1 // SPDX-License-Identifier: GPL-2.0 2 /* 3 * Freescale QUICC Engine UART device driver 4 * 5 * Author: Timur Tabi <timur@freescale.com> 6 * 7 * Copyright 2007 Freescale Semiconductor, Inc. 8 * 9 * This driver adds support for UART devices via Freescale's QUICC Engine 10 * found on some Freescale SOCs. 11 * 12 * If Soft-UART support is needed but not already present, then this driver 13 * will request and upload the "Soft-UART" microcode upon probe. The 14 * filename of the microcode should be fsl_qe_ucode_uart_X_YZ.bin, where "X" 15 * is the name of the SOC (e.g. 8323), and YZ is the revision of the SOC, 16 * (e.g. "11" for 1.1). 17 */ 18 19 #include <linux/module.h> 20 #include <linux/serial.h> 21 #include <linux/serial_core.h> 22 #include <linux/slab.h> 23 #include <linux/tty.h> 24 #include <linux/tty_flip.h> 25 #include <linux/io.h> 26 #include <linux/of_address.h> 27 #include <linux/of_irq.h> 28 #include <linux/of_platform.h> 29 #include <linux/dma-mapping.h> 30 31 #include <linux/fs_uart_pd.h> 32 #include <soc/fsl/qe/ucc_slow.h> 33 34 #include <linux/firmware.h> 35 #include <asm/reg.h> 36 37 /* 38 * The GUMR flag for Soft UART. This would normally be defined in qe.h, 39 * but Soft-UART is a hack and we want to keep everything related to it in 40 * this file. 41 */ 42 #define UCC_SLOW_GUMR_H_SUART 0x00004000 /* Soft-UART */ 43 44 /* 45 * soft_uart is 1 if we need to use Soft-UART mode 46 */ 47 static int soft_uart; 48 /* 49 * firmware_loaded is 1 if the firmware has been loaded, 0 otherwise. 50 */ 51 static int firmware_loaded; 52 53 /* Enable this macro to configure all serial ports in internal loopback 54 mode */ 55 /* #define LOOPBACK */ 56 57 /* The major and minor device numbers are defined in 58 * http://www.lanana.org/docs/device-list/devices-2.6+.txt. For the QE 59 * UART, we have major number 204 and minor numbers 46 - 49, which are the 60 * same as for the CPM2. This decision was made because no Freescale part 61 * has both a CPM and a QE. 62 */ 63 #define SERIAL_QE_MAJOR 204 64 #define SERIAL_QE_MINOR 46 65 66 /* Since we only have minor numbers 46 - 49, there is a hard limit of 4 ports */ 67 #define UCC_MAX_UART 4 68 69 /* The number of buffer descriptors for receiving characters. */ 70 #define RX_NUM_FIFO 4 71 72 /* The number of buffer descriptors for transmitting characters. */ 73 #define TX_NUM_FIFO 4 74 75 /* The maximum size of the character buffer for a single RX BD. */ 76 #define RX_BUF_SIZE 32 77 78 /* The maximum size of the character buffer for a single TX BD. */ 79 #define TX_BUF_SIZE 32 80 81 /* 82 * The number of jiffies to wait after receiving a close command before the 83 * device is actually closed. This allows the last few characters to be 84 * sent over the wire. 85 */ 86 #define UCC_WAIT_CLOSING 100 87 88 struct ucc_uart_pram { 89 struct ucc_slow_pram common; 90 u8 res1[8]; /* reserved */ 91 __be16 maxidl; /* Maximum idle chars */ 92 __be16 idlc; /* temp idle counter */ 93 __be16 brkcr; /* Break count register */ 94 __be16 parec; /* receive parity error counter */ 95 __be16 frmec; /* receive framing error counter */ 96 __be16 nosec; /* receive noise counter */ 97 __be16 brkec; /* receive break condition counter */ 98 __be16 brkln; /* last received break length */ 99 __be16 uaddr[2]; /* UART address character 1 & 2 */ 100 __be16 rtemp; /* Temp storage */ 101 __be16 toseq; /* Transmit out of sequence char */ 102 __be16 cchars[8]; /* control characters 1-8 */ 103 __be16 rccm; /* receive control character mask */ 104 __be16 rccr; /* receive control character register */ 105 __be16 rlbc; /* receive last break character */ 106 __be16 res2; /* reserved */ 107 __be32 res3; /* reserved, should be cleared */ 108 u8 res4; /* reserved, should be cleared */ 109 u8 res5[3]; /* reserved, should be cleared */ 110 __be32 res6; /* reserved, should be cleared */ 111 __be32 res7; /* reserved, should be cleared */ 112 __be32 res8; /* reserved, should be cleared */ 113 __be32 res9; /* reserved, should be cleared */ 114 __be32 res10; /* reserved, should be cleared */ 115 __be32 res11; /* reserved, should be cleared */ 116 __be32 res12; /* reserved, should be cleared */ 117 __be32 res13; /* reserved, should be cleared */ 118 /* The rest is for Soft-UART only */ 119 __be16 supsmr; /* 0x90, Shadow UPSMR */ 120 __be16 res92; /* 0x92, reserved, initialize to 0 */ 121 __be32 rx_state; /* 0x94, RX state, initialize to 0 */ 122 __be32 rx_cnt; /* 0x98, RX count, initialize to 0 */ 123 u8 rx_length; /* 0x9C, Char length, set to 1+CL+PEN+1+SL */ 124 u8 rx_bitmark; /* 0x9D, reserved, initialize to 0 */ 125 u8 rx_temp_dlst_qe; /* 0x9E, reserved, initialize to 0 */ 126 u8 res14[0xBC - 0x9F]; /* reserved */ 127 __be32 dump_ptr; /* 0xBC, Dump pointer */ 128 __be32 rx_frame_rem; /* 0xC0, reserved, initialize to 0 */ 129 u8 rx_frame_rem_size; /* 0xC4, reserved, initialize to 0 */ 130 u8 tx_mode; /* 0xC5, mode, 0=AHDLC, 1=UART */ 131 __be16 tx_state; /* 0xC6, TX state */ 132 u8 res15[0xD0 - 0xC8]; /* reserved */ 133 __be32 resD0; /* 0xD0, reserved, initialize to 0 */ 134 u8 resD4; /* 0xD4, reserved, initialize to 0 */ 135 __be16 resD5; /* 0xD5, reserved, initialize to 0 */ 136 } __attribute__ ((packed)); 137 138 /* SUPSMR definitions, for Soft-UART only */ 139 #define UCC_UART_SUPSMR_SL 0x8000 140 #define UCC_UART_SUPSMR_RPM_MASK 0x6000 141 #define UCC_UART_SUPSMR_RPM_ODD 0x0000 142 #define UCC_UART_SUPSMR_RPM_LOW 0x2000 143 #define UCC_UART_SUPSMR_RPM_EVEN 0x4000 144 #define UCC_UART_SUPSMR_RPM_HIGH 0x6000 145 #define UCC_UART_SUPSMR_PEN 0x1000 146 #define UCC_UART_SUPSMR_TPM_MASK 0x0C00 147 #define UCC_UART_SUPSMR_TPM_ODD 0x0000 148 #define UCC_UART_SUPSMR_TPM_LOW 0x0400 149 #define UCC_UART_SUPSMR_TPM_EVEN 0x0800 150 #define UCC_UART_SUPSMR_TPM_HIGH 0x0C00 151 #define UCC_UART_SUPSMR_FRZ 0x0100 152 #define UCC_UART_SUPSMR_UM_MASK 0x00c0 153 #define UCC_UART_SUPSMR_UM_NORMAL 0x0000 154 #define UCC_UART_SUPSMR_UM_MAN_MULTI 0x0040 155 #define UCC_UART_SUPSMR_UM_AUTO_MULTI 0x00c0 156 #define UCC_UART_SUPSMR_CL_MASK 0x0030 157 #define UCC_UART_SUPSMR_CL_8 0x0030 158 #define UCC_UART_SUPSMR_CL_7 0x0020 159 #define UCC_UART_SUPSMR_CL_6 0x0010 160 #define UCC_UART_SUPSMR_CL_5 0x0000 161 162 #define UCC_UART_TX_STATE_AHDLC 0x00 163 #define UCC_UART_TX_STATE_UART 0x01 164 #define UCC_UART_TX_STATE_X1 0x00 165 #define UCC_UART_TX_STATE_X16 0x80 166 167 #define UCC_UART_PRAM_ALIGNMENT 0x100 168 169 #define UCC_UART_SIZE_OF_BD UCC_SLOW_SIZE_OF_BD 170 #define NUM_CONTROL_CHARS 8 171 172 /* Private per-port data structure */ 173 struct uart_qe_port { 174 struct uart_port port; 175 struct ucc_slow __iomem *uccp; 176 struct ucc_uart_pram __iomem *uccup; 177 struct ucc_slow_info us_info; 178 struct ucc_slow_private *us_private; 179 struct device_node *np; 180 unsigned int ucc_num; /* First ucc is 0, not 1 */ 181 182 u16 rx_nrfifos; 183 u16 rx_fifosize; 184 u16 tx_nrfifos; 185 u16 tx_fifosize; 186 int wait_closing; 187 u32 flags; 188 struct qe_bd *rx_bd_base; 189 struct qe_bd *rx_cur; 190 struct qe_bd *tx_bd_base; 191 struct qe_bd *tx_cur; 192 unsigned char *tx_buf; 193 unsigned char *rx_buf; 194 void *bd_virt; /* virtual address of the BD buffers */ 195 dma_addr_t bd_dma_addr; /* bus address of the BD buffers */ 196 unsigned int bd_size; /* size of BD buffer space */ 197 }; 198 199 static struct uart_driver ucc_uart_driver = { 200 .owner = THIS_MODULE, 201 .driver_name = "ucc_uart", 202 .dev_name = "ttyQE", 203 .major = SERIAL_QE_MAJOR, 204 .minor = SERIAL_QE_MINOR, 205 .nr = UCC_MAX_UART, 206 }; 207 208 /* 209 * Virtual to physical address translation. 210 * 211 * Given the virtual address for a character buffer, this function returns 212 * the physical (DMA) equivalent. 213 */ 214 static inline dma_addr_t cpu2qe_addr(void *addr, struct uart_qe_port *qe_port) 215 { 216 if (likely((addr >= qe_port->bd_virt)) && 217 (addr < (qe_port->bd_virt + qe_port->bd_size))) 218 return qe_port->bd_dma_addr + (addr - qe_port->bd_virt); 219 220 /* something nasty happened */ 221 printk(KERN_ERR "%s: addr=%p\n", __func__, addr); 222 BUG(); 223 return 0; 224 } 225 226 /* 227 * Physical to virtual address translation. 228 * 229 * Given the physical (DMA) address for a character buffer, this function 230 * returns the virtual equivalent. 231 */ 232 static inline void *qe2cpu_addr(dma_addr_t addr, struct uart_qe_port *qe_port) 233 { 234 /* sanity check */ 235 if (likely((addr >= qe_port->bd_dma_addr) && 236 (addr < (qe_port->bd_dma_addr + qe_port->bd_size)))) 237 return qe_port->bd_virt + (addr - qe_port->bd_dma_addr); 238 239 /* something nasty happened */ 240 printk(KERN_ERR "%s: addr=%llx\n", __func__, (u64)addr); 241 BUG(); 242 return NULL; 243 } 244 245 /* 246 * Return 1 if the QE is done transmitting all buffers for this port 247 * 248 * This function scans each BD in sequence. If we find a BD that is not 249 * ready (READY=1), then we return 0 indicating that the QE is still sending 250 * data. If we reach the last BD (WRAP=1), then we know we've scanned 251 * the entire list, and all BDs are done. 252 */ 253 static unsigned int qe_uart_tx_empty(struct uart_port *port) 254 { 255 struct uart_qe_port *qe_port = 256 container_of(port, struct uart_qe_port, port); 257 struct qe_bd *bdp = qe_port->tx_bd_base; 258 259 while (1) { 260 if (in_be16(&bdp->status) & BD_SC_READY) 261 /* This BD is not done, so return "not done" */ 262 return 0; 263 264 if (in_be16(&bdp->status) & BD_SC_WRAP) 265 /* 266 * This BD is done and it's the last one, so return 267 * "done" 268 */ 269 return 1; 270 271 bdp++; 272 } 273 } 274 275 /* 276 * Set the modem control lines 277 * 278 * Although the QE can control the modem control lines (e.g. CTS), we 279 * don't need that support. This function must exist, however, otherwise 280 * the kernel will panic. 281 */ 282 void qe_uart_set_mctrl(struct uart_port *port, unsigned int mctrl) 283 { 284 } 285 286 /* 287 * Get the current modem control line status 288 * 289 * Although the QE can control the modem control lines (e.g. CTS), this 290 * driver currently doesn't support that, so we always return Carrier 291 * Detect, Data Set Ready, and Clear To Send. 292 */ 293 static unsigned int qe_uart_get_mctrl(struct uart_port *port) 294 { 295 return TIOCM_CAR | TIOCM_DSR | TIOCM_CTS; 296 } 297 298 /* 299 * Disable the transmit interrupt. 300 * 301 * Although this function is called "stop_tx", it does not actually stop 302 * transmission of data. Instead, it tells the QE to not generate an 303 * interrupt when the UCC is finished sending characters. 304 */ 305 static void qe_uart_stop_tx(struct uart_port *port) 306 { 307 struct uart_qe_port *qe_port = 308 container_of(port, struct uart_qe_port, port); 309 310 clrbits16(&qe_port->uccp->uccm, UCC_UART_UCCE_TX); 311 } 312 313 /* 314 * Transmit as many characters to the HW as possible. 315 * 316 * This function will attempt to stuff of all the characters from the 317 * kernel's transmit buffer into TX BDs. 318 * 319 * A return value of non-zero indicates that it successfully stuffed all 320 * characters from the kernel buffer. 321 * 322 * A return value of zero indicates that there are still characters in the 323 * kernel's buffer that have not been transmitted, but there are no more BDs 324 * available. This function should be called again after a BD has been made 325 * available. 