1 // SPDX-License-Identifier: GPL-2.0 2 // Copyright (c) 2017-2018, The Linux foundation. All rights reserved. 3 4 #include <linux/clk.h> 5 #include <linux/console.h> 6 #include <linux/io.h> 7 #include <linux/iopoll.h> 8 #include <linux/irq.h> 9 #include <linux/module.h> 10 #include <linux/of.h> 11 #include <linux/of_device.h> 12 #include <linux/pm_opp.h> 13 #include <linux/platform_device.h> 14 #include <linux/pm_runtime.h> 15 #include <linux/pm_wakeirq.h> 16 #include <linux/qcom-geni-se.h> 17 #include <linux/serial.h> 18 #include <linux/serial_core.h> 19 #include <linux/slab.h> 20 #include <linux/tty.h> 21 #include <linux/tty_flip.h> 22 23 /* UART specific GENI registers */ 24 #define SE_UART_LOOPBACK_CFG 0x22c 25 #define SE_UART_IO_MACRO_CTRL 0x240 26 #define SE_UART_TX_TRANS_CFG 0x25c 27 #define SE_UART_TX_WORD_LEN 0x268 28 #define SE_UART_TX_STOP_BIT_LEN 0x26c 29 #define SE_UART_TX_TRANS_LEN 0x270 30 #define SE_UART_RX_TRANS_CFG 0x280 31 #define SE_UART_RX_WORD_LEN 0x28c 32 #define SE_UART_RX_STALE_CNT 0x294 33 #define SE_UART_TX_PARITY_CFG 0x2a4 34 #define SE_UART_RX_PARITY_CFG 0x2a8 35 #define SE_UART_MANUAL_RFR 0x2ac 36 37 /* SE_UART_TRANS_CFG */ 38 #define UART_TX_PAR_EN BIT(0) 39 #define UART_CTS_MASK BIT(1) 40 41 /* SE_UART_TX_WORD_LEN */ 42 #define TX_WORD_LEN_MSK GENMASK(9, 0) 43 44 /* SE_UART_TX_STOP_BIT_LEN */ 45 #define TX_STOP_BIT_LEN_MSK GENMASK(23, 0) 46 #define TX_STOP_BIT_LEN_1 0 47 #define TX_STOP_BIT_LEN_1_5 1 48 #define TX_STOP_BIT_LEN_2 2 49 50 /* SE_UART_TX_TRANS_LEN */ 51 #define TX_TRANS_LEN_MSK GENMASK(23, 0) 52 53 /* SE_UART_RX_TRANS_CFG */ 54 #define UART_RX_INS_STATUS_BIT BIT(2) 55 #define UART_RX_PAR_EN BIT(3) 56 57 /* SE_UART_RX_WORD_LEN */ 58 #define RX_WORD_LEN_MASK GENMASK(9, 0) 59 60 /* SE_UART_RX_STALE_CNT */ 61 #define RX_STALE_CNT GENMASK(23, 0) 62 63 /* SE_UART_TX_PARITY_CFG/RX_PARITY_CFG */ 64 #define PAR_CALC_EN BIT(0) 65 #define PAR_MODE_MSK GENMASK(2, 1) 66 #define PAR_MODE_SHFT 1 67 #define PAR_EVEN 0x00 68 #define PAR_ODD 0x01 69 #define PAR_SPACE 0x10 70 #define PAR_MARK 0x11 71 72 /* SE_UART_MANUAL_RFR register fields */ 73 #define UART_MANUAL_RFR_EN BIT(31) 74 #define UART_RFR_NOT_READY BIT(1) 75 #define UART_RFR_READY BIT(0) 76 77 /* UART M_CMD OP codes */ 78 #define UART_START_TX 0x1 79 #define UART_START_BREAK 0x4 80 #define UART_STOP_BREAK 0x5 81 /* UART S_CMD OP codes */ 82 #define UART_START_READ 0x1 83 #define UART_PARAM 0x1 84 85 #define UART_OVERSAMPLING 32 86 #define STALE_TIMEOUT 16 87 #define DEFAULT_BITS_PER_CHAR 10 88 #define GENI_UART_CONS_PORTS 1 89 #define GENI_UART_PORTS 3 90 #define DEF_FIFO_DEPTH_WORDS 16 91 #define DEF_TX_WM 2 92 #define DEF_FIFO_WIDTH_BITS 32 93 #define UART_RX_WM 2 94 95 /* SE_UART_LOOPBACK_CFG */ 96 #define RX_TX_SORTED BIT(0) 97 #define CTS_RTS_SORTED BIT(1) 98 #define RX_TX_CTS_RTS_SORTED (RX_TX_SORTED | CTS_RTS_SORTED) 99 100 /* UART pin swap value */ 101 #define DEFAULT_IO_MACRO_IO0_IO1_MASK GENMASK(3, 0) 102 #define IO_MACRO_IO0_SEL 0x3 103 #define DEFAULT_IO_MACRO_IO2_IO3_MASK GENMASK(15, 4) 104 #define IO_MACRO_IO2_IO3_SWAP 0x4640 105 106 /* We always configure 4 bytes per FIFO word */ 107 #define BYTES_PER_FIFO_WORD 4 108 109 struct qcom_geni_private_data { 110 /* NOTE: earlycon port will have NULL here */ 111 struct uart_driver *drv; 112 113 u32 poll_cached_bytes; 114 unsigned int poll_cached_bytes_cnt; 115 116 u32 write_cached_bytes; 117 unsigned int write_cached_bytes_cnt; 118 }; 119 120 struct qcom_geni_serial_port { 121 struct uart_port uport; 122 struct geni_se se; 123 const char *name; 124 u32 tx_fifo_depth; 125 u32 tx_fifo_width; 126 u32 rx_fifo_depth; 127 bool setup; 128 int (*handle_rx)(struct uart_port *uport, u32 bytes, bool drop); 129 unsigned int baud; 130 void *rx_fifo; 131 u32 loopback; 132 bool brk; 133 134 unsigned int tx_remaining; 135 int wakeup_irq; 136 bool rx_tx_swap; 137 bool cts_rts_swap; 138 139 struct qcom_geni_private_data private_data; 140 }; 141 142 static const struct uart_ops qcom_geni_console_pops; 143 static const struct uart_ops qcom_geni_uart_pops; 144 static struct uart_driver qcom_geni_console_driver; 145 static struct uart_driver qcom_geni_uart_driver; 146 static int handle_rx_console(struct uart_port *uport, u32 bytes, bool drop); 147 static int handle_rx_uart(struct uart_port *uport, u32 bytes, bool drop); 148 static unsigned int qcom_geni_serial_tx_empty(struct uart_port *port); 149 static void qcom_geni_serial_stop_rx(struct uart_port *uport); 150 static void qcom_geni_serial_handle_rx(struct uart_port *uport, bool drop); 151 152 static const unsigned long root_freq[] = {7372800, 14745600, 19200000, 29491200, 153 32000000, 48000000, 51200000, 64000000, 154 80000000, 96000000, 100000000, 155 102400000, 112000000, 120000000, 156 128000000}; 157 158 #define to_dev_port(ptr, member) \ 159 container_of(ptr, struct qcom_geni_serial_port, member) 160 161 static struct qcom_geni_serial_port qcom_geni_uart_ports[GENI_UART_PORTS] = { 162 [0] = { 163 .uport = { 164 .iotype = UPIO_MEM, 165 .ops = &qcom_geni_uart_pops, 166 .flags = UPF_BOOT_AUTOCONF, 167 .line = 0, 168 }, 169 }, 170 [1] = { 171 .uport = { 172 .iotype = UPIO_MEM, 173 .ops = &qcom_geni_uart_pops, 174 .flags = UPF_BOOT_AUTOCONF, 175 .line = 1, 176 }, 177 }, 178 [2] = { 179 .uport = { 180 .iotype = UPIO_MEM, 181 .ops = &qcom_geni_uart_pops, 182 .flags = UPF_BOOT_AUTOCONF, 183 .line = 2, 184 }, 185 }, 186 }; 187 188 static struct qcom_geni_serial_port qcom_geni_console_port = { 189 .uport = { 190 .iotype = UPIO_MEM, 191 .ops = &qcom_geni_console_pops, 192 .flags = UPF_BOOT_AUTOCONF, 193 .line = 0, 194 }, 195 }; 196 197 static int qcom_geni_serial_request_port(struct uart_port *uport) 198 { 199 struct platform_device *pdev = to_platform_device(uport->dev); 200 struct qcom_geni_serial_port *port = to_dev_port(uport, uport); 201 202 uport->membase = devm_platform_ioremap_resource(pdev, 0); 203 if (IS_ERR(uport->membase)) 204 return PTR_ERR(uport->membase); 205 port->se.base = uport->membase; 206 return 0; 207 } 208 209 static void qcom_geni_serial_config_port(struct uart_port *uport, int cfg_flags) 210 { 211 if (cfg_flags & UART_CONFIG_TYPE) { 212 uport->type = PORT_MSM; 213 qcom_geni_serial_request_port(uport); 214 } 215 } 216 217 static unsigned int qcom_geni_serial_get_mctrl(struct uart_port *uport) 218 { 219 unsigned int mctrl = TIOCM_DSR | TIOCM_CAR; 220 u32 geni_ios; 221 222 if (uart_console(uport)) { 223 mctrl |= TIOCM_CTS; 224 } else { 225 geni_ios = readl(uport->membase + SE_GENI_IOS); 226 if (!