1 // SPDX-License-Identifier: GPL-2.0 2 /* 3 *Copyright (C) 2011 LAPIS Semiconductor Co., Ltd. 4 */ 5 #include <linux/kernel.h> 6 #include <linux/serial_reg.h> 7 #include <linux/slab.h> 8 #include <linux/module.h> 9 #include <linux/pci.h> 10 #include <linux/console.h> 11 #include <linux/serial_core.h> 12 #include <linux/tty.h> 13 #include <linux/tty_flip.h> 14 #include <linux/interrupt.h> 15 #include <linux/io.h> 16 #include <linux/dmi.h> 17 #include <linux/nmi.h> 18 #include <linux/delay.h> 19 #include <linux/of.h> 20 21 #include <linux/debugfs.h> 22 #include <linux/dmaengine.h> 23 #include <linux/pch_dma.h> 24 25 enum { 26 PCH_UART_HANDLED_RX_INT_SHIFT, 27 PCH_UART_HANDLED_TX_INT_SHIFT, 28 PCH_UART_HANDLED_RX_ERR_INT_SHIFT, 29 PCH_UART_HANDLED_RX_TRG_INT_SHIFT, 30 PCH_UART_HANDLED_MS_INT_SHIFT, 31 PCH_UART_HANDLED_LS_INT_SHIFT, 32 }; 33 34 #define PCH_UART_DRIVER_DEVICE "ttyPCH" 35 36 /* Set the max number of UART port 37 * Intel EG20T PCH: 4 port 38 * LAPIS Semiconductor ML7213 IOH: 3 port 39 * LAPIS Semiconductor ML7223 IOH: 2 port 40 */ 41 #define PCH_UART_NR 4 42 43 #define PCH_UART_HANDLED_RX_INT (1<<((PCH_UART_HANDLED_RX_INT_SHIFT)<<1)) 44 #define PCH_UART_HANDLED_TX_INT (1<<((PCH_UART_HANDLED_TX_INT_SHIFT)<<1)) 45 #define PCH_UART_HANDLED_RX_ERR_INT (1<<((\ 46 PCH_UART_HANDLED_RX_ERR_INT_SHIFT)<<1)) 47 #define PCH_UART_HANDLED_RX_TRG_INT (1<<((\ 48 PCH_UART_HANDLED_RX_TRG_INT_SHIFT)<<1)) 49 #define PCH_UART_HANDLED_MS_INT (1<<((PCH_UART_HANDLED_MS_INT_SHIFT)<<1)) 50 51 #define PCH_UART_HANDLED_LS_INT (1<<((PCH_UART_HANDLED_LS_INT_SHIFT)<<1)) 52 53 #define PCH_UART_RBR 0x00 54 #define PCH_UART_THR 0x00 55 56 #define PCH_UART_IER_MASK (PCH_UART_IER_ERBFI|PCH_UART_IER_ETBEI|\ 57 PCH_UART_IER_ELSI|PCH_UART_IER_EDSSI) 58 #define PCH_UART_IER_ERBFI 0x00000001 59 #define PCH_UART_IER_ETBEI 0x00000002 60 #define PCH_UART_IER_ELSI 0x00000004 61 #define PCH_UART_IER_EDSSI 0x00000008 62 63 #define PCH_UART_IIR_IP 0x00000001 64 #define PCH_UART_IIR_IID 0x00000006 65 #define PCH_UART_IIR_MSI 0x00000000 66 #define PCH_UART_IIR_TRI 0x00000002 67 #define PCH_UART_IIR_RRI 0x00000004 68 #define PCH_UART_IIR_REI 0x00000006 69 #define PCH_UART_IIR_TOI 0x00000008 70 #define PCH_UART_IIR_FIFO256 0x00000020 71 #define PCH_UART_IIR_FIFO64 PCH_UART_IIR_FIFO256 72 #define PCH_UART_IIR_FE 0x000000C0 73 74 #define PCH_UART_FCR_FIFOE 0x00000001 75 #define PCH_UART_FCR_RFR 0x00000002 76 #define PCH_UART_FCR_TFR 0x00000004 77 #define PCH_UART_FCR_DMS 0x00000008 78 #define PCH_UART_FCR_FIFO256 0x00000020 79 #define PCH_UART_FCR_RFTL 0x000000C0 80 81 #define PCH_UART_FCR_RFTL1 0x00000000 82 #define PCH_UART_FCR_RFTL64 0x00000040 83 #define PCH_UART_FCR_RFTL128 0x00000080 84 #define PCH_UART_FCR_RFTL224 0x000000C0 