326 */ 327 static int qe_uart_tx_pump(struct uart_qe_port *qe_port) 328 { 329 struct qe_bd *bdp; 330 unsigned char *p; 331 unsigned int count; 332 struct uart_port *port = &qe_port->port; 333 struct circ_buf *xmit = &port->state->xmit; 334 335 bdp = qe_port->rx_cur; 336 337 /* Handle xon/xoff */ 338 if (port->x_char) { 339 /* Pick next descriptor and fill from buffer */ 340 bdp = qe_port->tx_cur; 341 342 p = qe2cpu_addr(bdp->buf, qe_port); 343 344 *p++ = port->x_char; 345 out_be16(&bdp->length, 1); 346 setbits16(&bdp->status, BD_SC_READY); 347 /* Get next BD. */ 348 if (in_be16(&bdp->status) & BD_SC_WRAP) 349 bdp = qe_port->tx_bd_base; 350 else 351 bdp++; 352 qe_port->tx_cur = bdp; 353 354 port->icount.tx++; 355 port->x_char = 0; 356 return 1; 357 } 358 359 if (uart_circ_empty(xmit) || uart_tx_stopped(port)) { 360 qe_uart_stop_tx(port); 361 return 0; 362 } 363 364 /* Pick next descriptor and fill from buffer */ 365 bdp = qe_port->tx_cur; 366 367 while (!(in_be16(&bdp->status) & BD_SC_READY) && 368 (xmit->tail != xmit->head)) { 369 count = 0; 370 p = qe2cpu_addr(bdp->buf, qe_port); 371 while (count < qe_port->tx_fifosize) { 372 *p++ = xmit->buf[xmit->tail]; 373 xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1); 374 port->icount.tx++; 375 count++; 376 if (xmit->head == xmit->tail) 377 break; 378 } 379 380 out_be16(&bdp->length, count); 381 setbits16(&bdp->status, BD_SC_READY); 382 383 /* Get next BD. */ 384 if (in_be16(&bdp->status) & BD_SC_WRAP) 385 bdp = qe_port->tx_bd_base; 386 else 387 bdp++; 388 } 389 qe_port->tx_cur = bdp; 390 391 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) 392 uart_write_wakeup(port); 393 394 if (uart_circ_empty(xmit)) { 395 /* The kernel buffer is empty, so turn off TX interrupts. We 396 don't need to be told when the QE is finished transmitting 397 the data. */ 398 qe_uart_stop_tx(port); 399 return 0; 400 } 401 402 return 1; 403 } 404 405 /* 406 * Start transmitting data 407 * 408 * This function will start transmitting any available data, if the port 409 * isn't already transmitting data. 410 */ 411 static void qe_uart_start_tx(struct uart_port *port) 412 { 413 struct uart_qe_port *qe_port = 414 container_of(port, struct uart_qe_port, port); 415 416 /* If we currently are transmitting, then just return */ 417 if (in_be16(&qe_port->uccp->uccm) & UCC_UART_UCCE_TX) 418 return; 419 420 /* Otherwise, pump the port and start transmission */ 421 if (qe_uart_tx_pump(qe_port)) 422 setbits16(&qe_port->uccp->uccm, UCC_UART_UCCE_TX); 423 } 424 425 /* 426 * Stop transmitting data 427 */ 428 static void qe_uart_stop_rx(struct uart_port *port) 429 { 430 struct uart_qe_port *qe_port = 431 container_of(port, struct uart_qe_port, port); 432 433 clrbits16(&qe_port->uccp->uccm, UCC_UART_UCCE_RX); 434 } 435 436 /* Start or stop sending break signal 437 * 438 * This function controls the sending of a break signal. If break_state=1, 439 * then we start sending a break signal. If break_state=0, then we stop 440 * sending the break signal. 441 */ 442 static void qe_uart_break_ctl(struct uart_port *port, int break_state) 443 { 444 struct uart_qe_port *qe_port = 445 container_of(port, struct uart_qe_port, port); 446 447 if (break_state) 448 ucc_slow_stop_tx(qe_port->us_private); 449 else 450 ucc_slow_restart_tx(qe_port->us_private); 451 } 452 453 /* ISR helper function for receiving character. 454 * 455 * This function is called by the ISR to handling receiving characters 456 */ 457 static void qe_uart_int_rx(struct uart_qe_port *qe_port) 458 { 459 int i; 460 unsigned char ch, *cp; 461 struct uart_port *port = &qe_port->port; 462 struct tty_port *tport = &port->state->port; 463 struct qe_bd *bdp; 464 u16 status; 465 unsigned int flg; 466 467 /* Just loop through the closed BDs and copy the characters into 468 * the buffer. 469 */ 470 bdp = qe_port->rx_cur; 471 while (1) { 472 status = in_be16(&bdp->status); 473 474 /* If this one is empty, then we assume we've read them all */ 475 if (status & BD_SC_EMPTY) 476 break; 477 478 /* get number of characters, and check space in RX buffer */ 479 i = in_be16(&bdp->length); 480 481 /* If we don't have enough room in RX buffer for the entire BD, 482 * then we try later, which will be the next RX interrupt. 483 */ 484 if (tty_buffer_request_room(tport, i) < i) { 485 dev_dbg(port->dev, "ucc-uart: no room in RX buffer\n"); 486 return; 487 } 488 489 /* get pointer */ 490 cp = qe2cpu_addr(bdp->buf, qe_port); 491 492 /* loop through the buffer */ 493 while (i-- > 0) { 494 ch = *cp++; 495 port->icount.rx++; 496 flg = TTY_NORMAL; 497 498 if (!i && status & 499 (BD_SC_BR | BD_SC_FR | BD_SC_PR | BD_SC_OV)) 500 goto handle_error; 501 if (uart_handle_sysrq_char(port, ch)) 502 continue; 503 504 error_return: 505 tty_insert_flip_char(tport, ch, flg); 506 507 } 508 509 /* This BD is ready to be used again. Clear status. get next */ 510 clrsetbits_be16(&bdp->status, BD_SC_BR | BD_SC_FR | BD_SC_PR | 511 BD_SC_OV | BD_SC_ID, BD_SC_EMPTY); 512 if (in_be16(&bdp->status) & BD_SC_WRAP) 513 bdp = qe_port->rx_bd_base; 514 else 515 bdp++; 516 517 } 518 519 /* Write back buffer pointer */ 520 qe_port->rx_cur = bdp; 521 522 /* Activate BH processing */ 523 tty_flip_buffer_push(tport); 524 525 return; 526 527 /* Error processing */ 528 529 handle_error: 530 /* Statistics */ 531 if (status & BD_SC_BR) 532 port->icount.brk++; 533 if (status & BD_SC_PR) 534 port->icount.parity++; 535 if (status & BD_SC_FR) 536 port->icount.frame++; 537 if (status & BD_SC_OV) 538 port->icount.overrun++; 539 540 /* Mask out ignored conditions */ 541 status &= port->read_status_mask; 542 543 /* Handle the remaining ones */ 544 if (status & BD_SC_BR) 545 flg = TTY_BREAK; 546 else if (status & BD_SC_PR) 547 flg = TTY_PARITY; 548 else if (status & BD_SC_FR) 549 flg = TTY_FRAME; 550 551 /* Overrun does not affect the current character ! */ 552 if (status & BD_SC_OV) 553 tty_insert_flip_char(tport, 0, TTY_OVERRUN); 554 #ifdef SUPPORT_SYSRQ 555 port->sysrq = 0; 556 #endif 557 goto error_return; 558 } 559 560 /* Interrupt handler 561 * 562 * This interrupt handler is called after a BD is processed. 