1 /* 2 * Driver for SA11x0 serial ports 3 * 4 * Based on drivers/char/serial.c, by Linus Torvalds, Theodore Ts'o. 5 * 6 * Copyright (C) 2000 Deep Blue Solutions Ltd. 7 * 8 * This program is free software; you can redistribute it and/or modify 9 * it under the terms of the GNU General Public License as published by 10 * the Free Software Foundation; either version 2 of the License, or 11 * (at your option) any later version. 12 * 13 * This program is distributed in the hope that it will be useful, 14 * but WITHOUT ANY WARRANTY; without even the implied warranty of 15 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the 16 * GNU General Public License for more details. 17 * 18 * You should have received a copy of the GNU General Public License 19 * along with this program; if not, write to the Free Software 20 * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA 21 */ 22 23 #if defined(CONFIG_SERIAL_SA1100_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ) 24 #define SUPPORT_SYSRQ 25 #endif 26 27 #include <linux/module.h> 28 #include <linux/ioport.h> 29 #include <linux/init.h> 30 #include <linux/console.h> 31 #include <linux/sysrq.h> 32 #include <linux/platform_data/sa11x0-serial.h> 33 #include <linux/platform_device.h> 34 #include <linux/tty.h> 35 #include <linux/tty_flip.h> 36 #include <linux/serial_core.h> 37 #include <linux/serial.h> 38 #include <linux/io.h> 39 40 #include <asm/irq.h> 41 #include <mach/hardware.h> 42 #include <mach/irqs.h> 43 44 /* We've been assigned a range on the "Low-density serial ports" major */ 45 #define SERIAL_SA1100_MAJOR 204 46 #define MINOR_START 5 47 48 #define NR_PORTS 3 49 50 #define SA1100_ISR_PASS_LIMIT 256 51 52 /* 53 * Convert from ignore_status_mask or read_status_mask to UTSR[01] 54 */ 55 #define SM_TO_UTSR0(x) ((x) & 0xff) 56 #define SM_TO_UTSR1(x) ((x) >> 8) 57 #define UTSR0_TO_SM(x) ((x)) 58 #define UTSR1_TO_SM(x) ((x) << 8) 59 60 #define UART_GET_UTCR0(sport) __raw_readl((sport)->port.membase + UTCR0) 61 #define UART_GET_UTCR1(sport) __raw_readl((sport)->port.membase + UTCR1) 62 #define UART_GET_UTCR2(sport) __raw_readl((sport)->port.membase + UTCR2) 63 #define UART_GET_UTCR3(sport) __raw_readl((sport)->port.membase + UTCR3) 64 #define UART_GET_UTSR0(sport) __raw_readl((sport)->port.membase + UTSR0) 65 #define UART_GET_UTSR1(sport) __raw_readl((sport)->port.membase + UTSR1) 66 #define UART_GET_CHAR(sport) __raw_readl((sport)->port.membase + UTDR) 67 68 #define UART_PUT_UTCR0(sport,v) __raw_writel((v),(sport)->port.membase + UTCR0) 69 #define UART_PUT_UTCR1(sport,v) __raw_writel((v),(sport)->port.membase + UTCR1) 70 #define UART_PUT_UTCR2(sport,v) __raw_writel((v),(sport)->port.membase + UTCR2) 71 #define UART_PUT_UTCR3(sport,v) __raw_writel((v),(sport)->port.membase + UTCR3) 72 #define UART_PUT_UTSR0(sport,v) __raw_writel((v),(sport)->port.membase + UTSR0) 73 #define UART_PUT_UTSR1(sport,v) __raw_writel((v),(sport)->port.membase + UTSR1) 74 #define UART_PUT_CHAR(sport,v) __raw_writel((v),(sport)->port.membase + UTDR) 75 76 /* 77 * This is the size of our serial port register set. 78 */ 79 #define UART_PORT_SIZE 0x24 80 81 /* 82 * This determines how often we check the modem status signals 83 * for any change. They generally aren't connected to an IRQ 84 * so we have to poll them. We also check immediately before 85 * filling the TX fifo incase CTS has been dropped. 