1 /* 2 * SC16IS7xx tty serial driver - Copyright (C) 2014 GridPoint 3 * Author: Jon Ringle <jringle@gridpoint.com> 4 * 5 * Based on max310x.c, by Alexander Shiyan <shc_work@mail.ru> 6 * 7 * This program is free software; you can redistribute it and/or modify 8 * it under the terms of the GNU General Public License as published by 9 * the Free Software Foundation; either version 2 of the License, or 10 * (at your option) any later version. 11 * 12 */ 13 14 #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt 15 16 #include <linux/bitops.h> 17 #include <linux/clk.h> 18 #include <linux/delay.h> 19 #include <linux/device.h> 20 #include <linux/gpio/driver.h> 21 #include <linux/i2c.h> 22 #include <linux/module.h> 23 #include <linux/of.h> 24 #include <linux/of_device.h> 25 #include <linux/regmap.h> 26 #include <linux/serial_core.h> 27 #include <linux/serial.h> 28 #include <linux/tty.h> 29 #include <linux/tty_flip.h> 30 #include <linux/spi/spi.h> 31 #include <linux/uaccess.h> 32 33 #define SC16IS7XX_NAME "sc16is7xx" 34 #define SC16IS7XX_MAX_DEVS 8 35 36 /* SC16IS7XX register definitions */ 37 #define SC16IS7XX_RHR_REG (0x00) /* RX FIFO */ 38 #define SC16IS7XX_THR_REG (0x00) /* TX FIFO */ 39 #define SC16IS7XX_IER_REG (0x01) /* Interrupt enable */ 40 #define SC16IS7XX_IIR_REG (0x02) /* Interrupt Identification */ 41 #define SC16IS7XX_FCR_REG (0x02) /* FIFO control */ 42 #define SC16IS7XX_LCR_REG (0x03) /* Line Control */ 43 #define SC16IS7XX_MCR_REG (0x04) /* Modem Control */ 44 #define SC16IS7XX_LSR_REG (0x05) /* Line Status */ 45 #define SC16IS7XX_MSR_REG (0x06) /* Modem Status */ 46 #define SC16IS7XX_SPR_REG (0x07) /* Scratch Pad */ 47 #define SC16IS7XX_TXLVL_REG (0x08) /* TX FIFO level */ 48 #define SC16IS7XX_RXLVL_REG (0x09) /* RX FIFO level */ 49 #define SC16IS7XX_IODIR_REG (0x0a) /* I/O Direction 50 * - only on 75x/76x 51 */ 52 #define SC16IS7XX_IOSTATE_REG (0x0b) /* I/O State 53 * - only on 75x/76x 54 */ 55 #define SC16IS7XX_IOINTENA_REG (0x0c) /* I/O Interrupt Enable 56 * - only on 75x/76x 57 */ 58 #define SC16IS7XX_IOCONTROL_REG (0x0e) /* I/O Control 59 * - only on 75x/76x 60 */ 61 #define SC16IS7XX_EFCR_REG (0x0f) /* Extra Features Control */ 62 63 /* TCR/TLR Register set: Only if ((MCR[2] == 1) && (EFR[4] == 1)) */ 64 #define SC16IS7XX_TCR_REG (0x06) /* Transmit control */ 65 #define SC16IS7XX_TLR_REG (0x07) /* Trigger level */ 66 67 /* Special Register set: Only if ((LCR[7] == 1) && (LCR != 0xBF)) */ 68 #define SC16IS7XX_DLL_REG (0x00) /* Divisor Latch Low */ 69 #define SC16IS7XX_DLH_REG (0x01) /* Divisor Latch High */ 70 71 /* Enhanced Register set: Only if (LCR == 0xBF) */ 72 #define SC16IS7XX_EFR_REG (0x02) /* Enhanced Features */ 73 #define SC16IS7XX_XON1_REG (0x04) /* Xon1 word */ 74 #define SC16IS7XX_XON2_REG (0x05) /* Xon2 word */ 75 #define SC16IS7XX_XOFF1_REG (0x06) /* Xoff1 word */ 76 #define SC16IS7XX_XOFF2_REG (0x07) /* Xoff2 word */ 77 78 /* IER register bits */ 79 #define SC16IS7XX_IER_RDI_BIT (1 << 0) /* Enable RX data interrupt */ 80 #define SC16IS7XX_IER_THRI_BIT (1 << 1) /* Enable TX holding register 81 * interrupt */ 82 #define SC16IS7XX_IER_RLSI_BIT (1 << 2) /* Enable RX line status 83 * interrupt */ 84 #define SC16IS7XX_IER_MSI_BIT (1 << 3) /* Enable Modem status 85 * interrupt */ 86 87 /* IER register bits - write only if (EFR[4] == 1) */ 88 #define SC16IS7XX_IER_SLEEP_BIT (1 << 4) /* Enable Sleep mode */ 89 #define SC16IS7XX_IER_XOFFI_BIT (1 << 5) /* Enable Xoff interrupt */ 90 #define SC16IS7XX_IER_RTSI_BIT (1 << 6) /* Enable nRTS interrupt */ 91 #define SC16IS7XX_IER_CTSI_BIT (1 << 7) /* Enable nCTS interrupt */ 92 93 /* FCR register bits */ 94 #define SC16IS7XX_FCR_FIFO_BIT (1 << 0) /* Enable FIFO */ 95 #define SC16IS7XX_FCR_RXRESET_BIT (1 << 1) /* Reset RX FIFO */ 96 #define SC16IS7XX_FCR_TXRESET_BIT (1 << 2) /* Reset TX FIFO */ 97 #define SC16IS7XX_FCR_RXLVLL_BIT (1 << 6) /* RX Trigger level LSB */ 98 #define SC16IS7XX_FCR_RXLVLH_BIT (1 << 7) /* RX Trigger level MSB */ 99 100 /* FCR register bits - write only if (EFR[4] == 1) */ 101 #define SC16IS7XX_FCR_TXLVLL_BIT (1 << 4) /* TX Trigger level LSB */ 102 #define SC16IS7XX_FCR_TXLVLH_BIT (1 << 5) /* TX Trigger level MSB */ 103 104 /* IIR register bits */ 105 #define SC16IS7XX_IIR_NO_INT_BIT (1 << 0) /* No interrupts pending */ 106 #define SC16IS7XX_IIR_ID_MASK 0x3e /* Mask for the interrupt ID */ 107 #define SC16IS7XX_IIR_THRI_SRC 0x02 /* TX holding register empty */ 108 #define SC16IS7XX_IIR_RDI_SRC 0x04 /* RX data interrupt */ 109 #define SC16IS7XX_IIR_RLSE_SRC 0x06 /* RX line status error */ 110 #define SC16IS7XX_IIR_RTOI_SRC 0x0c /* RX time-out interrupt */ 111 #define SC16IS7XX_IIR_MSI_SRC 0x00 /* Modem status interrupt 112 * - only on 75x/76x 113 */ 114 #define SC16IS7XX_IIR_INPIN_SRC 0x30 /* Input pin change of state 115 * - only on 75x/76x 116 */ 117 #define SC16IS7XX_IIR_XOFFI_SRC 0x10 /* Received Xoff */ 118 #define SC16IS7XX_IIR_CTSRTS_SRC 0x20 /* nCTS,nRTS change of state 119 * from active (LOW) 120 * to inactive (HIGH) 121 */ 122 /* LCR register bits */ 123 #define SC16IS7XX_LCR_LENGTH0_BIT (1 << 0) /* Word length bit 0 */ 124 #define SC16IS7XX_LCR_LENGTH1_BIT (1 << 1) /* Word length bit 1 125 * 126 * Word length bits table: 127 * 00 -> 5 bit words 128 * 01 -> 6 bit words 129 * 10 -> 7 bit words 130 * 11 -> 8 bit words 131 */ 132 #define SC16IS7XX_LCR_STOPLEN_BIT (1 << 2) /* STOP length bit 133 * 134 * STOP length bit table: 135 * 0 -> 1 stop bit 136 * 1 -> 1-1.5 stop bits if 137 * word length is 5, 138 * 2 stop bits otherwise 139 */ 140 #define SC16IS7XX_LCR_PARITY_BIT (1 << 3) /* Parity bit enable */ 141 #define SC16IS7XX_LCR_EVENPARITY_BIT (1 << 4) /* Even parity bit enable */ 142 #define SC16IS7XX_LCR_FORCEPARITY_BIT (1 << 5) /* 9-bit multidrop parity */ 143 #define SC16IS7XX_LCR_TXBREAK_BIT (1 << 6) /* TX break enable */ 144 #define SC16IS7XX_LCR_DLAB_BIT (1 << 7) /* Divisor Latch enable */ 145 #define