1 // SPDX-License-Identifier: GPL-2.0 2 /* 3 * host.c - ChipIdea USB host controller driver 4 * 5 * Copyright (c) 2012 Intel Corporation 6 * 7 * Author: Alexander Shishkin 8 */ 9 10 #include <linux/kernel.h> 11 #include <linux/io.h> 12 #include <linux/usb.h> 13 #include <linux/usb/hcd.h> 14 #include <linux/usb/chipidea.h> 15 #include <linux/regulator/consumer.h> 16 #include <linux/pinctrl/consumer.h> 17 18 #include "../host/ehci.h" 19 20 #include "ci.h" 21 #include "bits.h" 22 #include "host.h" 23 24 static struct hc_driver __read_mostly ci_ehci_hc_driver; 25 static int (*orig_bus_suspend)(struct usb_hcd *hcd); 26 27 struct ehci_ci_priv { 28 struct regulator *reg_vbus; 29 bool enabled; 30 }; 31 32 struct ci_hdrc_dma_aligned_buffer { 33 void *kmalloc_ptr; 34 void *old_xfer_buffer; 35 u8 data[]; 36 }; 37 38 static int ehci_ci_portpower(struct usb_hcd *hcd, int portnum, bool enable) 39 { 40 struct ehci_hcd *ehci = hcd_to_ehci(hcd); 41 struct ehci_ci_priv *priv = (struct ehci_ci_priv *)ehci->priv; 42 struct device *dev = hcd->self.controller; 43 struct ci_hdrc *ci = dev_get_drvdata(dev); 44 int ret = 0; 45 int port = HCS_N_PORTS(ehci->hcs_params); 46 47 if (priv->reg_vbus && enable != priv->enabled) { 48 if (port > 1) { 49 dev_warn(dev, 50 "Not support multi-port regulator control\n"); 51 return 0; 52 } 53 if (enable) 54 ret = regulator_enable(priv->reg_vbus); 55 else 56 ret = regulator_disable(priv->reg_vbus); 57 if (ret) { 58 dev_err(dev, 59 "Failed to %s vbus regulator, ret=%d\n", 60 enable ? "enable" : "disable", ret); 61 return ret; 62 } 63 priv->enabled = enable; 64 } 65 66 if (enable && (ci->platdata->phy_mode == USBPHY_INTERFACE_MODE_HSIC)) { 67 /* 68 * Marvell 28nm HSIC PHY requires forcing the port to HS mode. 69 * As HSIC is always HS, this should be safe for others. 70 */ 71 hw_port_test_set(ci, 5); 72 hw_port_test_set(ci, 0); 73 } 74 return 0; 75 }; 76 77 static int ehci_ci_reset(struct usb_hcd *hcd) 78 { 79 struct device *dev = hcd->self.controller; 80 struct ci_hdrc *ci = dev_get_drvdata(dev); 81 struct ehci_hcd *ehci = hcd_to_ehci(hcd); 82 int ret; 83 84 ret = ehci_setup(hcd); 85 if (ret) 86 return ret; 87 88 ehci->need_io_watchdog = 0; 89 90 if (ci->platdata->notify_event) { 91 ret = ci->platdata->notify_event(ci, 92 CI_HDRC_CONTROLLER_RESET_EVENT); 93 if (ret) 94 return ret; 95 } 96 97 ci_platform_configure(ci); 98 99 return ret; 100 } 101 102 static const struct ehci_driver_overrides ehci_ci_overrides = { 103 .extra_priv_size = sizeof(struct ehci_ci_priv), 104 .port_power = ehci_ci_portpower, 105 .reset = ehci_ci_reset, 106 }; 107 108 static irqreturn_t host_irq(struct ci_hdrc *ci) 109 { 110 return usb_hcd_irq(ci->irq, ci->hcd); 111 } 112 113 static int host_start(struct ci_hdrc *ci) 114 { 115 struct usb_hcd *hcd; 116 struct ehci_hcd *ehci; 117 struct ehci_ci_priv *priv; 118 int ret; 119 120 if (usb_disabled()) 121 return -ENODEV; 122 123 hcd = __usb_create_hcd(&ci_ehci_hc_driver, ci->dev->parent, 124 ci->dev, dev_name(ci->dev), NULL); 125 if (!hcd) 126 return -ENOMEM; 127 128 dev_set_drvdata(ci->dev, ci); 129 hcd->rsrc_start = ci->hw_bank.phys; 130 hcd->rsrc_len = ci->hw_bank.size; 131 hcd->regs = ci->hw_bank.abs; 132 hcd->has_tt = 1; 133 134 