1 // SPDX-License-Identifier: GPL-2.0 2 /* sunsab.c: ASYNC Driver for the SIEMENS SAB82532 DUSCC. 3 * 4 * Copyright (C) 1997 Eddie C. Dost (ecd@skynet.be) 5 * Copyright (C) 2002, 2006 David S. Miller (davem@davemloft.net) 6 * 7 * Rewrote buffer handling to use CIRC(Circular Buffer) macros. 8 * Maxim Krasnyanskiy <maxk@qualcomm.com> 9 * 10 * Fixed to use tty_get_baud_rate, and to allow for arbitrary baud 11 * rates to be programmed into the UART. Also eliminated a lot of 12 * duplicated code in the console setup. 13 * Theodore Ts'o <tytso@mit.edu>, 2001-Oct-12 14 * 15 * Ported to new 2.5.x UART layer. 16 * David S. Miller <davem@davemloft.net> 17 */ 18 19 #include <linux/module.h> 20 #include <linux/kernel.h> 21 #include <linux/errno.h> 22 #include <linux/tty.h> 23 #include <linux/tty_flip.h> 24 #include <linux/major.h> 25 #include <linux/string.h> 26 #include <linux/ptrace.h> 27 #include <linux/ioport.h> 28 #include <linux/circ_buf.h> 29 #include <linux/serial.h> 30 #include <linux/sysrq.h> 31 #include <linux/console.h> 32 #include <linux/spinlock.h> 33 #include <linux/slab.h> 34 #include <linux/delay.h> 35 #include <linux/init.h> 36 #include <linux/of_device.h> 37 38 #include <asm/io.h> 39 #include <asm/irq.h> 40 #include <asm/prom.h> 41 #include <asm/setup.h> 42 43 #if defined(CONFIG_SERIAL_SUNSAB_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ) 44 #define SUPPORT_SYSRQ 45 #endif 46 47 #include <linux/serial_core.h> 48 #include <linux/sunserialcore.h> 49 50 #include "sunsab.h" 51 52 struct uart_sunsab_port { 53 struct uart_port port; /* Generic UART port */ 54 union sab82532_async_regs __iomem *regs; /* Chip registers */ 55 unsigned long irqflags; /* IRQ state flags */ 56 int dsr; /* Current DSR state */ 57 unsigned int cec_timeout; /* Chip poll timeout... */ 58 unsigned int tec_timeout; /* likewise */ 59 unsigned char interrupt_mask0;/* ISR0 masking */ 60 unsigned char interrupt_mask1;/* ISR1 masking */ 61 unsigned char pvr_dtr_bit; /* Which PVR bit is DTR */ 62 unsigned char pvr_dsr_bit; /* Which PVR bit is DSR */ 63 unsigned int gis_shift; 64 int type; /* SAB82532 version */ 65 66 /* Setting configuration bits while the transmitter is active 67 * can cause garbage characters to get emitted by the chip. 68 * Therefore, we cache such writes here and do the real register 69 * write the next time the transmitter becomes idle. 70 */ 71 unsigned int cached_ebrg; 72 unsigned char cached_mode; 73 unsigned char cached_pvr; 74 unsigned char cached_dafo; 75 }; 76 77 /* 78 * This assumes you have a 29.4912 MHz clock for your UART. 79 */ 80 #define SAB_BASE_BAUD ( 29491200 / 16 ) 81 82 static char *sab82532_version[16] = { 83 "V1.0", "V2.0", "V3.2", "V(0x03)", 84 "V(0x04)", "V(0x05)", "V(0x06)", "V(0x07)", 85 "V(0x08)", "V(0x09)", "V(0x0a)", "V(0x0b)", 86 "V(0x0c)", "V(0x0d)", "V(0x0e)", "V(0x0f)" 87 }; 88 89 #define SAB82532_MAX_TEC_TIMEOUT 200000 /* 1 character time (at 50 baud) */ 90 #define SAB82532_MAX_CEC_TIMEOUT 50000 /* 2.5 TX CLKs (at 50 baud) */ 91 92 #define SAB82532_RECV_FIFO_SIZE 32 /* Standard async fifo sizes */ 93 #define SAB82532_XMIT_FIFO_SIZE 32 94 95 static __inline__ void sunsab_tec_wait(struct uart_sunsab_port *up) 96 { 97 int timeout = up->tec_timeout; 98 99 while ((readb(&up->regs->r.star) & SAB82532_STAR_TEC) && --timeout) 100 udelay(1); 101 } 102 103 static __inline__ void sunsab_cec_wait(struct uart_sunsab_port *up) 104 { 105 int timeout = up->cec_timeout; 106 107 while ((readb(&up->regs->r.star) & SAB82532_STAR_CEC) && --timeout) 108 udelay(1); 109 } 110 111 static struct tty_port * 112 receive_chars(struct uart_sunsab_port *up, 113 union sab82532_irq_status *stat) 114 { 115 struct tty_port *port = NULL; 116 unsigned char buf[32]; 117 int saw_console_brk = 0; 118 int free_fifo = 0; 119 int count = 0; 120 int i; 121 122 if (up->port.state != NULL) /* Unopened serial console */ 123 port = &up->port.state->port; 124 125 /* Read number of BYTES (Character + Status) available. */ 126 if (stat->sreg.isr0 & SAB82532_ISR0_RPF) { 127 count = SAB82532_RECV_FIFO_SIZE; 128 free_fifo++; 129 } 130 131 if (stat->sreg.isr0 & SAB82532_ISR0_TCD) { 132 