xref: /openbmc/linux/drivers/usb/gadget/Kconfig (revision 8443f2d2)

#
# USB Gadget support on a system involves
#    (a) a peripheral controller, and
#    (b) the gadget driver using it.
#
# NOTE:  Gadget support ** DOES NOT ** depend on host-side CONFIG_USB !!
#
#  - Host systems (like PCs) need CONFIG_USB (with "A" jacks).
#  - Peripherals (like PDAs) need CONFIG_USB_GADGET (with "B" jacks).
#  - Some systems have both kinds of controllers.
#
# With help from a special transceiver and a "Mini-AB" jack, systems with
# both kinds of controller can also support "USB On-the-Go" (CONFIG_USB_OTG).
#

menuconfig USB_GADGET
	tristate "USB Gadget Support"
	select NLS
	help
	   USB is a master/slave protocol, organized with one master
	   host (such as a PC) controlling up to 127 peripheral devices.
	   The USB hardware is asymmetric, which makes it easier to set up:
	   you can't connect a "to-the-host" connector to a peripheral.

	   Linux can run in the host, or in the peripheral.  In both cases
	   you need a low level bus controller driver, and some software
	   talking to it.  Peripheral controllers are often discrete silicon,
	   or are integrated with the CPU in a microcontroller.  The more
	   familiar host side controllers have names like "EHCI", "OHCI",
	   or "UHCI", and are usually integrated into southbridges on PC
	   motherboards.

	   Enable this configuration option if you want to run Linux inside
	   a USB peripheral device.  Configure one hardware driver for your
	   peripheral/device side bus controller, and a "gadget driver" for
	   your peripheral protocol.  (If you use modular gadget drivers,
	   you may configure more than one.)

	   If in doubt, say "N" and don't enable these drivers; most people
	   don't have this kind of hardware (except maybe inside Linux PDAs).

	   For more information, see <http://www.linux-usb.org/gadget> and
	   the kernel DocBook documentation for this API.

if USB_GADGET

config USB_GADGET_DEBUG
	boolean "Debugging messages (DEVELOPMENT)"
	depends on DEBUG_KERNEL
	help
	   Many controller and gadget drivers will print some debugging
	   messages if you use this option to ask for those messages.

	   Avoid enabling these messages, even if you're actively
	   debugging such a driver.  Many drivers will emit so many
	   messages that the driver timings are affected, which will
	   either create new failure modes or remove the one you're
	   trying to track down.  Never enable these messages for a
	   production build.

config USB_GADGET_VERBOSE
	bool "Verbose debugging Messages (DEVELOPMENT)"
	depends on USB_GADGET_DEBUG
	help
	   Many controller and gadget drivers will print verbose debugging
	   messages if you use this option to ask for those messages.

	   Avoid enabling these messages, even if you're actively
	   debugging such a driver.  Many drivers will emit so many
	   messages that the driver timings are affected, which will
	   either create new failure modes or remove the one you're
	   trying to track down.  Never enable these messages for a
	   production build.

config USB_GADGET_DEBUG_FILES
	boolean "Debugging information files (DEVELOPMENT)"
	depends on PROC_FS
	help
	   Some of the drivers in the "gadget" framework can expose
	   debugging information in files such as /proc/driver/udc
	   (for a peripheral controller).  The information in these
	   files may help when you're troubleshooting or bringing up a
	   driver on a new board.   Enable these files by choosing "Y"
	   here.  If in doubt, or to conserve kernel memory, say "N".

config USB_GADGET_DEBUG_FS
	boolean "Debugging information files in debugfs (DEVELOPMENT)"
	depends on DEBUG_FS
	help
	   Some of the drivers in the "gadget" framework can expose
	   debugging information in files under /sys/kernel/debug/.
	   The information in these files may help when you're
	   troubleshooting or bringing up a driver on a new board.
	   Enable these files by choosing "Y" here.  If in doubt, or
	   to conserve kernel memory, say "N".

config USB_GADGET_VBUS_DRAW
	int "Maximum VBUS Power usage (2-500 mA)"
	range 2 500
	default 2
	help
	   Some devices need to draw power from USB when they are
	   configured, perhaps to operate circuitry or to recharge
	   batteries.  This is in addition to any local power supply,
	   such as an AC adapter or batteries.

	   Enter the maximum power your device draws through USB, in
	   milliAmperes.  The permitted range of values is 2 - 500 mA;
	   0 mA would be legal, but can make some hosts misbehave.

