1 // SPDX-License-Identifier: GPL-2.0+ 2 /* 3 * NXP (Philips) SCC+++(SCN+++) serial driver 4 * 5 * Copyright (C) 2012 Alexander Shiyan <shc_work@mail.ru> 6 * 7 * Based on sc26xx.c, by Thomas Bogendörfer (tsbogend@alpha.franken.de) 8 */ 9 10 #if defined(CONFIG_SERIAL_SCCNXP_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ) 11 #define SUPPORT_SYSRQ 12 #endif 13 14 #include <linux/clk.h> 15 #include <linux/delay.h> 16 #include <linux/err.h> 17 #include <linux/module.h> 18 #include <linux/mod_devicetable.h> 19 #include <linux/device.h> 20 #include <linux/console.h> 21 #include <linux/serial_core.h> 22 #include <linux/serial.h> 23 #include <linux/io.h> 24 #include <linux/tty.h> 25 #include <linux/tty_flip.h> 26 #include <linux/spinlock.h> 27 #include <linux/platform_device.h> 28 #include <linux/platform_data/serial-sccnxp.h> 29 #include <linux/regulator/consumer.h> 30 31 #define SCCNXP_NAME "uart-sccnxp" 32 #define SCCNXP_MAJOR 204 33 #define SCCNXP_MINOR 205 34 35 #define SCCNXP_MR_REG (0x00) 36 # define MR0_BAUD_NORMAL (0 << 0) 37 # define MR0_BAUD_EXT1 (1 << 0) 38 # define MR0_BAUD_EXT2 (5 << 0) 39 # define MR0_FIFO (1 << 3) 40 # define MR0_TXLVL (1 << 4) 41 # define MR1_BITS_5 (0 << 0) 42 # define MR1_BITS_6 (1 << 0) 43 # define MR1_BITS_7 (2 << 0) 44 # define MR1_BITS_8 (3 << 0) 45 # define MR1_PAR_EVN (0 << 2) 46 # define MR1_PAR_ODD (1 << 2) 47 # define MR1_PAR_NO (4 << 2) 48 # define MR2_STOP1 (7 << 0) 49 # define MR2_STOP2 (0xf << 0) 50 #define SCCNXP_SR_REG (0x01) 51 # define SR_RXRDY (1 << 0) 52 # define SR_FULL (1 << 1) 53 # define SR_TXRDY (1 << 2) 54 # define SR_TXEMT (1 << 3) 55 # define SR_OVR (1 << 4) 56 # define SR_PE (1 << 5) 57 # define SR_FE (1 << 6) 58 # define SR_BRK (1 << 7) 59 #define SCCNXP_CSR_REG (SCCNXP_SR_REG) 60 # define CSR_TIMER_MODE (0x0d) 61 #define SCCNXP_CR_REG (0x02) 62 # define CR_RX_ENABLE (1 << 0) 63 # define CR_RX_DISABLE (1 << 1) 64 # define CR_TX_ENABLE (1 << 2) 65 # define CR_TX_DISABLE (1 << 3) 66 # define CR_CMD_MRPTR1 (0x01 << 4) 67 # define CR_CMD_RX_RESET (0x02 << 4) 68 # define CR_CMD_TX_RESET (0x03 << 4) 69 # define CR_CMD_STATUS_RESET (0x04 << 4) 70 # define CR_CMD_BREAK_RESET (0x05 << 4) 71 # define CR_CMD_START_BREAK (0x06 << 4) 72 # define CR_CMD_STOP_BREAK (0x07 << 4) 73 # define CR_CMD_MRPTR0 (0x0b << 4) 74 #define SCCNXP_RHR_REG (0x03) 75 #define SCCNXP_THR_REG SCCNXP_RHR_REG 76 #define SCCNXP_IPCR_REG (0x04) 77 #define SCCNXP_ACR_REG SCCNXP_IPCR_REG 78 # define ACR_BAUD0 (0 << 7) 79 # define ACR_BAUD1 (1 << 7) 80 # define ACR_TIMER_MODE (6 << 4) 81 #define SCCNXP_ISR_REG (0x05) 82 #define SCCNXP_IMR_REG SCCNXP_ISR_REG 83 # define IMR_TXRDY (1 << 0) 84 # define IMR_RXRDY (1 << 1) 85 # define ISR_TXRDY(x) (1 << ((x * 4) + 0)) 86 # define ISR_RXRDY(x) (1 << ((x * 4) + 1)) 87 #define SCCNXP_CTPU_REG (0x06) 88 #define SCCNXP_CTPL_REG (0x07) 89 #define SCCNXP_IPR_REG (0x0d) 90 #define SCCNXP_OPCR_REG SCCNXP_IPR_REG 91 #define SCCNXP_SOP_REG (0x0e) 92 #define SCCNXP_START_COUNTER_REG SCCNXP_SOP_REG 93 #define SCCNXP_ROP_REG (0x0f) 94 95 /* Route helpers */ 96 #define MCTRL_MASK(sig) (0xf << (sig)) 97 #define MCTRL_IBIT(cfg, sig) ((((cfg) >> (sig)) & 0xf) - LINE_IP0) 98 #define MCTRL_OBIT(cfg, sig) ((((cfg) >> (sig)) & 0xf) - LINE_OP0) 99 100 #define SCCNXP_HAVE_IO 0x00000001 101 #define SCCNXP_HAVE_MR0 0x00000002 102 103 struct sccnxp_chip { 104 const char *name; 105 unsigned int nr; 106 unsigned long freq_min; 107 unsigned long freq_std; 108 unsigned long freq_max; 109 unsigned int flags; 110 unsigned int fifosize; 111 /* Time between read/write cycles */ 112 unsigned int trwd; 113 }; 114 115 struct sccnxp_port { 116 struct uart_driver uart; 117 struct uart_port port[SCCNXP_MAX_UARTS]; 118 bool opened[SCCNXP_MAX_UARTS]; 119 120 int irq; 121 u8 imr; 122 