_dma & DTD_ADDR_MASK); 741 /* Ensure dTD's next dtd pointer to be updated */ 742 wmb(); 743 /* Read prime bit, if 1 goto done */ 744 if (fsl_readl(&dr_regs->endpointprime) & bitmask) 745 return; 746 747 do { 748 /* Set ATDTW bit in USBCMD */ 749 temp = fsl_readl(&dr_regs->usbcmd); 750 fsl_writel(temp | USB_CMD_ATDTW, &dr_regs->usbcmd); 751 752 /* Read correct status bit */ 753 tmp_stat = fsl_readl(&dr_regs->endptstatus) & bitmask; 754 755 } while (!(fsl_readl(&dr_regs->usbcmd) & USB_CMD_ATDTW)); 756 757 /* Write ATDTW bit to 0 */ 758 temp = fsl_readl(&dr_regs->usbcmd); 759 fsl_writel(temp & ~USB_CMD_ATDTW, &dr_regs->usbcmd); 760 761 if (tmp_stat) 762 return; 763 } 764 765 fsl_prime_ep(ep, req->head); 766 } 767 768 /* Fill in the dTD structure 769 * @req: request that the transfer belongs to 770 * @length: return actually data length of the dTD 771 * @dma: return dma address of the dTD 772 * @is_last: return flag if it is the last dTD of the request 773 * return: pointer to the built dTD */ 774 static struct ep_td_struct *fsl_build_dtd(struct fsl_req *req, unsigned *length, 775 dma_addr_t *dma, int *is_last, gfp_t gfp_flags) 776 { 777 u32 swap_temp; 778 struct ep_td_struct *dtd; 779 780 /* how big will this transfer be? */ 781 *length = min(req->req.length - req->req.actual, 782 (unsigned)EP_MAX_LENGTH_TRANSFER); 783 784 dtd = dma_pool_alloc(udc_controller->td_pool, gfp_flags, dma); 785 if (dtd == NULL) 786 return dtd; 787 788 dtd->td_dma = *dma; 789 /* Clear reserved field */ 790 swap_temp = hc32_to_cpu(dtd->size_ioc_sts); 791 swap_temp &= ~DTD_RESERVED_FIELDS; 792 dtd->size_ioc_sts = cpu_to_hc32(swap_temp); 793 794 /* Init all of buffer page pointers */ 795 swap_temp = (u32) (req->req.dma + req->req.actual); 796 dtd->buff_ptr0 = cpu_to_hc32(swap_temp); 797 dtd->buff_ptr1 = cpu_to_hc32(swap_temp + 0x1000); 798 dtd->buff_ptr2 = cpu_to_hc32(swap_temp + 0x2000); 799 dtd->buff_ptr3 = cpu_to_hc32(swap_temp + 0x3000); 800 dtd->buff_ptr4 = cpu_to_hc32(swap_temp + 0x4000); 801 802 req->req.actual += *length; 803 804 /* zlp is needed if req->req.zero is set */ 805 if (req->req.zero) { 806 if (*length == 0 || (*length % req->ep->ep.maxpacket) != 0) 807 *is_last = 1; 808 else 809 *is_last = 0; 810 } else if (req->req.length == req->req.actual) 811 *is_last = 1; 812 else 813 *is_last = 0; 814 815 if ((*is_last) == 0) 816 VDBG("multi-dtd request!"); 817 /* Fill in the transfer size; set active bit */ 818 swap_temp = ((*length << DTD_LENGTH_BIT_POS) | DTD_STATUS_ACTIVE); 819 820 /* Enable interrupt for the last dtd of a request */ 821 if (*is_last && !req->req.no_interrupt) 822 swap_temp |= DTD_IOC; 823 824 dtd->size_ioc_sts = cpu_to_hc32(swap_temp); 825 826 mb(); 827 828 VDBG("length = %d address= 0x%x", *length, (int)*dma); 829 830 return dtd; 831 } 832 833 /* Generate dtd chain for a request */ 834 static int fsl_req_to_dtd(struct fsl_req *req, gfp_t gfp_flags) 835 { 836 unsigned count; 837 int is_last; 838 int is_first =1; 839 struct ep_td_struct *last_dtd = NULL, *dtd; 840 dma_addr_t dma; 841 842 do { 843 dtd = fsl_build_dtd(req, &count, &dma, &is_last, gfp_flags); 844 if (dtd == NULL) 845 return -ENOMEM; 846 847 if (is_first) { 848 is_first = 0; 849 req->head = dtd; 850 } else { 851 last_dtd->next_td_ptr = cpu_to_hc32(dma); 852 last_dtd->next_td_virt = dtd; 853 } 854 last_dtd = dtd; 855 856 req->dtd_count++; 857 } while (!is_last); 858 859 dtd->next_td_ptr = cpu_to_hc32(DTD_NEXT_TERMINATE); 860 861 req->tail = dtd; 862 863 return 0; 864 } 865 866 /* queues (submits) an I/O request to an endpoint */ 867 static int 868 fsl_ep_queue(struct usb_ep *_ep, struct usb_request *_req, gfp_t gfp_flags) 869 { 870 struct fsl_ep *ep = container_of(_ep, struct fsl_ep, ep); 871 struct fsl_req *req = container_of(_req, struct fsl_req, req); 872 struct fsl_udc *udc; 873 unsigned long flags; 874 int ret; 875 876 /* catch various bogus parameters */ 877 if (!_req || !req->req.complete || !req->req.buf 878 || !list_empty(&req->queue)) { 879 VDBG("%s, bad params", __func__); 880 return -EINVAL; 881 } 882 if (unlikely(!_ep || !ep->ep.desc)) { 883 VDBG("%s, bad ep", __func__); 884 return -EINVAL; 885 } 886 if (usb_endpoint_xfer_isoc(ep->ep.desc)) { 887 if (req->req.length > ep->ep.maxpacket) 888 return -EMSGSIZE; 889 } 890 891 udc = ep->udc; 892 if (!udc->driver || udc->gadget.speed == USB_SPEED_UNKNOWN) 893 return -ESHUTDOWN; 894 895 req->ep = ep; 896 897 ret = usb_gadget_map_request(&ep->udc->gadget, &req->req, ep_is_in(ep)); 898 if (ret) 899 return ret; 900 901 req->req.status = -EINPROGRESS; 902 req->req.actual = 0; 903 req->dtd_count = 0; 904 905 /* build dtds and push them to device queue */ 906 if (!fsl_req_to_dtd(req, gfp_flags)) { 907 spin_lock_irqsave(&udc->lock, flags); 908 fsl_queue_td(ep, req); 909 } else { 910 return -ENOMEM; 911 } 912 913 /* irq handler advances the queue */ 914 if (req != NULL) 915 list_add_tail(&req->queue, &ep->queue); 916 spin_unlock_irqrestore(&udc->lock, flags); 917 918 return 0; 919 } 920 921 /* dequeues (cancels, unlinks) an I/O request from an endpoint */ 922 static int fsl_ep_dequeue(struct usb_ep *_ep, struct usb_request *_req) 923 { 924 struct fsl_ep *ep = container_of(_ep, struct fsl_ep, ep); 925 struct fsl_req *req; 926 unsigned long flags; 927 int ep_num, stopped, ret = 0; 928 u32 epctrl; 929 930 if (!_ep || !_req) 931 return -EINVAL; 932 933 spin_lock_irqsave(&ep->udc->lock, flags); 934 stopped = ep->stopped; 935 936 /* Stop the ep before we deal with the queue */ 937 ep->stopped = 1; 938 ep_num = ep_index(ep); 939 epctrl = fsl_readl(&dr_regs->endptctrl[ep_num]); 940 if (ep_is_in(ep)) 941 epctrl &= ~EPCTRL_TX_ENABLE; 942 else 943 epctrl &= ~EPCTRL_RX_ENABLE; 944 fsl_writel(epctrl, &dr_regs->endptctrl[ep_num]); 945 946 /* make sure it's actually queued on this endpoint */ 947 list_for_each_entry(req, &ep->queue, queue) { 948 if (&req->req == _req) 949 break; 950 } 951 if (&req->req != _req) { 952 ret = -EINVAL; 953 goto out; 954 } 955 956 /* The request is in progress, or completed but not dequeued */ 957 if (ep->queue.next == &req->queue) { 958 _req->status = -ECONNRESET; 959 fsl_ep_fifo_flush(_ep); /* flush current transfer */ 960 961 /* The request isn't the last request in this ep queue */ 962 if (req->queue.next != &ep->queue) { 963 struct fsl_req *next_req; 964 965 next_req = list_entry(req->queue.next, struct fsl_req, 966 queue); 967 968 /* prime with dTD of next request */ 969 fsl_prime_ep(ep, next_req->head); 970 } 971 /* The request hasn't been processed, patch up the TD chain */ 972 } else { 973 struct fsl_req *prev_req; 974 975 prev_req = list_entry(req->queue.prev, struct fsl_req, queue); 976 prev_req->tail->next_td_ptr = req->tail->next_td_ptr; 977 } 978 979 done(ep, req, -ECONNRESET); 980 981 /* Enable EP */ 982 out: epctrl = fsl_readl(&dr_regs->endptctrl[ep_num]); 983 if (ep_is_in(ep)) 984 epctrl |= EPCTRL_TX_ENABLE; 985 else 986 epctrl |= EPCTRL_RX_ENABLE; 987 fsl_writel(epctrl, &dr_regs->endptctrl[ep_num]); 988 ep->stopped = stopped; 989 990 spin_unlock_irqrestore(&ep->udc->lock, flags); 991 return ret; 992 } 993 994 /*-------------------------------------------------------------------------*/ 995 996 /*----------------------------------------------------------------- 997 * modify the endpoint halt feature 998 * @ep: the non-isochronous endpoint being stalled 999 * @value: 1--set halt 0--clear halt 1000 * Returns zero, or a negative error code. 1001 *----------------------------------------------------------------*/ 1002 static int fsl_ep_set_halt(struct usb_ep *_ep, int value) 1003 { 1004 struct fsl_ep *ep = NULL; 1005 unsigned long flags = 0; 1006 int status = -EOPNOTSUPP; /* operation not supported */ 1007 unsigned char ep_dir = 0, ep_num = 0; 1008 struct fsl_udc *udc = NULL; 1009 1010 ep = container_of(_ep, struct fsl_ep, ep); 1011 udc = ep->udc; 1012 if (!