1 // SPDX-License-Identifier: GPL-2.0 2 /* 3 * su.c: Small serial driver for keyboard/mouse interface on sparc32/PCI 4 * 5 * Copyright (C) 1997 Eddie C. Dost (ecd@skynet.be) 6 * Copyright (C) 1998-1999 Pete Zaitcev (zaitcev@yahoo.com) 7 * 8 * This is mainly a variation of 8250.c, credits go to authors mentioned 9 * therein. In fact this driver should be merged into the generic 8250.c 10 * infrastructure perhaps using a 8250_sparc.c module. 11 * 12 * Fixed to use tty_get_baud_rate(). 13 * Theodore Ts'o <tytso@mit.edu>, 2001-Oct-12 14 * 15 * Converted to new 2.5.x UART layer. 16 * David S. Miller (davem@davemloft.net), 2002-Jul-29 17 */ 18 19 #include <linux/module.h> 20 #include <linux/kernel.h> 21 #include <linux/spinlock.h> 22 #include <linux/errno.h> 23 #include <linux/tty.h> 24 #include <linux/tty_flip.h> 25 #include <linux/major.h> 26 #include <linux/string.h> 27 #include <linux/ptrace.h> 28 #include <linux/ioport.h> 29 #include <linux/circ_buf.h> 30 #include <linux/serial.h> 31 #include <linux/sysrq.h> 32 #include <linux/console.h> 33 #include <linux/slab.h> 34 #ifdef CONFIG_SERIO 35 #include <linux/serio.h> 36 #endif 37 #include <linux/serial_reg.h> 38 #include <linux/init.h> 39 #include <linux/delay.h> 40 #include <linux/of_device.h> 41 42 #include <asm/io.h> 43 #include <asm/irq.h> 44 #include <asm/prom.h> 45 #include <asm/setup.h> 46 47 #include <linux/serial_core.h> 48 #include <linux/sunserialcore.h> 49 50 /* We are on a NS PC87303 clocked with 24.0 MHz, which results 51 * in a UART clock of 1.8462 MHz. 52 */ 53 #define SU_BASE_BAUD (1846200 / 16) 54 55 enum su_type { SU_PORT_NONE, SU_PORT_MS, SU_PORT_KBD, SU_PORT_PORT }; 56 static char *su_typev[] = { "su(???)", "su(mouse)", "su(kbd)", "su(serial)" }; 57 58 struct serial_uart_config { 59 char *name; 60 int dfl_xmit_fifo_size; 61 int flags; 62 }; 63 64 /* 65 * Here we define the default xmit fifo size used for each type of UART. 66 */ 67 static const struct serial_uart_config uart_config[] = { 68 { "unknown", 1, 0 }, 69 { "8250", 1, 0 }, 70 { "16450", 1, 0 }, 71 { "16550", 1, 0 }, 72 { "16550A", 16, UART_CLEAR_FIFO | UART_USE_FIFO }, 73 { "Cirrus", 1, 0 }, 74 { "ST16650", 1, UART_CLEAR_FIFO | UART_STARTECH }, 75 { "ST16650V2", 32, UART_CLEAR_FIFO | UART_USE_FIFO | UART_STARTECH }, 76 { "TI16750", 64, UART_CLEAR_FIFO | UART_USE_FIFO }, 77 { "Startech", 1, 0 }, 78 { "16C950/954", 128, UART_CLEAR_FIFO | UART_USE_FIFO }, 79 { "ST16654", 64, UART_CLEAR_FIFO | UART_USE_FIFO | UART_STARTECH }, 80 { "XR16850", 128, UART_CLEAR_FIFO | UART_USE_FIFO | UART_STARTECH }, 81 { "RSA", 2048, UART_CLEAR_FIFO | UART_USE_FIFO } 82 }; 83 84 struct uart_sunsu_port { 85 struct uart_port port; 86 unsigned char acr; 87 unsigned char ier; 88 unsigned short rev; 89 unsigned char lcr; 90 unsigned int lsr_break_flag; 91 unsigned int cflag; 92 93 /* Probing information. */ 94 enum su_type su_type; 95 unsigned int type_probed; /* XXX Stupid */ 96 unsigned long reg_size; 97 98 #ifdef CONFIG_SERIO 99 struct serio serio; 100 int serio_open; 101 #endif 102 }; 103 104 static unsigned int serial_in(struct uart_sunsu_port *up, int offset) 105 { 106 offset <<= up->port.regshift; 107 108 switch (up->port.iotype) { 109 case UPIO_HUB6: 110 outb(up->port.hub6 - 1 + offset, up->port.iobase); 111 return inb(up->port.iobase + 1); 112 113 case UPIO_MEM: 114 return readb(up->port.membase + offset); 115 116 default: 117 return inb(up->port.iobase + offset); 118 } 119 } 120 121 static void serial_out(struct uart_sunsu_port *up, int offset, int value) 122 { 123 #ifndef CONFIG_SPARC64 124 /* 125 * MrCoffee has weird schematics: IRQ4 & P10(?) pins of SuperIO are 126 * connected with a gate then go to SlavIO. When IRQ4 goes tristated 127 * gate outputs a logical one. Since we use level triggered interrupts 128 * we have lockup and watchdog reset. We cannot mask IRQ because 129 * keyboard shares IRQ with us (Word has it as Bob Smelik's design). 130 * This problem is similar to what Alpha people suffer, see serial.c. 131 */ 132 if (offset == UART_MCR) 133 value |= UART_MCR_OUT2; 134 #endif 135 offset <<= up->port.regshift; 136 137 switch (up->port.iotype) { 138 case UPIO_HUB6: 139 outb(up->port.hub6 - 1 + offset, up->port.iobase); 140 outb(value, up->port.iobase + 1); 141 break; 142 143 case UPIO_MEM: 144 writeb(value, up->port.membase + offset); 145 break; 146 147 default: 148 outb(value, up->port.iobase + offset); 149 } 150 } 151 152 /* 153 * We used to support using pause I/O for certain machines. We 154 * haven't supported this for a while, but just in case it's badly 155 * needed for certain old 386 machines, I've left these #define's 156 * in.... 157 */ 158 #define serial_inp(up, offset) serial_in(up, offset) 159 #define serial_outp(up, offset, value) serial_out(up, offset, value) 160 161 162 /* 163 * For the 16C950 164 */ 165 static void serial_icr_write(struct uart_sunsu_port *up, int offset, int value) 166 { 167 serial_out(up, UART_SCR, offset); 168 serial_out(up, UART_ICR, value); 169 } 170 171 #if 0 /* Unused currently */ 172 static unsigned int serial_icr_read(struct uart_sunsu_port *up, int offset) 173 { 174 unsigned int value; 175 176 serial_icr_write(up, UART_ACR, up->acr | UART_ACR_ICRRD); 177 serial_out(up, UART_SCR, offset); 178 value = serial_in(up, UART_ICR); 179 serial_icr_write(up, UART_ACR, up->acr); 180 181 return value; 182 } 183 #endif 184 185 #ifdef CONFIG_SERIAL_8250_RSA 186 /* 187 * Attempts to turn on the RSA FIFO. Returns zero on failure. 188 * We set the port uart clock rate if we succeed. 