1 // SPDX-License-Identifier: GPL-2.0 2 /* 3 * SuperH on-chip serial module support. (SCI with no FIFO / with FIFO) 4 * 5 * Copyright (C) 2002 - 2011 Paul Mundt 6 * Copyright (C) 2015 Glider bvba 7 * Modified to support SH7720 SCIF. Markus Brunner, Mark Jonas (Jul 2007). 8 * 9 * based off of the old drivers/char/sh-sci.c by: 10 * 11 * Copyright (C) 1999, 2000 Niibe Yutaka 12 * Copyright (C) 2000 Sugioka Toshinobu 13 * Modified to support multiple serial ports. Stuart Menefy (May 2000). 14 * Modified to support SecureEdge. David McCullough (2002) 15 * Modified to support SH7300 SCIF. Takashi Kusuda (Jun 2003). 16 * Removed SH7300 support (Jul 2007). 17 */ 18 #if defined(CONFIG_SERIAL_SH_SCI_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ) 19 #define SUPPORT_SYSRQ 20 #endif 21 22 #undef DEBUG 23 24 #include <linux/clk.h> 25 #include <linux/console.h> 26 #include <linux/ctype.h> 27 #include <linux/cpufreq.h> 28 #include <linux/delay.h> 29 #include <linux/dmaengine.h> 30 #include <linux/dma-mapping.h> 31 #include <linux/err.h> 32 #include <linux/errno.h> 33 #include <linux/init.h> 34 #include <linux/interrupt.h> 35 #include <linux/ioport.h> 36 #include <linux/major.h> 37 #include <linux/module.h> 38 #include <linux/mm.h> 39 #include <linux/of.h> 40 #include <linux/of_device.h> 41 #include <linux/platform_device.h> 42 #include <linux/pm_runtime.h> 43 #include <linux/scatterlist.h> 44 #include <linux/serial.h> 45 #include <linux/serial_sci.h> 46 #include <linux/sh_dma.h> 47 #include <linux/slab.h> 48 #include <linux/string.h> 49 #include <linux/sysrq.h> 50 #include <linux/timer.h> 51 #include <linux/tty.h> 52 #include <linux/tty_flip.h> 53 54 #ifdef CONFIG_SUPERH 55 #include <asm/sh_bios.h> 56 #endif 57 58 #include "serial_mctrl_gpio.h" 59 #include "sh-sci.h" 60 61 /* Offsets into the sci_port->irqs array */ 62 enum { 63 SCIx_ERI_IRQ, 64 SCIx_RXI_IRQ, 65 SCIx_TXI_IRQ, 66 SCIx_BRI_IRQ, 67 SCIx_NR_IRQS, 68 69 SCIx_MUX_IRQ = SCIx_NR_IRQS, /* special case */ 70 }; 71 72 #define SCIx_IRQ_IS_MUXED(port) \ 73 ((port)->irqs[SCIx_ERI_IRQ] == \ 74 (port)->irqs[SCIx_RXI_IRQ]) || \ 75 ((port)->irqs[SCIx_ERI_IRQ] && \ 76 ((port)->irqs[SCIx_RXI_IRQ] < 0)) 77 78 enum SCI_CLKS { 79 SCI_FCK, /* Functional Clock */ 80 SCI_SCK, /* Optional External Clock */ 81 SCI_BRG_INT, /* Optional BRG Internal Clock Source */ 82 SCI_SCIF_CLK, /* Optional BRG External Clock Source */ 83 SCI_NUM_CLKS 84 }; 85 86 /* Bit x set means sampling rate x + 1 is supported */ 87 #define SCI_SR(x) BIT((x) - 1) 88 #define SCI_SR_RANGE(x, y) GENMASK((y) - 1, (x) - 1) 89 90 #define SCI_SR_SCIFAB SCI_SR(5) | SCI_SR(7) | SCI_SR(11) | \ 91 SCI_SR(13) | SCI_SR(16) | SCI_SR(17) | \ 92 SCI_SR(19) | SCI_SR(27) 93 94 #define min_sr(_port) ffs((_port)->sampling_rate_mask) 95 #define max_sr(_port) fls((_port)->sampling_rate_mask) 96 97 /* Iterate over all supported sampling rates, from high to low */ 98 #define for_each_sr(_sr, _port) \ 99 for ((_sr) = max_sr(_port); (_sr) >= min_sr(_port); (_sr)--) \ 100 if ((_port)->sampling_rate_mask & SCI_SR((_sr))) 101 102 struct plat_sci_reg { 103 u8 offset, size; 104 }; 105 106 struct sci_port_params { 107 const struct plat_sci_reg regs[SCIx_NR_REGS]; 108 unsigned int fifosize; 109 unsigned int overrun_reg; 110 unsigned int overrun_mask; 111 unsigned int sampling_rate_mask; 112 unsigned int error_mask; 113 unsigned int error_clear; 114 }; 115 116 struct sci_port { 117 struct uart_port port; 118 119 /* Platform configuration */ 120 const struct sci_port_params *params; 121 const struct plat_sci_port *cfg; 122 unsigned int sampling_rate_mask; 123 resource_size_t reg_size; 124 struct mctrl_gpios *gpios; 125 126 /* Clocks */ 127 struct clk *clks[SCI_NUM_CLKS]; 128 unsigned long clk_rates[SCI_NUM_CLKS]; 129 130 int irqs[SCIx_NR_IRQS]; 131 char *irqstr[SCIx_NR_IRQS]; 132 133 struct dma_chan *chan_tx; 134 struct dma_chan *chan_rx; 135 136 #ifdef CONFIG_SERIAL_SH_SCI_DMA 137 dma_cookie_t cookie_tx; 138 dma_cookie_t cookie_rx[2]; 139 dma_cookie_t active_rx; 140 dma_addr_t tx_dma_addr; 141 unsigned int tx_dma_len; 142 struct scatterlist sg_rx[2]; 143 void *rx_buf[2]; 144 size_t buf_len_rx; 145 struct work_struct work_tx; 146 struct timer_list rx_timer; 147 unsigned int rx_timeout; 148 #endif 149 unsigned int rx_frame; 150 int rx_trigger; 151 struct timer_list rx_fifo_timer; 152 int rx_fifo_timeout; 153 u16 hscif_tot; 154 155 bool has_rtscts; 156 bool autorts; 157 }; 158 159 #define SCI_NPORTS CONFIG_SERIAL_SH_SCI_NR_UARTS 160 161 static struct sci_port sci_ports[SCI_NPORTS]; 162 static struct uart_driver sci_uart_driver; 163 164 static inline struct sci_port * 165 to_sci_port(struct uart_port *uart) 166 { 167 return container_of(uart, struct sci_port, port); 168 } 169 170 static const struct sci_port_params sci_port_params[SCIx_NR_REGTYPES] = { 171 /* 172 * Common SCI definitions, dependent on the port's regshift 173 * value. 174 */ 175 [SCIx_SCI_REGTYPE] = { 176 .regs = { 177 [SCSMR] = { 0x00, 8 }, 178 [SCBRR] = { 0x01, 8 }, 179 [SCSCR] = { 0x02, 8 }, 180 [SCxTDR] = { 0x03, 8 }, 181 [SCxSR] = { 0x04, 8 }, 182 [SCxRDR] = { 0x05, 8 }, 183 }, 184 .fifosize = 1, 185 .overrun_reg = SCxSR, 186 .overrun_mask = SCI_ORER, 187 .sampling_rate_mask = SCI_SR(32), 188 .error_mask = SCI_DEFAULT_ERROR_MASK | SCI_ORER, 189 .error_clear = SCI_ERROR_CLEAR & ~SCI_ORER, 190 }, 191 192 /* 193 * Common definitions for legacy IrDA ports. 194 */ 195 [SCIx_IRDA_REGTYPE] = { 196 .regs = { 197 [SCSMR] = { 0x00, 8 }, 198 [SCBRR] = { 0x02, 8 }, 199 [SCSCR] = { 0x04, 8 }, 200 [SCxTDR] = { 0x06, 8 }, 201 [SCxSR] = { 0x08, 16 }, 202 [SCxRDR] = { 0x0a, 8 }, 203 [SCFCR] = { 0x0c, 8 }, 204 [SCFDR] = { 0x0e, 16 }, 205 }, 206 .fifosize = 1, 207 .overrun_reg = SCxSR, 208 .overrun_mask = SCI_ORER, 209 .sampling_rate_mask = SCI_SR(32), 210 .error_mask = SCI_DEFAULT_ERROR_MASK | SCI_ORER, 211 .error_clear = SCI_ERROR_CLEAR & ~SCI_ORER, 212 }, 213 214 /* 215 * Common SCIFA definitions. 216 */ 217 [SCIx_SCIFA_REGTYPE] = { 218 .regs = { 219 [SCSMR] = { 0x00, 16 }, 220 [SCBRR] = { 0x04, 8 }, 221 [SCSCR] = { 0x08, 16 }, 222 [SCxTDR] = { 0x20, 8 }, 223 [SCxSR] = { 0x14, 16 }, 224 [SCxRDR] = { 0x24, 8 }, 225 [SCFCR] = { 0x18, 16 }, 226 [SCFDR] = { 0x1c, 16 }, 227 [SCPCR] = { 0x30, 16 }, 228 [SCPDR] = { 0x34, 16 }, 229 }, 230 .fifosize = 64, 231 .overrun_reg = SCxSR, 232 .overrun_mask = SCIFA_ORER, 233 .sampling_rate_mask = SCI_SR_SCIFAB, 234 .error_mask = SCIF_DEFAULT_ERROR_MASK | SCIFA_ORER, 235 .error_clear = SCIF_ERROR_CLEAR & ~SCIFA_ORER, 236 }, 237 238 /* 239 * Common SCIFB definitions. 240 */ 241 [SCIx_SCIFB_REGTYPE] = { 242 .regs = { 243 [SCSMR] = { 0x00, 16 }, 244 [SCBRR] = { 0x04, 8 }, 245 [SCSCR] = { 0x08, 16 }, 246 [SCxTDR] = { 0x40, 8 }, 247 [SCxSR] = { 0x14, 16 }, 248 [SCxRDR] = { 0x60, 8 }, 249 [SCFCR] = { 0x18, 16 }, 250 [SCTFDR] = { 0x38, 16 }, 251 [SCRFDR] = { 0x3c, 16 }, 252 [SCPCR] = { 0x30, 16 }, 253 [SCPDR] = { 0x34, 16 }, 254 }, 255 .fifosize = 256, 256 .overrun_reg = SCxSR, 257 .overrun_mask = SCIFA_ORER, 258 .sampling_rate_mask = SCI_SR_SCIFAB, 259 .error_mask = SCIF_DEFAULT_ERROR_MASK | SCIFA_ORER, 260 .error_clear = SCIF_ERROR_CLEAR & ~SCIFA_ORER, 261 }, 262 263 /* 264 * Common SH-2(A) SCIF definitions for ports with FIFO data 265 * count registers. 266 */ 267 [SCIx_SH2_SCIF_FIFODATA_REGTYPE] = { 268 .regs = { 269 [SCSMR] = { 0x00, 16 }, 270 [SCBRR] = { 0x04, 8 }, 271 [SCSCR] = { 0x08, 16 }, 272 [SCxTDR] = { 0x0c, 8 }, 273 [SCxSR] = { 0x10, 16 }, 274 [SCxRDR] = { 0x14, 8 }, 275 [SCFCR] = { 0x18, 16 }, 276 [SCFDR] = { 0x1c, 16 }, 277 [SCSPTR] = { 0x20, 16 }, 278 [SCLSR] = { 0x24, 16 }, 279 }, 280 .fifosize = 16, 281 .overrun_reg = SCLSR, 282 .overrun_mask = SCLSR_ORER, 283 .sampling_rate_mask = SCI_SR(32), 284 .error_mask = SCIF_DEFAULT_ERROR_MASK, 285 .error_clear = SCIF_ERROR_CLEAR, 286 }, 287 288 /* 289 * Common SH-3 SCIF definitions. 290 */ 291 [SCIx_SH3_SCIF_REGTYPE] = { 292 .regs = { 293 [SCSMR] = { 0x00, 8 }, 294 [SCBRR] = { 0x02, 8 }, 295 [SCSCR] = { 0x04, 8 }, 296 [SCxTDR] = { 0x06, 8 }, 297 [SCxSR] = { 0x08, 16 }, 298 [SCxRDR] = { 0x0a, 8 }, 299 [SCFCR] = { 0x0c, 8 }, 300 [SCFDR] = { 0x0e, 16 }, 301 }, 302 .fifosize = 16, 303 .overrun_reg = SCLSR, 304 .overrun_mask = SCLSR_ORER, 305 .sampling_rate_mask = SCI_SR(32), 306 .error_mask = SCIF_DEFAULT_ERROR_MASK, 307 .error_clear = SCIF_ERROR_CLEAR, 308 }, 309 310 /* 311 * Common SH-4(A) SCIF(B) definitions. 312 */ 313 [SCIx_SH4_SCIF_REGTYPE] = { 314 .regs = { 315 [SCSMR] = { 0x00, 16 }, 316 [SCBRR] = { 0x04, 8 }, 317 [SCSCR] = { 0x08, 16 }, 318 [SCxTDR] = { 0x0c, 8 }, 319 [SCxSR] = { 0x10, 16 }, 320 [SCxRDR] = { 0x14, 8 }, 321 [SCFCR] = { 0x18, 16 }, 322 [SCFDR] = { 0x1c, 16 }, 323 [SCSPTR] = { 0x20, 16 }, 324 [SCLSR] = { 0x24, 16 }, 325 }, 326 .fifosize = 16, 327 .overrun_reg = SCLSR, 328 .overrun_mask = SCLSR_ORER, 329 .sampling_rate_mask = SCI_SR(32), 330 .error_mask = SCIF_DEFAULT_ERROR_MASK, 331 .error_clear = SCIF_ERROR_CLEAR, 332 }, 333 334 /* 335 * Common SCIF definitions for ports with a Baud Rate Generator for 336 * External Clock (BRG). 337 */ 338 [SCIx_SH4_SCIF_BRG_REGTYPE] = { 339 .regs = { 340 [SCSMR] = { 0x00, 16 }, 341 [SCBRR] = { 0x04, 8 }, 342 [SCSCR] = { 0x08, 16 }, 343 [SCxTDR] = { 0x0c, 8 }, 344 [SCxSR] = { 0x10, 16 }, 345 [SCxRDR] = { 0x14, 8 }, 346 [SCFCR] = { 0x18, 16 }, 347 [SCFDR] = { 0x1c, 16 }, 348 [SCSPTR] = { 0x20, 16 }, 349 [SCLSR] = { 0x24, 16 }, 350 [SCDL] = { 0x30, 16 }, 351 [SCCKS] = { 0x34, 16 }, 352 }, 353 .fifosize = 16, 354 .overrun_reg = SCLSR, 355 .overrun_mask = SCLSR_ORER, 356 .sampling_rate_mask = SCI_SR(32), 357 .error_mask = SCIF_DEFAULT_ERROR_MASK, 358 .error_clear = SCIF_ERROR_CLEAR, 359 }, 360 361 /* 362 * Common HSCIF definitions. 363 */ 364 [SCIx_HSCIF_REGTYPE] = { 365 .regs = { 366 [SCSMR] = { 0x00, 16 }, 367 [SCBRR] = { 0x04, 8 }, 368 [SCSCR] = { 0x08, 16 }, 369 [SCxTDR] = { 0x0c, 8 }, 370 [SCxSR] = { 0x10, 16 }, 371 [SCxRDR] = { 0x14, 8 }, 372 [SCFCR] = { 0x18, 16 }, 373 [SCFDR] = { 0x1c, 16 }, 374 [SCSPTR] = { 0x20, 16 }, 375 [SCLSR] = { 0x24, 16 }, 376 [HSSRR] = { 0x40, 16 }, 377 [SCDL] = { 0x30, 16 }, 378 [SCCKS] = { 0x34, 16 }, 379 [HSRTRGR] = { 0x54, 16 }, 380 [HSTTRGR] = { 0x58, 16 }, 381 }, 382 .fifosize = 128, 383 .overrun_reg = SCLSR, 384 .overrun_mask = SCLSR_ORER, 385 .sampling_rate_mask = SCI_SR_RANGE(8, 32), 386 .error_mask = SCIF_DEFAULT_ERROR_MASK, 387 .error_clear = SCIF_ERROR_CLEAR, 388 }, 389 390 /* 391 * Common SH-4(A) SCIF(B) definitions for ports without an SCSPTR 392 * register. 393 */ 394 [SCIx_SH4_SCIF_NO_SCSPTR_REGTYPE] = { 395 .regs = { 396 [SCSMR] = { 0x00, 16 }, 397 [SCBRR] = { 0x04, 8 }, 398 [SCSCR] = { 0x08, 16 }, 399 [SCxTDR] = { 0x0c, 8 }, 400 [SCxSR] = { 0x10, 16 }, 401 [SCxRDR] = { 0x14, 8 }, 402 [SCFCR] = { 0x18, 16 }, 403 [SCFDR] = { 0x1c, 16 }, 404 [SCLSR] = { 0x24, 16 }, 405 }, 406 .fifosize = 16, 407 .overrun_reg = SCLSR, 408 .overrun_mask = SCLSR_ORER, 409 .sampling_rate_mask = SCI_SR(32), 410 .error_mask = SCIF_DEFAULT_ERROR_MASK, 411 .error_clear = SCIF_ERROR_CLEAR, 412 }, 413 414 /* 415 * Common SH-4(A) SCIF(B) definitions for ports with FIFO data 416 * count registers. 417 */ 418 [SCIx_SH4_SCIF_FIFODATA_REGTYPE] = { 419 .regs = { 420 [SCSMR] = { 0x00, 16 }, 421 [SCBRR] = { 0x04, 8 }, 422 [SCSCR] = { 0x08, 16 }, 423 [SCxTDR] = { 0x0c, 8 }, 424 [SCxSR] = { 0x10, 16 }, 425 [SCxRDR] = { 0x14, 8 }, 426 [SCFCR] = { 0x18, 16 }, 427 [SCFDR] = { 0x1c, 16 }, 428 [SCTFDR] = { 0x1c, 16 }, /* aliased to SCFDR */ 429 [SCRFDR] = { 0x20, 16 }, 430 [SCSPTR] = { 0x24, 16 }, 431 [SCLSR] = { 0x28, 16 }, 432 }, 433 .fifosize = 16, 434 .overrun_reg = SCLSR, 435 .overrun_mask = SCLSR_ORER, 436 .sampling_rate_mask = SCI_SR(32), 437 .error_mask = SCIF_DEFAULT_ERROR_MASK, 438 .error_clear = SCIF_ERROR_CLEAR, 439 }, 440 441 /* 442 * SH7705-style SCIF(B) ports, lacking both SCSPTR and SCLSR 443 * registers. 