1 // SPDX-License-Identifier: GPL-2.0 2 /* sunzilog.c: Zilog serial driver for Sparc systems. 3 * 4 * Driver for Zilog serial chips found on Sun workstations and 5 * servers. This driver could actually be made more generic. 6 * 7 * This is based on the old drivers/sbus/char/zs.c code. A lot 8 * of code has been simply moved over directly from there but 9 * much has been rewritten. Credits therefore go out to Eddie 10 * C. Dost, Pete Zaitcev, Ted Ts'o and Alex Buell for their 11 * work there. 12 * 13 * Copyright (C) 2002, 2006, 2007 David S. Miller (davem@davemloft.net) 14 */ 15 16 #include <linux/module.h> 17 #include <linux/kernel.h> 18 #include <linux/errno.h> 19 #include <linux/delay.h> 20 #include <linux/tty.h> 21 #include <linux/tty_flip.h> 22 #include <linux/major.h> 23 #include <linux/string.h> 24 #include <linux/ptrace.h> 25 #include <linux/ioport.h> 26 #include <linux/slab.h> 27 #include <linux/circ_buf.h> 28 #include <linux/serial.h> 29 #include <linux/sysrq.h> 30 #include <linux/console.h> 31 #include <linux/spinlock.h> 32 #ifdef CONFIG_SERIO 33 #include <linux/serio.h> 34 #endif 35 #include <linux/init.h> 36 #include <linux/of.h> 37 #include <linux/platform_device.h> 38 39 #include <linux/io.h> 40 #include <asm/irq.h> 41 #include <asm/setup.h> 42 43 #include <linux/serial_core.h> 44 #include <linux/sunserialcore.h> 45 46 #include "sunzilog.h" 47 48 /* On 32-bit sparcs we need to delay after register accesses 49 * to accommodate sun4 systems, but we do not need to flush writes. 50 * On 64-bit sparc we only need to flush single writes to ensure 51 * completion. 52 */ 53 #ifndef CONFIG_SPARC64 54 #define ZSDELAY() udelay(5) 55 #define ZSDELAY_LONG() udelay(20) 56 #define ZS_WSYNC(channel) do { } while (0) 57 #else 58 #define ZSDELAY() 59 #define ZSDELAY_LONG() 60 #define ZS_WSYNC(__channel) \ 61 readb(&((__channel)->control)) 62 #endif 63 64 #define ZS_CLOCK 4915200 /* Zilog input clock rate. */ 65 #define ZS_CLOCK_DIVISOR 16 /* Divisor this driver uses. */ 66 67 /* 68 * We wrap our port structure around the generic uart_port. 69 */ 70 struct uart_sunzilog_port { 71 struct uart_port port; 72 73 /* IRQ servicing chain. */ 74 struct uart_sunzilog_port *next; 75 76 /* Current values of Zilog write registers. */ 77 unsigned char curregs[NUM_ZSREGS]; 78 79 unsigned int flags; 80 #define SUNZILOG_FLAG_CONS_KEYB 0x00000001 81 #define SUNZILOG_FLAG_CONS_MOUSE 0x00000002 82 #define SUNZILOG_FLAG_IS_CONS 0x00000004 83 #define SUNZILOG_FLAG_IS_KGDB 0x00000008 84 #define SUNZILOG_FLAG_MODEM_STATUS 0x00000010 85 #define SUNZILOG_FLAG_IS_CHANNEL_A 0x00000020 86 #define SUNZILOG_FLAG_REGS_HELD 0x00000040 87 #define SUNZILOG_FLAG_TX_STOPPED 0x00000080 88 #define SUNZILOG_FLAG_TX_ACTIVE 0x00000100 89 #define SUNZILOG_FLAG_ESCC 0x00000200 90 #define SUNZILOG_FLAG_ISR_HANDLER 0x00000400 91 92 unsigned int cflag; 93 94 unsigned char parity_mask; 95 unsigned char prev_status; 96 97 #ifdef CONFIG_SERIO 98 struct serio serio; 99 int serio_open; 100 #endif 101 }; 102 103 static void sunzilog_putchar(struct uart_port *port, unsigned char ch); 104 105 #define ZILOG_CHANNEL_FROM_PORT(PORT) ((struct zilog_channel __iomem *)((PORT)->membase)) 106 #define UART_ZILOG(PORT) ((struct uart_sunzilog_port *)(PORT)) 107 108 #define ZS_IS_KEYB(UP) ((UP)->flags & SUNZILOG_FLAG_CONS_KEYB) 109 #define ZS_IS_MOUSE(UP) ((UP)->flags & SUNZILOG_FLAG_CONS_MOUSE) 110 #define ZS_IS_CONS(UP) ((UP)->flags & SUNZILOG_FLAG_IS_CONS) 111 #define ZS_IS_KGDB(UP) ((UP)->flags & SUNZILOG_FLAG_IS_KGDB) 112 #define ZS_WANTS_MODEM_STATUS(UP) ((UP)->flags & SUNZILOG_FLAG_MODEM_STATUS) 113 #define ZS_IS_CHANNEL_A(UP) ((UP)->flags & SUNZILOG_FLAG_IS_CHANNEL_A) 114 #define ZS_REGS_HELD(UP) ((UP)->flags & SUNZILOG_FLAG_REGS_HELD) 115 #define ZS_TX_STOPPED(UP) ((UP)->flags & SUNZILOG_FLAG_TX_STOPPED) 116 #define ZS_TX_ACTIVE(UP) ((UP)->flags & SUNZILOG_FLAG_TX_ACTIVE) 117 118 /* Reading and writing Zilog8530 registers. The delays are to make this 119 * driver work on the Sun4 which needs a settling delay after each chip 120 * register access, other machines handle this in hardware via auxiliary 121 * flip-flops which implement the settle time we do in software. 122 * 123 * The port lock must be held and local IRQs must be disabled 124 * when {read,write}_zsreg is invoked. 125 */ 126 static unsigned char read_zsreg(struct zilog_channel __iomem *channel, 127 unsigned char reg) 128 { 129 unsigned char retval; 130 131 writeb(reg, &channel->control); 132 ZSDELAY(); 133 retval = readb(&channel->control); 134 ZSDELAY(); 135 136 return retval; 137 } 138 139 static void write_zsreg(struct zilog_channel __iomem *channel, 140 unsigned char reg, unsigned char value) 141 { 142 writeb(reg, &channel->control); 143 ZSDELAY(); 144 writeb(value, &channel->control); 145 ZSDELAY(); 146 } 147 148 static void sunzilog_clear_fifo(struct zilog_channel __iomem *channel) 149 { 150 int i; 151 152 for (i = 0; i < 32; i++) { 153 unsigned char regval; 154 155 regval = readb(&channel->control); 156 ZSDELAY(); 157 if (regval & Rx_CH_AV) 158 break; 159 160 regval = read_zsreg(channel, R1); 161 readb(&channel->data); 162 ZSDELAY(); 163 164 if (regval & (PAR_ERR | Rx_OVR | CRC_ERR)) { 165 writeb(ERR_RES, &channel->control); 166 ZSDELAY(); 167 ZS_WSYNC(channel); 168 } 169 } 170 } 171 172 /* This function must only be called when the TX is not busy. The UART 173 * port lock must be held and local interrupts disabled. 