85 #define PCH_UART_FCR_RFTL16 PCH_UART_FCR_RFTL64 86 #define PCH_UART_FCR_RFTL32 PCH_UART_FCR_RFTL128 87 #define PCH_UART_FCR_RFTL56 PCH_UART_FCR_RFTL224 88 #define PCH_UART_FCR_RFTL4 PCH_UART_FCR_RFTL64 89 #define PCH_UART_FCR_RFTL8 PCH_UART_FCR_RFTL128 90 #define PCH_UART_FCR_RFTL14 PCH_UART_FCR_RFTL224 91 #define PCH_UART_FCR_RFTL_SHIFT 6 92 93 #define PCH_UART_LCR_WLS 0x00000003 94 #define PCH_UART_LCR_STB 0x00000004 95 #define PCH_UART_LCR_PEN 0x00000008 96 #define PCH_UART_LCR_EPS 0x00000010 97 #define PCH_UART_LCR_SP 0x00000020 98 #define PCH_UART_LCR_SB 0x00000040 99 #define PCH_UART_LCR_DLAB 0x00000080 100 #define PCH_UART_LCR_NP 0x00000000 101 #define PCH_UART_LCR_OP PCH_UART_LCR_PEN 102 #define PCH_UART_LCR_EP (PCH_UART_LCR_PEN | PCH_UART_LCR_EPS) 103 #define PCH_UART_LCR_1P (PCH_UART_LCR_PEN | PCH_UART_LCR_SP) 104 #define PCH_UART_LCR_0P (PCH_UART_LCR_PEN | PCH_UART_LCR_EPS |\ 105 PCH_UART_LCR_SP) 106 107 #define PCH_UART_LCR_5BIT 0x00000000 108 #define PCH_UART_LCR_6BIT 0x00000001 109 #define PCH_UART_LCR_7BIT 0x00000002 110 #define PCH_UART_LCR_8BIT 0x00000003 111 112 #define PCH_UART_MCR_DTR 0x00000001 113 #define PCH_UART_MCR_RTS 0x00000002 114 #define PCH_UART_MCR_OUT 0x0000000C 115 #define PCH_UART_MCR_LOOP 0x00000010 116 #define PCH_UART_MCR_AFE 0x00000020 117 118 #define PCH_UART_LSR_DR 0x00000001 119 #define PCH_UART_LSR_ERR (1<<7) 120 121 #define PCH_UART_MSR_DCTS 0x00000001 122 #define PCH_UART_MSR_DDSR 0x00000002 123 #define PCH_UART_MSR_TERI 0x00000004 124 #define PCH_UART_MSR_DDCD 0x00000008 125 #define PCH_UART_MSR_CTS 0x00000010 126 #define PCH_UART_MSR_DSR 0x00000020 127 #define PCH_UART_MSR_RI 0x00000040 128 #define PCH_UART_MSR_DCD 0x00000080 129 #define PCH_UART_MSR_DELTA (PCH_UART_MSR_DCTS | PCH_UART_MSR_DDSR |\ 130 PCH_UART_MSR_TERI | PCH_UART_MSR_DDCD) 131 132 #define PCH_UART_DLL 0x00 133 #define PCH_UART_DLM 0x01 134 135 #define PCH_UART_BRCSR 0x0E 136 137 #define PCH_UART_IID_RLS (PCH_UART_IIR_REI) 138 #define PCH_UART_IID_RDR (PCH_UART_IIR_RRI) 139 #define PCH_UART_IID_RDR_TO (PCH_UART_IIR_RRI | PCH_UART_IIR_TOI) 140 #define PCH_UART_IID_THRE (PCH_UART_IIR_TRI) 141 #define PCH_UART_IID_MS (PCH_UART_IIR_MSI) 142 143 #define PCH_UART_HAL_PARITY_NONE (PCH_UART_LCR_NP) 144 #define PCH_UART_HAL_PARITY_ODD (PCH_UART_LCR_OP) 145 #define PCH_UART_HAL_PARITY_EVEN (PCH_UART_LCR_EP) 146 #define PCH_UART_HAL_PARITY_FIX1 (PCH_UART_LCR_1P) 147 #define PCH_UART_HAL_PARITY_FIX0 (PCH_UART_LCR_0P) 148 #define PCH_UART_HAL_5BIT (PCH_UART_LCR_5BIT) 149 #define PCH_UART_HAL_6BIT (PCH_UART_LCR_6BIT) 150 #define PCH_UART_HAL_7BIT (PCH_UART_LCR_7BIT) 151 #define PCH_UART_HAL_8BIT (PCH_UART_LCR_8BIT) 152 #define PCH_UART_HAL_STB1 0 153 #define PCH_UART_HAL_STB2 (PCH_UART_LCR_STB) 