1 // SPDX-License-Identifier: GPL-2.0+ 2 /* 3 * Driver for SA11x0 serial ports 4 * 5 * Based on drivers/char/serial.c, by Linus Torvalds, Theodore Ts'o. 6 * 7 * Copyright (C) 2000 Deep Blue Solutions Ltd. 8 */ 9 10 #include <linux/module.h> 11 #include <linux/ioport.h> 12 #include <linux/init.h> 13 #include <linux/console.h> 14 #include <linux/sysrq.h> 15 #include <linux/platform_data/sa11x0-serial.h> 16 #include <linux/platform_device.h> 17 #include <linux/tty.h> 18 #include <linux/tty_flip.h> 19 #include <linux/serial_core.h> 20 #include <linux/serial.h> 21 #include <linux/io.h> 22 23 #include <asm/irq.h> 24 #include <mach/hardware.h> 25 #include <mach/irqs.h> 26 27 #include "serial_mctrl_gpio.h" 28 29 /* We've been assigned a range on the "Low-density serial ports" major */ 30 #define SERIAL_SA1100_MAJOR 204 31 #define MINOR_START 5 32 33 #define NR_PORTS 3 34 35 #define SA1100_ISR_PASS_LIMIT 256 36 37 /* 38 * Convert from ignore_status_mask or read_status_mask to UTSR[01] 39 */ 40 #define SM_TO_UTSR0(x) ((x) & 0xff) 41 #define SM_TO_UTSR1(x) ((x) >> 8) 42 #define UTSR0_TO_SM(x) ((x)) 43 #define UTSR1_TO_SM(x) ((x) << 8) 44 45 #define UART_GET_UTCR0(sport) __raw_readl((sport)->port.membase + UTCR0) 46 #define UART_GET_UTCR1(sport) __raw_readl((sport)->port.membase + UTCR1) 47 #define UART_GET_UTCR2(sport) __raw_readl((sport)->port.membase + UTCR2) 48 #define UART_GET_UTCR3(sport) __raw_readl((sport)->port.membase + UTCR3) 49 #define UART_GET_UTSR0(sport) __raw_readl((sport)->port.membase + UTSR0) 50 #define UART_GET_UTSR1(sport) __raw_readl((sport)->port.membase + UTSR1) 51 #define UART_GET_CHAR(sport) __raw_readl((sport)->port.membase + UTDR) 52 53 #define UART_PUT_UTCR0(sport,v) __raw_writel((v),(sport)->port.membase + UTCR0) 54 #define UART_PUT_UTCR1(sport,v) __raw_writel((v),(sport)->port.membase + UTCR1) 55 #define UART_PUT_UTCR2(sport,v) __raw_writel((v),(sport)->port.membase + UTCR2) 56 #define UART_PUT_UTCR3(sport,v) __raw_writel((v),(sport)->port.membase + UTCR3) 57 #define UART_PUT_UTSR0(sport,v) __raw_writel((v),(sport)->port.membase + UTSR0) 58 #define UART_PUT_UTSR1(sport,v) __raw_writel((v),(sport)->port.membase + UTSR1) 59 #define UART_PUT_CHAR(sport,v) __raw_writel((v),(sport)->port.membase + UTDR) 60 61 /* 62 * This is the size of our serial port register set. 63 */ 64 #define UART_PORT_SIZE 0x24 65 66 /* 67 * This determines how often we check the modem status signals 68 * for any change. They generally aren't connected to an IRQ 69 * so we have to poll them. We also check immediately before 70 * filling the TX fifo incase CTS has been dropped. 71 */ 72 #define MCTRL_TIMEOUT (250*HZ/1000) 73 74 struct sa1100_port { 75 struct uart_port port; 76 struct timer_list timer; 77 unsigned int old_status; 78 struct mctrl_gpios *gpios; 79 }; 80 81 /* 82 * Handle any change of modem status signal since we were last called. 