189 */ 190 static int __enable_rsa(struct uart_sunsu_port *up) 191 { 192 unsigned char mode; 193 int result; 194 195 mode = serial_inp(up, UART_RSA_MSR); 196 result = mode & UART_RSA_MSR_FIFO; 197 198 if (!result) { 199 serial_outp(up, UART_RSA_MSR, mode | UART_RSA_MSR_FIFO); 200 mode = serial_inp(up, UART_RSA_MSR); 201 result = mode & UART_RSA_MSR_FIFO; 202 } 203 204 if (result) 205 up->port.uartclk = SERIAL_RSA_BAUD_BASE * 16; 206 207 return result; 208 } 209 210 static void enable_rsa(struct uart_sunsu_port *up) 211 { 212 if (up->port.type == PORT_RSA) { 213 if (up->port.uartclk != SERIAL_RSA_BAUD_BASE * 16) { 214 spin_lock_irq(&up->port.lock); 215 __enable_rsa(up); 216 spin_unlock_irq(&up->port.lock); 217 } 218 if (up->port.uartclk == SERIAL_RSA_BAUD_BASE * 16) 219 serial_outp(up, UART_RSA_FRR, 0); 220 } 221 } 222 223 /* 224 * Attempts to turn off the RSA FIFO. Returns zero on failure. 225 * It is unknown why interrupts were disabled in here. However, 226 * the caller is expected to preserve this behaviour by grabbing 227 * the spinlock before calling this function. 228 */ 229 static void disable_rsa(struct uart_sunsu_port *up) 230 { 231 unsigned char mode; 232 int result; 233 234 if (up->port.type == PORT_RSA && 235 up->port.uartclk == SERIAL_RSA_BAUD_BASE * 16) { 236 spin_lock_irq(&up->port.lock); 237 238 mode = serial_inp(up, UART_RSA_MSR); 239 result = !(mode & UART_RSA_MSR_FIFO); 240 241 if (!result) { 242 serial_outp(up, UART_RSA_MSR, mode & ~UART_RSA_MSR_FIFO); 243 mode = serial_inp(up, UART_RSA_MSR); 244 result = !(mode & UART_RSA_MSR_FIFO); 245 } 246 247 if (result) 248 up->port.uartclk = SERIAL_RSA_BAUD_BASE_LO * 16; 249 spin_unlock_irq(&up->port.lock); 250 } 251 } 252 #endif /* CONFIG_SERIAL_8250_RSA */ 253 254 static inline void __stop_tx(struct uart_sunsu_port *p) 255 { 256 if (p->ier & UART_IER_THRI) { 257 p->ier &= ~UART_IER_THRI; 258 serial_out(p, UART_IER, p->ier); 259 } 260 } 261 262 static void sunsu_stop_tx(struct uart_port *port) 263 { 264 struct uart_sunsu_port *up = 265 container_of(port, struct uart_sunsu_port, port); 266 267 __stop_tx(up); 268 269 /* 270 * We really want to stop the transmitter from sending. 271 */ 272 if (up->port.type == PORT_16C950) { 273 up->acr |= UART_ACR_TXDIS; 274 serial_icr_write(up, UART_ACR, up->acr); 275 } 276 } 277 278 static void sunsu_start_tx(struct uart_port *port) 279 { 280 struct uart_sunsu_port *up = 281 container_of(port, struct uart_sunsu_port, port); 282 283 if (!(up->ier & UART_IER_THRI)) { 284 up->ier |= UART_IER_THRI; 285 serial_out(up, UART_IER, up->ier); 286 } 287 288 /* 289 * Re-enable the transmitter if we disabled it. 290 */ 291 if (up->port.type == PORT_16C950 && up->acr & UART_ACR_TXDIS) { 292 up->acr &= ~UART_ACR_TXDIS; 293 serial_icr_write(up, UART_ACR, up->acr); 294 } 295 } 296 297 static void sunsu_stop_rx(struct uart_port *port) 298 { 299 struct uart_sunsu_port *up = 300 container_of(port, struct uart_sunsu_port, port); 301 302 up->ier &= ~UART_IER_RLSI; 303 up->port.read_status_mask &= ~UART_LSR_DR; 304 serial_out(up, UART_IER, up->ier); 305 } 306 307 static void sunsu_enable_ms(struct uart_port *port) 308 { 309 struct uart_sunsu_port *up = 310 container_of(port, struct uart_sunsu_port, port); 311 unsigned long flags; 312 313 spin_lock_irqsave(&up->port.lock, flags); 314 up->ier |= UART_IER_MSI; 315 serial_out(up, UART_IER, up->ier); 316 spin_unlock_irqrestore(&up->port.lock, flags); 317 } 318 319 static void 320 receive_chars(struct uart_sunsu_port *up, unsigned char *status) 321 { 322 struct tty_port *port = &up->port.state->port; 323 unsigned char ch, flag; 324 int max_count = 256; 325 int saw_console_brk = 0; 326 327 do { 328 ch = serial_inp(up, UART_RX); 329 flag = TTY_NORMAL; 330 up->port.icount.rx++; 331 332 if (unlikely(*status & (UART_LSR_BI | UART_LSR_PE | 333 UART_LSR_FE | UART_LSR_OE))) { 334 /* 335 * For statistics only 336 */ 337 if (*status & UART_LSR_BI) { 338 *status &= ~(UART_LSR_FE | UART_LSR_PE); 339 up->port.icount.brk++; 340 if (up->port.cons != NULL && 341 up->port.line == up->port.cons->index) 342 saw_console_brk = 1; 343 /* 344 * We do the SysRQ and SAK checking 345 * here because otherwise the break 346 * may get masked by ignore_status_mask 347 * or read_status_mask. 348 */ 349 if (uart_handle_break(&up->port)) 350 goto ignore_char; 351 } else if (*status & UART_LSR_PE) 352 up->port.icount.parity++; 353 else if (*status & UART_LSR_FE) 354 up->port.icount.frame++; 355 if (*status & UART_LSR_OE) 356 up->port.icount.overrun++; 357 358 /* 359 * Mask off conditions which should be ingored. 360 */ 361 *status &= up->port.read_status_mask; 362 363 if (up->port.cons != NULL && 364 up->port.line == up->port.cons->index) { 365 /* Recover the break flag from console xmit */ 366 *status |= up->lsr_break_flag; 367 up->lsr_break_flag = 0; 368 } 369 370 if (*status & UART_LSR_BI) { 371 flag = TTY_BREAK; 372 } else if (*status & UART_LSR_PE) 373 flag = TTY_PARITY; 374 else if (*status & UART_LSR_FE) 375 flag = TTY_FRAME; 376 } 377 if (uart_handle_sysrq_char(&up->port, ch)) 378 goto ignore_char; 379 if ((*status & up->port.ignore_status_mask) == 0) 380 tty_insert_flip_char(port, ch, flag); 381 if (*status & UART_LSR_OE) 382 /* 383 * Overrun is special, since it's reported 384 * immediately, and doesn't affect the current 385 * character. 