123 struct sccnxp_chip *chip; 124 125 #ifdef CONFIG_SERIAL_SCCNXP_CONSOLE 126 struct console console; 127 #endif 128 129 spinlock_t lock; 130 131 bool poll; 132 struct timer_list timer; 133 134 struct sccnxp_pdata pdata; 135 136 struct regulator *regulator; 137 }; 138 139 static const struct sccnxp_chip sc2681 = { 140 .name = "SC2681", 141 .nr = 2, 142 .freq_min = 1000000, 143 .freq_std = 3686400, 144 .freq_max = 4000000, 145 .flags = SCCNXP_HAVE_IO, 146 .fifosize = 3, 147 .trwd = 200, 148 }; 149 150 static const struct sccnxp_chip sc2691 = { 151 .name = "SC2691", 152 .nr = 1, 153 .freq_min = 1000000, 154 .freq_std = 3686400, 155 .freq_max = 4000000, 156 .flags = 0, 157 .fifosize = 3, 158 .trwd = 150, 159 }; 160 161 static const struct sccnxp_chip sc2692 = { 162 .name = "SC2692", 163 .nr = 2, 164 .freq_min = 1000000, 165 .freq_std = 3686400, 166 .freq_max = 4000000, 167 .flags = SCCNXP_HAVE_IO, 168 .fifosize = 3, 169 .trwd = 30, 170 }; 171 172 static const struct sccnxp_chip sc2891 = { 173 .name = "SC2891", 174 .nr = 1, 175 .freq_min = 100000, 176 .freq_std = 3686400, 177 .freq_max = 8000000, 178 .flags = SCCNXP_HAVE_IO | SCCNXP_HAVE_MR0, 179 .fifosize = 16, 180 .trwd = 27, 181 }; 182 183 static const struct sccnxp_chip sc2892 = { 184 .name = "SC2892", 185 .nr = 2, 186 .freq_min = 100000, 187 .freq_std = 3686400, 188 .freq_max = 8000000, 189 .flags = SCCNXP_HAVE_IO | SCCNXP_HAVE_MR0, 190 .fifosize = 16, 191 .trwd = 17, 192 }; 193 194 static const struct sccnxp_chip sc28202 = { 195 .name = "SC28202", 196 .nr = 2, 197 .freq_min = 1000000, 198 .freq_std = 14745600, 199 .freq_max = 50000000, 200 .flags = SCCNXP_HAVE_IO | SCCNXP_HAVE_MR0, 201 .fifosize = 256, 202 .trwd = 10, 203 }; 204 205 static const struct sccnxp_chip sc68681 = { 206 .name = "SC68681", 207 .nr = 2, 208 .freq_min = 1000000, 209 .freq_std = 3686400, 210 .freq_max = 4000000, 211 .flags = SCCNXP_HAVE_IO, 212 .fifosize = 3, 213 .trwd = 200, 214 }; 215 216 static const struct sccnxp_chip sc68692 = { 217 .name = "SC68692", 218 .nr = 2, 219 .freq_min = 1000000, 220 .freq_std = 3686400, 221 .freq_max = 4000000, 222 .flags = SCCNXP_HAVE_IO, 223 .fifosize = 3, 224 .trwd = 200, 225 }; 226 227 static u8 sccnxp_read(struct uart_port *port, u8 reg) 228 { 229 struct sccnxp_port *s = dev_get_drvdata(port->dev); 230 u8 ret; 231 232 ret = readb(port->membase + (reg << port->regshift)); 233 234 ndelay(s->chip->trwd); 235 236 return ret; 237 } 238 239 static void sccnxp_write(struct uart_port *port, u8 reg, u8 v) 240 { 241 struct sccnxp_port *s = dev_get_drvdata(port->dev); 242 243 writeb(v, port->membase + (reg << port->regshift)); 244 245 ndelay(s->chip->trwd); 246 } 247 248 static u8 sccnxp_port_read(struct uart_port *port, u8 reg) 249 { 250 return sccnxp_read(port, (port->line << 3) + reg); 251 } 252 253 static void sccnxp_port_write(struct uart_port *port, u8 reg, u8 v) 254 { 255 sccnxp_write(port, (port->line << 3) + reg, v); 256 } 257 258 static int sccnxp_update_best_err(int a, int b, int *besterr) 259 { 260 int err = abs(a - b); 261 262 if (*besterr > err) { 263 *besterr = err; 264 return 0; 265 } 266 267 return 1; 268 } 269 270 static const struct { 271 u8 csr; 272 u8 acr; 273 u8 mr0; 274 int baud; 275 } baud_std[] = { 276 { 0, ACR_BAUD0, MR0_BAUD_NORMAL, 50, }, 277 { 0, ACR_BAUD1, MR0_BAUD_NORMAL, 75, }, 278 { 1, ACR_BAUD0, MR0_BAUD_NORMAL, 110, }, 279 { 2, ACR_BAUD0, MR0_BAUD_NORMAL, 134, }, 280 { 3, ACR_BAUD1, MR0_BAUD_NORMAL, 150, }, 281 { 3, ACR_BAUD0, MR0_BAUD_NORMAL, 200, }, 282 { 4, ACR_BAUD0, MR0_BAUD_NORMAL, 300, }, 283 { 0, ACR_BAUD1, MR0_BAUD_EXT1, 450, }, 284 { 1, ACR_BAUD0, MR0_BAUD_EXT2, 880, }, 285 { 3, ACR_BAUD1, MR0_BAUD_EXT1, 900, }, 286 { 5, ACR_BAUD0, MR0_BAUD_NORMAL, 600, }, 287 { 7, ACR_BAUD0, MR0_BAUD_NORMAL, 1050, }, 288 { 