563 */ 564 static irqreturn_t qe_uart_int(int irq, void *data) 565 { 566 struct uart_qe_port *qe_port = (struct uart_qe_port *) data; 567 struct ucc_slow __iomem *uccp = qe_port->uccp; 568 u16 events; 569 570 /* Clear the interrupts */ 571 events = in_be16(&uccp->ucce); 572 out_be16(&uccp->ucce, events); 573 574 if (events & UCC_UART_UCCE_BRKE) 575 uart_handle_break(&qe_port->port); 576 577 if (events & UCC_UART_UCCE_RX) 578 qe_uart_int_rx(qe_port); 579 580 if (events & UCC_UART_UCCE_TX) 581 qe_uart_tx_pump(qe_port); 582 583 return events ? IRQ_HANDLED : IRQ_NONE; 584 } 585 586 /* Initialize buffer descriptors 587 * 588 * This function initializes all of the RX and TX buffer descriptors. 589 */ 590 static void qe_uart_initbd(struct uart_qe_port *qe_port) 591 { 592 int i; 593 void *bd_virt; 594 struct qe_bd *bdp; 595 596 /* Set the physical address of the host memory buffers in the buffer 597 * descriptors, and the virtual address for us to work with. 598 */ 599 bd_virt = qe_port->bd_virt; 600 bdp = qe_port->rx_bd_base; 601 qe_port->rx_cur = qe_port->rx_bd_base; 602 for (i = 0; i < (qe_port->rx_nrfifos - 1); i++) { 603 out_be16(&bdp->status, BD_SC_EMPTY | BD_SC_INTRPT); 604 out_be32(&bdp->buf, cpu2qe_addr(bd_virt, qe_port)); 605 out_be16(&bdp->length, 0); 606 bd_virt += qe_port->rx_fifosize; 607 bdp++; 608 } 609 610 /* */ 611 out_be16(&bdp->status, BD_SC_WRAP | BD_SC_EMPTY | BD_SC_INTRPT); 612 out_be32(&bdp->buf, cpu2qe_addr(bd_virt, qe_port)); 613 out_be16(&bdp->length, 0); 614 615 /* Set the physical address of the host memory 616 * buffers in the buffer descriptors, and the 617 * virtual address for us to work with. 618 */ 619 bd_virt = qe_port->bd_virt + 620 L1_CACHE_ALIGN(qe_port->rx_nrfifos * qe_port->rx_fifosize); 621 qe_port->tx_cur = qe_port->tx_bd_base; 622 bdp = qe_port->tx_bd_base; 623 for (i = 0; i < (qe_port->tx_nrfifos - 1); i++) { 624 out_be16(&bdp->status, BD_SC_INTRPT); 625 out_be32(&bdp->buf, cpu2qe_addr(bd_virt, qe_port)); 626 out_be16(&bdp->length, 0); 627 bd_virt += qe_port->tx_fifosize; 628 bdp++; 629 } 630 631 /* Loopback requires the preamble bit to be set on the first TX BD */ 632 #ifdef LOOPBACK 633 setbits16(&qe_port->tx_cur->status, BD_SC_P); 634 #endif 635 636 out_be16(&bdp->status, BD_SC_WRAP | BD_SC_INTRPT); 637 out_be32(&bdp->buf, cpu2qe_addr(bd_virt, qe_port)); 638 out_be16(&bdp->length, 0); 639 } 640 641 /* 642 * Initialize a UCC for UART. 643 * 644 * This function configures a given UCC to be used as a UART device. Basic 645 * UCC initialization is handled in qe_uart_request_port(). This function 646 * does all the UART-specific stuff. 647 */ 648 static void qe_uart_init_ucc(struct uart_qe_port *qe_port) 649 { 650 u32 cecr_subblock; 651 struct ucc_slow __iomem *uccp = qe_port->uccp; 652 struct ucc_uart_pram *uccup = qe_port->uccup; 653 654 unsigned int i; 655 656 /* First, disable TX and RX in the UCC */ 657 ucc_slow_disable(qe_port->us_private, COMM_DIR_RX_AND_TX); 658 659 /* Program the UCC UART parameter RAM */ 660 out_8(&uccup->common.rbmr, UCC_BMR_GBL | UCC_BMR_BO_BE); 661 out_8(&uccup->common.tbmr, UCC_BMR_GBL | UCC_BMR_BO_BE); 662 out_be16(&uccup->common.mrblr, qe_port->rx_fifosize); 663 out_be16(&uccup->maxidl, 0x10); 664 out_be16(&uccup->brkcr, 1); 665 out_be16(&uccup->parec, 0); 666 out_be16(&uccup->frmec, 0); 667 out_be16(&uccup->nosec, 0); 668 out_be16(&uccup->brkec, 0); 669 out_be16(&uccup->uaddr[0], 0); 670 out_be16(&uccup->uaddr[1], 0); 671 out_be16(&uccup->toseq, 0); 672 for (i = 0; i < 8; i++) 673 out_be16(&uccup->cchars[i], 0xC000); 674 out_be16(&uccup->rccm, 0xc0ff); 675 676 /* Configure the GUMR registers for UART */ 677 if (soft_uart) { 678 /* Soft-UART requires a 1X multiplier for TX */ 679 clrsetbits_be32(&uccp->gumr_l, 680 UCC_SLOW_GUMR_L_MODE_MASK | UCC_SLOW_GUMR_L_TDCR_MASK | 681 UCC_SLOW_GUMR_L_RDCR_MASK, 682 UCC_SLOW_GUMR_L_MODE_UART | UCC_SLOW_GUMR_L_TDCR_1 | 683 UCC_SLOW_GUMR_L_RDCR_16); 684 685 clrsetbits_be32(&uccp->gumr_h, UCC_SLOW_GUMR_H_RFW, 686 UCC_SLOW_GUMR_H_TRX | UCC_SLOW_GUMR_H_TTX); 687 } else { 688 clrsetbits_be32(&uccp->gumr_l, 689 UCC_SLOW_GUMR_L_MODE_MASK | UCC_SLOW_GUMR_L_TDCR_MASK | 690 UCC_SLOW_GUMR_L_RDCR_MASK, 691 UCC_SLOW_GUMR_L_MODE_UART | UCC_SLOW_GUMR_L_TDCR_16 | 692 UCC_SLOW_GUMR_L_RDCR_16); 693 694 clrsetbits_be32(&uccp->gumr_h, 695 UCC_SLOW_GUMR_H_TRX | UCC_SLOW_GUMR_H_TTX, 696 UCC_SLOW_GUMR_H_RFW); 697 } 698 699 #ifdef LOOPBACK 700 clrsetbits_be32(&uccp->gumr_l, UCC_SLOW_GUMR_L_DIAG_MASK, 701 UCC_SLOW_GUMR_L_DIAG_LOOP); 702 clrsetbits_be32(&uccp->gumr_h, 703 UCC_SLOW_GUMR_H_CTSP | UCC_SLOW_GUMR_H_RSYN, 704 UCC_SLOW_GUMR_H_CDS); 705 #endif 706 707 /* Disable rx interrupts and clear all pending events. */ 708 out_be16(&uccp->uccm, 0); 709 out_be16(&uccp->ucce, 0xffff); 710 out_be16(&uccp->udsr, 0x7e7e); 711 712 /* Initialize UPSMR */ 713 out_be16(&uccp->upsmr, 0); 714 715 if (soft_uart) { 716 out_be16(&uccup->supsmr, 0x30); 717 out_be16(&uccup->res92, 0); 718 out_be32(&uccup->rx_state, 0); 719 out_be32(&uccup->rx_cnt, 0); 720 out_8(&uccup->rx_bitmark, 0); 721 out_8(&uccup->rx_length, 10); 722 out_be32(&uccup->dump_ptr, 0x4000); 723 out_8(&uccup->rx_temp_dlst_qe, 0); 724 out_be32(&uccup->rx_frame_rem, 0); 725 out_8(&uccup->rx_frame_rem_size, 0); 726 /* Soft-UART requires TX to be 1X */ 727 out_8(&uccup->tx_mode, 728 UCC_UART_TX_STATE_UART | UCC_UART_TX_STATE_X1); 729 out_be16(&uccup->tx_state, 0); 730 out_8(&uccup->resD4, 0); 731 out_be16(&uccup->resD5, 0); 732 733 /* Set UART mode. 734 * Enable receive and transmit. 