xref: /openbmc/linux/drivers/tty/synclink_gt.c (revision a06c488d)
1 /*
2  * Device driver for Microgate SyncLink GT serial adapters.
3  *
4  * written by Paul Fulghum for Microgate Corporation
5  * paulkf@microgate.com
6  *
7  * Microgate and SyncLink are trademarks of Microgate Corporation
8  *
9  * This code is released under the GNU General Public License (GPL)
10  *
11  * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
12  * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
13  * OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
14  * DISCLAIMED.  IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT,
15  * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
16  * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
17  * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
18  * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
19  * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
20  * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED
21  * OF THE POSSIBILITY OF SUCH DAMAGE.
22  */
23 
24 /*
25  * DEBUG OUTPUT DEFINITIONS
26  *
27  * uncomment lines below to enable specific types of debug output
28  *
29  * DBGINFO   information - most verbose output
30  * DBGERR    serious errors
31  * DBGBH     bottom half service routine debugging
32  * DBGISR    interrupt service routine debugging
33  * DBGDATA   output receive and transmit data
34  * DBGTBUF   output transmit DMA buffers and registers
35  * DBGRBUF   output receive DMA buffers and registers
36  */
37 
38 #define DBGINFO(fmt) if (debug_level >= DEBUG_LEVEL_INFO) printk fmt
39 #define DBGERR(fmt) if (debug_level >= DEBUG_LEVEL_ERROR) printk fmt
40 #define DBGBH(fmt) if (debug_level >= DEBUG_LEVEL_BH) printk fmt
41 #define DBGISR(fmt) if (debug_level >= DEBUG_LEVEL_ISR) printk fmt
42 #define DBGDATA(info, buf, size, label) if (debug_level >= DEBUG_LEVEL_DATA) trace_block((info), (buf), (size), (label))
43 /*#define DBGTBUF(info) dump_tbufs(info)*/
44 /*#define DBGRBUF(info) dump_rbufs(info)*/
45 
46 
47 #include <linux/module.h>
48 #include <linux/errno.h>
49 #include <linux/signal.h>
50 #include <linux/sched.h>
51 #include <linux/timer.h>
52 #include <linux/interrupt.h>
53 #include <linux/pci.h>
54 #include <linux/tty.h>
55 #include <linux/tty_flip.h>
56 #include <linux/serial.h>
57 #include <linux/major.h>
58 #include <linux/string.h>
59 #include <linux/fcntl.h>
60 #include <linux/ptrace.h>
61 #include <linux/ioport.h>
62 #include <linux/mm.h>
63 #include <linux/seq_file.h>
64 #include <linux/slab.h>
65 #include <linux/netdevice.h>
66 #include <linux/vmalloc.h>
67 #include <linux/init.h>
68 #include <linux/delay.h>
69 #include <linux/ioctl.h>
70 #include <linux/termios.h>
71 #include <linux/bitops.h>
72 #include <linux/workqueue.h>
73 #include <linux/hdlc.h>
74 #include <linux/synclink.h>
75 
76 #include <asm/io.h>
77 #include <asm/irq.h>
78 #include <asm/dma.h>
79 #include <asm/types.h>
80 #include <asm/uaccess.h>
81 
82 #if defined(CONFIG_HDLC) || (defined(CONFIG_HDLC_MODULE) && defined(CONFIG_SYNCLINK_GT_MODULE))
83 #define SYNCLINK_GENERIC_HDLC 1
84 #else
85 #define SYNCLINK_GENERIC_HDLC 0
86 #endif
87 
88 /*
89  * module identification
90  */
91 static char *driver_name     = "SyncLink GT";
92 static char *slgt_driver_name = "synclink_gt";
93 static char *tty_dev_prefix  = "ttySLG";
94 MODULE_LICENSE("GPL");
95 #define MGSL_MAGIC 0x5401
96 #define MAX_DEVICES 32
97 
98 static struct pci_device_id pci_table[] = {
99 	{PCI_VENDOR_ID_MICROGATE, SYNCLINK_GT_DEVICE_ID, PCI_ANY_ID, PCI_ANY_ID,},
100 	{PCI_VENDOR_ID_MICROGATE, SYNCLINK_GT2_DEVICE_ID, PCI_ANY_ID, PCI_ANY_ID,},
101 	{PCI_VENDOR_ID_MICROGATE, SYNCLINK_GT4_DEVICE_ID, PCI_ANY_ID, PCI_ANY_ID,},
102 	{PCI_VENDOR_ID_MICROGATE, SYNCLINK_AC_DEVICE_ID, PCI_ANY_ID, PCI_ANY_ID,},
103 	{0,}, /* terminate list */
104 };
105 MODULE_DEVICE_TABLE(pci, pci_table);
106 
107 static int  init_one(struct pci_dev *dev,const struct pci_device_id *ent);
108 static void remove_one(struct pci_dev *dev);
109 static struct pci_driver pci_driver = {
110 	.name		= "synclink_gt",
111 	.id_table	= pci_table,
112 	.probe		= init_one,
113 	.remove		= remove_one,
114 };
115 
116 static bool pci_registered;
117 
118 /*
119  * module configuration and status
120  */
121 static struct slgt_info *slgt_device_list;
122 static int slgt_device_count;
123 
124 static int ttymajor;
125 static int debug_level;
126 static int maxframe[MAX_DEVICES];
127 
128 module_param(ttymajor, int, 0);
129 module_param(debug_level, int, 0);
130 module_param_array(maxframe, int, NULL, 0);
131 
132 MODULE_PARM_DESC(ttymajor, "TTY major device number override: 0=auto assigned");
133 MODULE_PARM_DESC(debug_level, "Debug syslog output: 0=disabled, 1 to 5=increasing detail");
134 MODULE_PARM_DESC(maxframe, "Maximum frame size used by device (4096 to 65535)");
135 
136 /*
137  * tty support and callbacks
138  */
139 static struct tty_driver *serial_driver;
140 
141 static int  open(struct tty_struct *tty, struct file * filp);
142 static void close(struct tty_struct *tty, struct file * filp);
143 static void hangup(struct tty_struct *tty);
144 static void set_termios(struct tty_struct *tty, struct ktermios *old_termios);
145 
146 static int  write(struct tty_struct *tty, const unsigned char *buf, int count);
147 static int put_char(struct tty_struct *tty, unsigned char ch);
148 static void send_xchar(struct tty_struct *tty, char ch);
149 static void wait_until_sent(struct tty_struct *tty, int timeout);
150 static int  write_room(struct tty_struct *tty);
151 static void flush_chars(struct tty_struct *tty);
152 static void flush_buffer(struct tty_struct *tty);
153 static void tx_hold(struct tty_struct *tty);
154 static void tx_release(struct tty_struct *tty);
155 
156 static int  ioctl(struct tty_struct *tty, unsigned int cmd, unsigned long arg);
157 static int  chars_in_buffer(struct tty_struct *tty);
158 static void throttle(struct tty_struct * tty);
159 static void unthrottle(struct tty_struct * tty);
160 static int set_break(struct tty_struct *tty, int break_state);
161 
162 /*
163  * generic HDLC support and callbacks
164  */
165 #if SYNCLINK_GENERIC_HDLC
166 #define dev_to_port(D) (dev_to_hdlc(D)->priv)
167 static void hdlcdev_tx_done(struct slgt_info *info);
168 static void hdlcdev_rx(struct slgt_info *info, char *buf, int size);
169 static int  hdlcdev_init(struct slgt_info *info);
170 static void hdlcdev_exit(struct slgt_info *info);
171 #endif
172 
173 
174 /*
175  * device specific structures, macros and functions
176  */
177 
178 #define SLGT_MAX_PORTS 4
179 #define SLGT_REG_SIZE  256
180 
181 /*
182  * conditional wait facility
183  */
184 struct cond_wait {
185 	struct cond_wait *next;
186 	wait_queue_head_t q;
187 	wait_queue_t wait;
188 	unsigned int data;
189 };
190 static void init_cond_wait(struct cond_wait *w, unsigned int data);
191 static void add_cond_wait(struct cond_wait **head, struct cond_wait *w);
192 static void remove_cond_wait(struct cond_wait **head, struct cond_wait *w);
193 static void flush_cond_wait(struct cond_wait **head);
194 
195 /*
196  * DMA buffer descriptor and access macros
197  */
198 struct slgt_desc
199 {
200 	__le16 count;
201 	__le16 status;
202 	__le32 pbuf;  /* physical address of data buffer */
203 	__le32 next;  /* physical address of next descriptor */
204 
205 	/* driver book keeping */
206 	char *buf;          /* virtual  address of data buffer */
207     	unsigned int pdesc; /* physical address of this descriptor */
208 	dma_addr_t buf_dma_addr;
209 	unsigned short buf_count;
210 };
211 
212 #define set_desc_buffer(a,b) (a).pbuf = cpu_to_le32((unsigned int)(b))
213 #define set_desc_next(a,b) (a).next   = cpu_to_le32((unsigned int)(b))
214 #define set_desc_count(a,b)(a).count  = cpu_to_le16((unsigned short)(b))
215 #define set_desc_eof(a,b)  (a).status = cpu_to_le16((b) ? (le16_to_cpu((a).status) | BIT0) : (le16_to_cpu((a).status) & ~BIT0))
216 #define set_desc_status(a, b) (a).status = cpu_to_le16((unsigned short)(b))
217 #define desc_count(a)      (le16_to_cpu((a).count))
218 #define desc_status(a)     (le16_to_cpu((a).status))
219 #define desc_complete(a)   (le16_to_cpu((a).status) & BIT15)
220 #define desc_eof(a)        (le16_to_cpu((a).status) & BIT2)
221 #define desc_crc_error(a)  (le16_to_cpu((a).status) & BIT1)
222 #define desc_abort(a)      (le16_to_cpu((a).status) & BIT0)
223 #define desc_residue(a)    ((le16_to_cpu((a).status) & 0x38) >> 3)
224 
225 struct _input_signal_events {
226 	int ri_up;
227 	int ri_down;
228 	int dsr_up;
229 	int dsr_down;
230 	int dcd_up;
231 	int dcd_down;
232 	int cts_up;
233 	int cts_down;
234 };
235 
236 /*
237  * device instance data structure
238  */
239 struct slgt_info {
240 	void *if_ptr;		/* General purpose pointer (used by SPPP) */
241 	struct tty_port port;
242 
243 	struct slgt_info *next_device;	/* device list link */
244 
245 	int magic;
246 
247 	char device_name[25];
248 	struct pci_dev *pdev;
249 
250 	int port_count;  /* count of ports on adapter */
251 	int adapter_num; /* adapter instance number */
252 	int port_num;    /* port instance number */
253 
254 	/* array of pointers to port contexts on this adapter */
255 	struct slgt_info *port_array[SLGT_MAX_PORTS];
256 
257 	int			line;		/* tty line instance number */
258 
259 	struct mgsl_icount	icount;
260 
261 	int			timeout;
262 	int			x_char;		/* xon/xoff character */
263 	unsigned int		read_status_mask;
264 	unsigned int 		ignore_status_mask;
265 
266 	wait_queue_head_t	status_event_wait_q;
267 	wait_queue_head_t	event_wait_q;
268 	struct timer_list	tx_timer;
269 	struct timer_list	rx_timer;
270 
271 	unsigned int            gpio_present;
272 	struct cond_wait        *gpio_wait_q;
273 
274 	spinlock_t lock;	/* spinlock for synchronizing with ISR */
275 
276 	struct work_struct task;
277 	u32 pending_bh;
278 	bool bh_requested;
279 	bool bh_running;
280 
281 	int isr_overflow;
282 	bool irq_requested;	/* true if IRQ requested */
283 	bool irq_occurred;	/* for diagnostics use */
284 
285 	/* device configuration */
286 
287 	unsigned int bus_type;
288 	unsigned int irq_level;
289 	unsigned long irq_flags;
290 
291 	unsigned char __iomem * reg_addr;  /* memory mapped registers address */
292 	u32 phys_reg_addr;
293 	bool reg_addr_requested;
294 
295 	MGSL_PARAMS params;       /* communications parameters */
296 	u32 idle_mode;
297 	u32 max_frame_size;       /* as set by device config */
298 
299 	unsigned int rbuf_fill_level;
300 	unsigned int rx_pio;
301 	unsigned int if_mode;
302 	unsigned int base_clock;
303 	unsigned int xsync;
304 	unsigned int xctrl;
305 
306 	/* device status */
307 
308 	bool rx_enabled;
309 	bool rx_restart;
310 
311 	bool tx_enabled;
312 	bool tx_active;
313 
314 	unsigned char signals;    /* serial signal states */
315 	int init_error;  /* initialization error */
316 
317 	unsigned char *tx_buf;
318 	int tx_count;
319 
320 	char *flag_buf;
321 	bool drop_rts_on_tx_done;
322 	struct	_input_signal_events	input_signal_events;
323 
324 	int dcd_chkcount;	/* check counts to prevent */
325 	int cts_chkcount;	/* too many IRQs if a signal */
326 	int dsr_chkcount;	/* is floating */
327 	int ri_chkcount;
328 
329 	char *bufs;		/* virtual address of DMA buffer lists */
330 	dma_addr_t bufs_dma_addr; /* physical address of buffer descriptors */
331 
332 	unsigned int rbuf_count;
333 	struct slgt_desc *rbufs;
334 	unsigned int rbuf_current;
335 	unsigned int rbuf_index;
336 	unsigned int rbuf_fill_index;
337 	unsigned short rbuf_fill_count;
338 
339 	unsigned int tbuf_count;
340 	struct slgt_desc *tbufs;
341 	unsigned int tbuf_current;
342 	unsigned int tbuf_start;
343 
344 	unsigned char *tmp_rbuf;
345 	unsigned int tmp_rbuf_count;
346 
347 	/* SPPP/Cisco HDLC device parts */
348 
349 	int netcount;
350 	spinlock_t netlock;
351 #if SYNCLINK_GENERIC_HDLC
352 	struct net_device *netdev;
353 #endif
354 
355 };
356 
357 static MGSL_PARAMS default_params = {
358 	.mode            = MGSL_MODE_HDLC,
359 	.loopback        = 0,
360 	.flags           = HDLC_FLAG_UNDERRUN_ABORT15,
361 	.encoding        = HDLC_ENCODING_NRZI_SPACE,
362 	.clock_speed     = 0,
363 	.addr_filter     = 0xff,
364 	.crc_type        = HDLC_CRC_16_CCITT,
365 	.preamble_length = HDLC_PREAMBLE_LENGTH_8BITS,
366 	.preamble        = HDLC_PREAMBLE_PATTERN_NONE,
367 	.data_rate       = 9600,
368 	.data_bits       = 8,
369 	.stop_bits       = 1,
370 	.parity          = ASYNC_PARITY_NONE
371 };
372 
373 
374 #define BH_RECEIVE  1
375 #define BH_TRANSMIT 2
376 #define BH_STATUS   4
377 #define IO_PIN_SHUTDOWN_LIMIT 100
378 
379 #define DMABUFSIZE 256
380 #define DESC_LIST_SIZE 4096
381 
382 #define MASK_PARITY  BIT1
383 #define MASK_FRAMING BIT0
384 #define MASK_BREAK   BIT14
385 #define MASK_OVERRUN BIT4
386 
387 #define GSR   0x00 /* global status */
388 #define JCR   0x04 /* JTAG control */
389 #define IODR  0x08 /* GPIO direction */
390 #define IOER  0x0c /* GPIO interrupt enable */
391 #define IOVR  0x10 /* GPIO value */
392 #define IOSR  0x14 /* GPIO interrupt status */
393 #define TDR   0x80 /* tx data */
394 #define RDR   0x80 /* rx data */
395 #define TCR   0x82 /* tx control */
396 #define TIR   0x84 /* tx idle */
397 #define TPR   0x85 /* tx preamble */
398 #define RCR   0x86 /* rx control */
399 #define VCR   0x88 /* V.24 control */
400 #define CCR   0x89 /* clock control */
401 #define BDR   0x8a /* baud divisor */
402 #define SCR   0x8c /* serial control */
403 #define SSR   0x8e /* serial status */
404 #define RDCSR 0x90 /* rx DMA control/status */
405 #define TDCSR 0x94 /* tx DMA control/status */
406 #define RDDAR 0x98 /* rx DMA descriptor address */
407 #define TDDAR 0x9c /* tx DMA descriptor address */
408 #define XSR   0x40 /* extended sync pattern */
409 #define XCR   0x44 /* extended control */
410 
411 #define RXIDLE      BIT14
412 #define RXBREAK     BIT14
413 #define IRQ_TXDATA  BIT13
414 #define IRQ_TXIDLE  BIT12
415 #define IRQ_TXUNDER BIT11 /* HDLC */
416 #define IRQ_RXDATA  BIT10
417 #define IRQ_RXIDLE  BIT9  /* HDLC */
418 #define IRQ_RXBREAK BIT9  /* async */
419 #define IRQ_RXOVER  BIT8
420 #define IRQ_DSR     BIT7
421 #define IRQ_CTS     BIT6
422 #define IRQ_DCD     BIT5
423 #define IRQ_RI      BIT4
424 #define IRQ_ALL     0x3ff0
425 #define IRQ_MASTER  BIT0
426 
427 #define slgt_irq_on(info, mask) \
428 	wr_reg16((info), SCR, (unsigned short)(rd_reg16((info), SCR) | (mask)))
429 #define slgt_irq_off(info, mask) \
430 	wr_reg16((info), SCR, (unsigned short)(rd_reg16((info), SCR) & ~(mask)))
431 
432 static __u8  rd_reg8(struct slgt_info *info, unsigned int addr);
433 static void  wr_reg8(struct slgt_info *info, unsigned int addr, __u8 value);
434 static __u16 rd_reg16(struct slgt_info *info, unsigned int addr);
435 static void  wr_reg16(struct slgt_info *info, unsigned int addr, __u16 value);
436 static __u32 rd_reg32(struct slgt_info *info, unsigned int addr);
437 static void  wr_reg32(struct slgt_info *info, unsigned int addr, __u32 value);
438 
439 static void  msc_set_vcr(struct slgt_info *info);
440 
441 static int  startup(struct slgt_info *info);
442 static int  block_til_ready(struct tty_struct *tty, struct file * filp,struct slgt_info *info);
443 static void shutdown(struct slgt_info *info);
444 static void program_hw(struct slgt_info *info);
445 static void change_params(struct slgt_info *info);
446 
447 static int  register_test(struct slgt_info *info);
448 static int  irq_test(struct slgt_info *info);
449 static int  loopback_test(struct slgt_info *info);
450 static int  adapter_test(struct slgt_info *info);
451 
452 static void reset_adapter(struct slgt_info *info);
453 static void reset_port(struct slgt_info *info);
454 static void async_mode(struct slgt_info *info);
455 static void sync_mode(struct slgt_info *info);
456 
457 static void rx_stop(struct slgt_info *info);
458 static void rx_start(struct slgt_info *info);
459 static void reset_rbufs(struct slgt_info *info);
460 static void free_rbufs(struct slgt_info *info, unsigned int first, unsigned int last);
461 static void rdma_reset(struct slgt_info *info);
462 static bool rx_get_frame(struct slgt_info *info);
463 static bool rx_get_buf(struct slgt_info *info);
464 
465 static void tx_start(struct slgt_info *info);
466 static void tx_stop(struct slgt_info *info);
467 static void tx_set_idle(struct slgt_info *info);
468 static unsigned int free_tbuf_count(struct slgt_info *info);
469 static unsigned int tbuf_bytes(struct slgt_info *info);
470 static void reset_tbufs(struct slgt_info *info);
471 static void tdma_reset(struct slgt_info *info);
472 static bool tx_load(struct slgt_info *info, const char *buf, unsigned int count);
473 
474 static void get_signals(struct slgt_info *info);
475 static void set_signals(struct slgt_info *info);
476 static void enable_loopback(struct slgt_info *info);
477 static void set_rate(struct slgt_info *info, u32 data_rate);
478 
479 static int  bh_action(struct slgt_info *info);
480 static void bh_handler(struct work_struct *work);
481 static void bh_transmit(struct slgt_info *info);
482 static void isr_serial(struct slgt_info *info);
483 static void isr_rdma(struct slgt_info *info);
484 static void isr_txeom(struct slgt_info *info, unsigned short status);
485 static void isr_tdma(struct slgt_info *info);
486 
487 static int  alloc_dma_bufs(struct slgt_info *info);
488 static void free_dma_bufs(struct slgt_info *info);
489 static int  alloc_desc(struct slgt_info *info);
490 static void free_desc(struct slgt_info *info);
491 static int  alloc_bufs(struct slgt_info *info, struct slgt_desc *bufs, int count);
492 static void free_bufs(struct slgt_info *info, struct slgt_desc *bufs, int count);
493 
494 static int  alloc_tmp_rbuf(struct slgt_info *info);
495 static void free_tmp_rbuf(struct slgt_info *info);
496 
497 static void tx_timeout(unsigned long context);
498 static void rx_timeout(unsigned long context);
499 
500 /*
501  * ioctl handlers
502  */
503 static int  get_stats(struct slgt_info *info, struct mgsl_icount __user *user_icount);
504 static int  get_params(struct slgt_info *info, MGSL_PARAMS __user *params);
505 static int  set_params(struct slgt_info *info, MGSL_PARAMS __user *params);
506 static int  get_txidle(struct slgt_info *info, int __user *idle_mode);
507 static int  set_txidle(struct slgt_info *info, int idle_mode);
508 static int  tx_enable(struct slgt_info *info, int enable);
509 static int  tx_abort(struct slgt_info *info);
510 static int  rx_enable(struct slgt_info *info, int enable);
511 static int  modem_input_wait(struct slgt_info *info,int arg);
512 static int  wait_mgsl_event(struct slgt_info *info, int __user *mask_ptr);
513 static int  tiocmget(struct tty_struct *tty);
514 static int  tiocmset(struct tty_struct *tty,
515 				unsigned int set, unsigned int clear);
516 static int set_break(struct tty_struct *tty, int break_state);
517 static int  get_interface(struct slgt_info *info, int __user *if_mode);
518 static int  set_interface(struct slgt_info *info, int if_mode);
519 static int  set_gpio(struct slgt_info *info, struct gpio_desc __user *gpio);
520 static int  get_gpio(struct slgt_info *info, struct gpio_desc __user *gpio);
521 static int  wait_gpio(struct slgt_info *info, struct gpio_desc __user *gpio);
522 static int  get_xsync(struct slgt_info *info, int __user *if_mode);
523 static int  set_xsync(struct slgt_info *info, int if_mode);
524 static int  get_xctrl(struct slgt_info *info, int __user *if_mode);
525 static int  set_xctrl(struct slgt_info *info, int if_mode);
526 
527 /*
528  * driver functions
529  */
530 static void add_device(struct slgt_info *info);
531 static void device_init(int adapter_num, struct pci_dev *pdev);
532 static int  claim_resources(struct slgt_info *info);
533 static void release_resources(struct slgt_info *info);
534 
535 /*
536  * DEBUG OUTPUT CODE
537  */
538 #ifndef DBGINFO
539 #define DBGINFO(fmt)
540 #endif
541 #ifndef DBGERR
542 #define DBGERR(fmt)
543 #endif
544 #ifndef DBGBH
545 #define DBGBH(fmt)
546 #endif
547 #ifndef DBGISR
548 #define DBGISR(fmt)
549 #endif
550 
551 #ifdef DBGDATA
552 static void trace_block(struct slgt_info *info, const char *data, int count, const char *label)
553 {
554 	int i;
555 	int linecount;
556 	printk("%s %s data:\n",info->device_name, label);
557 	while(count) {
558 		linecount = (count > 16) ? 16 : count;
559 		for(i=0; i < linecount; i++)
560 			printk("%02X ",(unsigned char)data[i]);
561 		for(;i<17;i++)
562 			printk("   ");
563 		for(i=0;i<linecount;i++) {
564 			if (data[i]>=040 && data[i]<=0176)
565 				printk("%c",data[i]);
566 			else
567 				printk(".");
568 		}
569 		printk("\n");
570 		data  += linecount;
571 		count -= linecount;
572 	}
573 }
574 #else
575 #define DBGDATA(info, buf, size, label)
576 #endif
577 
578 #ifdef DBGTBUF
579 static void dump_tbufs(struct slgt_info *info)
580 {
581 	int i;
582 	printk("tbuf_current=%d\n", info->tbuf_current);
583 	for (i=0 ; i < info->tbuf_count ; i++) {
584 		printk("%d: count=%04X status=%04X\n",
585 			i, le16_to_cpu(info->tbufs[i].count), le16_to_cpu(info->tbufs[i].status));
586 	}
587 }
588 #else
589 #define DBGTBUF(info)
590 #endif
591 
592 #ifdef DBGRBUF
593 static void dump_rbufs(struct slgt_info *info)
594 {
595 	int i;
596 	printk("rbuf_current=%d\n", info->rbuf_current);
597 	for (i=0 ; i < info->rbuf_count ; i++) {
598 		printk("%d: count=%04X status=%04X\n",
599 			i, le16_to_cpu(info->rbufs[i].count), le16_to_cpu(info->rbufs[i].status));
600 	}
601 }
602 #else
603 #define DBGRBUF(info)
604 #endif
605 
606 static inline int sanity_check(struct slgt_info *info, char *devname, const char *name)
607 {
608 #ifdef SANITY_CHECK
609 	if (!info) {
610 		printk("null struct slgt_info for (%s) in %s\n", devname, name);
611 		return 1;
612 	}
613 	if (info->magic != MGSL_MAGIC) {
614 		printk("bad magic number struct slgt_info (%s) in %s\n", devname, name);
615 		return 1;
616 	}
617 #else
618 	if (!info)
619 		return 1;
620 #endif
621 	return 0;
622 }
623 
624 /**
625  * line discipline callback wrappers
626  *
627  * The wrappers maintain line discipline references
628  * while calling into the line discipline.