	   This value will be used except for system-specific gadget
	   drivers that have more specific information.

config USB_GADGET_STORAGE_NUM_BUFFERS
	int "Number of storage pipeline buffers"
	range 2 4
	default 2
	help
	   Usually 2 buffers are enough to establish a good buffering
	   pipeline. The number may be increased in order to compensate
	   for a bursty VFS behaviour. For instance there may be CPU wake up
	   latencies that makes the VFS to appear bursty in a system with
	   an CPU on-demand governor. Especially if DMA is doing IO to
	   offload the CPU. In this case the CPU will go into power
	   save often and spin up occasionally to move data within VFS.
	   If selecting USB_GADGET_DEBUG_FILES this value may be set by
	   a module parameter as well.
	   If unsure, say 2.

#
# USB Peripheral Controller Support
#
# The order here is alphabetical, except that integrated controllers go
# before discrete ones so they will be the initial/default value:
#   - integrated/SOC controllers first
#   - licensed IP used in both SOC and discrete versions
#   - discrete ones (including all PCI-only controllers)
#   - debug/dummy gadget+hcd is last.
#
menu "USB Peripheral Controller"

#
# Integrated controllers
#

config USB_AT91
	tristate "Atmel AT91 USB Device Port"
	depends on ARCH_AT91
	help
	   Many Atmel AT91 processors (such as the AT91RM2000) have a
	   full speed USB Device Port with support for five configurable
	   endpoints (plus endpoint zero).

	   Say "y" to link the driver statically, or "m" to build a
	   dynamically linked module called "at91_udc" and force all
	   gadget drivers to also be dynamically linked.

config USB_LPC32XX
	tristate "LPC32XX USB Peripheral Controller"
	depends on ARCH_LPC32XX && I2C
	select USB_ISP1301
	help
	   This option selects the USB device controller in the LPC32xx SoC.

	   Say "y" to link the driver statically, or "m" to build a
	   dynamically linked module called "lpc32xx_udc" and force all
	   gadget drivers to also be dynamically linked.

config USB_ATMEL_USBA
	tristate "Atmel USBA"
	depends on AVR32 || ARCH_AT91
	help
	  USBA is the integrated high-speed USB Device controller on
	  the AT32AP700x, some AT91SAM9 and AT91CAP9 processors from Atmel.

config USB_BCM63XX_UDC
	tristate "Broadcom BCM63xx Peripheral Controller"
	depends on BCM63XX
	help
	   Many Broadcom BCM63xx chipsets (such as the BCM6328) have a
	   high speed USB Device Port with support for four fixed endpoints
	   (plus endpoint zero).

	   Say "y" to link the driver statically, or "m" to build a
	   dynamically linked module called "bcm63xx_udc".

config USB_FSL_USB2
	tristate "Freescale Highspeed USB DR Peripheral Controller"
	depends on FSL_SOC || ARCH_MXC
	select USB_FSL_MPH_DR_OF if OF
	help
	   Some of Freescale PowerPC and i.MX processors have a High Speed
	   Dual-Role(DR) USB controller, which supports device mode.

	   The number of programmable endpoints is different through
	   SOC revisions.

	   Say "y" to link the driver statically, or "m" to build a
	   dynamically linked module called "fsl_usb2_udc" and force
	   all gadget drivers to also be dynamically linked.

config USB_FUSB300
	tristate "Faraday FUSB300 USB Peripheral Controller"
	depends on !PHYS_ADDR_T_64BIT && HAS_DMA
	help
	   Faraday usb device controller FUSB300 driver

config USB_FOTG210_UDC
	depends on HAS_DMA
	tristate "Faraday FOTG210 USB Peripheral Controller"
	help
	   Faraday USB2.0 OTG controller which can be configured as
	   high speed or full speed USB device. This driver supppors
	   Bulk Transfer so far.

	   Say "y" to link the driver statically, or "m" to build a
	   dynamically linked module called "fotg210_udc".

config USB_GR_UDC
       tristate "Aeroflex Gaisler GRUSBDC USB Peripheral Controller Driver"
       depends on HAS_DMA
       help
          Select this to support Aeroflex Gaisler GRUSBDC cores from the GRLIB
	  VHDL IP core library.

config USB_OMAP
	tristate "OMAP USB Device Controller"
	depends on ARCH_OMAP1
	depends on ISP1301_OMAP || !(MACH_OMAP_H2 || MACH_OMAP_H3)
	help
	   Many Texas Instruments OMAP processors have flexible full
	   speed USB device controllers, with support for up to 30
	   endpoints (plus endpoint zero).  This driver supports the
	   controller in the OMAP 1611, and should work with controllers
	   in other OMAP processors too, given minor tweaks.