386 */ 387 tty_insert_flip_char(port, 0, TTY_OVERRUN); 388 ignore_char: 389 *status = serial_inp(up, UART_LSR); 390 } while ((*status & UART_LSR_DR) && (max_count-- > 0)); 391 392 if (saw_console_brk) 393 sun_do_break(); 394 } 395 396 static void transmit_chars(struct uart_sunsu_port *up) 397 { 398 struct circ_buf *xmit = &up->port.state->xmit; 399 int count; 400 401 if (up->port.x_char) { 402 serial_outp(up, UART_TX, up->port.x_char); 403 up->port.icount.tx++; 404 up->port.x_char = 0; 405 return; 406 } 407 if (uart_tx_stopped(&up->port)) { 408 sunsu_stop_tx(&up->port); 409 return; 410 } 411 if (uart_circ_empty(xmit)) { 412 __stop_tx(up); 413 return; 414 } 415 416 count = up->port.fifosize; 417 do { 418 serial_out(up, UART_TX, xmit->buf[xmit->tail]); 419 xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1); 420 up->port.icount.tx++; 421 if (uart_circ_empty(xmit)) 422 break; 423 } while (--count > 0); 424 425 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) 426 uart_write_wakeup(&up->port); 427 428 if (uart_circ_empty(xmit)) 429 __stop_tx(up); 430 } 431 432 static void check_modem_status(struct uart_sunsu_port *up) 433 { 434 int status; 435 436 status = serial_in(up, UART_MSR); 437 438 if ((status & UART_MSR_ANY_DELTA) == 0) 439 return; 440 441 if (status & UART_MSR_TERI) 442 up->port.icount.rng++; 443 if (status & UART_MSR_DDSR) 444 up->port.icount.dsr++; 445 if (status & UART_MSR_DDCD) 446 uart_handle_dcd_change(&up->port, status & UART_MSR_DCD); 447 if (status & UART_MSR_DCTS) 448 uart_handle_cts_change(&up->port, status & UART_MSR_CTS); 449 450 wake_up_interruptible(&up->port.state->port.delta_msr_wait); 451 } 452 453 static irqreturn_t sunsu_serial_interrupt(int irq, void *dev_id) 454 { 455 struct uart_sunsu_port *up = dev_id; 456 unsigned long flags; 457 unsigned char status; 458 459 spin_lock_irqsave(&up->port.lock, flags); 460 461 do { 462 status = serial_inp(up, UART_LSR); 463 if (status & UART_LSR_DR) 464 receive_chars(up, &status); 465 check_modem_status(up); 466 if (status & UART_LSR_THRE) 467 transmit_chars(up); 468 469 spin_unlock_irqrestore(&up->port.lock, flags); 470 471 tty_flip_buffer_push(&up->port.state->port); 472 473 spin_lock_irqsave(&up->port.lock, flags); 474 475 } while (!(serial_in(up, UART_IIR) & UART_IIR_NO_INT)); 476 477 spin_unlock_irqrestore(&up->port.lock, flags); 478 479 return IRQ_HANDLED; 480 } 481 482 /* Separate interrupt handling path for keyboard/mouse ports. */ 483 484 static void 485 sunsu_change_speed(struct uart_port *port, unsigned int cflag, 486 unsigned int iflag, unsigned int quot); 487 488 static void sunsu_change_mouse_baud(struct uart_sunsu_port *up) 489 { 490 unsigned int cur_cflag = up->cflag; 491 int quot, new_baud; 492 493 up->cflag &= ~CBAUD; 494 up->cflag |= suncore_mouse_baud_cflag_next(cur_cflag, &new_baud); 495 496 quot = up->port.uartclk / (16 * new_baud); 497 498 sunsu_change_speed(&up->port, up->cflag, 0, quot); 499 } 500 501 static void receive_kbd_ms_chars(struct uart_sunsu_port *up, int is_break) 502 { 503 do { 504 unsigned char ch = serial_inp(up, UART_RX); 505 506 /* Stop-A is handled by drivers/char/keyboard.c now. */ 507 if (up->su_type == SU_PORT_KBD) { 508 #ifdef CONFIG_SERIO 509 serio_interrupt(&up->serio, ch, 0); 510 #endif 511 } else if (up->su_type == SU_PORT_MS) { 512 int ret = suncore_mouse_baud_detection(ch, is_break); 513 514 switch (ret) { 515 case 2: 516 sunsu_change_mouse_baud(up); 517 /* fallthru */ 518 case 1: 519 break; 520 521 case 0: 522 #ifdef CONFIG_SERIO 523 serio_interrupt(&up->serio, ch, 0); 524 #endif 525 break; 526 } 527 } 528 } while (serial_in(up, UART_LSR) & UART_LSR_DR); 529 } 530 531 static irqreturn_t sunsu_kbd_ms_interrupt(int irq, void *dev_id) 532 { 533 struct uart_sunsu_port *up = dev_id; 534 535 if (!(serial_in(up, UART_IIR) & UART_IIR_NO_INT)) { 536 unsigned char status = serial_inp(up, UART_LSR); 537 538 if ((status & UART_LSR_DR) || (status & UART_LSR_BI)) 539 receive_kbd_ms_chars(up, (status & UART_LSR_BI) != 0); 540 } 541 542 return IRQ_HANDLED; 543 } 544 545 static unsigned int sunsu_tx_empty(struct uart_port *port) 546 { 547 struct uart_sunsu_port *up = 548 container_of(port, struct uart_sunsu_port, port); 549 unsigned long flags; 550 unsigned int ret; 551 552 spin_lock_irqsave(&up->port.lock, flags); 553 ret = serial_in(up, UART_LSR) & UART_LSR_TEMT ? TIOCSER_TEMT : 0; 554 spin_unlock_irqrestore(&up->port.lock, flags); 555 556 return ret; 557 } 558 559 static unsigned int sunsu_get_mctrl(struct uart_port *port) 560 { 561 struct uart_sunsu_port *up = 562 container_of(port, struct uart_sunsu_port, port); 563 unsigned char status; 564 unsigned int ret; 565 566 status = serial_in(up, UART_MSR); 567 568 ret = 0; 569 if (status & UART_MSR_DCD) 570 ret |= TIOCM_CAR; 571 if (status & UART_MSR_RI) 572 ret |= TIOCM_RNG; 573 if (status & UART_MSR_DSR) 574 ret |= TIOCM_DSR; 575 if (status & UART_MSR_CTS) 576 ret |= TIOCM_CTS; 577 return ret; 578 } 579 580 static void sunsu_set_mctrl(struct uart_port *port, unsigned int mctrl) 581 { 582 struct uart_sunsu_port *up = 583 container_of(port, struct uart_sunsu_port, port); 584 unsigned char mcr = 0; 585 586 if (mctrl & TIOCM_RTS) 587 mcr |= UART_MCR_RTS; 588 if (mctrl & TIOCM_DTR) 589 mcr |= UART_MCR_DTR; 590 if (mctrl & TIOCM_OUT1) 591 mcr |= UART_MCR_OUT1; 592 if (mctrl & TIOCM_OUT2) 593 mcr |= UART_MCR_OUT2; 594 if (mctrl & TIOCM_LOOP) 595 mcr |= UART_MCR_LOOP; 596 597 serial_out(up, UART_MCR, mcr); 598 } 599 600 static void sunsu_break_ctl(struct uart_port *port, int break_state) 601 { 602 struct uart_sunsu_port *up = 603 container_of(port, struct uart_sunsu_port, port); 604 unsigned long