1 // SPDX-License-Identifier: GPL-2.0 2 /* 3 * Driver for the Atmel USBA high speed USB device controller 4 * 5 * Copyright (C) 2005-2007 Atmel Corporation 6 */ 7 #include <linux/clk.h> 8 #include <linux/clk/at91_pmc.h> 9 #include <linux/module.h> 10 #include <linux/init.h> 11 #include <linux/interrupt.h> 12 #include <linux/io.h> 13 #include <linux/slab.h> 14 #include <linux/device.h> 15 #include <linux/dma-mapping.h> 16 #include <linux/list.h> 17 #include <linux/mfd/syscon.h> 18 #include <linux/platform_device.h> 19 #include <linux/regmap.h> 20 #include <linux/ctype.h> 21 #include <linux/usb.h> 22 #include <linux/usb/ch9.h> 23 #include <linux/usb/gadget.h> 24 #include <linux/delay.h> 25 #include <linux/of.h> 26 #include <linux/irq.h> 27 #include <linux/gpio/consumer.h> 28 29 #include "atmel_usba_udc.h" 30 #define USBA_VBUS_IRQFLAGS (IRQF_ONESHOT \ 31 | IRQF_TRIGGER_FALLING | IRQF_TRIGGER_RISING) 32 33 #ifdef CONFIG_USB_GADGET_DEBUG_FS 34 #include <linux/debugfs.h> 35 #include <linux/uaccess.h> 36 37 static int queue_dbg_open(struct inode *inode, struct file *file) 38 { 39 struct usba_ep *ep = inode->i_private; 40 struct usba_request *req, *req_copy; 41 struct list_head *queue_data; 42 43 queue_data = kmalloc(sizeof(*queue_data), GFP_KERNEL); 44 if (!queue_data) 45 return -ENOMEM; 46 INIT_LIST_HEAD(queue_data); 47 48 spin_lock_irq(&ep->udc->lock); 49 list_for_each_entry(req, &ep->queue, queue) { 50 req_copy = kmemdup(req, sizeof(*req_copy), GFP_ATOMIC); 51 if (!req_copy) 52 goto fail; 53 list_add_tail(&req_copy->queue, queue_data); 54 } 55 spin_unlock_irq(&ep->udc->lock); 56 57 file->private_data = queue_data; 58 return 0; 59 60 fail: 61 spin_unlock_irq(&ep->udc->lock); 62 list_for_each_entry_safe(req, req_copy, queue_data, queue) { 63 list_del(&req->queue); 64 kfree(req); 65 } 66 kfree(queue_data); 67 return -ENOMEM; 68 } 69 70 /* 71 * bbbbbbbb llllllll IZS sssss nnnn FDL\n\0 72 * 73 * b: buffer address 74 * l: buffer length 75 * I/i: interrupt/no interrupt 76 * Z/z: zero/no zero 77 * S/s: short ok/short not ok 78 * s: status 79 * n: nr_packets 80 * F/f: submitted/not submitted to FIFO 81 * D/d: using/not using DMA 82 * L/l: last transaction/not last transaction 83 */ 84 static ssize_t queue_dbg_read(struct file *file, char __user *buf, 85 size_t nbytes, loff_t *ppos) 86 { 87 struct list_head *queue = file->private_data; 88 struct usba_request *req, *tmp_req; 89 size_t len, remaining, actual = 0; 90 char tmpbuf[38]; 91 92 if (!access_ok(buf, nbytes)) 93 return -EFAULT; 94 95 inode_lock(file_inode(file)); 96 list_for_each_entry_safe(req, tmp_req, queue, queue) { 97 len = snprintf(tmpbuf, sizeof(tmpbuf), 98 "%8p %08x %c%c%c %5d %c%c%c\n", 99 req->req.buf, req->req.length, 100 req->req.no_interrupt ? 'i' : 'I', 101 req->req.zero ? 'Z' : 'z', 102 req->req.short_not_ok ? 's' : 'S', 103 req->req.status, 104 req->submitted ? 'F' : 'f', 105 req->using_dma ? 'D' : 'd', 106 req->last_transaction ? 'L' : 'l'); 107 len = min(len, sizeof(tmpbuf)); 108 if (len > nbytes) 109 break; 110 111 list_del(&req->queue); 112 kfree(req); 113 114 remaining = __copy_to_user(buf, tmpbuf, len); 115 actual += len - remaining; 116 if (remaining) 117 break; 118 119 nbytes -= len; 120 buf += len; 121 } 122 inode_unlock(file_inode(file)); 123 124 return actual; 125 } 126 127 static int queue_dbg_release(struct inode *inode, struct file *file) 128 { 129 struct list_head *queue_data = file->private_data; 130 struct usba_request *req, *tmp_req; 131 132 list_for_each_entry_safe(req, tmp_req, queue_data, queue) { 133 list_del(&req->queue); 134 kfree(req); 135 } 136 kfree(queue_data); 137 return 0; 138 } 139 140 static int regs_dbg_open(struct inode *inode, struct file *file) 141 { 142 struct usba_udc *udc; 143 unsigned int i; 144 u32 *data; 145 int ret = -ENOMEM; 146 147 inode_lock(inode); 148 udc = inode->i_private; 149 data = kmalloc(inode->i_size, GFP_KERNEL); 150 if (!data) 151 goto out; 152 153 spin_lock_irq(&udc->lock); 154 for (i = 0; i < inode->i_size / 4; i++) 155 data[i] = readl_relaxed(udc->regs + i * 4); 156 spin_unlock_irq(&udc->lock); 157 158 file->private_data = data; 159 ret = 0; 160 161 out: 162 inode_unlock(inode); 163 164 return ret; 165 } 166 167 static ssize_t regs_dbg_read(struct file *file, char __user *buf, 168 size_t nbytes, loff_t *ppos) 169 { 170 struct inode *inode = file_inode(file); 171 int ret; 172 173 inode_lock(inode); 174 ret = simple_read_from_buffer(buf, nbytes, ppos, 175 file->private_data, 176 file_inode(file)->i_size); 177 inode_unlock(inode); 178 179 return ret; 180 } 181 182 static int regs_dbg_release(struct inode *inode, struct file *file) 183 { 184 kfree(file->private_data); 185 return 0; 186 } 187 188 const struct file_operations queue_dbg_fops = { 189 .owner = THIS_MODULE, 190 .open = queue_dbg_open, 191 .llseek = no_llseek, 192 .read = queue_dbg_read, 193 .release = queue_dbg_release, 194 }; 195 196 const struct file_operations regs_dbg_fops = { 197 .owner = THIS_MODULE, 198 .open = regs_dbg_open, 199 .llseek = generic_file_llseek, 200 .read = regs_dbg_read, 201 .release = regs_dbg_release, 202 }; 203 204 static void usba_ep_init_debugfs(struct usba_udc *udc, 205 struct usba_ep *ep) 206 { 207 struct dentry *ep_root; 208 209 ep_root = debugfs_create_dir(ep->ep.name, udc->debugfs_root); 210 ep->debugfs_dir = ep_root; 211 212 debugfs_create_file("queue", 0400, ep_root, ep, &queue_dbg_fops); 213 if (ep->can_dma) 214 debugfs_create_u32("dma_status", 0400, ep_root, 215 &ep->last_dma_status); 216 if (ep_is_control(ep)) 217 debugfs_create_u32("state", 0400, ep_root, &ep->state); 218 } 219 220 static void usba_ep_cleanup_debugfs(struct usba_ep *ep) 221 { 222 debugfs_remove_recursive(ep->debugfs_dir); 223 } 224 225 static void usba_init_debugfs(struct usba_udc *udc) 226 { 227 struct dentry *root; 228 struct resource *regs_resource; 229 230 root = debugfs_create_dir(udc->gadget.name, usb_debug_root); 231 udc->debugfs_root = root; 232 233 regs_resource = platform_get_resource(udc->pdev, IORESOURCE_MEM, 234 CTRL_IOMEM_ID); 235 236 if (regs_resource) { 237 debugfs_create_file_size("regs", 0400, root, udc, 238 ®s_dbg_fops, 239 resource_size(regs_resource)); 240 } 241 242 usba_ep_init_debugfs(udc, to_usba_ep(udc->gadget.ep0)); 243 } 244 245 static void usba_cleanup_debugfs(struct usba_udc *udc) 246 { 247 usba_ep_cleanup_debugfs(to_usba_ep(udc->gadget.ep0)); 248 debugfs_remove_recursive(udc->debugfs_root); 249 } 250 #else 251 static inline void usba_ep_init_debugfs(struct usba_udc *udc, 252 struct usba_ep *ep) 253 { 254 255 } 256 257 static inline void usba_ep_cleanup_debugfs(struct usba_ep *ep) 258 { 259 260 } 261 262 static inline void usba_init_debugfs(struct usba_udc *udc) 263 { 264 265 } 266 267 static inline void usba_cleanup_debugfs(struct usba_udc *udc) 268 { 269 270 } 271 #endif 272 273 static ushort fifo_mode; 274 275 module_param(fifo_mode, ushort, 0x0); 276 MODULE_PARM_DESC(fifo_mode, "Endpoint configuration mode"); 277 278 /* mode 0 - uses autoconfig */ 279 280 /* mode 1 - fits in 8KB, generic max fifo configuration */ 281 static struct usba_fifo_cfg mode_1_cfg[] = { 282 { .hw_ep_num = 0, .fifo_size = 64, .nr_banks = 1, }, 283 { .hw_ep_num = 1, .fifo_size = 1024, .nr_banks = 2, }, 284 { .hw_ep_num = 2, .fifo_size = 1024, .nr_banks = 1, }, 285 { .hw_ep_num = 3, .fifo_size = 1024, .nr_banks = 1, }, 286 { .hw_ep_num = 4, .fifo_size = 1024, .nr_banks = 1, }, 287 { .hw_ep_num = 5, .fifo_size = 1024, .nr_banks = 1, }, 288 { .hw_ep_num = 6, .fifo_size = 1024, .nr_banks = 1, }, 289 }; 290 291 /* mode 2 - fits in 8KB, performance max fifo configuration */ 292 static struct usba_fifo_cfg mode_2_cfg[] = { 293 { .hw_ep_num = 0, .fifo_size = 64, .nr_banks = 1, }, 294 { .hw_ep_num = 1, .fifo_size = 1024, .nr_banks = 3, }, 295 { .hw_ep_num = 2, .fifo_size = 1024, .nr_banks = 2, }, 296 { .hw_ep_num = 3, .fifo_size = 1024, .nr_banks = 2, }, 297 }; 298 299 /* mode 3 - fits in 8KB, mixed fifo configuration */ 300 static struct usba_fifo_cfg mode_3_cfg[] = { 301 { .hw_ep_num = 0, .fifo_size = 64, .nr_banks = 1, }, 302 { .hw_ep_num = 1, .fifo_size = 1024, .nr_banks = 2, }, 303 { .hw_ep_num = 2, .fifo_size = 