	   Say "y" to link the driver statically, or "m" to build a
	   dynamically linked module called "omap_udc" and force all
	   gadget drivers to also be dynamically linked.

config USB_PXA25X
	tristate "PXA 25x or IXP 4xx"
	depends on (ARCH_PXA && PXA25x) || ARCH_IXP4XX
	help
	   Intel's PXA 25x series XScale ARM-5TE processors include
	   an integrated full speed USB 1.1 device controller.  The
	   controller in the IXP 4xx series is register-compatible.

	   It has fifteen fixed-function endpoints, as well as endpoint
	   zero (for control transfers).

	   Say "y" to link the driver statically, or "m" to build a
	   dynamically linked module called "pxa25x_udc" and force all
	   gadget drivers to also be dynamically linked.

# if there's only one gadget driver, using only two bulk endpoints,
# don't waste memory for the other endpoints
config USB_PXA25X_SMALL
	depends on USB_PXA25X
	bool
	default n if USB_ETH_RNDIS
	default y if USB_ZERO
	default y if USB_ETH
	default y if USB_G_SERIAL

config USB_R8A66597
	tristate "Renesas R8A66597 USB Peripheral Controller"
	depends on HAS_DMA
	help
	   R8A66597 is a discrete USB host and peripheral controller chip that
	   supports both full and high speed USB 2.0 data transfers.
	   It has nine configurable endpoints, and endpoint zero.

	   Say "y" to link the driver statically, or "m" to build a
	   dynamically linked module called "r8a66597_udc" and force all
	   gadget drivers to also be dynamically linked.

config USB_RENESAS_USBHS_UDC
	tristate 'Renesas USBHS controller'
	depends on USB_RENESAS_USBHS
	help
	   Renesas USBHS is a discrete USB host and peripheral controller chip
	   that supports both full and high speed USB 2.0 data transfers.
	   It has nine or more configurable endpoints, and endpoint zero.

	   Say "y" to link the driver statically, or "m" to build a
	   dynamically linked module called "renesas_usbhs" and force all
	   gadget drivers to also be dynamically linked.

config USB_PXA27X
	tristate "PXA 27x"
	help
	   Intel's PXA 27x series XScale ARM v5TE processors include
	   an integrated full speed USB 1.1 device controller.

	   It has up to 23 endpoints, as well as endpoint zero (for
	   control transfers).

	   Say "y" to link the driver statically, or "m" to build a
	   dynamically linked module called "pxa27x_udc" and force all
	   gadget drivers to also be dynamically linked.

config USB_S3C2410
	tristate "S3C2410 USB Device Controller"
	depends on ARCH_S3C24XX
	help
	  Samsung's S3C2410 is an ARM-4 processor with an integrated
	  full speed USB 1.1 device controller.  It has 4 configurable
	  endpoints, as well as endpoint zero (for control transfers).

	  This driver has been tested on the S3C2410, S3C2412, and
	  S3C2440 processors.

config USB_S3C2410_DEBUG
	boolean "S3C2410 udc debug messages"
	depends on USB_S3C2410

config USB_S3C_HSUDC
	tristate "S3C2416, S3C2443 and S3C2450 USB Device Controller"
	depends on ARCH_S3C24XX
	help
	  Samsung's S3C2416, S3C2443 and S3C2450 is an ARM9 based SoC
	  integrated with dual speed USB 2.0 device controller. It has
	  8 endpoints, as well as endpoint zero.

	  This driver has been tested on S3C2416 and S3C2450 processors.

config USB_MV_UDC
	tristate "Marvell USB2.0 Device Controller"
	depends on HAS_DMA
	help
	  Marvell Socs (including PXA and MMP series) include a high speed
	  USB2.0 OTG controller, which can be configured as high speed or
	  full speed USB peripheral.

config USB_MV_U3D
	depends on HAS_DMA
	tristate "MARVELL PXA2128 USB 3.0 controller"
	help
	  MARVELL PXA2128 Processor series include a super speed USB3.0 device
	  controller, which support super speed USB peripheral.

