1 /* 2 * Driver for PowerMac Z85c30 based ESCC cell found in the 3 * "macio" ASICs of various PowerMac models 4 * 5 * Copyright (C) 2003 Ben. Herrenschmidt (benh@kernel.crashing.org) 6 * 7 * Derived from drivers/macintosh/macserial.c by Paul Mackerras 8 * and drivers/serial/sunzilog.c by David S. Miller 9 * 10 * Hrm... actually, I ripped most of sunzilog (Thanks David !) and 11 * adapted special tweaks needed for us. I don't think it's worth 12 * merging back those though. The DMA code still has to get in 13 * and once done, I expect that driver to remain fairly stable in 14 * the long term, unless we change the driver model again... 15 * 16 * This program is free software; you can redistribute it and/or modify 17 * it under the terms of the GNU General Public License as published by 18 * the Free Software Foundation; either version 2 of the License, or 19 * (at your option) any later version. 20 * 21 * This program is distributed in the hope that it will be useful, 22 * but WITHOUT ANY WARRANTY; without even the implied warranty of 23 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the 24 * GNU General Public License for more details. 25 * 26 * You should have received a copy of the GNU General Public License 27 * along with this program; if not, write to the Free Software 28 * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA 29 * 30 * 2004-08-06 Harald Welte <laforge@gnumonks.org> 31 * - Enable BREAK interrupt 32 * - Add support for sysreq 33 * 34 * TODO: - Add DMA support 35 * - Defer port shutdown to a few seconds after close 36 * - maybe put something right into uap->clk_divisor 37 */ 38 39 #undef DEBUG 40 #undef DEBUG_HARD 41 #undef USE_CTRL_O_SYSRQ 42 43 #include <linux/module.h> 44 #include <linux/tty.h> 45 46 #include <linux/tty_flip.h> 47 #include <linux/major.h> 48 #include <linux/string.h> 49 #include <linux/fcntl.h> 50 #include <linux/mm.h> 51 #include <linux/kernel.h> 52 #include <linux/delay.h> 53 #include <linux/init.h> 54 #include <linux/console.h> 55 #include <linux/adb.h> 56 #include <linux/pmu.h> 57 #include <linux/bitops.h> 58 #include <linux/sysrq.h> 59 #include <linux/mutex.h> 60 #include <linux/of_address.h> 61 #include <linux/of_irq.h> 62 #include <asm/sections.h> 63 #include <asm/io.h> 64 #include <asm/irq.h> 65 66 #ifdef CONFIG_PPC_PMAC 67 #include <asm/prom.h> 68 #include <asm/machdep.h> 69 #include <asm/pmac_feature.h> 70 #include <asm/dbdma.h> 71 #include <asm/macio.h> 72 #else 73 #include <linux/platform_device.h> 74 #define of_machine_is_compatible(x) (0) 75 #endif 76 77 #if defined (CONFIG_SERIAL_PMACZILOG_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ) 78 #define SUPPORT_SYSRQ 79 #endif 80 81 #include <linux/serial.h> 82 #include <linux/serial_core.h> 83 84 #include "pmac_zilog.h" 85 86 /* Not yet implemented */ 87 #undef HAS_DBDMA 88 89 static char version[] __initdata = "pmac_zilog: 0.6 (Benjamin Herrenschmidt <benh@kernel.crashing.org>)"; 90 MODULE_AUTHOR("Benjamin Herrenschmidt <benh@kernel.crashing.org>"); 91 MODULE_DESCRIPTION("Driver for the Mac and PowerMac serial ports."); 92 MODULE_LICENSE("GPL"); 93 94 #ifdef CONFIG_SERIAL_PMACZILOG_TTYS 95 #define PMACZILOG_MAJOR TTY_MAJOR 96 #define PMACZILOG_MINOR 64 97 #define PMACZILOG_NAME "ttyS" 98 #else 99 #define PMACZILOG_MAJOR 204 100 #define PMACZILOG_MINOR 192 101 #define PMACZILOG_NAME "ttyPZ" 102 #endif 103 104 #define pmz_debug(fmt, arg...) pr_debug("ttyPZ%d: " fmt, uap->port.line, ## arg) 105 #define pmz_error(fmt, arg...) pr_err("ttyPZ%d: " fmt, uap->port.line, ## arg) 106 #define pmz_info(fmt, arg...) pr_info("ttyPZ%d: " fmt, uap->port.line, ## arg) 107 108 /* 109 * For the sake of early serial console, we can do a pre-probe 110 * (optional) of the ports at rather early boot time. 111 */ 112 static struct uart_pmac_port pmz_ports[MAX_ZS_PORTS]; 113 static int pmz_ports_count; 114 115 static struct uart_driver pmz_uart_reg = { 116 .owner = THIS_MODULE, 117 .driver_name = PMACZILOG_NAME, 118 .dev_name = PMACZILOG_NAME, 119 .major = PMACZILOG_MAJOR, 120 .minor = PMACZILOG_MINOR, 121 }; 122 123 124 /* 125 * Load all registers to reprogram the port 126 * This function must only be called when the TX is not busy. The UART 127 * port lock must be held and local interrupts disabled. 128 */ 129 static void pmz_load_zsregs(struct uart_pmac_port *uap, u8 *regs) 130 { 131 int i; 132 133 /* Let pending transmits finish. */ 134 for (i = 0; i < 1000; i++) { 135 unsigned char stat = read_zsreg(uap, R1); 136 if (stat & ALL_SNT) 137 break; 138 udelay(100); 139 } 140 141 ZS_CLEARERR(uap); 142 zssync(uap); 143 ZS_CLEARFIFO(uap); 144 zssync(uap); 145 ZS_CLEARERR(uap); 146 147 /* Disable all interrupts. */ 148 write_zsreg(uap, R1, 149 regs[R1] & ~(RxINT_MASK | TxINT_ENAB | EXT_INT_ENAB)); 150 151 /* Set parity, sync config, stop bits, and clock divisor. */ 152 write_zsreg(uap, R4, regs[R4]); 153 154 /* Set misc. TX/RX control bits. */ 155 write_zsreg(uap, R10, regs[R10]); 156 157 /* Set TX/RX controls sans the enable bits. */ 158 write_zsreg(uap, R3, regs[R3] & ~RxENABLE); 159 write_zsreg(uap, R5, regs[R5] & ~TxENABLE); 160 161 /* now set R7 "prime" on ESCC */ 162 write_zsreg(uap, R15, regs[R15] | EN85C30); 163 write_zsreg(uap, R7, regs[R7P]); 164 165 /* make sure we use R7 "non-prime" on ESCC */ 166 write_zsreg(uap, R15, regs[R15] & ~EN85C30); 167 168 /* Synchronous mode config. */ 169 write_zsreg(uap, R6, regs[R6]); 170 write_zsreg(uap, R7, regs[R7]); 171 172 /* Disable baud generator. */ 173 write_zsreg(uap, R14, regs[R14] & ~BRENAB); 174 175 /* Clock mode control. */ 176 write_zsreg(uap, R11, regs[R11]); 177 178 /* Lower and upper byte of baud rate generator divisor. */ 179 write_zsreg(uap, R12, regs[R12]); 180 write_zsreg(uap, R13, regs[R13]); 181 182 /* Now rewrite R14, with BRENAB (if set). */ 183 write_zsreg(uap, R14, regs[R14]); 184 185 /* Reset external status interrupts. */ 186 write_zsreg(uap, R0, RES_EXT_INT); 187 write_zsreg(uap, R0, RES_EXT_INT); 188 189 /* Rewrite R3/R5, this time without enables masked. */ 190 write_zsreg(uap, R3, regs[R3]); 191 write_zsreg(uap, R5, regs[R5]); 192 193 /* Rewrite R1, this time without IRQ enabled masked. */ 194 write_zsreg(uap, R1, regs[R1]); 195 196 /* Enable interrupts */ 197 write_zsreg(uap, R9, regs[R9]); 198 } 199 200 /* 201 * We do like sunzilog to avoid disrupting pending Tx 202 * Reprogram the Zilog channel HW registers with the copies found in the 203 * software state struct. If the transmitter is busy, we defer this update 204 * until the next TX complete interrupt. Else, we do it right now. 205 * 206 * The UART port lock must be held and local interrupts disabled. 