1 // SPDX-License-Identifier: GPL-2.0 2 /** 3 * core.c - DesignWare USB3 DRD Controller Core file 4 * 5 * Copyright (C) 2010-2011 Texas Instruments Incorporated - http://www.ti.com 6 * 7 * Authors: Felipe Balbi <balbi@ti.com>, 8 * Sebastian Andrzej Siewior <bigeasy@linutronix.de> 9 */ 10 11 #include <linux/clk.h> 12 #include <linux/version.h> 13 #include <linux/module.h> 14 #include <linux/kernel.h> 15 #include <linux/slab.h> 16 #include <linux/spinlock.h> 17 #include <linux/platform_device.h> 18 #include <linux/pm_runtime.h> 19 #include <linux/interrupt.h> 20 #include <linux/ioport.h> 21 #include <linux/io.h> 22 #include <linux/list.h> 23 #include <linux/delay.h> 24 #include <linux/dma-mapping.h> 25 #include <linux/of.h> 26 #include <linux/acpi.h> 27 #include <linux/pinctrl/consumer.h> 28 #include <linux/reset.h> 29 30 #include <linux/usb/ch9.h> 31 #include <linux/usb/gadget.h> 32 #include <linux/usb/of.h> 33 #include <linux/usb/otg.h> 34 35 #include "core.h" 36 #include "gadget.h" 37 #include "io.h" 38 39 #include "debug.h" 40 41 #define DWC3_DEFAULT_AUTOSUSPEND_DELAY 5000 /* ms */ 42 43 /** 44 * dwc3_get_dr_mode - Validates and sets dr_mode 45 * @dwc: pointer to our context structure 46 */ 47 static int dwc3_get_dr_mode(struct dwc3 *dwc) 48 { 49 enum usb_dr_mode mode; 50 struct device *dev = dwc->dev; 51 unsigned int hw_mode; 52 53 if (dwc->dr_mode == USB_DR_MODE_UNKNOWN) 54 dwc->dr_mode = USB_DR_MODE_OTG; 55 56 mode = dwc->dr_mode; 57 hw_mode = DWC3_GHWPARAMS0_MODE(dwc->hwparams.hwparams0); 58 59 switch (hw_mode) { 60 case DWC3_GHWPARAMS0_MODE_GADGET: 61 if (IS_ENABLED(CONFIG_USB_DWC3_HOST)) { 62 dev_err(dev, 63 "Controller does not support host mode.\n"); 64 return -EINVAL; 65 } 66 mode = USB_DR_MODE_PERIPHERAL; 67 break; 68 case DWC3_GHWPARAMS0_MODE_HOST: 69 if (IS_ENABLED(CONFIG_USB_DWC3_GADGET)) { 70 dev_err(dev, 71 "Controller does not support device mode.\n"); 72 return -EINVAL; 73 } 74 mode = USB_DR_MODE_HOST; 75 break; 76 default: 77 if (IS_ENABLED(CONFIG_USB_DWC3_HOST)) 78 mode = USB_DR_MODE_HOST; 79 else if (IS_ENABLED(CONFIG_USB_DWC3_GADGET)) 80 mode = USB_DR_MODE_PERIPHERAL; 81 82 /* 83 * dwc_usb31 does not support OTG mode. If the controller 84 * supports DRD but the dr_mode is not specified or set to OTG, 85 * then set the mode to peripheral. 86 */ 87 if (mode == USB_DR_MODE_OTG && dwc3_is_usb31(dwc)) 88 mode = USB_DR_MODE_PERIPHERAL; 89 } 90 91 if (mode != dwc->dr_mode) { 92 dev_warn(dev, 93 "Configuration mismatch. dr_mode forced to %s\n", 94 mode == USB_DR_MODE_HOST ? "host" : "gadget"); 95 96 dwc->dr_mode = mode; 97 } 98 99 return 0; 100 } 101 102 void dwc3_set_prtcap(struct dwc3 *dwc, u32 mode) 103 { 104 u32 reg; 105 106 reg = dwc3_readl(dwc->regs, DWC3_GCTL); 107 reg &= ~(DWC3_GCTL_PRTCAPDIR(DWC3_GCTL_PRTCAP_OTG)); 108 reg |= DWC3_GCTL_PRTCAPDIR(mode); 109 dwc3_writel(dwc->regs, DWC3_GCTL, reg); 110 111 dwc->current_dr_role = mode; 112 } 113 114 static void __dwc3_set_mode(struct work_struct *work) 115 { 116 struct dwc3 *dwc = work_to_dwc(work); 117 unsigned long flags; 118 int ret; 119 120 if (dwc->dr_mode != USB_DR_MODE_OTG) 121 return; 122 123 if (dwc->current_dr_role == DWC3_GCTL_PRTCAP_OTG) 124 dwc3_otg_update(dwc, 0); 125 126 if (!dwc->desired_dr_role) 127 return; 128 129 if (dwc->desired_dr_role == dwc->current_dr_role) 130 return; 131 132 if (dwc->desired_dr_role == DWC3_GCTL_PRTCAP_OTG && dwc->edev) 133 return; 134 135 switch (dwc->current_dr_role) { 136 case DWC3_GCTL_PRTCAP_HOST: 137 dwc3_host_exit(dwc); 138 break; 139 case DWC3_GCTL_PRTCAP_DEVICE: 140 dwc3_gadget_exit(dwc); 141 dwc3_event_buffers_cleanup(dwc); 142 break; 143 case DWC3_GCTL_PRTCAP_OTG: 144 dwc3_otg_exit(dwc); 145 spin_lock_irqsave(&dwc->lock, flags); 146 dwc->desired_otg_role = DWC3_OTG_ROLE_IDLE; 147 spin_unlock_irqrestore(&dwc->lock, flags); 148 dwc3_otg_update(dwc, 1); 149 break; 150 default: 151 break; 152 } 153 154 spin_lock_irqsave(&dwc->lock, flags); 155 156 dwc3_set_prtcap(dwc, dwc->desired_dr_role); 157 158 spin_unlock_irqrestore(&dwc->lock, flags); 159 160 switch (dwc->desired_dr_role) { 161 case DWC3_GCTL_PRTCAP_HOST: 162 ret = dwc3_host_init(dwc); 163 if (ret) { 164 dev_err(dwc->dev, "failed to initialize host\n"); 165 } else { 166 if (dwc->usb2_phy) 167 otg_set_vbus(dwc->usb2_phy->otg, true); 168 phy_set_mode(dwc->usb2_generic_phy, PHY_MODE_USB_HOST); 169 phy_set_mode(dwc->usb3_generic_phy, PHY_MODE_USB_HOST); 170 phy_calibrate(dwc->usb2_generic_phy); 171 } 172 break; 173 case DWC3_GCTL_PRTCAP_DEVICE: 174 dwc3_event_buffers_setup(dwc); 175 176 if (dwc->usb2_phy) 177 otg_set_vbus(dwc->usb2_phy->otg, false); 178 phy_set_mode(dwc->usb2_generic_phy, PHY_MODE_USB_DEVICE); 179 phy_set_mode(dwc->usb3_generic_phy, PHY_MODE_USB_DEVICE); 180 181 ret = dwc3_gadget_init(dwc); 182 if (ret) 183 dev_err(dwc->dev, "failed to initialize peripheral\n"); 184 break; 185 case DWC3_GCTL_PRTCAP_OTG: 186 dwc3_otg_init(dwc); 187 dwc3_otg_update(dwc, 0); 188 break; 189 default: 190 break; 191 } 192 193 } 194 195 void dwc3_set_mode(struct dwc3 *dwc, u32 mode) 196 { 197 unsigned long flags; 198 199 spin_lock_irqsave(&dwc->lock, flags); 200 dwc->desired_dr_role = mode; 201 spin_unlock_irqrestore(&dwc->lock, flags); 202 203 queue_work(system_freezable_wq, &dwc->drd_work); 204 } 205 206 u32 dwc3_core_fifo_space(struct dwc3_ep *dep, u8 type) 207 { 208 struct dwc3 *dwc = dep->dwc; 209 u32 reg; 210 211 dwc3_writel(dwc->regs, DWC3_GDBGFIFOSPACE, 212 DWC3_GDBGFIFOSPACE_NUM(dep->number) | 213 DWC3_GDBGFIFOSPACE_TYPE(type)); 214 215 reg = dwc3_readl(dwc->regs, DWC3_GDBGFIFOSPACE); 216 217 return DWC3_GDBGFIFOSPACE_SPACE_AVAILABLE(reg); 218 } 219 220 /** 221 * dwc3_core_soft_reset - Issues core soft reset and PHY reset 222 * @dwc: pointer to our context structure 223 */ 224 static int dwc3_core_soft_reset(struct dwc3 *dwc) 225 { 226 u32 reg; 227 int retries = 1000; 228 int ret; 229 230 usb_phy_init(dwc->usb2_phy); 231 usb_phy_init(dwc->usb3_phy); 232 ret = phy_init(dwc->usb2_generic_phy); 233 if (ret < 0) 234 return ret; 235 236 ret = phy_init(dwc->usb3_generic_phy); 237 if (ret < 0) { 238 phy_exit(dwc->usb2_generic_phy); 239 return ret; 240 } 241 242 /* 243 * We're resetting only the device side because, if we're in host mode, 244 * XHCI driver will reset the host block. If dwc3 was configured for 245 * host-only mode, then we can return early. 