83 */ 84 static void sa1100_mctrl_check(struct sa1100_port *sport) 85 { 86 unsigned int status, changed; 87 88 status = sport->port.ops->get_mctrl(&sport->port); 89 changed = status ^ sport->old_status; 90 91 if (changed == 0) 92 return; 93 94 sport->old_status = status; 95 96 if (changed & TIOCM_RI) 97 sport->port.icount.rng++; 98 if (changed & TIOCM_DSR) 99 sport->port.icount.dsr++; 100 if (changed & TIOCM_CAR) 101 uart_handle_dcd_change(&sport->port, status & TIOCM_CAR); 102 if (changed & TIOCM_CTS) 103 uart_handle_cts_change(&sport->port, status & TIOCM_CTS); 104 105 wake_up_interruptible(&sport->port.state->port.delta_msr_wait); 106 } 107 108 /* 109 * This is our per-port timeout handler, for checking the 110 * modem status signals. 111 */ 112 static void sa1100_timeout(struct timer_list *t) 113 { 114 struct sa1100_port *sport = from_timer(sport, t, timer); 115 unsigned long flags; 116 117 if (sport->port.state) { 118 spin_lock_irqsave(&sport->port.lock, flags); 119 sa1100_mctrl_check(sport); 120 spin_unlock_irqrestore(&sport->port.lock, flags); 121 122 mod_timer(&sport->timer, jiffies + MCTRL_TIMEOUT); 123 } 124 } 125 126 /* 127 * interrupts disabled on entry 128 */ 129 static void sa1100_stop_tx(struct uart_port *port) 130 { 131 struct sa1100_port *sport = 132 container_of(port, struct sa1100_port, port); 133 u32 utcr3; 134 135 utcr3 = UART_GET_UTCR3(sport); 136 UART_PUT_UTCR3(sport, utcr3 & ~UTCR3_TIE); 137 sport->port.read_status_mask &= ~UTSR0_TO_SM(UTSR0_TFS); 138 } 139 140 /* 141 * port locked and interrupts disabled 142 */ 143 static void sa1100_start_tx(struct uart_port *port) 144 { 145 struct sa1100_port *sport = 146 container_of(port, struct sa1100_port, port); 147 u32 utcr3; 148 149 utcr3 = UART_GET_UTCR3(sport); 150 sport->port.read_status_mask |= UTSR0_TO_SM(UTSR0_TFS); 151 UART_PUT_UTCR3(sport, utcr3 | UTCR3_TIE); 152 } 153 154 /* 155 * Interrupts enabled 156 */ 157 static void sa1100_stop_rx(struct uart_port *port) 158 { 159 struct sa1100_port *sport = 160 container_of(port, struct sa1100_port, port); 161 u32 utcr3; 162 163 utcr3 = UART_GET_UTCR3(sport); 164 UART_PUT_UTCR3(sport, utcr3 & ~UTCR3_RIE); 165 } 166 167 /* 168 * Set the modem control timer to fire immediately. 169 */ 170 static void sa1100_enable_ms(struct uart_port *port) 171 { 172 struct sa1100_port *sport = 173 container_of(port, struct sa1100_port, port); 174 175 mod_timer(&sport->timer, jiffies); 176 177 mctrl_gpio_enable_ms(sport->gpios); 178 } 179 180 static void 181 sa1100_rx_chars(struct sa1100_port *sport) 182 { 183 unsigned int status, ch, flg; 184 185 status = UTSR1_TO_SM(UART_GET_UTSR1(sport)) | 186 UTSR0_TO_SM(UART_GET_UTSR0(sport)); 187 while (status & UTSR1_TO_SM(UTSR1_RNE)) { 188 ch = UART_GET_CHAR(sport); 189 190 sport->port.icount.rx++; 191 192 flg = TTY_NORMAL; 193 194 /* 195 * note that the error handling code is 196 * out of the main execution path 197 */ 198 if (status & UTSR1_TO_SM(UTSR1_PRE | UTSR1_FRE | UTSR1_ROR)) { 199 if (status & UTSR1_TO_SM(UTSR1_PRE)) 200 sport->port.icount.parity++; 201 else if (status & UTSR1_TO_SM(UTSR1_FRE)) 202 sport->port.icount.frame++; 203 if (status & UTSR1_TO_SM(UTSR1_ROR)) 204 sport->port.icount.overrun++; 205 206 status &= sport->port.read_status_mask; 207 208 if (status & UTSR1_TO_SM(UTSR1_PRE)) 209 flg = TTY_PARITY; 210 else if (status & UTSR1_TO_SM(UTSR1_FRE)) 211 flg = TTY_FRAME; 212 213 sport->port.sysrq = 0; 214 } 215 216 if (uart_handle_sysrq_char(&sport->port, ch)) 217 goto ignore_char; 218 219 uart_insert_char(&sport->port, status, UTSR1_TO_SM(UTSR1_ROR), ch, flg); 220 221 ignore_char: 222 status = UTSR1_TO_SM(UART_GET_UTSR1(sport)) | 223 UTSR0_TO_SM(UART_GET_UTSR0(sport)); 224 } 225 226 spin_unlock(&sport->port.lock); 227 tty_flip_buffer_push(&sport->port.state->port); 228 spin_lock(&sport->port.lock); 229 } 230 231 static void sa1100_tx_chars(struct sa1100_port *sport) 232 { 233 struct circ_buf *xmit = &sport->port.state->xmit; 234 235 if (sport->port.x_char) { 236 UART_PUT_CHAR(sport, sport->port.x_char); 237 sport->port.icount.tx++; 238 sport->port.x_char = 0; 239 return; 240 } 241 242 /* 243 * Check the modem control lines before 244 * transmitting anything. 245 */ 246 sa1100_mctrl_check(sport); 247 248 if (uart_circ_empty(xmit) || uart_tx_stopped(&sport->port)) { 249 sa1100_stop_tx(&sport->port); 250 return; 251 } 252 253 /* 254 * Tried using FIFO (not checking TNF) for fifo fill: 255 * still had the '4 bytes repeated' problem. 256 */ 257 while (UART_GET_UTSR1(sport) & UTSR1_TNF) { 258 UART_PUT_CHAR(sport, xmit->buf[xmit->tail]); 259 xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1); 260 sport->port.icount.tx++; 261 if (uart_circ_empty(xmit)) 262 break; 263 } 264 265 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) 266 uart_write_wakeup(&sport->port); 267 268 if (uart_circ_empty(xmit)) 269 sa1100_stop_tx(&sport->port); 270 } 271 272 static irqreturn_t sa1100_int(int irq, void *dev_id) 273 { 274 struct sa1100_port *sport = dev_id; 275 unsigned int status, pass_counter = 0; 276 277 spin_lock(&sport->port.lock); 278 status = UART_GET_UTSR0(sport); 279 status &= SM_TO_UTSR0(sport->port.read_status_mask) | ~UTSR0_TFS; 280 do { 281 if (status & (UTSR0_RFS | UTSR0_RID)) { 282 /* Clear the receiver idle bit, if set */ 283 if (status & UTSR0_RID) 284 UART_PUT_UTSR0(sport, UTSR0_RID); 285 sa1100_rx_chars(sport); 286 } 287 288 /* Clear the relevant break bits */ 289 if (status & (UTSR0_RBB | UTSR0_REB)) 290 UART_PUT_UTSR0(sport, status & (UTSR0_RBB | UTSR0_REB)); 291 292 if (status & UTSR0_RBB) 293 sport->port.icount.brk++; 294 295 if (status & UTSR0_REB) 296 uart_handle_break(&sport->port); 297 298 if (status & UTSR0_TFS) 299 sa1100_tx_chars(sport); 300 if (pass_counter++ > SA1100_ISR_PASS_LIMIT) 301 break; 302 status = UART_GET_UTSR0(sport); 303 status &= SM_TO_UTSR0(sport->port.read_status_mask) | 304 ~UTSR0_TFS; 305 } while (status & (UTSR0_TFS | UTSR0_RFS | UTSR0_RID)); 306 spin_unlock(&sport->port.lock); 307 308 return IRQ_HANDLED; 309 } 310 311 /* 312 * Return TIOCSER_TEMT when transmitter is not busy. 313 */ 314 static unsigned int sa1100_tx_empty(struct uart_port *port) 315 { 316 struct sa1100_port *sport = 317 container_of(port, struct sa1100_port, port); 318 319 return UART_GET_UTSR1(sport) & UTSR1_TBY ? 0 : TIOCSER_TEMT; 320 } 321 322 static unsigned int sa1100_get_mctrl(struct uart_port *port) 323 { 324 struct sa1100_port *sport = 325 container_of(port, struct sa1100_port, port); 326 int ret = TIOCM_CTS | TIOCM_DSR | TIOCM_CAR; 327 328 mctrl_gpio_get(sport->gpios, &ret); 329 330 return ret; 331 } 332 333 static void sa1100_set_mctrl(struct uart_port *port, unsigned int mctrl) 334 { 335 struct sa1100_port *sport = 336 container_of(port, struct sa1100_port, port); 337 338 mctrl_gpio_set(sport->gpios, mctrl); 339 } 340 341 /* 342 * Interrupts always disabled. 