207 */ 208 static void pmz_maybe_update_regs(struct uart_pmac_port *uap) 209 { 210 if (!ZS_REGS_HELD(uap)) { 211 if (ZS_TX_ACTIVE(uap)) { 212 uap->flags |= PMACZILOG_FLAG_REGS_HELD; 213 } else { 214 pmz_debug("pmz: maybe_update_regs: updating\n"); 215 pmz_load_zsregs(uap, uap->curregs); 216 } 217 } 218 } 219 220 static void pmz_interrupt_control(struct uart_pmac_port *uap, int enable) 221 { 222 if (enable) { 223 uap->curregs[1] |= INT_ALL_Rx | TxINT_ENAB; 224 if (!ZS_IS_EXTCLK(uap)) 225 uap->curregs[1] |= EXT_INT_ENAB; 226 } else { 227 uap->curregs[1] &= ~(EXT_INT_ENAB | TxINT_ENAB | RxINT_MASK); 228 } 229 write_zsreg(uap, R1, uap->curregs[1]); 230 } 231 232 static bool pmz_receive_chars(struct uart_pmac_port *uap) 233 { 234 struct tty_port *port; 235 unsigned char ch, r1, drop, error, flag; 236 int loops = 0; 237 238 /* Sanity check, make sure the old bug is no longer happening */ 239 if (uap->port.state == NULL) { 240 WARN_ON(1); 241 (void)read_zsdata(uap); 242 return false; 243 } 244 port = &uap->port.state->port; 245 246 while (1) { 247 error = 0; 248 drop = 0; 249 250 r1 = read_zsreg(uap, R1); 251 ch = read_zsdata(uap); 252 253 if (r1 & (PAR_ERR | Rx_OVR | CRC_ERR)) { 254 write_zsreg(uap, R0, ERR_RES); 255 zssync(uap); 256 } 257 258 ch &= uap->parity_mask; 259 if (ch == 0 && uap->flags & PMACZILOG_FLAG_BREAK) { 260 uap->flags &= ~PMACZILOG_FLAG_BREAK; 261 } 262 263 #if defined(CONFIG_MAGIC_SYSRQ) && defined(CONFIG_SERIAL_CORE_CONSOLE) 264 #ifdef USE_CTRL_O_SYSRQ 265 /* Handle the SysRq ^O Hack */ 266 if (ch == '\x0f') { 267 uap->port.sysrq = jiffies + HZ*5; 268 goto next_char; 269 } 270 #endif /* USE_CTRL_O_SYSRQ */ 271 if (uap->port.sysrq) { 272 int swallow; 273 spin_unlock(&uap->port.lock); 274 swallow = uart_handle_sysrq_char(&uap->port, ch); 275 spin_lock(&uap->port.lock); 276 if (swallow) 277 goto next_char; 278 } 279 #endif /* CONFIG_MAGIC_SYSRQ && CONFIG_SERIAL_CORE_CONSOLE */ 280 281 /* A real serial line, record the character and status. */ 282 if (drop) 283 goto next_char; 284 285 flag = TTY_NORMAL; 286 uap->port.icount.rx++; 287 288 if (r1 & (PAR_ERR | Rx_OVR | CRC_ERR | BRK_ABRT)) { 289 error = 1; 290 if (r1 & BRK_ABRT) { 291 pmz_debug("pmz: got break !\n"); 292 r1 &= ~(PAR_ERR | CRC_ERR); 293 uap->port.icount.brk++; 294 if (uart_handle_break(&uap->port)) 295 goto next_char; 296 } 297 else if (r1 & PAR_ERR) 298 uap->port.icount.parity++; 299 else if (r1 & CRC_ERR) 300 uap->port.icount.frame++; 301 if (r1 & Rx_OVR) 302 uap->port.icount.overrun++; 303 r1 &= uap->port.read_status_mask; 304 if (r1 & BRK_ABRT) 305 flag = TTY_BREAK; 306 else if (r1 & PAR_ERR) 307 flag = TTY_PARITY; 308 else if (r1 & CRC_ERR) 309 flag = TTY_FRAME; 310 } 311 312 if (uap->port.ignore_status_mask == 0xff || 313 (r1 & uap->port.ignore_status_mask) == 0) { 314 tty_insert_flip_char(port, ch, flag); 315 } 316 if (r1 & Rx_OVR) 317 tty_insert_flip_char(port, 0, TTY_OVERRUN); 318 next_char: 319 /* We can get stuck in an infinite loop getting char 0 when the 320 * line is in a wrong HW state, we break that here. 321 * When that happens, I disable the receive side of the driver. 322 * Note that what I've been experiencing is a real irq loop where 323 * I'm getting flooded regardless of the actual port speed. 324 * Something strange is going on with the HW 325 */ 326 if ((++loops) > 1000) 327 goto flood; 328 ch = read_zsreg(uap, R0); 329 if (!(ch & Rx_CH_AV)) 330 break; 331 } 332 333 return true; 334 flood: 335 pmz_interrupt_control(uap, 0); 336 pmz_error("pmz: rx irq flood !\n"); 337 return true; 338 } 339 340 static void pmz_status_handle(struct uart_pmac_port *uap) 341 { 342 unsigned char status; 343 344 status = read_zsreg(uap, R0); 345 write_zsreg(uap, R0, RES_EXT_INT); 346 zssync(uap); 347 348 if (ZS_IS_OPEN(uap) && ZS_WANTS_MODEM_STATUS(uap)) { 349 if (status & SYNC_HUNT) 350 uap->port.icount.dsr++; 351 352 /* The Zilog just gives us an interrupt when DCD/CTS/etc. change. 353 * But it does not tell us which bit has changed, we have to keep 354 * track of this ourselves. 355 * The CTS input is inverted for some reason. -- paulus 356 */ 357 if ((status ^ uap->prev_status) & DCD) 358 uart_handle_dcd_change(&uap->port, 359 (status & DCD)); 360 if ((status ^ uap->prev_status) & CTS) 361 uart_handle_cts_change(&uap->port, 362 !(status & CTS)); 363 364 wake_up_interruptible(&uap->port.state->port.delta_msr_wait); 365 } 366 367 if (status & BRK_ABRT) 368 uap->flags |= PMACZILOG_FLAG_BREAK; 369 370 uap->prev_status = status; 371 } 372 373 static void pmz_transmit_chars(struct uart_pmac_port *uap) 374 { 375 struct circ_buf *xmit; 376 377 if (ZS_IS_CONS(uap)) { 378 unsigned char status = read_zsreg(uap, R0); 379 380 /* TX still busy? Just wait for the next TX done interrupt. 381 * 382 * It can occur because of how we do serial console writes. It would 383 * be nice to transmit console writes just like we normally would for 384 * a TTY line. (ie. buffered and TX interrupt driven). That is not 385 * easy because console writes cannot sleep. One solution might be 386 * to poll on enough port->xmit space becoming free. -DaveM 387 */ 388 if (!(status & Tx_BUF_EMP)) 389 return; 390 } 391 392 uap->flags &= ~PMACZILOG_FLAG_TX_ACTIVE; 393 394 if (ZS_REGS_HELD(uap)) { 395 pmz_load_zsregs(uap, uap->curregs); 396 uap->flags &= ~PMACZILOG_FLAG_REGS_HELD; 397 } 398 399 if (ZS_TX_STOPPED(uap)) { 400 uap->flags &= ~PMACZILOG_FLAG_TX_STOPPED; 401 goto ack_tx_int; 402 } 403 404 /* Under some circumstances, we see interrupts reported for 405 * a closed channel. The interrupt mask in R1 is clear, but 406 * R3 still signals the interrupts and we see them when taking 407 * an interrupt for the other channel (this could be a qemu 408 * bug but since the ESCC doc doesn't specify precsiely whether 409 * R3 interrup status bits are masked by R1 interrupt enable 410 * bits, better safe than sorry). --BenH. 411 */ 412 if (!ZS_IS_OPEN(uap)) 413 goto ack_tx_int; 414 415 if (uap->port.x_char) { 416 uap->flags |= PMACZILOG_FLAG_TX_ACTIVE; 417 write_zsdata(uap, uap->port.x_char); 418 zssync(uap); 419 uap->port.icount.tx++; 420 uap->port.x_char = 0; 421 return; 422 } 423 424 if (uap->port.state == NULL) 425 goto ack_tx_int; 426 xmit = &uap->port.state->xmit; 427 if (uart_circ_empty(xmit)) { 428 uart_write_wakeup(&uap->port); 429 goto ack_tx_int; 430 } 431 if (uart_tx_stopped(&uap->port)) 432 goto ack_tx_int; 433 434 uap->flags |= PMACZILOG_FLAG_TX_ACTIVE; 435 write_zsdata(uap, xmit->buf[xmit->tail]); 436 zssync(uap); 437 438 xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1); 439 uap->port.icount.tx++; 440 441 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) 442 uart_write_wakeup(&uap->port); 443 444 return; 445 446 ack_tx_int: 447 write_zsreg(uap, R0, RES_Tx_P); 448 zssync(uap); 449 } 450 451 /* Hrm... we register that twice, fixme later.... */ 452 static irqreturn_t pmz_interrupt(int irq, void *dev_id) 453 { 454 struct uart_pmac_port *uap = dev_id; 455 struct uart_pmac_port *uap_a; 456 struct uart_pmac_port *uap_b; 457 int rc = IRQ_NONE; 458 bool push; 459 u8 r3; 460 461 uap_a = pmz_get_port_A(uap); 462 uap_b = uap_a->mate; 463 464 spin_lock(&uap_a->port.lock); 465 r3 = read_zsreg(uap_a, R3); 466 467 #ifdef DEBUG_HARD 468 pmz_debug("irq, r3: %x\n", r3); 469 #endif 470 /* Channel A */ 471 push = false; 472 if (r3 & (CHAEXT | CHATxIP | CHARxIP)) { 473 if (!ZS_IS_OPEN(uap_a)) { 474 pmz_debug("ChanA interrupt while not open !\n"); 475 goto skip_a; 476 } 477 write_zsreg(uap_a, R0, RES_H_IUS); 478 zssync(uap_a); 479 if (r3 & CHAEXT) 480 pmz_status_handle(uap_a); 481 if (r3 & CHARxIP) 482 push = pmz_receive_chars(uap_a); 483 if (r3 & CHATxIP) 484 pmz_transmit_chars(uap_a); 485 rc = IRQ_HANDLED; 486 } 487 skip_a: 488 spin_unlock(&uap_a->port.lock); 489 if (push) 490 tty_flip_buffer_push(&uap->port.state->port); 491 492 if (!uap_b) 493 goto out; 494 495 spin_lock(&uap_b->port.lock); 496 push = false; 497 if (r3 & (CHBEXT | CHBTxIP | CHBRxIP)) { 498 if (!ZS_IS_OPEN(uap_b)) { 499 pmz_debug("ChanB interrupt while not open !