246 */ 247 if (dwc->current_dr_role == DWC3_GCTL_PRTCAP_HOST) 248 return 0; 249 250 reg = dwc3_readl(dwc->regs, DWC3_DCTL); 251 reg |= DWC3_DCTL_CSFTRST; 252 dwc3_writel(dwc->regs, DWC3_DCTL, reg); 253 254 do { 255 reg = dwc3_readl(dwc->regs, DWC3_DCTL); 256 if (!(reg & DWC3_DCTL_CSFTRST)) 257 goto done; 258 259 udelay(1); 260 } while (--retries); 261 262 phy_exit(dwc->usb3_generic_phy); 263 phy_exit(dwc->usb2_generic_phy); 264 265 return -ETIMEDOUT; 266 267 done: 268 /* 269 * For DWC_usb31 controller, once DWC3_DCTL_CSFTRST bit is cleared, 270 * we must wait at least 50ms before accessing the PHY domain 271 * (synchronization delay). DWC_usb31 programming guide section 1.3.2. 272 */ 273 if (dwc3_is_usb31(dwc)) 274 msleep(50); 275 276 return 0; 277 } 278 279 static const struct clk_bulk_data dwc3_core_clks[] = { 280 { .id = "ref" }, 281 { .id = "bus_early" }, 282 { .id = "suspend" }, 283 }; 284 285 /* 286 * dwc3_frame_length_adjustment - Adjusts frame length if required 287 * @dwc3: Pointer to our controller context structure 288 */ 289 static void dwc3_frame_length_adjustment(struct dwc3 *dwc) 290 { 291 u32 reg; 292 u32 dft; 293 294 if (dwc->revision < DWC3_REVISION_250A) 295 return; 296 297 if (dwc->fladj == 0) 298 return; 299 300 reg = dwc3_readl(dwc->regs, DWC3_GFLADJ); 301 dft = reg & DWC3_GFLADJ_30MHZ_MASK; 302 if (!dev_WARN_ONCE(dwc->dev, dft == dwc->fladj, 303 "request value same as default, ignoring\n")) { 304 reg &= ~DWC3_GFLADJ_30MHZ_MASK; 305 reg |= DWC3_GFLADJ_30MHZ_SDBND_SEL | dwc->fladj; 306 dwc3_writel(dwc->regs, DWC3_GFLADJ, reg); 307 } 308 } 309 310 /** 311 * dwc3_free_one_event_buffer - Frees one event buffer 312 * @dwc: Pointer to our controller context structure 313 * @evt: Pointer to event buffer to be freed 314 */ 315 static void dwc3_free_one_event_buffer(struct dwc3 *dwc, 316 struct dwc3_event_buffer *evt) 317 { 318 dma_free_coherent(dwc->sysdev, evt->length, evt->buf, evt->dma); 319 } 320 321 /** 322 * dwc3_alloc_one_event_buffer - Allocates one event buffer structure 323 * @dwc: Pointer to our controller context structure 324 * @length: size of the event buffer 325 * 326 * Returns a pointer to the allocated event buffer structure on success 327 * otherwise ERR_PTR(errno). 328 */ 329 static struct dwc3_event_buffer *dwc3_alloc_one_event_buffer(struct dwc3 *dwc, 330 unsigned length) 331 { 332 struct dwc3_event_buffer *evt; 333 334 evt = devm_kzalloc(dwc->dev, sizeof(*evt), GFP_KERNEL); 335 if (!evt) 336 return ERR_PTR(-ENOMEM); 337 338 evt->dwc = dwc; 339 evt->length = length; 340 evt->cache = devm_kzalloc(dwc->dev, length, GFP_KERNEL); 341 if (!evt->cache) 342 return ERR_PTR(-ENOMEM); 343 344 evt->buf = dma_alloc_coherent(dwc->sysdev, length, 345 &evt->dma, GFP_KERNEL); 346 if (!evt->buf) 347 return ERR_PTR(-ENOMEM); 348 349 return evt; 350 } 351 352 /** 353 * dwc3_free_event_buffers - frees all allocated event buffers 354 * @dwc: Pointer to our controller context structure 355 */ 356 static void dwc3_free_event_buffers(struct dwc3 *dwc) 357 { 358 struct dwc3_event_buffer *evt; 359 360 evt = dwc->ev_buf; 361 if (evt) 362 dwc3_free_one_event_buffer(dwc, evt); 363 } 364 365 /** 366 * dwc3_alloc_event_buffers - Allocates @num event buffers of size @length 367 * @dwc: pointer to our controller context structure 368 * @length: size of event buffer 369 * 370 * Returns 0 on success otherwise negative errno. In the error case, dwc 371 * may contain some buffers allocated but not all which were requested. 372 */ 373 static int dwc3_alloc_event_buffers(struct dwc3 *dwc, unsigned length) 374 { 375 struct dwc3_event_buffer *evt; 376 377 evt = dwc3_alloc_one_event_buffer(dwc, length); 378 if (IS_ERR(evt)) { 379 dev_err(dwc->dev, "can't allocate event buffer\n"); 380 return PTR_ERR(evt); 381 } 382 dwc->ev_buf = evt; 383 384 return 0; 385 } 386 387 /** 388 * dwc3_event_buffers_setup - setup our allocated event buffers 389 * @dwc: pointer to our controller context structure 390 * 391 * Returns 0 on success otherwise negative errno. 392 */ 393 int dwc3_event_buffers_setup(struct dwc3 *dwc) 394 { 395 struct dwc3_event_buffer *evt; 396 397 evt = dwc->ev_buf; 398 evt->lpos = 0; 399 dwc3_writel(dwc->regs, DWC3_GEVNTADRLO(0), 400 lower_32_bits(evt->dma)); 401 dwc3_writel(dwc->regs, DWC3_GEVNTADRHI(0), 402 upper_32_bits(evt->dma)); 403 dwc3_writel(dwc->regs, DWC3_GEVNTSIZ(0), 404 DWC3_GEVNTSIZ_SIZE(evt->length)); 405 dwc3_writel(dwc->regs, DWC3_GEVNTCOUNT(0), 0); 406 407 return 0; 408 } 409 410 void dwc3_event_buffers_cleanup(struct dwc3 *dwc) 411 { 412 struct dwc3_event_buffer *evt; 413 414 evt = dwc->ev_buf; 415 416 evt->lpos = 0; 417 418 dwc3_writel(dwc->regs, DWC3_GEVNTADRLO(0), 0); 419 dwc3_writel(dwc->regs, DWC3_GEVNTADRHI(0), 0); 420 dwc3_writel(dwc->regs, DWC3_GEVNTSIZ(0), DWC3_GEVNTSIZ_INTMASK 421 | DWC3_GEVNTSIZ_SIZE(0)); 422 dwc3_writel(dwc->regs, DWC3_GEVNTCOUNT(0), 0); 423 } 424 425 static int dwc3_alloc_scratch_buffers(struct dwc3 *dwc) 426 { 427 if (!dwc->has_hibernation) 428 return 0; 429 430 if (!dwc->nr_scratch) 431 return 0; 432 433 dwc->scratchbuf = kmalloc_array(dwc->nr_scratch, 434 DWC3_SCRATCHBUF_SIZE, GFP_KERNEL); 435 if (!dwc->scratchbuf) 436 return -ENOMEM; 437 438 return 0; 439 } 440 441 static int dwc3_setup_scratch_buffers(struct dwc3 *dwc) 442 { 443 dma_addr_t scratch_addr; 444 u32 param; 445 int ret; 446 447 if (!dwc->has_hibernation) 448 return 0; 449 450 if (!dwc->nr_scratch) 451 return 0; 452 453 /* should never fall here */ 454 if (!WARN_ON(dwc->scratchbuf)) 455 return 0; 456 457 scratch_addr = dma_map_single(dwc->sysdev, dwc->scratchbuf, 458 dwc->nr_scratch * DWC3_SCRATCHBUF_SIZE, 459 DMA_BIDIRECTIONAL); 460 if (dma_mapping_error(dwc->sysdev, scratch_addr)) { 461 dev_err(dwc->sysdev, "failed to map scratch buffer\n"); 462 ret = -EFAULT; 463 goto err0; 464 } 465 466 dwc->scratch_addr = scratch_addr; 467 468 param = lower_32_bits(scratch_addr); 469 470 ret = dwc3_send_gadget_generic_command(dwc, 471 DWC3_DGCMD_SET_SCRATCHPAD_ADDR_LO, param); 472 if (ret < 0) 473 goto err1; 474 475 param = upper_32_bits(scratch_addr); 476 477 ret = dwc3_send_gadget_generic_command(dwc, 478 DWC3_DGCMD_SET_SCRATCHPAD_ADDR_HI, param); 479 if (ret < 0) 480 goto err1; 481 482 return 0; 483 484 err1: 485 dma_unmap_single(dwc->sysdev, dwc->scratch_addr, dwc->nr_scratch * 486 DWC3_SCRATCHBUF_SIZE, DMA_BIDIRECTIONAL); 487 488 err0: 489 return ret; 490 } 491 492 static void dwc3_free_scratch_buffers(struct dwc3 *dwc) 493 { 494 if (!dwc->has_hibernation) 495 return; 496 497 if (!dwc->nr_scratch) 498 return; 499 500 /* should never fall here */ 501 if (!WARN_ON(dwc->scratchbuf)) 502 return; 503 504 dma_unmap_single(dwc->sysdev, dwc->scratch_addr, dwc->nr_scratch * 505 DWC3_SCRATCHBUF_SIZE, DMA_BIDIRECTIONAL); 506 kfree(dwc->scratchbuf); 507 } 508 509 static void dwc3_core_num_eps(struct dwc3 *dwc) 510 { 511 struct dwc3_hwparams *parms = &dwc->hwparams; 512 513 dwc->num_eps = DWC3_NUM_EPS(parms); 514 } 515 516 static void dwc3_cache_hwparams(struct dwc3 *dwc) 517 { 518 struct dwc3_hwparams *parms = &dwc->hwparams; 519 520 parms->hwparams0 = dwc3_readl(dwc->regs, DWC3_GHWPARAMS0); 521 parms->hwparams1 = dwc3_readl(dwc->regs, DWC3_GHWPARAMS1); 522 parms->hwparams2 = dwc3_readl(dwc->regs, DWC3_GHWPARAMS2); 523 parms->hwparams3 = dwc3_readl(dwc->regs, DWC3_GHWPARAMS3); 524 parms->hwparams4 = dwc3_readl(dwc->regs, DWC3_GHWPARAMS4); 525 parms->hwparams5 = dwc3_readl(dwc->regs, DWC3_GHWPARAMS5); 526 parms->hwparams6 = dwc3_readl(dwc->regs, DWC3_GHWPARAMS6); 527 parms->hwparams7 = dwc3_readl(dwc->regs, DWC3_GHWPARAMS7); 528 parms->hwparams8 = dwc3_readl(dwc->regs, DWC3_GHWPARAMS8); 529 } 530 531 static int dwc3_core_ulpi_init(struct dwc3 *dwc) 532 { 533 int intf; 534 int ret = 0; 535 536 intf = DWC3_GHWPARAMS3_HSPHY_IFC(dwc->hwparams.hwparams3); 537 538 if (intf == DWC3_GHWPARAMS3_HSPHY_IFC_ULPI || 539 (intf == DWC3_GHWPARAMS3_HSPHY_IFC_UTMI_ULPI && 540 dwc->hsphy_interface && 541 !strncmp(dwc->hsphy_interface, "ulpi", 4))) 542 ret = dwc3_ulpi_init(dwc); 543 544 return ret; 545 } 546 547 /** 548 * dwc3_phy_setup - Configure USB PHY Interface of DWC3 Core 549 * @dwc: Pointer to our controller context structure 550 * 551 * Returns 0 on success. The USB PHY interfaces are configured but not 552 * initialized. The PHY interfaces and the PHYs get initialized together with 553 * the core in dwc3_core_init. 554 */ 555 static int dwc3_phy_setup(struct dwc3 *dwc) 556 { 557 u32 reg; 558 559 reg = dwc3_readl(dwc->regs, DWC3_GUSB3PIPECTL(0)); 560 561 /* 562 * Make sure UX_EXIT_PX is cleared as that causes issues with some 563 * PHYs. Also, this bit is not supposed to be used in normal operation. 564 */ 565 reg &= ~DWC3_GUSB3PIPECTL_UX_EXIT_PX; 566 567 /* 568 * Above 1.94a, it is recommended to set DWC3_GUSB3PIPECTL_SUSPHY 569 * to '0' during coreConsultant configuration. So default value 570 * will be '0' when the core is reset. Application needs to set it 571 * to '1' after the core initialization is completed. 572 */ 573 if (dwc->revision > DWC3_REVISION_194A) 574 reg |= DWC3_GUSB3PIPECTL_SUSPHY; 575 576 if (dwc->u2ss_inp3_quirk) 577 reg |= DWC3_GUSB3PIPECTL_U2SSINP3OK; 578 579 if (dwc->dis_rxdet_inp3_quirk) 580 reg |= DWC3_GUSB3PIPECTL_DISRXDETINP3; 581 582 if (dwc->req_p1p2p3_quirk) 583 reg |= DWC3_GUSB3PIPECTL_REQP1P2P3; 584 585 if (dwc->del_p1p2p3_quirk) 586 reg |= DWC3_GUSB3PIPECTL_DEP1P2P3_EN; 587 588 if (dwc->del_phy_power_chg_quirk) 589 reg |= DWC3_GUSB3PIPECTL_DEPOCHANGE; 590 591 if (dwc->lfps_filter_quirk) 592 reg |= DWC3_GUSB3PIPECTL_LFPSFILT; 593 594 if (dwc->rx_detect_poll_quirk) 595 reg |= DWC3_GUSB3PIPECTL_RX_DETOPOLL; 596 597 if (dwc->tx_de_emphasis_quirk) 598 reg |= DWC3_GUSB3PIPECTL_TX_DEEPH(dwc->tx_de_emphasis); 599 600 if (dwc->dis_u3_susphy_quirk) 601 reg &= ~DWC3_GUSB3PIPECTL_SUSPHY; 602 603 if (dwc->dis_del_phy_power_chg_quirk) 604 reg &= ~DWC3_GUSB3PIPECTL_DEPOCHANGE; 605 606 dwc3_writel(dwc->regs, DWC3_GUSB3PIPECTL(0), reg); 607 608 reg = dwc3_readl(dwc->regs, DWC3_GUSB2PHYCFG(0)); 609 610 /* Select the HS PHY interface */ 611 switch (DWC3_GHWPARAMS3_HSPHY_IFC(dwc->hwparams.hwparams3)) { 612 case DWC3_GHWPARAMS3_HSPHY_IFC_UTMI_ULPI: 613 if (dwc->hsphy_interface && 614 !strncmp(dwc->hsphy_interface, "utmi", 4)) { 615 reg &= ~DWC3_GUSB2PHYCFG_ULPI_UTMI; 616 break; 617 } else if (dwc->hsphy_interface && 618 !strncmp(dwc->hsphy_interface, "ulpi", 4)) { 619 reg |= DWC3_GUSB2PHYCFG_ULPI_UTMI; 620 dwc3_writel(dwc->regs, DWC3_GUSB2PHYCFG(0), reg); 621 } else { 622 /* Relying on default value. */ 623 if (!(reg & DWC3_GUSB2PHYCFG_ULPI_UTMI)) 624 break; 625 } 626 /* FALLTHROUGH */ 627 case DWC3_GHWPARAMS3_HSPHY_IFC_ULPI: 628 /* FALLTHROUGH */ 629 default: 630 break; 631 } 632 633 switch (dwc->hsphy_mode) { 634 case USBPHY_INTERFACE_MODE_UTMI: 635 reg &= ~(DWC3_GUSB2PHYCFG_PHYIF_MASK | 636 DWC3_GUSB2PHYCFG_USBTRDTIM_MASK); 637 reg |= DWC3_GUSB2PHYCFG_PHYIF(UTMI_PHYIF_8_BIT) | 638 DWC3_GUSB2PHYCFG_USBTRDTIM(USBTRDTIM_UTMI_8_BIT); 639 break; 640 case USBPHY_INTERFACE_MODE_UTMIW: 641 reg &= ~(DWC3_GUSB2PHYCFG_PHYIF_MASK | 642 DWC3_GUSB2PHYCFG_USBTRDTIM_MASK); 643 reg |= DWC3_GUSB2PHYCFG_PHYIF(UTMI_PHYIF_16_BIT) | 644 DWC3_GUSB2PHYCFG_USBTRDTIM(USBTRDTIM_UTMI_16_BIT); 645 break; 646 default: 647 break; 648 } 649 650 /* 651 * Above 1.94a, it is recommended to set DWC3_GUSB2PHYCFG_SUSPHY to 652 * '0' during coreConsultant configuration. So default value will 653 * be '0' when the core is reset. Application needs to set it to 654 * '1' after the core initialization is completed. 655 */ 656 if (dwc->revision > DWC3_REVISION_194A) 657 reg |= DWC3_GUSB2PHYCFG_SUSPHY; 658 659 if (dwc->dis_u2_susphy_quirk) 660 reg &= ~DWC3_GUSB2PHYCFG_SUSPHY; 661 662 if (dwc->dis_enblslpm_quirk) 663 reg &= ~DWC3_GUSB2PHYCFG_ENBLSLPM; 664 665 if (dwc->dis_u2_freeclk_exists_quirk) 666 reg &= ~DWC3_GUSB2PHYCFG_U2_FREECLK_EXISTS; 667 668 dwc3_writel(dwc->regs, DWC3_GUSB2PHYCFG(0), reg); 669 670 return 0; 671 } 672 673 static void dwc3_core_exit(struct dwc3 *dwc) 674 { 675 dwc3_event_buffers_cleanup(dwc); 676 677 usb_phy_shutdown(dwc->usb2_phy); 678 usb_phy_shutdown(dwc->usb3_phy); 679 phy_exit(dwc->usb2_generic_phy); 680 phy_exit(dwc->usb3_generic_phy); 681 682 usb_phy_set_suspend(dwc->usb2_phy, 1); 683 usb_phy_set_suspend(dwc->usb3_phy, 1); 684 phy_power_off(dwc->usb2_generic_phy); 685 phy_power_off(dwc->usb3_generic_phy); 686 clk_bulk_disable(dwc->num_clks, dwc->clks); 687 clk_bulk_unprepare(dwc->num_clks, dwc->clks); 688 reset_control_assert(dwc->reset); 689 } 690 691 static bool dwc3_core_is_valid(struct dwc3 *dwc) 692 { 693 u32 reg; 694 695 reg = dwc3_readl(dwc->regs, DWC3_GSNPSID); 696 697 /* This should read as U3 followed by revision number */ 698 if ((reg & DWC3_GSNPSID_MASK) == 0x55330000) { 699 /* Detected DWC_usb3 IP */ 700 dwc->revision = reg; 701 } else if ((reg & DWC3_GSNPSID_MASK) == 0x33310000) { 702 /* Detected DWC_usb31 IP */ 703 dwc->revision = dwc3_readl(dwc->regs, DWC3_VER_NUMBER); 704 dwc->revision |= DWC3_REVISION_IS_DWC31; 705 } else { 706 return false; 707 } 708 709 return true; 710 } 711 712 static void dwc3_core_setup_global_control(struct dwc3 *dwc) 713 { 714 u32 hwparams4 = dwc->hwparams.hwparams4; 715 u32 reg; 716 717 reg = dwc3_readl(dwc->regs, DWC3_GCTL); 718 reg &= ~DWC3_GCTL_SCALEDOWN_MASK; 719 720 switch (DWC3_GHWPARAMS1_EN_PWROPT(dwc->hwparams.hwparams1)) { 721 case DWC3_GHWPARAMS1_EN_PWROPT_CLK: 722 /** 723 * WORKAROUND: DWC3 revisions between 2.10a and 2.50a have an 724 * issue which would cause xHCI compliance tests to fail. 725 * 726 * Because of that we cannot enable clock gating on such 727 * configurations. 728 * 729 * Refers to: 730 * 731 * STAR#9000588375: Clock Gating, SOF Issues when ref_clk-Based 732 * SOF/ITP Mode Used 733 */ 734 if ((dwc->dr_mode == USB_DR_MODE_HOST || 735 dwc->dr_mode == USB_DR_MODE_OTG) && 736 (dwc->revision >= DWC3_REVISION_210A && 737 dwc->revision <= DWC3_REVISION_250A)) 738 reg |= DWC3_GCTL_DSBLCLKGTNG | DWC3_GCTL_SOFITPSYNC; 739 else 740 reg &= ~DWC3_GCTL_DSBLCLKGTNG; 741 break; 742 case DWC3_GHWPARAMS1_EN_PWROPT_HIB: 743 /* enable hibernation here */ 744 dwc->nr_scratch = DWC3_GHWPARAMS4_HIBER_SCRATCHBUFS(hwparams4); 745 746 /* 747 * REVISIT Enabling this bit so that host-mode hibernation 748 * will work. Device-mode hibernation is not yet implemented. 749 */ 750 reg |= DWC3_GCTL_GBLHIBERNATIONEN; 751 break; 752 default: 753 /* nothing */ 754 break; 755 } 756 757 /* check if current dwc3 is on simulation board */ 758 if (dwc->hwparams.hwparams6 & DWC3_GHWPARAMS6_EN_FPGA) { 759 dev_info(dwc->dev, "Running with FPGA optmizations\n"); 760 dwc->is_fpga = true; 761 } 762 763 WARN_ONCE(dwc->disable_scramble_quirk && !dwc->is_fpga, 764 "disable_scramble cannot be used on non-FPGA builds\n"); 765 766 if (dwc->disable_scramble_quirk && dwc->is_fpga) 767 reg |= DWC3_GCTL_DISSCRAMBLE; 768 else 769 reg &= ~DWC3_GCTL_DISSCRAMBLE; 770 771 if (dwc->u2exit_lfps_quirk) 772 reg |= DWC3_GCTL_U2EXIT_LFPS; 773 774 /* 775 * WORKAROUND: DWC3 revisions <1.90a have a bug 776 * where the device can fail to connect at SuperSpeed 777 * and falls back to high-speed mode which causes 778 * the device to enter a Connect/Disconnect loop 779 */ 780 if (dwc->revision < DWC3_REVISION_190A) 781 reg |= DWC3_GCTL_U2RSTECN; 782 783 dwc3_writel(dwc->regs, DWC3_GCTL, reg); 784 } 785 786 static int dwc3_core_get_phy(struct dwc3 *dwc); 787 static int dwc3_core_ulpi_init(struct dwc3 *dwc); 788 789 /* set global incr burst type configuration registers */ 790 static void dwc3_set_incr_burst_type(struct dwc3 *dwc) 791 { 792 struct device *dev = dwc->dev; 793 /* incrx_mode : for INCR burst type. */ 794 bool incrx_mode; 795 /* incrx_size : for size of INCRX burst. */ 796 u32 incrx_size; 797 u32 *vals; 798 u32 cfg; 799 int ntype; 800 int ret; 801 int i; 802 803 cfg = dwc3_readl(dwc->regs, DWC3_GSBUSCFG0); 804 805 /* 806 * Handle property "snps,incr-burst-type-adjustment". 807 * Get the number of value from this property: 808 * result <= 0, means this property is not supported. 809 * result = 1, means INCRx burst mode supported. 810 * result > 1, means undefined length burst mode supported. 811 */ 812 ntype = device_property_read_u32_array(dev, 813 "snps,incr-burst-type-adjustment", NULL, 0); 814 if (ntype <= 0) 815 return; 816 817 vals = kcalloc(ntype, sizeof(u32), GFP_KERNEL); 818 if (!vals) { 819 dev_err(dev, "Error to get memory\n"); 820 return; 821 } 822 823 /* Get INCR burst type, and parse it */ 824 ret = device_property_read_u32_array(dev, 825 "snps,incr-burst-type-adjustment", vals, ntype); 826 if (ret) { 827 dev_err(dev, "Error to get property\n"); 828 return; 829 } 830 831 incrx_size = *vals; 832 833 if (ntype > 1) { 834 /* INCRX (undefined length) burst mode */ 835 incrx_mode = INCRX_UNDEF_LENGTH_BURST_MODE; 836 for (i = 1; i < ntype; i++) { 837 if (vals[i] > incrx_size) 838 incrx_size = vals[i]; 839 } 840 } else { 841 /* INCRX burst mode */ 842 incrx_mode = INCRX_BURST_MODE; 843 } 844 845 /* Enable Undefined Length INCR Burst and Enable INCRx Burst */ 846 cfg &= ~DWC3_GSBUSCFG0_INCRBRST_MASK; 847 if (incrx_mode) 848 cfg |= DWC3_GSBUSCFG0_INCRBRSTENA; 849 switch (incrx_size) { 850 case 256: 851 cfg |= DWC3_GSBUSCFG0_INCR256BRSTENA; 852 break; 853 case 128: 854 cfg |= DWC3_GSBUSCFG0_INCR128BRSTENA; 855 break; 856 case 64: 857 cfg |= DWC3_GSBUSCFG0_INCR64BRSTENA; 858 break; 859 case 32: 860 cfg |= DWC3_GSBUSCFG0_INCR32BRSTENA; 861 break; 862 case 16: 863 cfg |= DWC3_GSBUSCFG0_INCR16BRSTENA; 864 break; 865 case 8: 866 cfg |= DWC3_GSBUSCFG0_INCR8BRSTENA; 867 break; 868 case 4: 869 cfg |= DWC3_GSBUSCFG0_INCR4BRSTENA; 870 break; 871 case 1: 872 break; 873 default: 874 dev_err(dev, "Invalid property\n"); 875 break; 876 } 877 878 dwc3_writel(dwc->regs, DWC3_GSBUSCFG0, cfg); 879 } 880 881 /** 882 * dwc3_core_init - Low-level initialization of DWC3 Core 883 * @dwc: Pointer to our controller context structure 884 * 885 * Returns 0 on success otherwise negative errno. 886 */ 887 static int dwc3_core_init(struct dwc3 *dwc) 888 { 889 u32 reg; 890 int ret; 891 892 if (!dwc3_core_is_valid(dwc)) { 893 dev_err(dwc->dev, "this is not a DesignWare USB3 DRD Core\n"); 894 ret = -ENODEV; 895 goto err0; 896 } 897 898 /* 899 * Write Linux Version Code to our GUID register so it's easy to figure 900 * out which kernel version a bug was found. 