2, ACR_BAUD0, MR0_BAUD_EXT2, 1076, }, 289 { 6, ACR_BAUD0, MR0_BAUD_NORMAL, 1200, }, 290 { 10, ACR_BAUD1, MR0_BAUD_NORMAL, 1800, }, 291 { 7, ACR_BAUD1, MR0_BAUD_NORMAL, 2000, }, 292 { 8, ACR_BAUD0, MR0_BAUD_NORMAL, 2400, }, 293 { 5, ACR_BAUD1, MR0_BAUD_EXT1, 3600, }, 294 { 9, ACR_BAUD0, MR0_BAUD_NORMAL, 4800, }, 295 { 10, ACR_BAUD0, MR0_BAUD_NORMAL, 7200, }, 296 { 11, ACR_BAUD0, MR0_BAUD_NORMAL, 9600, }, 297 { 8, ACR_BAUD0, MR0_BAUD_EXT1, 14400, }, 298 { 12, ACR_BAUD1, MR0_BAUD_NORMAL, 19200, }, 299 { 9, ACR_BAUD0, MR0_BAUD_EXT1, 28800, }, 300 { 12, ACR_BAUD0, MR0_BAUD_NORMAL, 38400, }, 301 { 11, ACR_BAUD0, MR0_BAUD_EXT1, 57600, }, 302 { 12, ACR_BAUD1, MR0_BAUD_EXT1, 115200, }, 303 { 12, ACR_BAUD0, MR0_BAUD_EXT1, 230400, }, 304 { 0, 0, 0, 0 } 305 }; 306 307 static int sccnxp_set_baud(struct uart_port *port, int baud) 308 { 309 struct sccnxp_port *s = dev_get_drvdata(port->dev); 310 int div_std, tmp_baud, bestbaud = INT_MAX, besterr = INT_MAX; 311 struct sccnxp_chip *chip = s->chip; 312 u8 i, acr = 0, csr = 0, mr0 = 0; 313 314 /* Find divisor to load to the timer preset registers */ 315 div_std = DIV_ROUND_CLOSEST(port->uartclk, 2 * 16 * baud); 316 if ((div_std >= 2) && (div_std <= 0xffff)) { 317 bestbaud = DIV_ROUND_CLOSEST(port->uartclk, 2 * 16 * div_std); 318 sccnxp_update_best_err(baud, bestbaud, &besterr); 319 csr = CSR_TIMER_MODE; 320 sccnxp_port_write(port, SCCNXP_CTPU_REG, div_std >> 8); 321 sccnxp_port_write(port, SCCNXP_CTPL_REG, div_std); 322 /* Issue start timer/counter command */ 323 sccnxp_port_read(port, SCCNXP_START_COUNTER_REG); 324 } 325 326 /* Find best baud from table */ 327 for (i = 0; baud_std[i].baud && besterr; i++) { 328 if (baud_std[i].mr0 && !(chip->flags & SCCNXP_HAVE_MR0)) 329 continue; 330 div_std = DIV_ROUND_CLOSEST(chip->freq_std, baud_std[i].baud); 331 tmp_baud = DIV_ROUND_CLOSEST(port->uartclk, div_std); 332 if (!sccnxp_update_best_err(baud, tmp_baud, &besterr)) { 333 acr = baud_std[i].acr; 334 csr = baud_std[i].csr; 335 mr0 = baud_std[i].mr0; 336 bestbaud = tmp_baud; 337 } 338 } 339 340 if (chip->flags & SCCNXP_HAVE_MR0) { 341 /* Enable FIFO, set half level for TX */ 342 mr0 |= MR0_FIFO | MR0_TXLVL; 343 /* Update MR0 */ 344 sccnxp_port_write(port, SCCNXP_CR_REG, CR_CMD_MRPTR0); 345 sccnxp_port_write(port, SCCNXP_MR_REG, mr0); 346 } 347 348 sccnxp_port_write(port, SCCNXP_ACR_REG, acr | ACR_TIMER_MODE); 349 sccnxp_port_write(port, SCCNXP_CSR_REG, (csr << 4) | csr); 350 351 if (baud != bestbaud) 352 dev_dbg(port->dev, "Baudrate desired: %i, calculated: %i\n", 353 baud, bestbaud); 354 355 return bestbaud; 356 } 357 358 static void sccnxp_enable_irq(struct uart_port *port, int mask) 359 { 360 struct sccnxp_port *s = dev_get_drvdata(port->dev); 361 362 s->imr |= mask << (port->line * 4); 363 sccnxp_write(port, SCCNXP_IMR_REG, s->imr); 364 } 365 366 static void sccnxp_disable_irq(struct uart_port *port, int mask) 367 { 368 struct sccnxp_port *s = dev_get_drvdata(port->dev); 369 370 s->imr &= ~(mask << (port->line * 4)); 371 sccnxp_write(port, SCCNXP_IMR_REG, s->imr); 372 } 373 374 static void sccnxp_set_bit(struct uart_port *port, int sig, int state) 375 { 376 u8 bitmask; 377 struct sccnxp_port *s = dev_get_drvdata(port->dev); 378 379 if (s->pdata.mctrl_cfg[port->line] & MCTRL_MASK(sig)) { 380 bitmask = 1 << MCTRL_OBIT(s->pdata.mctrl_cfg[port->line], sig); 381 if (state) 382 sccnxp_write(port, SCCNXP_SOP_REG, bitmask); 383 else 384 sccnxp_write(port, SCCNXP_ROP_REG, bitmask); 385 } 386 } 387 388 static void sccnxp_handle_rx(struct uart_port *port) 389 { 390 u8 sr; 391 unsigned int ch, flag; 392 393 for (;;) { 394 sr = sccnxp_port_read(port, SCCNXP_SR_REG); 395 if (!