#
# Controllers available in both integrated and discrete versions
#

config USB_M66592
	tristate "Renesas M66592 USB Peripheral Controller"
	help
	   M66592 is a discrete USB peripheral controller chip that
	   supports both full and high speed USB 2.0 data transfers.
	   It has seven configurable endpoints, and endpoint zero.

	   Say "y" to link the driver statically, or "m" to build a
	   dynamically linked module called "m66592_udc" and force all
	   gadget drivers to also be dynamically linked.

#
# Controllers available only in discrete form (and all PCI controllers)
#

config USB_AMD5536UDC
	tristate "AMD5536 UDC"
	depends on PCI
	help
	   The AMD5536 UDC is part of the AMD Geode CS5536, an x86 southbridge.
	   It is a USB Highspeed DMA capable USB device controller. Beside ep0
	   it provides 4 IN and 4 OUT endpoints (bulk or interrupt type).
	   The UDC port supports OTG operation, and may be used as a host port
	   if it's not being used to implement peripheral or OTG roles.

	   Say "y" to link the driver statically, or "m" to build a
	   dynamically linked module called "amd5536udc" and force all
	   gadget drivers to also be dynamically linked.

config USB_FSL_QE
	tristate "Freescale QE/CPM USB Device Controller"
	depends on FSL_SOC && (QUICC_ENGINE || CPM)
	help
	   Some of Freescale PowerPC processors have a Full Speed
	   QE/CPM2 USB controller, which support device mode with 4
	   programmable endpoints. This driver supports the
	   controller in the MPC8360 and MPC8272, and should work with
	   controllers having QE or CPM2, given minor tweaks.

	   Set CONFIG_USB_GADGET to "m" to build this driver as a
	   dynamically linked module called "fsl_qe_udc".

config USB_NET2272
	tristate "PLX NET2272"
	help
	  PLX NET2272 is a USB peripheral controller which supports
	  both full and high speed USB 2.0 data transfers.

	  It has three configurable endpoints, as well as endpoint zero
	  (for control transfer).
	  Say "y" to link the driver statically, or "m" to build a
	  dynamically linked module called "net2272" and force all
	  gadget drivers to also be dynamically linked.

config USB_NET2272_DMA
	boolean "Support external DMA controller"
	depends on USB_NET2272 && HAS_DMA
	help
	  The NET2272 part can optionally support an external DMA
	  controller, but your board has to have support in the
	  driver itself.

	  If unsure, say "N" here.  The driver works fine in PIO mode.

config USB_NET2280
	tristate "NetChip 228x / PLX USB338x"
	depends on PCI
	help
	   NetChip 2280 / 2282 is a PCI based USB peripheral controller which
	   supports both full and high speed USB 2.0 data transfers.

	   It has six configurable endpoints, as well as endpoint zero
	   (for control transfers) and several endpoints with dedicated
	   functions.

	   PLX 3380 / 3382 is a PCIe based USB peripheral controller which
	   supports full, high speed USB 2.0 and super speed USB 3.0
	   data transfers.

	   It has eight configurable endpoints, as well as endpoint zero
	   (for control transfers) and several endpoints with dedicated
	   functions.

	   Say "y" to link the driver statically, or "m" to build a
	   dynamically linked module called "net2280" and force all
	   gadget drivers to also be dynamically linked.

config USB_GOKU
	tristate "Toshiba TC86C001 'Goku-S'"
	depends on PCI
	help
	   The Toshiba TC86C001 is a PCI device which includes controllers
	   for full speed USB devices, IDE, I2C, SIO, plus a USB host (OHCI).

	   The device controller has three configurable (bulk or interrupt)
	   endpoints, plus endpoint zero (for control transfers).

	   Say "y" to link the driver statically, or "m" to build a
	   dynamically linked module called "goku_udc" and to force all
	   gadget drivers to also be dynamically linked.

config USB_EG20T
	tristate "Intel EG20T PCH/LAPIS Semiconductor IOH(ML7213/ML7831) UDC"
	depends on PCI
	help
	  This is a USB device driver for EG20T PCH.
	  EG20T PCH is the platform controller hub that is used in Intel's
	  general embedded platform. EG20T PCH has USB device interface.
	  Using this interface, it is able to access system devices connected
	  to USB device.
	  This driver enables USB device function.
	  USB device is a USB peripheral controller which
	  supports both full and high speed USB 2.0 data transfers.
	  This driver supports both control transfer and bulk transfer modes.
	  This driver dose not support interrupt transfer or isochronous
	  transfer modes.