735 */ 736 737 /* From the microcode errata: 738 * 1.GUMR_L register, set mode=0010 (QMC). 739 * 2.Set GUMR_H[17] bit. (UART/AHDLC mode). 740 * 3.Set GUMR_H[19:20] (Transparent mode) 741 * 4.Clear GUMR_H[26] (RFW) 742 * ... 743 * 6.Receiver must use 16x over sampling 744 */ 745 clrsetbits_be32(&uccp->gumr_l, 746 UCC_SLOW_GUMR_L_MODE_MASK | UCC_SLOW_GUMR_L_TDCR_MASK | 747 UCC_SLOW_GUMR_L_RDCR_MASK, 748 UCC_SLOW_GUMR_L_MODE_QMC | UCC_SLOW_GUMR_L_TDCR_16 | 749 UCC_SLOW_GUMR_L_RDCR_16); 750 751 clrsetbits_be32(&uccp->gumr_h, 752 UCC_SLOW_GUMR_H_RFW | UCC_SLOW_GUMR_H_RSYN, 753 UCC_SLOW_GUMR_H_SUART | UCC_SLOW_GUMR_H_TRX | 754 UCC_SLOW_GUMR_H_TTX | UCC_SLOW_GUMR_H_TFL); 755 756 #ifdef LOOPBACK 757 clrsetbits_be32(&uccp->gumr_l, UCC_SLOW_GUMR_L_DIAG_MASK, 758 UCC_SLOW_GUMR_L_DIAG_LOOP); 759 clrbits32(&uccp->gumr_h, UCC_SLOW_GUMR_H_CTSP | 760 UCC_SLOW_GUMR_H_CDS); 761 #endif 762 763 cecr_subblock = ucc_slow_get_qe_cr_subblock(qe_port->ucc_num); 764 qe_issue_cmd(QE_INIT_TX_RX, cecr_subblock, 765 QE_CR_PROTOCOL_UNSPECIFIED, 0); 766 } else { 767 cecr_subblock = ucc_slow_get_qe_cr_subblock(qe_port->ucc_num); 768 qe_issue_cmd(QE_INIT_TX_RX, cecr_subblock, 769 QE_CR_PROTOCOL_UART, 0); 770 } 771 } 772 773 /* 774 * Initialize the port. 775 */ 776 static int qe_uart_startup(struct uart_port *port) 777 { 778 struct uart_qe_port *qe_port = 779 container_of(port, struct uart_qe_port, port); 780 int ret; 781 782 /* 783 * If we're using Soft-UART mode, then we need to make sure the 784 * firmware has been uploaded first. 785 */ 786 if (soft_uart && !firmware_loaded) { 787 dev_err(port->dev, "Soft-UART firmware not uploaded\n"); 788 return -ENODEV; 789 } 790 791 qe_uart_initbd(qe_port); 792 qe_uart_init_ucc(qe_port); 793 794 /* Install interrupt handler. */ 795 ret = request_irq(port->irq, qe_uart_int, IRQF_SHARED, "ucc-uart", 796 qe_port); 797 if (ret) { 798 dev_err(port->dev, "could not claim IRQ %u\n", port->irq); 799 return ret; 800 } 801 802 /* Startup rx-int */ 803 setbits16(&qe_port->uccp->uccm, UCC_UART_UCCE_RX); 804 ucc_slow_enable(qe_port->us_private, COMM_DIR_RX_AND_TX); 805 806 return 0; 807 } 808 809 /* 810 * Shutdown the port. 811 */ 812 static void qe_uart_shutdown(struct uart_port *port) 813 { 814 struct uart_qe_port *qe_port = 815 container_of(port, struct uart_qe_port, port); 816 struct ucc_slow __iomem *uccp = qe_port->uccp; 817 unsigned int timeout = 20; 818 819 /* Disable RX and TX */ 820 821 /* Wait for all the BDs marked sent */ 822 while (!qe_uart_tx_empty(port)) { 823 if (!--timeout) { 824 dev_warn(port->dev, "shutdown timeout\n"); 825 break; 826 } 827 set_current_state(TASK_UNINTERRUPTIBLE); 828 schedule_timeout(2); 829 } 830 831 if (qe_port->wait_closing) { 832 /* Wait a bit longer */ 833 set_current_state(TASK_UNINTERRUPTIBLE); 834 schedule_timeout(qe_port->wait_closing); 835 } 836 837 /* Stop uarts */ 838 ucc_slow_disable(qe_port->us_private, COMM_DIR_RX_AND_TX); 839 clrbits16(&uccp->uccm, UCC_UART_UCCE_TX | UCC_UART_UCCE_RX); 840 841 /* Shut them really down and reinit buffer descriptors */ 842 ucc_slow_graceful_stop_tx(qe_port->us_private); 843 qe_uart_initbd(qe_port); 844 845 free_irq(port->irq, qe_port); 846 } 847 848 /* 849 * Set the serial port parameters. 850 */ 851 static void qe_uart_set_termios(struct uart_port *port, 852 struct ktermios *termios, struct ktermios *old) 853 { 854 struct uart_qe_port *qe_port = 855 container_of(port, struct uart_qe_port, port); 856 struct ucc_slow __iomem *uccp = qe_port->uccp; 857 unsigned int baud; 858 unsigned long flags; 859 u16 upsmr = in_be16(&uccp->upsmr); 860 struct ucc_uart_pram __iomem *uccup = qe_port->uccup; 861 u16 supsmr = in_be16(&uccup->supsmr); 862 u8 char_length = 2; /* 1 + CL + PEN + 1 + SL */ 863 864 /* Character length programmed into the mode register is the 865 * sum of: 1 start bit, number of data bits, 0 or 1 parity bit, 866 * 1 or 2 stop bits, minus 1. 867 * The value 'bits' counts this for us. 868 */ 869 870 /* byte size */ 871 upsmr &= UCC_UART_UPSMR_CL_MASK; 872 supsmr &= UCC_UART_SUPSMR_CL_MASK; 873 874 switch (termios->c_cflag & CSIZE) { 875 case CS5: 876 upsmr |= UCC_UART_UPSMR_CL_5; 877 supsmr |= UCC_UART_SUPSMR_CL_5; 878 char_length += 5; 879 break; 880 case CS6: 881 upsmr |= UCC_UART_UPSMR_CL_6; 882 supsmr |= UCC_UART_SUPSMR_CL_6; 883 char_length += 6; 884 break; 885 case CS7: 886 upsmr |= UCC_UART_UPSMR_CL_7; 887 supsmr |= UCC_UART_SUPSMR_CL_7; 888 char_length += 7; 889 break; 890 default: /* case CS8 */ 891 upsmr |= UCC_UART_UPSMR_CL_8; 892 supsmr |= UCC_UART_SUPSMR_CL_8; 893 char_length += 8; 894 break; 895 } 896 897 /* If CSTOPB is set, we want two stop bits */ 898 if (termios->c_cflag & CSTOPB) { 899 upsmr |= UCC_UART_UPSMR_SL; 900 supsmr |= UCC_UART_SUPSMR_SL; 901 char_length++; /* + SL */ 902 } 903 904 if (termios->c_cflag & PARENB) { 905 upsmr |= UCC_UART_UPSMR_PEN; 906 supsmr |= UCC_UART_SUPSMR_PEN; 907 char_length++; /* + PEN */ 908 909 if (!(termios->c_cflag & PARODD)) { 910 upsmr &= ~(UCC_UART_UPSMR_RPM_MASK | 911 UCC_UART_UPSMR_TPM_MASK); 912 upsmr |= UCC_UART_UPSMR_RPM_EVEN | 913 UCC_UART_UPSMR_TPM_EVEN; 914 supsmr &= ~(UCC_UART_SUPSMR_RPM_MASK | 915 UCC_UART_SUPSMR_TPM_MASK); 916 supsmr |= UCC_UART_SUPSMR_RPM_EVEN | 917 UCC_UART_SUPSMR_TPM_EVEN; 918 } 919 } 920 921 /* 922 * Set up parity check flag 923 */ 924 port->read_status_mask = BD_SC_EMPTY | BD_SC_OV; 925 if (termios->c_iflag & INPCK) 926 port->read_status_mask |= BD_SC_FR | BD_SC_PR; 927 if (termios->c_iflag & (IGNBRK | BRKINT | PARMRK)) 928 port->read_status_mask |= BD_SC_BR; 929 930 /* 931 * Characters to ignore 932 */ 933 port->ignore_status_mask = 0; 934 if (termios->c_iflag & IGNPAR) 935 port->ignore_status_mask |= BD_SC_PR | BD_SC_FR; 936 if (termios->c_iflag & IGNBRK) { 937 port->ignore_status_mask |= BD_SC_BR; 938 /* 939 * If we're ignore parity and break indicators, ignore 940 * overruns too. (For real raw support). 