444 */ 445 [SCIx_SH7705_SCIF_REGTYPE] = { 446 .regs = { 447 [SCSMR] = { 0x00, 16 }, 448 [SCBRR] = { 0x04, 8 }, 449 [SCSCR] = { 0x08, 16 }, 450 [SCxTDR] = { 0x20, 8 }, 451 [SCxSR] = { 0x14, 16 }, 452 [SCxRDR] = { 0x24, 8 }, 453 [SCFCR] = { 0x18, 16 }, 454 [SCFDR] = { 0x1c, 16 }, 455 }, 456 .fifosize = 64, 457 .overrun_reg = SCxSR, 458 .overrun_mask = SCIFA_ORER, 459 .sampling_rate_mask = SCI_SR(16), 460 .error_mask = SCIF_DEFAULT_ERROR_MASK | SCIFA_ORER, 461 .error_clear = SCIF_ERROR_CLEAR & ~SCIFA_ORER, 462 }, 463 }; 464 465 #define sci_getreg(up, offset) (&to_sci_port(up)->params->regs[offset]) 466 467 /* 468 * The "offset" here is rather misleading, in that it refers to an enum 469 * value relative to the port mapping rather than the fixed offset 470 * itself, which needs to be manually retrieved from the platform's 471 * register map for the given port. 472 */ 473 static unsigned int sci_serial_in(struct uart_port *p, int offset) 474 { 475 const struct plat_sci_reg *reg = sci_getreg(p, offset); 476 477 if (reg->size == 8) 478 return ioread8(p->membase + (reg->offset << p->regshift)); 479 else if (reg->size == 16) 480 return ioread16(p->membase + (reg->offset << p->regshift)); 481 else 482 WARN(1, "Invalid register access\n"); 483 484 return 0; 485 } 486 487 static void sci_serial_out(struct uart_port *p, int offset, int value) 488 { 489 const struct plat_sci_reg *reg = sci_getreg(p, offset); 490 491 if (reg->size == 8) 492 iowrite8(value, p->membase + (reg->offset << p->regshift)); 493 else if (reg->size == 16) 494 iowrite16(value, p->membase + (reg->offset << p->regshift)); 495 else 496 WARN(1, "Invalid register access\n"); 497 } 498 499 static void sci_port_enable(struct sci_port *sci_port) 500 { 501 unsigned int i; 502 503 if (!sci_port->port.dev) 504 return; 505 506 pm_runtime_get_sync(sci_port->port.dev); 507 508 for (i = 0; i < SCI_NUM_CLKS; i++) { 509 clk_prepare_enable(sci_port->clks[i]); 510 sci_port->clk_rates[i] = clk_get_rate(sci_port->clks[i]); 511 } 512 sci_port->port.uartclk = sci_port->clk_rates[SCI_FCK]; 513 } 514 515 static void sci_port_disable(struct sci_port *sci_port) 516 { 517 unsigned int i; 518 519 if (!sci_port->port.dev) 520 return; 521 522 for (i = SCI_NUM_CLKS; i-- > 0; ) 523 clk_disable_unprepare(sci_port->clks[i]); 524 525 pm_runtime_put_sync(sci_port->port.dev); 526 } 527 528 static inline unsigned long port_rx_irq_mask(struct uart_port *port) 529 { 530 /* 531 * Not all ports (such as SCIFA) will support REIE. Rather than 532 * special-casing the port type, we check the port initialization 533 * IRQ enable mask to see whether the IRQ is desired at all. If 534 * it's unset, it's logically inferred that there's no point in 535 * testing for it. 536 */ 537 return SCSCR_RIE | (to_sci_port(port)->cfg->scscr & SCSCR_REIE); 538 } 539 540 static void sci_start_tx(struct uart_port *port) 541 { 542 struct sci_port *s = to_sci_port(port); 543 unsigned short ctrl; 544 545 #ifdef CONFIG_SERIAL_SH_SCI_DMA 546 if (port->type == PORT_SCIFA || port->type == PORT_SCIFB) { 547 u16 new, scr = serial_port_in(port, SCSCR); 548 if (s->chan_tx) 549 new = scr | SCSCR_TDRQE; 550 else 551 new = scr & ~SCSCR_TDRQE; 552 if (new != scr) 553 serial_port_out(port, SCSCR, new); 554 } 555 556 if (s->chan_tx && !uart_circ_empty(&s->port.state->xmit) && 557 dma_submit_error(s->cookie_tx)) { 558 s->cookie_tx = 0; 559 schedule_work(&s->work_tx); 560 } 561 #endif 562 563 if (!s->chan_tx || port->type == PORT_SCIFA || port->type == PORT_SCIFB) { 564 /* Set TIE (Transmit Interrupt Enable) bit in SCSCR */ 565 ctrl = serial_port_in(port, SCSCR); 566 serial_port_out(port, SCSCR, ctrl | SCSCR_TIE); 567 } 568 } 569 570 static void sci_stop_tx(struct uart_port *port) 571 { 572 unsigned short ctrl; 573 574 /* Clear TIE (Transmit Interrupt Enable) bit in SCSCR */ 575 ctrl = serial_port_in(port, SCSCR); 576 577 if (port->type == PORT_SCIFA || port->type == PORT_SCIFB) 578 ctrl &= ~SCSCR_TDRQE; 579 580 ctrl &= ~SCSCR_TIE; 581 582 serial_port_out(port, SCSCR, ctrl); 583 } 584 585 static void sci_start_rx(struct uart_port *port) 586 { 587 unsigned short ctrl; 588 589 ctrl = serial_port_in(port, SCSCR) | port_rx_irq_mask(port); 590 591 if (port->type == PORT_SCIFA || port->type == PORT_SCIFB) 592 ctrl &= ~SCSCR_RDRQE; 593 594 serial_port_out(port, SCSCR, ctrl); 595 } 596 597 static void sci_stop_rx(struct uart_port *port) 598 { 599 unsigned short ctrl; 600 601 ctrl = serial_port_in(port, SCSCR); 602 603 if (port->type == PORT_SCIFA || port->type == PORT_SCIFB) 604 ctrl &= ~SCSCR_RDRQE; 605 606 ctrl &= ~port_rx_irq_mask(port); 607 608 serial_port_out(port, SCSCR, ctrl); 609 } 610 611 static void sci_clear_SCxSR(struct uart_port *port, unsigned int mask) 612 { 613 if (port->type == PORT_SCI) { 614 /* Just store the mask */ 615 serial_port_out(port, SCxSR, mask); 616 } else if (to_sci_port(port)->params->overrun_mask == SCIFA_ORER) { 617 /* SCIFA/SCIFB and SCIF on SH7705/SH7720/SH7721 */ 618 /* Only clear the status bits we want to clear */ 619 serial_port_out(port, SCxSR, 620 serial_port_in(port, SCxSR) & mask); 621 } else { 622 /* Store the mask, clear parity/framing errors */ 623 serial_port_out(port, SCxSR, mask & ~(SCIF_FERC | SCIF_PERC)); 624 } 625 } 626 627 #if defined(CONFIG_CONSOLE_POLL) || defined(CONFIG_SERIAL_SH_SCI_CONSOLE) || \ 628 defined(CONFIG_SERIAL_SH_SCI_EARLYCON) 629 630 #ifdef CONFIG_CONSOLE_POLL 631 static int sci_poll_get_char(struct uart_port *port) 632 { 633 unsigned short status; 634 int c; 635 636 do { 637 status = serial_port_in(port, SCxSR); 638 if (status & SCxSR_ERRORS(port)) { 639 sci_clear_SCxSR(port, SCxSR_ERROR_CLEAR(port)); 640 continue; 641 } 642 break; 643 } while (1); 644 645 if (!(status & SCxSR_RDxF(port))) 646 return NO_POLL_CHAR; 647 648 c = serial_port_in(port, SCxRDR); 649 650 /* Dummy read */ 651 serial_port_in(port, SCxSR); 652 sci_clear_SCxSR(port, SCxSR_RDxF_CLEAR(port)); 653 654 return c; 655 } 656 #endif 657 658 static void sci_poll_put_char(struct uart_port *port, unsigned char c) 659 { 660 unsigned short status; 661 662 do { 663 status = serial_port_in(port, SCxSR); 664 } while (!(status & SCxSR_TDxE(port))); 665 666 serial_port_out(port, SCxTDR, c); 667 sci_clear_SCxSR(port, SCxSR_TDxE_CLEAR(port) & ~SCxSR_TEND(port)); 668 } 669 #endif /* CONFIG_CONSOLE_POLL || CONFIG_SERIAL_SH_SCI_CONSOLE || 670 CONFIG_SERIAL_SH_SCI_EARLYCON */ 671 672 static void sci_init_pins(struct uart_port *port, unsigned int cflag) 673 { 674 struct sci_port *s = to_sci_port(port); 675 676 /* 677 * Use port-specific handler if provided. 678 */ 679 if (s->cfg->ops && s->cfg->ops->init_pins) { 680 s->cfg->ops->init_pins(port, cflag); 681 return; 682 } 683 684 if (port->type == PORT_SCIFA || port->type == PORT_SCIFB) { 685 u16 data = serial_port_in(port, SCPDR); 686 u16 ctrl = serial_port_in(port, SCPCR); 687 688 /* Enable RXD and TXD pin functions */ 689 ctrl &= ~(SCPCR_RXDC | SCPCR_TXDC); 690 if (to_sci_port(port)->has_rtscts) { 691 /* RTS# is output, active low, unless autorts */ 692 if (!(port->mctrl & TIOCM_RTS)) { 693 ctrl |= SCPCR_RTSC; 694 data |= SCPDR_RTSD; 695 } else if (!s->autorts) { 696 ctrl |= SCPCR_RTSC; 697 data &= ~SCPDR_RTSD; 698 } else { 699 /* Enable RTS# pin function */ 700 ctrl &= ~SCPCR_RTSC; 701 } 702 /* Enable CTS# pin function */ 703 ctrl &= ~SCPCR_CTSC; 704 } 705 serial_port_out(port, SCPDR, data); 706 serial_port_out(port, SCPCR, ctrl); 707 } else if (sci_getreg(port, SCSPTR)->size) { 708 u16 status = serial_port_in(port, SCSPTR); 709 710 /* RTS# is always output; and active low, unless autorts */ 711 status |= SCSPTR_RTSIO; 712 if (!(port->mctrl & TIOCM_RTS)) 713 status |= SCSPTR_RTSDT; 714 else if (!s->autorts) 715 status &= ~SCSPTR_RTSDT; 716 /* CTS# and SCK are inputs */ 717 status &= ~(SCSPTR_CTSIO | SCSPTR_SCKIO); 718 serial_port_out(port, SCSPTR, status); 719 } 720 } 721 722 static int sci_txfill(struct uart_port *port) 723 { 724 struct sci_port *s = to_sci_port(port); 725 unsigned int fifo_mask = (s->params->fifosize << 1) - 1; 726 const struct plat_sci_reg *reg; 727 728 reg = sci_getreg(port, SCTFDR); 729 if (reg->size) 730 return serial_port_in(port, SCTFDR) & fifo_mask; 731 732 reg = sci_getreg(port, SCFDR); 733 if (reg->size) 734 return serial_port_in(port, SCFDR) >> 8; 735 736 return !(serial_port_in(port, SCxSR) & SCI_TDRE); 737 } 738 739 static int sci_txroom(struct uart_port *port) 740 { 741 return port->fifosize - sci_txfill(port); 742 } 743 744 static int sci_rxfill(struct uart_port *port) 745 { 746 struct sci_port *s = to_sci_port(port); 747 unsigned int fifo_mask = (s->params->fifosize << 1) - 1; 748 const struct plat_sci_reg *reg; 749 750 reg = sci_getreg(port, SCRFDR); 751 if (reg->size) 752 return serial_port_in(port, SCRFDR) & fifo_mask; 753 754 reg = sci_getreg(port, SCFDR); 755 if (reg->size) 756 return serial_port_in(port, SCFDR) & fifo_mask; 757 758 return (serial_port_in(port, SCxSR) & SCxSR_RDxF(port)) != 0; 759 } 760 761 /* ********************************************************************** * 762 * the interrupt related routines * 763 * ********************************************************************** */ 764 765 static void sci_transmit_chars(struct uart_port *port) 766 { 767 struct circ_buf *xmit = &port->state->xmit; 768 unsigned int stopped = uart_tx_stopped(port); 769 unsigned short status; 770 unsigned short ctrl; 771 int count; 772 773 status = serial_port_in(port, SCxSR); 774 if (!(status & SCxSR_TDxE(port))) { 775 ctrl = serial_port_in(port, SCSCR); 776 if (uart_circ_empty(xmit)) 777 ctrl &= ~SCSCR_TIE; 778 else 779 ctrl |= SCSCR_TIE; 780 serial_port_out(port, SCSCR, ctrl); 781 return; 782 } 783 784 count = sci_txroom(port); 785 786 do { 787 unsigned char c; 788 789 if (port->x_char) { 790 c = port->x_char; 791 port->x_char = 0; 792 } else if (!uart_circ_empty(xmit) && !stopped) { 793 c = xmit->buf[xmit->tail]; 794 xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1); 795 } else { 796 break; 797 } 798 799 serial_port_out(port, SCxTDR, c); 800 801 port->icount.tx++; 802 } while (--count > 0); 803 804 sci_clear_SCxSR(port, SCxSR_TDxE_CLEAR(port)); 805 806 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) 807 uart_write_wakeup(port); 808 if (uart_circ_empty(xmit)) { 809 sci_stop_tx(port); 810 } else { 811 ctrl = serial_port_in(port, SCSCR); 812 813 if (port->type != PORT_SCI) { 814 serial_port_in(port, SCxSR); /* Dummy read */ 815 sci_clear_SCxSR(port, SCxSR_TDxE_CLEAR(port)); 816 } 817 818 ctrl |= SCSCR_TIE; 819 serial_port_out(port, SCSCR, ctrl); 820 } 821 } 822 823 /* On SH3, SCIF may read end-of-break as a space->mark char */ 824 #define STEPFN(c) ({int __c = (c); (((__c-1)|(__c)) == -1); }) 825 826 static void sci_receive_chars(struct uart_port *port) 827 { 828 struct tty_port *tport = &port->state->port; 829 int i, count, copied = 0; 830 unsigned short status; 831 unsigned char flag; 832 833 status = serial_port_in(port, SCxSR); 834 if (!