343 */ 344 static void sa1100_break_ctl(struct uart_port *port, int break_state) 345 { 346 struct sa1100_port *sport = 347 container_of(port, struct sa1100_port, port); 348 unsigned long flags; 349 unsigned int utcr3; 350 351 spin_lock_irqsave(&sport->port.lock, flags); 352 utcr3 = UART_GET_UTCR3(sport); 353 if (break_state == -1) 354 utcr3 |= UTCR3_BRK; 355 else 356 utcr3 &= ~UTCR3_BRK; 357 UART_PUT_UTCR3(sport, utcr3); 358 spin_unlock_irqrestore(&sport->port.lock, flags); 359 } 360 361 static int sa1100_startup(struct uart_port *port) 362 { 363 struct sa1100_port *sport = 364 container_of(port, struct sa1100_port, port); 365 int retval; 366 367 /* 368 * Allocate the IRQ 369 */ 370 retval = request_irq(sport->port.irq, sa1100_int, 0, 371 "sa11x0-uart", sport); 372 if (retval) 373 return retval; 374 375 /* 376 * Finally, clear and enable interrupts 377 */ 378 UART_PUT_UTSR0(sport, -1); 379 UART_PUT_UTCR3(sport, UTCR3_RXE | UTCR3_TXE | UTCR3_RIE); 380 381 /* 382 * Enable modem status interrupts 383 */ 384 spin_lock_irq(&sport->port.lock); 385 sa1100_enable_ms(&sport->port); 386 spin_unlock_irq(&sport->port.lock); 387 388 return 0; 389 } 390 391 static void sa1100_shutdown(struct uart_port *port) 392 { 393 struct sa1100_port *sport = 394 container_of(port, struct sa1100_port, port); 395 396 /* 397 * Stop our timer. 398 */ 399 del_timer_sync(&sport->timer); 400 401 /* 402 * Free the interrupt 403 */ 404 free_irq(sport->port.irq, sport); 405 406 /* 407 * Disable all interrupts, port and break condition. 408 */ 409 UART_PUT_UTCR3(sport, 0); 410 } 411 412 static void 413 sa1100_set_termios(struct uart_port *port, struct ktermios *termios, 414 struct ktermios *old) 415 { 416 struct sa1100_port *sport = 417 container_of(port, struct sa1100_port, port); 418 unsigned long flags; 419 unsigned int utcr0, old_utcr3, baud, quot; 420 unsigned int old_csize = old ? old->c_cflag & CSIZE : CS8; 421 422 /* 423 * We only support CS7 and CS8. 424 */ 425 while ((termios->c_cflag & CSIZE) != CS7 && 426 (termios->c_cflag & CSIZE) != CS8) { 427 termios->c_cflag &= ~CSIZE; 428 termios->c_cflag |= old_csize; 429 old_csize = CS8; 430 } 431 432 if ((termios->c_cflag & CSIZE) == CS8) 433 utcr0 = UTCR0_DSS; 434 else 435 utcr0 = 0; 436 437 if (termios->c_cflag & CSTOPB) 438 utcr0 |= UTCR0_SBS; 439 if (termios->c_cflag & PARENB) { 440 utcr0 |= UTCR0_PE; 441 if (!(termios->c_cflag & PARODD)) 442 utcr0 |= UTCR0_OES; 443 } 444 445 /* 446 * Ask the core to calculate the divisor for us. 447 */ 448 baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16); 449 quot = uart_get_divisor(port, baud); 450 451 spin_lock_irqsave(&sport->port.lock, flags); 452 453 sport->port.read_status_mask &= UTSR0_TO_SM(UTSR0_TFS); 454 sport->port.read_status_mask |= UTSR1_TO_SM(UTSR1_ROR); 455 if (termios->c_iflag & INPCK) 456 sport->port.read_status_mask |= 457 UTSR1_TO_SM(UTSR1_FRE | UTSR1_PRE); 458 if (termios->c_iflag & (BRKINT | PARMRK)) 459 sport->port.read_status_mask |= 460 UTSR0_TO_SM(UTSR0_RBB | UTSR0_REB); 461 462 /* 463 * Characters to ignore 464 */ 465 sport->port.ignore_status_mask = 0; 466 if (termios->c_iflag & IGNPAR) 467 sport->port.ignore_status_mask |= 468 UTSR1_TO_SM(UTSR1_FRE | UTSR1_PRE); 469 if (termios->c_iflag & IGNBRK) { 470 sport->port.ignore_status_mask |= 471 UTSR0_TO_SM(UTSR0_RBB | UTSR0_REB); 472 /* 473 * If we're ignoring parity and break indicators, 474 * ignore overruns too (for real raw support). 