941 */ 942 if (termios->c_iflag & IGNPAR) 943 port->ignore_status_mask |= BD_SC_OV; 944 } 945 /* 946 * !!! ignore all characters if CREAD is not set 947 */ 948 if ((termios->c_cflag & CREAD) == 0) 949 port->read_status_mask &= ~BD_SC_EMPTY; 950 951 baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk / 16); 952 953 /* Do we really need a spinlock here? */ 954 spin_lock_irqsave(&port->lock, flags); 955 956 /* Update the per-port timeout. */ 957 uart_update_timeout(port, termios->c_cflag, baud); 958 959 out_be16(&uccp->upsmr, upsmr); 960 if (soft_uart) { 961 out_be16(&uccup->supsmr, supsmr); 962 out_8(&uccup->rx_length, char_length); 963 964 /* Soft-UART requires a 1X multiplier for TX */ 965 qe_setbrg(qe_port->us_info.rx_clock, baud, 16); 966 qe_setbrg(qe_port->us_info.tx_clock, baud, 1); 967 } else { 968 qe_setbrg(qe_port->us_info.rx_clock, baud, 16); 969 qe_setbrg(qe_port->us_info.tx_clock, baud, 16); 970 } 971 972 spin_unlock_irqrestore(&port->lock, flags); 973 } 974 975 /* 976 * Return a pointer to a string that describes what kind of port this is. 977 */ 978 static const char *qe_uart_type(struct uart_port *port) 979 { 980 return "QE"; 981 } 982 983 /* 984 * Allocate any memory and I/O resources required by the port. 985 */ 986 static int qe_uart_request_port(struct uart_port *port) 987 { 988 int ret; 989 struct uart_qe_port *qe_port = 990 container_of(port, struct uart_qe_port, port); 991 struct ucc_slow_info *us_info = &qe_port->us_info; 992 struct ucc_slow_private *uccs; 993 unsigned int rx_size, tx_size; 994 void *bd_virt; 995 dma_addr_t bd_dma_addr = 0; 996 997 ret = ucc_slow_init(us_info, &uccs); 998 if (ret) { 999 dev_err(port->dev, "could not initialize UCC%u\n", 1000 qe_port->ucc_num); 1001 return ret; 1002 } 1003 1004 qe_port->us_private = uccs; 1005 qe_port->uccp = uccs->us_regs; 1006 qe_port->uccup = (struct ucc_uart_pram *) uccs->us_pram; 1007 qe_port->rx_bd_base = uccs->rx_bd; 1008 qe_port->tx_bd_base = uccs->tx_bd; 1009 1010 /* 1011 * Allocate the transmit and receive data buffers. 1012 */ 1013 1014 rx_size = L1_CACHE_ALIGN(qe_port->rx_nrfifos * qe_port->rx_fifosize); 1015 tx_size = L1_CACHE_ALIGN(qe_port->tx_nrfifos * qe_port->tx_fifosize); 1016 1017 bd_virt = dma_alloc_coherent(port->dev, rx_size + tx_size, &bd_dma_addr, 1018 GFP_KERNEL); 1019 if (!bd_virt) { 1020 dev_err(port->dev, "could not allocate buffer descriptors\n"); 1021 return -ENOMEM; 1022 } 1023 1024 qe_port->bd_virt = bd_virt; 1025 qe_port->bd_dma_addr = bd_dma_addr; 1026 qe_port->bd_size = rx_size + tx_size; 1027 1028 qe_port->rx_buf = bd_virt; 1029 qe_port->tx_buf = qe_port->rx_buf + rx_size; 1030 1031 return 0; 1032 } 1033 1034 /* 1035 * Configure the port. 1036 * 1037 * We say we're a CPM-type port because that's mostly true. Once the device 1038 * is configured, this driver operates almost identically to the CPM serial 1039 * driver. 1040 */ 1041 static void qe_uart_config_port(struct uart_port *port, int flags) 1042 { 1043 if (flags & UART_CONFIG_TYPE) { 1044 port->type = PORT_CPM; 1045 qe_uart_request_port(port); 1046 } 1047 } 1048 1049 /* 1050 * Release any memory and I/O resources that were allocated in 1051 * qe_uart_request_port(). 1052 */ 1053 static void qe_uart_release_port(struct uart_port *port) 1054 { 1055 struct uart_qe_port *qe_port = 1056 container_of(port, struct uart_qe_port, port); 1057 struct ucc_slow_private *uccs = qe_port->us_private; 1058 1059 dma_free_coherent(port->dev, qe_port->bd_size, qe_port->bd_virt, 1060 qe_port->bd_dma_addr); 1061 1062 ucc_slow_free(uccs); 1063 } 1064 1065 /* 1066 * Verify that the data in serial_struct is suitable for this device. 1067 */ 1068 static int qe_uart_verify_port(struct uart_port *port, 1069 struct serial_struct *ser) 1070 { 1071 if (ser->type != PORT_UNKNOWN && ser->type != PORT_CPM) 1072 return -EINVAL; 1073 1074 if (ser->irq < 0 || ser->irq >= nr_irqs) 1075 return -EINVAL; 1076 1077 if (ser->baud_base < 9600) 1078 return -EINVAL; 1079 1080 return 0; 1081 } 1082 /* UART operations 1083 * 1084 * Details on these functions can be found in Documentation/serial/driver 1085 */ 1086 static const struct uart_ops qe_uart_pops = { 1087 .tx_empty = qe_uart_tx_empty, 1088 .set_mctrl = qe_uart_set_mctrl, 1089 .get_mctrl = qe_uart_get_mctrl, 1090 .stop_tx = qe_uart_stop_tx, 1091 .start_tx = qe_uart_start_tx, 1092 .stop_rx = qe_uart_stop_rx, 1093 .break_ctl = qe_uart_break_ctl, 1094 .startup = qe_uart_startup, 1095 .shutdown = qe_uart_shutdown, 1096 .set_termios = qe_uart_set_termios, 1097 .type = qe_uart_type, 1098 .release_port = qe_uart_release_port, 1099 .request_port = qe_uart_request_port, 1100 .config_port = qe_uart_config_port, 1101 .verify_port = qe_uart_verify_port, 1102 }; 1103 1104 /* 1105 * Obtain the SOC model number and revision level 1106 * 1107 * This function parses the device tree to obtain the SOC model. It then 1108 * reads the SVR register to the revision. 1109 * 1110 * The device tree stores the SOC model two different ways. 1111 * 1112 * The new way is: 1113 * 1114 * cpu@0 { 1115 * compatible = "PowerPC,8323"; 1116 * device_type = "cpu"; 1117 * ... 1118 * 1119 * 1120 * The old way is: 1121 * PowerPC,8323@0 { 1122 * device_type = "cpu"; 1123 * ... 