1 // SPDX-License-Identifier: GPL-2.0+ 2 /* 3 * SC16IS7xx tty serial driver - Copyright (C) 2014 GridPoint 4 * Author: Jon Ringle <jringle@gridpoint.com> 5 * 6 * Based on max310x.c, by Alexander Shiyan <shc_work@mail.ru> 7 */ 8 9 #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt 10 11 #include <linux/bitops.h> 12 #include <linux/clk.h> 13 #include <linux/delay.h> 14 #include <linux/device.h> 15 #include <linux/gpio/driver.h> 16 #include <linux/i2c.h> 17 #include <linux/module.h> 18 #include <linux/of.h> 19 #include <linux/of_device.h> 20 #include <linux/regmap.h> 21 #include <linux/serial_core.h> 22 #include <linux/serial.h> 23 #include <linux/tty.h> 24 #include <linux/tty_flip.h> 25 #include <linux/spi/spi.h> 26 #include <linux/uaccess.h> 27 #include <uapi/linux/sched/types.h> 28 29 #define SC16IS7XX_NAME "sc16is7xx" 30 #define SC16IS7XX_MAX_DEVS 8 31 32 /* SC16IS7XX register definitions */ 33 #define SC16IS7XX_RHR_REG (0x00) /* RX FIFO */ 34 #define SC16IS7XX_THR_REG (0x00) /* TX FIFO */ 35 #define SC16IS7XX_IER_REG (0x01) /* Interrupt enable */ 36 #define SC16IS7XX_IIR_REG (0x02) /* Interrupt Identification */ 37 #define SC16IS7XX_FCR_REG (0x02) /* FIFO control */ 38 #define SC16IS7XX_LCR_REG (0x03) /* Line Control */ 39 #define SC16IS7XX_MCR_REG (0x04) /* Modem Control */ 40 #define SC16IS7XX_LSR_REG (0x05) /* Line Status */ 41 #define SC16IS7XX_MSR_REG (0x06) /* Modem Status */ 42 #define SC16IS7XX_SPR_REG (0x07) /* Scratch Pad */ 43 #define SC16IS7XX_TXLVL_REG (0x08) /* TX FIFO level */ 44 #define SC16IS7XX_RXLVL_REG (0x09) /* RX FIFO level */ 45 #define SC16IS7XX_IODIR_REG (0x0a) /* I/O Direction 46 * - only on 75x/76x 47 */ 48 #define SC16IS7XX_IOSTATE_REG (0x0b) /* I/O State 49 * - only on 75x/76x 50 */ 51 #define SC16IS7XX_IOINTENA_REG (0x0c) /* I/O Interrupt Enable 52 * - only on 75x/76x 53 */ 54 #define SC16IS7XX_IOCONTROL_REG (0x0e) /* I/O Control 55 * - only on 75x/76x 56 */ 57 #define SC16IS7XX_EFCR_REG (0x0f) /* Extra Features Control */ 58 59 /* TCR/TLR Register set: Only if ((MCR[2] == 1) && (EFR[4] == 1)) */ 60 #define SC16IS7XX_TCR_REG (0x06) /* Transmit control */ 61 #define SC16IS7XX_TLR_REG (0x07) /* Trigger level */ 62 63 /* Special Register set: Only if ((LCR[7] == 1) && (LCR != 0xBF)) */ 64 #define SC16IS7XX_DLL_REG (0x00) /* Divisor Latch Low */ 65 #define SC16IS7XX_DLH_REG (0x01) /* Divisor Latch High */ 66 67 /* Enhanced Register set: Only if (LCR == 0xBF) */ 68 #define SC16IS7XX_EFR_REG (0x02) /* Enhanced Features */ 69 #define SC16IS7XX_XON1_REG (0x04) /* Xon1 word */ 70 #define SC16IS7XX_XON2_REG (0x05) /* Xon2 word */ 71 #define SC16IS7XX_XOFF1_REG (0x06) /* Xoff1 word */ 72 #define SC16IS7XX_XOFF2_REG (0x07) /* Xoff2 word */ 73 74 /* IER register bits */ 75 #define SC16IS7XX_IER_RDI_BIT (1 << 0) /* Enable RX data interrupt */ 76 #define SC16IS7XX_IER_THRI_BIT (1 << 1) /* Enable TX holding register 77 * interrupt */ 78 #define SC16IS7XX_IER_RLSI_BIT (1 << 2) /* Enable RX line status 79 * interrupt */ 80 #define SC16IS7XX_IER_MSI_BIT (1 << 3) /* Enable Modem status 81 * interrupt */ 82 83 /* IER register bits - write only if (EFR[4] == 1) */ 84 #define SC16IS7XX_IER_SLEEP_BIT (1 << 4) /* Enable Sleep mode */ 85 #define SC16IS7XX_IER_XOFFI_BIT (1 << 5) /* Enable Xoff interrupt */ 86 #define SC16IS7XX_IER_RTSI_BIT (1 << 6) /* Enable nRTS interrupt */ 87 #define SC16IS7XX_IER_CTSI_BIT (1 << 7) /* Enable nCTS interrupt */ 88 89 /* FCR register bits */ 90 #define SC16IS7XX_FCR_FIFO_BIT (1 << 0) /* Enable FIFO */ 91 #define SC16IS7XX_FCR_RXRESET_BIT (1 << 1) /* Reset RX FIFO */ 92 #define SC16IS7XX_FCR_TXRESET_BIT (1 << 2) /* Reset TX FIFO */ 93 #define SC16IS7XX_FCR_RXLVLL_BIT (1 << 6) /* RX Trigger level LSB */ 94 #define SC16IS7XX_FCR_RXLVLH_BIT (1 << 7) /* RX Trigger level MSB */ 95 96 /* FCR register bits - write only if (EFR[4] == 1) */ 97 #define SC16IS7XX_FCR_TXLVLL_BIT (1 << 4) /* TX Trigger level LSB */ 98 #define SC16IS7XX_FCR_TXLVLH_BIT (1 << 5) /* TX Trigger level MSB */ 99 100 /* IIR register bits */ 101 #define SC16IS7XX_IIR_NO_INT_BIT (1 << 0) /* No interrupts pending */ 102 #define SC16IS7XX_IIR_ID_MASK 0x3e /* Mask for the interrupt ID */ 103 #define SC16IS7XX_IIR_THRI_SRC 0x02 /* TX holding register empty */ 104 #define SC16IS7XX_IIR_RDI_SRC 0x04 /* RX data interrupt */ 105 #define SC16IS7XX_IIR_RLSE_SRC 0x06 /* RX line status error */ 106 #define SC16IS7XX_IIR_RTOI_SRC 0x0c /* RX time-out interrupt */ 107 #define SC16IS7XX_IIR_MSI_SRC 0x00 /* Modem status interrupt 108 * - only on 75x/76x 109 */ 110 #define SC16IS7XX_IIR_INPIN_SRC 0x30 /* Input pin change of state 111 * - only on 75x/76x 112 */ 113 #define SC16IS7XX_IIR_XOFFI_SRC 0x10 /* Received Xoff */ 114 #define SC16IS7XX_IIR_CTSRTS_SRC 0x20 /* nCTS,nRTS change of state 115 * from active (LOW) 116 * to inactive (HIGH) 117 */ 118 /* LCR register bits */ 119 #define SC16IS7XX_LCR_LENGTH0_BIT (1 << 0) /* Word length bit 0 */ 120 #define SC16IS7XX_LCR_LENGTH1_BIT (1 << 1) /* Word length bit 1 121 * 122 * Word length bits table: 123 * 00 -> 5 bit words 124 * 01 -> 6 bit words 125 * 10 -> 7 bit words 126 * 11 -> 8 bit words 127 */ 128 #define SC16IS7XX_LCR_STOPLEN_BIT (1 << 2) /* STOP length bit 129 * 130 * STOP length bit table: 131 * 0 -> 1 stop bit 132 * 1 -> 1-1.5 stop bits if 133 * word length is 5, 134 * 2 stop bits otherwise 135 */ 136 #define SC16IS7XX_LCR_PARITY_BIT (1 << 3) /* Parity bit enable */ 137 #define SC16IS7XX_LCR_EVENPARITY_BIT (1 << 4) /* Even parity bit enable */ 138 #define SC16IS7XX_LCR_FORCEPARITY_BIT (1 << 5) /* 9-bit multidrop parity */ 139 #define SC16IS7XX_LCR_TXBREAK_BIT (1 << 6) /* TX break enable */ 140 #define SC16IS7XX_LCR_DLAB_BIT (1 << 7) /* Divisor Latch enable */ 141 #define SC16IS7XX_LCR_WORD_LEN_5 (0x00) 142 #define SC16IS7XX_LCR_WORD_LEN_6 (0x01) 143 #define SC16IS7XX_LCR_WORD_LEN_7 (0x02) 144 #define SC16IS7XX_LCR_WORD_LEN_8 (0x03) 145 #define SC16IS7XX_LCR_CONF_MODE_A