(status & SCxSR_RDxF(port))) 835 return; 836 837 while (1) { 838 /* Don't copy more bytes than there is room for in the buffer */ 839 count = tty_buffer_request_room(tport, sci_rxfill(port)); 840 841 /* If for any reason we can't copy more data, we're done! */ 842 if (count == 0) 843 break; 844 845 if (port->type == PORT_SCI) { 846 char c = serial_port_in(port, SCxRDR); 847 if (uart_handle_sysrq_char(port, c)) 848 count = 0; 849 else 850 tty_insert_flip_char(tport, c, TTY_NORMAL); 851 } else { 852 for (i = 0; i < count; i++) { 853 char c = serial_port_in(port, SCxRDR); 854 855 status = serial_port_in(port, SCxSR); 856 if (uart_handle_sysrq_char(port, c)) { 857 count--; i--; 858 continue; 859 } 860 861 /* Store data and status */ 862 if (status & SCxSR_FER(port)) { 863 flag = TTY_FRAME; 864 port->icount.frame++; 865 dev_notice(port->dev, "frame error\n"); 866 } else if (status & SCxSR_PER(port)) { 867 flag = TTY_PARITY; 868 port->icount.parity++; 869 dev_notice(port->dev, "parity error\n"); 870 } else 871 flag = TTY_NORMAL; 872 873 tty_insert_flip_char(tport, c, flag); 874 } 875 } 876 877 serial_port_in(port, SCxSR); /* dummy read */ 878 sci_clear_SCxSR(port, SCxSR_RDxF_CLEAR(port)); 879 880 copied += count; 881 port->icount.rx += count; 882 } 883 884 if (copied) { 885 /* Tell the rest of the system the news. New characters! */ 886 tty_flip_buffer_push(tport); 887 } else { 888 serial_port_in(port, SCxSR); /* dummy read */ 889 sci_clear_SCxSR(port, SCxSR_RDxF_CLEAR(port)); 890 } 891 } 892 893 static int sci_handle_errors(struct uart_port *port) 894 { 895 int copied = 0; 896 unsigned short status = serial_port_in(port, SCxSR); 897 struct tty_port *tport = &port->state->port; 898 struct sci_port *s = to_sci_port(port); 899 900 /* Handle overruns */ 901 if (status & s->params->overrun_mask) { 902 port->icount.overrun++; 903 904 /* overrun error */ 905 if (tty_insert_flip_char(tport, 0, TTY_OVERRUN)) 906 copied++; 907 908 dev_notice(port->dev, "overrun error\n"); 909 } 910 911 if (status & SCxSR_FER(port)) { 912 /* frame error */ 913 port->icount.frame++; 914 915 if (tty_insert_flip_char(tport, 0, TTY_FRAME)) 916 copied++; 917 918 dev_notice(port->dev, "frame error\n"); 919 } 920 921 if (status & SCxSR_PER(port)) { 922 /* parity error */ 923 port->icount.parity++; 924 925 if (tty_insert_flip_char(tport, 0, TTY_PARITY)) 926 copied++; 927 928 dev_notice(port->dev, "parity error\n"); 929 } 930 931 if (copied) 932 tty_flip_buffer_push(tport); 933 934 return copied; 935 } 936 937 static int sci_handle_fifo_overrun(struct uart_port *port) 938 { 939 struct tty_port *tport = &port->state->port; 940 struct sci_port *s = to_sci_port(port); 941 const struct plat_sci_reg *reg; 942 int copied = 0; 943 u16 status; 944 945 reg = sci_getreg(port, s->params->overrun_reg); 946 if (!reg->size) 947 return 0; 948 949 status = serial_port_in(port, s->params->overrun_reg); 950 if (status & s->params->overrun_mask) { 951 status &= ~s->params->overrun_mask; 952 serial_port_out(port, s->params->overrun_reg, status); 953 954 port->icount.overrun++; 955 956 tty_insert_flip_char(tport, 0, TTY_OVERRUN); 957 tty_flip_buffer_push(tport); 958 959 dev_dbg(port->dev, "overrun error\n"); 960 copied++; 961 } 962 963 return copied; 964 } 965 966 static int sci_handle_breaks(struct uart_port *port) 967 { 968 int copied = 0; 969 unsigned short status = serial_port_in(port, SCxSR); 970 struct tty_port *tport = &port->state->port; 971 972 if (uart_handle_break(port)) 973 return 0; 974 975 if (status & SCxSR_BRK(port)) { 976 port->icount.brk++; 977 978 /* Notify of BREAK */ 979 if (tty_insert_flip_char(tport, 0, TTY_BREAK)) 980 copied++; 981 982 dev_dbg(port->dev, "BREAK detected\n"); 983 } 984 985 if (copied) 986 tty_flip_buffer_push(tport); 987 988 copied += sci_handle_fifo_overrun(port); 989 990 return copied; 991 } 992 993 static int scif_set_rtrg(struct uart_port *port, int rx_trig) 994 { 995 unsigned int bits; 996 997 if (rx_trig < 1) 998 rx_trig = 1; 999 if (rx_trig >= port->fifosize) 1000 rx_trig = port->fifosize; 1001 1002 /* HSCIF can be set to an arbitrary level. */ 1003 if (sci_getreg(port, HSRTRGR)->size) { 1004 serial_port_out(port, HSRTRGR, rx_trig); 1005 return rx_trig; 1006 } 1007 1008 switch (port->type) { 1009 case PORT_SCIF: 1010 if (rx_trig < 4) { 1011 bits = 0; 1012 rx_trig = 1; 1013 } else if (rx_trig < 8) { 1014 bits = SCFCR_RTRG0; 1015 rx_trig = 4; 1016 } else if (rx_trig < 14) { 1017 bits = SCFCR_RTRG1; 1018 rx_trig = 8; 1019 } else { 1020 bits = SCFCR_RTRG0 | SCFCR_RTRG1; 1021 rx_trig = 14; 1022 } 1023 break; 1024 case PORT_SCIFA: 1025 case PORT_SCIFB: 1026 if (rx_trig < 16) { 1027 bits = 0; 1028 rx_trig = 1; 1029 } else if (rx_trig < 32) { 1030 bits = SCFCR_RTRG0; 1031 rx_trig = 16; 1032 } else if (rx_trig < 48) { 1033 bits = SCFCR_RTRG1; 1034 rx_trig = 32; 1035 } else { 1036 bits = SCFCR_RTRG0 | SCFCR_RTRG1; 1037 rx_trig = 48; 1038 } 1039 break; 1040 default: 1041 WARN(1, "unknown FIFO configuration"); 1042 return 1; 1043 } 1044 1045 serial_port_out(port, SCFCR, 1046 (serial_port_in(port, SCFCR) & 1047 ~(SCFCR_RTRG1 | SCFCR_RTRG0)) | bits); 1048 1049 return rx_trig; 1050 } 1051 1052 static int scif_rtrg_enabled(struct uart_port *port) 1053 { 1054 if (sci_getreg(port, HSRTRGR)->size) 1055 return serial_port_in(port, HSRTRGR) != 0; 1056 else 1057 return (serial_port_in(port, SCFCR) & 1058 (SCFCR_RTRG0 | SCFCR_RTRG1)) != 0; 1059 } 1060 1061 static void rx_fifo_timer_fn(struct timer_list *t) 1062 { 1063 struct sci_port *s = from_timer(s, t, rx_fifo_timer); 1064 struct uart_port *port = &s->port; 1065 1066 dev_dbg(port->dev, "Rx timed out\n"); 1067 scif_set_rtrg(port, 1); 1068 } 1069 1070 static ssize_t rx_trigger_show(struct device *dev, 1071 struct device_attribute *attr, 1072 char *buf) 1073 { 1074 struct uart_port *port = dev_get_drvdata(dev); 1075 struct sci_port *sci = to_sci_port(port); 1076 1077 return sprintf(buf, "%d\n", sci->rx_trigger); 1078 } 1079 1080 static ssize_t rx_trigger_store(struct device *dev, 1081 struct device_attribute *attr, 1082 const char *buf, 1083 size_t count) 1084 { 1085 struct uart_port *port = dev_get_drvdata(dev); 1086 struct sci_port *sci = to_sci_port(port); 1087 int ret; 1088 long r; 1089 1090 ret = kstrtol(buf, 0, &r); 1091 if (ret) 1092 return ret; 1093 1094 sci->rx_trigger = scif_set_rtrg(port, r); 1095 if (port->type == PORT_SCIFA || port->type == PORT_SCIFB) 1096 scif_set_rtrg(port, 1); 1097 1098 return count; 1099 } 1100 1101 static DEVICE_ATTR(rx_fifo_trigger, 0644, rx_trigger_show, rx_trigger_store); 1102 1103 static ssize_t rx_fifo_timeout_show(struct device *dev, 1104 struct device_attribute *attr, 1105 char *buf) 1106 { 1107 struct uart_port *port = dev_get_drvdata(dev); 1108 struct sci_port *sci = to_sci_port(port); 1109 int v; 1110 1111 if (port->type == PORT_HSCIF) 1112 v = sci->hscif_tot >> HSSCR_TOT_SHIFT; 1113 else 1114 v = sci->rx_fifo_timeout; 1115 1116 return sprintf(buf, "%d\n", v); 1117 } 1118 1119 static ssize_t rx_fifo_timeout_store(struct device *dev, 1120 struct device_attribute *attr, 1121 const char *buf, 1122 size_t count) 1123 { 1124 struct uart_port *port = dev_get_drvdata(dev); 1125 struct sci_port *sci = to_sci_port(port); 1126 int ret; 1127 long r; 1128 1129 ret = kstrtol(buf, 0, &r); 1130 if (ret) 1131 return ret; 1132 1133 if (port->type == PORT_HSCIF) { 1134 if (r < 0 || r > 3) 1135 return -EINVAL; 1136 sci->hscif_tot = r << HSSCR_TOT_SHIFT; 1137 } else { 1138 sci->rx_fifo_timeout = r; 1139 scif_set_rtrg(port, 1); 1140 if (r > 0) 1141 timer_setup(&sci->rx_fifo_timer, rx_fifo_timer_fn, 0); 1142 } 1143 1144 return count; 1145 } 1146 1147 static DEVICE_ATTR_RW(rx_fifo_timeout); 1148 1149 1150 #ifdef CONFIG_SERIAL_SH_SCI_DMA 1151 static void sci_dma_tx_complete(void *arg) 1152 { 1153 struct sci_port *s = arg; 1154 struct uart_port *port = &s->port; 1155 struct circ_buf *xmit = &port->state->xmit; 1156 unsigned long flags; 1157 1158 dev_dbg(port->dev, "%s(%d)\n", __func__, port->line); 1159 1160 spin_lock_irqsave(&port->lock, flags); 1161 1162 xmit->tail += s->tx_dma_len; 1163 xmit->tail &= UART_XMIT_SIZE - 1; 1164 1165 port->icount.tx += s->tx_dma_len; 1166 1167 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) 1168 uart_write_wakeup(port); 1169 1170 if (!uart_circ_empty(xmit)) { 1171 s->cookie_tx = 0; 1172 schedule_work(&s->work_tx); 1173 } else { 1174 s->cookie_tx = -EINVAL; 1175 if (port->type == PORT_SCIFA || port->type == PORT_SCIFB) { 1176 u16 ctrl = serial_port_in(port, SCSCR); 1177 serial_port_out(port, SCSCR, ctrl & ~SCSCR_TIE); 1178 } 1179 } 1180 1181 spin_unlock_irqrestore(&port->lock, flags); 1182 } 1183 1184 /* Locking: called with port lock held */ 1185 static int sci_dma_rx_push(struct sci_port *s, void *buf, size_t count) 1186 { 1187 struct uart_port *port = &s->port; 1188 struct tty_port *tport = &port->state->port; 1189 int copied; 1190 1191 copied = tty_insert_flip_string(tport, buf, count); 1192 if (copied < count) 1193 port->icount.buf_overrun++; 1194 1195 port->icount.rx += copied; 1196 1197 return copied; 1198 } 1199 1200 static int sci_dma_rx_find_active(struct sci_port *s) 1201 { 1202 unsigned int i; 1203 1204 for (i = 0; i < ARRAY_SIZE(s->cookie_rx); i++) 1205 if (s->active_rx == s->cookie_rx[i]) 1206 return i; 1207 1208 return -1; 1209 } 1210 1211 static void sci_rx_dma_release(struct sci_port *s, bool enable_pio) 1212 { 1213 struct dma_chan *chan = s->chan_rx; 1214 struct uart_port *port = &s->port; 1215 unsigned long flags; 1216 1217 spin_lock_irqsave(&port->lock, flags); 1218 s->chan_rx = NULL; 1219 s->cookie_rx[0] = s->cookie_rx[1] = -EINVAL; 1220 spin_unlock_irqrestore(&port->lock, flags); 1221 dmaengine_terminate_all(chan); 1222 dma_free_coherent(chan->device->dev, s->buf_len_rx * 2, s->rx_buf[0], 1223 sg_dma_address(&s->sg_rx[0])); 1224 dma_release_channel(chan); 1225 if (enable_pio) { 1226 spin_lock_irqsave(&port->lock, flags); 1227 sci_start_rx(port); 1228 spin_unlock_irqrestore(&port->lock, flags); 1229 } 1230 } 1231 1232 static void sci_dma_rx_complete(void *arg) 1233 { 1234 struct sci_port *s = arg; 1235 struct dma_chan *chan = s->chan_rx; 1236 struct uart_port *port = &s->port; 1237 struct dma_async_tx_descriptor *desc; 1238 unsigned long flags; 1239 int active, count = 0; 1240 1241 dev_dbg(port->dev, "%s(%d) active cookie %d\n", __func__, port->line, 1242 s->active_rx); 1243 1244 spin_lock_irqsave(&port->lock, flags); 1245 1246 active = sci_dma_rx_find_active(s); 1247 if (active >= 0) 1248 count = sci_dma_rx_push(s, s->rx_buf[active], s->buf_len_rx); 1249 1250 mod_timer(&s->rx_timer, jiffies + s->rx_timeout); 1251 1252 if (count) 1253 tty_flip_buffer_push(&port->state->port); 1254 1255 desc = dmaengine_prep_slave_sg(s->chan_rx, &s->sg_rx[active], 1, 1256 DMA_DEV_TO_MEM, 1257 DMA_PREP_INTERRUPT | DMA_CTRL_ACK); 1258 if (!desc) 1259 goto fail; 1260 1261 desc->callback = sci_dma_rx_complete; 1262 desc->callback_param = s; 1263 s->cookie_rx[active] = dmaengine_submit(desc); 1264 if (dma_submit_error(s->cookie_rx[active])) 1265 goto fail; 1266 1267 s->active_rx = s->cookie_rx[!active]; 1268 1269 dma_async_issue_pending(chan); 1270 1271 spin_unlock_irqrestore(&port->lock, flags); 1272 dev_dbg(port->dev, "%s: cookie %d #%d, new active cookie %d\n", 1273 __func__, s->cookie_rx[active], active, s->active_rx); 1274 return; 1275 1276 fail: 1277 spin_unlock_irqrestore(&port->lock, flags); 1278 dev_warn(port->dev, "Failed submitting Rx DMA descriptor\n"); 1279 sci_rx_dma_release(s, true); 1280 } 1281 1282 static void sci_tx_dma_release(struct sci_port *s, bool enable_pio) 1283 { 1284 struct dma_chan *chan = s->chan_tx; 1285 struct uart_port *port = &s->port; 1286 unsigned long flags; 1287 1288 spin_lock_irqsave(&port->lock, flags); 1289 s->chan_tx = NULL; 1290 