901 */ 902 dwc3_writel(dwc->regs, DWC3_GUID, LINUX_VERSION_CODE); 903 904 /* Handle USB2.0-only core configuration */ 905 if (DWC3_GHWPARAMS3_SSPHY_IFC(dwc->hwparams.hwparams3) == 906 DWC3_GHWPARAMS3_SSPHY_IFC_DIS) { 907 if (dwc->maximum_speed == USB_SPEED_SUPER) 908 dwc->maximum_speed = USB_SPEED_HIGH; 909 } 910 911 ret = dwc3_phy_setup(dwc); 912 if (ret) 913 goto err0; 914 915 if (!dwc->ulpi_ready) { 916 ret = dwc3_core_ulpi_init(dwc); 917 if (ret) 918 goto err0; 919 dwc->ulpi_ready = true; 920 } 921 922 if (!dwc->phys_ready) { 923 ret = dwc3_core_get_phy(dwc); 924 if (ret) 925 goto err0a; 926 dwc->phys_ready = true; 927 } 928 929 ret = dwc3_core_soft_reset(dwc); 930 if (ret) 931 goto err0a; 932 933 dwc3_core_setup_global_control(dwc); 934 dwc3_core_num_eps(dwc); 935 936 ret = dwc3_setup_scratch_buffers(dwc); 937 if (ret) 938 goto err1; 939 940 /* Adjust Frame Length */ 941 dwc3_frame_length_adjustment(dwc); 942 943 dwc3_set_incr_burst_type(dwc); 944 945 usb_phy_set_suspend(dwc->usb2_phy, 0); 946 usb_phy_set_suspend(dwc->usb3_phy, 0); 947 ret = phy_power_on(dwc->usb2_generic_phy); 948 if (ret < 0) 949 goto err2; 950 951 ret = phy_power_on(dwc->usb3_generic_phy); 952 if (ret < 0) 953 goto err3; 954 955 ret = dwc3_event_buffers_setup(dwc); 956 if (ret) { 957 dev_err(dwc->dev, "failed to setup event buffers\n"); 958 goto err4; 959 } 960 961 /* 962 * ENDXFER polling is available on version 3.10a and later of 963 * the DWC_usb3 controller. It is NOT available in the 964 * DWC_usb31 controller. 965 */ 966 if (!dwc3_is_usb31(dwc) && dwc->revision >= DWC3_REVISION_310A) { 967 reg = dwc3_readl(dwc->regs, DWC3_GUCTL2); 968 reg |= DWC3_GUCTL2_RST_ACTBITLATER; 969 dwc3_writel(dwc->regs, DWC3_GUCTL2, reg); 970 } 971 972 if (dwc->revision >= DWC3_REVISION_250A) { 973 reg = dwc3_readl(dwc->regs, DWC3_GUCTL1); 974 975 /* 976 * Enable hardware control of sending remote wakeup 977 * in HS when the device is in the L1 state. 978 */ 979 if (dwc->revision >= DWC3_REVISION_290A) 980 reg |= DWC3_GUCTL1_DEV_L1_EXIT_BY_HW; 981 982 if (dwc->dis_tx_ipgap_linecheck_quirk) 983 reg |= DWC3_GUCTL1_TX_IPGAP_LINECHECK_DIS; 984 985 dwc3_writel(dwc->regs, DWC3_GUCTL1, reg); 986 } 987 988 if (dwc->dr_mode == USB_DR_MODE_HOST || 989 dwc->dr_mode == USB_DR_MODE_OTG) { 990 reg = dwc3_readl(dwc->regs, DWC3_GUCTL); 991 992 /* 993 * Enable Auto retry Feature to make the controller operating in 994 * Host mode on seeing transaction errors(CRC errors or internal 995 * overrun scenerios) on IN transfers to reply to the device 996 * with a non-terminating retry ACK (i.e, an ACK transcation 997 * packet with Retry=1 & Nump != 0) 998 */ 999 reg |= DWC3_GUCTL_HSTINAUTORETRY; 1000 1001 dwc3_writel(dwc->regs, DWC3_GUCTL, reg); 1002 } 1003 1004 /* 1005 * Must config both number of packets and max burst settings to enable 1006 * RX and/or TX threshold. 1007 */ 1008 if (dwc3_is_usb31(dwc) && dwc->dr_mode == USB_DR_MODE_HOST) { 1009 u8 rx_thr_num = dwc->rx_thr_num_pkt_prd; 1010 u8 rx_maxburst = dwc->rx_max_burst_prd; 1011 u8 tx_thr_num = dwc->tx_thr_num_pkt_prd; 1012 u8 tx_maxburst = dwc->tx_max_burst_prd; 1013 1014 if (rx_thr_num && rx_maxburst) { 1015 reg = dwc3_readl(dwc->regs, DWC3_GRXTHRCFG); 1016 reg |= DWC31_RXTHRNUMPKTSEL_PRD; 1017 1018 reg &= ~DWC31_RXTHRNUMPKT_PRD(~0); 1019 reg |= DWC31_RXTHRNUMPKT_PRD(rx_thr_num); 1020 1021 reg &= ~DWC31_MAXRXBURSTSIZE_PRD(~0); 1022 reg |= DWC31_MAXRXBURSTSIZE_PRD(rx_maxburst); 1023 1024 dwc3_writel(dwc->regs, DWC3_GRXTHRCFG, reg); 1025 } 1026 1027 if (tx_thr_num && tx_maxburst) { 1028 reg = dwc3_readl(dwc->regs, DWC3_GTXTHRCFG); 1029 reg |= DWC31_TXTHRNUMPKTSEL_PRD; 1030 1031 reg &= ~DWC31_TXTHRNUMPKT_PRD(~0); 1032 reg |= DWC31_TXTHRNUMPKT_PRD(tx_thr_num); 1033 1034 reg &= ~DWC31_MAXTXBURSTSIZE_PRD(~0); 1035 reg |= DWC31_MAXTXBURSTSIZE_PRD(tx_maxburst); 1036 1037 dwc3_writel(dwc->regs, DWC3_GTXTHRCFG, reg); 1038 } 1039 } 1040 1041 return 0; 1042 1043 err4: 1044 phy_power_off(dwc->usb3_generic_phy); 1045 1046 err3: 1047 phy_power_off(dwc->usb2_generic_phy); 1048 1049 err2: 1050 usb_phy_set_suspend(dwc->usb2_phy, 1); 1051 usb_phy_set_suspend(dwc->usb3_phy, 1); 1052 1053 err1: 1054 usb_phy_shutdown(dwc->usb2_phy); 1055 usb_phy_shutdown(dwc->usb3_phy); 1056 phy_exit(dwc->usb2_generic_phy); 1057 phy_exit(dwc->usb3_generic_phy); 1058 1059 err0a: 1060 dwc3_ulpi_exit(dwc); 1061 1062 err0: 1063 return ret; 1064 } 1065 1066 static int dwc3_core_get_phy(struct dwc3 *dwc) 1067 { 1068 struct device *dev = dwc->dev; 1069 struct device_node *node = dev->of_node; 1070 int ret; 1071 1072 if (node) { 1073 dwc->usb2_phy = devm_usb_get_phy_by_phandle(dev, "usb-phy", 0); 1074 dwc->usb3_phy = devm_usb_get_phy_by_phandle(dev, "usb-phy", 1); 1075 } else { 1076 dwc->usb2_phy = devm_usb_get_phy(dev, USB_PHY_TYPE_USB2); 1077 dwc->usb3_phy = devm_usb_get_phy(dev, USB_PHY_TYPE_USB3); 1078 } 1079 1080 if (IS_ERR(dwc->usb2_phy)) { 1081 ret = PTR_ERR(dwc->usb2_phy); 1082 if (ret == -ENXIO || ret == -ENODEV) { 1083 dwc->usb2_phy = NULL; 1084 } else if (ret == -EPROBE_DEFER) { 1085 return ret; 1086 } else { 1087 dev_err(dev, "no usb2 phy configured\n"); 1088 return ret; 1089 } 1090 } 1091 1092 if (IS_ERR(dwc->usb3_phy)) { 1093 ret = PTR_ERR(dwc->usb3_phy); 1094 if (ret == -ENXIO || ret == -ENODEV) { 1095 dwc->usb3_phy = NULL; 1096 } else if (ret == -EPROBE_DEFER) { 1097 return ret; 1098 } else { 1099 dev_err(dev, "no usb3 phy configured\n"); 1100 return ret; 1101 } 1102 } 1103 1104 dwc->usb2_generic_phy = devm_phy_get(dev, "usb2-phy"); 1105 if (IS_ERR(dwc->usb2_generic_phy)) { 1106 ret = PTR_ERR(dwc->usb2_generic_phy); 1107 if (ret == -ENOSYS || ret == -ENODEV) { 1108 dwc->usb2_generic_phy = NULL; 1109 } else if (ret == -EPROBE_DEFER) { 1110 return ret; 1111 } else { 1112 dev_err(dev, "no usb2 phy configured\n"); 1113 return ret; 1114 } 1115 } 1116 1117 dwc->usb3_generic_phy = devm_phy_get(dev, "usb3-phy"); 1118 if (IS_ERR(dwc->usb3_generic_phy)) { 1119 ret = PTR_ERR(dwc->usb3_generic_phy); 1120 if (ret == -ENOSYS || ret == -ENODEV) { 1121 dwc->usb3_generic_phy = NULL; 1122 } else if (ret == -EPROBE_DEFER) { 1123 return ret; 1124 } else { 1125 dev_err(dev, "no usb3 phy configured\n"); 1126 return ret; 1127 } 1128 } 1129 1130 return 0; 1131 } 1132 1133 static int dwc3_core_init_mode(struct dwc3 *dwc) 1134 { 1135 struct device *dev = dwc->dev; 1136 int ret; 1137 1138 switch (dwc->dr_mode) { 1139 case USB_DR_MODE_PERIPHERAL: 1140 dwc3_set_prtcap(dwc, DWC3_GCTL_PRTCAP_DEVICE); 1141 1142 if (dwc->usb2_phy) 1143 otg_set_vbus(dwc->usb2_phy->otg, false); 1144 phy_set_mode(dwc->usb2_generic_phy, PHY_MODE_USB_DEVICE); 1145 phy_set_mode(dwc->usb3_generic_phy, PHY_MODE_USB_DEVICE); 1146 1147 ret = dwc3_gadget_init(dwc); 1148 if (ret) { 1149 if (ret != -EPROBE_DEFER) 1150 dev_err(dev, "failed to initialize gadget\n"); 1151 return ret; 1152 } 1153 break; 1154 case USB_DR_MODE_HOST: 1155 dwc3_set_prtcap(dwc, DWC3_GCTL_PRTCAP_HOST); 