SC16IS7XX_LCR_WORD_LEN_5 (0x00) 146 #define SC16IS7XX_LCR_WORD_LEN_6 (0x01) 147 #define SC16IS7XX_LCR_WORD_LEN_7 (0x02) 148 #define SC16IS7XX_LCR_WORD_LEN_8 (0x03) 149 #define SC16IS7XX_LCR_CONF_MODE_A SC16IS7XX_LCR_DLAB_BIT /* Special 150 * reg set */ 151 #define SC16IS7XX_LCR_CONF_MODE_B 0xBF /* Enhanced 152 * reg set */ 153 154 /* MCR register bits */ 155 #define SC16IS7XX_MCR_DTR_BIT (1 << 0) /* DTR complement 156 * - only on 75x/76x 157 */ 158 #define SC16IS7XX_MCR_RTS_BIT (1 << 1) /* RTS complement */ 159 #define SC16IS7XX_MCR_TCRTLR_BIT (1 << 2) /* TCR/TLR register enable */ 160 #define SC16IS7XX_MCR_LOOP_BIT (1 << 4) /* Enable loopback test mode */ 161 #define SC16IS7XX_MCR_XONANY_BIT (1 << 5) /* Enable Xon Any 162 * - write enabled 163 * if (EFR[4] == 1) 164 */ 165 #define SC16IS7XX_MCR_IRDA_BIT (1 << 6) /* Enable IrDA mode 166 * - write enabled 167 * if (EFR[4] == 1) 168 */ 169 #define SC16IS7XX_MCR_CLKSEL_BIT (1 << 7) /* Divide clock by 4 170 * - write enabled 171 * if (EFR[4] == 1) 172 */ 173 174 /* LSR register bits */ 175 #define SC16IS7XX_LSR_DR_BIT (1 << 0) /* Receiver data ready */ 176 #define SC16IS7XX_LSR_OE_BIT (1 << 1) /* Overrun Error */ 177 #define SC16IS7XX_LSR_PE_BIT (1 << 2) /* Parity Error */ 178 #define SC16IS7XX_LSR_FE_BIT (1 << 3) /* Frame Error */ 179 #define SC16IS7XX_LSR_BI_BIT (1 << 4) /* Break Interrupt */ 180 #define SC16IS7XX_LSR_BRK_ERROR_MASK 0x1E /* BI, FE, PE, OE bits */ 181 #define SC16IS7XX_LSR_THRE_BIT (1 << 5) /* TX holding register empty */ 182 #define SC16IS7XX_LSR_TEMT_BIT (1 << 6) /* Transmitter empty */ 183 #define SC16IS7XX_LSR_FIFOE_BIT (1 << 7) /* Fifo Error */ 184 185 /* MSR register bits */ 186 #define SC16IS7XX_MSR_DCTS_BIT (1 << 0) /* Delta CTS Clear To Send */ 187 #define SC16IS7XX_MSR_DDSR_BIT (1 << 1) /* Delta DSR Data Set Ready 188 * or (IO4) 189 * - only on 75x/76x 190 */ 191 #define SC16IS7XX_MSR_DRI_BIT (1 << 2) /* Delta RI Ring Indicator 192 * or (IO7) 193 * - only on 75x/76x 194 */ 195 #define SC16IS7XX_MSR_DCD_BIT (1 << 3) /* Delta CD Carrier Detect 196 * or (IO6) 197 * - only on 75x/76x 198 */ 199 #define SC16IS7XX_MSR_CTS_BIT (1 << 4) /* CTS */ 200 #define SC16IS7XX_MSR_DSR_BIT (1 << 5) /* DSR (IO4) 201 * - only on 75x/76x 202 */ 203 #define SC16IS7XX_MSR_RI_BIT (1 << 6) /* RI (IO7) 204 * - only on 75x/76x 205 */ 206 #define SC16IS7XX_MSR_CD_BIT (1 << 7) /* CD (IO6) 207 * - only on 75x/76x 208 */ 209 #define SC16IS7XX_MSR_DELTA_MASK 0x0F /* Any of the delta bits! */ 210 211 /* 212 * TCR register bits 213 * TCR trigger levels are available from 0 to 60 characters with a granularity 214 * of four. 215 * The programmer must program the TCR such that TCR[3:0] > TCR[7:4]. There is 216 * no built-in hardware check to make sure this condition is met. Also, the TCR 217 * must be programmed with this condition before auto RTS or software flow 218 * control is enabled to avoid spurious operation of the device. 219 */ 220 #define SC16IS7XX_TCR_RX_HALT(words) ((((words) / 4) & 0x0f) << 0) 221 #define SC16IS7XX_TCR_RX_RESUME(words) ((((words) / 4) & 0x0f) << 4) 222 223 /* 224 * TLR register bits 225 * If TLR[3:0] or TLR[7:4] are logical 0, the selectable trigger levels via the 226 * FIFO Control Register (FCR) are used for the transmit and receive FIFO 227 * trigger levels. Trigger levels from 4 characters to 60 characters are 228 * available with a granularity of four. 229 * 230 * When the trigger level setting in TLR is zero, the SC16IS740/750/760 uses the 231 * trigger level setting defined in FCR. If TLR has non-zero trigger level value 232 * the trigger level defined in FCR is discarded. This applies to both transmit 233 * FIFO and receive FIFO trigger level setting. 234 * 235 * When TLR is used for RX trigger level control, FCR[7:6] should be left at the 236 * default state, that is, '00'. 237 */ 238 #define SC16IS7XX_TLR_TX_TRIGGER(words) ((((words) / 4) & 0x0f) << 0) 239 #define SC16IS7XX_TLR_RX_TRIGGER(words) ((((words) / 4) & 0x0f) << 4) 240 241 /* IOControl register bits (Only 750/760) */ 242 #define SC16IS7XX_IOCONTROL_LATCH_BIT (1 << 0) /* Enable input latching */ 243 #define SC16IS7XX_IOCONTROL_MODEM_BIT (1 << 1) /* Enable GPIO[7:4] as modem pins */ 244 #define SC16IS7XX_IOCONTROL_SRESET_BIT (1 << 3) /* Software Reset */ 245 246 /* EFCR register bits */ 247 #define SC16IS7XX_EFCR_9BIT_MODE_BIT (1 << 0) /* Enable 9-bit or Multidrop 248 * mode (RS485) */ 249 #define SC16IS7XX_EFCR_RXDISABLE_BIT (1 << 1) /* Disable receiver */ 250 #define SC16IS7XX_EFCR_TXDISABLE_BIT (1 << 2) /* Disable transmitter */ 251 #define SC16IS7XX_EFCR_AUTO_RS485_BIT (1 << 4) /* Auto RS485 RTS direction */ 252 #define SC16IS7XX_EFCR_RTS_INVERT_BIT (1 << 5) /* RTS output inversion */ 253 #define SC16IS7XX_EFCR_IRDA_MODE_BIT (1 << 7) /* IrDA mode 254 * 0 = rate upto 115.2 kbit/s 255 * - Only 750/760 256 * 1 = rate upto 1.152 Mbit/s 257 * - Only 760 258 */ 259 260 /* EFR register bits */ 261 #define SC16IS7XX_EFR_AUTORTS_BIT (1 << 6) /* Auto RTS flow ctrl enable */ 262 #define SC16IS7XX_EFR_AUTOCTS_BIT (1 << 7) /* Auto CTS flow ctrl enable */ 263 #define SC16IS7XX_EFR_XOFF2_DETECT_BIT (1 << 5) /* Enable Xoff2 detection */ 264 #define SC16IS7XX_EFR_ENABLE_BIT (1 << 4) /* Enable enhanced functions 265 * and writing to IER[7:4], 266 * FCR[5:4], MCR[7:5] 267 */ 268 #define SC16IS7XX_EFR_SWFLOW3_BIT (1 << 3) /* SWFLOW bit 3 */ 269 #define SC16IS7XX_EFR_SWFLOW2_BIT (1 << 2) /* SWFLOW bit 2 270 * 271 * SWFLOW bits 3 & 2 table: 272 * 00 -> no transmitter flow 273 * control 274 * 01 -> transmitter generates 275 * XON2 and XOFF2 276 * 10 -> transmitter generates 277 * XON1 and XOFF1 278 * 11 -> transmitter generates 279 * XON1, XON2, XOFF1 and 280 * XOFF2 281 */ 282 #define SC16IS7XX_EFR_SWFLOW1_BIT (1 << 1) /* SWFLOW bit 2 */ 283 #define SC16IS7XX_EFR_SWFLOW0_BIT (1 << 0) /* SWFLOW bit 3 284 * 285 * SWFLOW bits 3 & 2 table: 286 * 00 -> no received flow 287 * control 288 * 01 -> receiver