s->cookie_tx = -EINVAL; 1291 spin_unlock_irqrestore(&port->lock, flags); 1292 dmaengine_terminate_all(chan); 1293 dma_unmap_single(chan->device->dev, s->tx_dma_addr, UART_XMIT_SIZE, 1294 DMA_TO_DEVICE); 1295 dma_release_channel(chan); 1296 if (enable_pio) { 1297 spin_lock_irqsave(&port->lock, flags); 1298 sci_start_tx(port); 1299 spin_unlock_irqrestore(&port->lock, flags); 1300 } 1301 } 1302 1303 static void sci_submit_rx(struct sci_port *s) 1304 { 1305 struct dma_chan *chan = s->chan_rx; 1306 int i; 1307 1308 for (i = 0; i < 2; i++) { 1309 struct scatterlist *sg = &s->sg_rx[i]; 1310 struct dma_async_tx_descriptor *desc; 1311 1312 desc = dmaengine_prep_slave_sg(chan, 1313 sg, 1, DMA_DEV_TO_MEM, 1314 DMA_PREP_INTERRUPT | DMA_CTRL_ACK); 1315 if (!desc) 1316 goto fail; 1317 1318 desc->callback = sci_dma_rx_complete; 1319 desc->callback_param = s; 1320 s->cookie_rx[i] = dmaengine_submit(desc); 1321 if (dma_submit_error(s->cookie_rx[i])) 1322 goto fail; 1323 1324 } 1325 1326 s->active_rx = s->cookie_rx[0]; 1327 1328 dma_async_issue_pending(chan); 1329 return; 1330 1331 fail: 1332 if (i) 1333 dmaengine_terminate_all(chan); 1334 for (i = 0; i < 2; i++) 1335 s->cookie_rx[i] = -EINVAL; 1336 s->active_rx = -EINVAL; 1337 sci_rx_dma_release(s, true); 1338 } 1339 1340 static void work_fn_tx(struct work_struct *work) 1341 { 1342 struct sci_port *s = container_of(work, struct sci_port, work_tx); 1343 struct dma_async_tx_descriptor *desc; 1344 struct dma_chan *chan = s->chan_tx; 1345 struct uart_port *port = &s->port; 1346 struct circ_buf *xmit = &port->state->xmit; 1347 dma_addr_t buf; 1348 1349 /* 1350 * DMA is idle now. 1351 * Port xmit buffer is already mapped, and it is one page... Just adjust 1352 * offsets and lengths. Since it is a circular buffer, we have to 1353 * transmit till the end, and then the rest. Take the port lock to get a 1354 * consistent xmit buffer state. 1355 */ 1356 spin_lock_irq(&port->lock); 1357 buf = s->tx_dma_addr + (xmit->tail & (UART_XMIT_SIZE - 1)); 1358 s->tx_dma_len = min_t(unsigned int, 1359 CIRC_CNT(xmit->head, xmit->tail, UART_XMIT_SIZE), 1360 CIRC_CNT_TO_END(xmit->head, xmit->tail, UART_XMIT_SIZE)); 1361 spin_unlock_irq(&port->lock); 1362 1363 desc = dmaengine_prep_slave_single(chan, buf, s->tx_dma_len, 1364 DMA_MEM_TO_DEV, 1365 DMA_PREP_INTERRUPT | DMA_CTRL_ACK); 1366 if (!desc) { 1367 dev_warn(port->dev, "Failed preparing Tx DMA descriptor\n"); 1368 /* switch to PIO */ 1369 sci_tx_dma_release(s, true); 1370 return; 1371 } 1372 1373 dma_sync_single_for_device(chan->device->dev, buf, s->tx_dma_len, 1374 DMA_TO_DEVICE); 1375 1376 spin_lock_irq(&port->lock); 1377 desc->callback = sci_dma_tx_complete; 1378 desc->callback_param = s; 1379 spin_unlock_irq(&port->lock); 1380 s->cookie_tx = dmaengine_submit(desc); 1381 if (dma_submit_error(s->cookie_tx)) { 1382 dev_warn(port->dev, "Failed submitting Tx DMA descriptor\n"); 1383 /* switch to PIO */ 1384 sci_tx_dma_release(s, true); 1385 return; 1386 } 1387 1388 dev_dbg(port->dev, "%s: %p: %d...%d, cookie %d\n", 1389 __func__, xmit->buf, xmit->tail, xmit->head, s->cookie_tx); 1390 1391 dma_async_issue_pending(chan); 1392 } 1393 1394 static void rx_timer_fn(struct timer_list *t) 1395 { 1396 struct sci_port *s = from_timer(s, t, rx_timer); 1397 struct dma_chan *chan = s->chan_rx; 1398 struct uart_port *port = &s->port; 1399 struct dma_tx_state state; 1400 enum dma_status status; 1401 unsigned long flags; 1402 unsigned int read; 1403 int active, count; 1404 u16 scr; 1405 1406 dev_dbg(port->dev, "DMA Rx timed out\n"); 1407 1408 spin_lock_irqsave(&port->lock, flags); 1409 1410 active = sci_dma_rx_find_active(s); 1411 if (active < 0) { 1412 spin_unlock_irqrestore(&port->lock, flags); 1413 return; 1414 } 1415 1416 status = dmaengine_tx_status(s->chan_rx, s->active_rx, &state); 1417 if (status == DMA_COMPLETE) { 1418 spin_unlock_irqrestore(&port->lock, flags); 1419 dev_dbg(port->dev, "Cookie %d #%d has already completed\n", 1420 s->active_rx, active); 1421 1422 /* Let packet complete handler take care of the packet */ 1423 return; 1424 } 1425 1426 dmaengine_pause(chan); 1427 1428 /* 1429 * sometimes DMA transfer doesn't stop even if it is stopped and 1430 * data keeps on coming until transaction is complete so check 1431 * for DMA_COMPLETE again 1432 * Let packet complete handler take care of the packet 1433 */ 1434 status = dmaengine_tx_status(s->chan_rx, s->active_rx, &state); 1435 if (status == DMA_COMPLETE) { 1436 spin_unlock_irqrestore(&port->lock, flags); 1437 dev_dbg(port->dev, "Transaction complete after DMA engine was stopped"); 1438 return; 1439 } 1440 1441 /* Handle incomplete DMA receive */ 1442 dmaengine_terminate_all(s->chan_rx); 1443 read = sg_dma_len(&s->sg_rx[active]) - state.residue; 1444 1445 if (read) { 1446 count = sci_dma_rx_push(s, s->rx_buf[active], read); 1447 if (count) 1448 tty_flip_buffer_push(&port->state->port); 1449 } 1450 1451 if (port->type == PORT_SCIFA || port->type == PORT_SCIFB) 1452 sci_submit_rx(s); 1453 1454 /* Direct new serial port interrupts back to CPU */ 1455 scr = serial_port_in(port, SCSCR); 1456 if (port->type == PORT_SCIFA || port->type == PORT_SCIFB) { 1457 scr &= ~SCSCR_RDRQE; 1458 enable_irq(s->irqs[SCIx_RXI_IRQ]); 1459 } 1460 serial_port_out(port, SCSCR, scr | SCSCR_RIE); 1461 1462 spin_unlock_irqrestore(&port->lock, flags); 1463 } 1464 1465 static struct dma_chan *sci_request_dma_chan(struct uart_port *port, 1466 enum dma_transfer_direction dir) 1467 { 1468 struct dma_chan *chan; 1469 struct dma_slave_config cfg; 1470 int ret; 1471 1472 chan = dma_request_slave_channel(port->dev, 1473 dir == DMA_MEM_TO_DEV ? "tx" : "rx"); 1474 if (!chan) { 1475 dev_warn(port->dev, "dma_request_slave_channel failed\n"); 1476 return NULL; 1477 } 1478 1479 memset(&cfg, 0, sizeof(cfg)); 1480 cfg.direction = dir; 1481 if (dir == DMA_MEM_TO_DEV) { 1482 cfg.dst_addr = port->mapbase + 1483 (sci_getreg(port, SCxTDR)->offset << port->regshift); 1484 cfg.dst_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE; 1485 } else { 1486 cfg.src_addr = port->mapbase + 1487 (sci_getreg(port, SCxRDR)->offset << port->regshift); 1488 cfg.src_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE; 1489 } 1490 1491 ret = dmaengine_slave_config(chan, &cfg); 1492 if (ret) { 1493 dev_warn(port->dev, "dmaengine_slave_config failed %d\n", ret); 1494 dma_release_channel(chan); 1495 return NULL; 1496 } 1497 1498 return chan; 1499 } 1500 1501 static void sci_request_dma(struct uart_port *port) 1502 { 1503 struct sci_port *s = to_sci_port(port); 1504 struct dma_chan *chan; 1505 1506 dev_dbg(port->dev, "%s: port %d\n", __func__, port->line); 1507 1508 if (!port->dev->of_node) 1509 return; 1510 1511 s->cookie_tx = -EINVAL; 1512 1513 /* 1514 * Don't request a dma channel if no channel was specified 1515 * in the device tree. 1516 */ 1517 if (!of_find_property(port->dev->of_node, "dmas", NULL)) 1518 return; 1519 1520 chan = sci_request_dma_chan(port, DMA_MEM_TO_DEV); 1521 dev_dbg(port->dev, "%s: TX: got channel %p\n", __func__, chan); 1522 if (chan) { 1523 s->chan_tx = chan; 1524 /* UART circular tx buffer is an aligned page. */ 1525 s->tx_dma_addr = dma_map_single(chan->device->dev, 1526 port->state->xmit.buf, 1527 UART_XMIT_SIZE, 1528 DMA_TO_DEVICE); 1529 if (dma_mapping_error(chan->device->dev, s->tx_dma_addr)) { 1530 dev_warn(port->dev, "Failed mapping Tx DMA descriptor\n"); 1531 dma_release_channel(chan); 1532 s->chan_tx = NULL; 1533 } else { 1534 dev_dbg(port->dev, "%s: mapped %lu@%p to %pad\n", 1535 __func__, UART_XMIT_SIZE, 1536 port->state->xmit.buf, &s->tx_dma_addr); 1537 } 1538 1539 INIT_WORK(&s->work_tx, work_fn_tx); 1540 } 1541 1542 chan = sci_request_dma_chan(port, DMA_DEV_TO_MEM); 1543 dev_dbg(port->dev, "%s: RX: got channel %p\n", __func__, chan); 1544 if (chan) { 1545 unsigned int i; 1546 dma_addr_t dma; 1547 void *buf; 1548 1549 s->chan_rx = chan; 1550 1551 s->buf_len_rx = 2 * max_t(size_t, 16, port->fifosize); 1552 buf = dma_alloc_coherent(chan->device->dev, s->buf_len_rx * 2, 1553 &dma, GFP_KERNEL); 1554 if (!buf) { 1555 dev_warn(port->dev, 1556 "Failed to allocate Rx dma buffer, using PIO\n"); 1557 dma_release_channel(chan); 1558 s->chan_rx = NULL; 1559 return; 1560 } 1561 1562 for (i = 0; i < 2; i++) { 1563 struct scatterlist *sg = &s->sg_rx[i]; 1564 1565 sg_init_table(sg, 1); 1566 s->rx_buf[i] = buf; 1567 sg_dma_address(sg) = dma; 1568 sg_dma_len(sg) = s->buf_len_rx; 1569 1570 buf += s->buf_len_rx; 1571 dma += s->buf_len_rx; 1572 } 1573 1574 timer_setup(&s->rx_timer, rx_timer_fn, 0); 1575 1576 if (port->type == PORT_SCIFA || port->type == PORT_SCIFB) 1577 sci_submit_rx(s); 1578 } 1579 } 1580 1581 static void sci_free_dma(struct uart_port *port) 1582 { 1583 struct sci_port *s = to_sci_port(port); 1584 1585 if (s->chan_tx) 1586 sci_tx_dma_release(s, false); 1587 if (s->chan_rx) 1588 sci_rx_dma_release(s, false); 1589 } 1590 1591 static void sci_flush_buffer(struct uart_port *port) 1592 { 1593 /* 1594 * In uart_flush_buffer(), the xmit circular buffer has just been 1595 * cleared, so we have to reset tx_dma_len accordingly. 1596 */ 1597 to_sci_port(port)->tx_dma_len = 0; 1598 } 1599 #else /* !CONFIG_SERIAL_SH_SCI_DMA */ 1600 static inline void sci_request_dma(struct uart_port *port) 1601 { 1602 } 1603 1604 static inline void sci_free_dma(struct uart_port *port) 1605 { 1606 } 1607 1608 #define sci_flush_buffer NULL 1609 #endif /* !CONFIG_SERIAL_SH_SCI_DMA */ 1610 1611 static irqreturn_t sci_rx_interrupt(int irq, void *ptr) 1612 { 1613 struct uart_port *port = ptr; 1614 struct sci_port *s = to_sci_port(port); 1615 1616 #ifdef CONFIG_SERIAL_SH_SCI_DMA 1617 if (s->chan_rx) { 1618 u16 scr = serial_port_in(port, SCSCR); 1619 u16 ssr = serial_port_in(port, SCxSR); 1620 1621 /* Disable future Rx interrupts */ 1622 if (port->type == PORT_SCIFA || port->type == PORT_SCIFB) { 1623 disable_irq_nosync(irq); 1624 scr |= SCSCR_RDRQE; 1625 } else { 1626 scr &= ~SCSCR_RIE; 1627 sci_submit_rx(s); 1628 } 1629 serial_port_out(port, SCSCR, scr); 1630 /* Clear current interrupt */ 1631 serial_port_out(port, SCxSR, 1632 ssr & ~(SCIF_DR | SCxSR_RDxF(port))); 1633 dev_dbg(port->dev, "Rx IRQ %lu: setup t-out in %u jiffies\n", 1634 jiffies, s->rx_timeout); 1635 mod_timer(&s->rx_timer, jiffies + s->rx_timeout); 1636 1637 return IRQ_HANDLED; 1638 } 1639 #endif 1640 1641 if (s->rx_trigger > 1 && s->rx_fifo_timeout > 0) { 1642 if (!scif_rtrg_enabled(port)) 1643 scif_set_rtrg(port, s->rx_trigger); 1644 1645 mod_timer(&s->rx_fifo_timer, jiffies + DIV_ROUND_UP( 1646 s->rx_frame * s->rx_fifo_timeout, 1000)); 1647 } 1648 1649 /* I think sci_receive_chars has to be called irrespective 1650 * of whether the I_IXOFF is set, otherwise, how is the interrupt 1651 * to be disabled? 