_ep || !ep->ep.desc) { 1013 status = -EINVAL; 1014 goto out; 1015 } 1016 1017 if (usb_endpoint_xfer_isoc(ep->ep.desc)) { 1018 status = -EOPNOTSUPP; 1019 goto out; 1020 } 1021 1022 /* Attempt to halt IN ep will fail if any transfer requests 1023 * are still queue */ 1024 if (value && ep_is_in(ep) && !list_empty(&ep->queue)) { 1025 status = -EAGAIN; 1026 goto out; 1027 } 1028 1029 status = 0; 1030 ep_dir = ep_is_in(ep) ? USB_SEND : USB_RECV; 1031 ep_num = (unsigned char)(ep_index(ep)); 1032 spin_lock_irqsave(&ep->udc->lock, flags); 1033 dr_ep_change_stall(ep_num, ep_dir, value); 1034 spin_unlock_irqrestore(&ep->udc->lock, flags); 1035 1036 if (ep_index(ep) == 0) { 1037 udc->ep0_state = WAIT_FOR_SETUP; 1038 udc->ep0_dir = 0; 1039 } 1040 out: 1041 VDBG(" %s %s halt stat %d", ep->ep.name, 1042 value ? "set" : "clear", status); 1043 1044 return status; 1045 } 1046 1047 static int fsl_ep_fifo_status(struct usb_ep *_ep) 1048 { 1049 struct fsl_ep *ep; 1050 struct fsl_udc *udc; 1051 int size = 0; 1052 u32 bitmask; 1053 struct ep_queue_head *qh; 1054 1055 ep = container_of(_ep, struct fsl_ep, ep); 1056 if (!_ep || (!ep->ep.desc && ep_index(ep) != 0)) 1057 return -ENODEV; 1058 1059 udc = (struct fsl_udc *)ep->udc; 1060 1061 if (!udc->driver || udc->gadget.speed == USB_SPEED_UNKNOWN) 1062 return -ESHUTDOWN; 1063 1064 qh = get_qh_by_ep(ep); 1065 1066 bitmask = (ep_is_in(ep)) ? (1 << (ep_index(ep) + 16)) : 1067 (1 << (ep_index(ep))); 1068 1069 if (fsl_readl(&dr_regs->endptstatus) & bitmask) 1070 size = (qh->size_ioc_int_sts & DTD_PACKET_SIZE) 1071 >> DTD_LENGTH_BIT_POS; 1072 1073 pr_debug("%s %u\n", __func__, size); 1074 return size; 1075 } 1076 1077 static void fsl_ep_fifo_flush(struct usb_ep *_ep) 1078 { 1079 struct fsl_ep *ep; 1080 int ep_num, ep_dir; 1081 u32 bits; 1082 unsigned long timeout; 1083 #define FSL_UDC_FLUSH_TIMEOUT 1000 1084 1085 if (!_ep) { 1086 return; 1087 } else { 1088 ep = container_of(_ep, struct fsl_ep, ep); 1089 if (!ep->ep.desc) 1090 return; 1091 } 1092 ep_num = ep_index(ep); 1093 ep_dir = ep_is_in(ep) ? USB_SEND : USB_RECV; 1094 1095 if (ep_num == 0) 1096 bits = (1 << 16) | 1; 1097 else if (ep_dir == USB_SEND) 1098 bits = 1 << (16 + ep_num); 1099 else 1100 bits = 1 << ep_num; 1101 1102 timeout = jiffies + FSL_UDC_FLUSH_TIMEOUT; 1103 do { 1104 fsl_writel(bits, &dr_regs->endptflush); 1105 1106 /* Wait until flush complete */ 1107 while (fsl_readl(&dr_regs->endptflush)) { 1108 if (time_after(jiffies, timeout)) { 1109 ERR("ep flush timeout\n"); 1110 return; 1111 } 1112 cpu_relax(); 1113 } 1114 /* See if we need to flush again */ 1115 } while (fsl_readl(&dr_regs->endptstatus) & bits); 1116 } 1117 1118 static const struct usb_ep_ops fsl_ep_ops = { 1119 .enable = fsl_ep_enable, 1120 .disable = fsl_ep_disable, 1121 1122 .alloc_request = fsl_alloc_request, 1123 .free_request = fsl_free_request, 1124 1125 .queue = fsl_ep_queue, 1126 .dequeue = fsl_ep_dequeue, 1127 1128 .set_halt = fsl_ep_set_halt, 1129 .fifo_status = fsl_ep_fifo_status, 1130 .fifo_flush = fsl_ep_fifo_flush, /* flush fifo */ 1131 }; 1132 1133 /*------------------------------------------------------------------------- 1134 Gadget Driver Layer Operations 1135 -------------------------------------------------------------------------*/ 1136 1137 /*---------------------------------------------------------------------- 1138 * Get the current frame number (from DR frame_index Reg ) 1139 *----------------------------------------------------------------------*/ 1140 static int fsl_get_frame(struct usb_gadget *gadget) 1141 { 1142 return (int)(fsl_readl(&dr_regs->frindex) & USB_FRINDEX_MASKS); 1143 } 1144 1145 /*----------------------------------------------------------------------- 1146 * Tries to wake up the host connected to this gadget 1147 -----------------------------------------------------------------------*/ 1148 static int fsl_wakeup(struct usb_gadget *gadget) 1149 { 1150 struct fsl_udc *udc = container_of(gadget, struct fsl_udc, gadget); 1151 u32 portsc; 1152 1153 /* Remote wakeup feature not enabled by host */ 1154 if (!udc->remote_wakeup) 1155 return -ENOTSUPP; 1156 1157 portsc = fsl_readl(&dr_regs->portsc1); 1158 /* not suspended? */ 1159 if (!(portsc & PORTSCX_PORT_SUSPEND)) 1160 return 0; 1161 /* trigger force resume */ 1162 portsc |= PORTSCX_PORT_FORCE_RESUME; 1163 fsl_writel(portsc, &dr_regs->portsc1); 1164 return 0; 1165 } 1166 1167 static int can_pullup(struct fsl_udc *udc) 1168 { 1169 return udc->driver && udc->softconnect && udc->vbus_active; 1170 } 1171 1172 /* Notify controller that VBUS is powered, Called by whatever 1173 detects VBUS sessions */ 1174 static int fsl_vbus_session(struct usb_gadget *gadget, int is_active) 1175 { 1176 struct fsl_udc *udc; 1177 unsigned long flags; 1178 1179 udc = container_of(gadget, struct fsl_udc, gadget); 1180 spin_lock_irqsave(&udc->lock, flags); 1181 VDBG("VBUS %s", is_active ? "on" : "off"); 1182 udc->vbus_active = (is_active != 0); 1183 if (can_pullup(udc)) 1184 fsl_writel((fsl_readl(&dr_regs->usbcmd) | USB_CMD_RUN_STOP), 1185 &dr_regs->usbcmd); 1186 else 1187 fsl_writel((fsl_readl(&dr_regs->usbcmd) & ~USB_CMD_RUN_STOP), 1188 &dr_regs->usbcmd); 1189 spin_unlock_irqrestore(&udc->lock, flags); 1190 return 0; 1191 } 1192 1193 /* constrain controller's VBUS power usage 1194 * This call is used by gadget drivers during SET_CONFIGURATION calls, 1195 * reporting how much power the device may consume. For example, this 1196 * could affect how quickly batteries are recharged. 1197 * 1198 * Returns zero on success, else negative errno. 1199 */ 1200 static int fsl_vbus_draw(struct usb_gadget *gadget, unsigned mA) 1201 { 1202 struct fsl_udc *udc; 1203 1204 udc = container_of(gadget, struct fsl_udc, gadget); 1205 if (!IS_ERR_OR_NULL(udc->transceiver)) 1206 return usb_phy_set_power(udc->transceiver, mA); 1207 return -ENOTSUPP; 1208 } 1209 1210 /* Change Data+ pullup status 1211 * this func is used by usb_gadget_connect/disconnet 1212 */ 1213 static int fsl_pullup(struct usb_gadget *gadget, int is_on) 1214 { 1215 struct fsl_udc *udc; 1216 1217 udc = container_of(gadget, struct fsl_udc, gadget); 1218 1219 if (!udc->vbus_active) 1220 return -EOPNOTSUPP; 1221 1222 udc->softconnect = (is_on != 0); 1223 if (can_pullup(udc)) 1224 fsl_writel((fsl_readl(&dr_regs->usbcmd) | USB_CMD_RUN_STOP), 1225 &dr_regs->usbcmd); 1226 else 1227 fsl_writel((fsl_readl(&dr_regs->usbcmd) & ~USB_CMD_RUN_STOP), 1228 &dr_regs->usbcmd); 1229 1230 return 0; 1231 } 1232 1233 static int fsl_udc_start(struct usb_gadget *g, 1234 struct usb_gadget_driver *driver); 1235 static int fsl_udc_stop(struct usb_gadget *g); 1236 1237 static const struct usb_gadget_ops fsl_gadget_ops = { 1238 .get_frame = fsl_get_frame, 1239 .wakeup = fsl_wakeup, 1240 /* .set_selfpowered = fsl_set_selfpowered, */ /* Always selfpowered */ 1241 .vbus_session = fsl_vbus_session, 1242 .vbus_draw = fsl_vbus_draw, 1243 .pullup = fsl_pullup, 1244 .udc_start = fsl_udc_start, 1245 .udc_stop = fsl_udc_stop, 1246 }; 1247 1248 /* 1249 * Empty complete function used by this driver to fill in the req->complete 1250 * field when creating a request since the complete field is mandatory. 