\n"); 500 goto skip_b; 501 } 502 write_zsreg(uap_b, R0, RES_H_IUS); 503 zssync(uap_b); 504 if (r3 & CHBEXT) 505 pmz_status_handle(uap_b); 506 if (r3 & CHBRxIP) 507 push = pmz_receive_chars(uap_b); 508 if (r3 & CHBTxIP) 509 pmz_transmit_chars(uap_b); 510 rc = IRQ_HANDLED; 511 } 512 skip_b: 513 spin_unlock(&uap_b->port.lock); 514 if (push) 515 tty_flip_buffer_push(&uap->port.state->port); 516 517 out: 518 return rc; 519 } 520 521 /* 522 * Peek the status register, lock not held by caller 523 */ 524 static inline u8 pmz_peek_status(struct uart_pmac_port *uap) 525 { 526 unsigned long flags; 527 u8 status; 528 529 spin_lock_irqsave(&uap->port.lock, flags); 530 status = read_zsreg(uap, R0); 531 spin_unlock_irqrestore(&uap->port.lock, flags); 532 533 return status; 534 } 535 536 /* 537 * Check if transmitter is empty 538 * The port lock is not held. 539 */ 540 static unsigned int pmz_tx_empty(struct uart_port *port) 541 { 542 unsigned char status; 543 544 status = pmz_peek_status(to_pmz(port)); 545 if (status & Tx_BUF_EMP) 546 return TIOCSER_TEMT; 547 return 0; 548 } 549 550 /* 551 * Set Modem Control (RTS & DTR) bits 552 * The port lock is held and interrupts are disabled. 553 * Note: Shall we really filter out RTS on external ports or 554 * should that be dealt at higher level only ? 555 */ 556 static void pmz_set_mctrl(struct uart_port *port, unsigned int mctrl) 557 { 558 struct uart_pmac_port *uap = to_pmz(port); 559 unsigned char set_bits, clear_bits; 560 561 /* Do nothing for irda for now... */ 562 if (ZS_IS_IRDA(uap)) 563 return; 564 /* We get called during boot with a port not up yet */ 565 if (!(ZS_IS_OPEN(uap) || ZS_IS_CONS(uap))) 566 return; 567 568 set_bits = clear_bits = 0; 569 570 if (ZS_IS_INTMODEM(uap)) { 571 if (mctrl & TIOCM_RTS) 572 set_bits |= RTS; 573 else 574 clear_bits |= RTS; 575 } 576 if (mctrl & TIOCM_DTR) 577 set_bits |= DTR; 578 else 579 clear_bits |= DTR; 580 581 /* NOTE: Not subject to 'transmitter active' rule. */ 582 uap->curregs[R5] |= set_bits; 583 uap->curregs[R5] &= ~clear_bits; 584 585 write_zsreg(uap, R5, uap->curregs[R5]); 586 pmz_debug("pmz_set_mctrl: set bits: %x, clear bits: %x -> %x\n", 587 set_bits, clear_bits, uap->curregs[R5]); 588 zssync(uap); 589 } 590 591 /* 592 * Get Modem Control bits (only the input ones, the core will 593 * or that with a cached value of the control ones) 594 * The port lock is held and interrupts are disabled. 595 */ 596 static unsigned int pmz_get_mctrl(struct uart_port *port) 597 { 598 struct uart_pmac_port *uap = to_pmz(port); 599 unsigned char status; 600 unsigned int ret; 601 602 status = read_zsreg(uap, R0); 603 604 ret = 0; 605 if (status & DCD) 606 ret |= TIOCM_CAR; 607 if (status & SYNC_HUNT) 608 ret |= TIOCM_DSR; 609 if (!(status & CTS)) 610 ret |= TIOCM_CTS; 611 612 return ret; 613 } 614 615 /* 616 * Stop TX side. Dealt like sunzilog at next Tx interrupt, 617 * though for DMA, we will have to do a bit more. 618 * The port lock is held and interrupts are disabled. 619 */ 620 static void pmz_stop_tx(struct uart_port *port) 621 { 622 to_pmz(port)->flags |= PMACZILOG_FLAG_TX_STOPPED; 623 } 624 625 /* 626 * Kick the Tx side. 627 * The port lock is held and interrupts are disabled. 628 */ 629 static void pmz_start_tx(struct uart_port *port) 630 { 631 struct uart_pmac_port *uap = to_pmz(port); 632 unsigned char status; 633 634 pmz_debug("pmz: start_tx()\n"); 635 636 uap->flags |= PMACZILOG_FLAG_TX_ACTIVE; 637 uap->flags &= ~PMACZILOG_FLAG_TX_STOPPED; 638 639 status = read_zsreg(uap, R0); 640 641 /* TX busy? Just wait for the TX done interrupt. */ 642 if (!(status & Tx_BUF_EMP)) 643 return; 644 645 /* Send the first character to jump-start the TX done 646 * IRQ sending engine. 647 */ 648 if (port->x_char) { 649 write_zsdata(uap, port->x_char); 650 zssync(uap); 651 port->icount.tx++; 652 port->x_char = 0; 653 } else { 654 struct circ_buf *xmit = &port->state->xmit; 655 656 write_zsdata(uap, xmit->buf[xmit->tail]); 657 zssync(uap); 658 xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1); 659 port->icount.tx++; 660 661 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) 662 uart_write_wakeup(&uap->port); 663 } 664 pmz_debug("pmz: start_tx() done.\n"); 665 } 666 667 /* 668 * Stop Rx side, basically disable emitting of 669 * Rx interrupts on the port. We don't disable the rx 670 * side of the chip proper though 671 * The port lock is held. 672 */ 673 static void pmz_stop_rx(struct uart_port *port) 674 { 675 struct uart_pmac_port *uap = to_pmz(port); 676 677 pmz_debug("pmz: stop_rx()()\n"); 678 679 /* Disable all RX interrupts. */ 680 uap->curregs[R1] &= ~RxINT_MASK; 681 pmz_maybe_update_regs(uap); 682 683 pmz_debug("pmz: stop_rx() done.\n"); 684 } 685 686 /* 687 * Enable modem status change interrupts 688 * The port lock is held. 689 */ 690 static void pmz_enable_ms(struct uart_port *port) 691 { 692 struct uart_pmac_port *uap = to_pmz(port); 693 unsigned char new_reg; 694 695 if (ZS_IS_IRDA(uap)) 696 return; 697 new_reg = uap->curregs[R15] | (DCDIE | SYNCIE | CTSIE); 698 if (new_reg != uap->curregs[R15]) { 699 uap->curregs[R15] = new_reg; 700 701 /* NOTE: Not subject to 'transmitter active' rule. */ 702 write_zsreg(uap, R15, uap->curregs[R15]); 703 } 704 } 705 706 /* 707 * Control break state emission 708 * The port lock is not held. 709 */ 710 static void pmz_break_ctl(struct uart_port *port, int break_state) 711 { 712 struct uart_pmac_port *uap = to_pmz(port); 713 unsigned char set_bits, clear_bits, new_reg; 714 unsigned long flags; 715 716 set_bits = clear_bits = 0; 717 718 if (break_state) 719 set_bits |= SND_BRK; 720 else 721 clear_bits |= SND_BRK; 722 723 spin_lock_irqsave(&port->lock, flags); 724 725 new_reg = (uap->curregs[R5] | set_bits) & ~clear_bits; 726 if (new_reg != uap->curregs[R5]) { 727 uap->curregs[R5] = new_reg; 728 write_zsreg(uap, R5, uap->curregs[R5]); 729 } 730 731 spin_unlock_irqrestore(&port->lock, flags); 732 } 733 734 #ifdef CONFIG_PPC_PMAC 735 736 /* 737 * Turn power on or off to the SCC and associated stuff 738 * (port drivers, modem, IR port, etc.) 739 * Returns the number of milliseconds we should wait before 740 * trying to use the port. 741 */ 742 static int pmz_set_scc_power(struct uart_pmac_port *uap, int state) 743 { 744 int delay = 0; 745 int rc; 746 747 if (state) { 748 rc = pmac_call_feature( 749 PMAC_FTR_SCC_ENABLE, uap->node, uap->port_type, 1); 750 pmz_debug("port power on result: %d\n", rc); 751 if (ZS_IS_INTMODEM(uap)) { 752 rc = pmac_call_feature( 753 PMAC_FTR_MODEM_ENABLE, uap->node, 0, 1); 754 delay = 2500; /* wait for 2.5s before using */ 755 pmz_debug("modem power result: %d\n", rc); 756 } 757 } else { 758 /* TODO: Make that depend on a timer, don't power down 759 * immediately 760 */ 761 if (ZS_IS_INTMODEM(uap)) { 762 rc = pmac_call_feature( 763 PMAC_FTR_MODEM_ENABLE, uap->node, 0, 0); 764 pmz_debug("port power off result: %d\n", rc); 765 } 766 pmac_call_feature(PMAC_FTR_SCC_ENABLE, uap->node, uap->port_type, 0); 767 } 768 return delay; 769 } 770 771 #else 772 773 static int pmz_set_scc_power(struct uart_pmac_port *uap, int state) 774 { 775 return 0; 776 } 777 778 #endif /* !CONFIG_PPC_PMAC */ 779 780 /* 781 * FixZeroBug....Works around a bug in the SCC receiving channel. 