1 // SPDX-License-Identifier: GPL-2.0+ 2 /* 3 * SC16IS7xx tty serial driver - Copyright (C) 2014 GridPoint 4 * Author: Jon Ringle <jringle@gridpoint.com> 5 * 6 * Based on max310x.c, by Alexander Shiyan <shc_work@mail.ru> 7 */ 8 9 #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt 10 11 #include <linux/bitops.h> 12 #include <linux/clk.h> 13 #include <linux/delay.h> 14 #include <linux/device.h> 15 #include <linux/gpio/driver.h> 16 #include <linux/i2c.h> 17 #include <linux/mod_devicetable.h> 18 #include <linux/module.h> 19 #include <linux/property.h> 20 #include <linux/regmap.h> 21 #include <linux/serial_core.h> 22 #include <linux/serial.h> 23 #include <linux/tty.h> 24 #include <linux/tty_flip.h> 25 #include <linux/spi/spi.h> 26 #include <linux/uaccess.h> 27 #include <uapi/linux/sched/types.h> 28 29 #define SC16IS7XX_NAME "sc16is7xx" 30 #define SC16IS7XX_MAX_DEVS 8 31 32 /* SC16IS7XX register definitions */ 33 #define SC16IS7XX_RHR_REG (0x00) /* RX FIFO */ 34 #define SC16IS7XX_THR_REG (0x00) /* TX FIFO */ 35 #define SC16IS7XX_IER_REG (0x01) /* Interrupt enable */ 36 #define SC16IS7XX_IIR_REG (0x02) /* Interrupt Identification */ 37 #define SC16IS7XX_FCR_REG (0x02) /* FIFO control */ 38 #define SC16IS7XX_LCR_REG (0x03) /* Line Control */ 39 #define SC16IS7XX_MCR_REG (0x04) /* Modem Control */ 40 #define SC16IS7XX_LSR_REG (0x05) /* Line Status */ 41 #define SC16IS7XX_MSR_REG (0x06) /* Modem Status */ 42 #define SC16IS7XX_SPR_REG (0x07) /* Scratch Pad */ 43 #define SC16IS7XX_TXLVL_REG (0x08) /* TX FIFO level */ 44 #define SC16IS7XX_RXLVL_REG (0x09) /* RX FIFO level */ 45 #define SC16IS7XX_IODIR_REG (0x0a) /* I/O Direction 46 * - only on 75x/76x 47 */ 48 #define SC16IS7XX_IOSTATE_REG (0x0b) /* I/O State 49 * - only on 75x/76x 50 */ 51 #define SC16IS7XX_IOINTENA_REG (0x0c) /* I/O Interrupt Enable 52 * - only on 75x/76x 53 */ 54 #define SC16IS7XX_IOCONTROL_REG (0x0e) /* I/O Control 55 * - only on 75x/76x 56 */ 57 #define SC16IS7XX_EFCR_REG (0x0f) /* Extra Features Control */ 58 59 /* TCR/TLR Register set: Only if ((MCR[2] == 1) && (EFR[4] == 1)) */ 60 #define SC16IS7XX_TCR_REG (0x06) /* Transmit control */ 61 #define SC16IS7XX_TLR_REG (0x07) /* Trigger level */ 62 63 /* Special Register set: Only if ((LCR[7] == 1) && (LCR != 0xBF)) */ 64 #define SC16IS7XX_DLL_REG (0x00) /* Divisor Latch Low */ 65 #define SC16IS7XX_DLH_REG (0x01) /* Divisor Latch High */ 66 67 /* Enhanced Register set: Only if (LCR == 0xBF) */ 68 #define SC16IS7XX_EFR_REG (0x02) /* Enhanced Features */ 69 #define SC16IS7XX_XON1_REG (0x04) /* Xon1 word */ 70 #define SC16IS7XX_XON2_REG (0x05) /* Xon2 word */ 71 #define SC16IS7XX_XOFF1_REG (0x06) /* Xoff1 word */ 72 #define SC16IS7XX_XOFF2_REG (0x07) /* Xoff2 word */ 73 74 /* IER register bits */ 75 #define SC16IS7XX_IER_RDI_BIT (1 << 0) /* Enable RX data interrupt */ 76 #define SC16IS7XX_IER_THRI_BIT (1 << 1) /* Enable TX holding register 77 * interrupt */ 78 #define SC16IS7XX_IER_RLSI_BIT (1 << 2) /* Enable RX line status 79 * interrupt */ 80 #define SC16IS7XX_IER_MSI_BIT (1 << 3) /* Enable Modem status 81 * interrupt */ 82 83 /* IER register bits - write only if (EFR[4] == 1) */ 84 #define SC16IS7XX_IER_SLEEP_BIT (1 << 4) /* Enable Sleep mode */ 85 #define SC16IS7XX_IER_XOFFI_BIT (1 << 5) /* Enable Xoff interrupt */ 86 #define SC16IS7XX_IER_RTSI_BIT (1 << 6) /* Enable nRTS interrupt */ 87 #define SC16IS7XX_IER_CTSI_BIT (1 << 7) /* Enable nCTS interrupt */ 88 89 /* FCR register bits */ 90 #define SC16IS7XX_FCR_FIFO_BIT (1 << 0) /* Enable FIFO */ 91 #define SC16IS7XX_FCR_RXRESET_BIT (1 << 1) /* Reset RX FIFO */ 92 #define SC16IS7XX_FCR_TXRESET_BIT (1 << 2) /* Reset TX FIFO */ 93 #define SC16IS7XX_FCR_RXLVLL_BIT (1 << 6) /* RX Trigger level LSB */ 94 #define SC16IS7XX_FCR_RXLVLH_BIT (1 << 7) /* RX Trigger level MSB */ 95 96 /* FCR register bits - write only if (EFR[4] == 1) */ 97 #define SC16IS7XX_FCR_TXLVLL_BIT (1 << 4) /* TX Trigger level LSB */ 98 #define SC16IS7XX_FCR_TXLVLH_BIT (1 << 5) /* TX Trigger level MSB */ 99 100 /* IIR register bits */ 101 #define SC16IS7XX_IIR_NO_INT_BIT (1 << 0) /* No interrupts pending */ 102 #define SC16IS7XX_IIR_ID_MASK 0x3e /* Mask for the interrupt ID */ 103 #define SC16IS7XX_IIR_THRI_SRC 0x02 /* TX holding register empty */ 104 #define SC16IS7XX_IIR_RDI_SRC 0x04 /* RX data interrupt */ 105 #define SC16IS7XX_IIR_RLSE_SRC 0x06 /* RX line status error */ 106 #define SC16IS7XX_IIR_RTOI_SRC 0x0c /* RX time-out interrupt */ 107 #define SC16IS7XX_IIR_MSI_SRC 0x00 /* Modem status interrupt 108 * - only on 75x/76x 109 */ 110 #define SC16IS7XX_IIR_INPIN_SRC 0x30 /* Input pin change of state 111 * - only on 75x/76x 112 */ 113 #define SC16IS7XX_IIR_XOFFI_SRC 0x10 /* Received Xoff */ 114 #define SC16IS7XX_IIR_CTSRTS_SRC 0x20 /* nCTS,nRTS change of state 115 * from active (LOW) 116 * to inactive (HIGH) 117 */ 118 /* LCR register bits */ 119 #define SC16IS7XX_LCR_LENGTH0_BIT (1 << 0) /* Word length bit 0 */ 120 #define SC16IS7XX_LCR_LENGTH1_BIT (1 << 1) /* Word length bit 1 121 * 122 * Word length bits table: 123 * 00 -> 5 bit words 124 * 01 -> 6 bit words 125 * 10 -> 7 bit words 126 * 11 -> 8 bit words 127 */ 128 #define SC16IS7XX_LCR_STOPLEN_BIT (1 << 2) /* STOP length bit 129 * 130 * STOP length bit table: 131 * 0 -> 1 stop bit 132 * 1 -> 1-1.5 stop bits if 133 * word length is 5, 134 * 2 stop bits otherwise 135 */ 136 #define SC16IS7XX_LCR_PARITY_BIT (1 << 3) /* Parity bit enable */ 137 #define SC16IS7XX_LCR_EVENPARITY_BIT (1 << 4) /* Even parity bit enable */ 138 #define SC16IS7XX_LCR_FORCEPARITY_BIT (1 << 5) /* 9-bit multidrop parity */ 139 #define SC16IS7XX_LCR_TXBREAK_BIT (1 << 6) /* TX break enable */ 140 #define SC16IS7XX_LCR_DLAB_BIT (1 << 7) /* Divisor Latch enable */ 141 #define SC16IS7XX_LCR_WORD_LEN_5 (0x00) 142 #define SC16IS7XX_LCR_WORD_LEN_6 (0x01) 143 #define SC16IS7XX_LCR_WORD_LEN_7 (0x02) 144 #define SC16IS7XX_LCR_WORD_LEN_8 (0x03) 145 #define SC16IS7XX_LCR_CONF_MODE_A SC16IS7XX_LCR_DLAB_BIT /* Special 146 * reg set */ 147 #define SC16IS7XX_LCR_CONF_MODE_B 0xBF /* Enhanced 148 * reg set */ 149 150 /* MCR register bits */ 151 #define SC16IS7XX_MCR_DTR_BIT (1 << 0) /* DTR complement 152 * - only on 75x/76x 153 */ 154 #define SC16IS7XX_MCR_RTS_BIT (1 << 1) /* RTS complement */ 155 #define SC16IS7XX_MCR_TCRTLR_BIT (1 << 2) /* TCR/TLR register enable */ 156 #define SC16IS7XX_MCR_LOOP_BIT (1 << 4) /* Enable loopback test mode */ 157 #define SC16IS7XX_MCR_XONANY_BIT (1 << 5) /* Enable Xon Any 158 * - write enabled 159 * if (EFR[4] == 1) 160 */ 161 #define SC16IS7XX_MCR_IRDA_BIT (1 << 6) /* Enable IrDA mode 162 * - write enabled 163 * if (EFR[4] == 1) 164 */ 165 #define SC16IS7XX_MCR_CLKSEL_BIT (1 << 7) /* Divide clock by 4 166 * - write enabled 167 * if (EFR[4] == 1) 168 */ 169 170 /* LSR register bits */ 171 #define SC16IS7XX_LSR_DR_BIT (1 << 0) /* Receiver data ready */ 172 #define SC16IS7XX_LSR_OE_BIT (1 << 1) /* Overrun Error */ 173 #define SC16IS7XX_LSR_PE_BIT (1 << 2) /* Parity Error */ 174 #define SC16IS7XX_LSR_FE_BIT (1 << 3) /* Frame Error */ 175 #define SC16IS7XX_LSR_BI_BIT (1 << 4) /* Break Interrupt */ 176 #define SC16IS7XX_LSR_BRK_ERROR_MASK 0x1E /* BI, FE, PE, OE bits */ 177 #define SC16IS7XX_LSR_THRE_BIT (1 << 5) /* TX holding register empty */ 178 #define SC16IS7XX_LSR_TEMT_BIT (1 << 6) /* Transmitter empty */ 179 #define SC16IS7XX_LSR_FIFOE_BIT (1 << 7) /* Fifo Error */ 180 181 /* MSR register bits */ 182 #define SC16IS7XX_MSR_DCTS_BIT (1 << 0) /* Delta CTS Clear To Send */ 183 #define SC16IS7XX_MSR_DDSR_BIT (1 << 1) /* Delta DSR Data Set Ready 184 * or (IO4) 185 * - only on 75x/76x 186 */ 187 #define SC16IS7XX_MSR_DRI_BIT (1 << 2) /* Delta RI Ring Indicator 188 * or (IO7) 189 * - only on 75x/76x 190 */ 191 #define SC16IS7XX_MSR_DCD_BIT (1 << 3) /* Delta CD Carrier Detect 192 * or (IO6) 193 * - only on 75x/76x 194 */ 195 #define SC16IS7XX_MSR_CTS_BIT (1 << 4) /* CTS */ 196 #define SC16IS7XX_MSR_DSR_BIT (1 << 5) /* DSR (IO4) 197 * - only on 75x/76x 198 */ 199 #define SC16IS7XX_MSR_RI_BIT (1 << 6) /* RI (IO7) 200 * - only on 75x/76x 201 */ 202 #define SC16IS7XX_MSR_CD_BIT (1 << 7) /* CD (IO6) 203 * - only on 75x/76x 204 */ 205 #define SC16IS7XX_MSR_DELTA_MASK 0x0F /* Any of the delta bits! */ 206 207 /* 208 * TCR register bits 209 * TCR trigger levels are available from 0 to 60 characters with a granularity 210 * of four. 211 * The programmer must program the TCR such that TCR[3:0] > TCR[7:4]. There is 212 * no built-in hardware check to make sure this condition is met. Also, the TCR 213 * must be programmed with this condition before auto RTS or software flow 214 * control is enabled to avoid spurious operation of the device. 215 */ 216 #define SC16IS7XX_TCR_RX_HALT(words) ((((words) / 4) & 0x0f) << 0) 217 #define SC16IS7XX_TCR_RX_RESUME(words) ((((words) / 4) & 0x0f) << 4) 218 219 /* 220 * TLR register bits 221 * If TLR[3:0] or TLR[7:4] are logical 0, the selectable trigger levels via the 222 * FIFO Control Register (FCR) are used for the transmit and receive FIFO 223 * trigger levels. Trigger levels from 4 characters to 60 characters are 224 * available with a granularity of four. 225 * 226 * When the trigger level setting in TLR is zero, the SC16IS740/750/760 uses the 227 * trigger level setting defined in FCR. If TLR has non-zero trigger level value 228 * the trigger level defined in FCR is discarded. This applies to both transmit 229 * FIFO and receive FIFO trigger level setting. 230 * 231 * When TLR is used for RX trigger level control, FCR[7:6] should be left at the 232 * default state, that is, '00'. 233 */ 234 #define SC16IS7XX_TLR_TX_TRIGGER(words) ((((words) / 4) & 0x0f) << 0) 235 #define SC16IS7XX_TLR_RX_TRIGGER(words) ((((words) / 4) & 0x0f) << 4) 236 237 /* IOControl register bits (Only 750/760) */ 238 #define SC16IS7XX_IOCONTROL_LATCH_BIT (1 << 0) /* Enable input latching */ 239 #define SC16IS7XX_IOCONTROL_MODEM_BIT (1 << 1) /* Enable GPIO[7:4] as modem pins */ 240 #define SC16IS7XX_IOCONTROL_SRESET_BIT (1 << 3) /* Software Reset */ 241 242 /* EFCR register bits */ 243 #define SC16IS7XX_EFCR_9BIT_MODE_BIT (1 << 0) /* Enable 9-bit or Multidrop 244 * mode (RS485) */ 245 #define SC16IS7XX_EFCR_RXDISABLE_BIT (1 << 1) /* Disable receiver */ 246 #define SC16IS7XX_EFCR_TXDISABLE_BIT (1 << 2) /* Disable transmitter */ 247 #define SC16IS7XX_EFCR_AUTO_RS485_BIT (1 << 4) /* Auto RS485 RTS direction */ 248 #define SC16IS7XX_EFCR_RTS_INVERT_BIT (1 << 5) /* RTS output inversion */ 249 #define SC16IS7XX_EFCR_IRDA_MODE_BIT (1 << 7) /* IrDA mode 250 * 0 = rate upto 115.2 kbit/s 251 * - Only 750/760 252 * 1 = rate upto 1.152 Mbit/s 253 * - Only 760 254 */ 255 256 /* EFR register bits */ 257 #define SC16IS7XX_EFR_AUTORTS_BIT (1 << 6) /* Auto RTS flow ctrl enable */ 258 #define SC16IS7XX_EFR_AUTOCTS_BIT (1 << 7) /* Auto CTS flow ctrl enable */ 259 #define SC16IS7XX_EFR_XOFF2_DETECT_BIT (1 << 5) /* Enable Xoff2 detection */ 260 #define SC16IS7XX_EFR_ENABLE_BIT (1 << 4) /* Enable enhanced functions 261 * and writing to IER[7:4], 262 * FCR[5:4], MCR[7:5] 263 */ 264 #define SC16IS7XX_EFR_SWFLOW3_BIT (1 << 3) /* SWFLOW bit 3 */ 265 #define SC16IS7XX_EFR_SWFLOW2_BIT (1 << 2) /* SWFLOW bit 2 266 * 267 * SWFLOW bits 3 & 2 table: 268 * 00 -> no transmitter flow 269 * control 270 * 01 -> transmitter generates 271 * XON2 and XOFF2 272 * 10 -> transmitter generates 273 * XON1 and XOFF1 274 * 11 -> transmitter generates 275 * XON1, XON2, XOFF1 and 276 * XOFF2 277 */ 278 #define SC16IS7XX_EFR_SWFLOW1_BIT (1 << 1) /* SWFLOW bit 2 */ 279 #define SC16IS7XX_EFR_SWFLOW0_BIT (1 << 0) /* SWFLOW bit 3 280 * 281 * SWFLOW bits 3 & 2 table: 282 * 00 -> no received flow 283 * control 284 * 01 -> receiver compares 285 * XON2 and XOFF2 286 * 10 -> receiver compares 287 * XON1 and XOFF1 288 * 11 -> receiver compares 289 * XON1, XON2, XOFF1 and 290 * XOFF2 291 */ 292 293 /* Misc definitions */ 294 #define SC16IS7XX_FIFO_SIZE (64) 295 #define SC16IS7XX_REG_SHIFT 2 296 297 struct sc16is7xx_devtype { 298 char name[10]; 299 int nr_gpio; 300 int nr_uart; 301 }; 302 303 #define SC16IS7XX_RECONF_MD (1 << 0) 304 #define SC16IS7XX_RECONF_IER (1 << 1) 305 #define SC16IS7XX_RECONF_RS485 (1 << 2) 306 307 struct sc16is7xx_one_config { 308 unsigned int flags; 309 u8 ier_clear; 310 }; 311 312 struct sc16is7xx_one { 313 struct uart_port port; 314 u8 line; 315 struct kthread_work tx_work; 316 struct kthread_work reg_work; 317 struct sc16is7xx_one_config config; 318 bool