475 */ 476 if (termios->c_iflag & IGNPAR) 477 sport->port.ignore_status_mask |= 478 UTSR1_TO_SM(UTSR1_ROR); 479 } 480 481 del_timer_sync(&sport->timer); 482 483 /* 484 * Update the per-port timeout. 485 */ 486 uart_update_timeout(port, termios->c_cflag, baud); 487 488 /* 489 * disable interrupts and drain transmitter 490 */ 491 old_utcr3 = UART_GET_UTCR3(sport); 492 UART_PUT_UTCR3(sport, old_utcr3 & ~(UTCR3_RIE | UTCR3_TIE)); 493 494 while (UART_GET_UTSR1(sport) & UTSR1_TBY) 495 barrier(); 496 497 /* then, disable everything */ 498 UART_PUT_UTCR3(sport, 0); 499 500 /* set the parity, stop bits and data size */ 501 UART_PUT_UTCR0(sport, utcr0); 502 503 /* set the baud rate */ 504 quot -= 1; 505 UART_PUT_UTCR1(sport, ((quot & 0xf00) >> 8)); 506 UART_PUT_UTCR2(sport, (quot & 0xff)); 507 508 UART_PUT_UTSR0(sport, -1); 509 510 UART_PUT_UTCR3(sport, old_utcr3); 511 512 if (UART_ENABLE_MS(&sport->port, termios->c_cflag)) 513 sa1100_enable_ms(&sport->port); 514 515 spin_unlock_irqrestore(&sport->port.lock, flags); 516 } 517 518 static const char *sa1100_type(struct uart_port *port) 519 { 520 struct sa1100_port *sport = 521 container_of(port, struct sa1100_port, port); 522 523 return sport->port.type == PORT_SA1100 ? "SA1100" : NULL; 524 } 525 526 /* 527 * Release the memory region(s) being used by 'port'. 528 */ 529 static void sa1100_release_port(struct uart_port *port) 530 { 531 struct sa1100_port *sport = 532 container_of(port, struct sa1100_port, port); 533 534 release_mem_region(sport->port.mapbase, UART_PORT_SIZE); 535 } 536 537 /* 538 * Request the memory region(s) being used by 'port'. 539 */ 540 static int sa1100_request_port(struct uart_port *port) 541 { 542 struct sa1100_port *sport = 543 container_of(port, struct sa1100_port, port); 544 545 return request_mem_region(sport->port.mapbase, UART_PORT_SIZE, 546 "sa11x0-uart") != NULL ? 0 : -EBUSY; 547 } 548 549 /* 550 * Configure/autoconfigure the port. 551 */ 552 static void sa1100_config_port(struct uart_port *port, int flags) 553 { 554 struct sa1100_port *sport = 555 container_of(port, struct sa1100_port, port); 556 557 if (flags & UART_CONFIG_TYPE && 558 sa1100_request_port(&sport->port) == 0) 559 sport->port.type = PORT_SA1100; 560 } 561 562 /* 563 * Verify the new serial_struct (for TIOCSSERIAL). 564 * The only change we allow are to the flags and type, and 565 * even then only between PORT_SA1100 and PORT_UNKNOWN 566 */ 567 static int 568 sa1100_verify_port(struct uart_port *port, struct serial_struct *ser) 569 { 570 struct sa1100_port *sport = 571 container_of(port, struct sa1100_port, port); 572 int ret = 0; 573 574 if (ser->type != PORT_UNKNOWN && ser->type != PORT_SA1100) 575 ret = -EINVAL; 576 if (sport->port.irq != ser->irq) 577 ret = -EINVAL; 578 if (ser->io_type != SERIAL_IO_MEM) 579 ret = -EINVAL; 580 if (sport->port.uartclk / 16 != ser->baud_base) 581 ret = -EINVAL; 582 if ((void *)sport->port.mapbase != ser->iomem_base) 583 ret = -EINVAL; 584 if (sport->port.iobase != ser->port) 585 ret = -EINVAL; 586 if (ser->hub6 != 0) 587 ret = -EINVAL; 588 return ret; 589 } 590 591 