782 * Inspired from Darwin code, 15 Sept. 2000 -DanM 783 * 784 * The following sequence prevents a problem that is seen with O'Hare ASICs 785 * (most versions -- also with some Heathrow and Hydra ASICs) where a zero 786 * at the input to the receiver becomes 'stuck' and locks up the receiver. 787 * This problem can occur as a result of a zero bit at the receiver input 788 * coincident with any of the following events: 789 * 790 * The SCC is initialized (hardware or software). 791 * A framing error is detected. 792 * The clocking option changes from synchronous or X1 asynchronous 793 * clocking to X16, X32, or X64 asynchronous clocking. 794 * The decoding mode is changed among NRZ, NRZI, FM0, or FM1. 795 * 796 * This workaround attempts to recover from the lockup condition by placing 797 * the SCC in synchronous loopback mode with a fast clock before programming 798 * any of the asynchronous modes. 799 */ 800 static void pmz_fix_zero_bug_scc(struct uart_pmac_port *uap) 801 { 802 write_zsreg(uap, 9, ZS_IS_CHANNEL_A(uap) ? CHRA : CHRB); 803 zssync(uap); 804 udelay(10); 805 write_zsreg(uap, 9, (ZS_IS_CHANNEL_A(uap) ? CHRA : CHRB) | NV); 806 zssync(uap); 807 808 write_zsreg(uap, 4, X1CLK | MONSYNC); 809 write_zsreg(uap, 3, Rx8); 810 write_zsreg(uap, 5, Tx8 | RTS); 811 write_zsreg(uap, 9, NV); /* Didn't we already do this? */ 812 write_zsreg(uap, 11, RCBR | TCBR); 813 write_zsreg(uap, 12, 0); 814 write_zsreg(uap, 13, 0); 815 write_zsreg(uap, 14, (LOOPBAK | BRSRC)); 816 write_zsreg(uap, 14, (LOOPBAK | BRSRC | BRENAB)); 817 write_zsreg(uap, 3, Rx8 | RxENABLE); 818 write_zsreg(uap, 0, RES_EXT_INT); 819 write_zsreg(uap, 0, RES_EXT_INT); 820 write_zsreg(uap, 0, RES_EXT_INT); /* to kill some time */ 821 822 /* The channel should be OK now, but it is probably receiving 823 * loopback garbage. 824 * Switch to asynchronous mode, disable the receiver, 825 * and discard everything in the receive buffer. 826 */ 827 write_zsreg(uap, 9, NV); 828 write_zsreg(uap, 4, X16CLK | SB_MASK); 829 write_zsreg(uap, 3, Rx8); 830 831 while (read_zsreg(uap, 0) & Rx_CH_AV) { 832 (void)read_zsreg(uap, 8); 833 write_zsreg(uap, 0, RES_EXT_INT); 834 write_zsreg(uap, 0, ERR_RES); 835 } 836 } 837 838 /* 839 * Real startup routine, powers up the hardware and sets up 840 * the SCC. Returns a delay in ms where you need to wait before 841 * actually using the port, this is typically the internal modem 842 * powerup delay. This routine expect the lock to be taken. 843 */ 844 static int __pmz_startup(struct uart_pmac_port *uap) 845 { 846 int pwr_delay = 0; 847 848 memset(&uap->curregs, 0, sizeof(uap->curregs)); 849 850 /* Power up the SCC & underlying hardware (modem/irda) */ 851 pwr_delay = pmz_set_scc_power(uap, 1); 852 853 /* Nice buggy HW ... */ 854 pmz_fix_zero_bug_scc(uap); 855 856 /* Reset the channel */ 857 uap->curregs[R9] = 0; 858 write_zsreg(uap, 9, ZS_IS_CHANNEL_A(uap) ? CHRA : CHRB); 859 zssync(uap); 860 udelay(10); 861 write_zsreg(uap, 9, 0); 862 zssync(uap); 863 864 /* Clear the interrupt registers */ 865 write_zsreg(uap, R1, 0); 866 write_zsreg(uap, R0, ERR_RES); 867 write_zsreg(uap, R0, ERR_RES); 868 write_zsreg(uap, R0, RES_H_IUS); 869 write_zsreg(uap, R0, RES_H_IUS); 870 871 /* Setup some valid baud rate */ 872 uap->curregs[R4] = X16CLK | SB1; 873 uap->curregs[R3] = Rx8; 874 uap->curregs[R5] = Tx8 | RTS; 875 if (!ZS_IS_IRDA(uap)) 876 uap->curregs[R5] |= DTR; 877 uap->curregs[R12] = 0; 878 uap->curregs[R13] = 0; 879 uap->curregs[R14] = BRENAB; 880 881 /* Clear handshaking, enable BREAK interrupts */ 882 uap->curregs[R15] = BRKIE; 883 884 /* Master interrupt enable */ 885 uap->curregs[R9] |= NV | MIE; 886 887 pmz_load_zsregs(uap, uap->curregs); 888 889 /* Enable receiver and transmitter. */ 890 write_zsreg(uap, R3, uap->curregs[R3] |= RxENABLE); 891 write_zsreg(uap, R5, uap->curregs[R5] |= TxENABLE); 892 893 /* Remember status for DCD/CTS changes */ 894 uap->prev_status = read_zsreg(uap, R0); 895 896 return pwr_delay; 897 } 898 899 static void pmz_irda_reset(struct uart_pmac_port *uap) 900 { 901 unsigned long flags; 902 903 spin_lock_irqsave(&uap->port.lock, flags); 904 uap->curregs[R5] |= DTR; 905 write_zsreg(uap, R5, uap->curregs[R5]); 906 zssync(uap); 907 spin_unlock_irqrestore(&uap->port.lock, flags); 908 msleep(110); 909 910 spin_lock_irqsave(&uap->port.lock, flags); 911 uap->curregs[R5] &= ~DTR; 912 write_zsreg(uap, R5, uap->curregs[R5]); 913 zssync(uap); 914 spin_unlock_irqrestore(&uap->port.lock, flags); 915 msleep(10); 916 } 917 918 /* 919 * This is the "normal" startup routine, using the above one 920 * wrapped with the lock and doing a schedule delay 921 */ 922 static int pmz_startup(struct uart_port *port) 923 { 924 struct uart_pmac_port *uap = to_pmz(port); 925 unsigned long flags; 926 int pwr_delay = 0; 927 928 pmz_debug("pmz: startup()\n"); 929 930 uap->flags |= PMACZILOG_FLAG_IS_OPEN; 931 932 /* A console is never powered down. Else, power up and 933 * initialize the chip 934 */ 935 if (!ZS_IS_CONS(uap)) { 936 spin_lock_irqsave(&port->lock, flags); 937 pwr_delay = __pmz_startup(uap); 938 spin_unlock_irqrestore(&port->lock, flags); 939 } 940 sprintf(uap->irq_name, PMACZILOG_NAME"%d", uap->port.line); 941 if (request_irq(uap->port.irq, pmz_interrupt, IRQF_SHARED, 942 uap->irq_name, uap)) { 943 pmz_error("Unable to register zs interrupt handler.\n"); 944 pmz_set_scc_power(uap, 0); 945 return -ENXIO; 946 } 947 948 /* Right now, we deal with delay by blocking here, I'll be 949 * smarter later on 950 */ 951 if (pwr_delay != 0) { 952 pmz_debug("pmz: delaying %d ms\n", pwr_delay); 953 msleep(pwr_delay); 954 } 955 956 /* IrDA reset is done now */ 957 if (ZS_IS_IRDA(uap)) 958 pmz_irda_reset(uap); 959 960 /* Enable interrupt requests for the channel */ 961 spin_lock_irqsave(&port->lock, flags); 962 pmz_interrupt_control(uap, 1); 963 spin_unlock_irqrestore(&port->lock, flags); 964 965 pmz_debug("pmz: startup() done.\n"); 966 967 return 0; 968 } 969 970 static void pmz_shutdown(struct uart_port *port) 971 { 972 struct uart_pmac_port *uap = to_pmz(port); 973 unsigned long flags; 974 975 pmz_debug("pmz: shutdown()\n"); 976 977 spin_lock_irqsave(&port->lock, flags); 978 979 /* Disable interrupt requests for the channel */ 980 pmz_interrupt_control(uap, 0); 981 982 if (!ZS_IS_CONS(uap)) { 983 /* Disable receiver and transmitter */ 984 uap->curregs[R3] &= ~RxENABLE; 985 uap->curregs[R5] &= ~TxENABLE; 986 987 /* Disable break assertion */ 988 uap->curregs[R5] &= ~SND_BRK; 989 pmz_maybe_update_regs(uap); 990 } 991 992 spin_unlock_irqrestore(&port->lock, flags); 993 994 /* Release interrupt handler */ 995 free_irq(uap->port.irq, uap); 996 997 spin_lock_irqsave(&port->lock, flags); 998 999 uap->flags &= ~PMACZILOG_FLAG_IS_OPEN; 1000 1001 if (!ZS_IS_CONS(uap)) 1002 pmz_set_scc_power(uap, 0); /* Shut the chip down */ 1003 1004 spin_unlock_irqrestore(&port->lock, flags); 1005 1006 pmz_debug("pmz: shutdown() done.\n"); 1007 } 1008 1009 /* Shared by TTY driver and serial console setup. The port lock is held 1010 * and local interrupts are disabled. 