(geni_ios & IO2_DATA_IN)) 227 mctrl |= TIOCM_CTS; 228 } 229 230 return mctrl; 231 } 232 233 static void qcom_geni_serial_set_mctrl(struct uart_port *uport, 234 unsigned int mctrl) 235 { 236 u32 uart_manual_rfr = 0; 237 struct qcom_geni_serial_port *port = to_dev_port(uport, uport); 238 239 if (uart_console(uport)) 240 return; 241 242 if (mctrl & TIOCM_LOOP) 243 port->loopback = RX_TX_CTS_RTS_SORTED; 244 245 if (!(mctrl & TIOCM_RTS) && !uport->suspended) 246 uart_manual_rfr = UART_MANUAL_RFR_EN | UART_RFR_NOT_READY; 247 writel(uart_manual_rfr, uport->membase + SE_UART_MANUAL_RFR); 248 } 249 250 static const char *qcom_geni_serial_get_type(struct uart_port *uport) 251 { 252 return "MSM"; 253 } 254 255 static struct qcom_geni_serial_port *get_port_from_line(int line, bool console) 256 { 257 struct qcom_geni_serial_port *port; 258 int nr_ports = console ? GENI_UART_CONS_PORTS : GENI_UART_PORTS; 259 260 if (line < 0 || line >= nr_ports) 261 return ERR_PTR(-ENXIO); 262 263 port = console ? &qcom_geni_console_port : &qcom_geni_uart_ports[line]; 264 return port; 265 } 266 267 static bool qcom_geni_serial_poll_bit(struct uart_port *uport, 268 int offset, int field, bool set) 269 { 270 u32 reg; 271 struct qcom_geni_serial_port *port; 272 unsigned int baud; 273 unsigned int fifo_bits; 274 unsigned long timeout_us = 20000; 275 struct qcom_geni_private_data *private_data = uport->private_data; 276 277 if (private_data->drv) { 278 port = to_dev_port(uport, uport); 279 baud = port->baud; 280 if (!baud) 281 baud = 115200; 282 fifo_bits = port->tx_fifo_depth * port->tx_fifo_width; 283 /* 284 * Total polling iterations based on FIFO worth of bytes to be 285 * sent at current baud. Add a little fluff to the wait. 286 */ 287 timeout_us = ((fifo_bits * USEC_PER_SEC) / baud) + 500; 288 } 289 290 /* 291 * Use custom implementation instead of readl_poll_atomic since ktimer 292 * is not ready at the time of early console. 293 */ 294 timeout_us = DIV_ROUND_UP(timeout_us, 10) * 10; 295 while (timeout_us) { 296 reg = readl(uport->membase + offset); 297 if ((bool)(reg & field) == set) 298 return true; 299 udelay(10); 300 timeout_us -= 10; 301 } 302 return false; 303 } 304 305 static void qcom_geni_serial_setup_tx(struct uart_port *uport, u32 xmit_size) 306 { 307 u32 m_cmd; 308 309 writel(xmit_size, uport->membase + SE_UART_TX_TRANS_LEN); 310 m_cmd = UART_START_TX << M_OPCODE_SHFT; 311 writel(m_cmd, uport->membase + SE_GENI_M_CMD0); 312 } 313 314 static void qcom_geni_serial_poll_tx_done(struct uart_port *uport) 315 { 316 int done; 317 u32 irq_clear = M_CMD_DONE_EN; 318 319 done = qcom_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS, 320 M_CMD_DONE_EN, true); 321 if (!done) { 322 writel(M_GENI_CMD_ABORT, uport->membase + 323 SE_GENI_M_CMD_CTRL_REG); 324 irq_clear |= M_CMD_ABORT_EN; 325 qcom_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS, 326 M_CMD_ABORT_EN, true); 327 } 328 writel(irq_clear, uport->membase + SE_GENI_M_IRQ_CLEAR); 329 } 330 331 static void qcom_geni_serial_abort_rx(struct uart_port *uport) 332 { 333 u32 irq_clear = S_CMD_DONE_EN | S_CMD_ABORT_EN; 334 335 writel(S_GENI_CMD_ABORT, uport->membase + SE_GENI_S_CMD_CTRL_REG); 336 qcom_geni_serial_poll_bit(uport, SE_GENI_S_CMD_CTRL_REG, 337 S_GENI_CMD_ABORT, false); 338 writel(irq_clear, uport->membase + SE_GENI_S_IRQ_CLEAR); 339 writel(FORCE_DEFAULT, uport->membase + GENI_FORCE_DEFAULT_REG); 340 } 341 342 #ifdef CONFIG_CONSOLE_POLL 343 344 static int qcom_geni_serial_get_char(struct uart_port *uport) 345 { 346 struct qcom_geni_private_data *private_data = uport->private_data; 347 u32 status; 348 u32 word_cnt; 349 int ret; 350 351 if (!private_data->poll_cached_bytes_cnt) { 352 status = readl(uport->membase + SE_GENI_M_IRQ_STATUS); 353 writel(status, uport->membase + SE_GENI_M_IRQ_CLEAR); 354 355 status = readl(uport->membase + SE_GENI_S_IRQ_STATUS); 356 writel(status, uport->membase + SE_GENI_S_IRQ_CLEAR); 357 358 status = readl(uport->membase + SE_GENI_RX_FIFO_STATUS); 359 word_cnt = status & RX_FIFO_WC_MSK; 360 if (!word_cnt) 361 return NO_POLL_CHAR; 362 363 if (word_cnt == 1 && (status & RX_LAST)) 364 /* 365 * NOTE: If RX_LAST_BYTE_VALID is 0 it needs to be 366 * treated as if it was BYTES_PER_FIFO_WORD. 367 */ 368 private_data->poll_cached_bytes_cnt = 369 (status & RX_LAST_BYTE_VALID_MSK) >> 370 RX_LAST_BYTE_VALID_SHFT; 371 372 if (private_data->poll_cached_bytes_cnt == 0) 373 private_data->poll_cached_bytes_cnt = BYTES_PER_FIFO_WORD; 374 375 private_data->poll_cached_bytes = 376 readl(uport->membase + SE_GENI_RX_FIFOn); 377 } 378 379 private_data->poll_cached_bytes_cnt--; 380 ret = private_data->poll_cached_bytes & 0xff; 381 private_data->poll_cached_bytes >>= 8; 382 383 return ret; 384 } 385 386 static void qcom_geni_serial_poll_put_char(struct uart_port *uport, 387 unsigned char c) 388 { 389 writel(DEF_TX_WM, uport->membase + SE_GENI_TX_WATERMARK_REG); 390 qcom_geni_serial_setup_tx(uport, 1); 391 WARN_ON(!qcom_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS, 392 M_TX_FIFO_WATERMARK_EN, true)); 393 writel(c, uport->membase + SE_GENI_TX_FIFOn); 394 writel(M_TX_FIFO_WATERMARK_EN, uport->membase + SE_GENI_M_IRQ_CLEAR); 395 qcom_geni_serial_poll_tx_done(uport); 396 } 397 #endif 398 399 #ifdef CONFIG_SERIAL_QCOM_GENI_CONSOLE 400 static void qcom_geni_serial_wr_char(struct uart_port *uport, int ch) 401 { 402 struct qcom_geni_private_data *private_data = uport->private_data; 403 404 private_data->write_cached_bytes = 405 (private_data->write_cached_bytes >> 8) | (ch << 24); 406 private_data->write_cached_bytes_cnt++; 407 408 if (private_data->write_cached_bytes_cnt == BYTES_PER_FIFO_WORD) { 409 writel(private_data->write_cached_bytes, 410 uport->membase + SE_GENI_TX_FIFOn); 411 private_data->write_cached_bytes_cnt = 0; 412 } 413 } 414 415 static void 416 __qcom_geni_serial_console_write(struct uart_port *uport, const char *s, 417 unsigned int count) 418 { 419 struct qcom_geni_private_data *private_data = uport->private_data; 420 421 int i; 422 u32 bytes_to_send = count; 423 424 for (i = 0; i < count; i++) { 425 /* 426 * uart_console_write() adds a carriage return for each newline. 