1652 */ 1653 sci_receive_chars(ptr); 1654 1655 return IRQ_HANDLED; 1656 } 1657 1658 static irqreturn_t sci_tx_interrupt(int irq, void *ptr) 1659 { 1660 struct uart_port *port = ptr; 1661 unsigned long flags; 1662 1663 spin_lock_irqsave(&port->lock, flags); 1664 sci_transmit_chars(port); 1665 spin_unlock_irqrestore(&port->lock, flags); 1666 1667 return IRQ_HANDLED; 1668 } 1669 1670 static irqreturn_t sci_er_interrupt(int irq, void *ptr) 1671 { 1672 struct uart_port *port = ptr; 1673 struct sci_port *s = to_sci_port(port); 1674 1675 /* Handle errors */ 1676 if (port->type == PORT_SCI) { 1677 if (sci_handle_errors(port)) { 1678 /* discard character in rx buffer */ 1679 serial_port_in(port, SCxSR); 1680 sci_clear_SCxSR(port, SCxSR_RDxF_CLEAR(port)); 1681 } 1682 } else { 1683 sci_handle_fifo_overrun(port); 1684 if (!s->chan_rx) 1685 sci_receive_chars(ptr); 1686 } 1687 1688 sci_clear_SCxSR(port, SCxSR_ERROR_CLEAR(port)); 1689 1690 /* Kick the transmission */ 1691 if (!s->chan_tx) 1692 sci_tx_interrupt(irq, ptr); 1693 1694 return IRQ_HANDLED; 1695 } 1696 1697 static irqreturn_t sci_br_interrupt(int irq, void *ptr) 1698 { 1699 struct uart_port *port = ptr; 1700 1701 /* Handle BREAKs */ 1702 sci_handle_breaks(port); 1703 sci_clear_SCxSR(port, SCxSR_BREAK_CLEAR(port)); 1704 1705 return IRQ_HANDLED; 1706 } 1707 1708 static irqreturn_t sci_mpxed_interrupt(int irq, void *ptr) 1709 { 1710 unsigned short ssr_status, scr_status, err_enabled, orer_status = 0; 1711 struct uart_port *port = ptr; 1712 struct sci_port *s = to_sci_port(port); 1713 irqreturn_t ret = IRQ_NONE; 1714 1715 ssr_status = serial_port_in(port, SCxSR); 1716 scr_status = serial_port_in(port, SCSCR); 1717 if (s->params->overrun_reg == SCxSR) 1718 orer_status = ssr_status; 1719 else if (sci_getreg(port, s->params->overrun_reg)->size) 1720 orer_status = serial_port_in(port, s->params->overrun_reg); 1721 1722 err_enabled = scr_status & port_rx_irq_mask(port); 1723 1724 /* Tx Interrupt */ 1725 if ((ssr_status & SCxSR_TDxE(port)) && (scr_status & SCSCR_TIE) && 1726 !s->chan_tx) 1727 ret = sci_tx_interrupt(irq, ptr); 1728 1729 /* 1730 * Rx Interrupt: if we're using DMA, the DMA controller clears RDF / 1731 * DR flags 1732 */ 1733 if (((ssr_status & SCxSR_RDxF(port)) || s->chan_rx) && 1734 (scr_status & SCSCR_RIE)) 1735 ret = sci_rx_interrupt(irq, ptr); 1736 1737 /* Error Interrupt */ 1738 if ((ssr_status & SCxSR_ERRORS(port)) && err_enabled) 1739 ret = sci_er_interrupt(irq, ptr); 1740 1741 /* Break Interrupt */ 1742 if ((ssr_status & SCxSR_BRK(port)) && err_enabled) 1743 ret = sci_br_interrupt(irq, ptr); 1744 1745 /* Overrun Interrupt */ 1746 if (orer_status & s->params->overrun_mask) { 1747 sci_handle_fifo_overrun(port); 1748 ret = IRQ_HANDLED; 1749 } 1750 1751 return ret; 1752 } 1753 1754 static const struct sci_irq_desc { 1755 const char *desc; 1756 irq_handler_t handler; 1757 } sci_irq_desc[] = { 1758 /* 1759 * Split out handlers, the default case. 1760 */ 1761 [SCIx_ERI_IRQ] = { 1762 .desc = "rx err", 1763 .handler = sci_er_interrupt, 1764 }, 1765 1766 [SCIx_RXI_IRQ] = { 1767 .desc = "rx full", 1768 .handler = sci_rx_interrupt, 1769 }, 1770 1771 [SCIx_TXI_IRQ] = { 1772 .desc = "tx empty", 1773 .handler = sci_tx_interrupt, 1774 }, 1775 1776 [SCIx_BRI_IRQ] = { 1777 .desc = "break", 1778 .handler = sci_br_interrupt, 1779 }, 1780 1781 /* 1782 * Special muxed handler. 1783 */ 1784 [SCIx_MUX_IRQ] = { 1785 .desc = "mux", 1786 .handler = sci_mpxed_interrupt, 1787 }, 1788 }; 1789 1790 static int sci_request_irq(struct sci_port *port) 1791 { 1792 struct uart_port *up = &port->port; 1793 int i, j, ret = 0; 1794 1795 for (i = j = 0; i < SCIx_NR_IRQS; i++, j++) { 1796 const struct sci_irq_desc *desc; 1797 int irq; 1798 1799 if (SCIx_IRQ_IS_MUXED(port)) { 1800 i = SCIx_MUX_IRQ; 1801 irq = up->irq; 1802 } else { 1803 irq = port->irqs[i]; 1804 1805 /* 1806 * Certain port types won't support all of the 1807 * available interrupt sources. 1808 */ 1809 if (unlikely(irq < 0)) 1810 continue; 1811 } 1812 1813 desc = sci_irq_desc + i; 1814 port->irqstr[j] = kasprintf(GFP_KERNEL, "%s:%s", 1815 dev_name(up->dev), desc->desc); 1816 if (!port->irqstr[j]) { 1817 ret = -ENOMEM; 1818 goto out_nomem; 1819 } 1820 1821 ret = request_irq(irq, desc->handler, up->irqflags, 1822 port->irqstr[j], port); 1823 if (unlikely(ret)) { 1824 dev_err(up->dev, "Can't allocate %s IRQ\n", desc->desc); 1825 goto out_noirq; 1826 } 1827 } 1828 1829 return 0; 1830 1831 out_noirq: 1832 while (--i >= 0) 1833 free_irq(port->irqs[i], port); 1834 1835 out_nomem: 1836 while (--j >= 0) 1837 kfree(port->irqstr[j]); 1838 1839 return ret; 1840 } 1841 1842 static void sci_free_irq(struct sci_port *port) 1843 { 1844 int i; 1845 1846 /* 1847 * Intentionally in reverse order so we iterate over the muxed 1848 * IRQ first. 1849 */ 1850 for (i = 0; i < SCIx_NR_IRQS; i++) { 1851 int irq = port->irqs[i]; 1852 1853 /* 1854 * Certain port types won't support all of the available 1855 * interrupt sources. 1856 */ 1857 if (unlikely(irq < 0)) 1858 continue; 1859 1860 free_irq(port->irqs[i], port); 1861 kfree(port->irqstr[i]); 1862 1863 if (SCIx_IRQ_IS_MUXED(port)) { 1864 /* If there's only one IRQ, we're done. */ 1865 return; 1866 } 1867 } 1868 } 1869 1870 static unsigned int sci_tx_empty(struct uart_port *port) 1871 { 1872 unsigned short status = serial_port_in(port, SCxSR); 1873 unsigned short in_tx_fifo = sci_txfill(port); 1874 1875 return (status & SCxSR_TEND(port)) && !in_tx_fifo ? TIOCSER_TEMT : 0; 1876 } 1877 1878 static void sci_set_rts(struct uart_port *port, bool state) 1879 { 1880 if (port->type == PORT_SCIFA || port->type == PORT_SCIFB) { 1881 u16 data = serial_port_in(port, SCPDR); 1882 1883 /* Active low */ 1884 if (state) 1885 data &= ~SCPDR_RTSD; 1886 else 1887 data |= SCPDR_RTSD; 1888 serial_port_out(port, SCPDR, data); 1889 1890 /* RTS# is output */ 1891 serial_port_out(port, SCPCR, 1892 serial_port_in(port, SCPCR) | SCPCR_RTSC); 1893 } else if (sci_getreg(port, SCSPTR)->size) { 1894 u16 ctrl = serial_port_in(port, SCSPTR); 1895 1896 /* Active low */ 1897 if (state) 1898 ctrl &= ~SCSPTR_RTSDT; 1899 else 1900 ctrl |= SCSPTR_RTSDT; 1901 serial_port_out(port, SCSPTR, ctrl); 1902 } 1903 } 1904 1905 static bool sci_get_cts(struct uart_port *port) 1906 { 1907 if (port->type == PORT_SCIFA || port->type == PORT_SCIFB) { 1908 /* Active low */ 1909 return !(serial_port_in(port, SCPDR) & SCPDR_CTSD); 1910 } else if (sci_getreg(port, SCSPTR)->size) { 1911 /* Active low */ 1912 return !(serial_port_in(port, SCSPTR) & SCSPTR_CTSDT); 1913 } 1914 1915 return true; 1916 } 1917 1918 /* 1919 * Modem control is a bit of a mixed bag for SCI(F) ports. Generally 1920 * CTS/RTS is supported in hardware by at least one port and controlled 1921 * via SCSPTR (SCxPCR for SCIFA/B parts), or external pins (presently 1922 * handled via the ->init_pins() op, which is a bit of a one-way street, 1923 * lacking any ability to defer pin control -- this will later be 1924 * converted over to the GPIO framework). 1925 * 1926 * Other modes (such as loopback) are supported generically on certain 1927 * port types, but not others. For these it's sufficient to test for the 1928 * existence of the support register and simply ignore the port type. 1929 */ 1930 static void sci_set_mctrl(struct uart_port *port, unsigned int mctrl) 1931 { 1932 struct sci_port *s = to_sci_port(port); 1933 1934 if (mctrl & TIOCM_LOOP) { 1935 const struct plat_sci_reg *reg; 1936 1937 /* 1938 * Standard loopback mode for SCFCR ports. 1939 */ 1940 reg = sci_getreg(port, SCFCR); 1941 if (reg->size) 1942 serial_port_out(port, SCFCR, 1943 serial_port_in(port, SCFCR) | 1944 SCFCR_LOOP); 1945 } 1946 1947 mctrl_gpio_set(s->gpios, mctrl); 1948 1949 if (!s->has_rtscts) 1950 return; 1951 1952 if (!(mctrl & TIOCM_RTS)) { 1953 /* Disable Auto RTS */ 1954 serial_port_out(port, SCFCR, 1955 serial_port_in(port, SCFCR) & ~SCFCR_MCE); 1956 1957 /* Clear RTS */ 1958 sci_set_rts(port, 0); 1959 } else if (s->autorts) { 1960 if (port->type == PORT_SCIFA || port->type == PORT_SCIFB) { 1961 /* Enable RTS# pin function */ 1962 serial_port_out(port, SCPCR, 1963 serial_port_in(port, SCPCR) & ~SCPCR_RTSC); 1964 } 1965 1966 /* Enable Auto RTS */ 1967 serial_port_out(port, SCFCR, 1968 serial_port_in(port, SCFCR) | SCFCR_MCE); 1969 } else { 1970 /* Set RTS */ 1971 sci_set_rts(port, 1); 1972 } 1973 } 1974 1975 static unsigned int sci_get_mctrl(struct uart_port *port) 1976 { 1977 struct sci_port *s = to_sci_port(port); 1978 struct mctrl_gpios *gpios = s->gpios; 1979 unsigned int mctrl = 0; 1980 1981 mctrl_gpio_get(gpios, &mctrl); 1982 1983 /* 1984 * CTS/RTS is handled in hardware when supported, while nothing 1985 * else is wired up. 1986 */ 1987 if (s->autorts) { 1988 if (sci_get_cts(port)) 1989 mctrl |= TIOCM_CTS; 1990 } else if (IS_ERR_OR_NULL(mctrl_gpio_to_gpiod(gpios, UART_GPIO_CTS))) { 1991 mctrl |= TIOCM_CTS; 1992 } 1993 if (IS_ERR_OR_NULL(mctrl_gpio_to_gpiod(gpios, UART_GPIO_DSR))) 1994 mctrl |= TIOCM_DSR; 1995 if (IS_ERR_OR_NULL(mctrl_gpio_to_gpiod(gpios, UART_GPIO_DCD))) 1996 mctrl |= TIOCM_CAR; 1997 1998 return mctrl; 1999 } 2000 2001 static void sci_enable_ms(struct uart_port *port) 2002 { 2003 mctrl_gpio_enable_ms(to_sci_port(port)->gpios); 2004 } 2005 2006 static void sci_break_ctl(struct uart_port *port, int break_state) 2007 { 2008 unsigned short scscr, scsptr; 2009 unsigned long flags; 2010 2011 /* check wheter the port has SCSPTR */ 2012 if (!sci_getreg(port, SCSPTR)->size) { 2013 /* 2014 * Not supported by hardware. Most parts couple break and rx 2015 * interrupts together, with break detection always enabled. 2016 */ 2017 return; 2018 } 2019 2020 spin_lock_irqsave(&port->lock, flags); 2021 scsptr = serial_port_in(port, SCSPTR); 2022 scscr = serial_port_in(port, SCSCR); 2023 2024 if (break_state == -1) { 2025 scsptr = (scsptr | SCSPTR_SPB2IO) & ~SCSPTR_SPB2DT; 2026 scscr &= ~SCSCR_TE; 2027 } else { 2028 scsptr = (scsptr | SCSPTR_SPB2DT) & ~SCSPTR_SPB2IO; 2029 scscr |= SCSCR_TE; 2030 } 2031 2032 serial_port_out(port, SCSPTR, scsptr); 2033 serial_port_out(port, SCSCR, scscr); 2034 spin_unlock_irqrestore(&port->lock, flags); 2035 } 2036 2037 static int sci_startup(struct uart_port *port) 2038 { 2039 struct sci_port *s = to_sci_port(port); 2040 int ret; 2041 2042 dev_dbg(port->dev, "%s(%d)\n", __func__, port->line); 2043 2044 sci_request_dma(port); 2045 2046 ret = sci_request_irq(s); 2047 if (unlikely(ret < 0)) { 2048 sci_free_dma(port); 2049 return ret; 2050 } 2051 2052 return 0; 2053 } 2054 2055 static void sci_shutdown(struct uart_port *port) 2056 { 2057 struct sci_port *s = to_sci_port(port); 2058 unsigned long flags; 2059 u16 scr; 2060 2061 dev_dbg(port->dev, "%s(%d)\n", __func__, port->line); 2062 2063 s->autorts = false; 2064 mctrl_gpio_disable_ms(to_sci_port(port)->gpios); 2065 2066 spin_lock_irqsave(&port->lock, flags); 2067 sci_stop_rx(port); 2068 sci_stop_tx(port); 2069 /* 2070 * Stop RX and TX, disable related interrupts, keep clock source 2071 * and HSCIF TOT bits 2072 */ 2073 scr = serial_port_in(port, SCSCR); 2074 serial_port_out(port, SCSCR, scr & 2075 (SCSCR_CKE1 | SCSCR_CKE0 | s->hscif_tot)); 2076 spin_unlock_irqrestore(&port->lock, flags); 2077 2078 #ifdef CONFIG_SERIAL_SH_SCI_DMA 2079 if (s->chan_rx) { 2080 dev_dbg(port->dev, "%s(%d) deleting rx_timer\n", __func__, 2081 port->line); 2082 del_timer_sync(&s->rx_timer); 2083 } 2084 #endif 2085 2086 sci_free_irq(s); 2087 sci_free_dma(port); 2088 } 2089 2090 static int sci_sck_calc(struct sci_port *s, unsigned int bps, 2091 unsigned int *srr) 2092 { 2093 unsigned long freq = s->clk_rates[SCI_SCK]; 2094 int err, min_err = INT_MAX; 2095 unsigned int sr; 2096 2097 if (s->port.type != PORT_HSCIF) 2098 freq *= 2; 2099 2100 for_each_sr(sr, s) { 2101 err = DIV_ROUND_CLOSEST(freq, sr) - bps; 2102 if (abs(err) >= abs(min_err)) 2103 continue; 2104 2105 min_err = err; 2106 *srr = sr - 1; 2107 2108 if (!err) 2109 break; 2110 } 2111 2112 dev_dbg(s->port.dev, "SCK: %u%+d bps using SR %u\n", bps, min_err, 2113 *srr + 1); 2114 return min_err; 2115 } 2116 2117 static int sci_brg_calc(struct sci_port *s, unsigned int bps, 2118 unsigned long freq, unsigned int *dlr, 2119 unsigned int *srr) 2120 { 2121 int err, min_err = INT_MAX; 2122 unsigned int sr, dl; 2123 2124 if (s->port.type != PORT_HSCIF) 2125 freq *= 2; 2126 2127 for_each_sr(sr, s) { 2128 dl = DIV_ROUND_CLOSEST(freq, sr * bps); 2129 dl = clamp(dl, 1U, 65535U); 2130 2131 err = DIV_ROUND_CLOSEST(freq, sr * dl) - bps; 2132 if (abs(err) >= abs(min_err)) 2133 continue; 2134 2135 min_err = err; 2136 *dlr = dl; 2137 *srr = sr - 1; 2138 2139 if (!err) 2140 break; 2141 } 2142 2143 dev_dbg(s->port.dev, "BRG: %u%+d bps using DL %u SR %u\n", bps, 2144 min_err, *dlr, *srr + 1); 2145 return min_err; 2146 } 2147 2148 /* calculate sample rate, BRR, and clock select */ 2149 static int sci_scbrr_calc(struct sci_port *s, unsigned int bps, 2150 unsigned int *brr, unsigned int *srr, 2151 unsigned int *cks) 2152 { 2153 unsigned long freq = s->clk_rates[SCI_FCK]; 2154 unsigned int sr, br, prediv, scrate, c; 2155 int err, min_err = INT_MAX; 2156 2157 if (s->port.type != PORT_HSCIF) 2158 freq *= 2; 2159 2160 /* 2161 * Find the combination of sample rate and clock select with the 2162 * smallest deviation from the desired baud rate. 2163 * Prefer high sample rates to maximise the receive margin. 