(sr & SR_RXRDY)) 396 break; 397 sr &= SR_PE | SR_FE | SR_OVR | SR_BRK; 398 399 ch = sccnxp_port_read(port, SCCNXP_RHR_REG); 400 401 port->icount.rx++; 402 flag = TTY_NORMAL; 403 404 if (unlikely(sr)) { 405 if (sr & SR_BRK) { 406 port->icount.brk++; 407 sccnxp_port_write(port, SCCNXP_CR_REG, 408 CR_CMD_BREAK_RESET); 409 if (uart_handle_break(port)) 410 continue; 411 } else if (sr & SR_PE) 412 port->icount.parity++; 413 else if (sr & SR_FE) 414 port->icount.frame++; 415 else if (sr & SR_OVR) { 416 port->icount.overrun++; 417 sccnxp_port_write(port, SCCNXP_CR_REG, 418 CR_CMD_STATUS_RESET); 419 } 420 421 sr &= port->read_status_mask; 422 if (sr & SR_BRK) 423 flag = TTY_BREAK; 424 else if (sr & SR_PE) 425 flag = TTY_PARITY; 426 else if (sr & SR_FE) 427 flag = TTY_FRAME; 428 else if (sr & SR_OVR) 429 flag = TTY_OVERRUN; 430 } 431 432 if (uart_handle_sysrq_char(port, ch)) 433 continue; 434 435 if (sr & port->ignore_status_mask) 436 continue; 437 438 uart_insert_char(port, sr, SR_OVR, ch, flag); 439 } 440 441 tty_flip_buffer_push(&port->state->port); 442 } 443 444 static void sccnxp_handle_tx(struct uart_port *port) 445 { 446 u8 sr; 447 struct circ_buf *xmit = &port->state->xmit; 448 struct sccnxp_port *s = dev_get_drvdata(port->dev); 449 450 if (unlikely(port->x_char)) { 451 sccnxp_port_write(port, SCCNXP_THR_REG, port->x_char); 452 port->icount.tx++; 453 port->x_char = 0; 454 return; 455 } 456 457 if (uart_circ_empty(xmit) || uart_tx_stopped(port)) { 458 /* Disable TX if FIFO is empty */ 459 if (sccnxp_port_read(port, SCCNXP_SR_REG) & SR_TXEMT) { 460 sccnxp_disable_irq(port, IMR_TXRDY); 461 462 /* Set direction to input */ 463 if (s->chip->flags & SCCNXP_HAVE_IO) 464 sccnxp_set_bit(port, DIR_OP, 0); 465 } 466 return; 467 } 468 469 while (!uart_circ_empty(xmit)) { 470 sr = sccnxp_port_read(port, SCCNXP_SR_REG); 471 if (!(sr & SR_TXRDY)) 472 break; 473 474 sccnxp_port_write(port, SCCNXP_THR_REG, xmit->buf[xmit->tail]); 475 xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1); 476 port->icount.tx++; 477 } 478 479 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) 480 uart_write_wakeup(port); 481 } 482 483 static void sccnxp_handle_events(struct sccnxp_port *s) 484 { 485 int i; 486 u8 isr; 487 488 do { 489 isr = sccnxp_read(&s->port[0], SCCNXP_ISR_REG); 490 isr &= s->imr; 491 if (!isr) 492 break; 493 494 for (i = 0; i < s->uart.nr; i++) { 495 if (s->opened[i] && (isr & ISR_RXRDY(i))) 496 sccnxp_handle_rx(&s->port[i]); 497 if (s->opened[i] && (isr & ISR_TXRDY(i))) 498 sccnxp_handle_tx(&s->port[i]); 499 } 500 } while (1); 501 } 502 503 static void sccnxp_timer(struct timer_list *t) 504 { 505 struct sccnxp_port *s = from_timer(s, t, timer); 506 unsigned long flags; 507 508 spin_lock_irqsave(&s->lock, flags); 509 sccnxp_handle_events(s); 510 spin_unlock_irqrestore(&s->lock, flags); 511 512 mod_timer(&s->timer, jiffies + usecs_to_jiffies(s->pdata.poll_time_us)); 513 } 514 515 static irqreturn_t sccnxp_ist(int irq, void *dev_id) 516 { 517 struct sccnxp_port *s = (struct sccnxp_port *)dev_id; 518 unsigned long flags; 519 520 spin_lock_irqsave(&s->lock, flags); 521 sccnxp_handle_events(s); 522 spin_unlock_irqrestore(&s->lock, flags); 523 524 return IRQ_HANDLED; 525 } 526 527 static void sccnxp_start_tx(struct uart_port *port) 528 { 529 struct sccnxp_port *s = dev_get_drvdata(port->dev); 530 unsigned long flags; 531 532 spin_lock_irqsave(&s->lock, flags); 533 534 /* Set direction to output */ 535 if (s->chip->flags & SCCNXP_HAVE_IO) 536 sccnxp_set_bit(port, DIR_OP, 1); 537 538 sccnxp_enable_irq(port, IMR_TXRDY); 539 540 spin_unlock_irqrestore(&s->lock, flags); 541 } 542 543 static void sccnxp_stop_tx(struct uart_port *port) 544 { 545 /* Do nothing */ 546 } 547 548 static void sccnxp_stop_rx(struct uart_port *port) 549 { 550 struct sccnxp_port *s = dev_get_drvdata(port->dev); 551 unsigned long flags; 552 553 spin_lock_irqsave(&s->lock, flags); 