1 /* SPDX-License-Identifier: GPL-2.0 */ 2 #ifndef __PMAC_ZILOG_H__ 3 #define __PMAC_ZILOG_H__ 4 5 /* 6 * At most 2 ESCCs with 2 ports each 7 */ 8 #define MAX_ZS_PORTS 4 9 10 /* 11 * We wrap our port structure around the generic uart_port. 12 */ 13 #define NUM_ZSREGS 17 14 15 struct uart_pmac_port { 16 struct uart_port port; 17 struct uart_pmac_port *mate; 18 19 #ifdef CONFIG_PPC_PMAC 20 /* macio_dev for the escc holding this port (maybe be null on 21 * early inited port) 22 */ 23 struct macio_dev *dev; 24 /* device node to this port, this points to one of 2 childs 25 * of "escc" node (ie. ch-a or ch-b) 26 */ 27 struct device_node *node; 28 #else 29 struct platform_device *pdev; 30 #endif 31 32 /* Port type as obtained from device tree (IRDA, modem, ...) */ 33 int port_type; 34 u8 curregs[NUM_ZSREGS]; 35 36 unsigned int flags; 37 #define PMACZILOG_FLAG_IS_CONS 0x00000001 38 #define PMACZILOG_FLAG_IS_KGDB 0x00000002 39 #define PMACZILOG_FLAG_MODEM_STATUS 0x00000004 40 #define PMACZILOG_FLAG_IS_CHANNEL_A 0x00000008 41 #define PMACZILOG_FLAG_REGS_HELD 0x00000010 42 #define PMACZILOG_FLAG_TX_STOPPED 0x00000020 43 #define PMACZILOG_FLAG_TX_ACTIVE 0x00000040 44 #define PMACZILOG_FLAG_IS_IRDA 0x00000100 45 #define PMACZILOG_FLAG_IS_INTMODEM 0x00000200 46 #define PMACZILOG_FLAG_HAS_DMA 0x00000400 47 #define PMACZILOG_FLAG_RSRC_REQUESTED 0x00000800 48 #define PMACZILOG_FLAG_IS_OPEN 0x00002000 49 #define PMACZILOG_FLAG_IS_EXTCLK 0x00008000 50 #define PMACZILOG_FLAG_BREAK 0x00010000 51 52 unsigned char parity_mask; 53 unsigned char prev_status; 54 55 volatile u8 __iomem *control_reg; 56 volatile u8 __iomem *data_reg; 57 58 #ifdef CONFIG_PPC_PMAC 59 unsigned int tx_dma_irq; 60 unsigned int rx_dma_irq; 61 volatile struct dbdma_regs __iomem *tx_dma_regs; 62 volatile struct dbdma_regs __iomem *rx_dma_regs; 63 #endif 64 65 unsigned char irq_name[8]; 66 67 struct ktermios termios_cache; 68 }; 69 70 #define to_pmz(p) ((struct uart_pmac_port *)(p)) 71 72 static inline struct uart_pmac_port *pmz_get_port_A(struct uart_pmac_port *uap) 73 { 74 if (uap->flags & PMACZILOG_FLAG_IS_CHANNEL_A) 75 return uap; 76 return uap->mate; 77 } 78 79 /* 80 * Register accessors. Note that we don't need to enforce a recovery 81 * delay on PCI PowerMac hardware, it's dealt in HW by the MacIO chip, 82 * though if we try to use this driver on older machines, we might have 83 * to add it back 84 */ 85 static inline u8 read_zsreg(struct uart_pmac_port *port, u8 reg) 86 { 87 if (reg != 0) 88 writeb(reg, port->control_reg); 89 return readb(port->control_reg); 90 } 91 92 static inline void write_zsreg(struct uart_pmac_port *port, u8 reg, u8 value) 93 { 94 if (reg != 0) 95 writeb(reg, port->control_reg); 