flags; 605 606 spin_lock_irqsave(&up->port.lock, flags); 607 if (break_state == -1) 608 up->lcr |= UART_LCR_SBC; 609 else 610 up->lcr &= ~UART_LCR_SBC; 611 serial_out(up, UART_LCR, up->lcr); 612 spin_unlock_irqrestore(&up->port.lock, flags); 613 } 614 615 static int sunsu_startup(struct uart_port *port) 616 { 617 struct uart_sunsu_port *up = 618 container_of(port, struct uart_sunsu_port, port); 619 unsigned long flags; 620 int retval; 621 622 if (up->port.type == PORT_16C950) { 623 /* Wake up and initialize UART */ 624 up->acr = 0; 625 serial_outp(up, UART_LCR, 0xBF); 626 serial_outp(up, UART_EFR, UART_EFR_ECB); 627 serial_outp(up, UART_IER, 0); 628 serial_outp(up, UART_LCR, 0); 629 serial_icr_write(up, UART_CSR, 0); /* Reset the UART */ 630 serial_outp(up, UART_LCR, 0xBF); 631 serial_outp(up, UART_EFR, UART_EFR_ECB); 632 serial_outp(up, UART_LCR, 0); 633 } 634 635 #ifdef CONFIG_SERIAL_8250_RSA 636 /* 637 * If this is an RSA port, see if we can kick it up to the 638 * higher speed clock. 639 */ 640 enable_rsa(up); 641 #endif 642 643 /* 644 * Clear the FIFO buffers and disable them. 645 * (they will be reenabled in set_termios()) 646 */ 647 if (uart_config[up->port.type].flags & UART_CLEAR_FIFO) { 648 serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO); 649 serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO | 650 UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT); 651 serial_outp(up, UART_FCR, 0); 652 } 653 654 /* 655 * Clear the interrupt registers. 656 */ 657 (void) serial_inp(up, UART_LSR); 658 (void) serial_inp(up, UART_RX); 659 (void) serial_inp(up, UART_IIR); 660 (void) serial_inp(up, UART_MSR); 661 662 /* 663 * At this point, there's no way the LSR could still be 0xff; 664 * if it is, then bail out, because there's likely no UART 665 * here. 666 */ 667 if (!(up->port.flags & UPF_BUGGY_UART) && 668 (serial_inp(up, UART_LSR) == 0xff)) { 669 printk("ttyS%d: LSR safety check engaged!\n", up->port.line); 670 return -ENODEV; 671 } 672 673 if (up->su_type != SU_PORT_PORT) { 674 retval = request_irq(up->port.irq, sunsu_kbd_ms_interrupt, 675 IRQF_SHARED, su_typev[up->su_type], up); 676 } else { 677 retval = request_irq(up->port.irq, sunsu_serial_interrupt, 678 IRQF_SHARED, su_typev[up->su_type], up); 679 } 680 if (retval) { 681 printk("su: Cannot register IRQ %d\n", up->port.irq); 682 return retval; 683 } 684 685 /* 686 * Now, initialize the UART 687 */ 688 serial_outp(up, UART_LCR, UART_LCR_WLEN8); 689 690 spin_lock_irqsave(&up->port.lock, flags); 691 692 up->port.mctrl |= TIOCM_OUT2; 693 694 sunsu_set_mctrl(&up->port, up->port.mctrl); 695 spin_unlock_irqrestore(&up->port.lock, flags); 696 697 /* 698 * Finally, enable interrupts. Note: Modem status interrupts 699 * are set via set_termios(), which will be occurring imminently 700 * anyway, so we don't enable them here. 701 */ 702 up->ier = UART_IER_RLSI | UART_IER_RDI; 703 serial_outp(up, UART_IER, up->ier); 704 705 if (up->port.flags & UPF_FOURPORT) { 706 unsigned int icp; 707 /* 708 * Enable interrupts on the AST Fourport board 709 */ 710 icp = (up->port.iobase & 0xfe0) | 0x01f; 711 outb_p(0x80, icp); 712 (void) inb_p(icp); 713 } 714 715 /* 716 * And clear the interrupt registers again for luck. 717 */ 718 (void) serial_inp(up, UART_LSR); 719 (void) serial_inp(up, UART_RX); 720 (void) serial_inp(up, UART_IIR); 721 (void) serial_inp(up, UART_MSR); 722 723 return 0; 724 } 725 726 static void sunsu_shutdown(struct uart_port *port) 727 { 728 struct uart_sunsu_port *up = 729 container_of(port, struct uart_sunsu_port, port); 730 unsigned long flags; 731 732 /* 733 * Disable interrupts from this port 734 */ 735 up->ier = 0; 736 serial_outp(up, UART_IER, 0); 737 738 spin_lock_irqsave(&up->port.lock, flags); 739 if (up->port.flags & UPF_FOURPORT) { 740 /* reset interrupts on the AST Fourport board */ 741 inb((up->port.iobase & 0xfe0) | 0x1f); 742 up->port.mctrl |= TIOCM_OUT1; 743 } else 744 up->port.mctrl &= ~TIOCM_OUT2; 745 746 sunsu_set_mctrl(&up->port, up->port.mctrl); 747 spin_unlock_irqrestore(&up->port.lock, flags); 748 749 /* 750 * Disable break condition and FIFOs 751 */ 752 serial_out(up, UART_LCR, serial_inp(up, UART_LCR) & ~UART_LCR_SBC); 753 serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO | 754 UART_FCR_CLEAR_RCVR | 755 UART_FCR_CLEAR_XMIT); 756 serial_outp(up, UART_FCR, 0); 757 758 #ifdef CONFIG_SERIAL_8250_RSA 759 /* 760 * Reset the RSA board back to 115kbps compat mode. 761 */ 762 disable_rsa(up); 763 #endif 764 765 /* 766 * Read data port to reset things. 767 */ 768 (void) serial_in(up, UART_RX); 769 770 free_irq(up->port.irq, up); 771 } 772 773 static void 774 sunsu_change_speed(struct uart_port *port, unsigned int cflag, 775 unsigned int iflag, unsigned int quot) 776 { 777 struct uart_sunsu_port *up = 778 container_of(port, struct uart_sunsu_port, port); 779 unsigned char cval, fcr = 0; 780 unsigned long flags; 781 782 switch (cflag & CSIZE) { 783 case CS5: 784 cval = 0x00; 785 break; 786 case CS6: 787 cval = 0x01; 788 break; 789 case CS7: 790 cval = 0x02; 791 break; 792 default: 793 case CS8: 794 cval = 0x03; 795 break; 796 } 797 798 if (cflag & CSTOPB) 799 cval |= 0x04; 800 if (cflag & PARENB) 801 cval |= UART_LCR_PARITY; 802 if (!(cflag & PARODD)) 803 cval |= UART_LCR_EPAR; 804 #ifdef CMSPAR 805 if (cflag & CMSPAR) 806 cval |= UART_LCR_SPAR; 807 #endif 808 809 /* 810 * Work around a bug in the Oxford Semiconductor 952 rev B 811 * chip which causes it to seriously miscalculate baud rates 812 * when DLL is 0. 