512, .nr_banks = 2, }, 304 { .hw_ep_num = 3, .fifo_size = 512, .nr_banks = 2, }, 305 { .hw_ep_num = 4, .fifo_size = 512, .nr_banks = 2, }, 306 { .hw_ep_num = 5, .fifo_size = 512, .nr_banks = 2, }, 307 { .hw_ep_num = 6, .fifo_size = 512, .nr_banks = 2, }, 308 }; 309 310 /* mode 4 - fits in 8KB, custom fifo configuration */ 311 static struct usba_fifo_cfg mode_4_cfg[] = { 312 { .hw_ep_num = 0, .fifo_size = 64, .nr_banks = 1, }, 313 { .hw_ep_num = 1, .fifo_size = 512, .nr_banks = 2, }, 314 { .hw_ep_num = 2, .fifo_size = 512, .nr_banks = 2, }, 315 { .hw_ep_num = 3, .fifo_size = 8, .nr_banks = 2, }, 316 { .hw_ep_num = 4, .fifo_size = 512, .nr_banks = 2, }, 317 { .hw_ep_num = 5, .fifo_size = 512, .nr_banks = 2, }, 318 { .hw_ep_num = 6, .fifo_size = 16, .nr_banks = 2, }, 319 { .hw_ep_num = 7, .fifo_size = 8, .nr_banks = 2, }, 320 { .hw_ep_num = 8, .fifo_size = 8, .nr_banks = 2, }, 321 }; 322 /* Add additional configurations here */ 323 324 static int usba_config_fifo_table(struct usba_udc *udc) 325 { 326 int n; 327 328 switch (fifo_mode) { 329 default: 330 fifo_mode = 0; 331 /* fall through */ 332 case 0: 333 udc->fifo_cfg = NULL; 334 n = 0; 335 break; 336 case 1: 337 udc->fifo_cfg = mode_1_cfg; 338 n = ARRAY_SIZE(mode_1_cfg); 339 break; 340 case 2: 341 udc->fifo_cfg = mode_2_cfg; 342 n = ARRAY_SIZE(mode_2_cfg); 343 break; 344 case 3: 345 udc->fifo_cfg = mode_3_cfg; 346 n = ARRAY_SIZE(mode_3_cfg); 347 break; 348 case 4: 349 udc->fifo_cfg = mode_4_cfg; 350 n = ARRAY_SIZE(mode_4_cfg); 351 break; 352 } 353 DBG(DBG_HW, "Setup fifo_mode %d\n", fifo_mode); 354 355 return n; 356 } 357 358 static inline u32 usba_int_enb_get(struct usba_udc *udc) 359 { 360 return udc->int_enb_cache; 361 } 362 363 static inline void usba_int_enb_set(struct usba_udc *udc, u32 mask) 364 { 365 u32 val; 366 367 val = udc->int_enb_cache | mask; 368 usba_writel(udc, INT_ENB, val); 369 udc->int_enb_cache = val; 370 } 371 372 static inline void usba_int_enb_clear(struct usba_udc *udc, u32 mask) 373 { 374 u32 val; 375 376 val = udc->int_enb_cache & ~mask; 377 usba_writel(udc, INT_ENB, val); 378 udc->int_enb_cache = val; 379 } 380 381 static int vbus_is_present(struct usba_udc *udc) 382 { 383 if (udc->vbus_pin) 384 return gpiod_get_value(udc->vbus_pin); 385 386 /* No Vbus detection: Assume always present */ 387 return 1; 388 } 389 390 static void toggle_bias(struct usba_udc *udc, int is_on) 391 { 392 if (udc->errata && udc->errata->toggle_bias) 393 udc->errata->toggle_bias(udc, is_on); 394 } 395 396 static void generate_bias_pulse(struct usba_udc *udc) 397 { 398 if (!udc->bias_pulse_needed) 399 return; 400 401 if (udc->errata && udc->errata->pulse_bias) 402 udc->errata->pulse_bias(udc); 403 404 udc->bias_pulse_needed = false; 405 } 406 407 static void next_fifo_transaction(struct usba_ep *ep, struct usba_request *req) 408 { 409 unsigned int transaction_len; 410 411 transaction_len = req->req.length - req->req.actual; 412 req->last_transaction = 1; 413 if (transaction_len > ep->ep.maxpacket) { 414 transaction_len = ep->ep.maxpacket; 415 req->last_transaction = 0; 416 } else if (transaction_len == ep->ep.maxpacket && req->req.zero) 417 req->last_transaction = 0; 418 419 DBG(DBG_QUEUE, "%s: submit_transaction, req %p (length %d)%s\n", 420 ep->ep.name, req, transaction_len, 421 req->last_transaction ? ", done" : ""); 422 423 memcpy_toio(ep->fifo, req->req.buf + req->req.actual, transaction_len); 424 usba_ep_writel(ep, SET_STA, USBA_TX_PK_RDY); 425 req->req.actual += transaction_len; 426 } 427 428 static void submit_request(struct usba_ep *ep, struct usba_request *req) 429 { 430 DBG(DBG_QUEUE, "%s: submit_request: req %p (length %d)\n", 431 ep->ep.name, req, req->req.length); 432 433 req->req.actual = 0; 434 req->submitted = 1; 435 436 if (req->using_dma) { 437 if (req->req.length == 0) { 438 usba_ep_writel(ep, CTL_ENB, USBA_TX_PK_RDY); 439 return; 440 } 441 442 if (req->req.zero) 443 usba_ep_writel(ep, CTL_ENB, USBA_SHORT_PACKET); 444 else 445 usba_ep_writel(ep, CTL_DIS, USBA_SHORT_PACKET); 446 447 usba_dma_writel(ep, ADDRESS, req->req.dma); 448 usba_dma_writel(ep, CONTROL, req->ctrl); 449 } else { 450 next_fifo_transaction(ep, req); 451 if (req->last_transaction) { 452 usba_ep_writel(ep, CTL_DIS, USBA_TX_PK_RDY); 453 if (ep_is_control(ep)) 454 usba_ep_writel(ep, CTL_ENB, USBA_TX_COMPLETE); 455 } else { 456 if (ep_is_control(ep)) 457 usba_ep_writel(ep, CTL_DIS, USBA_TX_COMPLETE); 458 usba_ep_writel(ep, CTL_ENB, USBA_TX_PK_RDY); 459 } 460 } 461 } 462 463 static void submit_next_request(struct usba_ep *ep) 464 { 465 struct usba_request *req; 466 467 if (list_empty(&ep->queue)) { 468 usba_ep_writel(ep, CTL_DIS, USBA_TX_PK_RDY | USBA_RX_BK_RDY); 469 return; 470 } 471 472 req = list_entry(ep->queue.next, struct usba_request, queue); 473 if (!req->submitted) 474 submit_request(ep, req); 475 } 476 477 static void send_status(struct usba_udc *udc, struct usba_ep *ep) 478 { 479 ep->state = STATUS_STAGE_IN; 480 usba_ep_writel(ep, SET_STA, USBA_TX_PK_RDY); 481 usba_ep_writel(ep, CTL_ENB, USBA_TX_COMPLETE); 482 } 483 484 static void receive_data(struct usba_ep *ep) 485 { 486 struct usba_udc *udc = ep->udc; 487 struct usba_request *req; 488 unsigned long status; 489 unsigned int bytecount, nr_busy; 490 int is_complete = 0; 491 492 status = usba_ep_readl(ep, STA); 493 nr_busy = USBA_BFEXT(BUSY_BANKS, status); 494 495 DBG(DBG_QUEUE, "receive data: nr_busy=%u\n", nr_busy); 496 497 while (nr_busy > 0) { 498 if (list_empty(&ep->queue)) { 499 usba_ep_writel(ep, CTL_DIS, USBA_RX_BK_RDY); 500 break; 501 } 502 req = list_entry(ep->queue.next, 503 struct usba_request, queue); 504 505 bytecount = USBA_BFEXT(BYTE_COUNT, status); 506 507 if (status & (1 << 31)) 508 is_complete = 1; 509 if (req->req.actual + bytecount >= req->req.length) { 510 is_complete = 1; 511 bytecount = req->req.length - req->req.actual; 512 } 513 514 memcpy_fromio(req->req.buf + req->req.actual, 515 ep->fifo, bytecount); 516 req->req.actual += bytecount; 517 518 usba_ep_writel(ep, CLR_STA, USBA_RX_BK_RDY); 519 520 if (is_complete) { 521 DBG(DBG_QUEUE, "%s: request done\n", ep->ep.name); 522 req->req.status = 0; 523 list_del_init(&req->queue); 524 usba_ep_writel(ep, CTL_DIS, USBA_RX_BK_RDY); 525 spin_unlock(&udc->lock); 526 usb_gadget_giveback_request(&ep->ep, &req->req); 527 spin_lock(&udc->lock); 528 } 529 530 status = usba_ep_readl(ep, STA); 531 nr_busy = USBA_BFEXT(BUSY_BANKS, status); 532 533 if (is_complete && ep_is_control(ep)) { 534 send_status(udc, ep); 535 break; 536 } 537 } 538 } 539 540 static void 541 request_complete(struct usba_ep *ep, struct usba_request *req, int status) 542 { 543 struct usba_udc *udc = ep->udc; 544 545 WARN_ON(!list_empty(&req->queue)); 546 547 if (req->req.status == -EINPROGRESS) 548 req->req.status = status; 549 550 if (req->using_dma) 551 usb_gadget_unmap_request(&udc->gadget, &req->req, ep->is_in); 552 553 DBG(DBG_GADGET | DBG_REQ, 554 "%s: req %p complete: status %d, actual %u\n", 555 ep->ep.name, req, req->req.status, req->req.actual); 556 557 spin_unlock(&udc->lock); 558 usb_gadget_giveback_request(&ep->ep, &req->req); 559 spin_lock(&udc->lock); 560 } 561 562 static void 563 request_complete_list(struct usba_ep *ep, struct list_head *list, int status) 564 { 565 struct usba_request *req, *tmp_req; 566 567 list_for_each_entry_safe(req, tmp_req, list, queue) { 568 list_del_init(&req->queue); 569 request_complete(ep, req, status); 570 } 571 } 572 573 static int 574 usba_ep_enable(struct usb_ep *_ep, const struct usb_endpoint_descriptor *desc) 575 { 576 struct usba_ep *ep = to_usba_ep(_ep); 577 struct usba_udc *udc = ep->udc; 578 unsigned long flags, maxpacket; 579 unsigned int nr_trans; 580 581 DBG(DBG_GADGET, "%s: ep_enable: desc=%p\n", ep->ep.name, desc); 582 583 maxpacket = usb_endpoint_maxp(desc); 584 585 if (((desc->bEndpointAddress & USB_ENDPOINT_NUMBER_MASK) != ep->index) 586 || ep->index == 0 587 || desc->bDescriptorType != USB_DT_ENDPOINT 588 || maxpacket == 0 589 || maxpacket > ep->fifo_size) { 590 DBG(DBG_ERR, "ep_enable: Invalid argument"); 591 return -EINVAL; 592 } 593 594 ep->is_isoc = 0; 595 ep->is_in = 0; 596 597 DBG(DBG_ERR, "%s: EPT_CFG = 0x%lx (maxpacket = %lu)\n", 598 ep->ep.name, ep->ept_cfg, maxpacket); 599 600 if (usb_endpoint_dir_in(desc)) { 601 ep->is_in = 1; 602 ep->ept_cfg |= USBA_EPT_DIR_IN; 603 } 604 605 switch (usb_endpoint_type(desc)) { 606 case USB_ENDPOINT_XFER_CONTROL: 607 ep->ept_cfg |= USBA_BF(EPT_TYPE, USBA_EPT_TYPE_CONTROL); 608 break; 609 case USB_ENDPOINT_XFER_ISOC: 610 if (!ep->can_isoc) { 611 DBG(DBG_ERR, "ep_enable: %s is not isoc capable\n", 612 ep->ep.name); 613 return -EINVAL; 614 } 615 616 /* 617 * Bits 11:12 specify number of _additional_ 618 * transactions per microframe. 