1 // SPDX-License-Identifier: GPL-1.0+ 2 /* 3 * Device driver for Microgate SyncLink GT serial adapters. 4 * 5 * written by Paul Fulghum for Microgate Corporation 6 * paulkf@microgate.com 7 * 8 * Microgate and SyncLink are trademarks of Microgate Corporation 9 * 10 * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED 11 * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES 12 * OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE 13 * DISCLAIMED. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, 14 * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES 15 * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR 16 * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) 17 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, 18 * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) 19 * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED 20 * OF THE POSSIBILITY OF SUCH DAMAGE. 21 */ 22 23 /* 24 * DEBUG OUTPUT DEFINITIONS 25 * 26 * uncomment lines below to enable specific types of debug output 27 * 28 * DBGINFO information - most verbose output 29 * DBGERR serious errors 30 * DBGBH bottom half service routine debugging 31 * DBGISR interrupt service routine debugging 32 * DBGDATA output receive and transmit data 33 * DBGTBUF output transmit DMA buffers and registers 34 * DBGRBUF output receive DMA buffers and registers 35 */ 36 37 #define DBGINFO(fmt) if (debug_level >= DEBUG_LEVEL_INFO) printk fmt 38 #define DBGERR(fmt) if (debug_level >= DEBUG_LEVEL_ERROR) printk fmt 39 #define DBGBH(fmt) if (debug_level >= DEBUG_LEVEL_BH) printk fmt 40 #define DBGISR(fmt) if (debug_level >= DEBUG_LEVEL_ISR) printk fmt 41 #define DBGDATA(info, buf, size, label) if (debug_level >= DEBUG_LEVEL_DATA) trace_block((info), (buf), (size), (label)) 42 /*#define DBGTBUF(info) dump_tbufs(info)*/ 43 /*#define DBGRBUF(info) dump_rbufs(info)*/ 44 45 46 #include <linux/module.h> 47 #include <linux/errno.h> 48 #include <linux/signal.h> 49 #include <linux/sched.h> 50 #include <linux/timer.h> 51 #include <linux/interrupt.h> 52 #include <linux/pci.h> 53 #include <linux/tty.h> 54 #include <linux/tty_flip.h> 55 #include <linux/serial.h> 56 #include <linux/major.h> 57 #include <linux/string.h> 58 #include <linux/fcntl.h> 59 #include <linux/ptrace.h> 60 #include <linux/ioport.h> 61 #include <linux/mm.h> 62 #include <linux/seq_file.h> 63 #include <linux/slab.h> 64 #include <linux/netdevice.h> 65 #include <linux/vmalloc.h> 66 #include <linux/init.h> 67 #include <linux/delay.h> 68 #include <linux/ioctl.h> 69 #include <linux/termios.h> 70 #include <linux/bitops.h> 71 #include <linux/workqueue.h> 72 #include <linux/hdlc.h> 73 #include <linux/synclink.h> 74 75 #include <asm/io.h> 76 #include <asm/irq.h> 77 #include <asm/dma.h> 78 #include <asm/types.h> 79 #include <linux/uaccess.h> 80 81 #if defined(CONFIG_HDLC) || (defined(CONFIG_HDLC_MODULE) && defined(CONFIG_SYNCLINK_GT_MODULE)) 82 #define SYNCLINK_GENERIC_HDLC 1 83 #else 84 #define SYNCLINK_GENERIC_HDLC 0 85 #endif 86 87 /* 88 * module identification 89 */ 90 static char *driver_name = "SyncLink GT"; 91 static char *slgt_driver_name = "synclink_gt"; 92 static char *tty_dev_prefix = "ttySLG"; 93 MODULE_LICENSE("GPL"); 94 #define MGSL_MAGIC 0x5401 95 #define MAX_DEVICES 32 96 97 static const struct pci_device_id pci_table[] = { 98 {PCI_VENDOR_ID_MICROGATE, SYNCLINK_GT_DEVICE_ID, PCI_ANY_ID, PCI_ANY_ID,}, 99 {PCI_VENDOR_ID_MICROGATE, SYNCLINK_GT2_DEVICE_ID, PCI_ANY_ID, PCI_ANY_ID,}, 100 {PCI_VENDOR_ID_MICROGATE, SYNCLINK_GT4_DEVICE_ID, PCI_ANY_ID, PCI_ANY_ID,}, 101 {PCI_VENDOR_ID_MICROGATE, SYNCLINK_AC_DEVICE_ID, PCI_ANY_ID, PCI_ANY_ID,}, 102 {0,}, /* terminate list */ 103 }; 104 MODULE_DEVICE_TABLE(pci, pci_table); 105 106 static int init_one(struct pci_dev *dev,const struct pci_device_id *ent); 107 static void remove_one(struct pci_dev *dev); 108 static struct pci_driver pci_driver = { 109 .name = "synclink_gt", 110 .id_table = pci_table, 111 .probe = init_one, 112 .remove = remove_one, 113 }; 114 115 static bool pci_registered; 116 117 /* 118 * module configuration and status 119 */ 120 static struct slgt_info *slgt_device_list; 121 static int slgt_device_count; 122 123 static int ttymajor; 124 static int debug_level; 125 static int maxframe[MAX_DEVICES]; 126 127 module_param(ttymajor, int, 0); 128 module_param(debug_level, int, 0); 129 module_param_array(maxframe, int, NULL, 0); 130 131 MODULE_PARM_DESC(ttymajor, "TTY major device number override: 0=auto assigned"); 132 MODULE_PARM_DESC(debug_level, "Debug syslog output: 0=disabled, 1 to 5=increasing detail"); 133 MODULE_PARM_DESC(maxframe, "Maximum frame size used by device (4096 to 65535)"); 134 135 /* 136 * tty support and callbacks 137 */ 138 static struct tty_driver *serial_driver; 139 140 static int open(struct tty_struct *tty, struct file * filp); 141 static void close(struct tty_struct *tty, struct file * filp); 142 static void hangup(struct tty_struct *tty); 143 static void set_termios(struct tty_struct *tty, struct ktermios *old_termios); 144 145 static int write(struct tty_struct *tty, const unsigned char *buf, int count); 146 static int put_char(struct tty_struct *tty, unsigned char ch); 147 static void send_xchar(struct tty_struct *tty, char ch); 148 static void wait_until_sent(struct tty_struct *tty, int timeout); 149 static int write_room(struct tty_struct *tty); 150 static void flush_chars(struct tty_struct *tty); 151 static void flush_buffer(struct tty_struct *tty); 152 static void tx_hold(struct tty_struct *tty); 153 static void tx_release(struct tty_struct *tty); 154 155 static int ioctl(struct tty_struct *tty, unsigned int cmd, unsigned long arg); 156 static int chars_in_buffer(struct tty_struct *tty); 157 static void throttle(struct tty_struct * tty); 158 static void unthrottle(struct tty_struct * tty); 159 static int set_break(struct tty_struct *tty, int break_state); 160 161 /* 162 * generic HDLC support and callbacks 163 */ 164 #if SYNCLINK_GENERIC_HDLC 165 #define dev_to_port(D) (dev_to_hdlc(D)->priv) 166 static void hdlcdev_tx_done(struct slgt_info *info); 167 static void hdlcdev_rx(struct slgt_info *info, char *buf, int size); 168 static int hdlcdev_init(struct slgt_info *info); 169 static void hdlcdev_exit(struct slgt_info *info); 170 #endif 171 172 173 /* 174 * device specific structures, macros and functions 175 */ 176 177 #define SLGT_MAX_PORTS 4 178 #define SLGT_REG_SIZE 256 179 180 /* 181 * conditional wait facility 182 */ 183 struct cond_wait { 184 struct cond_wait *next; 185 wait_queue_head_t q; 186 wait_queue_entry_t wait; 187 unsigned int data; 188 }; 189 static void init_cond_wait(struct cond_wait *w, unsigned int data); 190 static void add_cond_wait(struct cond_wait **head, struct cond_wait *w); 191 static void remove_cond_wait(struct cond_wait **head, struct cond_wait *w); 192 static void flush_cond_wait(struct cond_wait **head); 193 194 /* 195 * DMA buffer descriptor and access macros 196 */ 197 struct slgt_desc 198 { 199 __le16 count; 200 __le16 status; 201 __le32 pbuf; /* physical address of data buffer */ 202 __le32 next; /* physical address of next descriptor */ 203 204 /* driver book keeping */ 205 char *buf; /* virtual address of data buffer */ 206 unsigned int pdesc; /* physical address of this descriptor */ 207 dma_addr_t buf_dma_addr; 208 unsigned short buf_count; 209 }; 210 211 #define set_desc_buffer(a,b) (a).pbuf = cpu_to_le32((unsigned int)(b)) 212 #define set_desc_next(a,b) (a).next = cpu_to_le32((unsigned int)(b)) 213 #define set_desc_count(a,b)(a).count = cpu_to_le16((unsigned short)(b)) 214 #define set_desc_eof(a,b) (a).status = cpu_to_le16((b) ? (le16_to_cpu((a).status) | BIT0) : (le16_to_cpu((a).status) & ~BIT0)) 215 #define set_desc_status(a, b) (a).status = cpu_to_le16((unsigned short)(b)) 216 #define desc_count(a) (le16_to_cpu((a).count)) 217 #define desc_status(a) (le16_to_cpu((a).status)) 218 #define desc_complete(a) (le16_to_cpu((a).status) & BIT15) 219 #define desc_eof(a) (le16_to_cpu((a).status) & BIT2) 220 #define desc_crc_error(a) (le16_to_cpu((a).status) & BIT1) 221 #define desc_abort(a) (le16_to_cpu((a).status) & BIT0) 222 #define desc_residue(a) ((le16_to_cpu((a).status) & 0x38) >> 3) 223 224 struct _input_signal_events { 225 int ri_up; 226 int ri_down; 227 int dsr_up; 228 int dsr_down; 229 int dcd_up; 230 int dcd_down; 231 int cts_up; 232 int cts_down; 233 }; 234 235 /* 236 * device instance data structure 237 */ 238 struct slgt_info { 239 void *if_ptr; /* General purpose pointer (used by SPPP) */ 240 struct tty_port port; 241 242 struct slgt_info *next_device; /* device list link */ 243 244 int magic; 245 246 char device_name[25]; 247 struct pci_dev *pdev; 248 249 int port_count; /* count of ports on adapter */ 250 int adapter_num; /* adapter instance number */ 251 int port_num; /* port instance number */ 252 253 /* array of pointers to port contexts on this adapter */ 254 struct slgt_info *port_array[SLGT_MAX_PORTS]; 255 256 int line; /* tty line instance number */ 257 258 struct mgsl_icount icount; 259 260 int timeout; 261 int x_char; /* xon/xoff character */ 262 unsigned int read_status_mask; 263 unsigned int ignore_status_mask; 264 265 wait_queue_head_t status_event_wait_q; 266 wait_queue_head_t event_wait_q; 267 struct timer_list tx_timer; 268 struct timer_list rx_timer; 269 270 unsigned int gpio_present; 271 struct cond_wait *gpio_wait_q; 272 273 spinlock_t lock; /* spinlock for synchronizing with ISR */ 274 275 struct work_struct task; 276 u32 pending_bh; 277 bool bh_requested; 278 bool bh_running; 279 280 int isr_overflow; 281 bool irq_requested; /* true if IRQ requested */ 282 bool irq_occurred; /* for diagnostics use */ 283 284 /* device configuration */ 285 286 unsigned int bus_type; 287 unsigned int irq_level; 288 unsigned long irq_flags; 289 290 unsigned char __iomem * reg_addr; /* memory mapped registers address */ 291 u32 phys_reg_addr; 292 bool reg_addr_requested; 293 294 MGSL_PARAMS params; /* communications parameters */ 295 u32 idle_mode; 296 u32 max_frame_size; /* as set by device config */ 297 298 unsigned int rbuf_fill_level; 299 unsigned int rx_pio; 300 unsigned int if_mode; 301 unsigned int base_clock; 302 unsigned int xsync; 303 unsigned int xctrl; 304 305 /* device status */ 306 307 bool rx_enabled; 308 bool rx_restart; 309 310 bool tx_enabled; 311 bool tx_active; 312 313 unsigned char signals; /* serial signal states */ 314 int init_error; /* initialization error */ 315 316 unsigned char *tx_buf; 317 int tx_count; 318 319 char *flag_buf; 320 bool drop_rts_on_tx_done; 321 struct _input_signal_events input_signal_events; 322 323 int dcd_chkcount; /* check counts to prevent */ 324 int cts_chkcount; /* too many IRQs if a signal */ 325 int dsr_chkcount; /* is floating */ 326 int ri_chkcount; 327 328 char *bufs; /* virtual address of DMA buffer lists */ 329 dma_addr_t bufs_dma_addr; /* physical address of buffer descriptors */ 330 331 unsigned int rbuf_count; 332 struct slgt_desc *rbufs; 333 unsigned int rbuf_current; 334 unsigned int rbuf_index; 335 unsigned int rbuf_fill_index; 336 unsigned short rbuf_fill_count; 337 338 unsigned int tbuf_count; 339 struct slgt_desc *tbufs; 340 unsigned int tbuf_current; 341 unsigned int tbuf_start; 342 343 unsigned char *tmp_rbuf; 344 unsigned int tmp_rbuf_count; 345 346 /* SPPP/Cisco HDLC device parts */ 347 348 int netcount; 349 spinlock_t netlock; 350 #if SYNCLINK_GENERIC_HDLC 351 struct net_device *netdev; 352 #endif 353 354 }; 355 356 static MGSL_PARAMS default_params = { 357 .mode = MGSL_MODE_HDLC, 358 .loopback = 0, 359 .flags = HDLC_FLAG_UNDERRUN_ABORT15, 360 .encoding = HDLC_ENCODING_NRZI_SPACE, 361 .clock_speed = 0, 362 .addr_filter = 0xff, 363 .crc_type = HDLC_CRC_16_CCITT, 364 .preamble_length = HDLC_PREAMBLE_LENGTH_8BITS, 365 .preamble = HDLC_PREAMBLE_PATTERN_NONE, 366 .data_rate = 9600, 367 .data_bits = 8, 368 .stop_bits = 1, 369 .parity = ASYNC_PARITY_NONE 370 }; 371 372 373 #define BH_RECEIVE 1 374 #define BH_TRANSMIT 2 375 #define BH_STATUS 4 376 #define IO_PIN_SHUTDOWN_LIMIT 100 377 378 #define DMABUFSIZE 256 379 #define DESC_LIST_SIZE 4096 380 381 #define MASK_PARITY BIT1 382 #define MASK_FRAMING BIT0 383 #define MASK_BREAK BIT14 384 #define MASK_OVERRUN BIT4 385 386 #define GSR 0x00 /* global status */ 387 #define JCR 0x04 /* JTAG control */ 388 #define IODR 0x08 /* GPIO direction */ 389 #define IOER 0x0c /* GPIO interrupt enable */ 390 #define IOVR 0x10 /* GPIO value */ 391 #define IOSR 0x14 /* GPIO interrupt status */ 392 #define TDR 0x80 /* tx data */ 393 #define RDR 0x80 /* rx data */ 394 #define TCR 0x82 /* tx control */ 395 #define TIR 0x84 /* tx idle */ 396 #define TPR 0x85 /* tx preamble */ 397 #define RCR 0x86 /* rx control */ 398 #define VCR 0x88 /* V.24 control */ 399 #define CCR 0x89 /* clock control */ 400 #define BDR 0x8a /* baud divisor */ 401 #define SCR 0x8c /* serial control */ 402 #define SSR 0x8e /* serial status */ 403 #define RDCSR 0x90 /* rx DMA control/status */ 404 #define TDCSR 0x94 /* tx DMA control/status */ 405 #define RDDAR 0x98 /* rx DMA descriptor address */ 406 #define TDDAR 0x9c /* tx DMA descriptor address */ 407 #define XSR 0x40 /* extended sync pattern */ 408 #define XCR 0x44 /* extended control */ 409 410 #define RXIDLE BIT14 411 #define RXBREAK BIT14 412 #define IRQ_TXDATA BIT13 413 #define IRQ_TXIDLE BIT12 414 #define IRQ_TXUNDER BIT11 /* HDLC */ 415 #define IRQ_RXDATA BIT10 416 #define IRQ_RXIDLE BIT9 /* HDLC */ 417 #define IRQ_RXBREAK BIT9 /* async */ 418 #define IRQ_RXOVER BIT8 419 #define IRQ_DSR BIT7 420 #define IRQ_CTS BIT6 421 #define IRQ_DCD BIT5 422 #define IRQ_RI BIT4 423 #define IRQ_ALL 0x3ff0 424 #define IRQ_MASTER BIT0 425 426 #define slgt_irq_on(info, mask) \ 427 wr_reg16((info), SCR, (unsigned short)(rd_reg16((info), SCR) | (mask))) 428 #define slgt_irq_off(info, mask) \ 429 wr_reg16((info), SCR, (unsigned short)(rd_reg16((info), SCR) & ~(mask))) 430 431 static __u8 rd_reg8(struct slgt_info *info, unsigned int addr); 432 static void wr_reg8(struct slgt_info *info, unsigned int addr, __u8 value); 433 static __u16 rd_reg16(struct slgt_info *info, unsigned int addr); 434 static void wr_reg16(struct slgt_info *info, unsigned int addr, __u16 value); 435 static __u32 rd_reg32(struct slgt_info *info, unsigned int addr); 436 static void wr_reg32(struct slgt_info *info, unsigned int addr, __u32 value); 437 438 static void msc_set_vcr(struct slgt_info *info); 439 440 static int startup(struct slgt_info *info); 441 static int block_til_ready(struct tty_struct *tty, struct file * filp,struct slgt_info *info); 442 static void shutdown(struct slgt_info *info); 443 static void program_hw(struct slgt_info *info); 444 static void change_params(struct slgt_info *info); 445 446 static int register_test(struct slgt_info *info); 447 static int irq_test(struct slgt_info *info); 448 static int loopback_test(struct slgt_info *info); 449 static int adapter_test(struct slgt_info *info); 450 451 static void reset_adapter(struct slgt_info *info); 452 static void reset_port(struct slgt_info *info); 453 static void async_mode(struct slgt_info *info); 454 static void sync_mode(struct slgt_info *info); 455 456 static void rx_stop(struct slgt_info *info); 457 static void rx_start(struct slgt_info *info); 458 static void reset_rbufs(struct slgt_info *info); 459 static void free_rbufs(struct slgt_info *info, unsigned int first, unsigned int last); 460 static void rdma_reset(struct slgt_info *info); 461 static bool rx_get_frame(struct slgt_info *info); 462 static bool rx_get_buf(struct slgt_info *info); 463 464 static void tx_start(struct slgt_info *info); 465 static void tx_stop(struct slgt_info *info); 466 static void tx_set_idle(struct slgt_info *info); 467 static unsigned int free_tbuf_count(struct slgt_info *info); 468 static unsigned int tbuf_bytes(struct slgt_info *info); 469 static void reset_tbufs(struct slgt_info *info); 470 static void tdma_reset(struct slgt_info *info); 471 static bool tx_load(struct slgt_info *info, const char *buf, unsigned int count); 472 473 static void get_signals(struct slgt_info *info); 474 static void set_signals(struct slgt_info *info); 475 static void enable_loopback(struct slgt_info *info); 476 static void set_rate(struct slgt_info *info, u32 data_rate); 477 478 static int bh_action(struct slgt_info *info); 479 static void bh_handler(struct work_struct *work); 480 static void bh_transmit(struct slgt_info *info); 481 static void isr_serial(struct slgt_info *info); 482 static void isr_rdma(struct slgt_info *info); 483 static void isr_txeom(struct slgt_info *info, unsigned short status); 484 static void isr_tdma(struct slgt_info *info); 485 486 static int alloc_dma_bufs(struct slgt_info *info); 487 static void free_dma_bufs(struct slgt_info *info); 488 static int alloc_desc(struct slgt_info *info); 489 static void free_desc(struct slgt_info *info); 490 static int alloc_bufs(struct slgt_info *info, struct slgt_desc *bufs, int count); 491 static void free_bufs(struct slgt_info *info, struct slgt_desc *bufs, int count); 492 493 static int alloc_tmp_rbuf(struct slgt_info *info); 494 static void free_tmp_rbuf(struct slgt_info *info); 495 496 static void tx_timeout(struct timer_list *t); 497 static void rx_timeout(struct timer_list *t); 498 499 /* 500 * ioctl handlers 501 */ 502 static int get_stats(struct slgt_info *info, struct mgsl_icount __user *user_icount); 503 static int get_params(struct slgt_info *info, MGSL_PARAMS __user *params); 504 static int set_params(struct slgt_info *info, MGSL_PARAMS __user *params); 505 static int get_txidle(struct slgt_info *info, int __user *idle_mode); 506 static int set_txidle(struct slgt_info *info, int idle_mode); 507 static int tx_enable(struct slgt_info *info, int enable); 508 static int tx_abort(struct slgt_info *info); 509 static int rx_enable(struct slgt_info *info, int enable); 510 static int modem_input_wait(struct slgt_info *info,int arg); 511 static int wait_mgsl_event(struct slgt_info *info, int __user *mask_ptr); 512 static int tiocmget(struct tty_struct *tty); 513 static int tiocmset(struct tty_struct *tty, 514 unsigned int set, unsigned int clear); 515 static int set_break(struct tty_struct *tty, int break_state); 516 static int get_interface(struct slgt_info *info, int __user *if_mode); 517 static int set_interface(struct slgt_info *info, int if_mode); 518 static int set_gpio(struct slgt_info *info, struct gpio_desc __user *gpio); 519 static int get_gpio(struct slgt_info *info, struct gpio_desc __user *gpio); 520 static int wait_gpio(struct slgt_info *info, struct gpio_desc __user *gpio); 521 static int get_xsync(struct slgt_info *info, int __user *if_mode); 522 static int set_xsync(struct slgt_info *info, int if_mode); 523 static int get_xctrl(struct slgt_info *info, int __user *if_mode); 524 static int set_xctrl(struct slgt_info *info, int if_mode); 525 526 /* 527 * driver functions 528 */ 529 static void add_device(struct slgt_info *info); 530 static void device_init(int adapter_num, struct pci_dev *pdev); 531 static int claim_resources(struct slgt_info *info); 532 static void release_resources(struct slgt_info *info); 533 534 /* 535 * DEBUG OUTPUT CODE 536 */ 537 #ifndef DBGINFO 538 #define DBGINFO(fmt) 539 #endif 540 #ifndef DBGERR 541 #define DBGERR(fmt) 542 #endif 543 #ifndef DBGBH 544 #define DBGBH(fmt) 545 #endif 546 #ifndef DBGISR 547 #define DBGISR(fmt) 548 #endif 549 550 #ifdef DBGDATA 551 static void trace_block(struct slgt_info *info, const char *data, int count, const char *label) 552 { 553 int i; 554 int linecount; 555 printk("%s %s data:\n",info->device_name, label); 556 while(count) { 557 linecount = (count > 16) ? 