174 */ 175 static int __load_zsregs(struct zilog_channel __iomem *channel, unsigned char *regs) 176 { 177 int i; 178 int escc; 179 unsigned char r15; 180 181 /* Let pending transmits finish. */ 182 for (i = 0; i < 1000; i++) { 183 unsigned char stat = read_zsreg(channel, R1); 184 if (stat & ALL_SNT) 185 break; 186 udelay(100); 187 } 188 189 writeb(ERR_RES, &channel->control); 190 ZSDELAY(); 191 ZS_WSYNC(channel); 192 193 sunzilog_clear_fifo(channel); 194 195 /* Disable all interrupts. */ 196 write_zsreg(channel, R1, 197 regs[R1] & ~(RxINT_MASK | TxINT_ENAB | EXT_INT_ENAB)); 198 199 /* Set parity, sync config, stop bits, and clock divisor. */ 200 write_zsreg(channel, R4, regs[R4]); 201 202 /* Set misc. TX/RX control bits. */ 203 write_zsreg(channel, R10, regs[R10]); 204 205 /* Set TX/RX controls sans the enable bits. */ 206 write_zsreg(channel, R3, regs[R3] & ~RxENAB); 207 write_zsreg(channel, R5, regs[R5] & ~TxENAB); 208 209 /* Synchronous mode config. */ 210 write_zsreg(channel, R6, regs[R6]); 211 write_zsreg(channel, R7, regs[R7]); 212 213 /* Don't mess with the interrupt vector (R2, unused by us) and 214 * master interrupt control (R9). We make sure this is setup 215 * properly at probe time then never touch it again. 216 */ 217 218 /* Disable baud generator. */ 219 write_zsreg(channel, R14, regs[R14] & ~BRENAB); 220 221 /* Clock mode control. */ 222 write_zsreg(channel, R11, regs[R11]); 223 224 /* Lower and upper byte of baud rate generator divisor. */ 225 write_zsreg(channel, R12, regs[R12]); 226 write_zsreg(channel, R13, regs[R13]); 227 228 /* Now rewrite R14, with BRENAB (if set). */ 229 write_zsreg(channel, R14, regs[R14]); 230 231 /* External status interrupt control. */ 232 write_zsreg(channel, R15, (regs[R15] | WR7pEN) & ~FIFOEN); 233 234 /* ESCC Extension Register */ 235 r15 = read_zsreg(channel, R15); 236 if (r15 & 0x01) { 237 write_zsreg(channel, R7, regs[R7p]); 238 239 /* External status interrupt and FIFO control. */ 240 write_zsreg(channel, R15, regs[R15] & ~WR7pEN); 241 escc = 1; 242 } else { 243 /* Clear FIFO bit case it is an issue */ 244 regs[R15] &= ~FIFOEN; 245 escc = 0; 246 } 247 248 /* Reset external status interrupts. */ 249 write_zsreg(channel, R0, RES_EXT_INT); /* First Latch */ 250 write_zsreg(channel, R0, RES_EXT_INT); /* Second Latch */ 251 252 /* Rewrite R3/R5, this time without enables masked. */ 253 write_zsreg(channel, R3, regs[R3]); 254 write_zsreg(channel, R5, regs[R5]); 255 256 /* Rewrite R1, this time without IRQ enabled masked. */ 257 write_zsreg(channel, R1, regs[R1]); 258 259 return escc; 260 } 261 262 /* Reprogram the Zilog channel HW registers with the copies found in the 263 * software state struct. If the transmitter is busy, we defer this update 264 * until the next TX complete interrupt. Else, we do it right now. 265 * 266 * The UART port lock must be held and local interrupts disabled. 267 */ 268 static void sunzilog_maybe_update_regs(struct uart_sunzilog_port *up, 269 struct zilog_channel __iomem *channel) 270 { 271 if (!ZS_REGS_HELD(up)) { 272 if (ZS_TX_ACTIVE(up)) { 273 up->flags |= SUNZILOG_FLAG_REGS_HELD; 274 } else { 275 __load_zsregs(channel, up->curregs); 276 } 277 } 278 } 279 280 static void sunzilog_change_mouse_baud(struct uart_sunzilog_port *up) 281 { 282 unsigned int cur_cflag = up->cflag; 283 int brg, new_baud; 284 285 up->cflag &= ~CBAUD; 286 up->cflag |= suncore_mouse_baud_cflag_next(cur_cflag, &new_baud); 287 288 brg = BPS_TO_BRG(new_baud, ZS_CLOCK / ZS_CLOCK_DIVISOR); 289 up->curregs[R12] = (brg & 0xff); 290 up->curregs[R13] = (brg >> 8) & 0xff; 291 sunzilog_maybe_update_regs(up, ZILOG_CHANNEL_FROM_PORT(&up->port)); 292 } 293 294 static void sunzilog_kbdms_receive_chars(struct uart_sunzilog_port *up, 295 unsigned char ch, int is_break) 296 { 297 if (ZS_IS_KEYB(up)) { 298 /* Stop-A is handled by drivers/char/keyboard.c now. */ 299 #ifdef CONFIG_SERIO 300 if (up->serio_open) 301 serio_interrupt(&up->serio, ch, 0); 302 #endif 303 } else if (ZS_IS_MOUSE(up)) { 304 int ret = suncore_mouse_baud_detection(ch, is_break); 305 306 switch (ret) { 307 case 2: 308 sunzilog_change_mouse_baud(up); 309 fallthrough; 310 case 1: 311 break; 312 313 case 0: 314 #ifdef CONFIG_SERIO 315 if (up->serio_open) 316 serio_interrupt(&up->serio, ch, 0); 317 #endif 318 break; 319 } 320 } 321 } 322 323 static struct tty_port * 324 sunzilog_receive_chars(struct uart_sunzilog_port *up, 325 struct zilog_channel __iomem *channel) 326 { 327 struct tty_port *port = NULL; 328 unsigned char ch, r1, flag; 329 330 if (up->port.state != NULL) /* Unopened serial console */ 331 port = &up->port.state->port; 332 333 for (;;) { 334 335 r1 = read_zsreg(channel, R1); 336 if (r1 & (PAR_ERR | Rx_OVR | CRC_ERR)) { 337 writeb(ERR_RES, &channel->control); 338 ZSDELAY(); 339 ZS_WSYNC(channel); 340 } 341 342 ch = readb(&channel->control); 343 ZSDELAY(); 344 345 /* This funny hack depends upon BRK_ABRT not interfering 346 * with the other bits we care about in R1. 347 */ 348 if (ch & BRK_ABRT) 349 r1 |= BRK_ABRT; 350 351 if (!(ch & Rx_CH_AV)) 352 break; 353 354 ch = readb(&channel->data); 355 ZSDELAY(); 356 357 ch &= up->parity_mask; 358 359 if (unlikely(ZS_IS_KEYB(up)) || unlikely(ZS_IS_MOUSE(up))) { 360 sunzilog_kbdms_receive_chars(up, ch, 0); 361 continue; 362 } 363 364 /* A real serial line, record the character and status. */ 365 flag = TTY_NORMAL; 366 up->port.icount.rx++; 367 if (r1 & (BRK_ABRT | PAR_ERR | Rx_OVR | CRC_ERR)) { 368 if (r1 & BRK_ABRT) { 369 r1 &= ~(PAR_ERR | CRC_ERR); 370 up->port.icount.brk++; 371 if (uart_handle_break(&up->port)) 372 continue; 373 } 374 else if (r1 & PAR_ERR) 375 up->port.icount.parity++; 376 else if (r1 & CRC_ERR) 377 up->port.icount.frame++; 378 if (r1 & Rx_OVR) 379 up->port.icount.overrun++; 380 r1 &= up->port.read_status_mask; 381 if (r1 & BRK_ABRT) 382 flag = TTY_BREAK; 383 else if (r1 & PAR_ERR) 384 flag = TTY_PARITY; 385 else if (r1 & CRC_ERR) 386 flag = TTY_FRAME; 387 } 388 if (uart_handle_sysrq_char(&up->port, ch) || !port) 389 continue; 390 391 if (up->port.ignore_status_mask == 0xff || 392 (r1 & up->port.ignore_status_mask) == 0) { 393 tty_insert_flip_char(port, ch, flag); 394 } 395 if (r1 & Rx_OVR) 396 tty_insert_flip_char(port, 0, TTY_OVERRUN); 397 } 398 399 return port; 400 } 401 402 static void sunzilog_status_handle(struct uart_sunzilog_port *up, 403 struct zilog_channel __iomem *channel) 404 { 405 unsigned char status; 406 407 status = readb(&channel->control); 408 ZSDELAY(); 409 410 writeb(RES_EXT_INT, &channel->control); 411 ZSDELAY(); 412 ZS_WSYNC(channel); 413 414 if (status & BRK_ABRT) { 415 if (ZS_IS_MOUSE(up)) 416 sunzilog_kbdms_receive_chars(up, 0, 1); 417 if (ZS_IS_CONS(up)) { 418 /* Wait for BREAK to deassert to avoid potentially 419 * confusing the PROM. 420 */ 421 while (1) { 422 status = readb(&channel->control); 423 ZSDELAY(); 424 if (!