813 */ 814 if ((quot & 0xff) == 0 && up->port.type == PORT_16C950 && 815 up->rev == 0x5201) 816 quot ++; 817 818 if (uart_config[up->port.type].flags & UART_USE_FIFO) { 819 if ((up->port.uartclk / quot) < (2400 * 16)) 820 fcr = UART_FCR_ENABLE_FIFO | UART_FCR_TRIGGER_1; 821 #ifdef CONFIG_SERIAL_8250_RSA 822 else if (up->port.type == PORT_RSA) 823 fcr = UART_FCR_ENABLE_FIFO | UART_FCR_TRIGGER_14; 824 #endif 825 else 826 fcr = UART_FCR_ENABLE_FIFO | UART_FCR_TRIGGER_8; 827 } 828 if (up->port.type == PORT_16750) 829 fcr |= UART_FCR7_64BYTE; 830 831 /* 832 * Ok, we're now changing the port state. Do it with 833 * interrupts disabled. 834 */ 835 spin_lock_irqsave(&up->port.lock, flags); 836 837 /* 838 * Update the per-port timeout. 839 */ 840 uart_update_timeout(port, cflag, (port->uartclk / (16 * quot))); 841 842 up->port.read_status_mask = UART_LSR_OE | UART_LSR_THRE | UART_LSR_DR; 843 if (iflag & INPCK) 844 up->port.read_status_mask |= UART_LSR_FE | UART_LSR_PE; 845 if (iflag & (IGNBRK | BRKINT | PARMRK)) 846 up->port.read_status_mask |= UART_LSR_BI; 847 848 /* 849 * Characteres to ignore 850 */ 851 up->port.ignore_status_mask = 0; 852 if (iflag & IGNPAR) 853 up->port.ignore_status_mask |= UART_LSR_PE | UART_LSR_FE; 854 if (iflag & IGNBRK) { 855 up->port.ignore_status_mask |= UART_LSR_BI; 856 /* 857 * If we're ignoring parity and break indicators, 858 * ignore overruns too (for real raw support). 859 */ 860 if (iflag & IGNPAR) 861 up->port.ignore_status_mask |= UART_LSR_OE; 862 } 863 864 /* 865 * ignore all characters if CREAD is not set 866 */ 867 if ((cflag & CREAD) == 0) 868 up->port.ignore_status_mask |= UART_LSR_DR; 869 870 /* 871 * CTS flow control flag and modem status interrupts 872 */ 873 up->ier &= ~UART_IER_MSI; 874 if (UART_ENABLE_MS(&up->port, cflag)) 875 up->ier |= UART_IER_MSI; 876 877 serial_out(up, UART_IER, up->ier); 878 879 if (uart_config[up->port.type].flags & UART_STARTECH) { 880 serial_outp(up, UART_LCR, 0xBF); 881 serial_outp(up, UART_EFR, cflag & CRTSCTS ? UART_EFR_CTS :0); 882 } 883 serial_outp(up, UART_LCR, cval | UART_LCR_DLAB);/* set DLAB */ 884 serial_outp(up, UART_DLL, quot & 0xff); /* LS of divisor */ 885 serial_outp(up, UART_DLM, quot >> 8); /* MS of divisor */ 886 if (up->port.type == PORT_16750) 887 serial_outp(up, UART_FCR, fcr); /* set fcr */ 888 serial_outp(up, UART_LCR, cval); /* reset DLAB */ 889 up->lcr = cval; /* Save LCR */ 890 if (up->port.type != PORT_16750) { 891 if (fcr & UART_FCR_ENABLE_FIFO) { 892 /* emulated UARTs (Lucent Venus 167x) need two steps */ 893 serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO); 894 } 895 serial_outp(up, UART_FCR, fcr); /* set fcr */ 896 } 897 898 up->cflag = cflag; 899 900 spin_unlock_irqrestore(&up->port.lock, flags); 901 } 902 903 static void 904 sunsu_set_termios(struct uart_port *port, struct ktermios *termios, 905 struct ktermios *old) 906 { 907 unsigned int baud, quot; 908 909 /* 910 * Ask the core to calculate the divisor for us. 911 */ 912 baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16); 913 quot = uart_get_divisor(port, baud); 914 915 sunsu_change_speed(port, termios->c_cflag, termios->c_iflag, quot); 916 } 917 918 static void sunsu_release_port(struct uart_port *port) 919 { 920 } 921 922 static int sunsu_request_port(struct uart_port *port) 923 { 924 return 0; 925 } 926 927 static void sunsu_config_port(struct uart_port *port, int flags) 928 { 929 struct uart_sunsu_port *up = 930 container_of(port, struct uart_sunsu_port, port); 931 932 if (flags & UART_CONFIG_TYPE) { 933 /* 934 * We are supposed to call autoconfig here, but this requires 935 * splitting all the OBP probing crap from the UART probing. 936 * We'll do it when we kill sunsu.c altogether. 937 */ 938 port->type = up->type_probed; /* XXX */ 939 } 940 } 941 942 static int 943 sunsu_verify_port(struct uart_port *port, struct serial_struct *ser) 944 { 945 return -EINVAL; 946 } 947 948 static const char * 949 sunsu_type(struct uart_port *port) 950 { 951 int type = port->type; 952 953 if (type >= ARRAY_SIZE(uart_config)) 954 type = 0; 955 return uart_config[type].name; 956 } 957 958 static const struct uart_ops sunsu_pops = { 959 .tx_empty = sunsu_tx_empty, 960 .set_mctrl = sunsu_set_mctrl, 961 .get_mctrl = sunsu_get_mctrl, 962 .stop_tx = sunsu_stop_tx, 963 .start_tx = sunsu_start_tx, 964 .stop_rx = sunsu_stop_rx, 965 .enable_ms = sunsu_enable_ms, 966 .break_ctl = sunsu_break_ctl, 967 .startup = sunsu_startup, 968 .shutdown = sunsu_shutdown, 969 .set_termios = sunsu_set_termios, 970 .type = sunsu_type, 971 .release_port = sunsu_release_port, 972 .request_port = sunsu_request_port, 973 .config_port = sunsu_config_port, 974 .verify_port = sunsu_verify_port, 975 }; 976 977 #define UART_NR 4 978 979 static struct uart_sunsu_port sunsu_ports[UART_NR]; 980 static int nr_inst; /* Number of already registered ports */ 981 982 #ifdef CONFIG_SERIO 983 984 static DEFINE_SPINLOCK(sunsu_serio_lock); 985 986 static int sunsu_serio_write(struct serio *serio, unsigned char ch) 987 { 988 struct uart_sunsu_port *up = serio->port_data; 989 unsigned long flags; 990 int lsr; 991 992 spin_lock_irqsave(&sunsu_serio_lock, flags); 993 994 do { 995 lsr = serial_in(up, UART_LSR); 996 } while (!