1251 */ 1252 static void fsl_noop_complete(struct usb_ep *ep, struct usb_request *req) { } 1253 1254 /* Set protocol stall on ep0, protocol stall will automatically be cleared 1255 on new transaction */ 1256 static void ep0stall(struct fsl_udc *udc) 1257 { 1258 u32 tmp; 1259 1260 /* must set tx and rx to stall at the same time */ 1261 tmp = fsl_readl(&dr_regs->endptctrl[0]); 1262 tmp |= EPCTRL_TX_EP_STALL | EPCTRL_RX_EP_STALL; 1263 fsl_writel(tmp, &dr_regs->endptctrl[0]); 1264 udc->ep0_state = WAIT_FOR_SETUP; 1265 udc->ep0_dir = 0; 1266 } 1267 1268 /* Prime a status phase for ep0 */ 1269 static int ep0_prime_status(struct fsl_udc *udc, int direction) 1270 { 1271 struct fsl_req *req = udc->status_req; 1272 struct fsl_ep *ep; 1273 int ret; 1274 1275 if (direction == EP_DIR_IN) 1276 udc->ep0_dir = USB_DIR_IN; 1277 else 1278 udc->ep0_dir = USB_DIR_OUT; 1279 1280 ep = &udc->eps[0]; 1281 if (udc->ep0_state != DATA_STATE_XMIT) 1282 udc->ep0_state = WAIT_FOR_OUT_STATUS; 1283 1284 req->ep = ep; 1285 req->req.length = 0; 1286 req->req.status = -EINPROGRESS; 1287 req->req.actual = 0; 1288 req->req.complete = fsl_noop_complete; 1289 req->dtd_count = 0; 1290 1291 ret = usb_gadget_map_request(&ep->udc->gadget, &req->req, ep_is_in(ep)); 1292 if (ret) 1293 return ret; 1294 1295 if (fsl_req_to_dtd(req, GFP_ATOMIC) == 0) 1296 fsl_queue_td(ep, req); 1297 else 1298 return -ENOMEM; 1299 1300 list_add_tail(&req->queue, &ep->queue); 1301 1302 return 0; 1303 } 1304 1305 static void udc_reset_ep_queue(struct fsl_udc *udc, u8 pipe) 1306 { 1307 struct fsl_ep *ep = get_ep_by_pipe(udc, pipe); 1308 1309 if (ep->ep.name) 1310 nuke(ep, -ESHUTDOWN); 1311 } 1312 1313 /* 1314 * ch9 Set address 1315 */ 1316 static void ch9setaddress(struct fsl_udc *udc, u16 value, u16 index, u16 length) 1317 { 1318 /* Save the new address to device struct */ 1319 udc->device_address = (u8) value; 1320 /* Update usb state */ 1321 udc->usb_state = USB_STATE_ADDRESS; 1322 /* Status phase */ 1323 if (ep0_prime_status(udc, EP_DIR_IN)) 1324 ep0stall(udc); 1325 } 1326 1327 /* 1328 * ch9 Get status 1329 */ 1330 static void ch9getstatus(struct fsl_udc *udc, u8 request_type, u16 value, 1331 u16 index, u16 length) 1332 { 1333 u16 tmp = 0; /* Status, cpu endian */ 1334 struct fsl_req *req; 1335 struct fsl_ep *ep; 1336 int ret; 1337 1338 ep = &udc->eps[0]; 1339 1340 if ((request_type & USB_RECIP_MASK) == USB_RECIP_DEVICE) { 1341 /* Get device status */ 1342 tmp = udc->gadget.is_selfpowered; 1343 tmp |= udc->remote_wakeup << USB_DEVICE_REMOTE_WAKEUP; 1344 } else if ((request_type & USB_RECIP_MASK) == USB_RECIP_INTERFACE) { 1345 /* Get interface status */ 1346 /* We don't have interface information in udc driver */ 1347 tmp = 0; 1348 } else if ((request_type & USB_RECIP_MASK) == USB_RECIP_ENDPOINT) { 1349 /* Get endpoint status */ 1350 struct fsl_ep *target_ep; 1351 1352 target_ep = get_ep_by_pipe(udc, get_pipe_by_windex(index)); 1353 1354 /* stall if endpoint doesn't exist */ 1355 if (!target_ep->ep.desc) 1356 goto stall; 1357 tmp = dr_ep_get_stall(ep_index(target_ep), ep_is_in(target_ep)) 1358 << USB_ENDPOINT_HALT; 1359 } 1360 1361 udc->ep0_dir = USB_DIR_IN; 1362 /* Borrow the per device status_req */ 1363 req = udc->status_req; 1364 /* Fill in the reqest structure */ 1365 *((u16 *) req->req.buf) = cpu_to_le16(tmp); 1366 1367 req->ep = ep; 1368 req->req.length = 2; 1369 req->req.status = -EINPROGRESS; 1370 req->req.actual = 0; 1371 req->req.complete = fsl_noop_complete; 1372 req->dtd_count = 0; 1373 1374 ret = usb_gadget_map_request(&ep->udc->gadget, &req->req, ep_is_in(ep)); 1375 if (ret) 1376 goto stall; 1377 1378 /* prime the data phase */ 1379 if ((fsl_req_to_dtd(req, GFP_ATOMIC) == 0)) 1380 fsl_queue_td(ep, req); 1381 else /* no mem */ 1382 goto stall; 1383 1384 list_add_tail(&req->queue, &ep->queue); 1385 udc->ep0_state = DATA_STATE_XMIT; 1386 if (ep0_prime_status(udc, EP_DIR_OUT)) 1387 ep0stall(udc); 1388 1389 return; 1390 stall: 1391 ep0stall(udc); 1392 } 1393 1394 static void setup_received_irq(struct fsl_udc *udc, 1395 struct usb_ctrlrequest *setup) 1396 __releases(udc->lock) 1397 __acquires(udc->lock) 1398 { 1399 u16 wValue = le16_to_cpu(setup->wValue); 1400 u16 wIndex = le16_to_cpu(setup->wIndex); 1401 u16 wLength = le16_to_cpu(setup->wLength); 1402 1403 udc_reset_ep_queue(udc, 0); 1404 1405 /* We process some stardard setup requests here */ 1406 switch (setup->bRequest) { 1407 case USB_REQ_GET_STATUS: 1408 /* Data+Status phase from udc */ 1409 if ((setup->bRequestType & (USB_DIR_IN | USB_TYPE_MASK)) 1410 != (USB_DIR_IN | USB_TYPE_STANDARD)) 1411 break; 1412 ch9getstatus(udc, setup->bRequestType, wValue, wIndex, wLength); 1413 return; 1414 1415 case USB_REQ_SET_ADDRESS: 1416 /* Status phase from udc */ 1417 if (setup->bRequestType != (USB_DIR_OUT | USB_TYPE_STANDARD 1418 | USB_RECIP_DEVICE)) 1419 break; 1420 ch9setaddress(udc, wValue, wIndex, wLength); 1421 return; 1422 1423 case USB_REQ_CLEAR_FEATURE: 1424 case USB_REQ_SET_FEATURE: 1425 /* Status phase from udc */ 1426 { 1427 int rc = -EOPNOTSUPP; 1428 u16 ptc = 0; 1429 1430 if ((setup->bRequestType & (USB_RECIP_MASK | USB_TYPE_MASK)) 1431 == (USB_RECIP_ENDPOINT | USB_TYPE_STANDARD)) { 1432 int pipe = get_pipe_by_windex(wIndex); 1433 struct fsl_ep *ep; 1434 1435 if (wValue != 0 || wLength != 0 || pipe >= udc->max_ep) 1436 break; 1437 ep = get_ep_by_pipe(udc, pipe); 1438 1439 spin_unlock(&udc->lock); 1440 rc = fsl_ep_set_halt(&ep->ep, 1441 (setup->bRequest == USB_REQ_SET_FEATURE) 1442 ? 1 : 0); 1443 spin_lock(&udc->lock); 1444 1445 } else if ((setup->bRequestType & (USB_RECIP_MASK 1446 | USB_TYPE_MASK)) == (USB_RECIP_DEVICE 1447 | USB_TYPE_STANDARD)) { 1448 /* Note: The driver has not include OTG support yet. 1449 * This will be set when OTG support is added */ 1450 if (wValue == USB_DEVICE_TEST_MODE) 1451 ptc = wIndex >> 8; 1452 else if (gadget_is_otg(&udc->gadget)) { 1453 if (setup->bRequest == 1454 USB_DEVICE_B_HNP_ENABLE) 1455 udc->gadget.b_hnp_enable = 1; 1456 else if (setup->bRequest == 1457 USB_DEVICE_A_HNP_SUPPORT) 1458 udc->gadget.a_hnp_support = 1; 1459 else if (setup->bRequest == 1460 USB_DEVICE_A_ALT_HNP_SUPPORT) 1461 udc->gadget.a_alt_hnp_support = 1; 1462 } 1463 rc = 0; 1464 } else 1465 break; 1466 1467 if (rc == 0) { 1468 if (ep0_prime_status(udc, EP_DIR_IN)) 1469 ep0stall(udc); 1470 } 1471 if (ptc) { 1472 u32 tmp; 1473 1474 mdelay(10); 1475 tmp = fsl_readl(&dr_regs->portsc1) | (ptc << 16); 1476 fsl_writel(tmp, &dr_regs->portsc1); 1477 printk(KERN_INFO "udc: switch to test mode %d.\n", ptc); 1478 } 1479 1480 return; 1481 } 1482 1483 default: 1484 break; 1485 } 1486 1487 /* Requests handled by gadget */ 1488 if (wLength) { 1489 /* Data phase from gadget, status phase from udc */ 1490 udc->ep0_dir = (setup->bRequestType & USB_DIR_IN) 1491 ? USB_DIR_IN : USB_DIR_OUT; 1492 spin_unlock(&udc->lock); 1493 if (udc->driver->setup(&udc->gadget, 1494 &udc->local_setup_buff) < 0) 1495 ep0stall(udc); 1496 spin_lock(&udc->lock); 1497 udc->ep0_state = (setup->bRequestType & USB_DIR_IN) 1498 ? DATA_STATE_XMIT : DATA_STATE_RECV; 1499 /* 1500 * If the data stage is IN, send status prime immediately. 