96 writeb(value, port->control_reg); 97 } 98 99 static inline u8 read_zsdata(struct uart_pmac_port *port) 100 { 101 return readb(port->data_reg); 102 } 103 104 static inline void write_zsdata(struct uart_pmac_port *port, u8 data) 105 { 106 writeb(data, port->data_reg); 107 } 108 109 static inline void zssync(struct uart_pmac_port *port) 110 { 111 (void)readb(port->control_reg); 112 } 113 114 /* Conversion routines to/from brg time constants from/to bits 115 * per second. 116 */ 117 #define BRG_TO_BPS(brg, freq) ((freq) / 2 / ((brg) + 2)) 118 #define BPS_TO_BRG(bps, freq) ((((freq) + (bps)) / (2 * (bps))) - 2) 119 120 #define ZS_CLOCK 3686400 /* Z8530 RTxC input clock rate */ 121 122 /* The Zilog register set */ 123 124 #define FLAG 0x7e 125 126 /* Write Register 0 */ 127 #define R0 0 /* Register selects */ 128 #define R1 1 129 #define R2 2 130 #define R3 3 131 #define R4 4 132 #define R5 5 133 #define R6 6 134 #define R7 7 135 #define R8 8 136 #define R9 9 137 #define R10 10 138 #define R11 11 139 #define R12 12 140 #define R13 13 141 #define R14 14 142 #define R15 15 143 #define R7P 16 144 145 #define NULLCODE 0 /* Null Code */ 146 #define POINT_HIGH 0x8 /* Select upper half of registers */ 147 #define RES_EXT_INT 0x10 /* Reset Ext. Status Interrupts */ 148 #define SEND_ABORT 0x18 /* HDLC Abort */ 149 #define RES_RxINT_FC 0x20 /* Reset RxINT on First Character */ 150 #define RES_Tx_P 0x28 /* Reset TxINT Pending */ 151 #define ERR_RES 0x30 /* Error Reset */ 152 #define RES_H_IUS 0x38 /* Reset highest IUS */ 153 154 #define RES_Rx_CRC 0x40 /* Reset Rx CRC Checker */ 155 #define RES_Tx_CRC 0x80 /* Reset Tx CRC Checker */ 156 #define RES_EOM_L 0xC0 /* Reset EOM latch */ 157 158 /* Write Register 1 */ 159 160 #define EXT_INT_ENAB 0x1 /* Ext Int Enable */ 161 #define TxINT_ENAB 0x2 /* Tx Int Enable */ 162 #define PAR_SPEC 0x4 /* Parity is special condition */ 163 164 #define RxINT_DISAB 0 /* Rx Int Disable */ 165 #define RxINT_FCERR 0x8 /* Rx Int on First Character Only or Error */ 166 #define INT_ALL_Rx 0x10 /* Int on all Rx Characters or error */ 167 #define INT_ERR_Rx 0x18 /* Int on error only */ 168 #define RxINT_MASK 0x18 169 170 #define WT_RDY_RT 0x20 /* W/Req reflects recv if 1, xmit if 0 */ 171 #define WT_FN_RDYFN 0x40 /* W/Req pin is DMA request if 1, wait if 0 */ 172 #define WT_RDY_ENAB 0x80 /* Enable W/Req pin */ 173 174 /* Write Register #2 (Interrupt Vector) */ 175 176 /* Write Register 3 */ 177 178 #define RxENABLE 0x1 /* Rx Enable */ 179 #define SYNC_L_INH 0x2 /* Sync Character Load Inhibit */ 180 #define ADD_SM 0x4 /* Address Search Mode (SDLC) */ 181 #define RxCRC_ENAB 0x8 /* Rx CRC Enable */ 182 #define ENT_HM 0x10 /* Enter Hunt Mode */ 183 #define AUTO_ENAB 0x20 /* Auto Enables */ 184 #define Rx5 0x0 /* Rx 5 Bits/Character */ 185 #define Rx7 0x40 /* Rx 7 Bits/Character */ 186 #define Rx6 0x80 /* Rx 6 Bits/Character */ 187 #define Rx8 0xc0 /* Rx 8 Bits/Character */ 188 #define RxN_MASK 0xc0 189 190 /* Write Register 4 */ 191 192 #define PAR_ENAB 0x1 /* Parity Enable */ 193 #define PAR_EVEN 0x2 /* Parity Even/Odd* */ 194 195 #define SYNC_ENAB 0 /* Sync Modes Enable */ 196 #define SB1 0x4 /* 1 stop bit/char */ 197 #define SB15 0x8 /* 1.5 stop bits/char */ 198 #define SB2 0xc /* 2 stop bits/char */ 199 #define SB_MASK 0xc 200 201 #define MONSYNC 0 /* 8 Bit Sync character */ 202 #define BISYNC 0x10 /* 16 bit sync character */ 203 #define SDLC 0x20 /* SDLC Mode (01111110 Sync Flag) */ 204 #define EXTSYNC 0x30 /* External Sync Mode */ 205 206 #define X1CLK 0x0 /* x1 clock mode */ 207 #define X16CLK 0x40 /* x16 clock mode */ 208 #define X32CLK 0x80 /* x32 clock mode */ 209 #define X64CLK 0xC0 /* x64 clock mode */ 210 #define XCLK_MASK 0xC0 211 212 /* Write Register 5 */ 213 214 #define TxCRC_ENAB 0x1 /* Tx CRC Enable */ 215 #define RTS 0x2 /* RTS */ 216 #define SDLC_CRC 0x4 /* SDLC/CRC-16 */ 217 #define TxENABLE 0x8 /* Tx Enable */ 218 #define SND_BRK 0x10 /* Send Break */ 219 #define Tx5 0x0 /* Tx 5 bits (or less)/character */ 220 #define Tx7 0x20 /* Tx 7 bits/character */ 221 #define Tx6 0x40 /* Tx 6 bits/character */ 222 #define Tx8 0x60 /* Tx 8 bits/character */ 223 #define TxN_MASK 0x60 224 #define DTR 0x80 /* DTR */ 225 226 /* Write Register 6 (Sync bits 0-7/SDLC Address Field) */ 227 228 /* Write Register 7 (Sync bits 8-15/SDLC 01111110) */ 229 230 /* Write Register 7' (Some enhanced feature control) */ 231 #define ENEXREAD 0x40 /* Enable read of some write registers */ 232 233 /* Write Register 8 (transmit buffer) */ 234 235 /* Write Register 9 (Master interrupt control) */ 236 #define VIS 1 /* Vector Includes Status */ 237 #define NV 2 /* No Vector */ 238 #define DLC 4 /* Disable Lower Chain */ 239 #define MIE 8 /* Master Interrupt Enable */ 240 #define STATHI 0x10 /* Status high */ 241 #define NORESET 0 /* No reset on write to R9 */ 242 #define CHRB 0x40 /* Reset channel B */ 243 #define CHRA 0x80 /* Reset channel A */ 244 #define FHWRES 0xc0 /* Force hardware reset */ 245 246 /* Write Register 10 (misc control bits) */ 247 #define BIT6 1 /* 6 bit/8bit sync */ 248 #define LOOPMODE 2 /* SDLC Loop mode */ 249 #define ABUNDER 4 /* Abort/flag on SDLC xmit underrun */ 250 #define MARKIDLE 8 /* Mark/flag on idle */ 251 #define GAOP 0x10 /* Go active on poll */ 252 #define NRZ 0 /* NRZ mode */ 253 #define NRZI 0x20 /* NRZI mode */ 254 #define FM1 0x40 /* FM1 (transition = 1) */ 255 #define FM0 0x60 /* FM0 (transition = 0) */ 256 #define CRCPS 0x80 /* CRC Preset I/O */ 257 258 /* Write Register 11 (Clock Mode control) */ 259 #define TRxCXT 0 /* TRxC = Xtal output */ 260 #define TRxCTC 1 /* TRxC = Transmit clock */ 261 #define TRxCBR 2 /* TRxC = BR Generator Output */ 262 #define TRxCDP 3 /* TRxC = DPLL output */ 263 #define TRxCOI 4 /* TRxC O/I */ 264 #define TCRTxCP 0 /* Transmit clock = RTxC pin */ 265 #define TCTRxCP 8 /* Transmit clock = TRxC pin */ 266 #define TCBR 0x10 /* Transmit clock = BR Generator output */ 267 #define TCDPLL 0x18 /* Transmit clock = DPLL output */ 268 #define RCRTxCP 0 /* Receive clock = RTxC pin */ 269 #define RCTRxCP 0x20 /* Receive clock = TRxC pin */ 270 #define RCBR 0x40 /* Receive clock = BR Generator output */ 271 #define RCDPLL 0x60 /* Receive clock = DPLL output */ 272 #define RTxCX 0x80 /* RTxC Xtal/No Xtal */ 273 274 /* Write Register 12 (lower byte of baud rate generator time constant) */ 275 276 /* Write Register 13 (upper byte of baud rate generator time constant) */ 277 278 /* Write Register 14 (Misc control bits) */ 279 #define BRENAB 1 /* Baud rate generator enable */ 280 #define BRSRC 2 /* Baud rate generator source */ 281 #define DTRREQ 4 /* DTR/Request function */ 282 #define AUTOECHO 8 /* Auto Echo */ 283 #define LOOPBAK 0x10 /* Local loopback */ 284 #define SEARCH 0x20 /* Enter search mode */ 285 #define RMC 0x40 /* Reset missing clock */ 286 #define DISDPLL 0x60 /* Disable DPLL */ 287 #define SSBR 0x80 /* Set DPLL source = BR generator */ 288 #define SSRTxC 0xa0 /* Set DPLL source = RTxC */ 289 #define SFMM 0xc0 /* Set FM mode */ 290 #define SNRZI 0xe0 /* Set NRZI mode */ 291 292 /* Write Register 15 (external/status interrupt control) */ 293 #define EN85C30 1 /* Enable some 85c30-enhanced registers */ 294 #define ZCIE 2 /* Zero count IE */ 295 #define ENSTFIFO 4 /* Enable status FIFO (SDLC) */ 296 #define DCDIE 8 /* DCD IE */ 297 #define SYNCIE 0x10 /* Sync/hunt IE */ 298 #define CTSIE 0x20 /* CTS IE */ 299 #define TxUIE 0x40 /* Tx Underrun/EOM IE */ 300 #define BRKIE 0x80 /* Break/Abort IE */ 301 302 303 /* Read Register 0 */ 304 #define Rx_CH_AV 0x1 /* Rx Character Available */ 305 #define ZCOUNT 0x2 /* Zero count */ 306 #define Tx_BUF_EMP 0x4 /* Tx Buffer empty */ 307 #define DCD 0x8 /* DCD */ 308 #define SYNC_HUNT 0x10 /* Sync/hunt */ 309 #define CTS 0x20 /* CTS */ 310 #define TxEOM 0x40 /* Tx underrun */ 311 #define BRK_ABRT 0x80 /* Break/Abort */ 312 313 /* Read Register 1 */ 314 #define ALL_SNT 0x1 /* All sent */ 315 /* Residue Data for 8 Rx bits/char programmed */ 316 #define RES3 0x8 /* 0/3 */ 317 #define RES4 0x4 /* 0/4 */ 318 #define