86 */ 87 #define MCTRL_TIMEOUT (250*HZ/1000) 88 89 struct sa1100_port { 90 struct uart_port port; 91 struct timer_list timer; 92 unsigned int old_status; 93 }; 94 95 /* 96 * Handle any change of modem status signal since we were last called. 97 */ 98 static void sa1100_mctrl_check(struct sa1100_port *sport) 99 { 100 unsigned int status, changed; 101 102 status = sport->port.ops->get_mctrl(&sport->port); 103 changed = status ^ sport->old_status; 104 105 if (changed == 0) 106 return; 107 108 sport->old_status = status; 109 110 if (changed & TIOCM_RI) 111 sport->port.icount.rng++; 112 if (changed & TIOCM_DSR) 113 sport->port.icount.dsr++; 114 if (changed & TIOCM_CAR) 115 uart_handle_dcd_change(&sport->port, status & TIOCM_CAR); 116 if (changed & TIOCM_CTS) 117 uart_handle_cts_change(&sport->port, status & TIOCM_CTS); 118 119 wake_up_interruptible(&sport->port.state->port.delta_msr_wait); 120 } 121 122 /* 123 * This is our per-port timeout handler, for checking the 124 * modem status signals. 125 */ 126 static void sa1100_timeout(unsigned long data) 127 { 128 struct sa1100_port *sport = (struct sa1100_port *)data; 129 unsigned long flags; 130 131 if (sport->port.state) { 132 spin_lock_irqsave(&sport->port.lock, flags); 133 sa1100_mctrl_check(sport); 134 spin_unlock_irqrestore(&sport->port.lock, flags); 135 136 mod_timer(&sport->timer, jiffies + MCTRL_TIMEOUT); 137 } 138 } 139 140 /* 141 * interrupts disabled on entry 142 */ 143 static void sa1100_stop_tx(struct uart_port *port) 144 { 145 struct sa1100_port *sport = 146 container_of(port, struct sa1100_port, port); 147 u32 utcr3; 148 149 utcr3 = UART_GET_UTCR3(sport); 150 UART_PUT_UTCR3(sport, utcr3 & ~UTCR3_TIE); 151 sport->port.read_status_mask &= ~UTSR0_TO_SM(UTSR0_TFS); 152 } 153 154 /* 155 * port locked and interrupts disabled 156 */ 157 static void sa1100_start_tx(struct uart_port *port) 158 { 159 struct sa1100_port *sport = 160 container_of(port, struct sa1100_port, port); 161 u32 utcr3; 162 163 utcr3 = UART_GET_UTCR3(sport); 164 sport->port.read_status_mask |= UTSR0_TO_SM(UTSR0_TFS); 165 UART_PUT_UTCR3(sport, utcr3 | UTCR3_TIE); 166 } 167 168 /* 169 * Interrupts enabled 170 */ 171 static void sa1100_stop_rx(struct uart_port *port) 172 { 173 struct sa1100_port *sport = 174 container_of(port, struct sa1100_port, port); 175 u32 utcr3; 176 177 utcr3 = UART_GET_UTCR3(sport); 178 UART_PUT_UTCR3(sport, utcr3 & ~UTCR3_RIE); 179 } 180 181 /* 182 * Set the modem control timer to fire immediately. 183 */ 184 static void sa1100_enable_ms(struct uart_port *port) 185 { 186 struct sa1100_port *sport = 187 container_of(port, struct sa1100_port, port); 188 189 mod_timer(&sport->timer, jiffies); 190 } 191 192 static void 193 sa1100_rx_chars(struct sa1100_port *sport) 194 { 195 unsigned int status, ch, flg; 196 197 status = UTSR1_TO_SM(UART_GET_UTSR1(sport)) | 198 UTSR0_TO_SM(UART_GET_UTSR0(sport)); 199 while (status & UTSR1_TO_SM(UTSR1_RNE)) { 200 ch = UART_GET_CHAR(sport); 201 202 sport->port.icount.rx++; 203 204 flg = TTY_NORMAL; 205 206 /* 207 * note that the error handling code is 208 * out of the main