irda_mode; 319 }; 320 321 struct sc16is7xx_port { 322 const struct sc16is7xx_devtype *devtype; 323 struct regmap *regmap; 324 struct clk *clk; 325 #ifdef CONFIG_GPIOLIB 326 struct gpio_chip gpio; 327 #endif 328 unsigned char buf[SC16IS7XX_FIFO_SIZE]; 329 struct kthread_worker kworker; 330 struct task_struct *kworker_task; 331 struct mutex efr_lock; 332 struct sc16is7xx_one p[]; 333 }; 334 335 static unsigned long sc16is7xx_lines; 336 337 static struct uart_driver sc16is7xx_uart = { 338 .owner = THIS_MODULE, 339 .dev_name = "ttySC", 340 .nr = SC16IS7XX_MAX_DEVS, 341 }; 342 343 #define to_sc16is7xx_port(p,e) ((container_of((p), struct sc16is7xx_port, e))) 344 #define to_sc16is7xx_one(p,e) ((container_of((p), struct sc16is7xx_one, e))) 345 346 static int sc16is7xx_line(struct uart_port *port) 347 { 348 struct sc16is7xx_one *one = to_sc16is7xx_one(port, port); 349 350 return one->line; 351 } 352 353 static u8 sc16is7xx_port_read(struct uart_port *port, u8 reg) 354 { 355 struct sc16is7xx_port *s = dev_get_drvdata(port->dev); 356 unsigned int val = 0; 357 const u8 line = sc16is7xx_line(port); 358 359 regmap_read(s->regmap, (reg << SC16IS7XX_REG_SHIFT) | line, &val); 360 361 return val; 362 } 363 364 static void sc16is7xx_port_write(struct uart_port *port, u8 reg, u8 val) 365 { 366 struct sc16is7xx_port *s = dev_get_drvdata(port->dev); 367 const u8 line = sc16is7xx_line(port); 368 369 regmap_write(s->regmap, (reg << SC16IS7XX_REG_SHIFT) | line, val); 370 } 371 372 static void sc16is7xx_fifo_read(struct uart_port *port, unsigned int rxlen) 373 { 374 struct sc16is7xx_port *s = dev_get_drvdata(port->dev); 375 const u8 line = sc16is7xx_line(port); 376 u8 addr = (SC16IS7XX_RHR_REG << SC16IS7XX_REG_SHIFT) | line; 377 378 regcache_cache_bypass(s->regmap, true); 379 regmap_raw_read(s->regmap, addr, s->buf, rxlen); 380 regcache_cache_bypass(s->regmap, false); 381 } 382 383 static void sc16is7xx_fifo_write(struct uart_port *port, u8 to_send) 384 { 385 struct sc16is7xx_port *s = dev_get_drvdata(port->dev); 386 const u8 line = sc16is7xx_line(port); 387 u8 addr = (SC16IS7XX_THR_REG << SC16IS7XX_REG_SHIFT) | line; 388 389 /* 390 * Don't send zero-length data, at least on SPI it confuses the chip 391 * delivering wrong TXLVL data. 392 */ 393 if (unlikely(!to_send)) 394 return; 395 396 regcache_cache_bypass(s->regmap, true); 397 regmap_raw_write(s->regmap, addr, s->buf, to_send); 398 regcache_cache_bypass(s->regmap, false); 399 } 400 401 static void sc16is7xx_port_update(struct uart_port *port, u8 reg, 402 u8 mask, u8 val) 403 { 404 struct sc16is7xx_port *s = dev_get_drvdata(port->dev); 405 const u8 line = sc16is7xx_line(port); 406 407 regmap_update_bits(s->regmap, (reg << SC16IS7XX_REG_SHIFT) | line, 408 mask, val); 409 } 410 411 static int sc16is7xx_alloc_line(void) 412 { 413 int i; 414 415 BUILD_BUG_ON(SC16IS7XX_MAX_DEVS > BITS_PER_LONG); 416 417 for (i = 0; i < SC16IS7XX_MAX_DEVS; i++) 418 if (!test_and_set_bit(i, &sc16is7xx_lines)) 419 break; 420 421 return i; 422 } 423 424 static void sc16is7xx_power(struct uart_port *port, int on) 425 { 426 sc16is7xx_port_update(port, SC16IS7XX_IER_REG, 427 SC16IS7XX_IER_SLEEP_BIT, 428 on ? 0 : SC16IS7XX_IER_SLEEP_BIT); 429 } 430 431 static const struct sc16is7xx_devtype sc16is74x_devtype = { 432 .name = "SC16IS74X", 433 .nr_gpio = 0, 434 .nr_uart = 1, 435 }; 436 437 static const struct sc16is7xx_devtype sc16is750_devtype = { 438 .name = "SC16IS750", 439 .nr_gpio = 8, 440 .nr_uart = 1, 441 }; 442 443 static const struct sc16is7xx_devtype sc16is752_devtype = { 444 .name = "SC16IS752", 445 .nr_gpio = 8, 446 .nr_uart = 2, 447 }; 448 449 static const struct sc16is7xx_devtype sc16is760_devtype = { 450 .name = "SC16IS760", 451 .nr_gpio = 8, 452 .nr_uart = 1, 453 }; 454 455 static const struct sc16is7xx_devtype sc16is762_devtype = { 456 .name = "SC16IS762", 457 .nr_gpio = 8, 458 .nr_uart = 2, 459 }; 460 461 static bool sc16is7xx_regmap_volatile(struct device *dev, unsigned int reg) 462 { 463 switch (reg >> SC16IS7XX_REG_SHIFT) { 464 case SC16IS7XX_RHR_REG: 465 case SC16IS7XX_IIR_REG: 466 case SC16IS7XX_LSR_REG: 467 case SC16IS7XX_MSR_REG: 468 case SC16IS7XX_TXLVL_REG: 469 case SC16IS7XX_RXLVL_REG: 470 case SC16IS7XX_IOSTATE_REG: 471 return true; 472 default: 473 break; 474 } 475 476 return false; 477 } 478 479 static bool sc16is7xx_regmap_precious(struct device *dev, unsigned int reg) 480 { 481 switch (reg >> SC16IS7XX_REG_SHIFT) { 482 case SC16IS7XX_RHR_REG: 483 return true; 484 default: 485 break; 486 } 487 488 return false; 489 } 490 491 static int sc16is7xx_set_baud(struct uart_port *port, int baud) 492 { 493 struct sc16is7xx_port *s = dev_get_drvdata(port->dev); 494 u8 lcr; 495 u8 prescaler = 0; 496 unsigned long clk = port->uartclk, div = clk / 16 / baud; 497 498 if (div > 0xffff) { 499 prescaler = SC16IS7XX_MCR_CLKSEL_BIT; 500 div /= 4; 501 } 502 503 /* In an amazing feat of design, the Enhanced Features Register shares 504 * the address of the Interrupt Identification Register, and is 505 * switched in by writing a magic value (0xbf) to the Line Control 506 * Register. Any interrupt firing during this time will see the EFR 507 * where it expects the IIR to be, leading to "Unexpected interrupt" 508 * messages. 509 * 510 * Prevent this possibility by claiming a mutex while accessing the 511 * EFR, and claiming the same mutex from within the interrupt handler. 512 * This is similar to disabling the interrupt, but that doesn't work 513 * because the bulk of the interrupt processing is run as a workqueue 514 * job in thread context. 