554 sccnxp_port_write(port, SCCNXP_CR_REG, CR_RX_DISABLE); 555 spin_unlock_irqrestore(&s->lock, flags); 556 } 557 558 static unsigned int sccnxp_tx_empty(struct uart_port *port) 559 { 560 u8 val; 561 unsigned long flags; 562 struct sccnxp_port *s = dev_get_drvdata(port->dev); 563 564 spin_lock_irqsave(&s->lock, flags); 565 val = sccnxp_port_read(port, SCCNXP_SR_REG); 566 spin_unlock_irqrestore(&s->lock, flags); 567 568 return (val & SR_TXEMT) ? TIOCSER_TEMT : 0; 569 } 570 571 static void sccnxp_set_mctrl(struct uart_port *port, unsigned int mctrl) 572 { 573 struct sccnxp_port *s = dev_get_drvdata(port->dev); 574 unsigned long flags; 575 576 if (!(s->chip->flags & SCCNXP_HAVE_IO)) 577 return; 578 579 spin_lock_irqsave(&s->lock, flags); 580 581 sccnxp_set_bit(port, DTR_OP, mctrl & TIOCM_DTR); 582 sccnxp_set_bit(port, RTS_OP, mctrl & TIOCM_RTS); 583 584 spin_unlock_irqrestore(&s->lock, flags); 585 } 586 587 static unsigned int sccnxp_get_mctrl(struct uart_port *port) 588 { 589 u8 bitmask, ipr; 590 unsigned long flags; 591 struct sccnxp_port *s = dev_get_drvdata(port->dev); 592 unsigned int mctrl = TIOCM_DSR | TIOCM_CTS | TIOCM_CAR; 593 594 if (!(s->chip->flags & SCCNXP_HAVE_IO)) 595 return mctrl; 596 597 spin_lock_irqsave(&s->lock, flags); 598 599 ipr = ~sccnxp_read(port, SCCNXP_IPCR_REG); 600 601 if (s->pdata.mctrl_cfg[port->line] & MCTRL_MASK(DSR_IP)) { 602 bitmask = 1 << MCTRL_IBIT(s->pdata.mctrl_cfg[port->line], 603 DSR_IP); 604 mctrl &= ~TIOCM_DSR; 605 mctrl |= (ipr & bitmask) ? TIOCM_DSR : 0; 606 } 607 if (s->pdata.mctrl_cfg[port->line] & MCTRL_MASK(CTS_IP)) { 608 bitmask = 1 << MCTRL_IBIT(s->pdata.mctrl_cfg[port->line], 609 CTS_IP); 610 mctrl &= ~TIOCM_CTS; 611 mctrl |= (ipr & bitmask) ? TIOCM_CTS : 0; 612 } 613 if (s->pdata.mctrl_cfg[port->line] & MCTRL_MASK(DCD_IP)) { 614 bitmask = 1 << MCTRL_IBIT(s->pdata.mctrl_cfg[port->line], 615 DCD_IP); 616 mctrl &= ~TIOCM_CAR; 617 mctrl |= (ipr & bitmask) ? TIOCM_CAR : 0; 618 } 619 if (s->pdata.mctrl_cfg[port->line] & MCTRL_MASK(RNG_IP)) { 620 bitmask = 1 << MCTRL_IBIT(s->pdata.mctrl_cfg[port->line], 621 RNG_IP); 622 mctrl &= ~TIOCM_RNG; 623 mctrl |= (ipr & bitmask) ? TIOCM_RNG : 0; 624 } 625 626 spin_unlock_irqrestore(&s->lock, flags); 627 628 return mctrl; 629 } 630 631 static void sccnxp_break_ctl(struct uart_port *port, int break_state) 632 { 633 struct sccnxp_port *s = dev_get_drvdata(port->dev); 634 unsigned long flags; 635 636 spin_lock_irqsave(&s->lock, flags); 637 sccnxp_port_write(port, SCCNXP_CR_REG, break_state ? 638 CR_CMD_START_BREAK : CR_CMD_STOP_BREAK); 639 spin_unlock_irqrestore(&s->lock, flags); 640 } 641 642 static void sccnxp_set_termios(struct uart_port *port, 643 struct ktermios *termios, struct ktermios *old) 644 { 645 struct sccnxp_port *s = dev_get_drvdata(port->dev); 646 unsigned long flags; 647 u8 mr1, mr2; 648 int baud; 649 650 spin_lock_irqsave(&s->lock, flags); 651 652 /* Mask termios capabilities we don't support */ 653 termios->c_cflag &= ~CMSPAR; 654 655 /* Disable RX & TX, reset break condition, status and FIFOs */ 656 sccnxp_port_write(port, SCCNXP_CR_REG, CR_CMD_RX_RESET | 657 CR_RX_DISABLE | CR_TX_DISABLE); 658 sccnxp_port_write(port, SCCNXP_CR_REG, CR_CMD_TX_RESET); 659 sccnxp_port_write(port, SCCNXP_CR_REG, CR_CMD_STATUS_RESET); 660 sccnxp_port_write(port, SCCNXP_CR_REG, CR_CMD_BREAK_RESET); 661 662 /* Word size */ 663 switch (termios->c_cflag & CSIZE) { 664 case CS5: 665 mr1 = MR1_BITS_5; 666 break; 667 case CS6: 668 mr1 = MR1_BITS_6; 669 break; 670 case CS7: 671 mr1 = MR1_BITS_7; 672 break; 673 case CS8: 674 default: 675 mr1 = MR1_BITS_8; 676 break; 677 } 678 679 /* Parity */ 680 if (termios->c_cflag & PARENB) { 681 if (termios->c_cflag & PARODD) 682 mr1 |= MR1_PAR_ODD; 683 } else 684 mr1 |= MR1_PAR_NO; 685 686 /* Stop