hcd->power_budget = ci->platdata->power_budget; 135 hcd->tpl_support = ci->platdata->tpl_support; 136 if (ci->phy || ci->usb_phy) { 137 hcd->skip_phy_initialization = 1; 138 if (ci->usb_phy) 139 hcd->usb_phy = ci->usb_phy; 140 } 141 142 ehci = hcd_to_ehci(hcd); 143 ehci->caps = ci->hw_bank.cap; 144 ehci->has_hostpc = ci->hw_bank.lpm; 145 ehci->has_tdi_phy_lpm = ci->hw_bank.lpm; 146 ehci->imx28_write_fix = ci->imx28_write_fix; 147 148 priv = (struct ehci_ci_priv *)ehci->priv; 149 priv->reg_vbus = NULL; 150 151 if (ci->platdata->reg_vbus && !ci_otg_is_fsm_mode(ci)) { 152 if (ci->platdata->flags & CI_HDRC_TURN_VBUS_EARLY_ON) { 153 ret = regulator_enable(ci->platdata->reg_vbus); 154 if (ret) { 155 dev_err(ci->dev, 156 "Failed to enable vbus regulator, ret=%d\n", 157 ret); 158 goto put_hcd; 159 } 160 } else { 161 priv->reg_vbus = ci->platdata->reg_vbus; 162 } 163 } 164 165 if (ci->platdata->pins_host) 166 pinctrl_select_state(ci->platdata->pctl, 167 ci->platdata->pins_host); 168 169 ci->hcd = hcd; 170 171 ret = usb_add_hcd(hcd, 0, 0); 172 if (ret) { 173 ci->hcd = NULL; 174 goto disable_reg; 175 } else { 176 struct usb_otg *otg = &ci->otg; 177 178 if (ci_otg_is_fsm_mode(ci)) { 179 otg->host = &hcd->self; 180 hcd->self.otg_port = 1; 181 } 182 183 if (ci->platdata->notify_event && 184 (ci->platdata->flags & CI_HDRC_IMX_IS_HSIC)) 185 ci->platdata->notify_event 186 (ci, CI_HDRC_IMX_HSIC_ACTIVE_EVENT); 187 } 188 189 return ret; 190 191 disable_reg: 192 if (ci->platdata->reg_vbus && !ci_otg_is_fsm_mode(ci) && 193 (ci->platdata->flags & CI_HDRC_TURN_VBUS_EARLY_ON)) 194 regulator_disable(ci->platdata->reg_vbus); 195 put_hcd: 196 usb_put_hcd(hcd); 197 198 return ret; 199 } 200 201 static void host_stop(struct ci_hdrc *ci) 202 { 203 struct usb_hcd *hcd = ci->hcd; 204 205 if (hcd) { 206 if (ci->platdata->notify_event) 207 ci->platdata->notify_event(ci, 208 CI_HDRC_CONTROLLER_STOPPED_EVENT); 209 usb_remove_hcd(hcd); 210 ci->role = CI_ROLE_END; 211 synchronize_irq(ci->irq); 212 usb_put_hcd(hcd); 213 if (ci->platdata->reg_vbus && !ci_otg_is_fsm_mode(ci) && 214 (ci->platdata->flags & CI_HDRC_TURN_VBUS_EARLY_ON)) 215 regulator_disable(ci->platdata->reg_vbus); 216 } 217 ci->hcd = NULL; 218 ci->otg.host = NULL; 219 220 if (ci->platdata->pins_host && ci->platdata->pins_default) 221 pinctrl_select_state(ci->platdata->pctl, 222 ci->platdata->pins_default); 223 } 224 225 226 void ci_hdrc_host_destroy(struct ci_hdrc *ci) 227 { 228 if (ci->role == CI_ROLE_HOST && ci->hcd) 229 host_stop(ci); 230 } 231 232 /* The below code is based on tegra ehci driver */ 233 static int ci_ehci_hub_control( 234 struct usb_hcd *hcd, 235 u16 typeReq, 236 u16 wValue, 237 u16 wIndex, 238 char *buf, 239 u16 wLength 240 ) 241 { 242 struct ehci_hcd *ehci = hcd_to_ehci(hcd); 243 u32 __iomem *status_reg; 244 u32 temp; 245 unsigned long flags; 246 int retval = 0; 247 bool done = false; 248 struct device *dev = hcd->self.controller; 249 struct ci_hdrc *ci = dev_get_drvdata(dev); 250 251 status_reg = &ehci->regs->port_status[(wIndex & 0xff) - 1]; 252 253 spin_lock_irqsave(&ehci->lock, flags); 254 255 if (ci->platdata->hub_control) { 256 retval = ci->platdata->hub_control(ci, typeReq, wValue, wIndex, 257 buf, wLength, &done, &flags); 