1156 1157 if (dwc->usb2_phy) 1158 otg_set_vbus(dwc->usb2_phy->otg, true); 1159 phy_set_mode(dwc->usb2_generic_phy, PHY_MODE_USB_HOST); 1160 phy_set_mode(dwc->usb3_generic_phy, PHY_MODE_USB_HOST); 1161 1162 ret = dwc3_host_init(dwc); 1163 if (ret) { 1164 if (ret != -EPROBE_DEFER) 1165 dev_err(dev, "failed to initialize host\n"); 1166 return ret; 1167 } 1168 phy_calibrate(dwc->usb2_generic_phy); 1169 break; 1170 case USB_DR_MODE_OTG: 1171 INIT_WORK(&dwc->drd_work, __dwc3_set_mode); 1172 ret = dwc3_drd_init(dwc); 1173 if (ret) { 1174 if (ret != -EPROBE_DEFER) 1175 dev_err(dev, "failed to initialize dual-role\n"); 1176 return ret; 1177 } 1178 break; 1179 default: 1180 dev_err(dev, "Unsupported mode of operation %d\n", dwc->dr_mode); 1181 return -EINVAL; 1182 } 1183 1184 return 0; 1185 } 1186 1187 static void dwc3_core_exit_mode(struct dwc3 *dwc) 1188 { 1189 switch (dwc->dr_mode) { 1190 case USB_DR_MODE_PERIPHERAL: 1191 dwc3_gadget_exit(dwc); 1192 break; 1193 case USB_DR_MODE_HOST: 1194 dwc3_host_exit(dwc); 1195 break; 1196 case USB_DR_MODE_OTG: 1197 dwc3_drd_exit(dwc); 1198 break; 1199 default: 1200 /* do nothing */ 1201 break; 1202 } 1203 } 1204 1205 static void dwc3_get_properties(struct dwc3 *dwc) 1206 { 1207 struct device *dev = dwc->dev; 1208 u8 lpm_nyet_threshold; 1209 u8 tx_de_emphasis; 1210 u8 hird_threshold; 1211 u8 rx_thr_num_pkt_prd; 1212 u8 rx_max_burst_prd; 1213 u8 tx_thr_num_pkt_prd; 1214 u8 tx_max_burst_prd; 1215 1216 /* default to highest possible threshold */ 1217 lpm_nyet_threshold = 0xff; 1218 1219 /* default to -3.5dB de-emphasis */ 1220 tx_de_emphasis = 1; 1221 1222 /* 1223 * default to assert utmi_sleep_n and use maximum allowed HIRD 1224 * threshold value of 0b1100 1225 */ 1226 hird_threshold = 12; 1227 1228 dwc->maximum_speed = usb_get_maximum_speed(dev); 1229 dwc->dr_mode = usb_get_dr_mode(dev); 1230 dwc->hsphy_mode = of_usb_get_phy_mode(dev->of_node); 1231 1232 dwc->sysdev_is_parent = device_property_read_bool(dev, 1233 "linux,sysdev_is_parent"); 1234 if (dwc->sysdev_is_parent) 1235 dwc->sysdev = dwc->dev->parent; 1236 else 1237 dwc->sysdev = dwc->dev; 1238 1239 dwc->has_lpm_erratum = device_property_read_bool(dev, 1240 "snps,has-lpm-erratum"); 1241 device_property_read_u8(dev, "snps,lpm-nyet-threshold", 1242 &lpm_nyet_threshold); 1243 dwc->is_utmi_l1_suspend = device_property_read_bool(dev, 1244 "snps,is-utmi-l1-suspend"); 1245 device_property_read_u8(dev, "snps,hird-threshold", 1246 &hird_threshold); 1247 dwc->usb3_lpm_capable = device_property_read_bool(dev, 1248 "snps,usb3_lpm_capable"); 1249 device_property_read_u8(dev, "snps,rx-thr-num-pkt-prd", 1250 &rx_thr_num_pkt_prd); 1251 device_property_read_u8(dev, "snps,rx-max-burst-prd", 1252 &rx_max_burst_prd); 1253 device_property_read_u8(dev, "snps,tx-thr-num-pkt-prd", 1254 &tx_thr_num_pkt_prd); 1255 device_property_read_u8(dev, "snps,tx-max-burst-prd", 1256 &tx_max_burst_prd); 1257 1258 dwc->disable_scramble_quirk = device_property_read_bool(dev, 1259 "snps,disable_scramble_quirk"); 1260 dwc->u2exit_lfps_quirk = device_property_read_bool(dev, 1261 "snps,u2exit_lfps_quirk"); 1262 dwc->u2ss_inp3_quirk = device_property_read_bool(dev, 1263 "snps,u2ss_inp3_quirk"); 1264 dwc->req_p1p2p3_quirk = device_property_read_bool(dev, 1265 "snps,req_p1p2p3_quirk"); 1266 dwc->del_p1p2p3_quirk = device_property_read_bool(dev, 1267 "snps,del_p1p2p3_quirk"); 1268 dwc->del_phy_power_chg_quirk = device_property_read_bool(dev, 1269 "snps,del_phy_power_chg_quirk"); 1270 dwc->lfps_filter_quirk = device_property_read_bool(dev, 1271 "snps,lfps_filter_quirk"); 1272 dwc->rx_detect_poll_quirk = device_property_read_bool(dev, 1273 "snps,rx_detect_poll_quirk"); 1274 dwc->dis_u3_susphy_quirk = device_property_read_bool(dev, 1275 "snps,dis_u3_susphy_quirk"); 1276 dwc->dis_u2_susphy_quirk = device_property_read_bool(dev, 1277 "snps,dis_u2_susphy_quirk"); 1278 dwc->dis_enblslpm_quirk = device_property_read_bool(dev, 1279 "snps,dis_enblslpm_quirk"); 1280 dwc->dis_rxdet_inp3_quirk = device_property_read_bool(dev, 1281 "snps,dis_rxdet_inp3_quirk"); 1282 dwc->dis_u2_freeclk_exists_quirk = device_property_read_bool(dev, 1283 "snps,dis-u2-freeclk-exists-quirk"); 1284 dwc->dis_del_phy_power_chg_quirk = device_property_read_bool(dev, 1285 "snps,dis-del-phy-power-chg-quirk"); 1286 dwc->dis_tx_ipgap_linecheck_quirk = device_property_read_bool(dev, 1287 "snps,dis-tx-ipgap-linecheck-quirk"); 1288 1289 dwc->tx_de_emphasis_quirk = device_property_read_bool(dev, 1290 "snps,tx_de_emphasis_quirk"); 1291 device_property_read_u8(dev, "snps,tx_de_emphasis", 1292 &tx_de_emphasis); 1293 device_property_read_string(dev, "snps,hsphy_interface", 1294 &dwc->hsphy_interface); 1295 device_property_read_u32(dev, "snps,quirk-frame-length-adjustment", 1296 &dwc->fladj); 1297 1298 dwc->dis_metastability_quirk = device_property_read_bool(dev, 1299 "snps,dis_metastability_quirk"); 1300 1301 dwc->lpm_nyet_threshold = lpm_nyet_threshold; 1302 dwc->tx_de_emphasis = tx_de_emphasis; 1303 1304 dwc->hird_threshold = hird_threshold 1305 | (dwc->is_utmi_l1_suspend << 4); 1306 1307 dwc->rx_thr_num_pkt_prd = rx_thr_num_pkt_prd; 1308 dwc->rx_max_burst_prd = rx_max_burst_prd; 1309 1310 dwc->tx_thr_num_pkt_prd = tx_thr_num_pkt_prd; 1311 dwc->tx_max_burst_prd = tx_max_burst_prd; 1312 1313 dwc->imod_interval = 0; 1314 } 1315 1316 /* check whether the core supports IMOD */ 1317 bool dwc3_has_imod(struct dwc3 *dwc) 1318 { 1319 return ((dwc3_is_usb3(dwc) && 1320 dwc->revision >= DWC3_REVISION_300A) || 1321 (dwc3_is_usb31(dwc) && 1322 dwc->revision >= DWC3_USB31_REVISION_120A)); 1323 } 1324 1325 static void dwc3_check_params(struct dwc3 *dwc) 1326 { 1327 struct device *dev = dwc->dev; 1328 1329 /* Check for proper value of imod_interval */ 1330 if (dwc->imod_interval && !dwc3_has_imod(dwc)) { 1331 dev_warn(dwc->dev, "Interrupt moderation not supported\n"); 1332 dwc->imod_interval = 0; 1333 } 1334 1335 /* 1336 * Workaround for STAR 9000961433 which affects only version 1337 * 3.00a of the DWC_usb3 core. This prevents the controller 1338 * interrupt from being masked while handling events. IMOD 1339 * allows us to work around this issue. Enable it for the 1340 * affected version. 