1 /* SPDX-License-Identifier: GPL-2.0 */ 2 /* 3 * USBSS device controller driver header file 4 * 5 * Copyright (C) 2018-2019 Cadence. 6 * Copyright (C) 2017-2018 NXP 7 * 8 * Author: Pawel Laszczak <pawell@cadence.com> 9 * Pawel Jez <pjez@cadence.com> 10 * Peter Chen <peter.chen@nxp.com> 11 */ 12 #ifndef __LINUX_CDNS3_GADGET 13 #define __LINUX_CDNS3_GADGET 14 #include <linux/usb/gadget.h> 15 #include <linux/dma-direction.h> 16 17 /* 18 * USBSS-DEV register interface. 19 * This corresponds to the USBSS Device Controller Interface 20 */ 21 22 /** 23 * struct cdns3_usb_regs - device controller registers. 24 * @usb_conf: Global Configuration. 25 * @usb_sts: Global Status. 26 * @usb_cmd: Global Command. 27 * @usb_itpn: ITP/SOF number. 28 * @usb_lpm: Global Command. 29 * @usb_ien: USB Interrupt Enable. 30 * @usb_ists: USB Interrupt Status. 31 * @ep_sel: Endpoint Select. 32 * @ep_traddr: Endpoint Transfer Ring Address. 33 * @ep_cfg: Endpoint Configuration. 34 * @ep_cmd: Endpoint Command. 35 * @ep_sts: Endpoint Status. 36 * @ep_sts_sid: Endpoint Status. 37 * @ep_sts_en: Endpoint Status Enable. 38 * @drbl: Doorbell. 39 * @ep_ien: EP Interrupt Enable. 40 * @ep_ists: EP Interrupt Status. 41 * @usb_pwr: Global Power Configuration. 42 * @usb_conf2: Global Configuration 2. 43 * @usb_cap1: Capability 1. 44 * @usb_cap2: Capability 2. 45 * @usb_cap3: Capability 3. 46 * @usb_cap4: Capability 4. 47 * @usb_cap5: Capability 5. 48 * @usb_cap6: Capability 6. 49 * @usb_cpkt1: Custom Packet 1. 50 * @usb_cpkt2: Custom Packet 2. 51 * @usb_cpkt3: Custom Packet 3. 52 * @ep_dma_ext_addr: Upper address for DMA operations. 53 * @buf_addr: Address for On-chip Buffer operations. 54 * @buf_data: Data for On-chip Buffer operations. 55 * @buf_ctrl: On-chip Buffer Access Control. 56 * @dtrans: DMA Transfer Mode. 57 * @tdl_from_trb: Source of TD Configuration. 58 * @tdl_beh: TDL Behavior Configuration. 59 * @ep_tdl: Endpoint TDL. 60 * @tdl_beh2: TDL Behavior 2 Configuration. 61 * @dma_adv_td: DMA Advance TD Configuration. 62 * @reserved1: Reserved. 63 * @cfg_regs: Configuration. 64 * @reserved2: Reserved. 65 * @dma_axi_ctrl: AXI Control. 66 * @dma_axi_id: AXI ID register. 67 * @dma_axi_cap: AXI Capability. 68 * @dma_axi_ctrl0: AXI Control 0. 69 * @dma_axi_ctrl1: AXI Control 1. 70 */ 71 struct cdns3_usb_regs { 72 __le32 usb_conf; 73 __le32 usb_sts; 74 __le32 usb_cmd; 75 __le32 usb_itpn; 76 __le32 usb_lpm; 77 __le32 usb_ien; 78 __le32 usb_ists; 79 __le32 ep_sel; 80 __le32 ep_traddr; 81 __le32 ep_cfg; 82 __le32 ep_cmd; 83 __le32 ep_sts; 84 __le32 ep_sts_sid; 85 __le32 ep_sts_en; 86 __le32 drbl; 87 __le32 ep_ien; 88 __le32 ep_ists; 89 __le32 usb_pwr; 90 __le32 usb_conf2; 91 __le32 usb_cap1; 92 __le32 usb_cap2; 93 __le32 usb_cap3; 94 __le32 usb_cap4; 95 __le32 usb_cap5; 96 __le32 usb_cap6; 97 __le32 usb_cpkt1; 98 __le32 usb_cpkt2; 99 __le32 usb_cpkt3; 100 __le32 ep_dma_ext_addr; 101 __le32 buf_addr; 102 __le32 buf_data; 103 __le32 buf_ctrl; 104 __le32 dtrans; 105 __le32 tdl_from_trb; 106 __le32 tdl_beh; 107 __le32 ep_tdl; 108 __le32 tdl_beh2; 109 __le32 dma_adv_td; 110 __le32 reserved1[26]; 111 __le32 cfg_reg1; 112 __le32 dbg_link1; 113 __le32 dbg_link2; 114 __le32 cfg_regs[74]; 115 __le32 reserved2[51]; 116 __le32 dma_axi_ctrl; 117 __le32 dma_axi_id; 118 __le32 dma_axi_cap; 119 __le32 dma_axi_ctrl0; 120 __le32 dma_axi_ctrl1; 121 }; 122 123 /* USB_CONF - bitmasks */ 124 /* Reset USB device configuration. */ 125 #define USB_CONF_CFGRST BIT(0) 126 /* Set Configuration. */ 127 #define USB_CONF_CFGSET BIT(1) 128 /* Disconnect USB device in SuperSpeed. */ 129 #define USB_CONF_USB3DIS BIT(3) 130 /* Disconnect USB device in HS/FS */ 131 #define USB_CONF_USB2DIS BIT(4) 132 /* Little Endian access - default */ 133 #define USB_CONF_LENDIAN BIT(5) 134 /* 135 * Big Endian access. Driver assume that byte order for 136 * SFRs access always is as Little Endian so this bit 137 * is not used. 138 */ 139 #define USB_CONF_BENDIAN BIT(6) 140 /* Device software reset. */ 141 #define USB_CONF_SWRST BIT(7) 142 /* Singular DMA transfer mode. Only for VER < DEV_VER_V3*/ 143 #define USB_CONF_DSING BIT(8) 144 /* Multiple DMA transfers mode. Only for VER < DEV_VER_V3 */ 145 #define USB_CONF_DMULT BIT(9) 146 /* DMA clock turn-off enable. */ 147 #define USB_CONF_DMAOFFEN BIT(10) 148 /* DMA clock turn-off disable. */ 149 #define USB_CONF_DMAOFFDS BIT(11) 150 /* Clear Force Full Speed. */ 151 #define USB_CONF_CFORCE_FS BIT(12) 152 /* Set Force Full Speed. */ 153 #define USB_CONF_SFORCE_FS BIT(13) 154 /* Device enable. */ 155 #define USB_CONF_DEVEN BIT(14) 156 /* Device disable. */ 157 #define USB_CONF_DEVDS BIT(15) 158 /* L1 LPM state entry enable (used in HS/FS mode). */ 159 #define USB_CONF_L1EN BIT(16) 160 /* L1 LPM state entry disable (used in HS/FS mode). */ 161 #define USB_CONF_L1DS BIT(17) 162 /* USB 2.0 clock gate disable. */ 163 #define USB_CONF_CLK2OFFEN BIT(18) 164 /* USB 2.0 clock gate enable. */ 165 #define USB_CONF_CLK2OFFDS BIT(19) 166 /* L0 LPM state entry request (used in HS/FS mode). */ 167 #define USB_CONF_LGO_L0 BIT(20) 168 /* USB 3.0 clock gate disable. */ 169 #define USB_CONF_CLK3OFFEN BIT(21) 170 /* USB 3.0 clock gate enable. */ 171 #define USB_CONF_CLK3OFFDS BIT(22) 172 /* Bit 23 is reserved*/ 173 /* U1 state entry enable (used in SS mode). */ 174 #define USB_CONF_U1EN BIT(24) 175 /* U1 state entry disable (used in SS mode). */ 176 #define USB_CONF_U1DS BIT(25) 177 /* U2 state entry enable (used in SS mode). */ 178 #define USB_CONF_U2EN BIT(26) 179 /* U2 state entry disable (used in SS mode). */ 180 #define USB_CONF_U2DS BIT(27) 181 /* U0 state entry request (used in SS mode). */ 182 #define USB_CONF_LGO_U0 BIT(28) 183 /* U1 state entry request (used in SS mode). */ 184 #define USB_CONF_LGO_U1 BIT(29) 185 /* U2 state entry request (used in SS mode). */ 186 #define USB_CONF_LGO_U2 BIT(30) 187 /* SS.Inactive state entry request (used in SS mode) */ 188 #define USB_CONF_LGO_SSINACT BIT(31) 189 190 /* USB_STS - bitmasks */ 191 /* 192 * Configuration status. 193 * 1 - device is in the configured state. 194 * 0 - device is not configured. 195 */ 196 #define USB_STS_CFGSTS_MASK BIT(0) 197 #define USB_STS_CFGSTS(p) ((p) & USB_STS_CFGSTS_MASK) 198 /* 199 * On-chip memory overflow. 200 * 0 - On-chip memory status OK. 201 * 1 - On-chip memory overflow. 