execution path 209 */ 210 if (status & UTSR1_TO_SM(UTSR1_PRE | UTSR1_FRE | UTSR1_ROR)) { 211 if (status & UTSR1_TO_SM(UTSR1_PRE)) 212 sport->port.icount.parity++; 213 else if (status & UTSR1_TO_SM(UTSR1_FRE)) 214 sport->port.icount.frame++; 215 if (status & UTSR1_TO_SM(UTSR1_ROR)) 216 sport->port.icount.overrun++; 217 218 status &= sport->port.read_status_mask; 219 220 if (status & UTSR1_TO_SM(UTSR1_PRE)) 221 flg = TTY_PARITY; 222 else if (status & UTSR1_TO_SM(UTSR1_FRE)) 223 flg = TTY_FRAME; 224 225 #ifdef SUPPORT_SYSRQ 226 sport->port.sysrq = 0; 227 #endif 228 } 229 230 if (uart_handle_sysrq_char(&sport->port, ch)) 231 goto ignore_char; 232 233 uart_insert_char(&sport->port, status, UTSR1_TO_SM(UTSR1_ROR), ch, flg); 234 235 ignore_char: 236 status = UTSR1_TO_SM(UART_GET_UTSR1(sport)) | 237 UTSR0_TO_SM(UART_GET_UTSR0(sport)); 238 } 239 240 spin_unlock(&sport->port.lock); 241 tty_flip_buffer_push(&sport->port.state->port); 242 spin_lock(&sport->port.lock); 243 } 244 245 static void sa1100_tx_chars(struct sa1100_port *sport) 246 { 247 struct circ_buf *xmit = &sport->port.state->xmit; 248 249 if (sport->port.x_char) { 250 UART_PUT_CHAR(sport, sport->port.x_char); 251 sport->port.icount.tx++; 252 sport->port.x_char = 0; 253 return; 254 } 255 256 /* 257 * Check the modem control lines before 258 * transmitting anything. 259 */ 260 sa1100_mctrl_check(sport); 261 262 if (uart_circ_empty(xmit) || uart_tx_stopped(&sport->port)) { 263 sa1100_stop_tx(&sport->port); 264 return; 265 } 266 267 /* 268 * Tried using FIFO (not checking TNF) for fifo fill: 269 * still had the '4 bytes repeated' problem. 270 */ 271 while (UART_GET_UTSR1(sport) & UTSR1_TNF) { 272 UART_PUT_CHAR(sport, xmit->buf[xmit->tail]); 273 xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1); 274 sport->port.icount.tx++; 275 if (uart_circ_empty(xmit)) 276 break; 277 } 278 279 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) 280 uart_write_wakeup(&sport->port); 281 282 if (uart_circ_empty(xmit)) 283 sa1100_stop_tx(&sport->port); 284 } 285 286 static irqreturn_t sa1100_int(int irq, void *dev_id) 287 { 288 struct sa1100_port *sport = dev_id; 289 unsigned int status, pass_counter = 0; 290 291 spin_lock(&sport->port.lock); 292 status = UART_GET_UTSR0(sport); 293 status &= SM_TO_UTSR0(sport->port.read_status_mask) | ~UTSR0_TFS; 294 do { 295 if (status & (UTSR0_RFS | UTSR0_RID)) { 296 /* Clear the receiver idle bit, if set */ 297 if (status & UTSR0_RID) 298 UART_PUT_UTSR0(sport, UTSR0_RID); 299 sa1100_rx_chars(sport); 300 } 301 302 /* Clear the relevant break bits */ 303 if (status & (UTSR0_RBB | UTSR0_REB)) 304 UART_PUT_UTSR0(sport, status & (UTSR0_RBB | UTSR0_REB)); 305 306 if (status & UTSR0_RBB) 307 sport->port.icount.brk++; 308 309 if (status & UTSR0_REB) 310 uart_handle_break(&sport->port); 311 312 if (status & UTSR0_TFS) 313 sa1100_tx_chars(sport); 314 if (pass_counter++ > SA1100_ISR_PASS_LIMIT) 315 break; 316 status = UART_GET_UTSR0(sport); 317 status &= SM_TO_UTSR0(sport->port.read_status_mask) | 318 ~UTSR0_TFS; 319 } while (status & (UTSR0_TFS | UTSR0_RFS | UTSR0_RID)); 320 spin_unlock(&sport->port.lock); 321 322 return IRQ_HANDLED; 323 } 324 325 /* 326 * Return TIOCSER_TEMT when transmitter is not busy. 327 */ 328 static unsigned int sa1100_tx_empty(struct uart_port *port) 329 { 330 struct sa1100_port *sport = 331 container_of(port, struct sa1100_port, port); 332 333 return UART_GET_UTSR1(sport) & UTSR1_TBY ? 