(lsr & UART_LSR_THRE)); 997 998 /* Send the character out. */ 999 serial_out(up, UART_TX, ch); 1000 1001 spin_unlock_irqrestore(&sunsu_serio_lock, flags); 1002 1003 return 0; 1004 } 1005 1006 static int sunsu_serio_open(struct serio *serio) 1007 { 1008 struct uart_sunsu_port *up = serio->port_data; 1009 unsigned long flags; 1010 int ret; 1011 1012 spin_lock_irqsave(&sunsu_serio_lock, flags); 1013 if (!up->serio_open) { 1014 up->serio_open = 1; 1015 ret = 0; 1016 } else 1017 ret = -EBUSY; 1018 spin_unlock_irqrestore(&sunsu_serio_lock, flags); 1019 1020 return ret; 1021 } 1022 1023 static void sunsu_serio_close(struct serio *serio) 1024 { 1025 struct uart_sunsu_port *up = serio->port_data; 1026 unsigned long flags; 1027 1028 spin_lock_irqsave(&sunsu_serio_lock, flags); 1029 up->serio_open = 0; 1030 spin_unlock_irqrestore(&sunsu_serio_lock, flags); 1031 } 1032 1033 #endif /* CONFIG_SERIO */ 1034 1035 static void sunsu_autoconfig(struct uart_sunsu_port *up) 1036 { 1037 unsigned char status1, status2, scratch, scratch2, scratch3; 1038 unsigned char save_lcr, save_mcr; 1039 unsigned long flags; 1040 1041 if (up->su_type == SU_PORT_NONE) 1042 return; 1043 1044 up->type_probed = PORT_UNKNOWN; 1045 up->port.iotype = UPIO_MEM; 1046 1047 spin_lock_irqsave(&up->port.lock, flags); 1048 1049 if (!(up->port.flags & UPF_BUGGY_UART)) { 1050 /* 1051 * Do a simple existence test first; if we fail this, there's 1052 * no point trying anything else. 1053 * 1054 * 0x80 is used as a nonsense port to prevent against false 1055 * positives due to ISA bus float. The assumption is that 1056 * 0x80 is a non-existent port; which should be safe since 1057 * include/asm/io.h also makes this assumption. 1058 */ 1059 scratch = serial_inp(up, UART_IER); 1060 serial_outp(up, UART_IER, 0); 1061 #ifdef __i386__ 1062 outb(0xff, 0x080); 1063 #endif 1064 scratch2 = serial_inp(up, UART_IER); 1065 serial_outp(up, UART_IER, 0x0f); 1066 #ifdef __i386__ 1067 outb(0, 0x080); 1068 #endif 1069 scratch3 = serial_inp(up, UART_IER); 1070 serial_outp(up, UART_IER, scratch); 1071 if (scratch2 != 0 || scratch3 != 0x0F) 1072 goto out; /* We failed; there's nothing here */ 1073 } 1074 1075 save_mcr = serial_in(up, UART_MCR); 1076 save_lcr = serial_in(up, UART_LCR); 1077 1078 /* 1079 * Check to see if a UART is really there. Certain broken 1080 * internal modems based on the Rockwell chipset fail this 1081 * test, because they apparently don't implement the loopback 1082 * test mode. So this test is skipped on the COM 1 through 1083 * COM 4 ports. This *should* be safe, since no board 1084 * manufacturer would be stupid enough to design a board 1085 * that conflicts with COM 1-4 --- we hope! 1086 */ 1087 if (!(up->port.flags & UPF_SKIP_TEST)) { 1088 serial_outp(up, UART_MCR, UART_MCR_LOOP | 0x0A); 1089 status1 = serial_inp(up, UART_MSR) & 0xF0; 1090 serial_outp(up, UART_MCR, save_mcr); 1091 if (status1 != 0x90) 1092 goto out; /* We failed loopback test */ 1093 } 1094 serial_outp(up, UART_LCR, 0xBF); /* set up for StarTech test */ 1095 serial_outp(up, UART_EFR, 0); /* EFR is the same as FCR */ 1096 serial_outp(up, UART_LCR, 0); 1097 serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO); 1098 scratch = serial_in(up, UART_IIR) >> 6; 1099 switch (scratch) { 1100 case 0: 1101 up->port.type = PORT_16450; 1102 break; 1103 case 1: 1104 up->port.type = PORT_UNKNOWN; 1105 break; 1106 case 2: 1107 up->port.type = PORT_16550; 1108 break; 1109 case 3: 1110 up->port.type = PORT_16550A; 1111 break; 1112 } 1113 if (up->port.type == PORT_16550A) { 1114 /* Check for Startech UART's */ 1115 serial_outp(up, UART_LCR, UART_LCR_DLAB); 1116 if (serial_in(up, UART_EFR) == 0) { 1117 up->port.type = PORT_16650; 1118 } else { 1119 serial_outp(up, UART_LCR, 0xBF); 1120 if (serial_in(up, UART_EFR) == 0) 1121 up->port.type = PORT_16650V2; 1122 } 1123 } 1124 if (up->port.type == PORT_16550A) { 1125 /* Check for TI 16750 */ 1126 serial_outp(up, UART_LCR, save_lcr | UART_LCR_DLAB); 1127 serial_outp(up, UART_FCR, 1128 UART_FCR_ENABLE_FIFO | UART_FCR7_64BYTE); 1129 scratch = serial_in(up, UART_IIR) >> 5; 1130 if (scratch == 7) { 1131 /* 1132 * If this is a 16750, and not a cheap UART 1133 * clone, then it should only go into 64 byte 1134 * mode if the UART_FCR7_64BYTE bit was set 1135 * while UART_LCR_DLAB was latched. 1136 */ 1137 serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO); 1138 serial_outp(up, UART_LCR, 0); 1139 serial_outp(up, UART_FCR, 1140 UART_FCR_ENABLE_FIFO | UART_FCR7_64BYTE); 1141 scratch = serial_in(up, UART_IIR) >> 5; 1142 if (scratch == 6) 1143 up->port.type = PORT_16750; 1144 } 1145 serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO); 1146 } 1147 serial_outp(up, UART_LCR, save_lcr); 1148 if (up->port.type == PORT_16450) { 1149 scratch = serial_in(up, UART_SCR); 1150 serial_outp(up, UART_SCR, 0xa5); 1151 status1 = serial_in(up, UART_SCR); 1152 serial_outp(up, UART_SCR, 0x5a); 1153 status2 = serial_in(up, UART_SCR); 1154 serial_outp(up, UART_SCR, scratch); 1155 1156 if ((status1 != 0xa5) || (status2 != 0x5a)) 1157 up->port.type = PORT_8250; 1158 } 1159 1160 up->port.fifosize = uart_config[up->port.type].dfl_xmit_fifo_size; 1161 1162 if (up->port.type == PORT_UNKNOWN) 1163 goto out; 1164 up->type_probed = up->port.type; /* XXX */ 1165 1166 /* 1167 * Reset the UART. 1168 */ 1169 #ifdef CONFIG_SERIAL_8250_RSA 1170 if (up->port.type == PORT_RSA) 1171 serial_outp(up, UART_RSA_FRR, 0); 1172 #endif 1173 serial_outp(up, UART_MCR, save_mcr); 1174 serial_outp(up, UART_FCR, (UART_FCR_ENABLE_FIFO | 1175 UART_FCR_CLEAR_RCVR | 1176 UART_FCR_CLEAR_XMIT)); 1177 serial_outp(up, UART_FCR, 0); 1178 (void)serial_in(up, UART_RX); 1179 serial_outp(up, UART_IER, 0); 1180 1181 out: 1182 spin_unlock_irqrestore(&up->port.lock, flags); 1183 } 1184 1185 static