619 */ 620 nr_trans = usb_endpoint_maxp_mult(desc); 621 if (nr_trans > 3) 622 return -EINVAL; 623 624 ep->is_isoc = 1; 625 ep->ept_cfg |= USBA_BF(EPT_TYPE, USBA_EPT_TYPE_ISO); 626 ep->ept_cfg |= USBA_BF(NB_TRANS, nr_trans); 627 628 break; 629 case USB_ENDPOINT_XFER_BULK: 630 ep->ept_cfg |= USBA_BF(EPT_TYPE, USBA_EPT_TYPE_BULK); 631 break; 632 case USB_ENDPOINT_XFER_INT: 633 ep->ept_cfg |= USBA_BF(EPT_TYPE, USBA_EPT_TYPE_INT); 634 break; 635 } 636 637 spin_lock_irqsave(&ep->udc->lock, flags); 638 639 ep->ep.desc = desc; 640 ep->ep.maxpacket = maxpacket; 641 642 usba_ep_writel(ep, CFG, ep->ept_cfg); 643 usba_ep_writel(ep, CTL_ENB, USBA_EPT_ENABLE); 644 645 if (ep->can_dma) { 646 u32 ctrl; 647 648 usba_int_enb_set(udc, USBA_BF(EPT_INT, 1 << ep->index) | 649 USBA_BF(DMA_INT, 1 << ep->index)); 650 ctrl = USBA_AUTO_VALID | USBA_INTDIS_DMA; 651 usba_ep_writel(ep, CTL_ENB, ctrl); 652 } else { 653 usba_int_enb_set(udc, USBA_BF(EPT_INT, 1 << ep->index)); 654 } 655 656 spin_unlock_irqrestore(&udc->lock, flags); 657 658 DBG(DBG_HW, "EPT_CFG%d after init: %#08lx\n", ep->index, 659 (unsigned long)usba_ep_readl(ep, CFG)); 660 DBG(DBG_HW, "INT_ENB after init: %#08lx\n", 661 (unsigned long)usba_int_enb_get(udc)); 662 663 return 0; 664 } 665 666 static int usba_ep_disable(struct usb_ep *_ep) 667 { 668 struct usba_ep *ep = to_usba_ep(_ep); 669 struct usba_udc *udc = ep->udc; 670 LIST_HEAD(req_list); 671 unsigned long flags; 672 673 DBG(DBG_GADGET, "ep_disable: %s\n", ep->ep.name); 674 675 spin_lock_irqsave(&udc->lock, flags); 676 677 if (!ep->ep.desc) { 678 spin_unlock_irqrestore(&udc->lock, flags); 679 /* REVISIT because this driver disables endpoints in 680 * reset_all_endpoints() before calling disconnect(), 681 * most gadget drivers would trigger this non-error ... 682 */ 683 if (udc->gadget.speed != USB_SPEED_UNKNOWN) 684 DBG(DBG_ERR, "ep_disable: %s not enabled\n", 685 ep->ep.name); 686 return -EINVAL; 687 } 688 ep->ep.desc = NULL; 689 690 list_splice_init(&ep->queue, &req_list); 691 if (ep->can_dma) { 692 usba_dma_writel(ep, CONTROL, 0); 693 usba_dma_writel(ep, ADDRESS, 0); 694 usba_dma_readl(ep, STATUS); 695 } 696 usba_ep_writel(ep, CTL_DIS, USBA_EPT_ENABLE); 697 usba_int_enb_clear(udc, USBA_BF(EPT_INT, 1 << ep->index)); 698 699 request_complete_list(ep, &req_list, -ESHUTDOWN); 700 701 spin_unlock_irqrestore(&udc->lock, flags); 702 703 return 0; 704 } 705 706 static struct usb_request * 707 usba_ep_alloc_request(struct usb_ep *_ep, gfp_t gfp_flags) 708 { 709 struct usba_request *req; 710 711 DBG(DBG_GADGET, "ep_alloc_request: %p, 0x%x\n", _ep, gfp_flags); 712 713 req = kzalloc(sizeof(*req), gfp_flags); 714 if (!req) 715 return NULL; 716 717 INIT_LIST_HEAD(&req->queue); 718 719 return &req->req; 720 } 721 722 static void 723 usba_ep_free_request(struct usb_ep *_ep, struct usb_request *_req) 724 { 725 struct usba_request *req = to_usba_req(_req); 726 727 DBG(DBG_GADGET, "ep_free_request: %p, %p\n", _ep, _req); 728 729 kfree(req); 730 } 731 732 static int queue_dma(struct usba_udc *udc, struct usba_ep *ep, 733 struct usba_request *req, gfp_t gfp_flags) 734 { 735 unsigned long flags; 736 int ret; 737 738 DBG(DBG_DMA, "%s: req l/%u d/%pad %c%c%c\n", 739 ep->ep.name, req->req.length, &req->req.dma, 740 req->req.zero ? 'Z' : 'z', 741 req->req.short_not_ok ? 'S' : 's', 742 req->req.no_interrupt ? 'I' : 'i'); 743 744 if (req->req.length > 0x10000) { 745 /* Lengths from 0 to 65536 (inclusive) are supported */ 746 DBG(DBG_ERR, "invalid request length %u\n", req->req.length); 747 return -EINVAL; 748 } 749 750 ret = usb_gadget_map_request(&udc->gadget, &req->req, ep->is_in); 751 if (ret) 752 return ret; 753 754 req->using_dma = 1; 755 req->ctrl = USBA_BF(DMA_BUF_LEN, req->req.length) 756 | USBA_DMA_CH_EN | USBA_DMA_END_BUF_IE 757 | USBA_DMA_END_BUF_EN; 758 759 if (!ep->is_in) 760 req->ctrl |= USBA_DMA_END_TR_EN | USBA_DMA_END_TR_IE; 761 762 /* 763 * Add this request to the queue and submit for DMA if 764 * possible. Check if we're still alive first -- we may have 765 * received a reset since last time we checked. 766 */ 767 ret = -ESHUTDOWN; 768 spin_lock_irqsave(&udc->lock, flags); 769 if (ep->ep.desc) { 770 if (list_empty(&ep->queue)) 771 submit_request(ep, req); 772 773 list_add_tail(&req->queue, &ep->queue); 774 ret = 0; 775 } 776 spin_unlock_irqrestore(&udc->lock, flags); 777 778 return ret; 779 } 780 781 static int 782 usba_ep_queue(struct usb_ep *_ep, struct usb_request *_req, gfp_t gfp_flags) 783 { 784 struct usba_request *req = to_usba_req(_req); 785 struct usba_ep *ep = to_usba_ep(_ep); 786 struct usba_udc *udc = ep->udc; 787 unsigned long flags; 788 int ret; 789 790 DBG(DBG_GADGET | DBG_QUEUE | DBG_REQ, "%s: queue req %p, len %u\n", 791 ep->ep.name, req, _req->length); 792 793 if (!udc->driver || udc->gadget.speed == USB_SPEED_UNKNOWN || 794 !ep->ep.desc) 795 return -ESHUTDOWN; 796 797 req->submitted = 0; 798 req->using_dma = 0; 799 req->last_transaction = 0; 800 801 _req->status = -EINPROGRESS; 802 _req->actual = 0; 803 804 if (ep->can_dma) 805 return queue_dma(udc, ep, req, gfp_flags); 806 807 /* May have received a reset since last time we checked */ 808 ret = -ESHUTDOWN; 809 spin_lock_irqsave(&udc->lock, flags); 810 if (ep->ep.desc) { 811 list_add_tail(&req->queue, &ep->queue); 812 813 if ((!ep_is_control(ep) && ep->is_in) || 814 (ep_is_control(ep) 815 && (ep->state == DATA_STAGE_IN 816 || ep->state == STATUS_STAGE_IN))) 817 usba_ep_writel(ep, CTL_ENB, USBA_TX_PK_RDY); 818 else 819 usba_ep_writel(ep, CTL_ENB, USBA_RX_BK_RDY); 820 ret = 0; 821 } 822 spin_unlock_irqrestore(&udc->lock, flags); 823 824 return ret; 825 } 826 827 static void 828 usba_update_req(struct usba_ep *ep, struct usba_request *req, u32 status) 829 { 830 req->req.actual = req->req.length - USBA_BFEXT(DMA_BUF_LEN, status); 831 } 832 833 static int stop_dma(struct usba_ep *ep, u32 *pstatus) 834 { 835 unsigned int timeout; 836 u32 status; 837 838 /* 839 * Stop the DMA controller. When writing both CH_EN 840 * and LINK to 0, the other bits are not affected. 841 */ 842 usba_dma_writel(ep, CONTROL, 0); 843 844 /* Wait for the FIFO to empty */ 845 for (timeout = 40; timeout; --timeout) { 846 status = usba_dma_readl(ep, STATUS); 847 if (!(status & USBA_DMA_CH_EN)) 848 break; 849 udelay(1); 850 } 851 852 if (pstatus) 853 *pstatus = status; 854 855 if (timeout == 0) { 856 dev_err(&ep->udc->pdev->dev, 857 "%s: timed out waiting for DMA FIFO to empty\n", 858 ep->ep.name); 859 return -ETIMEDOUT; 860 } 861 862 return 0; 863 } 864 865 static int usba_ep_dequeue(struct usb_ep *_ep, struct usb_request *_req) 866 { 867 struct usba_ep *ep = to_usba_ep(_ep); 868 struct usba_udc *udc = ep->udc; 869 struct usba_request *req; 870 unsigned long flags; 871 u32 status; 872 873 DBG(DBG_GADGET | DBG_QUEUE, "ep_dequeue: %s, req %p\n", 874 ep->ep.name, req); 875 876 spin_lock_irqsave(&udc->lock, flags); 877 878 list_for_each_entry(req, &ep->queue, queue) { 879 if (&req->req == _req) 880 break; 881 } 882 883 if (&req->req != _req) { 884 spin_unlock_irqrestore(&udc->lock, flags); 885 return -EINVAL; 886 } 887 888 if (req->using_dma) { 889 /* 890 * If this request is currently being transferred, 891 * stop the DMA controller and reset the FIFO. 892 */ 893 if (ep->queue.next == &req->queue) { 894 status = usba_dma_readl(ep, STATUS); 895 if (status & USBA_DMA_CH_EN) 896 stop_dma(ep, &status); 897 898 #ifdef CONFIG_USB_GADGET_DEBUG_FS 899 ep->last_dma_status = status; 900 #endif 901 902 usba_writel(udc, EPT_RST, 1 << ep->index); 903 904 usba_update_req(ep, req, status); 905 } 906 } 907 908 /* 909 * Errors should stop the queue from advancing until the 910 * completion function returns. 