compares 289 * XON2 and XOFF2 290 * 10 -> receiver compares 291 * XON1 and XOFF1 292 * 11 -> receiver compares 293 * XON1, XON2, XOFF1 and 294 * XOFF2 295 */ 296 297 /* Misc definitions */ 298 #define SC16IS7XX_FIFO_SIZE (64) 299 #define SC16IS7XX_REG_SHIFT 2 300 301 struct sc16is7xx_devtype { 302 char name[10]; 303 int nr_gpio; 304 int nr_uart; 305 }; 306 307 #define SC16IS7XX_RECONF_MD (1 << 0) 308 #define SC16IS7XX_RECONF_IER (1 << 1) 309 #define SC16IS7XX_RECONF_RS485 (1 << 2) 310 311 struct sc16is7xx_one_config { 312 unsigned int flags; 313 u8 ier_clear; 314 }; 315 316 struct sc16is7xx_one { 317 struct uart_port port; 318 u8 line; 319 struct kthread_work tx_work; 320 struct kthread_work reg_work; 321 struct sc16is7xx_one_config config; 322 }; 323 324 struct sc16is7xx_port { 325 const struct sc16is7xx_devtype *devtype; 326 struct regmap *regmap; 327 struct clk *clk; 328 #ifdef CONFIG_GPIOLIB 329 struct gpio_chip gpio; 330 #endif 331 unsigned char buf[SC16IS7XX_FIFO_SIZE]; 332 struct kthread_worker kworker; 333 struct task_struct *kworker_task; 334 struct kthread_work irq_work; 335 struct sc16is7xx_one p[0]; 336 }; 337 338 static unsigned long sc16is7xx_lines; 339 340 static struct uart_driver sc16is7xx_uart = { 341 .owner = THIS_MODULE, 342 .dev_name = "ttySC", 343 .nr = SC16IS7XX_MAX_DEVS, 344 }; 345 346 #define to_sc16is7xx_port(p,e) ((container_of((p), struct sc16is7xx_port, e))) 347 #define to_sc16is7xx_one(p,e) ((container_of((p), struct sc16is7xx_one, e))) 348 349 static int sc16is7xx_line(struct uart_port *port) 350 { 351 struct sc16is7xx_one *one = to_sc16is7xx_one(port, port); 352 353 return one->line; 354 } 355 356 static u8 sc16is7xx_port_read(struct uart_port *port, u8 reg) 357 { 358 struct sc16is7xx_port *s = dev_get_drvdata(port->dev); 359 unsigned int val = 0; 360 const u8 line = sc16is7xx_line(port); 361 362 regmap_read(s->regmap, (reg << SC16IS7XX_REG_SHIFT) | line, &val); 363 364 return val; 365 } 366 367 static void sc16is7xx_port_write(struct uart_port *port, u8 reg, u8 val) 368 { 369 struct sc16is7xx_port *s = dev_get_drvdata(port->dev); 370 const u8 line = sc16is7xx_line(port); 371 372 regmap_write(s->regmap, (reg << SC16IS7XX_REG_SHIFT) | line, val); 373 } 374 375 static void sc16is7xx_fifo_read(struct uart_port *port, unsigned int rxlen) 376 { 377 struct sc16is7xx_port *s = dev_get_drvdata(port->dev); 378 const u8 line = sc16is7xx_line(port); 379 u8 addr = (SC16IS7XX_RHR_REG << SC16IS7XX_REG_SHIFT) | line; 380 381 regcache_cache_bypass(s->regmap, true); 382 regmap_raw_read(s->regmap, addr, s->buf, rxlen); 383 regcache_cache_bypass(s->regmap, false); 384 } 385 386 static void sc16is7xx_fifo_write(struct uart_port *port, u8 to_send) 387 { 388 struct sc16is7xx_port *s = dev_get_drvdata(port->dev); 389 const u8 line = sc16is7xx_line(port); 390 u8 addr = (SC16IS7XX_THR_REG << SC16IS7XX_REG_SHIFT) | line; 391 392 /* 393 * Don't send zero-length data, at least on SPI it confuses the chip 394 * delivering wrong TXLVL data. 395 */ 396 if (unlikely(!to_send)) 397 return; 398 399 regcache_cache_bypass(s->regmap, true); 400 regmap_raw_write(s->regmap, addr, s->buf, to_send); 401 regcache_cache_bypass(s->regmap, false); 402 } 403 404 static void sc16is7xx_port_update(struct uart_port *port, u8 reg, 405 u8 mask, u8 val) 406 { 407 struct sc16is7xx_port *s = dev_get_drvdata(port->dev); 408 const u8 line = sc16is7xx_line(port); 409 410 regmap_update_bits(s->regmap, (reg << SC16IS7XX_REG_SHIFT) | line, 411 mask, val); 412 } 413 414 static int sc16is7xx_alloc_line(void) 415 { 416 int i; 417 418 BUILD_BUG_ON(SC16IS7XX_MAX_DEVS > BITS_PER_LONG); 419 420 for (i = 0; i < SC16IS7XX_MAX_DEVS; i++) 421 if (!test_and_set_bit(i, &sc16is7xx_lines)) 422 break; 423 424 return i; 425 } 426 427 static void sc16is7xx_power(struct uart_port *port, int on) 428 { 429 sc16is7xx_port_update(port, SC16IS7XX_IER_REG, 430 SC16IS7XX_IER_SLEEP_BIT, 431 on ? 0 : SC16IS7XX_IER_SLEEP_BIT); 432 } 433 434 static const struct sc16is7xx_devtype sc16is74x_devtype = { 435 .name = "SC16IS74X", 436 .nr_gpio = 0, 437 .nr_uart = 1, 438 }; 439 440 static const struct sc16is7xx_devtype sc16is750_devtype = { 441 .name = "SC16IS750", 442 .nr_gpio = 8, 443 .nr_uart = 1, 444 }; 445 446 static const struct sc16is7xx_devtype sc16is752_devtype = { 447 .name = "SC16IS752", 448 .nr_gpio = 8, 449 .nr_uart = 2, 450 }; 451 452 static const struct sc16is7xx_devtype sc16is760_devtype = { 453 .name = "SC16IS760", 454 .nr_gpio = 8, 455 .nr_uart = 1, 456 }; 457 458 static const struct sc16is7xx_devtype sc16is762_devtype = { 459 .name = "SC16IS762", 460 .nr_gpio = 8, 461 .nr_uart = 2, 462 }; 463 464 static bool sc16is7xx_regmap_volatile(struct device *dev, unsigned int reg) 465 { 466 switch (reg >> SC16IS7XX_REG_SHIFT) { 467 case SC16IS7XX_RHR_REG: 468 case SC16IS7XX_IIR_REG: 469 case SC16IS7XX_LSR_REG: 470 case SC16IS7XX_MSR_REG: 471 case SC16IS7XX_TXLVL_REG: 472 case SC16IS7XX_RXLVL_REG: 473 case SC16IS7XX_IOSTATE_REG: 474 return true; 475 default: 476 break; 477 } 478 479 return false; 480 } 481 482 static bool sc16is7xx_regmap_precious(struct device *dev, unsigned int reg) 483 { 484 switch (reg >> SC16IS7XX_REG_SHIFT) { 485 case SC16IS7XX_RHR_REG: 486 return true; 487 default: 488 break; 489 } 490 491 return false; 492 } 493 494 static int sc16is7xx_set_baud(struct uart_port *port, int baud) 495 { 496 struct sc16is7xx_port *s = dev_get_drvdata(port->dev); 497 u8 lcr; 498 u8 prescaler = 0; 499 unsigned long clk = port->uartclk, div = clk / 16 / baud; 500 501 if (div > 0xffff) { 502 prescaler = SC16IS7XX_MCR_CLKSEL_BIT; 503 div /= 4; 504 } 505 506 lcr = sc16is7xx_port_read(port, SC16IS7XX_LCR_REG); 507 508 /* Open the LCR divisors for configuration */ 509 sc16is7xx_port_write(port, SC16IS7XX_LCR_REG, 510 SC16IS7XX_LCR_CONF_MODE_B); 511 512 /* Enable enhanced features */ 513 regcache_cache_bypass(s->regmap, true); 514 sc16is7xx_port_write(port, SC16IS7XX_EFR_REG, 