count = readb(&up->regs->r.rbcl) & (SAB82532_RECV_FIFO_SIZE - 1); 133 free_fifo++; 134 } 135 136 /* Issue a FIFO read command in case we where idle. */ 137 if (stat->sreg.isr0 & SAB82532_ISR0_TIME) { 138 sunsab_cec_wait(up); 139 writeb(SAB82532_CMDR_RFRD, &up->regs->w.cmdr); 140 return port; 141 } 142 143 if (stat->sreg.isr0 & SAB82532_ISR0_RFO) 144 free_fifo++; 145 146 /* Read the FIFO. */ 147 for (i = 0; i < count; i++) 148 buf[i] = readb(&up->regs->r.rfifo[i]); 149 150 /* Issue Receive Message Complete command. */ 151 if (free_fifo) { 152 sunsab_cec_wait(up); 153 writeb(SAB82532_CMDR_RMC, &up->regs->w.cmdr); 154 } 155 156 /* Count may be zero for BRK, so we check for it here */ 157 if ((stat->sreg.isr1 & SAB82532_ISR1_BRK) && 158 (up->port.line == up->port.cons->index)) 159 saw_console_brk = 1; 160 161 if (count == 0) { 162 if (unlikely(stat->sreg.isr1 & SAB82532_ISR1_BRK)) { 163 stat->sreg.isr0 &= ~(SAB82532_ISR0_PERR | 164 SAB82532_ISR0_FERR); 165 up->port.icount.brk++; 166 uart_handle_break(&up->port); 167 } 168 } 169 170 for (i = 0; i < count; i++) { 171 unsigned char ch = buf[i], flag; 172 173 flag = TTY_NORMAL; 174 up->port.icount.rx++; 175 176 if (unlikely(stat->sreg.isr0 & (SAB82532_ISR0_PERR | 177 SAB82532_ISR0_FERR | 178 SAB82532_ISR0_RFO)) || 179 unlikely(stat->sreg.isr1 & SAB82532_ISR1_BRK)) { 180 /* 181 * For statistics only 182 */ 183 if (stat->sreg.isr1 & SAB82532_ISR1_BRK) { 184 stat->sreg.isr0 &= ~(SAB82532_ISR0_PERR | 185 SAB82532_ISR0_FERR); 186 up->port.icount.brk++; 187 /* 188 * We do the SysRQ and SAK checking 189 * here because otherwise the break 190 * may get masked by ignore_status_mask 191 * or read_status_mask. 192 */ 193 if (uart_handle_break(&up->port)) 194 continue; 195 } else if (stat->sreg.isr0 & SAB82532_ISR0_PERR) 196 up->port.icount.parity++; 197 else if (stat->sreg.isr0 & SAB82532_ISR0_FERR) 198 up->port.icount.frame++; 199 if (stat->sreg.isr0 & SAB82532_ISR0_RFO) 200 up->port.icount.overrun++; 201 202 /* 203 * Mask off conditions which should be ingored. 204 */ 205 stat->sreg.isr0 &= (up->port.read_status_mask & 0xff); 206 stat->sreg.isr1 &= ((up->port.read_status_mask >> 8) & 0xff); 207 208 if (stat->sreg.isr1 & SAB82532_ISR1_BRK) { 209 flag = TTY_BREAK; 210 } else if (stat->sreg.isr0 & SAB82532_ISR0_PERR) 211 flag = TTY_PARITY; 212 else if (stat->sreg.isr0 & SAB82532_ISR0_FERR) 213 flag = TTY_FRAME; 214 } 215 216 if (uart_handle_sysrq_char(&up->port, ch) || !port) 217 continue; 218 219 if ((stat->sreg.isr0 & (up->port.ignore_status_mask & 0xff)) == 0 && 220 (stat->sreg.isr1 & ((up->port.ignore_status_mask >> 8) & 0xff)) == 0) 221 tty_insert_flip_char(port, ch, flag); 222 if (stat->sreg.isr0 & SAB82532_ISR0_RFO) 223 tty_insert_flip_char(port, 0, TTY_OVERRUN); 224 } 225 226 if (saw_console_brk) 227 sun_do_break(); 228 229 return port; 230 } 231 232 static void sunsab_stop_tx(struct uart_port *); 233 static void sunsab_tx_idle(struct uart_sunsab_port *); 234 235 static void transmit_chars(struct uart_sunsab_port *up, 236 union sab82532_irq_status *stat) 237 { 238 struct circ_buf *xmit = &up->port.state->xmit; 239 int i; 240 241 if (stat->sreg.isr1 & SAB82532_ISR1_ALLS) { 242 up->interrupt_mask1 |= SAB82532_IMR1_ALLS; 243 writeb(up->interrupt_mask1, &up->regs->w.imr1); 244 set_bit(SAB82532_ALLS, &up->irqflags); 245 } 246 247 #if 0 /* bde@nwlink.com says this check causes problems */ 248 if (!(stat->sreg.isr1 & SAB82532_ISR1_XPR)) 249 return; 250 #endif 251 252 if (!(readb(&up->regs->r.star) & SAB82532_STAR_XFW)) 253 return; 254 255 set_bit(SAB82532_XPR, &up->irqflags); 256 sunsab_tx_idle(up); 257 258 if (uart_circ_empty(xmit) || uart_tx_stopped(&up->port)) { 259 up->interrupt_mask1 |= SAB82532_IMR1_XPR; 260 writeb(up->interrupt_mask1, &up->regs->w.imr1); 261 return; 262 } 263 264 up->interrupt_mask1 &= ~(SAB82532_IMR1_ALLS|SAB82532_IMR1_XPR); 265 writeb(up->interrupt_mask1, &up->regs->w.imr1); 266 clear_bit(SAB82532_ALLS, &up->irqflags); 267 268 /* Stuff 32 bytes into Transmit FIFO. */ 269 clear_bit(SAB82532_XPR, &up->irqflags); 270 for (i = 0; i < up->port.fifosize; i++) { 271 writeb(xmit->buf[xmit->tail], 272 &up->regs->w.xfifo[i]); 