629  *
630  * ldisc_receive_buf  - pass receive data to line discipline
631  */
632 static void ldisc_receive_buf(struct tty_struct *tty,
633 			      const __u8 *data, char *flags, int count)
634 {
635 	struct tty_ldisc *ld;
636 	if (!tty)
637 		return;
638 	ld = tty_ldisc_ref(tty);
639 	if (ld) {
640 		if (ld->ops->receive_buf)
641 			ld->ops->receive_buf(tty, data, flags, count);
642 		tty_ldisc_deref(ld);
643 	}
644 }
645 
646 /* tty callbacks */
647 
648 static int open(struct tty_struct *tty, struct file *filp)
649 {
650 	struct slgt_info *info;
651 	int retval, line;
652 	unsigned long flags;
653 
654 	line = tty->index;
655 	if (line >= slgt_device_count) {
656 		DBGERR(("%s: open with invalid line #%d.\n", driver_name, line));
657 		return -ENODEV;
658 	}
659 
660 	info = slgt_device_list;
661 	while(info && info->line != line)
662 		info = info->next_device;
663 	if (sanity_check(info, tty->name, "open"))
664 		return -ENODEV;
665 	if (info->init_error) {
666 		DBGERR(("%s init error=%d\n", info->device_name, info->init_error));
667 		return -ENODEV;
668 	}
669 
670 	tty->driver_data = info;
671 	info->port.tty = tty;
672 
673 	DBGINFO(("%s open, old ref count = %d\n", info->device_name, info->port.count));
674 
675 	mutex_lock(&info->port.mutex);
676 	info->port.low_latency = (info->port.flags & ASYNC_LOW_LATENCY) ? 1 : 0;
677 
678 	spin_lock_irqsave(&info->netlock, flags);
679 	if (info->netcount) {
680 		retval = -EBUSY;
681 		spin_unlock_irqrestore(&info->netlock, flags);
682 		mutex_unlock(&info->port.mutex);
683 		goto cleanup;
684 	}
685 	info->port.count++;
686 	spin_unlock_irqrestore(&info->netlock, flags);
687 
688 	if (info->port.count == 1) {
689 		/* 1st open on this device, init hardware */
690 		retval = startup(info);
691 		if (retval < 0) {
692 			mutex_unlock(&info->port.mutex);
693 			goto cleanup;
694 		}
695 	}
696 	mutex_unlock(&info->port.mutex);
697 	retval = block_til_ready(tty, filp, info);
698 	if (retval) {
699 		DBGINFO(("%s block_til_ready rc=%d\n", info->device_name, retval));
700 		goto cleanup;
701 	}
702 
703 	retval = 0;
704 
705 cleanup:
706 	if (retval) {
707 		if (tty->count == 1)
708 			info->port.tty = NULL; /* tty layer will release tty struct */
709 		if(info->port.count)
710 			info->port.count--;
711 	}
712 
713 	DBGINFO(("%s open rc=%d\n", info->device_name, retval));
714 	return retval;
715 }
716 
717 static void close(struct tty_struct *tty, struct file *filp)
718 {
719 	struct slgt_info *info = tty->driver_data;
720 
721 	if (sanity_check(info, tty->name, "close"))
722 		return;
723 	DBGINFO(("%s close entry, count=%d\n", info->device_name, info->port.count));
724 
725 	if (tty_port_close_start(&info->port, tty, filp) == 0)
726 		goto cleanup;
727 
728 	mutex_lock(&info->port.mutex);
729  	if (info->port.flags & ASYNC_INITIALIZED)
730  		wait_until_sent(tty, info->timeout);
731 	flush_buffer(tty);
732 	tty_ldisc_flush(tty);
733 
734 	shutdown(info);
735 	mutex_unlock(&info->port.mutex);
736 
737 	tty_port_close_end(&info->port, tty);
738 	info->port.tty = NULL;
739 cleanup:
740 	DBGINFO(("%s close exit, count=%d\n", tty->driver->name, info->port.count));
741 }
742 
743 static void hangup(struct tty_struct *tty)
744 {
745 	struct slgt_info *info = tty->driver_data;
746 	unsigned long flags;
747 
748 	if (sanity_check(info, tty->name, "hangup"))
749 		return;
750 	DBGINFO(("%s hangup\n", info->device_name));
751 
752 	flush_buffer(tty);
753 
754 	mutex_lock(&info->port.mutex);
755 	shutdown(info);
756 
757 	spin_lock_irqsave(&info->port.lock, flags);
758 	info->port.count = 0;
759 	info->port.flags &= ~ASYNC_NORMAL_ACTIVE;
760 	info->port.tty = NULL;
761 	spin_unlock_irqrestore(&info->port.lock, flags);
762 	mutex_unlock(&info->port.mutex);
763 
764 	wake_up_interruptible(&info->port.open_wait);
765 }
766 
767 static void set_termios(struct tty_struct *tty, struct ktermios *old_termios)
768 {
769 	struct slgt_info *info = tty->driver_data;
770 	unsigned long flags;
771 
772 	DBGINFO(("%s set_termios\n", tty->driver->name));
773 
774 	change_params(info);
775 
776 	/* Handle transition to B0 status */
777 	if (old_termios->c_cflag & CBAUD &&
778 	    !(tty->termios.c_cflag & CBAUD)) {
779 		info->signals &= ~(SerialSignal_RTS | SerialSignal_DTR);
780 		spin_lock_irqsave(&info->lock,flags);
781 		set_signals(info);
782 		spin_unlock_irqrestore(&info->lock,flags);
783 	}
784 
785 	/* Handle transition away from B0 status */
786 	if (!(old_termios->c_cflag & CBAUD) &&
787 	    tty->termios.c_cflag & CBAUD) {
788 		info->signals |= SerialSignal_DTR;
789  		if (!(tty->termios.c_cflag & CRTSCTS) ||
790  		    !test_bit(TTY_THROTTLED, &tty->flags)) {
791 			info->signals |= SerialSignal_RTS;
792  		}
793 		spin_lock_irqsave(&info->lock,flags);
794 	 	set_signals(info);
795 		spin_unlock_irqrestore(&info->lock,flags);
796 	}
797 
798 	/* Handle turning off CRTSCTS */
799 	if (old_termios->c_cflag & CRTSCTS &&
800 	    !(tty->termios.c_cflag & CRTSCTS)) {
801 		tty->hw_stopped = 0;
802 		tx_release(tty);
803 	}
804 }
805 
806 static void update_tx_timer(struct slgt_info *info)
807 {
808 	/*
809 	 * use worst case speed of 1200bps to calculate transmit timeout
810 	 * based on data in buffers (tbuf_bytes) and FIFO (128 bytes)
811 	 */
812 	if (info->params.mode == MGSL_MODE_HDLC) {
813 		int timeout  = (tbuf_bytes(info) * 7) + 1000;
814 		mod_timer(&info->tx_timer, jiffies + msecs_to_jiffies(timeout));
815 	}
816 }
817 
818 static int write(struct tty_struct *tty,
819 		 const unsigned char *buf, int count)
820 {
821 	int ret = 0;
822 	struct slgt_info *info = tty->driver_data;
823 	unsigned long flags;
824 
825 	if (sanity_check(info, tty->name, "write"))
826 		return -EIO;
827 
828 	DBGINFO(("%s write count=%d\n", info->device_name, count));
829 
830 	if (!info->tx_buf || (count > info->max_frame_size))
831 		return -EIO;
832 
833 	if (!count || tty->stopped || tty->hw_stopped)
834 		return 0;
835 
836 	spin_lock_irqsave(&info->lock, flags);
837 
838 	if (info->tx_count) {
839 		/* send accumulated data from send_char() */
840 		if (!tx_load(info, info->tx_buf, info->tx_count))
841 			goto cleanup;
842 		info->tx_count = 0;
843 	}
844 
845 	if (tx_load(info, buf, count))
846 		ret = count;
847 
848 cleanup:
849 	spin_unlock_irqrestore(&info->lock, flags);
850 	DBGINFO(("%s write rc=%d\n", info->device_name, ret));
851 	return ret;
852 }
853 
854 static int put_char(struct tty_struct *tty, unsigned char ch)
855 {
856 	struct slgt_info *info = tty->driver_data;
857 	unsigned long flags;
858 	int ret = 0;
859 
860 	if (sanity_check(info, tty->name, "put_char"))
861 		return 0;
862 	DBGINFO(("%s put_char(%d)\n", info->device_name, ch));
863 	if (!info->tx_buf)
864 		return 0;
865 	spin_lock_irqsave(&info->lock,flags);
866 	if (info->tx_count < info->max_frame_size) {
867 		info->tx_buf[info->tx_count++] = ch;
868 		ret = 1;
869 	}
870 	spin_unlock_irqrestore(&info->lock,flags);
871 	return ret;
872 }
873 
874 static void send_xchar(struct tty_struct *tty, char ch)
875 {
876 	struct slgt_info *info = tty->driver_data;
877 	unsigned long flags;
878 
879 	if (sanity_check(info, tty->name, "send_xchar"))
880 		return;
881 	DBGINFO(("%s send_xchar(%d)\n", info->device_name, ch));
882 	info->x_char = ch;
883 	if (ch) {
884 		spin_lock_irqsave(&info->lock,flags);
885 		if (!info->tx_enabled)
886 		 	tx_start(info);
887 		spin_unlock_irqrestore(&info->lock,flags);
888 	}
889 }
890 
891 static void wait_until_sent(struct tty_struct *tty, int timeout)
892 {
893 	struct slgt_info *info = tty->driver_data;
894 	unsigned long orig_jiffies, char_time;
895 
896 	if (!info )
897 		return;
898 	if (sanity_check(info, tty->name, "wait_until_sent"))
899 		return;
900 	DBGINFO(("%s wait_until_sent entry\n", info->device_name));
901 	if (!(info->port.flags & ASYNC_INITIALIZED))
902 		goto exit;
903 
904 	orig_jiffies = jiffies;
905 
906 	/* Set check interval to 1/5 of estimated time to
907 	 * send a character, and make it at least 1. The check
908 	 * interval should also be less than the timeout.
909 	 * Note: use tight timings here to satisfy the NIST-PCTS.
910 	 */
911 
912 	if (info->params.data_rate) {
913 	       	char_time = info->timeout/(32 * 5);
914 		if (!char_time)
915 			char_time++;
916 	} else
917 		char_time = 1;
918 
919 	if (timeout)
920 		char_time = min_t(unsigned long, char_time, timeout);
921 
922 	while (info->tx_active) {
923 		msleep_interruptible(jiffies_to_msecs(char_time));
924 		if (signal_pending(current))
925 			break;
926 		if (timeout && time_after(jiffies, orig_jiffies + timeout))
927 			break;
928 	}
929 exit:
930 	DBGINFO(("%s wait_until_sent exit\n", info->device_name));
931 }
932 
933 static int write_room(struct tty_struct *tty)
934 {
935 	struct slgt_info *info = tty->driver_data;
936 	int ret;
937 
938 	if (sanity_check(info, tty->name, "write_room"))
939 		return 0;
940 	ret = (info->tx_active) ? 0 : HDLC_MAX_FRAME_SIZE;
941 	DBGINFO(("%s write_room=%d\n", info->device_name, ret));
942 	return ret;
943 }
944 
945 static void flush_chars(struct tty_struct *tty)
946 {
947 	struct slgt_info *info = tty->driver_data;
948 	unsigned long flags;
949 
950 	if (sanity_check(info, tty->name, "flush_chars"))
951 		return;
952 	DBGINFO(("%s flush_chars entry tx_count=%d\n", info->device_name, info->tx_count));
953 
954 	if (info->tx_count <= 0 || tty->stopped ||
955 	    tty->hw_stopped || !info->tx_buf)
956 		return;
957 
958 	DBGINFO(("%s flush_chars start transmit\n", info->device_name));
959 
960 	spin_lock_irqsave(&info->lock,flags);
961 	if (info->tx_count && tx_load(info, info->tx_buf, info->tx_count))
962 		info->tx_count = 0;
963 	spin_unlock_irqrestore(&info->lock,flags);
964 }
965 
966 static void flush_buffer(struct tty_struct *tty)
967 {
968 	struct slgt_info *info = tty->driver_data;
969 	unsigned long flags;
970 
971 	if (sanity_check(info, tty->name, "flush_buffer"))
972 		return;
973 	DBGINFO(("%s flush_buffer\n", info->device_name));
974 
975 	spin_lock_irqsave(&info->lock, flags);
976 	info->tx_count = 0;
977 	spin_unlock_irqrestore(&info->lock, flags);
978 
979 	tty_wakeup(tty);
980 }
981 
982 /*
983  * throttle (stop) transmitter
984  */
985 static void tx_hold(struct tty_struct *tty)
986 {
987 	struct slgt_info *info = tty->driver_data;
988 	unsigned long flags;
989 
990 	if (sanity_check(info, tty->name, "tx_hold"))
991 		return;
992 	DBGINFO(("%s tx_hold\n", info->device_name));
993 	spin_lock_irqsave(&info->lock,flags);
994 	if (info->tx_enabled && info->params.mode == MGSL_MODE_ASYNC)
995 	 	tx_stop(info);
996 	spin_unlock_irqrestore(&info->lock,flags);
997 }
998 
999 /*
1000  * release (start) transmitter
1001  */
1002 static void tx_release(struct tty_struct *tty)
1003 {
1004 	struct slgt_info *info = tty->driver_data;
1005 	unsigned long flags;
1006 
1007 	if (sanity_check(info, tty->name, "tx_release"))
1008 		return;
1009 	DBGINFO(("%s tx_release\n", info->device_name));
1010 	spin_lock_irqsave(&info->lock, flags);
1011 	if (info->tx_count && tx_load(info, info->tx_buf, info->tx_count))
1012 		info->tx_count = 0;
1013 	spin_unlock_irqrestore(&info->lock, flags);
1014 }
1015 
1016 /*
1017  * Service an IOCTL request
1018  *
1019  * Arguments
1020  *
1021  * 	tty	pointer to tty instance data
1022  * 	cmd	IOCTL command code
1023  * 	arg	command argument/context
1024  *
1025  * Return 0 if success, otherwise error code
1026  */
1027 static int ioctl(struct tty_struct *tty,
1028 		 unsigned int cmd, unsigned long arg)
1029 {
1030 	struct slgt_info *info = tty->driver_data;
1031 	void __user *argp = (void __user *)arg;
1032 	int ret;
1033 
1034 	if (sanity_check(info, tty->name, "ioctl"))
1035 		return -ENODEV;
1036 	DBGINFO(("%s ioctl() cmd=%08X\n", info->device_name, cmd));
1037 
1038 	if ((cmd != TIOCGSERIAL) && (cmd != TIOCSSERIAL) &&
1039 	    (cmd != TIOCMIWAIT)) {
1040 		if (tty->flags & (1 << TTY_IO_ERROR))
1041 		    return -EIO;
1042 	}
1043 
1044 	switch (cmd) {
1045 	case MGSL_IOCWAITEVENT:
1046 		return wait_mgsl_event(info, argp);
1047 	case TIOCMIWAIT:
1048 		return modem_input_wait(info,(int)arg);
1049 	case MGSL_IOCSGPIO:
1050 		return set_gpio(info, argp);
1051 	case MGSL_IOCGGPIO:
1052 		return get_gpio(info, argp);
1053 	case MGSL_IOCWAITGPIO:
1054 		return wait_gpio(info, argp);
1055 	case MGSL_IOCGXSYNC:
1056 		return get_xsync(info, argp);
1057 	case MGSL_IOCSXSYNC:
1058 		return set_xsync(info, (int)arg);
1059 	case MGSL_IOCGXCTRL:
1060 		return get_xctrl(info, argp);
1061 	case MGSL_IOCSXCTRL:
1062 		return set_xctrl(info, (int)arg);
1063 	}
1064 	mutex_lock(&info->port.mutex);
1065 	switch (cmd) {
1066 	case MGSL_IOCGPARAMS:
1067 		ret = get_params(info, argp);
1068 		break;
1069 	case MGSL_IOCSPARAMS:
1070 		ret = set_params(info, argp);
1071 		break;
1072 	case MGSL_IOCGTXIDLE:
1073 		ret = get_txidle(info, argp);
1074 		break;
1075 	case MGSL_IOCSTXIDLE:
1076 		ret = set_txidle(info, (int)arg);
1077 		break;
1078 	case MGSL_IOCTXENABLE:
1079 		ret = tx_enable(info, (int)arg);
1080 		break;
1081 	case MGSL_IOCRXENABLE:
1082 		ret = rx_enable(info, (int)arg);
1083 		break;
1084 	case MGSL_IOCTXABORT:
1085 		ret = tx_abort(info);
1086 		break;
1087 	case MGSL_IOCGSTATS:
1088 		ret = get_stats(info, argp);
1089 		break;
1090 	case MGSL_IOCGIF:
1091 		ret = get_interface(info, argp);
1092 		break;
1093 	case MGSL_IOCSIF:
1094 		ret = set_interface(info,(int)arg);
1095 		break;
1096 	default:
1097 		ret = -ENOIOCTLCMD;
1098 	}
1099 	mutex_unlock(&info->port.mutex);
1100 	return ret;
1101 }
1102 
1103 static int get_icount(struct tty_struct *tty,
1104 				struct serial_icounter_struct *icount)
1105 
1106 {
1107 	struct slgt_info *info = tty->driver_data;
1108 	struct mgsl_icount cnow;	/* kernel counter temps */
1109 	unsigned long flags;
1110 
1111 	spin_lock_irqsave(&info->lock,flags);
1112 	cnow = info->icount;
1113 	spin_unlock_irqrestore(&info->lock,flags);
1114 
1115 	icount->cts = cnow.cts;
1116 	icount->dsr = cnow.dsr;
1117 	icount->rng = cnow.rng;
1118 	icount->dcd = cnow.dcd;
1119 	icount->rx = cnow.rx;
1120 	icount->tx = cnow.tx;
1121 	icount->frame = cnow.frame;
1122 	icount->overrun = cnow.overrun;
1123 	icount->parity = cnow.parity;
1124 	icount->brk = cnow.brk;
1125 	icount->buf_overrun = cnow.buf_overrun;
1126 
1127 	return 0;
1128 }
1129 
1130 /*
1131  * support for 32 bit ioctl calls on 64 bit systems
1132  */
1133 #ifdef CONFIG_COMPAT
1134 static long get_params32(struct slgt_info *info, struct MGSL_PARAMS32 __user *user_params)
1135 {
1136 	struct MGSL_PARAMS32 tmp_params;
1137 
1138 	DBGINFO(("%s get_params32\n", info->device_name));
1139 	memset(&tmp_params, 0, sizeof(tmp_params));
1140 	tmp_params.mode            = (compat_ulong_t)info->params.mode;
1141 	tmp_params.loopback        = info->params.loopback;
1142 	tmp_params.flags           = info->params.flags;
1143 	tmp_params.encoding        = info->params.encoding;
1144 	tmp_params.clock_speed     = (compat_ulong_t)info->params.clock_speed;
1145 	tmp_params.addr_filter     = info->params.addr_filter;
1146 	tmp_params.crc_type        = info->params.crc_type;
1147 	tmp_params.preamble_length = info->params.preamble_length;
1148 	tmp_params.preamble        = info->params.preamble;
1149 	tmp_params.data_rate       = (compat_ulong_t)info->params.data_rate;
1150 	tmp_params.data_bits       = info->params.data_bits;
1151 	tmp_params.stop_bits       = info->params.stop_bits;
1152 	tmp_params.parity          = info->params.parity;
1153 	if (copy_to_user(user_params, &tmp_params, sizeof(struct MGSL_PARAMS32)))
1154 		return -EFAULT;
1155 	return 0;
1156 }
1157 
1158 static long set_params32(struct slgt_info *info, struct MGSL_PARAMS32 __user *new_params)
1159 {
1160 	struct MGSL_PARAMS32 tmp_params;
1161 
1162 	DBGINFO(("%s set_params32\n", info->device_name));
1163 	if (copy_from_user(&tmp_params, new_params, sizeof(struct MGSL_PARAMS32)))
1164 		return -EFAULT;
1165 
1166 	spin_lock(&info->lock);
1167 	if (tmp_params.mode == MGSL_MODE_BASE_CLOCK) {
1168 		info->base_clock = tmp_params.clock_speed;
1169 	} else {
1170 		info->params.mode            = tmp_params.mode;
1171 		info->params.loopback        = tmp_params.loopback;
1172 		info->params.flags           = tmp_params.flags;
1173 		info->params.encoding        = tmp_params.encoding;
1174 		info->params.clock_speed     = tmp_params.clock_speed;
1175 		info->params.addr_filter     = tmp_params.addr_filter;
1176 		info->params.crc_type        = tmp_params.crc_type;
1177 		info->params.preamble_length = tmp_params.preamble_length;
1178 		info->params.preamble        = tmp_params.preamble;
1179 		info->params.data_rate       = tmp_params.data_rate;
1180 		info->params.data_bits       = tmp_params.data_bits;
1181 		info->params.stop_bits       = tmp_params.stop_bits;
1182 		info->params.parity          = tmp_params.parity;
1183 	}
1184 	spin_unlock(&info->lock);
1185 
1186 	program_hw(info);
1187 
1188 	return 0;
1189 }
1190 
1191 static long slgt_compat_ioctl(struct tty_struct *tty,
1192 			 unsigned int cmd, unsigned long arg)
1193 {
1194 	struct slgt_info *info = tty->driver_data;
1195 	int rc = -ENOIOCTLCMD;
1196 
1197 	if (sanity_check(info, tty->name, "compat_ioctl"))
1198 		return -ENODEV;
1199 	DBGINFO(("%s compat_ioctl() cmd=%08X\n", info->device_name, cmd));
1200 
1201 	switch (cmd) {
1202 
1203 	case MGSL_IOCSPARAMS32:
1204 		rc = set_params32(info, compat_ptr(arg));
1205 		break;
1206 
1207 	case MGSL_IOCGPARAMS32:
1208 		rc = get_params32(info, compat_ptr(arg));
1209 		break;
1210 
1211 	case MGSL_IOCGPARAMS:
1212 	case MGSL_IOCSPARAMS:
1213 	case MGSL_IOCGTXIDLE:
1214 	case MGSL_IOCGSTATS:
1215 	case MGSL_IOCWAITEVENT:
1216 	case MGSL_IOCGIF:
1217 	case MGSL_IOCSGPIO:
1218 	case MGSL_IOCGGPIO:
1219 	case MGSL_IOCWAITGPIO:
1220 	case MGSL_IOCGXSYNC:
1221 	case MGSL_IOCGXCTRL:
1222 	case MGSL_IOCSTXIDLE:
1223 	case MGSL_IOCTXENABLE:
1224 	case MGSL_IOCRXENABLE:
1225 	case MGSL_IOCTXABORT:
1226 	case TIOCMIWAIT:
1227 	case MGSL_IOCSIF:
1228 	case MGSL_IOCSXSYNC:
1229 	case MGSL_IOCSXCTRL:
1230 		rc = ioctl(tty, cmd, arg);
1231 		break;
1232 	}
1233 
1234 	DBGINFO(("%s compat_ioctl() cmd=%08X rc=%d\n", info->device_name, cmd, rc));
1235 	return rc;
1236 }
1237 #else
1238 #define slgt_compat_ioctl NULL
1239 #endif /* ifdef CONFIG_COMPAT */
1240 
1241 /*
1242  * proc fs support
1243  */
1244 static inline void line_info(struct seq_file *m, struct slgt_info *info)
1245 {
1246 	char stat_buf[30];
1247 	unsigned long flags;
1248 
1249 	seq_printf(m, "%s: IO=%08X IRQ=%d MaxFrameSize=%u\n",
1250 		      info->device_name, info->phys_reg_addr,
1251 		      info->irq_level, info->max_frame_size);
1252 
1253 	/* output current serial signal states */
1254 	spin_lock_irqsave(&info->lock,flags);
1255 	get_signals(info);
1256 	spin_unlock_irqrestore(&info->lock,flags);
1257 
1258 	stat_buf[0] = 0;
1259 	stat_buf[1] = 0;
1260 	if (info->signals & SerialSignal_RTS)
1261 		strcat(stat_buf, "|RTS");
1262 	if (info->signals & SerialSignal_CTS)
1263 		strcat(stat_buf, "|CTS");
1264 	if (info->signals & SerialSignal_DTR)
1265 		strcat(stat_buf, "|DTR");
1266 	if (info->signals & SerialSignal_DSR)
1267 		strcat(stat_buf, "|DSR");
1268 	if (info->signals & SerialSignal_DCD)
1269 		strcat(stat_buf, "|CD");
1270 	if (info->signals & SerialSignal_RI)
1271 		strcat(stat_buf, "|RI");
1272 
1273 	if (info->params.mode != MGSL_MODE_ASYNC) {
1274 		seq_printf(m, "\tHDLC txok:%d rxok:%d",
1275 			       info->icount.txok, info->icount.rxok);
1276 		if (info->icount.txunder)
1277 			seq_printf(m, " txunder:%d", info->icount.txunder);
1278 		if (info->icount.txabort)
1279 			seq_printf(m, " txabort:%d", info->icount.txabort);
1280 		if (info->icount.rxshort)
1281 			seq_printf(m, " rxshort:%d", info->icount.rxshort);
1282 		if (info->icount.rxlong)
1283 			seq_printf(m, " rxlong:%d", info->icount.rxlong);
1284 		if (info->icount.rxover)
1285 			seq_printf(m, " rxover:%d", info->icount.rxover);
1286 		if (info->icount.rxcrc)
1287 			seq_printf(m, " rxcrc:%d", info->icount.rxcrc);
1288 	} else {
1289 		seq_printf(m, "\tASYNC tx:%d rx:%d",
1290 			       info->icount.tx, info->icount.rx);
1291 		if (info->icount.frame)
1292 			seq_printf(m, " fe:%d", info->icount.frame);
1293 		if (info->icount.parity)
1294 			seq_printf(m, " pe:%d", info->icount.parity);
1295 		if (info->icount.brk)
1296 			seq_printf(m, " brk:%d", info->icount.brk);
1297 		if (info->icount.overrun)
1298 			seq_printf(m, " oe:%d", info->icount.overrun);
1299 	}
1300 
1301 	/* Append serial signal status to end */
1302 	seq_printf(m, " %s\n", stat_buf+1);
1303 
1304 	seq_printf(m, "\ttxactive=%d bh_req=%d bh_run=%d pending_bh=%x\n",
1305 		       info->tx_active,info->bh_requested,info->bh_running,
1306 		       info->pending_bh);
1307 }
1308 
1309 /* Called to print information about devices
1310  */
1311 static int synclink_gt_proc_show(struct seq_file *m, void *v)
1312 {
1313 	struct slgt_info *info;
1314 
1315 	seq_puts(m, "synclink_gt driver\n");
1316 
1317 	info = slgt_device_list;
1318 	while( info ) {
1319 		line_info(m, info);
1320 		info = info->next_device;
1321 	}
1322 	return 0;
1323 }
1324 
1325 static int synclink_gt_proc_open(struct inode *inode, struct file *file)
1326 {
1327 	return single_open(file, synclink_gt_proc_show, NULL);
1328 }
1329 
1330 static const struct file_operations synclink_gt_proc_fops = {
1331 	.owner		= THIS_MODULE,
1332 	.open		= synclink_gt_proc_open,
1333 	.read		= seq_read,
1334 	.llseek		= seq_lseek,
1335 	.release	= single_release,
1336 };
1337 
1338 /*
1339  * return count of bytes in transmit buffer
1340  */
1341 static int chars_in_buffer(struct tty_struct *tty)
1342 {
1343 	struct slgt_info *info = tty->driver_data;
1344 	int count;
1345 	if (sanity_check(info, tty->name, "chars_in_buffer"))
1346 		return 0;
1347 	count = tbuf_bytes(info);
1348 	DBGINFO(("%s chars_in_buffer()=%d\n", info->device_name, count));
1349 	return count;
1350 }
1351 
1352 /*
1353  * signal remote device to throttle send data (our receive data)
1354  */
1355 static void throttle(struct tty_struct * tty)
1356 {
1357 	struct slgt_info *info = tty->driver_data;
1358 	unsigned long flags;
1359 
1360 	if (sanity_check(info, tty->name, "throttle"))
1361 		return;
1362 	DBGINFO(("%s throttle\n", info->device_name));
1363 	if (I_IXOFF(tty))
1364 		send_xchar(tty, STOP_CHAR(tty));
1365  	if (tty->termios.c_cflag & CRTSCTS) {
1366 		spin_lock_irqsave(&info->lock,flags);
1367 		info->signals &= ~SerialSignal_RTS;
1368 	 	set_signals(info);
1369 		spin_unlock_irqrestore(&info->lock,flags);
1370 	}
1371 }
1372 
1373 /*
1374  * signal remote device to stop throttling send data (our receive data)
1375  */
1376 static void unthrottle(struct tty_struct * tty)
1377 {
1378 	struct slgt_info *info = tty->driver_data;
1379 	unsigned long flags;
1380 
1381 	if (sanity_check(info, tty->name, "unthrottle"))
1382 		return;
1383 	DBGINFO(("%s unthrottle\n", info->device_name));
1384 	if (I_IXOFF(tty)) {
1385 		if (info->x_char)
1386 			info->x_char = 0;
1387 		else
1388 			send_xchar(tty, START_CHAR(tty));
1389 	}
1390  	if (tty->termios.c_cflag & CRTSCTS) {
1391 		spin_lock_irqsave(&info->lock,flags);
1392 		info->signals |= SerialSignal_RTS;
1393 	 	set_signals(info);
1394 		spin_unlock_irqrestore(&info->lock,flags);
1395 	}
1396 }
1397 
1398 /*
1399  * set or clear transmit break condition
1400  * break_state	-1=set break condition, 0=clear
1401  */
1402 static int set_break(struct tty_struct *tty, int break_state)
1403 {
1404 	struct slgt_info *info = tty->driver_data;
1405 	unsigned short value;
1406 	unsigned long flags;
1407 
1408 	if (sanity_check(info, tty->name, "set_break"))
1409 		return -EINVAL;
1410 	DBGINFO(("%s set_break(%d)\n", info->device_name, break_state));
1411 
1412 	spin_lock_irqsave(&info->lock,flags);
1413 	value = rd_reg16(info, TCR);
1414  	if (break_state == -1)
1415 		value |= BIT6;
1416 	else
1417 		value &= ~BIT6;
1418 	wr_reg16(info, TCR, value);
1419 	spin_unlock_irqrestore(&info->lock,flags);
1420 	return 0;
1421 }
1422 
1423 #if SYNCLINK_GENERIC_HDLC
1424 
1425 /**
1426  * called by generic HDLC layer when protocol selected (PPP, frame relay, etc.)