515 SC16IS7XX_EFR_ENABLE_BIT); 516 regcache_cache_bypass(s->regmap, false); 517 518 /* Put LCR back to the normal mode */ 519 sc16is7xx_port_write(port, SC16IS7XX_LCR_REG, lcr); 520 521 sc16is7xx_port_update(port, SC16IS7XX_MCR_REG, 522 SC16IS7XX_MCR_CLKSEL_BIT, 523 prescaler); 524 525 /* Open the LCR divisors for configuration */ 526 sc16is7xx_port_write(port, SC16IS7XX_LCR_REG, 527 SC16IS7XX_LCR_CONF_MODE_A); 528 529 /* Write the new divisor */ 530 regcache_cache_bypass(s->regmap, true); 531 sc16is7xx_port_write(port, SC16IS7XX_DLH_REG, div / 256); 532 sc16is7xx_port_write(port, SC16IS7XX_DLL_REG, div % 256); 533 regcache_cache_bypass(s->regmap, false); 534 535 /* Put LCR back to the normal mode */ 536 sc16is7xx_port_write(port, SC16IS7XX_LCR_REG, lcr); 537 538 return DIV_ROUND_CLOSEST(clk / 16, div); 539 } 540 541 static void sc16is7xx_handle_rx(struct uart_port *port, unsigned int rxlen, 542 unsigned int iir) 543 { 544 struct sc16is7xx_port *s = dev_get_drvdata(port->dev); 545 unsigned int lsr = 0, ch, flag, bytes_read, i; 546 bool read_lsr = (iir == SC16IS7XX_IIR_RLSE_SRC) ? true : false; 547 548 if (unlikely(rxlen >= sizeof(s->buf))) { 549 dev_warn_ratelimited(port->dev, 550 "ttySC%i: Possible RX FIFO overrun: %d\n", 551 port->line, rxlen); 552 port->icount.buf_overrun++; 553 /* Ensure sanity of RX level */ 554 rxlen = sizeof(s->buf); 555 } 556 557 while (rxlen) { 558 /* Only read lsr if there are possible errors in FIFO */ 559 if (read_lsr) { 560 lsr = sc16is7xx_port_read(port, SC16IS7XX_LSR_REG); 561 if (!(lsr & SC16IS7XX_LSR_FIFOE_BIT)) 562 read_lsr = false; /* No errors left in FIFO */ 563 } else 564 lsr = 0; 565 566 if (read_lsr) { 567 s->buf[0] = sc16is7xx_port_read(port, SC16IS7XX_RHR_REG); 568 bytes_read = 1; 569 } else { 570 sc16is7xx_fifo_read(port, rxlen); 571 bytes_read = rxlen; 572 } 573 574 lsr &= SC16IS7XX_LSR_BRK_ERROR_MASK; 575 576 port->icount.rx++; 577 flag = TTY_NORMAL; 578 579 if (unlikely(lsr)) { 580 if (lsr & SC16IS7XX_LSR_BI_BIT) { 581 port->icount.brk++; 582 if (uart_handle_break(port)) 583 continue; 584 } else if (lsr & SC16IS7XX_LSR_PE_BIT) 585 port->icount.parity++; 586 else if (lsr & SC16IS7XX_LSR_FE_BIT) 587 port->icount.frame++; 588 else if (lsr & SC16IS7XX_LSR_OE_BIT) 589 port->icount.overrun++; 590 591 lsr &= port->read_status_mask; 592 if (lsr & SC16IS7XX_LSR_BI_BIT) 593 flag = TTY_BREAK; 594 else if (lsr & SC16IS7XX_LSR_PE_BIT) 595 flag = TTY_PARITY; 596 else if (lsr & SC16IS7XX_LSR_FE_BIT) 597 flag = TTY_FRAME; 598 else if (lsr & SC16IS7XX_LSR_OE_BIT) 599 flag = TTY_OVERRUN; 600 } 601 602 for (i = 0; i < bytes_read; ++i) { 603 ch = s->buf[i]; 604 if (uart_handle_sysrq_char(port, ch)) 605 continue; 606 607 if (lsr & port->ignore_status_mask) 608 continue; 609 610 uart_insert_char(port, lsr, SC16IS7XX_LSR_OE_BIT, ch, 611 flag); 612 } 613 rxlen -= bytes_read; 614 } 615 616 tty_flip_buffer_push(&port->state->port); 617 } 618 619 static void sc16is7xx_handle_tx(struct uart_port *port) 620 { 621 struct sc16is7xx_port *s = dev_get_drvdata(port->dev); 622 struct circ_buf *xmit = &port->state->xmit; 623 unsigned int txlen, to_send, i; 624 625 if (unlikely(port->x_char)) { 626 sc16is7xx_port_write(port, SC16IS7XX_THR_REG, port->x_char); 627 port->icount.tx++; 628 port->x_char = 0; 629 return; 630 } 631 632 if (uart_circ_empty(xmit) || uart_tx_stopped(port)) 633 return; 634 635 /* Get length of data pending in circular buffer */ 636 to_send = uart_circ_chars_pending(xmit); 637 if (likely(to_send)) { 638 /* Limit to size of TX FIFO */ 639 txlen = sc16is7xx_port_read(port, SC16IS7XX_TXLVL_REG); 640 if (txlen > SC16IS7XX_FIFO_SIZE) { 641 dev_err_ratelimited(port->dev, 642 "chip reports %d free bytes in TX fifo, but it only has %d", 643 txlen, SC16IS7XX_FIFO_SIZE); 644 txlen = 0; 645 } 646 to_send = (to_send > txlen) ? txlen : to_send; 647 648 /* Add data to send */ 649 port->icount.tx += to_send; 650 651 /* Convert to linear buffer */ 652 for (i = 0; i < to_send; ++i) { 653 s->buf[i] = xmit->buf[xmit->tail]; 654 xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1); 655 } 656 657 sc16is7xx_fifo_write(port, to_send); 658 } 659 660 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) 661 uart_write_wakeup(port); 662 } 663 664 static void sc16is7xx_port_irq(struct sc16is7xx_port *s, int portno) 665 { 666 struct uart_port *port = &s->p[portno].port; 667 668 do { 669 unsigned int iir, rxlen; 670 671 iir = sc16is7xx_port_read(port, SC16IS7XX_IIR_REG); 672 if (iir & SC16IS7XX_IIR_NO_INT_BIT) 673 break; 674 675 iir &= SC16IS7XX_IIR_ID_MASK; 676 677 switch (iir) { 678 case SC16IS7XX_IIR_RDI_SRC: 679 case SC16IS7XX_IIR_RLSE_SRC: 680 case SC16IS7XX_IIR_RTOI_SRC: 681 case SC16IS7XX_IIR_XOFFI_SRC: 682 rxlen = sc16is7xx_port_read(port, SC16IS7XX_RXLVL_REG); 683 if (rxlen) 684 sc16is7xx_handle_rx(port, rxlen, iir); 685 break; 686 case SC16IS7XX_IIR_THRI_SRC: 687 sc16is7xx_handle_tx(port); 688 break; 689 default: 690 dev_err_ratelimited(port->dev, 691 "ttySC%i: Unexpected interrupt: %x", 692 port->line, iir); 693 break; 694 } 695 } while (1); 696 } 697 698 static void sc16is7xx_ist(struct kthread_work *ws) 699 { 700 struct sc16is7xx_port *s = to_sc16is7xx_port(ws, irq_work); 701 int i; 702 703 for (i = 0; i < s->devtype->nr_uart; ++i) 704 sc16is7xx_port_irq(s, i); 705 } 706 707 static irqreturn_t sc16is7xx_irq(int irq, void *dev_id) 708 { 709 struct sc16is7xx_port *s = (struct sc16is7xx_port *)dev_id; 710 711 kthread_queue_work(&s->kworker, &s->irq_work); 712 713 return IRQ_HANDLED; 714 } 715 716 static void sc16is7xx_tx_proc(struct kthread_work *ws) 717 { 718 struct uart_port *port = &(to_sc16is7xx_one(ws, tx_work)->port); 719 720 if ((port->rs485.flags & SER_RS485_ENABLED) && 721 (port->rs485.delay_rts_before_send > 0)) 722 msleep(port->rs485.delay_rts_before_send); 723 724 sc16is7xx_handle_tx(port); 725 } 726 727 static void sc16is7xx_reconf_rs485(struct uart_port *port) 728 { 729 const