911 */ 912 list_del_init(&req->queue); 913 914 request_complete(ep, req, -ECONNRESET); 915 916 /* Process the next request if any */ 917 submit_next_request(ep); 918 spin_unlock_irqrestore(&udc->lock, flags); 919 920 return 0; 921 } 922 923 static int usba_ep_set_halt(struct usb_ep *_ep, int value) 924 { 925 struct usba_ep *ep = to_usba_ep(_ep); 926 struct usba_udc *udc = ep->udc; 927 unsigned long flags; 928 int ret = 0; 929 930 DBG(DBG_GADGET, "endpoint %s: %s HALT\n", ep->ep.name, 931 value ? "set" : "clear"); 932 933 if (!ep->ep.desc) { 934 DBG(DBG_ERR, "Attempted to halt uninitialized ep %s\n", 935 ep->ep.name); 936 return -ENODEV; 937 } 938 if (ep->is_isoc) { 939 DBG(DBG_ERR, "Attempted to halt isochronous ep %s\n", 940 ep->ep.name); 941 return -ENOTTY; 942 } 943 944 spin_lock_irqsave(&udc->lock, flags); 945 946 /* 947 * We can't halt IN endpoints while there are still data to be 948 * transferred 949 */ 950 if (!list_empty(&ep->queue) 951 || ((value && ep->is_in && (usba_ep_readl(ep, STA) 952 & USBA_BF(BUSY_BANKS, -1L))))) { 953 ret = -EAGAIN; 954 } else { 955 if (value) 956 usba_ep_writel(ep, SET_STA, USBA_FORCE_STALL); 957 else 958 usba_ep_writel(ep, CLR_STA, 959 USBA_FORCE_STALL | USBA_TOGGLE_CLR); 960 usba_ep_readl(ep, STA); 961 } 962 963 spin_unlock_irqrestore(&udc->lock, flags); 964 965 return ret; 966 } 967 968 static int usba_ep_fifo_status(struct usb_ep *_ep) 969 { 970 struct usba_ep *ep = to_usba_ep(_ep); 971 972 return USBA_BFEXT(BYTE_COUNT, usba_ep_readl(ep, STA)); 973 } 974 975 static void usba_ep_fifo_flush(struct usb_ep *_ep) 976 { 977 struct usba_ep *ep = to_usba_ep(_ep); 978 struct usba_udc *udc = ep->udc; 979 980 usba_writel(udc, EPT_RST, 1 << ep->index); 981 } 982 983 static const struct usb_ep_ops usba_ep_ops = { 984 .enable = usba_ep_enable, 985 .disable = usba_ep_disable, 986 .alloc_request = usba_ep_alloc_request, 987 .free_request = usba_ep_free_request, 988 .queue = usba_ep_queue, 989 .dequeue = usba_ep_dequeue, 990 .set_halt = usba_ep_set_halt, 991 .fifo_status = usba_ep_fifo_status, 992 .fifo_flush = usba_ep_fifo_flush, 993 }; 994 995 static int usba_udc_get_frame(struct usb_gadget *gadget) 996 { 997 struct usba_udc *udc = to_usba_udc(gadget); 998 999 return USBA_BFEXT(FRAME_NUMBER, usba_readl(udc, FNUM)); 1000 } 1001 1002 static int usba_udc_wakeup(struct usb_gadget *gadget) 1003 { 1004 struct usba_udc *udc = to_usba_udc(gadget); 1005 unsigned long flags; 1006 u32 ctrl; 1007 int ret = -EINVAL; 1008 1009 spin_lock_irqsave(&udc->lock, flags); 1010 if (udc->devstatus & (1 << USB_DEVICE_REMOTE_WAKEUP)) { 1011 ctrl = usba_readl(udc, CTRL); 1012 usba_writel(udc, CTRL, ctrl | USBA_REMOTE_WAKE_UP); 1013 ret = 0; 1014 } 1015 spin_unlock_irqrestore(&udc->lock, flags); 1016 1017 return ret; 1018 } 1019 1020 static int 1021 usba_udc_set_selfpowered(struct usb_gadget *gadget, int is_selfpowered) 1022 { 1023 struct usba_udc *udc = to_usba_udc(gadget); 1024 unsigned long flags; 1025 1026 gadget->is_selfpowered = (is_selfpowered != 0); 1027 spin_lock_irqsave(&udc->lock, flags); 1028 if (is_selfpowered) 1029 udc->devstatus |= 1 << USB_DEVICE_SELF_POWERED; 1030 else 1031 udc->devstatus &= ~(1 << USB_DEVICE_SELF_POWERED); 1032 spin_unlock_irqrestore(&udc->lock, flags); 1033 1034 return 0; 1035 } 1036 1037 static int atmel_usba_start(struct usb_gadget *gadget, 1038 struct usb_gadget_driver *driver); 1039 static int atmel_usba_stop(struct usb_gadget *gadget); 1040 1041 static struct usb_ep *atmel_usba_match_ep(struct usb_gadget *gadget, 1042 struct usb_endpoint_descriptor *desc, 1043 struct usb_ss_ep_comp_descriptor *ep_comp) 1044 { 1045 struct usb_ep *_ep; 1046 struct usba_ep *ep; 1047 1048 /* Look at endpoints until an unclaimed one looks usable */ 1049 list_for_each_entry(_ep, &gadget->ep_list, ep_list) { 1050 if (usb_gadget_ep_match_desc(gadget, _ep, desc, ep_comp)) 1051 goto found_ep; 1052 } 1053 /* Fail */ 1054 return NULL; 1055 1056 found_ep: 1057 1058 if (fifo_mode == 0) { 1059 /* Optimize hw fifo size based on ep type and other info */ 1060 ep = to_usba_ep(_ep); 1061 1062 switch (usb_endpoint_type(desc)) { 1063 case USB_ENDPOINT_XFER_CONTROL: 1064 break; 1065 1066 case USB_ENDPOINT_XFER_ISOC: 1067 ep->fifo_size = 1024; 1068 ep->nr_banks = 2; 1069 break; 1070 1071 case USB_ENDPOINT_XFER_BULK: 1072 ep->fifo_size = 512; 1073 ep->nr_banks = 1; 1074 break; 1075 1076 case USB_ENDPOINT_XFER_INT: 1077 if (desc->wMaxPacketSize == 0) 1078 ep->fifo_size = 1079 roundup_pow_of_two(_ep->maxpacket_limit); 1080 else 1081 ep->fifo_size = 1082 roundup_pow_of_two(le16_to_cpu(desc->wMaxPacketSize)); 1083 ep->nr_banks = 1; 1084 break; 1085 } 1086 1087 /* It might be a little bit late to set this */ 1088 usb_ep_set_maxpacket_limit(&ep->ep, ep->fifo_size); 1089 1090 /* Generate ept_cfg basd on FIFO size and number of banks */ 1091 if (ep->fifo_size <= 8) 1092 ep->ept_cfg = USBA_BF(EPT_SIZE, USBA_EPT_SIZE_8); 1093 else 1094 /* LSB is bit 1, not 0 */ 1095 ep->ept_cfg = 1096 USBA_BF(EPT_SIZE, fls(ep->fifo_size - 1) - 3); 1097 1098 ep->ept_cfg |= USBA_BF(BK_NUMBER, ep->nr_banks); 1099 1100 ep->udc->configured_ep++; 1101 } 1102 1103 return _ep; 1104 } 1105 1106 static const struct usb_gadget_ops usba_udc_ops = { 1107 .get_frame = usba_udc_get_frame, 1108 .wakeup = usba_udc_wakeup, 1109 .set_selfpowered = usba_udc_set_selfpowered, 1110 .udc_start = atmel_usba_start, 1111 .udc_stop = atmel_usba_stop, 1112 .match_ep = atmel_usba_match_ep, 1113 }; 1114 1115 static struct usb_endpoint_descriptor usba_ep0_desc = { 1116 .bLength = USB_DT_ENDPOINT_SIZE, 1117 .bDescriptorType = USB_DT_ENDPOINT, 1118 .bEndpointAddress = 0, 1119 .bmAttributes = USB_ENDPOINT_XFER_CONTROL, 1120 .wMaxPacketSize = cpu_to_le16(64), 1121 /* FIXME: I have no idea what to put here */ 1122 .bInterval = 1, 1123 }; 1124 1125 static struct usb_gadget usba_gadget_template = { 1126 .ops = &usba_udc_ops, 1127 .max_speed = USB_SPEED_HIGH, 1128 .name = "atmel_usba_udc", 1129 }; 1130 1131 /* 1132 * Called with interrupts disabled and udc->lock held. 1133 */ 1134 static void reset_all_endpoints(struct usba_udc *udc) 1135 { 1136 struct usba_ep *ep; 1137 struct usba_request *req, *tmp_req; 1138 1139 usba_writel(udc, EPT_RST, ~0UL); 1140 1141 ep = to_usba_ep(udc->gadget.ep0); 1142 list_for_each_entry_safe(req, tmp_req, &ep->queue, queue) { 1143 list_del_init(&req->queue); 1144 request_complete(ep, req, -ECONNRESET); 1145 } 1146 } 1147 1148 static struct usba_ep *get_ep_by_addr(struct usba_udc *udc, u16 wIndex) 1149 { 1150 struct usba_ep *ep; 1151 1152 if ((wIndex & USB_ENDPOINT_NUMBER_MASK) == 0) 1153 return to_usba_ep(udc->gadget.ep0); 1154 1155 list_for_each_entry (ep, &udc->gadget.ep_list, ep.ep_list) { 1156 u8 bEndpointAddress; 1157 1158 if (!ep->ep.desc) 1159 continue; 1160 bEndpointAddress = ep->ep.desc->bEndpointAddress; 1161 if ((wIndex ^ bEndpointAddress) & USB_DIR_IN) 1162 continue; 1163 if ((bEndpointAddress & USB_ENDPOINT_NUMBER_MASK) 1164 == (wIndex & USB_ENDPOINT_NUMBER_MASK)) 1165 return ep; 1166 } 1167 1168 return NULL; 1169 } 1170 1171 /* Called with interrupts disabled and udc->lock held */ 1172 static inline void set_protocol_stall(struct usba_udc *udc, struct usba_ep *ep) 1173 { 1174 usba_ep_writel(ep, SET_STA, USBA_FORCE_STALL); 1175 ep->state = WAIT_FOR_SETUP; 1176 } 1177 1178 static inline int is_stalled(struct usba_udc *udc, struct usba_ep *ep) 1179 { 1180 if (usba_ep_readl(ep, STA) & USBA_FORCE_STALL) 1181 return 1; 1182 return 0; 1183 } 1184 1185 static inline void set_address(struct usba_udc *udc, unsigned int addr) 1186 { 1187 u32 regval; 1188 1189 DBG(DBG_BUS, "setting address %u...