273 xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1); 274 up->port.icount.tx++; 275 if (uart_circ_empty(xmit)) 276 break; 277 } 278 279 /* Issue a Transmit Frame command. */ 280 sunsab_cec_wait(up); 281 writeb(SAB82532_CMDR_XF, &up->regs->w.cmdr); 282 283 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) 284 uart_write_wakeup(&up->port); 285 286 if (uart_circ_empty(xmit)) 287 sunsab_stop_tx(&up->port); 288 } 289 290 static void check_status(struct uart_sunsab_port *up, 291 union sab82532_irq_status *stat) 292 { 293 if (stat->sreg.isr0 & SAB82532_ISR0_CDSC) 294 uart_handle_dcd_change(&up->port, 295 !(readb(&up->regs->r.vstr) & SAB82532_VSTR_CD)); 296 297 if (stat->sreg.isr1 & SAB82532_ISR1_CSC) 298 uart_handle_cts_change(&up->port, 299 (readb(&up->regs->r.star) & SAB82532_STAR_CTS)); 300 301 if ((readb(&up->regs->r.pvr) & up->pvr_dsr_bit) ^ up->dsr) { 302 up->dsr = (readb(&up->regs->r.pvr) & up->pvr_dsr_bit) ? 0 : 1; 303 up->port.icount.dsr++; 304 } 305 306 wake_up_interruptible(&up->port.state->port.delta_msr_wait); 307 } 308 309 static irqreturn_t sunsab_interrupt(int irq, void *dev_id) 310 { 311 struct uart_sunsab_port *up = dev_id; 312 struct tty_port *port = NULL; 313 union sab82532_irq_status status; 314 unsigned long flags; 315 unsigned char gis; 316 317 spin_lock_irqsave(&up->port.lock, flags); 318 319 status.stat = 0; 320 gis = readb(&up->regs->r.gis) >> up->gis_shift; 321 if (gis & 1) 322 status.sreg.isr0 = readb(&up->regs->r.isr0); 323 if (gis & 2) 324 status.sreg.isr1 = readb(&up->regs->r.isr1); 325 326 if (status.stat) { 327 if ((status.sreg.isr0 & (SAB82532_ISR0_TCD | SAB82532_ISR0_TIME | 328 SAB82532_ISR0_RFO | SAB82532_ISR0_RPF)) || 329 (status.sreg.isr1 & SAB82532_ISR1_BRK)) 330 port = receive_chars(up, &status); 331 if ((status.sreg.isr0 & SAB82532_ISR0_CDSC) || 332 (status.sreg.isr1 & SAB82532_ISR1_CSC)) 333 check_status(up, &status); 334 if (status.sreg.isr1 & (SAB82532_ISR1_ALLS | SAB82532_ISR1_XPR)) 335 transmit_chars(up, &status); 336 } 337 338 spin_unlock_irqrestore(&up->port.lock, flags); 339 340 if (port) 341 tty_flip_buffer_push(port); 342 343 return IRQ_HANDLED; 344 } 345 346 /* port->lock is not held. */ 347 static unsigned int sunsab_tx_empty(struct uart_port *port) 348 { 349 struct uart_sunsab_port *up = 350 container_of(port, struct uart_sunsab_port, port); 351 int ret; 352 353 /* Do not need a lock for a state test like this. */ 354 if (test_bit(SAB82532_ALLS, &up->irqflags)) 355 ret = TIOCSER_TEMT; 356 else 357 ret = 0; 358 359 return ret; 360 } 361 362 /* port->lock held by caller. */ 363 static void sunsab_set_mctrl(struct uart_port *port, unsigned int mctrl) 364 { 365 struct uart_sunsab_port *up = 366 container_of(port, struct uart_sunsab_port, port); 367 368 if (mctrl & TIOCM_RTS) { 369 up->cached_mode &= ~SAB82532_MODE_FRTS; 370 up->cached_mode |= SAB82532_MODE_RTS; 371 } else { 372 up->cached_mode |= (SAB82532_MODE_FRTS | 373 SAB82532_MODE_RTS); 374 } 375 if (mctrl & TIOCM_DTR) { 376 up->cached_pvr &= ~(up->pvr_dtr_bit); 377 } else { 378 up->cached_pvr |= up->pvr_dtr_bit; 379 } 380 381 set_bit(SAB82532_REGS_PENDING, &up->irqflags); 382 if (test_bit(SAB82532_XPR, &up->irqflags)) 383 sunsab_tx_idle(up); 384 } 385 386 /* port->lock is held by caller and interrupts are disabled. */ 387 static unsigned int sunsab_get_mctrl(struct uart_port *port) 388 { 389 struct uart_sunsab_port *up = 390 container_of(port, struct uart_sunsab_port, port); 391 unsigned char val; 392 unsigned int result; 393 394 result = 0; 395 396 val = readb(&up->regs->r.pvr); 397 result |= (val & up->pvr_dsr_bit) ? 0 : TIOCM_DSR; 398 399 val = readb(&up->regs->r.vstr); 400 result |= (val & SAB82532_VSTR_CD) ? 