1124 * 1125 * This code first checks the new way, and then the old way. 1126 */ 1127 static unsigned int soc_info(unsigned int *rev_h, unsigned int *rev_l) 1128 { 1129 struct device_node *np; 1130 const char *soc_string; 1131 unsigned int svr; 1132 unsigned int soc; 1133 1134 /* Find the CPU node */ 1135 np = of_find_node_by_type(NULL, "cpu"); 1136 if (!np) 1137 return 0; 1138 /* Find the compatible property */ 1139 soc_string = of_get_property(np, "compatible", NULL); 1140 if (!soc_string) 1141 /* No compatible property, so try the name. */ 1142 soc_string = np->name; 1143 1144 /* Extract the SOC number from the "PowerPC," string */ 1145 if ((sscanf(soc_string, "PowerPC,%u", &soc) != 1) || !soc) 1146 return 0; 1147 1148 /* Get the revision from the SVR */ 1149 svr = mfspr(SPRN_SVR); 1150 *rev_h = (svr >> 4) & 0xf; 1151 *rev_l = svr & 0xf; 1152 1153 return soc; 1154 } 1155 1156 /* 1157 * requst_firmware_nowait() callback function 1158 * 1159 * This function is called by the kernel when a firmware is made available, 1160 * or if it times out waiting for the firmware. 1161 */ 1162 static void uart_firmware_cont(const struct firmware *fw, void *context) 1163 { 1164 struct qe_firmware *firmware; 1165 struct device *dev = context; 1166 int ret; 1167 1168 if (!fw) { 1169 dev_err(dev, "firmware not found\n"); 1170 return; 1171 } 1172 1173 firmware = (struct qe_firmware *) fw->data; 1174 1175 if (firmware->header.length != fw->size) { 1176 dev_err(dev, "invalid firmware\n"); 1177 goto out; 1178 } 1179 1180 ret = qe_upload_firmware(firmware); 1181 if (ret) { 1182 dev_err(dev, "could not load firmware\n"); 1183 goto out; 1184 } 1185 1186 firmware_loaded = 1; 1187 out: 1188 release_firmware(fw); 1189 } 1190 1191 static int ucc_uart_probe(struct platform_device *ofdev) 1192 { 1193 struct device_node *np = ofdev->dev.of_node; 1194 const unsigned int *iprop; /* Integer OF properties */ 1195 const char *sprop; /* String OF properties */ 1196 struct uart_qe_port *qe_port = NULL; 1197 struct resource res; 1198 int ret; 1199 1200 /* 1201 * Determine if we need Soft-UART mode 1202 */ 1203 if (of_find_property(np, "soft-uart", NULL)) { 1204 dev_dbg(&ofdev->dev, "using Soft-UART mode\n"); 1205 soft_uart = 1; 1206 } 1207 1208 /* 1209 * If we are using Soft-UART, determine if we need to upload the 1210 * firmware, too. 1211 */ 1212 if (soft_uart) { 1213 struct qe_firmware_info *qe_fw_info; 1214 1215 qe_fw_info = qe_get_firmware_info(); 1216 1217 /* Check if the firmware has been uploaded. */ 1218 if (qe_fw_info && strstr(qe_fw_info->id, "Soft-UART")) { 1219 firmware_loaded = 1; 1220 } else { 1221 char filename[32]; 1222 unsigned int soc; 1223 unsigned int rev_h; 1224 unsigned int rev_l; 1225 1226 soc = soc_info(&rev_h, &rev_l); 1227 if (!soc) { 1228 dev_err(&ofdev->dev, "unknown CPU model\n"); 1229 return -ENXIO; 1230 } 1231 sprintf(filename, "fsl_qe_ucode_uart_%u_%u%u.bin", 1232 soc, rev_h, rev_l); 1233 1234 dev_info(&ofdev->dev, "waiting for firmware %s\n", 1235 filename); 1236 1237 /* 1238 * We call request_firmware_nowait instead of 1239 * request_firmware so that the driver can load and 1240 * initialize the ports without holding up the rest of 1241 * the kernel. If hotplug support is enabled in the 1242 * kernel, then we use it. 1243 */ 1244 ret = request_firmware_nowait(THIS_MODULE, 1245 FW_ACTION_HOTPLUG, filename, &ofdev->dev, 1246 GFP_KERNEL, &ofdev->dev, uart_firmware_cont); 1247 if (ret) { 1248 dev_err(&ofdev->dev, 1249 "could not load firmware %s\n", 1250 filename); 1251 return ret; 1252 } 1253 } 1254 } 1255 1256 qe_port = kzalloc(sizeof(struct uart_qe_port), GFP_KERNEL); 1257 if (!qe_port) { 1258 dev_err(&ofdev->dev, "can't allocate QE port structure\n"); 1259 return -ENOMEM; 1260 } 1261 1262 /* Search for IRQ and mapbase */ 1263 ret = of_address_to_resource(np, 0, &res); 1264 if (ret) { 1265 dev_err(&ofdev->dev, "missing 'reg' property in device tree\n"); 1266 goto out_free; 1267 } 1268 if (!res.start) { 1269 dev_err(&ofdev->dev, "invalid 'reg' property in device tree\n"); 1270 ret = -EINVAL; 1271 goto out_free; 1272 } 1273 qe_port->port.mapbase = res.start; 1274 1275 /* Get the UCC number (device ID) */ 1276 /* UCCs are numbered 1-7 */ 1277 iprop = of_get_property(np, "cell-index", NULL); 1278 if (!iprop) { 1279 iprop = of_get_property(np, "device-id", NULL); 1280 if (!iprop) { 1281 dev_err(&ofdev->dev, "UCC is unspecified in " 1282 "device tree\n"); 1283 ret = -EINVAL; 1284 goto out_free; 1285 } 1286 } 1287 1288 if ((*iprop < 1) || (*iprop > UCC_MAX_NUM)) { 1289 dev_err(&ofdev->dev, "no support for UCC%u\n", *iprop); 1290 ret = -ENODEV; 1291 goto out_free; 1292 } 1293 qe_port->ucc_num = *iprop - 1; 1294 1295 /* 1296 * In the future, we should not require the BRG to be specified in the 1297 * device tree. If no clock-source is specified, then just pick a BRG 1298 * to use. This requires a new QE library function that manages BRG 1299 * assignments. 1300 */ 1301 1302 sprop = of_get_property(np, "rx-clock-name", NULL); 1303 if (!sprop) { 1304 dev_err(&ofdev->dev, "missing rx-clock-name in device tree\n"); 1305 ret = -ENODEV; 1306 goto out_free; 1307 } 1308 1309 qe_port->us_info.rx_clock = qe_clock_source(sprop); 1310 if ((qe_port->us_info.rx_clock < QE_BRG1) || 1311 (qe_port->us_info.rx_clock > QE_BRG16)) { 1312 dev_err(&ofdev->dev, "rx-clock-name must be a BRG for UART\n"); 1313 ret = -ENODEV; 1314 goto out_free; 1315 } 1316 1317 #ifdef LOOPBACK 1318 /* In internal loopback mode, TX and RX must use the same clock */ 1319 qe_port->us_info.tx_clock = qe_port->us_info.rx_clock; 1320 #else 1321 sprop = of_get_property(np, "tx-clock-name", NULL); 1322 if (!sprop) { 1323 dev_err(&ofdev->dev, "missing tx-clock-name in device tree\n"); 1324 ret = -ENODEV; 1325 goto out_free; 1326 } 1327 qe_port->us_info.tx_clock = qe_clock_source(sprop); 1328 #endif 1329 if ((qe_port->us_info.tx_clock < QE_BRG1) || 1330 (qe_port->us_info.tx_clock > QE_BRG16)) { 1331 dev_err(&ofdev->dev, "tx-clock-name must be a BRG for UART\n"); 1332 ret = -ENODEV; 1333 goto out_free; 1334 } 1335 1336 /* Get the port number, numbered 0-3 */ 1337 iprop = of_get_property(np, "port-number", NULL); 1338 if (!iprop) { 1339 dev_err(&ofdev->dev, "missing port-number in device tree\n"); 1340 ret = -EINVAL; 1341 goto out_free; 1342 } 1343 qe_port->port.line = *iprop; 1344 if (qe_port->port.line >= UCC_MAX_UART) { 1345 dev_err(&ofdev->dev, "port-number must be 0-%u\n", 1346 UCC_MAX_UART - 1); 1347 ret = -EINVAL; 1348 goto out_free; 1349 } 1350 1351 qe_port->port.irq = irq_of_parse_and_map(np, 0); 1352 if (qe_port->port.irq == 0) { 1353 dev_err(&ofdev->dev, "could not map IRQ for UCC%u\n", 1354 qe_port->ucc_num + 1); 1355 ret = -EINVAL; 1356 goto out_free; 1357 } 1358 1359 /* 1360 * Newer device trees have an "fsl,qe" compatible property for the QE 1361 * node, but we still need to support older device trees. 