RES5 0xc /* 0/5 */ 319 #define RES6 0x2 /* 0/6 */ 320 #define RES7 0xa /* 0/7 */ 321 #define RES8 0x6 /* 0/8 */ 322 #define RES18 0xe /* 1/8 */ 323 #define RES28 0x0 /* 2/8 */ 324 /* Special Rx Condition Interrupts */ 325 #define PAR_ERR 0x10 /* Parity error */ 326 #define Rx_OVR 0x20 /* Rx Overrun Error */ 327 #define CRC_ERR 0x40 /* CRC/Framing Error */ 328 #define END_FR 0x80 /* End of Frame (SDLC) */ 329 330 /* Read Register 2 (channel b only) - Interrupt vector */ 331 #define CHB_Tx_EMPTY 0x00 332 #define CHB_EXT_STAT 0x02 333 #define CHB_Rx_AVAIL 0x04 334 #define CHB_SPECIAL 0x06 335 #define CHA_Tx_EMPTY 0x08 336 #define CHA_EXT_STAT 0x0a 337 #define CHA_Rx_AVAIL 0x0c 338 #define CHA_SPECIAL 0x0e 339 #define STATUS_MASK 0x06 340 341 /* Read Register 3 (interrupt pending register) ch a only */ 342 #define CHBEXT 0x1 /* Channel B Ext/Stat IP */ 343 #define CHBTxIP 0x2 /* Channel B Tx IP */ 344 #define CHBRxIP 0x4 /* Channel B Rx IP */ 345 #define CHAEXT 0x8 /* Channel A Ext/Stat IP */ 346 #define CHATxIP 0x10 /* Channel A Tx IP */ 347 #define CHARxIP 0x20 /* Channel A Rx IP */ 348 349 /* Read Register 8 (receive data register) */ 350 351 /* Read Register 10 (misc status bits) */ 352 #define ONLOOP 2 /* On loop */ 353 #define LOOPSEND 0x10 /* Loop sending */ 354 #define CLK2MIS 0x40 /* Two clocks missing */ 355 #define CLK1MIS 0x80 /* One clock missing */ 356 357 /* Read Register 12 (lower byte of baud rate generator constant) */ 358 359 /* Read Register 13 (upper byte of baud rate generator constant) */ 360 361 /* Read Register 15 (value of WR 15) */ 362 363 /* Misc macros */ 364 #define ZS_CLEARERR(port) (write_zsreg(port, 0, ERR_RES)) 365 #define ZS_CLEARFIFO(port) do { \ 366 read_zsdata(port); \ 367 read_zsdata(port); \ 368 read_zsdata(port); \ 369 } while(0) 370 371 #define ZS_IS_CONS(UP) ((UP)->flags & PMACZILOG_FLAG_IS_CONS) 372 #define ZS_IS_KGDB(UP) ((UP)->flags & PMACZILOG_FLAG_IS_KGDB) 373 #define ZS_IS_CHANNEL_A(UP) ((UP)->flags & PMACZILOG_FLAG_IS_CHANNEL_A) 374 #define ZS_REGS_HELD(UP) ((UP)->flags & PMACZILOG_FLAG_REGS_HELD) 375 #define ZS_TX_STOPPED(UP) ((UP)->flags & PMACZILOG_FLAG_TX_STOPPED) 376 #define ZS_TX_ACTIVE(UP) ((UP)->flags & PMACZILOG_FLAG_TX_ACTIVE) 377 #define ZS_WANTS_MODEM_STATUS(UP) ((UP)->flags & PMACZILOG_FLAG_MODEM_STATUS) 378 #define ZS_IS_IRDA(UP) ((UP)->flags & PMACZILOG_FLAG_IS_IRDA) 379 #define ZS_IS_INTMODEM(UP) ((UP)->flags & PMACZILOG_FLAG_IS_INTMODEM) 380 #define ZS_HAS_DMA(UP) ((UP)->flags & PMACZILOG_FLAG_HAS_DMA) 381 #define ZS_IS_OPEN(UP) ((UP)->flags & PMACZILOG_FLAG_IS_OPEN) 382 #define ZS_IS_EXTCLK(UP) ((UP)->flags & PMACZILOG_FLAG_IS_EXTCLK) 383 384 #endif /* __PMAC_ZILOG_H__ */ 385