SC16IS7XX_LCR_DLAB_BIT /* Special 146 * reg set */ 147 #define SC16IS7XX_LCR_CONF_MODE_B 0xBF /* Enhanced 148 * reg set */ 149 150 /* MCR register bits */ 151 #define SC16IS7XX_MCR_DTR_BIT (1 << 0) /* DTR complement 152 * - only on 75x/76x 153 */ 154 #define SC16IS7XX_MCR_RTS_BIT (1 << 1) /* RTS complement */ 155 #define SC16IS7XX_MCR_TCRTLR_BIT (1 << 2) /* TCR/TLR register enable */ 156 #define SC16IS7XX_MCR_LOOP_BIT (1 << 4) /* Enable loopback test mode */ 157 #define SC16IS7XX_MCR_XONANY_BIT (1 << 5) /* Enable Xon Any 158 * - write enabled 159 * if (EFR[4] == 1) 160 */ 161 #define SC16IS7XX_MCR_IRDA_BIT (1 << 6) /* Enable IrDA mode 162 * - write enabled 163 * if (EFR[4] == 1) 164 */ 165 #define SC16IS7XX_MCR_CLKSEL_BIT (1 << 7) /* Divide clock by 4 166 * - write enabled 167 * if (EFR[4] == 1) 168 */ 169 170 /* LSR register bits */ 171 #define SC16IS7XX_LSR_DR_BIT (1 << 0) /* Receiver data ready */ 172 #define SC16IS7XX_LSR_OE_BIT (1 << 1) /* Overrun Error */ 173 #define SC16IS7XX_LSR_PE_BIT (1 << 2) /* Parity Error */ 174 #define SC16IS7XX_LSR_FE_BIT (1 << 3) /* Frame Error */ 175 #define SC16IS7XX_LSR_BI_BIT (1 << 4) /* Break Interrupt */ 176 #define SC16IS7XX_LSR_BRK_ERROR_MASK 0x1E /* BI, FE, PE, OE bits */ 177 #define SC16IS7XX_LSR_THRE_BIT (1 << 5) /* TX holding register empty */ 178 #define SC16IS7XX_LSR_TEMT_BIT (1 << 6) /* Transmitter empty */ 179 #define SC16IS7XX_LSR_FIFOE_BIT (1 << 7) /* Fifo Error */ 180 181 /* MSR register bits */ 182 #define SC16IS7XX_MSR_DCTS_BIT (1 << 0) /* Delta CTS Clear To Send */ 183 #define SC16IS7XX_MSR_DDSR_BIT (1 << 1) /* Delta DSR Data Set Ready 184 * or (IO4) 185 * - only on 75x/76x 186 */ 187 #define SC16IS7XX_MSR_DRI_BIT (1 << 2) /* Delta RI Ring Indicator 188 * or (IO7) 189 * - only on 75x/76x 190 */ 191 #define SC16IS7XX_MSR_DCD_BIT (1 << 3) /* Delta CD Carrier Detect 192 * or (IO6) 193 * - only on 75x/76x 194 */ 195 #define SC16IS7XX_MSR_CTS_BIT (1 << 4) /* CTS */ 196 #define SC16IS7XX_MSR_DSR_BIT (1 << 5) /* DSR (IO4) 197 * - only on 75x/76x 198 */ 199 #define SC16IS7XX_MSR_RI_BIT (1 << 6) /* RI (IO7) 200 * - only on 75x/76x 201 */ 202 #define SC16IS7XX_MSR_CD_BIT (1 << 7) /* CD (IO6) 203 * - only on 75x/76x 204 */ 205 #define SC16IS7XX_MSR_DELTA_MASK 0x0F /* Any of the delta bits! */ 206 207 /* 208 * TCR register bits 209 * TCR trigger levels are available from 0 to 60 characters with a granularity 210 * of four. 211 * The programmer must program the TCR such that TCR[3:0] > TCR[7:4]. There is 212 * no built-in hardware check to make sure this condition is met. Also, the TCR 213 * must be programmed with this condition before auto RTS or software flow 214 * control is enabled to avoid spurious operation of the device. 215 */ 216 #define SC16IS7XX_TCR_RX_HALT(words) ((((words) / 4) & 0x0f) << 0) 217 #define SC16IS7XX_TCR_RX_RESUME(words) ((((words) / 4) & 0x0f) << 4) 218 219 /* 220 * TLR register bits 221 * If TLR[3:0] or TLR[7:4] are logical 0, the selectable trigger levels via the 222 * FIFO Control Register (FCR) are used for the transmit and receive FIFO 223 * trigger levels. Trigger levels from 4 characters to 60 characters are 224 * available with a granularity of four. 225 * 226 * When the trigger level setting in TLR is zero, the SC16IS740/750/760 uses the 227 * trigger level setting defined in FCR. If TLR has non-zero trigger level value 228 * the trigger level defined in FCR is discarded. This applies to both transmit 229 * FIFO and receive FIFO trigger level setting. 230 * 231 * When TLR is used for RX trigger level control, FCR[7:6] should be left at the 232 * default state, that is, '00'. 233 */ 234 #define SC16IS7XX_TLR_TX_TRIGGER(words) ((((words) / 4) & 0x0f) << 0) 235 #define SC16IS7XX_TLR_RX_TRIGGER(words) ((((words) / 4) & 0x0f) << 4) 236 237 /* IOControl register bits (Only 750/760) */ 238 #define SC16IS7XX_IOCONTROL_LATCH_BIT (1 << 0) /* Enable input latching */ 239 #define SC16IS7XX_IOCONTROL_MODEM_BIT (1 << 1) /* Enable GPIO[7:4] as modem pins */ 240 #define SC16IS7XX_IOCONTROL_SRESET_BIT (1 << 3) /* Software Reset */ 241 242 /* EFCR register bits */ 243 #define SC16IS7XX_EFCR_9BIT_MODE_BIT (1 << 0) /* Enable 9-bit or Multidrop 244 * mode (RS485) */ 245 #define SC16IS7XX_EFCR_RXDISABLE_BIT (1 << 1) /* Disable receiver */ 246 #define SC16IS7XX_EFCR_TXDISABLE_BIT (1 << 2) /* Disable transmitter */ 247 #define SC16IS7XX_EFCR_AUTO_RS485_BIT (1 << 4) /* Auto RS485 RTS direction */ 248 #define SC16IS7XX_EFCR_RTS_INVERT_BIT (1 << 5) /* RTS output inversion */ 249 #define SC16IS7XX_EFCR_IRDA_MODE_BIT (1 << 7) /* IrDA mode 250 * 0 = rate upto 115.2 kbit/s 251 * - Only 750/760 252 * 1 = rate upto 1.152 Mbit/s 253 * - Only 760 254 */ 255 256 /* EFR register bits */ 257 #define SC16IS7XX_EFR_AUTORTS_BIT (1 << 6) /* Auto RTS flow ctrl enable */ 258 #define SC16IS7XX_EFR_AUTOCTS_BIT (1 << 7) /* Auto CTS flow ctrl enable */ 259 #define SC16IS7XX_EFR_XOFF2_DETECT_BIT (1 << 5) /* Enable Xoff2 detection */ 260 #define SC16IS7XX_EFR_ENABLE_BIT (1 << 4) /* Enable enhanced functions 261 * and writing to IER[7:4], 262 * FCR[5:4], MCR[7:5] 263 */ 264 #define SC16IS7XX_EFR_SWFLOW3_BIT (1 << 3) /* SWFLOW bit 3 */ 265 #define SC16IS7XX_EFR_SWFLOW2_BIT (1 << 2) /* SWFLOW bit 2 266 * 267 * SWFLOW bits 3 & 2 table: 268 * 00 -> no transmitter flow 269 * control 270 * 01 -> transmitter generates 271 * XON2 and XOFF2 272 * 10 -> transmitter generates 273 * XON1 and XOFF1 274 * 11 -> transmitter generates 275 * XON1, XON2, XOFF1 and 276 * XOFF2 277 */ 278 #define SC16IS7XX_EFR_SWFLOW1_BIT (1 << 1) /* SWFLOW bit 2 */ 279 #define SC16IS7XX_EFR_SWFLOW0_BIT (1 << 0) /* SWFLOW bit 3 280 * 281 * SWFLOW bits 3 & 2 table: 282 * 00 -> no received flow 283 * control 284 * 01 -> receiver compares 285 * XON2 and XOFF2 286 * 10 -> receiver compares 287 * XON1 and XOFF1 288 * 11 -> receiver compares 289 * XON1, XON2, XOFF1 and 290 * XOFF2 291 */ 292 293 /* Misc definitions */ 294 #define SC16IS7XX_FIFO_SIZE (64) 295 #define SC16IS7XX_REG_SHIFT 2 296 297 struct sc16is7xx_devtype { 298 char name[10]; 299 int nr_gpio; 300 int nr_uart; 301 }; 302 303 #define SC16IS7XX_RECONF_MD (1 << 0) 304 #define SC16IS7XX_RECONF_IER (1 << 1) 305 #define SC16IS7XX_RECONF_RS485 (1 << 2) 306 307 struct sc16is7xx_one_config { 308 unsigned int flags; 309 u8 ier_clear; 310 }; 311 312 struct sc16is7xx_one { 313 struct uart_port port; 314 u8 line; 315 struct kthread_work tx_work; 316 struct kthread_work reg_work; 317 struct sc16is7xx_one_config config; 318 }; 319 320 struct sc16is7xx_port { 321 const struct sc16is7xx_devtype *devtype; 322 struct regmap *regmap; 323 struct clk *clk; 324 #ifdef CONFIG_GPIOLIB 325 struct gpio_chip gpio; 326 #endif 327 unsigned char buf[SC16IS7XX_FIFO_SIZE]; 328 struct kthread_worker kworker; 329 struct task_struct *kworker_task; 330 struct kthread_work irq_work; 331 struct sc16is7xx_one p[0]; 332 }; 333 334 static unsigned long sc16is7xx_lines; 335 336 static struct uart_driver sc16is7xx_uart = { 337 .owner = THIS_MODULE, 338 .dev_name = "ttySC", 339 .nr = SC16IS7XX_MAX_DEVS, 340 }; 341 342 #define to_sc16is7xx_port(p,e) ((container_of((p), struct sc16is7xx_port, e))) 343 #define to_sc16is7xx_one(p,e) ((container_of((p), struct sc16is7xx_one, e))) 344 345 static int sc16is7xx_line(struct uart_port *port) 346 { 347 struct sc16is7xx_one *one = to_sc16is7xx_one(port, port); 348 349 return one->line; 350 } 351 352 static u8 sc16is7xx_port_read(struct uart_port *port, u8 reg) 353 { 354 struct sc16is7xx_port *s = dev_get_drvdata(port->dev); 355 unsigned int val = 0; 356 const u8 line = sc16is7xx_line(port); 357 358 regmap_read(s->regmap, (reg << SC16IS7XX_REG_SHIFT) | line, &val); 359 360 return val; 361 } 362 363 static void sc16is7xx_port_write(struct uart_port *port, u8 reg, u8 val) 364 { 365 struct sc16is7xx_port *s = dev_get_drvdata(port->dev); 366 const u8 line = sc16is7xx_line(port); 367 368 regmap_write(s->regmap, (reg << SC16IS7XX_REG_SHIFT) | line, val); 369 } 370 371 static void sc16is7xx_fifo_read(struct uart_port *port, unsigned int rxlen) 372 { 373 struct sc16is7xx_port *s = dev_get_drvdata(port->dev); 374 const u8 line = sc16is7xx_line(port); 375 u8 addr = (SC16IS7XX_RHR_REG << SC16IS7XX_REG_SHIFT) | line; 376 377 regcache_cache_bypass(s->regmap, true); 378 regmap_raw_read(s->regmap, addr, s->buf, rxlen); 379 regcache_cache_bypass(s->regmap, false); 380 } 381 382 static void sc16is7xx_fifo_write(struct uart_port *port, u8 to_send) 383 { 384 struct sc16is7xx_port *s = dev_get_drvdata(port->dev); 385 const u8 line = sc16is7xx_line(port); 386 u8 addr = (SC16IS7XX_THR_REG << SC16IS7XX_REG_SHIFT) | line; 387 388 /* 389 * Don't send zero-length data, at least on SPI it confuses the chip 390 * delivering wrong TXLVL data. 391 */ 392 if (unlikely(!to_send)) 393 return; 394 395 regcache_cache_bypass(s->regmap, true); 396 regmap_raw_write(s->regmap, addr, s->buf, to_send); 397 regcache_cache_bypass(s->regmap, false); 398 } 399 400 static void sc16is7xx_port_update(struct uart_port *port, u8 reg, 401 u8 mask, u8 val) 402 { 403 struct sc16is7xx_port *s = dev_get_drvdata(port->dev); 404 const u8 line = sc16is7xx_line(port); 405 406 regmap_update_bits(s->regmap, (reg << SC16IS7XX_REG_SHIFT) | line, 407 mask, val); 408 } 409 410 static int sc16is7xx_alloc_line(void) 411 { 412 int i; 413 414 BUILD_BUG_ON(SC16IS7XX_MAX_DEVS > BITS_PER_LONG); 415 416 for (i = 0; i < SC16IS7XX_MAX_DEVS; i++) 417 if (!test_and_set_bit(i, &sc16is7xx_lines)) 418 break; 419 420 return i; 421 } 422 423 static void sc16is7xx_power(struct uart_port *port, int on) 424 { 425 sc16is7xx_port_update(port, SC16IS7XX_IER_REG, 426 SC16IS7XX_IER_SLEEP_BIT, 427 on ? 0 : SC16IS7XX_IER_SLEEP_BIT); 428 } 429 430 static const struct sc16is7xx_devtype sc16is74x_devtype = { 431 .name = "SC16IS74X", 432 .nr_gpio = 0, 433 .nr_uart = 1, 434 }; 435 436 static const struct sc16is7xx_devtype sc16is750_devtype = { 437 .name = "SC16IS750", 438 .nr_gpio = 8, 439 .nr_uart = 1, 440 }; 441 442 static const struct sc16is7xx_devtype sc16is752_devtype = { 443 .name = "SC16IS752", 444 .nr_gpio = 8, 445 .nr_uart = 2, 446 }; 447 448 static const struct sc16is7xx_devtype sc16is760_devtype = { 449 .name = "SC16IS760", 450 .nr_gpio = 8, 451 .nr_uart = 1, 452 }; 453 454 static const struct sc16is7xx_devtype sc16is762_devtype = { 455 .name = "SC16IS762", 456 .nr_gpio = 8, 457 .nr_uart = 2, 458 }; 459 460 static bool sc16is7xx_regmap_volatile(struct device *dev, unsigned int reg) 461 { 462 switch (reg >> SC16IS7XX_REG_SHIFT) { 463 case SC16IS7XX_RHR_REG: 464 case SC16IS7XX_IIR_REG: 465 case SC16IS7XX_LSR_REG: 466 case SC16IS7XX_MSR_REG: 467 case SC16IS7XX_TXLVL_REG: 468 case SC16IS7XX_RXLVL_REG: 469 case SC16IS7XX_IOSTATE_REG: 470 return true; 471 default: 472 break; 473 } 474 475 return false; 476 } 477 478 static bool sc16is7xx_regmap_precious(struct device *dev, unsigned int reg) 479 { 480 switch (reg >> SC16IS7XX_REG_SHIFT) { 481 case SC16IS7XX_RHR_REG: 482 return true; 483 default: 484 break; 485 } 486 487 return false; 488 } 489 490 static int sc16is7xx_set_baud(struct uart_port *port, int baud) 491 { 492 struct sc16is7xx_port *s = dev_get_drvdata(port->dev); 493 u8 lcr; 494 u8 prescaler = 0; 495 unsigned long clk = port->uartclk, div = clk / 16 / baud; 496 497 if (div > 0xffff) { 498 prescaler = SC16IS7XX_MCR_CLKSEL_BIT; 499 div /= 4; 500 } 501 502 lcr = sc16is7xx_port_read(port, SC16IS7XX_LCR_REG); 503 504 /* Open the LCR divisors for configuration */ 505 sc16is7xx_port_write(port, SC16IS7XX_LCR_REG, 506 SC16IS7XX_LCR_CONF_MODE_B); 507 508 /* Enable enhanced features */ 509 regcache_cache_bypass(s->regmap, true); 510 sc16is7xx_port_write(port, SC16IS7XX_EFR_REG, 511 SC16IS7XX_EFR_ENABLE_BIT); 512 regcache_cache_bypass(s->regmap, false); 513 514 /* Put LCR back to the normal mode */ 515 sc16is7xx_port_write(port, SC16IS7XX_LCR_REG, lcr); 