202 */ 203 #define USB_STS_OV_MASK BIT(1) 204 #define USB_STS_OV(p) ((p) & USB_STS_OV_MASK) 205 /* 206 * SuperSpeed connection status. 207 * 0 - USB in SuperSpeed mode disconnected. 208 * 1 - USB in SuperSpeed mode connected. 209 */ 210 #define USB_STS_USB3CONS_MASK BIT(2) 211 #define USB_STS_USB3CONS(p) ((p) & USB_STS_USB3CONS_MASK) 212 /* 213 * DMA transfer configuration status. 214 * 0 - single request. 215 * 1 - multiple TRB chain 216 * Supported only for controller version < DEV_VER_V3 217 */ 218 #define USB_STS_DTRANS_MASK BIT(3) 219 #define USB_STS_DTRANS(p) ((p) & USB_STS_DTRANS_MASK) 220 /* 221 * Device speed. 222 * 0 - Undefined (value after reset). 223 * 1 - Low speed 224 * 2 - Full speed 225 * 3 - High speed 226 * 4 - Super speed 227 */ 228 #define USB_STS_USBSPEED_MASK GENMASK(6, 4) 229 #define USB_STS_USBSPEED(p) (((p) & USB_STS_USBSPEED_MASK) >> 4) 230 #define USB_STS_LS (0x1 << 4) 231 #define USB_STS_FS (0x2 << 4) 232 #define USB_STS_HS (0x3 << 4) 233 #define USB_STS_SS (0x4 << 4) 234 #define DEV_UNDEFSPEED(p) (((p) & USB_STS_USBSPEED_MASK) == (0x0 << 4)) 235 #define DEV_LOWSPEED(p) (((p) & USB_STS_USBSPEED_MASK) == USB_STS_LS) 236 #define DEV_FULLSPEED(p) (((p) & USB_STS_USBSPEED_MASK) == USB_STS_FS) 237 #define DEV_HIGHSPEED(p) (((p) & USB_STS_USBSPEED_MASK) == USB_STS_HS) 238 #define DEV_SUPERSPEED(p) (((p) & USB_STS_USBSPEED_MASK) == USB_STS_SS) 239 /* 240 * Endianness for SFR access. 241 * 0 - Little Endian order (default after hardware reset). 242 * 1 - Big Endian order 243 */ 244 #define USB_STS_ENDIAN_MASK BIT(7) 245 #define USB_STS_ENDIAN(p) ((p) & USB_STS_ENDIAN_MASK) 246 /* 247 * HS/FS clock turn-off status. 248 * 0 - hsfs clock is always on. 249 * 1 - hsfs clock turn-off in L2 (HS/FS mode) is enabled 250 * (default after hardware reset). 251 */ 252 #define USB_STS_CLK2OFF_MASK BIT(8) 253 #define USB_STS_CLK2OFF(p) ((p) & USB_STS_CLK2OFF_MASK) 254 /* 255 * PCLK clock turn-off status. 256 * 0 - pclk clock is always on. 257 * 1 - pclk clock turn-off in U3 (SS mode) is enabled 258 * (default after hardware reset). 259 */ 260 #define USB_STS_CLK3OFF_MASK BIT(9) 261 #define USB_STS_CLK3OFF(p) ((p) & USB_STS_CLK3OFF_MASK) 262 /* 263 * Controller in reset state. 264 * 0 - Internal reset is active. 265 * 1 - Internal reset is not active and controller is fully operational. 266 */ 267 #define USB_STS_IN_RST_MASK BIT(10) 268 #define USB_STS_IN_RST(p) ((p) & USB_STS_IN_RST_MASK) 269 /* 270 * Status of the "TDL calculation basing on TRB" feature. 271 * 0 - disabled 272 * 1 - enabled 273 * Supported only for DEV_VER_V2 controller version. 274 */ 275 #define USB_STS_TDL_TRB_ENABLED BIT(11) 276 /* 277 * Device enable Status. 278 * 0 - USB device is disabled (VBUS input is disconnected from internal logic). 279 * 1 - USB device is enabled (VBUS input is connected to the internal logic). 280 */ 281 #define USB_STS_DEVS_MASK BIT(14) 282 #define USB_STS_DEVS(p) ((p) & USB_STS_DEVS_MASK) 283 /* 284 * Address status. 285 * 0 - USB device is default state. 286 * 1 - USB device is at least in address state. 287 */ 288 #define USB_STS_ADDRESSED_MASK BIT(15) 289 #define USB_STS_ADDRESSED(p) ((p) & USB_STS_ADDRESSED_MASK) 290 /* 291 * L1 LPM state enable status (used in HS/FS mode). 292 * 0 - Entering to L1 LPM state disabled. 293 * 1 - Entering to L1 LPM state enabled. 294 */ 295 #define USB_STS_L1ENS_MASK BIT(16) 296 #define USB_STS_L1ENS(p) ((p) & USB_STS_L1ENS_MASK) 297 /* 298 * Internal VBUS connection status (used both in HS/FS and SS mode). 299 * 0 - internal VBUS is not detected. 300 * 1 - internal VBUS is detected. 301 */ 302 #define USB_STS_VBUSS_MASK BIT(17) 303 #define USB_STS_VBUSS(p) ((p) & USB_STS_VBUSS_MASK) 304 /* 305 * HS/FS LPM state (used in FS/HS mode). 306 * 0 - L0 State 307 * 1 - L1 State 308 * 2 - L2 State 309 * 3 - L3 State 310 */ 311 #define USB_STS_LPMST_MASK GENMASK(19, 18) 312 #define DEV_L0_STATE(p) (((p) & USB_STS_LPMST_MASK) == (0x0 << 18)) 313 #define DEV_L1_STATE(p) (((p) & USB_STS_LPMST_MASK) == (0x1 << 18)) 314 #define DEV_L2_STATE(p) (((p) & USB_STS_LPMST_MASK) == (0x2 << 18)) 315 #define DEV_L3_STATE(p) (((p) & USB_STS_LPMST_MASK) == (0x3 << 18)) 316 /* 317 * Disable HS status (used in FS/HS mode). 318 * 0 - the disconnect bit for HS/FS mode is set . 319 * 1 - the disconnect bit for HS/FS mode is not set. 320 */ 321 #define USB_STS_USB2CONS_MASK BIT(20) 322 #define USB_STS_USB2CONS(p) ((p) & USB_STS_USB2CONS_MASK) 323 /* 324 * HS/FS mode connection status (used in FS/HS mode). 325 * 0 - High Speed operations in USB2.0 (FS/HS) mode not disabled. 326 * 1 - High Speed operations in USB2.0 (FS/HS). 327 */ 328 #define USB_STS_DISABLE_HS_MASK BIT(21) 329 #define USB_STS_DISABLE_HS(p) ((p) & USB_STS_DISABLE_HS_MASK) 330 /* 331 * U1 state enable status (used in SS mode). 332 * 0 - Entering to U1 state disabled. 333 * 1 - Entering to U1 state enabled. 334 */ 335 #define USB_STS_U1ENS_MASK BIT(24) 336 #define USB_STS_U1ENS(p) ((p) & USB_STS_U1ENS_MASK) 337 /* 338 * U2 state enable status (used in SS mode). 339 * 0 - Entering to U2 state disabled. 340 * 1 - Entering to U2 state enabled. 341 */ 342 #define USB_STS_U2ENS_MASK BIT(25) 343 #define USB_STS_U2ENS(p) ((p) & USB_STS_U2ENS_MASK) 344 /* 345 * SuperSpeed Link LTSSM state. This field reflects USBSS-DEV current 346 * SuperSpeed link state 347 */ 348 #define USB_STS_LST_MASK GENMASK(29, 26) 349 #define DEV_LST_U0 (((p) & USB_STS_LST_MASK) == (0x0 << 26)) 350 #define DEV_LST_U1 (((p) & USB_STS_LST_MASK) == (0x1 << 26)) 351 #define DEV_LST_U2 (((p) & USB_STS_LST_MASK) == (0x2 << 26)) 352 #define DEV_LST_U3 (((p) & USB_STS_LST_MASK) == (0x3 << 26)) 353 #define DEV_LST_DISABLED (((p) & USB_STS_LST_MASK) == (0x4 << 26)) 354 #define DEV_LST_RXDETECT (((p) & USB_STS_LST_MASK) == (0x5 << 26)) 355 #define DEV_LST_INACTIVE (((p) & USB_STS_LST_MASK) == (0x6 << 26)) 356 #define DEV_LST_POLLING (((p) & USB_STS_LST_MASK) == (0x7 << 26)) 357 #define DEV_LST_RECOVERY (((p) & USB_STS_LST_MASK) == (0x8 << 26)) 358 #define DEV_LST_HOT_RESET (((p) & USB_STS_LST_MASK) == (0x9 << 26)) 359 #define DEV_LST_COMP_MODE (((p) & USB_STS_LST_MASK) == (0xa << 26)) 360 #define DEV_LST_LB_STATE (((p) & USB_STS_LST_MASK) == (0xb << 26)) 361 /* 362 * DMA clock turn-off status. 363 * 0 - DMA clock is always on (default after hardware reset). 364 * 1 - DMA clock turn-off in U1, U2 and U3 (SS mode) is enabled. 