427 * Account for additional bytes to be written. 428 */ 429 if (s[i] == '\n') 430 bytes_to_send++; 431 } 432 433 writel(DEF_TX_WM, uport->membase + SE_GENI_TX_WATERMARK_REG); 434 qcom_geni_serial_setup_tx(uport, bytes_to_send); 435 for (i = 0; i < count; ) { 436 size_t chars_to_write = 0; 437 size_t avail = DEF_FIFO_DEPTH_WORDS - DEF_TX_WM; 438 439 /* 440 * If the WM bit never set, then the Tx state machine is not 441 * in a valid state, so break, cancel/abort any existing 442 * command. Unfortunately the current data being written is 443 * lost. 444 */ 445 if (!qcom_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS, 446 M_TX_FIFO_WATERMARK_EN, true)) 447 break; 448 chars_to_write = min_t(size_t, count - i, avail / 2); 449 uart_console_write(uport, s + i, chars_to_write, 450 qcom_geni_serial_wr_char); 451 writel(M_TX_FIFO_WATERMARK_EN, uport->membase + 452 SE_GENI_M_IRQ_CLEAR); 453 i += chars_to_write; 454 } 455 456 if (private_data->write_cached_bytes_cnt) { 457 private_data->write_cached_bytes >>= BITS_PER_BYTE * 458 (BYTES_PER_FIFO_WORD - private_data->write_cached_bytes_cnt); 459 writel(private_data->write_cached_bytes, 460 uport->membase + SE_GENI_TX_FIFOn); 461 private_data->write_cached_bytes_cnt = 0; 462 } 463 464 qcom_geni_serial_poll_tx_done(uport); 465 } 466 467 static void qcom_geni_serial_console_write(struct console *co, const char *s, 468 unsigned int count) 469 { 470 struct uart_port *uport; 471 struct qcom_geni_serial_port *port; 472 bool locked = true; 473 unsigned long flags; 474 u32 geni_status; 475 u32 irq_en; 476 477 WARN_ON(co->index < 0 || co->index >= GENI_UART_CONS_PORTS); 478 479 port = get_port_from_line(co->index, true); 480 if (IS_ERR(port)) 481 return; 482 483 uport = &port->uport; 484 if (oops_in_progress) 485 locked = spin_trylock_irqsave(&uport->lock, flags); 486 else 487 spin_lock_irqsave(&uport->lock, flags); 488 489 geni_status = readl(uport->membase + SE_GENI_STATUS); 490 491 /* Cancel the current write to log the fault */ 492 if (!locked) { 493 geni_se_cancel_m_cmd(&port->se); 494 if (!qcom_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS, 495 M_CMD_CANCEL_EN, true)) { 496 geni_se_abort_m_cmd(&port->se); 497 qcom_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS, 498 M_CMD_ABORT_EN, true); 499 writel(M_CMD_ABORT_EN, uport->membase + 500 SE_GENI_M_IRQ_CLEAR); 501 } 502 writel(M_CMD_CANCEL_EN, uport->membase + SE_GENI_M_IRQ_CLEAR); 503 } else if ((geni_status & M_GENI_CMD_ACTIVE) && !port->tx_remaining) { 504 /* 505 * It seems we can't interrupt existing transfers if all data 506 * has been sent, in which case we need to look for done first. 507 */ 508 qcom_geni_serial_poll_tx_done(uport); 509 510 if (uart_circ_chars_pending(&uport->state->xmit)) { 511 irq_en = readl(uport->membase + SE_GENI_M_IRQ_EN); 512 writel(irq_en | M_TX_FIFO_WATERMARK_EN, 513 uport->membase + SE_GENI_M_IRQ_EN); 514 } 515 } 516 517 __qcom_geni_serial_console_write(uport, s, count); 518 519 if (port->tx_remaining) 520 qcom_geni_serial_setup_tx(uport, port->tx_remaining); 521 522 if (locked) 523 spin_unlock_irqrestore(&uport->lock, flags); 524 } 525 526 static int handle_rx_console(struct uart_port *uport, u32 bytes, bool drop) 527 { 528 u32 i; 529 unsigned char buf[sizeof(u32)]; 530 struct tty_port *tport; 531 struct qcom_geni_serial_port *port = to_dev_port(uport, uport); 532 533 tport = &uport->state->port; 534 for (i = 0; i < bytes; ) { 535 int c; 536 int chunk = min_t(int, bytes - i, BYTES_PER_FIFO_WORD); 537 538 ioread32_rep(uport->membase + SE_GENI_RX_FIFOn, buf, 1); 539 i += chunk; 540 if (drop) 541 continue; 542 543 for (c = 0; c < chunk; c++) { 544 int sysrq; 545 546 uport->icount.rx++; 547 if (port->brk && buf[c] == 0) { 548 port->brk = false; 549 if (uart_handle_break(uport)) 550 continue; 551 } 552 553 sysrq = uart_prepare_sysrq_char(uport, buf[c]); 554 555 if (!sysrq) 556 tty_insert_flip_char(tport, buf[c], TTY_NORMAL); 557 } 558 } 559 if (!drop) 560 tty_flip_buffer_push(tport); 561 return 0; 562 } 563 #else 564 static int handle_rx_console(struct uart_port *uport, u32 bytes, bool drop) 565 { 566 return -EPERM; 567 } 568 569 #endif /* CONFIG_SERIAL_QCOM_GENI_CONSOLE */ 570 571 static int handle_rx_uart(struct uart_port *uport, u32 bytes, bool drop) 572 { 573 struct tty_port *tport; 574 struct qcom_geni_serial_port *port = to_dev_port(uport, uport); 575 u32 num_bytes_pw = port->tx_fifo_width / BITS_PER_BYTE; 576 u32 words = ALIGN(bytes, num_bytes_pw) / num_bytes_pw; 577 int ret; 578 579 tport = &uport->state->port; 580 ioread32_rep(uport->membase + SE_GENI_RX_FIFOn, port->rx_fifo, words); 581 if (drop) 582 return 0; 583 584 ret = tty_insert_flip_string(tport, port->rx_fifo, bytes); 585 if (ret != bytes) { 586 dev_err(uport->dev, "%s:Unable to push data ret %d_bytes %d\n", 587 __func__, ret, bytes); 588 WARN_ON_ONCE(1); 589 } 590 uport->icount.rx += ret; 591 tty_flip_buffer_push(tport); 592 return ret; 593 } 594 595 static void qcom_geni_serial_start_tx(struct uart_port *uport) 596 { 597 u32 irq_en; 598 u32 status; 599 600 status = readl(uport->membase + SE_GENI_STATUS); 601 if (status & M_GENI_CMD_ACTIVE) 602 return; 603 604 if (!qcom_geni_serial_tx_empty(uport)) 605 return; 606 607 irq_en = readl(uport->membase + SE_GENI_M_IRQ_EN); 608 irq_en |= M_TX_FIFO_WATERMARK_EN | M_CMD_DONE_EN; 609 610 writel(DEF_TX_WM, uport->membase + SE_GENI_TX_WATERMARK_REG); 611 writel(irq_en, uport->membase + SE_GENI_M_IRQ_EN); 612 } 613 614 static void qcom_geni_serial_stop_tx(struct uart_port *uport) 615 { 616 u32 irq_en; 617 u32 status; 618 struct qcom_geni_serial_port *port = to_dev_port(uport, uport); 619 620 irq_en = readl(uport->membase + SE_GENI_M_IRQ_EN); 621 irq_en &= ~(M_CMD_DONE_EN | M_TX_FIFO_WATERMARK_EN); 622 writel(0, uport->membase + SE_GENI_TX_WATERMARK_REG); 623 writel(irq_en, uport->membase + SE_GENI_M_IRQ_EN); 624 status = readl(uport->membase + SE_GENI_STATUS); 625 /* Possible stop tx is called multiple times. */ 626 if (!