	  This driver also can be used for LAPIS Semiconductor's ML7213 which is
	  for IVI(In-Vehicle Infotainment) use.
	  ML7831 is for general purpose use.
	  ML7213/ML7831 is companion chip for Intel Atom E6xx series.
	  ML7213/ML7831 is completely compatible for Intel EG20T PCH.

#
# LAST -- dummy/emulated controller
#

config USB_DUMMY_HCD
	tristate "Dummy HCD (DEVELOPMENT)"
	depends on USB=y || (USB=m && USB_GADGET=m)
	help
	  This host controller driver emulates USB, looping all data transfer
	  requests back to a USB "gadget driver" in the same host.  The host
	  side is the master; the gadget side is the slave.  Gadget drivers
	  can be high, full, or low speed; and they have access to endpoints
	  like those from NET2280, PXA2xx, or SA1100 hardware.

	  This may help in some stages of creating a driver to embed in a
	  Linux device, since it lets you debug several parts of the gadget
	  driver without its hardware or drivers being involved.

	  Since such a gadget side driver needs to interoperate with a host
	  side Linux-USB device driver, this may help to debug both sides
	  of a USB protocol stack.

	  Say "y" to link the driver statically, or "m" to build a
	  dynamically linked module called "dummy_hcd" and force all
	  gadget drivers to also be dynamically linked.

# NOTE:  Please keep dummy_hcd LAST so that "real hardware" appears
# first and will be selected by default.

endmenu

#
# USB Gadget Drivers
#

# composite based drivers
config USB_LIBCOMPOSITE
	tristate
	select CONFIGFS_FS
	depends on USB_GADGET

config USB_F_ACM
	tristate

config USB_F_SS_LB
	tristate

config USB_U_SERIAL
	tristate

config USB_U_ETHER
	tristate

config USB_F_SERIAL
	tristate

config USB_F_OBEX
	tristate

config USB_F_NCM
	tristate

config USB_F_ECM
	tristate

config USB_F_PHONET
	tristate

config USB_F_EEM
	tristate

config USB_F_SUBSET
	tristate

config USB_F_RNDIS
	tristate

config USB_F_MASS_STORAGE
	tristate

config USB_F_FS
	tristate

choice
	tristate "USB Gadget Drivers"
	default USB_ETH
	help
	  A Linux "Gadget Driver" talks to the USB Peripheral Controller
	  driver through the abstract "gadget" API.  Some other operating
	  systems call these "client" drivers, of which "class drivers"
	  are a subset (implementing a USB device class specification).
	  A gadget driver implements one or more USB functions using
	  the peripheral hardware.

	  Gadget drivers are hardware-neutral, or "platform independent",
	  except that they sometimes must understand quirks or limitations
	  of the particular controllers they work with.  For example, when
	  a controller doesn't support alternate configurations or provide
	  enough of the right types of endpoints, the gadget driver might
	  not be able work with that controller, or might need to implement
	  a less common variant of a device class protocol.

# this first set of drivers all depend on bulk-capable hardware.

config USB_CONFIGFS
	tristate "USB functions configurable through configfs"
	select USB_LIBCOMPOSITE
	help
	  A Linux USB "gadget" can be set up through configfs.
	  If this is the case, the USB functions (which from the host's
	  perspective are seen as interfaces) and configurations are
	  specified simply by creating appropriate directories in configfs.
	  Associating functions with configurations is done by creating
	  appropriate symbolic links.
	  For more information see Documentation/usb/gadget_configfs.txt.

config USB_CONFIGFS_SERIAL
	boolean "Generic serial bulk in/out"
	depends on USB_CONFIGFS
	depends on TTY
	select USB_U_SERIAL
	select USB_F_SERIAL
	help
	  The function talks to the Linux-USB generic serial driver.

config USB_CONFIGFS_ACM
	boolean "Abstract Control Model (CDC ACM)"
	depends on USB_CONFIGFS
	depends on TTY
	select USB_U_SERIAL
	select USB_F_ACM
	help
	  ACM serial link.  This function can be used to interoperate with
	  MS-Windows hosts or with the Linux-USB "cdc-acm" driver.

config USB_CONFIGFS_OBEX
	boolean "Object Exchange Model (CDC OBEX)"
	depends on USB_CONFIGFS
	depends on TTY
	select USB_U_SERIAL
	select USB_F_OBEX
	help
	  You will need a user space OBEX server talking to /dev/ttyGS*,
	  since the kernel itself doesn't implement the OBEX protocol.