0 : TIOCSER_TEMT; 334 } 335 336 static unsigned int sa1100_get_mctrl(struct uart_port *port) 337 { 338 return TIOCM_CTS | TIOCM_DSR | TIOCM_CAR; 339 } 340 341 static void sa1100_set_mctrl(struct uart_port *port, unsigned int mctrl) 342 { 343 } 344 345 /* 346 * Interrupts always disabled. 347 */ 348 static void sa1100_break_ctl(struct uart_port *port, int break_state) 349 { 350 struct sa1100_port *sport = 351 container_of(port, struct sa1100_port, port); 352 unsigned long flags; 353 unsigned int utcr3; 354 355 spin_lock_irqsave(&sport->port.lock, flags); 356 utcr3 = UART_GET_UTCR3(sport); 357 if (break_state == -1) 358 utcr3 |= UTCR3_BRK; 359 else 360 utcr3 &= ~UTCR3_BRK; 361 UART_PUT_UTCR3(sport, utcr3); 362 spin_unlock_irqrestore(&sport->port.lock, flags); 363 } 364 365 static int sa1100_startup(struct uart_port *port) 366 { 367 struct sa1100_port *sport = 368 container_of(port, struct sa1100_port, port); 369 int retval; 370 371 /* 372 * Allocate the IRQ 373 */ 374 retval = request_irq(sport->port.irq, sa1100_int, 0, 375 "sa11x0-uart", sport); 376 if (retval) 377 return retval; 378 379 /* 380 * Finally, clear and enable interrupts 381 */ 382 UART_PUT_UTSR0(sport, -1); 383 UART_PUT_UTCR3(sport, UTCR3_RXE | UTCR3_TXE | UTCR3_RIE); 384 385 /* 386 * Enable modem status interrupts 387 */ 388 spin_lock_irq(&sport->port.lock); 389 sa1100_enable_ms(&sport->port); 390 spin_unlock_irq(&sport->port.lock); 391 392 return 0; 393 } 394 395 static void sa1100_shutdown(struct uart_port *port) 396 { 397 struct sa1100_port *sport = 398 container_of(port, struct sa1100_port, port); 399 400 /* 401 * Stop our timer. 402 */ 403 del_timer_sync(&sport->timer); 404 405 /* 406 * Free the interrupt 407 */ 408 free_irq(sport->port.irq, sport); 409 410 /* 411 * Disable all interrupts, port and break condition. 412 */ 413 UART_PUT_UTCR3(sport, 0); 414 } 415 416 static void 417 sa1100_set_termios(struct uart_port *port, struct ktermios *termios, 418 struct ktermios *old) 419 { 420 struct sa1100_port *sport = 421 container_of(port, struct sa1100_port, port); 422 unsigned long flags; 423 unsigned int utcr0, old_utcr3, baud, quot; 424 unsigned int old_csize = old ? old->c_cflag & CSIZE : CS8; 425 426 /* 427 * We only support CS7 and CS8. 428 */ 429 while ((termios->c_cflag & CSIZE) != CS7 && 430 (termios->c_cflag & CSIZE) != CS8) { 431 termios->c_cflag &= ~CSIZE; 432 termios->c_cflag |= old_csize; 433 old_csize = CS8; 434 } 435 436 if ((termios->c_cflag & CSIZE) == CS8) 437 utcr0 = UTCR0_DSS; 438 else 439 utcr0 = 0; 440 441 if (termios->c_cflag & CSTOPB) 442 utcr0 |= UTCR0_SBS; 443 if (termios->c_cflag & PARENB) { 444 utcr0 |= UTCR0_PE; 445 if (!