515 */ 516 mutex_lock(&s->efr_lock); 517 518 lcr = sc16is7xx_port_read(port, SC16IS7XX_LCR_REG); 519 520 /* Open the LCR divisors for configuration */ 521 sc16is7xx_port_write(port, SC16IS7XX_LCR_REG, 522 SC16IS7XX_LCR_CONF_MODE_B); 523 524 /* Enable enhanced features */ 525 regcache_cache_bypass(s->regmap, true); 526 sc16is7xx_port_write(port, SC16IS7XX_EFR_REG, 527 SC16IS7XX_EFR_ENABLE_BIT); 528 regcache_cache_bypass(s->regmap, false); 529 530 /* Put LCR back to the normal mode */ 531 sc16is7xx_port_write(port, SC16IS7XX_LCR_REG, lcr); 532 533 mutex_unlock(&s->efr_lock); 534 535 sc16is7xx_port_update(port, SC16IS7XX_MCR_REG, 536 SC16IS7XX_MCR_CLKSEL_BIT, 537 prescaler); 538 539 /* Open the LCR divisors for configuration */ 540 sc16is7xx_port_write(port, SC16IS7XX_LCR_REG, 541 SC16IS7XX_LCR_CONF_MODE_A); 542 543 /* Write the new divisor */ 544 regcache_cache_bypass(s->regmap, true); 545 sc16is7xx_port_write(port, SC16IS7XX_DLH_REG, div / 256); 546 sc16is7xx_port_write(port, SC16IS7XX_DLL_REG, div % 256); 547 regcache_cache_bypass(s->regmap, false); 548 549 /* Put LCR back to the normal mode */ 550 sc16is7xx_port_write(port, SC16IS7XX_LCR_REG, lcr); 551 552 return DIV_ROUND_CLOSEST(clk / 16, div); 553 } 554 555 static void sc16is7xx_handle_rx(struct uart_port *port, unsigned int rxlen, 556 unsigned int iir) 557 { 558 struct sc16is7xx_port *s = dev_get_drvdata(port->dev); 559 unsigned int lsr = 0, ch, flag, bytes_read, i; 560 bool read_lsr = (iir == SC16IS7XX_IIR_RLSE_SRC) ? true : false; 561 562 if (unlikely(rxlen >= sizeof(s->buf))) { 563 dev_warn_ratelimited(port->dev, 564 "ttySC%i: Possible RX FIFO overrun: %d\n", 565 port->line, rxlen); 566 port->icount.buf_overrun++; 567 /* Ensure sanity of RX level */ 568 rxlen = sizeof(s->buf); 569 } 570 571 while (rxlen) { 572 /* Only read lsr if there are possible errors in FIFO */ 573 if (read_lsr) { 574 lsr = sc16is7xx_port_read(port, SC16IS7XX_LSR_REG); 575 if (!(lsr & SC16IS7XX_LSR_FIFOE_BIT)) 576 read_lsr = false; /* No errors left in FIFO */ 577 } else 578 lsr = 0; 579 580 if (read_lsr) { 581 s->buf[0] = sc16is7xx_port_read(port, SC16IS7XX_RHR_REG); 582 bytes_read = 1; 583 } else { 584 sc16is7xx_fifo_read(port, rxlen); 585 bytes_read = rxlen; 586 } 587 588 lsr &= SC16IS7XX_LSR_BRK_ERROR_MASK; 589 590 port->icount.rx++; 591 flag = TTY_NORMAL; 592 593 if (unlikely(lsr)) { 594 if (lsr & SC16IS7XX_LSR_BI_BIT) { 595 port->icount.brk++; 596 if (uart_handle_break(port)) 597 continue; 598 } else if (lsr & SC16IS7XX_LSR_PE_BIT) 599 port->icount.parity++; 600 else if (lsr & SC16IS7XX_LSR_FE_BIT) 601 port->icount.frame++; 602 else if (lsr & SC16IS7XX_LSR_OE_BIT) 603 port->icount.overrun++; 604 605 lsr &= port->read_status_mask; 606 if (lsr & SC16IS7XX_LSR_BI_BIT) 607 flag = TTY_BREAK; 608 else if (lsr & SC16IS7XX_LSR_PE_BIT) 609 flag = TTY_PARITY; 610 else if (lsr & SC16IS7XX_LSR_FE_BIT) 611 flag = TTY_FRAME; 612 else if (lsr & SC16IS7XX_LSR_OE_BIT) 613 flag = TTY_OVERRUN; 614 } 615 616 for (i = 0; i < bytes_read; ++i) { 617 ch = s->buf[i]; 618 if (uart_handle_sysrq_char(port, ch)) 619 continue; 620 621 if (lsr & port->ignore_status_mask) 622 continue; 623 624 uart_insert_char(port, lsr, SC16IS7XX_LSR_OE_BIT, ch, 625 flag); 626 } 627 rxlen -= bytes_read; 628 } 629 630 tty_flip_buffer_push(&port->state->port); 631 } 632 633 static void sc16is7xx_handle_tx(struct uart_port *port) 634 { 635 struct sc16is7xx_port *s = dev_get_drvdata(port->dev); 636 struct circ_buf *xmit = &port->state->xmit; 637 unsigned int txlen, to_send, i; 638 639 if (unlikely(port->x_char)) { 640 sc16is7xx_port_write(port, SC16IS7XX_THR_REG, port->x_char); 641 port->icount.tx++; 642 port->x_char = 0; 643 return; 644 } 645 646 if (uart_circ_empty(xmit) || uart_tx_stopped(port)) 647 return; 648 649 /* Get length of data pending in circular buffer */ 650 to_send = uart_circ_chars_pending(xmit); 651 if (likely(to_send)) { 652 /* Limit to size of TX FIFO */ 653 txlen = sc16is7xx_port_read(port, SC16IS7XX_TXLVL_REG); 654 if (txlen > SC16IS7XX_FIFO_SIZE) { 655 dev_err_ratelimited(port->dev, 656 "chip reports %d free bytes in TX fifo, but it only has %d", 657 txlen, SC16IS7XX_FIFO_SIZE); 658 txlen = 0; 659 } 660 to_send = (to_send > txlen) ? txlen : to_send; 661 662 /* Add data to send */ 663 port->icount.tx += to_send; 664 665 /* Convert to linear buffer */ 666 for (i = 0; i < to_send; ++i) { 667 s->buf[i] = xmit->buf[xmit->tail]; 668 xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1); 669 } 670 671 sc16is7xx_fifo_write(port, to_send); 672 } 673 674 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) 675 uart_write_wakeup(port); 676 } 677 678 static bool sc16is7xx_port_irq(struct sc16is7xx_port *s, int portno) 679 { 680 struct uart_port *port = &s->p[portno].port; 681 682 do { 683 unsigned int iir, rxlen; 684 685 iir = sc16is7xx_port_read(port, SC16IS7XX_IIR_REG); 686 if (iir & SC16IS7XX_IIR_NO_INT_BIT) 687 return false; 688 689 iir &= SC16IS7XX_IIR_ID_MASK; 690 691 switch (iir) { 692 case SC16IS7XX_IIR_RDI_SRC: 693 case SC16IS7XX_IIR_RLSE_SRC: 694 case SC16IS7XX_IIR_RTOI_SRC: 695 case SC16IS7XX_IIR_XOFFI_SRC: 696 rxlen = sc16is7xx_port_read(port, SC16IS7XX_RXLVL_REG); 697 if (rxlen) 698 sc16is7xx_handle_rx(port, rxlen, iir); 699 break; 700 case SC16IS7XX_IIR_THRI_SRC: 701 sc16is7xx_handle_tx(port); 702 break; 703 default: 704 dev_err_ratelimited(port->dev, 705 "ttySC%i: Unexpected interrupt: %x", 706 port->line, iir); 707 break; 708 } 709 } while (0); 710 return true; 711 } 712 713 static irqreturn_t sc16is7xx_irq(int irq, void *dev_id) 714 { 715 struct sc16is7xx_port *s = (struct sc16is7xx_port *)dev_id; 716 717 mutex_lock(&s->efr_lock); 718 719 while (1) { 720 bool keep_polling = false; 721 int i; 722 723 for (i = 0; i < s->devtype->nr_uart; ++i) 724 keep_polling |= sc16is7xx_port_irq(s, i); 725 if (!keep_polling) 726 break; 727 } 728 729 mutex_unlock(&s->efr_lock); 730 731 return IRQ_HANDLED; 732 } 733 734 static void sc16is7xx_tx_proc(struct kthread_work *ws) 735 { 736 struct uart_port *port = &(to_sc16is7xx_one(ws, tx_work)->port); 737 738 if ((port->rs485.flags & SER_RS485_ENABLED) && 739 (port->rs485.delay_rts_before_send > 0)) 740 msleep(port->rs485.delay_rts_before_send); 741 742 sc16is7xx_handle_tx(port); 743 } 744 745 static void sc16is7xx_reconf_rs485(struct uart_port *port) 746 { 747 const u32 mask = SC16IS7XX_EFCR_AUTO_RS485_BIT | 748 SC16IS7XX_EFCR_RTS_INVERT_BIT; 749 u32 efcr = 0; 750 struct serial_rs485 *rs485 = &port->rs485; 751 unsigned long irqflags; 752 753 spin_lock_irqsave(&port->lock, irqflags); 754 if (rs485->flags & SER_RS485_ENABLED) { 755 efcr |= SC16IS7XX_EFCR_AUTO_RS485_BIT; 756 757 if (rs485->flags & SER_RS485_RTS_AFTER_SEND) 758 efcr |= SC16IS7XX_EFCR_RTS_INVERT_BIT; 759 } 760 spin_unlock_irqrestore(&port->lock, irqflags); 761 762 sc16is7xx_port_update(port, SC16IS7XX_EFCR_REG, mask, efcr); 763 } 764 765 static void sc16is7xx_reg_proc(struct kthread_work *ws) 766 { 767 struct sc16is7xx_one *one = to_sc16is7xx_one(ws, reg_work); 768 struct sc16is7xx_one_config config; 769 unsigned long irqflags; 770 771 spin_lock_irqsave(&one->port.lock, irqflags); 772 config = one->config; 773 memset(&one->config, 0, sizeof(one->config)); 774 spin_unlock_irqrestore(&one->port.lock, irqflags); 775 776 if (config.flags & SC16IS7XX_RECONF_MD) { 777 sc16is7xx_port_update(&one->port, SC16IS7XX_MCR_REG, 778 SC16IS7XX_MCR_LOOP_BIT, 779 (one->port.mctrl & TIOCM_LOOP) ? 