0 : TIOCM_CAR; 401 402 val = readb(&up->regs->r.star); 403 result |= (val & SAB82532_STAR_CTS) ? TIOCM_CTS : 0; 404 405 return result; 406 } 407 408 /* port->lock held by caller. */ 409 static void sunsab_stop_tx(struct uart_port *port) 410 { 411 struct uart_sunsab_port *up = 412 container_of(port, struct uart_sunsab_port, port); 413 414 up->interrupt_mask1 |= SAB82532_IMR1_XPR; 415 writeb(up->interrupt_mask1, &up->regs->w.imr1); 416 } 417 418 /* port->lock held by caller. */ 419 static void sunsab_tx_idle(struct uart_sunsab_port *up) 420 { 421 if (test_bit(SAB82532_REGS_PENDING, &up->irqflags)) { 422 u8 tmp; 423 424 clear_bit(SAB82532_REGS_PENDING, &up->irqflags); 425 writeb(up->cached_mode, &up->regs->rw.mode); 426 writeb(up->cached_pvr, &up->regs->rw.pvr); 427 writeb(up->cached_dafo, &up->regs->w.dafo); 428 429 writeb(up->cached_ebrg & 0xff, &up->regs->w.bgr); 430 tmp = readb(&up->regs->rw.ccr2); 431 tmp &= ~0xc0; 432 tmp |= (up->cached_ebrg >> 2) & 0xc0; 433 writeb(tmp, &up->regs->rw.ccr2); 434 } 435 } 436 437 /* port->lock held by caller. */ 438 static void sunsab_start_tx(struct uart_port *port) 439 { 440 struct uart_sunsab_port *up = 441 container_of(port, struct uart_sunsab_port, port); 442 struct circ_buf *xmit = &up->port.state->xmit; 443 int i; 444 445 if (uart_circ_empty(xmit) || uart_tx_stopped(port)) 446 return; 447 448 up->interrupt_mask1 &= ~(SAB82532_IMR1_ALLS|SAB82532_IMR1_XPR); 449 writeb(up->interrupt_mask1, &up->regs->w.imr1); 450 451 if (!test_bit(SAB82532_XPR, &up->irqflags)) 452 return; 453 454 clear_bit(SAB82532_ALLS, &up->irqflags); 455 clear_bit(SAB82532_XPR, &up->irqflags); 456 457 for (i = 0; i < up->port.fifosize; i++) { 458 writeb(xmit->buf[xmit->tail], 459 &up->regs->w.xfifo[i]); 460 xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1); 461 up->port.icount.tx++; 462 if (uart_circ_empty(xmit)) 463 break; 464 } 465 466 /* Issue a Transmit Frame command. */ 467 sunsab_cec_wait(up); 468 writeb(SAB82532_CMDR_XF, &up->regs->w.cmdr); 469 } 470 471 /* port->lock is not held. */ 472 static void sunsab_send_xchar(struct uart_port *port, char ch) 473 { 474 struct uart_sunsab_port *up = 475 container_of(port, struct uart_sunsab_port, port); 476 unsigned long flags; 477 478 if (ch == __DISABLED_CHAR) 479 return; 480 481 spin_lock_irqsave(&up->port.lock, flags); 482 483 sunsab_tec_wait(up); 484 writeb(ch, &up->regs->w.tic); 485 486 spin_unlock_irqrestore(&up->port.lock, flags); 487 } 488 489 /* port->lock held by caller. */ 490 static void sunsab_stop_rx(struct uart_port *port) 491 { 492 struct uart_sunsab_port *up = 493 container_of(port, struct uart_sunsab_port, port); 494 495 up->interrupt_mask0 |= SAB82532_IMR0_TCD; 496 writeb(up->interrupt_mask1, &up->regs->w.imr0); 497 } 498 499 /* port->lock is not held. */ 500 static void sunsab_break_ctl(struct uart_port *port, int break_state) 501 { 502 struct uart_sunsab_port *up = 503 container_of(port, struct uart_sunsab_port, port); 504 unsigned long flags; 505 unsigned char val; 506 507 spin_lock_irqsave(&up->port.lock, flags); 508 509 val = up->cached_dafo; 510 if (break_state) 511 val |= SAB82532_DAFO_XBRK; 512 else 513 val &= ~SAB82532_DAFO_XBRK; 514 up->cached_dafo = val; 515 516 set_bit(SAB82532_REGS_PENDING, &up->irqflags); 517 if (test_bit(SAB82532_XPR, &up->irqflags)) 518 sunsab_tx_idle(up); 519 520 spin_unlock_irqrestore(&up->port.lock, flags); 521 } 522 523 /* port->lock is not held. */ 524 static int sunsab_startup(struct uart_port *port) 525 { 526 struct uart_sunsab_port *up = 527 container_of(port, struct uart_sunsab_port, port); 528 unsigned long flags; 529 unsigned char tmp; 530 int err = request_irq(up->port.irq, sunsab_interrupt, 531 IRQF_SHARED, "sab", up); 532 if (err) 533 return err; 534 535 spin_lock_irqsave(&up->port.lock, flags); 536 537 /* 538 * Wait for any commands or immediate characters 539 */ 540 sunsab_cec_wait(up); 541 sunsab_tec_wait(up); 542 543 /* 544 * Clear the FIFO buffers. 545 */ 546 writeb(SAB82532_CMDR_RRES, &up->regs->w.cmdr); 547 sunsab_cec_wait(up); 548 writeb(SAB82532_CMDR_XRES, &up->regs->w.cmdr); 549 550 /* 551 * Clear the interrupt registers. 