365 */ 366 #define USB_STS_DMAOFF_MASK BIT(30) 367 #define USB_STS_DMAOFF(p) ((p) & USB_STS_DMAOFF_MASK) 368 /* 369 * SFR Endian status. 370 * 0 - Little Endian order (default after hardware reset). 371 * 1 - Big Endian order. 372 */ 373 #define USB_STS_ENDIAN2_MASK BIT(31) 374 #define USB_STS_ENDIAN2(p) ((p) & USB_STS_ENDIAN2_MASK) 375 376 /* USB_CMD - bitmasks */ 377 /* Set Function Address */ 378 #define USB_CMD_SET_ADDR BIT(0) 379 /* 380 * Function Address This field is saved to the device only when the field 381 * SET_ADDR is set '1 ' during write to USB_CMD register. 382 * Software is responsible for entering the address of the device during 383 * SET_ADDRESS request service. This field should be set immediately after 384 * the SETUP packet is decoded, and prior to confirmation of the status phase 385 */ 386 #define USB_CMD_FADDR_MASK GENMASK(7, 1) 387 #define USB_CMD_FADDR(p) (((p) << 1) & USB_CMD_FADDR_MASK) 388 /* Send Function Wake Device Notification TP (used only in SS mode). */ 389 #define USB_CMD_SDNFW BIT(8) 390 /* Set Test Mode (used only in HS/FS mode). */ 391 #define USB_CMD_STMODE BIT(9) 392 /* Test mode selector (used only in HS/FS mode) */ 393 #define USB_STS_TMODE_SEL_MASK GENMASK(11, 10) 394 #define USB_STS_TMODE_SEL(p) (((p) << 10) & USB_STS_TMODE_SEL_MASK) 395 /* 396 * Send Latency Tolerance Message Device Notification TP (used only 397 * in SS mode). 398 */ 399 #define USB_CMD_SDNLTM BIT(12) 400 /* Send Custom Transaction Packet (used only in SS mode) */ 401 #define USB_CMD_SPKT BIT(13) 402 /*Device Notification 'Function Wake' - Interface value (only in SS mode. */ 403 #define USB_CMD_DNFW_INT_MASK GENMASK(23, 16) 404 #define USB_STS_DNFW_INT(p) (((p) << 16) & USB_CMD_DNFW_INT_MASK) 405 /* 406 * Device Notification 'Latency Tolerance Message' -373 BELT value [7:0] 407 * (used only in SS mode). 408 */ 409 #define USB_CMD_DNLTM_BELT_MASK GENMASK(27, 16) 410 #define USB_STS_DNLTM_BELT(p) (((p) << 16) & USB_CMD_DNLTM_BELT_MASK) 411 412 /* USB_ITPN - bitmasks */ 413 /* 414 * ITP(SS) / SOF (HS/FS) number 415 * In SS mode this field represent number of last ITP received from host. 416 * In HS/FS mode this field represent number of last SOF received from host. 417 */ 418 #define USB_ITPN_MASK GENMASK(13, 0) 419 #define USB_ITPN(p) ((p) & USB_ITPN_MASK) 420 421 /* USB_LPM - bitmasks */ 422 /* Host Initiated Resume Duration. */ 423 #define USB_LPM_HIRD_MASK GENMASK(3, 0) 424 #define USB_LPM_HIRD(p) ((p) & USB_LPM_HIRD_MASK) 425 /* Remote Wakeup Enable (bRemoteWake). */ 426 #define USB_LPM_BRW BIT(4) 427 428 /* USB_IEN - bitmasks */ 429 /* SS connection interrupt enable */ 430 #define USB_IEN_CONIEN BIT(0) 431 /* SS disconnection interrupt enable. */ 432 #define USB_IEN_DISIEN BIT(1) 433 /* USB SS warm reset interrupt enable. */ 434 #define USB_IEN_UWRESIEN BIT(2) 435 /* USB SS hot reset interrupt enable */ 436 #define USB_IEN_UHRESIEN BIT(3) 437 /* SS link U3 state enter interrupt enable (suspend).*/ 438 #define USB_IEN_U3ENTIEN BIT(4) 439 /* SS link U3 state exit interrupt enable (wakeup). */ 440 #define USB_IEN_U3EXTIEN BIT(5) 441 /* SS link U2 state enter interrupt enable.*/ 442 #define USB_IEN_U2ENTIEN BIT(6) 443 /* SS link U2 state exit interrupt enable.*/ 444 #define USB_IEN_U2EXTIEN BIT(7) 445 /* SS link U1 state enter interrupt enable.*/ 446 #define USB_IEN_U1ENTIEN BIT(8) 447 /* SS link U1 state exit interrupt enable.*/ 448 #define USB_IEN_U1EXTIEN BIT(9) 449 /* ITP/SOF packet detected interrupt enable.*/ 450 #define USB_IEN_ITPIEN BIT(10) 451 /* Wakeup interrupt enable.*/ 452 #define USB_IEN_WAKEIEN BIT(11) 453 /* Send Custom Packet interrupt enable.*/ 454 #define USB_IEN_SPKTIEN BIT(12) 455 /* HS/FS mode connection interrupt enable.*/ 456 #define USB_IEN_CON2IEN BIT(16) 457 /* HS/FS mode disconnection interrupt enable.*/ 458 #define USB_IEN_DIS2IEN BIT(17) 459 /* USB reset (HS/FS mode) interrupt enable.*/ 460 #define USB_IEN_U2RESIEN BIT(18) 461 /* LPM L2 state enter interrupt enable.*/ 462 #define USB_IEN_L2ENTIEN BIT(20) 463 /* LPM L2 state exit interrupt enable.*/ 464 #define USB_IEN_L2EXTIEN BIT(21) 465 /* LPM L1 state enter interrupt enable.*/ 466 #define USB_IEN_L1ENTIEN BIT(24) 467 /* LPM L1 state exit interrupt enable.*/ 468 #define USB_IEN_L1EXTIEN BIT(25) 469 /* Configuration reset interrupt enable.*/ 470 #define USB_IEN_CFGRESIEN BIT(26) 471 /* Start of the USB SS warm reset interrupt enable.*/ 472 #define USB_IEN_UWRESSIEN BIT(28) 473 /* End of the USB SS warm reset interrupt enable.*/ 474 #define USB_IEN_UWRESEIEN BIT(29) 475 476 #define USB_IEN_INIT (USB_IEN_U2RESIEN | USB_ISTS_DIS2I | USB_IEN_CON2IEN \ 477 | USB_IEN_UHRESIEN | USB_IEN_UWRESIEN | USB_IEN_DISIEN \ 478 | USB_IEN_CONIEN | USB_IEN_U3EXTIEN | USB_IEN_L2ENTIEN \ 479 | USB_IEN_L2EXTIEN | USB_IEN_L1ENTIEN | USB_IEN_U3ENTIEN) 480 481 /* USB_ISTS - bitmasks */ 482 /* SS Connection detected. */ 483 #define USB_ISTS_CONI BIT(0) 484 /* SS Disconnection detected. */ 485 #define USB_ISTS_DISI BIT(1) 486 /* UUSB warm reset detectede. */ 487 #define USB_ISTS_UWRESI BIT(2) 488 /* USB hot reset detected. */ 489 #define USB_ISTS_UHRESI BIT(3) 490 /* U3 link state enter detected (suspend).*/ 491 #define USB_ISTS_U3ENTI BIT(4) 492 /* U3 link state exit detected (wakeup). */ 493 #define USB_ISTS_U3EXTI BIT(5) 494 /* U2 link state enter detected.*/ 495 #define USB_ISTS_U2ENTI BIT(6) 496 /* U2 link state exit detected.*/ 497 #define USB_ISTS_U2EXTI BIT(7) 498 /* U1 link state enter detected.*/ 499 #define USB_ISTS_U1ENTI BIT(8) 500 /* U1 link state exit detected.*/ 501 #define USB_ISTS_U1EXTI BIT(9) 502 /* ITP/SOF packet detected.*/ 503 #define USB_ISTS_ITPI BIT(10) 504 /* Wakeup detected.*/ 505 #define USB_ISTS_WAKEI BIT(11) 506 /* Send Custom Packet detected.*/ 507 #define USB_ISTS_SPKTI BIT(12) 508 /* HS/FS mode connection detected.*/ 509 #define USB_ISTS_CON2I BIT(16) 510 /* HS/FS mode disconnection detected.*/ 511 #define USB_ISTS_DIS2I BIT(17) 512 /* USB reset (HS/FS mode) detected.*/ 513 #define USB_ISTS_U2RESI BIT(18) 514 /* LPM L2 state enter detected.*/ 515 #define USB_ISTS_L2ENTI BIT(20) 516 /* LPM L2 state exit detected.*/ 517 #define USB_ISTS_L2EXTI BIT(21) 518 /* LPM L1 state enter detected.*/ 519 #define USB_ISTS_L1ENTI BIT(24) 520 /* LPM L1 state exit detected.*/ 521 #define USB_ISTS_L1EXTI BIT(25) 522 /* USB configuration reset detected.*/ 523 #define USB_ISTS_CFGRESI BIT(26) 524 /* Start of the USB warm reset detected.