780 SC16IS7XX_MCR_LOOP_BIT : 0); 781 sc16is7xx_port_update(&one->port, SC16IS7XX_MCR_REG, 782 SC16IS7XX_MCR_RTS_BIT, 783 (one->port.mctrl & TIOCM_RTS) ? 784 SC16IS7XX_MCR_RTS_BIT : 0); 785 sc16is7xx_port_update(&one->port, SC16IS7XX_MCR_REG, 786 SC16IS7XX_MCR_DTR_BIT, 787 (one->port.mctrl & TIOCM_DTR) ? 788 SC16IS7XX_MCR_DTR_BIT : 0); 789 } 790 if (config.flags & SC16IS7XX_RECONF_IER) 791 sc16is7xx_port_update(&one->port, SC16IS7XX_IER_REG, 792 config.ier_clear, 0); 793 794 if (config.flags & SC16IS7XX_RECONF_RS485) 795 sc16is7xx_reconf_rs485(&one->port); 796 } 797 798 static void sc16is7xx_ier_clear(struct uart_port *port, u8 bit) 799 { 800 struct sc16is7xx_port *s = dev_get_drvdata(port->dev); 801 struct sc16is7xx_one *one = to_sc16is7xx_one(port, port); 802 803 one->config.flags |= SC16IS7XX_RECONF_IER; 804 one->config.ier_clear |= bit; 805 kthread_queue_work(&s->kworker, &one->reg_work); 806 } 807 808 static void sc16is7xx_stop_tx(struct uart_port *port) 809 { 810 sc16is7xx_ier_clear(port, SC16IS7XX_IER_THRI_BIT); 811 } 812 813 static void sc16is7xx_stop_rx(struct uart_port *port) 814 { 815 sc16is7xx_ier_clear(port, SC16IS7XX_IER_RDI_BIT); 816 } 817 818 static void sc16is7xx_start_tx(struct uart_port *port) 819 { 820 struct sc16is7xx_port *s = dev_get_drvdata(port->dev); 821 struct sc16is7xx_one *one = to_sc16is7xx_one(port, port); 822 823 kthread_queue_work(&s->kworker, &one->tx_work); 824 } 825 826 static unsigned int sc16is7xx_tx_empty(struct uart_port *port) 827 { 828 unsigned int lsr; 829 830 lsr = sc16is7xx_port_read(port, SC16IS7XX_LSR_REG); 831 832 return (lsr & SC16IS7XX_LSR_TEMT_BIT) ? TIOCSER_TEMT : 0; 833 } 834 835 static unsigned int sc16is7xx_get_mctrl(struct uart_port *port) 836 { 837 /* DCD and DSR are not wired and CTS/RTS is handled automatically 838 * so just indicate DSR and CAR asserted 839 */ 840 return TIOCM_DSR | TIOCM_CAR; 841 } 842 843 static void sc16is7xx_set_mctrl(struct uart_port *port, unsigned int mctrl) 844 { 845 struct sc16is7xx_port *s = dev_get_drvdata(port->dev); 846 struct sc16is7xx_one *one = to_sc16is7xx_one(port, port); 847 848 one->config.flags |= SC16IS7XX_RECONF_MD; 849 kthread_queue_work(&s->kworker, &one->reg_work); 850 } 851 852 static void sc16is7xx_break_ctl(struct uart_port *port, int break_state) 853 { 854 sc16is7xx_port_update(port, SC16IS7XX_LCR_REG, 855 SC16IS7XX_LCR_TXBREAK_BIT, 856 break_state ? SC16IS7XX_LCR_TXBREAK_BIT : 0); 857 } 858 859 static void sc16is7xx_set_termios(struct uart_port *port, 860 struct ktermios *termios, 861 struct ktermios *old) 862 { 863 struct sc16is7xx_port *s = dev_get_drvdata(port->dev); 864 unsigned int lcr, flow = 0; 865 int baud; 866 867 /* Mask termios capabilities we don't support */ 868 termios->c_cflag &= ~CMSPAR; 869 870 /* Word size */ 871 switch (termios->c_cflag & CSIZE) { 872 case CS5: 873 lcr = SC16IS7XX_LCR_WORD_LEN_5; 874 break; 875 case CS6: 876 lcr = SC16IS7XX_LCR_WORD_LEN_6; 877 break; 878 case CS7: 879 lcr = SC16IS7XX_LCR_WORD_LEN_7; 880 break; 881 case CS8: 882 lcr = SC16IS7XX_LCR_WORD_LEN_8; 883 break; 884 default: 885 lcr = SC16IS7XX_LCR_WORD_LEN_8; 886 termios->c_cflag &= ~CSIZE; 887 termios->c_cflag |= CS8; 888 break; 889 } 890 891 /* Parity */ 892 if (termios->c_cflag & PARENB) { 893 lcr |= SC16IS7XX_LCR_PARITY_BIT; 894 if (!(termios->c_cflag & PARODD)) 895 lcr |= SC16IS7XX_LCR_EVENPARITY_BIT; 896 } 897 898 /* Stop bits */ 899 if (termios->c_cflag & CSTOPB) 900 lcr |= SC16IS7XX_LCR_STOPLEN_BIT; /* 2 stops */ 901 902 /* Set read status mask */ 903 port->read_status_mask = SC16IS7XX_LSR_OE_BIT; 904 if (termios->c_iflag & INPCK) 905 port->read_status_mask |= SC16IS7XX_LSR_PE_BIT | 906 SC16IS7XX_LSR_FE_BIT; 907 if (termios->c_iflag & (BRKINT | PARMRK)) 908 port->read_status_mask |= SC16IS7XX_LSR_BI_BIT; 909 910 /* Set status ignore mask */ 911 port->ignore_status_mask = 0; 912 if (termios->c_iflag & IGNBRK) 913 port->ignore_status_mask |= SC16IS7XX_LSR_BI_BIT; 914 if (!(termios->c_cflag & CREAD)) 915 port->ignore_status_mask |= SC16IS7XX_LSR_BRK_ERROR_MASK; 916 917 /* As above, claim the mutex while accessing the EFR. */ 918 mutex_lock(&s->efr_lock); 919 920 sc16is7xx_port_write(port, SC16IS7XX_LCR_REG, 921 SC16IS7XX_LCR_CONF_MODE_B); 922 923 /* Configure flow control */ 924 regcache_cache_bypass(s->regmap, true); 925 sc16is7xx_port_write(port, SC16IS7XX_XON1_REG, termios->c_cc[VSTART]); 926 sc16is7xx_port_write(port, SC16IS7XX_XOFF1_REG, termios->c_cc[VSTOP]); 927 if (termios->c_cflag & CRTSCTS) 928 flow |= SC16IS7XX_EFR_AUTOCTS_BIT | 929 SC16IS7XX_EFR_AUTORTS_BIT; 930 if (termios->c_iflag & IXON) 931 flow |= SC16IS7XX_EFR_SWFLOW3_BIT; 932 if (termios->c_iflag & IXOFF) 933 flow |= SC16IS7XX_EFR_SWFLOW1_BIT; 934 935 sc16is7xx_port_write(port, SC16IS7XX_EFR_REG, flow); 936 regcache_cache_bypass(s->regmap, false); 937 938 /* Update LCR register */ 939 sc16is7xx_port_write(port, SC16IS7XX_LCR_REG, lcr); 940 941 mutex_unlock(&s->efr_lock); 942 943 /* Get baud rate generator configuration */ 944 baud = uart_get_baud_rate(port, termios, old, 945 port->uartclk / 16 / 4 / 0xffff, 946 port->uartclk / 16); 947 948 /* Setup baudrate generator */ 949 baud = sc16is7xx_set_baud(port, baud); 950 951 /* Update timeout according to new baud rate */ 952 uart_update_timeout(port, termios->c_cflag, baud); 953 } 954 955 static int sc16is7xx_config_rs485(struct uart_port *port, 956 struct serial_rs485 *rs485) 957 { 958 struct sc16is7xx_port *s = dev_get_drvdata(port->dev); 959 struct sc16is7xx_one *one = to_sc16is7xx_one(port, port); 960 961 if (rs485->flags & SER_RS485_ENABLED) { 962 bool rts_during_rx, rts_during_tx; 963 964 rts_during_rx = rs485->flags & SER_RS485_RTS_AFTER_SEND; 965 rts_during_tx = rs485->flags & SER_RS485_RTS_ON_SEND; 966 967 if (rts_during_rx == rts_during_tx) 968 dev_err(port->dev, 969 "unsupported RTS signalling on_send:%d after_send:%d - exactly one of RS485 RTS flags should be set\n", 970 rts_during_tx, rts_during_rx); 971 972 /* 973 * RTS signal is handled by HW, it's timing can't be influenced. 