2164 * 2165 * M: Receive margin (%) 2166 * N: Ratio of bit rate to clock (N = sampling rate) 2167 * D: Clock duty (D = 0 to 1.0) 2168 * L: Frame length (L = 9 to 12) 2169 * F: Absolute value of clock frequency deviation 2170 * 2171 * M = |(0.5 - 1 / 2 * N) - ((L - 0.5) * F) - 2172 * (|D - 0.5| / N * (1 + F))| 2173 * NOTE: Usually, treat D for 0.5, F is 0 by this calculation. 2174 */ 2175 for_each_sr(sr, s) { 2176 for (c = 0; c <= 3; c++) { 2177 /* integerized formulas from HSCIF documentation */ 2178 prediv = sr * (1 << (2 * c + 1)); 2179 2180 /* 2181 * We need to calculate: 2182 * 2183 * br = freq / (prediv * bps) clamped to [1..256] 2184 * err = freq / (br * prediv) - bps 2185 * 2186 * Watch out for overflow when calculating the desired 2187 * sampling clock rate! 2188 */ 2189 if (bps > UINT_MAX / prediv) 2190 break; 2191 2192 scrate = prediv * bps; 2193 br = DIV_ROUND_CLOSEST(freq, scrate); 2194 br = clamp(br, 1U, 256U); 2195 2196 err = DIV_ROUND_CLOSEST(freq, br * prediv) - bps; 2197 if (abs(err) >= abs(min_err)) 2198 continue; 2199 2200 min_err = err; 2201 *brr = br - 1; 2202 *srr = sr - 1; 2203 *cks = c; 2204 2205 if (!err) 2206 goto found; 2207 } 2208 } 2209 2210 found: 2211 dev_dbg(s->port.dev, "BRR: %u%+d bps using N %u SR %u cks %u\n", bps, 2212 min_err, *brr, *srr + 1, *cks); 2213 return min_err; 2214 } 2215 2216 static void sci_reset(struct uart_port *port) 2217 { 2218 const struct plat_sci_reg *reg; 2219 unsigned int status; 2220 struct sci_port *s = to_sci_port(port); 2221 2222 serial_port_out(port, SCSCR, s->hscif_tot); /* TE=0, RE=0, CKE1=0 */ 2223 2224 reg = sci_getreg(port, SCFCR); 2225 if (reg->size) 2226 serial_port_out(port, SCFCR, SCFCR_RFRST | SCFCR_TFRST); 2227 2228 sci_clear_SCxSR(port, 2229 SCxSR_RDxF_CLEAR(port) & SCxSR_ERROR_CLEAR(port) & 2230 SCxSR_BREAK_CLEAR(port)); 2231 if (sci_getreg(port, SCLSR)->size) { 2232 status = serial_port_in(port, SCLSR); 2233 status &= ~(SCLSR_TO | SCLSR_ORER); 2234 serial_port_out(port, SCLSR, status); 2235 } 2236 2237 if (s->rx_trigger > 1) { 2238 if (s->rx_fifo_timeout) { 2239 scif_set_rtrg(port, 1); 2240 timer_setup(&s->rx_fifo_timer, rx_fifo_timer_fn, 0); 2241 } else { 2242 if (port->type == PORT_SCIFA || 2243 port->type == PORT_SCIFB) 2244 scif_set_rtrg(port, 1); 2245 else 2246 scif_set_rtrg(port, s->rx_trigger); 2247 } 2248 } 2249 } 2250 2251 static void sci_set_termios(struct uart_port *port, struct ktermios *termios, 2252 struct ktermios *old) 2253 { 2254 unsigned int baud, smr_val = SCSMR_ASYNC, scr_val = 0, i, bits; 2255 unsigned int brr = 255, cks = 0, srr = 15, dl = 0, sccks = 0; 2256 unsigned int brr1 = 255, cks1 = 0, srr1 = 15, dl1 = 0; 2257 struct sci_port *s = to_sci_port(port); 2258 const struct plat_sci_reg *reg; 2259 int min_err = INT_MAX, err; 2260 unsigned long max_freq = 0; 2261 int best_clk = -1; 2262 unsigned long flags; 2263 2264 if ((termios->c_cflag & CSIZE) == CS7) 2265 smr_val |= SCSMR_CHR; 2266 if (termios->c_cflag & PARENB) 2267 smr_val |= SCSMR_PE; 2268 if (termios->c_cflag & PARODD) 2269 smr_val |= SCSMR_PE | SCSMR_ODD; 2270 if (termios->c_cflag & CSTOPB) 2271 smr_val |= SCSMR_STOP; 2272 2273 /* 2274 * earlyprintk comes here early on with port->uartclk set to zero. 2275 * the clock framework is not up and running at this point so here 2276 * we assume that 115200 is the maximum baud rate. please note that 2277 * the baud rate is not programmed during earlyprintk - it is assumed 2278 * that the previous boot loader has enabled required clocks and 2279 * setup the baud rate generator hardware for us already. 2280 */ 2281 if (!port->uartclk) { 2282 baud = uart_get_baud_rate(port, termios, old, 0, 115200); 2283 goto done; 2284 } 2285 2286 for (i = 0; i < SCI_NUM_CLKS; i++) 2287 max_freq = max(max_freq, s->clk_rates[i]); 2288 2289 baud = uart_get_baud_rate(port, termios, old, 0, max_freq / min_sr(s)); 2290 if (!baud) 2291 goto done; 2292 2293 /* 2294 * There can be multiple sources for the sampling clock. Find the one 2295 * that gives us the smallest deviation from the desired baud rate. 2296 */ 2297 2298 /* Optional Undivided External Clock */ 2299 if (s->clk_rates[SCI_SCK] && port->type != PORT_SCIFA && 2300 port->type != PORT_SCIFB) { 2301 err = sci_sck_calc(s, baud, &srr1); 2302 if (abs(err) < abs(min_err)) { 2303 best_clk = SCI_SCK; 2304 scr_val = SCSCR_CKE1; 2305 sccks = SCCKS_CKS; 2306 min_err = err; 2307 srr = srr1; 2308 if (!err) 2309 goto done; 2310 } 2311 } 2312 2313 /* Optional BRG Frequency Divided External Clock */ 2314 if (s->clk_rates[SCI_SCIF_CLK] && sci_getreg(port, SCDL)->size) { 2315 err = sci_brg_calc(s, baud, s->clk_rates[SCI_SCIF_CLK], &dl1, 2316 &srr1); 2317 if (abs(err) < abs(min_err)) { 2318 best_clk = SCI_SCIF_CLK; 2319 scr_val = SCSCR_CKE1; 2320 sccks = 0; 2321 min_err = err; 2322 dl = dl1; 2323 srr = srr1; 2324 if (!err) 2325 goto done; 2326 } 2327 } 2328 2329 /* Optional BRG Frequency Divided Internal Clock */ 2330 if (s->clk_rates[SCI_BRG_INT] && sci_getreg(port, SCDL)->size) { 2331 err = sci_brg_calc(s, baud, s->clk_rates[SCI_BRG_INT], &dl1, 2332 &srr1); 2333 if (abs(err) < abs(min_err)) { 2334 best_clk = SCI_BRG_INT; 2335 scr_val = SCSCR_CKE1; 2336 sccks = SCCKS_XIN; 2337 min_err = err; 2338 dl = dl1; 2339 srr = srr1; 2340 if (!min_err) 2341 goto done; 2342 } 2343 } 2344 2345 /* Divided Functional Clock using standard Bit Rate Register */ 2346 err = sci_scbrr_calc(s, baud, &brr1, &srr1, &cks1); 2347 if (abs(err) < abs(min_err)) { 2348 best_clk = SCI_FCK; 2349 scr_val = 0; 2350 min_err = err; 2351 brr = brr1; 2352 srr = srr1; 2353 cks = cks1; 2354 } 2355 2356 done: 2357 if (best_clk >= 0) 2358 dev_dbg(port->dev, "Using clk %pC for %u%+d bps\n", 2359 s->clks[best_clk], baud, min_err); 2360 2361 sci_port_enable(s); 2362 2363 /* 2364 * Program the optional External Baud Rate Generator (BRG) first. 2365 * It controls the mux to select (H)SCK or frequency divided clock. 2366 */ 2367 if (best_clk >= 0 && sci_getreg(port, SCCKS)->size) { 2368 serial_port_out(port, SCDL, dl); 2369 serial_port_out(port, SCCKS, sccks); 2370 } 2371 2372 spin_lock_irqsave(&port->lock, flags); 2373 2374 sci_reset(port); 2375 2376 uart_update_timeout(port, termios->c_cflag, baud); 2377 2378 if (best_clk >= 0) { 2379 if (port->type == PORT_SCIFA || port->type == PORT_SCIFB) 2380 switch (srr + 1) { 2381 case 5: smr_val |= SCSMR_SRC_5; break; 2382 case 7: smr_val |= SCSMR_SRC_7; break; 2383 case 11: smr_val |= SCSMR_SRC_11; break; 2384 case 13: smr_val |= SCSMR_SRC_13; break; 2385 case 16: smr_val |= SCSMR_SRC_16; break; 2386 case 17: smr_val |= SCSMR_SRC_17; break; 2387 case 19: smr_val |= SCSMR_SRC_19; break; 2388 case 27: smr_val |= SCSMR_SRC_27; break; 2389 } 2390 smr_val |= cks; 2391 serial_port_out(port, SCSCR, scr_val | s->hscif_tot); 2392 serial_port_out(port, SCSMR, smr_val); 2393 serial_port_out(port, SCBRR, brr); 2394 if (sci_getreg(port, HSSRR)->size) 2395 serial_port_out(port, HSSRR, srr | HSCIF_SRE); 2396 2397 /* Wait one bit interval */ 2398 udelay((1000000 + (baud - 1)) / baud); 2399 } else { 2400 /* Don't touch the bit rate configuration */ 2401 scr_val = s->cfg->scscr & (SCSCR_CKE1 | SCSCR_CKE0); 2402 smr_val |= serial_port_in(port, SCSMR) & 2403 (SCSMR_CKEDG | SCSMR_SRC_MASK | SCSMR_CKS); 2404 serial_port_out(port, SCSCR, scr_val | s->hscif_tot); 2405 serial_port_out(port, SCSMR, smr_val); 2406 } 2407 2408 sci_init_pins(port, termios->c_cflag); 2409 2410 port->status &= ~UPSTAT_AUTOCTS; 2411 s->autorts = false; 2412 reg = sci_getreg(port, SCFCR); 2413 if (reg->size) { 2414 unsigned short ctrl = serial_port_in(port, SCFCR); 2415 2416 if ((port->flags & UPF_HARD_FLOW) && 2417 (termios->c_cflag & CRTSCTS)) { 2418 /* There is no CTS interrupt to restart the hardware */ 2419 port->status |= UPSTAT_AUTOCTS; 2420 /* MCE is enabled when RTS is raised */ 2421 s->autorts = true; 2422 } 2423 2424 /* 2425 * As we've done a sci_reset() above, ensure we don't 2426 * interfere with the FIFOs while toggling MCE. As the 2427 * reset values could still be set, simply mask them out. 2428 */ 2429 ctrl &= ~(SCFCR_RFRST | SCFCR_TFRST); 2430 2431 serial_port_out(port, SCFCR, ctrl); 2432 } 2433 if (port->flags & UPF_HARD_FLOW) { 2434 /* Refresh (Auto) RTS */ 2435 sci_set_mctrl(port, port->mctrl); 2436 } 2437 2438 scr_val |= SCSCR_RE | SCSCR_TE | 2439 (s->cfg->scscr & ~(SCSCR_CKE1 | SCSCR_CKE0)); 2440 serial_port_out(port, SCSCR, scr_val | s->hscif_tot); 2441 if ((srr + 1 == 5) && 2442 (port->type == PORT_SCIFA || port->type == PORT_SCIFB)) { 2443 /* 2444 * In asynchronous mode, when the sampling rate is 1/5, first 2445 * received data may become invalid on some SCIFA and SCIFB. 2446 * To avoid this problem wait more than 1 serial data time (1 2447 * bit time x serial data number) after setting SCSCR.RE = 1. 2448 */ 2449 udelay(DIV_ROUND_UP(10 * 1000000, baud)); 2450 } 2451 2452 /* 2453 * Calculate delay for 2 DMA buffers (4 FIFO). 2454 * See serial_core.c::uart_update_timeout(). 2455 * With 10 bits (CS8), 250Hz, 115200 baud and 64 bytes FIFO, the above 2456 * function calculates 1 jiffie for the data plus 5 jiffies for the 2457 * "slop(e)." Then below we calculate 5 jiffies (20ms) for 2 DMA 2458 * buffers (4 FIFO sizes), but when performing a faster transfer, the 2459 * value obtained by this formula is too small. Therefore, if the value 2460 * is smaller than 20ms, use 20ms as the timeout value for DMA. 2461 */ 2462 /* byte size and parity */ 2463 switch (termios->c_cflag & CSIZE) { 2464 case CS5: 2465 bits = 7; 2466 break; 2467 case CS6: 2468 bits = 8; 2469 break; 2470 case CS7: 2471 bits = 9; 2472 break; 2473 default: 2474 bits = 10; 2475 break; 2476 } 2477 2478 if (termios->c_cflag & CSTOPB) 2479 bits++; 2480 if (termios->c_cflag & PARENB) 2481 bits++; 2482 2483 s->rx_frame = (100 * bits * HZ) / (baud / 10); 2484 #ifdef CONFIG_SERIAL_SH_SCI_DMA 2485 s->rx_timeout = DIV_ROUND_UP(s->buf_len_rx * 2 * s->rx_frame, 1000); 2486 if (s->rx_timeout < msecs_to_jiffies(20)) 2487 s->rx_timeout = msecs_to_jiffies(20); 2488 #endif 2489 2490 if ((termios->c_cflag & CREAD) != 0) 2491 sci_start_rx(port); 2492 2493 spin_unlock_irqrestore(&port->lock, flags); 2494 2495 sci_port_disable(s); 2496 2497 if (UART_ENABLE_MS(port, termios->c_cflag)) 2498 sci_enable_ms(port); 2499 } 2500 2501 static void sci_pm(struct uart_port *port, unsigned int state, 2502 unsigned int oldstate) 2503 { 2504 struct sci_port *sci_port = to_sci_port(port); 2505 2506 switch (state) { 2507 case UART_PM_STATE_OFF: 2508 sci_port_disable(sci_port); 2509 break; 2510 default: 2511 sci_port_enable(sci_port); 2512 break; 2513 } 2514 } 2515 2516 static const char *sci_type(struct uart_port *port) 2517 { 2518 switch (port->type) { 2519 case PORT_IRDA: 2520 return "irda"; 2521 case PORT_SCI: 2522 return "sci"; 2523 case PORT_SCIF: 2524 return "scif"; 2525 case PORT_SCIFA: 2526 return "scifa"; 2527 case PORT_SCIFB: 2528 return "scifb"; 2529 case PORT_HSCIF: 2530 return "hscif"; 2531 } 2532 2533 return NULL; 2534 } 2535 2536 static int sci_remap_port(struct uart_port *port) 2537 { 2538 struct sci_port *sport = to_sci_port(port); 2539 2540 /* 2541 * Nothing to do if there's already an established membase. 