1 // SPDX-License-Identifier: GPL-2.0-only 2 /* 3 * drivers/uio/uio_dmem_genirq.c 4 * 5 * Userspace I/O platform driver with generic IRQ handling code. 6 * 7 * Copyright (C) 2012 Damian Hobson-Garcia 8 * 9 * Based on uio_pdrv_genirq.c by Magnus Damm 10 */ 11 12 #include <linux/platform_device.h> 13 #include <linux/uio_driver.h> 14 #include <linux/spinlock.h> 15 #include <linux/bitops.h> 16 #include <linux/module.h> 17 #include <linux/interrupt.h> 18 #include <linux/platform_data/uio_dmem_genirq.h> 19 #include <linux/stringify.h> 20 #include <linux/pm_runtime.h> 21 #include <linux/dma-mapping.h> 22 #include <linux/slab.h> 23 #include <linux/irq.h> 24 25 #include <linux/of.h> 26 #include <linux/of_platform.h> 27 #include <linux/of_address.h> 28 29 #define DRIVER_NAME "uio_dmem_genirq" 30 #define DMEM_MAP_ERROR (~0) 31 32 struct uio_dmem_genirq_platdata { 33 struct uio_info *uioinfo; 34 spinlock_t lock; 35 unsigned long flags; 36 struct platform_device *pdev; 37 unsigned int dmem_region_start; 38 unsigned int num_dmem_regions; 39 void *dmem_region_vaddr[MAX_UIO_MAPS]; 40 struct mutex alloc_lock; 41 unsigned int refcnt; 42 }; 43 44 static int uio_dmem_genirq_open(struct uio_info *info, struct inode *inode) 45 { 46 struct uio_dmem_genirq_platdata *priv = info->priv; 47 struct uio_mem *uiomem; 48 int dmem_region = priv->dmem_region_start; 49 50 uiomem = &priv->uioinfo->mem[priv->dmem_region_start]; 51 52 mutex_lock(&priv->alloc_lock); 53 while (!priv->refcnt && uiomem < &priv->uioinfo->mem[MAX_UIO_MAPS]) { 54 void *addr; 55 if (!uiomem->size) 56 break; 57 58 addr = dma_alloc_coherent(&priv->pdev->dev, uiomem->size, 59 (dma_addr_t *)&uiomem->addr, GFP_KERNEL); 60 if (!addr) { 61 uiomem->addr = DMEM_MAP_ERROR; 62 } 63 priv->dmem_region_vaddr[dmem_region++] = addr; 64 ++uiomem; 65 } 66 priv->refcnt++; 67 68 mutex_unlock(&priv->alloc_lock); 69 /* Wait until the Runtime PM code has woken up the device */ 70 pm_runtime_get_sync(&priv->pdev->dev); 71 return 0; 72 } 73 74 static int uio_dmem_genirq_release(struct uio_info *info, struct inode *inode) 75 { 76 struct uio_dmem_genirq_platdata *priv = info->priv; 77 struct uio_mem *uiomem; 78 int dmem_region = priv->dmem_region_start; 79 80 /* Tell the Runtime PM code that the device has become idle */ 81 pm_runtime_put_sync(&priv->pdev->dev); 82 83 uiomem = &priv->uioinfo->mem[priv->dmem_region_start]; 84 85 mutex_lock(&priv->alloc_lock); 86 87 priv->refcnt--; 88 while (!priv->refcnt && uiomem < &priv->uioinfo->mem[MAX_UIO_MAPS]) { 89 if (!uiomem->size) 90 break; 91 if (priv->dmem_region_vaddr[dmem_region]) { 92 dma_free_coherent(&priv->pdev->dev, uiomem->size, 93 priv->dmem_region_vaddr[dmem_region], 94 uiomem->addr); 95 } 96 uiomem->addr = DMEM_MAP_ERROR; 97 ++dmem_region; 98 ++uiomem; 99 } 100 101 mutex_unlock(&priv->alloc_lock); 102 return 0; 103 } 104 105 static irqreturn_t uio_dmem_genirq_handler(int irq, struct uio_info *dev_info) 106 { 107 struct uio_dmem_genirq_platdata *priv = dev_info->priv; 108 109 /* Just disable the interrupt in the interrupt controller, and 110 * remember the state so we can allow user space to enable it later. 111 */ 112 113 if (!test_and_set_bit(0, &priv->flags)) 114 disable_irq_nosync(irq); 115 116 return IRQ_HANDLED; 117 } 118 119 static int uio_dmem_genirq_irqcontrol(struct uio_info *dev_info, s32 irq_on) 120 { 121 struct uio_dmem_genirq_platdata *priv = dev_info->priv; 122 unsigned long flags; 123 124 /* Allow user space to enable and disable the interrupt 125 * in the interrupt controller, but keep track of the 126 * state to prevent per-irq depth damage. 