516 517 sc16is7xx_port_update(port, SC16IS7XX_MCR_REG, 518 SC16IS7XX_MCR_CLKSEL_BIT, 519 prescaler); 520 521 /* Open the LCR divisors for configuration */ 522 sc16is7xx_port_write(port, SC16IS7XX_LCR_REG, 523 SC16IS7XX_LCR_CONF_MODE_A); 524 525 /* Write the new divisor */ 526 regcache_cache_bypass(s->regmap, true); 527 sc16is7xx_port_write(port, SC16IS7XX_DLH_REG, div / 256); 528 sc16is7xx_port_write(port, SC16IS7XX_DLL_REG, div % 256); 529 regcache_cache_bypass(s->regmap, false); 530 531 /* Put LCR back to the normal mode */ 532 sc16is7xx_port_write(port, SC16IS7XX_LCR_REG, lcr); 533 534 return DIV_ROUND_CLOSEST(clk / 16, div); 535 } 536 537 static void sc16is7xx_handle_rx(struct uart_port *port, unsigned int rxlen, 538 unsigned int iir) 539 { 540 struct sc16is7xx_port *s = dev_get_drvdata(port->dev); 541 unsigned int lsr = 0, ch, flag, bytes_read, i; 542 bool read_lsr = (iir == SC16IS7XX_IIR_RLSE_SRC) ? true : false; 543 544 if (unlikely(rxlen >= sizeof(s->buf))) { 545 dev_warn_ratelimited(port->dev, 546 "ttySC%i: Possible RX FIFO overrun: %d\n", 547 port->line, rxlen); 548 port->icount.buf_overrun++; 549 /* Ensure sanity of RX level */ 550 rxlen = sizeof(s->buf); 551 } 552 553 while (rxlen) { 554 /* Only read lsr if there are possible errors in FIFO */ 555 if (read_lsr) { 556 lsr = sc16is7xx_port_read(port, SC16IS7XX_LSR_REG); 557 if (!(lsr & SC16IS7XX_LSR_FIFOE_BIT)) 558 read_lsr = false; /* No errors left in FIFO */ 559 } else 560 lsr = 0; 561 562 if (read_lsr) { 563 s->buf[0] = sc16is7xx_port_read(port, SC16IS7XX_RHR_REG); 564 bytes_read = 1; 565 } else { 566 sc16is7xx_fifo_read(port, rxlen); 567 bytes_read = rxlen; 568 } 569 570 lsr &= SC16IS7XX_LSR_BRK_ERROR_MASK; 571 572 port->icount.rx++; 573 flag = TTY_NORMAL; 574 575 if (unlikely(lsr)) { 576 if (lsr & SC16IS7XX_LSR_BI_BIT) { 577 port->icount.brk++; 578 if (uart_handle_break(port)) 579 continue; 580 } else if (lsr & SC16IS7XX_LSR_PE_BIT) 581 port->icount.parity++; 582 else if (lsr & SC16IS7XX_LSR_FE_BIT) 583 port->icount.frame++; 584 else if (lsr & SC16IS7XX_LSR_OE_BIT) 585 port->icount.overrun++; 586 587 lsr &= port->read_status_mask; 588 if (lsr & SC16IS7XX_LSR_BI_BIT) 589 flag = TTY_BREAK; 590 else if (lsr & SC16IS7XX_LSR_PE_BIT) 591 flag = TTY_PARITY; 592 else if (lsr & SC16IS7XX_LSR_FE_BIT) 593 flag = TTY_FRAME; 594 else if (lsr & SC16IS7XX_LSR_OE_BIT) 595 flag = TTY_OVERRUN; 596 } 597 598 for (i = 0; i < bytes_read; ++i) { 599 ch = s->buf[i]; 600 if (uart_handle_sysrq_char(port, ch)) 601 continue; 602 603 if (lsr & port->ignore_status_mask) 604 continue; 605 606 uart_insert_char(port, lsr, SC16IS7XX_LSR_OE_BIT, ch, 607 flag); 608 } 609 rxlen -= bytes_read; 610 } 611 612 tty_flip_buffer_push(&port->state->port); 613 } 614 615 static void sc16is7xx_handle_tx(struct uart_port *port) 616 { 617 struct sc16is7xx_port *s = dev_get_drvdata(port->dev); 618 struct circ_buf *xmit = &port->state->xmit; 619 unsigned int txlen, to_send, i; 620 621 if (unlikely(port->x_char)) { 622 sc16is7xx_port_write(port, SC16IS7XX_THR_REG, port->x_char); 623 port->icount.tx++; 624 port->x_char = 0; 625 return; 626 } 627 628 if (uart_circ_empty(xmit) || uart_tx_stopped(port)) 629 return; 630 631 /* Get length of data pending in circular buffer */ 632 to_send = uart_circ_chars_pending(xmit); 633 if (likely(to_send)) { 634 /* Limit to size of TX FIFO */ 635 txlen = sc16is7xx_port_read(port, SC16IS7XX_TXLVL_REG); 636 if (txlen > SC16IS7XX_FIFO_SIZE) { 637 dev_err_ratelimited(port->dev, 638 "chip reports %d free bytes in TX fifo, but it only has %d", 639 txlen, SC16IS7XX_FIFO_SIZE); 640 txlen = 0; 641 } 642 to_send = (to_send > txlen) ? txlen : to_send; 643 644 /* Add data to send */ 645 port->icount.tx += to_send; 646 647 /* Convert to linear buffer */ 648 for (i = 0; i < to_send; ++i) { 649 s->buf[i] = xmit->buf[xmit->tail]; 650 xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1); 651 } 652 653 sc16is7xx_fifo_write(port, to_send); 654 } 655 656 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) 657 uart_write_wakeup(port); 658 } 659 660 static void sc16is7xx_port_irq(struct sc16is7xx_port *s, int portno) 661 { 662 struct uart_port *port = &s->p[portno].port; 663 664 do { 665 unsigned int iir, rxlen; 666 667 iir = sc16is7xx_port_read(port, SC16IS7XX_IIR_REG); 668 if (iir & SC16IS7XX_IIR_NO_INT_BIT) 669 break; 670 671 iir &= SC16IS7XX_IIR_ID_MASK; 672 673 switch (iir) { 674 case SC16IS7XX_IIR_RDI_SRC: 675 case SC16IS7XX_IIR_RLSE_SRC: 676 case SC16IS7XX_IIR_RTOI_SRC: 677 case SC16IS7XX_IIR_XOFFI_SRC: 678 rxlen = sc16is7xx_port_read(port, SC16IS7XX_RXLVL_REG); 679 if (rxlen) 680 sc16is7xx_handle_rx(port, rxlen, iir); 681 break; 682 case SC16IS7XX_IIR_THRI_SRC: 683 sc16is7xx_handle_tx(port); 684 break; 685 default: 686 dev_err_ratelimited(port->dev, 687 "ttySC%i: Unexpected interrupt: %x", 688 port->line, iir); 689 break; 690 } 691 } while (1); 692 } 693 694 static void sc16is7xx_ist(struct kthread_work *ws) 695 { 696 struct sc16is7xx_port *s = to_sc16is7xx_port(ws, irq_work); 697 int i; 698 699 for (i = 0; i < s->devtype->nr_uart; ++i) 700 sc16is7xx_port_irq(s, i); 701 } 702 703 static irqreturn_t sc16is7xx_irq(int irq, void *dev_id) 704 { 705 struct sc16is7xx_port *s = (struct sc16is7xx_port *)dev_id; 706 707 kthread_queue_work(&s->kworker, &s->irq_work); 708 709 return IRQ_HANDLED; 710 } 711 712 static void sc16is7xx_tx_proc(struct kthread_work *ws) 713 { 714 struct uart_port *port = &(to_sc16is7xx_one(ws, tx_work)->port); 715 716 if ((port->rs485.flags & SER_RS485_ENABLED) && 717 (port->rs485.delay_rts_before_send > 0)) 718 msleep(port->rs485.delay_rts_before_send); 719 720 sc16is7xx_handle_tx(port); 721 } 722 723 static void sc16is7xx_reconf_rs485(struct uart_port *port) 724 { 725 const u32 mask = SC16IS7XX_EFCR_AUTO_RS485_BIT | 726 SC16IS7XX_EFCR_RTS_INVERT_BIT; 727 u32 efcr = 0; 728 struct serial_rs485 *rs485 = &port->rs485; 729 unsigned long