1341 */ 1342 if (!dwc->imod_interval && 1343 (dwc->revision == DWC3_REVISION_300A)) 1344 dwc->imod_interval = 1; 1345 1346 /* Check the maximum_speed parameter */ 1347 switch (dwc->maximum_speed) { 1348 case USB_SPEED_LOW: 1349 case USB_SPEED_FULL: 1350 case USB_SPEED_HIGH: 1351 case USB_SPEED_SUPER: 1352 case USB_SPEED_SUPER_PLUS: 1353 break; 1354 default: 1355 dev_err(dev, "invalid maximum_speed parameter %d\n", 1356 dwc->maximum_speed); 1357 /* fall through */ 1358 case USB_SPEED_UNKNOWN: 1359 /* default to superspeed */ 1360 dwc->maximum_speed = USB_SPEED_SUPER; 1361 1362 /* 1363 * default to superspeed plus if we are capable. 1364 */ 1365 if (dwc3_is_usb31(dwc) && 1366 (DWC3_GHWPARAMS3_SSPHY_IFC(dwc->hwparams.hwparams3) == 1367 DWC3_GHWPARAMS3_SSPHY_IFC_GEN2)) 1368 dwc->maximum_speed = USB_SPEED_SUPER_PLUS; 1369 1370 break; 1371 } 1372 } 1373 1374 static int dwc3_probe(struct platform_device *pdev) 1375 { 1376 struct device *dev = &pdev->dev; 1377 struct resource *res, dwc_res; 1378 struct dwc3 *dwc; 1379 1380 int ret; 1381 1382 void __iomem *regs; 1383 1384 dwc = devm_kzalloc(dev, sizeof(*dwc), GFP_KERNEL); 1385 if (!dwc) 1386 return -ENOMEM; 1387 1388 dwc->clks = devm_kmemdup(dev, dwc3_core_clks, sizeof(dwc3_core_clks), 1389 GFP_KERNEL); 1390 if (!dwc->clks) 1391 return -ENOMEM; 1392 1393 dwc->dev = dev; 1394 1395 res = platform_get_resource(pdev, IORESOURCE_MEM, 0); 1396 if (!res) { 1397 dev_err(dev, "missing memory resource\n"); 1398 return -ENODEV; 1399 } 1400 1401 dwc->xhci_resources[0].start = res->start; 1402 dwc->xhci_resources[0].end = dwc->xhci_resources[0].start + 1403 DWC3_XHCI_REGS_END; 1404 dwc->xhci_resources[0].flags = res->flags; 1405 dwc->xhci_resources[0].name = res->name; 1406 1407 /* 1408 * Request memory region but exclude xHCI regs, 1409 * since it will be requested by the xhci-plat driver. 1410 */ 1411 dwc_res = *res; 1412 dwc_res.start += DWC3_GLOBALS_REGS_START; 1413 1414 regs = devm_ioremap_resource(dev, &dwc_res); 1415 if (IS_ERR(regs)) 1416 return PTR_ERR(regs); 1417 1418 dwc->regs = regs; 1419 dwc->regs_size = resource_size(&dwc_res); 1420 1421 dwc3_get_properties(dwc); 1422 1423 dwc->reset = devm_reset_control_get_optional_shared(dev, NULL); 1424 if (IS_ERR(dwc->reset)) 1425 return PTR_ERR(dwc->reset); 1426 1427 if (dev->of_node) { 1428 dwc->num_clks = ARRAY_SIZE(dwc3_core_clks); 1429 1430 ret = clk_bulk_get(dev, dwc->num_clks, dwc->clks); 1431 if (ret == -EPROBE_DEFER) 1432 return ret; 1433 /* 1434 * Clocks are optional, but new DT platforms should support all 1435 * clocks as required by the DT-binding. 1436 */ 1437 if (ret) 1438 dwc->num_clks = 0; 1439 } 1440 1441 ret = reset_control_deassert(dwc->reset); 1442 if (ret) 1443 goto put_clks; 1444 1445 ret = clk_bulk_prepare(dwc->num_clks, dwc->clks); 1446 if (ret) 1447 goto assert_reset; 1448 1449 ret = clk_bulk_enable(dwc->num_clks, dwc->clks); 1450 if (ret) 1451 goto unprepare_clks; 1452 1453 platform_set_drvdata(pdev, dwc); 1454 dwc3_cache_hwparams(dwc); 1455 1456 spin_lock_init(&dwc->lock); 1457 1458 pm_runtime_set_active(dev); 1459 pm_runtime_use_autosuspend(dev); 1460 pm_runtime_set_autosuspend_delay(dev, DWC3_DEFAULT_AUTOSUSPEND_DELAY); 1461 pm_runtime_enable(dev); 1462 ret = pm_runtime_get_sync(dev); 1463 if (ret < 0) 1464 goto err1; 1465 1466 pm_runtime_forbid(dev); 1467 1468 ret = dwc3_alloc_event_buffers(dwc, DWC3_EVENT_BUFFERS_SIZE); 1469 if (ret) { 1470 dev_err(dwc->dev, "failed to allocate event buffers\n"); 1471 ret = -ENOMEM; 1472 goto err2; 1473 } 1474 1475 ret = dwc3_get_dr_mode(dwc); 1476 if (ret) 1477 goto err3; 1478 1479 ret = dwc3_alloc_scratch_buffers(dwc); 1480 if (ret) 1481 goto err3; 1482 1483 ret = dwc3_core_init(dwc); 1484 if (ret) { 1485 dev_err(dev, "failed to initialize core\n"); 1486 goto err4; 1487 } 1488 1489 dwc3_check_params(dwc); 1490 1491 ret = dwc3_core_init_mode(dwc); 1492 if (ret) 1493 goto err5; 1494 1495 dwc3_debugfs_init(dwc); 1496 pm_runtime_put(dev); 1497 1498 return 0; 1499 1500 err5: 1501 dwc3_event_buffers_cleanup(dwc); 1502 1503 err4: 1504 dwc3_free_scratch_buffers(dwc); 1505 1506 err3: 1507 dwc3_free_event_buffers(dwc); 1508 1509 err2: 1510 pm_runtime_allow(&pdev->dev); 1511 1512 err1: 1513 pm_runtime_put_sync(&pdev->dev); 1514 pm_runtime_disable(&pdev->dev); 1515 1516 clk_bulk_disable(dwc->num_clks, dwc->clks); 1517 unprepare_clks: 1518 clk_bulk_unprepare(dwc->num_clks, dwc->clks); 1519 assert_reset: 1520 reset_control_assert(dwc->reset); 1521 put_clks: 1522 clk_bulk_put(dwc->num_clks, dwc->clks); 1523 1524 return ret; 1525 } 1526 1527 static int dwc3_remove(struct platform_device *pdev) 1528 { 1529 struct dwc3 *dwc = platform_get_drvdata(pdev); 1530 1531 pm_runtime_get_sync(&pdev->dev); 1532 1533 dwc3_debugfs_exit(dwc); 1534 dwc3_core_exit_mode(dwc); 1535 1536 dwc3_core_exit(dwc); 1537 dwc3_ulpi_exit(dwc); 1538 1539 pm_runtime_put_sync(&pdev->dev); 1540 pm_runtime_allow(&pdev->dev); 1541 pm_runtime_disable(&pdev->dev); 1542 1543 dwc3_free_event_buffers(dwc); 1544 dwc3_free_scratch_buffers(dwc); 1545 clk_bulk_put(dwc->num_clks, dwc->clks); 1546 1547 return 0; 1548 } 1549 1550 #ifdef CONFIG_PM 1551 static int dwc3_core_init_for_resume(struct dwc3 *dwc) 1552 { 1553 int ret; 1554 1555 ret = reset_control_deassert(dwc->reset); 1556 if (ret) 1557 return ret; 1558 1559 ret = clk_bulk_prepare(dwc->num_clks, dwc->clks); 1560 if (ret) 1561 goto assert_reset; 1562 1563 ret = clk_bulk_enable(dwc->num_clks, dwc->clks); 1564 if (ret) 1565 goto unprepare_clks; 1566 1567 ret = dwc3_core_init(dwc); 1568 if (ret) 1569 goto disable_clks; 1570 1571 return 0; 1572 1573 disable_clks: 1574 clk_bulk_disable(dwc->num_clks, dwc->clks); 1575 unprepare_clks: 1576 clk_bulk_unprepare(dwc->num_clks, dwc->clks); 1577 assert_reset: 1578 reset_control_assert(dwc->reset); 1579 1580 return ret; 1581 } 1582 1583 static int dwc3_suspend_common(struct dwc3 *dwc, pm_message_t msg) 1584 { 1585 unsigned long flags; 1586 u32 reg; 1587 1588 switch (dwc->current_dr_role) { 1589 case DWC3_GCTL_PRTCAP_DEVICE: 1590 spin_lock_irqsave(&dwc->lock, flags); 1591 dwc3_gadget_suspend(dwc); 1592 spin_unlock_irqrestore(&dwc->lock, flags); 1593 dwc3_core_exit(dwc); 1594 break; 1595 case DWC3_GCTL_PRTCAP_HOST: 1596 if (!PMSG_IS_AUTO(msg)) { 1597 dwc3_core_exit(dwc); 1598 break; 1599 } 1600 1601 /* Let controller to suspend HSPHY before PHY driver suspends */ 1602 if (dwc->dis_u2_susphy_quirk || 1603 dwc->dis_enblslpm_quirk) { 1604 