1427  * set encoding and frame check sequence (FCS) options
1428  *
1429  * dev       pointer to network device structure
1430  * encoding  serial encoding setting
1431  * parity    FCS setting
1432  *
1433  * returns 0 if success, otherwise error code
1434  */
1435 static int hdlcdev_attach(struct net_device *dev, unsigned short encoding,
1436 			  unsigned short parity)
1437 {
1438 	struct slgt_info *info = dev_to_port(dev);
1439 	unsigned char  new_encoding;
1440 	unsigned short new_crctype;
1441 
1442 	/* return error if TTY interface open */
1443 	if (info->port.count)
1444 		return -EBUSY;
1445 
1446 	DBGINFO(("%s hdlcdev_attach\n", info->device_name));
1447 
1448 	switch (encoding)
1449 	{
1450 	case ENCODING_NRZ:        new_encoding = HDLC_ENCODING_NRZ; break;
1451 	case ENCODING_NRZI:       new_encoding = HDLC_ENCODING_NRZI_SPACE; break;
1452 	case ENCODING_FM_MARK:    new_encoding = HDLC_ENCODING_BIPHASE_MARK; break;
1453 	case ENCODING_FM_SPACE:   new_encoding = HDLC_ENCODING_BIPHASE_SPACE; break;
1454 	case ENCODING_MANCHESTER: new_encoding = HDLC_ENCODING_BIPHASE_LEVEL; break;
1455 	default: return -EINVAL;
1456 	}
1457 
1458 	switch (parity)
1459 	{
1460 	case PARITY_NONE:            new_crctype = HDLC_CRC_NONE; break;
1461 	case PARITY_CRC16_PR1_CCITT: new_crctype = HDLC_CRC_16_CCITT; break;
1462 	case PARITY_CRC32_PR1_CCITT: new_crctype = HDLC_CRC_32_CCITT; break;
1463 	default: return -EINVAL;
1464 	}
1465 
1466 	info->params.encoding = new_encoding;
1467 	info->params.crc_type = new_crctype;
1468 
1469 	/* if network interface up, reprogram hardware */
1470 	if (info->netcount)
1471 		program_hw(info);
1472 
1473 	return 0;
1474 }
1475 
1476 /**
1477  * called by generic HDLC layer to send frame
1478  *
1479  * skb  socket buffer containing HDLC frame
1480  * dev  pointer to network device structure
1481  */
1482 static netdev_tx_t hdlcdev_xmit(struct sk_buff *skb,
1483 				      struct net_device *dev)
1484 {
1485 	struct slgt_info *info = dev_to_port(dev);
1486 	unsigned long flags;
1487 
1488 	DBGINFO(("%s hdlc_xmit\n", dev->name));
1489 
1490 	if (!skb->len)
1491 		return NETDEV_TX_OK;
1492 
1493 	/* stop sending until this frame completes */
1494 	netif_stop_queue(dev);
1495 
1496 	/* update network statistics */
1497 	dev->stats.tx_packets++;
1498 	dev->stats.tx_bytes += skb->len;
1499 
1500 	/* save start time for transmit timeout detection */
1501 	dev->trans_start = jiffies;
1502 
1503 	spin_lock_irqsave(&info->lock, flags);
1504 	tx_load(info, skb->data, skb->len);
1505 	spin_unlock_irqrestore(&info->lock, flags);
1506 
1507 	/* done with socket buffer, so free it */
1508 	dev_kfree_skb(skb);
1509 
1510 	return NETDEV_TX_OK;
1511 }
1512 
1513 /**
1514  * called by network layer when interface enabled
1515  * claim resources and initialize hardware
1516  *
1517  * dev  pointer to network device structure
1518  *
1519  * returns 0 if success, otherwise error code
1520  */
1521 static int hdlcdev_open(struct net_device *dev)
1522 {
1523 	struct slgt_info *info = dev_to_port(dev);
1524 	int rc;
1525 	unsigned long flags;
1526 
1527 	if (!try_module_get(THIS_MODULE))
1528 		return -EBUSY;
1529 
1530 	DBGINFO(("%s hdlcdev_open\n", dev->name));
1531 
1532 	/* generic HDLC layer open processing */
1533 	rc = hdlc_open(dev);
1534 	if (rc)
1535 		return rc;
1536 
1537 	/* arbitrate between network and tty opens */
1538 	spin_lock_irqsave(&info->netlock, flags);
1539 	if (info->port.count != 0 || info->netcount != 0) {
1540 		DBGINFO(("%s hdlc_open busy\n", dev->name));
1541 		spin_unlock_irqrestore(&info->netlock, flags);
1542 		return -EBUSY;
1543 	}
1544 	info->netcount=1;
1545 	spin_unlock_irqrestore(&info->netlock, flags);
1546 
1547 	/* claim resources and init adapter */
1548 	if ((rc = startup(info)) != 0) {
1549 		spin_lock_irqsave(&info->netlock, flags);
1550 		info->netcount=0;
1551 		spin_unlock_irqrestore(&info->netlock, flags);
1552 		return rc;
1553 	}
1554 
1555 	/* assert RTS and DTR, apply hardware settings */
1556 	info->signals |= SerialSignal_RTS | SerialSignal_DTR;
1557 	program_hw(info);
1558 
1559 	/* enable network layer transmit */
1560 	dev->trans_start = jiffies;
1561 	netif_start_queue(dev);
1562 
1563 	/* inform generic HDLC layer of current DCD status */
1564 	spin_lock_irqsave(&info->lock, flags);
1565 	get_signals(info);
1566 	spin_unlock_irqrestore(&info->lock, flags);
1567 	if (info->signals & SerialSignal_DCD)
1568 		netif_carrier_on(dev);
1569 	else
1570 		netif_carrier_off(dev);
1571 	return 0;
1572 }
1573 
1574 /**
1575  * called by network layer when interface is disabled
1576  * shutdown hardware and release resources
1577  *
1578  * dev  pointer to network device structure
1579  *
1580  * returns 0 if success, otherwise error code
1581  */
1582 static int hdlcdev_close(struct net_device *dev)
1583 {
1584 	struct slgt_info *info = dev_to_port(dev);
1585 	unsigned long flags;
1586 
1587 	DBGINFO(("%s hdlcdev_close\n", dev->name));
1588 
1589 	netif_stop_queue(dev);
1590 
1591 	/* shutdown adapter and release resources */
1592 	shutdown(info);
1593 
1594 	hdlc_close(dev);
1595 
1596 	spin_lock_irqsave(&info->netlock, flags);
1597 	info->netcount=0;
1598 	spin_unlock_irqrestore(&info->netlock, flags);
1599 
1600 	module_put(THIS_MODULE);
1601 	return 0;
1602 }
1603 
1604 /**
1605  * called by network layer to process IOCTL call to network device
1606  *
1607  * dev  pointer to network device structure
1608  * ifr  pointer to network interface request structure
1609  * cmd  IOCTL command code
1610  *
1611  * returns 0 if success, otherwise error code
1612  */
1613 static int hdlcdev_ioctl(struct net_device *dev, struct ifreq *ifr, int cmd)
1614 {
1615 	const size_t size = sizeof(sync_serial_settings);
1616 	sync_serial_settings new_line;
1617 	sync_serial_settings __user *line = ifr->ifr_settings.ifs_ifsu.sync;
1618 	struct slgt_info *info = dev_to_port(dev);
1619 	unsigned int flags;
1620 
1621 	DBGINFO(("%s hdlcdev_ioctl\n", dev->name));
1622 
1623 	/* return error if TTY interface open */
1624 	if (info->port.count)
1625 		return -EBUSY;
1626 
1627 	if (cmd != SIOCWANDEV)
1628 		return hdlc_ioctl(dev, ifr, cmd);
1629 
1630 	memset(&new_line, 0, sizeof(new_line));
1631 
1632 	switch(ifr->ifr_settings.type) {
1633 	case IF_GET_IFACE: /* return current sync_serial_settings */
1634 
1635 		ifr->ifr_settings.type = IF_IFACE_SYNC_SERIAL;
1636 		if (ifr->ifr_settings.size < size) {
1637 			ifr->ifr_settings.size = size; /* data size wanted */
1638 			return -ENOBUFS;
1639 		}
1640 
1641 		flags = info->params.flags & (HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_RXC_DPLL |
1642 					      HDLC_FLAG_RXC_BRG    | HDLC_FLAG_RXC_TXCPIN |
1643 					      HDLC_FLAG_TXC_TXCPIN | HDLC_FLAG_TXC_DPLL |
1644 					      HDLC_FLAG_TXC_BRG    | HDLC_FLAG_TXC_RXCPIN);
1645 
1646 		switch (flags){
1647 		case (HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_TXCPIN): new_line.clock_type = CLOCK_EXT; break;
1648 		case (HDLC_FLAG_RXC_BRG    | HDLC_FLAG_TXC_BRG):    new_line.clock_type = CLOCK_INT; break;
1649 		case (HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_BRG):    new_line.clock_type = CLOCK_TXINT; break;
1650 		case (HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_RXCPIN): new_line.clock_type = CLOCK_TXFROMRX; break;
1651 		default: new_line.clock_type = CLOCK_DEFAULT;
1652 		}
1653 
1654 		new_line.clock_rate = info->params.clock_speed;
1655 		new_line.loopback   = info->params.loopback ? 1:0;
1656 
1657 		if (copy_to_user(line, &new_line, size))
1658 			return -EFAULT;
1659 		return 0;
1660 
1661 	case IF_IFACE_SYNC_SERIAL: /* set sync_serial_settings */
1662 
1663 		if(!capable(CAP_NET_ADMIN))
1664 			return -EPERM;
1665 		if (copy_from_user(&new_line, line, size))
1666 			return -EFAULT;
1667 
1668 		switch (new_line.clock_type)
1669 		{
1670 		case CLOCK_EXT:      flags = HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_TXCPIN; break;
1671 		case CLOCK_TXFROMRX: flags = HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_RXCPIN; break;
1672 		case CLOCK_INT:      flags = HDLC_FLAG_RXC_BRG    | HDLC_FLAG_TXC_BRG;    break;
1673 		case CLOCK_TXINT:    flags = HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_BRG;    break;
1674 		case CLOCK_DEFAULT:  flags = info->params.flags &
1675 					     (HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_RXC_DPLL |
1676 					      HDLC_FLAG_RXC_BRG    | HDLC_FLAG_RXC_TXCPIN |
1677 					      HDLC_FLAG_TXC_TXCPIN | HDLC_FLAG_TXC_DPLL |
1678 					      HDLC_FLAG_TXC_BRG    | HDLC_FLAG_TXC_RXCPIN); break;
1679 		default: return -EINVAL;
1680 		}
1681 
1682 		if (new_line.loopback != 0 && new_line.loopback != 1)
1683 			return -EINVAL;
1684 
1685 		info->params.flags &= ~(HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_RXC_DPLL |
1686 					HDLC_FLAG_RXC_BRG    | HDLC_FLAG_RXC_TXCPIN |
1687 					HDLC_FLAG_TXC_TXCPIN | HDLC_FLAG_TXC_DPLL |
1688 					HDLC_FLAG_TXC_BRG    | HDLC_FLAG_TXC_RXCPIN);
1689 		info->params.flags |= flags;
1690 
1691 		info->params.loopback = new_line.loopback;
1692 
1693 		if (flags & (HDLC_FLAG_RXC_BRG | HDLC_FLAG_TXC_BRG))
1694 			info->params.clock_speed = new_line.clock_rate;
1695 		else
1696 			info->params.clock_speed = 0;
1697 
1698 		/* if network interface up, reprogram hardware */
1699 		if (info->netcount)
1700 			program_hw(info);
1701 		return 0;
1702 
1703 	default:
1704 		return hdlc_ioctl(dev, ifr, cmd);
1705 	}
1706 }
1707 
1708 /**
1709  * called by network layer when transmit timeout is detected
1710  *
1711  * dev  pointer to network device structure
1712  */
1713 static void hdlcdev_tx_timeout(struct net_device *dev)
1714 {
1715 	struct slgt_info *info = dev_to_port(dev);
1716 	unsigned long flags;
1717 
1718 	DBGINFO(("%s hdlcdev_tx_timeout\n", dev->name));
1719 
1720 	dev->stats.tx_errors++;
1721 	dev->stats.tx_aborted_errors++;
1722 
1723 	spin_lock_irqsave(&info->lock,flags);
1724 	tx_stop(info);
1725 	spin_unlock_irqrestore(&info->lock,flags);
1726 
1727 	netif_wake_queue(dev);
1728 }
1729 
1730 /**
1731  * called by device driver when transmit completes
1732  * reenable network layer transmit if stopped
1733  *
1734  * info  pointer to device instance information
1735  */
1736 static void hdlcdev_tx_done(struct slgt_info *info)
1737 {
1738 	if (netif_queue_stopped(info->netdev))
1739 		netif_wake_queue(info->netdev);
1740 }
1741 
1742 /**
1743  * called by device driver when frame received
1744  * pass frame to network layer
1745  *
1746  * info  pointer to device instance information
1747  * buf   pointer to buffer contianing frame data
1748  * size  count of data bytes in buf
1749  */
1750 static void hdlcdev_rx(struct slgt_info *info, char *buf, int size)
1751 {
1752 	struct sk_buff *skb = dev_alloc_skb(size);
1753 	struct net_device *dev = info->netdev;
1754 
1755 	DBGINFO(("%s hdlcdev_rx\n", dev->name));
1756 
1757 	if (skb == NULL) {
1758 		DBGERR(("%s: can't alloc skb, drop packet\n", dev->name));
1759 		dev->stats.rx_dropped++;
1760 		return;
1761 	}
1762 
1763 	memcpy(skb_put(skb, size), buf, size);
1764 
1765 	skb->protocol = hdlc_type_trans(skb, dev);
1766 
1767 	dev->stats.rx_packets++;
1768 	dev->stats.rx_bytes += size;
1769 
1770 	netif_rx(skb);
1771 }
1772 
1773 static const struct net_device_ops hdlcdev_ops = {
1774 	.ndo_open       = hdlcdev_open,
1775 	.ndo_stop       = hdlcdev_close,
1776 	.ndo_change_mtu = hdlc_change_mtu,
1777 	.ndo_start_xmit = hdlc_start_xmit,
1778 	.ndo_do_ioctl   = hdlcdev_ioctl,
1779 	.ndo_tx_timeout = hdlcdev_tx_timeout,
1780 };
1781 
1782 /**
1783  * called by device driver when adding device instance
1784  * do generic HDLC initialization
1785  *
1786  * info  pointer to device instance information
1787  *
1788  * returns 0 if success, otherwise error code
1789  */
1790 static int hdlcdev_init(struct slgt_info *info)
1791 {
1792 	int rc;
1793 	struct net_device *dev;
1794 	hdlc_device *hdlc;
1795 
1796 	/* allocate and initialize network and HDLC layer objects */
1797 
1798 	dev = alloc_hdlcdev(info);
1799 	if (!dev) {
1800 		printk(KERN_ERR "%s hdlc device alloc failure\n", info->device_name);
1801 		return -ENOMEM;
1802 	}
1803 
1804 	/* for network layer reporting purposes only */
1805 	dev->mem_start = info->phys_reg_addr;
1806 	dev->mem_end   = info->phys_reg_addr + SLGT_REG_SIZE - 1;
1807 	dev->irq       = info->irq_level;
1808 
1809 	/* network layer callbacks and settings */
1810 	dev->netdev_ops	    = &hdlcdev_ops;
1811 	dev->watchdog_timeo = 10 * HZ;
1812 	dev->tx_queue_len   = 50;
1813 
1814 	/* generic HDLC layer callbacks and settings */
1815 	hdlc         = dev_to_hdlc(dev);
1816 	hdlc->attach = hdlcdev_attach;
1817 	hdlc->xmit   = hdlcdev_xmit;
1818 
1819 	/* register objects with HDLC layer */
1820 	rc = register_hdlc_device(dev);
1821 	if (rc) {
1822 		printk(KERN_WARNING "%s:unable to register hdlc device\n",__FILE__);
1823 		free_netdev(dev);
1824 		return rc;
1825 	}
1826 
1827 	info->netdev = dev;
1828 	return 0;
1829 }
1830 
1831 /**
1832  * called by device driver when removing device instance
1833  * do generic HDLC cleanup
1834  *
1835  * info  pointer to device instance information
1836  */
1837 static void hdlcdev_exit(struct slgt_info *info)
1838 {
1839 	unregister_hdlc_device(info->netdev);
1840 	free_netdev(info->netdev);
1841 	info->netdev = NULL;
1842 }
1843 
1844 #endif /* ifdef CONFIG_HDLC */
1845 
1846 /*
1847  * get async data from rx DMA buffers
1848  */
1849 static void rx_async(struct slgt_info *info)
1850 {
1851  	struct mgsl_icount *icount = &info->icount;
1852 	unsigned int start, end;
1853 	unsigned char *p;
1854 	unsigned char status;
1855 	struct slgt_desc *bufs = info->rbufs;
1856 	int i, count;
1857 	int chars = 0;
1858 	int stat;
1859 	unsigned char ch;
1860 
1861 	start = end = info->rbuf_current;
1862 
1863 	while(desc_complete(bufs[end])) {
1864 		count = desc_count(bufs[end]) - info->rbuf_index;
1865 		p     = bufs[end].buf + info->rbuf_index;
1866 
1867 		DBGISR(("%s rx_async count=%d\n", info->device_name, count));
1868 		DBGDATA(info, p, count, "rx");
1869 
1870 		for(i=0 ; i < count; i+=2, p+=2) {
1871 			ch = *p;
1872 			icount->rx++;
1873 
1874 			stat = 0;
1875 
1876 			status = *(p + 1) & (BIT1 + BIT0);
1877 			if (status) {
1878 				if (status & BIT1)
1879 					icount->parity++;
1880 				else if (status & BIT0)
1881 					icount->frame++;
1882 				/* discard char if tty control flags say so */
1883 				if (status & info->ignore_status_mask)
1884 					continue;
1885 				if (status & BIT1)
1886 					stat = TTY_PARITY;
1887 				else if (status & BIT0)
1888 					stat = TTY_FRAME;
1889 			}
1890 			tty_insert_flip_char(&info->port, ch, stat);
1891 			chars++;
1892 		}
1893 
1894 		if (i < count) {
1895 			/* receive buffer not completed */
1896 			info->rbuf_index += i;
1897 			mod_timer(&info->rx_timer, jiffies + 1);
1898 			break;
1899 		}
1900 
1901 		info->rbuf_index = 0;
1902 		free_rbufs(info, end, end);
1903 
1904 		if (++end == info->rbuf_count)
1905 			end = 0;
1906 
1907 		/* if entire list searched then no frame available */
1908 		if (end == start)
1909 			break;
1910 	}
1911 
1912 	if (chars)
1913 		tty_flip_buffer_push(&info->port);
1914 }
1915 
1916 /*
1917  * return next bottom half action to perform
1918  */
1919 static int bh_action(struct slgt_info *info)
1920 {
1921 	unsigned long flags;
1922 	int rc;
1923 
1924 	spin_lock_irqsave(&info->lock,flags);
1925 
1926 	if (info->pending_bh & BH_RECEIVE) {
1927 		info->pending_bh &= ~BH_RECEIVE;
1928 		rc = BH_RECEIVE;
1929 	} else if (info->pending_bh & BH_TRANSMIT) {
1930 		info->pending_bh &= ~BH_TRANSMIT;
1931 		rc = BH_TRANSMIT;
1932 	} else if (info->pending_bh & BH_STATUS) {
1933 		info->pending_bh &= ~BH_STATUS;
1934 		rc = BH_STATUS;
1935 	} else {
1936 		/* Mark BH routine as complete */
1937 		info->bh_running = false;
1938 		info->bh_requested = false;
1939 		rc = 0;
1940 	}
1941 
1942 	spin_unlock_irqrestore(&info->lock,flags);
1943 
1944 	return rc;
1945 }
1946 
1947 /*
1948  * perform bottom half processing
1949  */
1950 static void bh_handler(struct work_struct *work)
1951 {
1952 	struct slgt_info *info = container_of(work, struct slgt_info, task);
1953 	int action;
1954 
1955 	info->bh_running = true;
1956 
1957 	while((action = bh_action(info))) {
1958 		switch (action) {
1959 		case BH_RECEIVE:
1960 			DBGBH(("%s bh receive\n", info->device_name));
1961 			switch(info->params.mode) {
1962 			case MGSL_MODE_ASYNC:
1963 				rx_async(info);
1964 				break;
1965 			case MGSL_MODE_HDLC:
1966 				while(rx_get_frame(info));
1967 				break;
1968 			case MGSL_MODE_RAW:
1969 			case MGSL_MODE_MONOSYNC:
1970 			case MGSL_MODE_BISYNC:
1971 			case MGSL_MODE_XSYNC:
1972 				while(rx_get_buf(info));
1973 				break;
1974 			}
1975 			/* restart receiver if rx DMA buffers exhausted */
1976 			if (info->rx_restart)
1977 				rx_start(info);
1978 			break;
1979 		case BH_TRANSMIT:
1980 			bh_transmit(info);
1981 			break;
1982 		case BH_STATUS:
1983 			DBGBH(("%s bh status\n", info->device_name));
1984 			info->ri_chkcount = 0;
1985 			info->dsr_chkcount = 0;
1986 			info->dcd_chkcount = 0;
1987 			info->cts_chkcount = 0;
1988 			break;
1989 		default:
1990 			DBGBH(("%s unknown action\n", info->device_name));
1991 			break;
1992 		}
1993 	}
1994 	DBGBH(("%s bh_handler exit\n", info->device_name));
1995 }
1996 
1997 static void bh_transmit(struct slgt_info *info)
1998 {
1999 	struct tty_struct *tty = info->port.tty;
2000 
2001 	DBGBH(("%s bh_transmit\n", info->device_name));
2002 	if (tty)
2003 		tty_wakeup(tty);
2004 }
2005 
2006 static void dsr_change(struct slgt_info *info, unsigned short status)
2007 {
2008 	if (status & BIT3) {
2009 		info->signals |= SerialSignal_DSR;
2010 		info->input_signal_events.dsr_up++;
2011 	} else {
2012 		info->signals &= ~SerialSignal_DSR;
2013 		info->input_signal_events.dsr_down++;
2014 	}