u32 mask = SC16IS7XX_EFCR_AUTO_RS485_BIT | 730 SC16IS7XX_EFCR_RTS_INVERT_BIT; 731 u32 efcr = 0; 732 struct serial_rs485 *rs485 = &port->rs485; 733 unsigned long irqflags; 734 735 spin_lock_irqsave(&port->lock, irqflags); 736 if (rs485->flags & SER_RS485_ENABLED) { 737 efcr |= SC16IS7XX_EFCR_AUTO_RS485_BIT; 738 739 if (rs485->flags & SER_RS485_RTS_AFTER_SEND) 740 efcr |= SC16IS7XX_EFCR_RTS_INVERT_BIT; 741 } 742 spin_unlock_irqrestore(&port->lock, irqflags); 743 744 sc16is7xx_port_update(port, SC16IS7XX_EFCR_REG, mask, efcr); 745 } 746 747 static void sc16is7xx_reg_proc(struct kthread_work *ws) 748 { 749 struct sc16is7xx_one *one = to_sc16is7xx_one(ws, reg_work); 750 struct sc16is7xx_one_config config; 751 unsigned long irqflags; 752 753 spin_lock_irqsave(&one->port.lock, irqflags); 754 config = one->config; 755 memset(&one->config, 0, sizeof(one->config)); 756 spin_unlock_irqrestore(&one->port.lock, irqflags); 757 758 if (config.flags & SC16IS7XX_RECONF_MD) { 759 sc16is7xx_port_update(&one->port, SC16IS7XX_MCR_REG, 760 SC16IS7XX_MCR_LOOP_BIT, 761 (one->port.mctrl & TIOCM_LOOP) ? 762 SC16IS7XX_MCR_LOOP_BIT : 0); 763 sc16is7xx_port_update(&one->port, SC16IS7XX_MCR_REG, 764 SC16IS7XX_MCR_RTS_BIT, 765 (one->port.mctrl & TIOCM_RTS) ? 766 SC16IS7XX_MCR_RTS_BIT : 0); 767 sc16is7xx_port_update(&one->port, SC16IS7XX_MCR_REG, 768 SC16IS7XX_MCR_DTR_BIT, 769 (one->port.mctrl & TIOCM_DTR) ? 770 SC16IS7XX_MCR_DTR_BIT : 0); 771 } 772 if (config.flags & SC16IS7XX_RECONF_IER) 773 sc16is7xx_port_update(&one->port, SC16IS7XX_IER_REG, 774 config.ier_clear, 0); 775 776 if (config.flags & SC16IS7XX_RECONF_RS485) 777 sc16is7xx_reconf_rs485(&one->port); 778 } 779 780 static void sc16is7xx_ier_clear(struct uart_port *port, u8 bit) 781 { 782 struct sc16is7xx_port *s = dev_get_drvdata(port->dev); 783 struct sc16is7xx_one *one = to_sc16is7xx_one(port, port); 784 785 one->config.flags |= SC16IS7XX_RECONF_IER; 786 one->config.ier_clear |= bit; 787 kthread_queue_work(&s->kworker, &one->reg_work); 788 } 789 790 static void sc16is7xx_stop_tx(struct uart_port *port) 791 { 792 sc16is7xx_ier_clear(port, SC16IS7XX_IER_THRI_BIT); 793 } 794 795 static void sc16is7xx_stop_rx(struct uart_port *port) 796 { 797 sc16is7xx_ier_clear(port, SC16IS7XX_IER_RDI_BIT); 798 } 799 800 static void sc16is7xx_start_tx(struct uart_port *port) 801 { 802 struct sc16is7xx_port *s = dev_get_drvdata(port->dev); 803 struct sc16is7xx_one *one = to_sc16is7xx_one(port, port); 804 805 kthread_queue_work(&s->kworker, &one->tx_work); 806 } 807 808 static unsigned int sc16is7xx_tx_empty(struct uart_port *port) 809 { 810 unsigned int lsr; 811 812 lsr = sc16is7xx_port_read(port, SC16IS7XX_LSR_REG); 813 814 return (lsr & SC16IS7XX_LSR_TEMT_BIT) ? TIOCSER_TEMT : 0; 815 } 816 817 static unsigned int sc16is7xx_get_mctrl(struct uart_port *port) 818 { 819 /* DCD and DSR are not wired and CTS/RTS is handled automatically 820 * so just indicate DSR and CAR asserted 821 */ 822 return TIOCM_DSR | TIOCM_CAR; 823 } 824 825 static void sc16is7xx_set_mctrl(struct uart_port *port, unsigned int mctrl) 826 { 827 struct sc16is7xx_port *s = dev_get_drvdata(port->dev); 828 struct sc16is7xx_one *one = to_sc16is7xx_one(port, port); 829 830 one->config.flags |= SC16IS7XX_RECONF_MD; 831 kthread_queue_work(&s->kworker, &one->reg_work); 832 } 833 834 static void sc16is7xx_break_ctl(struct uart_port *port, int break_state) 835 { 836 sc16is7xx_port_update(port, SC16IS7XX_LCR_REG, 837 SC16IS7XX_LCR_TXBREAK_BIT, 838 break_state ? SC16IS7XX_LCR_TXBREAK_BIT : 0); 839 } 840 841 static void sc16is7xx_set_termios(struct uart_port *port, 842 struct ktermios *termios, 843 struct ktermios *old) 844 { 845 struct sc16is7xx_port *s = dev_get_drvdata(port->dev); 846 unsigned int lcr, flow = 0; 847 int baud; 848 849 /* Mask termios capabilities we don't support */ 850 termios->c_cflag &= ~CMSPAR; 851 852 /* Word size */ 853 switch (termios->c_cflag & CSIZE) { 854 case CS5: 855 lcr = SC16IS7XX_LCR_WORD_LEN_5; 856 break; 857 case CS6: 858 lcr = SC16IS7XX_LCR_WORD_LEN_6; 859 break; 860 case CS7: 861 lcr = SC16IS7XX_LCR_WORD_LEN_7; 862 break; 863 case CS8: 864 lcr = SC16IS7XX_LCR_WORD_LEN_8; 865 break; 866 default: 867 lcr = SC16IS7XX_LCR_WORD_LEN_8; 868 termios->c_cflag &= ~CSIZE; 869 termios->c_cflag |= CS8; 870 break; 871 } 872 873 /* Parity */ 874 if (termios->c_cflag & PARENB) { 875 lcr |= SC16IS7XX_LCR_PARITY_BIT; 876 if (!(termios->c_cflag & PARODD)) 877 lcr |= SC16IS7XX_LCR_EVENPARITY_BIT; 878 } 879 880 /* Stop bits */ 881 if (termios->c_cflag & CSTOPB) 882 lcr |= SC16IS7XX_LCR_STOPLEN_BIT; /* 2 stops */ 883 884 /* Set read status mask */ 885 port->read_status_mask = SC16IS7XX_LSR_OE_BIT; 886 if (termios->c_iflag & INPCK) 887 port->read_status_mask |= SC16IS7XX_LSR_PE_BIT | 888 SC16IS7XX_LSR_FE_BIT; 889 if (termios->c_iflag & (BRKINT | PARMRK)) 890 port->read_status_mask |= SC16IS7XX_LSR_BI_BIT; 891 892 /* Set status ignore mask */ 893 port->ignore_status_mask = 0; 894 if (termios->c_iflag & IGNBRK) 895 port->ignore_status_mask |= SC16IS7XX_LSR_BI_BIT; 896 if (!