16 : count; 558 for(i=0; i < linecount; i++) 559 printk("%02X ",(unsigned char)data[i]); 560 for(;i<17;i++) 561 printk(" "); 562 for(i=0;i<linecount;i++) { 563 if (data[i]>=040 && data[i]<=0176) 564 printk("%c",data[i]); 565 else 566 printk("."); 567 } 568 printk("\n"); 569 data += linecount; 570 count -= linecount; 571 } 572 } 573 #else 574 #define DBGDATA(info, buf, size, label) 575 #endif 576 577 #ifdef DBGTBUF 578 static void dump_tbufs(struct slgt_info *info) 579 { 580 int i; 581 printk("tbuf_current=%d\n", info->tbuf_current); 582 for (i=0 ; i < info->tbuf_count ; i++) { 583 printk("%d: count=%04X status=%04X\n", 584 i, le16_to_cpu(info->tbufs[i].count), le16_to_cpu(info->tbufs[i].status)); 585 } 586 } 587 #else 588 #define DBGTBUF(info) 589 #endif 590 591 #ifdef DBGRBUF 592 static void dump_rbufs(struct slgt_info *info) 593 { 594 int i; 595 printk("rbuf_current=%d\n", info->rbuf_current); 596 for (i=0 ; i < info->rbuf_count ; i++) { 597 printk("%d: count=%04X status=%04X\n", 598 i, le16_to_cpu(info->rbufs[i].count), le16_to_cpu(info->rbufs[i].status)); 599 } 600 } 601 #else 602 #define DBGRBUF(info) 603 #endif 604 605 static inline int sanity_check(struct slgt_info *info, char *devname, const char *name) 606 { 607 #ifdef SANITY_CHECK 608 if (!info) { 609 printk("null struct slgt_info for (%s) in %s\n", devname, name); 610 return 1; 611 } 612 if (info->magic != MGSL_MAGIC) { 613 printk("bad magic number struct slgt_info (%s) in %s\n", devname, name); 614 return 1; 615 } 616 #else 617 if (!info) 618 return 1; 619 #endif 620 return 0; 621 } 622 623 /** 624 * line discipline callback wrappers 625 * 626 * The wrappers maintain line discipline references 627 * while calling into the line discipline. 628 * 629 * ldisc_receive_buf - pass receive data to line discipline 630 */ 631 static void ldisc_receive_buf(struct tty_struct *tty, 632 const __u8 *data, char *flags, int count) 633 { 634 struct tty_ldisc *ld; 635 if (!tty) 636 return; 637 ld = tty_ldisc_ref(tty); 638 if (ld) { 639 if (ld->ops->receive_buf) 640 ld->ops->receive_buf(tty, data, flags, count); 641 tty_ldisc_deref(ld); 642 } 643 } 644 645 /* tty callbacks */ 646 647 static int open(struct tty_struct *tty, struct file *filp) 648 { 649 struct slgt_info *info; 650 int retval, line; 651 unsigned long flags; 652 653 line = tty->index; 654 if (line >= slgt_device_count) { 655 DBGERR(("%s: open with invalid line #%d.\n", driver_name, line)); 656 return -ENODEV; 657 } 658 659 info = slgt_device_list; 660 while(info && info->line != line) 661 info = info->next_device; 662 if (sanity_check(info, tty->name, "open")) 663 return -ENODEV; 664 if (info->init_error) { 665 DBGERR(("%s init error=%d\n", info->device_name, info->init_error)); 666 return -ENODEV; 667 } 668 669 tty->driver_data = info; 670 info->port.tty = tty; 671 672 DBGINFO(("%s open, old ref count = %d\n", info->device_name, info->port.count)); 673 674 mutex_lock(&info->port.mutex); 675 info->port.low_latency = (info->port.flags & ASYNC_LOW_LATENCY) ? 1 : 0; 676 677 spin_lock_irqsave(&info->netlock, flags); 678 if (info->netcount) { 679 retval = -EBUSY; 680 spin_unlock_irqrestore(&info->netlock, flags); 681 mutex_unlock(&info->port.mutex); 682 goto cleanup; 683 } 684 info->port.count++; 685 spin_unlock_irqrestore(&info->netlock, flags); 686 687 if (info->port.count == 1) { 688 /* 1st open on this device, init hardware */ 689 retval = startup(info); 690 if (retval < 0) { 691 mutex_unlock(&info->port.mutex); 692 goto cleanup; 693 } 694 } 695 mutex_unlock(&info->port.mutex); 696 retval = block_til_ready(tty, filp, info); 697 if (retval) { 698 DBGINFO(("%s block_til_ready rc=%d\n", info->device_name, retval)); 699 goto cleanup; 700 } 701 702 retval = 0; 703 704 cleanup: 705 if (retval) { 706 if (tty->count == 1) 707 info->port.tty = NULL; /* tty layer will release tty struct */ 708 if(info->port.count) 709 info->port.count--; 710 } 711 712 DBGINFO(("%s open rc=%d\n", info->device_name, retval)); 713 return retval; 714 } 715 716 static void close(struct tty_struct *tty, struct file *filp) 717 { 718 struct slgt_info *info = tty->driver_data; 719 720 if (sanity_check(info, tty->name, "close")) 721 return; 722 DBGINFO(("%s close entry, count=%d\n", info->device_name, info->port.count)); 723 724 if (tty_port_close_start(&info->port, tty, filp) == 0) 725 goto cleanup; 726 727 mutex_lock(&info->port.mutex); 728 if (tty_port_initialized(&info->port)) 729 wait_until_sent(tty, info->timeout); 730 flush_buffer(tty); 731 tty_ldisc_flush(tty); 732 733 shutdown(info); 734 mutex_unlock(&info->port.mutex); 735 736 tty_port_close_end(&info->port, tty); 737 info->port.tty = NULL; 738 cleanup: 739 DBGINFO(("%s close exit, count=%d\n", tty->driver->name, info->port.count)); 740 } 741 742 static void hangup(struct tty_struct *tty) 743 { 744 struct slgt_info *info = tty->driver_data; 745 unsigned long flags; 746 747 if (sanity_check(info, tty->name, "hangup")) 748 return; 749 DBGINFO(("%s hangup\n", info->device_name)); 750 751 flush_buffer(tty); 752 753 mutex_lock(&info->port.mutex); 754 shutdown(info); 755 756 spin_lock_irqsave(&info->port.lock, flags); 757 info->port.count = 0; 758 info->port.tty = NULL; 759 spin_unlock_irqrestore(&info->port.lock, flags); 760 tty_port_set_active(&info->port, 0); 761 mutex_unlock(&info->port.mutex); 762 763 wake_up_interruptible(&info->port.open_wait); 764 } 765 766 static void set_termios(struct tty_struct *tty, struct ktermios *old_termios) 767 { 768 struct slgt_info *info = tty->driver_data; 769 unsigned long flags; 770 771 DBGINFO(("%s set_termios\n", tty->driver->name)); 772 773 change_params(info); 774 775 /* Handle transition to B0 status */ 776 if ((old_termios->c_cflag & CBAUD) && !C_BAUD(tty)) { 777 info->signals &= ~(SerialSignal_RTS | SerialSignal_DTR); 778 spin_lock_irqsave(&info->lock,flags); 779 set_signals(info); 780 spin_unlock_irqrestore(&info->lock,flags); 781 } 782 783 /* Handle transition away from B0 status */ 784 if (!(old_termios->c_cflag & CBAUD) && C_BAUD(tty)) { 785 info->signals |= SerialSignal_DTR; 786 if (!C_CRTSCTS(tty) || !tty_throttled(tty)) 787 info->signals |= SerialSignal_RTS; 788 spin_lock_irqsave(&info->lock,flags); 789 set_signals(info); 790 spin_unlock_irqrestore(&info->lock,flags); 791 } 792 793 /* Handle turning off CRTSCTS */ 794 if ((old_termios->c_cflag & CRTSCTS) && !C_CRTSCTS(tty)) { 795 tty->hw_stopped = 0; 796 tx_release(tty); 797 } 798 } 799 800 static void update_tx_timer(struct slgt_info *info) 801 { 802 /* 803 * use worst case speed of 1200bps to calculate transmit timeout 804 * based on data in buffers (tbuf_bytes) and FIFO (128 bytes) 805 */ 806 if (info->params.mode == MGSL_MODE_HDLC) { 807 int timeout = (tbuf_bytes(info) * 7) + 1000; 808 mod_timer(&info->tx_timer, jiffies + msecs_to_jiffies(timeout)); 809 } 810 } 811 812 static int write(struct tty_struct *tty, 813 const unsigned char *buf, int count) 814 { 815 int ret = 0; 816 struct slgt_info *info = tty->driver_data; 817 unsigned long flags; 818 819 if (sanity_check(info, tty->name, "write")) 820 return -EIO; 821 822 DBGINFO(("%s write count=%d\n", info->device_name, count)); 823 824 if (!info->tx_buf || (count > info->max_frame_size)) 825 return -EIO; 826 827 if (!count || tty->stopped || tty->hw_stopped) 828 return 0; 829 830 spin_lock_irqsave(&info->lock, flags); 831 832 if (info->tx_count) { 833 /* send accumulated data from send_char() */ 834 if (!tx_load(info, info->tx_buf, info->tx_count)) 835 goto cleanup; 836 info->tx_count = 0; 837 } 838 839 if (tx_load(info, buf, count)) 840 ret = count; 841 842 cleanup: 843 spin_unlock_irqrestore(&info->lock, flags); 844 DBGINFO(("%s write rc=%d\n", info->device_name, ret)); 845 return ret; 846 } 847 848 static int put_char(struct tty_struct *tty, unsigned char ch) 849 { 850 struct slgt_info *info = tty->driver_data; 851 unsigned long flags; 852 int ret = 0; 853 854 if (sanity_check(info, tty->name, "put_char")) 855 return 0; 856 DBGINFO(("%s put_char(%d)\n", info->device_name, ch)); 857 if (!info->tx_buf) 858 return 0; 859 spin_lock_irqsave(&info->lock,flags); 860 if (info->tx_count < info->max_frame_size) { 861 info->tx_buf[info->tx_count++] = ch; 862 ret = 1; 863 } 864 spin_unlock_irqrestore(&info->lock,flags); 865 return ret; 866 } 867 868 static void send_xchar(struct tty_struct *tty, char ch) 869 { 870 struct slgt_info *info = tty->driver_data; 871 unsigned long flags; 872 873 if (sanity_check(info, tty->name, "send_xchar")) 874 return; 875 DBGINFO(("%s send_xchar(%d)\n", info->device_name, ch)); 876 info->x_char = ch; 877 if (ch) { 878 spin_lock_irqsave(&info->lock,flags); 879 if (!info->tx_enabled) 880 tx_start(info); 881 spin_unlock_irqrestore(&info->lock,flags); 882 } 883 } 884 885 static void wait_until_sent(struct tty_struct *tty, int timeout) 886 { 887 struct slgt_info *info = tty->driver_data; 888 unsigned long orig_jiffies, char_time; 889 890 if (!info ) 891 return; 892 if (sanity_check(info, tty->name, "wait_until_sent")) 893 return; 894 DBGINFO(("%s wait_until_sent entry\n", info->device_name)); 895 if (!tty_port_initialized(&info->port)) 896 goto exit; 897 898 orig_jiffies = jiffies; 899 900 /* Set check interval to 1/5 of estimated time to 901 * send a character, and make it at least 1. The check 902 * interval should also be less than the timeout. 903 * Note: use tight timings here to satisfy the NIST-PCTS. 904 */ 905 906 if (info->params.data_rate) { 907 char_time = info->timeout/(32 * 5); 908 if (!char_time) 909 char_time++; 910 } else 911 char_time = 1; 912 913 if (timeout) 914 char_time = min_t(unsigned long, char_time, timeout); 915 916 while (info->tx_active) { 917 msleep_interruptible(jiffies_to_msecs(char_time)); 918 if (signal_pending(current)) 919 break; 920 if (timeout && time_after(jiffies, orig_jiffies + timeout)) 921 break; 922 } 923 exit: 924 DBGINFO(("%s wait_until_sent exit\n", info->device_name)); 925 } 926 927 static int write_room(struct tty_struct *tty) 928 { 929 struct slgt_info *info = tty->driver_data; 930 int ret; 931 932 if (sanity_check(info, tty->name, "write_room")) 933 return 0; 934 ret = (info->tx_active) ? 0 : HDLC_MAX_FRAME_SIZE; 935 DBGINFO(("%s write_room=%d\n", info->device_name, ret)); 936 return ret; 937 } 938 939 static void flush_chars(struct tty_struct *tty) 940 { 941 struct slgt_info *info = tty->driver_data; 942 unsigned long flags; 943 944 if (sanity_check(info, tty->name, "flush_chars")) 945 return; 946 DBGINFO(("%s flush_chars entry tx_count=%d\n", info->device_name, info->tx_count)); 947 948 if (info->tx_count <= 0 || tty->stopped || 949 tty->hw_stopped || !info->tx_buf) 950 return; 951 952 DBGINFO(("%s flush_chars start transmit\n", info->device_name)); 953 954 spin_lock_irqsave(&info->lock,flags); 955 if (info->tx_count && tx_load(info, info->tx_buf, info->tx_count)) 956 info->tx_count = 0; 957 spin_unlock_irqrestore(&info->lock,flags); 958 } 959 960 static void flush_buffer(struct tty_struct *tty) 961 { 962 struct slgt_info *info = tty->driver_data; 963 unsigned long flags; 964 965 if (sanity_check(info, tty->name, "flush_buffer")) 966 return; 967 DBGINFO(("%s flush_buffer\n", info->device_name)); 968 969 spin_lock_irqsave(&info->lock, flags); 970 info->tx_count = 0; 971 spin_unlock_irqrestore(&info->lock, flags); 972 973 tty_wakeup(tty); 974 } 975 976 /* 977 * throttle (stop) transmitter 978 */ 979 static void tx_hold(struct tty_struct *tty) 980 { 981 struct slgt_info *info = tty->driver_data; 982 unsigned long flags; 983 984 if (sanity_check(info, tty->name, "tx_hold")) 985 return; 986 DBGINFO(("%s tx_hold\n", info->device_name)); 987 spin_lock_irqsave(&info->lock,flags); 988 if (info->tx_enabled && info->params.mode == MGSL_MODE_ASYNC) 989 tx_stop(info); 990 spin_unlock_irqrestore(&info->lock,flags); 991 } 992 993 /* 994 * release (start) transmitter 995 */ 996 static void tx_release(struct tty_struct *tty) 997 { 998 struct slgt_info *info = tty->driver_data; 999 unsigned long flags; 1000 1001 if (sanity_check(info, tty->name, "tx_release")) 1002 return; 1003 DBGINFO(("%s tx_release\n", info->device_name)); 1004 spin_lock_irqsave(&info->lock, flags); 1005 if (info->tx_count && tx_load(info, info->tx_buf, info->tx_count)) 1006 info->tx_count = 0; 1007 spin_unlock_irqrestore(&info->lock, flags); 1008 } 1009 1010 /* 1011 * Service an IOCTL request 1012 * 1013 * Arguments 1014 * 1015 * tty pointer to tty instance data 1016 * cmd IOCTL command code 1017 * arg command argument/context 1018 * 1019 * Return 0 if success, otherwise error code 1020 */ 1021 static int ioctl(struct tty_struct *tty, 1022 unsigned int cmd, unsigned long arg) 1023 { 1024 struct slgt_info *info = tty->driver_data; 1025 void __user *argp = (void __user *)arg; 1026 int ret; 1027 1028 if (sanity_check(info, tty->name, "ioctl")) 1029 return -ENODEV; 1030 DBGINFO(("%s ioctl() cmd=%08X\n", info->device_name, cmd)); 1031 1032 if (cmd != TIOCMIWAIT) { 1033 if (tty_io_error(tty)) 1034 return -EIO; 1035 } 1036 1037 switch (cmd) { 1038 case MGSL_IOCWAITEVENT: 1039 return wait_mgsl_event(info, argp); 1040 case TIOCMIWAIT: 1041 return modem_input_wait(info,(int)arg); 1042 case MGSL_IOCSGPIO: 1043 return set_gpio(info, argp); 1044 case MGSL_IOCGGPIO: 1045 return get_gpio(info, argp); 1046 case MGSL_IOCWAITGPIO: 1047 return wait_gpio(info, argp); 1048 case MGSL_IOCGXSYNC: 1049 return get_xsync(info, argp); 1050 case MGSL_IOCSXSYNC: 1051 return set_xsync(info, (int)arg); 1052 case MGSL_IOCGXCTRL: 1053 return get_xctrl(info, argp); 1054 case MGSL_IOCSXCTRL: 1055 return set_xctrl(info, (int)arg); 1056 } 1057 mutex_lock(&info->port.mutex); 1058 switch (cmd) { 1059 case MGSL_IOCGPARAMS: 1060 ret = get_params(info, argp); 1061 break; 1062 case MGSL_IOCSPARAMS: 1063 ret = set_params(info, argp); 1064 break; 1065 case MGSL_IOCGTXIDLE: 1066 ret = get_txidle(info, argp); 1067 break; 1068 case MGSL_IOCSTXIDLE: 1069 ret = set_txidle(info, (int)arg); 1070 break; 1071 case MGSL_IOCTXENABLE: 1072 ret = tx_enable(info, (int)arg); 1073 break; 1074 case MGSL_IOCRXENABLE: 1075 ret = rx_enable(info, (int)arg); 1076 break; 1077 case MGSL_IOCTXABORT: 1078 ret = tx_abort(info); 1079 break; 1080 case MGSL_IOCGSTATS: 1081 ret = get_stats(info, argp); 1082 break; 1083 case MGSL_IOCGIF: 1084 ret = get_interface(info, argp); 1085 break; 1086 case MGSL_IOCSIF: 1087 ret = set_interface(info,(int)arg); 1088 break; 1089 default: 1090 ret = -ENOIOCTLCMD; 1091 } 1092 mutex_unlock(&info->port.mutex); 1093 return ret; 1094 } 1095 1096 static int get_icount(struct tty_struct *tty, 1097 struct serial_icounter_struct *icount) 1098 1099 { 1100 struct slgt_info *info = tty->driver_data; 1101 struct mgsl_icount cnow; /* kernel counter temps */ 1102 unsigned long flags; 1103 1104 spin_lock_irqsave(&info->lock,flags); 1105 cnow = info->icount; 1106 spin_unlock_irqrestore(&info->lock,flags); 1107 1108 icount->cts = cnow.cts; 1109 icount->dsr = cnow.dsr; 1110 icount->rng = cnow.rng; 1111 icount->dcd = cnow.dcd; 1112 icount->rx = cnow.rx; 1113 icount->tx = cnow.tx; 1114 icount->frame = cnow.frame; 1115 icount->overrun = cnow.overrun; 1116 icount->parity = cnow.parity; 1117 icount->brk = cnow.brk; 1118 icount->buf_overrun = cnow.buf_overrun; 1119 1120 return 0; 1121 } 1122 1123 /* 1124 * support for 32 bit ioctl calls on 64 bit systems 1125 */ 1126 #ifdef CONFIG_COMPAT 1127 static long get_params32(struct slgt_info *info, struct MGSL_PARAMS32 __user *user_params) 1128 { 1129 struct MGSL_PARAMS32 tmp_params; 1130 1131 DBGINFO(("%s get_params32\n", info->device_name)); 1132 memset(&tmp_params, 0, sizeof(tmp_params)); 1133 tmp_params.mode = (compat_ulong_t)info->params.mode; 1134 tmp_params.loopback = info->params.loopback; 1135 tmp_params.flags = info->params.flags; 1136 tmp_params.encoding = info->params.encoding; 1137 tmp_params.clock_speed = (compat_ulong_t)info->params.clock_speed; 1138 tmp_params.addr_filter = info->params.addr_filter; 1139 tmp_params.crc_type = info->params.crc_type; 1140 tmp_params.preamble_length = info->params.preamble_length; 1141 tmp_params.preamble = info->params.preamble; 1142 tmp_params.data_rate = (compat_ulong_t)info->params.data_rate; 1143 tmp_params.data_bits = info->params.data_bits; 1144 tmp_params.stop_bits = info->params.stop_bits; 1145 tmp_params.parity = info->params.parity; 1146 if (copy_to_user(user_params, &tmp_params, sizeof(struct MGSL_PARAMS32))) 1147 return -EFAULT; 1148 return 0; 1149 } 1150 1151 static long set_params32(struct slgt_info *info, struct MGSL_PARAMS32 __user *new_params) 1152 { 1153 struct MGSL_PARAMS32 tmp_params; 1154 1155 DBGINFO(("%s set_params32\n", info->device_name)); 1156 if (copy_from_user(&tmp_params, new_params, sizeof(struct MGSL_PARAMS32))) 1157 return -EFAULT; 1158 1159 spin_lock(&info->lock); 1160 if (tmp_params.mode == MGSL_MODE_BASE_CLOCK) { 1161 info->base_clock = tmp_params.clock_speed; 1162 } else { 1163 info->params.mode = tmp_params.mode; 1164 info->params.loopback = tmp_params.loopback; 1165 info->params.flags = tmp_params.flags; 1166 info->params.encoding = tmp_params.encoding; 1167 info->params.clock_speed = tmp_params.clock_speed; 1168 info->params.addr_filter = tmp_params.addr_filter; 1169 info->params.crc_type = tmp_params.crc_type; 1170 info->params.preamble_length = tmp_params.preamble_length; 1171 info->params.preamble = tmp_params.preamble; 1172 info->params.data_rate = tmp_params.data_rate; 1173 info->params.data_bits = tmp_params.data_bits; 1174 info->params.stop_bits = tmp_params.stop_bits; 1175 info->params.parity = tmp_params.parity; 1176 } 1177 spin_unlock(&info->lock); 1178 1179 program_hw(info); 1180 1181 return 0; 1182 } 1183 1184 static long slgt_compat_ioctl(struct tty_struct *tty, 1185 unsigned int cmd, unsigned long arg) 1186 { 1187 struct slgt_info *info = tty->driver_data; 1188 int rc; 1189 1190 if (sanity_check(info, tty->name, "compat_ioctl")) 1191 return -ENODEV; 1192 DBGINFO(("%s compat_ioctl() cmd=%08X\n", info->device_name, cmd)); 