irqflags; 730 731 spin_lock_irqsave(&port->lock, irqflags); 732 if (rs485->flags & SER_RS485_ENABLED) { 733 efcr |= SC16IS7XX_EFCR_AUTO_RS485_BIT; 734 735 if (rs485->flags & SER_RS485_RTS_AFTER_SEND) 736 efcr |= SC16IS7XX_EFCR_RTS_INVERT_BIT; 737 } 738 spin_unlock_irqrestore(&port->lock, irqflags); 739 740 sc16is7xx_port_update(port, SC16IS7XX_EFCR_REG, mask, efcr); 741 } 742 743 static void sc16is7xx_reg_proc(struct kthread_work *ws) 744 { 745 struct sc16is7xx_one *one = to_sc16is7xx_one(ws, reg_work); 746 struct sc16is7xx_one_config config; 747 unsigned long irqflags; 748 749 spin_lock_irqsave(&one->port.lock, irqflags); 750 config = one->config; 751 memset(&one->config, 0, sizeof(one->config)); 752 spin_unlock_irqrestore(&one->port.lock, irqflags); 753 754 if (config.flags & SC16IS7XX_RECONF_MD) { 755 sc16is7xx_port_update(&one->port, SC16IS7XX_MCR_REG, 756 SC16IS7XX_MCR_LOOP_BIT, 757 (one->port.mctrl & TIOCM_LOOP) ? 758 SC16IS7XX_MCR_LOOP_BIT : 0); 759 sc16is7xx_port_update(&one->port, SC16IS7XX_MCR_REG, 760 SC16IS7XX_MCR_RTS_BIT, 761 (one->port.mctrl & TIOCM_RTS) ? 762 SC16IS7XX_MCR_RTS_BIT : 0); 763 sc16is7xx_port_update(&one->port, SC16IS7XX_MCR_REG, 764 SC16IS7XX_MCR_DTR_BIT, 765 (one->port.mctrl & TIOCM_DTR) ? 766 SC16IS7XX_MCR_DTR_BIT : 0); 767 } 768 if (config.flags & SC16IS7XX_RECONF_IER) 769 sc16is7xx_port_update(&one->port, SC16IS7XX_IER_REG, 770 config.ier_clear, 0); 771 772 if (config.flags & SC16IS7XX_RECONF_RS485) 773 sc16is7xx_reconf_rs485(&one->port); 774 } 775 776 static void sc16is7xx_ier_clear(struct uart_port *port, u8 bit) 777 { 778 struct sc16is7xx_port *s = dev_get_drvdata(port->dev); 779 struct sc16is7xx_one *one = to_sc16is7xx_one(port, port); 780 781 one->config.flags |= SC16IS7XX_RECONF_IER; 782 one->config.ier_clear |= bit; 783 kthread_queue_work(&s->kworker, &one->reg_work); 784 } 785 786 static void sc16is7xx_stop_tx(struct uart_port *port) 787 { 788 sc16is7xx_ier_clear(port, SC16IS7XX_IER_THRI_BIT); 789 } 790 791 static void sc16is7xx_stop_rx(struct uart_port *port) 792 { 793 sc16is7xx_ier_clear(port, SC16IS7XX_IER_RDI_BIT); 794 } 795 796 static void sc16is7xx_start_tx(struct uart_port *port) 797 { 798 struct sc16is7xx_port *s = dev_get_drvdata(port->dev); 799 struct sc16is7xx_one *one = to_sc16is7xx_one(port, port); 800 801 kthread_queue_work(&s->kworker, &one->tx_work); 802 } 803 804 static unsigned int sc16is7xx_tx_empty(struct uart_port *port) 805 { 806 unsigned int lsr; 807 808 lsr = sc16is7xx_port_read(port, SC16IS7XX_LSR_REG); 809 810 return (lsr & SC16IS7XX_LSR_TEMT_BIT) ? TIOCSER_TEMT : 0; 811 } 812 813 static unsigned int sc16is7xx_get_mctrl(struct uart_port *port) 814 { 815 /* DCD and DSR are not wired and CTS/RTS is handled automatically 816 * so just indicate DSR and CAR asserted 817 */ 818 return TIOCM_DSR | TIOCM_CAR; 819 } 820 821 static void sc16is7xx_set_mctrl(struct uart_port *port, unsigned int mctrl) 822 { 823 struct sc16is7xx_port *s = dev_get_drvdata(port->dev); 824 struct sc16is7xx_one *one = to_sc16is7xx_one(port, port); 825 826 one->config.flags |= SC16IS7XX_RECONF_MD; 827 kthread_queue_work(&s->kworker, &one->reg_work); 828 } 829 830 static void sc16is7xx_break_ctl(struct uart_port *port, int break_state) 831 { 832 sc16is7xx_port_update(port, SC16IS7XX_LCR_REG, 833 SC16IS7XX_LCR_TXBREAK_BIT, 834 break_state ? SC16IS7XX_LCR_TXBREAK_BIT : 0); 835 } 836 837 static void sc16is7xx_set_termios(struct uart_port *port, 838 struct ktermios *termios, 839 struct ktermios *old) 840 { 841 struct sc16is7xx_port *s = dev_get_drvdata(port->dev); 842 unsigned int lcr, flow = 0; 843 int baud; 844 845 /* Mask termios capabilities we don't support */ 846 termios->c_cflag &= ~CMSPAR; 847 848 /* Word size */ 849 switch (termios->c_cflag & CSIZE) { 850 case CS5: 851 lcr = SC16IS7XX_LCR_WORD_LEN_5; 852 break; 853 case CS6: 854 lcr = SC16IS7XX_LCR_WORD_LEN_6; 855 break; 856 case CS7: 857 lcr = SC16IS7XX_LCR_WORD_LEN_7; 858 break; 859 case CS8: 860 lcr = SC16IS7XX_LCR_WORD_LEN_8; 861 break; 862 default: 863 lcr = SC16IS7XX_LCR_WORD_LEN_8; 864 termios->c_cflag &= ~CSIZE; 865 termios->c_cflag |= CS8; 866 break; 867 } 868 869 /* Parity */ 870 if (termios->c_cflag & PARENB) { 871 lcr |= SC16IS7XX_LCR_PARITY_BIT; 872 if (!(termios->c_cflag & PARODD)) 873 lcr |= SC16IS7XX_LCR_EVENPARITY_BIT; 874 } 875 876 /* Stop bits */ 877 if (termios->c_cflag & CSTOPB) 878 lcr |= SC16IS7XX_LCR_STOPLEN_BIT; /* 2 stops */ 879 880 /* Set read status mask */ 881 port->read_status_mask = SC16IS7XX_LSR_OE_BIT; 882 if (termios->c_iflag & INPCK) 883 port->read_status_mask |= SC16IS7XX_LSR_PE_BIT | 884 SC16IS7XX_LSR_FE_BIT; 885 if (termios->c_iflag & (BRKINT | PARMRK)) 886 port->read_status_mask |= SC16IS7XX_LSR_BI_BIT; 887 888 /* Set status ignore mask */ 889 port->ignore_status_mask = 0; 890 if (termios->c_iflag & IGNBRK) 891 port->ignore_status_mask |= SC16IS7XX_LSR_BI_BIT; 892 if (!(termios->c_cflag & CREAD)) 893 port->ignore_status_mask |= SC16IS7XX_LSR_BRK_ERROR_MASK; 894 895 sc16is7xx_port_write(port, SC16IS7XX_LCR_REG, 896 SC16IS7XX_LCR_CONF_MODE_B); 897 898 /* Configure flow control */ 899 regcache_cache_bypass(s->regmap, true); 900 sc16is7xx_port_write(port, SC16IS7XX_XON1_REG, termios->c_cc[VSTART]); 901 sc16is7xx_port_write(port, SC16IS7XX_XOFF1_REG, termios->c_cc[VSTOP]); 902 if (termios->c_cflag & CRTSCTS) 903 flow |= SC16IS7XX_EFR_AUTOCTS_BIT | 904 SC16IS7XX_EFR_AUTORTS_BIT; 905 if (termios->c_iflag & IXON) 906 flow |= SC16IS7XX_EFR_SWFLOW3_BIT; 907 if (termios->c_iflag & IXOFF) 908 flow |= SC16IS7XX_EFR_SWFLOW1_BIT; 909 910 sc16is7xx_port_write(port, SC16IS7XX_EFR_REG, flow); 911 regcache_cache_bypass(s->regmap, false); 912 913 /* Update LCR register */ 914 sc16is7xx_port_write(port, SC16IS7XX_LCR_REG, lcr); 915 916 /* Get baud rate generator configuration */ 917 baud = uart_get_baud_rate(port, termios, old, 918 port->uartclk / 16 / 4 / 0xffff, 919 port->uartclk / 16); 920 921 /* Setup baudrate generator */ 922 baud = sc16is7xx_set_baud(port, baud); 923 924 /* Update timeout according to new baud rate */ 925 uart_update_timeout(port, termios->c_cflag, baud); 926 } 927 928 static int sc16is7xx_config_rs485(struct uart_port *port, 929 struct serial_rs485 *rs485) 930 { 931 struct sc16is7xx_port *s = dev_get_drvdata(port->dev); 932 struct sc16is7xx_one *one = to_sc16is7xx_one(port, port); 933 934 if (rs485->flags & SER_RS485_ENABLED) { 935 bool rts_during_rx, rts_during_tx; 936 937 rts_during_rx = rs485->flags & SER_RS485_RTS_AFTER_SEND; 938 rts_during_tx = rs485->flags & SER_RS485_RTS_ON_SEND; 939 940 if (rts_during_rx == rts_during_tx) 941 dev_err(port->dev, 942 "unsupported RTS signalling on_send:%d after_send:%d - exactly one of RS485 RTS flags should be set\n", 943 rts_during_tx, rts_during_rx); 944 945 /* 946 * RTS signal is handled by HW, it's timing can't be influenced. 947 * However, it's sometimes useful to delay TX even without RTS 948 * control therefore we try to handle .delay_rts_before_send. 949 */ 950 if (rs485->delay_rts_after_send) 951 return -EINVAL; 952 } 953 954 port->rs485 = *rs485; 955 one->config.flags |= SC16IS7XX_RECONF_RS485; 956 kthread_queue_work(&s->kworker, &one->reg_work); 957 958 return 0; 959 } 960 961 static int sc16is7xx_startup(struct uart_port *port) 962 { 963 struct sc16is7xx_port *s = dev_get_drvdata(port->dev); 964 unsigned int val; 965 966 sc16is7xx_power(port, 1); 967 968 /* Reset FIFOs*/ 969 val = SC16IS7XX_FCR_RXRESET_BIT | SC16IS7XX_FCR_TXRESET_BIT; 970 sc16is7xx_port_write(port, SC16IS7XX_FCR_REG, val); 971 udelay(5); 972 sc16is7xx_port_write(port, SC16IS7XX_FCR_REG, 973 SC16IS7XX_FCR_FIFO_BIT); 974 975 /* Enable EFR */ 976 sc16is7xx_port_write(port, SC16IS7XX_LCR_REG, 977 SC16IS7XX_LCR_CONF_MODE_B); 978 979 regcache_cache_bypass(s->regmap, true); 980 981 /* Enable write access to enhanced features and internal clock div */ 982 sc16is7xx_port_write(port, SC16IS7XX_EFR_REG, 983 SC16IS7XX_EFR_ENABLE_BIT); 984 985 /* Enable TCR/TLR */ 986 sc16is7xx_port_update(port, SC16IS7XX_MCR_REG, 987 SC16IS7XX_MCR_TCRTLR_BIT, 988 SC16IS7XX_MCR_TCRTLR_BIT); 989 990 /* Configure flow control levels */ 991 /* Flow control halt level 48, resume level 24 */ 992 sc16is7xx_port_write(port, SC16IS7XX_TCR_REG, 993 SC16IS7XX_TCR_RX_RESUME(24) | 994 SC16IS7XX_TCR_RX_HALT(48)); 995 996 regcache_cache_bypass(s->regmap, false); 997 998 /* Now, initialize the UART */ 999 sc16is7xx_port_write(port, SC16IS7XX_LCR_REG, SC16IS7XX_LCR_WORD_LEN_8); 1000 1001 /* Enable the Rx and Tx FIFO */ 1002 sc16is7xx_port_update(port, SC16IS7XX_EFCR_REG, 1003 SC16IS7XX_EFCR_RXDISABLE_BIT | 1004 SC16IS7XX_EFCR_TXDISABLE_BIT, 1005 0); 1006 1007 /* Enable RX, TX interrupts */ 1008 val = SC16IS7XX_IER_RDI_BIT | SC16IS7XX_IER_THRI_BIT; 1009 sc16is7xx_port_write(port, SC16IS7XX_IER_REG, val); 1010 1011 return 0; 1012 } 1013 1014 static void sc16is7xx_shutdown(struct uart_port *port) 1015 { 1016 struct sc16is7xx_port *s = dev_get_drvdata(port->dev); 1017 1018 /* Disable all interrupts */ 1019 sc16is7xx_port_write(port, SC16IS7XX_IER_REG, 0); 1020 /* Disable TX/RX */ 1021 sc16is7xx_port_update(port, SC16IS7XX_EFCR_REG, 1022 SC16IS7XX_EFCR_RXDISABLE_BIT | 1023 SC16IS7XX_EFCR_TXDISABLE_BIT, 1024 SC16IS7XX_EFCR_RXDISABLE_BIT | 1025 SC16IS7XX_EFCR_TXDISABLE_BIT); 1026 1027 sc16is7xx_power(port, 0); 1028 1029 kthread_flush_worker(&s->kworker); 1030 } 1031 1032 static const char *sc16is7xx_type(struct uart_port *port) 1033 { 1034 struct sc16is7xx_port *s = dev_get_drvdata(port->dev); 1035 1036 return (port->type == PORT_SC16IS7XX) ? s->devtype->name : NULL; 1037 } 1038 1039 static int sc16is7xx_request_port(struct uart_port *port) 1040 { 1041 /* Do nothing */ 1042 return 0; 1043 } 1044 1045 static void sc16is7xx_config_port(struct uart_port *port, int flags) 1046 { 1047 if (flags & UART_CONFIG_TYPE) 1048 port->type = PORT_SC16IS7XX; 1049 } 1050 1051 static int sc16is7xx_verify_port(struct uart_port *port, 1052 struct serial_struct *s) 1053 { 1054 if ((s->type != PORT_UNKNOWN) && (s->type != PORT_SC16IS7XX)) 1055 return -EINVAL; 1056 if (s->irq != port->irq) 1057 return -EINVAL; 1058 1059 return 0; 1060 } 1061 1062 static void sc16is7xx_pm(struct uart_port *port, unsigned int state, 1063 unsigned int oldstate) 1064 { 1065 sc16is7xx_power(port, (state == UART_PM_STATE_ON) ? 1 : 0); 1066 } 1067 1068 static void sc16is7xx_null_void(struct uart_port *port) 1069 { 1070 /* Do nothing */ 1071 } 1072 1073 static const struct uart_ops sc16is7xx_ops = { 1074 .tx_empty = sc16is7xx_tx_empty, 1075 .set_mctrl = sc16is7xx_set_mctrl, 1076 .get_mctrl = sc16is7xx_get_mctrl, 1077 .stop_tx = sc16is7xx_stop_tx, 1078 .start_tx = sc16is7xx_start_tx, 1079 .stop_rx = sc16is7xx_stop_rx, 1080 .break_ctl = sc16is7xx_break_ctl, 1081 .startup = sc16is7xx_startup, 1082 .shutdown = sc16is7xx_shutdown, 1083 .set_termios = sc16is7xx_set_termios, 1084 .type = sc16is7xx_type, 1085 .request_port = sc16is7xx_request_port, 1086 .release_port = sc16is7xx_null_void, 1087 .config_port = sc16is7xx_config_port, 1088 .verify_port = sc16is7xx_verify_port, 1089 .pm = sc16is7xx_pm, 1090 }; 1091 1092 #ifdef CONFIG_GPIOLIB 1093 static int sc16is7xx_gpio_get(struct gpio_chip *chip, unsigned offset) 1094 { 1095 unsigned int val; 1096 struct sc16is7xx_port *s = gpiochip_get_data(chip); 1097 struct uart_port *port = &s->p[0].port; 1098 1099 val = sc16is7xx_port_read(port, SC16IS7XX_IOSTATE_REG); 1100 1101 return !!