127 * 128 * Serialize this operation to support multiple tasks. 129 */ 130 131 spin_lock_irqsave(&priv->lock, flags); 132 if (irq_on) { 133 if (test_and_clear_bit(0, &priv->flags)) 134 enable_irq(dev_info->irq); 135 spin_unlock_irqrestore(&priv->lock, flags); 136 } else { 137 if (!test_and_set_bit(0, &priv->flags)) { 138 spin_unlock_irqrestore(&priv->lock, flags); 139 disable_irq(dev_info->irq); 140 } 141 } 142 143 return 0; 144 } 145 146 static void uio_dmem_genirq_pm_disable(void *data) 147 { 148 struct device *dev = data; 149 150 pm_runtime_disable(dev); 151 } 152 153 static int uio_dmem_genirq_probe(struct platform_device *pdev) 154 { 155 struct uio_dmem_genirq_pdata *pdata = dev_get_platdata(&pdev->dev); 156 struct uio_info *uioinfo = &pdata->uioinfo; 157 struct uio_dmem_genirq_platdata *priv; 158 struct uio_mem *uiomem; 159 int ret = -EINVAL; 160 int i; 161 162 if (pdev->dev.of_node) { 163 /* alloc uioinfo for one device */ 164 uioinfo = devm_kzalloc(&pdev->dev, sizeof(*uioinfo), GFP_KERNEL); 165 if (!uioinfo) { 166 dev_err(&pdev->dev, "unable to kmalloc\n"); 167 return -ENOMEM; 168 } 169 uioinfo->name = devm_kasprintf(&pdev->dev, GFP_KERNEL, "%pOFn", 170 pdev->dev.of_node); 171 uioinfo->version = "devicetree"; 172 } 173 174 if (!uioinfo || !uioinfo->name || !uioinfo->version) { 175 dev_err(&pdev->dev, "missing platform_data\n"); 176 return -EINVAL; 177 } 178 179 if (uioinfo->handler || uioinfo->irqcontrol || 180 uioinfo->irq_flags & IRQF_SHARED) { 181 dev_err(&pdev->dev, "interrupt configuration error\n"); 182 return -EINVAL; 183 } 184 185 priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL); 186 if (!priv) { 187 dev_err(&pdev->dev, "unable to kmalloc\n"); 188 return -ENOMEM; 189 } 190 191 ret = dma_set_coherent_mask(&pdev->dev, DMA_BIT_MASK(32)); 192 if (ret) { 193 dev_err(&pdev->dev, "DMA enable failed\n"); 194 return ret; 195 } 196 197 priv->uioinfo = uioinfo; 198 spin_lock_init(&priv->lock); 199 priv->flags = 0; /* interrupt is enabled to begin with */ 200 priv->pdev = pdev; 201 mutex_init(&priv->alloc_lock); 202 203 if (!uioinfo->irq) { 204 /* Multiple IRQs are not supported */ 205 ret = platform_get_irq(pdev, 0); 206 if (ret == -ENXIO && pdev->dev.of_node) 207 ret = UIO_IRQ_NONE; 208 else if (ret < 0) 209 return ret; 210 uioinfo->irq = ret; 211 } 212 213 if (uioinfo->irq) { 214 struct irq_data *irq_data = irq_get_irq_data(uioinfo->irq); 215 216 /* 217 * If a level interrupt, dont do lazy disable. Otherwise the 218 * irq will fire again since clearing of the actual cause, on 219 * device level, is done in userspace 220 * irqd_is_level_type() isn't used since isn't valid until 221 * irq is configured. 222 */ 223 if (irq_data && 224 irqd_get_trigger_type(irq_data) & IRQ_TYPE_LEVEL_MASK) { 225 dev_dbg(&pdev->dev, "disable lazy unmask\n"); 226 irq_set_status_flags(uioinfo->irq, IRQ_DISABLE_UNLAZY); 227 } 228 } 229 230 uiomem = &uioinfo->mem[0]; 231 232 for (i = 0; i < pdev->num_resources; ++i) { 233 struct resource *r = &pdev->resource[i]; 234 235 if (r->flags != IORESOURCE_MEM) 236 continue; 237 238 if (uiomem >= &uioinfo->mem[MAX_UIO_MAPS]) { 239 dev_warn(&pdev->dev, "device has more than " 240 __stringify(MAX_UIO_MAPS) 241 " I/O memory resources.