1193 1194 switch (cmd) { 1195 case MGSL_IOCSPARAMS32: 1196 rc = set_params32(info, compat_ptr(arg)); 1197 break; 1198 1199 case MGSL_IOCGPARAMS32: 1200 rc = get_params32(info, compat_ptr(arg)); 1201 break; 1202 1203 case MGSL_IOCGPARAMS: 1204 case MGSL_IOCSPARAMS: 1205 case MGSL_IOCGTXIDLE: 1206 case MGSL_IOCGSTATS: 1207 case MGSL_IOCWAITEVENT: 1208 case MGSL_IOCGIF: 1209 case MGSL_IOCSGPIO: 1210 case MGSL_IOCGGPIO: 1211 case MGSL_IOCWAITGPIO: 1212 case MGSL_IOCGXSYNC: 1213 case MGSL_IOCGXCTRL: 1214 rc = ioctl(tty, cmd, (unsigned long)compat_ptr(arg)); 1215 break; 1216 default: 1217 rc = ioctl(tty, cmd, arg); 1218 } 1219 DBGINFO(("%s compat_ioctl() cmd=%08X rc=%d\n", info->device_name, cmd, rc)); 1220 return rc; 1221 } 1222 #else 1223 #define slgt_compat_ioctl NULL 1224 #endif /* ifdef CONFIG_COMPAT */ 1225 1226 /* 1227 * proc fs support 1228 */ 1229 static inline void line_info(struct seq_file *m, struct slgt_info *info) 1230 { 1231 char stat_buf[30]; 1232 unsigned long flags; 1233 1234 seq_printf(m, "%s: IO=%08X IRQ=%d MaxFrameSize=%u\n", 1235 info->device_name, info->phys_reg_addr, 1236 info->irq_level, info->max_frame_size); 1237 1238 /* output current serial signal states */ 1239 spin_lock_irqsave(&info->lock,flags); 1240 get_signals(info); 1241 spin_unlock_irqrestore(&info->lock,flags); 1242 1243 stat_buf[0] = 0; 1244 stat_buf[1] = 0; 1245 if (info->signals & SerialSignal_RTS) 1246 strcat(stat_buf, "|RTS"); 1247 if (info->signals & SerialSignal_CTS) 1248 strcat(stat_buf, "|CTS"); 1249 if (info->signals & SerialSignal_DTR) 1250 strcat(stat_buf, "|DTR"); 1251 if (info->signals & SerialSignal_DSR) 1252 strcat(stat_buf, "|DSR"); 1253 if (info->signals & SerialSignal_DCD) 1254 strcat(stat_buf, "|CD"); 1255 if (info->signals & SerialSignal_RI) 1256 strcat(stat_buf, "|RI"); 1257 1258 if (info->params.mode != MGSL_MODE_ASYNC) { 1259 seq_printf(m, "\tHDLC txok:%d rxok:%d", 1260 info->icount.txok, info->icount.rxok); 1261 if (info->icount.txunder) 1262 seq_printf(m, " txunder:%d", info->icount.txunder); 1263 if (info->icount.txabort) 1264 seq_printf(m, " txabort:%d", info->icount.txabort); 1265 if (info->icount.rxshort) 1266 seq_printf(m, " rxshort:%d", info->icount.rxshort); 1267 if (info->icount.rxlong) 1268 seq_printf(m, " rxlong:%d", info->icount.rxlong); 1269 if (info->icount.rxover) 1270 seq_printf(m, " rxover:%d", info->icount.rxover); 1271 if (info->icount.rxcrc) 1272 seq_printf(m, " rxcrc:%d", info->icount.rxcrc); 1273 } else { 1274 seq_printf(m, "\tASYNC tx:%d rx:%d", 1275 info->icount.tx, info->icount.rx); 1276 if (info->icount.frame) 1277 seq_printf(m, " fe:%d", info->icount.frame); 1278 if (info->icount.parity) 1279 seq_printf(m, " pe:%d", info->icount.parity); 1280 if (info->icount.brk) 1281 seq_printf(m, " brk:%d", info->icount.brk); 1282 if (info->icount.overrun) 1283 seq_printf(m, " oe:%d", info->icount.overrun); 1284 } 1285 1286 /* Append serial signal status to end */ 1287 seq_printf(m, " %s\n", stat_buf+1); 1288 1289 seq_printf(m, "\ttxactive=%d bh_req=%d bh_run=%d pending_bh=%x\n", 1290 info->tx_active,info->bh_requested,info->bh_running, 1291 info->pending_bh); 1292 } 1293 1294 /* Called to print information about devices 1295 */ 1296 static int synclink_gt_proc_show(struct seq_file *m, void *v) 1297 { 1298 struct slgt_info *info; 1299 1300 seq_puts(m, "synclink_gt driver\n"); 1301 1302 info = slgt_device_list; 1303 while( info ) { 1304 line_info(m, info); 1305 info = info->next_device; 1306 } 1307 return 0; 1308 } 1309 1310 /* 1311 * return count of bytes in transmit buffer 1312 */ 1313 static int chars_in_buffer(struct tty_struct *tty) 1314 { 1315 struct slgt_info *info = tty->driver_data; 1316 int count; 1317 if (sanity_check(info, tty->name, "chars_in_buffer")) 1318 return 0; 1319 count = tbuf_bytes(info); 1320 DBGINFO(("%s chars_in_buffer()=%d\n", info->device_name, count)); 1321 return count; 1322 } 1323 1324 /* 1325 * signal remote device to throttle send data (our receive data) 1326 */ 1327 static void throttle(struct tty_struct * tty) 1328 { 1329 struct slgt_info *info = tty->driver_data; 1330 unsigned long flags; 1331 1332 if (sanity_check(info, tty->name, "throttle")) 1333 return; 1334 DBGINFO(("%s throttle\n", info->device_name)); 1335 if (I_IXOFF(tty)) 1336 send_xchar(tty, STOP_CHAR(tty)); 1337 if (C_CRTSCTS(tty)) { 1338 spin_lock_irqsave(&info->lock,flags); 1339 info->signals &= ~SerialSignal_RTS; 1340 set_signals(info); 1341 spin_unlock_irqrestore(&info->lock,flags); 1342 } 1343 } 1344 1345 /* 1346 * signal remote device to stop throttling send data (our receive data) 1347 */ 1348 static void unthrottle(struct tty_struct * tty) 1349 { 1350 struct slgt_info *info = tty->driver_data; 1351 unsigned long flags; 1352 1353 if (sanity_check(info, tty->name, "unthrottle")) 1354 return; 1355 DBGINFO(("%s unthrottle\n", info->device_name)); 1356 if (I_IXOFF(tty)) { 1357 if (info->x_char) 1358 info->x_char = 0; 1359 else 1360 send_xchar(tty, START_CHAR(tty)); 1361 } 1362 if (C_CRTSCTS(tty)) { 1363 spin_lock_irqsave(&info->lock,flags); 1364 info->signals |= SerialSignal_RTS; 1365 set_signals(info); 1366 spin_unlock_irqrestore(&info->lock,flags); 1367 } 1368 } 1369 1370 /* 1371 * set or clear transmit break condition 1372 * break_state -1=set break condition, 0=clear 1373 */ 1374 static int set_break(struct tty_struct *tty, int break_state) 1375 { 1376 struct slgt_info *info = tty->driver_data; 1377 unsigned short value; 1378 unsigned long flags; 1379 1380 if (sanity_check(info, tty->name, "set_break")) 1381 return -EINVAL; 1382 DBGINFO(("%s set_break(%d)\n", info->device_name, break_state)); 1383 1384 spin_lock_irqsave(&info->lock,flags); 1385 value = rd_reg16(info, TCR); 1386 if (break_state == -1) 1387 value |= BIT6; 1388 else 1389 value &= ~BIT6; 1390 wr_reg16(info, TCR, value); 1391 spin_unlock_irqrestore(&info->lock,flags); 1392 return 0; 1393 } 1394 1395 #if SYNCLINK_GENERIC_HDLC 1396 1397 /** 1398 * called by generic HDLC layer when protocol selected (PPP, frame relay, etc.) 1399 * set encoding and frame check sequence (FCS) options 1400 * 1401 * dev pointer to network device structure 1402 * encoding serial encoding setting 1403 * parity FCS setting 1404 * 1405 * returns 0 if success, otherwise error code 1406 */ 1407 static int hdlcdev_attach(struct net_device *dev, unsigned short encoding, 1408 unsigned short parity) 1409 { 1410 struct slgt_info *info = dev_to_port(dev); 1411 unsigned char new_encoding; 1412 unsigned short new_crctype; 1413 1414 /* return error if TTY interface open */ 1415 if (info->port.count) 1416 return -EBUSY; 1417 1418 DBGINFO(("%s hdlcdev_attach\n", info->device_name)); 1419 1420 switch (encoding) 1421 { 1422 case ENCODING_NRZ: new_encoding = HDLC_ENCODING_NRZ; break; 1423 case ENCODING_NRZI: new_encoding = HDLC_ENCODING_NRZI_SPACE; break; 1424 case ENCODING_FM_MARK: new_encoding = HDLC_ENCODING_BIPHASE_MARK; break; 1425 case ENCODING_FM_SPACE: new_encoding = HDLC_ENCODING_BIPHASE_SPACE; break; 1426 case ENCODING_MANCHESTER: new_encoding = HDLC_ENCODING_BIPHASE_LEVEL; break; 1427 default: return -EINVAL; 1428 } 1429 1430 switch (parity) 1431 { 1432 case PARITY_NONE: new_crctype = HDLC_CRC_NONE; break; 1433 case PARITY_CRC16_PR1_CCITT: new_crctype = HDLC_CRC_16_CCITT; break; 1434 case PARITY_CRC32_PR1_CCITT: new_crctype = HDLC_CRC_32_CCITT; break; 1435 default: return -EINVAL; 1436 } 1437 1438 info->params.encoding = new_encoding; 1439 info->params.crc_type = new_crctype; 1440 1441 /* if network interface up, reprogram hardware */ 1442 if (info->netcount) 1443 program_hw(info); 1444 1445 return 0; 1446 } 1447 1448 /** 1449 * called by generic HDLC layer to send frame 1450 * 1451 * skb socket buffer containing HDLC frame 1452 * dev pointer to network device structure 1453 */ 1454 static netdev_tx_t hdlcdev_xmit(struct sk_buff *skb, 1455 struct net_device *dev) 1456 { 1457 struct slgt_info *info = dev_to_port(dev); 1458 unsigned long flags; 1459 1460 DBGINFO(("%s hdlc_xmit\n", dev->name)); 1461 1462 if (!skb->len) 1463 return NETDEV_TX_OK; 1464 1465 /* stop sending until this frame completes */ 1466 netif_stop_queue(dev); 1467 1468 /* update network statistics */ 1469 dev->stats.tx_packets++; 1470 dev->stats.tx_bytes += skb->len; 1471 1472 /* save start time for transmit timeout detection */ 1473 netif_trans_update(dev); 1474 1475 spin_lock_irqsave(&info->lock, flags); 1476 tx_load(info, skb->data, skb->len); 1477 spin_unlock_irqrestore(&info->lock, flags); 1478 1479 /* done with socket buffer, so free it */ 1480 dev_kfree_skb(skb); 1481 1482 return NETDEV_TX_OK; 1483 } 1484 1485 /** 1486 * called by network layer when interface enabled 1487 * claim resources and initialize hardware 1488 * 1489 * dev pointer to network device structure 1490 * 1491 * returns 0 if success, otherwise error code 1492 */ 1493 static int hdlcdev_open(struct net_device *dev) 1494 { 1495 struct slgt_info *info = dev_to_port(dev); 1496 int rc; 1497 unsigned long flags; 1498 1499 if (!try_module_get(THIS_MODULE)) 1500 return -EBUSY; 1501 1502 DBGINFO(("%s hdlcdev_open\n", dev->name)); 1503 1504 /* generic HDLC layer open processing */ 1505 rc = hdlc_open(dev); 1506 if (rc) 1507 return rc; 1508 1509 /* arbitrate between network and tty opens */ 1510 spin_lock_irqsave(&info->netlock, flags); 1511 if (info->port.count != 0 || info->netcount != 0) { 1512 DBGINFO(("%s hdlc_open busy\n", dev->name)); 1513 spin_unlock_irqrestore(&info->netlock, flags); 1514 return -EBUSY; 1515 } 1516 info->netcount=1; 1517 spin_unlock_irqrestore(&info->netlock, flags); 1518 1519 /* claim resources and init adapter */ 1520 if ((rc = startup(info)) != 0) { 1521 spin_lock_irqsave(&info->netlock, flags); 1522 info->netcount=0; 1523 spin_unlock_irqrestore(&info->netlock, flags); 1524 return rc; 1525 } 1526 1527 /* assert RTS and DTR, apply hardware settings */ 1528 info->signals |= SerialSignal_RTS | SerialSignal_DTR; 1529 program_hw(info); 1530 1531 /* enable network layer transmit */ 1532 netif_trans_update(dev); 1533 netif_start_queue(dev); 1534 1535 /* inform generic HDLC layer of current DCD status */ 1536 spin_lock_irqsave(&info->lock, flags); 1537 get_signals(info); 1538 spin_unlock_irqrestore(&info->lock, flags); 1539 if (info->signals & SerialSignal_DCD) 1540 netif_carrier_on(dev); 1541 else 1542 netif_carrier_off(dev); 1543 return 0; 1544 } 1545 1546 /** 1547 * called by network layer when interface is disabled 1548 * shutdown hardware and release resources 1549 * 1550 * dev pointer to network device structure 1551 * 1552 * returns 0 if success, otherwise error code 1553 */ 1554 static int hdlcdev_close(struct net_device *dev) 1555 { 1556 struct slgt_info *info = dev_to_port(dev); 1557 unsigned long flags; 1558 1559 DBGINFO(("%s hdlcdev_close\n", dev->name)); 1560 1561 netif_stop_queue(dev); 1562 1563 /* shutdown adapter and release resources */ 1564 shutdown(info); 1565 1566 hdlc_close(dev); 1567 1568 spin_lock_irqsave(&info->netlock, flags); 1569 info->netcount=0; 1570 spin_unlock_irqrestore(&info->netlock, flags); 1571 1572 module_put(THIS_MODULE); 1573 return 0; 1574 } 1575 1576 /** 1577 * called by network layer to process IOCTL call to network device 1578 * 1579 * dev pointer to network device structure 1580 * ifr pointer to network interface request structure 1581 * cmd IOCTL command code 1582 * 1583 * returns 0 if success, otherwise error code 1584 */ 1585 static int hdlcdev_ioctl(struct net_device *dev, struct ifreq *ifr, int cmd) 1586 { 1587 const size_t size = sizeof(sync_serial_settings); 1588 sync_serial_settings new_line; 1589 sync_serial_settings __user *line = ifr->ifr_settings.ifs_ifsu.sync; 1590 struct slgt_info *info = dev_to_port(dev); 1591 unsigned int flags; 1592 1593 DBGINFO(("%s hdlcdev_ioctl\n", dev->name)); 1594 1595 /* return error if TTY interface open */ 1596 if (info->port.count) 1597 return -EBUSY; 1598 1599 if (cmd != SIOCWANDEV) 1600 return hdlc_ioctl(dev, ifr, cmd); 1601 1602 memset(&new_line, 0, sizeof(new_line)); 1603 1604 switch(ifr->ifr_settings.type) { 1605 case IF_GET_IFACE: /* return current sync_serial_settings */ 1606 1607 ifr->ifr_settings.type = IF_IFACE_SYNC_SERIAL; 1608 if (ifr->ifr_settings.size < size) { 1609 ifr->ifr_settings.size = size; /* data size wanted */ 1610 return -ENOBUFS; 1611 } 1612 1613 flags = info->params.flags & (HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_RXC_DPLL | 1614 HDLC_FLAG_RXC_BRG | HDLC_FLAG_RXC_TXCPIN | 1615 HDLC_FLAG_TXC_TXCPIN | HDLC_FLAG_TXC_DPLL | 1616 HDLC_FLAG_TXC_BRG | HDLC_FLAG_TXC_RXCPIN); 1617 1618 switch (flags){ 1619 case (HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_TXCPIN): new_line.clock_type = CLOCK_EXT; break; 1620 case (HDLC_FLAG_RXC_BRG | HDLC_FLAG_TXC_BRG): new_line.clock_type = CLOCK_INT; break; 1621 case (HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_BRG): new_line.clock_type = CLOCK_TXINT; break; 1622 case (HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_RXCPIN): new_line.clock_type = CLOCK_TXFROMRX; break; 1623 default: new_line.clock_type = CLOCK_DEFAULT; 1624 } 1625 1626 new_line.clock_rate = info->params.clock_speed; 1627 new_line.loopback = info->params.loopback ? 1:0; 1628 1629 if (copy_to_user(line, &new_line, size)) 1630 return -EFAULT; 1631 return 0; 1632 1633 case IF_IFACE_SYNC_SERIAL: /* set sync_serial_settings */ 1634 1635 if(!capable(CAP_NET_ADMIN)) 1636 return -EPERM; 1637 if (copy_from_user(&new_line, line, size)) 1638 return -EFAULT; 1639 1640 switch (new_line.clock_type) 1641 { 1642 case CLOCK_EXT: flags = HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_TXCPIN; break; 1643 case CLOCK_TXFROMRX: flags = HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_RXCPIN; break; 1644 case CLOCK_INT: flags = HDLC_FLAG_RXC_BRG | HDLC_FLAG_TXC_BRG; break; 1645 case CLOCK_TXINT: flags = HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_BRG; break; 1646 case CLOCK_DEFAULT: flags = info->params.flags & 1647 (HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_RXC_DPLL | 1648 HDLC_FLAG_RXC_BRG | HDLC_FLAG_RXC_TXCPIN | 1649 HDLC_FLAG_TXC_TXCPIN | HDLC_FLAG_TXC_DPLL | 1650 HDLC_FLAG_TXC_BRG | HDLC_FLAG_TXC_RXCPIN); break; 1651 default: return -EINVAL; 1652 } 1653 1654 if (new_line.loopback != 0 && new_line.loopback != 1) 1655 return -EINVAL; 1656 1657 info->params.flags &= ~(HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_RXC_DPLL | 1658 HDLC_FLAG_RXC_BRG | HDLC_FLAG_RXC_TXCPIN | 1659 HDLC_FLAG_TXC_TXCPIN | HDLC_FLAG_TXC_DPLL | 1660 HDLC_FLAG_TXC_BRG | HDLC_FLAG_TXC_RXCPIN); 1661 info->params.flags |= flags; 1662 1663 info->params.loopback = new_line.loopback; 1664 1665 if (flags & (HDLC_FLAG_RXC_BRG | HDLC_FLAG_TXC_BRG)) 1666 info->params.clock_speed = new_line.clock_rate; 1667 else 1668 info->params.clock_speed = 0; 1669 1670 /* if network interface up, reprogram hardware */ 1671 if (info->netcount) 1672 program_hw(info); 1673 return 0; 1674 1675 default: 1676 return hdlc_ioctl(dev, ifr, cmd); 1677 } 1678 } 1679 1680 /** 1681 * called by network layer when transmit timeout is detected 1682 * 1683 * dev pointer to network device structure 1684 */ 1685 static void hdlcdev_tx_timeout(struct net_device *dev) 1686 { 1687 struct slgt_info *info = dev_to_port(dev); 1688 unsigned long flags; 1689 1690 DBGINFO(("%s hdlcdev_tx_timeout\n", dev->name)); 1691 1692 dev->stats.tx_errors++; 1693 dev->stats.tx_aborted_errors++; 1694 1695 spin_lock_irqsave(&info->lock,flags); 1696 tx_stop(info); 1697 spin_unlock_irqrestore(&info->lock,flags); 1698 1699 netif_wake_queue(dev); 1700 } 1701 1702 /** 1703 * called by device driver when transmit completes 1704 * reenable network layer transmit if stopped 1705 * 1706 * info pointer to device instance information 1707 */ 1708 static void hdlcdev_tx_done(struct slgt_info *info) 1709 { 1710 if (netif_queue_stopped(info->netdev)) 1711 netif_wake_queue(info->netdev); 1712 } 1713 1714 /** 1715 * called by device driver when frame received 1716 * pass frame to network layer 1717 * 1718 * info pointer to device instance information 1719 * buf pointer to buffer contianing frame data 1720 * size count of data bytes in buf 1721 */ 1722 static void hdlcdev_rx(struct slgt_info *info, char *buf, int size) 1723 { 1724 struct sk_buff *skb = dev_alloc_skb(size); 1725 struct net_device *dev = info->netdev; 1726 1727 DBGINFO(("%s hdlcdev_rx\n", dev->name)); 1728 1729 if (skb == NULL) { 1730 DBGERR(("%s: can't alloc skb, drop packet\n", dev->name)); 1731 dev->stats.rx_dropped++; 1732 return; 1733 } 1734 1735 skb_put_data(skb, buf, size); 1736 1737 skb->protocol = hdlc_type_trans(skb, dev); 1738 1739 dev->stats.rx_packets++; 1740 dev->stats.rx_bytes += size; 1741 1742 netif_rx(skb); 1743 } 1744 1745 static const struct net_device_ops hdlcdev_ops = { 1746 .ndo_open = hdlcdev_open, 1747 .ndo_stop = hdlcdev_close, 1748 .ndo_start_xmit = hdlc_start_xmit, 1749 .ndo_do_ioctl = hdlcdev_ioctl, 1750 .ndo_tx_timeout = hdlcdev_tx_timeout, 1751 }; 1752 1753 /** 1754 * called by device driver when adding device instance 1755 * do generic HDLC initialization 1756 * 1757 * info pointer to device instance information 1758 * 1759 * returns 0 if success, otherwise error code 1760 */ 1761 static int hdlcdev_init(struct slgt_info *info) 1762 { 1763 int rc; 1764 struct net_device *dev; 1765 hdlc_device *hdlc; 1766 1767 /* allocate and initialize network and HDLC layer objects */ 1768 1769 dev = alloc_hdlcdev(info); 1770 if (!dev) { 1771 printk(KERN_ERR "%s hdlc device alloc failure\n", info->device_name); 1772 return -ENOMEM; 1773 } 1774 1775 /* for network layer reporting purposes only */ 1776 dev->mem_start = info->phys_reg_addr; 1777 dev->mem_end = info->phys_reg_addr + SLGT_REG_SIZE - 1; 1778 dev->irq = info->irq_level; 1779 1780 /* network layer callbacks and settings */ 1781 dev->netdev_ops = &hdlcdev_ops; 1782 dev->watchdog_timeo = 10 * HZ; 1783 dev->tx_queue_len = 50; 1784 1785 /* generic HDLC layer callbacks and settings */ 1786 hdlc = dev_to_hdlc(dev); 1787 hdlc->attach = hdlcdev_attach; 1788 hdlc->xmit = hdlcdev_xmit; 1789 1790 /* register objects with HDLC layer */ 1791 rc = register_hdlc_device(dev); 1792 if (rc) { 1793 printk(KERN_WARNING "%s:unable to register hdlc device\n",__FILE__); 1794 free_netdev(dev); 1795 return rc; 1796 } 1797 1798 info->netdev = dev; 1799 return 0; 1800 } 1801 1802 /** 1803 * called by device driver when removing device instance 1804 * do generic HDLC cleanup 1805 * 1806 * info pointer to device instance information 1807 */ 1808 static void hdlcdev_exit(struct slgt_info *info) 1809 { 1810 unregister_hdlc_device(info->netdev); 1811 free_netdev(info->netdev); 1812 info->netdev = NULL; 1813 } 1814 1815 #endif /* ifdef CONFIG_HDLC */ 1816 1817 /* 1818 * get async data from rx DMA buffers 1819 */ 1820 static void rx_async(struct slgt_info *info) 1821 { 1822 struct mgsl_icount *icount = &info->icount; 1823 unsigned int start, end; 1824 unsigned char *p; 1825 unsigned char status; 1826 struct slgt_desc *bufs = info->rbufs; 1827 int i, count; 1828 int chars = 0; 1829 int stat; 1830 unsigned char ch; 1831 1832 start = end = info->rbuf_current; 1833 1834 while(desc_complete(bufs[end])) { 1835 count = desc_count(bufs[end]) - info->rbuf_index; 1836 p = bufs[end].buf + info->rbuf_index; 1837 1838 DBGISR(("%s rx_async count=%d\n", info->device_name, count)); 1839 DBGDATA(info, p, count, "rx"); 1840 1841 for(i=0 ; i < count; i+=2, p+=2) { 1842 ch = *p; 1843 icount->rx++; 1844 1845 stat = 0; 1846 1847 status = *(p + 1) & (BIT1 + BIT0); 1848 if (status) { 1849 if (status & BIT1) 1850 icount->parity++; 1851 else if (status & BIT0) 1852 icount->frame++; 1853 /* discard char if tty control flags say so */ 1854 if (status & info->ignore_status_mask) 1855 continue; 1856 if (status & BIT1) 1857 stat = TTY_PARITY; 1858 else if (status & BIT0) 1859 stat = TTY_FRAME; 1860 } 1861 tty_insert_flip_char(&info->port, ch, stat); 1862 chars++; 1863 } 1864 1865 if (i < count) { 1866 /* receive buffer not completed */ 1867 info->rbuf_index += i; 1868 mod_timer(&info->rx_timer, jiffies + 1); 1869 break; 1870 } 1871 1872 info->rbuf_index = 0; 1873 free_rbufs(info, end, end); 1874 1875 if (++end == info->rbuf_count) 1876 end = 0; 1877 1878 /* if entire list searched then no frame available */ 1879 if (end == start) 1880 break; 1881 } 1882 1883 if (chars) 1884 tty_flip_buffer_push(&info->port); 1885 } 1886 1887 /* 1888 * return next bottom half action to perform 1889 */ 1890 static int bh_action(struct slgt_info *info) 1891 { 1892 unsigned long flags; 1893 int rc; 1894 1895 spin_lock_irqsave(&info->lock,flags); 1896 1897 if (info->pending_bh & BH_RECEIVE) { 1898 info->pending_bh &= ~BH_RECEIVE; 1899 rc = BH_RECEIVE; 1900 } else if (info->pending_bh & BH_TRANSMIT) { 1901 info->pending_bh &= ~BH_TRANSMIT; 1902 rc = BH_TRANSMIT; 1903 } else if (info->pending_bh & BH_STATUS) { 1904 info->pending_bh &= ~BH_STATUS; 1905 rc = BH_STATUS; 1906 } else { 1907 /* Mark BH routine as complete */ 1908 info->bh_running = false; 1909 info->bh_requested = false; 1910 rc = 0; 1911 } 1912 1913 spin_unlock_irqrestore(&info->lock,flags); 1914 1915 return rc; 1916 } 1917 1918 /* 1919 * perform bottom half processing 1920 */ 1921 static void bh_handler(struct work_struct *work) 1922 { 1923 struct slgt_info *info = container_of(work, struct slgt_info, task); 1924 int action; 1925 1926 info->bh_running = true; 1927 1928 while((action = bh_action(info))) { 1929 switch (action) { 1930 case BH_RECEIVE: 1931 DBGBH(("%s bh receive\n", info->device_name)); 1932 switch(info->params.mode) { 1933 case MGSL_MODE_ASYNC: 1934 rx_async(info); 1935 break; 1936 case MGSL_MODE_HDLC: 1937 while(rx_get_frame(info)); 1938 break; 1939 case MGSL_MODE_RAW: 1940 case MGSL_MODE_MONOSYNC: 1941 case MGSL_MODE_BISYNC: 1942 case MGSL_MODE_XSYNC: 1943 while(rx_get_buf(info)); 1944 break; 1945 } 1946 /* restart receiver if rx DMA buffers exhausted */ 1947 if (info->rx_restart) 1948 rx_start(info); 1949 break; 1950 case BH_TRANSMIT: 1951 bh_transmit(info); 1952 break; 1953 case BH_STATUS: 1954 DBGBH(("%s bh status\n", info->device_name)); 1955 info->ri_chkcount = 0; 1956 info->dsr_chkcount = 0; 1957 info->dcd_chkcount = 0; 1958 info->cts_chkcount = 0; 1959 break; 1960 default: 1961 DBGBH(("%s unknown action\n", info->device_name)); 1962 break; 1963 } 1964 } 1965 DBGBH(("%s bh_handler exit\n", info->device_name)); 1966 } 1967 1968 static void bh_transmit(struct slgt_info *info) 1969 { 1970 struct tty_struct *tty = info->port.tty; 1971 1972 DBGBH(("%s bh_transmit\n", info->device_name)); 1973 if (tty) 1974 tty_wakeup(tty); 1975 } 1976 1977 static void dsr_change(struct slgt_info *info, unsigned short status) 1978 { 1979 if (status & BIT3) { 1980 info->signals |= SerialSignal_DSR; 1981 info->input_signal_events.dsr_up++; 1982 } else { 1983 info->signals &= ~SerialSignal_DSR; 1984 info->input_signal_events.dsr_down++; 1985 } 1986 DBGISR(("dsr_change %s signals=%04X\n", info->device_name, info->signals)); 1987 if ((info->dsr_chkcount)++ == IO_PIN_SHUTDOWN_LIMIT) { 1988 slgt_irq_off(info, IRQ_DSR); 1989 return; 1990 } 1991 info->icount.dsr++; 1992 wake_up_interruptible(&info->status_event_wait_q); 1993 wake_up_interruptible(&info->event_wait_q); 1994 info->pending_bh |= BH_STATUS; 1995 } 1996 1997 static void cts_change(struct slgt_info *info, unsigned short status) 1998 { 1999 if (status & BIT2) { 2000 info->signals |= SerialSignal_CTS; 2001 info->input_signal_events.cts_up++; 2002 } else { 2003 info->signals &= ~SerialSignal_CTS; 2004 info->input_signal_events.cts_down++; 2005 } 2006 DBGISR(("cts_change %s signals=%04X\n", info->device_name, info->signals)); 2007 if ((info->cts_chkcount)++ == IO_PIN_SHUTDOWN_LIMIT) { 2008 slgt_irq_off(info, IRQ_CTS); 2009 return; 2010 } 2011 info->icount.cts++; 2012 wake_up_interruptible(&info->status_event_wait_q); 2013 wake_up_interruptible(&info->event_wait_q); 2014 info->pending_bh |= BH_STATUS; 2015 2016 if (tty_port_cts_enabled(&info->port)) { 2017 if (info->port.tty) { 2018 if (info->port.tty->hw_stopped) { 2019 if (info->signals & SerialSignal_CTS) { 2020 info->port.tty->hw_stopped = 0; 2021 info->pending_bh |= BH_TRANSMIT; 2022 return; 2023 } 2024 } else { 2025 if (!(info->signals & SerialSignal_CTS)) 2026 info->port.tty->hw_stopped = 1; 2027 } 2028 } 2029 } 2030 } 2031 2032 static void dcd_change(struct slgt_info *info, unsigned short status) 2033 { 2034 if (status & BIT1) { 2035 info->signals |= SerialSignal_DCD; 2036 info->input_signal_events.dcd_up++; 2037 } else { 2038 info->signals &= ~SerialSignal_DCD; 2039 info->input_signal_events.dcd_down++; 2040 } 2041 DBGISR(("dcd_change %s signals=%04X\n", info->device_name, info->signals)); 2042 if ((info->dcd_chkcount)++ == IO_PIN_SHUTDOWN_LIMIT) { 2043 slgt_irq_off(info, IRQ_DCD); 2044 return; 2045 } 2046 info->icount.dcd++; 2047 #if SYNCLINK_GENERIC_HDLC 2048 if (info->netcount) { 2049 if (info->signals & SerialSignal_DCD) 2050 netif_carrier_on(info->netdev); 2051 else 2052 netif_carrier_off(info->netdev); 2053 } 2054 #endif 2055 wake_up_interruptible(&info->status_event_wait_q); 2056 wake_up_interruptible(&info->event_wait_q); 2057 info->pending_bh |= BH_STATUS; 2058 2059 if (tty_port_check_carrier(&info->port)) { 2060 if (info->signals & SerialSignal_DCD) 2061 wake_up_interruptible(&info->port.open_wait); 2062 else { 2063 if (info->port.tty) 2064 tty_hangup(info->port.tty); 2065 } 2066 } 2067 } 2068 2069 static void ri_change(struct slgt_info *info, unsigned short status) 2070 { 2071 if (status & BIT0) { 2072 info->signals |= SerialSignal_RI; 2073 info->input_signal_events.ri_up++; 2074 } else { 2075 info->signals &= ~SerialSignal_RI; 2076 info->input_signal_events.ri_down++; 2077 } 2078 DBGISR(("ri_change %s signals=%04X\n", info->device_name, info->signals)); 2079 if ((info->ri_chkcount)++ == IO_PIN_SHUTDOWN_LIMIT) { 2080 slgt_irq_off(info, IRQ_RI); 2081 return; 2082 } 2083 info->icount.rng++; 2084 wake_up_interruptible(&info->status_event_wait_q); 2085 wake_up_interruptible(&info->event_wait_q); 2086 info->pending_bh |= BH_STATUS; 2087 } 2088 2089 static void isr_rxdata(struct slgt_info *info) 2090 { 2091 unsigned int count = info->rbuf_fill_count; 2092 unsigned int i = info->rbuf_fill_index; 2093 unsigned short reg; 2094 2095 while (rd_reg16(info, SSR) & IRQ_RXDATA) { 2096 reg = rd_reg16(info, RDR); 2097 DBGISR(("isr_rxdata %s RDR=%04X\n", info->device_name, reg)); 2098 if (desc_complete(info->rbufs[i])) { 2099 /* all buffers full */ 2100 rx_stop(info); 2101 info->rx_restart = 1; 2102 continue; 2103 } 2104 info->rbufs[i].buf[count++] = (unsigned char)reg; 2105 /* async mode saves status byte to buffer for each data byte */ 2106 if (info->params.mode == MGSL_MODE_ASYNC) 2107 info->rbufs[i].buf[count++] = (unsigned char)(reg >> 8); 2108 if (count == info->rbuf_fill_level || (reg & BIT10)) { 2109 /* buffer full or end of frame */ 2110 set_desc_count(info->rbufs[i], count); 2111 set_desc_status(info->rbufs[i], BIT15 | (reg >> 8)); 2112 info->rbuf_fill_count = count = 0; 2113 if (++i == info->rbuf_count) 2114 i = 0; 2115 info->pending_bh |= BH_RECEIVE; 2116 } 2117 } 2118 2119 info->rbuf_fill_index = i; 2120 info->rbuf_fill_count = count; 2121 } 2122 2123 static void isr_serial(struct slgt_info *info) 2124 { 2125 unsigned short status = rd_reg16(info, SSR); 2126 2127 DBGISR(("%s isr_serial status=%04X\n", info->device_name, status)); 2128 2129 wr_reg16(info, SSR, status); /* clear pending */ 2130 2131 info->irq_occurred = true; 2132 2133 if (info->params.mode == MGSL_MODE_ASYNC) { 2134 if (status & IRQ_TXIDLE) { 2135 if (info->tx_active) 2136 isr_txeom(info, status); 2137 } 2138 if (info->rx_pio && (status & IRQ_RXDATA)) 2139 isr_rxdata(info); 2140 if ((status & IRQ_RXBREAK) && (status & RXBREAK)) { 2141 info->icount.brk++; 2142 /* process break detection if tty control allows */ 2143 if (info->port.tty) { 2144 if (!(status & info->ignore_status_mask)) { 2145 if (info->read_status_mask & MASK_BREAK) { 2146 tty_insert_flip_char(&info->port, 0, TTY_BREAK); 2147 if (info->port.flags & ASYNC_SAK) 2148 do_SAK(info->port.tty); 2149 } 2150 } 2151 } 2152 } 2153 } else { 2154 if (status & (IRQ_TXIDLE + IRQ_TXUNDER)) 2155 isr_txeom(info, status); 2156 if (info->rx_pio && (status & IRQ_RXDATA)) 2157 isr_rxdata(info); 2158 if (status & IRQ_RXIDLE) { 2159 if (status & RXIDLE) 2160 info->icount.rxidle++; 2161 else 2162 info->icount.exithunt++; 2163 wake_up_interruptible(&info->event_wait_q); 2164 } 2165 2166 if (status & IRQ_RXOVER) 2167 rx_start(info); 2168 } 2169 2170 if (status & IRQ_DSR) 2171 dsr_change(info, status); 2172 if (status & IRQ_CTS) 2173 cts_change(info, status); 2174 if (status & IRQ_DCD) 2175 dcd_change(info, status); 2176 if (status & IRQ_RI) 2177 ri_change(info, status); 2178 } 2179 2180 static void isr_rdma(struct slgt_info *info) 2181 { 2182 unsigned int status = rd_reg32(info, RDCSR); 2183 2184 DBGISR(("%s isr_rdma status=%08x\n", info->device_name, status)); 2185 2186 /* RDCSR (rx DMA control/status) 2187 * 2188 * 31..07 reserved 2189 * 06 save status byte to DMA buffer 2190 * 05 error 2191 * 04 eol (end of list) 2192 * 03 eob (end of buffer) 2193 * 02 IRQ enable 2194 * 01 reset 2195 * 00 enable 2196 */ 2197 wr_reg32(info, RDCSR, status); /* clear pending */ 2198 2199 if (status & (BIT5 + BIT4)) { 2200 DBGISR(("%s isr_rdma rx_restart=1\n", info->device_name)); 2201 info->rx_restart = true; 2202 } 2203 info->pending_bh |= BH_RECEIVE; 2204 } 2205 2206 static void isr_tdma(struct slgt_info *info) 2207 { 2208 unsigned int status = rd_reg32(info, TDCSR); 2209 2210 DBGISR(("%s isr_tdma status=%08x\n", info->device_name, status)); 2211 2212 /* TDCSR (tx DMA control/status) 2213 * 2214 * 31..06 reserved 2215 * 05 error 2216 * 04 eol (end of list) 2217 * 03 eob (end of buffer) 2218 * 02 IRQ enable 2219 * 01 reset 2220 * 00 enable 2221 */ 2222 wr_reg32(info, TDCSR, status); /* clear pending */ 2223 2224 if (status & (BIT5 + BIT4 + BIT3)) { 2225 // another transmit buffer has completed 2226 // run bottom half to get more send data from user 2227 info->pending_bh |= BH_TRANSMIT; 2228 } 2229 } 2230 2231 /* 2232 * return true if there are unsent tx DMA buffers, otherwise false 2233 * 2234 * if there are unsent buffers then info->tbuf_start 2235 * is set to index of first unsent buffer 2236 */ 2237 static bool unsent_tbufs(struct slgt_info *info) 2238 { 2239 unsigned int i = info->tbuf_current; 2240 bool rc = false; 2241 2242 /* 2243 * search backwards from last loaded buffer (precedes tbuf_current) 2244 * for first unsent buffer (desc_count > 0) 2245 */ 2246 2247 do { 2248 if (i) 2249 i--; 2250 else 2251 i = info->tbuf_count - 1; 2252 if (!desc_count(info->tbufs[i])) 2253 break; 2254 info->tbuf_start = i; 2255 rc = true; 2256 } while (i != info->tbuf_current); 2257 2258 return rc; 2259 } 2260 2261 static void isr_txeom(struct slgt_info *info, unsigned short status) 2262 { 2263 DBGISR(("%s txeom status=%04x\n", info->device_name, status)); 2264 2265 slgt_irq_off(info, IRQ_TXDATA + IRQ_TXIDLE + IRQ_TXUNDER); 2266 tdma_reset(info); 2267 if (status & IRQ_TXUNDER) { 2268 unsigned short val = rd_reg16(info, TCR); 2269 wr_reg16(info, TCR, (unsigned short)(val | BIT2)); /* set reset bit */ 2270 wr_reg16(info, TCR, val); /* clear reset bit */ 2271 } 2272 2273 if (info->tx_active) { 2274 if (info->params.mode != MGSL_MODE_ASYNC) { 2275 if (status & IRQ_TXUNDER) 2276 info->icount.txunder++; 2277 else if (status & IRQ_TXIDLE) 2278 info->icount.txok++; 2279 } 2280 2281 if (unsent_tbufs(info)) { 2282 tx_start(info); 2283 update_tx_timer(info); 2284 return; 2285 } 2286 info->tx_active = false; 2287 2288 del_timer(&info->tx_timer); 2289 2290 if (info->params.mode != MGSL_MODE_ASYNC && info->drop_rts_on_tx_done) { 2291 info->signals &= ~SerialSignal_RTS; 2292 info->drop_rts_on_tx_done = false; 2293 set_signals(info); 2294 } 2295 2296 #if SYNCLINK_GENERIC_HDLC 2297 if (info->netcount) 2298 hdlcdev_tx_done(info); 2299 else 2300 #endif 2301 { 2302 if (info->port.tty && (info->port.tty->stopped || info->port.tty->hw_stopped)) { 2303 tx_stop(info); 2304 return; 2305 } 2306 info->pending_bh |= BH_TRANSMIT; 2307 } 2308 } 2309 } 2310 2311 static void isr_gpio(struct slgt_info *info, unsigned int changed, unsigned int state) 2312 { 2313 struct cond_wait *w, *prev; 2314 2315 /* wake processes waiting for specific transitions */ 2316 for (w = info->gpio_wait_q, prev = NULL ; w != NULL ; w = w->next) { 2317 if (w->data & changed) { 2318 w->data = state; 2319 wake_up_interruptible(&w->q); 2320 if (prev != NULL) 2321 prev->next = w->next; 2322 else 2323 info->gpio_wait_q = w->next; 2324 } else 2325 prev = w; 2326 } 2327 } 2328 2329 /* interrupt service routine 2330 * 2331 * irq interrupt number 2332 * dev_id device ID supplied during interrupt registration 2333 */ 2334 static irqreturn_t slgt_interrupt(int dummy, void *dev_id) 2335 { 2336 struct slgt_info *info = dev_id; 2337 unsigned int gsr; 2338 unsigned int i; 2339 2340 DBGISR(("slgt_interrupt irq=%d entry\n", info->irq_level)); 2341 2342 while((gsr = rd_reg32(info, GSR) & 0xffffff00)) { 2343 DBGISR(("%s gsr=%08x\n", info->device_name, gsr)); 2344 info->irq_occurred = true; 2345 for(i=0; i < info->port_count ; i++) { 2346 if (info->port_array[i] == NULL) 2347 continue; 2348 spin_lock(&info->port_array[i]->lock); 2349 if (gsr & (BIT8 << i)) 2350 isr_serial(info->port_array[i]); 2351 if (gsr & (BIT16 << (i*2))) 2352 isr_rdma(info->port_array[i]); 2353 if (gsr & (BIT17 << (i*2))) 2354 isr_tdma(info->port_array[i]); 2355 spin_unlock(&info->port_array[i]->lock); 2356 } 2357 } 2358 2359 if (info->gpio_present) { 2360 unsigned int state; 2361 unsigned int changed; 2362 spin_lock(&info->lock); 2363 while ((changed = rd_reg32(info, IOSR)) != 0) { 2364 DBGISR(("%s iosr=%08x\n", info->device_name, changed)); 2365 /* read latched state of GPIO signals */ 2366 state = rd_reg32(info, IOVR); 2367 /* clear pending GPIO interrupt bits */ 2368 wr_reg32(info, IOSR, changed); 2369 for (i=0 ; i < info->port_count ; i++) { 2370 if (info->port_array[i] != NULL) 2371 isr_gpio(info->port_array[i], changed, state); 2372 } 2373 } 2374 spin_unlock(&info->lock); 2375 } 2376 2377 for(i=0; i < info->port_count ; i++) { 2378 struct slgt_info *port = info->port_array[i]; 2379 if (port == NULL) 2380 continue; 2381 spin_lock(&port->lock); 2382 if ((port->port.count || port->netcount) && 2383 port->pending_bh && !port->bh_running && 2384 !port->bh_requested) { 2385 DBGISR(("%s bh queued\n", port->device_name)); 2386 schedule_work(&port->task); 2387 port->bh_requested = true; 2388 } 2389 spin_unlock(&port->lock); 2390 } 2391 2392 DBGISR(("slgt_interrupt irq=%d exit\n", info->irq_level)); 2393 return IRQ_HANDLED; 2394 } 2395 2396 static int startup(struct slgt_info *info) 2397 { 2398 DBGINFO(("%s startup\n", info->device_name)); 2399 2400 if (tty_port_initialized(&info->port)) 2401 return 0; 2402 2403 if (!info->tx_buf) { 2404 info->tx_buf = kmalloc(info->max_frame_size, GFP_KERNEL); 2405 if (!info->tx_buf) { 2406 DBGERR(("%s can't allocate tx buffer\n", info->device_name)); 2407 return -ENOMEM; 2408 } 2409 } 2410 2411 info->pending_bh = 0; 2412 2413 memset(&info->icount, 0, sizeof(info->icount)); 2414 2415 /* program hardware for current parameters */ 2416 change_params(info); 2417 2418 if (info->port.tty) 2419 clear_bit(TTY_IO_ERROR, &info->port.tty->flags); 2420 2421 tty_port_set_initialized(&info->port, 1); 2422 2423 return 0; 2424 } 2425 2426 /* 2427 * called by close() and hangup() to shutdown hardware 2428 */ 2429 static void shutdown(struct slgt_info *info) 2430 { 2431 unsigned long flags; 2432 2433 if (!tty_port_initialized(&info->port)) 2434 return; 2435 2436 DBGINFO(("%s shutdown\n", info->device_name)); 2437 2438 /* clear status wait queue because status changes */ 2439 /* can't happen after shutting down the hardware */ 2440 wake_up_interruptible(&info->status_event_wait_q); 2441 wake_up_interruptible(&info->event_wait_q); 2442 2443 del_timer_sync(&info->tx_timer); 2444 del_timer_sync(&info->rx_timer); 2445 2446 kfree(info->tx_buf); 2447 info->tx_buf = NULL; 2448 2449 spin_lock_irqsave(&info->lock,flags); 2450 2451 tx_stop(info); 2452 rx_stop(info); 2453 2454 slgt_irq_off(info, IRQ_ALL | IRQ_MASTER); 2455 2456 if (!info->port.tty || info->port.tty->termios.c_cflag & HUPCL) { 2457 info->signals &= ~(SerialSignal_RTS | SerialSignal_DTR); 2458 set_signals(info); 2459 } 2460 2461 flush_cond_wait(&info->gpio_wait_q); 2462 2463 spin_unlock_irqrestore(&info->lock,flags); 2464 2465 if (info->port.tty) 2466 set_bit(TTY_IO_ERROR, &info->port.tty->flags); 2467 2468 tty_port_set_initialized(&info->port, 0); 2469 } 2470 2471 static void program_hw(struct slgt_info *info) 2472 { 2473 unsigned long flags; 2474 2475 spin_lock_irqsave(&info->lock,flags); 2476 2477 rx_stop(info); 2478 tx_stop(info); 2479 2480 if (info->params.mode != MGSL_MODE_ASYNC || 2481 info->netcount) 2482 sync_mode(info); 2483 else 2484 async_mode(info); 2485 2486 set_signals(info); 2487 2488 info->dcd_chkcount = 0; 2489 info->cts_chkcount = 0; 2490 info->ri_chkcount = 0; 2491 info->dsr_chkcount = 0; 2492 2493 slgt_irq_on(info, IRQ_DCD | IRQ_CTS | IRQ_DSR | IRQ_RI); 2494 get_signals(info); 2495 2496 if (info->netcount || 2497 (info->port.tty && info->port.tty->termios.c_cflag & CREAD)) 2498 rx_start(info); 2499 2500 spin_unlock_irqrestore(&info->lock,flags); 2501 } 2502 2503 /* 2504 * reconfigure adapter based on new parameters 2505 */ 2506 static void change_params(struct slgt_info *info) 2507 { 2508 unsigned cflag; 2509 int bits_per_char; 2510 2511 if (!info->port.tty) 2512 return; 2513 DBGINFO(("%s change_params\n", info->device_name)); 2514 2515 cflag = info->port.tty->termios.c_cflag; 2516 2517 /* if B0 rate (hangup) specified then negate RTS and DTR */ 2518 /* otherwise assert RTS and DTR */ 2519 if (cflag & CBAUD) 2520 info->signals |= SerialSignal_RTS | SerialSignal_DTR; 2521 else 2522 info->signals &= ~(SerialSignal_RTS | SerialSignal_DTR); 2523 2524 /* byte size and parity */ 2525 2526 switch (cflag & CSIZE) { 2527 case CS5: info->params.data_bits = 5; break; 2528 case CS6: info->params.data_bits = 6; break; 2529 case CS7: info->params.data_bits = 7; break; 2530 case CS8: info->params.data_bits = 8; break; 2531 default: info->params.data_bits = 7; break; 2532 } 2533 2534 info->params.stop_bits = (cflag & CSTOPB) ? 