1362 */ 1363 np = of_find_compatible_node(NULL, NULL, "fsl,qe"); 1364 if (!np) { 1365 np = of_find_node_by_type(NULL, "qe"); 1366 if (!np) { 1367 dev_err(&ofdev->dev, "could not find 'qe' node\n"); 1368 ret = -EINVAL; 1369 goto out_free; 1370 } 1371 } 1372 1373 iprop = of_get_property(np, "brg-frequency", NULL); 1374 if (!iprop) { 1375 dev_err(&ofdev->dev, 1376 "missing brg-frequency in device tree\n"); 1377 ret = -EINVAL; 1378 goto out_np; 1379 } 1380 1381 if (*iprop) 1382 qe_port->port.uartclk = *iprop; 1383 else { 1384 /* 1385 * Older versions of U-Boot do not initialize the brg-frequency 1386 * property, so in this case we assume the BRG frequency is 1387 * half the QE bus frequency. 1388 */ 1389 iprop = of_get_property(np, "bus-frequency", NULL); 1390 if (!iprop) { 1391 dev_err(&ofdev->dev, 1392 "missing QE bus-frequency in device tree\n"); 1393 ret = -EINVAL; 1394 goto out_np; 1395 } 1396 if (*iprop) 1397 qe_port->port.uartclk = *iprop / 2; 1398 else { 1399 dev_err(&ofdev->dev, 1400 "invalid QE bus-frequency in device tree\n"); 1401 ret = -EINVAL; 1402 goto out_np; 1403 } 1404 } 1405 1406 spin_lock_init(&qe_port->port.lock); 1407 qe_port->np = np; 1408 qe_port->port.dev = &ofdev->dev; 1409 qe_port->port.ops = &qe_uart_pops; 1410 qe_port->port.iotype = UPIO_MEM; 1411 1412 qe_port->tx_nrfifos = TX_NUM_FIFO; 1413 qe_port->tx_fifosize = TX_BUF_SIZE; 1414 qe_port->rx_nrfifos = RX_NUM_FIFO; 1415 qe_port->rx_fifosize = RX_BUF_SIZE; 1416 1417 qe_port->wait_closing = UCC_WAIT_CLOSING; 1418 qe_port->port.fifosize = 512; 1419 qe_port->port.flags = UPF_BOOT_AUTOCONF | UPF_IOREMAP; 1420 1421 qe_port->us_info.ucc_num = qe_port->ucc_num; 1422 qe_port->us_info.regs = (phys_addr_t) res.start; 1423 qe_port->us_info.irq = qe_port->port.irq; 1424 1425 qe_port->us_info.rx_bd_ring_len = qe_port->rx_nrfifos; 1426 qe_port->us_info.tx_bd_ring_len = qe_port->tx_nrfifos; 1427 1428 /* Make sure ucc_slow_init() initializes both TX and RX */ 1429 qe_port->us_info.init_tx = 1; 1430 qe_port->us_info.init_rx = 1; 1431 1432 /* Add the port to the uart sub-system. This will cause 1433 * qe_uart_config_port() to be called, so the us_info structure must 1434 * be initialized. 1435 */ 1436 ret = uart_add_one_port(&ucc_uart_driver, &qe_port->port); 1437 if (ret) { 1438 dev_err(&ofdev->dev, "could not add /dev/ttyQE%u\n", 1439 qe_port->port.line); 1440 goto out_np; 1441 } 1442 1443 platform_set_drvdata(ofdev, qe_port); 1444 1445 dev_info(&ofdev->dev, "UCC%u assigned to /dev/ttyQE%u\n", 1446 qe_port->ucc_num + 1, qe_port->port.line); 1447 1448 /* Display the mknod command for this device */ 1449 dev_dbg(&ofdev->dev, "mknod command is 'mknod /dev/ttyQE%u c %u %u'\n", 1450 qe_port->port.line, SERIAL_QE_MAJOR, 1451 SERIAL_QE_MINOR + qe_port->port.line); 1452 1453 return 0; 1454 out_np: 1455 of_node_put(np); 1456 out_free: 1457 kfree(qe_port); 1458 return ret; 1459 } 1460 1461 static int ucc_uart_remove(struct platform_device *ofdev) 1462 { 1463 struct uart_qe_port *qe_port = platform_get_drvdata(ofdev); 1464 1465 dev_info(&ofdev->dev, "removing /dev/ttyQE%u\n", qe_port->port.line); 1466 1467 uart_remove_one_port(&ucc_uart_driver, &qe_port->port); 1468 1469 kfree(qe_port); 1470 1471 return 0; 1472 } 1473 1474 static const struct of_device_id ucc_uart_match[] = { 1475 { 1476 .type = "serial", 1477 .compatible = "ucc_uart", 1478 }, 1479 { 1480 .compatible = "fsl,t1040-ucc-uart", 1481 }, 1482 {}, 1483 }; 1484 MODULE_DEVICE_TABLE(of, ucc_uart_match); 1485 1486 static struct platform_driver ucc_uart_of_driver = { 1487 .driver = { 1488 .name = "ucc_uart", 1489 .of_match_table = ucc_uart_match, 1490 }, 1491 .probe = ucc_uart_probe, 1492 .remove = ucc_uart_remove, 1493 }; 1494 1495 static int __init ucc_uart_init(void) 1496 { 1497 int ret; 1498 1499 printk(KERN_INFO "Freescale QUICC Engine UART device driver\n"); 1500 #ifdef LOOPBACK 1501 printk(KERN_INFO "ucc-uart: Using loopback mode\n"); 1502 #endif 1503 1504 ret = uart_register_driver(&ucc_uart_driver); 1505 if (ret) { 1506 printk(KERN_ERR "ucc-uart: could not register UART driver\n"); 1507 return ret; 1508 } 1509 1510 ret = platform_driver_register(&ucc_uart_of_driver); 1511 if (ret) { 1512 printk(KERN_ERR 1513 "ucc-uart: could not register platform driver\n"); 1514 uart_unregister_driver(&ucc_uart_driver); 1515 } 1516 1517 return ret; 1518 } 1519 1520 static void __exit ucc_uart_exit(void) 1521 { 1522 printk(KERN_INFO 1523 "Freescale QUICC Engine UART device driver unloading\n"); 1524 1525 platform_driver_unregister(&ucc_uart_of_driver); 1526 uart_unregister_driver(&ucc_uart_driver); 1527 } 1528 1529 module_init(ucc_uart_init); 1530 module_exit(ucc_uart_exit); 1531 1532 MODULE_DESCRIPTION("Freescale QUICC Engine (QE) UART"); 1533 MODULE_AUTHOR("Timur Tabi <timur@freescale.com>"); 1534 MODULE_LICENSE("GPL v2"); 1535 MODULE_ALIAS_CHARDEV_MAJOR(SERIAL_QE_MAJOR); 1536 1537