*/ 525 #define USB_ISTS_UWRESSI BIT(28) 526 /* End of the USB warm reset detected.*/ 527 #define USB_ISTS_UWRESEI BIT(29) 528 529 /* USB_SEL - bitmasks */ 530 #define EP_SEL_EPNO_MASK GENMASK(3, 0) 531 /* Endpoint number. */ 532 #define EP_SEL_EPNO(p) ((p) & EP_SEL_EPNO_MASK) 533 /* Endpoint direction bit - 0 - OUT, 1 - IN. */ 534 #define EP_SEL_DIR BIT(7) 535 536 #define select_ep_in(nr) (EP_SEL_EPNO(p) | EP_SEL_DIR) 537 #define select_ep_out (EP_SEL_EPNO(p)) 538 539 /* EP_TRADDR - bitmasks */ 540 /* Transfer Ring address. */ 541 #define EP_TRADDR_TRADDR(p) ((p)) 542 543 /* EP_CFG - bitmasks */ 544 /* Endpoint enable */ 545 #define EP_CFG_ENABLE BIT(0) 546 /* 547 * Endpoint type. 548 * 1 - isochronous 549 * 2 - bulk 550 * 3 - interrupt 551 */ 552 #define EP_CFG_EPTYPE_MASK GENMASK(2, 1) 553 #define EP_CFG_EPTYPE(p) (((p) << 1) & EP_CFG_EPTYPE_MASK) 554 /* Stream support enable (only in SS mode). */ 555 #define EP_CFG_STREAM_EN BIT(3) 556 /* TDL check (only in SS mode for BULK EP). */ 557 #define EP_CFG_TDL_CHK BIT(4) 558 /* SID check (only in SS mode for BULK OUT EP). */ 559 #define EP_CFG_SID_CHK BIT(5) 560 /* DMA transfer endianness. */ 561 #define EP_CFG_EPENDIAN BIT(7) 562 /* Max burst size (used only in SS mode). */ 563 #define EP_CFG_MAXBURST_MASK GENMASK(11, 8) 564 #define EP_CFG_MAXBURST(p) (((p) << 8) & EP_CFG_MAXBURST_MASK) 565 #define EP_CFG_MAXBURST_MAX 15 566 /* ISO max burst. */ 567 #define EP_CFG_MULT_MASK GENMASK(15, 14) 568 #define EP_CFG_MULT(p) (((p) << 14) & EP_CFG_MULT_MASK) 569 #define EP_CFG_MULT_MAX 2 570 /* ISO max burst. */ 571 #define EP_CFG_MAXPKTSIZE_MASK GENMASK(26, 16) 572 #define EP_CFG_MAXPKTSIZE(p) (((p) << 16) & EP_CFG_MAXPKTSIZE_MASK) 573 /* Max number of buffered packets. */ 574 #define EP_CFG_BUFFERING_MASK GENMASK(31, 27) 575 #define EP_CFG_BUFFERING(p) (((p) << 27) & EP_CFG_BUFFERING_MASK) 576 #define EP_CFG_BUFFERING_MAX 15 577 578 /* EP_CMD - bitmasks */ 579 /* Endpoint reset. */ 580 #define EP_CMD_EPRST BIT(0) 581 /* Endpoint STALL set. */ 582 #define EP_CMD_SSTALL BIT(1) 583 /* Endpoint STALL clear. */ 584 #define EP_CMD_CSTALL BIT(2) 585 /* Send ERDY TP. */ 586 #define EP_CMD_ERDY BIT(3) 587 /* Request complete. */ 588 #define EP_CMD_REQ_CMPL BIT(5) 589 /* Transfer descriptor ready. */ 590 #define EP_CMD_DRDY BIT(6) 591 /* Data flush. */ 592 #define EP_CMD_DFLUSH BIT(7) 593 /* 594 * Transfer Descriptor Length write (used only for Bulk Stream capable 595 * endpoints in SS mode). 596 * Bit Removed from DEV_VER_V3 controller version. 597 */ 598 #define EP_CMD_STDL BIT(8) 599 /* 600 * Transfer Descriptor Length (used only in SS mode for bulk endpoints). 601 * Bits Removed from DEV_VER_V3 controller version. 602 */ 603 #define EP_CMD_TDL_MASK GENMASK(15, 9) 604 #define EP_CMD_TDL_SET(p) (((p) << 9) & EP_CMD_TDL_MASK) 605 #define EP_CMD_TDL_GET(p) (((p) & EP_CMD_TDL_MASK) >> 9) 606 #define EP_CMD_TDL_MAX (EP_CMD_TDL_MASK >> 9) 607 608 /* ERDY Stream ID value (used in SS mode). */ 609 #define EP_CMD_ERDY_SID_MASK GENMASK(31, 16) 610 #define EP_CMD_ERDY_SID(p) (((p) << 16) & EP_CMD_ERDY_SID_MASK) 611 612 /* EP_STS - bitmasks */ 613 /* Setup transfer complete. */ 614 #define EP_STS_SETUP BIT(0) 615 /* Endpoint STALL status. */ 616 #define EP_STS_STALL(p) ((p) & BIT(1)) 617 /* Interrupt On Complete. */ 618 #define EP_STS_IOC BIT(2) 619 /* Interrupt on Short Packet. */ 620 #define EP_STS_ISP BIT(3) 621 /* Transfer descriptor missing. */ 622 #define EP_STS_DESCMIS BIT(4) 623 /* Stream Rejected (used only in SS mode) */ 624 #define EP_STS_STREAMR BIT(5) 625 /* EXIT from MOVE DATA State (used only for stream transfers in SS mode). */ 626 #define EP_STS_MD_EXIT BIT(6) 627 /* TRB error. */ 628 #define EP_STS_TRBERR BIT(7) 629 /* Not ready (used only in SS mode). */ 630 #define EP_STS_NRDY BIT(8) 631 /* DMA busy bit. */ 632 #define EP_STS_DBUSY BIT(9) 633 /* Endpoint Buffer Empty */ 634 #define EP_STS_BUFFEMPTY(p) ((p) & BIT(10)) 635 /* Current Cycle Status */ 636 #define EP_STS_CCS(p) ((p) & BIT(11)) 637 /* Prime (used only in SS mode. */ 638 #define EP_STS_PRIME BIT(12) 639 /* Stream error (used only in SS mode). */ 640 #define EP_STS_SIDERR BIT(13) 641 /* OUT size mismatch. */ 642 #define EP_STS_OUTSMM BIT(14) 643 /* ISO transmission error. */ 644 #define EP_STS_ISOERR BIT(15) 645 /* Host Packet Pending (only for SS mode). */ 646 #define EP_STS_HOSTPP(p) ((p) & BIT(16)) 647 /* Stream Protocol State Machine State (only for Bulk stream endpoints). */ 648 #define EP_STS_SPSMST_MASK GENMASK(18, 17) 649 #define EP_STS_SPSMST_DISABLED(p) (((p) & EP_STS_SPSMST_MASK) >> 17) 650 #define EP_STS_SPSMST_IDLE(p) (((p) & EP_STS_SPSMST_MASK) >> 17) 651 #define EP_STS_SPSMST_START_STREAM(p) (((p) & EP_STS_SPSMST_MASK) >> 17) 652 #define EP_STS_SPSMST_MOVE_DATA(p) (((p) & EP_STS_SPSMST_MASK) >> 17) 653 /* Interrupt On Transfer complete. */ 654 #define EP_STS_IOT BIT(19) 655 /* OUT queue endpoint number. */ 656 #define EP_STS_OUTQ_NO_MASK GENMASK(27, 24) 657 #define EP_STS_OUTQ_NO(p) (((p) & EP_STS_OUTQ_NO_MASK) >> 24) 658 /* OUT queue valid flag. */ 659 #define EP_STS_OUTQ_VAL_MASK BIT(28) 660 #define EP_STS_OUTQ_VAL(p) ((p) & EP_STS_OUTQ_VAL_MASK) 661 /* SETUP WAIT. */ 662 #define EP_STS_STPWAIT BIT(31) 663 664 /* EP_STS_SID - bitmasks */ 665 /* Stream ID (used only in SS mode). */ 666 #define EP_STS_SID_MASK GENMASK(15, 0) 667 #define EP_STS_SID(p) ((p) & EP_STS_SID_MASK) 668 669 /* EP_STS_EN - bitmasks */ 670 /* SETUP interrupt enable. */ 671 #define EP_STS_EN_SETUPEN BIT(0) 672 /* OUT transfer missing descriptor enable. */ 673 #define EP_STS_EN_DESCMISEN BIT(4) 674 /* Stream Rejected enable. */ 675 #define EP_STS_EN_STREAMREN BIT(5) 676 /* Move Data Exit enable.