1011 */ 1012 static void pmz_convert_to_zs(struct uart_pmac_port *uap, unsigned int cflag, 1013 unsigned int iflag, unsigned long baud) 1014 { 1015 int brg; 1016 1017 /* Switch to external clocking for IrDA high clock rates. That 1018 * code could be re-used for Midi interfaces with different 1019 * multipliers 1020 */ 1021 if (baud >= 115200 && ZS_IS_IRDA(uap)) { 1022 uap->curregs[R4] = X1CLK; 1023 uap->curregs[R11] = RCTRxCP | TCTRxCP; 1024 uap->curregs[R14] = 0; /* BRG off */ 1025 uap->curregs[R12] = 0; 1026 uap->curregs[R13] = 0; 1027 uap->flags |= PMACZILOG_FLAG_IS_EXTCLK; 1028 } else { 1029 switch (baud) { 1030 case ZS_CLOCK/16: /* 230400 */ 1031 uap->curregs[R4] = X16CLK; 1032 uap->curregs[R11] = 0; 1033 uap->curregs[R14] = 0; 1034 break; 1035 case ZS_CLOCK/32: /* 115200 */ 1036 uap->curregs[R4] = X32CLK; 1037 uap->curregs[R11] = 0; 1038 uap->curregs[R14] = 0; 1039 break; 1040 default: 1041 uap->curregs[R4] = X16CLK; 1042 uap->curregs[R11] = TCBR | RCBR; 1043 brg = BPS_TO_BRG(baud, ZS_CLOCK / 16); 1044 uap->curregs[R12] = (brg & 255); 1045 uap->curregs[R13] = ((brg >> 8) & 255); 1046 uap->curregs[R14] = BRENAB; 1047 } 1048 uap->flags &= ~PMACZILOG_FLAG_IS_EXTCLK; 1049 } 1050 1051 /* Character size, stop bits, and parity. */ 1052 uap->curregs[3] &= ~RxN_MASK; 1053 uap->curregs[5] &= ~TxN_MASK; 1054 1055 switch (cflag & CSIZE) { 1056 case CS5: 1057 uap->curregs[3] |= Rx5; 1058 uap->curregs[5] |= Tx5; 1059 uap->parity_mask = 0x1f; 1060 break; 1061 case CS6: 1062 uap->curregs[3] |= Rx6; 1063 uap->curregs[5] |= Tx6; 1064 uap->parity_mask = 0x3f; 1065 break; 1066 case CS7: 1067 uap->curregs[3] |= Rx7; 1068 uap->curregs[5] |= Tx7; 1069 uap->parity_mask = 0x7f; 1070 break; 1071 case CS8: 1072 default: 1073 uap->curregs[3] |= Rx8; 1074 uap->curregs[5] |= Tx8; 1075 uap->parity_mask = 0xff; 1076 break; 1077 }; 1078 uap->curregs[4] &= ~(SB_MASK); 1079 if (cflag & CSTOPB) 1080 uap->curregs[4] |= SB2; 1081 else 1082 uap->curregs[4] |= SB1; 1083 if (cflag & PARENB) 1084 uap->curregs[4] |= PAR_ENAB; 1085 else 1086 uap->curregs[4] &= ~PAR_ENAB; 1087 if (!(cflag & PARODD)) 1088 uap->curregs[4] |= PAR_EVEN; 1089 else 1090 uap->curregs[4] &= ~PAR_EVEN; 1091 1092 uap->port.read_status_mask = Rx_OVR; 1093 if (iflag & INPCK) 1094 uap->port.read_status_mask |= CRC_ERR | PAR_ERR; 1095 if (iflag & (BRKINT | PARMRK)) 1096 uap->port.read_status_mask |= BRK_ABRT; 1097 1098 uap->port.ignore_status_mask = 0; 1099 if (iflag & IGNPAR) 1100 uap->port.ignore_status_mask |= CRC_ERR | PAR_ERR; 1101 if (iflag & IGNBRK) { 1102 uap->port.ignore_status_mask |= BRK_ABRT; 1103 if (iflag & IGNPAR) 1104 uap->port.ignore_status_mask |= Rx_OVR; 1105 } 1106 1107 if ((cflag & CREAD) == 0) 1108 uap->port.ignore_status_mask = 0xff; 1109 } 1110 1111 1112 /* 1113 * Set the irda codec on the imac to the specified baud rate. 1114 */ 1115 static void pmz_irda_setup(struct uart_pmac_port *uap, unsigned long *baud) 1116 { 1117 u8 cmdbyte; 1118 int t, version; 1119 1120 switch (*baud) { 1121 /* SIR modes */ 1122 case 2400: 1123 cmdbyte = 0x53; 1124 break; 1125 case 4800: 1126 cmdbyte = 0x52; 1127 break; 1128 case 9600: 1129 cmdbyte = 0x51; 1130 break; 1131 case 19200: 1132 cmdbyte = 0x50; 1133 break; 1134 case 38400: 1135 cmdbyte = 0x4f; 1136 break; 1137 case 57600: 1138 cmdbyte = 0x4e; 1139 break; 1140 case 115200: 1141 cmdbyte = 0x4d; 1142 break; 1143 /* The FIR modes aren't really supported at this point, how 1144 * do we select the speed ? via the FCR on KeyLargo ? 1145 */ 1146 case 1152000: 1147 cmdbyte = 0; 1148 break; 1149 case 4000000: 1150 cmdbyte = 0; 1151 break; 1152 default: /* 9600 */ 1153 cmdbyte = 0x51; 1154 *baud = 9600; 1155 break; 1156 } 1157 1158 /* Wait for transmitter to drain */ 1159 t = 10000; 1160 while ((read_zsreg(uap, R0) & Tx_BUF_EMP) == 0 1161 || (read_zsreg(uap, R1) & ALL_SNT) == 0) { 1162 if (--t <= 0) { 1163 pmz_error("transmitter didn't drain\n"); 1164 return; 1165 } 1166 udelay(10); 1167 } 1168 1169 /* Drain the receiver too */ 1170 t = 100; 1171 (void)read_zsdata(uap); 1172 (void)read_zsdata(uap); 1173 (void)read_zsdata(uap); 1174 mdelay(10); 1175 while (read_zsreg(uap, R0) & Rx_CH_AV) { 1176 read_zsdata(uap); 1177 mdelay(10); 1178 if (--t <= 0) { 1179 pmz_error("receiver didn't drain\n"); 1180 return; 1181 } 1182 } 1183 1184 /* Switch to command mode */ 1185 uap->curregs[R5] |= DTR; 1186 write_zsreg(uap, R5, uap->curregs[R5]); 1187 zssync(uap); 1188 mdelay(1); 1189 1190 /* Switch SCC to 19200 */ 1191 pmz_convert_to_zs(uap, CS8, 0, 19200); 1192 pmz_load_zsregs(uap, uap->curregs); 1193 mdelay(1); 1194 1195 /* Write get_version command byte */ 1196 write_zsdata(uap, 1); 1197 t = 5000; 1198 while ((read_zsreg(uap, R0) & Rx_CH_AV) == 0) { 1199 if (--t <= 0) { 1200 pmz_error("irda_setup timed out on get_version byte\n"); 1201 goto out; 1202 } 1203 udelay(10); 1204 } 1205 version = read_zsdata(uap); 1206 1207 if (version < 4) { 1208 pmz_info("IrDA: dongle version %d not supported\n", version); 1209 goto out; 1210 } 1211 1212 /* Send speed mode */ 1213 write_zsdata(uap, cmdbyte); 1214 t = 5000; 1215 while ((read_zsreg(uap, R0) & Rx_CH_AV) == 0) { 1216 if (--t <= 0) { 1217 pmz_error("irda_setup timed out on speed mode byte\n"); 1218 goto out; 1219 } 1220 udelay(10); 1221 } 1222 t = read_zsdata(uap); 1223 if (t != cmdbyte) 1224 pmz_error("irda_setup speed mode byte = %x (%x)\n", t, cmdbyte); 1225 1226 pmz_info("IrDA setup for %ld bps, dongle version: %d\n", 1227 *baud, version); 1228 1229 (void)read_zsdata(uap); 1230 (void)read_zsdata(uap); 1231 (void)read_zsdata(uap); 1232 1233 out: 1234 /* Switch back to data mode */ 1235 uap->curregs[R5] &= ~DTR; 1236 write_zsreg(uap, R5, uap->curregs[R5]); 1237 zssync(uap); 1238 1239 (void)read_zsdata(uap); 1240 (void)read_zsdata(uap); 1241 (void)read_zsdata(uap); 1242 } 1243 1244 1245 static void __pmz_set_termios(struct uart_port *port, struct ktermios *termios, 1246 struct ktermios *old) 1247 { 1248 struct uart_pmac_port *uap = to_pmz(port); 1249 unsigned long baud; 1250 1251 pmz_debug("pmz: set_termios()\n"); 1252 1253 memcpy(&uap->termios_cache, termios, sizeof(struct ktermios)); 1254 1255 /* XXX Check which revs of machines actually allow 1 and 4Mb speeds 1256 * on the IR dongle. Note that the IRTTY driver currently doesn't know 1257 * about the FIR mode and high speed modes. So these are unused. For 1258 * implementing proper support for these, we should probably add some 1259 * DMA as well, at least on the Rx side, which isn't a simple thing 1260 * at this point. 1261 */ 1262 if (ZS_IS_IRDA(uap)) { 1263 /* Calc baud rate */ 1264 baud = uart_get_baud_rate(port, termios, old, 1200, 4000000); 1265 pmz_debug("pmz: switch IRDA to %ld bauds\n", baud); 1266 /* Cet the irda codec to the right rate */ 1267 pmz_irda_setup(uap, &baud); 1268 /* Set final baud rate */ 1269 pmz_convert_to_zs(uap, termios->c_cflag, termios->c_iflag, baud); 1270 pmz_load_zsregs(uap, uap->curregs); 1271 zssync(uap); 1272 } else { 1273 baud = uart_get_baud_rate(port, termios, old, 1200, 230400); 1274 pmz_convert_to_zs(uap, termios->c_cflag, termios->c_iflag, baud); 1275 /* Make sure modem status interrupts are correctly configured */ 1276 if (UART_ENABLE_MS(&uap->port, termios->c_cflag)) { 1277 uap->curregs[R15] |= DCDIE | SYNCIE | CTSIE; 1278 uap->flags |= PMACZILOG_FLAG_MODEM_STATUS; 1279 } else { 1280 uap->curregs[R15] &= ~(DCDIE | SYNCIE | CTSIE); 1281 uap->flags &= ~PMACZILOG_FLAG_MODEM_STATUS; 1282 } 1283 1284 /* Load registers to the chip */ 1285 pmz_maybe_update_regs(uap); 1286 } 1287 uart_update_timeout(port, termios->c_cflag, baud); 1288 1289 pmz_debug("pmz: set_termios() done.