2542 */ 2543 if (port->membase) 2544 return 0; 2545 2546 if (port->dev->of_node || (port->flags & UPF_IOREMAP)) { 2547 port->membase = ioremap_nocache(port->mapbase, sport->reg_size); 2548 if (unlikely(!port->membase)) { 2549 dev_err(port->dev, "can't remap port#%d\n", port->line); 2550 return -ENXIO; 2551 } 2552 } else { 2553 /* 2554 * For the simple (and majority of) cases where we don't 2555 * need to do any remapping, just cast the cookie 2556 * directly. 2557 */ 2558 port->membase = (void __iomem *)(uintptr_t)port->mapbase; 2559 } 2560 2561 return 0; 2562 } 2563 2564 static void sci_release_port(struct uart_port *port) 2565 { 2566 struct sci_port *sport = to_sci_port(port); 2567 2568 if (port->dev->of_node || (port->flags & UPF_IOREMAP)) { 2569 iounmap(port->membase); 2570 port->membase = NULL; 2571 } 2572 2573 release_mem_region(port->mapbase, sport->reg_size); 2574 } 2575 2576 static int sci_request_port(struct uart_port *port) 2577 { 2578 struct resource *res; 2579 struct sci_port *sport = to_sci_port(port); 2580 int ret; 2581 2582 res = request_mem_region(port->mapbase, sport->reg_size, 2583 dev_name(port->dev)); 2584 if (unlikely(res == NULL)) { 2585 dev_err(port->dev, "request_mem_region failed."); 2586 return -EBUSY; 2587 } 2588 2589 ret = sci_remap_port(port); 2590 if (unlikely(ret != 0)) { 2591 release_resource(res); 2592 return ret; 2593 } 2594 2595 return 0; 2596 } 2597 2598 static void sci_config_port(struct uart_port *port, int flags) 2599 { 2600 if (flags & UART_CONFIG_TYPE) { 2601 struct sci_port *sport = to_sci_port(port); 2602 2603 port->type = sport->cfg->type; 2604 sci_request_port(port); 2605 } 2606 } 2607 2608 static int sci_verify_port(struct uart_port *port, struct serial_struct *ser) 2609 { 2610 if (ser->baud_base < 2400) 2611 /* No paper tape reader for Mitch.. */ 2612 return -EINVAL; 2613 2614 return 0; 2615 } 2616 2617 static const struct uart_ops sci_uart_ops = { 2618 .tx_empty = sci_tx_empty, 2619 .set_mctrl = sci_set_mctrl, 2620 .get_mctrl = sci_get_mctrl, 2621 .start_tx = sci_start_tx, 2622 .stop_tx = sci_stop_tx, 2623 .stop_rx = sci_stop_rx, 2624 .enable_ms = sci_enable_ms, 2625 .break_ctl = sci_break_ctl, 2626 .startup = sci_startup, 2627 .shutdown = sci_shutdown, 2628 .flush_buffer = sci_flush_buffer, 2629 .set_termios = sci_set_termios, 2630 .pm = sci_pm, 2631 .type = sci_type, 2632 .release_port = sci_release_port, 2633 .request_port = sci_request_port, 2634 .config_port = sci_config_port, 2635 .verify_port = sci_verify_port, 2636 #ifdef CONFIG_CONSOLE_POLL 2637 .poll_get_char = sci_poll_get_char, 2638 .poll_put_char = sci_poll_put_char, 2639 #endif 2640 }; 2641 2642 static int sci_init_clocks(struct sci_port *sci_port, struct device *dev) 2643 { 2644 const char *clk_names[] = { 2645 [SCI_FCK] = "fck", 2646 [SCI_SCK] = "sck", 2647 [SCI_BRG_INT] = "brg_int", 2648 [SCI_SCIF_CLK] = "scif_clk", 2649 }; 2650 struct clk *clk; 2651 unsigned int i; 2652 2653 if (sci_port->cfg->type == PORT_HSCIF) 2654 clk_names[SCI_SCK] = "hsck"; 2655 2656 for (i = 0; i < SCI_NUM_CLKS; i++) { 2657 clk = devm_clk_get(dev, clk_names[i]); 2658 if (PTR_ERR(clk) == -EPROBE_DEFER) 2659 return -EPROBE_DEFER; 2660 2661 if (IS_ERR(clk) && i == SCI_FCK) { 2662 /* 2663 * "fck" used to be called "sci_ick", and we need to 2664 * maintain DT backward compatibility. 2665 */ 2666 clk = devm_clk_get(dev, "sci_ick"); 2667 if (PTR_ERR(clk) == -EPROBE_DEFER) 2668 return -EPROBE_DEFER; 2669 2670 if (!IS_ERR(clk)) 2671 goto found; 2672 2673 /* 2674 * Not all SH platforms declare a clock lookup entry 2675 * for SCI devices, in which case we need to get the 2676 * global "peripheral_clk" clock. 2677 */ 2678 clk = devm_clk_get(dev, "peripheral_clk"); 2679 if (!IS_ERR(clk)) 2680 goto found; 2681 2682 dev_err(dev, "failed to get %s (%ld)\n", clk_names[i], 2683 PTR_ERR(clk)); 2684 return PTR_ERR(clk); 2685 } 2686 2687 found: 2688 if (IS_ERR(clk)) 2689 dev_dbg(dev, "failed to get %s (%ld)\n", clk_names[i], 2690 PTR_ERR(clk)); 2691 else 2692 dev_dbg(dev, "clk %s is %pC rate %pCr\n", clk_names[i], 2693 clk, clk); 2694 sci_port->clks[i] = IS_ERR(clk) ? NULL : clk; 2695 } 2696 return 0; 2697 } 2698 2699 static const struct sci_port_params * 2700 sci_probe_regmap(const struct plat_sci_port *cfg) 2701 { 2702 unsigned int regtype; 2703 2704 if (cfg->regtype != SCIx_PROBE_REGTYPE) 2705 return &sci_port_params[cfg->regtype]; 2706 2707 switch (cfg->type) { 2708 case PORT_SCI: 2709 regtype = SCIx_SCI_REGTYPE; 2710 break; 2711 case PORT_IRDA: 2712 regtype = SCIx_IRDA_REGTYPE; 2713 break; 2714 case PORT_SCIFA: 2715 regtype = SCIx_SCIFA_REGTYPE; 2716 break; 2717 case PORT_SCIFB: 2718 regtype = SCIx_SCIFB_REGTYPE; 2719 break; 2720 case PORT_SCIF: 2721 /* 2722 * The SH-4 is a bit of a misnomer here, although that's 2723 * where this particular port layout originated. This 2724 * configuration (or some slight variation thereof) 2725 * remains the dominant model for all SCIFs. 2726 */ 2727 regtype = SCIx_SH4_SCIF_REGTYPE; 2728 break; 2729 case PORT_HSCIF: 2730 regtype = SCIx_HSCIF_REGTYPE; 2731 break; 2732 default: 2733 pr_err("Can't probe register map for given port\n"); 2734 return NULL; 2735 } 2736 2737 return &sci_port_params[regtype]; 2738 } 2739 2740 static int sci_init_single(struct platform_device *dev, 2741 struct sci_port *sci_port, unsigned int index, 2742 const struct plat_sci_port *p, bool early) 2743 { 2744 struct uart_port *port = &sci_port->port; 2745 const struct resource *res; 2746 unsigned int i; 2747 int ret; 2748 2749 sci_port->cfg = p; 2750 2751 port->ops = &sci_uart_ops; 2752 port->iotype = UPIO_MEM; 2753 port->line = index; 2754 2755 res = platform_get_resource(dev, IORESOURCE_MEM, 0); 2756 if (res == NULL) 2757 return -ENOMEM; 2758 2759 port->mapbase = res->start; 2760 sci_port->reg_size = resource_size(res); 2761 2762 for (i = 0; i < ARRAY_SIZE(sci_port->irqs); ++i) 2763 sci_port->irqs[i] = platform_get_irq(dev, i); 2764 2765 /* The SCI generates several interrupts. They can be muxed together or 2766 * connected to different interrupt lines. In the muxed case only one 2767 * interrupt resource is specified. In the non-muxed case three or four 2768 * interrupt resources are specified, as the BRI interrupt is optional. 2769 */ 2770 if (sci_port->irqs[0] < 0) 2771 return -ENXIO; 2772 2773 if (sci_port->irqs[1] < 0) { 2774 sci_port->irqs[1] = sci_port->irqs[0]; 2775 sci_port->irqs[2] = sci_port->irqs[0]; 2776 sci_port->irqs[3] = sci_port->irqs[0]; 2777 } 2778 2779 sci_port->params = sci_probe_regmap(p); 2780 if (unlikely(sci_port->params == NULL)) 2781 return -EINVAL; 2782 2783 switch (p->type) { 2784 case PORT_SCIFB: 2785 sci_port->rx_trigger = 48; 2786 break; 2787 case PORT_HSCIF: 2788 sci_port->rx_trigger = 64; 2789 break; 2790 case PORT_SCIFA: 2791 sci_port->rx_trigger = 32; 2792 break; 2793 case PORT_SCIF: 2794 if (p->regtype == SCIx_SH7705_SCIF_REGTYPE) 2795 /* RX triggering not implemented for this IP */ 2796 sci_port->rx_trigger = 1; 2797 else 2798 sci_port->rx_trigger = 8; 2799 break; 2800 default: 2801 sci_port->rx_trigger = 1; 2802 break; 2803 } 2804 2805 sci_port->rx_fifo_timeout = 0; 2806 sci_port->hscif_tot = 0; 2807 2808 /* SCIFA on sh7723 and sh7724 need a custom sampling rate that doesn't 2809 * match the SoC datasheet, this should be investigated. Let platform 2810 * data override the sampling rate for now. 2811 */ 2812 sci_port->sampling_rate_mask = p->sampling_rate 2813 ? SCI_SR(p->sampling_rate) 2814 : sci_port->params->sampling_rate_mask; 2815 2816 if (!early) { 2817 ret = sci_init_clocks(sci_port, &dev->dev); 2818 if (ret < 0) 2819 return ret; 2820 2821 port->dev = &dev->dev; 2822 2823 pm_runtime_enable(&dev->dev); 2824 } 2825 2826 port->type = p->type; 2827 port->flags = UPF_FIXED_PORT | UPF_BOOT_AUTOCONF | p->flags; 2828 port->fifosize = sci_port->params->fifosize; 2829 2830 if (port->type == PORT_SCI) { 2831 if (sci_port->reg_size >= 0x20) 2832 port->regshift = 2; 2833 else 2834 port->regshift = 1; 2835 } 2836 2837 /* 2838 * The UART port needs an IRQ value, so we peg this to the RX IRQ 2839 * for the multi-IRQ ports, which is where we are primarily 2840 * concerned with the shutdown path synchronization. 2841 * 2842 * For the muxed case there's nothing more to do. 2843 */ 2844 port->irq = sci_port->irqs[SCIx_RXI_IRQ]; 2845 port->irqflags = 0; 2846 2847 port->serial_in = sci_serial_in; 2848 port->serial_out = sci_serial_out; 2849 2850 return 0; 2851 } 2852 2853 static void sci_cleanup_single(struct sci_port *port) 2854 { 2855 pm_runtime_disable(port->port.dev); 2856 } 2857 2858 #if defined(CONFIG_SERIAL_SH_SCI_CONSOLE) || \ 2859 defined(CONFIG_SERIAL_SH_SCI_EARLYCON) 2860 static void serial_console_putchar(struct uart_port *port, int ch) 2861 { 2862 sci_poll_put_char(port, ch); 2863 } 2864 2865 /* 2866 * Print a string to the serial port trying not to disturb 2867 * any possible real use of the port... 2868 */ 2869 static void serial_console_write(struct console *co, const char *s, 2870 unsigned count) 2871 { 2872 struct sci_port *sci_port = &sci_ports[co->index]; 2873 struct uart_port *port = &sci_port->port; 2874 unsigned short bits, ctrl, ctrl_temp; 2875 unsigned long flags; 2876 int locked = 1; 2877 2878 local_irq_save(flags); 2879 #if defined(SUPPORT_SYSRQ) 2880 if (port->sysrq) 2881 locked = 0; 2882 else 2883 #endif 2884 if (oops_in_progress) 2885 locked = spin_trylock(&port->lock); 2886 else 2887 spin_lock(&port->lock); 2888 2889 /* first save SCSCR then disable interrupts, keep clock source */ 2890 ctrl = serial_port_in(port, SCSCR); 2891 ctrl_temp = SCSCR_RE | SCSCR_TE | 2892 (sci_port->cfg->scscr & ~(SCSCR_CKE1 | SCSCR_CKE0)) | 2893 (ctrl & (SCSCR_CKE1 | SCSCR_CKE0)); 2894 serial_port_out(port, SCSCR, ctrl_temp | sci_port->hscif_tot); 2895 2896 uart_console_write(port, s, count, serial_console_putchar); 2897 2898 /* wait until fifo is empty and last bit has been transmitted */ 2899 bits = SCxSR_TDxE(port) | SCxSR_TEND(port); 2900 while ((serial_port_in(port, SCxSR) & bits) != bits) 2901 cpu_relax(); 2902 2903 /* restore the SCSCR */ 2904 serial_port_out(port, SCSCR, ctrl); 2905 2906 if (locked) 2907 spin_unlock(&port->lock); 2908 local_irq_restore(flags); 2909 } 2910 2911 static int serial_console_setup(struct console *co, char *options) 2912 { 2913 struct sci_port *sci_port; 2914 struct uart_port *port; 2915 int baud = 115200; 2916 int bits = 8; 2917 int parity = 'n'; 2918 int flow = 'n'; 2919 int ret; 2920 2921 /* 2922 * Refuse to handle any bogus ports. 2923 */ 2924 if (co->index < 0 || co->index >= SCI_NPORTS) 2925 return -ENODEV; 2926 2927 sci_port = &sci_ports[co->index]; 2928 port = &sci_port->port; 2929 2930 /* 2931 * Refuse to handle uninitialized ports. 