*/ 677 #define EP_STS_EN_MD_EXITEN BIT(6) 678 /* TRB enable. */ 679 #define EP_STS_EN_TRBERREN BIT(7) 680 /* NRDY enable. */ 681 #define EP_STS_EN_NRDYEN BIT(8) 682 /* Prime enable. */ 683 #define EP_STS_EN_PRIMEEEN BIT(12) 684 /* Stream error enable. */ 685 #define EP_STS_EN_SIDERREN BIT(13) 686 /* OUT size mismatch enable. */ 687 #define EP_STS_EN_OUTSMMEN BIT(14) 688 /* ISO transmission error enable. */ 689 #define EP_STS_EN_ISOERREN BIT(15) 690 /* Interrupt on Transmission complete enable. */ 691 #define EP_STS_EN_IOTEN BIT(19) 692 /* Setup Wait interrupt enable. */ 693 #define EP_STS_EN_STPWAITEN BIT(31) 694 695 /* DRBL- bitmasks */ 696 #define DB_VALUE_BY_INDEX(index) (1 << (index)) 697 #define DB_VALUE_EP0_OUT BIT(0) 698 #define DB_VALUE_EP0_IN BIT(16) 699 700 /* EP_IEN - bitmasks */ 701 #define EP_IEN(index) (1 << (index)) 702 #define EP_IEN_EP_OUT0 BIT(0) 703 #define EP_IEN_EP_IN0 BIT(16) 704 705 /* EP_ISTS - bitmasks */ 706 #define EP_ISTS(index) (1 << (index)) 707 #define EP_ISTS_EP_OUT0 BIT(0) 708 #define EP_ISTS_EP_IN0 BIT(16) 709 710 /* USB_PWR- bitmasks */ 711 /*Power Shut Off capability enable*/ 712 #define PUSB_PWR_PSO_EN BIT(0) 713 /*Power Shut Off capability disable*/ 714 #define PUSB_PWR_PSO_DS BIT(1) 715 /* 716 * Enables turning-off Reference Clock. 717 * This bit is optional and implemented only when support for OTG is 718 * implemented (indicated by OTG_READY bit set to '1'). 719 */ 720 #define PUSB_PWR_STB_CLK_SWITCH_EN BIT(8) 721 /* 722 * Status bit indicating that operation required by STB_CLK_SWITCH_EN write 723 * is completed 724 */ 725 #define PUSB_PWR_STB_CLK_SWITCH_DONE BIT(9) 726 /* This bit informs if Fast Registers Access is enabled. */ 727 #define PUSB_PWR_FST_REG_ACCESS_STAT BIT(30) 728 /* Fast Registers Access Enable. */ 729 #define PUSB_PWR_FST_REG_ACCESS BIT(31) 730 731 /* USB_CONF2- bitmasks */ 732 /* 733 * Writing 1 disables TDL calculation basing on TRB feature in controller 734 * for DMULT mode. 735 * Bit supported only for DEV_VER_V2 version. 736 */ 737 #define USB_CONF2_DIS_TDL_TRB BIT(1) 738 /* 739 * Writing 1 enables TDL calculation basing on TRB feature in controller 740 * for DMULT mode. 741 * Bit supported only for DEV_VER_V2 version. 742 */ 743 #define USB_CONF2_EN_TDL_TRB BIT(2) 744 745 /* USB_CAP1- bitmasks */ 746 /* 747 * SFR Interface type 748 * These field reflects type of SFR interface implemented: 749 * 0x0 - OCP 750 * 0x1 - AHB, 751 * 0x2 - PLB 752 * 0x3 - AXI 753 * 0x4-0xF - reserved 754 */ 755 #define USB_CAP1_SFR_TYPE_MASK GENMASK(3, 0) 756 #define DEV_SFR_TYPE_OCP(p) (((p) & USB_CAP1_SFR_TYPE_MASK) == 0x0) 757 #define DEV_SFR_TYPE_AHB(p) (((p) & USB_CAP1_SFR_TYPE_MASK) == 0x1) 758 #define DEV_SFR_TYPE_PLB(p) (((p) & USB_CAP1_SFR_TYPE_MASK) == 0x2) 759 #define DEV_SFR_TYPE_AXI(p) (((p) & USB_CAP1_SFR_TYPE_MASK) == 0x3) 760 /* 761 * SFR Interface width 762 * These field reflects width of SFR interface implemented: 763 * 0x0 - 8 bit interface, 764 * 0x1 - 16 bit interface, 765 * 0x2 - 32 bit interface 766 * 0x3 - 64 bit interface 767 * 0x4-0xF - reserved 768 */ 769 #define USB_CAP1_SFR_WIDTH_MASK GENMASK(7, 4) 770 #define DEV_SFR_WIDTH_8(p) (((p) & USB_CAP1_SFR_WIDTH_MASK) == (0x0 << 4)) 771 #define DEV_SFR_WIDTH_16(p) (((p) & USB_CAP1_SFR_WIDTH_MASK) == (0x1 << 4)) 772 #define DEV_SFR_WIDTH_32(p) (((p) & USB_CAP1_SFR_WIDTH_MASK) == (0x2 << 4)) 773 #define DEV_SFR_WIDTH_64(p) (((p) & USB_CAP1_SFR_WIDTH_MASK) == (0x3 << 4)) 774 /* 775 * DMA Interface type 776 * These field reflects type of DMA interface implemented: 777 * 0x0 - OCP 778 * 0x1 - AHB, 779 * 0x2 - PLB 780 * 0x3 - AXI 781 * 0x4-0xF - reserved 782 */ 783 #define USB_CAP1_DMA_TYPE_MASK GENMASK(11, 8) 784 #define DEV_DMA_TYPE_OCP(p) (((p) & USB_CAP1_DMA_TYPE_MASK) == (0x0 << 8)) 785 #define DEV_DMA_TYPE_AHB(p) (((p) & USB_CAP1_DMA_TYPE_MASK) == (0x1 << 8)) 786 #define DEV_DMA_TYPE_PLB(p) (((p) & USB_CAP1_DMA_TYPE_MASK) == (0x2 << 8)) 787 #define DEV_DMA_TYPE_AXI(p) (((p) & USB_CAP1_DMA_TYPE_MASK) == (0x3 << 8)) 788 /* 789 * DMA Interface width 790 * These field reflects width of DMA interface implemented: 791 * 0x0 - reserved, 792 * 0x1 - reserved, 793 * 0x2 - 32 bit interface 794 * 0x3 - 64 bit interface 795 * 0x4-0xF - reserved 796 */ 797 #define USB_CAP1_DMA_WIDTH_MASK GENMASK(15, 12) 798 #define DEV_DMA_WIDTH_32(p) (((p) & USB_CAP1_DMA_WIDTH_MASK) == (0x2 << 12)) 799 #define DEV_DMA_WIDTH_64(p) (((p) & USB_CAP1_DMA_WIDTH_MASK) == (0x3 << 12)) 800 /* 801 * USB3 PHY Interface type 802 * These field reflects type of USB3 PHY interface implemented: 803 * 0x0 - USB PIPE, 804 * 0x1 - RMMI, 805 * 0x2-0xF - reserved 806 */ 807 #define USB_CAP1_U3PHY_TYPE_MASK GENMASK(19, 16) 808 #define DEV_U3PHY_PIPE(p) (((p) & USB_CAP1_U3PHY_TYPE_MASK) == (0x0 << 16)) 809 #define DEV_U3PHY_RMMI(p) (((p) & USB_CAP1_U3PHY_TYPE_MASK) == (0x1 << 16)) 810 /* 811 * USB3 PHY Interface width 812 * These field reflects width of USB3 PHY interface implemented: 813 * 0x0 - 8 bit PIPE interface, 814 * 0x1 - 16 bit PIPE interface, 815 * 0x2 - 32 bit PIPE interface, 816 * 0x3 - 64 bit PIPE interface 817 * 0x4-0xF - reserved 818 * Note: When SSIC interface is implemented this field shows the width of 819 * internal PIPE interface. The RMMI interface is always 20bit wide. 820 */ 821 #define USB_CAP1_U3PHY_WIDTH_MASK GENMASK(23, 20) 822 #define DEV_U3PHY_WIDTH_8(p) \ 823 (((p) & USB_CAP1_U3PHY_WIDTH_MASK) == (0x0 << 20)) 824 #define DEV_U3PHY_WIDTH_16(p) \ 825 (((p) & USB_CAP1_U3PHY_WIDTH_MASK) == (0x1 << 16)) 826 #define DEV_U3PHY_WIDTH_32(p) \ 827 (((p) & USB_CAP1_U3PHY_WIDTH_MASK) == (0x2 << 20)) 828 #define DEV_U3PHY_WIDTH_64(p) \ 829 (((p) & USB_CAP1_U3PHY_WIDTH_MASK) == (0x3 << 16)) 830 831 /* 832 * USB2 PHY Interface enable 833 * These field informs if USB2 PHY interface is implemented: 834 * 0x0 - interface NOT implemented, 835 * 0x1 - interface implemented 836 */ 837 #define USB_CAP1_U2PHY_EN(p) ((p) & BIT(24)) 838 /* 839 * USB2 PHY Interface type 840 * These field reflects type of USB2 PHY interface implemented: 841 * 0x0 - UTMI, 842 * 0x1 - ULPI 843 */ 844 #define DEV_U2PHY_ULPI(p) ((p) & BIT(25)) 845 /* 846 * USB2 PHY Interface width 847 * These field reflects width of USB2 PHY interface implemented: 848 * 0x0 - 8 bit interface, 849 * 0x1 - 16 bit interface, 850 * Note: The ULPI interface is always 8bit wide. 851 */ 852 #define DEV_U2PHY_WIDTH_16(p) ((p) & BIT(26)) 853 /* 854 * OTG Ready 855 * 0x0 - pure device mode 856 * 0x1 - some features and ports for CDNS USB OTG controller are implemented. 857 */ 858 #define USB_CAP1_OTG_READY(p) ((p) & BIT(27)) 859 860 /* 861 * When set, indicates that controller supports automatic internal TDL 862 * calculation basing on the size provided in TRB (TRB[22:17]) for DMULT mode 863 * Supported only for DEV_VER_V2 controller version. 