974 * However, it's sometimes useful to delay TX even without RTS 975 * control therefore we try to handle .delay_rts_before_send. 976 */ 977 if (rs485->delay_rts_after_send) 978 return -EINVAL; 979 } 980 981 port->rs485 = *rs485; 982 one->config.flags |= SC16IS7XX_RECONF_RS485; 983 kthread_queue_work(&s->kworker, &one->reg_work); 984 985 return 0; 986 } 987 988 static int sc16is7xx_startup(struct uart_port *port) 989 { 990 struct sc16is7xx_one *one = to_sc16is7xx_one(port, port); 991 struct sc16is7xx_port *s = dev_get_drvdata(port->dev); 992 unsigned int val; 993 994 sc16is7xx_power(port, 1); 995 996 /* Reset FIFOs*/ 997 val = SC16IS7XX_FCR_RXRESET_BIT | SC16IS7XX_FCR_TXRESET_BIT; 998 sc16is7xx_port_write(port, SC16IS7XX_FCR_REG, val); 999 udelay(5); 1000 sc16is7xx_port_write(port, SC16IS7XX_FCR_REG, 1001 SC16IS7XX_FCR_FIFO_BIT); 1002 1003 /* Enable EFR */ 1004 sc16is7xx_port_write(port, SC16IS7XX_LCR_REG, 1005 SC16IS7XX_LCR_CONF_MODE_B); 1006 1007 regcache_cache_bypass(s->regmap, true); 1008 1009 /* Enable write access to enhanced features and internal clock div */ 1010 sc16is7xx_port_write(port, SC16IS7XX_EFR_REG, 1011 SC16IS7XX_EFR_ENABLE_BIT); 1012 1013 /* Enable TCR/TLR */ 1014 sc16is7xx_port_update(port, SC16IS7XX_MCR_REG, 1015 SC16IS7XX_MCR_TCRTLR_BIT, 1016 SC16IS7XX_MCR_TCRTLR_BIT); 1017 1018 /* Configure flow control levels */ 1019 /* Flow control halt level 48, resume level 24 */ 1020 sc16is7xx_port_write(port, SC16IS7XX_TCR_REG, 1021 SC16IS7XX_TCR_RX_RESUME(24) | 1022 SC16IS7XX_TCR_RX_HALT(48)); 1023 1024 regcache_cache_bypass(s->regmap, false); 1025 1026 /* Now, initialize the UART */ 1027 sc16is7xx_port_write(port, SC16IS7XX_LCR_REG, SC16IS7XX_LCR_WORD_LEN_8); 1028 1029 /* Enable IrDA mode if requested in DT */ 1030 /* This bit must be written with LCR[7] = 0 */ 1031 sc16is7xx_port_update(port, SC16IS7XX_MCR_REG, 1032 SC16IS7XX_MCR_IRDA_BIT, 1033 one->irda_mode ? 1034 SC16IS7XX_MCR_IRDA_BIT : 0); 1035 1036 /* Enable the Rx and Tx FIFO */ 1037 sc16is7xx_port_update(port, SC16IS7XX_EFCR_REG, 1038 SC16IS7XX_EFCR_RXDISABLE_BIT | 1039 SC16IS7XX_EFCR_TXDISABLE_BIT, 1040 0); 1041 1042 /* Enable RX, TX interrupts */ 1043 val = SC16IS7XX_IER_RDI_BIT | SC16IS7XX_IER_THRI_BIT; 1044 sc16is7xx_port_write(port, SC16IS7XX_IER_REG, val); 1045 1046 return 0; 1047 } 1048 1049 static void sc16is7xx_shutdown(struct uart_port *port) 1050 { 1051 struct sc16is7xx_port *s = dev_get_drvdata(port->dev); 1052 1053 /* Disable all interrupts */ 1054 sc16is7xx_port_write(port, SC16IS7XX_IER_REG, 0); 1055 /* Disable TX/RX */ 1056 sc16is7xx_port_update(port, SC16IS7XX_EFCR_REG, 1057 SC16IS7XX_EFCR_RXDISABLE_BIT | 1058 SC16IS7XX_EFCR_TXDISABLE_BIT, 1059 SC16IS7XX_EFCR_RXDISABLE_BIT | 1060 SC16IS7XX_EFCR_TXDISABLE_BIT); 1061 1062 sc16is7xx_power(port, 0); 1063 1064 kthread_flush_worker(&s->kworker); 1065 } 1066 1067 static const char *sc16is7xx_type(struct uart_port *port) 1068 { 1069 struct sc16is7xx_port *s = dev_get_drvdata(port->dev); 1070 1071 return (port->type == PORT_SC16IS7XX) ? s->devtype->name : NULL; 1072 } 1073 1074 static int sc16is7xx_request_port(struct uart_port *port) 1075 { 1076 /* Do nothing */ 1077 return 0; 1078 } 1079 1080 static void sc16is7xx_config_port(struct uart_port *port, int flags) 1081 { 1082 if (flags & UART_CONFIG_TYPE) 1083 port->type = PORT_SC16IS7XX; 1084 } 1085 1086 static int sc16is7xx_verify_port(struct uart_port *port, 1087 struct serial_struct *s) 1088 { 1089 if ((s->type != PORT_UNKNOWN) && (s->type != PORT_SC16IS7XX)) 1090 return -EINVAL; 1091 if (s->irq != port->irq) 1092 return -EINVAL; 1093 1094 return 0; 1095 } 1096 1097 static void sc16is7xx_pm(struct uart_port *port, unsigned int state, 1098 unsigned int oldstate) 1099 { 1100 sc16is7xx_power(port, (state == UART_PM_STATE_ON) ? 1 : 0); 1101 } 1102 1103 static void sc16is7xx_null_void(struct uart_port *port) 1104 { 1105 /* Do nothing */ 1106 } 1107 1108 static const struct uart_ops sc16is7xx_ops = { 1109 .tx_empty = sc16is7xx_tx_empty, 1110 .set_mctrl = sc16is7xx_set_mctrl, 1111 .get_mctrl = sc16is7xx_get_mctrl, 1112 .stop_tx = sc16is7xx_stop_tx, 1113 .start_tx = sc16is7xx_start_tx, 1114 .stop_rx = sc16is7xx_stop_rx, 1115 .break_ctl = sc16is7xx_break_ctl, 1116 .startup = sc16is7xx_startup, 1117 .shutdown = sc16is7xx_shutdown, 1118 .set_termios = sc16is7xx_set_termios, 1119 .type = sc16is7xx_type, 1120 .request_port = sc16is7xx_request_port, 1121 .release_port = sc16is7xx_null_void, 1122 .config_port = sc16is7xx_config_port, 1123 .verify_port = sc16is7xx_verify_port, 1124 .pm = sc16is7xx_pm, 1125 }; 1126 1127 #ifdef CONFIG_GPIOLIB 1128 static int sc16is7xx_gpio_get(struct gpio_chip *chip, unsigned offset) 1129 { 1130 unsigned int val; 1131 struct sc16is7xx_port *s = gpiochip_get_data(chip); 1132 struct uart_port *port = &s->p[0].port; 1133 1134 val = sc16is7xx_port_read(port, SC16IS7XX_IOSTATE_REG); 1135 1136 return !!(val & BIT(offset)); 1137 } 1138 1139 static void sc16is7xx_gpio_set(struct gpio_chip *chip, unsigned offset, int val) 1140 { 1141 struct sc16is7xx_port *s = gpiochip_get_data(chip); 1142 struct uart_port *port = &s->p[0].port; 1143 1144 sc16is7xx_port_update(port, SC16IS7XX_IOSTATE_REG, BIT(offset), 1145 val ? BIT(offset) : 0); 1146 } 1147 1148 static int sc16is7xx_gpio_direction_input(struct gpio_chip *chip, 1149 unsigned offset) 1150 { 1151 struct sc16is7xx_port *s = gpiochip_get_data(chip); 1152 struct uart_port *port = &s->p[0].port; 1153 1154 sc16is7xx_port_update(port, SC16IS7XX_IODIR_REG, BIT(offset), 0); 1155 1156 return 0; 1157 } 1158 1159 static int sc16is7xx_gpio_direction_output(struct gpio_chip *chip, 1160 unsigned offset, int val) 1161 { 1162 struct sc16is7xx_port *s = gpiochip_get_data(chip); 1163 struct uart_port *port = &s->p[0].port; 1164 u8 state = sc16is7xx_port_read(port, SC16IS7XX_IOSTATE_REG); 1165 1166 if (val) 1167 state |= BIT(offset); 1168 else 1169 state &= ~BIT(offset); 1170 sc16is7xx_port_write(port, SC16IS7XX_IOSTATE_REG, state); 1171 sc16is7xx_port_update(port, SC16IS7XX_IODIR_REG, BIT(offset), 1172 BIT(offset)); 1173 1174 return 0; 1175 } 1176 #endif 1177 1178 static int sc16is7xx_probe(struct device *dev, 1179 const struct sc16is7xx_devtype *devtype, 1180 struct regmap *regmap, int irq) 1181 { 1182 unsigned long freq = 0, *pfreq = dev_get_platdata(dev); 1183 unsigned int val; 1184 u32 uartclk = 0; 1185 int i, ret; 1186 struct sc16is7xx_port *s; 1187 1188 if (IS_ERR(regmap)) 1189 return PTR_ERR(regmap); 1190 1191 /* 1192 * This device does not have an identification register that would 1193 * tell us if we are really connected to the correct device. 