\n", addr); 1190 regval = usba_readl(udc, CTRL); 1191 regval = USBA_BFINS(DEV_ADDR, addr, regval); 1192 usba_writel(udc, CTRL, regval); 1193 } 1194 1195 static int do_test_mode(struct usba_udc *udc) 1196 { 1197 static const char test_packet_buffer[] = { 1198 /* JKJKJKJK * 9 */ 1199 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 1200 /* JJKKJJKK * 8 */ 1201 0xAA, 0xAA, 0xAA, 0xAA, 0xAA, 0xAA, 0xAA, 0xAA, 1202 /* JJKKJJKK * 8 */ 1203 0xEE, 0xEE, 0xEE, 0xEE, 0xEE, 0xEE, 0xEE, 0xEE, 1204 /* JJJJJJJKKKKKKK * 8 */ 1205 0xFE, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 1206 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 1207 /* JJJJJJJK * 8 */ 1208 0x7F, 0xBF, 0xDF, 0xEF, 0xF7, 0xFB, 0xFD, 1209 /* {JKKKKKKK * 10}, JK */ 1210 0xFC, 0x7E, 0xBF, 0xDF, 0xEF, 0xF7, 0xFB, 0xFD, 0x7E 1211 }; 1212 struct usba_ep *ep; 1213 struct device *dev = &udc->pdev->dev; 1214 int test_mode; 1215 1216 test_mode = udc->test_mode; 1217 1218 /* Start from a clean slate */ 1219 reset_all_endpoints(udc); 1220 1221 switch (test_mode) { 1222 case 0x0100: 1223 /* Test_J */ 1224 usba_writel(udc, TST, USBA_TST_J_MODE); 1225 dev_info(dev, "Entering Test_J mode...\n"); 1226 break; 1227 case 0x0200: 1228 /* Test_K */ 1229 usba_writel(udc, TST, USBA_TST_K_MODE); 1230 dev_info(dev, "Entering Test_K mode...\n"); 1231 break; 1232 case 0x0300: 1233 /* 1234 * Test_SE0_NAK: Force high-speed mode and set up ep0 1235 * for Bulk IN transfers 1236 */ 1237 ep = &udc->usba_ep[0]; 1238 usba_writel(udc, TST, 1239 USBA_BF(SPEED_CFG, USBA_SPEED_CFG_FORCE_HIGH)); 1240 usba_ep_writel(ep, CFG, 1241 USBA_BF(EPT_SIZE, USBA_EPT_SIZE_64) 1242 | USBA_EPT_DIR_IN 1243 | USBA_BF(EPT_TYPE, USBA_EPT_TYPE_BULK) 1244 | USBA_BF(BK_NUMBER, 1)); 1245 if (!(usba_ep_readl(ep, CFG) & USBA_EPT_MAPPED)) { 1246 set_protocol_stall(udc, ep); 1247 dev_err(dev, "Test_SE0_NAK: ep0 not mapped\n"); 1248 } else { 1249 usba_ep_writel(ep, CTL_ENB, USBA_EPT_ENABLE); 1250 dev_info(dev, "Entering Test_SE0_NAK mode...\n"); 1251 } 1252 break; 1253 case 0x0400: 1254 /* Test_Packet */ 1255 ep = &udc->usba_ep[0]; 1256 usba_ep_writel(ep, CFG, 1257 USBA_BF(EPT_SIZE, USBA_EPT_SIZE_64) 1258 | USBA_EPT_DIR_IN 1259 | USBA_BF(EPT_TYPE, USBA_EPT_TYPE_BULK) 1260 | USBA_BF(BK_NUMBER, 1)); 1261 if (!(usba_ep_readl(ep, CFG) & USBA_EPT_MAPPED)) { 1262 set_protocol_stall(udc, ep); 1263 dev_err(dev, "Test_Packet: ep0 not mapped\n"); 1264 } else { 1265 usba_ep_writel(ep, CTL_ENB, USBA_EPT_ENABLE); 1266 usba_writel(udc, TST, USBA_TST_PKT_MODE); 1267 memcpy_toio(ep->fifo, test_packet_buffer, 1268 sizeof(test_packet_buffer)); 1269 usba_ep_writel(ep, SET_STA, USBA_TX_PK_RDY); 1270 dev_info(dev, "Entering Test_Packet mode...\n"); 1271 } 1272 break; 1273 default: 1274 dev_err(dev, "Invalid test mode: 0x%04x\n", test_mode); 1275 return -EINVAL; 1276 } 1277 1278 return 0; 1279 } 1280 1281 /* Avoid overly long expressions */ 1282 static inline bool feature_is_dev_remote_wakeup(struct usb_ctrlrequest *crq) 1283 { 1284 if (crq->wValue == cpu_to_le16(USB_DEVICE_REMOTE_WAKEUP)) 1285 return true; 1286 return false; 1287 } 1288 1289 static inline bool feature_is_dev_test_mode(struct usb_ctrlrequest *crq) 1290 { 1291 if (crq->wValue == cpu_to_le16(USB_DEVICE_TEST_MODE)) 1292 return true; 1293 return false; 1294 } 1295 1296 static inline bool feature_is_ep_halt(struct usb_ctrlrequest *crq) 1297 { 1298 if (crq->wValue == cpu_to_le16(USB_ENDPOINT_HALT)) 1299 return true; 1300 return false; 1301 } 1302 1303 static int handle_ep0_setup(struct usba_udc *udc, struct usba_ep *ep, 1304 struct usb_ctrlrequest *crq) 1305 { 1306 int retval = 0; 1307 1308 switch (crq->bRequest) { 1309 case USB_REQ_GET_STATUS: { 1310 u16 status; 1311 1312 if (crq->bRequestType == (USB_DIR_IN | USB_RECIP_DEVICE)) { 1313 status = cpu_to_le16(udc->devstatus); 1314 } else if (crq->bRequestType 1315 == (USB_DIR_IN | USB_RECIP_INTERFACE)) { 1316 status = cpu_to_le16(0); 1317 } else if (crq->bRequestType 1318 == (USB_DIR_IN | USB_RECIP_ENDPOINT)) { 1319 struct usba_ep *target; 1320 1321 target = get_ep_by_addr(udc, le16_to_cpu(crq->wIndex)); 1322 if (!target) 1323 goto stall; 1324 1325 status = 0; 1326 if (is_stalled(udc, target)) 1327 status |= cpu_to_le16(1); 1328 } else 1329 goto delegate; 1330 1331 /* Write directly to the FIFO. No queueing is done. */ 1332 if (crq->wLength != cpu_to_le16(sizeof(status))) 1333 goto stall; 1334 ep->state = DATA_STAGE_IN; 1335 writew_relaxed(status, ep->fifo); 1336 usba_ep_writel(ep, SET_STA, USBA_TX_PK_RDY); 1337 break; 1338 } 1339 1340 case USB_REQ_CLEAR_FEATURE: { 1341 if (crq->bRequestType == USB_RECIP_DEVICE) { 1342 if (feature_is_dev_remote_wakeup(crq)) 1343 udc->devstatus 1344 &= ~(1 << USB_DEVICE_REMOTE_WAKEUP); 1345 else 1346 /* Can't CLEAR_FEATURE TEST_MODE */ 1347 goto stall; 1348 } else if (crq->bRequestType == USB_RECIP_ENDPOINT) { 1349 struct usba_ep *target; 1350 1351 if (crq->wLength != cpu_to_le16(0) 1352 || !feature_is_ep_halt(crq)) 1353 goto stall; 1354 target = get_ep_by_addr(udc, le16_to_cpu(crq->wIndex)); 1355 if (!target) 1356 goto stall; 1357 1358 usba_ep_writel(target, CLR_STA, USBA_FORCE_STALL); 1359 if (target->index != 0) 1360 usba_ep_writel(target, CLR_STA, 1361 USBA_TOGGLE_CLR); 1362 } else { 1363 goto delegate; 1364 } 1365 1366 send_status(udc, ep); 1367 break; 1368 } 1369 1370 case USB_REQ_SET_FEATURE: { 1371 if (crq->bRequestType == USB_RECIP_DEVICE) { 1372 if (feature_is_dev_test_mode(crq)) { 1373 send_status(udc, ep); 1374 ep->state = STATUS_STAGE_TEST; 1375 udc->test_mode = le16_to_cpu(crq->wIndex); 1376 return 0; 1377 } else if (feature_is_dev_remote_wakeup(crq)) { 1378 udc->devstatus |= 1 << USB_DEVICE_REMOTE_WAKEUP; 1379 } else { 1380 goto stall; 1381 } 1382 } else if (crq->bRequestType == USB_RECIP_ENDPOINT) { 1383 struct usba_ep *target; 1384 1385 if (crq->wLength != cpu_to_le16(0) 1386 || !feature_is_ep_halt(crq)) 1387 goto stall; 1388 1389 target = get_ep_by_addr(udc, le16_to_cpu(crq->wIndex)); 1390 if (!target) 1391 goto stall; 1392 1393 usba_ep_writel(target, SET_STA, USBA_FORCE_STALL); 1394 } else 1395 goto delegate; 1396 1397 send_status(udc, ep); 1398 break; 1399 } 1400 1401 case USB_REQ_SET_ADDRESS: 1402 if (crq->bRequestType != (USB_DIR_OUT | USB_RECIP_DEVICE)) 1403 goto delegate; 1404 1405 set_address(udc, le16_to_cpu(crq->wValue)); 1406 send_status(udc, ep); 1407 ep->state = STATUS_STAGE_ADDR; 1408 break; 1409 1410 default: 1411 delegate: 1412 spin_unlock(&udc->lock); 1413 retval = udc->driver->setup(&udc->gadget, crq); 1414 spin_lock(&udc->lock); 1415 } 1416 1417 return retval; 1418 1419 stall: 1420 pr_err("udc: %s: Invalid setup request: %02x.%02x v%04x i%04x l%d, " 1421 "halting endpoint...\n", 1422 ep->ep.name, crq->bRequestType, crq->bRequest, 1423 le16_to_cpu(crq->wValue), le16_to_cpu(crq->wIndex), 1424 le16_to_cpu(crq->wLength)); 1425 set_protocol_stall(udc, ep); 1426 return -1; 1427 } 1428 1429 static void usba_control_irq(struct usba_udc *udc, struct usba_ep *ep) 1430 { 1431 struct usba_request *req; 1432 u32 epstatus; 1433 u32 epctrl; 1434 1435 restart: 1436 epstatus = usba_ep_readl(ep, STA); 1437 epctrl = usba_ep_readl(ep, CTL); 1438 1439 DBG(DBG_INT, "%s [%d]: s/%08x c/%08x\n", 1440 ep->ep.name, ep->state, epstatus, epctrl); 1441 1442 req = NULL; 1443 if (!list_empty(&ep->queue)) 1444 req = list_entry(ep->queue.next, 1445 struct usba_request, queue); 1446 1447 if ((epctrl & USBA_TX_PK_RDY) && !(epstatus & USBA_TX_PK_RDY)) { 1448 if (req->submitted) 1449 next_fifo_transaction(ep, req); 1450 else 1451 submit_request(ep, req); 1452 1453 if (req->last_transaction) { 1454 usba_ep_writel(ep, CTL_DIS, USBA_TX_PK_RDY); 1455 usba_ep_writel(ep, CTL_ENB, USBA_TX_COMPLETE); 1456 } 1457 goto restart; 1458 } 1459 if ((epstatus & epctrl) & USBA_TX_COMPLETE) { 1460 usba_ep_writel(ep, CLR_STA, USBA_TX_COMPLETE); 1461 1462 switch (ep->state) { 1463 case DATA_STAGE_IN: 1464 usba_ep_writel(ep, CTL_ENB, USBA_RX_BK_RDY); 1465 usba_ep_writel(ep, CTL_DIS, USBA_TX_COMPLETE); 1466 ep->state = STATUS_STAGE_OUT; 1467 break; 1468 case STATUS_STAGE_ADDR: 1469 /* Activate our new address */ 1470 usba_writel(udc, CTRL, (usba_readl(udc, CTRL) 1471 | USBA_FADDR_EN)); 1472 usba_ep_writel(ep, CTL_DIS, USBA_TX_COMPLETE); 1473 ep->state = WAIT_FOR_SETUP; 1474 break; 1475 case STATUS_STAGE_IN: 1476 if (req) { 1477 list_del_init(&req->queue); 1478 request_complete(ep, req, 0); 1479 submit_next_request(ep); 1480 } 1481 usba_ep_writel(ep, CTL_DIS, USBA_TX_COMPLETE); 1482 ep->state = WAIT_FOR_SETUP; 1483 break; 1484 case STATUS_STAGE_TEST: 1485 usba_ep_writel(ep, CTL_DIS, USBA_TX_COMPLETE); 1486 ep->state = WAIT_FOR_SETUP; 1487 if (do_test_mode(udc)) 1488 set_protocol_stall(udc, ep); 1489 break; 1490 default: 1491 pr_err("udc: %s: TXCOMP: Invalid endpoint state %d, " 1492 "halting endpoint...