154 155 #define PCH_UART_HAL_CLR_TX_FIFO (PCH_UART_FCR_TFR) 156 #define PCH_UART_HAL_CLR_RX_FIFO (PCH_UART_FCR_RFR) 157 #define PCH_UART_HAL_CLR_ALL_FIFO (PCH_UART_HAL_CLR_TX_FIFO | \ 158 PCH_UART_HAL_CLR_RX_FIFO) 159 160 #define PCH_UART_HAL_DMA_MODE0 0 161 #define PCH_UART_HAL_FIFO_DIS 0 162 #define PCH_UART_HAL_FIFO16 (PCH_UART_FCR_FIFOE) 163 #define PCH_UART_HAL_FIFO256 (PCH_UART_FCR_FIFOE | \ 164 PCH_UART_FCR_FIFO256) 165 #define PCH_UART_HAL_FIFO64 (PCH_UART_HAL_FIFO256) 166 #define PCH_UART_HAL_TRIGGER1 (PCH_UART_FCR_RFTL1) 167 #define PCH_UART_HAL_TRIGGER64 (PCH_UART_FCR_RFTL64) 168 #define PCH_UART_HAL_TRIGGER128 (PCH_UART_FCR_RFTL128) 169 #define PCH_UART_HAL_TRIGGER224 (PCH_UART_FCR_RFTL224) 170 #define PCH_UART_HAL_TRIGGER16 (PCH_UART_FCR_RFTL16) 171 #define PCH_UART_HAL_TRIGGER32 (PCH_UART_FCR_RFTL32) 172 #define PCH_UART_HAL_TRIGGER56 (PCH_UART_FCR_RFTL56) 173 #define PCH_UART_HAL_TRIGGER4 (PCH_UART_FCR_RFTL4) 174 #define PCH_UART_HAL_TRIGGER8 (PCH_UART_FCR_RFTL8) 175 #define PCH_UART_HAL_TRIGGER14 (PCH_UART_FCR_RFTL14) 176 #define PCH_UART_HAL_TRIGGER_L (PCH_UART_FCR_RFTL64) 177 #define PCH_UART_HAL_TRIGGER_M (PCH_UART_FCR_RFTL128) 178 #define PCH_UART_HAL_TRIGGER_H (PCH_UART_FCR_RFTL224) 179 180 #define PCH_UART_HAL_RX_INT (PCH_UART_IER_ERBFI) 181 #define PCH_UART_HAL_TX_INT (PCH_UART_IER_ETBEI) 182 #define PCH_UART_HAL_RX_ERR_INT (PCH_UART_IER_ELSI) 183 #define PCH_UART_HAL_MS_INT (PCH_UART_IER_EDSSI) 184 #define PCH_UART_HAL_ALL_INT (PCH_UART_IER_MASK) 185 186 #define PCH_UART_HAL_DTR (PCH_UART_MCR_DTR) 187 #define PCH_UART_HAL_RTS (PCH_UART_MCR_RTS) 188 #define PCH_UART_HAL_OUT (PCH_UART_MCR_OUT) 189 #define PCH_UART_HAL_LOOP (PCH_UART_MCR_LOOP) 190 #define PCH_UART_HAL_AFE (PCH_UART_MCR_AFE) 191 192 #define BOTH_EMPTY (UART_LSR_TEMT | UART_LSR_THRE) 193 194 #define DEFAULT_UARTCLK 1843200 /* 1.8432 MHz */ 195 #define CMITC_UARTCLK 192000000 /* 192.0000 MHz */ 196 #define FRI2_64_UARTCLK 64000000 /* 64.0000 MHz */ 197 #define FRI2_48_UARTCLK 48000000 /* 48.0000 MHz */ 198 #define NTC1_UARTCLK 64000000 /* 64.0000 MHz */ 199 #define MINNOW_UARTCLK 50000000 /* 50.0000 MHz */ 200 201 struct pch_uart_buffer { 202 unsigned char *buf; 203 int size; 204 }; 205 206 struct eg20t_port { 207 struct uart_port port; 208 int port_type; 209 void __iomem *membase; 210 resource_size_t mapbase; 211 unsigned int iobase; 212 struct pci_dev *pdev; 213 int fifo_size; 214 unsigned int uartclk; 215 int start_tx; 216 int start_rx; 217 int tx_empty; 218 int trigger; 219 int trigger_level; 220 struct pch_uart_buffer rxbuf; 221 unsigned int dmsr; 222 unsigned int fcr; 223 unsigned int mcr; 224 unsigned int use_dma; 225 struct dma_async_tx_descriptor *desc_tx; 226 struct dma_async_tx_descriptor *desc_rx; 227 struct pch_dma_slave param_tx; 228 struct pch_dma_slave param_rx; 229 struct dma_chan *chan_tx; 230 struct dma_chan *chan_rx; 231 struct scatterlist *sg_tx_p; 232 int nent; 233 int orig_nent; 234 struct scatterlist sg_rx; 235 int tx_dma_use; 236 void *rx_buf_virt; 237 dma_addr_t rx_buf_dma; 238 239 struct dentry *debugfs; 240 #define IRQ_NAME_SIZE 17 241 char irq_name[IRQ_NAME_SIZE]; 242 243 /* protect the eg20t_port private structure and io access to membase */ 244 spinlock_t lock; 245 }; 246 247 /** 248 * struct pch_uart_driver_data - private data structure for UART-DMA 249 * @port_type: The type of UART port 250 * @line_no: UART port line number (0, 1, 2...) 251 */ 252 struct pch_uart_driver_data { 253 int port_type; 254 int line_no; 255 }; 256 257 enum pch_uart_num_t { 258 pch_et20t_uart0 = 0, 259 pch_et20t_uart1, 260 pch_et20t_uart2, 261 pch_et20t_uart3, 262 pch_ml7213_uart0, 263 pch_ml7213_uart1, 264 pch_ml7213_uart2, 265 pch_ml7223_uart0, 266 pch_ml7223_uart1, 267 pch_ml7831_uart0, 268 pch_ml7831_uart1, 269 }; 270 271 static struct pch_uart_driver_data drv_dat[] = { 272 [pch_et20t_uart0] = {PORT_PCH_8LINE, 0}, 273 [pch_et20t_uart1] = {PORT_PCH_2LINE, 1}, 274 [pch_et20t_uart2] = {PORT_PCH_2LINE, 2}, 275 [pch_et20t_uart3] = {PORT_PCH_2LINE, 3}, 276 [pch_ml7213_uart0] = {PORT_PCH_8LINE, 0}, 277 [pch_ml7213_uart1] = {PORT_PCH_2LINE, 1}, 278 [pch_ml7213_uart2] = {PORT_PCH_2LINE, 2}, 279 [pch_ml7223_uart0] = {PORT_PCH_8LINE, 0}, 280 [pch_ml7223_uart1] = {PORT_PCH_2LINE, 1}, 281 [pch_ml7831_uart0] = {PORT_PCH_8LINE, 0}, 282 [pch_ml7831_uart1] = {PORT_PCH_2LINE, 1}, 283 }; 284 285 #ifdef CONFIG_SERIAL_PCH_UART_CONSOLE 286 static struct eg20t_port *pch_uart_ports[PCH_UART_NR]; 287 #endif 288 static unsigned int default_baud = 9600; 289 static unsigned int user_uartclk = 0; 290 static const int trigger_level_256[4] = { 1, 64, 128, 224 }; 291 static const int trigger_level_64[4] = { 1, 16, 32, 56 }; 292 static const int trigger_level_16[4] = { 1, 4, 8, 14 }; 293 static const int trigger_level_1[4] = { 1, 1, 1, 1 }; 294 295 #ifdef CONFIG_DEBUG_FS 296 297 #define PCH_REGS_BUFSIZE 1024 298 299 300 static ssize_t port_show_regs(struct file *file, char __user *user_buf, 301 size_t count, loff_t *ppos) 302 { 303 struct eg20t_port *priv = file->private_data; 304 char *buf; 305 u32 len = 0; 306 ssize_t ret; 307 unsigned char lcr; 308 309 buf = kzalloc(PCH_REGS_BUFSIZE, GFP_KERNEL); 310 if (!buf) 311 return 0; 312 313 len += scnprintf(buf + len, PCH_REGS_BUFSIZE - len, 314 "PCH EG20T port[%d] regs:\n", priv->port.line); 315 316 len += scnprintf(buf + len, PCH_REGS_BUFSIZE - len, 317 "=================================\n"); 318 len += scnprintf(buf + len, PCH_REGS_BUFSIZE - len, 319 "IER: \t0x%02x\n", ioread8(priv->membase + UART_IER)); 320 len += scnprintf(buf + len, PCH_REGS_BUFSIZE - len, 321 "IIR: \t0x%02x\n", ioread8(priv->membase + UART_IIR)); 322 len += scnprintf(buf + len, PCH_REGS_BUFSIZE - len, 323 "LCR: \t0x%02x\n", ioread8(priv->membase + UART_LCR)); 324 len += scnprintf(buf + len, PCH_REGS_BUFSIZE - len, 325 "MCR: \t0x%02x\n", ioread8(priv->membase + UART_MCR)); 326 len += scnprintf(buf + len, PCH_REGS_BUFSIZE - len, 327 "LSR: \t0x%02x\n", ioread8(priv->membase + UART_LSR)); 328 len += scnprintf(buf + len, PCH_REGS_BUFSIZE - len, 329 "MSR: \t0x%02x\n", ioread8(priv->membase + UART_MSR)); 330 len += scnprintf(buf + len, PCH_REGS_BUFSIZE - len, 331 "BRCSR: \t0x%02x\n", 332 ioread8(priv->membase + PCH_UART_BRCSR)); 333 334 lcr = ioread8(priv->membase + UART_LCR); 335 iowrite8(PCH_UART_LCR_DLAB, priv->membase + UART_LCR); 336 len += scnprintf(buf + len, PCH_REGS_BUFSIZE - len, 337 "DLL: \t0x%02x\n", ioread8(priv->membase + UART_DLL)); 338 len += scnprintf(buf + len, PCH_REGS_BUFSIZE - len, 339 "DLM: \t0x%02x\n", ioread8(priv->membase + UART_DLM)); 340 iowrite8(lcr, priv->membase + UART_LCR); 341 342 if (len > PCH_REGS_BUFSIZE) 343 len = PCH_REGS_BUFSIZE; 344 345 ret = simple_read_from_buffer(user_buf, count, ppos, buf, len); 346 kfree(buf); 347 return ret; 348 } 349 350 static const struct file_operations port_regs_ops = { 351 .owner = THIS_MODULE, 352 .open = simple_open, 353 .read = port_show_regs, 354 .llseek = default_llseek, 355 }; 356 #endif /* CONFIG_DEBUG_FS */ 357 358 static const struct dmi_system_id pch_uart_dmi_table[] = { 359 { 360 .ident = "CM-iTC", 361 { 362 DMI_MATCH(DMI_BOARD_NAME, "CM-iTC"), 363 }, 364 (void *)CMITC_UARTCLK, 365 }, 366 { 367 .ident = "FRI2", 368 { 369 DMI_MATCH(DMI_BIOS_VERSION, "FRI2"), 370 }, 371 (void *)FRI2_64_UARTCLK, 372 }, 373 { 374 .ident = "Fish River Island II", 375 { 376 DMI_MATCH(DMI_PRODUCT_NAME, "Fish River Island II"), 377 }, 378 (void *)FRI2_48_UARTCLK, 379 }, 380 { 381 .ident = "COMe-mTT", 382 { 383 DMI_MATCH(DMI_BOARD_NAME, "COMe-mTT"), 384 }, 385 (void *)NTC1_UARTCLK, 386 }, 387 { 388 .ident = "nanoETXexpress-TT", 389 { 390 DMI_MATCH(DMI_BOARD_NAME, "nanoETXexpress-TT"), 391 }, 392 (void *)NTC1_UARTCLK, 393 }, 394 { 395 .ident = "MinnowBoard", 396 { 397 DMI_MATCH(DMI_BOARD_NAME, "MinnowBoard"), 398 }, 399 (void *)MINNOW_UARTCLK, 400 }, 401 { } 402 }; 403 404 /* Return UART clock, checking for board specific clocks. */ 405 static unsigned int pch_uart_get_uartclk(void) 406 { 407 const struct dmi_system_id *d; 408 409 if (user_uartclk) 410 return user_uartclk; 411 412 d = dmi_first_match(pch_uart_dmi_table); 413 if (d) 414 return (unsigned long)d->driver_data; 415 416 return DEFAULT_UARTCLK; 417 } 418 419 