1194 * The best we can do is to check if communication is at all possible. 1195 */ 1196 ret = regmap_read(regmap, 1197 SC16IS7XX_LSR_REG << SC16IS7XX_REG_SHIFT, &val); 1198 if (ret < 0) 1199 return -EPROBE_DEFER; 1200 1201 /* Alloc port structure */ 1202 s = devm_kzalloc(dev, struct_size(s, p, devtype->nr_uart), GFP_KERNEL); 1203 if (!s) { 1204 dev_err(dev, "Error allocating port structure\n"); 1205 return -ENOMEM; 1206 } 1207 1208 /* Always ask for fixed clock rate from a property. */ 1209 device_property_read_u32(dev, "clock-frequency", &uartclk); 1210 1211 s->clk = devm_clk_get(dev, NULL); 1212 if (IS_ERR(s->clk)) { 1213 if (uartclk) 1214 freq = uartclk; 1215 if (pfreq) 1216 freq = *pfreq; 1217 if (freq) 1218 dev_dbg(dev, "Clock frequency: %luHz\n", freq); 1219 else 1220 return PTR_ERR(s->clk); 1221 } else { 1222 ret = clk_prepare_enable(s->clk); 1223 if (ret) 1224 return ret; 1225 1226 freq = clk_get_rate(s->clk); 1227 } 1228 1229 s->regmap = regmap; 1230 s->devtype = devtype; 1231 dev_set_drvdata(dev, s); 1232 mutex_init(&s->efr_lock); 1233 1234 kthread_init_worker(&s->kworker); 1235 s->kworker_task = kthread_run(kthread_worker_fn, &s->kworker, 1236 "sc16is7xx"); 1237 if (IS_ERR(s->kworker_task)) { 1238 ret = PTR_ERR(s->kworker_task); 1239 goto out_clk; 1240 } 1241 sched_set_fifo(s->kworker_task); 1242 1243 #ifdef CONFIG_GPIOLIB 1244 if (devtype->nr_gpio) { 1245 /* Setup GPIO cotroller */ 1246 s->gpio.owner = THIS_MODULE; 1247 s->gpio.parent = dev; 1248 s->gpio.label = dev_name(dev); 1249 s->gpio.direction_input = sc16is7xx_gpio_direction_input; 1250 s->gpio.get = sc16is7xx_gpio_get; 1251 s->gpio.direction_output = sc16is7xx_gpio_direction_output; 1252 s->gpio.set = sc16is7xx_gpio_set; 1253 s->gpio.base = -1; 1254 s->gpio.ngpio = devtype->nr_gpio; 1255 s->gpio.can_sleep = 1; 1256 ret = gpiochip_add_data(&s->gpio, s); 1257 if (ret) 1258 goto out_thread; 1259 } 1260 #endif 1261 1262 /* reset device, purging any pending irq / data */ 1263 regmap_write(s->regmap, SC16IS7XX_IOCONTROL_REG << SC16IS7XX_REG_SHIFT, 1264 SC16IS7XX_IOCONTROL_SRESET_BIT); 1265 1266 for (i = 0; i < devtype->nr_uart; ++i) { 1267 s->p[i].line = i; 1268 /* Initialize port data */ 1269 s->p[i].port.dev = dev; 1270 s->p[i].port.irq = irq; 1271 s->p[i].port.type = PORT_SC16IS7XX; 1272 s->p[i].port.fifosize = SC16IS7XX_FIFO_SIZE; 1273 s->p[i].port.flags = UPF_FIXED_TYPE | UPF_LOW_LATENCY; 1274 s->p[i].port.iobase = i; 1275 s->p[i].port.iotype = UPIO_PORT; 1276 s->p[i].port.uartclk = freq; 1277 s->p[i].port.rs485_config = sc16is7xx_config_rs485; 1278 s->p[i].port.ops = &sc16is7xx_ops; 1279 s->p[i].port.line = sc16is7xx_alloc_line(); 1280 if (s->p[i].port.line >= SC16IS7XX_MAX_DEVS) { 1281 ret = -ENOMEM; 1282 goto out_ports; 1283 } 1284 1285 /* Disable all interrupts */ 1286 sc16is7xx_port_write(&s->p[i].port, SC16IS7XX_IER_REG, 0); 1287 /* Disable TX/RX */ 1288 sc16is7xx_port_write(&s->p[i].port, SC16IS7XX_EFCR_REG, 1289 SC16IS7XX_EFCR_RXDISABLE_BIT | 1290 SC16IS7XX_EFCR_TXDISABLE_BIT); 1291 /* Initialize kthread work structs */ 1292 kthread_init_work(&s->p[i].tx_work, sc16is7xx_tx_proc); 1293 kthread_init_work(&s->p[i].reg_work, sc16is7xx_reg_proc); 1294 /* Register port */ 1295 uart_add_one_port(&sc16is7xx_uart, &s->p[i].port); 1296 1297 /* Enable EFR */ 1298 sc16is7xx_port_write(&s->p[i].port, SC16IS7XX_LCR_REG, 1299 SC16IS7XX_LCR_CONF_MODE_B); 1300 1301 regcache_cache_bypass(s->regmap, true); 1302 1303 /* Enable write access to enhanced features */ 1304 sc16is7xx_port_write(&s->p[i].port, SC16IS7XX_EFR_REG, 1305 SC16IS7XX_EFR_ENABLE_BIT); 1306 1307 regcache_cache_bypass(s->regmap, false); 1308 1309 /* Restore access to general registers */ 1310 sc16is7xx_port_write(&s->p[i].port, SC16IS7XX_LCR_REG, 0x00); 1311 1312 /* Go to suspend mode */ 1313 sc16is7xx_power(&s->p[i].port, 0); 1314 } 1315 1316 if (dev->of_node) { 1317 struct property *prop; 1318 const __be32 *p; 1319 u32 u; 1320 1321 of_property_for_each_u32(dev->of_node, "irda-mode-ports", 1322 prop, p, u) 1323 if (u < devtype->nr_uart) 1324 s->p[u].irda_mode = true; 1325 } 1326 1327 /* 1328 * Setup interrupt. We first try to acquire the IRQ line as level IRQ. 1329 * If that succeeds, we can allow sharing the interrupt as well. 1330 * In case the interrupt controller doesn't support that, we fall 1331 * back to a non-shared falling-edge trigger. 1332 */ 1333 ret = devm_request_threaded_irq(dev, irq, NULL, sc16is7xx_irq, 1334 IRQF_TRIGGER_LOW | IRQF_SHARED | 1335 IRQF_ONESHOT, 1336 dev_name(dev), s); 1337 if (!ret) 1338 return 0; 1339 1340 ret = devm_request_threaded_irq(dev, irq, NULL, sc16is7xx_irq, 1341 IRQF_TRIGGER_FALLING | IRQF_ONESHOT, 1342 dev_name(dev), s); 1343 if (!ret) 1344 return 0; 1345 1346 out_ports: 1347 for (i--; i >= 0; i--) { 1348 uart_remove_one_port(&sc16is7xx_uart, &s->p[i].port); 1349 clear_bit(s->p[i].port.line, &sc16is7xx_lines); 1350 } 1351 1352 #ifdef CONFIG_GPIOLIB 1353 if (devtype->nr_gpio) 1354 gpiochip_remove(&s->gpio); 1355 1356 out_thread: 1357 #endif 1358 kthread_stop(s->kworker_task); 1359 1360 out_clk: 1361 if (!IS_ERR(s->clk)) 1362 clk_disable_unprepare(s->clk); 1363 1364 return ret; 1365 } 1366 1367 static int sc16is7xx_remove(struct device *dev) 1368 { 1369 struct sc16is7xx_port *s = dev_get_drvdata(dev); 1370 int i; 1371 1372 #ifdef CONFIG_GPIOLIB 1373 if (s->devtype->nr_gpio) 1374 gpiochip_remove(&s->gpio); 1375 #endif 1376 1377 for (i = 0; i < s->devtype->nr_uart; i++) { 1378 