(status & M_GENI_CMD_ACTIVE)) 627 return; 628 629 geni_se_cancel_m_cmd(&port->se); 630 if (!qcom_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS, 631 M_CMD_CANCEL_EN, true)) { 632 geni_se_abort_m_cmd(&port->se); 633 qcom_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS, 634 M_CMD_ABORT_EN, true); 635 writel(M_CMD_ABORT_EN, uport->membase + SE_GENI_M_IRQ_CLEAR); 636 } 637 writel(M_CMD_CANCEL_EN, uport->membase + SE_GENI_M_IRQ_CLEAR); 638 } 639 640 static void qcom_geni_serial_start_rx(struct uart_port *uport) 641 { 642 u32 irq_en; 643 u32 status; 644 struct qcom_geni_serial_port *port = to_dev_port(uport, uport); 645 646 status = readl(uport->membase + SE_GENI_STATUS); 647 if (status & S_GENI_CMD_ACTIVE) 648 qcom_geni_serial_stop_rx(uport); 649 650 geni_se_setup_s_cmd(&port->se, UART_START_READ, 0); 651 652 irq_en = readl(uport->membase + SE_GENI_S_IRQ_EN); 653 irq_en |= S_RX_FIFO_WATERMARK_EN | S_RX_FIFO_LAST_EN; 654 writel(irq_en, uport->membase + SE_GENI_S_IRQ_EN); 655 656 irq_en = readl(uport->membase + SE_GENI_M_IRQ_EN); 657 irq_en |= M_RX_FIFO_WATERMARK_EN | M_RX_FIFO_LAST_EN; 658 writel(irq_en, uport->membase + SE_GENI_M_IRQ_EN); 659 } 660 661 static void qcom_geni_serial_stop_rx(struct uart_port *uport) 662 { 663 u32 irq_en; 664 u32 status; 665 struct qcom_geni_serial_port *port = to_dev_port(uport, uport); 666 u32 s_irq_status; 667 668 irq_en = readl(uport->membase + SE_GENI_S_IRQ_EN); 669 irq_en &= ~(S_RX_FIFO_WATERMARK_EN | S_RX_FIFO_LAST_EN); 670 writel(irq_en, uport->membase + SE_GENI_S_IRQ_EN); 671 672 irq_en = readl(uport->membase + SE_GENI_M_IRQ_EN); 673 irq_en &= ~(M_RX_FIFO_WATERMARK_EN | M_RX_FIFO_LAST_EN); 674 writel(irq_en, uport->membase + SE_GENI_M_IRQ_EN); 675 676 status = readl(uport->membase + SE_GENI_STATUS); 677 /* Possible stop rx is called multiple times. */ 678 if (!(status & S_GENI_CMD_ACTIVE)) 679 return; 680 681 geni_se_cancel_s_cmd(&port->se); 682 qcom_geni_serial_poll_bit(uport, SE_GENI_S_IRQ_STATUS, 683 S_CMD_CANCEL_EN, true); 684 /* 685 * If timeout occurs secondary engine remains active 686 * and Abort sequence is executed. 687 */ 688 s_irq_status = readl(uport->membase + SE_GENI_S_IRQ_STATUS); 689 /* Flush the Rx buffer */ 690 if (s_irq_status & S_RX_FIFO_LAST_EN) 691 qcom_geni_serial_handle_rx(uport, true); 692 writel(s_irq_status, uport->membase + SE_GENI_S_IRQ_CLEAR); 693 694 status = readl(uport->membase + SE_GENI_STATUS); 695 if (status & S_GENI_CMD_ACTIVE) 696 qcom_geni_serial_abort_rx(uport); 697 } 698 699 static void qcom_geni_serial_handle_rx(struct uart_port *uport, bool drop) 700 { 701 u32 status; 702 u32 word_cnt; 703 u32 last_word_byte_cnt; 704 u32 last_word_partial; 705 u32 total_bytes; 706 struct qcom_geni_serial_port *port = to_dev_port(uport, uport); 707 708 status = readl(uport->membase + SE_GENI_RX_FIFO_STATUS); 709 word_cnt = status & RX_FIFO_WC_MSK; 710 last_word_partial = status & RX_LAST; 711 last_word_byte_cnt = (status & RX_LAST_BYTE_VALID_MSK) >> 712 RX_LAST_BYTE_VALID_SHFT; 713 714 if (!word_cnt) 715 return; 716 total_bytes = BYTES_PER_FIFO_WORD * (word_cnt - 1); 717 if (last_word_partial && last_word_byte_cnt) 718 total_bytes += last_word_byte_cnt; 719 else 720 total_bytes += BYTES_PER_FIFO_WORD; 721 port->handle_rx(uport, total_bytes, drop); 722 } 723 724 static void qcom_geni_serial_handle_tx(struct uart_port *uport, bool done, 725 bool active) 726 { 727 struct qcom_geni_serial_port *port = to_dev_port(uport, uport); 728 struct circ_buf *xmit = &uport->state->xmit; 729 size_t avail; 730 size_t remaining; 731 size_t pending; 732 int i; 733 u32 status; 734 u32 irq_en; 735 unsigned int chunk; 736 int tail; 737 738 status = readl(uport->membase + SE_GENI_TX_FIFO_STATUS); 739 740 /* Complete the current tx command before taking newly added data */ 741 if (active) 742 pending = port->tx_remaining; 743 else 744 pending = uart_circ_chars_pending(xmit); 745 746 /* All data has been transmitted and acknowledged as received */ 747 if (!pending && !status && done) { 748 qcom_geni_serial_stop_tx(uport); 749 goto out_write_wakeup; 750 } 751 752 avail = port->tx_fifo_depth - (status & TX_FIFO_WC); 753 avail *= BYTES_PER_FIFO_WORD; 754 755 tail = xmit->tail; 756 chunk = min(avail, pending); 757 if (!chunk) 758 goto out_write_wakeup; 759 760 if (!port->tx_remaining) { 761 qcom_geni_serial_setup_tx(uport, pending); 762 port->tx_remaining = pending; 763 764 irq_en = readl(uport->membase + SE_GENI_M_IRQ_EN); 765 if (!(irq_en & M_TX_FIFO_WATERMARK_EN)) 766 writel(irq_en | M_TX_FIFO_WATERMARK_EN, 767 uport->membase + SE_GENI_M_IRQ_EN); 768 } 769 770 remaining = chunk; 771 for (i = 0; i < chunk; ) { 772 unsigned int tx_bytes; 773 u8 buf[sizeof(u32)]; 774 int c; 775 776 memset(buf, 0, sizeof(buf)); 777 tx_bytes = min_t(size_t, remaining, BYTES_PER_FIFO_WORD); 778 779 for (c = 0; c < tx_bytes ; c++) { 780 buf[c] = xmit->buf[tail++]; 781 tail &= UART_XMIT_SIZE - 1; 782 } 783 784 iowrite32_rep(uport->membase + SE_GENI_TX_FIFOn, buf, 1); 785 786 i += tx_bytes; 787 uport->icount.tx += tx_bytes; 788 remaining -= tx_bytes; 789 port->tx_remaining -= tx_bytes; 790 } 791 792 xmit->tail = tail; 793 794 /* 795 * The tx fifo watermark is level triggered and latched. Though we had 796 * cleared it in qcom_geni_serial_isr it will have already reasserted 797 * so we must clear it again here after our writes. 