(termios->c_cflag & CREAD)) 897 port->ignore_status_mask |= SC16IS7XX_LSR_BRK_ERROR_MASK; 898 899 sc16is7xx_port_write(port, SC16IS7XX_LCR_REG, 900 SC16IS7XX_LCR_CONF_MODE_B); 901 902 /* Configure flow control */ 903 regcache_cache_bypass(s->regmap, true); 904 sc16is7xx_port_write(port, SC16IS7XX_XON1_REG, termios->c_cc[VSTART]); 905 sc16is7xx_port_write(port, SC16IS7XX_XOFF1_REG, termios->c_cc[VSTOP]); 906 if (termios->c_cflag & CRTSCTS) 907 flow |= SC16IS7XX_EFR_AUTOCTS_BIT | 908 SC16IS7XX_EFR_AUTORTS_BIT; 909 if (termios->c_iflag & IXON) 910 flow |= SC16IS7XX_EFR_SWFLOW3_BIT; 911 if (termios->c_iflag & IXOFF) 912 flow |= SC16IS7XX_EFR_SWFLOW1_BIT; 913 914 sc16is7xx_port_write(port, SC16IS7XX_EFR_REG, flow); 915 regcache_cache_bypass(s->regmap, false); 916 917 /* Update LCR register */ 918 sc16is7xx_port_write(port, SC16IS7XX_LCR_REG, lcr); 919 920 /* Get baud rate generator configuration */ 921 baud = uart_get_baud_rate(port, termios, old, 922 port->uartclk / 16 / 4 / 0xffff, 923 port->uartclk / 16); 924 925 /* Setup baudrate generator */ 926 baud = sc16is7xx_set_baud(port, baud); 927 928 /* Update timeout according to new baud rate */ 929 uart_update_timeout(port, termios->c_cflag, baud); 930 } 931 932 static int sc16is7xx_config_rs485(struct uart_port *port, 933 struct serial_rs485 *rs485) 934 { 935 struct sc16is7xx_port *s = dev_get_drvdata(port->dev); 936 struct sc16is7xx_one *one = to_sc16is7xx_one(port, port); 937 938 if (rs485->flags & SER_RS485_ENABLED) { 939 bool rts_during_rx, rts_during_tx; 940 941 rts_during_rx = rs485->flags & SER_RS485_RTS_AFTER_SEND; 942 rts_during_tx = rs485->flags & SER_RS485_RTS_ON_SEND; 943 944 if (rts_during_rx == rts_during_tx) 945 dev_err(port->dev, 946 "unsupported RTS signalling on_send:%d after_send:%d - exactly one of RS485 RTS flags should be set\n", 947 rts_during_tx, rts_during_rx); 948 949 /* 950 * RTS signal is handled by HW, it's timing can't be influenced. 951 * However, it's sometimes useful to delay TX even without RTS 952 * control therefore we try to handle .delay_rts_before_send. 953 */ 954 if (rs485->delay_rts_after_send) 955 return -EINVAL; 956 } 957 958 port->rs485 = *rs485; 959 one->config.flags |= SC16IS7XX_RECONF_RS485; 960 kthread_queue_work(&s->kworker, &one->reg_work); 961 962 return 0; 963 } 964 965 static int sc16is7xx_startup(struct uart_port *port) 966 { 967 struct sc16is7xx_port *s = dev_get_drvdata(port->dev); 968 unsigned int val; 969 970 sc16is7xx_power(port, 1); 971 972 /* Reset FIFOs*/ 973 val = SC16IS7XX_FCR_RXRESET_BIT | SC16IS7XX_FCR_TXRESET_BIT; 974 sc16is7xx_port_write(port, SC16IS7XX_FCR_REG, val); 975 udelay(5); 976 sc16is7xx_port_write(port, SC16IS7XX_FCR_REG, 977 SC16IS7XX_FCR_FIFO_BIT); 978 979 /* Enable EFR */ 980 sc16is7xx_port_write(port, SC16IS7XX_LCR_REG, 981 SC16IS7XX_LCR_CONF_MODE_B); 982 983 regcache_cache_bypass(s->regmap, true); 984 985 /* Enable write access to enhanced features and internal clock div */ 986 sc16is7xx_port_write(port, SC16IS7XX_EFR_REG, 987 SC16IS7XX_EFR_ENABLE_BIT); 988 989 /* Enable TCR/TLR */ 990 sc16is7xx_port_update(port, SC16IS7XX_MCR_REG, 991 SC16IS7XX_MCR_TCRTLR_BIT, 992 SC16IS7XX_MCR_TCRTLR_BIT); 993 994 /* Configure flow control levels */ 995 /* Flow control halt level 48, resume level 24 */ 996 sc16is7xx_port_write(port, SC16IS7XX_TCR_REG, 997 SC16IS7XX_TCR_RX_RESUME(24) | 998 SC16IS7XX_TCR_RX_HALT(48)); 999 1000 regcache_cache_bypass(s->regmap, false); 1001 1002 /* Now, initialize the UART */ 1003 sc16is7xx_port_write(port, SC16IS7XX_LCR_REG, SC16IS7XX_LCR_WORD_LEN_8); 1004 1005 /* Enable the Rx and Tx FIFO */ 1006 sc16is7xx_port_update(port, SC16IS7XX_EFCR_REG, 1007 SC16IS7XX_EFCR_RXDISABLE_BIT | 1008 SC16IS7XX_EFCR_TXDISABLE_BIT, 1009 0); 1010 1011 /* Enable RX, TX interrupts */ 1012 val = SC16IS7XX_IER_RDI_BIT | SC16IS7XX_IER_THRI_BIT; 1013 sc16is7xx_port_write(port, SC16IS7XX_IER_REG, val); 1014 1015 return 0; 1016 } 1017 1018 static void sc16is7xx_shutdown(struct uart_port *port) 1019 { 1020 struct sc16is7xx_port *s = dev_get_drvdata(port->dev); 1021 1022 /* Disable all interrupts */ 1023 sc16is7xx_port_write(port, SC16IS7XX_IER_REG, 0); 1024 /* Disable TX/RX */ 1025 sc16is7xx_port_update(port, SC16IS7XX_EFCR_REG, 1026 SC16IS7XX_EFCR_RXDISABLE_BIT | 1027 SC16IS7XX_EFCR_TXDISABLE_BIT, 1028 SC16IS7XX_EFCR_RXDISABLE_BIT | 1029 SC16IS7XX_EFCR_TXDISABLE_BIT); 1030 1031 sc16is7xx_power(port, 0); 1032 1033 kthread_flush_worker(&s->kworker); 1034 } 1035 1036 static const char *sc16is7xx_type(struct uart_port *port) 1037 { 1038 struct sc16is7xx_port *s = dev_get_drvdata(port->dev); 1039 1040 return (port->type == PORT_SC16IS7XX) ? s->devtype->name : NULL; 1041 } 1042 1043 static int sc16is7xx_request_port(struct uart_port *port) 1044 { 1045 /* Do nothing */ 1046 return 0; 1047 } 1048 1049 static void sc16is7xx_config_port(struct uart_port *port, int flags) 1050 { 1051 if (flags & UART_CONFIG_TYPE) 1052 port->type = PORT_SC16IS7XX; 1053 } 1054 1055 static int sc16is7xx_verify_port(struct uart_port *port, 1056 struct serial_struct *s) 1057 { 1058 if ((s->type != PORT_UNKNOWN) && (s->type != PORT_SC16IS7XX)) 1059 return -EINVAL; 1060 if (s->irq != port->irq) 1061 return -EINVAL; 1062 1063 return 0; 1064 } 1065 1066 static void sc16is7xx_pm(struct uart_port *port, unsigned int state, 1067 unsigned int oldstate) 1068 { 1069 sc16is7xx_power(port, (state == UART_PM_STATE_ON) ? 1 : 0); 1070 } 1071 1072 static void sc16is7xx_null_void(struct uart_port *port) 1073 { 1074 /* Do nothing */ 1075 } 1076 1077 static const struct uart_ops sc16is7xx_ops = { 1078 .tx_empty = sc16is7xx_tx_empty, 1079 .set_mctrl = sc16is7xx_set_mctrl, 1080 .get_mctrl = sc16is7xx_get_mctrl, 1081 .stop_tx = sc16is7xx_stop_tx, 1082 .start_tx = sc16is7xx_start_tx, 1083 .stop_rx = sc16is7xx_stop_rx, 1084 .break_ctl = sc16is7xx_break_ctl, 1085 .startup = sc16is7xx_startup, 1086 .shutdown = sc16is7xx_shutdown, 1087 .set_termios = sc16is7xx_set_termios, 1088 .type = sc16is7xx_type, 1089 .request_port = sc16is7xx_request_port, 1090 .release_port = sc16is7xx_null_void, 1091 .config_port = sc16is7xx_config_port, 1092 .verify_port = sc16is7xx_verify_port, 1093 .pm = sc16is7xx_pm, 1094 }; 1095 1096 #ifdef CONFIG_GPIOLIB 1097 static int sc16is7xx_gpio_get(struct gpio_chip *chip, unsigned offset) 1098 { 1099 unsigned int val; 1100 struct sc16is7xx_port *s = gpiochip_get_data(chip); 1101 struct uart_port *port = &s->p[0].port; 1102 1103 val = sc16is7xx_port_read(port, SC16IS7XX_IOSTATE_REG); 1104 1105 return !!