2 : 1; 2535 2536 if (cflag & PARENB) 2537 info->params.parity = (cflag & PARODD) ? ASYNC_PARITY_ODD : ASYNC_PARITY_EVEN; 2538 else 2539 info->params.parity = ASYNC_PARITY_NONE; 2540 2541 /* calculate number of jiffies to transmit a full 2542 * FIFO (32 bytes) at specified data rate 2543 */ 2544 bits_per_char = info->params.data_bits + 2545 info->params.stop_bits + 1; 2546 2547 info->params.data_rate = tty_get_baud_rate(info->port.tty); 2548 2549 if (info->params.data_rate) { 2550 info->timeout = (32*HZ*bits_per_char) / 2551 info->params.data_rate; 2552 } 2553 info->timeout += HZ/50; /* Add .02 seconds of slop */ 2554 2555 tty_port_set_cts_flow(&info->port, cflag & CRTSCTS); 2556 tty_port_set_check_carrier(&info->port, ~cflag & CLOCAL); 2557 2558 /* process tty input control flags */ 2559 2560 info->read_status_mask = IRQ_RXOVER; 2561 if (I_INPCK(info->port.tty)) 2562 info->read_status_mask |= MASK_PARITY | MASK_FRAMING; 2563 if (I_BRKINT(info->port.tty) || I_PARMRK(info->port.tty)) 2564 info->read_status_mask |= MASK_BREAK; 2565 if (I_IGNPAR(info->port.tty)) 2566 info->ignore_status_mask |= MASK_PARITY | MASK_FRAMING; 2567 if (I_IGNBRK(info->port.tty)) { 2568 info->ignore_status_mask |= MASK_BREAK; 2569 /* If ignoring parity and break indicators, ignore 2570 * overruns too. (For real raw support). 2571 */ 2572 if (I_IGNPAR(info->port.tty)) 2573 info->ignore_status_mask |= MASK_OVERRUN; 2574 } 2575 2576 program_hw(info); 2577 } 2578 2579 static int get_stats(struct slgt_info *info, struct mgsl_icount __user *user_icount) 2580 { 2581 DBGINFO(("%s get_stats\n", info->device_name)); 2582 if (!user_icount) { 2583 memset(&info->icount, 0, sizeof(info->icount)); 2584 } else { 2585 if (copy_to_user(user_icount, &info->icount, sizeof(struct mgsl_icount))) 2586 return -EFAULT; 2587 } 2588 return 0; 2589 } 2590 2591 static int get_params(struct slgt_info *info, MGSL_PARAMS __user *user_params) 2592 { 2593 DBGINFO(("%s get_params\n", info->device_name)); 2594 if (copy_to_user(user_params, &info->params, sizeof(MGSL_PARAMS))) 2595 return -EFAULT; 2596 return 0; 2597 } 2598 2599 static int set_params(struct slgt_info *info, MGSL_PARAMS __user *new_params) 2600 { 2601 unsigned long flags; 2602 MGSL_PARAMS tmp_params; 2603 2604 DBGINFO(("%s set_params\n", info->device_name)); 2605 if (copy_from_user(&tmp_params, new_params, sizeof(MGSL_PARAMS))) 2606 return -EFAULT; 2607 2608 spin_lock_irqsave(&info->lock, flags); 2609 if (tmp_params.mode == MGSL_MODE_BASE_CLOCK) 2610 info->base_clock = tmp_params.clock_speed; 2611 else 2612 memcpy(&info->params, &tmp_params, sizeof(MGSL_PARAMS)); 2613 spin_unlock_irqrestore(&info->lock, flags); 2614 2615 program_hw(info); 2616 2617 return 0; 2618 } 2619 2620 static int get_txidle(struct slgt_info *info, int __user *idle_mode) 2621 { 2622 DBGINFO(("%s get_txidle=%d\n", info->device_name, info->idle_mode)); 2623 if (put_user(info->idle_mode, idle_mode)) 2624 return -EFAULT; 2625 return 0; 2626 } 2627 2628 static int set_txidle(struct slgt_info *info, int idle_mode) 2629 { 2630 unsigned long flags; 2631 DBGINFO(("%s set_txidle(%d)\n", info->device_name, idle_mode)); 2632 spin_lock_irqsave(&info->lock,flags); 2633 info->idle_mode = idle_mode; 2634 if (info->params.mode != MGSL_MODE_ASYNC) 2635 tx_set_idle(info); 2636 spin_unlock_irqrestore(&info->lock,flags); 2637 return 0; 2638 } 2639 2640 static int tx_enable(struct slgt_info *info, int enable) 2641 { 2642 unsigned long flags; 2643 DBGINFO(("%s tx_enable(%d)\n", info->device_name, enable)); 2644 spin_lock_irqsave(&info->lock,flags); 2645 if (enable) { 2646 if (!info->tx_enabled) 2647 tx_start(info); 2648 } else { 2649 if (info->tx_enabled) 2650 tx_stop(info); 2651 } 2652 spin_unlock_irqrestore(&info->lock,flags); 2653 return 0; 2654 } 2655 2656 /* 2657 * abort transmit HDLC frame 2658 */ 2659 static int tx_abort(struct slgt_info *info) 2660 { 2661 unsigned long flags; 2662 DBGINFO(("%s tx_abort\n", info->device_name)); 2663 spin_lock_irqsave(&info->lock,flags); 2664 tdma_reset(info); 2665 spin_unlock_irqrestore(&info->lock,flags); 2666 return 0; 2667 } 2668 2669 static int rx_enable(struct slgt_info *info, int enable) 2670 { 2671 unsigned long flags; 2672 unsigned int rbuf_fill_level; 2673 DBGINFO(("%s rx_enable(%08x)\n", info->device_name, enable)); 2674 spin_lock_irqsave(&info->lock,flags); 2675 /* 2676 * enable[31..16] = receive DMA buffer fill level 2677 * 0 = noop (leave fill level unchanged) 2678 * fill level must be multiple of 4 and <= buffer size 2679 */ 2680 rbuf_fill_level = ((unsigned int)enable) >> 16; 2681 if (rbuf_fill_level) { 2682 if ((rbuf_fill_level > DMABUFSIZE) || (rbuf_fill_level % 4)) { 2683 spin_unlock_irqrestore(&info->lock, flags); 2684 return -EINVAL; 2685 } 2686 info->rbuf_fill_level = rbuf_fill_level; 2687 if (rbuf_fill_level < 128) 2688 info->rx_pio = 1; /* PIO mode */ 2689 else 2690 info->rx_pio = 0; /* DMA mode */ 2691 rx_stop(info); /* restart receiver to use new fill level */ 2692 } 2693 2694 /* 2695 * enable[1..0] = receiver enable command 2696 * 0 = disable 2697 * 1 = enable 2698 * 2 = enable or force hunt mode if already enabled 2699 */ 2700 enable &= 3; 2701 if (enable) { 2702 if (!info->rx_enabled) 2703 rx_start(info); 2704 else if (enable == 2) { 2705 /* force hunt mode (write 1 to RCR[3]) */ 2706 wr_reg16(info, RCR, rd_reg16(info, RCR) | BIT3); 2707 } 2708 } else { 2709 if (info->rx_enabled) 2710 rx_stop(info); 2711 } 2712 spin_unlock_irqrestore(&info->lock,flags); 2713 return 0; 2714 } 2715 2716 /* 2717 * wait for specified event to occur 2718 */ 2719 static int wait_mgsl_event(struct slgt_info *info, int __user *mask_ptr) 2720 { 2721 unsigned long flags; 2722 int s; 2723 int rc=0; 2724 struct mgsl_icount cprev, cnow; 2725 int events; 2726 int mask; 2727 struct _input_signal_events oldsigs, newsigs; 2728 DECLARE_WAITQUEUE(wait, current); 2729 2730 if (get_user(mask, mask_ptr)) 2731 return -EFAULT; 2732 2733 DBGINFO(("%s wait_mgsl_event(%d)\n", info->device_name, mask)); 2734 2735 spin_lock_irqsave(&info->lock,flags); 2736 2737 /* return immediately if state matches requested events */ 2738 get_signals(info); 2739 s = info->signals; 2740 2741 events = mask & 2742 ( ((s & SerialSignal_DSR) ? MgslEvent_DsrActive:MgslEvent_DsrInactive) + 2743 ((s & SerialSignal_DCD) ? MgslEvent_DcdActive:MgslEvent_DcdInactive) + 2744 ((s & SerialSignal_CTS) ? MgslEvent_CtsActive:MgslEvent_CtsInactive) + 2745 ((s & SerialSignal_RI) ? MgslEvent_RiActive :MgslEvent_RiInactive) ); 2746 if (events) { 2747 spin_unlock_irqrestore(&info->lock,flags); 2748 goto exit; 2749 } 2750 2751 /* save current irq counts */ 2752 cprev = info->icount; 2753 oldsigs = info->input_signal_events; 2754 2755 /* enable hunt and idle irqs if needed */ 2756 if (mask & (MgslEvent_ExitHuntMode+MgslEvent_IdleReceived)) { 2757 unsigned short val = rd_reg16(info, SCR); 2758 if (!(val & IRQ_RXIDLE)) 2759 wr_reg16(info, SCR, (unsigned short)(val | IRQ_RXIDLE)); 2760 } 2761 2762 set_current_state(TASK_INTERRUPTIBLE); 2763 add_wait_queue(&info->event_wait_q, &wait); 2764 2765 spin_unlock_irqrestore(&info->lock,flags); 2766 2767 for(;;) { 2768 schedule(); 2769 if (signal_pending(current)) { 2770 rc = -ERESTARTSYS; 2771 break; 2772 } 2773 2774 /* get current irq counts */ 2775 spin_lock_irqsave(&info->lock,flags); 2776 cnow = info->icount; 2777 newsigs = info->input_signal_events; 2778 set_current_state(TASK_INTERRUPTIBLE); 2779 spin_unlock_irqrestore(&info->lock,flags); 2780 2781 /* if no change, wait aborted for some reason */ 2782 if (newsigs.dsr_up == oldsigs.dsr_up && 2783 newsigs.dsr_down == oldsigs.dsr_down && 2784 newsigs.dcd_up == oldsigs.dcd_up && 2785 newsigs.dcd_down == oldsigs.dcd_down && 2786 newsigs.cts_up == oldsigs.cts_up && 2787 newsigs.cts_down == oldsigs.cts_down && 2788 newsigs.ri_up == oldsigs.ri_up && 2789 newsigs.ri_down == oldsigs.ri_down && 2790 cnow.exithunt == cprev.exithunt && 2791 cnow.rxidle == cprev.rxidle) { 2792 rc = -EIO; 2793 break; 2794 } 2795 2796 events = mask & 2797 ( (newsigs.dsr_up != oldsigs.dsr_up ? MgslEvent_DsrActive:0) + 2798 (newsigs.dsr_down != oldsigs.dsr_down ? MgslEvent_DsrInactive:0) + 2799 (newsigs.dcd_up != oldsigs.dcd_up ? MgslEvent_DcdActive:0) + 2800 (newsigs.dcd_down != oldsigs.dcd_down ? MgslEvent_DcdInactive:0) + 2801 (newsigs.cts_up != oldsigs.cts_up ? MgslEvent_CtsActive:0) + 2802 (newsigs.cts_down != oldsigs.cts_down ? MgslEvent_CtsInactive:0) + 2803 (newsigs.ri_up != oldsigs.ri_up ? MgslEvent_RiActive:0) + 2804 (newsigs.ri_down != oldsigs.ri_down ? MgslEvent_RiInactive:0) + 2805 (cnow.exithunt != cprev.exithunt ? MgslEvent_ExitHuntMode:0) + 2806 (cnow.rxidle != cprev.rxidle ? MgslEvent_IdleReceived:0) ); 2807 if (events) 2808 break; 2809 2810 cprev = cnow; 2811 oldsigs = newsigs; 2812 } 2813 2814 remove_wait_queue(&info->event_wait_q, &wait); 2815 set_current_state(TASK_RUNNING); 2816 2817 2818 if (mask & (MgslEvent_ExitHuntMode + MgslEvent_IdleReceived)) { 2819 spin_lock_irqsave(&info->lock,flags); 2820 if (!waitqueue_active(&info->event_wait_q)) { 2821 /* disable enable exit hunt mode/idle rcvd IRQs */ 2822 wr_reg16(info, SCR, 2823 (unsigned short)(rd_reg16(info, SCR) & ~IRQ_RXIDLE)); 2824 } 2825 spin_unlock_irqrestore(&info->lock,flags); 2826 } 2827 exit: 2828 if (rc == 0) 2829 rc = put_user(events, mask_ptr); 2830 return rc; 2831 } 2832 2833 static int get_interface(struct slgt_info *info, int __user *if_mode) 2834 { 2835 DBGINFO(("%s get_interface=%x\n", info->device_name, info->if_mode)); 2836 if (put_user(info->if_mode, if_mode)) 2837 return -EFAULT; 2838 return 0; 2839 } 2840 2841 static int set_interface(struct slgt_info *info, int if_mode) 2842 { 2843 unsigned long flags; 2844 unsigned short val; 2845 2846 DBGINFO(("%s set_interface=%x)\n", info->device_name, if_mode)); 2847 spin_lock_irqsave(&info->lock,flags); 2848 info->if_mode = if_mode; 2849 2850 msc_set_vcr(info); 2851 2852 /* TCR (tx control) 07 1=RTS driver control */ 2853 val = rd_reg16(info, TCR); 2854 if (info->if_mode & MGSL_INTERFACE_RTS_EN) 2855 val |= BIT7; 2856 else 2857 val &= ~BIT7; 2858 wr_reg16(info, TCR, val); 2859 2860 spin_unlock_irqrestore(&info->lock,flags); 2861 return 0; 2862 } 2863 2864 static int get_xsync(struct slgt_info *info, int __user *xsync) 2865 { 2866 DBGINFO(("%s get_xsync=%x\n", info->device_name, info->xsync)); 2867 if (put_user(info->xsync, xsync)) 2868 return -EFAULT; 2869 return 0; 2870 } 2871 2872 /* 2873 * set extended sync pattern (1 to 4 bytes) for extended sync mode 2874 * 2875 * sync pattern is contained in least significant bytes of value 2876 * most significant byte of sync pattern is oldest (1st sent/detected) 2877 */ 2878 static int set_xsync(struct slgt_info *info, int xsync) 2879 { 2880 unsigned long flags; 2881 2882 DBGINFO(("%s set_xsync=%x)\n", info->device_name, xsync)); 2883 spin_lock_irqsave(&info->lock, flags); 2884 info->xsync = xsync; 2885 wr_reg32(info, XSR, xsync); 2886 spin_unlock_irqrestore(&info->lock, flags); 2887 return 0; 2888 } 2889 2890 static int get_xctrl(struct slgt_info *info, int __user *xctrl) 2891 { 2892 DBGINFO(("%s get_xctrl=%x\n", info->device_name, info->xctrl)); 2893 if (put_user(info->xctrl, xctrl)) 2894 return -EFAULT; 2895 return 0; 2896 } 2897 2898 /* 2899 * set extended control options 2900 * 2901 * xctrl[31:19] reserved, must be zero 2902 * xctrl[18:17] extended sync pattern length in bytes 2903 * 00 = 1 byte in xsr[7:0] 2904 * 01 = 2 bytes in xsr[15:0] 2905 * 10 = 3 bytes in xsr[23:0] 2906 * 11 = 4 bytes in xsr[31:0] 2907 * xctrl[16] 1 = enable terminal count, 0=disabled 2908 * xctrl[15:0] receive terminal count for fixed length packets 2909 * value is count minus one (0 = 1 byte packet) 2910 * when terminal count is reached, receiver 2911 * automatically returns to hunt mode and receive 2912 * FIFO contents are flushed to DMA buffers with 2913 * end of frame (EOF) status 2914 */ 2915 static int set_xctrl(struct slgt_info *info, int xctrl) 2916 { 2917 unsigned long flags; 2918 2919 DBGINFO(("%s set_xctrl=%x)\n", info->device_name, xctrl)); 2920 spin_lock_irqsave(&info->lock, flags); 2921 info->xctrl = xctrl; 2922 wr_reg32(info, XCR, xctrl); 2923 spin_unlock_irqrestore(&info->lock, flags); 2924 return 0; 2925 } 2926 2927 /* 2928 * set general purpose IO pin state and direction 2929 * 2930 * user_gpio fields: 2931 * state each bit indicates a pin state 2932 * smask set bit indicates pin state to set 2933 * dir each bit indicates a pin direction (0=input, 1=output) 2934 * dmask set bit indicates pin direction to set 2935 */ 2936 static int set_gpio(struct slgt_info *info, struct gpio_desc __user *user_gpio) 2937 { 2938 unsigned long flags; 2939 struct gpio_desc gpio; 2940 __u32 data; 2941 2942 if (!info->gpio_present) 2943 return -EINVAL; 2944 if (copy_from_user(&gpio, user_gpio, sizeof(gpio))) 2945 return -EFAULT; 2946 DBGINFO(("%s set_gpio state=%08x smask=%08x dir=%08x dmask=%08x\n", 2947 info->device_name, gpio.state, gpio.smask, 2948 gpio.dir, gpio.dmask)); 2949 2950 spin_lock_irqsave(&info->port_array[0]->lock, flags); 2951 if (gpio.dmask) { 2952 data = rd_reg32(info, IODR); 2953 data |= gpio.dmask & gpio.dir; 2954 data &= ~(gpio.dmask & ~gpio.dir); 2955 wr_reg32(info, IODR, data); 2956 } 2957 if (gpio.smask) { 2958 data = rd_reg32(info, IOVR); 2959 data |= gpio.smask & gpio.state; 2960 data &= ~(gpio.smask & ~gpio.state); 2961 wr_reg32(info, IOVR, data); 2962 } 2963 spin_unlock_irqrestore(&info->port_array[0]->lock, flags); 2964 2965 return 0; 2966 } 2967 2968 /* 2969 * get general purpose IO pin state and direction 2970 */ 2971 static int get_gpio(struct slgt_info *info, struct gpio_desc __user *user_gpio) 2972 { 2973 struct gpio_desc gpio; 2974 if (!info->gpio_present) 2975 return -EINVAL; 2976 gpio.state = rd_reg32(info, IOVR); 2977 gpio.smask = 0xffffffff; 2978 gpio.dir = rd_reg32(info, IODR); 2979 gpio.dmask = 0xffffffff; 2980 if (copy_to_user(user_gpio, &gpio, sizeof(gpio))) 2981 return -EFAULT; 2982 DBGINFO(("%s get_gpio state=%08x dir=%08x\n", 2983 info->device_name, gpio.state, gpio.dir)); 2984 return 0; 2985 } 2986 2987 /* 2988 * conditional wait facility 2989 */ 2990 static void init_cond_wait(struct cond_wait *w, unsigned int data) 2991 { 2992 init_waitqueue_head(&w->q); 2993 init_waitqueue_entry(&w->wait, current); 2994 w->data = data; 2995 } 2996 2997 static void add_cond_wait(struct cond_wait **head, struct cond_wait *w) 2998 { 2999 set_current_state(TASK_INTERRUPTIBLE); 3000 add_wait_queue(&w->q, &w->wait); 3001 w->next = *head; 3002 *head = w; 3003 } 3004 3005 static void remove_cond_wait(struct cond_wait **head, struct cond_wait *cw) 3006 { 3007 struct cond_wait *w, *prev; 3008 remove_wait_queue(&cw->q, &cw->wait); 3009 set_current_state(TASK_RUNNING); 3010 for (w = *head, prev = NULL ; w != NULL ; prev = w, w = w->next) { 3011 if (w == cw) { 3012 if (prev != NULL) 3013 prev->next = w->next; 3014 else 3015 *head = w->next; 3016 break; 3017 } 3018 } 3019 } 3020 3021 static void flush_cond_wait(struct cond_wait **head) 3022 { 3023 while (*head != NULL) { 3024 wake_up_interruptible(&(*head)->q); 3025 *head = (*head)->next; 3026 } 3027 } 3028 3029 /* 3030 * wait for general purpose I/O pin(s) to enter specified state 3031 * 3032 * user_gpio fields: 3033 * state - bit indicates target pin state 3034 * smask - set bit indicates watched pin 3035 * 3036 * The wait ends when at least one watched pin enters the specified 3037 * state. When 0 (no error) is returned, user_gpio->state is set to the 3038 * state of all GPIO pins when the wait ends. 3039 * 3040 * Note: Each pin may be a dedicated input, dedicated output, or 3041 * configurable input/output. The number and configuration of pins 3042 * varies with the specific adapter model. Only input pins (dedicated 3043 * or configured) can be monitored with this function. 