1501 * See 2.0 Spec chapter 8.5.3.3 for detail. 1502 */ 1503 if (udc->ep0_state == DATA_STATE_XMIT) 1504 if (ep0_prime_status(udc, EP_DIR_OUT)) 1505 ep0stall(udc); 1506 1507 } else { 1508 /* No data phase, IN status from gadget */ 1509 udc->ep0_dir = USB_DIR_IN; 1510 spin_unlock(&udc->lock); 1511 if (udc->driver->setup(&udc->gadget, 1512 &udc->local_setup_buff) < 0) 1513 ep0stall(udc); 1514 spin_lock(&udc->lock); 1515 udc->ep0_state = WAIT_FOR_OUT_STATUS; 1516 } 1517 } 1518 1519 /* Process request for Data or Status phase of ep0 1520 * prime status phase if needed */ 1521 static void ep0_req_complete(struct fsl_udc *udc, struct fsl_ep *ep0, 1522 struct fsl_req *req) 1523 { 1524 if (udc->usb_state == USB_STATE_ADDRESS) { 1525 /* Set the new address */ 1526 u32 new_address = (u32) udc->device_address; 1527 fsl_writel(new_address << USB_DEVICE_ADDRESS_BIT_POS, 1528 &dr_regs->deviceaddr); 1529 } 1530 1531 done(ep0, req, 0); 1532 1533 switch (udc->ep0_state) { 1534 case DATA_STATE_XMIT: 1535 /* already primed at setup_received_irq */ 1536 udc->ep0_state = WAIT_FOR_OUT_STATUS; 1537 break; 1538 case DATA_STATE_RECV: 1539 /* send status phase */ 1540 if (ep0_prime_status(udc, EP_DIR_IN)) 1541 ep0stall(udc); 1542 break; 1543 case WAIT_FOR_OUT_STATUS: 1544 udc->ep0_state = WAIT_FOR_SETUP; 1545 break; 1546 case WAIT_FOR_SETUP: 1547 ERR("Unexpected ep0 packets\n"); 1548 break; 1549 default: 1550 ep0stall(udc); 1551 break; 1552 } 1553 } 1554 1555 /* Tripwire mechanism to ensure a setup packet payload is extracted without 1556 * being corrupted by another incoming setup packet */ 1557 static void tripwire_handler(struct fsl_udc *udc, u8 ep_num, u8 *buffer_ptr) 1558 { 1559 u32 temp; 1560 struct ep_queue_head *qh; 1561 struct fsl_usb2_platform_data *pdata = udc->pdata; 1562 1563 qh = &udc->ep_qh[ep_num * 2 + EP_DIR_OUT]; 1564 1565 /* Clear bit in ENDPTSETUPSTAT */ 1566 temp = fsl_readl(&dr_regs->endptsetupstat); 1567 fsl_writel(temp | (1 << ep_num), &dr_regs->endptsetupstat); 1568 1569 /* while a hazard exists when setup package arrives */ 1570 do { 1571 /* Set Setup Tripwire */ 1572 temp = fsl_readl(&dr_regs->usbcmd); 1573 fsl_writel(temp | USB_CMD_SUTW, &dr_regs->usbcmd); 1574 1575 /* Copy the setup packet to local buffer */ 1576 if (pdata->le_setup_buf) { 1577 u32 *p = (u32 *)buffer_ptr; 1578 u32 *s = (u32 *)qh->setup_buffer; 1579 1580 /* Convert little endian setup buffer to CPU endian */ 1581 *p++ = le32_to_cpu(*s++); 1582 *p = le32_to_cpu(*s); 1583 } else { 1584 memcpy(buffer_ptr, (u8 *) qh->setup_buffer, 8); 1585 } 1586 } while (!(fsl_readl(&dr_regs->usbcmd) & USB_CMD_SUTW)); 1587 1588 /* Clear Setup Tripwire */ 1589 temp = fsl_readl(&dr_regs->usbcmd); 1590 fsl_writel(temp & ~USB_CMD_SUTW, &dr_regs->usbcmd); 1591 } 1592 1593 /* process-ep_req(): free the completed Tds for this req */ 1594 static int process_ep_req(struct fsl_udc *udc, int pipe, 1595 struct fsl_req *curr_req) 1596 { 1597 struct ep_td_struct *curr_td; 1598 int td_complete, actual, remaining_length, j, tmp; 1599 int status = 0; 1600 int errors = 0; 1601 struct ep_queue_head *curr_qh = &udc->ep_qh[pipe]; 1602 int direction = pipe % 2; 1603 1604 curr_td = curr_req->head; 1605 td_complete = 0; 1606 actual = curr_req->req.length; 1607 1608 for (j = 0; j < curr_req->dtd_count; j++) { 1609 remaining_length = (hc32_to_cpu(curr_td->size_ioc_sts) 1610 & DTD_PACKET_SIZE) 1611 >> DTD_LENGTH_BIT_POS; 1612 actual -= remaining_length; 1613 1614 errors = hc32_to_cpu(curr_td->size_ioc_sts); 1615 if (errors & DTD_ERROR_MASK) { 1616 if (errors & DTD_STATUS_HALTED) { 1617 ERR("dTD error %08x QH=%d\n", errors, pipe); 1618 /* Clear the errors and Halt condition */ 1619 tmp = hc32_to_cpu(curr_qh->size_ioc_int_sts); 1620 tmp &= ~errors; 1621 curr_qh->size_ioc_int_sts = cpu_to_hc32(tmp); 1622 status = -EPIPE; 1623 /* FIXME: continue with next queued TD? */ 1624 1625 break; 1626 } 1627 if (errors & DTD_STATUS_DATA_BUFF_ERR) { 1628 VDBG("Transfer overflow"); 1629 status = -EPROTO; 1630 break; 1631 } else if (errors & DTD_STATUS_TRANSACTION_ERR) { 1632 VDBG("ISO error"); 1633 status = -EILSEQ; 1634 break; 1635 } else 1636 ERR("Unknown error has occurred (0x%x)!\n", 1637 errors); 1638 1639 } else if (hc32_to_cpu(curr_td->size_ioc_sts) 1640 & DTD_STATUS_ACTIVE) { 1641 VDBG("Request not complete"); 1642 status = REQ_UNCOMPLETE; 1643 return status; 1644 } else if (remaining_length) { 1645 if (direction) { 1646 VDBG("Transmit dTD remaining length not zero"); 1647 status = -EPROTO; 1648 break; 1649 } else { 1650 td_complete++; 1651 break; 1652 } 1653 } else { 1654 td_complete++; 1655 VDBG("dTD transmitted successful"); 1656 } 1657 1658 if (j != curr_req->dtd_count - 1) 1659 curr_td = (struct ep_td_struct *)curr_td->next_td_virt; 1660 } 1661 1662 if (status) 1663 return status; 1664 1665 curr_req->req.actual = actual; 1666 1667 return 0; 1668 } 1669 1670 /* Process a DTD completion interrupt */ 1671 static void dtd_complete_irq(struct fsl_udc *udc) 1672 { 1673 u32 bit_pos; 1674 int i, ep_num, direction, bit_mask, status; 1675 struct fsl_ep *curr_ep; 1676 struct fsl_req *curr_req, *temp_req; 1677 1678 /* Clear the bits in the register */ 1679 bit_pos = fsl_readl(&dr_regs->endptcomplete); 1680 fsl_writel(bit_pos, &dr_regs->endptcomplete); 1681 1682 if (!bit_pos) 1683 return; 1684 1685 for (i = 0; i < udc->max_ep; i++) { 1686 ep_num = i >> 1; 1687 direction = i % 2; 1688 1689 bit_mask = 1 << (ep_num + 16 * direction); 1690 1691 if (!(bit_pos & bit_mask)) 1692 continue; 1693 1694 curr_ep = get_ep_by_pipe(udc, i); 1695 1696 /* If the ep is configured */ 1697 if (!curr_ep->ep.name) { 1698 WARNING("Invalid EP?"); 1699 continue; 1700 } 1701 1702 /* process the req queue until an uncomplete request */ 1703 list_for_each_entry_safe(curr_req, temp_req, &curr_ep->queue, 1704 queue) { 1705 status = process_ep_req(udc, i, curr_req); 1706 1707 VDBG("status of process_ep_req= %d, ep = %d", 1708 status, ep_num); 1709 if (status == REQ_UNCOMPLETE) 1710 break; 1711 /* write back status to req */ 1712 curr_req->req.status = status; 1713 1714 if (ep_num == 0) { 1715 ep0_req_complete(udc, curr_ep, curr_req); 1716 break; 1717 } else 1718 done(curr_ep, curr_req, status); 1719 } 1720 } 1721 } 1722 1723 static inline enum usb_device_speed portscx_device_speed(u32 reg) 1724 { 1725 switch (reg & PORTSCX_PORT_SPEED_MASK) { 1726 case PORTSCX_PORT_SPEED_HIGH: 1727 return USB_SPEED_HIGH; 1728 case PORTSCX_PORT_SPEED_FULL: 1729 return USB_SPEED_FULL; 1730 case PORTSCX_PORT_SPEED_LOW: 1731 return USB_SPEED_LOW; 1732 default: 1733 return USB_SPEED_UNKNOWN; 1734 } 1735 } 1736 1737 /* Process a port change interrupt */ 1738 static void port_change_irq(struct fsl_udc *udc) 1739 { 1740 if (udc->bus_reset) 1741 udc->bus_reset = 0; 1742 1743 /* Bus resetting is finished */ 1744 if (!