struct uart_driver sunsu_reg = { 1186 .owner = THIS_MODULE, 1187 .driver_name = "sunsu", 1188 .dev_name = "ttyS", 1189 .major = TTY_MAJOR, 1190 }; 1191 1192 static int sunsu_kbd_ms_init(struct uart_sunsu_port *up) 1193 { 1194 int quot, baud; 1195 #ifdef CONFIG_SERIO 1196 struct serio *serio; 1197 #endif 1198 1199 if (up->su_type == SU_PORT_KBD) { 1200 up->cflag = B1200 | CS8 | CLOCAL | CREAD; 1201 baud = 1200; 1202 } else { 1203 up->cflag = B4800 | CS8 | CLOCAL | CREAD; 1204 baud = 4800; 1205 } 1206 quot = up->port.uartclk / (16 * baud); 1207 1208 sunsu_autoconfig(up); 1209 if (up->port.type == PORT_UNKNOWN) 1210 return -ENODEV; 1211 1212 printk("%pOF: %s port at %llx, irq %u\n", 1213 up->port.dev->of_node, 1214 (up->su_type == SU_PORT_KBD) ? "Keyboard" : "Mouse", 1215 (unsigned long long) up->port.mapbase, 1216 up->port.irq); 1217 1218 #ifdef CONFIG_SERIO 1219 serio = &up->serio; 1220 serio->port_data = up; 1221 1222 serio->id.type = SERIO_RS232; 1223 if (up->su_type == SU_PORT_KBD) { 1224 serio->id.proto = SERIO_SUNKBD; 1225 strlcpy(serio->name, "sukbd", sizeof(serio->name)); 1226 } else { 1227 serio->id.proto = SERIO_SUN; 1228 serio->id.extra = 1; 1229 strlcpy(serio->name, "sums", sizeof(serio->name)); 1230 } 1231 strlcpy(serio->phys, 1232 (!(up->port.line & 1) ? "su/serio0" : "su/serio1"), 1233 sizeof(serio->phys)); 1234 1235 serio->write = sunsu_serio_write; 1236 serio->open = sunsu_serio_open; 1237 serio->close = sunsu_serio_close; 1238 serio->dev.parent = up->port.dev; 1239 1240 serio_register_port(serio); 1241 #endif 1242 1243 sunsu_change_speed(&up->port, up->cflag, 0, quot); 1244 1245 sunsu_startup(&up->port); 1246 return 0; 1247 } 1248 1249 /* 1250 * ------------------------------------------------------------ 1251 * Serial console driver 1252 * ------------------------------------------------------------ 1253 */ 1254 1255 #ifdef CONFIG_SERIAL_SUNSU_CONSOLE 1256 1257 #define BOTH_EMPTY (UART_LSR_TEMT | UART_LSR_THRE) 1258 1259 /* 1260 * Wait for transmitter & holding register to empty 1261 */ 1262 static void wait_for_xmitr(struct uart_sunsu_port *up) 1263 { 1264 unsigned int status, tmout = 10000; 1265 1266 /* Wait up to 10ms for the character(s) to be sent. */ 1267 do { 1268 status = serial_in(up, UART_LSR); 1269 1270 if (status & UART_LSR_BI) 1271 up->lsr_break_flag = UART_LSR_BI; 1272 1273 if (--tmout == 0) 1274 break; 1275 udelay(1); 1276 } while ((status & BOTH_EMPTY) != BOTH_EMPTY); 1277 1278 /* Wait up to 1s for flow control if necessary */ 1279 if (up->port.flags & UPF_CONS_FLOW) { 1280 tmout = 1000000; 1281 while (--tmout && 1282 ((serial_in(up, UART_MSR) & UART_MSR_CTS) == 0)) 1283 udelay(1); 1284 } 1285 } 1286 1287 static void sunsu_console_putchar(struct uart_port *port, int ch) 1288 { 1289 struct uart_sunsu_port *up = 1290 container_of(port, struct uart_sunsu_port, port); 1291 1292 wait_for_xmitr(up); 1293 serial_out(up, UART_TX, ch); 1294 } 1295 1296 /* 1297 * Print a string to the serial port trying not to disturb 1298 * any possible real use of the port... 1299 */ 1300 static void sunsu_console_write(struct console *co, const char *s, 1301 unsigned int count) 1302 { 1303 struct uart_sunsu_port *up = &sunsu_ports[co->index]; 1304 unsigned long flags; 1305 unsigned int ier; 1306 int locked = 1; 1307 1308 if (up->port.sysrq || oops_in_progress) 1309 locked = spin_trylock_irqsave(&up->port.lock, flags); 1310 else 1311 spin_lock_irqsave(&up->port.lock, flags); 1312 1313 /* 1314 * First save the UER then disable the interrupts 1315 */ 1316 ier = serial_in(up, UART_IER); 1317 serial_out(up, UART_IER, 0); 1318 1319 uart_console_write(&up->port, s, count, sunsu_console_putchar); 1320 1321 /* 1322 * Finally, wait for transmitter to become empty 1323 * and restore the IER 1324 */ 1325 wait_for_xmitr(up); 1326 serial_out(up, UART_IER, ier); 1327 1328 if (locked) 1329 spin_unlock_irqrestore(&up->port.lock, flags); 1330 } 1331 1332 /* 1333 * Setup initial baud/bits/parity. We do two things here: 1334 * - construct a cflag setting for the first su_open() 1335 * - initialize the serial port 1336 * Return non-zero if we didn't find a serial port. 1337 */ 1338 static int __init sunsu_console_setup(struct console *co, char *options) 1339 { 1340 static struct ktermios dummy; 1341 struct ktermios termios; 1342 struct uart_port *port; 1343 1344 printk("Console: ttyS%d (SU)\n", 1345 (sunsu_reg.minor - 64) + co->index); 1346 1347 if (co->index > nr_inst) 1348 return -ENODEV; 1349 port = &sunsu_ports[co->index].port; 1350 1351 /* 1352 * Temporary fix. 1353 */ 1354 spin_lock_init(&port->lock); 1355 1356 /* Get firmware console settings. */ 1357 sunserial_console_termios(co, port->dev->of_node); 1358 1359 memset(&termios, 0, sizeof(struct ktermios)); 1360 termios.c_cflag = co->cflag; 1361 port->mctrl |= TIOCM_DTR; 1362 port->ops->set_termios(port, &termios, &dummy); 1363 1364 return 0; 1365 } 1366 1367 static struct console sunsu_console = { 1368 .name = "ttyS", 1369 .write = sunsu_console_write, 1370 .device = uart_console_device, 1371 .setup = sunsu_console_setup, 1372 .flags = CON_PRINTBUFFER, 1373 .index = -1, 1374 .data = &sunsu_reg, 1375 }; 1376 1377 /* 1378 * Register console. 