798 */ 799 writel(M_TX_FIFO_WATERMARK_EN, 800 uport->membase + SE_GENI_M_IRQ_CLEAR); 801 802 out_write_wakeup: 803 if (!port->tx_remaining) { 804 irq_en = readl(uport->membase + SE_GENI_M_IRQ_EN); 805 if (irq_en & M_TX_FIFO_WATERMARK_EN) 806 writel(irq_en & ~M_TX_FIFO_WATERMARK_EN, 807 uport->membase + SE_GENI_M_IRQ_EN); 808 } 809 810 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) 811 uart_write_wakeup(uport); 812 } 813 814 static irqreturn_t qcom_geni_serial_isr(int isr, void *dev) 815 { 816 u32 m_irq_en; 817 u32 m_irq_status; 818 u32 s_irq_status; 819 u32 geni_status; 820 struct uart_port *uport = dev; 821 bool drop_rx = false; 822 struct tty_port *tport = &uport->state->port; 823 struct qcom_geni_serial_port *port = to_dev_port(uport, uport); 824 825 if (uport->suspended) 826 return IRQ_NONE; 827 828 spin_lock(&uport->lock); 829 830 m_irq_status = readl(uport->membase + SE_GENI_M_IRQ_STATUS); 831 s_irq_status = readl(uport->membase + SE_GENI_S_IRQ_STATUS); 832 geni_status = readl(uport->membase + SE_GENI_STATUS); 833 m_irq_en = readl(uport->membase + SE_GENI_M_IRQ_EN); 834 writel(m_irq_status, uport->membase + SE_GENI_M_IRQ_CLEAR); 835 writel(s_irq_status, uport->membase + SE_GENI_S_IRQ_CLEAR); 836 837 if (WARN_ON(m_irq_status & M_ILLEGAL_CMD_EN)) 838 goto out_unlock; 839 840 if (s_irq_status & S_RX_FIFO_WR_ERR_EN) { 841 uport->icount.overrun++; 842 tty_insert_flip_char(tport, 0, TTY_OVERRUN); 843 } 844 845 if (m_irq_status & m_irq_en & (M_TX_FIFO_WATERMARK_EN | M_CMD_DONE_EN)) 846 qcom_geni_serial_handle_tx(uport, m_irq_status & M_CMD_DONE_EN, 847 geni_status & M_GENI_CMD_ACTIVE); 848 849 if (s_irq_status & S_GP_IRQ_0_EN || s_irq_status & S_GP_IRQ_1_EN) { 850 if (s_irq_status & S_GP_IRQ_0_EN) 851 uport->icount.parity++; 852 drop_rx = true; 853 } else if (s_irq_status & S_GP_IRQ_2_EN || 854 s_irq_status & S_GP_IRQ_3_EN) { 855 uport->icount.brk++; 856 port->brk = true; 857 } 858 859 if (s_irq_status & S_RX_FIFO_WATERMARK_EN || 860 s_irq_status & S_RX_FIFO_LAST_EN) 861 qcom_geni_serial_handle_rx(uport, drop_rx); 862 863 out_unlock: 864 uart_unlock_and_check_sysrq(uport); 865 866 return IRQ_HANDLED; 867 } 868 869 static void get_tx_fifo_size(struct qcom_geni_serial_port *port) 870 { 871 struct uart_port *uport; 872 873 uport = &port->uport; 874 port->tx_fifo_depth = geni_se_get_tx_fifo_depth(&port->se); 875 port->tx_fifo_width = geni_se_get_tx_fifo_width(&port->se); 876 port->rx_fifo_depth = geni_se_get_rx_fifo_depth(&port->se); 877 uport->fifosize = 878 (port->tx_fifo_depth * port->tx_fifo_width) / BITS_PER_BYTE; 879 } 880 881 882 static void qcom_geni_serial_shutdown(struct uart_port *uport) 883 { 884 disable_irq(uport->irq); 885 } 886 887 static int qcom_geni_serial_port_setup(struct uart_port *uport) 888 { 889 struct qcom_geni_serial_port *port = to_dev_port(uport, uport); 890 u32 rxstale = DEFAULT_BITS_PER_CHAR * STALE_TIMEOUT; 891 u32 proto; 892 u32 pin_swap; 893 894 proto = geni_se_read_proto(&port->se); 895 if (proto != GENI_SE_UART) { 896 dev_err(uport->dev, "Invalid FW loaded, proto: %d\n", proto); 897 return -ENXIO; 898 } 899 900 qcom_geni_serial_stop_rx(uport); 901 902 get_tx_fifo_size(port); 903 904 writel(rxstale, uport->membase + SE_UART_RX_STALE_CNT); 905 906 pin_swap = readl(uport->membase + SE_UART_IO_MACRO_CTRL); 907 if (port->rx_tx_swap) { 908 pin_swap &= ~DEFAULT_IO_MACRO_IO2_IO3_MASK; 909 pin_swap |= IO_MACRO_IO2_IO3_SWAP; 910 } 911 if (port->cts_rts_swap) { 912 pin_swap &= ~DEFAULT_IO_MACRO_IO0_IO1_MASK; 913 pin_swap |= IO_MACRO_IO0_SEL; 914 } 915 /* Configure this register if RX-TX, CTS-RTS pins are swapped */ 916 if (port->rx_tx_swap || port->cts_rts_swap) 917 writel(pin_swap, uport->membase + SE_UART_IO_MACRO_CTRL); 918 919 /* 920 * Make an unconditional cancel on the main sequencer to reset 921 * it else we could end up in data loss scenarios. 922 */ 923 if (uart_console(uport)) 924 qcom_geni_serial_poll_tx_done(uport); 925 geni_se_config_packing(&port->se, BITS_PER_BYTE, BYTES_PER_FIFO_WORD, 926 false, true, true); 927 geni_se_init(&port->se, UART_RX_WM, port->rx_fifo_depth - 2); 928 geni_se_select_mode(&port->se, GENI_SE_FIFO); 929 port->setup = true; 930 931 return 0; 932 } 933 934 static int qcom_geni_serial_startup(struct uart_port *uport) 935 { 936 int ret; 937 struct qcom_geni_serial_port *port = to_dev_port(uport, uport); 938 939 if (!port->setup) { 940 ret = qcom_geni_serial_port_setup(uport); 941 if (ret) 942 return ret; 943 } 944 enable_irq(uport->irq); 945 946 return 0; 947 } 948 949 static unsigned long get_clk_cfg(unsigned long clk_freq) 950 { 951 int i; 952 953 for (i = 0; i < ARRAY_SIZE(root_freq); i++) { 954 if (!(root_freq[i] % clk_freq)) 955 return root_freq[i]; 956 } 957 return 0; 958 } 959 960 static unsigned long get_clk_div_rate(unsigned int baud, 961 unsigned int sampling_rate, unsigned int *clk_div) 962 { 963 unsigned long ser_clk; 964 unsigned long desired_clk; 965 966 desired_clk = baud * sampling_rate; 967 ser_clk = get_clk_cfg(desired_clk); 968 if (!ser_clk) { 969 pr_err("%s: Can't find matching DFS entry for baud %d\n", 970 __func__, baud); 971 return ser_clk; 972 } 973 974 *clk_div = ser_clk / desired_clk; 975 return ser_clk; 976 } 977 978 static void qcom_geni_serial_set_termios(struct uart_port *uport, 979 struct ktermios *termios, struct ktermios *old) 980 { 981 unsigned int baud; 982 u32 bits_per_char; 983 u32 tx_trans_cfg; 984 u32 tx_parity_cfg; 985 u32 rx_trans_cfg; 986 u32 rx_parity_cfg; 987 u32 stop_bit_len; 988 unsigned int clk_div; 989 u32 ser_clk_cfg; 990 struct qcom_geni_serial_port *port = to_dev_port(uport, uport); 991 unsigned long clk_rate; 992 u32 ver, sampling_rate; 993 unsigned int avg_bw_core; 994 995 qcom_geni_serial_stop_rx(uport); 996 /* baud rate */ 997 baud = uart_get_baud_rate(uport, termios, old, 300, 4000000); 998 port->baud = baud; 999 1000 sampling_rate = UART_OVERSAMPLING; 1001 /* Sampling rate is halved for IP versions >= 2.5 */ 1002 ver = geni_se_get_qup_hw_version(&port->se); 1003 if (ver >= QUP_SE_VERSION_2_5) 1004 sampling_rate /= 2; 1005 1006 clk_rate = get_clk_div_rate(baud, sampling_rate, &clk_div); 1007 if (!clk_rate) 1008 goto out_restart_rx; 1009 1010 uport->uartclk = clk_rate; 1011 dev_pm_opp_set_rate(uport->dev, clk_rate); 1012 ser_clk_cfg = SER_CLK_EN; 1013 ser_clk_cfg |= clk_div << CLK_DIV_SHFT; 1014 1015 /* 1016 * Bump up BW vote on CPU and CORE path as driver supports FIFO mode 1017 * only. 1018 */ 1019 avg_bw_core = (baud > 115200) ? Bps_to_icc(CORE_2X_50_MHZ) 1020 : GENI_DEFAULT_BW; 1021 port->se.icc_paths[GENI_TO_CORE].avg_bw = avg_bw_core; 1022 port->se.icc_paths[CPU_TO_GENI].avg_bw = Bps_to_icc(baud); 1023 geni_icc_set_bw(&port->se); 1024 1025 /* parity */ 1026 tx_trans_cfg = readl(uport->membase + SE_UART_TX_TRANS_CFG); 1027 tx_parity_cfg = readl(uport->membase + SE_UART_TX_PARITY_CFG); 1028 rx_trans_cfg = readl(uport->membase + SE_UART_RX_TRANS_CFG); 1029 rx_parity_cfg = readl(uport->membase + SE_UART_RX_PARITY_CFG); 1030 if (termios->c_cflag & PARENB) { 1031 tx_trans_cfg |= UART_TX_PAR_EN; 1032 rx_trans_cfg |= UART_RX_PAR_EN; 1033 tx_parity_cfg |= PAR_CALC_EN; 1034 rx_parity_cfg |= PAR_CALC_EN; 1035 if (termios->c_cflag & PARODD) { 1036 tx_parity_cfg |= PAR_ODD; 1037 rx_parity_cfg |= PAR_ODD; 1038 } else if (termios->c_cflag & CMSPAR) { 1039 tx_parity_cfg |= PAR_SPACE; 1040 rx_parity_cfg |= PAR_SPACE; 1041 } else { 1042 tx_parity_cfg |= PAR_EVEN; 1043 rx_parity_cfg |= PAR_EVEN; 1044 } 1045 } else { 1046 tx_trans_cfg &= ~UART_TX_PAR_EN; 1047 rx_trans_cfg &= ~UART_RX_PAR_EN; 1048 tx_parity_cfg &= ~PAR_CALC_EN; 1049 rx_parity_cfg &= ~PAR_CALC_EN; 1050 } 1051 1052 /* bits per char */ 1053 switch (termios->c_cflag & CSIZE) { 1054 case CS5: 1055 bits_per_char = 5; 1056 break; 1057 case CS6: 1058 bits_per_char = 6; 1059 break; 1060 case CS7: 1061 bits_per_char = 7; 1062 break; 1063 case CS8: 1064 default: 1065 bits_per_char = 8; 1066 break; 1067 } 1068 1069 /* stop bits */ 1070 if (termios->c_cflag & CSTOPB) 1071 stop_bit_len = TX_STOP_BIT_LEN_2; 1072 else 1073 stop_bit_len = TX_STOP_BIT_LEN_1; 1074 1075 /* flow control, clear the CTS_MASK bit if using flow control. */ 1076 if (termios->c_cflag & CRTSCTS) 1077 tx_trans_cfg &= ~UART_CTS_MASK; 1078 else 1079 tx_trans_cfg |= UART_CTS_MASK; 1080 1081 if (baud) 1082 uart_update_timeout(uport, termios->c_cflag, baud); 1083 1084 if (!uart_console(uport)) 1085 writel(port->loopback, 1086 uport->membase + SE_UART_LOOPBACK_CFG); 1087 writel(tx_trans_cfg, uport->membase + SE_UART_TX_TRANS_CFG); 1088 writel(tx_parity_cfg, uport->membase + SE_UART_TX_PARITY_CFG); 1089 writel(rx_trans_cfg, uport->membase + SE_UART_RX_TRANS_CFG); 1090 writel(rx_parity_cfg, uport->membase + SE_UART_RX_PARITY_CFG); 1091 writel(bits_per_char, uport->membase + SE_UART_TX_WORD_LEN); 1092 writel(bits_per_char, uport->membase + SE_UART_RX_WORD_LEN); 1093 writel(stop_bit_len, uport->membase + SE_UART_TX_STOP_BIT_LEN); 1094 writel(ser_clk_cfg, uport->membase + GENI_SER_M_CLK_CFG); 1095 writel(ser_clk_cfg, uport->membase + GENI_SER_S_CLK_CFG); 1096 out_restart_rx: 1097 qcom_geni_serial_start_rx(uport); 1098 } 1099 1100 static unsigned int qcom_geni_serial_tx_empty(struct uart_port *uport) 1101 { 1102 return !readl(uport->membase + SE_GENI_TX_FIFO_STATUS); 1103 } 1104 1105 #ifdef CONFIG_SERIAL_QCOM_GENI_CONSOLE 1106 static int qcom_geni_console_setup(struct console *co, char *options) 1107 { 1108 struct uart_port *uport; 1109 struct qcom_geni_serial_port *port; 1110 int baud = 115200; 1111 int bits = 8; 1112 int parity = 'n'; 1113 int flow = 'n'; 1114 int ret; 1115 1116 if (co->index >= GENI_UART_CONS_PORTS || co->index < 0) 1117 return -ENXIO; 1118 1119 port = get_port_from_line(co->index, true); 1120 if (IS_ERR(port)) { 1121 pr_err("Invalid line %d\n", co->index); 1122 return PTR_ERR(port); 1123 } 1124 1125 uport = &port->uport; 1126 1127 if (unlikely(!uport->membase)) 1128 return -ENXIO; 1129 1130 if (!port->setup) { 1131 ret = qcom_geni_serial_port_setup(uport); 1132 if (ret) 1133 return ret; 1134 } 1135 1136 if (options) 1137 uart_parse_options(options, &baud, &parity, &bits, &flow); 1138 1139 return uart_set_options(uport, co, baud, parity, bits, flow); 1140 } 1141 1142 static void qcom_geni_serial_earlycon_write(struct console *con, 1143 const char *s, unsigned int n) 1144 { 1145 struct earlycon_device *dev = con->data; 1146 1147 __qcom_geni_serial_console_write(&dev->port, s, n); 1148 } 1149 1150 #ifdef CONFIG_CONSOLE_POLL 1151 static int qcom_geni_serial_earlycon_read(struct console *con, 1152 char *s, unsigned int n) 1153 { 1154 struct earlycon_device *dev = con->data; 1155 struct uart_port *uport = &dev->port; 1156 int num_read = 0; 1157 int ch; 1158 1159 while (num_read < n) { 1160 ch = qcom_geni_serial_get_char(uport); 1161 if (ch == NO_POLL_CHAR) 1162 break; 1163 s[num_read++] = ch; 1164 } 1165 1166 return num_read; 1167 } 1168 1169 static void __init qcom_geni_serial_enable_early_read(struct geni_se *se, 1170 struct console *con) 1171 { 1172 geni_se_setup_s_cmd(se, UART_START_READ, 0); 1173 con->read = qcom_geni_serial_earlycon_read; 1174 } 1175 #else 1176 static inline void qcom_geni_serial_enable_early_read(struct geni_se *se, 1177 struct console *con) { } 1178 #endif 1179 1180 static struct qcom_geni_private_data earlycon_private_data; 1181 1182 static int __init qcom_geni_serial_earlycon_setup(struct earlycon_device *dev, 1183 const char *opt) 1184 { 1185 struct uart_port *uport = &dev->port; 1186 u32 tx_trans_cfg; 1187 u32 tx_parity_cfg = 0; /* Disable Tx Parity */ 1188 u32 rx_trans_cfg = 0; 1189 u32 rx_parity_cfg = 0; /* Disable Rx Parity */ 1190 u32 stop_bit_len = 0; /* Default stop bit length - 1 bit */ 1191 u32 bits_per_char; 1192 struct geni_se se; 1193 1194 if (!uport->membase) 1195 return -EINVAL; 1196 1197 uport->private_data = &earlycon_private_data; 1198 1199 memset(&se, 0, sizeof(se)); 1200 se.base = uport->membase; 1201 if (geni_se_read_proto(&se) != GENI_SE_UART) 1202 return -ENXIO; 1203 /* 1204 * Ignore Flow control. 