static void pch_uart_hal_enable_interrupt(struct eg20t_port *priv, 420 unsigned int flag) 421 { 422 u8 ier = ioread8(priv->membase + UART_IER); 423 ier |= flag & PCH_UART_IER_MASK; 424 iowrite8(ier, priv->membase + UART_IER); 425 } 426 427 static void pch_uart_hal_disable_interrupt(struct eg20t_port *priv, 428 unsigned int flag) 429 { 430 u8 ier = ioread8(priv->membase + UART_IER); 431 ier &= ~(flag & PCH_UART_IER_MASK); 432 iowrite8(ier, priv->membase + UART_IER); 433 } 434 435 static int pch_uart_hal_set_line(struct eg20t_port *priv, unsigned int baud, 436 unsigned int parity, unsigned int bits, 437 unsigned int stb) 438 { 439 unsigned int dll, dlm, lcr; 440 int div; 441 442 div = DIV_ROUND_CLOSEST(priv->uartclk / 16, baud); 443 if (div < 0 || USHRT_MAX <= div) { 444 dev_err(priv->port.dev, "Invalid Baud(div=0x%x)\n", div); 445 return -EINVAL; 446 } 447 448 dll = (unsigned int)div & 0x00FFU; 449 dlm = ((unsigned int)div >> 8) & 0x00FFU; 450 451 if (parity & ~(PCH_UART_LCR_PEN | PCH_UART_LCR_EPS | PCH_UART_LCR_SP)) { 452 dev_err(priv->port.dev, "Invalid parity(0x%x)\n", parity); 453 return -EINVAL; 454 } 455 456 if (bits & ~PCH_UART_LCR_WLS) { 457 dev_err(priv->port.dev, "Invalid bits(0x%x)\n", bits); 458 return -EINVAL; 459 } 460 461 if (stb & ~PCH_UART_LCR_STB) { 462 dev_err(priv->port.dev, "Invalid STB(0x%x)\n", stb); 463 return -EINVAL; 464 } 465 466 lcr = parity; 467 lcr |= bits; 468 lcr |= stb; 469 470 dev_dbg(priv->port.dev, "%s:baud = %u, div = %04x, lcr = %02x (%lu)\n", 471 __func__, baud, div, lcr, jiffies); 472 iowrite8(PCH_UART_LCR_DLAB, priv->membase + UART_LCR); 473 iowrite8(dll, priv->membase + PCH_UART_DLL); 474 iowrite8(dlm, priv->membase + PCH_UART_DLM); 475 iowrite8(lcr, priv->membase + UART_LCR); 476 477 return 0; 478 } 479 480 static int pch_uart_hal_fifo_reset(struct eg20t_port *priv, 481 unsigned int flag) 482 { 483 if (flag & ~(PCH_UART_FCR_TFR | PCH_UART_FCR_RFR)) { 484 dev_err(priv->port.dev, "%s:Invalid flag(0x%x)\n", 485 __func__, flag); 486 return -EINVAL; 487 } 488 489 iowrite8(PCH_UART_FCR_FIFOE | priv->fcr, priv->membase + UART_FCR); 490 iowrite8(PCH_UART_FCR_FIFOE | priv->fcr | flag, 491 priv->membase + UART_FCR); 492 iowrite8(priv->fcr, priv->membase + UART_FCR); 493 494 return 0; 495 } 496 497 static int pch_uart_hal_set_fifo(struct eg20t_port *priv, 498 unsigned int dmamode, 499 unsigned int fifo_size, unsigned int trigger) 500 { 501 u8 fcr; 502 503 if (dmamode & ~PCH_UART_FCR_DMS) { 504 dev_err(priv->port.dev, "%s:Invalid DMA Mode(0x%x)\n", 505 __func__, dmamode); 506 return -EINVAL; 507 } 508 509 if (fifo_size & ~(PCH_UART_FCR_FIFOE | PCH_UART_FCR_FIFO256)) { 510 dev_err(priv->port.dev, "%s:Invalid FIFO SIZE(0x%x)\n", 511 __func__, fifo_size); 512 return -EINVAL; 513 } 514 515 if (trigger & ~PCH_UART_FCR_RFTL) { 516 dev_err(priv->port.dev, "%s:Invalid TRIGGER(0x%x)\n", 517 __func__, trigger); 518 return -EINVAL; 519 } 520 521 switch (priv->fifo_size) { 522 case 256: 523 priv->trigger_level = 524 trigger_level_256[trigger >> PCH_UART_FCR_RFTL_SHIFT]; 525 break; 526 case 64: 527 priv->trigger_level = 528 trigger_level_64[trigger >> PCH_UART_FCR_RFTL_SHIFT]; 529 break; 530 case 16: 531 priv->trigger_level = 532 trigger_level_16[trigger >> PCH_UART_FCR_RFTL_SHIFT]; 533 break; 534 default: 535 priv->trigger_level = 536 trigger_level_1[trigger >> PCH_UART_FCR_RFTL_SHIFT]; 537 break; 538 } 539 fcr = 540 dmamode | fifo_size | trigger | PCH_UART_FCR_RFR | PCH_UART_FCR_TFR; 541 iowrite8(PCH_UART_FCR_FIFOE, priv->membase + UART_FCR); 542 iowrite8(PCH_UART_FCR_FIFOE | PCH_UART_FCR_RFR | PCH_UART_FCR_TFR, 543 priv->membase + UART_FCR); 544 iowrite8(fcr, priv->membase + UART_FCR); 545 priv->fcr = fcr; 546 547 return 0; 548 } 549 550 static u8 pch_uart_hal_get_modem(struct eg20t_port *priv) 551 { 552 unsigned int msr = ioread8(priv->membase + UART_MSR); 553 priv->dmsr = msr & PCH_UART_MSR_DELTA; 554 return (u8)msr; 555 } 556 557 static void pch_uart_hal_write(struct eg20t_port *priv, 558 const unsigned char *buf, int tx_size) 559 { 560 int i; 561 unsigned int thr; 562 563 for (i = 0; i < tx_size;) { 564 thr = buf[i++]; 565 iowrite8(thr, priv->membase + PCH_UART_THR); 566 } 567 } 568 569 static int pch_uart_hal_read(struct eg20t_port *priv, unsigned char *buf, 570 int rx_size) 571 { 572 int i; 573 u8 rbr, lsr; 574 struct uart_port *port = &priv->port; 575 576 lsr = ioread8(priv->membase + UART_LSR); 577 for (i = 0, lsr = ioread8(priv->membase + UART_LSR); 578 i < rx_size && lsr & (UART_LSR_DR | UART_LSR_BI); 579 lsr = ioread8(priv->membase + UART_LSR)) { 580 rbr = ioread8(priv->membase + PCH_UART_RBR); 581 582 if (lsr & UART_LSR_BI) { 583 port->icount.brk++; 584 if (uart_handle_break(port)) 585 continue; 586 } 587 if (uart_handle_sysrq_char(port, rbr)) 588 continue; 589 590 buf[i++] = rbr; 591 } 592 return i; 593 } 594 595 static unsigned char pch_uart_hal_get_iid(struct eg20t_port *priv) 596 { 597 return ioread8(priv->membase + UART_IIR) &\ 598 (PCH_UART_IIR_IID | PCH_UART_IIR_TOI | PCH_UART_IIR_IP); 599 } 600 601 static u8 pch_uart_hal_get_line_status(struct eg20t_port *priv) 602 { 603 return ioread8(priv->membase + UART_LSR); 604 } 605 606 static void pch_uart_hal_set_break(struct eg20t_port *priv, int on) 607 { 608 unsigned int lcr; 609 610 lcr = ioread8(priv->membase + UART_LCR); 611 if (on) 612 lcr |= PCH_UART_LCR_SB; 613 else 614 lcr &= ~PCH_UART_LCR_SB; 615 616 iowrite8(lcr, priv->membase + UART_LCR); 617 } 618 619 static int push_rx(struct