(fsl_readl(&dr_regs->portsc1) & PORTSCX_PORT_RESET)) 1745 /* Get the speed */ 1746 udc->gadget.speed = 1747 portscx_device_speed(fsl_readl(&dr_regs->portsc1)); 1748 1749 /* Update USB state */ 1750 if (!udc->resume_state) 1751 udc->usb_state = USB_STATE_DEFAULT; 1752 } 1753 1754 /* Process suspend interrupt */ 1755 static void suspend_irq(struct fsl_udc *udc) 1756 { 1757 udc->resume_state = udc->usb_state; 1758 udc->usb_state = USB_STATE_SUSPENDED; 1759 1760 /* report suspend to the driver, serial.c does not support this */ 1761 if (udc->driver->suspend) 1762 udc->driver->suspend(&udc->gadget); 1763 } 1764 1765 static void bus_resume(struct fsl_udc *udc) 1766 { 1767 udc->usb_state = udc->resume_state; 1768 udc->resume_state = 0; 1769 1770 /* report resume to the driver, serial.c does not support this */ 1771 if (udc->driver->resume) 1772 udc->driver->resume(&udc->gadget); 1773 } 1774 1775 /* Clear up all ep queues */ 1776 static int reset_queues(struct fsl_udc *udc, bool bus_reset) 1777 { 1778 u8 pipe; 1779 1780 for (pipe = 0; pipe < udc->max_pipes; pipe++) 1781 udc_reset_ep_queue(udc, pipe); 1782 1783 /* report disconnect; the driver is already quiesced */ 1784 spin_unlock(&udc->lock); 1785 if (bus_reset) 1786 usb_gadget_udc_reset(&udc->gadget, udc->driver); 1787 else 1788 udc->driver->disconnect(&udc->gadget); 1789 spin_lock(&udc->lock); 1790 1791 return 0; 1792 } 1793 1794 /* Process reset interrupt */ 1795 static void reset_irq(struct fsl_udc *udc) 1796 { 1797 u32 temp; 1798 unsigned long timeout; 1799 1800 /* Clear the device address */ 1801 temp = fsl_readl(&dr_regs->deviceaddr); 1802 fsl_writel(temp & ~USB_DEVICE_ADDRESS_MASK, &dr_regs->deviceaddr); 1803 1804 udc->device_address = 0; 1805 1806 /* Clear usb state */ 1807 udc->resume_state = 0; 1808 udc->ep0_dir = 0; 1809 udc->ep0_state = WAIT_FOR_SETUP; 1810 udc->remote_wakeup = 0; /* default to 0 on reset */ 1811 udc->gadget.b_hnp_enable = 0; 1812 udc->gadget.a_hnp_support = 0; 1813 udc->gadget.a_alt_hnp_support = 0; 1814 1815 /* Clear all the setup token semaphores */ 1816 temp = fsl_readl(&dr_regs->endptsetupstat); 1817 fsl_writel(temp, &dr_regs->endptsetupstat); 1818 1819 /* Clear all the endpoint complete status bits */ 1820 temp = fsl_readl(&dr_regs->endptcomplete); 1821 fsl_writel(temp, &dr_regs->endptcomplete); 1822 1823 timeout = jiffies + 100; 1824 while (fsl_readl(&dr_regs->endpointprime)) { 1825 /* Wait until all endptprime bits cleared */ 1826 if (time_after(jiffies, timeout)) { 1827 ERR("Timeout for reset\n"); 1828 break; 1829 } 1830 cpu_relax(); 1831 } 1832 1833 /* Write 1s to the flush register */ 1834 fsl_writel(0xffffffff, &dr_regs->endptflush); 1835 1836 if (fsl_readl(&dr_regs->portsc1) & PORTSCX_PORT_RESET) { 1837 VDBG("Bus reset"); 1838 /* Bus is reseting */ 1839 udc->bus_reset = 1; 1840 /* Reset all the queues, include XD, dTD, EP queue 1841 * head and TR Queue */ 1842 reset_queues(udc, true); 1843 udc->usb_state = USB_STATE_DEFAULT; 1844 } else { 1845 VDBG("Controller reset"); 1846 /* initialize usb hw reg except for regs for EP, not 1847 * touch usbintr reg */ 1848 dr_controller_setup(udc); 1849 1850 /* Reset all internal used Queues */ 1851 reset_queues(udc, false); 1852 1853 ep0_setup(udc); 1854 1855 /* Enable DR IRQ reg, Set Run bit, change udc state */ 1856 dr_controller_run(udc); 1857 udc->usb_state = USB_STATE_ATTACHED; 1858 } 1859 } 1860 1861 /* 1862 * USB device controller interrupt handler 1863 */ 1864 static irqreturn_t fsl_udc_irq(int irq, void *_udc) 1865 { 1866 struct fsl_udc *udc = _udc; 1867 u32 irq_src; 1868 irqreturn_t status = IRQ_NONE; 1869 unsigned long flags; 1870 1871 /* Disable ISR for OTG host mode */ 1872 if (udc->stopped) 1873 return IRQ_NONE; 1874 spin_lock_irqsave(&udc->lock, flags); 1875 irq_src = fsl_readl(&dr_regs->usbsts) & fsl_readl(&dr_regs->usbintr); 1876 /* Clear notification bits */ 1877 fsl_writel(irq_src, &dr_regs->usbsts); 1878 1879 /* VDBG("irq_src [0x%8x]", irq_src); */ 1880 1881 /* Need to resume? */ 1882 if (udc->usb_state == USB_STATE_SUSPENDED) 1883 if ((fsl_readl(&dr_regs->portsc1) & PORTSCX_PORT_SUSPEND) == 0) 1884 bus_resume(udc); 1885 1886 /* USB Interrupt */ 1887 if (irq_src & USB_STS_INT) { 1888 VDBG("Packet int"); 1889 /* Setup package, we only support ep0 as control ep */ 1890 if (fsl_readl(&dr_regs->endptsetupstat) & EP_SETUP_STATUS_EP0) { 1891 tripwire_handler(udc, 0, 1892 (u8 *) (&udc->local_setup_buff)); 1893 setup_received_irq(udc, &udc->local_setup_buff); 1894 status = IRQ_HANDLED; 1895 } 1896 1897 /* completion of dtd */ 1898 if (fsl_readl(&dr_regs->endptcomplete)) { 1899 dtd_complete_irq(udc); 1900 status = IRQ_HANDLED; 1901 } 1902 } 1903 1904 /* SOF (for ISO transfer) */ 1905 if (irq_src & USB_STS_SOF) { 1906 status = IRQ_HANDLED; 1907 } 1908 1909 /* Port Change */ 1910 if (irq_src & USB_STS_PORT_CHANGE) { 1911 port_change_irq(udc); 1912 status = IRQ_HANDLED; 1913 } 1914 1915 /* Reset Received */ 1916 if (irq_src & USB_STS_RESET) { 1917 VDBG("reset int"); 1918 reset_irq(udc); 1919 status = IRQ_HANDLED; 1920 } 1921 1922 /* Sleep Enable (Suspend) */ 1923 if (irq_src & USB_STS_SUSPEND) { 1924 suspend_irq(udc); 1925 status = IRQ_HANDLED; 1926 } 1927 1928 if (irq_src & (USB_STS_ERR | USB_STS_SYS_ERR)) { 1929 VDBG("Error IRQ %x", irq_src); 1930 } 1931 1932 spin_unlock_irqrestore(&udc->lock, flags); 1933 return status; 1934 } 1935 1936 /*----------------------------------------------------------------* 1937 * Hook to gadget drivers 1938 * Called by initialization code of gadget drivers 1939 *----------------------------------------------------------------*/ 1940 static int fsl_udc_start(struct usb_gadget *g, 1941 struct usb_gadget_driver *driver) 1942 { 1943 int retval = 0; 1944 unsigned long flags = 0; 1945 1946 /* lock is needed but whether should use this lock or another */ 1947 spin_lock_irqsave(&udc_controller->lock, flags); 1948 1949 driver->driver.bus = NULL; 1950 /* hook up the driver */ 1951 udc_controller->driver = driver; 1952 spin_unlock_irqrestore(&udc_controller->lock, flags); 1953 g->is_selfpowered = 1; 1954 1955 if (!IS_ERR_OR_NULL(udc_controller->transceiver)) { 1956 /* Suspend the controller until OTG enable it */ 1957 udc_controller->stopped = 1; 1958 printk(KERN_INFO "Suspend udc for OTG auto detect\n"); 1959 1960 /* connect to bus through transceiver */ 1961 if (!IS_ERR_OR_NULL(udc_controller->transceiver)) { 1962 retval = otg_set_peripheral( 1963 udc_controller->transceiver->otg, 1964 &udc_controller->gadget); 1965 if (retval < 0) { 1966 ERR("can't bind to transceiver\n"); 1967 udc_controller->driver = NULL; 1968 return retval; 1969 } 1970 } 1971 } else { 1972 /* Enable DR IRQ reg and set USBCMD reg Run bit */ 1973 dr_controller_run(udc_controller); 1974 udc_controller->usb_state = USB_STATE_ATTACHED; 1975 udc_controller->ep0_state = WAIT_FOR_SETUP; 1976 udc_controller->ep0_dir = 0; 1977 } 1978 1979 return retval; 1980 } 1981 1982 /* Disconnect from gadget driver */ 1983 static int fsl_udc_stop(struct usb_gadget *g) 1984 { 1985 struct fsl_ep *loop_ep; 1986 unsigned long flags; 1987 1988 if (!IS_ERR_OR_NULL(udc_controller->transceiver)) 1989 otg_set_peripheral(udc_controller->transceiver->otg, NULL); 1990 1991 /* stop DR, disable intr */ 1992 dr_controller_stop(udc_controller); 1993 1994 /* in fact, no needed */ 1995 udc_controller->usb_state = USB_STATE_ATTACHED; 1996 udc_controller->ep0_state = WAIT_FOR_SETUP; 1997 udc_controller->ep0_dir = 0; 1998 1999 /* stand