2015 	DBGISR(("dsr_change %s signals=%04X\n", info->device_name, info->signals));
2016 	if ((info->dsr_chkcount)++ == IO_PIN_SHUTDOWN_LIMIT) {
2017 		slgt_irq_off(info, IRQ_DSR);
2018 		return;
2019 	}
2020 	info->icount.dsr++;
2021 	wake_up_interruptible(&info->status_event_wait_q);
2022 	wake_up_interruptible(&info->event_wait_q);
2023 	info->pending_bh |= BH_STATUS;
2024 }
2025 
2026 static void cts_change(struct slgt_info *info, unsigned short status)
2027 {
2028 	if (status & BIT2) {
2029 		info->signals |= SerialSignal_CTS;
2030 		info->input_signal_events.cts_up++;
2031 	} else {
2032 		info->signals &= ~SerialSignal_CTS;
2033 		info->input_signal_events.cts_down++;
2034 	}
2035 	DBGISR(("cts_change %s signals=%04X\n", info->device_name, info->signals));
2036 	if ((info->cts_chkcount)++ == IO_PIN_SHUTDOWN_LIMIT) {
2037 		slgt_irq_off(info, IRQ_CTS);
2038 		return;
2039 	}
2040 	info->icount.cts++;
2041 	wake_up_interruptible(&info->status_event_wait_q);
2042 	wake_up_interruptible(&info->event_wait_q);
2043 	info->pending_bh |= BH_STATUS;
2044 
2045 	if (tty_port_cts_enabled(&info->port)) {
2046 		if (info->port.tty) {
2047 			if (info->port.tty->hw_stopped) {
2048 				if (info->signals & SerialSignal_CTS) {
2049 		 			info->port.tty->hw_stopped = 0;
2050 					info->pending_bh |= BH_TRANSMIT;
2051 					return;
2052 				}
2053 			} else {
2054 				if (!(info->signals & SerialSignal_CTS))
2055 		 			info->port.tty->hw_stopped = 1;
2056 			}
2057 		}
2058 	}
2059 }
2060 
2061 static void dcd_change(struct slgt_info *info, unsigned short status)
2062 {
2063 	if (status & BIT1) {
2064 		info->signals |= SerialSignal_DCD;
2065 		info->input_signal_events.dcd_up++;
2066 	} else {
2067 		info->signals &= ~SerialSignal_DCD;
2068 		info->input_signal_events.dcd_down++;
2069 	}
2070 	DBGISR(("dcd_change %s signals=%04X\n", info->device_name, info->signals));
2071 	if ((info->dcd_chkcount)++ == IO_PIN_SHUTDOWN_LIMIT) {
2072 		slgt_irq_off(info, IRQ_DCD);
2073 		return;
2074 	}
2075 	info->icount.dcd++;
2076 #if SYNCLINK_GENERIC_HDLC
2077 	if (info->netcount) {
2078 		if (info->signals & SerialSignal_DCD)
2079 			netif_carrier_on(info->netdev);
2080 		else
2081 			netif_carrier_off(info->netdev);
2082 	}
2083 #endif
2084 	wake_up_interruptible(&info->status_event_wait_q);
2085 	wake_up_interruptible(&info->event_wait_q);
2086 	info->pending_bh |= BH_STATUS;
2087 
2088 	if (info->port.flags & ASYNC_CHECK_CD) {
2089 		if (info->signals & SerialSignal_DCD)
2090 			wake_up_interruptible(&info->port.open_wait);
2091 		else {
2092 			if (info->port.tty)
2093 				tty_hangup(info->port.tty);
2094 		}
2095 	}
2096 }
2097 
2098 static void ri_change(struct slgt_info *info, unsigned short status)
2099 {
2100 	if (status & BIT0) {
2101 		info->signals |= SerialSignal_RI;
2102 		info->input_signal_events.ri_up++;
2103 	} else {
2104 		info->signals &= ~SerialSignal_RI;
2105 		info->input_signal_events.ri_down++;
2106 	}
2107 	DBGISR(("ri_change %s signals=%04X\n", info->device_name, info->signals));
2108 	if ((info->ri_chkcount)++ == IO_PIN_SHUTDOWN_LIMIT) {
2109 		slgt_irq_off(info, IRQ_RI);
2110 		return;
2111 	}
2112 	info->icount.rng++;
2113 	wake_up_interruptible(&info->status_event_wait_q);
2114 	wake_up_interruptible(&info->event_wait_q);
2115 	info->pending_bh |= BH_STATUS;
2116 }
2117 
2118 static void isr_rxdata(struct slgt_info *info)
2119 {
2120 	unsigned int count = info->rbuf_fill_count;
2121 	unsigned int i = info->rbuf_fill_index;
2122 	unsigned short reg;
2123 
2124 	while (rd_reg16(info, SSR) & IRQ_RXDATA) {
2125 		reg = rd_reg16(info, RDR);
2126 		DBGISR(("isr_rxdata %s RDR=%04X\n", info->device_name, reg));
2127 		if (desc_complete(info->rbufs[i])) {
2128 			/* all buffers full */
2129 			rx_stop(info);
2130 			info->rx_restart = 1;
2131 			continue;
2132 		}
2133 		info->rbufs[i].buf[count++] = (unsigned char)reg;
2134 		/* async mode saves status byte to buffer for each data byte */
2135 		if (info->params.mode == MGSL_MODE_ASYNC)
2136 			info->rbufs[i].buf[count++] = (unsigned char)(reg >> 8);
2137 		if (count == info->rbuf_fill_level || (reg & BIT10)) {
2138 			/* buffer full or end of frame */
2139 			set_desc_count(info->rbufs[i], count);
2140 			set_desc_status(info->rbufs[i], BIT15 | (reg >> 8));
2141 			info->rbuf_fill_count = count = 0;
2142 			if (++i == info->rbuf_count)
2143 				i = 0;
2144 			info->pending_bh |= BH_RECEIVE;
2145 		}
2146 	}
2147 
2148 	info->rbuf_fill_index = i;
2149 	info->rbuf_fill_count = count;
2150 }
2151 
2152 static void isr_serial(struct slgt_info *info)
2153 {
2154 	unsigned short status = rd_reg16(info, SSR);
2155 
2156 	DBGISR(("%s isr_serial status=%04X\n", info->device_name, status));
2157 
2158 	wr_reg16(info, SSR, status); /* clear pending */
2159 
2160 	info->irq_occurred = true;
2161 
2162 	if (info->params.mode == MGSL_MODE_ASYNC) {
2163 		if (status & IRQ_TXIDLE) {
2164 			if (info->tx_active)
2165 				isr_txeom(info, status);
2166 		}
2167 		if (info->rx_pio && (status & IRQ_RXDATA))
2168 			isr_rxdata(info);
2169 		if ((status & IRQ_RXBREAK) && (status & RXBREAK)) {
2170 			info->icount.brk++;
2171 			/* process break detection if tty control allows */
2172 			if (info->port.tty) {
2173 				if (!(status & info->ignore_status_mask)) {
2174 					if (info->read_status_mask & MASK_BREAK) {
2175 						tty_insert_flip_char(&info->port, 0, TTY_BREAK);
2176 						if (info->port.flags & ASYNC_SAK)
2177 							do_SAK(info->port.tty);
2178 					}
2179 				}
2180 			}
2181 		}
2182 	} else {
2183 		if (status & (IRQ_TXIDLE + IRQ_TXUNDER))
2184 			isr_txeom(info, status);
2185 		if (info->rx_pio && (status & IRQ_RXDATA))
2186 			isr_rxdata(info);
2187 		if (status & IRQ_RXIDLE) {
2188 			if (status & RXIDLE)
2189 				info->icount.rxidle++;
2190 			else
2191 				info->icount.exithunt++;
2192 			wake_up_interruptible(&info->event_wait_q);
2193 		}
2194 
2195 		if (status & IRQ_RXOVER)
2196 			rx_start(info);
2197 	}
2198 
2199 	if (status & IRQ_DSR)
2200 		dsr_change(info, status);
2201 	if (status & IRQ_CTS)
2202 		cts_change(info, status);
2203 	if (status & IRQ_DCD)
2204 		dcd_change(info, status);
2205 	if (status & IRQ_RI)
2206 		ri_change(info, status);
2207 }
2208 
2209 static void isr_rdma(struct slgt_info *info)
2210 {
2211 	unsigned int status = rd_reg32(info, RDCSR);
2212 
2213 	DBGISR(("%s isr_rdma status=%08x\n", info->device_name, status));
2214 
2215 	/* RDCSR (rx DMA control/status)
2216 	 *
2217 	 * 31..07  reserved
2218 	 * 06      save status byte to DMA buffer
2219 	 * 05      error
2220 	 * 04      eol (end of list)
2221 	 * 03      eob (end of buffer)
2222 	 * 02      IRQ enable
2223 	 * 01      reset
2224 	 * 00      enable
2225 	 */
2226 	wr_reg32(info, RDCSR, status);	/* clear pending */
2227 
2228 	if (status & (BIT5 + BIT4)) {
2229 		DBGISR(("%s isr_rdma rx_restart=1\n", info->device_name));
2230 		info->rx_restart = true;
2231 	}
2232 	info->pending_bh |= BH_RECEIVE;
2233 }
2234 
2235 static void isr_tdma(struct slgt_info *info)
2236 {
2237 	unsigned int status = rd_reg32(info, TDCSR);
2238 
2239 	DBGISR(("%s isr_tdma status=%08x\n", info->device_name, status));
2240 
2241 	/* TDCSR (tx DMA control/status)
2242 	 *
2243 	 * 31..06  reserved
2244 	 * 05      error
2245 	 * 04      eol (end of list)
2246 	 * 03      eob (end of buffer)
2247 	 * 02      IRQ enable
2248 	 * 01      reset
2249 	 * 00      enable
2250 	 */
2251 	wr_reg32(info, TDCSR, status);	/* clear pending */
2252 
2253 	if (status & (BIT5 + BIT4 + BIT3)) {
2254 		// another transmit buffer has completed
2255 		// run bottom half to get more send data from user
2256 		info->pending_bh |= BH_TRANSMIT;
2257 	}
2258 }
2259 
2260 /*
2261  * return true if there are unsent tx DMA buffers, otherwise false
2262  *
2263  * if there are unsent buffers then info->tbuf_start
2264  * is set to index of first unsent buffer
2265  */
2266 static bool unsent_tbufs(struct slgt_info *info)
2267 {
2268 	unsigned int i = info->tbuf_current;
2269 	bool rc = false;
2270 
2271 	/*
2272 	 * search backwards from last loaded buffer (precedes tbuf_current)
2273 	 * for first unsent buffer (desc_count > 0)
2274 	 */
2275 
2276 	do {
2277 		if (i)
2278 			i--;
2279 		else
2280 			i = info->tbuf_count - 1;
2281 		if (!desc_count(info->tbufs[i]))
2282 			break;
2283 		info->tbuf_start = i;
2284 		rc = true;
2285 	} while (i != info->tbuf_current);
2286 
2287 	return rc;
2288 }
2289 
2290 static void isr_txeom(struct slgt_info *info, unsigned short status)
2291 {
2292 	DBGISR(("%s txeom status=%04x\n", info->device_name, status));
2293 
2294 	slgt_irq_off(info, IRQ_TXDATA + IRQ_TXIDLE + IRQ_TXUNDER);
2295 	tdma_reset(info);
2296 	if (status & IRQ_TXUNDER) {
2297 		unsigned short val = rd_reg16(info, TCR);
2298 		wr_reg16(info, TCR, (unsigned short)(val | BIT2)); /* set reset bit */
2299 		wr_reg16(info, TCR, val); /* clear reset bit */
2300 	}
2301 
2302 	if (info->tx_active) {
2303 		if (info->params.mode != MGSL_MODE_ASYNC) {
2304 			if (status & IRQ_TXUNDER)
2305 				info->icount.txunder++;
2306 			else if (status & IRQ_TXIDLE)
2307 				info->icount.txok++;
2308 		}
2309 
2310 		if (unsent_tbufs(info)) {
2311 			tx_start(info);
2312 			update_tx_timer(info);
2313 			return;
2314 		}
2315 		info->tx_active = false;
2316 
2317 		del_timer(&info->tx_timer);
2318 
2319 		if (info->params.mode != MGSL_MODE_ASYNC && info->drop_rts_on_tx_done) {
2320 			info->signals &= ~SerialSignal_RTS;
2321 			info->drop_rts_on_tx_done = false;
2322 			set_signals(info);
2323 		}
2324 
2325 #if SYNCLINK_GENERIC_HDLC
2326 		if (info->netcount)
2327 			hdlcdev_tx_done(info);
2328 		else
2329 #endif
2330 		{
2331 			if (info->port.tty && (info->port.tty->stopped || info->port.tty->hw_stopped)) {
2332 				tx_stop(info);
2333 				return;
2334 			}
2335 			info->pending_bh |= BH_TRANSMIT;
2336 		}
2337 	}
2338 }
2339 
2340 static void isr_gpio(struct slgt_info *info, unsigned int changed, unsigned int state)
2341 {
2342 	struct cond_wait *w, *prev;
2343 
2344 	/* wake processes waiting for specific transitions */
2345 	for (w = info->gpio_wait_q, prev = NULL ; w != NULL ; w = w->next) {
2346 		if (w->data & changed) {
2347 			w->data = state;
2348 			wake_up_interruptible(&w->q);
2349 			if (prev != NULL)
2350 				prev->next = w->next;
2351 			else
2352 				info->gpio_wait_q = w->next;
2353 		} else
2354 			prev = w;
2355 	}
2356 }
2357 
2358 /* interrupt service routine
2359  *
2360  * 	irq	interrupt number
2361  * 	dev_id	device ID supplied during interrupt registration
2362  */
2363 static irqreturn_t slgt_interrupt(int dummy, void *dev_id)
2364 {
2365 	struct slgt_info *info = dev_id;
2366 	unsigned int gsr;
2367 	unsigned int i;
2368 
2369 	DBGISR(("slgt_interrupt irq=%d entry\n", info->irq_level));
2370 
2371 	while((gsr = rd_reg32(info, GSR) & 0xffffff00)) {
2372 		DBGISR(("%s gsr=%08x\n", info->device_name, gsr));
2373 		info->irq_occurred = true;
2374 		for(i=0; i < info->port_count ; i++) {
2375 			if (info->port_array[i] == NULL)
2376 				continue;
2377 			spin_lock(&info->port_array[i]->lock);
2378 			if (gsr & (BIT8 << i))
2379 				isr_serial(info->port_array[i]);
2380 			if (gsr & (BIT16 << (i*2)))
2381 				isr_rdma(info->port_array[i]);
2382 			if (gsr & (BIT17 << (i*2)))
2383 				isr_tdma(info->port_array[i]);
2384 			spin_unlock(&info->port_array[i]->lock);
2385 		}
2386 	}
2387 
2388 	if (info->gpio_present) {
2389 		unsigned int state;
2390 		unsigned int changed;
2391 		spin_lock(&info->lock);
2392 		while ((changed = rd_reg32(info, IOSR)) != 0) {
2393 			DBGISR(("%s iosr=%08x\n", info->device_name, changed));
2394 			/* read latched state of GPIO signals */
2395 			state = rd_reg32(info, IOVR);
2396 			/* clear pending GPIO interrupt bits */
2397 			wr_reg32(info, IOSR, changed);
2398 			for (i=0 ; i < info->port_count ; i++) {
2399 				if (info->port_array[i] != NULL)
2400 					isr_gpio(info->port_array[i], changed, state);
2401 			}
2402 		}
2403 		spin_unlock(&info->lock);
2404 	}
2405 
2406 	for(i=0; i < info->port_count ; i++) {
2407 		struct slgt_info *port = info->port_array[i];
2408 		if (port == NULL)
2409 			continue;
2410 		spin_lock(&port->lock);
2411 		if ((port->port.count || port->netcount) &&
2412 		    port->pending_bh && !port->bh_running &&
2413 		    !port->bh_requested) {
2414 			DBGISR(("%s bh queued\n", port->device_name));
2415 			schedule_work(&port->task);
2416 			port->bh_requested = true;
2417 		}
2418 		spin_unlock(&port->lock);
2419 	}
2420 
2421 	DBGISR(("slgt_interrupt irq=%d exit\n", info->irq_level));
2422 	return IRQ_HANDLED;
2423 }
2424 
2425 static int startup(struct slgt_info *info)
2426 {
2427 	DBGINFO(("%s startup\n", info->device_name));
2428 
2429 	if (info->port.flags & ASYNC_INITIALIZED)
2430 		return 0;
2431 
2432 	if (!info->tx_buf) {
2433 		info->tx_buf = kmalloc(info->max_frame_size, GFP_KERNEL);
2434 		if (!info->tx_buf) {
2435 			DBGERR(("%s can't allocate tx buffer\n", info->device_name));
2436 			return -ENOMEM;
2437 		}
2438 	}
2439 
2440 	info->pending_bh = 0;
2441 
2442 	memset(&info->icount, 0, sizeof(info->icount));
2443 
2444 	/* program hardware for current parameters */
2445 	change_params(info);
2446 
2447 	if (info->port.tty)
2448 		clear_bit(TTY_IO_ERROR, &info->port.tty->flags);
2449 
2450 	info->port.flags |= ASYNC_INITIALIZED;
2451 
2452 	return 0;
2453 }
2454 
2455 /*
2456  *  called by close() and hangup() to shutdown hardware
2457  */
2458 static void shutdown(struct slgt_info *info)
2459 {
2460 	unsigned long flags;
2461 
2462 	if (!(info->port.flags & ASYNC_INITIALIZED))
2463 		return;
2464 
2465 	DBGINFO(("%s shutdown\n", info->device_name));
2466 
2467 	/* clear status wait queue because status changes */
2468 	/* can't happen after shutting down the hardware */
2469 	wake_up_interruptible(&info->status_event_wait_q);
2470 	wake_up_interruptible(&info->event_wait_q);
2471 
2472 	del_timer_sync(&info->tx_timer);
2473 	del_timer_sync(&info->rx_timer);
2474 
2475 	kfree(info->tx_buf);
2476 	info->tx_buf = NULL;
2477 
2478 	spin_lock_irqsave(&info->lock,flags);
2479 
2480 	tx_stop(info);
2481 	rx_stop(info);
2482 
2483 	slgt_irq_off(info, IRQ_ALL | IRQ_MASTER);
2484 
2485  	if (!info->port.tty || info->port.tty->termios.c_cflag & HUPCL) {
2486 		info->signals &= ~(SerialSignal_RTS | SerialSignal_DTR);
2487 		set_signals(info);
2488 	}
2489 
2490 	flush_cond_wait(&info->gpio_wait_q);
2491 
2492 	spin_unlock_irqrestore(&info->lock,flags);
2493 
2494 	if (info->port.tty)
2495 		set_bit(TTY_IO_ERROR, &info->port.tty->flags);
2496 
2497 	info->port.flags &= ~ASYNC_INITIALIZED;
2498 }
2499 
2500 static void program_hw(struct slgt_info *info)
2501 {
2502 	unsigned long flags;
2503 
2504 	spin_lock_irqsave(&info->lock,flags);
2505 
2506 	rx_stop(info);
2507 	tx_stop(info);
2508 
2509 	if (info->params.mode != MGSL_MODE_ASYNC ||
2510 	    info->netcount)
2511 		sync_mode(info);
2512 	else
2513 		async_mode(info);
2514 
2515 	set_signals(info);
2516 
2517 	info->dcd_chkcount = 0;
2518 	info->cts_chkcount = 0;
2519 	info->ri_chkcount = 0;
2520 	info->dsr_chkcount = 0;
2521 
2522 	slgt_irq_on(info, IRQ_DCD | IRQ_CTS | IRQ_DSR | IRQ_RI);
2523 	get_signals(info);
2524 
2525 	if (info->netcount ||
2526 	    (info->port.tty && info->port.tty->termios.c_cflag & CREAD))
2527 		rx_start(info);
2528 
2529 	spin_unlock_irqrestore(&info->lock,flags);
2530 }
2531 
2532 /*
2533  * reconfigure adapter based on new parameters
2534  */
2535 static void change_params(struct slgt_info *info)
2536 {
2537 	unsigned cflag;
2538 	int bits_per_char;
2539 
2540 	if (!info->port.tty)
2541 		return;
2542 	DBGINFO(("%s change_params\n", info->device_name));
2543 
2544 	cflag = info->port.tty->termios.c_cflag;
2545 
2546 	/* if B0 rate (hangup) specified then negate RTS and DTR */
2547 	/* otherwise assert RTS and DTR */
2548  	if (cflag & CBAUD)
2549 		info->signals |= SerialSignal_RTS | SerialSignal_DTR;
2550 	else
2551 		info->signals &= ~(SerialSignal_RTS | SerialSignal_DTR);
2552 
2553 	/* byte size and parity */
2554 
2555 	switch (cflag & CSIZE) {
2556 	case CS5: info->params.data_bits = 5; break;
2557 	case CS6: info->params.data_bits = 6; break;
2558 	case CS7: info->params.data_bits = 7; break;
2559 	case CS8: info->params.data_bits = 8; break;
2560 	default:  info->params.data_bits = 7; break;
2561 	}
2562 
2563 	info->params.stop_bits = (cflag & CSTOPB) ? 2 : 1;
2564 
2565 	if (cflag & PARENB)
2566 		info->params.parity = (cflag & PARODD) ? ASYNC_PARITY_ODD : ASYNC_PARITY_EVEN;
2567 	else
2568 		info->params.parity = ASYNC_PARITY_NONE;
2569 
2570 	/* calculate number of jiffies to transmit a full
2571 	 * FIFO (32 bytes) at specified data rate
2572 	 */
2573 	bits_per_char = info->params.data_bits +
2574 			info->params.stop_bits + 1;
2575 
2576 	info->params.data_rate = tty_get_baud_rate(info->port.tty);
2577 
2578 	if (info->params.data_rate) {
2579 		info->timeout = (32*HZ*bits_per_char) /
2580 				info->params.data_rate;
2581 	}
2582 	info->timeout += HZ/50;		/* Add .02 seconds of slop */
2583 
2584 	if (cflag & CRTSCTS)
2585 		info->port.flags |= ASYNC_CTS_FLOW;
2586 	else
2587 		info->port.flags &= ~ASYNC_CTS_FLOW;
2588 
2589 	if (cflag & CLOCAL)
2590 		info->port.flags &= ~ASYNC_CHECK_CD;
2591 	else
2592 		info->port.flags |= ASYNC_CHECK_CD;
2593 
2594 	/* process tty input control flags */
2595 
2596 	info->read_status_mask = IRQ_RXOVER;
2597 	if (I_INPCK(info->port.tty))
2598 		info->read_status_mask |= MASK_PARITY | MASK_FRAMING;
2599  	if (I_BRKINT(info->port.tty) || I_PARMRK(info->port.tty))
2600  		info->read_status_mask |= MASK_BREAK;
2601 	if (I_IGNPAR(info->port.tty))
2602 		info->ignore_status_mask |= MASK_PARITY | MASK_FRAMING;
2603 	if (I_IGNBRK(info->port.tty)) {
2604 		info->ignore_status_mask |= MASK_BREAK;
2605 		/* If ignoring parity and break indicators, ignore
2606 		 * overruns too.  (For real raw support).