3044 */ 3045 static int wait_gpio(struct slgt_info *info, struct gpio_desc __user *user_gpio) 3046 { 3047 unsigned long flags; 3048 int rc = 0; 3049 struct gpio_desc gpio; 3050 struct cond_wait wait; 3051 u32 state; 3052 3053 if (!info->gpio_present) 3054 return -EINVAL; 3055 if (copy_from_user(&gpio, user_gpio, sizeof(gpio))) 3056 return -EFAULT; 3057 DBGINFO(("%s wait_gpio() state=%08x smask=%08x\n", 3058 info->device_name, gpio.state, gpio.smask)); 3059 /* ignore output pins identified by set IODR bit */ 3060 if ((gpio.smask &= ~rd_reg32(info, IODR)) == 0) 3061 return -EINVAL; 3062 init_cond_wait(&wait, gpio.smask); 3063 3064 spin_lock_irqsave(&info->port_array[0]->lock, flags); 3065 /* enable interrupts for watched pins */ 3066 wr_reg32(info, IOER, rd_reg32(info, IOER) | gpio.smask); 3067 /* get current pin states */ 3068 state = rd_reg32(info, IOVR); 3069 3070 if (gpio.smask & ~(state ^ gpio.state)) { 3071 /* already in target state */ 3072 gpio.state = state; 3073 } else { 3074 /* wait for target state */ 3075 add_cond_wait(&info->gpio_wait_q, &wait); 3076 spin_unlock_irqrestore(&info->port_array[0]->lock, flags); 3077 schedule(); 3078 if (signal_pending(current)) 3079 rc = -ERESTARTSYS; 3080 else 3081 gpio.state = wait.data; 3082 spin_lock_irqsave(&info->port_array[0]->lock, flags); 3083 remove_cond_wait(&info->gpio_wait_q, &wait); 3084 } 3085 3086 /* disable all GPIO interrupts if no waiting processes */ 3087 if (info->gpio_wait_q == NULL) 3088 wr_reg32(info, IOER, 0); 3089 spin_unlock_irqrestore(&info->port_array[0]->lock, flags); 3090 3091 if ((rc == 0) && copy_to_user(user_gpio, &gpio, sizeof(gpio))) 3092 rc = -EFAULT; 3093 return rc; 3094 } 3095 3096 static int modem_input_wait(struct slgt_info *info,int arg) 3097 { 3098 unsigned long flags; 3099 int rc; 3100 struct mgsl_icount cprev, cnow; 3101 DECLARE_WAITQUEUE(wait, current); 3102 3103 /* save current irq counts */ 3104 spin_lock_irqsave(&info->lock,flags); 3105 cprev = info->icount; 3106 add_wait_queue(&info->status_event_wait_q, &wait); 3107 set_current_state(TASK_INTERRUPTIBLE); 3108 spin_unlock_irqrestore(&info->lock,flags); 3109 3110 for(;;) { 3111 schedule(); 3112 if (signal_pending(current)) { 3113 rc = -ERESTARTSYS; 3114 break; 3115 } 3116 3117 /* get new irq counts */ 3118 spin_lock_irqsave(&info->lock,flags); 3119 cnow = info->icount; 3120 set_current_state(TASK_INTERRUPTIBLE); 3121 spin_unlock_irqrestore(&info->lock,flags); 3122 3123 /* if no change, wait aborted for some reason */ 3124 if (cnow.rng == cprev.rng && cnow.dsr == cprev.dsr && 3125 cnow.dcd == cprev.dcd && cnow.cts == cprev.cts) { 3126 rc = -EIO; 3127 break; 3128 } 3129 3130 /* check for change in caller specified modem input */ 3131 if ((arg & TIOCM_RNG && cnow.rng != cprev.rng) || 3132 (arg & TIOCM_DSR && cnow.dsr != cprev.dsr) || 3133 (arg & TIOCM_CD && cnow.dcd != cprev.dcd) || 3134 (arg & TIOCM_CTS && cnow.cts != cprev.cts)) { 3135 rc = 0; 3136 break; 3137 } 3138 3139 cprev = cnow; 3140 } 3141 remove_wait_queue(&info->status_event_wait_q, &wait); 3142 set_current_state(TASK_RUNNING); 3143 return rc; 3144 } 3145 3146 /* 3147 * return state of serial control and status signals 3148 */ 3149 static int tiocmget(struct tty_struct *tty) 3150 { 3151 struct slgt_info *info = tty->driver_data; 3152 unsigned int result; 3153 unsigned long flags; 3154 3155 spin_lock_irqsave(&info->lock,flags); 3156 get_signals(info); 3157 spin_unlock_irqrestore(&info->lock,flags); 3158 3159 result = ((info->signals & SerialSignal_RTS) ? TIOCM_RTS:0) + 3160 ((info->signals & SerialSignal_DTR) ? TIOCM_DTR:0) + 3161 ((info->signals & SerialSignal_DCD) ? TIOCM_CAR:0) + 3162 ((info->signals & SerialSignal_RI) ? TIOCM_RNG:0) + 3163 ((info->signals & SerialSignal_DSR) ? TIOCM_DSR:0) + 3164 ((info->signals & SerialSignal_CTS) ? TIOCM_CTS:0); 3165 3166 DBGINFO(("%s tiocmget value=%08X\n", info->device_name, result)); 3167 return result; 3168 } 3169 3170 /* 3171 * set modem control signals (DTR/RTS) 3172 * 3173 * cmd signal command: TIOCMBIS = set bit TIOCMBIC = clear bit 3174 * TIOCMSET = set/clear signal values 3175 * value bit mask for command 3176 */ 3177 static int tiocmset(struct tty_struct *tty, 3178 unsigned int set, unsigned int clear) 3179 { 3180 struct slgt_info *info = tty->driver_data; 3181 unsigned long flags; 3182 3183 DBGINFO(("%s tiocmset(%x,%x)\n", info->device_name, set, clear)); 3184 3185 if (set & TIOCM_RTS) 3186 info->signals |= SerialSignal_RTS; 3187 if (set & TIOCM_DTR) 3188 info->signals |= SerialSignal_DTR; 3189 if (clear & TIOCM_RTS) 3190 info->signals &= ~SerialSignal_RTS; 3191 if (clear & TIOCM_DTR) 3192 info->signals &= ~SerialSignal_DTR; 3193 3194 spin_lock_irqsave(&info->lock,flags); 3195 set_signals(info); 3196 spin_unlock_irqrestore(&info->lock,flags); 3197 return 0; 3198 } 3199 3200 static int carrier_raised(struct tty_port *port) 3201 { 3202 unsigned long flags; 3203 struct slgt_info *info = container_of(port, struct slgt_info, port); 3204 3205 spin_lock_irqsave(&info->lock,flags); 3206 get_signals(info); 3207 spin_unlock_irqrestore(&info->lock,flags); 3208 return (info->signals & SerialSignal_DCD) ? 1 : 0; 3209 } 3210 3211 static void dtr_rts(struct tty_port *port, int on) 3212 { 3213 unsigned long flags; 3214 struct slgt_info *info = container_of(port, struct slgt_info, port); 3215 3216 spin_lock_irqsave(&info->lock,flags); 3217 if (on) 3218 info->signals |= SerialSignal_RTS | SerialSignal_DTR; 3219 else 3220 info->signals &= ~(SerialSignal_RTS | SerialSignal_DTR); 3221 set_signals(info); 3222 spin_unlock_irqrestore(&info->lock,flags); 3223 } 3224 3225 3226 /* 3227 * block current process until the device is ready to open 3228 */ 3229 static int block_til_ready(struct tty_struct *tty, struct file *filp, 3230 struct slgt_info *info) 3231 { 3232 DECLARE_WAITQUEUE(wait, current); 3233 int retval; 3234 bool do_clocal = false; 3235 unsigned long flags; 3236 int cd; 3237 struct tty_port *port = &info->port; 3238 3239 DBGINFO(("%s block_til_ready\n", tty->driver->name)); 3240 3241 if (filp->f_flags & O_NONBLOCK || tty_io_error(tty)) { 3242 /* nonblock mode is set or port is not enabled */ 3243 tty_port_set_active(port, 1); 3244 return 0; 3245 } 3246 3247 if (C_CLOCAL(tty)) 3248 do_clocal = true; 3249 3250 /* Wait for carrier detect and the line to become 3251 * free (i.e., not in use by the callout). While we are in 3252 * this loop, port->count is dropped by one, so that 3253 * close() knows when to free things. We restore it upon 3254 * exit, either normal or abnormal. 3255 */ 3256 3257 retval = 0; 3258 add_wait_queue(&port->open_wait, &wait); 3259 3260 spin_lock_irqsave(&info->lock, flags); 3261 port->count--; 3262 spin_unlock_irqrestore(&info->lock, flags); 3263 port->blocked_open++; 3264 3265 while (1) { 3266 if (C_BAUD(tty) && tty_port_initialized(port)) 3267 tty_port_raise_dtr_rts(port); 3268 3269 set_current_state(TASK_INTERRUPTIBLE); 3270 3271 if (tty_hung_up_p(filp) || !tty_port_initialized(port)) { 3272 retval = (port->flags & ASYNC_HUP_NOTIFY) ? 3273 -EAGAIN : -ERESTARTSYS; 3274 break; 3275 } 3276 3277 cd = tty_port_carrier_raised(port); 3278 if (do_clocal || cd) 3279 break; 3280 3281 if (signal_pending(current)) { 3282 retval = -ERESTARTSYS; 3283 break; 3284 } 3285 3286 DBGINFO(("%s block_til_ready wait\n", tty->driver->name)); 3287 tty_unlock(tty); 3288 schedule(); 3289 tty_lock(tty); 3290 } 3291 3292 set_current_state(TASK_RUNNING); 3293 remove_wait_queue(&port->open_wait, &wait); 3294 3295 if (!tty_hung_up_p(filp)) 3296 port->count++; 3297 port->blocked_open--; 3298 3299 if (!retval) 3300 tty_port_set_active(port, 1); 3301 3302 DBGINFO(("%s block_til_ready ready, rc=%d\n", tty->driver->name, retval)); 3303 return retval; 3304 } 3305 3306 /* 3307 * allocate buffers used for calling line discipline receive_buf 3308 * directly in synchronous mode 3309 * note: add 5 bytes to max frame size to allow appending 3310 * 32-bit CRC and status byte when configured to do so 3311 */ 3312 static int alloc_tmp_rbuf(struct slgt_info *info) 3313 { 3314 info->tmp_rbuf = kmalloc(info->max_frame_size + 5, GFP_KERNEL); 3315 if (info->tmp_rbuf == NULL) 3316 return -ENOMEM; 3317 /* unused flag buffer to satisfy receive_buf calling interface */ 3318 info->flag_buf = kzalloc(info->max_frame_size + 5, GFP_KERNEL); 3319 if (!info->flag_buf) { 3320 kfree(info->tmp_rbuf); 3321 info->tmp_rbuf = NULL; 3322 return -ENOMEM; 3323 } 3324 return 0; 3325 } 3326 3327 static void free_tmp_rbuf(struct slgt_info *info) 3328 { 3329 kfree(info->tmp_rbuf); 3330 info->tmp_rbuf = NULL; 3331 kfree(info->flag_buf); 3332 info->flag_buf = NULL; 3333 } 3334 3335 /* 3336 * allocate DMA descriptor lists. 3337 */ 3338 static int alloc_desc(struct slgt_info *info) 3339 { 3340 unsigned int i; 3341 unsigned int pbufs; 3342 3343 /* allocate memory to hold descriptor lists */ 3344 info->bufs = pci_zalloc_consistent(info->pdev, DESC_LIST_SIZE, 3345 &info->bufs_dma_addr); 3346 if (info->bufs == NULL) 3347 return -ENOMEM; 3348 3349 info->rbufs = (struct slgt_desc*)info->bufs; 3350 info->tbufs = ((struct slgt_desc*)info->bufs) + info->rbuf_count; 3351 3352 pbufs = (unsigned int)info->bufs_dma_addr; 3353 3354 /* 3355 * Build circular lists of descriptors 3356 */ 3357 3358 for (i=0; i < info->rbuf_count; i++) { 3359 /* physical address of this descriptor */ 3360 info->rbufs[i].pdesc = pbufs + (i * sizeof(struct slgt_desc)); 3361 3362 /* physical address of next descriptor */ 3363 if (i == info->rbuf_count - 1) 3364 info->rbufs[i].next = cpu_to_le32(pbufs); 3365 else 3366 info->rbufs[i].next = cpu_to_le32(pbufs + ((i+1) * sizeof(struct slgt_desc))); 3367 set_desc_count(info->rbufs[i], DMABUFSIZE); 3368 } 3369 3370 for (i=0; i < info->tbuf_count; i++) { 3371 /* physical address of this descriptor */ 3372 info->tbufs[i].pdesc = pbufs + ((info->rbuf_count + i) * sizeof(struct slgt_desc)); 3373 3374 /* physical address of next descriptor */ 3375 if (i == info->tbuf_count - 1) 3376 info->tbufs[i].next = cpu_to_le32(pbufs + info->rbuf_count * sizeof(struct slgt_desc)); 3377 else 3378 info->tbufs[i].next = cpu_to_le32(pbufs + ((info->rbuf_count + i + 1) * sizeof(struct slgt_desc))); 3379 } 3380 3381 return 0; 3382 } 3383 3384 static void free_desc(struct slgt_info *info) 3385 { 3386 if (info->bufs != NULL) { 3387 pci_free_consistent(info->pdev, DESC_LIST_SIZE, info->bufs, info->bufs_dma_addr); 3388 info->bufs = NULL; 3389 info->rbufs = NULL; 3390 info->tbufs = NULL; 3391 } 3392 } 3393 3394 static int alloc_bufs(struct slgt_info *info, struct slgt_desc *bufs, int count) 3395 { 3396 int i; 3397 for (i=0; i < count; i++) { 3398 if ((bufs[i].buf = pci_alloc_consistent(info->pdev, DMABUFSIZE, &bufs[i].buf_dma_addr)) == NULL) 3399 return -ENOMEM; 3400 bufs[i].pbuf = cpu_to_le32((unsigned int)bufs[i].buf_dma_addr); 3401 } 3402 return 0; 3403 } 3404 3405 static void free_bufs(struct slgt_info *info, struct slgt_desc *bufs, int count) 3406 { 3407 int i; 3408 for (i=0; i < count; i++) { 3409 if (bufs[i].buf == NULL) 3410 continue; 3411 pci_free_consistent(info->pdev, DMABUFSIZE, bufs[i].buf, bufs[i].buf_dma_addr); 3412 bufs[i].buf = NULL; 3413 } 3414 } 3415 3416 static int alloc_dma_bufs(struct slgt_info *info) 3417 { 3418 info->rbuf_count = 32; 3419 info->tbuf_count = 32; 3420 3421 if (alloc_desc(info) < 0 || 3422 alloc_bufs(info, info->rbufs, info->rbuf_count) < 0 || 3423 alloc_bufs(info, info->tbufs, info->tbuf_count) < 0 || 3424 alloc_tmp_rbuf(info) < 0) { 3425 DBGERR(("%s DMA buffer alloc fail\n", info->device_name)); 3426 return -ENOMEM; 3427 } 3428 reset_rbufs(info); 3429 return 0; 3430 } 3431 3432 static void free_dma_bufs(struct slgt_info *info) 3433 { 3434 if (info->bufs) { 3435 free_bufs(info, info->rbufs, info->rbuf_count); 3436 free_bufs(info, info->tbufs, info->tbuf_count); 3437 free_desc(info); 3438 } 3439 free_tmp_rbuf(info); 3440 } 3441 3442 static int claim_resources(struct slgt_info *info) 3443 { 3444 if (request_mem_region(info->phys_reg_addr, SLGT_REG_SIZE, "synclink_gt") == NULL) { 3445 DBGERR(("%s reg addr conflict, addr=%08X\n", 3446 info->device_name, info->phys_reg_addr)); 3447 info->init_error = DiagStatus_AddressConflict; 3448 goto errout; 3449 } 3450 else 3451 info->reg_addr_requested = true; 3452 3453 info->reg_addr = ioremap_nocache(info->phys_reg_addr, SLGT_REG_SIZE); 3454 if (!info->reg_addr) { 3455 DBGERR(("%s can't map device registers, addr=%08X\n", 3456 info->device_name, info->phys_reg_addr)); 3457 info->init_error = DiagStatus_CantAssignPciResources; 3458 goto errout; 3459 } 3460 return 0; 3461 3462 errout: 3463 release_resources(info); 3464 return -ENODEV; 3465 } 3466 3467 static void release_resources(struct slgt_info *info) 3468 { 3469 if (info->irq_requested) { 3470 free_irq(info->irq_level, info); 3471 info->irq_requested = false; 3472 } 3473 3474 if (info->reg_addr_requested) { 3475 release_mem_region(info->phys_reg_addr, SLGT_REG_SIZE); 3476 info->reg_addr_requested = false; 3477 } 3478 3479 if (info->reg_addr) { 3480 iounmap(info->reg_addr); 3481 info->reg_addr = NULL; 3482 } 3483 } 3484 3485 /* Add the specified device instance data structure to the 3486 * global linked list of devices and increment the device count. 3487 */ 3488 static void add_device(struct slgt_info *info) 3489 { 3490 char *devstr; 3491 3492 info->next_device = NULL; 3493 info->line = slgt_device_count; 3494 sprintf(info->device_name, "%s%d", tty_dev_prefix, info->line); 3495 3496 if (info->line < MAX_DEVICES) { 3497 if (maxframe[info->line]) 3498 info->max_frame_size = maxframe[info->line]; 3499 } 3500 3501 slgt_device_count++; 3502 3503 if (!slgt_device_list) 3504 slgt_device_list = info; 3505 else { 3506 struct slgt_info *current_dev = slgt_device_list; 3507 while(current_dev->next_device) 3508 current_dev = current_dev->next_device; 3509 current_dev->next_device = info; 3510 } 3511 3512 if (info->max_frame_size < 4096) 3513 info->max_frame_size = 4096; 3514 else if (info->max_frame_size > 65535) 3515 info->max_frame_size = 65535; 3516 3517 switch(info->pdev->device) { 3518 case SYNCLINK_GT_DEVICE_ID: 3519 devstr = "GT"; 3520 break; 3521 case SYNCLINK_GT2_DEVICE_ID: 3522 devstr = "GT2"; 3523 break; 3524 case SYNCLINK_GT4_DEVICE_ID: 3525 devstr = "GT4"; 3526 break; 3527 case SYNCLINK_AC_DEVICE_ID: 3528 devstr = "AC"; 3529 info->params.mode = MGSL_MODE_ASYNC; 3530 break; 3531 default: 3532 devstr = "(unknown model)"; 3533 } 3534 printk("SyncLink %s %s IO=%08x IRQ=%d MaxFrameSize=%u\n", 3535 devstr, info->device_name, info->phys_reg_addr, 3536 info->irq_level, info->max_frame_size); 3537 3538 #if SYNCLINK_GENERIC_HDLC 3539 hdlcdev_init(info); 3540 #endif 3541 } 3542 3543 static const struct tty_port_operations slgt_port_ops = { 3544 .carrier_raised = carrier_raised, 3545 .dtr_rts = dtr_rts, 3546 }; 3547 3548 /* 3549 * allocate device instance structure, return NULL on failure 3550 */ 3551 static struct slgt_info *alloc_dev(int adapter_num, int port_num, struct pci_dev *pdev) 3552 { 3553 struct slgt_info *info; 3554 3555 info = kzalloc(sizeof(struct slgt_info), GFP_KERNEL); 3556 3557 if (!info) { 3558 DBGERR(("%s device alloc failed adapter=%d port=%d\n", 3559 driver_name, adapter_num, port_num)); 3560 } else { 3561 tty_port_init(&info->port); 3562 info->port.ops = &slgt_port_ops; 3563 info->magic = MGSL_MAGIC; 3564 INIT_WORK(&info->task, bh_handler); 3565 info->max_frame_size = 4096; 3566 info->base_clock = 14745600; 3567 info->rbuf_fill_level = DMABUFSIZE; 3568 info->port.close_delay = 5*HZ/10; 3569 info->port.closing_wait = 30*HZ; 3570 init_waitqueue_head(&info->status_event_wait_q); 3571 init_waitqueue_head(&info->event_wait_q); 3572 spin_lock_init(&info->netlock); 3573 memcpy(&info->params,&default_params,sizeof(MGSL_PARAMS)); 3574 info->idle_mode = HDLC_TXIDLE_FLAGS; 3575 info->adapter_num = adapter_num; 3576 info->port_num = port_num; 3577 3578 timer_setup(&info->tx_timer, tx_timeout, 0); 3579 timer_setup(&info->rx_timer, rx_timeout, 0); 3580 3581 /* Copy configuration info to device instance data */ 3582 info->pdev = pdev; 3583 info->irq_level = pdev->irq; 3584 info->phys_reg_addr = pci_resource_start(pdev,0); 3585 3586 info->bus_type = MGSL_BUS_TYPE_PCI; 3587 info->irq_flags = IRQF_SHARED; 3588 3589 info->init_error = -1; /* assume error, set to 0 on successful init */ 3590 } 3591 3592 return info; 3593 } 3594 3595 static void device_init(int adapter_num, struct pci_dev *pdev) 3596 { 3597 struct slgt_info *port_array[SLGT_MAX_PORTS]; 3598 int i; 3599 int port_count = 1; 3600 3601 if (pdev->device == SYNCLINK_GT2_DEVICE_ID) 3602 port_count = 2; 3603 else if (pdev->device == SYNCLINK_GT4_DEVICE_ID) 3604 port_count = 4; 3605 3606 /* allocate device instances for all ports */ 3607 for (i=0; i < port_count; ++i) { 3608 port_array[i] = alloc_dev(adapter_num, i, pdev); 3609 if (port_array[i] == NULL) { 3610 for (--i; i >= 0; --i) { 3611 tty_port_destroy(&port_array[i]->port); 3612 kfree(port_array[i]); 3613 } 3614 return; 3615 } 3616 } 3617 3618 /* give copy of port_array to all ports and add to device list */ 3619 for (i=0; i < port_count; ++i) { 3620 memcpy(port_array[i]->port_array, port_array, sizeof(port_array)); 3621 add_device(port_array[i]); 3622 port_array[i]->port_count = port_count; 3623 spin_lock_init(&port_array[i]->lock); 3624 } 3625 3626 /* Allocate and claim adapter resources */ 3627 if (!claim_resources(port_array[0])) { 3628 3629 alloc_dma_bufs(port_array[0]); 3630 3631 /* copy resource information from first port to others */ 3632 for (i = 1; i < port_count; ++i) { 3633 port_array[i]->irq_level = port_array[0]->irq_level; 3634 port_array[i]->reg_addr = port_array[0]->reg_addr; 3635 alloc_dma_bufs(port_array[i]); 3636 } 3637 3638 if (request_irq(port_array[0]->irq_level, 3639 slgt_interrupt, 3640 port_array[0]->irq_flags, 3641 port_array[0]->device_name, 3642 port_array[0]) < 0) { 3643 DBGERR(("%s request_irq failed IRQ=%d\n", 3644 port_array[0]->device_name, 3645 port_array[0]->irq_level)); 3646 } else { 3647 port_array[0]->irq_requested = true; 3648 adapter_test(port_array[0]); 3649 for (i=1 ; i < port_count ; i++) { 3650 port_array[i]->init_error = port_array[0]->init_error; 3651 port_array[i]->gpio_present = port_array[0]->gpio_present; 3652 } 3653 } 3654 } 3655 3656 for (i = 0; i < port_count; ++i) { 3657 struct slgt_info *info = port_array[i]; 3658 tty_port_register_device(&info->port, serial_driver, info->line, 3659 &info->pdev->dev); 3660 } 3661 } 3662 3663 static int init_one(struct pci_dev *dev, 3664 const struct pci_device_id *ent) 3665 { 3666 if (pci_enable_device(dev)) { 3667 printk("error enabling pci device %p\n", dev); 3668 return -EIO; 3669 } 3670 pci_set_master(dev); 3671 device_init(slgt_device_count, dev); 3672 return 0; 3673 } 3674 3675 static void remove_one(struct pci_dev *dev) 3676 { 3677 } 3678 3679 static const struct tty_operations ops = { 3680 .open = open, 3681 .close = close, 3682 .write = write, 3683 .put_char = put_char, 3684 .flush_chars = flush_chars, 3685 .write_room = write_room, 3686 .chars_in_buffer = chars_in_buffer, 3687 .flush_buffer = flush_buffer, 3688 .ioctl = ioctl, 3689 .compat_ioctl = slgt_compat_ioctl, 3690 .throttle = throttle, 3691 .unthrottle = unthrottle, 3692 .send_xchar = send_xchar, 3693 .break_ctl = set_break, 3694 .wait_until_sent = wait_until_sent, 3695 .set_termios = set_termios, 3696 .stop = tx_hold, 3697 .start = tx_release, 3698 .hangup = hangup, 3699 .tiocmget = tiocmget, 3700 .tiocmset = tiocmset, 3701 .get_icount = get_icount, 3702 .proc_show = synclink_gt_proc_show, 3703 }; 3704 3705 static void slgt_cleanup(void) 3706 { 3707 int rc; 3708 struct slgt_info *info; 3709 struct slgt_info *tmp; 3710 3711 printk(KERN_INFO "unload %s\n", driver_name); 3712 3713 if (serial_driver) { 3714 for (info=slgt_device_list ; info != NULL ; info=info->next_device) 3715 tty_unregister_device(serial_driver, info->line); 3716 rc = tty_unregister_driver(serial_driver); 3717 if (rc) 3718 DBGERR(("tty_unregister_driver error=%d\n", rc)); 3719 put_tty_driver(serial_driver); 3720 } 3721 3722 /* reset devices */ 3723 info = slgt_device_list; 3724 while(info) { 3725 reset_port(info); 3726 info = info->next_device; 3727 } 3728 3729 /* release devices */ 3730 info = slgt_device_list; 3731 while(info) { 3732 #if SYNCLINK_GENERIC_HDLC 3733 hdlcdev_exit(info); 3734 #endif 3735 free_dma_bufs(info); 3736 free_tmp_rbuf(info); 3737 if (info->port_num == 0) 3738 release_resources(info); 3739 tmp = info; 3740 info = info->next_device; 3741 tty_port_destroy(&tmp->port); 3742 kfree(tmp); 3743 } 3744 3745 if (pci_registered) 3746 pci_unregister_driver(&pci_driver); 3747 } 3748 3749 /* 3750 * Driver initialization entry point. 