static struct uart_ops sa1100_pops = { 592 .tx_empty = sa1100_tx_empty, 593 .set_mctrl = sa1100_set_mctrl, 594 .get_mctrl = sa1100_get_mctrl, 595 .stop_tx = sa1100_stop_tx, 596 .start_tx = sa1100_start_tx, 597 .stop_rx = sa1100_stop_rx, 598 .enable_ms = sa1100_enable_ms, 599 .break_ctl = sa1100_break_ctl, 600 .startup = sa1100_startup, 601 .shutdown = sa1100_shutdown, 602 .set_termios = sa1100_set_termios, 603 .type = sa1100_type, 604 .release_port = sa1100_release_port, 605 .request_port = sa1100_request_port, 606 .config_port = sa1100_config_port, 607 .verify_port = sa1100_verify_port, 608 }; 609 610 static struct sa1100_port sa1100_ports[NR_PORTS]; 611 612 /* 613 * Setup the SA1100 serial ports. Note that we don't include the IrDA 614 * port here since we have our own SIR/FIR driver (see drivers/net/irda) 615 * 616 * Note also that we support "console=ttySAx" where "x" is either 0 or 1. 617 * Which serial port this ends up being depends on the machine you're 618 * running this kernel on. I'm not convinced that this is a good idea, 619 * but that's the way it traditionally works. 620 * 621 * Note that NanoEngine UART3 becomes UART2, and UART2 is no longer 622 * used here. 623 */ 624 static void __init sa1100_init_ports(void) 625 { 626 static int first = 1; 627 int i; 628 629 if (!first) 630 return; 631 first = 0; 632 633 for (i = 0; i < NR_PORTS; i++) { 634 sa1100_ports[i].port.uartclk = 3686400; 635 sa1100_ports[i].port.ops = &sa1100_pops; 636 sa1100_ports[i].port.fifosize = 8; 637 sa1100_ports[i].port.line = i; 638 sa1100_ports[i].port.iotype = UPIO_MEM; 639 timer_setup(&sa1100_ports[i].timer, sa1100_timeout, 0); 640 } 641 642 /* 643 * make transmit lines outputs, so that when the port 644 * is closed, the output is in the MARK state. 645 */ 646 PPDR |= PPC_TXD1 | PPC_TXD3; 647 PPSR |= PPC_TXD1 | PPC_TXD3; 648 } 649 650 void sa1100_register_uart_fns(struct sa1100_port_fns *fns) 651 { 652 if (fns->get_mctrl) 653 sa1100_pops.get_mctrl = fns->get_mctrl; 654 if (fns->set_mctrl) 655 sa1100_pops.set_mctrl = fns->set_mctrl; 656 657 sa1100_pops.pm = fns->pm; 658 /* 659 * FIXME: fns->set_wake is unused - this should be called from 660 * the suspend() callback if device_may_wakeup(dev)) is set. 661 */ 662 } 663 664 void __init sa1100_register_uart(int idx, int port) 665 { 666 if (idx >= NR_PORTS) { 667 printk(KERN_ERR "%s: bad index number %d\n", __func__, idx); 668 return; 669 } 670 671 switch (port) { 672 case 1: 673 sa1100_ports[idx].port.membase = (void __iomem *)&Ser1UTCR0; 674 sa1100_ports[idx].port.mapbase = _Ser1UTCR0; 675 sa1100_ports[idx].port.irq = IRQ_Ser1UART; 676 sa1100_ports[idx].port.flags = UPF_BOOT_AUTOCONF; 677 break; 678 679 case 2: 680 sa1100_ports[idx].port.membase = (void __iomem *)&Ser2UTCR0; 681 sa1100_ports[idx].port.mapbase = _Ser2UTCR0; 682 sa1100_ports[idx].port.irq = IRQ_Ser2ICP; 683 sa1100_ports[idx].port.flags = UPF_BOOT_AUTOCONF; 684 break; 685 686 case 3: 687 sa1100_ports[idx].port.membase = (void __iomem *)&Ser3UTCR0; 688 sa1100_ports[idx].port.mapbase = _Ser3UTCR0; 689 sa1100_ports[idx].port.irq = IRQ_Ser3UART; 690 sa1100_ports[idx].port.flags = UPF_BOOT_AUTOCONF; 691 break; 692 693 default: 694 printk(KERN_ERR "%s: bad port number %d\n", __func__, port); 695 } 696 } 697 698 699 #ifdef CONFIG_SERIAL_SA1100_CONSOLE 700 static void sa1100_console_putchar(struct uart_port *port, int ch) 701 { 702 struct sa1100_port *sport = 703 container_of(port, struct sa1100_port, port); 704 705 while (!