2607 		 */
2608 		if (I_IGNPAR(info->port.tty))
2609 			info->ignore_status_mask |= MASK_OVERRUN;
2610 	}
2611 
2612 	program_hw(info);
2613 }
2614 
2615 static int get_stats(struct slgt_info *info, struct mgsl_icount __user *user_icount)
2616 {
2617 	DBGINFO(("%s get_stats\n",  info->device_name));
2618 	if (!user_icount) {
2619 		memset(&info->icount, 0, sizeof(info->icount));
2620 	} else {
2621 		if (copy_to_user(user_icount, &info->icount, sizeof(struct mgsl_icount)))
2622 			return -EFAULT;
2623 	}
2624 	return 0;
2625 }
2626 
2627 static int get_params(struct slgt_info *info, MGSL_PARAMS __user *user_params)
2628 {
2629 	DBGINFO(("%s get_params\n", info->device_name));
2630 	if (copy_to_user(user_params, &info->params, sizeof(MGSL_PARAMS)))
2631 		return -EFAULT;
2632 	return 0;
2633 }
2634 
2635 static int set_params(struct slgt_info *info, MGSL_PARAMS __user *new_params)
2636 {
2637  	unsigned long flags;
2638 	MGSL_PARAMS tmp_params;
2639 
2640 	DBGINFO(("%s set_params\n", info->device_name));
2641 	if (copy_from_user(&tmp_params, new_params, sizeof(MGSL_PARAMS)))
2642 		return -EFAULT;
2643 
2644 	spin_lock_irqsave(&info->lock, flags);
2645 	if (tmp_params.mode == MGSL_MODE_BASE_CLOCK)
2646 		info->base_clock = tmp_params.clock_speed;
2647 	else
2648 		memcpy(&info->params, &tmp_params, sizeof(MGSL_PARAMS));
2649 	spin_unlock_irqrestore(&info->lock, flags);
2650 
2651 	program_hw(info);
2652 
2653 	return 0;
2654 }
2655 
2656 static int get_txidle(struct slgt_info *info, int __user *idle_mode)
2657 {
2658 	DBGINFO(("%s get_txidle=%d\n", info->device_name, info->idle_mode));
2659 	if (put_user(info->idle_mode, idle_mode))
2660 		return -EFAULT;
2661 	return 0;
2662 }
2663 
2664 static int set_txidle(struct slgt_info *info, int idle_mode)
2665 {
2666  	unsigned long flags;
2667 	DBGINFO(("%s set_txidle(%d)\n", info->device_name, idle_mode));
2668 	spin_lock_irqsave(&info->lock,flags);
2669 	info->idle_mode = idle_mode;
2670 	if (info->params.mode != MGSL_MODE_ASYNC)
2671 		tx_set_idle(info);
2672 	spin_unlock_irqrestore(&info->lock,flags);
2673 	return 0;
2674 }
2675 
2676 static int tx_enable(struct slgt_info *info, int enable)
2677 {
2678  	unsigned long flags;
2679 	DBGINFO(("%s tx_enable(%d)\n", info->device_name, enable));
2680 	spin_lock_irqsave(&info->lock,flags);
2681 	if (enable) {
2682 		if (!info->tx_enabled)
2683 			tx_start(info);
2684 	} else {
2685 		if (info->tx_enabled)
2686 			tx_stop(info);
2687 	}
2688 	spin_unlock_irqrestore(&info->lock,flags);
2689 	return 0;
2690 }
2691 
2692 /*
2693  * abort transmit HDLC frame
2694  */
2695 static int tx_abort(struct slgt_info *info)
2696 {
2697  	unsigned long flags;
2698 	DBGINFO(("%s tx_abort\n", info->device_name));
2699 	spin_lock_irqsave(&info->lock,flags);
2700 	tdma_reset(info);
2701 	spin_unlock_irqrestore(&info->lock,flags);
2702 	return 0;
2703 }
2704 
2705 static int rx_enable(struct slgt_info *info, int enable)
2706 {
2707  	unsigned long flags;
2708 	unsigned int rbuf_fill_level;
2709 	DBGINFO(("%s rx_enable(%08x)\n", info->device_name, enable));
2710 	spin_lock_irqsave(&info->lock,flags);
2711 	/*
2712 	 * enable[31..16] = receive DMA buffer fill level
2713 	 * 0 = noop (leave fill level unchanged)
2714 	 * fill level must be multiple of 4 and <= buffer size
2715 	 */
2716 	rbuf_fill_level = ((unsigned int)enable) >> 16;
2717 	if (rbuf_fill_level) {
2718 		if ((rbuf_fill_level > DMABUFSIZE) || (rbuf_fill_level % 4)) {
2719 			spin_unlock_irqrestore(&info->lock, flags);
2720 			return -EINVAL;
2721 		}
2722 		info->rbuf_fill_level = rbuf_fill_level;
2723 		if (rbuf_fill_level < 128)
2724 			info->rx_pio = 1; /* PIO mode */
2725 		else
2726 			info->rx_pio = 0; /* DMA mode */
2727 		rx_stop(info); /* restart receiver to use new fill level */
2728 	}
2729 
2730 	/*
2731 	 * enable[1..0] = receiver enable command
2732 	 * 0 = disable
2733 	 * 1 = enable
2734 	 * 2 = enable or force hunt mode if already enabled
2735 	 */
2736 	enable &= 3;
2737 	if (enable) {
2738 		if (!info->rx_enabled)
2739 			rx_start(info);
2740 		else if (enable == 2) {
2741 			/* force hunt mode (write 1 to RCR[3]) */
2742 			wr_reg16(info, RCR, rd_reg16(info, RCR) | BIT3);
2743 		}
2744 	} else {
2745 		if (info->rx_enabled)
2746 			rx_stop(info);
2747 	}
2748 	spin_unlock_irqrestore(&info->lock,flags);
2749 	return 0;
2750 }
2751 
2752 /*
2753  *  wait for specified event to occur
2754  */
2755 static int wait_mgsl_event(struct slgt_info *info, int __user *mask_ptr)
2756 {
2757  	unsigned long flags;
2758 	int s;
2759 	int rc=0;
2760 	struct mgsl_icount cprev, cnow;
2761 	int events;
2762 	int mask;
2763 	struct	_input_signal_events oldsigs, newsigs;
2764 	DECLARE_WAITQUEUE(wait, current);
2765 
2766 	if (get_user(mask, mask_ptr))
2767 		return -EFAULT;
2768 
2769 	DBGINFO(("%s wait_mgsl_event(%d)\n", info->device_name, mask));
2770 
2771 	spin_lock_irqsave(&info->lock,flags);
2772 
2773 	/* return immediately if state matches requested events */
2774 	get_signals(info);
2775 	s = info->signals;
2776 
2777 	events = mask &
2778 		( ((s & SerialSignal_DSR) ? MgslEvent_DsrActive:MgslEvent_DsrInactive) +
2779  		  ((s & SerialSignal_DCD) ? MgslEvent_DcdActive:MgslEvent_DcdInactive) +
2780 		  ((s & SerialSignal_CTS) ? MgslEvent_CtsActive:MgslEvent_CtsInactive) +
2781 		  ((s & SerialSignal_RI)  ? MgslEvent_RiActive :MgslEvent_RiInactive) );
2782 	if (events) {
2783 		spin_unlock_irqrestore(&info->lock,flags);
2784 		goto exit;
2785 	}
2786 
2787 	/* save current irq counts */
2788 	cprev = info->icount;
2789 	oldsigs = info->input_signal_events;
2790 
2791 	/* enable hunt and idle irqs if needed */
2792 	if (mask & (MgslEvent_ExitHuntMode+MgslEvent_IdleReceived)) {
2793 		unsigned short val = rd_reg16(info, SCR);
2794 		if (!(val & IRQ_RXIDLE))
2795 			wr_reg16(info, SCR, (unsigned short)(val | IRQ_RXIDLE));
2796 	}
2797 
2798 	set_current_state(TASK_INTERRUPTIBLE);
2799 	add_wait_queue(&info->event_wait_q, &wait);
2800 
2801 	spin_unlock_irqrestore(&info->lock,flags);
2802 
2803 	for(;;) {
2804 		schedule();
2805 		if (signal_pending(current)) {
2806 			rc = -ERESTARTSYS;
2807 			break;
2808 		}
2809 
2810 		/* get current irq counts */
2811 		spin_lock_irqsave(&info->lock,flags);
2812 		cnow = info->icount;
2813 		newsigs = info->input_signal_events;
2814 		set_current_state(TASK_INTERRUPTIBLE);
2815 		spin_unlock_irqrestore(&info->lock,flags);
2816 
2817 		/* if no change, wait aborted for some reason */
2818 		if (newsigs.dsr_up   == oldsigs.dsr_up   &&
2819 		    newsigs.dsr_down == oldsigs.dsr_down &&
2820 		    newsigs.dcd_up   == oldsigs.dcd_up   &&
2821 		    newsigs.dcd_down == oldsigs.dcd_down &&
2822 		    newsigs.cts_up   == oldsigs.cts_up   &&
2823 		    newsigs.cts_down == oldsigs.cts_down &&
2824 		    newsigs.ri_up    == oldsigs.ri_up    &&
2825 		    newsigs.ri_down  == oldsigs.ri_down  &&
2826 		    cnow.exithunt    == cprev.exithunt   &&
2827 		    cnow.rxidle      == cprev.rxidle) {
2828 			rc = -EIO;
2829 			break;
2830 		}
2831 
2832 		events = mask &
2833 			( (newsigs.dsr_up   != oldsigs.dsr_up   ? MgslEvent_DsrActive:0)   +
2834 			  (newsigs.dsr_down != oldsigs.dsr_down ? MgslEvent_DsrInactive:0) +
2835 			  (newsigs.dcd_up   != oldsigs.dcd_up   ? MgslEvent_DcdActive:0)   +
2836 			  (newsigs.dcd_down != oldsigs.dcd_down ? MgslEvent_DcdInactive:0) +
2837 			  (newsigs.cts_up   != oldsigs.cts_up   ? MgslEvent_CtsActive:0)   +
2838 			  (newsigs.cts_down != oldsigs.cts_down ? MgslEvent_CtsInactive:0) +
2839 			  (newsigs.ri_up    != oldsigs.ri_up    ? MgslEvent_RiActive:0)    +
2840 			  (newsigs.ri_down  != oldsigs.ri_down  ? MgslEvent_RiInactive:0)  +
2841 			  (cnow.exithunt    != cprev.exithunt   ? MgslEvent_ExitHuntMode:0) +
2842 			  (cnow.rxidle      != cprev.rxidle     ? MgslEvent_IdleReceived:0) );
2843 		if (events)
2844 			break;
2845 
2846 		cprev = cnow;
2847 		oldsigs = newsigs;
2848 	}
2849 
2850 	remove_wait_queue(&info->event_wait_q, &wait);
2851 	set_current_state(TASK_RUNNING);
2852 
2853 
2854 	if (mask & (MgslEvent_ExitHuntMode + MgslEvent_IdleReceived)) {
2855 		spin_lock_irqsave(&info->lock,flags);
2856 		if (!waitqueue_active(&info->event_wait_q)) {
2857 			/* disable enable exit hunt mode/idle rcvd IRQs */
2858 			wr_reg16(info, SCR,
2859 				(unsigned short)(rd_reg16(info, SCR) & ~IRQ_RXIDLE));
2860 		}
2861 		spin_unlock_irqrestore(&info->lock,flags);
2862 	}
2863 exit:
2864 	if (rc == 0)
2865 		rc = put_user(events, mask_ptr);
2866 	return rc;
2867 }
2868 
2869 static int get_interface(struct slgt_info *info, int __user *if_mode)
2870 {
2871 	DBGINFO(("%s get_interface=%x\n", info->device_name, info->if_mode));
2872 	if (put_user(info->if_mode, if_mode))
2873 		return -EFAULT;
2874 	return 0;
2875 }
2876 
2877 static int set_interface(struct slgt_info *info, int if_mode)
2878 {
2879  	unsigned long flags;
2880 	unsigned short val;
2881 
2882 	DBGINFO(("%s set_interface=%x)\n", info->device_name, if_mode));
2883 	spin_lock_irqsave(&info->lock,flags);
2884 	info->if_mode = if_mode;
2885 
2886 	msc_set_vcr(info);
2887 
2888 	/* TCR (tx control) 07  1=RTS driver control */
2889 	val = rd_reg16(info, TCR);
2890 	if (info->if_mode & MGSL_INTERFACE_RTS_EN)
2891 		val |= BIT7;
2892 	else
2893 		val &= ~BIT7;
2894 	wr_reg16(info, TCR, val);
2895 
2896 	spin_unlock_irqrestore(&info->lock,flags);
2897 	return 0;
2898 }
2899 
2900 static int get_xsync(struct slgt_info *info, int __user *xsync)
2901 {
2902 	DBGINFO(("%s get_xsync=%x\n", info->device_name, info->xsync));
2903 	if (put_user(info->xsync, xsync))
2904 		return -EFAULT;
2905 	return 0;
2906 }
2907 
2908 /*
2909  * set extended sync pattern (1 to 4 bytes) for extended sync mode
2910  *
2911  * sync pattern is contained in least significant bytes of value
2912  * most significant byte of sync pattern is oldest (1st sent/detected)
2913  */
2914 static int set_xsync(struct slgt_info *info, int xsync)
2915 {
2916 	unsigned long flags;
2917 
2918 	DBGINFO(("%s set_xsync=%x)\n", info->device_name, xsync));
2919 	spin_lock_irqsave(&info->lock, flags);
2920 	info->xsync = xsync;
2921 	wr_reg32(info, XSR, xsync);
2922 	spin_unlock_irqrestore(&info->lock, flags);
2923 	return 0;
2924 }
2925 
2926 static int get_xctrl(struct slgt_info *info, int __user *xctrl)
2927 {
2928 	DBGINFO(("%s get_xctrl=%x\n", info->device_name, info->xctrl));
2929 	if (put_user(info->xctrl, xctrl))
2930 		return -EFAULT;
2931 	return 0;
2932 }
2933 
2934 /*
2935  * set extended control options
2936  *
2937  * xctrl[31:19] reserved, must be zero
2938  * xctrl[18:17] extended sync pattern length in bytes
2939  *              00 = 1 byte  in xsr[7:0]
2940  *              01 = 2 bytes in xsr[15:0]
2941  *              10 = 3 bytes in xsr[23:0]
2942  *              11 = 4 bytes in xsr[31:0]
2943  * xctrl[16]    1 = enable terminal count, 0=disabled
2944  * xctrl[15:0]  receive terminal count for fixed length packets
2945  *              value is count minus one (0 = 1 byte packet)
2946  *              when terminal count is reached, receiver
2947  *              automatically returns to hunt mode and receive
2948  *              FIFO contents are flushed to DMA buffers with
2949  *              end of frame (EOF) status
2950  */
2951 static int set_xctrl(struct slgt_info *info, int xctrl)
2952 {
2953 	unsigned long flags;
2954 
2955 	DBGINFO(("%s set_xctrl=%x)\n", info->device_name, xctrl));
2956 	spin_lock_irqsave(&info->lock, flags);
2957 	info->xctrl = xctrl;
2958 	wr_reg32(info, XCR, xctrl);
2959 	spin_unlock_irqrestore(&info->lock, flags);
2960 	return 0;
2961 }
2962 
2963 /*
2964  * set general purpose IO pin state and direction
2965  *
2966  * user_gpio fields:
2967  * state   each bit indicates a pin state
2968  * smask   set bit indicates pin state to set
2969  * dir     each bit indicates a pin direction (0=input, 1=output)
2970  * dmask   set bit indicates pin direction to set
2971  */
2972 static int set_gpio(struct slgt_info *info, struct gpio_desc __user *user_gpio)
2973 {
2974  	unsigned long flags;
2975 	struct gpio_desc gpio;
2976 	__u32 data;
2977 
2978 	if (!info->gpio_present)
2979 		return -EINVAL;
2980 	if (copy_from_user(&gpio, user_gpio, sizeof(gpio)))
2981 		return -EFAULT;
2982 	DBGINFO(("%s set_gpio state=%08x smask=%08x dir=%08x dmask=%08x\n",
2983 		 info->device_name, gpio.state, gpio.smask,
2984 		 gpio.dir, gpio.dmask));
2985 
2986 	spin_lock_irqsave(&info->port_array[0]->lock, flags);
2987 	if (gpio.dmask) {
2988 		data = rd_reg32(info, IODR);
2989 		data |= gpio.dmask & gpio.dir;
2990 		data &= ~(gpio.dmask & ~gpio.dir);
2991 		wr_reg32(info, IODR, data);
2992 	}
2993 	if (gpio.smask) {
2994 		data = rd_reg32(info, IOVR);
2995 		data |= gpio.smask & gpio.state;
2996 		data &= ~(gpio.smask & ~gpio.state);
2997 		wr_reg32(info, IOVR, data);
2998 	}
2999 	spin_unlock_irqrestore(&info->port_array[0]->lock, flags);
3000 
3001 	return 0;
3002 }
3003 
3004 /*
3005  * get general purpose IO pin state and direction
3006  */
3007 static int get_gpio(struct slgt_info *info, struct gpio_desc __user *user_gpio)
3008 {
3009 	struct gpio_desc gpio;
3010 	if (!info->gpio_present)
3011 		return -EINVAL;
3012 	gpio.state = rd_reg32(info, IOVR);
3013 	gpio.smask = 0xffffffff;
3014 	gpio.dir   = rd_reg32(info, IODR);
3015 	gpio.dmask = 0xffffffff;
3016 	if (copy_to_user(user_gpio, &gpio, sizeof(gpio)))
3017 		return -EFAULT;
3018 	DBGINFO(("%s get_gpio state=%08x dir=%08x\n",
3019 		 info->device_name, gpio.state, gpio.dir));
3020 	return 0;
3021 }
3022 
3023 /*
3024  * conditional wait facility
3025  */
3026 static void init_cond_wait(struct cond_wait *w, unsigned int data)
3027 {
3028 	init_waitqueue_head(&w->q);
3029 	init_waitqueue_entry(&w->wait, current);
3030 	w->data = data;
3031 }
3032 
3033 static void add_cond_wait(struct cond_wait **head, struct cond_wait *w)
3034 {
3035 	set_current_state(TASK_INTERRUPTIBLE);
3036 	add_wait_queue(&w->q, &w->wait);
3037 	w->next = *head;
3038 	*head = w;
3039 }
3040 
3041 static void remove_cond_wait(struct cond_wait **head, struct cond_wait *cw)
3042 {
3043 	struct cond_wait *w, *prev;
3044 	remove_wait_queue(&cw->q, &cw->wait);
3045 	set_current_state(TASK_RUNNING);
3046 	for (w = *head, prev = NULL ; w != NULL ; prev = w, w = w->next) {
3047 		if (w == cw) {
3048 			if (prev != NULL)
3049 				prev->next = w->next;
3050 			else
3051 				*head = w->next;
3052 			break;
3053 		}
3054 	}
3055 }
3056 
3057 static void flush_cond_wait(struct cond_wait **head)
3058 {
3059 	while (*head != NULL) {
3060 		wake_up_interruptible(&(*head)->q);
3061 		*head = (*head)->next;
3062 	}
3063 }
3064 
3065 /*
3066  * wait for general purpose I/O pin(s) to enter specified state
3067  *
3068  * user_gpio fields:
3069  * state - bit indicates target pin state
3070  * smask - set bit indicates watched pin
3071  *
3072  * The wait ends when at least one watched pin enters the specified
3073  * state. When 0 (no error) is returned, user_gpio->state is set to the
3074  * state of all GPIO pins when the wait ends.
3075  *
3076  * Note: Each pin may be a dedicated input, dedicated output, or
3077  * configurable input/output. The number and configuration of pins
3078  * varies with the specific adapter model. Only input pins (dedicated
3079  * or configured) can be monitored with this function.
3080  */
3081 static int wait_gpio(struct slgt_info *info, struct gpio_desc __user *user_gpio)
3082 {
3083  	unsigned long flags;
3084 	int rc = 0;
3085 	struct gpio_desc gpio;
3086 	struct cond_wait wait;
3087 	u32 state;
3088 
3089 	if (!info->gpio_present)
3090 		return -EINVAL;
3091 	if (copy_from_user(&gpio, user_gpio, sizeof(gpio)))
3092 		return -EFAULT;
3093 	DBGINFO(("%s wait_gpio() state=%08x smask=%08x\n",
3094 		 info->device_name, gpio.state, gpio.smask));
3095 	/* ignore output pins identified by set IODR bit */
3096 	if ((gpio.smask &= ~rd_reg32(info, IODR)) == 0)
3097 		return -EINVAL;
3098 	init_cond_wait(&wait, gpio.smask);
3099 
3100 	spin_lock_irqsave(&info->port_array[0]->lock, flags);
3101 	/* enable interrupts for watched pins */
3102 	wr_reg32(info, IOER, rd_reg32(info, IOER) | gpio.smask);
3103 	/* get current pin states */
3104 	state = rd_reg32(info, IOVR);
3105 
3106 	if (gpio.smask & ~(state ^ gpio.state)) {
3107 		/* already in target state */
3108 		gpio.state = state;
3109 	} else {
3110 		/* wait for target state */
3111 		add_cond_wait(&info->gpio_wait_q, &wait);
3112 		spin_unlock_irqrestore(&info->port_array[0]->lock, flags);
3113 		schedule();
3114 		if (signal_pending(current))
3115 			rc = -ERESTARTSYS;
3116 		else
3117 			gpio.state = wait.data;
3118 		spin_lock_irqsave(&info->port_array[0]->lock, flags);
3119 		remove_cond_wait(&info->gpio_wait_q, &wait);
3120 	}
3121 
3122 	/* disable all GPIO interrupts if no waiting processes */
3123 	if (info->gpio_wait_q == NULL)
3124 		wr_reg32(info, IOER, 0);
3125 	spin_unlock_irqrestore(&info->port_array[0]->lock, flags);
3126 
3127 	if ((rc == 0) && copy_to_user(user_gpio, &gpio, sizeof(gpio)))
3128 		rc = -EFAULT;
3129 	return rc;
3130 }
3131 
3132 static int modem_input_wait(struct slgt_info *info,int arg)
3133 {
3134  	unsigned long flags;
3135 	int rc;
3136 	struct mgsl_icount cprev, cnow;
3137 	DECLARE_WAITQUEUE(wait, current);
3138 
3139 	/* save current irq counts */
3140 	spin_lock_irqsave(&info->lock,flags);
3141 	cprev = info->icount;
3142 	add_wait_queue(&info->status_event_wait_q, &wait);
3143 	set_current_state(TASK_INTERRUPTIBLE);
3144 	spin_unlock_irqrestore(&info->lock,flags);
3145 
3146 	for(;;) {
3147 		schedule();
3148 		if (signal_pending(current)) {
3149 			rc = -ERESTARTSYS;
3150 			break;
3151 		}
3152 
3153 		/* get new irq counts */
3154 		spin_lock_irqsave(&info->lock,flags);
3155 		cnow = info->icount;
3156 		set_current_state(TASK_INTERRUPTIBLE);
3157 		spin_unlock_irqrestore(&info->lock,flags);
3158 
3159 		/* if no change, wait aborted for some reason */
3160 		if (cnow.rng == cprev.rng && cnow.dsr == cprev.dsr &&
3161 		    cnow.dcd == cprev.dcd && cnow.cts == cprev.cts) {
3162 			rc = -EIO;
3163 			break;
3164 		}
3165 
3166 		/* check for change in caller specified modem input */
3167 		if ((arg & TIOCM_RNG && cnow.rng != cprev.rng) ||
3168 		    (arg & TIOCM_DSR && cnow.dsr != cprev.dsr) ||
3169 		    (arg & TIOCM_CD  && cnow.dcd != cprev.dcd) ||
3170 		    (arg & TIOCM_CTS && cnow.cts != cprev.cts)) {
3171 			rc = 0;
3172 			break;
3173 		}
3174 
3175 		cprev = cnow;
3176 	}
3177 	remove_wait_queue(&info->status_event_wait_q, &wait);
3178 	set_current_state(TASK_RUNNING);
3179 	return rc;
3180 }
3181 
3182 /*
3183  *  return state of serial control and status signals
3184  */
3185 static int tiocmget(struct tty_struct *tty)
3186 {
3187 	struct slgt_info *info = tty->driver_data;
3188 	unsigned int result;
3189  	unsigned long flags;
3190 
3191 	spin_lock_irqsave(&info->lock,flags);
3192  	get_signals(info);
3193 	spin_unlock_irqrestore(&info->lock,flags);
3194 
3195 	result = ((info->signals & SerialSignal_RTS) ? TIOCM_RTS:0) +
3196 		((info->signals & SerialSignal_DTR) ? TIOCM_DTR:0) +
3197 		((info->signals & SerialSignal_DCD) ? TIOCM_CAR:0) +
3198 		((info->signals & SerialSignal_RI)  ? TIOCM_RNG:0) +
3199 		((info->signals & SerialSignal_DSR) ? TIOCM_DSR:0) +
3200 		((info->signals & SerialSignal_CTS) ? TIOCM_CTS:0);
3201 
3202 	DBGINFO(("%s tiocmget value=%08X\n", info->device_name, result));
3203 	return result;
3204 }
3205 
3206 /*
3207  * set modem control signals (DTR/RTS)
3208  *
3209  * 	cmd	signal command: TIOCMBIS = set bit TIOCMBIC = clear bit
3210  *		TIOCMSET = set/clear signal values
3211  * 	value	bit mask for command
3212  */
3213 static int tiocmset(struct tty_struct *tty,
3214 		    unsigned int set, unsigned int clear)
3215 {
3216 	struct slgt_info *info = tty->driver_data;
3217  	unsigned long flags;
3218 
3219 	DBGINFO(("%s tiocmset(%x,%x)\n", info->device_name, set, clear));
3220 
3221 	if (set & TIOCM_RTS)
3222 		info->signals |= SerialSignal_RTS;
3223 	if (set & TIOCM_DTR)
3224 		info->signals |= SerialSignal_DTR;
3225 	if (clear & TIOCM_RTS)
3226 		info->signals &= ~SerialSignal_RTS;
3227 	if (clear & TIOCM_DTR)
3228 		info->signals &= ~SerialSignal_DTR;
3229 
3230 	spin_lock_irqsave(&info->lock,flags);
3231  	set_signals(info);
3232 	spin_unlock_irqrestore(&info->lock,flags);
3233 	return 0;
3234 }
3235 
3236 static int carrier_raised(struct tty_port *port)
3237 {
3238 	unsigned long flags;
3239 	struct slgt_info *info = container_of(port, struct slgt_info, port);
3240 
3241 	spin_lock_irqsave(&info->lock,flags);
3242  	get_signals(info);
3243 	spin_unlock_irqrestore(&info->lock,flags);
3244 	return (info->signals & SerialSignal_DCD) ? 1 : 0;
3245 }
3246 
3247 static void dtr_rts(struct tty_port *port, int on)
3248 {
3249 	unsigned long flags;
3250 	struct slgt_info *info = container_of(port, struct slgt_info, port);
3251 
3252 	spin_lock_irqsave(&info->lock,flags);
3253 	if (on)
3254 		info->signals |= SerialSignal_RTS | SerialSignal_DTR;
3255 	else
3256 		info->signals &= ~(SerialSignal_RTS | SerialSignal_DTR);
3257  	set_signals(info);
3258 	spin_unlock_irqrestore(&info->lock,flags);
3259 }
3260 
3261 
3262 /*
3263  *  block current process until the device is ready to open
3264  */
3265 static int block_til_ready(struct tty_struct *tty, struct file *filp,
3266 			   struct slgt_info *info)
3267 {
3268 	DECLARE_WAITQUEUE(wait, current);
3269 	int		retval;
3270 	bool		do_clocal = false;
3271 	unsigned long	flags;
3272 	int		cd;
3273 	struct tty_port *port = &info->port;
3274 
3275 	DBGINFO(("%s block_til_ready\n", tty->driver->name));
3276 
3277 	if (filp->f_flags & O_NONBLOCK || tty->flags & (1 << TTY_IO_ERROR)){
3278 		/* nonblock mode is set or port is not enabled */
3279 		port->flags |= ASYNC_NORMAL_ACTIVE;
3280 		return 0;
3281 	}
3282 
3283 	if (tty->termios.c_cflag & CLOCAL)
3284 		do_clocal = true;
3285 
3286 	/* Wait for carrier detect and the line to become
3287 	 * free (i.e., not in use by the callout).  While we are in
3288 	 * this loop, port->count is dropped by one, so that
3289 	 * close() knows when to free things.  We restore it upon
3290 	 * exit, either normal or abnormal.