3751 */ 3752 static int __init slgt_init(void) 3753 { 3754 int rc; 3755 3756 printk(KERN_INFO "%s\n", driver_name); 3757 3758 serial_driver = alloc_tty_driver(MAX_DEVICES); 3759 if (!serial_driver) { 3760 printk("%s can't allocate tty driver\n", driver_name); 3761 return -ENOMEM; 3762 } 3763 3764 /* Initialize the tty_driver structure */ 3765 3766 serial_driver->driver_name = slgt_driver_name; 3767 serial_driver->name = tty_dev_prefix; 3768 serial_driver->major = ttymajor; 3769 serial_driver->minor_start = 64; 3770 serial_driver->type = TTY_DRIVER_TYPE_SERIAL; 3771 serial_driver->subtype = SERIAL_TYPE_NORMAL; 3772 serial_driver->init_termios = tty_std_termios; 3773 serial_driver->init_termios.c_cflag = 3774 B9600 | CS8 | CREAD | HUPCL | CLOCAL; 3775 serial_driver->init_termios.c_ispeed = 9600; 3776 serial_driver->init_termios.c_ospeed = 9600; 3777 serial_driver->flags = TTY_DRIVER_REAL_RAW | TTY_DRIVER_DYNAMIC_DEV; 3778 tty_set_operations(serial_driver, &ops); 3779 if ((rc = tty_register_driver(serial_driver)) < 0) { 3780 DBGERR(("%s can't register serial driver\n", driver_name)); 3781 put_tty_driver(serial_driver); 3782 serial_driver = NULL; 3783 goto error; 3784 } 3785 3786 printk(KERN_INFO "%s, tty major#%d\n", 3787 driver_name, serial_driver->major); 3788 3789 slgt_device_count = 0; 3790 if ((rc = pci_register_driver(&pci_driver)) < 0) { 3791 printk("%s pci_register_driver error=%d\n", driver_name, rc); 3792 goto error; 3793 } 3794 pci_registered = true; 3795 3796 if (!slgt_device_list) 3797 printk("%s no devices found\n",driver_name); 3798 3799 return 0; 3800 3801 error: 3802 slgt_cleanup(); 3803 return rc; 3804 } 3805 3806 static void __exit slgt_exit(void) 3807 { 3808 slgt_cleanup(); 3809 } 3810 3811 module_init(slgt_init); 3812 module_exit(slgt_exit); 3813 3814 /* 3815 * register access routines 3816 */ 3817 3818 #define CALC_REGADDR() \ 3819 unsigned long reg_addr = ((unsigned long)info->reg_addr) + addr; \ 3820 if (addr >= 0x80) \ 3821 reg_addr += (info->port_num) * 32; \ 3822 else if (addr >= 0x40) \ 3823 reg_addr += (info->port_num) * 16; 3824 3825 static __u8 rd_reg8(struct slgt_info *info, unsigned int addr) 3826 { 3827 CALC_REGADDR(); 3828 return readb((void __iomem *)reg_addr); 3829 } 3830 3831 static void wr_reg8(struct slgt_info *info, unsigned int addr, __u8 value) 3832 { 3833 CALC_REGADDR(); 3834 writeb(value, (void __iomem *)reg_addr); 3835 } 3836 3837 static __u16 rd_reg16(struct slgt_info *info, unsigned int addr) 3838 { 3839 CALC_REGADDR(); 3840 return readw((void __iomem *)reg_addr); 3841 } 3842 3843 static void wr_reg16(struct slgt_info *info, unsigned int addr, __u16 value) 3844 { 3845 CALC_REGADDR(); 3846 writew(value, (void __iomem *)reg_addr); 3847 } 3848 3849 static __u32 rd_reg32(struct slgt_info *info, unsigned int addr) 3850 { 3851 CALC_REGADDR(); 3852 return readl((void __iomem *)reg_addr); 3853 } 3854 3855 static void wr_reg32(struct slgt_info *info, unsigned int addr, __u32 value) 3856 { 3857 CALC_REGADDR(); 3858 writel(value, (void __iomem *)reg_addr); 3859 } 3860 3861 static void rdma_reset(struct slgt_info *info) 3862 { 3863 unsigned int i; 3864 3865 /* set reset bit */ 3866 wr_reg32(info, RDCSR, BIT1); 3867 3868 /* wait for enable bit cleared */ 3869 for(i=0 ; i < 1000 ; i++) 3870 if (!(rd_reg32(info, RDCSR) & BIT0)) 3871 break; 3872 } 3873 3874 static void tdma_reset(struct slgt_info *info) 3875 { 3876 unsigned int i; 3877 3878 /* set reset bit */ 3879 wr_reg32(info, TDCSR, BIT1); 3880 3881 /* wait for enable bit cleared */ 3882 for(i=0 ; i < 1000 ; i++) 3883 if (!(rd_reg32(info, TDCSR) & BIT0)) 3884 break; 3885 } 3886 3887 /* 3888 * enable internal loopback 3889 * TxCLK and RxCLK are generated from BRG 3890 * and TxD is looped back to RxD internally. 3891 */ 3892 static void enable_loopback(struct slgt_info *info) 3893 { 3894 /* SCR (serial control) BIT2=loopback enable */ 3895 wr_reg16(info, SCR, (unsigned short)(rd_reg16(info, SCR) | BIT2)); 3896 3897 if (info->params.mode != MGSL_MODE_ASYNC) { 3898 /* CCR (clock control) 3899 * 07..05 tx clock source (010 = BRG) 3900 * 04..02 rx clock source (010 = BRG) 3901 * 01 auxclk enable (0 = disable) 3902 * 00 BRG enable (1 = enable) 3903 * 3904 * 0100 1001 3905 */ 3906 wr_reg8(info, CCR, 0x49); 3907 3908 /* set speed if available, otherwise use default */ 3909 if (info->params.clock_speed) 3910 set_rate(info, info->params.clock_speed); 3911 else 3912 set_rate(info, 3686400); 3913 } 3914 } 3915 3916 /* 3917 * set baud rate generator to specified rate 3918 */ 3919 static void set_rate(struct slgt_info *info, u32 rate) 3920 { 3921 unsigned int div; 3922 unsigned int osc = info->base_clock; 3923 3924 /* div = osc/rate - 1 3925 * 3926 * Round div up if osc/rate is not integer to 3927 * force to next slowest rate. 3928 */ 3929 3930 if (rate) { 3931 div = osc/rate; 3932 if (!(osc % rate) && div) 3933 div--; 3934 wr_reg16(info, BDR, (unsigned short)div); 3935 } 3936 } 3937 3938 static void rx_stop(struct slgt_info *info) 3939 { 3940 unsigned short val; 3941 3942 /* disable and reset receiver */ 3943 val = rd_reg16(info, RCR) & ~BIT1; /* clear enable bit */ 3944 wr_reg16(info, RCR, (unsigned short)(val | BIT2)); /* set reset bit */ 3945 wr_reg16(info, RCR, val); /* clear reset bit */ 3946 3947 slgt_irq_off(info, IRQ_RXOVER + IRQ_RXDATA + IRQ_RXIDLE); 3948 3949 /* clear pending rx interrupts */ 3950 wr_reg16(info, SSR, IRQ_RXIDLE + IRQ_RXOVER); 3951 3952 rdma_reset(info); 3953 3954 info->rx_enabled = false; 3955 info->rx_restart = false; 3956 } 3957 3958 static void rx_start(struct slgt_info *info) 3959 { 3960 unsigned short val; 3961 3962 slgt_irq_off(info, IRQ_RXOVER + IRQ_RXDATA); 3963 3964 /* clear pending rx overrun IRQ */ 3965 wr_reg16(info, SSR, IRQ_RXOVER); 3966 3967 /* reset and disable receiver */ 3968 val = rd_reg16(info, RCR) & ~BIT1; /* clear enable bit */ 3969 wr_reg16(info, RCR, (unsigned short)(val | BIT2)); /* set reset bit */ 3970 wr_reg16(info, RCR, val); /* clear reset bit */ 3971 3972 rdma_reset(info); 3973 reset_rbufs(info); 3974 3975 if (info->rx_pio) { 3976 /* rx request when rx FIFO not empty */ 3977 wr_reg16(info, SCR, (unsigned short)(rd_reg16(info, SCR) & ~BIT14)); 3978 slgt_irq_on(info, IRQ_RXDATA); 3979 if (info->params.mode == MGSL_MODE_ASYNC) { 3980 /* enable saving of rx status */ 3981 wr_reg32(info, RDCSR, BIT6); 3982 } 3983 } else { 3984 /* rx request when rx FIFO half full */ 3985 wr_reg16(info, SCR, (unsigned short)(rd_reg16(info, SCR) | BIT14)); 3986 /* set 1st descriptor address */ 3987 wr_reg32(info, RDDAR, info->rbufs[0].pdesc); 3988 3989 if (info->params.mode != MGSL_MODE_ASYNC) { 3990 /* enable rx DMA and DMA interrupt */ 3991 wr_reg32(info, RDCSR, (BIT2 + BIT0)); 3992 } else { 3993 /* enable saving of rx status, rx DMA and DMA interrupt */ 3994 wr_reg32(info, RDCSR, (BIT6 + BIT2 + BIT0)); 3995 } 3996 } 3997 3998 slgt_irq_on(info, IRQ_RXOVER); 3999 4000 /* enable receiver */ 4001 wr_reg16(info, RCR, (unsigned short)(rd_reg16(info, RCR) | BIT1)); 4002 4003 info->rx_restart = false; 4004 info->rx_enabled = true; 4005 } 4006 4007 static void tx_start(struct slgt_info *info) 4008 { 4009 if (!info->tx_enabled) { 4010 wr_reg16(info, TCR, 4011 (unsigned short)((rd_reg16(info, TCR) | BIT1) & ~BIT2)); 4012 info->tx_enabled = true; 4013 } 4014 4015 if (desc_count(info->tbufs[info->tbuf_start])) { 4016 info->drop_rts_on_tx_done = false; 4017 4018 if (info->params.mode != MGSL_MODE_ASYNC) { 4019 if (info->params.flags & HDLC_FLAG_AUTO_RTS) { 4020 get_signals(info); 4021 if (!(info->signals & SerialSignal_RTS)) { 4022 info->signals |= SerialSignal_RTS; 4023 set_signals(info); 4024 info->drop_rts_on_tx_done = true; 4025 } 4026 } 4027 4028 slgt_irq_off(info, IRQ_TXDATA); 4029 slgt_irq_on(info, IRQ_TXUNDER + IRQ_TXIDLE); 4030 /* clear tx idle and underrun status bits */ 4031 wr_reg16(info, SSR, (unsigned short)(IRQ_TXIDLE + IRQ_TXUNDER)); 4032 } else { 4033 slgt_irq_off(info, IRQ_TXDATA); 4034 slgt_irq_on(info, IRQ_TXIDLE); 4035 /* clear tx idle status bit */ 4036 wr_reg16(info, SSR, IRQ_TXIDLE); 4037 } 4038 /* set 1st descriptor address and start DMA */ 4039 wr_reg32(info, TDDAR, info->tbufs[info->tbuf_start].pdesc); 4040 wr_reg32(info, TDCSR, BIT2 + BIT0); 4041 info->tx_active = true; 4042 } 4043 } 4044 4045 static void tx_stop(struct slgt_info *info) 4046 { 4047 unsigned short val; 4048 4049 del_timer(&info->tx_timer); 4050 4051 tdma_reset(info); 4052 4053 /* reset and disable transmitter */ 4054 val = rd_reg16(info, TCR) & ~BIT1; /* clear enable bit */ 4055 wr_reg16(info, TCR, (unsigned short)(val | BIT2)); /* set reset bit */ 4056 4057 slgt_irq_off(info, IRQ_TXDATA + IRQ_TXIDLE + IRQ_TXUNDER); 4058 4059 /* clear tx idle and underrun status bit */ 4060 wr_reg16(info, SSR, (unsigned short)(IRQ_TXIDLE + IRQ_TXUNDER)); 4061 4062 reset_tbufs(info); 4063 4064 info->tx_enabled = false; 4065 info->tx_active = false; 4066 } 4067 4068 static void reset_port(struct slgt_info *info) 4069 { 4070 if (!info->reg_addr) 4071 return; 4072 4073 tx_stop(info); 4074 rx_stop(info); 4075 4076 info->signals &= ~(SerialSignal_RTS | SerialSignal_DTR); 4077 set_signals(info); 4078 4079 slgt_irq_off(info, IRQ_ALL | IRQ_MASTER); 4080 } 4081 4082 static void reset_adapter(struct slgt_info *info) 4083 { 4084 int i; 4085 for (i=0; i < info->port_count; ++i) { 4086 if (info->port_array[i]) 4087 reset_port(info->port_array[i]); 4088 } 4089 } 4090 4091 static void async_mode(struct slgt_info *info) 4092 { 4093 unsigned short val; 4094 4095 slgt_irq_off(info, IRQ_ALL | IRQ_MASTER); 4096 tx_stop(info); 4097 rx_stop(info); 4098 4099 /* TCR (tx control) 4100 * 4101 * 15..13 mode, 010=async 4102 * 12..10 encoding, 000=NRZ 4103 * 09 parity enable 4104 * 08 1=odd parity, 0=even parity 4105 * 07 1=RTS driver control 4106 * 06 1=break enable 4107 * 05..04 character length 4108 * 00=5 bits 4109 * 01=6 bits 4110 * 10=7 bits 4111 * 11=8 bits 4112 * 03 0=1 stop bit, 1=2 stop bits 4113 * 02 reset 4114 * 01 enable 4115 * 00 auto-CTS enable 4116 */ 4117 val = 0x4000; 4118 4119 if (info->if_mode & MGSL_INTERFACE_RTS_EN) 4120 val |= BIT7; 4121 4122 if (info->params.parity != ASYNC_PARITY_NONE) { 4123 val |= BIT9; 4124 if (info->params.parity == ASYNC_PARITY_ODD) 4125 val |= BIT8; 4126 } 4127 4128 switch (info->params.data_bits) 4129 { 4130 case 6: val |= BIT4; break; 4131 case 7: val |= BIT5; break; 4132 case 8: val |= BIT5 + BIT4; break; 4133 } 4134 4135 if (info->params.stop_bits != 1) 4136 val |= BIT3; 4137 4138 if (info->params.flags & HDLC_FLAG_AUTO_CTS) 4139 val |= BIT0; 4140 4141 wr_reg16(info, TCR, val); 4142 4143 /* RCR (rx control) 4144 * 4145 * 15..13 mode, 010=async 4146 * 12..10 encoding, 000=NRZ 4147 * 09 parity enable 4148 * 08 1=odd parity, 0=even parity 4149 * 07..06 reserved, must be 0 4150 * 05..04 character length 4151 * 00=5 bits 4152 * 01=6 bits 4153 * 10=7 bits 4154 * 11=8 bits 4155 * 03 reserved, must be zero 4156 * 02 reset 4157 * 01 enable 4158 * 00 auto-DCD enable 4159 */ 4160 val = 0x4000; 4161 4162 if (info->params.parity != ASYNC_PARITY_NONE) { 4163 val |= BIT9; 4164 if (info->params.parity == ASYNC_PARITY_ODD) 4165 val |= BIT8; 4166 } 4167 4168 switch (info->params.data_bits) 4169 { 4170 case 6: val |= BIT4; break; 4171 case 7: val |= BIT5; break; 4172 case 8: val |= BIT5 + BIT4; break; 4173 } 4174 4175 if (info->params.flags & HDLC_FLAG_AUTO_DCD) 4176 val |= BIT0; 4177 4178 wr_reg16(info, RCR, val); 4179 4180 /* CCR (clock control) 4181 * 4182 * 07..05 011 = tx clock source is BRG/16 4183 * 04..02 010 = rx clock source is BRG 4184 * 01 0 = auxclk disabled 4185 * 00 1 = BRG enabled 4186 * 4187 * 0110 1001 4188 */ 4189 wr_reg8(info, CCR, 0x69); 4190 4191 msc_set_vcr(info); 4192 4193 /* SCR (serial control) 4194 * 4195 * 15 1=tx req on FIFO half empty 4196 * 14 1=rx req on FIFO half full 4197 * 13 tx data IRQ enable 4198 * 12 tx idle IRQ enable 4199 * 11 rx break on IRQ enable 4200 * 10 rx data IRQ enable 4201 * 09 rx break off IRQ enable 4202 * 08 overrun IRQ enable 4203 * 07 DSR IRQ enable 4204 * 06 CTS IRQ enable 4205 * 05 DCD IRQ enable 4206 * 04 RI IRQ enable 4207 * 03 0=16x sampling, 1=8x sampling 4208 * 02 1=txd->rxd internal loopback enable 4209 * 01 reserved, must be zero 4210 * 00 1=master IRQ enable 4211 */ 4212 val = BIT15 + BIT14 + BIT0; 4213 /* JCR[8] : 1 = x8 async mode feature available */ 4214 if ((rd_reg32(info, JCR) & BIT8) && info->params.data_rate && 4215 ((info->base_clock < (info->params.data_rate * 16)) || 4216 (info->base_clock % (info->params.data_rate * 16)))) { 4217 /* use 8x sampling */ 4218 val |= BIT3; 4219 set_rate(info, info->params.data_rate * 8); 4220 } else { 4221 /* use 16x sampling */ 4222 set_rate(info, info->params.data_rate * 16); 4223 } 4224 wr_reg16(info, SCR, val); 4225 4226 slgt_irq_on(info, IRQ_RXBREAK | IRQ_RXOVER); 4227 4228 if (info->params.loopback) 4229 enable_loopback(info); 4230 } 4231 4232 static void sync_mode(struct slgt_info *info) 4233 { 4234 unsigned short val; 4235 4236 slgt_irq_off(info, IRQ_ALL | IRQ_MASTER); 4237 tx_stop(info); 4238 rx_stop(info); 4239 4240 /* TCR (tx control) 4241 * 4242 * 15..13 mode 4243 * 000=HDLC/SDLC 4244 * 001=raw bit synchronous 4245 * 010=asynchronous/isochronous 4246 * 011=monosync byte synchronous 4247 * 100=bisync byte synchronous 4248 * 101=xsync byte synchronous 4249 * 12..10 encoding 4250 * 09 CRC enable 4251 * 08 CRC32 4252 * 07 1=RTS driver control 4253 * 06 preamble enable 4254 * 05..04 preamble length 4255 * 03 share open/close flag 4256 * 02 reset 4257 * 01 enable 4258 * 00 auto-CTS enable 4259 */ 4260 val = BIT2; 4261 4262 switch(info->params.mode) { 4263 case MGSL_MODE_XSYNC: 4264 val |= BIT15 + BIT13; 4265 break; 4266 case MGSL_MODE_MONOSYNC: val |= BIT14 + BIT13; break; 4267 case MGSL_MODE_BISYNC: val |= BIT15; break; 4268 case MGSL_MODE_RAW: val |= BIT13; break; 4269 } 4270 if (info->if_mode & MGSL_INTERFACE_RTS_EN) 4271 val |= BIT7; 4272 4273 switch(info->params.encoding) 4274 { 4275 case HDLC_ENCODING_NRZB: val |= BIT10; break; 4276 case HDLC_ENCODING_NRZI_MARK: val |= BIT11; break; 4277 case HDLC_ENCODING_NRZI: val |= BIT11 + BIT10; break; 4278 case HDLC_ENCODING_BIPHASE_MARK: val |= BIT12; break; 4279 case HDLC_ENCODING_BIPHASE_SPACE: val |= BIT12 + BIT10; break; 4280 case HDLC_ENCODING_BIPHASE_LEVEL: val |= BIT12 + BIT11; break; 4281 case HDLC_ENCODING_DIFF_BIPHASE_LEVEL: val |= BIT12 + BIT11 + BIT10; break; 4282 } 4283 4284 switch (info->params.crc_type & HDLC_CRC_MASK) 4285 { 4286 case HDLC_CRC_16_CCITT: val |= BIT9; break; 4287 case HDLC_CRC_32_CCITT: val |= BIT9 + BIT8; break; 4288 } 4289 4290 if (info->params.preamble != HDLC_PREAMBLE_PATTERN_NONE) 4291 val |= BIT6; 4292 4293 switch (info->params.preamble_length) 4294 { 4295 case HDLC_PREAMBLE_LENGTH_16BITS: val |= BIT5; break; 4296 case HDLC_PREAMBLE_LENGTH_32BITS: val |= BIT4; break; 4297 case HDLC_PREAMBLE_LENGTH_64BITS: val |= BIT5 + BIT4; break; 4298 } 4299 4300 if (info->params.flags & HDLC_FLAG_AUTO_CTS) 4301 val |= BIT0; 4302 4303 wr_reg16(info, TCR, val); 4304 4305 /* TPR (transmit preamble) */ 4306 4307 switch (info->params.preamble) 4308 { 4309 case HDLC_PREAMBLE_PATTERN_FLAGS: val = 0x7e; break; 4310 case HDLC_PREAMBLE_PATTERN_ONES: val = 0xff; break; 4311 case HDLC_PREAMBLE_PATTERN_ZEROS: val = 0x00; break; 4312 case HDLC_PREAMBLE_PATTERN_10: val = 0x55; break; 4313 case HDLC_PREAMBLE_PATTERN_01: val = 0xaa; break; 4314 default: val = 0x7e; break; 4315 } 4316 wr_reg8(info, TPR, (unsigned char)val); 4317 4318 /* RCR (rx control) 4319 * 4320 * 15..13 mode 4321 * 000=HDLC/SDLC 4322 * 001=raw bit synchronous 4323 * 010=asynchronous/isochronous 4324 * 011=monosync byte synchronous 4325 * 100=bisync byte synchronous 4326 * 101=xsync byte synchronous 4327 * 12..10 encoding 4328 * 09 CRC enable 4329 * 08 CRC32 4330 * 07..03 reserved, must be 0 4331 * 02 reset 4332 * 01 enable 4333 * 00 auto-DCD enable 4334 */ 4335 val = 0; 4336 4337 switch(info->params.mode) { 4338 case MGSL_MODE_XSYNC: 4339 val |= BIT15 + BIT13; 4340 break; 4341 case MGSL_MODE_MONOSYNC: val |= BIT14 + BIT13; break; 4342 case MGSL_MODE_BISYNC: val |= BIT15; break; 4343 case MGSL_MODE_RAW: val |= BIT13; break; 4344 } 4345 4346 switch(info->params.encoding) 4347 { 4348 case HDLC_ENCODING_NRZB: val |= BIT10; break; 4349 case HDLC_ENCODING_NRZI_MARK: val |= BIT11; break; 4350 case HDLC_ENCODING_NRZI: val |= BIT11 + BIT10; break; 4351 case HDLC_ENCODING_BIPHASE_MARK: val |= BIT12; break; 4352 case HDLC_ENCODING_BIPHASE_SPACE: val |= BIT12 + BIT10; break; 4353 case HDLC_ENCODING_BIPHASE_LEVEL: val |= BIT12 + BIT11; break; 4354 case HDLC_ENCODING_DIFF_BIPHASE_LEVEL: val |= BIT12 + BIT11 + BIT10; break; 4355 } 4356 4357 switch (info->params.crc_type & HDLC_CRC_MASK) 4358 { 4359 case HDLC_CRC_16_CCITT: val |= BIT9; break; 4360 case HDLC_CRC_32_CCITT: val |= BIT9 + BIT8; break; 4361 } 4362 4363 if (info->params.flags & HDLC_FLAG_AUTO_DCD) 4364 val |= BIT0; 4365 4366 wr_reg16(info, RCR, val); 4367 4368 /* CCR (clock control) 4369 * 4370 * 07..05 tx clock source 4371 * 04..02 rx clock source 4372 * 01 auxclk enable 4373 * 00 BRG enable 4374 */ 4375 val = 0; 4376 4377 if (info->params.flags & HDLC_FLAG_TXC_BRG) 4378 { 4379 // when RxC source is DPLL, BRG generates 16X DPLL 4380 // reference clock, so take TxC from BRG/16 to get 4381 // transmit clock at actual data rate 4382 if (info->params.flags & HDLC_FLAG_RXC_DPLL) 4383 val |= BIT6 + BIT5; /* 011, txclk = BRG/16 */ 4384 else 4385 val |= BIT6; /* 010, txclk = BRG */ 4386 } 4387 else if (info->params.flags & HDLC_FLAG_TXC_DPLL) 4388 val |= BIT7; /* 100, txclk = DPLL Input */ 4389 else if (info->params.flags & HDLC_FLAG_TXC_RXCPIN) 4390 val |= BIT5; /* 001, txclk = RXC Input */ 4391 4392 if (info->params.flags & HDLC_FLAG_RXC_BRG) 4393 val |= BIT3; /* 010, rxclk = BRG */ 4394 else if (info->params.flags & HDLC_FLAG_RXC_DPLL) 4395 val |= BIT4; /* 100, rxclk = DPLL */ 4396 else if (info->params.flags & HDLC_FLAG_RXC_TXCPIN) 4397 val |= BIT2; /* 001, rxclk = TXC Input */ 4398 4399 if (info->params.clock_speed) 4400 val |= BIT1 + BIT0; 4401 4402 wr_reg8(info, CCR, (unsigned char)val); 4403 4404 if (info->params.flags & (HDLC_FLAG_TXC_DPLL + HDLC_FLAG_RXC_DPLL)) 4405 { 4406 // program DPLL mode 4407 switch(info->params.encoding) 4408 { 4409 case HDLC_ENCODING_BIPHASE_MARK: 4410 case HDLC_ENCODING_BIPHASE_SPACE: 4411 val = BIT7; break; 4412 case HDLC_ENCODING_BIPHASE_LEVEL: 4413 case HDLC_ENCODING_DIFF_BIPHASE_LEVEL: 4414 val = BIT7 + BIT6; break; 4415 default: val = BIT6; // NRZ encodings 4416 } 4417 wr_reg16(info, RCR, (unsigned short)(rd_reg16(info, RCR) | val)); 4418 4419 // DPLL requires a 16X reference clock from BRG 4420 set_rate(info, info->params.clock_speed * 16); 4421 } 4422 else 4423 set_rate(info, info->params.clock_speed); 4424 4425 tx_set_idle(info); 4426 4427 msc_set_vcr(info); 4428 4429 /* SCR (serial control) 4430 * 4431 * 15 1=tx req on FIFO half empty 4432 * 14 1=rx req on FIFO half full 4433 * 13 tx data IRQ enable 4434 * 12 tx idle IRQ enable 4435 * 11 underrun IRQ enable 4436 * 10 rx data IRQ enable 4437 * 09 rx idle IRQ enable 4438 * 08 overrun IRQ enable 4439 * 07 DSR IRQ enable 4440 * 06 CTS IRQ enable 4441 * 05 DCD IRQ enable 4442 * 04 RI IRQ enable 4443 * 03 reserved, must be zero 4444 * 02 1=txd->rxd internal loopback enable 4445 * 01 reserved, must be zero 4446 * 00 1=master IRQ enable 4447 */ 4448 wr_reg16(info, SCR, BIT15 + BIT14 + BIT0); 4449 4450 if (info->params.loopback) 4451 enable_loopback(info); 4452 } 4453 4454 /* 4455 * set transmit idle mode 4456 */ 4457 static void tx_set_idle(struct slgt_info *info) 4458 { 4459 unsigned char val; 4460 unsigned short tcr; 4461 4462 /* if preamble enabled (tcr[6] == 1) then tx idle size = 8 bits 4463 * else tcr[5:4] = tx idle size: 00 = 8 bits, 01 = 16 bits 4464 */ 4465 tcr = rd_reg16(info, TCR); 4466 if (info->idle_mode & HDLC_TXIDLE_CUSTOM_16) { 4467 /* disable preamble, set idle size to 16 bits */ 4468 tcr = (tcr & ~(BIT6 + BIT5)) | BIT4; 4469 /* MSB of 16 bit idle specified in tx preamble register (TPR) */ 4470 wr_reg8(info, TPR, (unsigned char)((info->idle_mode >> 8) & 0xff)); 4471 } else if (!