operation */ 2000 spin_lock_irqsave(&udc_controller->lock, flags); 2001 udc_controller->gadget.speed = USB_SPEED_UNKNOWN; 2002 nuke(&udc_controller->eps[0], -ESHUTDOWN); 2003 list_for_each_entry(loop_ep, &udc_controller->gadget.ep_list, 2004 ep.ep_list) 2005 nuke(loop_ep, -ESHUTDOWN); 2006 spin_unlock_irqrestore(&udc_controller->lock, flags); 2007 2008 udc_controller->driver = NULL; 2009 2010 return 0; 2011 } 2012 2013 /*------------------------------------------------------------------------- 2014 PROC File System Support 2015 -------------------------------------------------------------------------*/ 2016 #ifdef CONFIG_USB_GADGET_DEBUG_FILES 2017 2018 #include <linux/seq_file.h> 2019 2020 static const char proc_filename[] = "driver/fsl_usb2_udc"; 2021 2022 static int fsl_proc_read(struct seq_file *m, void *v) 2023 { 2024 unsigned long flags; 2025 int i; 2026 u32 tmp_reg; 2027 struct fsl_ep *ep = NULL; 2028 struct fsl_req *req; 2029 2030 struct fsl_udc *udc = udc_controller; 2031 2032 spin_lock_irqsave(&udc->lock, flags); 2033 2034 /* ------basic driver information ---- */ 2035 seq_printf(m, 2036 DRIVER_DESC "\n" 2037 "%s version: %s\n" 2038 "Gadget driver: %s\n\n", 2039 driver_name, DRIVER_VERSION, 2040 udc->driver ? udc->driver->driver.name : "(none)"); 2041 2042 /* ------ DR Registers ----- */ 2043 tmp_reg = fsl_readl(&dr_regs->usbcmd); 2044 seq_printf(m, 2045 "USBCMD reg:\n" 2046 "SetupTW: %d\n" 2047 "Run/Stop: %s\n\n", 2048 (tmp_reg & USB_CMD_SUTW) ? 1 : 0, 2049 (tmp_reg & USB_CMD_RUN_STOP) ? "Run" : "Stop"); 2050 2051 tmp_reg = fsl_readl(&dr_regs->usbsts); 2052 seq_printf(m, 2053 "USB Status Reg:\n" 2054 "Dr Suspend: %d Reset Received: %d System Error: %s " 2055 "USB Error Interrupt: %s\n\n", 2056 (tmp_reg & USB_STS_SUSPEND) ? 1 : 0, 2057 (tmp_reg & USB_STS_RESET) ? 1 : 0, 2058 (tmp_reg & USB_STS_SYS_ERR) ? "Err" : "Normal", 2059 (tmp_reg & USB_STS_ERR) ? "Err detected" : "No err"); 2060 2061 tmp_reg = fsl_readl(&dr_regs->usbintr); 2062 seq_printf(m, 2063 "USB Interrupt Enable Reg:\n" 2064 "Sleep Enable: %d SOF Received Enable: %d " 2065 "Reset Enable: %d\n" 2066 "System Error Enable: %d " 2067 "Port Change Dectected Enable: %d\n" 2068 "USB Error Intr Enable: %d USB Intr Enable: %d\n\n", 2069 (tmp_reg & USB_INTR_DEVICE_SUSPEND) ? 1 : 0, 2070 (tmp_reg & USB_INTR_SOF_EN) ? 1 : 0, 2071 (tmp_reg & USB_INTR_RESET_EN) ? 1 : 0, 2072 (tmp_reg & USB_INTR_SYS_ERR_EN) ? 1 : 0, 2073 (tmp_reg & USB_INTR_PTC_DETECT_EN) ? 1 : 0, 2074 (tmp_reg & USB_INTR_ERR_INT_EN) ? 1 : 0, 2075 (tmp_reg & USB_INTR_INT_EN) ? 1 : 0); 2076 2077 tmp_reg = fsl_readl(&dr_regs->frindex); 2078 seq_printf(m, 2079 "USB Frame Index Reg: Frame Number is 0x%x\n\n", 2080 (tmp_reg & USB_FRINDEX_MASKS)); 2081 2082 tmp_reg = fsl_readl(&dr_regs->deviceaddr); 2083 seq_printf(m, 2084 "USB Device Address Reg: Device Addr is 0x%x\n\n", 2085 (tmp_reg & USB_DEVICE_ADDRESS_MASK)); 2086 2087 tmp_reg = fsl_readl(&dr_regs->endpointlistaddr); 2088 seq_printf(m, 2089 "USB Endpoint List Address Reg: " 2090 "Device Addr is 0x%x\n\n", 2091 (tmp_reg & USB_EP_LIST_ADDRESS_MASK)); 2092 2093 tmp_reg = fsl_readl(&dr_regs->portsc1); 2094 seq_printf(m, 2095 "USB Port Status&Control Reg:\n" 2096 "Port Transceiver Type : %s Port Speed: %s\n" 2097 "PHY Low Power Suspend: %s Port Reset: %s " 2098 "Port Suspend Mode: %s\n" 2099 "Over-current Change: %s " 2100 "Port Enable/Disable Change: %s\n" 2101 "Port Enabled/Disabled: %s " 2102 "Current Connect Status: %s\n\n", ( { 2103 const char *s; 2104 switch (tmp_reg & PORTSCX_PTS_FSLS) { 2105 case PORTSCX_PTS_UTMI: 2106 s = "UTMI"; break; 2107 case PORTSCX_PTS_ULPI: 2108 s = "ULPI "; break; 2109 case PORTSCX_PTS_FSLS: 2110 s = "FS/LS Serial"; break; 2111 default: 2112 s = "None"; break; 2113 } 2114 s;} ), 2115 usb_speed_string(portscx_device_speed(tmp_reg)), 2116 (tmp_reg & PORTSCX_PHY_LOW_POWER_SPD) ? 2117 "Normal PHY mode" : "Low power mode", 2118 (tmp_reg & PORTSCX_PORT_RESET) ? "In Reset" : 2119 "Not in Reset", 2120 (tmp_reg & PORTSCX_PORT_SUSPEND) ? "In " : "Not in", 2121 (tmp_reg & PORTSCX_OVER_CURRENT_CHG) ? "Dected" : 2122 "No", 2123 (tmp_reg & PORTSCX_PORT_EN_DIS_CHANGE) ? "Disable" : 2124 "Not change", 2125 (tmp_reg & PORTSCX_PORT_ENABLE) ? "Enable" : 2126 "Not correct", 2127 (tmp_reg & PORTSCX_CURRENT_CONNECT_STATUS) ? 2128 "Attached" : "Not-Att"); 2129 2130 tmp_reg = fsl_readl(&dr_regs->usbmode); 2131 seq_printf(m, 2132 "USB Mode Reg: Controller Mode is: %s\n\n", ( { 2133 const char *s; 2134 switch (tmp_reg & USB_MODE_CTRL_MODE_HOST) { 2135 case USB_MODE_CTRL_MODE_IDLE: 2136 s = "Idle"; break; 2137 case USB_MODE_CTRL_MODE_DEVICE: 2138 s = "Device Controller"; break; 2139 case USB_MODE_CTRL_MODE_HOST: 2140 s = "Host Controller"; break; 2141 default: 2142 s = "None"; break; 2143 } 2144 s; 2145 } )); 2146 2147 tmp_reg = fsl_readl(&dr_regs->endptsetupstat); 2148 seq_printf(m, 2149 "Endpoint Setup Status Reg: SETUP on ep 0x%x\n\n", 2150 (tmp_reg & EP_SETUP_STATUS_MASK)); 2151 2152 for (i = 0; i < udc->max_ep / 2; i++) { 2153 tmp_reg = fsl_readl(&dr_regs->endptctrl[i]); 2154 seq_printf(m, "EP Ctrl Reg [0x%x]: = [0x%x]\n", i, tmp_reg); 2155 } 2156 tmp_reg = fsl_readl(&dr_regs->endpointprime); 2157 seq_printf(m, "EP Prime Reg = [0x%x]\n\n", tmp_reg); 2158 2159 #ifndef CONFIG_ARCH_MXC 2160 if (udc->pdata->have_sysif_regs) { 2161 tmp_reg = usb_sys_regs->snoop1; 2162 seq_printf(m, "Snoop1 Reg : = [0x%x]\n\n", tmp_reg); 2163 2164 tmp_reg = usb_sys_regs->control; 2165 seq_printf(m, "General Control Reg : = [0x%x]\n\n", tmp_reg); 2166 } 2167 #endif 2168 2169 /* ------fsl_udc, fsl_ep, fsl_request structure information ----- */ 2170 ep = &udc->eps[0]; 2171 seq_printf(m, "For %s Maxpkt is 0x%x index is 0x%x\n", 2172 ep->ep.name, ep_maxpacket(ep), ep_index(ep)); 2173 2174 if (list_empty(&ep->queue)) { 2175 seq_puts(m, "its req queue is empty\n\n"); 2176 } else { 2177 list_for_each_entry(req, &ep->queue, queue) { 2178 seq_printf(m, 2179 "req %p actual 0x%x length 0x%x buf %p\n", 2180 &req->req, req->req.actual, 2181 req->req.length, req->req.buf); 2182 } 2183 } 2184 /* other gadget->eplist ep */ 2185 list_for_each_entry(ep, &udc->gadget.ep_list, ep.ep_list) { 2186 if (ep->ep.desc) { 2187 seq_printf(m, 2188 "\nFor %s Maxpkt is 0x%x " 2189 "index is 0x%x\n", 2190 ep->ep.name, ep_maxpacket(ep), 2191 ep_index(ep)); 2192 2193 if (list_empty(&ep->queue)) { 2194 seq_puts(m, "its req queue is empty\n\n"); 2195 } else { 2196 list_for_each_entry(req, &ep->queue, queue) { 2197 seq_printf(m, 2198 "req %p actual 0x%x length " 2199 "0x%x buf %p\n", 2200 &req->req, req->req.actual, 2201 req->req.length, req->req.buf); 2202 } /* end for each_entry of ep req */ 2203 } /* end for else */ 2204 } /* end for if(ep->queue) */ 2205 } /* end (ep->desc) */ 2206 2207 spin_unlock_irqrestore(&udc->lock, flags); 2208 return 0; 2209 } 2210 2211 #define create_proc_file() \ 2212 proc_create_single(proc_filename, 0, NULL, fsl_proc_read) 2213 #define remove_proc_file() remove_proc_entry(proc_filename, NULL) 2214 2215 #else /* !CONFIG_USB_GADGET_DEBUG_FILES */ 2216 2217 #define create_proc_file() do {} while (0) 2218 #define remove_proc_file() do {} while (0) 2219 2220 #endif /* CONFIG_USB_GADGET_DEBUG_FILES */ 2221 2222 /*-------------------------------------------------------------------------*/ 2223 