(status & BRK_ABRT)) 425 break; 426 } 427 sun_do_break(); 428 return; 429 } 430 } 431 432 if (ZS_WANTS_MODEM_STATUS(up)) { 433 if (status & SYNC) 434 up->port.icount.dsr++; 435 436 /* The Zilog just gives us an interrupt when DCD/CTS/etc. change. 437 * But it does not tell us which bit has changed, we have to keep 438 * track of this ourselves. 439 */ 440 if ((status ^ up->prev_status) ^ DCD) 441 uart_handle_dcd_change(&up->port, 442 (status & DCD)); 443 if ((status ^ up->prev_status) ^ CTS) 444 uart_handle_cts_change(&up->port, 445 (status & CTS)); 446 447 wake_up_interruptible(&up->port.state->port.delta_msr_wait); 448 } 449 450 up->prev_status = status; 451 } 452 453 static void sunzilog_transmit_chars(struct uart_sunzilog_port *up, 454 struct zilog_channel __iomem *channel) 455 { 456 struct circ_buf *xmit; 457 458 if (ZS_IS_CONS(up)) { 459 unsigned char status = readb(&channel->control); 460 ZSDELAY(); 461 462 /* TX still busy? Just wait for the next TX done interrupt. 463 * 464 * It can occur because of how we do serial console writes. It would 465 * be nice to transmit console writes just like we normally would for 466 * a TTY line. (ie. buffered and TX interrupt driven). That is not 467 * easy because console writes cannot sleep. One solution might be 468 * to poll on enough port->xmit space becoming free. -DaveM 469 */ 470 if (!(status & Tx_BUF_EMP)) 471 return; 472 } 473 474 up->flags &= ~SUNZILOG_FLAG_TX_ACTIVE; 475 476 if (ZS_REGS_HELD(up)) { 477 __load_zsregs(channel, up->curregs); 478 up->flags &= ~SUNZILOG_FLAG_REGS_HELD; 479 } 480 481 if (ZS_TX_STOPPED(up)) { 482 up->flags &= ~SUNZILOG_FLAG_TX_STOPPED; 483 goto ack_tx_int; 484 } 485 486 if (up->port.x_char) { 487 up->flags |= SUNZILOG_FLAG_TX_ACTIVE; 488 writeb(up->port.x_char, &channel->data); 489 ZSDELAY(); 490 ZS_WSYNC(channel); 491 492 up->port.icount.tx++; 493 up->port.x_char = 0; 494 return; 495 } 496 497 if (up->port.state == NULL) 498 goto ack_tx_int; 499 xmit = &up->port.state->xmit; 500 if (uart_circ_empty(xmit)) 501 goto ack_tx_int; 502 503 if (uart_tx_stopped(&up->port)) 504 goto ack_tx_int; 505 506 up->flags |= SUNZILOG_FLAG_TX_ACTIVE; 507 writeb(xmit->buf[xmit->tail], &channel->data); 508 ZSDELAY(); 509 ZS_WSYNC(channel); 510 511 uart_xmit_advance(&up->port, 1); 512 513 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) 514 uart_write_wakeup(&up->port); 515 516 return; 517 518 ack_tx_int: 519 writeb(RES_Tx_P, &channel->control); 520 ZSDELAY(); 521 ZS_WSYNC(channel); 522 } 523 524 static irqreturn_t sunzilog_interrupt(int irq, void *dev_id) 525 { 526 struct uart_sunzilog_port *up = dev_id; 527 528 while (up) { 529 struct zilog_channel __iomem *channel 530 = ZILOG_CHANNEL_FROM_PORT(&up->port); 531 struct tty_port *port; 532 unsigned char r3; 533 534 spin_lock(&up->port.lock); 535 r3 = read_zsreg(channel, R3); 536 537 /* Channel A */ 538 port = NULL; 539 if (r3 & (CHAEXT | CHATxIP | CHARxIP)) { 540 writeb(RES_H_IUS, &channel->control); 541 ZSDELAY(); 542 ZS_WSYNC(channel); 543 544 if (r3 & CHARxIP) 545 port = sunzilog_receive_chars(up, channel); 546 if (r3 & CHAEXT) 547 sunzilog_status_handle(up, channel); 548 if (r3 & CHATxIP) 549 sunzilog_transmit_chars(up, channel); 550 } 551 spin_unlock(&up->port.lock); 552 553 if (port) 554 tty_flip_buffer_push(port); 555 556 /* Channel B */ 557 up = up->next; 558 channel = ZILOG_CHANNEL_FROM_PORT(&up->port); 559 560 spin_lock(&up->port.lock); 561 port = NULL; 562 if (r3 & (CHBEXT | CHBTxIP | CHBRxIP)) { 563 writeb(RES_H_IUS, &channel->control); 564 ZSDELAY(); 565 ZS_WSYNC(channel); 566 567 if (r3 & CHBRxIP) 568 port = sunzilog_receive_chars(up, channel); 569 if (r3 & CHBEXT) 570 sunzilog_status_handle(up, channel); 571 if (r3 & CHBTxIP) 572 sunzilog_transmit_chars(up, channel); 573 } 574 spin_unlock(&up->port.lock); 575 576 if (port) 577 tty_flip_buffer_push(port); 578 579 up = up->next; 580 } 581 582 return IRQ_HANDLED; 583 } 584 585 /* A convenient way to quickly get R0 status. The caller must _not_ hold the 586 * port lock, it is acquired here. 587 */ 588 static __inline__ unsigned char sunzilog_read_channel_status(struct uart_port *port) 589 { 590 struct zilog_channel __iomem *channel; 591 unsigned char status; 592 593 channel = ZILOG_CHANNEL_FROM_PORT(port); 594 status = readb(&channel->control); 595 ZSDELAY(); 596 597 return status; 598 } 599 600 /* The port lock is not held. */ 601 static unsigned int sunzilog_tx_empty(struct uart_port *port) 602 { 603 unsigned long flags; 604 unsigned char status; 605 unsigned int ret; 606 607 spin_lock_irqsave(&port->lock, flags); 608 609 status = sunzilog_read_channel_status(port); 610 611 spin_unlock_irqrestore(&port->lock, flags); 612 613 if (status & Tx_BUF_EMP) 614 ret = TIOCSER_TEMT; 615 else 616 ret = 0; 617 618 return ret; 619 } 620 621 /* The port lock is held and interrupts are disabled. */ 622 static unsigned int sunzilog_get_mctrl(struct uart_port *port) 623 { 624 unsigned char status; 625 unsigned int ret; 626 627 status = sunzilog_read_channel_status(port); 628 629 ret = 0; 630 if (status & DCD) 631 ret |= TIOCM_CAR; 632 if (status & SYNC) 633 ret |= TIOCM_DSR; 634 if (status & CTS) 635 ret |= TIOCM_CTS; 636 637 return ret; 638 } 639 640 /* The port lock is held and interrupts are disabled. */ 641 static void sunzilog_set_mctrl(struct uart_port *port, unsigned int mctrl) 642 { 643 struct uart_sunzilog_port *up = 644 container_of(port, struct uart_sunzilog_port, port); 645 struct zilog_channel __iomem *channel = ZILOG_CHANNEL_FROM_PORT(port); 646 unsigned char set_bits, clear_bits; 647 648 set_bits = clear_bits = 0; 649 650 if (mctrl & TIOCM_RTS) 651 set_bits |= RTS; 652 else 653 clear_bits |= RTS; 654 if (mctrl & TIOCM_DTR) 655 set_bits |= DTR; 656 else 657 clear_bits |= DTR; 658 659 /* NOTE: Not subject to 'transmitter active' rule. */ 660 up->curregs[R5] |= set_bits; 661 up->curregs[R5] &= ~clear_bits; 662 write_zsreg(channel, R5, up->curregs[R5]); 663 } 664 665 /* The port lock is held and interrupts are disabled. */ 666 static void sunzilog_stop_tx(struct uart_port *port) 667 { 668 struct uart_sunzilog_port *up = 669 container_of(port, struct uart_sunzilog_port, port); 670 671 up->flags |= SUNZILOG_FLAG_TX_STOPPED; 672 } 673 674 /* The port lock is held and interrupts are disabled. */ 675 static void sunzilog_start_tx(struct uart_port *port) 676 { 677 struct uart_sunzilog_port *up = 678 container_of(port, struct uart_sunzilog_port, port); 679 struct zilog_channel __iomem *channel = ZILOG_CHANNEL_FROM_PORT(port); 680 unsigned char status; 681 682 up->flags |= SUNZILOG_FLAG_TX_ACTIVE; 683 up->flags &= ~SUNZILOG_FLAG_TX_STOPPED; 684 685 status = readb(&channel->control); 686 ZSDELAY(); 687 688 /* TX busy? Just wait for the TX done interrupt. */ 689 if (!(status & Tx_BUF_EMP)) 690 return; 691 692 /* Send the first character to jump-start the TX done 693 * IRQ sending engine. 694 */ 695 if (port->x_char) { 696 writeb(port->x_char, &channel->data); 697 ZSDELAY(); 698 ZS_WSYNC(channel); 699 700 port->icount.tx++; 701 port->x_char = 0; 702 } else { 703 struct circ_buf *xmit = &port->state->xmit; 704 705 if (uart_circ_empty(xmit)) 706 return; 707 writeb(xmit->buf[xmit->tail], &channel->data); 708 ZSDELAY(); 709 ZS_WSYNC(channel); 710 711 uart_xmit_advance(port, 1); 712 713 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) 714 uart_write_wakeup(&up->port); 715 } 716 } 717 718 /* The port lock is held. */ 719 static void sunzilog_stop_rx(struct uart_port *port) 720 { 721 struct uart_sunzilog_port *up = UART_ZILOG(port); 722 struct zilog_channel __iomem *channel; 723 724 if (ZS_IS_CONS(up)) 725 return; 726 727 channel = ZILOG_CHANNEL_FROM_PORT(port); 728 729 /* Disable all RX interrupts. */ 730 up->curregs[R1] &= ~RxINT_MASK; 731 sunzilog_maybe_update_regs(up, channel); 732 } 733 734 /* The port lock is held. */ 735 static void sunzilog_enable_ms(struct uart_port *port) 736 { 737 struct uart_sunzilog_port *up = 738 container_of(port, struct uart_sunzilog_port, port); 739 struct zilog_channel __iomem *channel = ZILOG_CHANNEL_FROM_PORT(port); 740 unsigned char new_reg; 741 742 new_reg = up->curregs[R15] | (DCDIE | SYNCIE | CTSIE); 743 if (new_reg != up->curregs[R15]) { 744 up->curregs[R15] = new_reg; 745 746 /* NOTE: Not subject to 'transmitter active' rule. */ 747 write_zsreg(channel, R15, up->curregs[R15] & ~WR7pEN); 748 } 749 } 750 751 /* The port lock is not held. */ 752 static void sunzilog_break_ctl(struct uart_port *port, int break_state) 753 { 754 struct uart_sunzilog_port *up = 755 container_of(port, struct uart_sunzilog_port, port); 756 struct zilog_channel __iomem *channel = ZILOG_CHANNEL_FROM_PORT(port); 757 unsigned char set_bits, clear_bits, new_reg; 758 unsigned long flags; 759 760 set_bits = clear_bits = 0; 761 762 if (break_state) 763 set_bits |= SND_BRK; 764 else 765 clear_bits |= SND_BRK; 766 767 spin_lock_irqsave(&port->lock, flags); 768 769 new_reg = (up->curregs[R5] | set_bits) & ~clear_bits; 770 if (new_reg != up->curregs[R5]) { 771 up->curregs[R5] = new_reg; 772 773 /* NOTE: Not subject to 'transmitter active' rule. */ 774 write_zsreg(channel, R5, up->curregs[R5]); 775 } 776 777 spin_unlock_irqrestore(&port->lock, flags); 778 } 779 780 static void __sunzilog_startup(struct uart_sunzilog_port *up) 781 { 782 struct zilog_channel __iomem *channel; 783 784 channel = ZILOG_CHANNEL_FROM_PORT(&up->port); 785 up->prev_status = readb(&channel->control); 786 787 /* Enable receiver and transmitter. */ 788 up->curregs[R3] |= RxENAB; 789 up->curregs[R5] |= TxENAB; 790 791 up->curregs[R1] |= EXT_INT_ENAB | INT_ALL_Rx | TxINT_ENAB; 792 sunzilog_maybe_update_regs(up, channel); 793 } 794 795 static int sunzilog_startup(struct uart_port *port) 796 { 797 struct uart_sunzilog_port *up = UART_ZILOG(port); 798 unsigned long flags; 799 800 if (ZS_IS_CONS(up)) 801 return 0; 802 803 spin_lock_irqsave(&port->lock, flags); 804 __sunzilog_startup(up); 805 spin_unlock_irqrestore(&port->lock, flags); 806 return 0; 807 } 808 809 /* 810 * The test for ZS_IS_CONS is explained by the following e-mail: 811 ***** 812 * From: Russell King <rmk@arm.linux.org.uk> 813 * Date: Sun, 8 Dec 2002 10:18:38 +0000 814 * 815 * On Sun, Dec 08, 2002 at 02:43:36AM -0500, Pete Zaitcev wrote: 816 * > I boot my 2.5 boxes using "console=ttyS0,9600" argument, 817 * > and I noticed that something is not right with reference 818 * > counting in this case. It seems that when the console 819 * > is open by kernel initially, this is not accounted 820 * > as an open, and uart_startup is not called. 821 * 822 * That is correct. We are unable to call uart_startup when the serial 823 * console is initialised because it may need to allocate memory (as 824 * request_irq does) and the memory allocators may not have been 825 * initialised. 826 * 827 * 1. initialise the port into a state where it can send characters in the 828 * console write method. 