(tcr & BIT6)) { 4472 /* preamble is disabled, set idle size to 8 bits */ 4473 tcr &= ~(BIT5 + BIT4); 4474 } 4475 wr_reg16(info, TCR, tcr); 4476 4477 if (info->idle_mode & (HDLC_TXIDLE_CUSTOM_8 | HDLC_TXIDLE_CUSTOM_16)) { 4478 /* LSB of custom tx idle specified in tx idle register */ 4479 val = (unsigned char)(info->idle_mode & 0xff); 4480 } else { 4481 /* standard 8 bit idle patterns */ 4482 switch(info->idle_mode) 4483 { 4484 case HDLC_TXIDLE_FLAGS: val = 0x7e; break; 4485 case HDLC_TXIDLE_ALT_ZEROS_ONES: 4486 case HDLC_TXIDLE_ALT_MARK_SPACE: val = 0xaa; break; 4487 case HDLC_TXIDLE_ZEROS: 4488 case HDLC_TXIDLE_SPACE: val = 0x00; break; 4489 default: val = 0xff; 4490 } 4491 } 4492 4493 wr_reg8(info, TIR, val); 4494 } 4495 4496 /* 4497 * get state of V24 status (input) signals 4498 */ 4499 static void get_signals(struct slgt_info *info) 4500 { 4501 unsigned short status = rd_reg16(info, SSR); 4502 4503 /* clear all serial signals except RTS and DTR */ 4504 info->signals &= SerialSignal_RTS | SerialSignal_DTR; 4505 4506 if (status & BIT3) 4507 info->signals |= SerialSignal_DSR; 4508 if (status & BIT2) 4509 info->signals |= SerialSignal_CTS; 4510 if (status & BIT1) 4511 info->signals |= SerialSignal_DCD; 4512 if (status & BIT0) 4513 info->signals |= SerialSignal_RI; 4514 } 4515 4516 /* 4517 * set V.24 Control Register based on current configuration 4518 */ 4519 static void msc_set_vcr(struct slgt_info *info) 4520 { 4521 unsigned char val = 0; 4522 4523 /* VCR (V.24 control) 4524 * 4525 * 07..04 serial IF select 4526 * 03 DTR 4527 * 02 RTS 4528 * 01 LL 4529 * 00 RL 4530 */ 4531 4532 switch(info->if_mode & MGSL_INTERFACE_MASK) 4533 { 4534 case MGSL_INTERFACE_RS232: 4535 val |= BIT5; /* 0010 */ 4536 break; 4537 case MGSL_INTERFACE_V35: 4538 val |= BIT7 + BIT6 + BIT5; /* 1110 */ 4539 break; 4540 case MGSL_INTERFACE_RS422: 4541 val |= BIT6; /* 0100 */ 4542 break; 4543 } 4544 4545 if (info->if_mode & MGSL_INTERFACE_MSB_FIRST) 4546 val |= BIT4; 4547 if (info->signals & SerialSignal_DTR) 4548 val |= BIT3; 4549 if (info->signals & SerialSignal_RTS) 4550 val |= BIT2; 4551 if (info->if_mode & MGSL_INTERFACE_LL) 4552 val |= BIT1; 4553 if (info->if_mode & MGSL_INTERFACE_RL) 4554 val |= BIT0; 4555 wr_reg8(info, VCR, val); 4556 } 4557 4558 /* 4559 * set state of V24 control (output) signals 4560 */ 4561 static void set_signals(struct slgt_info *info) 4562 { 4563 unsigned char val = rd_reg8(info, VCR); 4564 if (info->signals & SerialSignal_DTR) 4565 val |= BIT3; 4566 else 4567 val &= ~BIT3; 4568 if (info->signals & SerialSignal_RTS) 4569 val |= BIT2; 4570 else 4571 val &= ~BIT2; 4572 wr_reg8(info, VCR, val); 4573 } 4574 4575 /* 4576 * free range of receive DMA buffers (i to last) 4577 */ 4578 static void free_rbufs(struct slgt_info *info, unsigned int i, unsigned int last) 4579 { 4580 int done = 0; 4581 4582 while(!done) { 4583 /* reset current buffer for reuse */ 4584 info->rbufs[i].status = 0; 4585 set_desc_count(info->rbufs[i], info->rbuf_fill_level); 4586 if (i == last) 4587 done = 1; 4588 if (++i == info->rbuf_count) 4589 i = 0; 4590 } 4591 info->rbuf_current = i; 4592 } 4593 4594 /* 4595 * mark all receive DMA buffers as free 4596 */ 4597 static void reset_rbufs(struct slgt_info *info) 4598 { 4599 free_rbufs(info, 0, info->rbuf_count - 1); 4600 info->rbuf_fill_index = 0; 4601 info->rbuf_fill_count = 0; 4602 } 4603 4604 /* 4605 * pass receive HDLC frame to upper layer 4606 * 4607 * return true if frame available, otherwise false 4608 */ 4609 static bool rx_get_frame(struct slgt_info *info) 4610 { 4611 unsigned int start, end; 4612 unsigned short status; 4613 unsigned int framesize = 0; 4614 unsigned long flags; 4615 struct tty_struct *tty = info->port.tty; 4616 unsigned char addr_field = 0xff; 4617 unsigned int crc_size = 0; 4618 4619 switch (info->params.crc_type & HDLC_CRC_MASK) { 4620 case HDLC_CRC_16_CCITT: crc_size = 2; break; 4621 case HDLC_CRC_32_CCITT: crc_size = 4; break; 4622 } 4623 4624 check_again: 4625 4626 framesize = 0; 4627 addr_field = 0xff; 4628 start = end = info->rbuf_current; 4629 4630 for (;;) { 4631 if (!desc_complete(info->rbufs[end])) 4632 goto cleanup; 4633 4634 if (framesize == 0 && info->params.addr_filter != 0xff) 4635 addr_field = info->rbufs[end].buf[0]; 4636 4637 framesize += desc_count(info->rbufs[end]); 4638 4639 if (desc_eof(info->rbufs[end])) 4640 break; 4641 4642 if (++end == info->rbuf_count) 4643 end = 0; 4644 4645 if (end == info->rbuf_current) { 4646 if (info->rx_enabled){ 4647 spin_lock_irqsave(&info->lock,flags); 4648 rx_start(info); 4649 spin_unlock_irqrestore(&info->lock,flags); 4650 } 4651 goto cleanup; 4652 } 4653 } 4654 4655 /* status 4656 * 4657 * 15 buffer complete 4658 * 14..06 reserved 4659 * 05..04 residue 4660 * 02 eof (end of frame) 4661 * 01 CRC error 4662 * 00 abort 4663 */ 4664 status = desc_status(info->rbufs[end]); 4665 4666 /* ignore CRC bit if not using CRC (bit is undefined) */ 4667 if ((info->params.crc_type & HDLC_CRC_MASK) == HDLC_CRC_NONE) 4668 status &= ~BIT1; 4669 4670 if (framesize == 0 || 4671 (addr_field != 0xff && addr_field != info->params.addr_filter)) { 4672 free_rbufs(info, start, end); 4673 goto check_again; 4674 } 4675 4676 if (framesize < (2 + crc_size) || status & BIT0) { 4677 info->icount.rxshort++; 4678 framesize = 0; 4679 } else if (status & BIT1) { 4680 info->icount.rxcrc++; 4681 if (!(info->params.crc_type & HDLC_CRC_RETURN_EX)) 4682 framesize = 0; 4683 } 4684 4685 #if SYNCLINK_GENERIC_HDLC 4686 if (framesize == 0) { 4687 info->netdev->stats.rx_errors++; 4688 info->netdev->stats.rx_frame_errors++; 4689 } 4690 #endif 4691 4692 DBGBH(("%s rx frame status=%04X size=%d\n", 4693 info->device_name, status, framesize)); 4694 DBGDATA(info, info->rbufs[start].buf, min_t(int, framesize, info->rbuf_fill_level), "rx"); 4695 4696 if (framesize) { 4697 if (!(info->params.crc_type & HDLC_CRC_RETURN_EX)) { 4698 framesize -= crc_size; 4699 crc_size = 0; 4700 } 4701 4702 if (framesize > info->max_frame_size + crc_size) 4703 info->icount.rxlong++; 4704 else { 4705 /* copy dma buffer(s) to contiguous temp buffer */ 4706 int copy_count = framesize; 4707 int i = start; 4708 unsigned char *p = info->tmp_rbuf; 4709 info->tmp_rbuf_count = framesize; 4710 4711 info->icount.rxok++; 4712 4713 while(copy_count) { 4714 int partial_count = min_t(int, copy_count, info->rbuf_fill_level); 4715 memcpy(p, info->rbufs[i].buf, partial_count); 4716 p += partial_count; 4717 copy_count -= partial_count; 4718 if (++i == info->rbuf_count) 4719 i = 0; 4720 } 4721 4722 if (info->params.crc_type & HDLC_CRC_RETURN_EX) { 4723 *p = (status & BIT1) ? RX_CRC_ERROR : RX_OK; 4724 framesize++; 4725 } 4726 4727 #if SYNCLINK_GENERIC_HDLC 4728 if (info->netcount) 4729 hdlcdev_rx(info,info->tmp_rbuf, framesize); 4730 else 4731 #endif 4732 ldisc_receive_buf(tty, info->tmp_rbuf, info->flag_buf, framesize); 4733 } 4734 } 4735 free_rbufs(info, start, end); 4736 return true; 4737 4738 cleanup: 4739 return false; 4740 } 4741 4742 /* 4743 * pass receive buffer (RAW synchronous mode) to tty layer 4744 * return true if buffer available, otherwise false 4745 */ 4746 static bool rx_get_buf(struct slgt_info *info) 4747 { 4748 unsigned int i = info->rbuf_current; 4749 unsigned int count; 4750 4751 if (!desc_complete(info->rbufs[i])) 4752 return false; 4753 count = desc_count(info->rbufs[i]); 4754 switch(info->params.mode) { 4755 case MGSL_MODE_MONOSYNC: 4756 case MGSL_MODE_BISYNC: 4757 case MGSL_MODE_XSYNC: 4758 /* ignore residue in byte synchronous modes */ 4759 if (desc_residue(info->rbufs[i])) 4760 count--; 4761 break; 4762 } 4763 DBGDATA(info, info->rbufs[i].buf, count, "rx"); 4764 DBGINFO(("rx_get_buf size=%d\n", count)); 4765 if (count) 4766 ldisc_receive_buf(info->port.tty, info->rbufs[i].buf, 4767 info->flag_buf, count); 4768 free_rbufs(info, i, i); 4769 return true; 4770 } 4771 4772 static void reset_tbufs(struct slgt_info *info) 4773 { 4774 unsigned int i; 4775 info->tbuf_current = 0; 4776 for (i=0 ; i < info->tbuf_count ; i++) { 4777 info->tbufs[i].status = 0; 4778 info->tbufs[i].count = 0; 4779 } 4780 } 4781 4782 /* 4783 * return number of free transmit DMA buffers 4784 */ 4785 static unsigned int free_tbuf_count(struct slgt_info *info) 4786 { 4787 unsigned int count = 0; 4788 unsigned int i = info->tbuf_current; 4789 4790 do 4791 { 4792 if (desc_count(info->tbufs[i])) 4793 break; /* buffer in use */ 4794 ++count; 4795 if (++i == info->tbuf_count) 4796 i=0; 4797 } while (i != info->tbuf_current); 4798 4799 /* if tx DMA active, last zero count buffer is in use */ 4800 if (count && (rd_reg32(info, TDCSR) & BIT0)) 4801 --count; 4802 4803 return count; 4804 } 4805 4806 /* 4807 * return number of bytes in unsent transmit DMA buffers 4808 * and the serial controller tx FIFO 4809 */ 4810 static unsigned int tbuf_bytes(struct slgt_info *info) 4811 { 4812 unsigned int total_count = 0; 4813 unsigned int i = info->tbuf_current; 4814 unsigned int reg_value; 4815 unsigned int count; 4816 unsigned int active_buf_count = 0; 4817 4818 /* 4819 * Add descriptor counts for all tx DMA buffers. 4820 * If count is zero (cleared by DMA controller after read), 4821 * the buffer is complete or is actively being read from. 4822 * 4823 * Record buf_count of last buffer with zero count starting 4824 * from current ring position. buf_count is mirror 4825 * copy of count and is not cleared by serial controller. 4826 * If DMA controller is active, that buffer is actively 4827 * being read so add to total. 4828 */ 4829 do { 4830 count = desc_count(info->tbufs[i]); 4831 if (count) 4832 total_count += count; 4833 else if (!total_count) 4834 active_buf_count = info->tbufs[i].buf_count; 4835 if (++i == info->tbuf_count) 4836 i = 0; 4837 } while (i != info->tbuf_current); 4838 4839 /* read tx DMA status register */ 4840 reg_value = rd_reg32(info, TDCSR); 4841 4842 /* if tx DMA active, last zero count buffer is in use */ 4843 if (reg_value & BIT0) 4844 total_count += active_buf_count; 4845 4846 /* add tx FIFO count = reg_value[15..8] */ 4847 total_count += (reg_value >> 8) & 0xff; 4848 4849 /* if transmitter active add one byte for shift register */ 4850 if (info->tx_active) 4851 total_count++; 4852 4853 return total_count; 4854 } 4855 4856 /* 4857 * load data into transmit DMA buffer ring and start transmitter if needed 4858 * return true if data accepted, otherwise false (buffers full) 4859 */ 4860 static bool tx_load(struct slgt_info *info, const char *buf, unsigned int size) 4861 { 4862 unsigned short count; 4863 unsigned int i; 4864 struct slgt_desc *d; 4865 4866 /* check required buffer space */ 4867 if (DIV_ROUND_UP(size, DMABUFSIZE) > free_tbuf_count(info)) 4868 return false; 4869 4870 DBGDATA(info, buf, size, "tx"); 4871 4872 /* 4873 * copy data to one or more DMA buffers in circular ring 4874 * tbuf_start = first buffer for this data 4875 * tbuf_current = next free buffer 4876 * 4877 * Copy all data before making data visible to DMA controller by 4878 * setting descriptor count of the first buffer. 4879 * This prevents an active DMA controller from reading the first DMA 4880 * buffers of a frame and stopping before the final buffers are filled. 4881 */ 4882 4883 info->tbuf_start = i = info->tbuf_current; 4884 4885 while (size) { 4886 d = &info->tbufs[i]; 4887 4888 count = (unsigned short)((size > DMABUFSIZE) ? DMABUFSIZE : size); 4889 memcpy(d->buf, buf, count); 4890 4891 size -= count; 4892 buf += count; 4893 4894 /* 4895 * set EOF bit for last buffer of HDLC frame or 4896 * for every buffer in raw mode 4897 */ 4898 if ((!size && info->params.mode == MGSL_MODE_HDLC) || 4899 info->params.mode == MGSL_MODE_RAW) 4900 set_desc_eof(*d, 1); 4901 else 4902 set_desc_eof(*d, 0); 4903 4904 /* set descriptor count for all but first buffer */ 4905 if (i != info->tbuf_start) 4906 set_desc_count(*d, count); 4907 d->buf_count = count; 4908 4909 if (++i == info->tbuf_count) 4910 i = 0; 4911 } 4912 4913 info->tbuf_current = i; 4914 4915 /* set first buffer count to make new data visible to DMA controller */ 4916 d = &info->tbufs[info->tbuf_start]; 4917 set_desc_count(*d, d->buf_count); 4918 4919 /* start transmitter if needed and update transmit timeout */ 4920 if (!info->tx_active) 4921 tx_start(info); 4922 update_tx_timer(info); 4923 4924 return true; 4925 } 4926 4927 static int register_test(struct slgt_info *info) 4928 { 4929 static unsigned short patterns[] = 4930 {0x0000, 0xffff, 0xaaaa, 0x5555, 0x6969, 0x9696}; 4931 static unsigned int count = ARRAY_SIZE(patterns); 4932 unsigned int i; 4933 int rc = 0; 4934 4935 for (i=0 ; i < count ; i++) { 4936 wr_reg16(info, TIR, patterns[i]); 4937 wr_reg16(info, BDR, patterns[(i+1)%count]); 4938 if ((rd_reg16(info, TIR) != patterns[i]) || 4939 (rd_reg16(info, BDR) != patterns[(i+1)%count])) { 4940 rc = -ENODEV; 4941 break; 4942 } 4943 } 4944 info->gpio_present = (rd_reg32(info, JCR) & BIT5) ? 1 : 0; 4945 info->init_error = rc ? 0 : DiagStatus_AddressFailure; 4946 return rc; 4947 } 4948 4949 static int irq_test(struct slgt_info *info) 4950 { 4951 unsigned long timeout; 4952 unsigned long flags; 4953 struct tty_struct *oldtty = info->port.tty; 4954 u32 speed = info->params.data_rate; 4955 4956 info->params.data_rate = 921600; 4957 info->port.tty = NULL; 4958 4959 spin_lock_irqsave(&info->lock, flags); 4960 async_mode(info); 4961 slgt_irq_on(info, IRQ_TXIDLE); 4962 4963 /* enable transmitter */ 4964 wr_reg16(info, TCR, 4965 (unsigned short)(rd_reg16(info, TCR) | BIT1)); 4966 4967 /* write one byte and wait for tx idle */ 4968 wr_reg16(info, TDR, 0); 4969 4970 /* assume failure */ 4971 info->init_error = DiagStatus_IrqFailure; 4972 info->irq_occurred = false; 4973 4974 spin_unlock_irqrestore(&info->lock, flags); 4975 4976 timeout=100; 4977 while(timeout-- && !info->irq_occurred) 4978 msleep_interruptible(10); 4979 4980 spin_lock_irqsave(&info->lock,flags); 4981 reset_port(info); 4982 spin_unlock_irqrestore(&info->lock,flags); 4983 4984 info->params.data_rate = speed; 4985 info->port.tty = oldtty; 4986 4987 info->init_error = info->irq_occurred ? 0 : DiagStatus_IrqFailure; 4988 return info->irq_occurred ? 0 : -ENODEV; 4989 } 4990 4991 static int loopback_test_rx(struct slgt_info *info) 4992 { 4993 unsigned char *src, *dest; 4994 int count; 4995 4996 if (desc_complete(info->rbufs[0])) { 4997 count = desc_count(info->rbufs[0]); 4998 src = info->rbufs[0].buf; 4999 dest = info->tmp_rbuf; 5000 5001 for( ; count ; count-=2, src+=2) { 5002 /* src=data byte (src+1)=status byte */ 5003 if (!(*(src+1) & (BIT9 + BIT8))) { 5004 *dest = *src; 5005 dest++; 5006 info->tmp_rbuf_count++; 5007 } 5008 } 5009 DBGDATA(info, info->tmp_rbuf, info->tmp_rbuf_count, "rx"); 5010 return 1; 5011 } 5012 return 0; 5013 } 5014 5015 static int loopback_test(struct slgt_info *info) 5016 { 5017 #define TESTFRAMESIZE 20 5018 5019 unsigned long timeout; 5020 u16 count = TESTFRAMESIZE; 5021 unsigned char buf[TESTFRAMESIZE]; 5022 int rc = -ENODEV; 5023 unsigned long flags; 5024 5025 struct tty_struct *oldtty = info->port.tty; 5026 MGSL_PARAMS params; 5027 5028 memcpy(¶ms, &info->params, sizeof(params)); 5029 5030 info->params.mode = MGSL_MODE_ASYNC; 5031 info->params.data_rate = 921600; 5032 info->params.loopback = 1; 5033 info->port.tty = NULL; 5034 5035 /* build and send transmit frame */ 5036 for (count = 0; count < TESTFRAMESIZE; ++count) 5037 buf[count] = (unsigned char)count; 5038 5039 info->tmp_rbuf_count = 0; 5040 memset(info->tmp_rbuf, 0, TESTFRAMESIZE); 5041 5042 /* program hardware for HDLC and enabled receiver */ 5043 spin_lock_irqsave(&info->lock,flags); 5044 async_mode(info); 5045 rx_start(info); 5046 tx_load(info, buf, count); 5047 spin_unlock_irqrestore(&info->lock, flags); 5048 5049 /* wait for receive complete */ 5050 for (timeout = 100; timeout; --timeout) { 5051 msleep_interruptible(10); 5052 if (loopback_test_rx(info)) { 5053 rc = 0; 5054 break; 5055 } 5056 } 5057 5058 /* verify received frame length and contents */ 5059 if (!rc && (info->tmp_rbuf_count != count || 5060 memcmp(buf, info->tmp_rbuf, count))) { 5061 rc = -ENODEV; 5062 } 5063 5064 spin_lock_irqsave(&info->lock,flags); 5065 reset_adapter(info); 5066 spin_unlock_irqrestore(&info->lock,flags); 5067 5068 memcpy(&info->params, ¶ms, sizeof(info->params)); 5069 info->port.tty = oldtty; 5070 5071 info->init_error = rc ? DiagStatus_DmaFailure : 0; 5072 return rc; 5073 } 5074 5075 static int adapter_test(struct slgt_info *info) 5076 { 5077 DBGINFO(("testing %s\n", info->device_name)); 5078 if (register_test(info) < 0) { 5079 printk("register test failure %s addr=%08X\n", 5080 info->device_name, info->phys_reg_addr); 5081 } else if (irq_test(info) < 0) { 5082 printk("IRQ test failure %s IRQ=%d\n", 5083 info->device_name, info->irq_level); 5084 } else if (loopback_test(info) < 0) { 5085 printk("loopback test failure %s\n", info->device_name); 5086 } 5087 return info->init_error; 5088 } 5089 5090 /* 5091 * transmit timeout handler 5092 */ 5093 static void tx_timeout(struct timer_list *t) 5094 { 5095 struct slgt_info *info = from_timer(info, t, tx_timer); 5096 unsigned long flags; 5097 5098 DBGINFO(("%s tx_timeout\n", info->device_name)); 5099 if(info->tx_active && info->params.mode == MGSL_MODE_HDLC) { 5100 info->icount.txtimeout++; 5101 } 5102 spin_lock_irqsave(&info->lock,flags); 5103 tx_stop(info); 5104 spin_unlock_irqrestore(&info->lock,flags); 5105 5106 #if SYNCLINK_GENERIC_HDLC 5107 if (info->netcount) 5108 hdlcdev_tx_done(info); 5109 else 5110 #endif 5111 bh_transmit(info); 5112 } 5113 5114 /* 5115 * receive buffer polling timer 5116 */ 5117 static void rx_timeout(struct timer_list *t) 5118 { 5119 struct slgt_info *info = from_timer(info, t, rx_timer); 5120 unsigned long flags; 5121 5122 DBGINFO(("%s rx_timeout\n", info->device_name)); 5123 spin_lock_irqsave(&info->lock, flags); 5124 info->pending_bh |= BH_RECEIVE; 5125 spin_unlock_irqrestore(&info->lock, flags); 5126 bh_handler(&info->task); 5127 } 5128 5129