config USB_CONFIGFS_NCM
	boolean "Network Control Model (CDC NCM)"
	depends on USB_CONFIGFS
	depends on NET
	select USB_U_ETHER
	select USB_F_NCM
	help
	  NCM is an advanced protocol for Ethernet encapsulation, allows
	  grouping of several ethernet frames into one USB transfer and
	  different alignment possibilities.

config USB_CONFIGFS_ECM
	boolean "Ethernet Control Model (CDC ECM)"
	depends on USB_CONFIGFS
	depends on NET
	select USB_U_ETHER
	select USB_F_ECM
	help
	  The "Communication Device Class" (CDC) Ethernet Control Model.
	  That protocol is often avoided with pure Ethernet adapters, in
	  favor of simpler vendor-specific hardware, but is widely
	  supported by firmware for smart network devices.

config USB_CONFIGFS_ECM_SUBSET
	boolean "Ethernet Control Model (CDC ECM) subset"
	depends on USB_CONFIGFS
	depends on NET
	select USB_U_ETHER
	select USB_F_SUBSET
	help
	  On hardware that can't implement the full protocol,
	  a simple CDC subset is used, placing fewer demands on USB.

config USB_CONFIGFS_RNDIS
	bool "RNDIS"
	depends on USB_CONFIGFS
	depends on NET
	select USB_U_ETHER
	select USB_F_RNDIS
	help
	   Microsoft Windows XP bundles the "Remote NDIS" (RNDIS) protocol,
	   and Microsoft provides redistributable binary RNDIS drivers for
	   older versions of Windows.

	   To make MS-Windows work with this, use Documentation/usb/linux.inf
	   as the "driver info file".  For versions of MS-Windows older than
	   XP, you'll need to download drivers from Microsoft's website; a URL
	   is given in comments found in that info file.

config USB_CONFIGFS_EEM
	bool "Ethernet Emulation Model (EEM)"
	depends on USB_CONFIGFS
	depends on NET
	select USB_U_ETHER
	select USB_F_EEM
	help
	  CDC EEM is a newer USB standard that is somewhat simpler than CDC ECM
	  and therefore can be supported by more hardware.  Technically ECM and
	  EEM are designed for different applications.  The ECM model extends
	  the network interface to the target (e.g. a USB cable modem), and the
	  EEM model is for mobile devices to communicate with hosts using
	  ethernet over USB.  For Linux gadgets, however, the interface with
	  the host is the same (a usbX device), so the differences are minimal.

config USB_CONFIGFS_PHONET
	boolean "Phonet protocol"
	depends on USB_CONFIGFS
	depends on NET
	depends on PHONET
	select USB_U_ETHER
	select USB_F_PHONET
	help
	  The Phonet protocol implementation for USB device.

config USB_CONFIGFS_MASS_STORAGE
	boolean "Mass storage"
	depends on USB_CONFIGFS
	depends on BLOCK
	select USB_F_MASS_STORAGE
	help
	  The Mass Storage Gadget acts as a USB Mass Storage disk drive.
	  As its storage repository it can use a regular file or a block
	  device (in much the same way as the "loop" device driver),
	  specified as a module parameter or sysfs option.

config USB_CONFIGFS_F_LB_SS
	boolean "Loopback and sourcesink function (for testing)"
	depends on USB_CONFIGFS
	select USB_F_SS_LB
	help
	  Loopback function loops back a configurable number of transfers.
	  Sourcesink function either sinks and sources bulk data.
	  It also implements control requests, for "chapter 9" conformance.
	  Make this be the first driver you try using on top of any new
	  USB peripheral controller driver.  Then you can use host-side
	  test software, like the "usbtest" driver, to put your hardware
	  and its driver through a basic set of functional tests.

config USB_CONFIGFS_F_FS
	boolean "Function filesystem (FunctionFS)"
	depends on USB_CONFIGFS
	select USB_F_FS
	help
	  The Function Filesystem (FunctionFS) lets one create USB
	  composite functions in user space in the same way GadgetFS
	  lets one create USB gadgets in user space.  This allows creation
	  of composite gadgets such that some of the functions are
	  implemented in kernel space (for instance Ethernet, serial or
	  mass storage) and other are implemented in user space.

source "drivers/usb/gadget/legacy/Kconfig"

endchoice

endif # USB_GADGET