829 * 830 * 2. don't do the actual hardware shutdown in your shutdown() method (but 831 * do the normal software shutdown - ie, free irqs etc) 832 ***** 833 */ 834 static void sunzilog_shutdown(struct uart_port *port) 835 { 836 struct uart_sunzilog_port *up = UART_ZILOG(port); 837 struct zilog_channel __iomem *channel; 838 unsigned long flags; 839 840 if (ZS_IS_CONS(up)) 841 return; 842 843 spin_lock_irqsave(&port->lock, flags); 844 845 channel = ZILOG_CHANNEL_FROM_PORT(port); 846 847 /* Disable receiver and transmitter. */ 848 up->curregs[R3] &= ~RxENAB; 849 up->curregs[R5] &= ~TxENAB; 850 851 /* Disable all interrupts and BRK assertion. */ 852 up->curregs[R1] &= ~(EXT_INT_ENAB | TxINT_ENAB | RxINT_MASK); 853 up->curregs[R5] &= ~SND_BRK; 854 sunzilog_maybe_update_regs(up, channel); 855 856 spin_unlock_irqrestore(&port->lock, flags); 857 } 858 859 /* Shared by TTY driver and serial console setup. The port lock is held 860 * and local interrupts are disabled. 861 */ 862 static void 863 sunzilog_convert_to_zs(struct uart_sunzilog_port *up, unsigned int cflag, 864 unsigned int iflag, int brg) 865 { 866 867 up->curregs[R10] = NRZ; 868 up->curregs[R11] = TCBR | RCBR; 869 870 /* Program BAUD and clock source. */ 871 up->curregs[R4] &= ~XCLK_MASK; 872 up->curregs[R4] |= X16CLK; 873 up->curregs[R12] = brg & 0xff; 874 up->curregs[R13] = (brg >> 8) & 0xff; 875 up->curregs[R14] = BRSRC | BRENAB; 876 877 /* Character size, stop bits, and parity. */ 878 up->curregs[R3] &= ~RxN_MASK; 879 up->curregs[R5] &= ~TxN_MASK; 880 switch (cflag & CSIZE) { 881 case CS5: 882 up->curregs[R3] |= Rx5; 883 up->curregs[R5] |= Tx5; 884 up->parity_mask = 0x1f; 885 break; 886 case CS6: 887 up->curregs[R3] |= Rx6; 888 up->curregs[R5] |= Tx6; 889 up->parity_mask = 0x3f; 890 break; 891 case CS7: 892 up->curregs[R3] |= Rx7; 893 up->curregs[R5] |= Tx7; 894 up->parity_mask = 0x7f; 895 break; 896 case CS8: 897 default: 898 up->curregs[R3] |= Rx8; 899 up->curregs[R5] |= Tx8; 900 up->parity_mask = 0xff; 901 break; 902 } 903 up->curregs[R4] &= ~0x0c; 904 if (cflag & CSTOPB) 905 up->curregs[R4] |= SB2; 906 else 907 up->curregs[R4] |= SB1; 908 if (cflag & PARENB) 909 up->curregs[R4] |= PAR_ENAB; 910 else 911 up->curregs[R4] &= ~PAR_ENAB; 912 if (!(cflag & PARODD)) 913 up->curregs[R4] |= PAR_EVEN; 914 else 915 up->curregs[R4] &= ~PAR_EVEN; 916 917 up->port.read_status_mask = Rx_OVR; 918 if (iflag & INPCK) 919 up->port.read_status_mask |= CRC_ERR | PAR_ERR; 920 if (iflag & (IGNBRK | BRKINT | PARMRK)) 921 up->port.read_status_mask |= BRK_ABRT; 922 923 up->port.ignore_status_mask = 0; 924 if (iflag & IGNPAR) 925 up->port.ignore_status_mask |= CRC_ERR | PAR_ERR; 926 if (iflag & IGNBRK) { 927 up->port.ignore_status_mask |= BRK_ABRT; 928 if (iflag & IGNPAR) 929 up->port.ignore_status_mask |= Rx_OVR; 930 } 931 932 if ((cflag & CREAD) == 0) 933 up->port.ignore_status_mask = 0xff; 934 } 935 936 /* The port lock is not held. */ 937 static void 938 sunzilog_set_termios(struct uart_port *port, struct ktermios *termios, 939 const struct ktermios *old) 940 { 941 struct uart_sunzilog_port *up = 942 container_of(port, struct uart_sunzilog_port, port); 943 unsigned long flags; 944 int baud, brg; 945 946 baud = uart_get_baud_rate(port, termios, old, 1200, 76800); 947 948 spin_lock_irqsave(&up->port.lock, flags); 949 950 brg = BPS_TO_BRG(baud, ZS_CLOCK / ZS_CLOCK_DIVISOR); 951 952 sunzilog_convert_to_zs(up, termios->c_cflag, termios->c_iflag, brg); 953 954 if (UART_ENABLE_MS(&up->port, termios->c_cflag)) 955 up->flags |= SUNZILOG_FLAG_MODEM_STATUS; 956 else 957 up->flags &= ~SUNZILOG_FLAG_MODEM_STATUS; 958 959 up->cflag = termios->c_cflag; 960 961 sunzilog_maybe_update_regs(up, ZILOG_CHANNEL_FROM_PORT(port)); 962 963 uart_update_timeout(port, termios->c_cflag, baud); 964 965 spin_unlock_irqrestore(&up->port.lock, flags); 966 } 967 968 static const char *sunzilog_type(struct uart_port *port) 969 { 970 struct uart_sunzilog_port *up = UART_ZILOG(port); 971 972 return (up->flags & SUNZILOG_FLAG_ESCC) ? "zs (ESCC)" : "zs"; 973 } 974 975 /* We do not request/release mappings of the registers here, this 976 * happens at early serial probe time. 977 */ 978 static void sunzilog_release_port(struct uart_port *port) 979 { 980 } 981 982 static int sunzilog_request_port(struct uart_port *port) 983 { 984 return 0; 985 } 986 987 /* These do not need to do anything interesting either. */ 988 static void sunzilog_config_port(struct uart_port *port, int flags) 989 { 990 } 991 992 /* We do not support letting the user mess with the divisor, IRQ, etc. */ 993 static int sunzilog_verify_port(struct uart_port *port, struct serial_struct *ser) 994 { 995 return -EINVAL; 996 } 997 998 #ifdef CONFIG_CONSOLE_POLL 999 static int sunzilog_get_poll_char(struct uart_port *port) 1000 { 1001 unsigned char ch, r1; 1002 struct uart_sunzilog_port *up = 1003 container_of(port, struct uart_sunzilog_port, port); 1004 struct zilog_channel __iomem *channel 1005 = ZILOG_CHANNEL_FROM_PORT(&up->port); 1006 1007 1008 r1 = read_zsreg(channel, R1); 1009 if (r1 & (PAR_ERR | Rx_OVR | CRC_ERR)) { 1010 writeb(ERR_RES, &channel->control); 1011 ZSDELAY(); 1012 ZS_WSYNC(channel); 1013 } 1014 1015 ch = readb(&channel->control); 1016 ZSDELAY(); 1017 1018 /* This funny hack depends upon BRK_ABRT not interfering 1019 * with the other bits we care about in R1. 1020 */ 1021 if (ch & BRK_ABRT) 1022 r1 |= BRK_ABRT; 1023 1024 if (!