bits */ 687 mr2 = (termios->c_cflag & CSTOPB) ? MR2_STOP2 : MR2_STOP1; 688 689 /* Update desired format */ 690 sccnxp_port_write(port, SCCNXP_CR_REG, CR_CMD_MRPTR1); 691 sccnxp_port_write(port, SCCNXP_MR_REG, mr1); 692 sccnxp_port_write(port, SCCNXP_MR_REG, mr2); 693 694 /* Set read status mask */ 695 port->read_status_mask = SR_OVR; 696 if (termios->c_iflag & INPCK) 697 port->read_status_mask |= SR_PE | SR_FE; 698 if (termios->c_iflag & (IGNBRK | BRKINT | PARMRK)) 699 port->read_status_mask |= SR_BRK; 700 701 /* Set status ignore mask */ 702 port->ignore_status_mask = 0; 703 if (termios->c_iflag & IGNBRK) 704 port->ignore_status_mask |= SR_BRK; 705 if (termios->c_iflag & IGNPAR) 706 port->ignore_status_mask |= SR_PE; 707 if (!(termios->c_cflag & CREAD)) 708 port->ignore_status_mask |= SR_PE | SR_OVR | SR_FE | SR_BRK; 709 710 /* Setup baudrate */ 711 baud = uart_get_baud_rate(port, termios, old, 50, 712 (s->chip->flags & SCCNXP_HAVE_MR0) ? 713 230400 : 38400); 714 baud = sccnxp_set_baud(port, baud); 715 716 /* Update timeout according to new baud rate */ 717 uart_update_timeout(port, termios->c_cflag, baud); 718 719 /* Report actual baudrate back to core */ 720 if (tty_termios_baud_rate(termios)) 721 tty_termios_encode_baud_rate(termios, baud, baud); 722 723 /* Enable RX & TX */ 724 sccnxp_port_write(port, SCCNXP_CR_REG, CR_RX_ENABLE | CR_TX_ENABLE); 725 726 spin_unlock_irqrestore(&s->lock, flags); 727 } 728 729 static int sccnxp_startup(struct uart_port *port) 730 { 731 struct sccnxp_port *s = dev_get_drvdata(port->dev); 732 unsigned long flags; 733 734 spin_lock_irqsave(&s->lock, flags); 735 736 if (s->chip->flags & SCCNXP_HAVE_IO) { 737 /* Outputs are controlled manually */ 738 sccnxp_write(port, SCCNXP_OPCR_REG, 0); 739 } 740 741 /* Reset break condition, status and FIFOs */ 742 sccnxp_port_write(port, SCCNXP_CR_REG, CR_CMD_RX_RESET); 743 sccnxp_port_write(port, SCCNXP_CR_REG, CR_CMD_TX_RESET); 744 sccnxp_port_write(port, SCCNXP_CR_REG, CR_CMD_STATUS_RESET); 745 sccnxp_port_write(port, SCCNXP_CR_REG, CR_CMD_BREAK_RESET); 746 747 /* Enable RX & TX */ 748 sccnxp_port_write(port, SCCNXP_CR_REG, CR_RX_ENABLE | CR_TX_ENABLE); 749 750 /* Enable RX interrupt */ 751 sccnxp_enable_irq(port, IMR_RXRDY); 752 753 s->opened[port->line] = 1; 754 755 spin_unlock_irqrestore(&s->lock, flags); 756 757 return 0; 758 } 759 760 static void sccnxp_shutdown(struct uart_port *port) 761 { 762 struct sccnxp_port *s = dev_get_drvdata(port->dev); 763 unsigned long flags; 764 765 spin_lock_irqsave(&s->lock, flags); 766 767 s->opened[port->line] = 0; 768 769 /* Disable interrupts */ 770 sccnxp_disable_irq(port, IMR_TXRDY | IMR_RXRDY); 771 772 /* Disable TX & RX */ 773 sccnxp_port_write(port, SCCNXP_CR_REG, CR_RX_DISABLE | CR_TX_DISABLE); 774 775 /* Leave direction to input */ 776 if (s->chip->flags & SCCNXP_HAVE_IO) 777 sccnxp_set_bit(port, DIR_OP, 0); 778 779 spin_unlock_irqrestore(&s->lock, flags); 780 } 781 782 static const char *sccnxp_type(struct uart_port *port) 783 { 784 struct sccnxp_port *s = dev_get_drvdata(port->dev); 785 786 return (port->type == PORT_SC26XX) ? s->chip->name : NULL; 787 } 788 789 static void sccnxp_release_port(struct uart_port *port) 790 { 791 /* Do nothing */ 792 } 793 794 static int sccnxp_request_port(struct uart_port *port) 795 { 796 /* Do nothing */ 797 return 0; 798 } 799 800 static void sccnxp_config_port(struct uart_port *port, int flags) 801 { 802 if (flags & UART_CONFIG_TYPE) 803 port->type = PORT_SC26XX; 804 } 805 806 static int sccnxp_verify_port(struct uart_port *port, struct serial_struct *s) 807 { 808 if ((s->type == PORT_UNKNOWN) || (s->type == PORT_SC26XX)) 809 return 0; 810 if (s->irq == port->irq) 811 return 0; 812 813 return -EINVAL; 814 } 815 816 static const struct uart_ops