3291 	 */
3292 
3293 	retval = 0;
3294 	add_wait_queue(&port->open_wait, &wait);
3295 
3296 	spin_lock_irqsave(&info->lock, flags);
3297 	port->count--;
3298 	spin_unlock_irqrestore(&info->lock, flags);
3299 	port->blocked_open++;
3300 
3301 	while (1) {
3302 		if (C_BAUD(tty) && test_bit(ASYNCB_INITIALIZED, &port->flags))
3303 			tty_port_raise_dtr_rts(port);
3304 
3305 		set_current_state(TASK_INTERRUPTIBLE);
3306 
3307 		if (tty_hung_up_p(filp) || !(port->flags & ASYNC_INITIALIZED)){
3308 			retval = (port->flags & ASYNC_HUP_NOTIFY) ?
3309 					-EAGAIN : -ERESTARTSYS;
3310 			break;
3311 		}
3312 
3313 		cd = tty_port_carrier_raised(port);
3314 		if (do_clocal || cd)
3315 			break;
3316 
3317 		if (signal_pending(current)) {
3318 			retval = -ERESTARTSYS;
3319 			break;
3320 		}
3321 
3322 		DBGINFO(("%s block_til_ready wait\n", tty->driver->name));
3323 		tty_unlock(tty);
3324 		schedule();
3325 		tty_lock(tty);
3326 	}
3327 
3328 	set_current_state(TASK_RUNNING);
3329 	remove_wait_queue(&port->open_wait, &wait);
3330 
3331 	if (!tty_hung_up_p(filp))
3332 		port->count++;
3333 	port->blocked_open--;
3334 
3335 	if (!retval)
3336 		port->flags |= ASYNC_NORMAL_ACTIVE;
3337 
3338 	DBGINFO(("%s block_til_ready ready, rc=%d\n", tty->driver->name, retval));
3339 	return retval;
3340 }
3341 
3342 /*
3343  * allocate buffers used for calling line discipline receive_buf
3344  * directly in synchronous mode
3345  * note: add 5 bytes to max frame size to allow appending
3346  * 32-bit CRC and status byte when configured to do so
3347  */
3348 static int alloc_tmp_rbuf(struct slgt_info *info)
3349 {
3350 	info->tmp_rbuf = kmalloc(info->max_frame_size + 5, GFP_KERNEL);
3351 	if (info->tmp_rbuf == NULL)
3352 		return -ENOMEM;
3353 	/* unused flag buffer to satisfy receive_buf calling interface */
3354 	info->flag_buf = kzalloc(info->max_frame_size + 5, GFP_KERNEL);
3355 	if (!info->flag_buf) {
3356 		kfree(info->tmp_rbuf);
3357 		info->tmp_rbuf = NULL;
3358 		return -ENOMEM;
3359 	}
3360 	return 0;
3361 }
3362 
3363 static void free_tmp_rbuf(struct slgt_info *info)
3364 {
3365 	kfree(info->tmp_rbuf);
3366 	info->tmp_rbuf = NULL;
3367 	kfree(info->flag_buf);
3368 	info->flag_buf = NULL;
3369 }
3370 
3371 /*
3372  * allocate DMA descriptor lists.
3373  */
3374 static int alloc_desc(struct slgt_info *info)
3375 {
3376 	unsigned int i;
3377 	unsigned int pbufs;
3378 
3379 	/* allocate memory to hold descriptor lists */
3380 	info->bufs = pci_zalloc_consistent(info->pdev, DESC_LIST_SIZE,
3381 					   &info->bufs_dma_addr);
3382 	if (info->bufs == NULL)
3383 		return -ENOMEM;
3384 
3385 	info->rbufs = (struct slgt_desc*)info->bufs;
3386 	info->tbufs = ((struct slgt_desc*)info->bufs) + info->rbuf_count;
3387 
3388 	pbufs = (unsigned int)info->bufs_dma_addr;
3389 
3390 	/*
3391 	 * Build circular lists of descriptors
3392 	 */
3393 
3394 	for (i=0; i < info->rbuf_count; i++) {
3395 		/* physical address of this descriptor */
3396 		info->rbufs[i].pdesc = pbufs + (i * sizeof(struct slgt_desc));
3397 
3398 		/* physical address of next descriptor */
3399 		if (i == info->rbuf_count - 1)
3400 			info->rbufs[i].next = cpu_to_le32(pbufs);
3401 		else
3402 			info->rbufs[i].next = cpu_to_le32(pbufs + ((i+1) * sizeof(struct slgt_desc)));
3403 		set_desc_count(info->rbufs[i], DMABUFSIZE);
3404 	}
3405 
3406 	for (i=0; i < info->tbuf_count; i++) {
3407 		/* physical address of this descriptor */
3408 		info->tbufs[i].pdesc = pbufs + ((info->rbuf_count + i) * sizeof(struct slgt_desc));
3409 
3410 		/* physical address of next descriptor */
3411 		if (i == info->tbuf_count - 1)
3412 			info->tbufs[i].next = cpu_to_le32(pbufs + info->rbuf_count * sizeof(struct slgt_desc));
3413 		else
3414 			info->tbufs[i].next = cpu_to_le32(pbufs + ((info->rbuf_count + i + 1) * sizeof(struct slgt_desc)));
3415 	}
3416 
3417 	return 0;
3418 }
3419 
3420 static void free_desc(struct slgt_info *info)
3421 {
3422 	if (info->bufs != NULL) {
3423 		pci_free_consistent(info->pdev, DESC_LIST_SIZE, info->bufs, info->bufs_dma_addr);
3424 		info->bufs  = NULL;
3425 		info->rbufs = NULL;
3426 		info->tbufs = NULL;
3427 	}
3428 }
3429 
3430 static int alloc_bufs(struct slgt_info *info, struct slgt_desc *bufs, int count)
3431 {
3432 	int i;
3433 	for (i=0; i < count; i++) {
3434 		if ((bufs[i].buf = pci_alloc_consistent(info->pdev, DMABUFSIZE, &bufs[i].buf_dma_addr)) == NULL)
3435 			return -ENOMEM;
3436 		bufs[i].pbuf  = cpu_to_le32((unsigned int)bufs[i].buf_dma_addr);
3437 	}
3438 	return 0;
3439 }
3440 
3441 static void free_bufs(struct slgt_info *info, struct slgt_desc *bufs, int count)
3442 {
3443 	int i;
3444 	for (i=0; i < count; i++) {
3445 		if (bufs[i].buf == NULL)
3446 			continue;
3447 		pci_free_consistent(info->pdev, DMABUFSIZE, bufs[i].buf, bufs[i].buf_dma_addr);
3448 		bufs[i].buf = NULL;
3449 	}
3450 }
3451 
3452 static int alloc_dma_bufs(struct slgt_info *info)
3453 {
3454 	info->rbuf_count = 32;
3455 	info->tbuf_count = 32;
3456 
3457 	if (alloc_desc(info) < 0 ||
3458 	    alloc_bufs(info, info->rbufs, info->rbuf_count) < 0 ||
3459 	    alloc_bufs(info, info->tbufs, info->tbuf_count) < 0 ||
3460 	    alloc_tmp_rbuf(info) < 0) {
3461 		DBGERR(("%s DMA buffer alloc fail\n", info->device_name));
3462 		return -ENOMEM;
3463 	}
3464 	reset_rbufs(info);
3465 	return 0;
3466 }
3467 
3468 static void free_dma_bufs(struct slgt_info *info)
3469 {
3470 	if (info->bufs) {
3471 		free_bufs(info, info->rbufs, info->rbuf_count);
3472 		free_bufs(info, info->tbufs, info->tbuf_count);
3473 		free_desc(info);
3474 	}
3475 	free_tmp_rbuf(info);
3476 }
3477 
3478 static int claim_resources(struct slgt_info *info)
3479 {
3480 	if (request_mem_region(info->phys_reg_addr, SLGT_REG_SIZE, "synclink_gt") == NULL) {
3481 		DBGERR(("%s reg addr conflict, addr=%08X\n",
3482 			info->device_name, info->phys_reg_addr));
3483 		info->init_error = DiagStatus_AddressConflict;
3484 		goto errout;
3485 	}
3486 	else
3487 		info->reg_addr_requested = true;
3488 
3489 	info->reg_addr = ioremap_nocache(info->phys_reg_addr, SLGT_REG_SIZE);
3490 	if (!info->reg_addr) {
3491 		DBGERR(("%s can't map device registers, addr=%08X\n",
3492 			info->device_name, info->phys_reg_addr));
3493 		info->init_error = DiagStatus_CantAssignPciResources;
3494 		goto errout;
3495 	}
3496 	return 0;
3497 
3498 errout:
3499 	release_resources(info);
3500 	return -ENODEV;
3501 }
3502 
3503 static void release_resources(struct slgt_info *info)
3504 {
3505 	if (info->irq_requested) {
3506 		free_irq(info->irq_level, info);
3507 		info->irq_requested = false;
3508 	}
3509 
3510 	if (info->reg_addr_requested) {
3511 		release_mem_region(info->phys_reg_addr, SLGT_REG_SIZE);
3512 		info->reg_addr_requested = false;
3513 	}
3514 
3515 	if (info->reg_addr) {
3516 		iounmap(info->reg_addr);
3517 		info->reg_addr = NULL;
3518 	}
3519 }
3520 
3521 /* Add the specified device instance data structure to the
3522  * global linked list of devices and increment the device count.
3523  */
3524 static void add_device(struct slgt_info *info)
3525 {
3526 	char *devstr;
3527 
3528 	info->next_device = NULL;
3529 	info->line = slgt_device_count;
3530 	sprintf(info->device_name, "%s%d", tty_dev_prefix, info->line);
3531 
3532 	if (info->line < MAX_DEVICES) {
3533 		if (maxframe[info->line])
3534 			info->max_frame_size = maxframe[info->line];
3535 	}
3536 
3537 	slgt_device_count++;
3538 
3539 	if (!slgt_device_list)
3540 		slgt_device_list = info;
3541 	else {
3542 		struct slgt_info *current_dev = slgt_device_list;
3543 		while(current_dev->next_device)
3544 			current_dev = current_dev->next_device;
3545 		current_dev->next_device = info;
3546 	}
3547 
3548 	if (info->max_frame_size < 4096)
3549 		info->max_frame_size = 4096;
3550 	else if (info->max_frame_size > 65535)
3551 		info->max_frame_size = 65535;
3552 
3553 	switch(info->pdev->device) {
3554 	case SYNCLINK_GT_DEVICE_ID:
3555 		devstr = "GT";
3556 		break;
3557 	case SYNCLINK_GT2_DEVICE_ID:
3558 		devstr = "GT2";
3559 		break;
3560 	case SYNCLINK_GT4_DEVICE_ID:
3561 		devstr = "GT4";
3562 		break;
3563 	case SYNCLINK_AC_DEVICE_ID:
3564 		devstr = "AC";
3565 		info->params.mode = MGSL_MODE_ASYNC;
3566 		break;
3567 	default:
3568 		devstr = "(unknown model)";
3569 	}
3570 	printk("SyncLink %s %s IO=%08x IRQ=%d MaxFrameSize=%u\n",
3571 		devstr, info->device_name, info->phys_reg_addr,
3572 		info->irq_level, info->max_frame_size);
3573 
3574 #if SYNCLINK_GENERIC_HDLC
3575 	hdlcdev_init(info);
3576 #endif
3577 }
3578 
3579 static const struct tty_port_operations slgt_port_ops = {
3580 	.carrier_raised = carrier_raised,
3581 	.dtr_rts = dtr_rts,
3582 };
3583 
3584 /*
3585  *  allocate device instance structure, return NULL on failure
3586  */
3587 static struct slgt_info *alloc_dev(int adapter_num, int port_num, struct pci_dev *pdev)
3588 {
3589 	struct slgt_info *info;
3590 
3591 	info = kzalloc(sizeof(struct slgt_info), GFP_KERNEL);
3592 
3593 	if (!info) {
3594 		DBGERR(("%s device alloc failed adapter=%d port=%d\n",
3595 			driver_name, adapter_num, port_num));
3596 	} else {
3597 		tty_port_init(&info->port);
3598 		info->port.ops = &slgt_port_ops;
3599 		info->magic = MGSL_MAGIC;
3600 		INIT_WORK(&info->task, bh_handler);
3601 		info->max_frame_size = 4096;
3602 		info->base_clock = 14745600;
3603 		info->rbuf_fill_level = DMABUFSIZE;
3604 		info->port.close_delay = 5*HZ/10;
3605 		info->port.closing_wait = 30*HZ;
3606 		init_waitqueue_head(&info->status_event_wait_q);
3607 		init_waitqueue_head(&info->event_wait_q);
3608 		spin_lock_init(&info->netlock);
3609 		memcpy(&info->params,&default_params,sizeof(MGSL_PARAMS));
3610 		info->idle_mode = HDLC_TXIDLE_FLAGS;
3611 		info->adapter_num = adapter_num;
3612 		info->port_num = port_num;
3613 
3614 		setup_timer(&info->tx_timer, tx_timeout, (unsigned long)info);
3615 		setup_timer(&info->rx_timer, rx_timeout, (unsigned long)info);
3616 
3617 		/* Copy configuration info to device instance data */
3618 		info->pdev = pdev;
3619 		info->irq_level = pdev->irq;
3620 		info->phys_reg_addr = pci_resource_start(pdev,0);
3621 
3622 		info->bus_type = MGSL_BUS_TYPE_PCI;
3623 		info->irq_flags = IRQF_SHARED;
3624 
3625 		info->init_error = -1; /* assume error, set to 0 on successful init */
3626 	}
3627 
3628 	return info;
3629 }
3630 
3631 static void device_init(int adapter_num, struct pci_dev *pdev)
3632 {
3633 	struct slgt_info *port_array[SLGT_MAX_PORTS];
3634 	int i;
3635 	int port_count = 1;
3636 
3637 	if (pdev->device == SYNCLINK_GT2_DEVICE_ID)
3638 		port_count = 2;
3639 	else if (pdev->device == SYNCLINK_GT4_DEVICE_ID)
3640 		port_count = 4;
3641 
3642 	/* allocate device instances for all ports */
3643 	for (i=0; i < port_count; ++i) {
3644 		port_array[i] = alloc_dev(adapter_num, i, pdev);
3645 		if (port_array[i] == NULL) {
3646 			for (--i; i >= 0; --i) {
3647 				tty_port_destroy(&port_array[i]->port);
3648 				kfree(port_array[i]);
3649 			}
3650 			return;
3651 		}
3652 	}
3653 
3654 	/* give copy of port_array to all ports and add to device list  */
3655 	for (i=0; i < port_count; ++i) {
3656 		memcpy(port_array[i]->port_array, port_array, sizeof(port_array));
3657 		add_device(port_array[i]);
3658 		port_array[i]->port_count = port_count;
3659 		spin_lock_init(&port_array[i]->lock);
3660 	}
3661 
3662 	/* Allocate and claim adapter resources */
3663 	if (!claim_resources(port_array[0])) {
3664 
3665 		alloc_dma_bufs(port_array[0]);
3666 
3667 		/* copy resource information from first port to others */
3668 		for (i = 1; i < port_count; ++i) {
3669 			port_array[i]->irq_level = port_array[0]->irq_level;
3670 			port_array[i]->reg_addr  = port_array[0]->reg_addr;
3671 			alloc_dma_bufs(port_array[i]);
3672 		}
3673 
3674 		if (request_irq(port_array[0]->irq_level,
3675 					slgt_interrupt,
3676 					port_array[0]->irq_flags,
3677 					port_array[0]->device_name,
3678 					port_array[0]) < 0) {
3679 			DBGERR(("%s request_irq failed IRQ=%d\n",
3680 				port_array[0]->device_name,
3681 				port_array[0]->irq_level));
3682 		} else {
3683 			port_array[0]->irq_requested = true;
3684 			adapter_test(port_array[0]);
3685 			for (i=1 ; i < port_count ; i++) {
3686 				port_array[i]->init_error = port_array[0]->init_error;
3687 				port_array[i]->gpio_present = port_array[0]->gpio_present;
3688 			}
3689 		}
3690 	}
3691 
3692 	for (i = 0; i < port_count; ++i) {
3693 		struct slgt_info *info = port_array[i];
3694 		tty_port_register_device(&info->port, serial_driver, info->line,
3695 				&info->pdev->dev);
3696 	}
3697 }
3698 
3699 static int init_one(struct pci_dev *dev,
3700 			      const struct pci_device_id *ent)
3701 {
3702 	if (pci_enable_device(dev)) {
3703 		printk("error enabling pci device %p\n", dev);
3704 		return -EIO;
3705 	}
3706 	pci_set_master(dev);
3707 	device_init(slgt_device_count, dev);
3708 	return 0;
3709 }
3710 
3711 static void remove_one(struct pci_dev *dev)
3712 {
3713 }
3714 
3715 static const struct tty_operations ops = {
3716 	.open = open,
3717 	.close = close,
3718 	.write = write,
3719 	.put_char = put_char,
3720 	.flush_chars = flush_chars,
3721 	.write_room = write_room,
3722 	.chars_in_buffer = chars_in_buffer,
3723 	.flush_buffer = flush_buffer,
3724 	.ioctl = ioctl,
3725 	.compat_ioctl = slgt_compat_ioctl,
3726 	.throttle = throttle,
3727 	.unthrottle = unthrottle,
3728 	.send_xchar = send_xchar,
3729 	.break_ctl = set_break,
3730 	.wait_until_sent = wait_until_sent,
3731 	.set_termios = set_termios,
3732 	.stop = tx_hold,
3733 	.start = tx_release,
3734 	.hangup = hangup,
3735 	.tiocmget = tiocmget,
3736 	.tiocmset = tiocmset,
3737 	.get_icount = get_icount,
3738 	.proc_fops = &synclink_gt_proc_fops,
3739 };
3740 
3741 static void slgt_cleanup(void)
3742 {
3743 	int rc;
3744 	struct slgt_info *info;
3745 	struct slgt_info *tmp;
3746 
3747 	printk(KERN_INFO "unload %s\n", driver_name);
3748 
3749 	if (serial_driver) {
3750 		for (info=slgt_device_list ; info != NULL ; info=info->next_device)
3751 			tty_unregister_device(serial_driver, info->line);
3752 		rc = tty_unregister_driver(serial_driver);
3753 		if (rc)
3754 			DBGERR(("tty_unregister_driver error=%d\n", rc));
3755 		put_tty_driver(serial_driver);
3756 	}
3757 
3758 	/* reset devices */
3759 	info = slgt_device_list;
3760 	while(info) {
3761 		reset_port(info);
3762 		info = info->next_device;
3763 	}
3764 
3765 	/* release devices */
3766 	info = slgt_device_list;
3767 	while(info) {
3768 #if SYNCLINK_GENERIC_HDLC
3769 		hdlcdev_exit(info);
3770 #endif
3771 		free_dma_bufs(info);
3772 		free_tmp_rbuf(info);
3773 		if (info->port_num == 0)
3774 			release_resources(info);
3775 		tmp = info;
3776 		info = info->next_device;
3777 		tty_port_destroy(&tmp->port);
3778 		kfree(tmp);
3779 	}
3780 
3781 	if (pci_registered)
3782 		pci_unregister_driver(&pci_driver);
3783 }
3784 
3785 /*
3786  *  Driver initialization entry point.
3787  */
3788 static int __init slgt_init(void)
3789 {
3790 	int rc;
3791 
3792 	printk(KERN_INFO "%s\n", driver_name);
3793 
3794 	serial_driver = alloc_tty_driver(MAX_DEVICES);
3795 	if (!serial_driver) {
3796 		printk("%s can't allocate tty driver\n", driver_name);
3797 		return -ENOMEM;
3798 	}
3799 
3800 	/* Initialize the tty_driver structure */
3801 
3802 	serial_driver->driver_name = slgt_driver_name;
3803 	serial_driver->name = tty_dev_prefix;
3804 	serial_driver->major = ttymajor;
3805 	serial_driver->minor_start = 64;
3806 	serial_driver->type = TTY_DRIVER_TYPE_SERIAL;
3807 	serial_driver->subtype = SERIAL_TYPE_NORMAL;
3808 	serial_driver->init_termios = tty_std_termios;
3809 	serial_driver->init_termios.c_cflag =
3810 		B9600 | CS8 | CREAD | HUPCL | CLOCAL;
3811 	serial_driver->init_termios.c_ispeed = 9600;
3812 	serial_driver->init_termios.c_ospeed = 9600;
3813 	serial_driver->flags = TTY_DRIVER_REAL_RAW | TTY_DRIVER_DYNAMIC_DEV;
3814 	tty_set_operations(serial_driver, &ops);
3815 	if ((rc = tty_register_driver(serial_driver)) < 0) {
3816 		DBGERR(("%s can't register serial driver\n", driver_name));
3817 		put_tty_driver(serial_driver);
3818 		serial_driver = NULL;
3819 		goto error;
3820 	}
3821 
3822 	printk(KERN_INFO "%s, tty major#%d\n",
3823 	       driver_name, serial_driver->major);
3824 
3825 	slgt_device_count = 0;
3826 	if ((rc = pci_register_driver(&pci_driver)) < 0) {
3827 		printk("%s pci_register_driver error=%d\n", driver_name, rc);
3828 		goto error;
3829 	}
3830 	pci_registered = true;
3831 
3832 	if (!slgt_device_list)
3833 		printk("%s no devices found\n",driver_name);
3834 
3835 	return 0;
3836 
3837 error:
3838 	slgt_cleanup();
3839 	return rc;
3840 }
3841 
3842 static void __exit slgt_exit(void)
3843 {
3844 	slgt_cleanup();
3845 }
3846 
3847 module_init(slgt_init);
3848 module_exit(slgt_exit);
3849 
3850 /*
3851  * register access routines
3852  */
3853 
3854 #define CALC_REGADDR() \
3855 	unsigned long reg_addr = ((unsigned long)info->reg_addr) + addr; \
3856 	if (addr >= 0x80) \
3857 		reg_addr += (info->port_num) * 32; \
3858 	else if (addr >= 0x40)	\
3859 		reg_addr += (info->port_num) * 16;
3860 
3861 static __u8 rd_reg8(struct slgt_info *info, unsigned int addr)
3862 {
3863 	CALC_REGADDR();
3864 	return readb((void __iomem *)reg_addr);
3865 }
3866 
3867 static void wr_reg8(struct slgt_info *info, unsigned int addr, __u8 value)
3868 {
3869 	CALC_REGADDR();
3870 	writeb(value, (void __iomem *)reg_addr);
3871 }
3872 
3873 static __u16 rd_reg16(struct slgt_info *info, unsigned int addr)
3874 {
3875 	CALC_REGADDR();
3876 	return readw((void __iomem *)reg_addr);
3877 }
3878 
3879 static void wr_reg16(struct slgt_info *info, unsigned int addr, __u16 value)
3880 {
3881 	CALC_REGADDR();
3882 	writew(value, (void __iomem *)reg_addr);
3883 }
3884 
3885 static __u32 rd_reg32(struct slgt_info *info, unsigned int addr)
3886 {
3887 	CALC_REGADDR();
3888 	return readl((void __iomem *)reg_addr);
3889 }
3890 
3891 static void wr_reg32(struct slgt_info *info, unsigned int addr, __u32 value)
3892 {
3893 	CALC_REGADDR();
3894 	writel(value, (void __iomem *)reg_addr);
3895 }
3896 
3897 static void rdma_reset(struct slgt_info *info)
3898 {
3899 	unsigned int i;
3900 
3901 	/* set reset bit */
3902 	wr_reg32(info, RDCSR, BIT1);
3903 
3904 	/* wait for enable bit cleared */
3905 	for(i=0 ; i < 1000 ; i++)
3906 		if (!(rd_reg32(info, RDCSR) & BIT0))
3907 			break;
3908 }
3909 
3910 static void tdma_reset(struct slgt_info *info)
3911 {
3912 	unsigned int i;
3913 
3914 	/* set reset bit */
3915 	wr_reg32(info, TDCSR, BIT1);
3916 
3917 	/* wait for enable bit cleared */
3918 	for(i=0 ; i < 1000 ; i++)
3919 		if (!(rd_reg32(info, TDCSR) & BIT0))
3920 			break;
3921 }
3922 
3923 /*
3924  * enable internal loopback
3925  * TxCLK and RxCLK are generated from BRG
3926  * and TxD is looped back to RxD internally.