258 if (done) 259 goto done; 260 } 261 262 if (typeReq == SetPortFeature && wValue == USB_PORT_FEAT_SUSPEND) { 263 temp = ehci_readl(ehci, status_reg); 264 if ((temp & PORT_PE) == 0 || (temp & PORT_RESET) != 0) { 265 retval = -EPIPE; 266 goto done; 267 } 268 269 temp &= ~(PORT_RWC_BITS | PORT_WKCONN_E); 270 temp |= PORT_WKDISC_E | PORT_WKOC_E; 271 ehci_writel(ehci, temp | PORT_SUSPEND, status_reg); 272 273 /* 274 * If a transaction is in progress, there may be a delay in 275 * suspending the port. Poll until the port is suspended. 276 */ 277 if (ehci_handshake(ehci, status_reg, PORT_SUSPEND, 278 PORT_SUSPEND, 5000)) 279 ehci_err(ehci, "timeout waiting for SUSPEND\n"); 280 281 if (ci->platdata->flags & CI_HDRC_IMX_IS_HSIC) { 282 if (ci->platdata->notify_event) 283 ci->platdata->notify_event(ci, 284 CI_HDRC_IMX_HSIC_SUSPEND_EVENT); 285 286 temp = ehci_readl(ehci, status_reg); 287 temp &= ~(PORT_WKDISC_E | PORT_WKCONN_E); 288 ehci_writel(ehci, temp, status_reg); 289 } 290 291 set_bit((wIndex & 0xff) - 1, &ehci->suspended_ports); 292 goto done; 293 } 294 295 /* 296 * After resume has finished, it needs do some post resume 297 * operation for some SoCs. 298 */ 299 else if (typeReq == ClearPortFeature && 300 wValue == USB_PORT_FEAT_C_SUSPEND) { 301 /* Make sure the resume has finished, it should be finished */ 302 if (ehci_handshake(ehci, status_reg, PORT_RESUME, 0, 25000)) 303 ehci_err(ehci, "timeout waiting for resume\n"); 304 } 305 306 spin_unlock_irqrestore(&ehci->lock, flags); 307 308 /* Handle the hub control events here */ 309 return ehci_hub_control(hcd, typeReq, wValue, wIndex, buf, wLength); 310 done: 311 spin_unlock_irqrestore(&ehci->lock, flags); 312 return retval; 313 } 314 static int ci_ehci_bus_suspend(struct usb_hcd *hcd) 315 { 316 struct ehci_hcd *ehci = hcd_to_ehci(hcd); 317 struct device *dev = hcd->self.controller; 318 struct ci_hdrc *ci = dev_get_drvdata(dev); 319 int port; 320 u32 tmp; 321 322 int ret = orig_bus_suspend(hcd); 323 324 if (ret) 325 return ret; 326 327 port = HCS_N_PORTS(ehci->hcs_params); 328 while (port--) { 329 u32 __iomem *reg = &ehci->regs->port_status[port]; 330 u32 portsc = ehci_readl(ehci, reg); 331 332 if (portsc & PORT_CONNECT) { 333 /* 334 * For chipidea, the resume signal will be ended 335 * automatically, so for remote wakeup case, the 336 * usbcmd.rs may not be set before the resume has 337 * ended if other resume paths consumes too much 338 * time (~24ms), in that case, the SOF will not 339 * send out within 3ms after resume ends, then the 340 * high speed device will enter full speed mode. 341 */ 342 343 tmp = ehci_readl(ehci, &ehci->regs->command); 344 tmp |= CMD_RUN; 345 ehci_writel(ehci, tmp, &ehci->regs->command); 346 /* 347 * It needs a short delay between set RS bit and PHCD. 348 */ 349 usleep_range(150, 200); 350 /* 351 * Need to clear WKCN and WKOC for imx HSIC, 352 * otherwise, there will be wakeup event. 353 */ 354 if (ci->platdata->flags & CI_HDRC_IMX_IS_HSIC) { 355 tmp = ehci_readl(ehci, reg); 356 tmp &= ~(PORT_WKDISC_E | PORT_WKCONN_E); 357 ehci_writel(ehci, tmp, reg); 358 } 359 360 break; 361 } 362 } 363 364 return 0; 365 } 366 367 static void ci_hdrc_free_dma_aligned_buffer(struct urb *urb) 368 { 369 struct ci_hdrc_dma_aligned_buffer *temp; 370 size_t length; 371 372 if (!