\n", 1493 ep->ep.name, ep->state); 1494 set_protocol_stall(udc, ep); 1495 break; 1496 } 1497 1498 goto restart; 1499 } 1500 if ((epstatus & epctrl) & USBA_RX_BK_RDY) { 1501 switch (ep->state) { 1502 case STATUS_STAGE_OUT: 1503 usba_ep_writel(ep, CLR_STA, USBA_RX_BK_RDY); 1504 usba_ep_writel(ep, CTL_DIS, USBA_RX_BK_RDY); 1505 1506 if (req) { 1507 list_del_init(&req->queue); 1508 request_complete(ep, req, 0); 1509 } 1510 ep->state = WAIT_FOR_SETUP; 1511 break; 1512 1513 case DATA_STAGE_OUT: 1514 receive_data(ep); 1515 break; 1516 1517 default: 1518 usba_ep_writel(ep, CLR_STA, USBA_RX_BK_RDY); 1519 usba_ep_writel(ep, CTL_DIS, USBA_RX_BK_RDY); 1520 pr_err("udc: %s: RXRDY: Invalid endpoint state %d, " 1521 "halting endpoint...\n", 1522 ep->ep.name, ep->state); 1523 set_protocol_stall(udc, ep); 1524 break; 1525 } 1526 1527 goto restart; 1528 } 1529 if (epstatus & USBA_RX_SETUP) { 1530 union { 1531 struct usb_ctrlrequest crq; 1532 unsigned long data[2]; 1533 } crq; 1534 unsigned int pkt_len; 1535 int ret; 1536 1537 if (ep->state != WAIT_FOR_SETUP) { 1538 /* 1539 * Didn't expect a SETUP packet at this 1540 * point. Clean up any pending requests (which 1541 * may be successful). 1542 */ 1543 int status = -EPROTO; 1544 1545 /* 1546 * RXRDY and TXCOMP are dropped when SETUP 1547 * packets arrive. Just pretend we received 1548 * the status packet. 1549 */ 1550 if (ep->state == STATUS_STAGE_OUT 1551 || ep->state == STATUS_STAGE_IN) { 1552 usba_ep_writel(ep, CTL_DIS, USBA_RX_BK_RDY); 1553 status = 0; 1554 } 1555 1556 if (req) { 1557 list_del_init(&req->queue); 1558 request_complete(ep, req, status); 1559 } 1560 } 1561 1562 pkt_len = USBA_BFEXT(BYTE_COUNT, usba_ep_readl(ep, STA)); 1563 DBG(DBG_HW, "Packet length: %u\n", pkt_len); 1564 if (pkt_len != sizeof(crq)) { 1565 pr_warn("udc: Invalid packet length %u (expected %zu)\n", 1566 pkt_len, sizeof(crq)); 1567 set_protocol_stall(udc, ep); 1568 return; 1569 } 1570 1571 DBG(DBG_FIFO, "Copying ctrl request from 0x%p:\n", ep->fifo); 1572 memcpy_fromio(crq.data, ep->fifo, sizeof(crq)); 1573 1574 /* Free up one bank in the FIFO so that we can 1575 * generate or receive a reply right away. */ 1576 usba_ep_writel(ep, CLR_STA, USBA_RX_SETUP); 1577 1578 /* printk(KERN_DEBUG "setup: %d: %02x.%02x\n", 1579 ep->state, crq.crq.bRequestType, 1580 crq.crq.bRequest); */ 1581 1582 if (crq.crq.bRequestType & USB_DIR_IN) { 1583 /* 1584 * The USB 2.0 spec states that "if wLength is 1585 * zero, there is no data transfer phase." 1586 * However, testusb #14 seems to actually 1587 * expect a data phase even if wLength = 0... 1588 */ 1589 ep->state = DATA_STAGE_IN; 1590 } else { 1591 if (crq.crq.wLength != cpu_to_le16(0)) 1592 ep->state = DATA_STAGE_OUT; 1593 else 1594 ep->state = STATUS_STAGE_IN; 1595 } 1596 1597 ret = -1; 1598 if (ep->index == 0) 1599 ret = handle_ep0_setup(udc, ep, &crq.crq); 1600 else { 1601 spin_unlock(&udc->lock); 1602 ret = udc->driver->setup(&udc->gadget, &crq.crq); 1603 spin_lock(&udc->lock); 1604 } 1605 1606 DBG(DBG_BUS, "req %02x.%02x, length %d, state %d, ret %d\n", 1607 crq.crq.bRequestType, crq.crq.bRequest, 1608 le16_to_cpu(crq.crq.wLength), ep->state, ret); 1609 1610 if (ret < 0) { 1611 /* Let the host know that we failed */ 1612 set_protocol_stall(udc, ep); 1613 } 1614 } 1615 } 1616 1617 static void usba_ep_irq(struct usba_udc *udc, struct usba_ep *ep) 1618 { 1619 struct usba_request *req; 1620 u32 epstatus; 1621 u32 epctrl; 1622 1623 epstatus = usba_ep_readl(ep, STA); 1624 epctrl = usba_ep_readl(ep, CTL); 1625 1626 DBG(DBG_INT, "%s: interrupt, status: 0x%08x\n", ep->ep.name, epstatus); 1627 1628 while ((epctrl & USBA_TX_PK_RDY) && !(epstatus & USBA_TX_PK_RDY)) { 1629 DBG(DBG_BUS, "%s: TX PK ready\n", ep->ep.name); 1630 1631 if (list_empty(&ep->queue)) { 1632 dev_warn(&udc->pdev->dev, "ep_irq: queue empty\n"); 1633 usba_ep_writel(ep, CTL_DIS, USBA_TX_PK_RDY); 1634 return; 1635 } 1636 1637 req = list_entry(ep->queue.next, struct usba_request, queue); 1638 1639 if (req->using_dma) { 1640 /* Send a zero-length packet */ 1641 usba_ep_writel(ep, SET_STA, 1642 USBA_TX_PK_RDY); 1643 usba_ep_writel(ep, CTL_DIS, 1644 USBA_TX_PK_RDY); 1645 list_del_init(&req->queue); 1646 submit_next_request(ep); 1647 request_complete(ep, req, 0); 1648 } else { 1649 if (req->submitted) 1650 next_fifo_transaction(ep, req); 1651 else 1652 submit_request(ep, req); 1653 1654 if (req->last_transaction) { 1655 list_del_init(&req->queue); 1656 submit_next_request(ep); 1657 request_complete(ep, req, 0); 1658 } 1659 } 1660 1661 epstatus = usba_ep_readl(ep, STA); 1662 epctrl = usba_ep_readl(ep, CTL); 1663 } 1664 if ((epstatus & epctrl) & USBA_RX_BK_RDY) { 1665 DBG(DBG_BUS, "%s: RX data ready\n", ep->ep.name); 1666 receive_data(ep); 1667 } 1668 } 1669 1670 static void usba_dma_irq(struct usba_udc *udc, struct usba_ep *ep) 1671 { 1672 struct usba_request *req; 1673 u32 status, control, pending; 1674 1675 status = usba_dma_readl(ep, STATUS); 1676 control = usba_dma_readl(ep, CONTROL); 1677 #ifdef CONFIG_USB_GADGET_DEBUG_FS 1678 ep->last_dma_status = status; 1679 #endif 1680 pending = status & control; 1681 DBG(DBG_INT | DBG_DMA, "dma irq, s/%#08x, c/%#08x\n", status, control); 1682 1683 if (status & USBA_DMA_CH_EN) { 1684 dev_err(&udc->pdev->dev, 1685 "DMA_CH_EN is set after transfer is finished!\n"); 1686 dev_err(&udc->pdev->dev, 1687 "status=%#08x, pending=%#08x, control=%#08x\n", 1688 status, pending, control); 1689 1690 /* 1691 * try to pretend nothing happened. We might have to 1692 * do something here... 1693 */ 1694 } 1695 1696 if (list_empty(&ep->queue)) 1697 /* Might happen if a reset comes along at the right moment */ 1698 return; 1699 1700 if (pending & (USBA_DMA_END_TR_ST | USBA_DMA_END_BUF_ST)) { 1701 req = list_entry(ep->queue.next, struct usba_request, queue); 1702 usba_update_req(ep, req, status); 1703 1704 list_del_init(&req->queue); 1705 submit_next_request(ep); 1706 request_complete(ep, req, 0); 1707 } 1708 } 1709 1710 static int start_clock(struct usba_udc *udc); 1711 static void stop_clock(struct usba_udc *udc); 1712 1713 static irqreturn_t usba_udc_irq(int irq, void *devid) 1714 { 1715 struct usba_udc *udc = devid; 1716 u32 status, int_enb; 1717 u32 dma_status; 1718 u32 ep_status; 1719 1720 spin_lock(&udc->lock); 1721 1722 int_enb = usba_int_enb_get(udc); 1723 status = usba_readl(udc, INT_STA) & (int_enb | USBA_HIGH_SPEED); 1724 DBG(DBG_INT, "irq, status=%#08x\n", status); 1725 1726 if (status & USBA_DET_SUSPEND) { 1727 usba_writel(udc, INT_CLR, USBA_DET_SUSPEND|USBA_WAKE_UP); 1728 usba_int_enb_set(udc, USBA_WAKE_UP); 1729 usba_int_enb_clear(udc, USBA_DET_SUSPEND); 1730 udc->suspended = true; 1731 toggle_bias(udc, 0); 1732 udc->bias_pulse_needed = true; 1733 stop_clock(udc); 1734 DBG(DBG_BUS, "Suspend detected\n"); 1735 if (udc->gadget.speed != USB_SPEED_UNKNOWN 1736 && udc->driver && udc->driver->suspend) { 1737 spin_unlock(&udc->lock); 1738 udc->driver->suspend(&udc->gadget); 1739 spin_lock(&udc->lock); 1740 } 1741 } 1742 1743 if (status & USBA_WAKE_UP) { 1744 start_clock(udc); 1745 toggle_bias(udc, 1); 1746 usba_writel(udc, INT_CLR, USBA_WAKE_UP); 1747 DBG(DBG_BUS, "Wake Up CPU detected\n"); 1748 } 1749 1750 if (status & USBA_END_OF_RESUME) { 1751 udc->suspended = false; 1752 usba_writel(udc, INT_CLR, USBA_END_OF_RESUME); 1753 usba_int_enb_clear(udc, USBA_WAKE_UP); 1754 usba_int_enb_set(udc, USBA_DET_SUSPEND); 1755 generate_bias_pulse(udc); 1756 DBG(DBG_BUS, "Resume detected\n"); 1757 if (udc->gadget.speed != USB_SPEED_UNKNOWN 1758 && udc->driver && udc->driver->resume) { 1759 spin_unlock(&udc->lock); 1760 udc->driver->resume(&udc->gadget); 1761 spin_lock(&udc->lock); 1762 } 1763 } 1764 1765 dma_status = USBA_BFEXT(DMA_INT, status); 1766 if (dma_status) { 1767 int i; 1768 1769 usba_int_enb_set(udc, USBA_DET_SUSPEND); 1770 1771 for (i = 1; i <= USBA_NR_DMAS; i++) 1772 if (dma_status & (1 << i)) 1773 usba_dma_irq(udc, &udc->usba_ep[i]); 1774 } 1775 1776 ep_status = USBA_BFEXT(EPT_INT, status); 1777 if (ep_status) { 1778 int i; 1779 1780 