552 */ 553 (void) readb(&up->regs->r.isr0); 554 (void) readb(&up->regs->r.isr1); 555 556 /* 557 * Now, initialize the UART 558 */ 559 writeb(0, &up->regs->w.ccr0); /* power-down */ 560 writeb(SAB82532_CCR0_MCE | SAB82532_CCR0_SC_NRZ | 561 SAB82532_CCR0_SM_ASYNC, &up->regs->w.ccr0); 562 writeb(SAB82532_CCR1_ODS | SAB82532_CCR1_BCR | 7, &up->regs->w.ccr1); 563 writeb(SAB82532_CCR2_BDF | SAB82532_CCR2_SSEL | 564 SAB82532_CCR2_TOE, &up->regs->w.ccr2); 565 writeb(0, &up->regs->w.ccr3); 566 writeb(SAB82532_CCR4_MCK4 | SAB82532_CCR4_EBRG, &up->regs->w.ccr4); 567 up->cached_mode = (SAB82532_MODE_RTS | SAB82532_MODE_FCTS | 568 SAB82532_MODE_RAC); 569 writeb(up->cached_mode, &up->regs->w.mode); 570 writeb(SAB82532_RFC_DPS|SAB82532_RFC_RFTH_32, &up->regs->w.rfc); 571 572 tmp = readb(&up->regs->rw.ccr0); 573 tmp |= SAB82532_CCR0_PU; /* power-up */ 574 writeb(tmp, &up->regs->rw.ccr0); 575 576 /* 577 * Finally, enable interrupts 578 */ 579 up->interrupt_mask0 = (SAB82532_IMR0_PERR | SAB82532_IMR0_FERR | 580 SAB82532_IMR0_PLLA); 581 writeb(up->interrupt_mask0, &up->regs->w.imr0); 582 up->interrupt_mask1 = (SAB82532_IMR1_BRKT | SAB82532_IMR1_ALLS | 583 SAB82532_IMR1_XOFF | SAB82532_IMR1_TIN | 584 SAB82532_IMR1_CSC | SAB82532_IMR1_XON | 585 SAB82532_IMR1_XPR); 586 writeb(up->interrupt_mask1, &up->regs->w.imr1); 587 set_bit(SAB82532_ALLS, &up->irqflags); 588 set_bit(SAB82532_XPR, &up->irqflags); 589 590 spin_unlock_irqrestore(&up->port.lock, flags); 591 592 return 0; 593 } 594 595 /* port->lock is not held. */ 596 static void sunsab_shutdown(struct uart_port *port) 597 { 598 struct uart_sunsab_port *up = 599 container_of(port, struct uart_sunsab_port, port); 600 unsigned long flags; 601 602 spin_lock_irqsave(&up->port.lock, flags); 603 604 /* Disable Interrupts */ 605 up->interrupt_mask0 = 0xff; 606 writeb(up->interrupt_mask0, &up->regs->w.imr0); 607 up->interrupt_mask1 = 0xff; 608 writeb(up->interrupt_mask1, &up->regs->w.imr1); 609 610 /* Disable break condition */ 611 up->cached_dafo = readb(&up->regs->rw.dafo); 612 up->cached_dafo &= ~SAB82532_DAFO_XBRK; 613 writeb(up->cached_dafo, &up->regs->rw.dafo); 614 615 /* Disable Receiver */ 616 up->cached_mode &= ~SAB82532_MODE_RAC; 617 writeb(up->cached_mode, &up->regs->rw.mode); 618 619 /* 620 * XXX FIXME 621 * 622 * If the chip is powered down here the system hangs/crashes during 623 * reboot or shutdown. This needs to be investigated further, 624 * similar behaviour occurs in 2.4 when the driver is configured 625 * as a module only. One hint may be that data is sometimes 626 * transmitted at 9600 baud during shutdown (regardless of the 627 * speed the chip was configured for when the port was open). 628 */ 629 #if 0 630 /* Power Down */ 631 tmp = readb(&up->regs->rw.ccr0); 632 tmp &= ~SAB82532_CCR0_PU; 633 writeb(tmp, &up->regs->rw.ccr0); 634 #endif 635 636 spin_unlock_irqrestore(&up->port.lock, flags); 637 free_irq(up->port.irq, up); 638 } 639 640 /* 641 * This is used to figure out the divisor speeds. 642 * 643 * The formula is: Baud = SAB_BASE_BAUD / ((N + 1) * (1 << M)), 644 * 645 * with 0 <= N < 64 and 0 <= M < 16 646 */ 647 648 static void calc_ebrg(int baud, int *n_ret, int *m_ret) 649 { 650 int n, m; 651 652 if (baud == 0) { 653 *n_ret = 0; 654 *m_ret = 0; 655 return; 656 } 657 658 /* 659 * We scale numbers by 10 so that we get better accuracy 660 * without having to use floating point. Here we increment m 661 * until n is within the valid range. 662 */ 663 n = (SAB_BASE_BAUD * 10) / baud; 664 m = 0; 665 while (n >= 640) { 666 n = n / 2; 667 m++; 668 } 669 n = (n+5) / 10; 670 /* 671 * We try very hard to avoid speeds with M == 0 since they may 672 * not work correctly for XTAL frequences above 10 MHz. 673 */ 674 if ((m == 0) && ((n & 1) == 0)) { 675 n = n / 2; 676 m++; 677 } 678 *n_ret = n - 1; 679 *m_ret = m; 680 } 681 682 /* Internal routine, port->lock is held and local interrupts are disabled. */ 683 static void sunsab_convert_to_sab(struct uart_sunsab_port *up, unsigned int cflag, 684 unsigned int iflag, unsigned int baud, 685 unsigned int quot) 686 { 687 unsigned char dafo; 688 int bits, n, m; 689 690 /* Byte size and parity */ 691 switch (cflag & CSIZE) { 692 case CS5: dafo = SAB82532_DAFO_CHL5; bits = 7; break; 693 case CS6: dafo = SAB82532_DAFO_CHL6; bits = 8; break; 694 case CS7: dafo = SAB82532_DAFO_CHL7; bits = 9; break; 695 case CS8: dafo = SAB82532_DAFO_CHL8; bits = 10; break; 696 /* Never happens, but GCC is too dumb to figure it out */ 697 default: dafo = SAB82532_DAFO_CHL5; bits = 7; break; 698 } 699 700 if (cflag & CSTOPB) { 701 dafo |= SAB82532_DAFO_STOP; 702 bits++; 703 } 704 705 if (cflag & PARENB) { 706 dafo |= SAB82532_DAFO_PARE; 707 bits++; 708 } 709 710 if (cflag & PARODD) { 711 dafo |= SAB82532_DAFO_PAR_ODD; 712 } else { 713 dafo |= SAB82532_DAFO_PAR_EVEN; 714 } 715 up->cached_dafo = dafo; 716 717 calc_ebrg(baud, &n, &m); 718 719 up->cached_ebrg = n | (m << 6); 720 721 up->tec_timeout = (10 * 1000000) / baud; 722 up->cec_timeout = up->tec_timeout >> 2; 723 724 /* CTS flow control flags */ 725 /* We encode read_status_mask and ignore_status_mask like so: 726 * 727 * --------------------- 728 * | ... | ISR1 | ISR0 | 729 * --------------------- 730 * .. 15 8 7 0 731 */ 732 733 up->port.read_status_mask = (SAB82532_ISR0_TCD | SAB82532_ISR0_TIME | 734 SAB82532_ISR0_RFO | SAB82532_ISR0_RPF | 735 SAB82532_ISR0_CDSC); 736 up->port.read_status_mask |= (SAB82532_ISR1_CSC | 737 SAB82532_ISR1_ALLS | 738 SAB82532_ISR1_XPR) << 8; 739 if (iflag & INPCK) 740 up->port.read_status_mask |= (SAB82532_ISR0_PERR | 741 SAB82532_ISR0_FERR); 742 if (iflag & (IGNBRK | BRKINT | PARMRK)) 743 up->port.read_status_mask |= (SAB82532_ISR1_BRK << 8); 744 745 /* 746 * Characteres to ignore 747 */ 748 up->port.ignore_status_mask = 0; 749 if (iflag & IGNPAR) 750 up->port.ignore_status_mask |= (SAB82532_ISR0_PERR | 751 SAB82532_ISR0_FERR); 752 if (iflag & IGNBRK) { 753 up->port.ignore_status_mask |= (SAB82532_ISR1_BRK << 8); 754 /* 755 * If we're ignoring parity and break indicators, 756 * ignore overruns too (for real raw support). 757 */ 758 if (iflag & IGNPAR) 759 up->port.ignore_status_mask |= SAB82532_ISR0_RFO; 760 } 761 762 /* 763 * ignore all characters if CREAD is not set 764 */ 765 if ((cflag & CREAD) == 0) 766 up->port.ignore_status_mask |= (SAB82532_ISR0_RPF | 767 SAB82532_ISR0_TCD); 768 769 uart_update_timeout(&up->port, cflag, 770 (up->port.uartclk / (16 * quot))); 771 772 /* Now schedule a register update when the chip's 773 * transmitter is idle. 774 */ 775 up->cached_mode |= SAB82532_MODE_RAC; 776 set_bit(SAB82532_REGS_PENDING, &up->irqflags); 777 if (test_bit(SAB82532_XPR, &up->irqflags)) 778 sunsab_tx_idle(up); 779 } 780 781 /* port->lock is not held. */ 782 static void sunsab_set_termios(struct uart_port *port, struct ktermios *termios, 783 struct ktermios *old) 784 { 785 struct uart_sunsab_port *up = 786 container_of(port, struct uart_sunsab_port, port); 787 unsigned long flags; 788 unsigned int baud = uart_get_baud_rate(port, termios, old, 0, 4000000); 789 unsigned int quot = uart_get_divisor(port, baud); 790 791 spin_lock_irqsave(&up->port.lock, flags); 792 sunsab_convert_to_sab(up, termios->c_cflag, termios->c_iflag, baud, quot); 793 spin_unlock_irqrestore(&up->port.lock, flags); 794 } 795 796 static const char *sunsab_type(struct uart_port *port) 797 { 798 struct uart_sunsab_port *up = (void *)port; 799 static char buf[36]; 800 801 sprintf(buf, "SAB82532 %s", sab82532_version[up->type]); 802 return buf; 803 } 804 805 static void sunsab_release_port(struct uart_port *port) 806 { 807 } 808 809 static int sunsab_request_port(struct uart_port *port) 810 { 811 return 0; 812 } 813 814 static void sunsab_config_port(struct uart_port *port, int flags) 815 { 816 } 817 818 static int sunsab_verify_port(struct uart_port *port, struct serial_struct *ser) 819 { 820 return -EINVAL; 821 } 822 823 static const struct uart_ops sunsab_pops = { 824 .tx_empty = sunsab_tx_empty, 825 .set_mctrl = sunsab_set_mctrl, 826 .get_mctrl = sunsab_get_mctrl, 827 .stop_tx = sunsab_stop_tx, 828 .start_tx = sunsab_start_tx, 829 .send_xchar = sunsab_send_xchar, 830 .stop_rx = sunsab_stop_rx, 831 .break_ctl = sunsab_break_ctl, 832 .startup = sunsab_startup, 833 .shutdown = sunsab_shutdown, 834 .set_termios = sunsab_set_termios, 835 .type = sunsab_type, 836 .release_port = sunsab_release_port, 837 .request_port = sunsab_request_port, 838 .config_port = sunsab_config_port, 839 .verify_port = sunsab_verify_port, 840 }; 841 842 static struct uart_driver sunsab_reg = { 843 .owner = THIS_MODULE, 844 .driver_name = "sunsab", 845 .dev_name = "ttyS", 846 .major = TTY_MAJOR, 847 }; 848 849 static struct uart_sunsab_port *sunsab_ports; 850 851 #ifdef CONFIG_SERIAL_SUNSAB_CONSOLE 852 853 static void sunsab_console_putchar(struct uart_port *port, int c) 854 { 855 struct uart_sunsab_port *up = 856 container_of(port, struct uart_sunsab_port, port); 857 858 sunsab_tec_wait(up); 859 writeb(c, &up->regs->w.tic); 860 } 861 862 static void sunsab_console_write(struct console *con, const char *s, unsigned n) 863 { 864 struct uart_sunsab_port *up = &sunsab_ports[con->index]; 865 unsigned long flags; 866 int locked = 1; 867 868 if (up->port.sysrq || oops_in_progress) 869 locked = spin_trylock_irqsave(&up->port.lock, flags); 870 else 871 spin_lock_irqsave(&up->port.lock, flags); 872 873 uart_console_write(&up->port, s, n, sunsab_console_putchar); 874 sunsab_tec_wait(up); 875 876 if (locked) 877 spin_unlock_irqrestore(&up->port.lock, flags); 878 } 879 880 static int sunsab_console_setup(struct console *con, char *options) 881 { 882 struct uart_sunsab_port *up = &sunsab_ports[con->index]; 883 unsigned long flags; 884 unsigned int baud, quot; 885 886 /* 887 * The console framework calls us for each and every port 888 * registered. Defer the console setup until the requested 889 * port has been properly discovered. A bit of a hack, 890 * though... 891 */ 892 if (up->port.type != PORT_SUNSAB) 893 return -1; 894 895 printk("Console: ttyS%d (SAB82532)\n", 896 (sunsab_reg.minor - 64) + con->index); 897 898 sunserial_console_termios(con, up->port.dev->of_node); 899 900 switch (con->cflag & CBAUD) { 901 case B150: baud = 150; break; 902 case B300: baud = 300; break; 903 case B600: baud = 600; break; 904 case B1200: baud = 1200; break; 905 case B2400: baud = 2400; break; 906 case B4800: baud = 4800; break; 907 default: case B9600: baud = 9600; break; 908 case B19200: baud = 19200; break; 909 case B38400: baud = 38400; break; 910 case B57600: baud = 57600; break; 911 case B115200: baud = 115200; break; 912 case B230400: baud = 230400; break; 913 case B460800: baud = 460800; break; 914 } 915 916 /* 917 * Temporary fix. 918 */ 919 spin_lock_init(&up->port.lock); 920 921 /* 922 * Initialize the hardware 923 */ 924 sunsab_startup(&up->port); 925 926 spin_lock_irqsave(&up->port.lock, flags); 927 928 /* 929 * Finally, enable interrupts 930 */ 931 up->interrupt_mask0 = SAB82532_IMR0_PERR | SAB82532_IMR0_FERR | 932 SAB82532_IMR0_PLLA | SAB82532_IMR0_CDSC; 933 writeb(up->interrupt_mask0, &up->regs->w.imr0); 934 up->interrupt_mask1 = SAB82532_IMR1_BRKT | SAB82532_IMR1_ALLS | 935 SAB82532_IMR1_XOFF | SAB82532_IMR1_TIN | 936 SAB82532_IMR1_CSC | SAB82532_IMR1_XON | 937 SAB82532_IMR1_XPR; 938 writeb(up->interrupt_mask1, &up->regs->w.imr1); 939 940 quot = uart_get_divisor(&up->port, baud); 941 sunsab_convert_to_sab(up, con->cflag, 0, baud, quot); 942 sunsab_set_mctrl(&up->port, TIOCM_DTR | TIOCM_RTS); 943 944 spin_unlock_irqrestore(&up->port.lock, flags); 945 946 return 0; 947 } 948 949 static struct console sunsab_console = { 950 .name = "ttyS", 951 .write = sunsab_console_write, 952 .device = uart_console_device, 953 .setup = sunsab_console_setup, 954 .flags = CON_PRINTBUFFER, 955 .index = -1, 956 .data = &sunsab_reg, 957 }; 958 959 static inline struct console *SUNSAB_CONSOLE(void) 960 { 961 return &sunsab_console; 962 } 963 #else 964 #define SUNSAB_CONSOLE() (NULL) 965 #define sunsab_console_init() do { } while (0) 966 #endif 967 968 static int sunsab_init_one(struct uart_sunsab_port *up, 969 struct platform_device *op, 970 unsigned long offset, 971 int line) 972 { 973 up->port.line = line; 974 up->port.dev = &op->dev; 975 976 up->port.mapbase = op->resource[0].start + offset; 977 up->port.membase = of_ioremap(&op->resource[0], offset, 978 sizeof(union sab82532_async_regs), 979 "sab"); 980 if (!up->port.membase) 981 return -ENOMEM; 982 up->regs = (union sab82532_async_regs __iomem *) up->port.membase; 983 984 up->port.irq = op->archdata.irqs[0]; 985 986 up->port.fifosize = SAB82532_XMIT_FIFO_SIZE; 987 up->port.iotype = UPIO_MEM; 988 989 writeb(SAB82532_IPC_IC_ACT_LOW, &up->regs->w.ipc); 990 991 up->port.ops = &sunsab_pops; 992 up->port.type = PORT_SUNSAB; 993 up->port.uartclk = SAB_BASE_BAUD; 994 995 up->type = readb(&up->regs->r.vstr) & 