sccnxp_ops = { 817 .tx_empty = sccnxp_tx_empty, 818 .set_mctrl = sccnxp_set_mctrl, 819 .get_mctrl = sccnxp_get_mctrl, 820 .stop_tx = sccnxp_stop_tx, 821 .start_tx = sccnxp_start_tx, 822 .stop_rx = sccnxp_stop_rx, 823 .break_ctl = sccnxp_break_ctl, 824 .startup = sccnxp_startup, 825 .shutdown = sccnxp_shutdown, 826 .set_termios = sccnxp_set_termios, 827 .type = sccnxp_type, 828 .release_port = sccnxp_release_port, 829 .request_port = sccnxp_request_port, 830 .config_port = sccnxp_config_port, 831 .verify_port = sccnxp_verify_port, 832 }; 833 834 #ifdef CONFIG_SERIAL_SCCNXP_CONSOLE 835 static void sccnxp_console_putchar(struct uart_port *port, int c) 836 { 837 int tryes = 100000; 838 839 while (tryes--) { 840 if (sccnxp_port_read(port, SCCNXP_SR_REG) & SR_TXRDY) { 841 sccnxp_port_write(port, SCCNXP_THR_REG, c); 842 break; 843 } 844 barrier(); 845 } 846 } 847 848 static void sccnxp_console_write(struct console *co, const char *c, unsigned n) 849 { 850 struct sccnxp_port *s = (struct sccnxp_port *)co->data; 851 struct uart_port *port = &s->port[co->index]; 852 unsigned long flags; 853 854 spin_lock_irqsave(&s->lock, flags); 855 uart_console_write(port, c, n, sccnxp_console_putchar); 856 spin_unlock_irqrestore(&s->lock, flags); 857 } 858 859 static int sccnxp_console_setup(struct console *co, char *options) 860 { 861 struct sccnxp_port *s = (struct sccnxp_port *)co->data; 862 struct uart_port *port = &s->port[(co->index > 0) ? co->index : 0]; 863 int baud = 9600, bits = 8, parity = 'n', flow = 'n'; 864 865 if (options) 866 uart_parse_options(options, &baud, &parity, &bits, &flow); 867 868 return uart_set_options(port, co, baud, parity, bits, flow); 869 } 870 #endif 871 872 static const struct platform_device_id sccnxp_id_table[] = { 873 { .name = "sc2681", .driver_data = (kernel_ulong_t)&sc2681, }, 874 { .name = "sc2691", .driver_data = (kernel_ulong_t)&sc2691, }, 875 { .name = "sc2692", .driver_data = (kernel_ulong_t)&sc2692, }, 876 { .name = "sc2891", .driver_data = (kernel_ulong_t)&sc2891, }, 877 { .name = "sc2892", .driver_data = (kernel_ulong_t)&sc2892, }, 878 { .name = "sc28202", .driver_data = (kernel_ulong_t)&sc28202, }, 879 { .name = "sc68681", .driver_data = (kernel_ulong_t)&sc68681, }, 880 { .name = "sc68692", .driver_data = (kernel_ulong_t)&sc68692, }, 881 { } 882 }; 883 MODULE_DEVICE_TABLE(platform, sccnxp_id_table); 884 885 static int sccnxp_probe(struct platform_device *pdev) 886 { 887 struct resource *res = platform_get_resource(pdev, IORESOURCE_MEM, 0); 888 struct sccnxp_pdata *pdata = dev_get_platdata(&pdev->dev); 889 int i, ret, uartclk; 890 struct sccnxp_port *s; 891 void __iomem *membase; 892 struct clk *clk; 893 894 membase = devm_ioremap_resource(&pdev->dev, res); 895 if (IS_ERR(membase)) 896 return PTR_ERR(membase); 897 898 s = devm_kzalloc(&pdev->dev, sizeof(struct sccnxp_port), GFP_KERNEL); 899 if (!s) { 900 dev_err(&pdev->dev, "Error allocating port structure\n"); 901 return -ENOMEM; 902 } 903 platform_set_drvdata(pdev, s); 904 905 spin_lock_init(&s->lock); 906 907 s->chip = (struct sccnxp_chip *)pdev->id_entry->driver_data; 908 909 s->regulator = devm_regulator_get(&pdev->dev, "vcc"); 910 if (!IS_ERR(s->regulator)) { 911 ret = regulator_enable(s->regulator); 912 if (ret) { 913 dev_err(&pdev->dev, 914 "Failed to enable regulator: %i\n", ret); 915 return ret; 916 } 917 } else if (PTR_ERR(s->regulator) == -EPROBE_DEFER) 918 return -EPROBE_DEFER; 919 920 clk = devm_clk_get(&pdev->dev, NULL); 921 if (IS_ERR(clk)) { 922 ret = PTR_ERR(clk); 923 if (ret == -EPROBE_DEFER) 924 goto err_out; 925 uartclk = 0; 926 } else { 927 ret = clk_prepare_enable(clk); 928 if (ret) 929 goto err_out; 930 931 ret = devm_add_action_or_reset(&pdev->dev, 932 (void(*)(void *))clk_disable_unprepare, 933 clk); 934 if (ret) 