usba_int_enb_set(udc, USBA_DET_SUSPEND); 1781 1782 for (i = 0; i < udc->num_ep; i++) 1783 if (ep_status & (1 << i)) { 1784 if (ep_is_control(&udc->usba_ep[i])) 1785 usba_control_irq(udc, &udc->usba_ep[i]); 1786 else 1787 usba_ep_irq(udc, &udc->usba_ep[i]); 1788 } 1789 } 1790 1791 if (status & USBA_END_OF_RESET) { 1792 struct usba_ep *ep0, *ep; 1793 int i, n; 1794 1795 usba_writel(udc, INT_CLR, 1796 USBA_END_OF_RESET|USBA_END_OF_RESUME 1797 |USBA_DET_SUSPEND|USBA_WAKE_UP); 1798 generate_bias_pulse(udc); 1799 reset_all_endpoints(udc); 1800 1801 if (udc->gadget.speed != USB_SPEED_UNKNOWN && udc->driver) { 1802 udc->gadget.speed = USB_SPEED_UNKNOWN; 1803 spin_unlock(&udc->lock); 1804 usb_gadget_udc_reset(&udc->gadget, udc->driver); 1805 spin_lock(&udc->lock); 1806 } 1807 1808 if (status & USBA_HIGH_SPEED) 1809 udc->gadget.speed = USB_SPEED_HIGH; 1810 else 1811 udc->gadget.speed = USB_SPEED_FULL; 1812 DBG(DBG_BUS, "%s bus reset detected\n", 1813 usb_speed_string(udc->gadget.speed)); 1814 1815 ep0 = &udc->usba_ep[0]; 1816 ep0->ep.desc = &usba_ep0_desc; 1817 ep0->state = WAIT_FOR_SETUP; 1818 usba_ep_writel(ep0, CFG, 1819 (USBA_BF(EPT_SIZE, EP0_EPT_SIZE) 1820 | USBA_BF(EPT_TYPE, USBA_EPT_TYPE_CONTROL) 1821 | USBA_BF(BK_NUMBER, USBA_BK_NUMBER_ONE))); 1822 usba_ep_writel(ep0, CTL_ENB, 1823 USBA_EPT_ENABLE | USBA_RX_SETUP); 1824 1825 /* If we get reset while suspended... */ 1826 udc->suspended = false; 1827 usba_int_enb_clear(udc, USBA_WAKE_UP); 1828 1829 usba_int_enb_set(udc, USBA_BF(EPT_INT, 1) | 1830 USBA_DET_SUSPEND | USBA_END_OF_RESUME); 1831 1832 /* 1833 * Unclear why we hit this irregularly, e.g. in usbtest, 1834 * but it's clearly harmless... 1835 */ 1836 if (!(usba_ep_readl(ep0, CFG) & USBA_EPT_MAPPED)) 1837 dev_err(&udc->pdev->dev, 1838 "ODD: EP0 configuration is invalid!\n"); 1839 1840 /* Preallocate other endpoints */ 1841 n = fifo_mode ? udc->num_ep : udc->configured_ep; 1842 for (i = 1; i < n; i++) { 1843 ep = &udc->usba_ep[i]; 1844 usba_ep_writel(ep, CFG, ep->ept_cfg); 1845 if (!(usba_ep_readl(ep, CFG) & USBA_EPT_MAPPED)) 1846 dev_err(&udc->pdev->dev, 1847 "ODD: EP%d configuration is invalid!\n", i); 1848 } 1849 } 1850 1851 spin_unlock(&udc->lock); 1852 1853 return IRQ_HANDLED; 1854 } 1855 1856 static int start_clock(struct usba_udc *udc) 1857 { 1858 int ret; 1859 1860 if (udc->clocked) 1861 return 0; 1862 1863 pm_stay_awake(&udc->pdev->dev); 1864 1865 ret = clk_prepare_enable(udc->pclk); 1866 if (ret) 1867 return ret; 1868 ret = clk_prepare_enable(udc->hclk); 1869 if (ret) { 1870 clk_disable_unprepare(udc->pclk); 1871 return ret; 1872 } 1873 1874 udc->clocked = true; 1875 return 0; 1876 } 1877 1878 static void stop_clock(struct usba_udc *udc) 1879 { 1880 if (!udc->clocked) 1881 return; 1882 1883 clk_disable_unprepare(udc->hclk); 1884 clk_disable_unprepare(udc->pclk); 1885 1886 udc->clocked = false; 1887 1888 pm_relax(&udc->pdev->dev); 1889 } 1890 1891 static int usba_start(struct usba_udc *udc) 1892 { 1893 unsigned long flags; 1894 int ret; 1895 1896 ret = start_clock(udc); 1897 if (ret) 1898 return ret; 1899 1900 if (udc->suspended) 1901 return 0; 1902 1903 spin_lock_irqsave(&udc->lock, flags); 1904 toggle_bias(udc, 1); 1905 usba_writel(udc, CTRL, USBA_ENABLE_MASK); 1906 /* Clear all requested and pending interrupts... */ 1907 usba_writel(udc, INT_ENB, 0); 1908 udc->int_enb_cache = 0; 1909 usba_writel(udc, INT_CLR, 1910 USBA_END_OF_RESET|USBA_END_OF_RESUME 1911 |USBA_DET_SUSPEND|USBA_WAKE_UP); 1912 /* ...and enable just 'reset' IRQ to get us started */ 1913 usba_int_enb_set(udc, USBA_END_OF_RESET); 1914 spin_unlock_irqrestore(&udc->lock, flags); 1915 1916 return 0; 1917 } 1918 1919 static void usba_stop(struct usba_udc *udc) 1920 { 1921 unsigned long flags; 1922 1923 if (udc->suspended) 1924 return; 1925 1926 spin_lock_irqsave(&udc->lock, flags); 1927 udc->gadget.speed = USB_SPEED_UNKNOWN; 1928 reset_all_endpoints(udc); 1929 1930 /* This will also disable the DP pullup */ 1931 toggle_bias(udc, 0); 1932 usba_writel(udc, CTRL, USBA_DISABLE_MASK); 1933 spin_unlock_irqrestore(&udc->lock, flags); 1934 1935 stop_clock(udc); 1936 } 1937 1938 static irqreturn_t usba_vbus_irq_thread(int irq, void *devid) 1939 { 1940 struct usba_udc *udc = devid; 1941 int vbus; 1942 1943 /* debounce */ 1944 udelay(10); 1945 1946 mutex_lock(&udc->vbus_mutex); 1947 1948 vbus = vbus_is_present(udc); 1949 if (vbus != udc->vbus_prev) { 1950 if (vbus) { 1951 usba_start(udc); 1952 } else { 1953 udc->suspended = false; 1954 usba_stop(udc); 1955 1956 if (udc->driver->disconnect) 1957 udc->driver->disconnect(&udc->gadget); 1958 } 1959 udc->vbus_prev = vbus; 1960 } 1961 1962 mutex_unlock(&udc->vbus_mutex); 1963 return IRQ_HANDLED; 1964 } 1965 1966 static int atmel_usba_start(struct usb_gadget *gadget, 1967 struct usb_gadget_driver *driver) 1968 { 1969 int ret; 1970 struct usba_udc *udc = container_of(gadget, struct usba_udc, gadget); 1971 unsigned long flags; 1972 1973 spin_lock_irqsave(&udc->lock, flags); 1974 udc->devstatus = 1 << USB_DEVICE_SELF_POWERED; 1975 udc->driver = driver; 1976 spin_unlock_irqrestore(&udc->lock, flags); 1977 1978 mutex_lock(&udc->vbus_mutex); 1979 1980 if (udc->vbus_pin) 1981 enable_irq(gpiod_to_irq(udc->vbus_pin)); 1982 1983 /* If Vbus is present, enable the controller and wait for reset */ 1984 udc->vbus_prev = vbus_is_present(udc); 1985 if (udc->vbus_prev) { 1986 ret = usba_start(udc); 1987 if (ret) 1988 goto err; 1989 } 1990 1991 mutex_unlock(&udc->vbus_mutex); 1992 return 0; 1993 1994 err: 1995 if (udc->vbus_pin) 1996 disable_irq(gpiod_to_irq(udc->vbus_pin)); 1997 1998 mutex_unlock(&udc->vbus_mutex); 1999 2000 spin_lock_irqsave(&udc->lock, flags); 2001 udc->devstatus &= ~(1 << USB_DEVICE_SELF_POWERED); 2002 udc->driver = NULL; 2003 spin_unlock_irqrestore(&udc->lock, flags); 2004 return ret; 2005 } 2006 2007 static int atmel_usba_stop(struct usb_gadget *gadget) 2008 { 2009 struct usba_udc *udc = container_of(gadget, struct usba_udc, gadget); 2010 2011 if (udc->vbus_pin) 2012 disable_irq(gpiod_to_irq(udc->vbus_pin)); 2013 2014 if (fifo_mode == 0) 2015 udc->configured_ep = 1; 2016 2017 udc->suspended = false; 2018 usba_stop(udc); 2019 2020 udc->driver = NULL; 2021 2022 return 0; 2023 } 2024 2025 static void at91sam9rl_toggle_bias(struct usba_udc *udc, int is_on) 2026 { 2027 regmap_update_bits(udc->pmc, AT91_CKGR_UCKR, AT91_PMC_BIASEN, 2028 is_on ? AT91_PMC_BIASEN : 0); 2029 } 2030 2031 static void at91sam9g45_pulse_bias(struct usba_udc *udc) 2032 { 2033 regmap_update_bits(udc->pmc, AT91_CKGR_UCKR, AT91_PMC_BIASEN, 0); 2034 regmap_update_bits(udc->pmc, AT91_CKGR_UCKR, AT91_PMC_BIASEN, 2035 AT91_PMC_BIASEN); 2036 } 2037 2038 static const struct usba_udc_errata at91sam9rl_errata = { 2039 .toggle_bias = at91sam9rl_toggle_bias, 2040 }; 2041 2042 static const struct usba_udc_errata at91sam9g45_errata = { 2043 .pulse_bias = at91sam9g45_pulse_bias, 2044 }; 2045 2046 static const struct of_device_id atmel_udc_dt_ids[] = { 2047 { .compatible = "atmel,at91sam9rl-udc", .data = &at91sam9rl_errata }, 2048 { .compatible = "atmel,at91sam9g45-udc", .data = &at91sam9g45_errata }, 2049 { .compatible = "atmel,sama5d3-udc" }, 2050 { /* sentinel */ } 2051 }; 2052 2053 MODULE_DEVICE_TABLE(of, atmel_udc_dt_ids); 2054 2055 static struct usba_ep * atmel_udc_of_init(struct platform_device *pdev, 2056 struct usba_udc *udc) 2057 { 2058 u32 val; 2059 struct device_node *np = pdev->dev.of_node; 2060 const struct of_device_id *match; 2061 struct device_node *pp; 2062 int i, ret; 2063 struct usba_ep *eps, *ep; 2064 2065 match = of_match_node(atmel_udc_dt_ids, np); 2066 if (!match) 2067 return ERR_PTR(-EINVAL); 2068 2069 udc->errata = match->data; 2070 udc->pmc = syscon_regmap_lookup_by_compatible("atmel,at91sam9g45-pmc"); 2071 if (IS_ERR(udc->pmc)) 2072 udc->pmc = syscon_regmap_lookup_by_compatible("atmel,at91sam9rl-pmc"); 2073 if (IS_ERR(udc->pmc)) 2074 udc->pmc = syscon_regmap_lookup_by_compatible("atmel,at91sam9x5-pmc"); 2075 if (udc->errata && IS_ERR(udc->pmc)) 2076 return ERR_CAST(udc->pmc); 2077 2078 udc->num_ep = 0; 2079 2080 udc->vbus_pin = devm_gpiod_get_optional(&pdev->dev, "atmel,vbus", 2081 GPIOD_IN); 2082 2083 if (fifo_mode == 0) { 2084 