2932 */ 2933 if (!port->ops) 2934 return -ENODEV; 2935 2936 ret = sci_remap_port(port); 2937 if (unlikely(ret != 0)) 2938 return ret; 2939 2940 if (options) 2941 uart_parse_options(options, &baud, &parity, &bits, &flow); 2942 2943 return uart_set_options(port, co, baud, parity, bits, flow); 2944 } 2945 2946 static struct console serial_console = { 2947 .name = "ttySC", 2948 .device = uart_console_device, 2949 .write = serial_console_write, 2950 .setup = serial_console_setup, 2951 .flags = CON_PRINTBUFFER, 2952 .index = -1, 2953 .data = &sci_uart_driver, 2954 }; 2955 2956 static struct console early_serial_console = { 2957 .name = "early_ttySC", 2958 .write = serial_console_write, 2959 .flags = CON_PRINTBUFFER, 2960 .index = -1, 2961 }; 2962 2963 static char early_serial_buf[32]; 2964 2965 static int sci_probe_earlyprintk(struct platform_device *pdev) 2966 { 2967 const struct plat_sci_port *cfg = dev_get_platdata(&pdev->dev); 2968 2969 if (early_serial_console.data) 2970 return -EEXIST; 2971 2972 early_serial_console.index = pdev->id; 2973 2974 sci_init_single(pdev, &sci_ports[pdev->id], pdev->id, cfg, true); 2975 2976 serial_console_setup(&early_serial_console, early_serial_buf); 2977 2978 if (!strstr(early_serial_buf, "keep")) 2979 early_serial_console.flags |= CON_BOOT; 2980 2981 register_console(&early_serial_console); 2982 return 0; 2983 } 2984 2985 #define SCI_CONSOLE (&serial_console) 2986 2987 #else 2988 static inline int sci_probe_earlyprintk(struct platform_device *pdev) 2989 { 2990 return -EINVAL; 2991 } 2992 2993 #define SCI_CONSOLE NULL 2994 2995 #endif /* CONFIG_SERIAL_SH_SCI_CONSOLE || CONFIG_SERIAL_SH_SCI_EARLYCON */ 2996 2997 static const char banner[] __initconst = "SuperH (H)SCI(F) driver initialized"; 2998 2999 static DEFINE_MUTEX(sci_uart_registration_lock); 3000 static struct uart_driver sci_uart_driver = { 3001 .owner = THIS_MODULE, 3002 .driver_name = "sci", 3003 .dev_name = "ttySC", 3004 .major = SCI_MAJOR, 3005 .minor = SCI_MINOR_START, 3006 .nr = SCI_NPORTS, 3007 .cons = SCI_CONSOLE, 3008 }; 3009 3010 static int sci_remove(struct platform_device *dev) 3011 { 3012 struct sci_port *port = platform_get_drvdata(dev); 3013 3014 uart_remove_one_port(&sci_uart_driver, &port->port); 3015 3016 sci_cleanup_single(port); 3017 3018 if (port->port.fifosize > 1) { 3019 sysfs_remove_file(&dev->dev.kobj, 3020 &dev_attr_rx_fifo_trigger.attr); 3021 } 3022 if (port->port.type == PORT_SCIFA || port->port.type == PORT_SCIFB || 3023 port->port.type == PORT_HSCIF) { 3024 sysfs_remove_file(&dev->dev.kobj, 3025 &dev_attr_rx_fifo_timeout.attr); 3026 } 3027 3028 return 0; 3029 } 3030 3031 3032 #define SCI_OF_DATA(type, regtype) (void *)((type) << 16 | (regtype)) 3033 #define SCI_OF_TYPE(data) ((unsigned long)(data) >> 16) 3034 #define SCI_OF_REGTYPE(data) ((unsigned long)(data) & 0xffff) 3035 3036 static const struct of_device_id of_sci_match[] = { 3037 /* SoC-specific types */ 3038 { 3039 .compatible = "renesas,scif-r7s72100", 3040 .data = SCI_OF_DATA(PORT_SCIF, SCIx_SH2_SCIF_FIFODATA_REGTYPE), 3041 }, 3042 /* Family-specific types */ 3043 { 3044 .compatible = "renesas,rcar-gen1-scif", 3045 .data = SCI_OF_DATA(PORT_SCIF, SCIx_SH4_SCIF_BRG_REGTYPE), 3046 }, { 3047 .compatible = "renesas,rcar-gen2-scif", 3048 .data = SCI_OF_DATA(PORT_SCIF, SCIx_SH4_SCIF_BRG_REGTYPE), 3049 }, { 3050 .compatible = "renesas,rcar-gen3-scif", 3051 .data = SCI_OF_DATA(PORT_SCIF, SCIx_SH4_SCIF_BRG_REGTYPE), 3052 }, 3053 /* Generic types */ 3054 { 3055 .compatible = "renesas,scif", 3056 .data = SCI_OF_DATA(PORT_SCIF, SCIx_SH4_SCIF_REGTYPE), 3057 }, { 3058 .compatible = "renesas,scifa", 3059 .data = SCI_OF_DATA(PORT_SCIFA, SCIx_SCIFA_REGTYPE), 3060 }, { 3061 .compatible = "renesas,scifb", 3062 .data = SCI_OF_DATA(PORT_SCIFB, SCIx_SCIFB_REGTYPE), 3063 }, { 3064 .compatible = "renesas,hscif", 3065 .data = SCI_OF_DATA(PORT_HSCIF, SCIx_HSCIF_REGTYPE), 3066 }, { 3067 .compatible = "renesas,sci", 3068 .data = SCI_OF_DATA(PORT_SCI, SCIx_SCI_REGTYPE), 3069 }, { 3070 /* Terminator */ 3071 }, 3072 }; 3073 MODULE_DEVICE_TABLE(of, of_sci_match); 3074 3075 static struct plat_sci_port *sci_parse_dt(struct platform_device *pdev, 3076 unsigned int *dev_id) 3077 { 3078 struct device_node *np = pdev->dev.of_node; 3079 struct plat_sci_port *p; 3080 struct sci_port *sp; 3081 const void *data; 3082 int id; 3083 3084 if (!IS_ENABLED(CONFIG_OF) || !np) 3085 return NULL; 3086 3087 data = of_device_get_match_data(&pdev->dev); 3088 3089 p = devm_kzalloc(&pdev->dev, sizeof(struct plat_sci_port), GFP_KERNEL); 3090 if (!p) 3091 return NULL; 3092 3093 /* Get the line number from the aliases node. */ 3094 id = of_alias_get_id(np, "serial"); 3095 if (id < 0) { 3096 dev_err(&pdev->dev, "failed to get alias id (%d)\n", id); 3097 return NULL; 3098 } 3099 3100 sp = &sci_ports[id]; 3101 *dev_id = id; 3102 3103 p->type = SCI_OF_TYPE(data); 3104 p->regtype = SCI_OF_REGTYPE(data); 3105 3106 sp->has_rtscts = of_property_read_bool(np, "uart-has-rtscts"); 3107 3108 return p; 3109 } 3110 3111 static int sci_probe_single(struct platform_device *dev, 3112 unsigned int index, 3113 struct plat_sci_port *p, 3114 struct sci_port *sciport) 3115 { 3116 int ret; 3117 3118 /* Sanity check */ 3119 if (unlikely(index >= SCI_NPORTS)) { 3120 dev_notice(&dev->dev, "Attempting to register port %d when only %d are available\n", 3121 index+1, SCI_NPORTS); 3122 dev_notice(&dev->dev, "Consider bumping CONFIG_SERIAL_SH_SCI_NR_UARTS!\n"); 3123 return -EINVAL; 3124 } 3125 3126 mutex_lock(&sci_uart_registration_lock); 3127 if (!sci_uart_driver.state) { 3128 ret = uart_register_driver(&sci_uart_driver); 3129 if (ret) { 3130 mutex_unlock(&sci_uart_registration_lock); 3131 return ret; 3132 } 3133 } 3134 mutex_unlock(&sci_uart_registration_lock); 3135 3136 ret = sci_init_single(dev, sciport, index, p, false); 3137 if (ret) 3138 return ret; 3139 3140 sciport->gpios = mctrl_gpio_init(&sciport->port, 0); 3141 if (IS_ERR(sciport->gpios) && PTR_ERR(sciport->gpios) != -ENOSYS) 3142 return PTR_ERR(sciport->gpios); 3143 3144 if (sciport->has_rtscts) { 3145 if (!IS_ERR_OR_NULL(mctrl_gpio_to_gpiod(sciport->gpios, 3146 UART_GPIO_CTS)) || 3147 !IS_ERR_OR_NULL(mctrl_gpio_to_gpiod(sciport->gpios, 3148 UART_GPIO_RTS))) { 3149 dev_err(&dev->dev, "Conflicting RTS/CTS config\n"); 3150 return -EINVAL; 3151 } 3152 sciport->port.flags |= UPF_HARD_FLOW; 3153 } 3154 3155 ret = uart_add_one_port(&sci_uart_driver, &sciport->port); 3156 if (ret) { 3157 sci_cleanup_single(sciport); 3158 return ret; 3159 } 3160 3161 return 0; 3162 } 3163 3164 static int sci_probe(struct platform_device *dev) 3165 { 3166 struct plat_sci_port *p; 3167 struct sci_port *sp; 3168 unsigned int dev_id; 3169 int ret; 3170 3171 /* 3172 * If we've come here via earlyprintk initialization, head off to 3173 * the special early probe. We don't have sufficient device state 3174 * to make it beyond this yet. 3175 */ 3176 if (is_early_platform_device(dev)) 3177 return sci_probe_earlyprintk(dev); 3178 3179 if (dev->dev.of_node) { 3180 p = sci_parse_dt(dev, &dev_id); 3181 if (p == NULL) 3182 return -EINVAL; 3183 } else { 3184 p = dev->dev.platform_data; 3185 if (p == NULL) { 3186 dev_err(&dev->dev, "no platform data supplied\n"); 3187 return -EINVAL; 3188 } 3189 3190 dev_id = dev->id; 3191 } 3192 3193 sp = &sci_ports[dev_id]; 3194 platform_set_drvdata(dev, sp); 3195 3196 ret = sci_probe_single(dev, dev_id, p, sp); 3197 if (ret) 3198 return ret; 3199 3200 if (sp->port.fifosize > 1) { 3201 ret = sysfs_create_file(&dev->dev.kobj, 3202 &dev_attr_rx_fifo_trigger.attr); 3203 if (ret) 3204 return ret; 3205 } 3206 if (sp->port.type == PORT_SCIFA || sp->port.type == PORT_SCIFB || 3207 sp->port.type == PORT_HSCIF) { 3208 ret = sysfs_create_file(&dev->dev.kobj, 3209 &dev_attr_rx_fifo_timeout.attr); 3210 if (ret) { 3211 if (sp->port.fifosize > 1) { 3212 sysfs_remove_file(&dev->dev.kobj, 3213 &dev_attr_rx_fifo_trigger.attr); 3214 } 3215 return ret; 3216 } 3217 } 3218 3219 #ifdef CONFIG_SH_STANDARD_BIOS 3220 sh_bios_gdb_detach(); 3221 #endif 3222 3223 return 0; 3224 } 3225 3226 static __maybe_unused int sci_suspend(struct device *dev) 3227 { 3228 struct sci_port *sport = dev_get_drvdata(dev); 3229 3230 if (sport) 3231 uart_suspend_port(&sci_uart_driver, &sport->port); 3232 3233 return 0; 3234 } 3235 3236 static __maybe_unused int sci_resume(struct device *dev) 3237 { 3238 struct sci_port *sport = dev_get_drvdata(dev); 3239 3240 if (sport) 3241 uart_resume_port(&sci_uart_driver, &sport->port); 3242 3243 return 0; 3244 } 3245 3246 static SIMPLE_DEV_PM_OPS(sci_dev_pm_ops, sci_suspend, sci_resume); 3247 3248 static struct platform_driver sci_driver = { 3249 .probe = sci_probe, 3250 .remove = sci_remove, 3251 .driver = { 3252 .name = "sh-sci", 3253 .pm = &sci_dev_pm_ops, 3254 .of_match_table = of_match_ptr(of_sci_match), 3255 }, 3256 }; 3257 3258 static int __init sci_init(void) 3259 { 3260 pr_info("%s\n", banner); 3261 3262 return platform_driver_register(&sci_driver); 3263 } 3264 3265 static void __exit sci_exit(void) 3266 { 3267 platform_driver_unregister(&sci_driver); 3268 3269 if (sci_uart_driver.state) 3270 uart_unregister_driver(&sci_uart_driver); 3271 } 3272 3273 #ifdef CONFIG_SERIAL_SH_SCI_CONSOLE 3274 early_platform_init_buffer("earlyprintk", &sci_driver, 3275 early_serial_buf, ARRAY_SIZE(early_serial_buf)); 3276 #endif 3277 #ifdef CONFIG_SERIAL_SH_SCI_EARLYCON 3278 static struct plat_sci_port port_cfg __initdata; 3279 3280 static int __init early_console_setup(struct earlycon_device *device, 3281 int type) 3282 { 3283 if (!device->port.membase) 3284 return -ENODEV; 3285 3286 device->port.serial_in = sci_serial_in; 3287 device->port.serial_out = sci_serial_out; 3288 device->port.type = type; 3289 memcpy(&sci_ports[0].port, &device->port, sizeof(struct uart_port)); 3290 port_cfg.type = type; 3291 sci_ports[0].cfg = &port_cfg; 3292 sci_ports[0].params = sci_probe_regmap(&port_cfg); 3293 port_cfg.scscr = sci_serial_in(&sci_ports[0].port, SCSCR); 3294 sci_serial_out(&sci_ports[0].port, SCSCR, 3295 SCSCR_RE | SCSCR_TE | port_cfg.scscr); 3296 3297 device->con->write = serial_console_write; 3298 return 0; 3299 } 3300 static int __init sci_early_console_setup(struct earlycon_device *device, 3301 const char *opt) 3302 { 3303 return early_console_setup(device, PORT_SCI); 3304 } 3305 static int __init scif_early_console_setup(struct earlycon_device *device, 3306 const char *opt) 3307 { 3308 return early_console_setup(device, PORT_SCIF); 3309 } 3310 static int __init scifa_early_console_setup(struct earlycon_device *device, 3311 const char *opt) 3312 { 3313 return early_console_setup(device, PORT_SCIFA); 3314 } 3315 static int __init scifb_early_console_setup(struct earlycon_device *device, 3316 const char *opt) 3317 { 3318 return early_console_setup(device, PORT_SCIFB); 3319 } 3320 static int __init hscif_early_console_setup(struct earlycon_device *device, 3321 const char *opt) 3322 { 3323 return early_console_setup(device, PORT_HSCIF); 3324 } 3325 3326 OF_EARLYCON_DECLARE(sci, "renesas,sci", sci_early_console_setup); 3327 OF_EARLYCON_DECLARE(scif, "renesas,scif", scif_early_console_setup); 3328 OF_EARLYCON_DECLARE(scifa, "renesas,scifa", scifa_early_console_setup); 3329 OF_EARLYCON_DECLARE(scifb, "renesas,scifb", scifb_early_console_setup); 3330 OF_EARLYCON_DECLARE(hscif, "renesas,hscif", hscif_early_console_setup); 3331 #endif /* CONFIG_SERIAL_SH_SCI_EARLYCON */ 3332 3333 module_init(sci_init); 3334 module_exit(sci_exit); 3335 3336 MODULE_LICENSE("GPL"); 3337 MODULE_ALIAS("platform:sh-sci"); 3338 MODULE_AUTHOR("Paul Mundt"); 3339 MODULE_DESCRIPTION("SuperH (H)SCI(F) serial driver"); 3340