864 */ 865 #define USB_CAP1_TDL_FROM_TRB(p) ((p) & BIT(28)) 866 867 /* USB_CAP2- bitmasks */ 868 /* 869 * The actual size of the connected On-chip RAM memory in kB: 870 * - 0 means 256 kB (max supported mem size) 871 * - value other than 0 reflects the mem size in kB 872 */ 873 #define USB_CAP2_ACTUAL_MEM_SIZE(p) ((p) & GENMASK(7, 0)) 874 /* 875 * Max supported mem size 876 * These field reflects width of on-chip RAM address bus width, 877 * which determines max supported mem size: 878 * 0x0-0x7 - reserved, 879 * 0x8 - support for 4kB mem, 880 * 0x9 - support for 8kB mem, 881 * 0xA - support for 16kB mem, 882 * 0xB - support for 32kB mem, 883 * 0xC - support for 64kB mem, 884 * 0xD - support for 128kB mem, 885 * 0xE - support for 256kB mem, 886 * 0xF - reserved 887 */ 888 #define USB_CAP2_MAX_MEM_SIZE(p) ((p) & GENMASK(11, 8)) 889 890 /* USB_CAP3- bitmasks */ 891 #define EP_IS_IMPLEMENTED(reg, index) ((reg) & (1 << (index))) 892 893 /* USB_CAP4- bitmasks */ 894 #define EP_SUPPORT_ISO(reg, index) ((reg) & (1 << (index))) 895 896 /* USB_CAP5- bitmasks */ 897 #define EP_SUPPORT_STREAM(reg, index) ((reg) & (1 << (index))) 898 899 /* USB_CAP6- bitmasks */ 900 /* The USBSS-DEV Controller Internal build number. */ 901 #define GET_DEV_BASE_VERSION(p) ((p) & GENMASK(23, 0)) 902 /* The USBSS-DEV Controller version number. */ 903 #define GET_DEV_CUSTOM_VERSION(p) ((p) & GENMASK(31, 24)) 904 905 #define DEV_VER_NXP_V1 0x00024502 906 #define DEV_VER_TI_V1 0x00024509 907 #define DEV_VER_V2 0x0002450C 908 #define DEV_VER_V3 0x0002450d 909 910 /* DBG_LINK1- bitmasks */ 911 /* 912 * LFPS_MIN_DET_U1_EXIT value This parameter configures the minimum 913 * time required for decoding the received LFPS as an LFPS.U1_Exit. 914 */ 915 #define DBG_LINK1_LFPS_MIN_DET_U1_EXIT(p) ((p) & GENMASK(7, 0)) 916 /* 917 * LFPS_MIN_GEN_U1_EXIT value This parameter configures the minimum time for 918 * phytxelecidle deassertion when LFPS.U1_Exit 919 */ 920 #define DBG_LINK1_LFPS_MIN_GEN_U1_EXIT_MASK GENMASK(15, 8) 921 #define DBG_LINK1_LFPS_MIN_GEN_U1_EXIT(p) (((p) << 8) & GENMASK(15, 8)) 922 /* 923 * RXDET_BREAK_DIS value This parameter configures terminating the Far-end 924 * Receiver termination detection sequence: 925 * 0: it is possible that USBSS_DEV will terminate Farend receiver 926 * termination detection sequence 927 * 1: USBSS_DEV will not terminate Far-end receiver termination 928 * detection sequence 929 */ 930 #define DBG_LINK1_RXDET_BREAK_DIS BIT(16) 931 /* LFPS_GEN_PING value This parameter configures the LFPS.Ping generation */ 932 #define DBG_LINK1_LFPS_GEN_PING(p) (((p) << 17) & GENMASK(21, 17)) 933 /* 934 * Set the LFPS_MIN_DET_U1_EXIT value Writing '1' to this bit writes the 935 * LFPS_MIN_DET_U1_EXIT field value to the device. This bit is automatically 936 * cleared. Writing '0' has no effect 937 */ 938 #define DBG_LINK1_LFPS_MIN_DET_U1_EXIT_SET BIT(24) 939 /* 940 * Set the LFPS_MIN_GEN_U1_EXIT value. Writing '1' to this bit writes the 941 * LFPS_MIN_GEN_U1_EXIT field value to the device. This bit is automatically 942 * cleared. Writing '0' has no effect 943 */ 944 #define DBG_LINK1_LFPS_MIN_GEN_U1_EXIT_SET BIT(25) 945 /* 946 * Set the RXDET_BREAK_DIS value Writing '1' to this bit writes 947 * the RXDET_BREAK_DIS field value to the device. This bit is automatically 948 * cleared. Writing '0' has no effect 949 */ 950 #define DBG_LINK1_RXDET_BREAK_DIS_SET BIT(26) 951 /* 952 * Set the LFPS_GEN_PING_SET value Writing '1' to this bit writes 953 * the LFPS_GEN_PING field value to the device. This bit is automatically 954 * cleared. Writing '0' has no effect." 955 */ 956 #define DBG_LINK1_LFPS_GEN_PING_SET BIT(27) 957 958 /* DMA_AXI_CTRL- bitmasks */ 959 /* The mawprot pin configuration. */ 960 #define DMA_AXI_CTRL_MARPROT(p) ((p) & GENMASK(2, 0)) 961 /* The marprot pin configuration. */ 962 #define DMA_AXI_CTRL_MAWPROT(p) (((p) & GENMASK(2, 0)) << 16) 963 #define DMA_AXI_CTRL_NON_SECURE 0x02 964 965 #define gadget_to_cdns3_device(g) (container_of(g, struct cdns3_device, gadget)) 966 967 #define ep_to_cdns3_ep(ep) (container_of(ep, struct cdns3_endpoint, endpoint)) 968 969 /*-------------------------------------------------------------------------*/ 970 /* 971 * USBSS-DEV DMA interface. 972 */ 973 #define TRBS_PER_SEGMENT 600 974 975 #define ISO_MAX_INTERVAL 10 976 977 #define MAX_TRB_LENGTH BIT(16) 978 979 #if TRBS_PER_SEGMENT < 2 980 #error "Incorrect TRBS_PER_SEGMENT. Minimal Transfer Ring size is 2." 981 #endif 982 983 #define TRBS_PER_STREAM_SEGMENT 2 984 985 #if TRBS_PER_STREAM_SEGMENT < 2 986 #error "Incorrect TRBS_PER_STREAMS_SEGMENT. Minimal Transfer Ring size is 2." 987 #endif 988 989 /* 990 *Only for ISOC endpoints - maximum number of TRBs is calculated as 991 * pow(2, bInterval-1) * number of usb requests. It is limitation made by 992 * driver to save memory. Controller must prepare TRB for each ITP even 993 * if bInterval > 1. It's the reason why driver needs so many TRBs for 994 * isochronous endpoints. 995 */ 996 #define TRBS_PER_ISOC_SEGMENT (ISO_MAX_INTERVAL * 8) 997 998 #define GET_TRBS_PER_SEGMENT(ep_type) ((ep_type) == USB_ENDPOINT_XFER_ISOC ? \ 999 TRBS_PER_ISOC_SEGMENT : TRBS_PER_SEGMENT) 1000 /** 1001 * struct cdns3_trb - represent Transfer Descriptor block. 1002 * @buffer: pointer to buffer data 1003 * @length: length of data 1004 * @control: control flags. 1005 * 1006 * This structure describes transfer block serviced by DMA module. 1007 */ 1008 struct cdns3_trb { 1009 __le32 buffer; 1010 __le32 length; 1011 __le32 control; 1012 }; 1013 1014 #define TRB_SIZE (sizeof(struct cdns3_trb)) 1015 #define TRB_RING_SIZE (TRB_SIZE * TRBS_PER_SEGMENT) 1016 #define TRB_STREAM_RING_SIZE (TRB_SIZE * TRBS_PER_STREAM_SEGMENT) 1017 #define TRB_ISO_RING_SIZE (TRB_SIZE * TRBS_PER_ISOC_SEGMENT) 1018 #define TRB_CTRL_RING_SIZE (TRB_SIZE * 2) 1019 1020 /* TRB bit mask */ 1021 #define TRB_TYPE_BITMASK GENMASK(15, 10) 1022 #define TRB_TYPE(p) ((p) << 10) 1023 #define TRB_FIELD_TO_TYPE(p) (((p) & TRB_TYPE_BITMASK) >> 10) 1024 1025 /* TRB type IDs */ 1026 /* bulk, interrupt, isoc , and control data stage */ 1027 #define TRB_NORMAL 1 1028 /* TRB for linking ring segments */ 1029 #define TRB_LINK 6 1030 1031 /* Cycle bit - indicates TRB ownership by driver or hw*/ 1032 #define TRB_CYCLE BIT(0) 1033 /* 1034 * When set to '1', the device will toggle its interpretation of the Cycle bit 1035 */ 1036 #define TRB_TOGGLE BIT(1) 1037 /* 1038 * The controller will set it if OUTSMM (OUT size mismatch) is detected, 1039 * this bit is for normal TRB 1040 */ 1041 #define TRB_SMM