3927  */
3928 static void enable_loopback(struct slgt_info *info)
3929 {
3930 	/* SCR (serial control) BIT2=loopback enable */
3931 	wr_reg16(info, SCR, (unsigned short)(rd_reg16(info, SCR) | BIT2));
3932 
3933 	if (info->params.mode != MGSL_MODE_ASYNC) {
3934 		/* CCR (clock control)
3935 		 * 07..05  tx clock source (010 = BRG)
3936 		 * 04..02  rx clock source (010 = BRG)
3937 		 * 01      auxclk enable   (0 = disable)
3938 		 * 00      BRG enable      (1 = enable)
3939 		 *
3940 		 * 0100 1001
3941 		 */
3942 		wr_reg8(info, CCR, 0x49);
3943 
3944 		/* set speed if available, otherwise use default */
3945 		if (info->params.clock_speed)
3946 			set_rate(info, info->params.clock_speed);
3947 		else
3948 			set_rate(info, 3686400);
3949 	}
3950 }
3951 
3952 /*
3953  *  set baud rate generator to specified rate
3954  */
3955 static void set_rate(struct slgt_info *info, u32 rate)
3956 {
3957 	unsigned int div;
3958 	unsigned int osc = info->base_clock;
3959 
3960 	/* div = osc/rate - 1
3961 	 *
3962 	 * Round div up if osc/rate is not integer to
3963 	 * force to next slowest rate.
3964 	 */
3965 
3966 	if (rate) {
3967 		div = osc/rate;
3968 		if (!(osc % rate) && div)
3969 			div--;
3970 		wr_reg16(info, BDR, (unsigned short)div);
3971 	}
3972 }
3973 
3974 static void rx_stop(struct slgt_info *info)
3975 {
3976 	unsigned short val;
3977 
3978 	/* disable and reset receiver */
3979 	val = rd_reg16(info, RCR) & ~BIT1;          /* clear enable bit */
3980 	wr_reg16(info, RCR, (unsigned short)(val | BIT2)); /* set reset bit */
3981 	wr_reg16(info, RCR, val);                  /* clear reset bit */
3982 
3983 	slgt_irq_off(info, IRQ_RXOVER + IRQ_RXDATA + IRQ_RXIDLE);
3984 
3985 	/* clear pending rx interrupts */
3986 	wr_reg16(info, SSR, IRQ_RXIDLE + IRQ_RXOVER);
3987 
3988 	rdma_reset(info);
3989 
3990 	info->rx_enabled = false;
3991 	info->rx_restart = false;
3992 }
3993 
3994 static void rx_start(struct slgt_info *info)
3995 {
3996 	unsigned short val;
3997 
3998 	slgt_irq_off(info, IRQ_RXOVER + IRQ_RXDATA);
3999 
4000 	/* clear pending rx overrun IRQ */
4001 	wr_reg16(info, SSR, IRQ_RXOVER);
4002 
4003 	/* reset and disable receiver */
4004 	val = rd_reg16(info, RCR) & ~BIT1; /* clear enable bit */
4005 	wr_reg16(info, RCR, (unsigned short)(val | BIT2)); /* set reset bit */
4006 	wr_reg16(info, RCR, val);                  /* clear reset bit */
4007 
4008 	rdma_reset(info);
4009 	reset_rbufs(info);
4010 
4011 	if (info->rx_pio) {
4012 		/* rx request when rx FIFO not empty */
4013 		wr_reg16(info, SCR, (unsigned short)(rd_reg16(info, SCR) & ~BIT14));
4014 		slgt_irq_on(info, IRQ_RXDATA);
4015 		if (info->params.mode == MGSL_MODE_ASYNC) {
4016 			/* enable saving of rx status */
4017 			wr_reg32(info, RDCSR, BIT6);
4018 		}
4019 	} else {
4020 		/* rx request when rx FIFO half full */
4021 		wr_reg16(info, SCR, (unsigned short)(rd_reg16(info, SCR) | BIT14));
4022 		/* set 1st descriptor address */
4023 		wr_reg32(info, RDDAR, info->rbufs[0].pdesc);
4024 
4025 		if (info->params.mode != MGSL_MODE_ASYNC) {
4026 			/* enable rx DMA and DMA interrupt */
4027 			wr_reg32(info, RDCSR, (BIT2 + BIT0));
4028 		} else {
4029 			/* enable saving of rx status, rx DMA and DMA interrupt */
4030 			wr_reg32(info, RDCSR, (BIT6 + BIT2 + BIT0));
4031 		}
4032 	}
4033 
4034 	slgt_irq_on(info, IRQ_RXOVER);
4035 
4036 	/* enable receiver */
4037 	wr_reg16(info, RCR, (unsigned short)(rd_reg16(info, RCR) | BIT1));
4038 
4039 	info->rx_restart = false;
4040 	info->rx_enabled = true;
4041 }
4042 
4043 static void tx_start(struct slgt_info *info)
4044 {
4045 	if (!info->tx_enabled) {
4046 		wr_reg16(info, TCR,
4047 			 (unsigned short)((rd_reg16(info, TCR) | BIT1) & ~BIT2));
4048 		info->tx_enabled = true;
4049 	}
4050 
4051 	if (desc_count(info->tbufs[info->tbuf_start])) {
4052 		info->drop_rts_on_tx_done = false;
4053 
4054 		if (info->params.mode != MGSL_MODE_ASYNC) {
4055 			if (info->params.flags & HDLC_FLAG_AUTO_RTS) {
4056 				get_signals(info);
4057 				if (!(info->signals & SerialSignal_RTS)) {
4058 					info->signals |= SerialSignal_RTS;
4059 					set_signals(info);
4060 					info->drop_rts_on_tx_done = true;
4061 				}
4062 			}
4063 
4064 			slgt_irq_off(info, IRQ_TXDATA);
4065 			slgt_irq_on(info, IRQ_TXUNDER + IRQ_TXIDLE);
4066 			/* clear tx idle and underrun status bits */
4067 			wr_reg16(info, SSR, (unsigned short)(IRQ_TXIDLE + IRQ_TXUNDER));
4068 		} else {
4069 			slgt_irq_off(info, IRQ_TXDATA);
4070 			slgt_irq_on(info, IRQ_TXIDLE);
4071 			/* clear tx idle status bit */
4072 			wr_reg16(info, SSR, IRQ_TXIDLE);
4073 		}
4074 		/* set 1st descriptor address and start DMA */
4075 		wr_reg32(info, TDDAR, info->tbufs[info->tbuf_start].pdesc);
4076 		wr_reg32(info, TDCSR, BIT2 + BIT0);
4077 		info->tx_active = true;
4078 	}
4079 }
4080 
4081 static void tx_stop(struct slgt_info *info)
4082 {
4083 	unsigned short val;
4084 
4085 	del_timer(&info->tx_timer);
4086 
4087 	tdma_reset(info);
4088 
4089 	/* reset and disable transmitter */
4090 	val = rd_reg16(info, TCR) & ~BIT1;          /* clear enable bit */
4091 	wr_reg16(info, TCR, (unsigned short)(val | BIT2)); /* set reset bit */
4092 
4093 	slgt_irq_off(info, IRQ_TXDATA + IRQ_TXIDLE + IRQ_TXUNDER);
4094 
4095 	/* clear tx idle and underrun status bit */
4096 	wr_reg16(info, SSR, (unsigned short)(IRQ_TXIDLE + IRQ_TXUNDER));
4097 
4098 	reset_tbufs(info);
4099 
4100 	info->tx_enabled = false;
4101 	info->tx_active = false;
4102 }
4103 
4104 static void reset_port(struct slgt_info *info)
4105 {
4106 	if (!info->reg_addr)
4107 		return;
4108 
4109 	tx_stop(info);
4110 	rx_stop(info);
4111 
4112 	info->signals &= ~(SerialSignal_RTS | SerialSignal_DTR);
4113 	set_signals(info);
4114 
4115 	slgt_irq_off(info, IRQ_ALL | IRQ_MASTER);
4116 }
4117 
4118 static void reset_adapter(struct slgt_info *info)
4119 {
4120 	int i;
4121 	for (i=0; i < info->port_count; ++i) {
4122 		if (info->port_array[i])
4123 			reset_port(info->port_array[i]);
4124 	}
4125 }
4126 
4127 static void async_mode(struct slgt_info *info)
4128 {
4129   	unsigned short val;
4130 
4131 	slgt_irq_off(info, IRQ_ALL | IRQ_MASTER);
4132 	tx_stop(info);
4133 	rx_stop(info);
4134 
4135 	/* TCR (tx control)
4136 	 *
4137 	 * 15..13  mode, 010=async
4138 	 * 12..10  encoding, 000=NRZ
4139 	 * 09      parity enable
4140 	 * 08      1=odd parity, 0=even parity
4141 	 * 07      1=RTS driver control
4142 	 * 06      1=break enable
4143 	 * 05..04  character length
4144 	 *         00=5 bits
4145 	 *         01=6 bits
4146 	 *         10=7 bits
4147 	 *         11=8 bits
4148 	 * 03      0=1 stop bit, 1=2 stop bits
4149 	 * 02      reset
4150 	 * 01      enable
4151 	 * 00      auto-CTS enable
4152 	 */
4153 	val = 0x4000;
4154 
4155 	if (info->if_mode & MGSL_INTERFACE_RTS_EN)
4156 		val |= BIT7;
4157 
4158 	if (info->params.parity != ASYNC_PARITY_NONE) {
4159 		val |= BIT9;
4160 		if (info->params.parity == ASYNC_PARITY_ODD)
4161 			val |= BIT8;
4162 	}
4163 
4164 	switch (info->params.data_bits)
4165 	{
4166 	case 6: val |= BIT4; break;
4167 	case 7: val |= BIT5; break;
4168 	case 8: val |= BIT5 + BIT4; break;
4169 	}
4170 
4171 	if (info->params.stop_bits != 1)
4172 		val |= BIT3;
4173 
4174 	if (info->params.flags & HDLC_FLAG_AUTO_CTS)
4175 		val |= BIT0;
4176 
4177 	wr_reg16(info, TCR, val);
4178 
4179 	/* RCR (rx control)
4180 	 *
4181 	 * 15..13  mode, 010=async
4182 	 * 12..10  encoding, 000=NRZ
4183 	 * 09      parity enable
4184 	 * 08      1=odd parity, 0=even parity
4185 	 * 07..06  reserved, must be 0
4186 	 * 05..04  character length
4187 	 *         00=5 bits
4188 	 *         01=6 bits
4189 	 *         10=7 bits
4190 	 *         11=8 bits
4191 	 * 03      reserved, must be zero
4192 	 * 02      reset
4193 	 * 01      enable
4194 	 * 00      auto-DCD enable
4195 	 */
4196 	val = 0x4000;
4197 
4198 	if (info->params.parity != ASYNC_PARITY_NONE) {
4199 		val |= BIT9;
4200 		if (info->params.parity == ASYNC_PARITY_ODD)
4201 			val |= BIT8;
4202 	}
4203 
4204 	switch (info->params.data_bits)
4205 	{
4206 	case 6: val |= BIT4; break;
4207 	case 7: val |= BIT5; break;
4208 	case 8: val |= BIT5 + BIT4; break;
4209 	}
4210 
4211 	if (info->params.flags & HDLC_FLAG_AUTO_DCD)
4212 		val |= BIT0;
4213 
4214 	wr_reg16(info, RCR, val);
4215 
4216 	/* CCR (clock control)
4217 	 *
4218 	 * 07..05  011 = tx clock source is BRG/16
4219 	 * 04..02  010 = rx clock source is BRG
4220 	 * 01      0 = auxclk disabled
4221 	 * 00      1 = BRG enabled
4222 	 *
4223 	 * 0110 1001
4224 	 */
4225 	wr_reg8(info, CCR, 0x69);
4226 
4227 	msc_set_vcr(info);
4228 
4229 	/* SCR (serial control)
4230 	 *
4231 	 * 15  1=tx req on FIFO half empty
4232 	 * 14  1=rx req on FIFO half full
4233 	 * 13  tx data  IRQ enable
4234 	 * 12  tx idle  IRQ enable
4235 	 * 11  rx break on IRQ enable
4236 	 * 10  rx data  IRQ enable
4237 	 * 09  rx break off IRQ enable
4238 	 * 08  overrun  IRQ enable
4239 	 * 07  DSR      IRQ enable
4240 	 * 06  CTS      IRQ enable
4241 	 * 05  DCD      IRQ enable
4242 	 * 04  RI       IRQ enable
4243 	 * 03  0=16x sampling, 1=8x sampling
4244 	 * 02  1=txd->rxd internal loopback enable
4245 	 * 01  reserved, must be zero
4246 	 * 00  1=master IRQ enable
4247 	 */
4248 	val = BIT15 + BIT14 + BIT0;
4249 	/* JCR[8] : 1 = x8 async mode feature available */
4250 	if ((rd_reg32(info, JCR) & BIT8) && info->params.data_rate &&
4251 	    ((info->base_clock < (info->params.data_rate * 16)) ||
4252 	     (info->base_clock % (info->params.data_rate * 16)))) {
4253 		/* use 8x sampling */
4254 		val |= BIT3;
4255 		set_rate(info, info->params.data_rate * 8);
4256 	} else {
4257 		/* use 16x sampling */
4258 		set_rate(info, info->params.data_rate * 16);
4259 	}
4260 	wr_reg16(info, SCR, val);
4261 
4262 	slgt_irq_on(info, IRQ_RXBREAK | IRQ_RXOVER);
4263 
4264 	if (info->params.loopback)
4265 		enable_loopback(info);
4266 }
4267 
4268 static void sync_mode(struct slgt_info *info)
4269 {
4270 	unsigned short val;
4271 
4272 	slgt_irq_off(info, IRQ_ALL | IRQ_MASTER);
4273 	tx_stop(info);
4274 	rx_stop(info);
4275 
4276 	/* TCR (tx control)
4277 	 *
4278 	 * 15..13  mode
4279 	 *         000=HDLC/SDLC
4280 	 *         001=raw bit synchronous
4281 	 *         010=asynchronous/isochronous
4282 	 *         011=monosync byte synchronous
4283 	 *         100=bisync byte synchronous
4284 	 *         101=xsync byte synchronous
4285 	 * 12..10  encoding
4286 	 * 09      CRC enable
4287 	 * 08      CRC32
4288 	 * 07      1=RTS driver control
4289 	 * 06      preamble enable
4290 	 * 05..04  preamble length
4291 	 * 03      share open/close flag
4292 	 * 02      reset
4293 	 * 01      enable
4294 	 * 00      auto-CTS enable
4295 	 */
4296 	val = BIT2;
4297 
4298 	switch(info->params.mode) {
4299 	case MGSL_MODE_XSYNC:
4300 		val |= BIT15 + BIT13;
4301 		break;
4302 	case MGSL_MODE_MONOSYNC: val |= BIT14 + BIT13; break;
4303 	case MGSL_MODE_BISYNC:   val |= BIT15; break;
4304 	case MGSL_MODE_RAW:      val |= BIT13; break;
4305 	}
4306 	if (info->if_mode & MGSL_INTERFACE_RTS_EN)
4307 		val |= BIT7;
4308 
4309 	switch(info->params.encoding)
4310 	{
4311 	case HDLC_ENCODING_NRZB:          val |= BIT10; break;
4312 	case HDLC_ENCODING_NRZI_MARK:     val |= BIT11; break;
4313 	case HDLC_ENCODING_NRZI:          val |= BIT11 + BIT10; break;
4314 	case HDLC_ENCODING_BIPHASE_MARK:  val |= BIT12; break;
4315 	case HDLC_ENCODING_BIPHASE_SPACE: val |= BIT12 + BIT10; break;
4316 	case HDLC_ENCODING_BIPHASE_LEVEL: val |= BIT12 + BIT11; break;
4317 	case HDLC_ENCODING_DIFF_BIPHASE_LEVEL: val |= BIT12 + BIT11 + BIT10; break;
4318 	}
4319 
4320 	switch (info->params.crc_type & HDLC_CRC_MASK)
4321 	{
4322 	case HDLC_CRC_16_CCITT: val |= BIT9; break;
4323 	case HDLC_CRC_32_CCITT: val |= BIT9 + BIT8; break;
4324 	}
4325 
4326 	if (info->params.preamble != HDLC_PREAMBLE_PATTERN_NONE)
4327 		val |= BIT6;
4328 
4329 	switch (info->params.preamble_length)
4330 	{
4331 	case HDLC_PREAMBLE_LENGTH_16BITS: val |= BIT5; break;
4332 	case HDLC_PREAMBLE_LENGTH_32BITS: val |= BIT4; break;
4333 	case HDLC_PREAMBLE_LENGTH_64BITS: val |= BIT5 + BIT4; break;
4334 	}
4335 
4336 	if (info->params.flags & HDLC_FLAG_AUTO_CTS)
4337 		val |= BIT0;
4338 
4339 	wr_reg16(info, TCR, val);
4340 
4341 	/* TPR (transmit preamble) */
4342 
4343 	switch (info->params.preamble)
4344 	{
4345 	case HDLC_PREAMBLE_PATTERN_FLAGS: val = 0x7e; break;
4346 	case HDLC_PREAMBLE_PATTERN_ONES:  val = 0xff; break;
4347 	case HDLC_PREAMBLE_PATTERN_ZEROS: val = 0x00; break;
4348 	case HDLC_PREAMBLE_PATTERN_10:    val = 0x55; break;
4349 	case HDLC_PREAMBLE_PATTERN_01:    val = 0xaa; break;
4350 	default:                          val = 0x7e; break;
4351 	}
4352 	wr_reg8(info, TPR, (unsigned char)val);
4353 
4354 	/* RCR (rx control)
4355 	 *
4356 	 * 15..13  mode
4357 	 *         000=HDLC/SDLC
4358 	 *         001=raw bit synchronous
4359 	 *         010=asynchronous/isochronous
4360 	 *         011=monosync byte synchronous
4361 	 *         100=bisync byte synchronous
4362 	 *         101=xsync byte synchronous
4363 	 * 12..10  encoding
4364 	 * 09      CRC enable
4365 	 * 08      CRC32
4366 	 * 07..03  reserved, must be 0
4367 	 * 02      reset
4368 	 * 01      enable
4369 	 * 00      auto-DCD enable
4370 	 */
4371 	val = 0;
4372 
4373 	switch(info->params.mode) {
4374 	case MGSL_MODE_XSYNC:
4375 		val |= BIT15 + BIT13;
4376 		break;
4377 	case MGSL_MODE_MONOSYNC: val |= BIT14 + BIT13; break;
4378 	case MGSL_MODE_BISYNC:   val |= BIT15; break;
4379 	case MGSL_MODE_RAW:      val |= BIT13; break;
4380 	}
4381 
4382 	switch(info->params.encoding)
4383 	{
4384 	case HDLC_ENCODING_NRZB:          val |= BIT10; break;
4385 	case HDLC_ENCODING_NRZI_MARK:     val |= BIT11; break;
4386 	case HDLC_ENCODING_NRZI:          val |= BIT11 + BIT10; break;
4387 	case HDLC_ENCODING_BIPHASE_MARK:  val |= BIT12; break;
4388 	case HDLC_ENCODING_BIPHASE_SPACE: val |= BIT12 + BIT10; break;
4389 	case HDLC_ENCODING_BIPHASE_LEVEL: val |= BIT12 + BIT11; break;
4390 	case HDLC_ENCODING_DIFF_BIPHASE_LEVEL: val |= BIT12 + BIT11 + BIT10; break;
4391 	}
4392 
4393 	switch (info->params.crc_type & HDLC_CRC_MASK)
4394 	{
4395 	case HDLC_CRC_16_CCITT: val |= BIT9; break;
4396 	case HDLC_CRC_32_CCITT: val |= BIT9 + BIT8; break;
4397 	}
4398 
4399 	if (info->params.flags & HDLC_FLAG_AUTO_DCD)
4400 		val |= BIT0;
4401 
4402 	wr_reg16(info, RCR, val);
4403 
4404 	/* CCR (clock control)
4405 	 *
4406 	 * 07..05  tx clock source
4407 	 * 04..02  rx clock source
4408 	 * 01      auxclk enable
4409 	 * 00      BRG enable
4410 	 */
4411 	val = 0;
4412 
4413 	if (info->params.flags & HDLC_FLAG_TXC_BRG)
4414 	{
4415 		// when RxC source is DPLL, BRG generates 16X DPLL
4416 		// reference clock, so take TxC from BRG/16 to get
4417 		// transmit clock at actual data rate
4418 		if (info->params.flags & HDLC_FLAG_RXC_DPLL)
4419 			val |= BIT6 + BIT5;	/* 011, txclk = BRG/16 */
4420 		else
4421 			val |= BIT6;	/* 010, txclk = BRG */
4422 	}
4423 	else if (info->params.flags & HDLC_FLAG_TXC_DPLL)
4424 		val |= BIT7;	/* 100, txclk = DPLL Input */
4425 	else if (info->params.flags & HDLC_FLAG_TXC_RXCPIN)
4426 		val |= BIT5;	/* 001, txclk = RXC Input */
4427 
4428 	if (info->params.flags & HDLC_FLAG_RXC_BRG)
4429 		val |= BIT3;	/* 010, rxclk = BRG */
4430 	else if (info->params.flags & HDLC_FLAG_RXC_DPLL)
4431 		val |= BIT4;	/* 100, rxclk = DPLL */
4432 	else if (info->params.flags & HDLC_FLAG_RXC_TXCPIN)
4433 		val |= BIT2;	/* 001, rxclk = TXC Input */
4434 
4435 	if (info->params.clock_speed)
4436 		val |= BIT1 + BIT0;
4437 
4438 	wr_reg8(info, CCR, (unsigned char)val);
4439 
4440 	if (info->params.flags & (HDLC_FLAG_TXC_DPLL + HDLC_FLAG_RXC_DPLL))
4441 	{
4442 		// program DPLL mode
4443 		switch(info->params.encoding)
4444 		{
4445 		case HDLC_ENCODING_BIPHASE_MARK:
4446 		case HDLC_ENCODING_BIPHASE_SPACE:
4447 			val = BIT7; break;
4448 		case HDLC_ENCODING_BIPHASE_LEVEL:
4449 		case HDLC_ENCODING_DIFF_BIPHASE_LEVEL:
4450 			val = BIT7 + BIT6; break;
4451 		default: val = BIT6;	// NRZ encodings
4452 		}
4453 		wr_reg16(info, RCR, (unsigned short)(rd_reg16(info, RCR) | val));
4454 
4455 		// DPLL requires a 16X reference clock from BRG
4456 		set_rate(info, info->params.clock_speed * 16);
4457 	}
4458 	else
4459 		set_rate(info, info->params.clock_speed);
4460 
4461 	tx_set_idle(info);
4462 
4463 	msc_set_vcr(info);
4464 
4465 	/* SCR (serial control)
4466 	 *
4467 	 * 15  1=tx req on FIFO half empty
4468 	 * 14  1=rx req on FIFO half full
4469 	 * 13  tx data  IRQ enable
4470 	 * 12  tx idle  IRQ enable
4471 	 * 11  underrun IRQ enable
4472 	 * 10  rx data  IRQ enable
4473 	 * 09  rx idle  IRQ enable
4474 	 * 08  overrun  IRQ enable
4475 	 * 07  DSR      IRQ enable
4476 	 * 06  CTS      IRQ enable
4477 	 * 05  DCD      IRQ enable
4478 	 * 04  RI       IRQ enable
4479 	 * 03  reserved, must be zero
4480 	 * 02  1=txd->rxd internal loopback enable
4481 	 * 01  reserved, must be zero
4482 	 * 00  1=master IRQ enable
4483 	 */
4484 	wr_reg16(info, SCR, BIT15 + BIT14 + BIT0);
4485 
4486 	if (info->params.loopback)
4487 		enable_loopback(info);
4488 }
4489 
4490 /*
4491  *  set transmit idle mode
4492  */
4493 static void tx_set_idle(struct slgt_info *info)
4494 {
4495 	unsigned char val;
4496 	unsigned short tcr;
4497 
4498 	/* if preamble enabled (tcr[6] == 1) then tx idle size = 8 bits
4499 	 * else tcr[5:4] = tx idle size: 00 = 8 bits, 01 = 16 bits
4500 	 */
4501 	tcr = rd_reg16(info, TCR);
4502 	if (info->idle_mode & HDLC_TXIDLE_CUSTOM_16) {
4503 		/* disable preamble, set idle size to 16 bits */
4504 		tcr = (tcr & ~(BIT6 + BIT5)) | BIT4;
4505 		/* MSB of 16 bit idle specified in tx preamble register (TPR) */
4506 		wr_reg8(info, TPR, (unsigned char)((info->idle_mode >> 8) & 0xff));
4507 	} else if (!(tcr & BIT6)) {
4508 		/* preamble is disabled, set idle size to 8 bits */
4509 		tcr &= ~(BIT5 + BIT4);
4510 	}
4511 	wr_reg16(info, TCR, tcr);
4512 
4513 	if (info->idle_mode & (HDLC_TXIDLE_CUSTOM_8 | HDLC_TXIDLE_CUSTOM_16)) {
4514 		/* LSB of custom tx idle specified in tx idle register */
4515 		val = (unsigned char)(info->idle_mode & 0xff);
4516 	} else {
4517 		/* standard 8 bit idle patterns */
4518 		switch(info->idle_mode)
4519 		{
4520 		case HDLC_TXIDLE_FLAGS:          val = 0x7e; break;
4521 		case HDLC_TXIDLE_ALT_ZEROS_ONES:
4522 		case HDLC_TXIDLE_ALT_MARK_SPACE: val = 0xaa; break;
4523 		case HDLC_TXIDLE_ZEROS:
4524 		case HDLC_TXIDLE_SPACE:          val = 0x00; break;
4525 		default:                         val = 0xff;
4526 		}
4527 	}
4528 
4529 	wr_reg8(info, TIR, val);
4530 }
4531 
4532 /*
4533  * get state of V24 status (input) signals
4534  */
4535 static void get_signals(struct slgt_info *info)
4536 {
4537 	unsigned short status = rd_reg16(info, SSR);
4538 
4539 	/* clear all serial signals except RTS and DTR */
4540 	info->signals &= SerialSignal_RTS | SerialSignal_DTR;
4541 
4542 	if (status & BIT3)
4543 		info->signals |= SerialSignal_DSR;
4544 	if (status & BIT2)
4545 		info->signals |= SerialSignal_CTS;
4546 	if (status & BIT1)
4547 		info->signals |= SerialSignal_DCD;
4548 	if (status & BIT0)
4549 		info->signals |= SerialSignal_RI;
4550 }
4551 
4552 /*
4553  * set V.24 Control Register based on current configuration
4554  */
4555 static void msc_set_vcr(struct slgt_info *info)
4556 {
4557 	unsigned char val = 0;
4558 
4559 	/* VCR (V.24 control)
4560 	 *
4561 	 * 07..04  serial IF select
4562 	 * 03      DTR
4563 	 * 02      RTS
4564 	 * 01      LL
4565 	 * 00      RL
4566 	 */
4567 
4568 	switch(info->if_mode & MGSL_INTERFACE_MASK)
4569 	{
4570 	case MGSL_INTERFACE_RS232:
4571 		val |= BIT5; /* 0010 */
4572 		break;
4573 	case MGSL_INTERFACE_V35:
4574 		val |= BIT7 + BIT6 + BIT5; /* 1110 */
4575 		break;
4576 	case MGSL_INTERFACE_RS422:
4577 		val |= BIT6; /* 0100 */
4578 		break;
4579 	}
4580 
4581 	if (info->if_mode & MGSL_INTERFACE_MSB_FIRST)
4582 		val |= BIT4;
4583 	if (info->signals & SerialSignal_DTR)
4584 		val |= BIT3;
4585 	if (info->signals & SerialSignal_RTS)
4586 		val |= BIT2;
4587 	if (info->if_mode & MGSL_INTERFACE_LL)
4588 		val |= BIT1;
4589 	if (info->if_mode & MGSL_INTERFACE_RL)
4590 		val |= BIT0;
4591 	wr_reg8(info, VCR, val);
4592 }
4593 
4594 /*
4595  * set state of V24 control (output) signals
4596  */
4597 static void set_signals(struct slgt_info *info)
4598 {
4599 	unsigned char val = rd_reg8(info, VCR);
4600 	if (info->signals & SerialSignal_DTR)
4601 		val |= BIT3;
4602 	else
4603 		val &= ~BIT3;
4604 	if (info->signals & SerialSignal_RTS)
4605 		val |= BIT2;
4606 	else
4607 		val &= ~BIT2;
4608 	wr_reg8(info, VCR, val);
4609 }
4610 
4611 /*
4612  * free range of receive DMA buffers (i to last)
4613  */
4614 static void free_rbufs(struct slgt_info *info, unsigned int i, unsigned int last)
4615 {
4616 	int done = 0;
4617 
4618 	while(!done) {
4619 		/* reset current buffer for reuse */
4620 		info->rbufs[i].status = 0;
4621 		set_desc_count(info->rbufs[i], info->rbuf_fill_level);
4622 		if (i == last)
4623 			done = 1;
4624 		if (++i == info->rbuf_count)
4625 			i = 0;
4626 	}
4627 	info->rbuf_current = i;
4628 }
4629 
4630 /*
4631  * mark all receive DMA buffers as free
4632  */
4633 static void reset_rbufs(struct slgt_info *info)
4634 {
4635 	free_rbufs(info, 0, info->rbuf_count - 1);
4636 	info->rbuf_fill_index = 0;
4637 	info->rbuf_fill_count = 0;
4638 }
4639 
4640 /*
4641  * pass receive HDLC frame to upper layer
4642  *
4643  * return true if frame available, otherwise false
4644  */
4645 static bool rx_get_frame(struct slgt_info *info)
4646 {
4647 	unsigned int start, end;
4648 	unsigned short status;
4649 	unsigned int framesize = 0;
4650 	unsigned long flags;
4651 	struct tty_struct *tty = info->port.tty;
4652 	unsigned char addr_field = 0xff;
4653 	unsigned int crc_size = 0;
4654 
4655 	switch (info->params.crc_type & HDLC_CRC_MASK) {
4656 	case HDLC_CRC_16_CCITT: crc_size = 2; break;
4657 	case HDLC_CRC_32_CCITT: crc_size = 4; break;
4658 	}
4659 
4660 check_again:
4661 
4662 	framesize = 0;
4663 	addr_field = 0xff;
4664 	start = end = info->rbuf_current;
4665 
4666 	for (;;) {
4667 		if (!desc_complete(info->rbufs[end]))
4668 			goto cleanup;
4669 
4670 		if (framesize == 0 && info->params.addr_filter != 0xff)
4671 			addr_field = info->rbufs[end].buf[0];
4672 
4673 		framesize += desc_count(info->rbufs[end]);
4674 
4675 		if (desc_eof(info->rbufs[end]))
4676 			break;
4677 
4678 		if (++end == info->rbuf_count)
4679 			end = 0;
4680 
4681 		if (end == info->rbuf_current) {
4682 			if (info->rx_enabled){
4683 				spin_lock_irqsave(&info->lock,flags);
4684 				rx_start(info);
4685 				spin_unlock_irqrestore(&info->lock,flags);
4686 			}
4687 			goto cleanup;
4688 		}
4689 	}
4690 
4691 	/* status
4692 	 *
4693 	 * 15      buffer complete
4694 	 * 14..06  reserved
4695 	 * 05..04  residue
4696 	 * 02      eof (end of frame)
4697 	 * 01      CRC error
4698 	 * 00      abort
4699 	 */
4700 	status = desc_status(info->rbufs[end]);
4701 
4702 	/* ignore CRC bit if not using CRC (bit is undefined) */
4703 	if ((info->params.crc_type & HDLC_CRC_MASK) == HDLC_CRC_NONE)
4704 		status &= ~BIT1;
4705 
4706 	if (framesize == 0 ||
4707 		 (addr_field != 0xff && addr_field != info->params.addr_filter)) {
4708 		free_rbufs(info, start, end);
4709 		goto check_again;
4710 	}
4711 
4712 	if (framesize < (2 + crc_size) || status & BIT0) {
4713 		info->icount.rxshort++;
4714 		framesize = 0;
4715 	} else if (status & BIT1) {
4716 		info->icount.rxcrc++;
4717 		if (!(info->params.crc_type & HDLC_CRC_RETURN_EX))
4718 			framesize = 0;
4719 	}
4720 
4721 #if SYNCLINK_GENERIC_HDLC
4722 	if (framesize == 0) {
4723 		info->netdev->stats.rx_errors++;
4724 		info->netdev->stats.rx_frame_errors++;
4725 	}
4726 #endif
4727 
4728 	DBGBH(("%s rx frame status=%04X size=%d\n",
4729 		info->device_name, status, framesize));
4730 	DBGDATA(info, info->rbufs[start].buf, min_t(int, framesize, info->rbuf_fill_level), "rx");
4731 
4732 	if (framesize) {
4733 		if (!(info->params.crc_type & HDLC_CRC_RETURN_EX)) {
4734 			framesize -= crc_size;
4735 			crc_size = 0;
4736 		}
4737 
4738 		if (framesize > info->max_frame_size + crc_size)
4739 			info->icount.rxlong++;
4740 		else {
4741 			/* copy dma buffer(s) to contiguous temp buffer */
4742 			int copy_count = framesize;
4743 			int i = start;
4744 			unsigned char *p = info->tmp_rbuf;
4745 			info->tmp_rbuf_count = framesize;
4746 
4747 			info->icount.rxok++;
4748 
4749 			while(copy_count) {
4750 				int partial_count = min_t(int, copy_count, info->rbuf_fill_level);
4751 				memcpy(p, info->rbufs[i].buf, partial_count);
4752 				p += partial_count;
4753 				copy_count -= partial_count;
4754 				if (++i == info->rbuf_count)
4755 					i = 0;
4756 			}
4757 
4758 			if (info->params.crc_type & HDLC_CRC_RETURN_EX) {
4759 				*p = (status & BIT1) ? RX_CRC_ERROR : RX_OK;
4760 				framesize++;
4761 			}
4762 
4763 #if SYNCLINK_GENERIC_HDLC
4764 			if (info->netcount)
4765 				hdlcdev_rx(info,info->tmp_rbuf, framesize);
4766 			else
4767 #endif
4768 				ldisc_receive_buf(tty, info->tmp_rbuf, info->flag_buf, framesize);
4769 		}
4770 	}
4771 	free_rbufs(info, start, end);
4772 	return true;
4773 
4774 cleanup:
4775 	return false;
4776 }
4777 
4778 /*
4779  * pass receive buffer (RAW synchronous mode) to tty layer
4780  * return true if buffer available, otherwise false
4781  */
4782 static bool rx_get_buf(struct slgt_info *info)
4783 {
4784 	unsigned int i = info->rbuf_current;
4785 	unsigned int count;
4786 
4787 	if (!desc_complete(info->rbufs[i]))
4788 		return false;
4789 	count = desc_count(info->rbufs[i]);
4790 	switch(info->params.mode) {
4791 	case MGSL_MODE_MONOSYNC:
4792 	case MGSL_MODE_BISYNC:
4793 	case MGSL_MODE_XSYNC:
4794 		/* ignore residue in byte synchronous modes */
4795 		if (desc_residue(info->rbufs[i]))
4796 			count--;
4797 		break;
4798 	}
4799 	DBGDATA(info, info->rbufs[i].buf, count, "rx");
4800 	DBGINFO(("rx_get_buf size=%d\n", count));
4801 	if (count)
4802 		ldisc_receive_buf(info->port.tty, info->rbufs[i].buf,
4803 				  info->flag_buf, count);
4804 	free_rbufs(info, i, i);
4805 	return true;
4806 }
4807 
4808 static void reset_tbufs(struct slgt_info *info)
4809 {
4810 	unsigned int i;
4811 	info->tbuf_current = 0;
4812 	for (i=0 ; i < info->tbuf_count ; i++) {
4813 		info->tbufs[i].status = 0;
4814 		info->tbufs[i].count  = 0;
4815 	}
4816 }
4817 
4818 /*
4819  * return number of free transmit DMA buffers
4820  */
4821 static unsigned int free_tbuf_count(struct slgt_info *info)
4822 {
4823 	unsigned int count = 0;
4824 	unsigned int i = info->tbuf_current;
4825 
4826 	do
4827 	{
4828 		if (desc_count(info->tbufs[i]))
4829 			break; /* buffer in use */
4830 		++count;
4831 		if (++i == info->tbuf_count)
4832 			i=0;
4833 	} while (i != info->tbuf_current);
4834 
4835 	/* if tx DMA active, last zero count buffer is in use */
4836 	if (count && (rd_reg32(info, TDCSR) & BIT0))
4837 		--count;
4838 
4839 	return count;
4840 }
4841 
4842 /*
4843  * return number of bytes in unsent transmit DMA buffers
4844  * and the serial controller tx FIFO
4845  */
4846 static unsigned int tbuf_bytes(struct slgt_info *info)
4847 {
4848 	unsigned int total_count = 0;
4849 	unsigned int i = info->tbuf_current;
4850 	unsigned int reg_value;
4851 	unsigned int count;
4852 	unsigned int active_buf_count = 0;
4853 
4854 	/*
4855 	 * Add descriptor counts for all tx DMA buffers.
4856 	 * If count is zero (cleared by DMA controller after read),
4857 	 * the buffer is complete or is actively being read from.
4858 	 *
4859 	 * Record buf_count of last buffer with zero count starting
4860 	 * from current ring position. buf_count is mirror
4861 	 * copy of count and is not cleared by serial controller.
4862 	 * If DMA controller is active, that buffer is actively
4863 	 * being read so add to total.
4864 	 */
4865 	do {
4866 		count = desc_count(info->tbufs[i]);
4867 		if (count)
4868 			total_count += count;
4869 		else if (!total_count)
4870 			active_buf_count = info->tbufs[i].buf_count;
4871 		if (++i == info->tbuf_count)
4872 			i = 0;
4873 	} while (i != info->tbuf_current);
4874 
4875 	/* read tx DMA status register */
4876 	reg_value = rd_reg32(info, TDCSR);
4877 
4878 	/* if tx DMA active, last zero count buffer is in use */
4879 	if (reg_value & BIT0)
4880 		total_count += active_buf_count;
4881 
4882 	/* add tx FIFO count = reg_value[15..8] */
4883 	total_count += (reg_value >> 8) & 0xff;
4884 
4885 	/* if transmitter active add one byte for shift register */
4886 	if (info->tx_active)
4887 		total_count++;
4888 
4889 	return total_count;
4890 }
4891 
4892 /*
4893  * load data into transmit DMA buffer ring and start transmitter if needed
4894  * return true if data accepted, otherwise false (buffers full)
4895  */
4896 static bool tx_load(struct slgt_info *info, const char *buf, unsigned int size)
4897 {
4898 	unsigned short count;
4899 	unsigned int i;
4900 	struct slgt_desc *d;
4901 
4902 	/* check required buffer space */
4903 	if (DIV_ROUND_UP(size, DMABUFSIZE) > free_tbuf_count(info))
4904 		return false;
4905 
4906 	DBGDATA(info, buf, size, "tx");
4907 
4908 	/*
4909 	 * copy data to one or more DMA buffers in circular ring
4910 	 * tbuf_start   = first buffer for this data
4911 	 * tbuf_current = next free buffer
4912 	 *
4913 	 * Copy all data before making data visible to DMA controller by
4914 	 * setting descriptor count of the first buffer.
4915 	 * This prevents an active DMA controller from reading the first DMA
4916 	 * buffers of a frame and stopping before the final buffers are filled.
4917 	 */
4918 
4919 	info->tbuf_start = i = info->tbuf_current;
4920 
4921 	while (size) {
4922 		d = &info->tbufs[i];
4923 
4924 		count = (unsigned short)((size > DMABUFSIZE) ? DMABUFSIZE : size);
4925 		memcpy(d->buf, buf, count);
4926 
4927 		size -= count;
4928 		buf  += count;
4929 
4930 		/*
4931 		 * set EOF bit for last buffer of HDLC frame or
4932 		 * for every buffer in raw mode
4933 		 */
4934 		if ((!size && info->params.mode == MGSL_MODE_HDLC) ||
4935 		    info->params.mode == MGSL_MODE_RAW)
4936 			set_desc_eof(*d, 1);
4937 		else
4938 			set_desc_eof(*d, 0);
4939 
4940 		/* set descriptor count for all but first buffer */
4941 		if (i != info->tbuf_start)
4942 			set_desc_count(*d, count);
4943 		d->buf_count = count;
4944 
4945 		if (++i == info->tbuf_count)
4946 			i = 0;
4947 	}
4948 
4949 	info->tbuf_current = i;
4950 
4951 	/* set first buffer count to make new data visible to DMA controller */
4952 	d = &info->tbufs[info->tbuf_start];
4953 	set_desc_count(*d, d->buf_count);
4954 
4955 	/* start transmitter if needed and update transmit timeout */
4956 	if (!info->tx_active)
4957 		tx_start(info);
4958 	update_tx_timer(info);
4959 
4960 	return true;
4961 }
4962 
4963 static int register_test(struct slgt_info *info)
4964 {
4965 	static unsigned short patterns[] =
4966 		{0x0000, 0xffff, 0xaaaa, 0x5555, 0x6969, 0x9696};
4967 	static unsigned int count = ARRAY_SIZE(patterns);
4968 	unsigned int i;
4969 	int rc = 0;
4970 
4971 	for (i=0 ; i < count ; i++) {
4972 		wr_reg16(info, TIR, patterns[i]);
4973 		wr_reg16(info, BDR, patterns[(i+1)%count]);
4974 		if ((rd_reg16(info, TIR) != patterns[i]) ||
4975 		    (rd_reg16(info, BDR) != patterns[(i+1)%count])) {
4976 			rc = -ENODEV;
4977 			break;
4978 		}
4979 	}
4980 	info->gpio_present = (rd_reg32(info, JCR) & BIT5) ? 1 : 0;
4981 	info->init_error = rc ? 0 : DiagStatus_AddressFailure;
4982 	return rc;
4983 }
4984 
4985 static int irq_test(struct slgt_info *info)
4986 {
4987 	unsigned long timeout;
4988 	unsigned long flags;
4989 	struct tty_struct *oldtty = info->port.tty;
4990 	u32 speed = info->params.data_rate;
4991 
4992 	info->params.data_rate = 921600;
4993 	info->port.tty = NULL;
4994 
4995 	spin_lock_irqsave(&info->lock, flags);
4996 	async_mode(info);
4997 	slgt_irq_on(info, IRQ_TXIDLE);
4998 
4999 	/* enable transmitter */
5000 	wr_reg16(info, TCR,
5001 		(unsigned short)(rd_reg16(info, TCR) | BIT1));
5002 
5003 	/* write one byte and wait for tx idle */
5004 	wr_reg16(info, TDR, 0);
5005 
5006 	/* assume failure */
5007 	info->init_error = DiagStatus_IrqFailure;
5008 	info->irq_occurred = false;
5009 
5010 	spin_unlock_irqrestore(&info->lock, flags);
5011 
5012 	timeout=100;
5013 	while(timeout-- && !info->irq_occurred)
5014 		msleep_interruptible(10);
5015 
5016 	spin_lock_irqsave(&info->lock,flags);
5017 	reset_port(info);
5018 	spin_unlock_irqrestore(&info->lock,flags);
5019 
5020 	info->params.data_rate = speed;
5021 	info->port.tty = oldtty;
5022 
5023 	info->init_error = info->irq_occurred ? 0 : DiagStatus_IrqFailure;
5024 	return info->irq_occurred ? 0 : -ENODEV;
5025 }
5026 
5027 static int loopback_test_rx(struct slgt_info *info)
5028 {
5029 	unsigned char *src, *dest;
5030 	int count;
5031 
5032 	if (desc_complete(info->rbufs[0])) {
5033 		count = desc_count(info->rbufs[0]);
5034 		src   = info->rbufs[0].buf;
5035 		dest  = info->tmp_rbuf;
5036 
5037 		for( ; count ; count-=2, src+=2) {
5038 			/* src=data byte (src+1)=status byte */
5039 			if (!(*(src+1) & (BIT9 + BIT8))) {
5040 				*dest = *src;
5041 				dest++;
5042 				info->tmp_rbuf_count++;
5043 			}
5044 		}
5045 		DBGDATA(info, info->tmp_rbuf, info->tmp_rbuf_count, "rx");
5046 		return 1;
5047 	}
5048 	return 0;
5049 }
5050 
5051 static int loopback_test(struct slgt_info *info)
5052 {
5053 #define TESTFRAMESIZE 20
5054 
5055 	unsigned long timeout;
5056 	u16 count = TESTFRAMESIZE;
5057 	unsigned char buf[TESTFRAMESIZE];
5058 	int rc = -ENODEV;
5059 	unsigned long flags;
5060 
5061 	struct tty_struct *oldtty = info->port.tty;
5062 	MGSL_PARAMS params;
5063 
5064 	memcpy(&params, &info->params, sizeof(params));
5065 
5066 	info->params.mode = MGSL_MODE_ASYNC;
5067 	info->params.data_rate = 921600;
5068 	info->params.loopback = 1;
5069 	info->port.tty = NULL;
5070 
5071 	/* build and send transmit frame */
5072 	for (count = 0; count < TESTFRAMESIZE; ++count)
5073 		buf[count] = (unsigned char)count;
5074 
5075 	info->tmp_rbuf_count = 0;
5076 	memset(info->tmp_rbuf, 0, TESTFRAMESIZE);
5077 
5078 	/* program hardware for HDLC and enabled receiver */
5079 	spin_lock_irqsave(&info->lock,flags);
5080 	async_mode(info);
5081 	rx_start(info);
5082 	tx_load(info, buf, count);
5083 	spin_unlock_irqrestore(&info->lock, flags);
5084 
5085 	/* wait for receive complete */
5086 	for (timeout = 100; timeout; --timeout) {
5087 		msleep_interruptible(10);
5088 		if (loopback_test_rx(info)) {
5089 			rc = 0;
5090 			break;
5091 		}
5092 	}
5093 
5094 	/* verify received frame length and contents */
5095 	if (!rc && (info->tmp_rbuf_count != count ||
5096 		  memcmp(buf, info->tmp_rbuf, count))) {
5097 		rc = -ENODEV;
5098 	}
5099 
5100 	spin_lock_irqsave(&info->lock,flags);
5101 	reset_adapter(info);
5102 	spin_unlock_irqrestore(&info->lock,flags);
5103 
5104 	memcpy(&info->params, &params, sizeof(info->params));
5105 	info->port.tty = oldtty;
5106 
5107 	info->init_error = rc ? DiagStatus_DmaFailure : 0;
5108 	return rc;
5109 }
5110 
5111 static int adapter_test(struct slgt_info *info)
5112 {
5113 	DBGINFO(("testing %s\n", info->device_name));
5114 	if (register_test(info) < 0) {
5115 		printk("register test failure %s addr=%08X\n",
5116 			info->device_name, info->phys_reg_addr);
5117 	} else if (irq_test(info) < 0) {
5118 		printk("IRQ test failure %s IRQ=%d\n",
5119 			info->device_name, info->irq_level);
5120 	} else if (loopback_test(info) < 0) {
5121 		printk("loopback test failure %s\n", info->device_name);
5122 	}
5123 	return info->init_error;
5124 }
5125 
5126 /*
5127  * transmit timeout handler
5128  */
5129 static void tx_timeout(unsigned long context)
5130 {
5131 	struct slgt_info *info = (struct slgt_info*)context;
5132 	unsigned long flags;
5133 
5134 	DBGINFO(("%s tx_timeout\n", info->device_name));
5135 	if(info->tx_active && info->params.mode == MGSL_MODE_HDLC) {
5136 		info->icount.txtimeout++;
5137 	}
5138 	spin_lock_irqsave(&info->lock,flags);
5139 	tx_stop(info);
5140 	spin_unlock_irqrestore(&info->lock,flags);
5141 
5142 #if SYNCLINK_GENERIC_HDLC
5143 	if (info->netcount)
5144 		hdlcdev_tx_done(info);
5145 	else
5146 #endif
5147 		bh_transmit(info);
5148 }
5149 
5150 /*
5151  * receive buffer polling timer
5152  */
5153 static void rx_timeout(unsigned long context)
5154 {
5155 	struct slgt_info *info = (struct slgt_info*)context;
5156 	unsigned long flags;
5157 
5158 	DBGINFO(("%s rx_timeout\n", info->device_name));
5159 	spin_lock_irqsave(&info->lock, flags);
5160 	info->pending_bh |= BH_RECEIVE;
5161 	spin_unlock_irqrestore(&info->lock, flags);
5162 	bh_handler(&info->task);
5163 }
5164 
5165