reg = dwc3_readl(dwc->regs, DWC3_GUSB2PHYCFG(0)); 1605 reg |= DWC3_GUSB2PHYCFG_ENBLSLPM | 1606 DWC3_GUSB2PHYCFG_SUSPHY; 1607 dwc3_writel(dwc->regs, DWC3_GUSB2PHYCFG(0), reg); 1608 1609 /* Give some time for USB2 PHY to suspend */ 1610 usleep_range(5000, 6000); 1611 } 1612 1613 phy_pm_runtime_put_sync(dwc->usb2_generic_phy); 1614 phy_pm_runtime_put_sync(dwc->usb3_generic_phy); 1615 break; 1616 case DWC3_GCTL_PRTCAP_OTG: 1617 /* do nothing during runtime_suspend */ 1618 if (PMSG_IS_AUTO(msg)) 1619 break; 1620 1621 if (dwc->current_otg_role == DWC3_OTG_ROLE_DEVICE) { 1622 spin_lock_irqsave(&dwc->lock, flags); 1623 dwc3_gadget_suspend(dwc); 1624 spin_unlock_irqrestore(&dwc->lock, flags); 1625 } 1626 1627 dwc3_otg_exit(dwc); 1628 dwc3_core_exit(dwc); 1629 break; 1630 default: 1631 /* do nothing */ 1632 break; 1633 } 1634 1635 return 0; 1636 } 1637 1638 static int dwc3_resume_common(struct dwc3 *dwc, pm_message_t msg) 1639 { 1640 unsigned long flags; 1641 int ret; 1642 u32 reg; 1643 1644 switch (dwc->current_dr_role) { 1645 case DWC3_GCTL_PRTCAP_DEVICE: 1646 ret = dwc3_core_init_for_resume(dwc); 1647 if (ret) 1648 return ret; 1649 1650 dwc3_set_prtcap(dwc, DWC3_GCTL_PRTCAP_DEVICE); 1651 spin_lock_irqsave(&dwc->lock, flags); 1652 dwc3_gadget_resume(dwc); 1653 spin_unlock_irqrestore(&dwc->lock, flags); 1654 break; 1655 case DWC3_GCTL_PRTCAP_HOST: 1656 if (!PMSG_IS_AUTO(msg)) { 1657 ret = dwc3_core_init_for_resume(dwc); 1658 if (ret) 1659 return ret; 1660 dwc3_set_prtcap(dwc, DWC3_GCTL_PRTCAP_HOST); 1661 break; 1662 } 1663 /* Restore GUSB2PHYCFG bits that were modified in suspend */ 1664 reg = dwc3_readl(dwc->regs, DWC3_GUSB2PHYCFG(0)); 1665 if (dwc->dis_u2_susphy_quirk) 1666 reg &= ~DWC3_GUSB2PHYCFG_SUSPHY; 1667 1668 if (dwc->dis_enblslpm_quirk) 1669 reg &= ~DWC3_GUSB2PHYCFG_ENBLSLPM; 1670 1671 dwc3_writel(dwc->regs, DWC3_GUSB2PHYCFG(0), reg); 1672 1673 phy_pm_runtime_get_sync(dwc->usb2_generic_phy); 1674 phy_pm_runtime_get_sync(dwc->usb3_generic_phy); 1675 break; 1676 case DWC3_GCTL_PRTCAP_OTG: 1677 /* nothing to do on runtime_resume */ 1678 if (PMSG_IS_AUTO(msg)) 1679 break; 1680 1681 ret = dwc3_core_init(dwc); 1682 if (ret) 1683 return ret; 1684 1685 dwc3_set_prtcap(dwc, dwc->current_dr_role); 1686 1687 dwc3_otg_init(dwc); 1688 if (dwc->current_otg_role == DWC3_OTG_ROLE_HOST) { 1689 dwc3_otg_host_init(dwc); 1690 } else if (dwc->current_otg_role == DWC3_OTG_ROLE_DEVICE) { 1691 spin_lock_irqsave(&dwc->lock, flags); 1692 dwc3_gadget_resume(dwc); 1693 spin_unlock_irqrestore(&dwc->lock, flags); 1694 } 1695 1696 break; 1697 default: 1698 /* do nothing */ 1699 break; 1700 } 1701 1702 return 0; 1703 } 1704 1705 static int dwc3_runtime_checks(struct dwc3 *dwc) 1706 { 1707 switch (dwc->current_dr_role) { 1708 case DWC3_GCTL_PRTCAP_DEVICE: 1709 if (dwc->connected) 1710 return -EBUSY; 1711 break; 1712 case DWC3_GCTL_PRTCAP_HOST: 1713 default: 1714 /* do nothing */ 1715 break; 1716 } 1717 1718 return 0; 1719 } 1720 1721 static int dwc3_runtime_suspend(struct device *dev) 1722 { 1723 struct dwc3 *dwc = dev_get_drvdata(dev); 1724 int ret; 1725 1726 if (dwc3_runtime_checks(dwc)) 1727 return -EBUSY; 1728 1729 ret = dwc3_suspend_common(dwc, PMSG_AUTO_SUSPEND); 1730 if (ret) 1731 return ret; 1732 1733 device_init_wakeup(dev, true); 1734 1735 return 0; 1736 } 1737 1738 static int dwc3_runtime_resume(struct device *dev) 1739 { 1740 struct dwc3 *dwc = dev_get_drvdata(dev); 1741 int ret; 1742 1743 device_init_wakeup(dev, false); 1744 1745 ret = dwc3_resume_common(dwc, PMSG_AUTO_RESUME); 1746 if (ret) 1747 return ret; 1748 1749 switch (dwc->current_dr_role) { 1750 case DWC3_GCTL_PRTCAP_DEVICE: 1751 dwc3_gadget_process_pending_events(dwc); 1752 break; 1753 case DWC3_GCTL_PRTCAP_HOST: 1754 default: 1755 /* do nothing */ 1756 break; 1757 } 1758 1759 pm_runtime_mark_last_busy(dev); 1760 1761 return 0; 1762 } 1763 1764 static int dwc3_runtime_idle(struct device *dev) 1765 { 1766 struct dwc3 *dwc = dev_get_drvdata(dev); 1767 1768 switch (dwc->current_dr_role) { 1769 case DWC3_GCTL_PRTCAP_DEVICE: 1770 if (dwc3_runtime_checks(dwc)) 1771 return -EBUSY; 1772 break; 1773 case DWC3_GCTL_PRTCAP_HOST: 1774 default: 1775 /* do nothing */ 1776 break; 1777 } 1778 1779 pm_runtime_mark_last_busy(dev); 1780 pm_runtime_autosuspend(dev); 1781 1782 return 0; 1783 } 1784 #endif /* CONFIG_PM */ 1785 1786 #ifdef CONFIG_PM_SLEEP 1787 static int dwc3_suspend(struct device *dev) 1788 { 1789 struct dwc3 *dwc = dev_get_drvdata(dev); 1790 int ret; 1791 1792 ret = dwc3_suspend_common(dwc, PMSG_SUSPEND); 1793 if (ret) 1794 return ret; 1795 1796 pinctrl_pm_select_sleep_state(dev); 1797 1798 return 0; 1799 } 1800 1801 static int dwc3_resume(struct device *dev) 1802 { 1803 struct dwc3 *dwc = dev_get_drvdata(dev); 1804 int ret; 1805 1806 pinctrl_pm_select_default_state(dev); 1807 1808 ret = dwc3_resume_common(dwc, PMSG_RESUME); 1809 if (ret) 1810 return ret; 1811 1812 pm_runtime_disable(dev); 1813 pm_runtime_set_active(dev); 1814 pm_runtime_enable(dev); 1815 1816 return 0; 1817 } 1818 #endif /* CONFIG_PM_SLEEP */ 1819 1820 static const struct dev_pm_ops dwc3_dev_pm_ops = { 1821 SET_SYSTEM_SLEEP_PM_OPS(dwc3_suspend, dwc3_resume) 1822 SET_RUNTIME_PM_OPS(dwc3_runtime_suspend, dwc3_runtime_resume, 1823 dwc3_runtime_idle) 1824 }; 1825 1826 #ifdef CONFIG_OF 1827 static const struct of_device_id of_dwc3_match[] = { 1828 { 1829 .compatible = "snps,dwc3" 1830 }, 1831 { 1832 .compatible = "synopsys,dwc3" 1833 }, 1834 { }, 1835 }; 1836 MODULE_DEVICE_TABLE(of, of_dwc3_match); 1837 #endif 1838 1839 #ifdef CONFIG_ACPI 1840 1841 #define ACPI_ID_INTEL_BSW "808622B7" 1842 1843 static const struct acpi_device_id dwc3_acpi_match[] = { 1844 { ACPI_ID_INTEL_BSW, 0 }, 1845 { }, 1846 }; 1847 MODULE_DEVICE_TABLE(acpi, dwc3_acpi_match); 1848 #endif 1849 1850 static struct platform_driver dwc3_driver = { 1851 .probe = dwc3_probe, 1852 .remove = dwc3_remove, 1853 .driver = { 1854 .name = "dwc3", 1855 .of_match_table = of_match_ptr(of_dwc3_match), 1856 .acpi_match_table = ACPI_PTR(dwc3_acpi_match), 1857 .pm = &dwc3_dev_pm_ops, 1858 }, 1859 }; 1860 1861 module_platform_driver(dwc3_driver); 1862 1863 MODULE_ALIAS("platform:dwc3"); 1864 MODULE_AUTHOR("Felipe Balbi <balbi@ti.com>"); 1865 MODULE_LICENSE("GPL v2"); 1866 MODULE_DESCRIPTION("DesignWare USB3 DRD Controller Driver"); 1867