BIT(1) 1042 1043 /* 1044 * Short Packet (SP). OUT EPs at DMULT=1 only. Indicates if the TRB was 1045 * processed while USB short packet was received. No more buffers defined by 1046 * the TD will be used. DMA will automatically advance to next TD. 1047 * - Shall be set to 0 by Software when putting TRB on the Transfer Ring 1048 * - Shall be set to 1 by Controller when Short Packet condition for this TRB 1049 * is detected independent if ISP is set or not. 1050 */ 1051 #define TRB_SP BIT(1) 1052 1053 /* Interrupt on short packet*/ 1054 #define TRB_ISP BIT(2) 1055 /*Setting this bit enables FIFO DMA operation mode*/ 1056 #define TRB_FIFO_MODE BIT(3) 1057 /* Set PCIe no snoop attribute */ 1058 #define TRB_CHAIN BIT(4) 1059 /* Interrupt on completion */ 1060 #define TRB_IOC BIT(5) 1061 1062 /* stream ID bitmasks. */ 1063 #define TRB_STREAM_ID_BITMASK GENMASK(31, 16) 1064 #define TRB_STREAM_ID(p) ((p) << 16) 1065 #define TRB_FIELD_TO_STREAMID(p) (((p) & TRB_STREAM_ID_BITMASK) >> 16) 1066 1067 /* Size of TD expressed in USB packets for HS/FS mode. */ 1068 #define TRB_TDL_HS_SIZE(p) (((p) << 16) & GENMASK(31, 16)) 1069 #define TRB_TDL_HS_SIZE_GET(p) (((p) & GENMASK(31, 16)) >> 16) 1070 1071 /* transfer_len bitmasks. */ 1072 #define TRB_LEN(p) ((p) & GENMASK(16, 0)) 1073 1074 /* Size of TD expressed in USB packets for SS mode. */ 1075 #define TRB_TDL_SS_SIZE(p) (((p) << 17) & GENMASK(23, 17)) 1076 #define TRB_TDL_SS_SIZE_GET(p) (((p) & GENMASK(23, 17)) >> 17) 1077 1078 /* transfer_len bitmasks - bits 31:24 */ 1079 #define TRB_BURST_LEN(p) ((unsigned int)((p) << 24) & GENMASK(31, 24)) 1080 #define TRB_BURST_LEN_GET(p) (((p) & GENMASK(31, 24)) >> 24) 1081 1082 /* Data buffer pointer bitmasks*/ 1083 #define TRB_BUFFER(p) ((p) & GENMASK(31, 0)) 1084 1085 /*-------------------------------------------------------------------------*/ 1086 /* Driver numeric constants */ 1087 1088 /* Such declaration should be added to ch9.h */ 1089 #define USB_DEVICE_MAX_ADDRESS 127 1090 1091 /* Endpoint init values */ 1092 #define CDNS3_EP_MAX_PACKET_LIMIT 1024 1093 #define CDNS3_EP_MAX_STREAMS 15 1094 #define CDNS3_EP0_MAX_PACKET_LIMIT 512 1095 1096 /* All endpoints including EP0 */ 1097 #define CDNS3_ENDPOINTS_MAX_COUNT 32 1098 #define CDNS3_EP_ZLP_BUF_SIZE 1024 1099 1100 #define CDNS3_MAX_NUM_DESCMISS_BUF 32 1101 #define CDNS3_DESCMIS_BUF_SIZE 2048 /* Bytes */ 1102 #define CDNS3_WA2_NUM_BUFFERS 128 1103 /*-------------------------------------------------------------------------*/ 1104 /* Used structs */ 1105 1106 struct cdns3_device; 1107 1108 /** 1109 * struct cdns3_endpoint - extended device side representation of USB endpoint. 1110 * @endpoint: usb endpoint 1111 * @pending_req_list: list of requests queuing on transfer ring. 1112 * @deferred_req_list: list of requests waiting for queuing on transfer ring. 1113 * @wa2_descmiss_req_list: list of requests internally allocated by driver. 1114 * @trb_pool: transfer ring - array of transaction buffers 1115 * @trb_pool_dma: dma address of transfer ring 1116 * @cdns3_dev: device associated with this endpoint 1117 * @name: a human readable name e.g. ep1out 1118 * @flags: specify the current state of endpoint 1119 * @descmis_req: internal transfer object used for getting data from on-chip 1120 * buffer. It can happen only if function driver doesn't send usb_request 1121 * object on time. 1122 * @dir: endpoint direction 1123 * @num: endpoint number (1 - 15) 1124 * @type: set to bmAttributes & USB_ENDPOINT_XFERTYPE_MASK 1125 * @interval: interval between packets used for ISOC endpoint. 1126 * @free_trbs: number of free TRBs in transfer ring 1127 * @num_trbs: number of all TRBs in transfer ring 1128 * @alloc_ring_size: size of the allocated TRB ring 1129 * @pcs: producer cycle state 1130 * @ccs: consumer cycle state 1131 * @enqueue: enqueue index in transfer ring 1132 * @dequeue: dequeue index in transfer ring 1133 * @trb_burst_size: number of burst used in trb. 1134 */ 1135 struct cdns3_endpoint { 1136 struct usb_ep endpoint; 1137 struct list_head pending_req_list; 1138 struct list_head deferred_req_list; 1139 struct list_head wa2_descmiss_req_list; 1140 int wa2_counter; 1141 1142 struct cdns3_trb *trb_pool; 1143 dma_addr_t trb_pool_dma; 1144 1145 struct cdns3_device *cdns3_dev; 1146 char name[20]; 1147 1148 #define EP_ENABLED BIT(0) 1149 #define EP_STALLED BIT(1) 1150 #define EP_STALL_PENDING BIT(2) 1151 #define EP_WEDGE BIT(3) 1152 #define EP_TRANSFER_STARTED BIT(4) 1153 #define EP_UPDATE_EP_TRBADDR BIT(5) 1154 #define EP_PENDING_REQUEST BIT(6) 1155 #define EP_RING_FULL BIT(7) 1156 #define EP_CLAIMED BIT(8) 1157 #define EP_DEFERRED_DRDY BIT(9) 1158 #define EP_QUIRK_ISO_OUT_EN BIT(10) 1159 #define EP_QUIRK_END_TRANSFER BIT(11) 1160 #define EP_QUIRK_EXTRA_BUF_DET BIT(12) 1161 #define EP_QUIRK_EXTRA_BUF_EN BIT(13) 1162 #define EP_TDLCHK_EN BIT(15) 1163 #define EP_CONFIGURED BIT(16) 1164 u32 flags; 1165 1166 struct cdns3_request *descmis_req; 1167 1168 u8 dir; 1169 u8 num; 1170 u8 type; 1171 int interval; 1172 1173 int free_trbs; 1174 int num_trbs; 1175 int alloc_ring_size; 1176 u8 pcs; 1177 u8 ccs; 1178 int enqueue; 1179 int dequeue; 1180 u8 trb_burst_size; 1181 1182 unsigned int wa1_set:1; 1183 struct cdns3_trb *wa1_trb; 1184 unsigned int wa1_trb_index; 1185 unsigned int wa1_cycle_bit:1; 1186 1187 /* Stream related */ 1188 unsigned int use_streams:1; 1189 unsigned int prime_flag:1; 1190 u32 ep_sts_pending; 1191 u16 last_stream_id; 1192 u16 pending_tdl; 1193 unsigned int stream_sg_idx; 1194 }; 1195 1196 /** 1197 * struct cdns3_aligned_buf - represent aligned buffer used for DMA transfer 1198 * @buf: aligned to 8 bytes data buffer. Buffer address used in 1199 * TRB shall be aligned to 8. 1200 * @dma: dma address 1201 * @size: size of buffer 1202 * @in_use: inform if this buffer is associated with usb_request 1203 * @list: used to adding instance of this object to list 1204 */ 1205 struct cdns3_aligned_buf { 1206 void *buf; 1207 dma_addr_t dma; 1208 u32 size; 1209 enum dma_data_direction dir; 1210 unsigned in_use:1; 1211 struct list_head list; 1212 }; 1213 1214 /** 1215 * struct cdns3_request - extended device side representation of usb_request 1216 * object . 1217 * @request: generic usb_request object describing single I/O request. 