\n"); 1290 } 1291 1292 /* The port lock is not held. */ 1293 static void pmz_set_termios(struct uart_port *port, struct ktermios *termios, 1294 struct ktermios *old) 1295 { 1296 struct uart_pmac_port *uap = to_pmz(port); 1297 unsigned long flags; 1298 1299 spin_lock_irqsave(&port->lock, flags); 1300 1301 /* Disable IRQs on the port */ 1302 pmz_interrupt_control(uap, 0); 1303 1304 /* Setup new port configuration */ 1305 __pmz_set_termios(port, termios, old); 1306 1307 /* Re-enable IRQs on the port */ 1308 if (ZS_IS_OPEN(uap)) 1309 pmz_interrupt_control(uap, 1); 1310 1311 spin_unlock_irqrestore(&port->lock, flags); 1312 } 1313 1314 static const char *pmz_type(struct uart_port *port) 1315 { 1316 struct uart_pmac_port *uap = to_pmz(port); 1317 1318 if (ZS_IS_IRDA(uap)) 1319 return "Z85c30 ESCC - Infrared port"; 1320 else if (ZS_IS_INTMODEM(uap)) 1321 return "Z85c30 ESCC - Internal modem"; 1322 return "Z85c30 ESCC - Serial port"; 1323 } 1324 1325 /* We do not request/release mappings of the registers here, this 1326 * happens at early serial probe time. 1327 */ 1328 static void pmz_release_port(struct uart_port *port) 1329 { 1330 } 1331 1332 static int pmz_request_port(struct uart_port *port) 1333 { 1334 return 0; 1335 } 1336 1337 /* These do not need to do anything interesting either. */ 1338 static void pmz_config_port(struct uart_port *port, int flags) 1339 { 1340 } 1341 1342 /* We do not support letting the user mess with the divisor, IRQ, etc. */ 1343 static int pmz_verify_port(struct uart_port *port, struct serial_struct *ser) 1344 { 1345 return -EINVAL; 1346 } 1347 1348 #ifdef CONFIG_CONSOLE_POLL 1349 1350 static int pmz_poll_get_char(struct uart_port *port) 1351 { 1352 struct uart_pmac_port *uap = (struct uart_pmac_port *)port; 1353 int tries = 2; 1354 1355 while (tries) { 1356 if ((read_zsreg(uap, R0) & Rx_CH_AV) != 0) 1357 return read_zsdata(uap); 1358 if (tries--) 1359 udelay(5); 1360 } 1361 1362 return NO_POLL_CHAR; 1363 } 1364 1365 static void pmz_poll_put_char(struct uart_port *port, unsigned char c) 1366 { 1367 struct uart_pmac_port *uap = (struct uart_pmac_port *)port; 1368 1369 /* Wait for the transmit buffer to empty. */ 1370 while ((read_zsreg(uap, R0) & Tx_BUF_EMP) == 0) 1371 udelay(5); 1372 write_zsdata(uap, c); 1373 } 1374 1375 #endif /* CONFIG_CONSOLE_POLL */ 1376 1377 static struct uart_ops pmz_pops = { 1378 .tx_empty = pmz_tx_empty, 1379 .set_mctrl = pmz_set_mctrl, 1380 .get_mctrl = pmz_get_mctrl, 1381 .stop_tx = pmz_stop_tx, 1382 .start_tx = pmz_start_tx, 1383 .stop_rx = pmz_stop_rx, 1384 .enable_ms = pmz_enable_ms, 1385 .break_ctl = pmz_break_ctl, 1386 .startup = pmz_startup, 1387 .shutdown = pmz_shutdown, 1388 .set_termios = pmz_set_termios, 1389 .type = pmz_type, 1390 .release_port = pmz_release_port, 1391 .request_port = pmz_request_port, 1392 .config_port = pmz_config_port, 1393 .verify_port = pmz_verify_port, 1394 #ifdef CONFIG_CONSOLE_POLL 1395 .poll_get_char = pmz_poll_get_char, 1396 .poll_put_char = pmz_poll_put_char, 1397 #endif 1398 }; 1399 1400 #ifdef CONFIG_PPC_PMAC 1401 1402 /* 1403 * Setup one port structure after probing, HW is down at this point, 1404 * Unlike sunzilog, we don't need to pre-init the spinlock as we don't 1405 * register our console before uart_add_one_port() is called 1406 */ 1407 static int __init pmz_init_port(struct uart_pmac_port *uap) 1408 { 1409 struct device_node *np = uap->node; 1410 const char *conn; 1411 const struct slot_names_prop { 1412 int count; 1413 char name[1]; 1414 } *slots; 1415 int len; 1416 struct resource r_ports, r_rxdma, r_txdma; 1417 1418 /* 1419 * Request & map chip registers 1420 */ 1421 if (of_address_to_resource(np, 0, &r_ports)) 1422 return -ENODEV; 1423 uap->port.mapbase = r_ports.start; 1424 uap->port.membase = ioremap(uap->port.mapbase, 0x1000); 1425 1426 uap->control_reg = uap->port.membase; 1427 uap->data_reg = uap->control_reg + 0x10; 1428 1429 /* 1430 * Request & map DBDMA registers 1431 */ 1432 #ifdef HAS_DBDMA 1433 if (of_address_to_resource(np, 1, &r_txdma) == 0 && 1434 of_address_to_resource(np, 2, &r_rxdma) == 0) 1435 uap->flags |= PMACZILOG_FLAG_HAS_DMA; 1436 #else 1437 memset(&r_txdma, 0, sizeof(struct resource)); 1438 memset(&r_rxdma, 0, sizeof(struct resource)); 1439 #endif 1440 if (ZS_HAS_DMA(uap)) { 1441 uap->tx_dma_regs = ioremap(r_txdma.start, 0x100); 1442 if (uap->tx_dma_regs == NULL) { 1443 uap->flags &= ~PMACZILOG_FLAG_HAS_DMA; 1444 goto no_dma; 1445 } 1446 uap->rx_dma_regs = ioremap(r_rxdma.start, 0x100); 1447 if (uap->rx_dma_regs == NULL) { 1448 iounmap(uap->tx_dma_regs); 1449 uap->tx_dma_regs = NULL; 1450 uap->flags &= ~PMACZILOG_FLAG_HAS_DMA; 1451 goto no_dma; 1452 } 1453 uap->tx_dma_irq = irq_of_parse_and_map(np, 1); 1454 uap->rx_dma_irq = irq_of_parse_and_map(np, 2); 1455 } 1456 no_dma: 1457 1458 /* 1459 * Detect port type 1460 */ 1461 if (of_device_is_compatible(np, "cobalt")) 1462 uap->flags |= PMACZILOG_FLAG_IS_INTMODEM; 1463 conn = of_get_property(np, "AAPL,connector", &len); 1464 if (conn && (strcmp(conn, "infrared") == 0)) 1465 uap->flags |= PMACZILOG_FLAG_IS_IRDA; 1466 uap->port_type = PMAC_SCC_ASYNC; 1467 /* 1999 Powerbook G3 has slot-names property instead */ 1468 slots = of_get_property(np, "slot-names", &len); 1469 if (slots && slots->count > 0) { 1470 if (strcmp(slots->name, "IrDA") == 0) 1471 uap->flags |= PMACZILOG_FLAG_IS_IRDA; 1472 else if (strcmp(slots->name, "Modem") == 0) 1473 uap->flags |= PMACZILOG_FLAG_IS_INTMODEM; 1474 } 1475 if (ZS_IS_IRDA(uap)) 1476 uap->port_type = PMAC_SCC_IRDA; 1477 if (ZS_IS_INTMODEM(uap)) { 1478 struct device_node* i2c_modem = 1479 of_find_node_by_name(NULL, "i2c-modem"); 1480 if (i2c_modem) { 1481 const char* mid = 1482 of_get_property(i2c_modem, "modem-id", NULL); 1483 if (mid) switch(*mid) { 1484 case 0x04 : 1485 case 0x05 : 1486 case 0x07 : 1487 case 0x08 : 1488 case 0x0b : 1489 case 0x0c : 1490 uap->port_type = PMAC_SCC_I2S1; 1491 } 1492 printk(KERN_INFO "pmac_zilog: i2c-modem detected, id: %d\n", 1493 mid ? (*mid) : 0); 1494 of_node_put(i2c_modem); 1495 } else { 1496 printk(KERN_INFO "pmac_zilog: serial modem detected\n"); 1497 } 1498 } 1499 1500 /* 1501 * Init remaining bits of "port" structure 1502 */ 1503 uap->port.iotype = UPIO_MEM; 1504 uap->port.irq = irq_of_parse_and_map(np, 0); 1505 uap->port.uartclk = ZS_CLOCK; 1506 uap->port.fifosize = 1; 1507 uap->port.ops = &pmz_pops; 1508 uap->port.type = PORT_PMAC_ZILOG; 1509 uap->port.flags = 0; 1510 1511 /* 1512 * Fixup for the port on Gatwick for which the device-tree has 1513 * missing interrupts. Normally, the macio_dev would contain 1514 * fixed up interrupt info, but we use the device-tree directly 1515 * here due to early probing so we need the fixup too. 1516 */ 1517 if (uap->port.irq == 0 && 1518 np->parent && np->parent->parent && 1519 of_device_is_compatible(np->parent->parent, "gatwick")) { 1520 /* IRQs on gatwick are offset by 64 */ 1521 uap->port.irq = irq_create_mapping(NULL, 64 + 15); 1522 uap->tx_dma_irq = irq_create_mapping(NULL, 64 + 4); 1523 uap->rx_dma_irq = irq_create_mapping(NULL, 64 + 5); 1524 } 1525 1526 /* Setup some valid baud rate information in the register 1527 * shadows so we don't write crap there before baud rate is 1528 * first initialized. 