(ch & Rx_CH_AV)) 1025 return NO_POLL_CHAR; 1026 1027 ch = readb(&channel->data); 1028 ZSDELAY(); 1029 1030 ch &= up->parity_mask; 1031 return ch; 1032 } 1033 1034 static void sunzilog_put_poll_char(struct uart_port *port, 1035 unsigned char ch) 1036 { 1037 struct uart_sunzilog_port *up = 1038 container_of(port, struct uart_sunzilog_port, port); 1039 1040 sunzilog_putchar(&up->port, ch); 1041 } 1042 #endif /* CONFIG_CONSOLE_POLL */ 1043 1044 static const struct uart_ops sunzilog_pops = { 1045 .tx_empty = sunzilog_tx_empty, 1046 .set_mctrl = sunzilog_set_mctrl, 1047 .get_mctrl = sunzilog_get_mctrl, 1048 .stop_tx = sunzilog_stop_tx, 1049 .start_tx = sunzilog_start_tx, 1050 .stop_rx = sunzilog_stop_rx, 1051 .enable_ms = sunzilog_enable_ms, 1052 .break_ctl = sunzilog_break_ctl, 1053 .startup = sunzilog_startup, 1054 .shutdown = sunzilog_shutdown, 1055 .set_termios = sunzilog_set_termios, 1056 .type = sunzilog_type, 1057 .release_port = sunzilog_release_port, 1058 .request_port = sunzilog_request_port, 1059 .config_port = sunzilog_config_port, 1060 .verify_port = sunzilog_verify_port, 1061 #ifdef CONFIG_CONSOLE_POLL 1062 .poll_get_char = sunzilog_get_poll_char, 1063 .poll_put_char = sunzilog_put_poll_char, 1064 #endif 1065 }; 1066 1067 static int uart_chip_count; 1068 static struct uart_sunzilog_port *sunzilog_port_table; 1069 static struct zilog_layout __iomem **sunzilog_chip_regs; 1070 1071 static struct uart_sunzilog_port *sunzilog_irq_chain; 1072 1073 static struct uart_driver sunzilog_reg = { 1074 .owner = THIS_MODULE, 1075 .driver_name = "sunzilog", 1076 .dev_name = "ttyS", 1077 .major = TTY_MAJOR, 1078 }; 1079 1080 static int __init sunzilog_alloc_tables(int num_sunzilog) 1081 { 1082 struct uart_sunzilog_port *up; 1083 unsigned long size; 1084 int num_channels = num_sunzilog * 2; 1085 int i; 1086 1087 size = num_channels * sizeof(struct uart_sunzilog_port); 1088 sunzilog_port_table = kzalloc(size, GFP_KERNEL); 1089 if (!sunzilog_port_table) 1090 return -ENOMEM; 1091 1092 for (i = 0; i < num_channels; i++) { 1093 up = &sunzilog_port_table[i]; 1094 1095 spin_lock_init(&up->port.lock); 1096 1097 if (i == 0) 1098 sunzilog_irq_chain = up; 1099 1100 if (i < num_channels - 1) 1101 up->next = up + 1; 1102 else 1103 up->next = NULL; 1104 } 1105 1106 size = num_sunzilog * sizeof(struct zilog_layout __iomem *); 1107 sunzilog_chip_regs = kzalloc(size, GFP_KERNEL); 1108 if (!sunzilog_chip_regs) { 1109 kfree(sunzilog_port_table); 1110 sunzilog_irq_chain = NULL; 1111 return -ENOMEM; 1112 } 1113 1114 return 0; 1115 } 1116 1117 static void sunzilog_free_tables(void) 1118 { 1119 kfree(sunzilog_port_table); 1120 sunzilog_irq_chain = NULL; 1121 kfree(sunzilog_chip_regs); 1122 } 1123 1124 #define ZS_PUT_CHAR_MAX_DELAY 2000 /* 10 ms */ 1125 1126 static void __maybe_unused sunzilog_putchar(struct uart_port *port, unsigned char ch) 1127 { 1128 struct zilog_channel __iomem *channel = ZILOG_CHANNEL_FROM_PORT(port); 1129 int loops = ZS_PUT_CHAR_MAX_DELAY; 1130 1131 /* This is a timed polling loop so do not switch the explicit 1132 * udelay with ZSDELAY as that is a NOP on some platforms. -DaveM 1133 */ 1134 do { 1135 unsigned char val = readb(&channel->control); 1136 if (val & Tx_BUF_EMP) { 1137 ZSDELAY(); 1138 break; 1139 } 1140 udelay(5); 1141 } while (--loops); 1142 1143 writeb(ch, &channel->data); 1144 ZSDELAY(); 1145 ZS_WSYNC(channel); 1146 } 1147 1148 #ifdef CONFIG_SERIO 1149 1150 static DEFINE_SPINLOCK(sunzilog_serio_lock); 1151 1152 static int sunzilog_serio_write(struct serio *serio, unsigned char ch) 1153 { 1154 struct uart_sunzilog_port *up = serio->port_data; 1155 unsigned long flags; 1156 1157 spin_lock_irqsave(&sunzilog_serio_lock, flags); 1158 1159 sunzilog_putchar(&up->port, ch); 1160 1161 spin_unlock_irqrestore(&sunzilog_serio_lock, flags); 1162 1163 return 0; 1164 } 1165 1166 static int sunzilog_serio_open(struct serio *serio) 1167 { 1168 struct uart_sunzilog_port *up = serio->port_data; 1169 unsigned long flags; 1170 int ret; 1171 1172 spin_lock_irqsave(&sunzilog_serio_lock, flags); 1173 if (!up->serio_open) { 1174 up->serio_open = 1; 1175 ret = 0; 1176 } else 1177 ret = -EBUSY; 1178 spin_unlock_irqrestore(&sunzilog_serio_lock, flags); 1179 1180 return ret; 1181 } 1182 1183 static void sunzilog_serio_close(struct serio *serio) 1184 { 1185 struct uart_sunzilog_port *up = serio->port_data; 1186 unsigned long flags; 1187 1188 spin_lock_irqsave(&sunzilog_serio_lock, flags); 1189 up->serio_open = 0; 1190 spin_unlock_irqrestore(&sunzilog_serio_lock, flags); 1191 } 1192 1193 #endif /* CONFIG_SERIO */ 1194 1195 #ifdef CONFIG_SERIAL_SUNZILOG_CONSOLE 1196 static void 1197 sunzilog_console_write(struct console *con, const char *s, unsigned int count) 1198 { 1199 struct uart_sunzilog_port *up = &sunzilog_port_table[con->index]; 1200 unsigned long flags; 1201 int locked = 1; 1202 1203 if (up->port.sysrq || oops_in_progress) 1204 locked = spin_trylock_irqsave(&up->port.lock, flags); 1205 else 1206 spin_lock_irqsave(&up->port.lock, flags); 1207 1208 uart_console_write(&up->port, s, count, sunzilog_putchar); 1209 udelay(2); 1210 1211 if (locked) 1212 spin_unlock_irqrestore(&up->port.lock, flags); 1213 } 1214 1215 static int __init sunzilog_console_setup(struct console *con, char *options) 1216 { 1217 struct uart_sunzilog_port *up = &sunzilog_port_table[con->index]; 1218 unsigned long flags; 1219 int baud, brg; 1220 1221 if (up->port.type != PORT_SUNZILOG) 1222 return -EINVAL; 1223 1224 printk(KERN_INFO "Console: ttyS%d (SunZilog zs%d)\n", 1225 (sunzilog_reg.minor - 64) + con->index, con->index); 1226 1227 /* Get firmware console settings. */ 1228 sunserial_console_termios(con, up->port.dev->of_node); 1229 1230 /* Firmware console speed is limited to 150-->38400 baud so 1231 * this hackish cflag thing is OK. 1232 */ 1233 switch (con->cflag & CBAUD) { 1234 case B150: baud = 150; break; 1235 case B300: baud = 300; break; 1236 case B600: baud = 600; break; 1237 case B1200: baud = 1200; break; 1238 case B2400: baud = 2400; break; 1239 case B4800: baud = 4800; break; 1240 default: case B9600: baud = 9600; break; 1241 case B19200: baud = 19200; break; 1242 case B38400: baud = 38400; break; 1243 } 1244 1245 brg = BPS_TO_BRG(baud, ZS_CLOCK / ZS_CLOCK_DIVISOR); 1246 1247 spin_lock_irqsave(&up->port.lock, flags); 1248 1249 up->curregs[R15] |= BRKIE; 1250 sunzilog_convert_to_zs(up, con->cflag, 0, brg); 1251 1252 sunzilog_set_mctrl(&up->port, TIOCM_DTR | TIOCM_RTS); 1253 __sunzilog_startup(up); 1254 1255 spin_unlock_irqrestore(&up->port.lock, flags); 1256 1257 return 0; 1258 } 1259 1260 static struct console sunzilog_console_ops = { 1261 .name = "ttyS", 1262 .write = sunzilog_console_write, 1263 .device = uart_console_device, 1264 .setup = sunzilog_console_setup, 1265 .flags = CON_PRINTBUFFER, 1266 .index = -1, 1267 .data = &sunzilog_reg, 1268 }; 1269 1270 static inline struct console *SUNZILOG_CONSOLE(void) 1271 { 1272 return &sunzilog_console_ops; 1273 } 1274 1275 #else 1276 #define SUNZILOG_CONSOLE() (NULL) 1277 #endif 1278 1279 static void sunzilog_init_kbdms(struct uart_sunzilog_port *up) 1280 { 1281 int baud, brg; 1282 1283 if (up->flags & SUNZILOG_FLAG_CONS_KEYB) { 1284 up->cflag = B1200 | CS8 | CLOCAL | CREAD; 1285 baud = 1200; 1286 } else { 1287 up->cflag = B4800 | CS8 | CLOCAL | CREAD; 1288 baud = 4800; 1289 } 1290 1291 up->curregs[R15] |= BRKIE; 1292 brg = BPS_TO_BRG(baud, ZS_CLOCK / ZS_CLOCK_DIVISOR); 1293 sunzilog_convert_to_zs(up, up->cflag, 0, brg); 1294 sunzilog_set_mctrl(&up->port, TIOCM_DTR | TIOCM_RTS); 1295 __sunzilog_startup(up); 1296 } 1297 1298 #ifdef CONFIG_SERIO 1299 static void sunzilog_register_serio(struct uart_sunzilog_port *up) 1300 { 1301 struct serio *serio = &up->serio; 1302 1303 serio->port_data = up; 1304 1305 serio->id.type = SERIO_RS232; 1306 if (up->flags & SUNZILOG_FLAG_CONS_KEYB) { 1307 serio->id.proto = SERIO_SUNKBD; 1308 strscpy(serio->name, "zskbd", sizeof(serio->name)); 1309 } else { 1310 serio->id.proto = SERIO_SUN; 1311 serio->id.extra = 1; 1312 strscpy(serio->name, "zsms", sizeof(serio->name)); 1313 } 1314 strscpy(serio->phys, 1315 ((up->flags & SUNZILOG_FLAG_CONS_KEYB) ? 1316 "zs/serio0" : "zs/serio1"), 1317 sizeof(serio->phys)); 1318 1319 serio->write = sunzilog_serio_write; 1320 serio->open = sunzilog_serio_open; 1321 serio->close = sunzilog_serio_close; 1322 serio->dev.parent = up->port.dev; 1323 1324 serio_register_port(serio); 1325 } 1326 #endif 1327 1328 static void sunzilog_init_hw(struct uart_sunzilog_port *up) 1329 { 1330 struct zilog_channel __iomem *channel; 1331 unsigned long flags; 1332 int baud, brg; 1333 1334 channel = ZILOG_CHANNEL_FROM_PORT(&up->port); 1335 1336 spin_lock_irqsave(&up->port.lock, flags); 1337 if (ZS_IS_CHANNEL_A(up)) { 1338 write_zsreg(channel, R9, FHWRES); 1339 ZSDELAY_LONG(); 1340 (void) read_zsreg(channel, R0); 1341 } 1342 1343 if (up->flags & (SUNZILOG_FLAG_CONS_KEYB | 1344 SUNZILOG_FLAG_CONS_MOUSE)) { 1345 up->curregs[R1] = EXT_INT_ENAB | INT_ALL_Rx | TxINT_ENAB; 1346 up->curregs[R4] = PAR_EVEN | X16CLK | SB1; 1347 up->curregs[R3] = RxENAB | Rx8; 1348 up->curregs[R5] = TxENAB | Tx8; 1349 up->curregs[R6] = 0x00; /* SDLC Address */ 1350 up->curregs[R7] = 0x7E; /* SDLC Flag */ 1351 up->curregs[R9] = NV; 1352 up->curregs[R7p] = 0x00; 1353 sunzilog_init_kbdms(up); 1354 /* Only enable interrupts if an ISR handler available */ 1355 if (up->flags & SUNZILOG_FLAG_ISR_HANDLER) 1356 up->curregs[R9] |= MIE; 1357 write_zsreg(channel, R9, up->curregs[R9]); 1358 } else { 1359 /* Normal serial TTY. */ 1360 up->parity_mask = 0xff; 1361 up->curregs[R1] = EXT_INT_ENAB | INT_ALL_Rx | TxINT_ENAB; 1362 up->curregs[R4] = PAR_EVEN | X16CLK | SB1; 1363 up->curregs[R3] = RxENAB | Rx8; 1364 up->curregs[R5] = TxENAB | Tx8; 1365 up->curregs[R6] = 0x00; /* SDLC Address */ 1366 up->curregs[R7] = 0x7E; /* SDLC Flag */ 1367 up->curregs[R9] = NV; 1368 up->curregs[R10] = NRZ; 1369 up->curregs[R11] = TCBR | RCBR; 1370 baud = 9600; 1371 brg = BPS_TO_BRG(baud, ZS_CLOCK / ZS_CLOCK_DIVISOR); 1372 up->curregs[R12] = (brg & 0xff); 1373 up->curregs[R13] = (brg >> 8) & 0xff; 1374 up->curregs[R14] = BRSRC | BRENAB; 1375 up->curregs[R15] = FIFOEN; /* Use FIFO if on ESCC */ 1376 up->curregs[R7p] = TxFIFO_LVL | RxFIFO_LVL; 1377 if (__load_zsregs(channel, up->curregs)) { 1378 up->flags |= SUNZILOG_FLAG_ESCC; 1379 } 1380 /* Only enable interrupts if an ISR handler available */ 1381 if (up->flags & SUNZILOG_FLAG_ISR_HANDLER) 1382 up->curregs[R9] |= MIE; 1383 write_zsreg(channel, R9, up->curregs[R9]); 1384 } 1385 1386 spin_unlock_irqrestore(&up->port.lock, flags); 1387 1388 #ifdef CONFIG_SERIO 1389 if (up->flags & (SUNZILOG_FLAG_CONS_KEYB | 1390 SUNZILOG_FLAG_CONS_MOUSE)) 1391 sunzilog_register_serio(up); 1392 #endif 1393 } 1394 1395 static int zilog_irq; 1396 1397 static int zs_probe(struct platform_device *op) 1398 { 1399 static int kbm_inst, uart_inst; 1400 int inst; 1401 struct uart_sunzilog_port *up; 1402 struct zilog_layout __iomem *rp; 1403 int keyboard_mouse = 0; 1404 int err; 1405 1406 if (of_property_present(op->dev.of_node, "keyboard")) 1407 keyboard_mouse = 1; 1408 1409 /* uarts must come before keyboards/mice */ 1410 if (keyboard_mouse) 1411 inst = uart_chip_count + kbm_inst; 1412 else 1413 inst = uart_inst; 1414 1415 sunzilog_chip_regs[inst] = of_ioremap(&op->resource[0], 0, 1416 sizeof(struct zilog_layout), 1417 "zs"); 1418 if (!sunzilog_chip_regs[inst]) 1419 return -ENOMEM; 1420 1421 rp = sunzilog_chip_regs[inst]; 1422 1423 if (!zilog_irq) 1424 zilog_irq = op->archdata.irqs[0]; 1425 1426 up = &sunzilog_port_table[inst * 2]; 1427 1428 /* Channel A */ 1429 up[0].port.mapbase = op->resource[0].start + 0x00; 1430 up[0].port.membase = (void __iomem *) &rp->channelA; 1431 up[0].port.iotype = UPIO_MEM; 1432 up[0].port.irq = op->archdata.irqs[0]; 1433 up[0].port.uartclk = ZS_CLOCK; 1434 up[0].port.fifosize = 1; 1435 up[0].port.ops = &sunzilog_pops; 1436 up[0].port.type = PORT_SUNZILOG; 1437 up[0].port.flags = 0; 1438 up[0].port.line = (inst * 2) + 0; 1439 up[0].port.dev = &op->dev; 1440 up[0].flags |= SUNZILOG_FLAG_IS_CHANNEL_A; 1441 up[0].port.has_sysrq = IS_ENABLED(CONFIG_SERIAL_SUNZILOG_CONSOLE); 1442 if (keyboard_mouse) 1443 up[0].flags |= SUNZILOG_FLAG_CONS_KEYB; 1444 sunzilog_init_hw(&up[0]); 1445 1446 /* Channel B */ 1447 up[1].port.mapbase = op->resource[0].start + 0x04; 1448 up[1].port.membase = (void __iomem *) &rp->channelB; 1449 up[1].port.iotype = UPIO_MEM; 1450 up[1].port.irq = op->archdata.irqs[0]; 1451 up[1].port.uartclk = ZS_CLOCK; 1452 up[1].port.fifosize = 1; 1453 up[1].port.ops = &sunzilog_pops; 1454 up[1].port.type = PORT_SUNZILOG; 1455 up[1].port.flags = 0; 1456 up[1].port.line = (inst * 2) + 1; 1457 up[1].port.dev = &op->dev; 1458 up[1].flags |= 0; 1459 up[1].port.has_sysrq = IS_ENABLED(CONFIG_SERIAL_SUNZILOG_CONSOLE); 1460 if (keyboard_mouse) 1461 up[1].flags |= SUNZILOG_FLAG_CONS_MOUSE; 1462 sunzilog_init_hw(&up[1]); 1463 1464 if (!keyboard_mouse) { 1465 if (sunserial_console_match(SUNZILOG_CONSOLE(), op->dev.of_node, 1466 &sunzilog_reg, up[0].port.line, 1467 false)) 1468 up->flags |= SUNZILOG_FLAG_IS_CONS; 1469 err = uart_add_one_port(&sunzilog_reg, &up[0].port); 1470 if (err) { 1471 of_iounmap(&op->resource[0], 1472 rp, sizeof(struct zilog_layout)); 1473 return err; 1474 } 1475 if (sunserial_console_match(SUNZILOG_CONSOLE(), op->dev.of_node, 1476 &sunzilog_reg, up[1].port.line, 1477 false)) 1478 up->flags |= SUNZILOG_FLAG_IS_CONS; 1479 err = uart_add_one_port(&sunzilog_reg, &up[1].port); 1480 if (err) { 1481 uart_remove_one_port(&sunzilog_reg, &up[0].port); 1482 of_iounmap(&op->resource[0], 1483 rp, sizeof(struct zilog_layout)); 1484 return err; 1485 } 1486 uart_inst++; 1487 } else { 1488 printk(KERN_INFO "%s: Keyboard at MMIO 0x%llx (irq = %d) " 1489 "is a %s\n", 1490 dev_name(&op->dev), 1491 (unsigned long long) up[0].port.mapbase, 1492 op->archdata.irqs[0], sunzilog_type(&up[0].port)); 1493 printk(KERN_INFO "%s: Mouse at MMIO 0x%llx (irq = %d) " 1494 "is a %s\n", 1495 dev_name(&op->dev), 1496 (unsigned long long) up[1].port.mapbase, 1497 op->archdata.irqs[0], sunzilog_type(&up[1].port)); 1498 kbm_inst++; 1499 } 1500 1501 platform_set_drvdata(op, &up[0]); 1502 1503 return 0; 1504 } 1505 1506 static void zs_remove_one(struct uart_sunzilog_port *up) 1507 { 1508 if (ZS_IS_KEYB(up) || ZS_IS_MOUSE(up)) { 1509 #ifdef CONFIG_SERIO 1510 serio_unregister_port(&up->serio); 1511 #endif 1512 } else 1513 uart_remove_one_port(&sunzilog_reg, &up->port); 1514 } 1515 1516 static int zs_remove(struct platform_device *op) 1517 { 1518 struct uart_sunzilog_port *up = platform_get_drvdata(op); 1519 struct zilog_layout __iomem *regs; 1520 1521 zs_remove_one(&up[0]); 1522 zs_remove_one(&up[1]); 1523 1524 regs = sunzilog_chip_regs[up[0].port.line / 2]; 1525 of_iounmap(&op->resource[0], regs, sizeof(struct zilog_layout)); 1526 1527 return 0; 1528 } 1529 1530 static const struct of_device_id zs_match[] = { 1531 { 1532 .name = "zs", 1533 }, 1534 {}, 1535 }; 1536 MODULE_DEVICE_TABLE(of, zs_match); 1537 1538 static struct platform_driver zs_driver = { 1539 .driver = { 1540 .name = "zs", 1541 .of_match_table = zs_match, 1542 }, 1543 .probe = zs_probe, 1544 .remove = zs_remove, 1545 }; 1546 1547 static int __init sunzilog_init(void) 1548 { 1549 struct device_node *dp; 1550 int err; 1551 int num_keybms = 0; 1552 int num_sunzilog = 0; 1553 1554 for_each_node_by_name(dp, "zs") { 1555 num_sunzilog++; 1556 if (of_property_present(dp, "keyboard")) 1557 num_keybms++; 1558 } 1559 1560 if (num_sunzilog) { 1561 err = sunzilog_alloc_tables(num_sunzilog); 1562 if (err) 1563 goto out; 1564 1565 uart_chip_count = num_sunzilog - num_keybms; 1566 1567 err = sunserial_register_minors(&sunzilog_reg, 1568 uart_chip_count * 2); 1569 if (err) 1570 goto out_free_tables; 1571 } 1572 1573 err = platform_driver_register(&zs_driver); 1574 if (err) 1575 goto out_unregister_uart; 1576 1577 if (zilog_irq) { 1578 struct uart_sunzilog_port *up = sunzilog_irq_chain; 1579 err = request_irq(zilog_irq, sunzilog_interrupt, IRQF_SHARED, 1580 "zs", sunzilog_irq_chain); 1581 if (err) 1582 goto out_unregister_driver; 1583 1584 /* Enable Interrupts */ 1585 while (up) { 1586 struct zilog_channel __iomem *channel; 1587 1588 /* printk (KERN_INFO "Enable IRQ for ZILOG Hardware %p\n", up); */ 1589 channel = ZILOG_CHANNEL_FROM_PORT(&up->port); 1590 up->flags |= SUNZILOG_FLAG_ISR_HANDLER; 1591 up->curregs[R9] |= MIE; 1592 write_zsreg(channel, R9, up->curregs[R9]); 1593 up = up->next; 1594 } 1595 } 1596 1597 out: 1598 return err; 1599 1600 out_unregister_driver: 1601 platform_driver_unregister(&zs_driver); 1602 1603 out_unregister_uart: 1604 if (num_sunzilog) { 1605 sunserial_unregister_minors(&sunzilog_reg, num_sunzilog); 1606 sunzilog_reg.cons = NULL; 1607 } 1608 1609 out_free_tables: 1610 sunzilog_free_tables(); 1611 goto out; 1612 } 1613 1614 static void __exit sunzilog_exit(void) 1615 { 1616 platform_driver_unregister(&zs_driver); 1617 1618 if (zilog_irq) { 1619 struct uart_sunzilog_port *up = sunzilog_irq_chain; 1620 1621 /* Disable Interrupts */ 1622 while (up) { 1623 struct zilog_channel __iomem *channel; 1624 1625 /* printk (KERN_INFO "Disable IRQ for ZILOG Hardware %p\n", up); */ 1626 channel = ZILOG_CHANNEL_FROM_PORT(&up->port); 1627 up->flags &= ~SUNZILOG_FLAG_ISR_HANDLER; 1628 up->curregs[R9] &= ~MIE; 1629 write_zsreg(channel, R9, up->curregs[R9]); 1630 up = up->next; 1631 } 1632 1633 free_irq(zilog_irq, sunzilog_irq_chain); 1634 zilog_irq = 0; 1635 } 1636 1637 if (sunzilog_reg.nr) { 1638 sunserial_unregister_minors(&sunzilog_reg, sunzilog_reg.nr); 1639 sunzilog_free_tables(); 1640 } 1641 } 1642 1643 module_init(sunzilog_init); 1644 module_exit(sunzilog_exit); 1645 1646 MODULE_AUTHOR("David S. Miller"); 1647 MODULE_DESCRIPTION("Sun Zilog serial port driver"); 1648 MODULE_VERSION("2.0"); 1649 MODULE_LICENSE("GPL"); 1650