1205 * n = 8. 1206 */ 1207 tx_trans_cfg = UART_CTS_MASK; 1208 bits_per_char = BITS_PER_BYTE; 1209 1210 /* 1211 * Make an unconditional cancel on the main sequencer to reset 1212 * it else we could end up in data loss scenarios. 1213 */ 1214 qcom_geni_serial_poll_tx_done(uport); 1215 qcom_geni_serial_abort_rx(uport); 1216 geni_se_config_packing(&se, BITS_PER_BYTE, BYTES_PER_FIFO_WORD, 1217 false, true, true); 1218 geni_se_init(&se, DEF_FIFO_DEPTH_WORDS / 2, DEF_FIFO_DEPTH_WORDS - 2); 1219 geni_se_select_mode(&se, GENI_SE_FIFO); 1220 1221 writel(tx_trans_cfg, uport->membase + SE_UART_TX_TRANS_CFG); 1222 writel(tx_parity_cfg, uport->membase + SE_UART_TX_PARITY_CFG); 1223 writel(rx_trans_cfg, uport->membase + SE_UART_RX_TRANS_CFG); 1224 writel(rx_parity_cfg, uport->membase + SE_UART_RX_PARITY_CFG); 1225 writel(bits_per_char, uport->membase + SE_UART_TX_WORD_LEN); 1226 writel(bits_per_char, uport->membase + SE_UART_RX_WORD_LEN); 1227 writel(stop_bit_len, uport->membase + SE_UART_TX_STOP_BIT_LEN); 1228 1229 dev->con->write = qcom_geni_serial_earlycon_write; 1230 dev->con->setup = NULL; 1231 qcom_geni_serial_enable_early_read(&se, dev->con); 1232 1233 return 0; 1234 } 1235 OF_EARLYCON_DECLARE(qcom_geni, "qcom,geni-debug-uart", 1236 qcom_geni_serial_earlycon_setup); 1237 1238 static int __init console_register(struct uart_driver *drv) 1239 { 1240 return uart_register_driver(drv); 1241 } 1242 1243 static void console_unregister(struct uart_driver *drv) 1244 { 1245 uart_unregister_driver(drv); 1246 } 1247 1248 static struct console cons_ops = { 1249 .name = "ttyMSM", 1250 .write = qcom_geni_serial_console_write, 1251 .device = uart_console_device, 1252 .setup = qcom_geni_console_setup, 1253 .flags = CON_PRINTBUFFER, 1254 .index = -1, 1255 .data = &qcom_geni_console_driver, 1256 }; 1257 1258 static struct uart_driver qcom_geni_console_driver = { 1259 .owner = THIS_MODULE, 1260 .driver_name = "qcom_geni_console", 1261 .dev_name = "ttyMSM", 1262 .nr = GENI_UART_CONS_PORTS, 1263 .cons = &cons_ops, 1264 }; 1265 #else 1266 static int console_register(struct uart_driver *drv) 1267 { 1268 return 0; 1269 } 1270 1271 static void console_unregister(struct uart_driver *drv) 1272 { 1273 } 1274 #endif /* CONFIG_SERIAL_QCOM_GENI_CONSOLE */ 1275 1276 static struct uart_driver qcom_geni_uart_driver = { 1277 .owner = THIS_MODULE, 1278 .driver_name = "qcom_geni_uart", 1279 .dev_name = "ttyHS", 1280 .nr = GENI_UART_PORTS, 1281 }; 1282 1283 static void qcom_geni_serial_pm(struct uart_port *uport, 1284 unsigned int new_state, unsigned int old_state) 1285 { 1286 struct qcom_geni_serial_port *port = to_dev_port(uport, uport); 1287 1288 /* If we've never been called, treat it as off */ 1289 if (old_state == UART_PM_STATE_UNDEFINED) 1290 old_state = UART_PM_STATE_OFF; 1291 1292 if (new_state == UART_PM_STATE_ON && old_state == UART_PM_STATE_OFF) { 1293 geni_icc_enable(&port->se); 1294 geni_se_resources_on(&port->se); 1295 } else if (new_state == UART_PM_STATE_OFF && 1296 old_state == UART_PM_STATE_ON) { 1297 geni_se_resources_off(&port->se); 1298 geni_icc_disable(&port->se); 1299 } 1300 } 1301 1302 static const struct uart_ops qcom_geni_console_pops = { 1303 .tx_empty = qcom_geni_serial_tx_empty, 1304 .stop_tx = qcom_geni_serial_stop_tx, 1305 .start_tx = qcom_geni_serial_start_tx, 1306 .stop_rx = qcom_geni_serial_stop_rx, 1307 .set_termios = qcom_geni_serial_set_termios, 1308 .startup = qcom_geni_serial_startup, 1309 .request_port = qcom_geni_serial_request_port, 1310 .config_port = qcom_geni_serial_config_port, 1311 .shutdown = qcom_geni_serial_shutdown, 1312 .type = qcom_geni_serial_get_type, 1313 .set_mctrl = qcom_geni_serial_set_mctrl, 1314 .get_mctrl = qcom_geni_serial_get_mctrl, 1315 #ifdef CONFIG_CONSOLE_POLL 1316 .poll_get_char = qcom_geni_serial_get_char, 1317 .poll_put_char = qcom_geni_serial_poll_put_char, 1318 #endif 1319 .pm = qcom_geni_serial_pm, 1320 }; 1321 1322 static const struct uart_ops qcom_geni_uart_pops = { 1323 .tx_empty = qcom_geni_serial_tx_empty, 1324 .stop_tx = qcom_geni_serial_stop_tx, 1325 .start_tx = qcom_geni_serial_start_tx, 1326 .stop_rx = qcom_geni_serial_stop_rx, 1327 .set_termios = qcom_geni_serial_set_termios, 1328 .startup = qcom_geni_serial_startup, 1329 .request_port = qcom_geni_serial_request_port, 1330 .config_port = qcom_geni_serial_config_port, 1331 .shutdown = qcom_geni_serial_shutdown, 1332 .type = qcom_geni_serial_get_type, 1333 .set_mctrl = qcom_geni_serial_set_mctrl, 1334 .get_mctrl = qcom_geni_serial_get_mctrl, 1335 .pm = qcom_geni_serial_pm, 1336 }; 1337 1338 static int qcom_geni_serial_probe(struct platform_device *pdev) 1339 { 1340 int ret = 0; 1341 int line = -1; 1342 struct qcom_geni_serial_port *port; 1343 struct uart_port *uport; 1344 struct resource *res; 1345 int irq; 1346 bool console = false; 1347 struct uart_driver *drv; 1348 1349 if (of_device_is_compatible(pdev->dev.of_node, "qcom,geni-debug-uart")) 1350 console = true; 1351 1352 if (console) { 1353 drv = &qcom_geni_console_driver; 1354 line = of_alias_get_id(pdev->dev.of_node, "serial"); 1355 } else { 1356 drv = &qcom_geni_uart_driver; 1357 line = of_alias_get_id(pdev->dev.of_node, "hsuart"); 1358 } 1359 1360 port = get_port_from_line(line, console); 1361 if (IS_ERR(port)) { 1362 dev_err(&pdev->dev, "Invalid line %d\n", line); 1363 return PTR_ERR(port); 1364 } 1365 1366 uport = &port->uport; 1367 /* Don't allow 2 drivers to access the same port */ 1368 if (uport->private_data) 1369 return -ENODEV; 1370 1371 uport->dev = &pdev->dev; 1372 port->se.dev = &pdev->dev; 1373 port->se.wrapper = dev_get_drvdata(pdev->dev.parent); 1374 port->se.clk = devm_clk_get(&pdev->dev, "se"); 1375 if (IS_ERR(port->se.clk)) { 1376 ret = PTR_ERR(port->se.clk); 1377 dev_err(&pdev->dev, "Err getting SE Core clk %d\n", ret); 1378 return ret; 1379 } 1380 1381 res = platform_get_resource(pdev, IORESOURCE_MEM, 0); 1382 if (!res) 1383 return -EINVAL; 1384 uport->mapbase = res->start; 1385 1386 port->tx_fifo_depth = DEF_FIFO_DEPTH_WORDS; 1387 port->rx_fifo_depth = DEF_FIFO_DEPTH_WORDS; 1388 port->tx_fifo_width = DEF_FIFO_WIDTH_BITS; 1389 1390 if (!console) { 1391 port->rx_fifo = devm_kcalloc(uport->dev, 1392 port->rx_fifo_depth, sizeof(u32), GFP_KERNEL); 1393 if (!port->rx_fifo) 1394 return -ENOMEM; 1395 } 1396 1397 ret = geni_icc_get(&port->se, NULL); 1398 if (ret) 1399 return ret; 1400 port->se.icc_paths[GENI_TO_CORE].avg_bw = GENI_DEFAULT_BW; 1401 port->se.icc_paths[CPU_TO_GENI].avg_bw = GENI_DEFAULT_BW; 1402 1403 /* Set BW for register access */ 1404 ret = geni_icc_set_bw(&port->se); 1405 if (ret) 1406 return ret; 1407 1408 port->name = devm_kasprintf(uport->dev, GFP_KERNEL, 1409 "qcom_geni_serial_%s%d", 1410 uart_console(uport) ? "console" : "uart", uport->line); 1411 if (!port->name) 1412 return -ENOMEM; 1413 1414 irq = platform_get_irq(pdev, 0); 1415 if (irq < 0) 1416 return irq; 1417 uport->irq = irq; 1418 uport->has_sysrq = IS_ENABLED(CONFIG_SERIAL_QCOM_GENI_CONSOLE); 1419 1420 if (!console) 1421 port->wakeup_irq = platform_get_irq_optional(pdev, 1); 1422 1423 if (of_property_read_bool(pdev->dev.of_node, "rx-tx-swap")) 1424 port->rx_tx_swap = true; 1425 1426 if (of_property_read_bool(pdev->dev.of_node, "cts-rts-swap")) 1427 port->cts_rts_swap = true; 1428 1429 ret = devm_pm_opp_set_clkname(&pdev->dev, "se"); 1430 if (ret) 1431 return ret; 1432 /* OPP table is optional */ 1433 ret = devm_pm_opp_of_add_table(&pdev->dev); 1434 if (ret && ret != -ENODEV) { 1435 dev_err(&pdev->dev, "invalid OPP table in device tree\n"); 1436 return ret; 1437 } 1438 1439 port->private_data.drv = drv; 1440 uport->private_data = &port->private_data; 1441 platform_set_drvdata(pdev, port); 1442 port->handle_rx = console ? handle_rx_console : handle_rx_uart; 1443 1444 ret = uart_add_one_port(drv, uport); 1445 if (ret) 1446 return ret; 1447 1448 irq_set_status_flags(uport->irq, IRQ_NOAUTOEN); 1449 ret = devm_request_irq(uport->dev, uport->irq, qcom_geni_serial_isr, 1450 IRQF_TRIGGER_HIGH, port->name, uport); 1451 if (ret) { 1452 dev_err(uport->dev, "Failed to get IRQ ret %d\n", ret); 1453 uart_remove_one_port(drv, uport); 1454 return ret; 1455 } 1456 1457 /* 1458 * Set pm_runtime status as ACTIVE so that wakeup_irq gets 1459 * enabled/disabled from dev_pm_arm_wake_irq during system 1460 * suspend/resume respectively. 1461 */ 1462 pm_runtime_set_active(&pdev->dev); 1463 1464 if (port->wakeup_irq > 0) { 1465 device_init_wakeup(&pdev->dev, true); 1466 ret = dev_pm_set_dedicated_wake_irq(&pdev->dev, 1467 port->wakeup_irq); 1468 if (ret) { 1469 device_init_wakeup(&pdev->dev, false); 1470 uart_remove_one_port(drv, uport); 1471 return ret; 1472 } 1473 } 1474 1475 return 0; 1476 } 1477 1478 static int qcom_geni_serial_remove(struct platform_device *pdev) 1479 { 1480 struct qcom_geni_serial_port *port = platform_get_drvdata(pdev); 1481 struct uart_driver *drv = port->private_data.drv; 1482 1483 dev_pm_clear_wake_irq(&pdev->dev); 1484 device_init_wakeup(&pdev->dev, false); 1485 uart_remove_one_port(drv, &port->uport); 1486 1487 return 0; 1488 } 1489 1490 static int __maybe_unused qcom_geni_serial_sys_suspend(struct device *dev) 1491 { 1492 struct qcom_geni_serial_port *port = dev_get_drvdata(dev); 1493 struct uart_port *uport = &port->uport; 1494 struct qcom_geni_private_data *private_data = uport->private_data; 1495 1496 /* 1497 * This is done so we can hit the lowest possible state in suspend 1498 * even with no_console_suspend 1499 */ 1500 if (uart_console(uport)) { 1501 geni_icc_set_tag(&port->se, 0x3); 1502 geni_icc_set_bw(&port->se); 1503 } 1504 return uart_suspend_port(private_data->drv, uport); 1505 } 1506 1507 static int __maybe_unused qcom_geni_serial_sys_resume(struct device *dev) 1508 { 1509 int ret; 1510 struct qcom_geni_serial_port *port = dev_get_drvdata(dev); 1511 struct uart_port *uport = &port->uport; 1512 struct qcom_geni_private_data *private_data = uport->private_data; 1513 1514 ret = uart_resume_port(private_data->drv, uport); 1515 if (uart_console(uport)) { 1516 geni_icc_set_tag(&port->se, 0x7); 1517 geni_icc_set_bw(&port->se); 1518 } 1519 return ret; 1520 } 1521 1522 static const struct dev_pm_ops qcom_geni_serial_pm_ops = { 1523 SET_SYSTEM_SLEEP_PM_OPS(qcom_geni_serial_sys_suspend, 1524 qcom_geni_serial_sys_resume) 1525 }; 1526 1527 static const struct of_device_id qcom_geni_serial_match_table[] = { 1528 { .compatible = "qcom,geni-debug-uart", }, 1529 { .compatible = "qcom,geni-uart", }, 1530 {} 1531 }; 1532 MODULE_DEVICE_TABLE(of, qcom_geni_serial_match_table); 1533 1534 static struct platform_driver qcom_geni_serial_platform_driver = { 1535 .remove = qcom_geni_serial_remove, 1536 .probe = qcom_geni_serial_probe, 1537 .driver = { 1538 .name = "qcom_geni_serial", 1539 .of_match_table = qcom_geni_serial_match_table, 1540 .pm = &qcom_geni_serial_pm_ops, 1541 }, 1542 }; 1543 1544 static int __init qcom_geni_serial_init(void) 1545 { 1546 int ret; 1547 1548 ret = console_register(&qcom_geni_console_driver); 1549 if (ret) 1550 return ret; 1551 1552 ret = uart_register_driver(&qcom_geni_uart_driver); 1553 if (ret) { 1554 console_unregister(&qcom_geni_console_driver); 1555 return ret; 1556 } 1557 1558 ret = platform_driver_register(&qcom_geni_serial_platform_driver); 1559 if (ret) { 1560 console_unregister(&qcom_geni_console_driver); 1561 uart_unregister_driver(&qcom_geni_uart_driver); 1562 } 1563 return ret; 1564 } 1565 module_init(qcom_geni_serial_init); 1566 1567 static void __exit qcom_geni_serial_exit(void) 1568 { 1569 platform_driver_unregister(&qcom_geni_serial_platform_driver); 1570 console_unregister(&qcom_geni_console_driver); 1571 uart_unregister_driver(&qcom_geni_uart_driver); 1572 } 1573 module_exit(qcom_geni_serial_exit); 1574 1575 MODULE_DESCRIPTION("Serial driver for GENI based QUP cores"); 1576 MODULE_LICENSE("GPL v2"); 1577