935 goto err_out; 936 937 uartclk = clk_get_rate(clk); 938 } 939 940 if (!uartclk) { 941 dev_notice(&pdev->dev, "Using default clock frequency\n"); 942 uartclk = s->chip->freq_std; 943 } 944 945 /* Check input frequency */ 946 if ((uartclk < s->chip->freq_min) || (uartclk > s->chip->freq_max)) { 947 dev_err(&pdev->dev, "Frequency out of bounds\n"); 948 ret = -EINVAL; 949 goto err_out; 950 } 951 952 if (pdata) 953 memcpy(&s->pdata, pdata, sizeof(struct sccnxp_pdata)); 954 955 if (s->pdata.poll_time_us) { 956 dev_info(&pdev->dev, "Using poll mode, resolution %u usecs\n", 957 s->pdata.poll_time_us); 958 s->poll = 1; 959 } 960 961 if (!s->poll) { 962 s->irq = platform_get_irq(pdev, 0); 963 if (s->irq < 0) { 964 dev_err(&pdev->dev, "Missing irq resource data\n"); 965 ret = -ENXIO; 966 goto err_out; 967 } 968 } 969 970 s->uart.owner = THIS_MODULE; 971 s->uart.dev_name = "ttySC"; 972 s->uart.major = SCCNXP_MAJOR; 973 s->uart.minor = SCCNXP_MINOR; 974 s->uart.nr = s->chip->nr; 975 #ifdef CONFIG_SERIAL_SCCNXP_CONSOLE 976 s->uart.cons = &s->console; 977 s->uart.cons->device = uart_console_device; 978 s->uart.cons->write = sccnxp_console_write; 979 s->uart.cons->setup = sccnxp_console_setup; 980 s->uart.cons->flags = CON_PRINTBUFFER; 981 s->uart.cons->index = -1; 982 s->uart.cons->data = s; 983 strcpy(s->uart.cons->name, "ttySC"); 984 #endif 985 ret = uart_register_driver(&s->uart); 986 if (ret) { 987 dev_err(&pdev->dev, "Registering UART driver failed\n"); 988 goto err_out; 989 } 990 991 for (i = 0; i < s->uart.nr; i++) { 992 s->port[i].line = i; 993 s->port[i].dev = &pdev->dev; 994 s->port[i].irq = s->irq; 995 s->port[i].type = PORT_SC26XX; 996 s->port[i].fifosize = s->chip->fifosize; 997 s->port[i].flags = UPF_SKIP_TEST | UPF_FIXED_TYPE; 998 s->port[i].iotype = UPIO_MEM; 999 s->port[i].mapbase = res->start; 1000 s->port[i].membase = membase; 1001 s->port[i].regshift = s->pdata.reg_shift; 1002 s->port[i].uartclk = uartclk; 1003 s->port[i].ops = &sccnxp_ops; 1004 uart_add_one_port(&s->uart, &s->port[i]); 1005 /* Set direction to input */ 1006 if (s->chip->flags & SCCNXP_HAVE_IO) 1007 sccnxp_set_bit(&s->port[i], DIR_OP, 0); 1008 } 1009 1010 /* Disable interrupts */ 1011 s->imr = 0; 1012 sccnxp_write(&s->port[0], SCCNXP_IMR_REG, 0); 1013 1014 if (!s->poll) { 1015 ret = devm_request_threaded_irq(&pdev->dev, s->irq, NULL, 1016 sccnxp_ist, 1017 IRQF_TRIGGER_FALLING | 1018 IRQF_ONESHOT, 1019 dev_name(&pdev->dev), s); 1020 if (!ret) 1021 return 0; 1022 1023 dev_err(&pdev->dev, "Unable to reguest IRQ %i\n", s->irq); 1024 } else { 1025 timer_setup(&s->timer, sccnxp_timer, 0); 1026 mod_timer(&s->timer, jiffies + 1027 usecs_to_jiffies(s->pdata.poll_time_us)); 1028 return 0; 1029 } 1030 1031 uart_unregister_driver(&s->uart); 1032 err_out: 1033 if (!IS_ERR(s->regulator)) 1034 regulator_disable(s->regulator); 1035 1036 return ret; 1037 } 1038 1039 static int sccnxp_remove(struct platform_device *pdev) 1040 { 1041 int i; 1042 struct sccnxp_port *s = platform_get_drvdata(pdev); 1043 1044 if (!s->poll) 1045 devm_free_irq(&pdev->dev, s->irq, s); 1046 else 1047 del_timer_sync(&s->timer); 1048 1049 for (i = 0; i < s->uart.nr; i++) 1050 uart_remove_one_port(&s->uart, &s->port[i]); 1051 1052 uart_unregister_driver(&s->uart); 1053 1054 if (!IS_ERR(s->regulator)) 1055 return regulator_disable(s->regulator); 1056 1057 return 0; 1058 } 1059 1060 static struct platform_driver sccnxp_uart_driver = { 1061 .driver = { 1062 .name = SCCNXP_NAME, 1063 }, 1064 .probe = sccnxp_probe, 1065 .remove = sccnxp_remove, 1066 .id_table = sccnxp_id_table, 1067 }; 1068 module_platform_driver(sccnxp_uart_driver); 1069 1070 MODULE_LICENSE("GPL v2"); 1071 MODULE_AUTHOR("Alexander Shiyan <shc_work@mail.ru>"); 1072 MODULE_DESCRIPTION("SCCNXP serial driver"); 1073