2224 /* Release udc structures */ 2225 static void fsl_udc_release(struct device *dev) 2226 { 2227 complete(udc_controller->done); 2228 dma_free_coherent(dev->parent, udc_controller->ep_qh_size, 2229 udc_controller->ep_qh, udc_controller->ep_qh_dma); 2230 kfree(udc_controller); 2231 } 2232 2233 /****************************************************************** 2234 Internal structure setup functions 2235 *******************************************************************/ 2236 /*------------------------------------------------------------------ 2237 * init resource for globle controller 2238 * Return the udc handle on success or NULL on failure 2239 ------------------------------------------------------------------*/ 2240 static int struct_udc_setup(struct fsl_udc *udc, 2241 struct platform_device *pdev) 2242 { 2243 struct fsl_usb2_platform_data *pdata; 2244 size_t size; 2245 2246 pdata = dev_get_platdata(&pdev->dev); 2247 udc->phy_mode = pdata->phy_mode; 2248 2249 udc->eps = kcalloc(udc->max_ep, sizeof(struct fsl_ep), GFP_KERNEL); 2250 if (!udc->eps) 2251 return -1; 2252 2253 /* initialized QHs, take care of alignment */ 2254 size = udc->max_ep * sizeof(struct ep_queue_head); 2255 if (size < QH_ALIGNMENT) 2256 size = QH_ALIGNMENT; 2257 else if ((size % QH_ALIGNMENT) != 0) { 2258 size += QH_ALIGNMENT + 1; 2259 size &= ~(QH_ALIGNMENT - 1); 2260 } 2261 udc->ep_qh = dma_alloc_coherent(&pdev->dev, size, 2262 &udc->ep_qh_dma, GFP_KERNEL); 2263 if (!udc->ep_qh) { 2264 ERR("malloc QHs for udc failed\n"); 2265 kfree(udc->eps); 2266 return -1; 2267 } 2268 2269 udc->ep_qh_size = size; 2270 2271 /* Initialize ep0 status request structure */ 2272 /* FIXME: fsl_alloc_request() ignores ep argument */ 2273 udc->status_req = container_of(fsl_alloc_request(NULL, GFP_KERNEL), 2274 struct fsl_req, req); 2275 /* allocate a small amount of memory to get valid address */ 2276 udc->status_req->req.buf = kmalloc(8, GFP_KERNEL); 2277 2278 udc->resume_state = USB_STATE_NOTATTACHED; 2279 udc->usb_state = USB_STATE_POWERED; 2280 udc->ep0_dir = 0; 2281 udc->remote_wakeup = 0; /* default to 0 on reset */ 2282 2283 return 0; 2284 } 2285 2286 /*---------------------------------------------------------------- 2287 * Setup the fsl_ep struct for eps 2288 * Link fsl_ep->ep to gadget->ep_list 2289 * ep0out is not used so do nothing here 2290 * ep0in should be taken care 2291 *--------------------------------------------------------------*/ 2292 static int struct_ep_setup(struct fsl_udc *udc, unsigned char index, 2293 char *name, int link) 2294 { 2295 struct fsl_ep *ep = &udc->eps[index]; 2296 2297 ep->udc = udc; 2298 strcpy(ep->name, name); 2299 ep->ep.name = ep->name; 2300 2301 ep->ep.ops = &fsl_ep_ops; 2302 ep->stopped = 0; 2303 2304 if (index == 0) { 2305 ep->ep.caps.type_control = true; 2306 } else { 2307 ep->ep.caps.type_iso = true; 2308 ep->ep.caps.type_bulk = true; 2309 ep->ep.caps.type_int = true; 2310 } 2311 2312 if (index & 1) 2313 ep->ep.caps.dir_in = true; 2314 else 2315 ep->ep.caps.dir_out = true; 2316 2317 /* for ep0: maxP defined in desc 2318 * for other eps, maxP is set by epautoconfig() called by gadget layer 2319 */ 2320 usb_ep_set_maxpacket_limit(&ep->ep, (unsigned short) ~0); 2321 2322 /* the queue lists any req for this ep */ 2323 INIT_LIST_HEAD(&ep->queue); 2324 2325 /* gagdet.ep_list used for ep_autoconfig so no ep0 */ 2326 if (link) 2327 list_add_tail(&ep->ep.ep_list, &udc->gadget.ep_list); 2328 ep->gadget = &udc->gadget; 2329 ep->qh = &udc->ep_qh[index]; 2330 2331 return 0; 2332 } 2333 2334 /* Driver probe function 2335 * all initialization operations implemented here except enabling usb_intr reg 2336 * board setup should have been done in the platform code 2337 */ 2338 static int fsl_udc_probe(struct platform_device *pdev) 2339 { 2340 struct fsl_usb2_platform_data *pdata; 2341 struct resource *res; 2342 int ret = -ENODEV; 2343 unsigned int i; 2344 u32 dccparams; 2345 2346 udc_controller = kzalloc(sizeof(struct fsl_udc), GFP_KERNEL); 2347 if (udc_controller == NULL) 2348 return -ENOMEM; 2349 2350 pdata = dev_get_platdata(&pdev->dev); 2351 udc_controller->pdata = pdata; 2352 spin_lock_init(&udc_controller->lock); 2353 udc_controller->stopped = 1; 2354 2355 #ifdef CONFIG_USB_OTG 2356 if (pdata->operating_mode == FSL_USB2_DR_OTG) { 2357 udc_controller->transceiver = usb_get_phy(USB_PHY_TYPE_USB2); 2358 if (IS_ERR_OR_NULL(udc_controller->transceiver)) { 2359 ERR("Can't find OTG driver!\n"); 2360 ret = -ENODEV; 2361 goto err_kfree; 2362 } 2363 } 2364 #endif 2365 2366 res = platform_get_resource(pdev, IORESOURCE_MEM, 0); 2367 if (!res) { 2368 ret = -ENXIO; 2369 goto err_kfree; 2370 } 2371 2372 if (pdata->operating_mode == FSL_USB2_DR_DEVICE) { 2373 if (!request_mem_region(res->start, resource_size(res), 2374 driver_name)) { 2375 ERR("request mem region for %s failed\n", pdev->name); 2376 ret = -EBUSY; 2377 goto err_kfree; 2378 } 2379 } 2380 2381 dr_regs = ioremap(res->start, resource_size(res)); 2382 if (!dr_regs) { 2383 ret = -ENOMEM; 2384 goto err_release_mem_region; 2385 } 2386 2387 pdata->regs = (void __iomem *)dr_regs; 2388 2389 /* 2390 * do platform specific init: check the clock, grab/config pins, etc. 2391 */ 2392 if (pdata->init && pdata->init(pdev)) { 2393 ret = -ENODEV; 2394 goto err_iounmap_noclk; 2395 } 2396 2397 /* Set accessors only after pdata->init() ! */ 2398 fsl_set_accessors(pdata); 2399 2400 #ifndef CONFIG_ARCH_MXC 2401 if (pdata->have_sysif_regs) 2402 usb_sys_regs = (void *)dr_regs + USB_DR_SYS_OFFSET; 2403 #endif 2404 2405 /* Initialize USB clocks */ 2406 ret = fsl_udc_clk_init(pdev); 2407 if (ret < 0) 2408 goto err_iounmap_noclk; 2409 2410 /* Read Device Controller Capability Parameters register */ 2411 dccparams = fsl_readl(&dr_regs->dccparams); 2412 if (!(dccparams & DCCPARAMS_DC)) { 2413 ERR("This SOC doesn't support device role\n"); 2414 ret = -ENODEV; 2415 goto err_iounmap; 2416 } 2417 /* Get max device endpoints */ 2418 /* DEN is bidirectional ep number, max_ep doubles the number */ 2419 udc_controller->max_ep = (dccparams & DCCPARAMS_DEN_MASK) * 2; 2420 2421 udc_controller->irq = platform_get_irq(pdev, 0); 2422 if (!udc_controller->irq) { 2423 ret = -ENODEV; 2424 goto err_iounmap; 2425 } 2426 2427 ret = request_irq(udc_controller->irq, fsl_udc_irq, IRQF_SHARED, 2428 driver_name, udc_controller); 2429 if (ret != 0) { 2430 ERR("cannot request irq %d err %d\n", 2431 udc_controller->irq, ret); 2432 goto err_iounmap; 2433 } 2434 2435 /* Initialize the udc structure including QH member and other member */ 2436 if (struct_udc_setup(udc_controller, pdev)) { 2437 ERR("Can't initialize udc data structure\n"); 2438 ret = -ENOMEM; 2439 goto err_free_irq; 2440 } 2441 2442 if (IS_ERR_OR_NULL(udc_controller->transceiver)) { 2443 /* initialize usb hw reg except for regs for EP, 2444 * leave usbintr reg untouched */ 2445 dr_controller_setup(udc_controller); 2446 } 2447 2448 ret = fsl_udc_clk_finalize(pdev); 2449 if (ret) 2450 goto err_free_irq; 2451 2452 /* Setup gadget structure */ 2453 udc_controller->gadget.ops = &fsl_gadget_ops; 2454 udc_controller->gadget.max_speed = USB_SPEED_HIGH; 2455 udc_controller->gadget.ep0 = &udc_controller->eps[0].ep; 2456 INIT_LIST_HEAD(&udc_controller->gadget.ep_list); 2457 udc_controller->gadget.speed = USB_SPEED_UNKNOWN; 2458 udc_controller->gadget.name = driver_name; 2459 2460 /* Setup gadget.dev and register with kernel */ 2461 dev_set_name(&udc_controller->gadget.dev, "gadget"); 2462 udc_controller->gadget.dev.of_node = pdev->dev.of_node; 2463 2464 if (!IS_ERR_OR_NULL(udc_controller->transceiver)) 2465 udc_controller->gadget.is_otg = 1; 2466 2467 /* setup QH and epctrl for ep0 */ 2468 ep0_setup(udc_controller); 2469 2470 /* setup udc->eps[] for ep0 */ 2471 struct_ep_setup(udc_controller, 0, "ep0", 0); 2472 /* for ep0: the desc defined here; 2473 * for other eps, gadget layer called ep_enable with defined desc 2474 */ 2475 udc_controller->eps[0].ep.desc = &fsl_ep0_desc; 2476 usb_ep_set_maxpacket_limit(&udc_controller->eps[0].ep, 2477 USB_MAX_CTRL_PAYLOAD); 2478 2479 /* setup the udc->eps[] for non-control endpoints and link 2480 * to gadget.ep_list */ 2481 for (i = 1; i < (int)(udc_controller->max_ep / 2); i++) { 2482 char name[14]; 2483 2484 sprintf(name, "ep%dout", i); 2485 struct_ep_setup(udc_controller, i * 2, name, 1); 2486 sprintf(name, "ep%din", i); 2487 struct_ep_setup(udc_controller, i * 2 + 1, name, 1); 2488 } 2489 2490 /* use dma_pool for TD management */ 2491 udc_controller->td_pool = dma_pool_create("udc_td", &pdev->dev, 2492 sizeof(struct ep_td_struct), 2493 DTD_ALIGNMENT, UDC_DMA_BOUNDARY); 2494 if (udc_controller->td_pool == NULL) { 2495 ret = -ENOMEM; 2496 goto err_free_irq; 2497 } 2498 2499 ret = usb_add_gadget_udc_release(&pdev->dev, &udc_controller->gadget, 2500 fsl_udc_release); 2501 if (ret) 2502 goto err_del_udc; 2503 2504 create_proc_file(); 2505 return 0; 2506 2507 err_del_udc: 2508 dma_pool_destroy(udc_controller->td_pool); 2509 err_free_irq: 2510 free_irq(udc_controller->irq, udc_controller); 2511 err_iounmap: 2512 if (pdata->exit) 2513 pdata->exit(pdev); 2514 fsl_udc_clk_release(); 2515 err_iounmap_noclk: 2516 iounmap(dr_regs); 2517 err_release_mem_region: 2518 if (pdata->operating_mode == FSL_USB2_DR_DEVICE) 2519 release_mem_region(res->start, resource_size(res)); 2520 err_kfree: 2521 kfree(udc_controller); 2522 udc_controller = NULL; 2523 return ret; 2524 } 2525 2526 /* Driver removal function 2527 * Free resources and finish pending transactions 2528 */ 2529 static int fsl_udc_remove(struct platform_device *pdev) 2530 { 2531 struct resource *res = platform_get_resource(pdev, IORESOURCE_MEM, 0); 2532 struct fsl_usb2_platform_data *pdata = dev_get_platdata(&pdev->dev); 2533 2534 DECLARE_COMPLETION_ONSTACK(done); 2535 2536 if (!udc_controller) 2537 return -ENODEV; 2538 2539 udc_controller->done = &done; 2540 usb_del_gadget_udc(&udc_controller->gadget); 2541 2542 fsl_udc_clk_release(); 2543 2544 /* DR has been stopped in usb_gadget_unregister_driver() */ 2545 remove_proc_file(); 2546 2547 /* Free allocated memory */ 2548 kfree(udc_controller->status_req->req.buf); 2549 kfree(udc_controller->status_req); 2550 kfree(udc_controller->eps); 2551 2552 dma_pool_destroy(udc_controller->td_pool); 2553 free_irq(udc_controller->irq, udc_controller); 2554 iounmap(dr_regs); 2555 if (pdata->operating_mode == FSL_USB2_DR_DEVICE) 2556 release_mem_region(res->start, resource_size(res)); 2557 2558 /* free udc --wait for the release() finished */ 2559 wait_for_completion(&done); 2560 2561 /* 2562 * do platform specific un-initialization: 2563 * release iomux pins, etc. 2564 */ 2565 if (pdata->exit) 2566 pdata->exit(pdev); 2567 2568 return 0; 2569 } 2570 2571 /*----------------------------------------------------------------- 2572 * Modify Power management attributes 2573 * Used by OTG statemachine to disable gadget temporarily 2574 -----------------------------------------------------------------*/ 2575 static int fsl_udc_suspend(struct platform_device *pdev, pm_message_t state) 2576 { 2577 dr_controller_stop(udc_controller); 2578 return 0; 2579 } 2580 2581 /*----------------------------------------------------------------- 2582 * Invoked on USB resume. May be called in_interrupt. 2583 * Here we start the DR controller and enable the irq 2584 *-----------------------------------------------------------------*/ 2585 static int fsl_udc_resume(struct platform_device *pdev) 2586 { 2587 /* Enable DR irq reg and set controller Run */ 2588 if (udc_controller->stopped) { 2589 dr_controller_setup(udc_controller); 2590 dr_controller_run(udc_controller); 2591 } 2592 udc_controller->usb_state = USB_STATE_ATTACHED; 2593 udc_controller->ep0_state = WAIT_FOR_SETUP; 2594 udc_controller->ep0_dir = 0; 2595 return 0; 2596 } 2597 2598 static int fsl_udc_otg_suspend(struct device *dev, pm_message_t state) 2599 { 2600 struct fsl_udc *udc = udc_controller; 2601 u32 mode, usbcmd; 2602 2603 mode = fsl_readl(&dr_regs->usbmode) & USB_MODE_CTRL_MODE_MASK; 2604 2605 pr_debug("%s(): mode 0x%x stopped %d\n", __func__, mode, udc->stopped); 2606 2607 /* 2608 * If the controller is already stopped, then this must be a 2609 * PM suspend. Remember this fact, so that we will leave the 2610 * controller stopped at PM resume time. 2611 */ 2612 if (udc->stopped) { 2613 pr_debug("gadget already stopped, leaving early\n"); 2614 udc->already_stopped = 1; 2615 return 0; 2616 } 2617 2618 if (mode != USB_MODE_CTRL_MODE_DEVICE) { 2619 pr_debug("gadget not in device mode, leaving early\n"); 2620 return 0; 2621 } 2622 2623 /* stop the controller */ 2624 usbcmd = fsl_readl(&dr_regs->usbcmd) & ~USB_CMD_RUN_STOP; 2625 fsl_writel(usbcmd, &dr_regs->usbcmd); 2626 2627 udc->stopped = 1; 2628 2629 pr_info("USB Gadget suspended\n"); 2630 2631 return 0; 2632 } 2633 2634 static int fsl_udc_otg_resume(struct device *dev) 2635 { 2636 pr_debug("%s(): stopped %d already_stopped %d\n", __func__, 2637 udc_controller->stopped, udc_controller->already_stopped); 2638 2639 /* 2640 * If the controller was stopped at suspend time, then 2641 * don't resume it now. 2642 */ 2643 if (udc_controller->already_stopped) { 2644 udc_controller->already_stopped = 0; 2645 pr_debug("gadget was already stopped, leaving early\n"); 2646 return 0; 2647 } 2648 2649 pr_info("USB Gadget resume\n"); 2650 2651 return fsl_udc_resume(NULL); 2652 } 2653 /*------------------------------------------------------------------------- 2654 Register entry point for the peripheral controller driver 2655 --------------------------------------------------------------------------*/ 2656 static const struct platform_device_id fsl_udc_devtype[] = { 2657 { 2658 .name = "imx-udc-mx27", 2659 }, { 2660 .name = "imx-udc-mx51", 2661 }, { 2662 .name = "fsl-usb2-udc", 2663 }, { 2664 /* sentinel */ 2665 } 2666 }; 2667 MODULE_DEVICE_TABLE(platform, fsl_udc_devtype); 2668 static struct platform_driver udc_driver = { 2669 .remove = fsl_udc_remove, 2670 /* Just for FSL i.mx SoC currently */ 2671 .id_table = fsl_udc_devtype, 2672 /* these suspend and resume are not usb suspend and resume */ 2673 .suspend = fsl_udc_suspend, 2674 .resume = fsl_udc_resume, 2675 .driver = { 2676 .name = driver_name, 2677 /* udc suspend/resume called from OTG driver */ 2678 .suspend = fsl_udc_otg_suspend, 2679 .resume = fsl_udc_otg_resume, 2680 }, 2681 }; 2682 2683 module_platform_driver_probe(udc_driver, fsl_udc_probe); 2684 2685 MODULE_DESCRIPTION(DRIVER_DESC); 2686 MODULE_AUTHOR(DRIVER_AUTHOR); 2687 MODULE_LICENSE("GPL"); 2688 MODULE_ALIAS("platform:fsl-usb2-udc"); 2689