1# 2# USB device configuration 3# 4 5config USB_OHCI_BIG_ENDIAN_DESC 6 bool 7 8config USB_OHCI_BIG_ENDIAN_MMIO 9 bool 10 11config USB_OHCI_LITTLE_ENDIAN 12 bool 13 default n if STB03xxx || PPC_MPC52xx 14 default y 15 16config USB_EHCI_BIG_ENDIAN_MMIO 17 bool 18 19config USB_EHCI_BIG_ENDIAN_DESC 20 bool 21 22menuconfig USB_SUPPORT 23 bool "USB support" 24 depends on HAS_IOMEM 25 default y 26 ---help--- 27 This option adds core support for Universal Serial Bus (USB). 28 You will also need drivers from the following menu to make use of it. 29 30if USB_SUPPORT 31 32config USB_COMMON 33 tristate 34 35config USB_ARCH_HAS_HCD 36 def_bool y 37 38# ARM SA1111 chips have a non-PCI based "OHCI-compatible" USB host interface. 39config USB 40 tristate "Support for Host-side USB" 41 depends on USB_ARCH_HAS_HCD 42 select USB_COMMON 43 select NLS # for UTF-8 strings 44 ---help--- 45 Universal Serial Bus (USB) is a specification for a serial bus 46 subsystem which offers higher speeds and more features than the 47 traditional PC serial port. The bus supplies power to peripherals 48 and allows for hot swapping. Up to 127 USB peripherals can be 49 connected to a single USB host in a tree structure. 50 51 The USB host is the root of the tree, the peripherals are the 52 leaves and the inner nodes are special USB devices called hubs. 53 Most PCs now have USB host ports, used to connect peripherals 54 such as scanners, keyboards, mice, modems, cameras, disks, 55 flash memory, network links, and printers to the PC. 56 57 Say Y here if your computer has a host-side USB port and you want 58 to use USB devices. You then need to say Y to at least one of the 59 Host Controller Driver (HCD) options below. Choose a USB 1.1 60 controller, such as "UHCI HCD support" or "OHCI HCD support", 61 and "EHCI HCD (USB 2.0) support" except for older systems that 62 do not have USB 2.0 support. It doesn't normally hurt to select 63 them all if you are not certain. 64 65 If your system has a device-side USB port, used in the peripheral 66 side of the USB protocol, see the "USB Gadget" framework instead. 67 68 After choosing your HCD, then select drivers for the USB peripherals 69 you'll be using. You may want to check out the information provided 70 in <file:Documentation/usb/> and especially the links given in 71 <file:Documentation/usb/usb-help.txt>. 72 73 To compile this driver as a module, choose M here: the 74 module will be called usbcore. 75 76if USB 77 78source "drivers/usb/core/Kconfig" 79 80source "drivers/usb/mon/Kconfig" 81 82source "drivers/usb/wusbcore/Kconfig" 83 84source "drivers/usb/host/Kconfig" 85 86source "drivers/usb/renesas_usbhs/Kconfig" 87 88source "drivers/usb/class/Kconfig" 89 90source "drivers/usb/storage/Kconfig" 91 92source "drivers/usb/image/Kconfig" 93 94source "drivers/usb/usbip/Kconfig" 95 96endif 97 98source "drivers/usb/mtu3/Kconfig" 99 100source "drivers/usb/musb/Kconfig" 101 102source "drivers/usb/dwc3/Kconfig" 103 104source "drivers/usb/dwc2/Kconfig" 105 106source "drivers/usb/chipidea/Kconfig" 107 108source "drivers/usb/isp1760/Kconfig" 109 110comment "USB port drivers" 111 112if USB 113 114config USB_USS720 115 tristate "USS720 parport driver" 116 depends on PARPORT 117 select PARPORT_NOT_PC 118 ---help--- 119 This driver is for USB parallel port adapters that use the Lucent 120 Technologies USS-720 chip. These cables are plugged into your USB 121 port and provide USB compatibility to peripherals designed with 122 parallel port interfaces. 123 124 The chip has two modes: automatic mode and manual mode. In automatic 125 mode, it looks to the computer like a standard USB printer. Only 126 printers may be connected to the USS-720 in this mode. The generic 127 USB printer driver ("USB Printer support", above) may be used in 128 that mode, and you can say N here if you want to use the chip only 129 in this mode. 130 131 Manual mode is not limited to printers, any parallel port 132 device should work. This driver utilizes manual mode. 133 Note however that some operations are three orders of magnitude 134 slower than on a PCI/ISA Parallel Port, so timing critical 135 applications might not work. 136 137 Say Y here if you own an USS-720 USB->Parport cable and intend to 138 connect anything other than a printer to it. 139 140 To compile this driver as a module, choose M here: the 141 module will be called uss720. 142 143source "drivers/usb/serial/Kconfig" 144 145source "drivers/usb/misc/Kconfig" 146 147source "drivers/usb/atm/Kconfig" 148 149endif # USB 150 151source "drivers/usb/phy/Kconfig" 152 153source "drivers/usb/gadget/Kconfig" 154 155config USB_LED_TRIG 156 bool "USB LED Triggers" 157 depends on LEDS_CLASS && LEDS_TRIGGERS 158 select USB_COMMON 159 help 160 This option adds LED triggers for USB host and/or gadget activity. 161 162 Say Y here if you are working on a system with led-class supported 163 LEDs and you want to use them as activity indicators for USB host or 164 gadget. 165 166config USB_ULPI_BUS 167 tristate "USB ULPI PHY interface support" 168 select USB_COMMON 169 help 170 UTMI+ Low Pin Interface (ULPI) is specification for a commonly used 171 USB 2.0 PHY interface. The ULPI specification defines a standard set 172 of registers that can be used to detect the vendor and product which 173 allows ULPI to be handled as a bus. This module is the driver for that 174 bus. 175 176 The ULPI interfaces (the buses) are registered by the drivers for USB 177 controllers which support ULPI register access and have ULPI PHY 178 attached to them. The ULPI PHY drivers themselves are normal PHY 179 drivers. 180 181 ULPI PHYs provide often functions such as ADP sensing/probing (OTG 182 protocol) and USB charger detection. 183 184 To compile this driver as a module, choose M here: the module will 185 be called ulpi. 186 187endif # USB_SUPPORT 188