\n"); 242 break; 243 } 244 245 uiomem->memtype = UIO_MEM_PHYS; 246 uiomem->addr = r->start; 247 uiomem->size = resource_size(r); 248 ++uiomem; 249 } 250 251 priv->dmem_region_start = uiomem - &uioinfo->mem[0]; 252 priv->num_dmem_regions = pdata->num_dynamic_regions; 253 254 for (i = 0; i < pdata->num_dynamic_regions; ++i) { 255 if (uiomem >= &uioinfo->mem[MAX_UIO_MAPS]) { 256 dev_warn(&pdev->dev, "device has more than " 257 __stringify(MAX_UIO_MAPS) 258 " dynamic and fixed memory regions.\n"); 259 break; 260 } 261 uiomem->memtype = UIO_MEM_PHYS; 262 uiomem->addr = DMEM_MAP_ERROR; 263 uiomem->size = pdata->dynamic_region_sizes[i]; 264 ++uiomem; 265 } 266 267 while (uiomem < &uioinfo->mem[MAX_UIO_MAPS]) { 268 uiomem->size = 0; 269 ++uiomem; 270 } 271 272 /* This driver requires no hardware specific kernel code to handle 273 * interrupts. Instead, the interrupt handler simply disables the 274 * interrupt in the interrupt controller. User space is responsible 275 * for performing hardware specific acknowledge and re-enabling of 276 * the interrupt in the interrupt controller. 277 * 278 * Interrupt sharing is not supported. 279 */ 280 281 uioinfo->handler = uio_dmem_genirq_handler; 282 uioinfo->irqcontrol = uio_dmem_genirq_irqcontrol; 283 uioinfo->open = uio_dmem_genirq_open; 284 uioinfo->release = uio_dmem_genirq_release; 285 uioinfo->priv = priv; 286 287 /* Enable Runtime PM for this device: 288 * The device starts in suspended state to allow the hardware to be 289 * turned off by default. The Runtime PM bus code should power on the 290 * hardware and enable clocks at open(). 291 */ 292 pm_runtime_enable(&pdev->dev); 293 294 ret = devm_add_action_or_reset(&pdev->dev, uio_dmem_genirq_pm_disable, &pdev->dev); 295 if (ret) 296 return ret; 297 298 return devm_uio_register_device(&pdev->dev, priv->uioinfo); 299 } 300 301 static int uio_dmem_genirq_runtime_nop(struct device *dev) 302 { 303 /* Runtime PM callback shared between ->runtime_suspend() 304 * and ->runtime_resume(). Simply returns success. 305 * 306 * In this driver pm_runtime_get_sync() and pm_runtime_put_sync() 307 * are used at open() and release() time. This allows the 308 * Runtime PM code to turn off power to the device while the 309 * device is unused, ie before open() and after release(). 310 * 311 * This Runtime PM callback does not need to save or restore 312 * any registers since user space is responsbile for hardware 313 * register reinitialization after open(). 314 */ 315 return 0; 316 } 317 318 static const struct dev_pm_ops uio_dmem_genirq_dev_pm_ops = { 319 .runtime_suspend = uio_dmem_genirq_runtime_nop, 320 .runtime_resume = uio_dmem_genirq_runtime_nop, 321 }; 322 323 #ifdef CONFIG_OF 324 static const struct of_device_id uio_of_genirq_match[] = { 325 { /* empty for now */ }, 326 }; 327 MODULE_DEVICE_TABLE(of, uio_of_genirq_match); 328 #endif 329 330 static struct platform_driver uio_dmem_genirq = { 331 .probe = uio_dmem_genirq_probe, 332 .driver = { 333 .name = DRIVER_NAME, 334 .pm = &uio_dmem_genirq_dev_pm_ops, 335 .of_match_table = of_match_ptr(uio_of_genirq_match), 336 }, 337 }; 338 339 module_platform_driver(uio_dmem_genirq); 340 341 MODULE_AUTHOR("Damian Hobson-Garcia"); 342 MODULE_DESCRIPTION("Userspace I/O platform driver with dynamic memory."); 343 MODULE_LICENSE("GPL v2"); 344 MODULE_ALIAS("platform:" DRIVER_NAME); 345