(termios->c_cflag & PARODD)) 446 utcr0 |= UTCR0_OES; 447 } 448 449 /* 450 * Ask the core to calculate the divisor for us. 451 */ 452 baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16); 453 quot = uart_get_divisor(port, baud); 454 455 spin_lock_irqsave(&sport->port.lock, flags); 456 457 sport->port.read_status_mask &= UTSR0_TO_SM(UTSR0_TFS); 458 sport->port.read_status_mask |= UTSR1_TO_SM(UTSR1_ROR); 459 if (termios->c_iflag & INPCK) 460 sport->port.read_status_mask |= 461 UTSR1_TO_SM(UTSR1_FRE | UTSR1_PRE); 462 if (termios->c_iflag & (BRKINT | PARMRK)) 463 sport->port.read_status_mask |= 464 UTSR0_TO_SM(UTSR0_RBB | UTSR0_REB); 465 466 /* 467 * Characters to ignore 468 */ 469 sport->port.ignore_status_mask = 0; 470 if (termios->c_iflag & IGNPAR) 471 sport->port.ignore_status_mask |= 472 UTSR1_TO_SM(UTSR1_FRE | UTSR1_PRE); 473 if (termios->c_iflag & IGNBRK) { 474 sport->port.ignore_status_mask |= 475 UTSR0_TO_SM(UTSR0_RBB | UTSR0_REB); 476 /* 477 * If we're ignoring parity and break indicators, 478 * ignore overruns too (for real raw support). 479 */ 480 if (termios->c_iflag & IGNPAR) 481 sport->port.ignore_status_mask |= 482 UTSR1_TO_SM(UTSR1_ROR); 483 } 484 485 del_timer_sync(&sport->timer); 486 487 /* 488 * Update the per-port timeout. 489 */ 490 uart_update_timeout(port, termios->c_cflag, baud); 491 492 /* 493 * disable interrupts and drain transmitter 494 */ 495 old_utcr3 = UART_GET_UTCR3(sport); 496 UART_PUT_UTCR3(sport, old_utcr3 & ~(UTCR3_RIE | UTCR3_TIE)); 497 498 while (UART_GET_UTSR1(sport) & UTSR1_TBY) 499 barrier(); 500 501 /* then, disable everything */ 502 UART_PUT_UTCR3(sport, 0); 503 504 /* set the parity, stop bits and data size */ 505 UART_PUT_UTCR0(sport, utcr0); 506 507 /* set the baud rate */ 508 quot -= 1; 509 UART_PUT_UTCR1(sport, ((quot & 0xf00) >> 8)); 510 UART_PUT_UTCR2(sport, (quot & 0xff)); 511 512 UART_PUT_UTSR0(sport, -1); 513 514 UART_PUT_UTCR3(sport, old_utcr3); 515 516 if (UART_ENABLE_MS(&sport->port, termios->c_cflag)) 517 sa1100_enable_ms(&sport->port); 518 519 spin_unlock_irqrestore(&sport->port.lock, flags); 520 } 521 522 static const char *sa1100_type(struct uart_port *port) 523 { 524 struct sa1100_port *sport = 525 container_of(port, struct sa1100_port, port); 526 527 return sport->port.type == PORT_SA1100 ? "SA1100" : NULL; 528 } 529 530 /* 531 * Release the memory region(s) being used by 'port'. 532 */ 533 static void sa1100_release_port(struct uart_port *port) 534 { 535 struct sa1100_port *sport = 536 container_of(port, struct sa1100_port, port); 537 538 release_mem_region(sport->port.mapbase, UART_PORT_SIZE); 539 } 540 541 /* 542 * Request the memory region(s) being used by 'port'. 543 */ 544 static int sa1100_request_port(struct uart_port *port) 545 { 546 struct sa1100_port *sport = 547 container_of(port, struct sa1100_port, port); 548 549 return request_mem_region(sport->port.mapbase, UART_PORT_SIZE, 550 "sa11x0-uart") != NULL ? 0 : -EBUSY; 551 } 552 553 /* 554 * Configure/autoconfigure the port. 555 */ 556 static void sa1100_config_port(struct uart_port *port, int flags) 557 { 558 struct sa1100_port *sport = 559 container_of(port, struct sa1100_port, port); 560 561 if (flags & UART_CONFIG_TYPE && 562 sa1100_request_port(&sport->port) == 0) 563 sport->port.type = PORT_SA1100; 564 } 565 566 /* 567 * Verify the new serial_struct (for TIOCSSERIAL). 