pp = NULL; 2085 while ((pp = of_get_next_child(np, pp))) 2086 udc->num_ep++; 2087 udc->configured_ep = 1; 2088 } else { 2089 udc->num_ep = usba_config_fifo_table(udc); 2090 } 2091 2092 eps = devm_kcalloc(&pdev->dev, udc->num_ep, sizeof(struct usba_ep), 2093 GFP_KERNEL); 2094 if (!eps) 2095 return ERR_PTR(-ENOMEM); 2096 2097 udc->gadget.ep0 = &eps[0].ep; 2098 2099 INIT_LIST_HEAD(&eps[0].ep.ep_list); 2100 2101 pp = NULL; 2102 i = 0; 2103 while ((pp = of_get_next_child(np, pp)) && i < udc->num_ep) { 2104 ep = &eps[i]; 2105 2106 ret = of_property_read_u32(pp, "reg", &val); 2107 if (ret) { 2108 dev_err(&pdev->dev, "of_probe: reg error(%d)\n", ret); 2109 goto err; 2110 } 2111 ep->index = fifo_mode ? udc->fifo_cfg[i].hw_ep_num : val; 2112 2113 ret = of_property_read_u32(pp, "atmel,fifo-size", &val); 2114 if (ret) { 2115 dev_err(&pdev->dev, "of_probe: fifo-size error(%d)\n", ret); 2116 goto err; 2117 } 2118 if (fifo_mode) { 2119 if (val < udc->fifo_cfg[i].fifo_size) { 2120 dev_warn(&pdev->dev, 2121 "Using max fifo-size value from DT\n"); 2122 ep->fifo_size = val; 2123 } else { 2124 ep->fifo_size = udc->fifo_cfg[i].fifo_size; 2125 } 2126 } else { 2127 ep->fifo_size = val; 2128 } 2129 2130 ret = of_property_read_u32(pp, "atmel,nb-banks", &val); 2131 if (ret) { 2132 dev_err(&pdev->dev, "of_probe: nb-banks error(%d)\n", ret); 2133 goto err; 2134 } 2135 if (fifo_mode) { 2136 if (val < udc->fifo_cfg[i].nr_banks) { 2137 dev_warn(&pdev->dev, 2138 "Using max nb-banks value from DT\n"); 2139 ep->nr_banks = val; 2140 } else { 2141 ep->nr_banks = udc->fifo_cfg[i].nr_banks; 2142 } 2143 } else { 2144 ep->nr_banks = val; 2145 } 2146 2147 ep->can_dma = of_property_read_bool(pp, "atmel,can-dma"); 2148 ep->can_isoc = of_property_read_bool(pp, "atmel,can-isoc"); 2149 2150 sprintf(ep->name, "ep%d", ep->index); 2151 ep->ep.name = ep->name; 2152 2153 ep->ep_regs = udc->regs + USBA_EPT_BASE(i); 2154 ep->dma_regs = udc->regs + USBA_DMA_BASE(i); 2155 ep->fifo = udc->fifo + USBA_FIFO_BASE(i); 2156 ep->ep.ops = &usba_ep_ops; 2157 usb_ep_set_maxpacket_limit(&ep->ep, ep->fifo_size); 2158 ep->udc = udc; 2159 INIT_LIST_HEAD(&ep->queue); 2160 2161 if (ep->index == 0) { 2162 ep->ep.caps.type_control = true; 2163 } else { 2164 ep->ep.caps.type_iso = ep->can_isoc; 2165 ep->ep.caps.type_bulk = true; 2166 ep->ep.caps.type_int = true; 2167 } 2168 2169 ep->ep.caps.dir_in = true; 2170 ep->ep.caps.dir_out = true; 2171 2172 if (fifo_mode != 0) { 2173 /* 2174 * Generate ept_cfg based on FIFO size and 2175 * banks number 2176 */ 2177 if (ep->fifo_size <= 8) 2178 ep->ept_cfg = USBA_BF(EPT_SIZE, USBA_EPT_SIZE_8); 2179 else 2180 /* LSB is bit 1, not 0 */ 2181 ep->ept_cfg = 2182 USBA_BF(EPT_SIZE, fls(ep->fifo_size - 1) - 3); 2183 2184 ep->ept_cfg |= USBA_BF(BK_NUMBER, ep->nr_banks); 2185 } 2186 2187 if (i) 2188 list_add_tail(&ep->ep.ep_list, &udc->gadget.ep_list); 2189 2190 i++; 2191 } 2192 2193 if (i == 0) { 2194 dev_err(&pdev->dev, "of_probe: no endpoint specified\n"); 2195 ret = -EINVAL; 2196 goto err; 2197 } 2198 2199 return eps; 2200 err: 2201 return ERR_PTR(ret); 2202 } 2203 2204 static int usba_udc_probe(struct platform_device *pdev) 2205 { 2206 struct resource *res; 2207 struct clk *pclk, *hclk; 2208 struct usba_udc *udc; 2209 int irq, ret, i; 2210 2211 udc = devm_kzalloc(&pdev->dev, sizeof(*udc), GFP_KERNEL); 2212 if (!udc) 2213 return -ENOMEM; 2214 2215 udc->gadget = usba_gadget_template; 2216 INIT_LIST_HEAD(&udc->gadget.ep_list); 2217 2218 res = platform_get_resource(pdev, IORESOURCE_MEM, CTRL_IOMEM_ID); 2219 udc->regs = devm_ioremap_resource(&pdev->dev, res); 2220 if (IS_ERR(udc->regs)) 2221 return PTR_ERR(udc->regs); 2222 dev_info(&pdev->dev, "MMIO registers at %pR mapped at %p\n", 2223 res, udc->regs); 2224 2225 res = platform_get_resource(pdev, IORESOURCE_MEM, FIFO_IOMEM_ID); 2226 udc->fifo = devm_ioremap_resource(&pdev->dev, res); 2227 if (IS_ERR(udc->fifo)) 2228 return PTR_ERR(udc->fifo); 2229 dev_info(&pdev->dev, "FIFO at %pR mapped at %p\n", res, udc->fifo); 2230 2231 irq = platform_get_irq(pdev, 0); 2232 if (irq < 0) 2233 return irq; 2234 2235 pclk = devm_clk_get(&pdev->dev, "pclk"); 2236 if (IS_ERR(pclk)) 2237 return PTR_ERR(pclk); 2238 hclk = devm_clk_get(&pdev->dev, "hclk"); 2239 if (IS_ERR(hclk)) 2240 return PTR_ERR(hclk); 2241 2242 spin_lock_init(&udc->lock); 2243 mutex_init(&udc->vbus_mutex); 2244 udc->pdev = pdev; 2245 udc->pclk = pclk; 2246 udc->hclk = hclk; 2247 2248 platform_set_drvdata(pdev, udc); 2249 2250 /* Make sure we start from a clean slate */ 2251 ret = clk_prepare_enable(pclk); 2252 if (ret) { 2253 dev_err(&pdev->dev, "Unable to enable pclk, aborting.\n"); 2254 return ret; 2255 } 2256 2257 usba_writel(udc, CTRL, USBA_DISABLE_MASK); 2258 clk_disable_unprepare(pclk); 2259 2260 udc->usba_ep = atmel_udc_of_init(pdev, udc); 2261 2262 toggle_bias(udc, 0); 2263 2264 if (IS_ERR(udc->usba_ep)) 2265 return PTR_ERR(udc->usba_ep); 2266 2267 ret = devm_request_irq(&pdev->dev, irq, usba_udc_irq, 0, 2268 "atmel_usba_udc", udc); 2269 if (ret) { 2270 dev_err(&pdev->dev, "Cannot request irq %d (error %d)\n", 2271 irq, ret); 2272 return ret; 2273 } 2274 udc->irq = irq; 2275 2276 if (udc->vbus_pin) { 2277 irq_set_status_flags(gpiod_to_irq(udc->vbus_pin), IRQ_NOAUTOEN); 2278 ret = devm_request_threaded_irq(&pdev->dev, 2279 gpiod_to_irq(udc->vbus_pin), NULL, 2280 usba_vbus_irq_thread, USBA_VBUS_IRQFLAGS, 2281 "atmel_usba_udc", udc); 2282 if (ret) { 2283 udc->vbus_pin = NULL; 2284 dev_warn(&udc->pdev->dev, 2285 "failed to request vbus irq; " 2286 "assuming always on\n"); 2287 } 2288 } 2289 2290 ret = usb_add_gadget_udc(&pdev->dev, &udc->gadget); 2291 if (ret) 2292 return ret; 2293 device_init_wakeup(&pdev->dev, 1); 2294 2295 usba_init_debugfs(udc); 2296 for (i = 1; i < udc->num_ep; i++) 2297 usba_ep_init_debugfs(udc, &udc->usba_ep[i]); 2298 2299 return 0; 2300 } 2301 2302 static int usba_udc_remove(struct platform_device *pdev) 2303 { 2304 struct usba_udc *udc; 2305 int i; 2306 2307 udc = platform_get_drvdata(pdev); 2308 2309 device_init_wakeup(&pdev->dev, 0); 2310 usb_del_gadget_udc(&udc->gadget); 2311 2312 for (i = 1; i < udc->num_ep; i++) 2313 usba_ep_cleanup_debugfs(&udc->usba_ep[i]); 2314 usba_cleanup_debugfs(udc); 2315 2316 return 0; 2317 } 2318 2319 #ifdef CONFIG_PM_SLEEP 2320 static int usba_udc_suspend(struct device *dev) 2321 { 2322 struct usba_udc *udc = dev_get_drvdata(dev); 2323 2324 /* Not started */ 2325 if (!udc->driver) 2326 return 0; 2327 2328 mutex_lock(&udc->vbus_mutex); 2329 2330 if (!device_may_wakeup(dev)) { 2331 udc->suspended = false; 2332 usba_stop(udc); 2333 goto out; 2334 } 2335 2336 /* 2337 * Device may wake up. We stay clocked if we failed 2338 * to request vbus irq, assuming always on. 2339 */ 2340 if (udc->vbus_pin) { 2341 /* FIXME: right to stop here...??? */ 2342 usba_stop(udc); 2343 enable_irq_wake(gpiod_to_irq(udc->vbus_pin)); 2344 } 2345 2346 enable_irq_wake(udc->irq); 2347 2348 out: 2349 mutex_unlock(&udc->vbus_mutex); 2350 return 0; 2351 } 2352 2353 static int usba_udc_resume(struct device *dev) 2354 { 2355 struct usba_udc *udc = dev_get_drvdata(dev); 2356 2357 /* Not started */ 2358 if (!udc->driver) 2359 return 0; 2360 2361 if (device_may_wakeup(dev)) { 2362 if (udc->vbus_pin) 2363 disable_irq_wake(gpiod_to_irq(udc->vbus_pin)); 2364 2365 disable_irq_wake(udc->irq); 2366 } 2367 2368 /* If Vbus is present, enable the controller and wait for reset */ 2369 mutex_lock(&udc->vbus_mutex); 2370 udc->vbus_prev = vbus_is_present(udc); 2371 if (udc->vbus_prev) 2372 usba_start(udc); 2373 mutex_unlock(&udc->vbus_mutex); 2374 2375 return 0; 2376 } 2377 #endif 2378 2379 static SIMPLE_DEV_PM_OPS(usba_udc_pm_ops, usba_udc_suspend, usba_udc_resume); 2380 2381 static struct platform_driver udc_driver = { 2382 .remove = usba_udc_remove, 2383 .driver = { 2384 .name = "atmel_usba_udc", 2385 .pm = &usba_udc_pm_ops, 2386 .of_match_table = atmel_udc_dt_ids, 2387 }, 2388 }; 2389 2390 module_platform_driver_probe(udc_driver, usba_udc_probe); 2391 2392 MODULE_DESCRIPTION("Atmel USBA UDC driver"); 2393 MODULE_AUTHOR("Haavard Skinnemoen (Atmel)"); 2394 MODULE_LICENSE("GPL"); 2395 MODULE_ALIAS("platform:atmel_usba_udc"); 2396