(val & BIT(offset)); 1106 } 1107 1108 static void sc16is7xx_gpio_set(struct gpio_chip *chip, unsigned offset, int val) 1109 { 1110 struct sc16is7xx_port *s = gpiochip_get_data(chip); 1111 struct uart_port *port = &s->p[0].port; 1112 1113 sc16is7xx_port_update(port, SC16IS7XX_IOSTATE_REG, BIT(offset), 1114 val ? BIT(offset) : 0); 1115 } 1116 1117 static int sc16is7xx_gpio_direction_input(struct gpio_chip *chip, 1118 unsigned offset) 1119 { 1120 struct sc16is7xx_port *s = gpiochip_get_data(chip); 1121 struct uart_port *port = &s->p[0].port; 1122 1123 sc16is7xx_port_update(port, SC16IS7XX_IODIR_REG, BIT(offset), 0); 1124 1125 return 0; 1126 } 1127 1128 static int sc16is7xx_gpio_direction_output(struct gpio_chip *chip, 1129 unsigned offset, int val) 1130 { 1131 struct sc16is7xx_port *s = gpiochip_get_data(chip); 1132 struct uart_port *port = &s->p[0].port; 1133 1134 sc16is7xx_port_update(port, SC16IS7XX_IOSTATE_REG, BIT(offset), 1135 val ? BIT(offset) : 0); 1136 sc16is7xx_port_update(port, SC16IS7XX_IODIR_REG, BIT(offset), 1137 BIT(offset)); 1138 1139 return 0; 1140 } 1141 #endif 1142 1143 static int sc16is7xx_probe(struct device *dev, 1144 const struct sc16is7xx_devtype *devtype, 1145 struct regmap *regmap, int irq, unsigned long flags) 1146 { 1147 struct sched_param sched_param = { .sched_priority = MAX_RT_PRIO / 2 }; 1148 unsigned long freq, *pfreq = dev_get_platdata(dev); 1149 int i, ret; 1150 struct sc16is7xx_port *s; 1151 1152 if (IS_ERR(regmap)) 1153 return PTR_ERR(regmap); 1154 1155 /* Alloc port structure */ 1156 s = devm_kzalloc(dev, sizeof(*s) + 1157 sizeof(struct sc16is7xx_one) * devtype->nr_uart, 1158 GFP_KERNEL); 1159 if (!s) { 1160 dev_err(dev, "Error allocating port structure\n"); 1161 return -ENOMEM; 1162 } 1163 1164 s->clk = devm_clk_get(dev, NULL); 1165 if (IS_ERR(s->clk)) { 1166 if (pfreq) 1167 freq = *pfreq; 1168 else 1169 return PTR_ERR(s->clk); 1170 } else { 1171 clk_prepare_enable(s->clk); 1172 freq = clk_get_rate(s->clk); 1173 } 1174 1175 s->regmap = regmap; 1176 s->devtype = devtype; 1177 dev_set_drvdata(dev, s); 1178 1179 kthread_init_worker(&s->kworker); 1180 kthread_init_work(&s->irq_work, sc16is7xx_ist); 1181 s->kworker_task = kthread_run(kthread_worker_fn, &s->kworker, 1182 "sc16is7xx"); 1183 if (IS_ERR(s->kworker_task)) { 1184 ret = PTR_ERR(s->kworker_task); 1185 goto out_clk; 1186 } 1187 sched_setscheduler(s->kworker_task, SCHED_FIFO, &sched_param); 1188 1189 #ifdef CONFIG_GPIOLIB 1190 if (devtype->nr_gpio) { 1191 /* Setup GPIO cotroller */ 1192 s->gpio.owner = THIS_MODULE; 1193 s->gpio.parent = dev; 1194 s->gpio.label = dev_name(dev); 1195 s->gpio.direction_input = sc16is7xx_gpio_direction_input; 1196 s->gpio.get = sc16is7xx_gpio_get; 1197 s->gpio.direction_output = sc16is7xx_gpio_direction_output; 1198 s->gpio.set = sc16is7xx_gpio_set; 1199 s->gpio.base = -1; 1200 s->gpio.ngpio = devtype->nr_gpio; 1201 s->gpio.can_sleep = 1; 1202 ret = gpiochip_add_data(&s->gpio, s); 1203 if (ret) 1204 goto out_thread; 1205 } 1206 #endif 1207 1208 /* reset device, purging any pending irq / data */ 1209 regmap_write(s->regmap, SC16IS7XX_IOCONTROL_REG << SC16IS7XX_REG_SHIFT, 1210 SC16IS7XX_IOCONTROL_SRESET_BIT); 1211 1212 for (i = 0; i < devtype->nr_uart; ++i) { 1213 s->p[i].line = i; 1214 /* Initialize port data */ 1215 s->p[i].port.dev = dev; 1216 s->p[i].port.irq = irq; 1217 s->p[i].port.type = PORT_SC16IS7XX; 1218 s->p[i].port.fifosize = SC16IS7XX_FIFO_SIZE; 1219 s->p[i].port.flags = UPF_FIXED_TYPE | UPF_LOW_LATENCY; 1220 s->p[i].port.iotype = UPIO_PORT; 1221 s->p[i].port.uartclk = freq; 1222 s->p[i].port.rs485_config = sc16is7xx_config_rs485; 1223 s->p[i].port.ops = &sc16is7xx_ops; 1224 s->p[i].port.line = sc16is7xx_alloc_line(); 1225 if (s->p[i].port.line >= SC16IS7XX_MAX_DEVS) { 1226 ret = -ENOMEM; 1227 goto out_ports; 1228 } 1229 1230 /* Disable all interrupts */ 1231 sc16is7xx_port_write(&s->p[i].port, SC16IS7XX_IER_REG, 0); 1232 /* Disable TX/RX */ 1233 sc16is7xx_port_write(&s->p[i].port, SC16IS7XX_EFCR_REG, 1234 SC16IS7XX_EFCR_RXDISABLE_BIT | 1235 SC16IS7XX_EFCR_TXDISABLE_BIT); 1236 /* Initialize kthread work structs */ 1237 kthread_init_work(&s->p[i].tx_work, sc16is7xx_tx_proc); 1238 kthread_init_work(&s->p[i].reg_work, sc16is7xx_reg_proc); 1239 /* Register port */ 1240 uart_add_one_port(&sc16is7xx_uart, &s->p[i].port); 1241 1242 /* Enable EFR */ 1243 sc16is7xx_port_write(&s->p[i].port, SC16IS7XX_LCR_REG, 1244 SC16IS7XX_LCR_CONF_MODE_B); 1245 1246 regcache_cache_bypass(s->regmap, true); 1247 1248 /* Enable write access to enhanced features */ 1249 sc16is7xx_port_write(&s->p[i].port, SC16IS7XX_EFR_REG, 1250 SC16IS7XX_EFR_ENABLE_BIT); 1251 1252 regcache_cache_bypass(s->regmap, false); 1253 1254 /* Restore access to general registers */ 1255 sc16is7xx_port_write(&s->p[i].port, SC16IS7XX_LCR_REG, 0x00); 1256 1257 /* Go to suspend mode */ 1258 sc16is7xx_power(&s->p[i].port, 0); 1259 } 1260 1261 /* Setup interrupt */ 1262 ret = devm_request_irq(dev, irq, sc16is7xx_irq, 1263 IRQF_ONESHOT | flags, dev_name(dev), s); 1264 if (!ret) 1265 return 0; 1266 1267 out_ports: 1268 for (i--; i >= 0; i--) { 1269 uart_remove_one_port(&sc16is7xx_uart, &s->p[i].port); 1270 clear_bit(s->p[i].port.line, &sc16is7xx_lines); 1271 } 1272 1273 #ifdef CONFIG_GPIOLIB 1274 if (devtype->nr_gpio) 1275 gpiochip_remove(&s->gpio); 1276 1277 out_thread: 1278 #endif 1279 kthread_stop(s->kworker_task); 1280 1281 out_clk: 1282 if (!IS_ERR(s->clk)) 1283 clk_disable_unprepare(s->clk); 1284 1285 return ret; 1286 } 1287 1288 static int sc16is7xx_remove(struct device *dev) 1289 { 1290 struct sc16is7xx_port *s = dev_get_drvdata(dev); 1291 int i; 1292 1293 #ifdef CONFIG_GPIOLIB 1294 if (s->devtype->nr_gpio) 1295 gpiochip_remove(&s->gpio); 1296 #endif 1297 1298 for (i = 0; i < s->devtype->nr_uart; i++) { 1299 uart_remove_one_port(&sc16is7xx_uart, &s->p[i].port); 1300 clear_bit(s->p[i].port.line, &sc16is7xx_lines); 1301 sc16is7xx_power(&s->p[i].port, 0); 1302 } 1303 1304 kthread_flush_worker(&s->kworker); 1305 kthread_stop(s->kworker_task); 1306 1307 if (!IS_ERR(s->clk)) 1308 clk_disable_unprepare(s->clk); 1309 1310 return 0; 1311 } 1312 1313 static const struct of_device_id __maybe_unused sc16is7xx_dt_ids[] = { 1314 { .compatible = "nxp,sc16is740", .data = &sc16is74x_devtype, }, 1315 { .compatible = "nxp,sc16is741", .data = &sc16is74x_devtype, }, 1316 { .compatible = "nxp,sc16is750", .data = &sc16is750_devtype, }, 1317 { .compatible = "nxp,sc16is752", .data = &sc16is752_devtype, }, 1318 { .compatible = "nxp,sc16is760", .data = &sc16is760_devtype, }, 1319 { .compatible = "nxp,sc16is762", .data = &sc16is762_devtype, }, 1320 { } 1321 }; 1322 MODULE_DEVICE_TABLE(of, sc16is7xx_dt_ids); 1323 1324 static struct regmap_config regcfg = { 1325 .reg_bits = 7, 1326 .pad_bits = 1, 1327 .val_bits = 8, 1328 .cache_type = REGCACHE_RBTREE, 1329 .volatile_reg = sc16is7xx_regmap_volatile, 1330 .precious_reg = sc16is7xx_regmap_precious, 1331 }; 1332 1333 #ifdef CONFIG_SERIAL_SC16IS7XX_SPI 1334 static int sc16is7xx_spi_probe(struct spi_device *spi) 1335 { 1336 const struct sc16is7xx_devtype *devtype; 1337 unsigned long flags = 0; 1338 struct regmap *regmap; 1339 int ret; 1340 1341 /* Setup SPI bus */ 1342 spi->bits_per_word = 8; 1343 /* only supports mode 0 on SC16IS762 */ 1344 spi->mode = spi->mode ? : SPI_MODE_0; 1345 spi->max_speed_hz = spi->max_speed_hz ? : 15000000; 1346 ret = spi_setup(spi); 1347 if (ret) 1348 return ret; 1349 1350 if (spi->dev.of_node) { 1351 const struct of_device_id *of_id = 1352 of_match_device(sc16is7xx_dt_ids, &spi->dev); 1353 1354 if (!of_id) 1355 return -ENODEV; 1356 1357 devtype = (struct sc16is7xx_devtype *)of_id->data; 1358 } else { 1359 const struct spi_device_id *id_entry = spi_get_device_id(spi); 1360 1361 devtype = (struct sc16is7xx_devtype *)id_entry->driver_data; 1362 flags = IRQF_TRIGGER_FALLING; 1363 } 1364 1365 regcfg.max_register = (0xf << SC16IS7XX_REG_SHIFT) | 1366 (devtype->nr_uart - 1); 1367 regmap = devm_regmap_init_spi(spi, ®cfg); 1368 1369 return sc16is7xx_probe(&spi->dev, devtype, regmap, spi->irq, flags); 1370 } 1371 1372 static int sc16is7xx_spi_remove(struct spi_device *spi) 1373 { 1374 return sc16is7xx_remove(&spi->dev); 1375 } 1376 1377 static const struct spi_device_id sc16is7xx_spi_id_table[] = { 1378 { "sc16is74x", (kernel_ulong_t)&sc16is74x_devtype, }, 1379 { "sc16is740", (kernel_ulong_t)&sc16is74x_devtype, }, 1380 { "sc16is741", (kernel_ulong_t)&sc16is74x_devtype, }, 1381 { "sc16is750", (kernel_ulong_t)&sc16is750_devtype, }, 1382 { "sc16is752", (kernel_ulong_t)&sc16is752_devtype, }, 1383 { "sc16is760", (kernel_ulong_t)&sc16is760_devtype, }, 1384 { "sc16is762", (kernel_ulong_t)&sc16is762_devtype, }, 1385 { } 1386 }; 1387 1388 MODULE_DEVICE_TABLE(spi, sc16is7xx_spi_id_table); 1389 1390 static struct spi_driver sc16is7xx_spi_uart_driver = { 1391 .driver = { 1392 .name = SC16IS7XX_NAME, 1393 .of_match_table = of_match_ptr(sc16is7xx_dt_ids), 1394 }, 1395 .probe = sc16is7xx_spi_probe, 1396 .remove = sc16is7xx_spi_remove, 1397 .id_table = sc16is7xx_spi_id_table, 1398 }; 1399 1400 MODULE_ALIAS("spi:sc16is7xx"); 1401 #endif 1402 1403 #ifdef CONFIG_SERIAL_SC16IS7XX_I2C 1404 static int sc16is7xx_i2c_probe(struct i2c_client *i2c, 1405 const struct i2c_device_id *id) 1406 { 1407 const struct sc16is7xx_devtype *devtype; 1408 unsigned long flags = 0; 1409 struct regmap *regmap; 1410 1411 if (i2c->dev.of_node) { 1412 const struct of_device_id *of_id = 1413 of_match_device(sc16is7xx_dt_ids, &i2c->dev); 1414 1415 if (!of_id) 1416 return -ENODEV; 1417 1418 devtype = (struct sc16is7xx_devtype *)of_id->data; 1419 } else { 1420 devtype = (struct sc16is7xx_devtype *)id->driver_data; 1421 flags = IRQF_TRIGGER_FALLING; 1422 } 1423 1424 regcfg.max_register = (0xf << SC16IS7XX_REG_SHIFT) | 1425 (devtype->nr_uart - 1); 1426 regmap = devm_regmap_init_i2c(i2c, ®cfg); 1427 1428 return sc16is7xx_probe(&i2c->dev, devtype, regmap, i2c->irq, flags); 1429 } 1430 1431 static int sc16is7xx_i2c_remove(struct i2c_client *client) 1432 { 1433 return sc16is7xx_remove(&client->dev); 1434 } 1435 1436 static const struct i2c_device_id sc16is7xx_i2c_id_table[] = { 1437 { "sc16is74x", (kernel_ulong_t)&sc16is74x_devtype, }, 1438 { "sc16is740", (kernel_ulong_t)&sc16is74x_devtype, }, 1439 { "sc16is741", (kernel_ulong_t)&sc16is74x_devtype, }, 1440 { "sc16is750", (kernel_ulong_t)&sc16is750_devtype, }, 1441 { "sc16is752", (kernel_ulong_t)&sc16is752_devtype, }, 1442 { "sc16is760", (kernel_ulong_t)&sc16is760_devtype, }, 1443 { "sc16is762", (kernel_ulong_t)&sc16is762_devtype, }, 1444 { } 1445 }; 1446 MODULE_DEVICE_TABLE(i2c, sc16is7xx_i2c_id_table); 1447 1448 static struct i2c_driver sc16is7xx_i2c_uart_driver = { 1449 .driver = { 1450 .name = SC16IS7XX_NAME, 1451 .of_match_table = of_match_ptr(sc16is7xx_dt_ids), 1452 }, 1453 .probe = sc16is7xx_i2c_probe, 1454 .remove = sc16is7xx_i2c_remove, 1455 .id_table = sc16is7xx_i2c_id_table, 1456 }; 1457 1458 #endif 1459 1460 static int __init sc16is7xx_init(void) 1461 { 1462 int ret; 1463 1464 ret = uart_register_driver(&sc16is7xx_uart); 1465 if (ret) { 1466 pr_err("Registering UART driver failed\n"); 1467 return ret; 1468 } 1469 1470 #ifdef CONFIG_SERIAL_SC16IS7XX_I2C 1471 ret = i2c_add_driver(&sc16is7xx_i2c_uart_driver); 1472 if (ret < 0) { 1473 pr_err("failed to init sc16is7xx i2c --> %d\n", ret); 1474 return ret; 1475 } 1476 #endif 1477 1478 #ifdef CONFIG_SERIAL_SC16IS7XX_SPI 1479 ret = spi_register_driver(&sc16is7xx_spi_uart_driver); 1480 if (ret < 0) { 1481 pr_err("failed to init sc16is7xx spi --> %d\n", ret); 1482 return ret; 1483 } 1484 #endif 1485 return ret; 1486 } 1487 module_init(sc16is7xx_init); 1488 1489 static void __exit sc16is7xx_exit(void) 1490 { 1491 #ifdef CONFIG_SERIAL_SC16IS7XX_I2C 1492 i2c_del_driver(&sc16is7xx_i2c_uart_driver); 1493 #endif 1494 1495 #ifdef CONFIG_SERIAL_SC16IS7XX_SPI 1496 spi_unregister_driver(&sc16is7xx_spi_uart_driver); 1497 #endif 1498 uart_unregister_driver(&sc16is7xx_uart); 1499 } 1500 module_exit(sc16is7xx_exit); 1501 1502 MODULE_LICENSE("GPL"); 1503 MODULE_AUTHOR("Jon Ringle <jringle@gridpoint.com>"); 1504 MODULE_DESCRIPTION("SC16IS7XX serial driver"); 1505