uart_remove_one_port(&sc16is7xx_uart, &s->p[i].port); 1379 clear_bit(s->p[i].port.line, &sc16is7xx_lines); 1380 sc16is7xx_power(&s->p[i].port, 0); 1381 } 1382 1383 kthread_flush_worker(&s->kworker); 1384 kthread_stop(s->kworker_task); 1385 1386 if (!IS_ERR(s->clk)) 1387 clk_disable_unprepare(s->clk); 1388 1389 return 0; 1390 } 1391 1392 static const struct of_device_id __maybe_unused sc16is7xx_dt_ids[] = { 1393 { .compatible = "nxp,sc16is740", .data = &sc16is74x_devtype, }, 1394 { .compatible = "nxp,sc16is741", .data = &sc16is74x_devtype, }, 1395 { .compatible = "nxp,sc16is750", .data = &sc16is750_devtype, }, 1396 { .compatible = "nxp,sc16is752", .data = &sc16is752_devtype, }, 1397 { .compatible = "nxp,sc16is760", .data = &sc16is760_devtype, }, 1398 { .compatible = "nxp,sc16is762", .data = &sc16is762_devtype, }, 1399 { } 1400 }; 1401 MODULE_DEVICE_TABLE(of, sc16is7xx_dt_ids); 1402 1403 static struct regmap_config regcfg = { 1404 .reg_bits = 7, 1405 .pad_bits = 1, 1406 .val_bits = 8, 1407 .cache_type = REGCACHE_RBTREE, 1408 .volatile_reg = sc16is7xx_regmap_volatile, 1409 .precious_reg = sc16is7xx_regmap_precious, 1410 }; 1411 1412 #ifdef CONFIG_SERIAL_SC16IS7XX_SPI 1413 static int sc16is7xx_spi_probe(struct spi_device *spi) 1414 { 1415 const struct sc16is7xx_devtype *devtype; 1416 struct regmap *regmap; 1417 int ret; 1418 1419 /* Setup SPI bus */ 1420 spi->bits_per_word = 8; 1421 /* only supports mode 0 on SC16IS762 */ 1422 spi->mode = spi->mode ? : SPI_MODE_0; 1423 spi->max_speed_hz = spi->max_speed_hz ? : 15000000; 1424 ret = spi_setup(spi); 1425 if (ret) 1426 return ret; 1427 1428 if (spi->dev.of_node) { 1429 devtype = device_get_match_data(&spi->dev); 1430 if (!devtype) 1431 return -ENODEV; 1432 } else { 1433 const struct spi_device_id *id_entry = spi_get_device_id(spi); 1434 1435 devtype = (struct sc16is7xx_devtype *)id_entry->driver_data; 1436 } 1437 1438 regcfg.max_register = (0xf << SC16IS7XX_REG_SHIFT) | 1439 (devtype->nr_uart - 1); 1440 regmap = devm_regmap_init_spi(spi, ®cfg); 1441 1442 return sc16is7xx_probe(&spi->dev, devtype, regmap, spi->irq); 1443 } 1444 1445 static int sc16is7xx_spi_remove(struct spi_device *spi) 1446 { 1447 return sc16is7xx_remove(&spi->dev); 1448 } 1449 1450 static const struct spi_device_id sc16is7xx_spi_id_table[] = { 1451 { "sc16is74x", (kernel_ulong_t)&sc16is74x_devtype, }, 1452 { "sc16is740", (kernel_ulong_t)&sc16is74x_devtype, }, 1453 { "sc16is741", (kernel_ulong_t)&sc16is74x_devtype, }, 1454 { "sc16is750", (kernel_ulong_t)&sc16is750_devtype, }, 1455 { "sc16is752", (kernel_ulong_t)&sc16is752_devtype, }, 1456 { "sc16is760", (kernel_ulong_t)&sc16is760_devtype, }, 1457 { "sc16is762", (kernel_ulong_t)&sc16is762_devtype, }, 1458 { } 1459 }; 1460 1461 MODULE_DEVICE_TABLE(spi, sc16is7xx_spi_id_table); 1462 1463 static struct spi_driver sc16is7xx_spi_uart_driver = { 1464 .driver = { 1465 .name = SC16IS7XX_NAME, 1466 .of_match_table = sc16is7xx_dt_ids, 1467 }, 1468 .probe = sc16is7xx_spi_probe, 1469 .remove = sc16is7xx_spi_remove, 1470 .id_table = sc16is7xx_spi_id_table, 1471 }; 1472 1473 MODULE_ALIAS("spi:sc16is7xx"); 1474 #endif 1475 1476 #ifdef CONFIG_SERIAL_SC16IS7XX_I2C 1477 static int sc16is7xx_i2c_probe(struct i2c_client *i2c, 1478 const struct i2c_device_id *id) 1479 { 1480 const struct sc16is7xx_devtype *devtype; 1481 struct regmap *regmap; 1482 1483 if (i2c->dev.of_node) { 1484 devtype = device_get_match_data(&i2c->dev); 1485 if (!devtype) 1486 return -ENODEV; 1487 } else { 1488 devtype = (struct sc16is7xx_devtype *)id->driver_data; 1489 } 1490 1491 regcfg.max_register = (0xf << SC16IS7XX_REG_SHIFT) | 1492 (devtype->nr_uart - 1); 1493 regmap = devm_regmap_init_i2c(i2c, ®cfg); 1494 1495 return sc16is7xx_probe(&i2c->dev, devtype, regmap, i2c->irq); 1496 } 1497 1498 static int sc16is7xx_i2c_remove(struct i2c_client *client) 1499 { 1500 return sc16is7xx_remove(&client->dev); 1501 } 1502 1503 static const struct i2c_device_id sc16is7xx_i2c_id_table[] = { 1504 { "sc16is74x", (kernel_ulong_t)&sc16is74x_devtype, }, 1505 { "sc16is740", (kernel_ulong_t)&sc16is74x_devtype, }, 1506 { "sc16is741", (kernel_ulong_t)&sc16is74x_devtype, }, 1507 { "sc16is750", (kernel_ulong_t)&sc16is750_devtype, }, 1508 { "sc16is752", (kernel_ulong_t)&sc16is752_devtype, }, 1509 { "sc16is760", (kernel_ulong_t)&sc16is760_devtype, }, 1510 { "sc16is762", (kernel_ulong_t)&sc16is762_devtype, }, 1511 { } 1512 }; 1513 MODULE_DEVICE_TABLE(i2c, sc16is7xx_i2c_id_table); 1514 1515 static struct i2c_driver sc16is7xx_i2c_uart_driver = { 1516 .driver = { 1517 .name = SC16IS7XX_NAME, 1518 .of_match_table = sc16is7xx_dt_ids, 1519 }, 1520 .probe = sc16is7xx_i2c_probe, 1521 .remove = sc16is7xx_i2c_remove, 1522 .id_table = sc16is7xx_i2c_id_table, 1523 }; 1524 1525 #endif 1526 1527 static int __init sc16is7xx_init(void) 1528 { 1529 int ret; 1530 1531 ret = uart_register_driver(&sc16is7xx_uart); 1532 if (ret) { 1533 pr_err("Registering UART driver failed\n"); 1534 return ret; 1535 } 1536 1537 #ifdef CONFIG_SERIAL_SC16IS7XX_I2C 1538 ret = i2c_add_driver(&sc16is7xx_i2c_uart_driver); 1539 if (ret < 0) { 1540 pr_err("failed to init sc16is7xx i2c --> %d\n", ret); 1541 goto err_i2c; 1542 } 1543 #endif 1544 1545 #ifdef CONFIG_SERIAL_SC16IS7XX_SPI 1546 ret = spi_register_driver(&sc16is7xx_spi_uart_driver); 1547 if (ret < 0) { 1548 pr_err("failed to init sc16is7xx spi --> %d\n", ret); 1549 goto err_spi; 1550 } 1551 #endif 1552 return ret; 1553 1554 #ifdef CONFIG_SERIAL_SC16IS7XX_SPI 1555 err_spi: 1556 #endif 1557 #ifdef CONFIG_SERIAL_SC16IS7XX_I2C 1558 i2c_del_driver(&sc16is7xx_i2c_uart_driver); 1559 err_i2c: 1560 #endif 1561 uart_unregister_driver(&sc16is7xx_uart); 1562 return ret; 1563 } 1564 module_init(sc16is7xx_init); 1565 1566 static void __exit sc16is7xx_exit(void) 1567 { 1568 #ifdef CONFIG_SERIAL_SC16IS7XX_I2C 1569 i2c_del_driver(&sc16is7xx_i2c_uart_driver); 1570 #endif 1571 1572 #ifdef CONFIG_SERIAL_SC16IS7XX_SPI 1573 spi_unregister_driver(&sc16is7xx_spi_uart_driver); 1574 #endif 1575 uart_unregister_driver(&sc16is7xx_uart); 1576 } 1577 module_exit(sc16is7xx_exit); 1578 1579 MODULE_LICENSE("GPL"); 1580 MODULE_AUTHOR("Jon Ringle <jringle@gridpoint.com>"); 1581 MODULE_DESCRIPTION("SC16IS7XX serial driver"); 1582