(val & BIT(offset)); 1102 } 1103 1104 static void sc16is7xx_gpio_set(struct gpio_chip *chip, unsigned offset, int val) 1105 { 1106 struct sc16is7xx_port *s = gpiochip_get_data(chip); 1107 struct uart_port *port = &s->p[0].port; 1108 1109 sc16is7xx_port_update(port, SC16IS7XX_IOSTATE_REG, BIT(offset), 1110 val ? BIT(offset) : 0); 1111 } 1112 1113 static int sc16is7xx_gpio_direction_input(struct gpio_chip *chip, 1114 unsigned offset) 1115 { 1116 struct sc16is7xx_port *s = gpiochip_get_data(chip); 1117 struct uart_port *port = &s->p[0].port; 1118 1119 sc16is7xx_port_update(port, SC16IS7XX_IODIR_REG, BIT(offset), 0); 1120 1121 return 0; 1122 } 1123 1124 static int sc16is7xx_gpio_direction_output(struct gpio_chip *chip, 1125 unsigned offset, int val) 1126 { 1127 struct sc16is7xx_port *s = gpiochip_get_data(chip); 1128 struct uart_port *port = &s->p[0].port; 1129 u8 state = sc16is7xx_port_read(port, SC16IS7XX_IOSTATE_REG); 1130 1131 if (val) 1132 state |= BIT(offset); 1133 else 1134 state &= ~BIT(offset); 1135 sc16is7xx_port_write(port, SC16IS7XX_IOSTATE_REG, state); 1136 sc16is7xx_port_update(port, SC16IS7XX_IODIR_REG, BIT(offset), 1137 BIT(offset)); 1138 1139 return 0; 1140 } 1141 #endif 1142 1143 static int sc16is7xx_probe(struct device *dev, 1144 const struct sc16is7xx_devtype *devtype, 1145 struct regmap *regmap, int irq, unsigned long flags) 1146 { 1147 struct sched_param sched_param = { .sched_priority = MAX_RT_PRIO / 2 }; 1148 unsigned long freq, *pfreq = dev_get_platdata(dev); 1149 int i, ret; 1150 struct sc16is7xx_port *s; 1151 1152 if (IS_ERR(regmap)) 1153 return PTR_ERR(regmap); 1154 1155 /* Alloc port structure */ 1156 s = devm_kzalloc(dev, sizeof(*s) + 1157 sizeof(struct sc16is7xx_one) * devtype->nr_uart, 1158 GFP_KERNEL); 1159 if (!s) { 1160 dev_err(dev, "Error allocating port structure\n"); 1161 return -ENOMEM; 1162 } 1163 1164 s->clk = devm_clk_get(dev, NULL); 1165 if (IS_ERR(s->clk)) { 1166 if (pfreq) 1167 freq = *pfreq; 1168 else 1169 return PTR_ERR(s->clk); 1170 } else { 1171 ret = clk_prepare_enable(s->clk); 1172 if (ret) 1173 return ret; 1174 1175 freq = clk_get_rate(s->clk); 1176 } 1177 1178 s->regmap = regmap; 1179 s->devtype = devtype; 1180 dev_set_drvdata(dev, s); 1181 1182 kthread_init_worker(&s->kworker); 1183 kthread_init_work(&s->irq_work, sc16is7xx_ist); 1184 s->kworker_task = kthread_run(kthread_worker_fn, &s->kworker, 1185 "sc16is7xx"); 1186 if (IS_ERR(s->kworker_task)) { 1187 ret = PTR_ERR(s->kworker_task); 1188 goto out_clk; 1189 } 1190 sched_setscheduler(s->kworker_task, SCHED_FIFO, &sched_param); 1191 1192 #ifdef CONFIG_GPIOLIB 1193 if (devtype->nr_gpio) { 1194 /* Setup GPIO cotroller */ 1195 s->gpio.owner = THIS_MODULE; 1196 s->gpio.parent = dev; 1197 s->gpio.label = dev_name(dev); 1198 s->gpio.direction_input = sc16is7xx_gpio_direction_input; 1199 s->gpio.get = sc16is7xx_gpio_get; 1200 s->gpio.direction_output = sc16is7xx_gpio_direction_output; 1201 s->gpio.set = sc16is7xx_gpio_set; 1202 s->gpio.base = -1; 1203 s->gpio.ngpio = devtype->nr_gpio; 1204 s->gpio.can_sleep = 1; 1205 ret = gpiochip_add_data(&s->gpio, s); 1206 if (ret) 1207 goto out_thread; 1208 } 1209 #endif 1210 1211 /* reset device, purging any pending irq / data */ 1212 regmap_write(s->regmap, SC16IS7XX_IOCONTROL_REG << SC16IS7XX_REG_SHIFT, 1213 SC16IS7XX_IOCONTROL_SRESET_BIT); 1214 1215 for (i = 0; i < devtype->nr_uart; ++i) { 1216 s->p[i].line = i; 1217 /* Initialize port data */ 1218 s->p[i].port.dev = dev; 1219 s->p[i].port.irq = irq; 1220 s->p[i].port.type = PORT_SC16IS7XX; 1221 s->p[i].port.fifosize = SC16IS7XX_FIFO_SIZE; 1222 s->p[i].port.flags = UPF_FIXED_TYPE | UPF_LOW_LATENCY; 1223 s->p[i].port.iotype = UPIO_PORT; 1224 s->p[i].port.uartclk = freq; 1225 s->p[i].port.rs485_config = sc16is7xx_config_rs485; 1226 s->p[i].port.ops = &sc16is7xx_ops; 1227 s->p[i].port.line = sc16is7xx_alloc_line(); 1228 if (s->p[i].port.line >= SC16IS7XX_MAX_DEVS) { 1229 ret = -ENOMEM; 1230 goto out_ports; 1231 } 1232 1233 /* Disable all interrupts */ 1234 sc16is7xx_port_write(&s->p[i].port, SC16IS7XX_IER_REG, 0); 1235 /* Disable TX/RX */ 1236 sc16is7xx_port_write(&s->p[i].port, SC16IS7XX_EFCR_REG, 1237 SC16IS7XX_EFCR_RXDISABLE_BIT | 1238 SC16IS7XX_EFCR_TXDISABLE_BIT); 1239 /* Initialize kthread work structs */ 1240 kthread_init_work(&s->p[i].tx_work, sc16is7xx_tx_proc); 1241 kthread_init_work(&s->p[i].reg_work, sc16is7xx_reg_proc); 1242 /* Register port */ 1243 uart_add_one_port(&sc16is7xx_uart, &s->p[i].port); 1244 1245 /* Enable EFR */ 1246 sc16is7xx_port_write(&s->p[i].port, SC16IS7XX_LCR_REG, 1247 SC16IS7XX_LCR_CONF_MODE_B); 1248 1249 regcache_cache_bypass(s->regmap, true); 1250 1251 /* Enable write access to enhanced features */ 1252 sc16is7xx_port_write(&s->p[i].port, SC16IS7XX_EFR_REG, 1253 SC16IS7XX_EFR_ENABLE_BIT); 1254 1255 regcache_cache_bypass(s->regmap, false); 1256 1257 /* Restore access to general registers */ 1258 sc16is7xx_port_write(&s->p[i].port, SC16IS7XX_LCR_REG, 0x00); 1259 1260 /* Go to suspend mode */ 1261 sc16is7xx_power(&s->p[i].port, 0); 1262 } 1263 1264 /* Setup interrupt */ 1265 ret = devm_request_irq(dev, irq, sc16is7xx_irq, 1266 flags, dev_name(dev), s); 1267 if (!ret) 1268 return 0; 1269 1270 out_ports: 1271 for (i--; i >= 0; i--) { 1272 uart_remove_one_port(&sc16is7xx_uart, &s->p[i].port); 1273 clear_bit(s->p[i].port.line, &sc16is7xx_lines); 1274 } 1275 1276 #ifdef CONFIG_GPIOLIB 1277 if (devtype->nr_gpio) 1278 gpiochip_remove(&s->gpio); 1279 1280 out_thread: 1281 #endif 1282 kthread_stop(s->kworker_task); 1283 1284 out_clk: 1285 if (!IS_ERR(s->clk)) 1286 clk_disable_unprepare(s->clk); 1287 1288 return ret; 1289 } 1290 1291 static int sc16is7xx_remove(struct device *dev) 1292 { 1293 struct sc16is7xx_port *s = dev_get_drvdata(dev); 1294 int i; 1295 1296 #ifdef CONFIG_GPIOLIB 1297 if (s->devtype->nr_gpio) 1298 gpiochip_remove(&s->gpio); 1299 #endif 1300 1301 for (i = 0; i < s->devtype->nr_uart; i++) { 1302 uart_remove_one_port(&sc16is7xx_uart, &s->p[i].port); 1303 clear_bit(s->p[i].port.line, &sc16is7xx_lines); 1304 sc16is7xx_power(&s->p[i].port, 0); 1305 } 1306 1307 kthread_flush_worker(&s->kworker); 1308 kthread_stop(s->kworker_task); 1309 1310 if (!IS_ERR(s->clk)) 1311 clk_disable_unprepare(s->clk); 1312 1313 return 0; 1314 } 1315 1316 static const struct of_device_id __maybe_unused sc16is7xx_dt_ids[] = { 1317 { .compatible = "nxp,sc16is740", .data = &sc16is74x_devtype, }, 1318 { .compatible = "nxp,sc16is741", .data = &sc16is74x_devtype, }, 1319 { .compatible = "nxp,sc16is750", .data = &sc16is750_devtype, }, 1320 { .compatible = "nxp,sc16is752", .data = &sc16is752_devtype, }, 1321 { .compatible = "nxp,sc16is760", .data = &sc16is760_devtype, }, 1322 { .compatible = "nxp,sc16is762", .data = &sc16is762_devtype, }, 1323 { } 1324 }; 1325 MODULE_DEVICE_TABLE(of, sc16is7xx_dt_ids); 1326 1327 static struct regmap_config regcfg = { 1328 .reg_bits = 7, 1329 .pad_bits = 1, 1330 .val_bits = 8, 1331 .cache_type = REGCACHE_RBTREE, 1332 .volatile_reg = sc16is7xx_regmap_volatile, 1333 .precious_reg = sc16is7xx_regmap_precious, 1334 }; 1335 1336 #ifdef CONFIG_SERIAL_SC16IS7XX_SPI 1337 static int sc16is7xx_spi_probe(struct spi_device *spi) 1338 { 1339 const struct sc16is7xx_devtype *devtype; 1340 unsigned long flags = 0; 1341 struct regmap *regmap; 1342 int ret; 1343 1344 /* Setup SPI bus */ 1345 spi->bits_per_word = 8; 1346 /* only supports mode 0 on SC16IS762 */ 1347 spi->mode = spi->mode ? : SPI_MODE_0; 1348 spi->max_speed_hz = spi->max_speed_hz ? : 15000000; 1349 ret = spi_setup(spi); 1350 if (ret) 1351 return ret; 1352 1353 if (spi->dev.of_node) { 1354 const struct of_device_id *of_id = 1355 of_match_device(sc16is7xx_dt_ids, &spi->dev); 1356 1357 if (!of_id) 1358 return -ENODEV; 1359 1360 devtype = (struct sc16is7xx_devtype *)of_id->data; 1361 } else { 1362 const struct spi_device_id *id_entry = spi_get_device_id(spi); 1363 1364 devtype = (struct sc16is7xx_devtype *)id_entry->driver_data; 1365 flags = IRQF_TRIGGER_FALLING; 1366 } 1367 1368 regcfg.max_register = (0xf << SC16IS7XX_REG_SHIFT) | 1369 (devtype->nr_uart - 1); 1370 regmap = devm_regmap_init_spi(spi, ®cfg); 1371 1372 return sc16is7xx_probe(&spi->dev, devtype, regmap, spi->irq, flags); 1373 } 1374 1375 static int sc16is7xx_spi_remove(struct spi_device *spi) 1376 { 1377 return sc16is7xx_remove(&spi->dev); 1378 } 1379 1380 static const struct spi_device_id sc16is7xx_spi_id_table[] = { 1381 { "sc16is74x", (kernel_ulong_t)&sc16is74x_devtype, }, 1382 { "sc16is740", (kernel_ulong_t)&sc16is74x_devtype, }, 1383 { "sc16is741", (kernel_ulong_t)&sc16is74x_devtype, }, 1384 { "sc16is750", (kernel_ulong_t)&sc16is750_devtype, }, 1385 { "sc16is752", (kernel_ulong_t)&sc16is752_devtype, }, 1386 { "sc16is760", (kernel_ulong_t)&sc16is760_devtype, }, 1387 { "sc16is762", (kernel_ulong_t)&sc16is762_devtype, }, 1388 { } 1389 }; 1390 1391 MODULE_DEVICE_TABLE(spi, sc16is7xx_spi_id_table); 1392 1393 static struct spi_driver sc16is7xx_spi_uart_driver = { 1394 .driver = { 1395 .name = SC16IS7XX_NAME, 1396 .of_match_table = of_match_ptr(sc16is7xx_dt_ids), 1397 }, 1398 .probe = sc16is7xx_spi_probe, 1399 .remove = sc16is7xx_spi_remove, 1400 .id_table = sc16is7xx_spi_id_table, 1401 }; 1402 1403 MODULE_ALIAS("spi:sc16is7xx"); 1404 #endif 1405 1406 #ifdef CONFIG_SERIAL_SC16IS7XX_I2C 1407 static int sc16is7xx_i2c_probe(struct i2c_client *i2c, 1408 const struct i2c_device_id *id) 1409 { 1410 const struct sc16is7xx_devtype *devtype; 1411 unsigned long flags = 0; 1412 struct regmap *regmap; 1413 1414 if (i2c->dev.of_node) { 1415 const struct of_device_id *of_id = 1416 of_match_device(sc16is7xx_dt_ids, &i2c->dev); 1417 1418 if (!of_id) 1419 return -ENODEV; 1420 1421 devtype = (struct sc16is7xx_devtype *)of_id->data; 1422 } else { 1423 devtype = (struct sc16is7xx_devtype *)id->driver_data; 1424 flags = IRQF_TRIGGER_FALLING; 1425 } 1426 1427 regcfg.max_register = (0xf << SC16IS7XX_REG_SHIFT) | 1428 (devtype->nr_uart - 1); 1429 regmap = devm_regmap_init_i2c(i2c, ®cfg); 1430 1431 return sc16is7xx_probe(&i2c->dev, devtype, regmap, i2c->irq, flags); 1432 } 1433 1434 static int sc16is7xx_i2c_remove(struct i2c_client *client) 1435 { 1436 return sc16is7xx_remove(&client->dev); 1437 } 1438 1439 static const struct i2c_device_id sc16is7xx_i2c_id_table[] = { 1440 { "sc16is74x", (kernel_ulong_t)&sc16is74x_devtype, }, 1441 { "sc16is740", (kernel_ulong_t)&sc16is74x_devtype, }, 1442 { "sc16is741", (kernel_ulong_t)&sc16is74x_devtype, }, 1443 { "sc16is750", (kernel_ulong_t)&sc16is750_devtype, }, 1444 { "sc16is752", (kernel_ulong_t)&sc16is752_devtype, }, 1445 { "sc16is760", (kernel_ulong_t)&sc16is760_devtype, }, 1446 { "sc16is762", (kernel_ulong_t)&sc16is762_devtype, }, 1447 { } 1448 }; 1449 MODULE_DEVICE_TABLE(i2c, sc16is7xx_i2c_id_table); 1450 1451 static struct i2c_driver sc16is7xx_i2c_uart_driver = { 1452 .driver = { 1453 .name = SC16IS7XX_NAME, 1454 .of_match_table = of_match_ptr(sc16is7xx_dt_ids), 1455 }, 1456 .probe = sc16is7xx_i2c_probe, 1457 .remove = sc16is7xx_i2c_remove, 1458 .id_table = sc16is7xx_i2c_id_table, 1459 }; 1460 1461 #endif 1462 1463 static int __init sc16is7xx_init(void) 1464 { 1465 int ret; 1466 1467 ret = uart_register_driver(&sc16is7xx_uart); 1468 if (ret) { 1469 pr_err("Registering UART driver failed\n"); 1470 return ret; 1471 } 1472 1473 #ifdef CONFIG_SERIAL_SC16IS7XX_I2C 1474 ret = i2c_add_driver(&sc16is7xx_i2c_uart_driver); 1475 if (ret < 0) { 1476 pr_err("failed to init sc16is7xx i2c --> %d\n", ret); 1477 return ret; 1478 } 1479 #endif 1480 1481 #ifdef CONFIG_SERIAL_SC16IS7XX_SPI 1482 ret = spi_register_driver(&sc16is7xx_spi_uart_driver); 1483 if (ret < 0) { 1484 pr_err("failed to init sc16is7xx spi --> %d\n", ret); 1485 return ret; 1486 } 1487 #endif 1488 return ret; 1489 } 1490 module_init(sc16is7xx_init); 1491 1492 static void __exit sc16is7xx_exit(void) 1493 { 1494 #ifdef CONFIG_SERIAL_SC16IS7XX_I2C 1495 i2c_del_driver(&sc16is7xx_i2c_uart_driver); 1496 #endif 1497 1498 #ifdef CONFIG_SERIAL_SC16IS7XX_SPI 1499 spi_unregister_driver(&sc16is7xx_spi_uart_driver); 1500 #endif 1501 uart_unregister_driver(&sc16is7xx_uart); 1502 } 1503 module_exit(sc16is7xx_exit); 1504 1505 MODULE_LICENSE("GPL"); 1506 MODULE_AUTHOR("Jon Ringle <jringle@gridpoint.com>"); 1507 MODULE_DESCRIPTION("SC16IS7XX serial driver"); 1508