0x0f; 996 writeb(~((1 << 1) | (1 << 2) | (1 << 4)), &up->regs->w.pcr); 997 writeb(0xff, &up->regs->w.pim); 998 if ((up->port.line & 0x1) == 0) { 999 up->pvr_dsr_bit = (1 << 0); 1000 up->pvr_dtr_bit = (1 << 1); 1001 up->gis_shift = 2; 1002 } else { 1003 up->pvr_dsr_bit = (1 << 3); 1004 up->pvr_dtr_bit = (1 << 2); 1005 up->gis_shift = 0; 1006 } 1007 up->cached_pvr = (1 << 1) | (1 << 2) | (1 << 4); 1008 writeb(up->cached_pvr, &up->regs->w.pvr); 1009 up->cached_mode = readb(&up->regs->rw.mode); 1010 up->cached_mode |= SAB82532_MODE_FRTS; 1011 writeb(up->cached_mode, &up->regs->rw.mode); 1012 up->cached_mode |= SAB82532_MODE_RTS; 1013 writeb(up->cached_mode, &up->regs->rw.mode); 1014 1015 up->tec_timeout = SAB82532_MAX_TEC_TIMEOUT; 1016 up->cec_timeout = SAB82532_MAX_CEC_TIMEOUT; 1017 1018 return 0; 1019 } 1020 1021 static int sab_probe(struct platform_device *op) 1022 { 1023 static int inst; 1024 struct uart_sunsab_port *up; 1025 int err; 1026 1027 up = &sunsab_ports[inst * 2]; 1028 1029 err = sunsab_init_one(&up[0], op, 1030 0, 1031 (inst * 2) + 0); 1032 if (err) 1033 goto out; 1034 1035 err = sunsab_init_one(&up[1], op, 1036 sizeof(union sab82532_async_regs), 1037 (inst * 2) + 1); 1038 if (err) 1039 goto out1; 1040 1041 sunserial_console_match(SUNSAB_CONSOLE(), op->dev.of_node, 1042 &sunsab_reg, up[0].port.line, 1043 false); 1044 1045 sunserial_console_match(SUNSAB_CONSOLE(), op->dev.of_node, 1046 &sunsab_reg, up[1].port.line, 1047 false); 1048 1049 err = uart_add_one_port(&sunsab_reg, &up[0].port); 1050 if (err) 1051 goto out2; 1052 1053 err = uart_add_one_port(&sunsab_reg, &up[1].port); 1054 if (err) 1055 goto out3; 1056 1057 platform_set_drvdata(op, &up[0]); 1058 1059 inst++; 1060 1061 return 0; 1062 1063 out3: 1064 uart_remove_one_port(&sunsab_reg, &up[0].port); 1065 out2: 1066 of_iounmap(&op->resource[0], 1067 up[1].port.membase, 1068 sizeof(union sab82532_async_regs)); 1069 out1: 1070 of_iounmap(&op->resource[0], 1071 up[0].port.membase, 1072 sizeof(union sab82532_async_regs)); 1073 out: 1074 return err; 1075 } 1076 1077 static int sab_remove(struct platform_device *op) 1078 { 1079 struct uart_sunsab_port *up = platform_get_drvdata(op); 1080 1081 uart_remove_one_port(&sunsab_reg, &up[1].port); 1082 uart_remove_one_port(&sunsab_reg, &up[0].port); 1083 of_iounmap(&op->resource[0], 1084 up[1].port.membase, 1085 sizeof(union sab82532_async_regs)); 1086 of_iounmap(&op->resource[0], 1087 up[0].port.membase, 1088 sizeof(union sab82532_async_regs)); 1089 1090 return 0; 1091 } 1092 1093 static const struct of_device_id sab_match[] = { 1094 { 1095 .name = "se", 1096 }, 1097 { 1098 .name = "serial", 1099 .compatible = "sab82532", 1100 }, 1101 {}, 1102 }; 1103 MODULE_DEVICE_TABLE(of, sab_match); 1104 1105 static struct platform_driver sab_driver = { 1106 .driver = { 1107 .name = "sab", 1108 .of_match_table = sab_match, 1109 }, 1110 .probe = sab_probe, 1111 .remove = sab_remove, 1112 }; 1113 1114 static int __init sunsab_init(void) 1115 { 1116 struct device_node *dp; 1117 int err; 1118 int num_channels = 0; 1119 1120 for_each_node_by_name(dp, "se") 1121 num_channels += 2; 1122 for_each_node_by_name(dp, "serial") { 1123 if (of_device_is_compatible(dp, "sab82532")) 1124 num_channels += 2; 1125 } 1126 1127 if (num_channels) { 1128 sunsab_ports = kcalloc(num_channels, 1129 sizeof(struct uart_sunsab_port), 1130 GFP_KERNEL); 1131 if (!sunsab_ports) 1132 return -ENOMEM; 1133 1134 err = sunserial_register_minors(&sunsab_reg, num_channels); 1135 if (err) { 1136 kfree(sunsab_ports); 1137 sunsab_ports = NULL; 1138 1139 return err; 1140 } 1141 } 1142 1143 return platform_driver_register(&sab_driver); 1144 } 1145 1146 static void __exit sunsab_exit(void) 1147 { 1148 platform_driver_unregister(&sab_driver); 1149 if (sunsab_reg.nr) { 1150 sunserial_unregister_minors(&sunsab_reg, sunsab_reg.nr); 1151 } 1152 1153 kfree(sunsab_ports); 1154 sunsab_ports = NULL; 1155 } 1156 1157 module_init(sunsab_init); 1158 module_exit(sunsab_exit); 1159 1160 MODULE_AUTHOR("Eddie C. Dost and David S. Miller"); 1161 MODULE_DESCRIPTION("Sun SAB82532 serial port driver"); 1162 MODULE_LICENSE("GPL"); 1163