(urb->transfer_flags & URB_ALIGNED_TEMP_BUFFER)) 373 return; 374 375 temp = container_of(urb->transfer_buffer, 376 struct ci_hdrc_dma_aligned_buffer, data); 377 378 if (usb_urb_dir_in(urb)) { 379 if (usb_pipeisoc(urb->pipe)) 380 length = urb->transfer_buffer_length; 381 else 382 length = urb->actual_length; 383 384 memcpy(temp->old_xfer_buffer, temp->data, length); 385 } 386 urb->transfer_buffer = temp->old_xfer_buffer; 387 kfree(temp->kmalloc_ptr); 388 389 urb->transfer_flags &= ~URB_ALIGNED_TEMP_BUFFER; 390 } 391 392 static int ci_hdrc_alloc_dma_aligned_buffer(struct urb *urb, gfp_t mem_flags) 393 { 394 struct ci_hdrc_dma_aligned_buffer *temp, *kmalloc_ptr; 395 const unsigned int ci_hdrc_usb_dma_align = 32; 396 size_t kmalloc_size; 397 398 if (urb->num_sgs || urb->sg || urb->transfer_buffer_length == 0 || 399 !((uintptr_t)urb->transfer_buffer & (ci_hdrc_usb_dma_align - 1))) 400 return 0; 401 402 /* Allocate a buffer with enough padding for alignment */ 403 kmalloc_size = urb->transfer_buffer_length + 404 sizeof(struct ci_hdrc_dma_aligned_buffer) + 405 ci_hdrc_usb_dma_align - 1; 406 407 kmalloc_ptr = kmalloc(kmalloc_size, mem_flags); 408 if (!kmalloc_ptr) 409 return -ENOMEM; 410 411 /* Position our struct dma_aligned_buffer such that data is aligned */ 412 temp = PTR_ALIGN(kmalloc_ptr + 1, ci_hdrc_usb_dma_align) - 1; 413 temp->kmalloc_ptr = kmalloc_ptr; 414 temp->old_xfer_buffer = urb->transfer_buffer; 415 if (usb_urb_dir_out(urb)) 416 memcpy(temp->data, urb->transfer_buffer, 417 urb->transfer_buffer_length); 418 urb->transfer_buffer = temp->data; 419 420 urb->transfer_flags |= URB_ALIGNED_TEMP_BUFFER; 421 422 return 0; 423 } 424 425 static int ci_hdrc_map_urb_for_dma(struct usb_hcd *hcd, struct urb *urb, 426 gfp_t mem_flags) 427 { 428 int ret; 429 430 ret = ci_hdrc_alloc_dma_aligned_buffer(urb, mem_flags); 431 if (ret) 432 return ret; 433 434 ret = usb_hcd_map_urb_for_dma(hcd, urb, mem_flags); 435 if (ret) 436 ci_hdrc_free_dma_aligned_buffer(urb); 437 438 return ret; 439 } 440 441 static void ci_hdrc_unmap_urb_for_dma(struct usb_hcd *hcd, struct urb *urb) 442 { 443 usb_hcd_unmap_urb_for_dma(hcd, urb); 444 ci_hdrc_free_dma_aligned_buffer(urb); 445 } 446 447 int ci_hdrc_host_init(struct ci_hdrc *ci) 448 { 449 struct ci_role_driver *rdrv; 450 451 if (!hw_read(ci, CAP_DCCPARAMS, DCCPARAMS_HC)) 452 return -ENXIO; 453 454 rdrv = devm_kzalloc(ci->dev, sizeof(struct ci_role_driver), GFP_KERNEL); 455 if (!rdrv) 456 return -ENOMEM; 457 458 rdrv->start = host_start; 459 rdrv->stop = host_stop; 460 rdrv->irq = host_irq; 461 rdrv->name = "host"; 462 ci->roles[CI_ROLE_HOST] = rdrv; 463 464 if (ci->platdata->flags & CI_HDRC_REQUIRES_ALIGNED_DMA) { 465 ci_ehci_hc_driver.map_urb_for_dma = ci_hdrc_map_urb_for_dma; 466 ci_ehci_hc_driver.unmap_urb_for_dma = ci_hdrc_unmap_urb_for_dma; 467 } 468 469 return 0; 470 } 471 472 void ci_hdrc_host_driver_init(void) 473 { 474 ehci_init_driver(&ci_ehci_hc_driver, &ehci_ci_overrides); 475 orig_bus_suspend = ci_ehci_hc_driver.bus_suspend; 476 ci_ehci_hc_driver.bus_suspend = ci_ehci_bus_suspend; 477 ci_ehci_hc_driver.hub_control = ci_ehci_hub_control; 478 } 479