1218 * @priv_ep: extended representation of usb_ep object 1219 * @trb: the first TRB association with this request 1220 * @start_trb: number of the first TRB in transfer ring 1221 * @end_trb: number of the last TRB in transfer ring 1222 * @aligned_buf: object holds information about aligned buffer associated whit 1223 * this endpoint 1224 * @flags: flag specifying special usage of request 1225 * @list: used by internally allocated request to add to wa2_descmiss_req_list. 1226 * @finished_trb: number of trb has already finished per request 1227 * @num_of_trb: how many trbs in this request 1228 */ 1229 struct cdns3_request { 1230 struct usb_request request; 1231 struct cdns3_endpoint *priv_ep; 1232 struct cdns3_trb *trb; 1233 int start_trb; 1234 int end_trb; 1235 struct cdns3_aligned_buf *aligned_buf; 1236 #define REQUEST_PENDING BIT(0) 1237 #define REQUEST_INTERNAL BIT(1) 1238 #define REQUEST_INTERNAL_CH BIT(2) 1239 #define REQUEST_ZLP BIT(3) 1240 #define REQUEST_UNALIGNED BIT(4) 1241 u32 flags; 1242 struct list_head list; 1243 int finished_trb; 1244 int num_of_trb; 1245 }; 1246 1247 #define to_cdns3_request(r) (container_of(r, struct cdns3_request, request)) 1248 1249 /*Stages used during enumeration process.*/ 1250 #define CDNS3_SETUP_STAGE 0x0 1251 #define CDNS3_DATA_STAGE 0x1 1252 #define CDNS3_STATUS_STAGE 0x2 1253 1254 /** 1255 * struct cdns3_device - represent USB device. 1256 * @dev: pointer to device structure associated whit this controller 1257 * @sysdev: pointer to the DMA capable device 1258 * @gadget: device side representation of the peripheral controller 1259 * @gadget_driver: pointer to the gadget driver 1260 * @dev_ver: device controller version. 1261 * @lock: for synchronizing 1262 * @regs: base address for device side registers 1263 * @setup_buf: used while processing usb control requests 1264 * @setup_dma: dma address for setup_buf 1265 * @zlp_buf - zlp buffer 1266 * @ep0_stage: ep0 stage during enumeration process. 1267 * @ep0_data_dir: direction for control transfer 1268 * @eps: array of pointers to all endpoints with exclusion ep0 1269 * @aligned_buf_list: list of aligned buffers internally allocated by driver 1270 * @aligned_buf_wq: workqueue freeing no longer used aligned buf. 1271 * @selected_ep: actually selected endpoint. It's used only to improve 1272 * performance. 1273 * @isoch_delay: value from Set Isoch Delay request. Only valid on SS/SSP. 1274 * @u1_allowed: allow device transition to u1 state 1275 * @u2_allowed: allow device transition to u2 state 1276 * @is_selfpowered: device is self powered 1277 * @setup_pending: setup packet is processing by gadget driver 1278 * @hw_configured_flag: hardware endpoint configuration was set. 1279 * @wake_up_flag: allow device to remote up the host 1280 * @status_completion_no_call: indicate that driver is waiting for status s 1281 * stage completion. It's used in deferred SET_CONFIGURATION request. 1282 * @onchip_buffers: number of available on-chip buffers. 1283 * @onchip_used_size: actual size of on-chip memory assigned to endpoints. 1284 * @pending_status_wq: workqueue handling status stage for deferred requests. 1285 * @pending_status_request: request for which status stage was deferred 1286 */ 1287 struct cdns3_device { 1288 struct device *dev; 1289 struct device *sysdev; 1290 1291 struct usb_gadget gadget; 1292 struct usb_gadget_driver *gadget_driver; 1293 1294 #define CDNS_REVISION_V0 0x00024501 1295 #define CDNS_REVISION_V1 0x00024509 1296 u32 dev_ver; 1297 1298 /* generic spin-lock for drivers */ 1299 spinlock_t lock; 1300 1301 struct cdns3_usb_regs __iomem *regs; 1302 1303 struct dma_pool *eps_dma_pool; 1304 struct usb_ctrlrequest *setup_buf; 1305 dma_addr_t setup_dma; 1306 void *zlp_buf; 1307 1308 u8 ep0_stage; 1309 int ep0_data_dir; 1310 1311 struct cdns3_endpoint *eps[CDNS3_ENDPOINTS_MAX_COUNT]; 1312 1313 struct list_head aligned_buf_list; 1314 struct work_struct aligned_buf_wq; 1315 1316 u32 selected_ep; 1317 u16 isoch_delay; 1318 1319 unsigned wait_for_setup:1; 1320 unsigned u1_allowed:1; 1321 unsigned u2_allowed:1; 1322 unsigned is_selfpowered:1; 1323 unsigned setup_pending:1; 1324 unsigned hw_configured_flag:1; 1325 unsigned wake_up_flag:1; 1326 unsigned status_completion_no_call:1; 1327 unsigned using_streams:1; 1328 int out_mem_is_allocated; 1329 1330 struct work_struct pending_status_wq; 1331 struct usb_request *pending_status_request; 1332 1333 /*in KB */ 1334 u16 onchip_buffers; 1335 u16 onchip_used_size; 1336 1337 u16 ep_buf_size; 1338 u16 ep_iso_burst; 1339 }; 1340 1341 void cdns3_set_register_bit(void __iomem *ptr, u32 mask); 1342 dma_addr_t cdns3_trb_virt_to_dma(struct cdns3_endpoint *priv_ep, 1343 struct cdns3_trb *trb); 1344 enum usb_device_speed cdns3_get_speed(struct cdns3_device *priv_dev); 1345 void cdns3_pending_setup_status_handler(struct work_struct *work); 1346 void cdns3_hw_reset_eps_config(struct cdns3_device *priv_dev); 1347 void cdns3_set_hw_configuration(struct cdns3_device *priv_dev); 1348 void cdns3_select_ep(struct cdns3_device *priv_dev, u32 ep); 1349 void cdns3_allow_enable_l1(struct cdns3_device *priv_dev, int enable); 1350 struct usb_request *cdns3_next_request(struct list_head *list); 1351 void cdns3_rearm_transfer(struct cdns3_endpoint *priv_ep, u8 rearm); 1352 int cdns3_allocate_trb_pool(struct cdns3_endpoint *priv_ep); 1353 u8 cdns3_ep_addr_to_index(u8 ep_addr); 1354 int cdns3_gadget_ep_set_wedge(struct usb_ep *ep); 1355 int cdns3_gadget_ep_set_halt(struct usb_ep *ep, int value); 1356 void __cdns3_gadget_ep_set_halt(struct cdns3_endpoint *priv_ep); 1357 int __cdns3_gadget_ep_clear_halt(struct cdns3_endpoint *priv_ep); 1358 struct usb_request *cdns3_gadget_ep_alloc_request(struct usb_ep *ep, 1359 gfp_t gfp_flags); 1360 void cdns3_gadget_ep_free_request(struct usb_ep *ep, 1361 struct usb_request *request); 1362 int cdns3_gadget_ep_dequeue(struct usb_ep *ep, struct usb_request *request); 1363 void cdns3_gadget_giveback(struct cdns3_endpoint *priv_ep, 1364 struct cdns3_request *priv_req, 1365 int status); 1366 1367 int cdns3_init_ep0(struct cdns3_device *priv_dev, 1368 struct cdns3_endpoint *priv_ep); 1369 void cdns3_ep0_config(struct cdns3_device *priv_dev); 1370 int cdns3_ep_config(struct cdns3_endpoint *priv_ep, bool enable); 1371 void cdns3_check_ep0_interrupt_proceed(struct cdns3_device *priv_dev, int dir); 1372 int __cdns3_gadget_wakeup(struct cdns3_device *priv_dev); 1373 1374 #endif /* __LINUX_CDNS3_GADGET */ 1375