1379 */ 1380 1381 static inline struct console *SUNSU_CONSOLE(void) 1382 { 1383 return &sunsu_console; 1384 } 1385 #else 1386 #define SUNSU_CONSOLE() (NULL) 1387 #define sunsu_serial_console_init() do { } while (0) 1388 #endif 1389 1390 static enum su_type su_get_type(struct device_node *dp) 1391 { 1392 struct device_node *ap = of_find_node_by_path("/aliases"); 1393 enum su_type rc = SU_PORT_PORT; 1394 1395 if (ap) { 1396 const char *keyb = of_get_property(ap, "keyboard", NULL); 1397 const char *ms = of_get_property(ap, "mouse", NULL); 1398 struct device_node *match; 1399 1400 if (keyb) { 1401 match = of_find_node_by_path(keyb); 1402 1403 /* 1404 * The pointer is used as an identifier not 1405 * as a pointer, we can drop the refcount on 1406 * the of__node immediately after getting it. 1407 */ 1408 of_node_put(match); 1409 1410 if (dp == match) { 1411 rc = SU_PORT_KBD; 1412 goto out; 1413 } 1414 } 1415 if (ms) { 1416 match = of_find_node_by_path(ms); 1417 1418 of_node_put(match); 1419 1420 if (dp == match) { 1421 rc = SU_PORT_MS; 1422 goto out; 1423 } 1424 } 1425 } 1426 1427 out: 1428 of_node_put(ap); 1429 return rc; 1430 } 1431 1432 static int su_probe(struct platform_device *op) 1433 { 1434 struct device_node *dp = op->dev.of_node; 1435 struct uart_sunsu_port *up; 1436 struct resource *rp; 1437 enum su_type type; 1438 bool ignore_line; 1439 int err; 1440 1441 type = su_get_type(dp); 1442 if (type == SU_PORT_PORT) { 1443 if (nr_inst >= UART_NR) 1444 return -EINVAL; 1445 up = &sunsu_ports[nr_inst]; 1446 } else { 1447 up = kzalloc(sizeof(*up), GFP_KERNEL); 1448 if (!up) 1449 return -ENOMEM; 1450 } 1451 1452 up->port.line = nr_inst; 1453 1454 spin_lock_init(&up->port.lock); 1455 1456 up->su_type = type; 1457 1458 rp = &op->resource[0]; 1459 up->port.mapbase = rp->start; 1460 up->reg_size = resource_size(rp); 1461 up->port.membase = of_ioremap(rp, 0, up->reg_size, "su"); 1462 if (!up->port.membase) { 1463 if (type != SU_PORT_PORT) 1464 kfree(up); 1465 return -ENOMEM; 1466 } 1467 1468 up->port.irq = op->archdata.irqs[0]; 1469 1470 up->port.dev = &op->dev; 1471 1472 up->port.type = PORT_UNKNOWN; 1473 up->port.uartclk = (SU_BASE_BAUD * 16); 1474 up->port.has_sysrq = IS_ENABLED(CONFIG_SERIAL_SUNSU_CONSOLE); 1475 1476 err = 0; 1477 if (up->su_type == SU_PORT_KBD || up->su_type == SU_PORT_MS) { 1478 err = sunsu_kbd_ms_init(up); 1479 if (err) { 1480 of_iounmap(&op->resource[0], 1481 up->port.membase, up->reg_size); 1482 kfree(up); 1483 return err; 1484 } 1485 platform_set_drvdata(op, up); 1486 1487 nr_inst++; 1488 1489 return 0; 1490 } 1491 1492 up->port.flags |= UPF_BOOT_AUTOCONF; 1493 1494 sunsu_autoconfig(up); 1495 1496 err = -ENODEV; 1497 if (up->port.type == PORT_UNKNOWN) 1498 goto out_unmap; 1499 1500 up->port.ops = &sunsu_pops; 1501 1502 ignore_line = false; 1503 if (of_node_name_eq(dp, "rsc-console") || 1504 of_node_name_eq(dp, "lom-console")) 1505 ignore_line = true; 1506 1507 sunserial_console_match(SUNSU_CONSOLE(), dp, 1508 &sunsu_reg, up->port.line, 1509 ignore_line); 1510 err = uart_add_one_port(&sunsu_reg, &up->port); 1511 if (err) 1512 goto out_unmap; 1513 1514 platform_set_drvdata(op, up); 1515 1516 nr_inst++; 1517 1518 return 0; 1519 1520 out_unmap: 1521 of_iounmap(&op->resource[0], up->port.membase, up->reg_size); 1522 kfree(up); 1523 return err; 1524 } 1525 1526 static int su_remove(struct platform_device *op) 1527 { 1528 struct uart_sunsu_port *up = platform_get_drvdata(op); 1529 bool kbdms = false; 1530 1531 if (up->su_type == SU_PORT_MS || 1532 up->su_type == SU_PORT_KBD) 1533 kbdms = true; 1534 1535 if (kbdms) { 1536 #ifdef CONFIG_SERIO 1537 serio_unregister_port(&up->serio); 1538 #endif 1539 } else if (up->port.type != PORT_UNKNOWN) 1540 uart_remove_one_port(&sunsu_reg, &up->port); 1541 1542 if (up->port.membase) 1543 of_iounmap(&op->resource[0], up->port.membase, up->reg_size); 1544 1545 if (kbdms) 1546 kfree(up); 1547 1548 return 0; 1549 } 1550 1551 static const struct of_device_id su_match[] = { 1552 { 1553 .name = "su", 1554 }, 1555 { 1556 .name = "su_pnp", 1557 }, 1558 { 1559 .name = "serial", 1560 .compatible = "su", 1561 }, 1562 { 1563 .type = "serial", 1564 .compatible = "su", 1565 }, 1566 {}, 1567 }; 1568 MODULE_DEVICE_TABLE(of, su_match); 1569 1570 static struct platform_driver su_driver = { 1571 .driver = { 1572 .name = "su", 1573 .of_match_table = su_match, 1574 }, 1575 .probe = su_probe, 1576 .remove = su_remove, 1577 }; 1578 1579 static int __init sunsu_init(void) 1580 { 1581 struct device_node *dp; 1582 int err; 1583 int num_uart = 0; 1584 1585 for_each_node_by_name(dp, "su") { 1586 if (su_get_type(dp) == SU_PORT_PORT) 1587 num_uart++; 1588 } 1589 for_each_node_by_name(dp, "su_pnp") { 1590 if (su_get_type(dp) == SU_PORT_PORT) 1591 num_uart++; 1592 } 1593 for_each_node_by_name(dp, "serial") { 1594 if (of_device_is_compatible(dp, "su")) { 1595 if (su_get_type(dp) == SU_PORT_PORT) 1596 num_uart++; 1597 } 1598 } 1599 for_each_node_by_type(dp, "serial") { 1600 if (of_device_is_compatible(dp, "su")) { 1601 if (su_get_type(dp) == SU_PORT_PORT) 1602 num_uart++; 1603 } 1604 } 1605 1606 if (num_uart) { 1607 err = sunserial_register_minors(&sunsu_reg, num_uart); 1608 if (err) 1609 return err; 1610 } 1611 1612 err = platform_driver_register(&su_driver); 1613 if (err && num_uart) 1614 sunserial_unregister_minors(&sunsu_reg, num_uart); 1615 1616 return err; 1617 } 1618 1619 static void __exit sunsu_exit(void) 1620 { 1621 platform_driver_unregister(&su_driver); 1622 if (sunsu_reg.nr) 1623 sunserial_unregister_minors(&sunsu_reg, sunsu_reg.nr); 1624 } 1625 1626 module_init(sunsu_init); 1627 module_exit(sunsu_exit); 1628 1629 MODULE_AUTHOR("Eddie C. Dost, Peter Zaitcev, and David S. Miller"); 1630 MODULE_DESCRIPTION("Sun SU serial port driver"); 1631 MODULE_VERSION("2.0"); 1632 MODULE_LICENSE("GPL"); 1633