1529 */ 1530 pmz_convert_to_zs(uap, CS8, 0, 9600); 1531 1532 return 0; 1533 } 1534 1535 /* 1536 * Get rid of a port on module removal 1537 */ 1538 static void pmz_dispose_port(struct uart_pmac_port *uap) 1539 { 1540 struct device_node *np; 1541 1542 np = uap->node; 1543 iounmap(uap->rx_dma_regs); 1544 iounmap(uap->tx_dma_regs); 1545 iounmap(uap->control_reg); 1546 uap->node = NULL; 1547 of_node_put(np); 1548 memset(uap, 0, sizeof(struct uart_pmac_port)); 1549 } 1550 1551 /* 1552 * Called upon match with an escc node in the device-tree. 1553 */ 1554 static int pmz_attach(struct macio_dev *mdev, const struct of_device_id *match) 1555 { 1556 struct uart_pmac_port *uap; 1557 int i; 1558 1559 /* Iterate the pmz_ports array to find a matching entry 1560 */ 1561 for (i = 0; i < MAX_ZS_PORTS; i++) 1562 if (pmz_ports[i].node == mdev->ofdev.dev.of_node) 1563 break; 1564 if (i >= MAX_ZS_PORTS) 1565 return -ENODEV; 1566 1567 1568 uap = &pmz_ports[i]; 1569 uap->dev = mdev; 1570 uap->port.dev = &mdev->ofdev.dev; 1571 dev_set_drvdata(&mdev->ofdev.dev, uap); 1572 1573 /* We still activate the port even when failing to request resources 1574 * to work around bugs in ancient Apple device-trees 1575 */ 1576 if (macio_request_resources(uap->dev, "pmac_zilog")) 1577 printk(KERN_WARNING "%s: Failed to request resource" 1578 ", port still active\n", 1579 uap->node->name); 1580 else 1581 uap->flags |= PMACZILOG_FLAG_RSRC_REQUESTED; 1582 1583 return uart_add_one_port(&pmz_uart_reg, &uap->port); 1584 } 1585 1586 /* 1587 * That one should not be called, macio isn't really a hotswap device, 1588 * we don't expect one of those serial ports to go away... 1589 */ 1590 static int pmz_detach(struct macio_dev *mdev) 1591 { 1592 struct uart_pmac_port *uap = dev_get_drvdata(&mdev->ofdev.dev); 1593 1594 if (!uap) 1595 return -ENODEV; 1596 1597 uart_remove_one_port(&pmz_uart_reg, &uap->port); 1598 1599 if (uap->flags & PMACZILOG_FLAG_RSRC_REQUESTED) { 1600 macio_release_resources(uap->dev); 1601 uap->flags &= ~PMACZILOG_FLAG_RSRC_REQUESTED; 1602 } 1603 dev_set_drvdata(&mdev->ofdev.dev, NULL); 1604 uap->dev = NULL; 1605 uap->port.dev = NULL; 1606 1607 return 0; 1608 } 1609 1610 1611 static int pmz_suspend(struct macio_dev *mdev, pm_message_t pm_state) 1612 { 1613 struct uart_pmac_port *uap = dev_get_drvdata(&mdev->ofdev.dev); 1614 1615 if (uap == NULL) { 1616 printk("HRM... pmz_suspend with NULL uap\n"); 1617 return 0; 1618 } 1619 1620 uart_suspend_port(&pmz_uart_reg, &uap->port); 1621 1622 return 0; 1623 } 1624 1625 1626 static int pmz_resume(struct macio_dev *mdev) 1627 { 1628 struct uart_pmac_port *uap = dev_get_drvdata(&mdev->ofdev.dev); 1629 1630 if (uap == NULL) 1631 return 0; 1632 1633 uart_resume_port(&pmz_uart_reg, &uap->port); 1634 1635 return 0; 1636 } 1637 1638 /* 1639 * Probe all ports in the system and build the ports array, we register 1640 * with the serial layer later, so we get a proper struct device which 1641 * allows the tty to attach properly. This is later than it used to be 1642 * but the tty layer really wants it that way. 1643 */ 1644 static int __init pmz_probe(void) 1645 { 1646 struct device_node *node_p, *node_a, *node_b, *np; 1647 int count = 0; 1648 int rc; 1649 1650 /* 1651 * Find all escc chips in the system 1652 */ 1653 node_p = of_find_node_by_name(NULL, "escc"); 1654 while (node_p) { 1655 /* 1656 * First get channel A/B node pointers 1657 * 1658 * TODO: Add routines with proper locking to do that... 1659 */ 1660 node_a = node_b = NULL; 1661 for (np = NULL; (np = of_get_next_child(node_p, np)) != NULL;) { 1662 if (strncmp(np->name, "ch-a", 4) == 0) 1663 node_a = of_node_get(np); 1664 else if (strncmp(np->name, "ch-b", 4) == 0) 1665 node_b = of_node_get(np); 1666 } 1667 if (!node_a && !node_b) { 1668 of_node_put(node_a); 1669 of_node_put(node_b); 1670 printk(KERN_ERR "pmac_zilog: missing node %c for escc %s\n", 1671 (!node_a) ? 'a' : 'b', node_p->full_name); 1672 goto next; 1673 } 1674 1675 /* 1676 * Fill basic fields in the port structures 1677 */ 1678 if (node_b != NULL) { 1679 pmz_ports[count].mate = &pmz_ports[count+1]; 1680 pmz_ports[count+1].mate = &pmz_ports[count]; 1681 } 1682 pmz_ports[count].flags = PMACZILOG_FLAG_IS_CHANNEL_A; 1683 pmz_ports[count].node = node_a; 1684 pmz_ports[count+1].node = node_b; 1685 pmz_ports[count].port.line = count; 1686 pmz_ports[count+1].port.line = count+1; 1687 1688 /* 1689 * Setup the ports for real 1690 */ 1691 rc = pmz_init_port(&pmz_ports[count]); 1692 if (rc == 0 && node_b != NULL) 1693 rc = pmz_init_port(&pmz_ports[count+1]); 1694 if (rc != 0) { 1695 of_node_put(node_a); 1696 of_node_put(node_b); 1697 memset(&pmz_ports[count], 0, sizeof(struct uart_pmac_port)); 1698 memset(&pmz_ports[count+1], 0, sizeof(struct uart_pmac_port)); 1699 goto next; 1700 } 1701 count += 2; 1702 next: 1703 node_p = of_find_node_by_name(node_p, "escc"); 1704 } 1705 pmz_ports_count = count; 1706 1707 return 0; 1708 } 1709 1710 #else 1711 1712 extern struct platform_device scc_a_pdev, scc_b_pdev; 1713 1714 static int __init pmz_init_port(struct uart_pmac_port *uap) 1715 { 1716 struct resource *r_ports; 1717 int irq; 1718 1719 r_ports = platform_get_resource(uap->pdev, IORESOURCE_MEM, 0); 1720 irq = platform_get_irq(uap->pdev, 0); 1721 if (!r_ports || !irq) 1722 return -ENODEV; 1723 1724 uap->port.mapbase = r_ports->start; 1725 uap->port.membase = (unsigned char __iomem *) r_ports->start; 1726 uap->port.iotype = UPIO_MEM; 1727 uap->port.irq = irq; 1728 uap->port.uartclk = ZS_CLOCK; 1729 uap->port.fifosize = 1; 1730 uap->port.ops = &pmz_pops; 1731 uap->port.type = PORT_PMAC_ZILOG; 1732 uap->port.flags = 0; 1733 1734 uap->control_reg = uap->port.membase; 1735 uap->data_reg = uap->control_reg + 4; 1736 uap->port_type = 0; 1737 1738 pmz_convert_to_zs(uap, CS8, 0, 9600); 1739 1740 return 0; 1741 } 1742 1743 static int __init pmz_probe(void) 1744 { 1745 int err; 1746 1747 pmz_ports_count = 0; 1748 1749 pmz_ports[0].port.line = 0; 1750 pmz_ports[0].flags = PMACZILOG_FLAG_IS_CHANNEL_A; 1751 pmz_ports[0].pdev = &scc_a_pdev; 1752 err = pmz_init_port(&pmz_ports[0]); 1753 if (err) 1754 return err; 1755 pmz_ports_count++; 1756 1757 pmz_ports[0].mate = &pmz_ports[1]; 1758 pmz_ports[1].mate = &pmz_ports[0]; 1759 pmz_ports[1].port.line = 1; 1760 pmz_ports[1].flags = 0; 1761 pmz_ports[1].pdev = &scc_b_pdev; 1762 err = pmz_init_port(&pmz_ports[1]); 1763 if (err) 1764 return err; 1765 pmz_ports_count++; 1766 1767 return 0; 1768 } 1769 1770 static void pmz_dispose_port(struct uart_pmac_port *uap) 1771 { 1772 memset(uap, 0, sizeof(struct uart_pmac_port)); 1773 } 1774 1775 static int __init pmz_attach(struct platform_device *pdev) 1776 { 1777 struct uart_pmac_port *uap; 1778 int i; 1779 1780 /* Iterate the pmz_ports array to find a matching entry */ 1781 for (i = 0; i < pmz_ports_count; i++) 1782 if (pmz_ports[i].pdev == pdev) 1783 break; 1784 if (i >= pmz_ports_count) 1785 return -ENODEV; 1786 1787 uap = &pmz_ports[i]; 1788 uap->port.dev = &pdev->dev; 1789 platform_set_drvdata(pdev, uap); 1790 1791 return uart_add_one_port(&pmz_uart_reg, &uap->port); 1792 } 1793 1794 static int __exit pmz_detach(struct platform_device *pdev) 1795 { 1796 struct uart_pmac_port *uap = platform_get_drvdata(pdev); 1797 1798 if (!uap) 1799 return -ENODEV; 1800 1801 uart_remove_one_port(&pmz_uart_reg, &uap->port); 1802 1803 uap->port.dev = NULL; 1804 1805 return 0; 1806 } 1807 1808 #endif /* !CONFIG_PPC_PMAC */ 1809 1810 #ifdef CONFIG_SERIAL_PMACZILOG_CONSOLE 1811 1812 static void pmz_console_write(struct console *con, const char *s, unsigned int count); 1813 static int __init pmz_console_setup(struct console *co, char *options); 1814 1815 static struct console pmz_console = { 1816 .name = PMACZILOG_NAME, 1817 .write = pmz_console_write, 1818 .device = uart_console_device, 1819 .setup = pmz_console_setup, 1820 .flags = CON_PRINTBUFFER, 1821 .index = -1, 1822 .data = &pmz_uart_reg, 1823 }; 1824 1825 #define PMACZILOG_CONSOLE &pmz_console 1826 #else /* CONFIG_SERIAL_PMACZILOG_CONSOLE */ 1827 #define PMACZILOG_CONSOLE (NULL) 1828 #endif /* CONFIG_SERIAL_PMACZILOG_CONSOLE */ 1829 1830 /* 1831 * Register the driver, console driver and ports with the serial 1832 * core 1833 */ 1834 static int __init pmz_register(void) 1835 { 1836 pmz_uart_reg.nr = pmz_ports_count; 1837 pmz_uart_reg.cons = PMACZILOG_CONSOLE; 1838 1839 /* 1840 * Register this driver with the serial core 1841 */ 1842 return uart_register_driver(&pmz_uart_reg); 1843 } 1844 1845 #ifdef CONFIG_PPC_PMAC 1846 1847 static struct of_device_id pmz_match[] = 1848 { 1849 { 1850 .name = "ch-a", 1851 }, 1852 { 1853 .name = "ch-b", 1854 }, 1855 {}, 1856 }; 1857 MODULE_DEVICE_TABLE (of, pmz_match); 1858 1859 static struct macio_driver pmz_driver = { 1860 .driver = { 1861 .name = "pmac_zilog", 1862 .owner = THIS_MODULE, 1863 .of_match_table = pmz_match, 1864 }, 1865 .probe = pmz_attach, 1866 .remove = pmz_detach, 1867 .suspend = pmz_suspend, 1868 .resume = pmz_resume, 1869 }; 1870 1871 #else 1872 1873 static struct platform_driver pmz_driver = { 1874 .remove = __exit_p(pmz_detach), 1875 .driver = { 1876 .name = "scc", 1877 .owner = THIS_MODULE, 1878 }, 1879 }; 1880 1881 #endif /* !CONFIG_PPC_PMAC */ 1882 1883 static int __init init_pmz(void) 1884 { 1885 int rc, i; 1886 printk(KERN_INFO "%s\n", version); 1887 1888 /* 1889 * First, we need to do a direct OF-based probe pass. We 1890 * do that because we want serial console up before the 1891 * macio stuffs calls us back, and since that makes it 1892 * easier to pass the proper number of channels to 1893 * uart_register_driver() 1894 */ 1895 if (pmz_ports_count == 0) 1896 pmz_probe(); 1897 1898 /* 1899 * Bail early if no port found 1900 */ 1901 if (pmz_ports_count == 0) 1902 return -ENODEV; 1903 1904 /* 1905 * Now we register with the serial layer 1906 */ 1907 rc = pmz_register(); 1908 if (rc) { 1909 printk(KERN_ERR 1910 "pmac_zilog: Error registering serial device, disabling pmac_zilog.\n" 1911 "pmac_zilog: Did another serial driver already claim the minors?\n"); 1912 /* effectively "pmz_unprobe()" */ 1913 for (i=0; i < pmz_ports_count; i++) 1914 pmz_dispose_port(&pmz_ports[i]); 1915 return rc; 1916 } 1917 1918 /* 1919 * Then we register the macio driver itself 1920 */ 1921 #ifdef CONFIG_PPC_PMAC 1922 return macio_register_driver(&pmz_driver); 1923 #else 1924 return platform_driver_probe(&pmz_driver, pmz_attach); 1925 #endif 1926 } 1927 1928 static void __exit exit_pmz(void) 1929 { 1930 int i; 1931 1932 #ifdef CONFIG_PPC_PMAC 1933 /* Get rid of macio-driver (detach from macio) */ 1934 macio_unregister_driver(&pmz_driver); 1935 #else 1936 platform_driver_unregister(&pmz_driver); 1937 #endif 1938 1939 for (i = 0; i < pmz_ports_count; i++) { 1940 struct uart_pmac_port *uport = &pmz_ports[i]; 1941 #ifdef CONFIG_PPC_PMAC 1942 if (uport->node != NULL) 1943 pmz_dispose_port(uport); 1944 #else 1945 if (uport->pdev != NULL) 1946 pmz_dispose_port(uport); 1947 #endif 1948 } 1949 /* Unregister UART driver */ 1950 uart_unregister_driver(&pmz_uart_reg); 1951 } 1952 1953 #ifdef CONFIG_SERIAL_PMACZILOG_CONSOLE 1954 1955 static void pmz_console_putchar(struct uart_port *port, int ch) 1956 { 1957 struct uart_pmac_port *uap = (struct uart_pmac_port *)port; 1958 1959 /* Wait for the transmit buffer to empty. */ 1960 while ((read_zsreg(uap, R0) & Tx_BUF_EMP) == 0) 1961 udelay(5); 1962 write_zsdata(uap, ch); 1963 } 1964 1965 /* 1966 * Print a string to the serial port trying not to disturb 1967 * any possible real use of the port... 1968 */ 1969 static void pmz_console_write(struct console *con, const char *s, unsigned int count) 1970 { 1971 struct uart_pmac_port *uap = &pmz_ports[con->index]; 1972 unsigned long flags; 1973 1974 spin_lock_irqsave(&uap->port.lock, flags); 1975 1976 /* Turn of interrupts and enable the transmitter. */ 1977 write_zsreg(uap, R1, uap->curregs[1] & ~TxINT_ENAB); 1978 write_zsreg(uap, R5, uap->curregs[5] | TxENABLE | RTS | DTR); 1979 1980 uart_console_write(&uap->port, s, count, pmz_console_putchar); 1981 1982 /* Restore the values in the registers. */ 1983 write_zsreg(uap, R1, uap->curregs[1]); 1984 /* Don't disable the transmitter. */ 1985 1986 spin_unlock_irqrestore(&uap->port.lock, flags); 1987 } 1988 1989 /* 1990 * Setup the serial console 1991 */ 1992 static int __init pmz_console_setup(struct console *co, char *options) 1993 { 1994 struct uart_pmac_port *uap; 1995 struct uart_port *port; 1996 int baud = 38400; 1997 int bits = 8; 1998 int parity = 'n'; 1999 int flow = 'n'; 2000 unsigned long pwr_delay; 2001 2002 /* 2003 * XServe's default to 57600 bps 2004 */ 2005 if (of_machine_is_compatible("RackMac1,1") 2006 || of_machine_is_compatible("RackMac1,2") 2007 || of_machine_is_compatible("MacRISC4")) 2008 baud = 57600; 2009 2010 /* 2011 * Check whether an invalid uart number has been specified, and 2012 * if so, search for the first available port that does have 2013 * console support. 2014 */ 2015 if (co->index >= pmz_ports_count) 2016 co->index = 0; 2017 uap = &pmz_ports[co->index]; 2018 #ifdef CONFIG_PPC_PMAC 2019 if (uap->node == NULL) 2020 return -ENODEV; 2021 #else 2022 if (uap->pdev == NULL) 2023 return -ENODEV; 2024 #endif 2025 port = &uap->port; 2026 2027 /* 2028 * Mark port as beeing a console 2029 */ 2030 uap->flags |= PMACZILOG_FLAG_IS_CONS; 2031 2032 /* 2033 * Temporary fix for uart layer who didn't setup the spinlock yet 2034 */ 2035 spin_lock_init(&port->lock); 2036 2037 /* 2038 * Enable the hardware 2039 */ 2040 pwr_delay = __pmz_startup(uap); 2041 if (pwr_delay) 2042 mdelay(pwr_delay); 2043 2044 if (options) 2045 uart_parse_options(options, &baud, &parity, &bits, &flow); 2046 2047 return uart_set_options(port, co, baud, parity, bits, flow); 2048 } 2049 2050 static int __init pmz_console_init(void) 2051 { 2052 /* Probe ports */ 2053 pmz_probe(); 2054 2055 /* TODO: Autoprobe console based on OF */ 2056 /* pmz_console.index = i; */ 2057 register_console(&pmz_console); 2058 2059 return 0; 2060 2061 } 2062 console_initcall(pmz_console_init); 2063 #endif /* CONFIG_SERIAL_PMACZILOG_CONSOLE */ 2064 2065 module_init(init_pmz); 2066 module_exit(exit_pmz); 2067