(UART_GET_UTSR1(sport) & UTSR1_TNF)) 706 barrier(); 707 UART_PUT_CHAR(sport, ch); 708 } 709 710 /* 711 * Interrupts are disabled on entering 712 */ 713 static void 714 sa1100_console_write(struct console *co, const char *s, unsigned int count) 715 { 716 struct sa1100_port *sport = &sa1100_ports[co->index]; 717 unsigned int old_utcr3, status; 718 719 /* 720 * First, save UTCR3 and then disable interrupts 721 */ 722 old_utcr3 = UART_GET_UTCR3(sport); 723 UART_PUT_UTCR3(sport, (old_utcr3 & ~(UTCR3_RIE | UTCR3_TIE)) | 724 UTCR3_TXE); 725 726 uart_console_write(&sport->port, s, count, sa1100_console_putchar); 727 728 /* 729 * Finally, wait for transmitter to become empty 730 * and restore UTCR3 731 */ 732 do { 733 status = UART_GET_UTSR1(sport); 734 } while (status & UTSR1_TBY); 735 UART_PUT_UTCR3(sport, old_utcr3); 736 } 737 738 /* 739 * If the port was already initialised (eg, by a boot loader), 740 * try to determine the current setup. 741 */ 742 static void __init 743 sa1100_console_get_options(struct sa1100_port *sport, int *baud, 744 int *parity, int *bits) 745 { 746 unsigned int utcr3; 747 748 utcr3 = UART_GET_UTCR3(sport) & (UTCR3_RXE | UTCR3_TXE); 749 if (utcr3 == (UTCR3_RXE | UTCR3_TXE)) { 750 /* ok, the port was enabled */ 751 unsigned int utcr0, quot; 752 753 utcr0 = UART_GET_UTCR0(sport); 754 755 *parity = 'n'; 756 if (utcr0 & UTCR0_PE) { 757 if (utcr0 & UTCR0_OES) 758 *parity = 'e'; 759 else 760 *parity = 'o'; 761 } 762 763 if (utcr0 & UTCR0_DSS) 764 *bits = 8; 765 else 766 *bits = 7; 767 768 quot = UART_GET_UTCR2(sport) | UART_GET_UTCR1(sport) << 8; 769 quot &= 0xfff; 770 *baud = sport->port.uartclk / (16 * (quot + 1)); 771 } 772 } 773 774 static int __init 775 sa1100_console_setup(struct console *co, char *options) 776 { 777 struct sa1100_port *sport; 778 int baud = 9600; 779 int bits = 8; 780 int parity = 'n'; 781 int flow = 'n'; 782 783 /* 784 * Check whether an invalid uart number has been specified, and 785 * if so, search for the first available port that does have 786 * console support. 787 */ 788 if (co->index == -1 || co->index >= NR_PORTS) 789 co->index = 0; 790 sport = &sa1100_ports[co->index]; 791 792 if (options) 793 uart_parse_options(options, &baud, &parity, &bits, &flow); 794 else 795 sa1100_console_get_options(sport, &baud, &parity, &bits); 796 797 return uart_set_options(&sport->port, co, baud, parity, bits, flow); 798 } 799 800 static struct uart_driver sa1100_reg; 801 static struct console sa1100_console = { 802 .name = "ttySA", 803 .write = sa1100_console_write, 804 .device = uart_console_device, 805 .setup = sa1100_console_setup, 806 .flags = CON_PRINTBUFFER, 807 .index = -1, 808 .data = &sa1100_reg, 809 }; 810 811 static int __init sa1100_rs_console_init(void) 812 { 813 sa1100_init_ports(); 814 register_console(&sa1100_console); 815 return 0; 816 } 817 console_initcall(sa1100_rs_console_init); 818 819 #define SA1100_CONSOLE &sa1100_console 820 #else 821 #define SA1100_CONSOLE NULL 822 #endif 823 824 static struct uart_driver sa1100_reg = { 825 .owner = THIS_MODULE, 826 .driver_name = "ttySA", 827 .dev_name = "ttySA", 828 .major = SERIAL_SA1100_MAJOR, 829 .minor = MINOR_START, 830 .nr = NR_PORTS, 831 .cons = SA1100_CONSOLE, 832 }; 833 834 static int sa1100_serial_suspend(struct platform_device *dev, pm_message_t state) 835 { 836 struct sa1100_port *sport = platform_get_drvdata(dev); 837 838 if (sport) 839 uart_suspend_port(&sa1100_reg, &sport->port); 840 841 return 0; 842 } 843 844 static int sa1100_serial_resume(struct platform_device *dev) 845 { 846 struct sa1100_port *sport = platform_get_drvdata(dev); 847 848 if (sport) 849 uart_resume_port(&sa1100_reg, &sport->port); 850 851 return 0; 852 } 853 854 static int sa1100_serial_add_one_port(struct sa1100_port *sport, struct platform_device *dev) 855 { 856 sport->port.dev = &dev->dev; 857 sport->port.has_sysrq = IS_ENABLED(CONFIG_SERIAL_SA1100_CONSOLE); 858 859 // mctrl_gpio_init() requires that the GPIO driver supports interrupts, 860 // but we need to support GPIO drivers for hardware that has no such 861 // interrupts. Use mctrl_gpio_init_noauto() instead. 862 sport->gpios = mctrl_gpio_init_noauto(sport->port.dev, 0); 863 if (IS_ERR(sport->gpios)) { 864 int err = PTR_ERR(sport->gpios); 865 866 dev_err(sport->port.dev, "failed to get mctrl gpios: %d\n", 867 err); 868 869 if (err == -EPROBE_DEFER) 870 return err; 871 872 sport->gpios = NULL; 873 } 874 875 platform_set_drvdata(dev, sport); 876 877 return uart_add_one_port(&sa1100_reg, &sport->port); 878 } 879 880 static int sa1100_serial_probe(struct platform_device *dev) 881 { 882 struct resource *res; 883 int i; 884 885 res = platform_get_resource(dev, IORESOURCE_MEM, 0); 886 if (!res) 887 return -EINVAL; 888 889 for (i = 0; i < NR_PORTS; i++) 890 if (sa1100_ports[i].port.mapbase == res->start) 891 break; 892 if (i == NR_PORTS) 893 return -ENODEV; 894 895 sa1100_serial_add_one_port(&sa1100_ports[i], dev); 896 897 return 0; 898 } 899 900 static int sa1100_serial_remove(struct platform_device *pdev) 901 { 902 struct sa1100_port *sport = platform_get_drvdata(pdev); 903 904 if (sport) 905 uart_remove_one_port(&sa1100_reg, &sport->port); 906 907 return 0; 908 } 909 910 static struct platform_driver sa11x0_serial_driver = { 911 .probe = sa1100_serial_probe, 912 .remove = sa1100_serial_remove, 913 .suspend = sa1100_serial_suspend, 914 .resume = sa1100_serial_resume, 915 .driver = { 916 .name = "sa11x0-uart", 917 }, 918 }; 919 920 static int __init sa1100_serial_init(void) 921 { 922 int ret; 923 924 printk(KERN_INFO "Serial: SA11x0 driver\n"); 925 926 sa1100_init_ports(); 927 928 ret = uart_register_driver(&sa1100_reg); 929 if (ret == 0) { 930 ret = platform_driver_register(&sa11x0_serial_driver); 931 if (ret) 932 uart_unregister_driver(&sa1100_reg); 933 } 934 return ret; 935 } 936 937 static void __exit sa1100_serial_exit(void) 938 { 939 platform_driver_unregister(&sa11x0_serial_driver); 940 uart_unregister_driver(&sa1100_reg); 941 } 942 943 module_init(sa1100_serial_init); 944 module_exit(sa1100_serial_exit); 945 946 MODULE_AUTHOR("Deep Blue Solutions Ltd"); 947 MODULE_DESCRIPTION("SA1100 generic serial port driver"); 948 MODULE_LICENSE("GPL"); 949 MODULE_ALIAS_CHARDEV_MAJOR(SERIAL_SA1100_MAJOR); 950 MODULE_ALIAS("platform:sa11x0-uart"); 951