568 * The only change we allow are to the flags and type, and 569 * even then only between PORT_SA1100 and PORT_UNKNOWN 570 */ 571 static int 572 sa1100_verify_port(struct uart_port *port, struct serial_struct *ser) 573 { 574 struct sa1100_port *sport = 575 container_of(port, struct sa1100_port, port); 576 int ret = 0; 577 578 if (ser->type != PORT_UNKNOWN && ser->type != PORT_SA1100) 579 ret = -EINVAL; 580 if (sport->port.irq != ser->irq) 581 ret = -EINVAL; 582 if (ser->io_type != SERIAL_IO_MEM) 583 ret = -EINVAL; 584 if (sport->port.uartclk / 16 != ser->baud_base) 585 ret = -EINVAL; 586 if ((void *)sport->port.mapbase != ser->iomem_base) 587 ret = -EINVAL; 588 if (sport->port.iobase != ser->port) 589 ret = -EINVAL; 590 if (ser->hub6 != 0) 591 ret = -EINVAL; 592 return ret; 593 } 594 595 static struct uart_ops sa1100_pops = { 596 .tx_empty = sa1100_tx_empty, 597 .set_mctrl = sa1100_set_mctrl, 598 .get_mctrl = sa1100_get_mctrl, 599 .stop_tx = sa1100_stop_tx, 600 .start_tx = sa1100_start_tx, 601 .stop_rx = sa1100_stop_rx, 602 .enable_ms = sa1100_enable_ms, 603 .break_ctl = sa1100_break_ctl, 604 .startup = sa1100_startup, 605 .shutdown = sa1100_shutdown, 606 .set_termios = sa1100_set_termios, 607 .type = sa1100_type, 608 .release_port = sa1100_release_port, 609 .request_port = sa1100_request_port, 610 .config_port = sa1100_config_port, 611 .verify_port = sa1100_verify_port, 612 }; 613 614 static struct sa1100_port sa1100_ports[NR_PORTS]; 615 616 /* 617 * Setup the SA1100 serial ports. Note that we don't include the IrDA 618 * port here since we have our own SIR/FIR driver (see drivers/net/irda) 619 * 620 * Note also that we support "console=ttySAx" where "x" is either 0 or 1. 621 * Which serial port this ends up being depends on the machine you're 622 * running this kernel on. I'm not convinced that this is a good idea, 623 * but that's the way it traditionally works. 624 * 625 * Note that NanoEngine UART3 becomes UART2, and UART2 is no longer 626 * used here. 627 */ 628 static void __init sa1100_init_ports(void) 629 { 630 static int first = 1; 631 int i; 632 633 if (!first) 634 return; 635 first = 0; 636 637 for (i = 0; i < NR_PORTS; i++) { 638 sa1100_ports[i].port.uartclk = 3686400; 639 sa1100_ports[i].port.ops = &sa1100_pops; 640 sa1100_ports[i].port.fifosize = 8; 641 sa1100_ports[i].port.line = i; 642 sa1100_ports[i].port.iotype = UPIO_MEM; 643 init_timer(&sa1100_ports[i].timer); 644 sa1100_ports[i].timer.function = sa1100_timeout; 645 sa1100_ports[i].timer.data = (unsigned long)&sa1100_ports[i]; 646 } 647 648 /* 649 * make transmit lines outputs, so that when the port 650 * is closed, the output is in the MARK state. 651 */ 652 PPDR |= PPC_TXD1 | PPC_TXD3; 653 PPSR |= PPC_TXD1 | PPC_TXD3; 654 } 655 656 void sa1100_register_uart_fns(struct sa1100_port_fns *fns) 657 { 658 if (fns->get_mctrl) 659 sa1100_pops.get_mctrl = fns->get_mctrl; 660 if (fns->set_mctrl) 661 sa1100_pops.set_mctrl = fns->set_mctrl; 662 663 sa1100_pops.pm = fns->pm; 664 /* 665 * FIXME: fns->set_wake is unused - this should be called from 666 * the suspend() callback if device_may_wakeup(dev)) is set. 667 */ 668 } 669 670 void __init sa1100_register_uart(int idx, int port) 671 { 672 if (idx >= NR_PORTS) { 673 printk(KERN_ERR "%s: bad index number %d\n", __func__, idx); 674 return; 675 } 676 677 switch (port) { 678 case 1: 679 sa1100_ports[idx].port.membase = (void __iomem *)&Ser1UTCR0; 680 sa1100_ports[idx].port.mapbase = _Ser1UTCR0; 681 sa1100_ports[idx].port.irq = IRQ_Ser1UART; 682 sa1100_ports[idx].port.flags = UPF_BOOT_AUTOCONF; 683 break; 684 685 case 2: 686 sa1100_ports[idx].port.membase = (void __iomem *)&Ser2UTCR0; 687 sa1100_ports[idx].port.mapbase = _Ser2UTCR0; 688 sa1100_ports[idx].port.irq = IRQ_Ser2ICP; 689 sa1100_ports[idx].port.flags = UPF_BOOT_AUTOCONF; 690 break; 691 692 case 3: 693 sa1100_ports[idx].port.membase = (void __iomem *)&Ser3UTCR0; 694 sa1100_ports[idx].port.mapbase = _Ser3UTCR0; 695 sa1100_ports[idx].port.irq = IRQ_Ser3UART; 696 sa1100_ports[idx].port.flags = UPF_BOOT_AUTOCONF; 697 break; 698 699 default: 700 printk(KERN_ERR "%s: bad port number %d\n", __func__, port); 701 } 702 } 703 704 705 #ifdef CONFIG_SERIAL_SA1100_CONSOLE 706 static void sa1100_console_putchar(struct uart_port *port, int ch) 707 { 708 struct sa1100_port *sport = 709 container_of(port, struct sa1100_port, port); 710 711 while (!(UART_GET_UTSR1(sport) & UTSR1_TNF)) 712 barrier(); 713 UART_PUT_CHAR(sport, ch); 714 } 715 716 /* 717 * Interrupts are disabled on entering 718 */ 719 static void 720 sa1100_console_write(struct console *co, const char *s, unsigned int count) 721 { 722 struct sa1100_port *sport = &sa1100_ports[co->index]; 723 unsigned int old_utcr3, status; 724 725 /* 726 * First, save UTCR3 and then disable interrupts 727 */ 728 old_utcr3 = UART_GET_UTCR3(sport); 729 UART_PUT_UTCR3(sport, (old_utcr3 & ~(UTCR3_RIE | UTCR3_TIE)) | 730 UTCR3_TXE); 731 732 uart_console_write(&sport->port, s, count, sa1100_console_putchar); 733 734 /* 735 * Finally, wait for transmitter to become empty 736 * and restore UTCR3 737 */ 738 do { 739 status = UART_GET_UTSR1(sport); 740 } while (status & UTSR1_TBY); 741 UART_PUT_UTCR3(sport, old_utcr3); 742 } 743 744 /* 745 * If the port was already initialised (eg, by a boot loader), 746 * try to determine the current setup. 747 */ 748 static void __init 749 sa1100_console_get_options(struct sa1100_port *sport, int *baud, 750 int *parity, int *bits) 751 { 752 unsigned int utcr3; 753 754 utcr3 = UART_GET_UTCR3(sport) & (UTCR3_RXE | UTCR3_TXE); 755 if (utcr3 == (UTCR3_RXE | UTCR3_TXE)) { 756 /* ok, the port was enabled */ 757 unsigned int utcr0, quot; 758 759 utcr0 = UART_GET_UTCR0(sport); 760 761 *parity = 'n'; 762 if (utcr0 & UTCR0_PE) { 763 if (utcr0 & UTCR0_OES) 764 *parity = 'e'; 765 else 766 *parity = 'o'; 767 } 768 769 if (utcr0 & UTCR0_DSS) 770 *bits = 8; 771 else 772 *bits = 7; 773 774 quot = UART_GET_UTCR2(sport) | UART_GET_UTCR1(sport) << 8; 775 quot &= 0xfff; 776 *baud = sport->port.uartclk / (16 * (quot + 1)); 777 } 778 } 779 780 static int __init 781 sa1100_console_setup(struct console *co, char *options) 782 { 783 struct sa1100_port *sport; 784 int baud = 9600; 785 int bits = 8; 786 int parity = 'n'; 787 int flow = 'n'; 788 789 /* 790 * Check whether an invalid uart number has been specified, and 791 * if so, search for the first available port that does have 792 * console support. 793 */ 794 if (co->index == -1 || co->index >= NR_PORTS) 795 co->index = 0; 796 sport = &sa1100_ports[co->index]; 797 798 if (options) 799 uart_parse_options(options, &baud, &parity, &bits, &flow); 800 else 801 sa1100_console_get_options(sport, &baud, &parity, &bits); 802 803 return uart_set_options(&sport->port, co, baud, parity, bits, flow); 804 } 805 806 static struct uart_driver sa1100_reg; 807 static struct console sa1100_console = { 808 .name = "ttySA", 809 .write = sa1100_console_write, 810 .device = uart_console_device, 811 .setup = sa1100_console_setup, 812 .flags = CON_PRINTBUFFER, 813 .index = -1, 814 .data = &sa1100_reg, 815 }; 816 817 static int __init sa1100_rs_console_init(void) 818 { 819 sa1100_init_ports(); 820 register_console(&sa1100_console); 821 return 0; 822 } 823 console_initcall(sa1100_rs_console_init); 824 825 #define SA1100_CONSOLE &sa1100_console 826 #else 827 #define SA1100_CONSOLE NULL 828 #endif 829 830 static struct uart_driver sa1100_reg = { 831 .owner = THIS_MODULE, 832 .driver_name = "ttySA", 833 .dev_name = "ttySA", 834 .major = SERIAL_SA1100_MAJOR, 835 .minor = MINOR_START, 836 .nr = NR_PORTS, 837 .cons = SA1100_CONSOLE, 838 }; 839 840 static int sa1100_serial_suspend(struct platform_device *dev, pm_message_t state) 841 { 842 struct sa1100_port *sport = platform_get_drvdata(dev); 843 844 if (sport) 845 uart_suspend_port(&sa1100_reg, &sport->port); 846 847 return 0; 848 } 849 850 static int sa1100_serial_resume(struct platform_device *dev) 851 { 852 struct sa1100_port *sport = platform_get_drvdata(dev); 853 854 if (sport) 855 uart_resume_port(&sa1100_reg, &sport->port); 856 857 return 0; 858 } 859 860 static int sa1100_serial_probe(struct platform_device *dev) 861 { 862 struct resource *res = dev->resource; 863 int i; 864 865 for (i = 0; i < dev->num_resources; i++, res++) 866 if (res->flags & IORESOURCE_MEM) 867 break; 868 869 if (i < dev->num_resources) { 870 for (i = 0; i < NR_PORTS; i++) { 871 if (sa1100_ports[i].port.mapbase != res->start) 872 continue; 873 874 sa1100_ports[i].port.dev = &dev->dev; 875 uart_add_one_port(&sa1100_reg, &sa1100_ports[i].port); 876 platform_set_drvdata(dev, &sa1100_ports[i]); 877 break; 878 } 879 } 880 881 return 0; 882 } 883 884 static int sa1100_serial_remove(struct platform_device *pdev) 885 { 886 struct sa1100_port *sport = platform_get_drvdata(pdev); 887 888 if (sport) 889 uart_remove_one_port(&sa1100_reg, &sport->port); 890 891 return 0; 892 } 893 894 static struct platform_driver sa11x0_serial_driver = { 895 .probe = sa1100_serial_probe, 896 .remove = sa1100_serial_remove, 897 .suspend = sa1100_serial_suspend, 898 .resume = sa1100_serial_resume, 899 .driver = { 900 .name = "sa11x0-uart", 901 }, 902 }; 903 904 static int __init sa1100_serial_init(void) 905 { 906 int ret; 907 908 printk(KERN_INFO "Serial: SA11x0 driver\n"); 909 910 sa1100_init_ports(); 911 912 ret = uart_register_driver(&sa1100_reg); 913 if (ret == 0) { 914 ret = platform_driver_register(&sa11x0_serial_driver); 915 if (ret) 916 uart_unregister_driver(&sa1100_reg); 917 } 918 return ret; 919 } 920 921 static void __exit sa1100_serial_exit(void) 922 { 923 platform_driver_unregister(&sa11x0_serial_driver); 924 uart_unregister_driver(&sa1100_reg); 925 } 926 927 module_init(sa1100_serial_init); 928 module_exit(sa1100_serial_exit); 929 930 MODULE_AUTHOR("Deep Blue Solutions Ltd"); 931 MODULE_DESCRIPTION("SA1100 generic serial port driver"); 932 MODULE_LICENSE("GPL"); 933 MODULE_ALIAS_CHARDEV_MAJOR(SERIAL_SA1100_MAJOR); 934 MODULE_ALIAS("platform:sa11x0-uart"); 935