eg20t_port *priv, const unsigned char *buf, 620 int size) 621 { 622 struct uart_port *port = &priv->port; 623 struct tty_port *tport = &port->state->port; 624 625 tty_insert_flip_string(tport, buf, size); 626 tty_flip_buffer_push(tport); 627 628 return 0; 629 } 630 631 static int pop_tx_x(struct eg20t_port *priv, unsigned char *buf) 632 { 633 int ret = 0; 634 struct uart_port *port = &priv->port; 635 636 if (port->x_char) { 637 dev_dbg(priv->port.dev, "%s:X character send %02x (%lu)\n", 638 __func__, port->x_char, jiffies); 639 buf[0] = port->x_char; 640 port->x_char = 0; 641 ret = 1; 642 } 643 644 return ret; 645 } 646 647 static int dma_push_rx(struct eg20t_port *priv, int size) 648 { 649 int room; 650 struct uart_port *port = &priv->port; 651 struct tty_port *tport = &port->state->port; 652 653 room = tty_buffer_request_room(tport, size); 654 655 if (room < size) 656 dev_warn(port->dev, "Rx overrun: dropping %u bytes\n", 657 size - room); 658 if (!room) 659 return 0; 660 661 tty_insert_flip_string(tport, sg_virt(&priv->sg_rx), size); 662 663 port->icount.rx += room; 664 665 return room; 666 } 667 668 static void pch_free_dma(struct uart_port *port) 669 { 670 struct eg20t_port *priv; 671 priv = container_of(port, struct eg20t_port, port); 672 673 if (priv->chan_tx) { 674 dma_release_channel(priv->chan_tx); 675 priv->chan_tx = NULL; 676 } 677 if (priv->chan_rx) { 678 dma_release_channel(priv->chan_rx); 679 priv->chan_rx = NULL; 680 } 681 682 if (priv->rx_buf_dma) { 683 dma_free_coherent(port->dev, port->fifosize, priv->rx_buf_virt, 684 priv->rx_buf_dma); 685 priv->rx_buf_virt = NULL; 686 priv->rx_buf_dma = 0; 687 } 688 689 return; 690 } 691 692 static bool filter(struct dma_chan *chan, void *slave) 693 { 694 struct pch_dma_slave *param = slave; 695 696 if ((chan->chan_id == param->chan_id) && (param->dma_dev == 697 chan->device->dev)) { 698 chan->private = param; 699 return true; 700 } else { 701 return false; 702 } 703 } 704 705 static void pch_request_dma(struct uart_port *port) 706 { 707 dma_cap_mask_t mask; 708 struct dma_chan *chan; 709 struct pci_dev *dma_dev; 710 struct pch_dma_slave *param; 711 struct eg20t_port *priv = 712 container_of(port, struct eg20t_port, port); 713 dma_cap_zero(mask); 714 dma_cap_set(DMA_SLAVE, mask); 715 716 /* Get DMA's dev information */ 717 dma_dev = pci_get_slot(priv->pdev->bus, 718 PCI_DEVFN(PCI_SLOT(priv->pdev->devfn), 0)); 719 720 /* Set Tx DMA */ 721 param = &priv->param_tx; 722 param->dma_dev = &dma_dev->dev; 723 param->chan_id = priv->port.line * 2; /* Tx = 0, 2, 4, ... */ 724 725 param->tx_reg = port->mapbase + UART_TX; 726 chan = dma_request_channel(mask, filter, param); 727 if (!chan) { 728 dev_err(priv->port.dev, "%s:dma_request_channel FAILS(Tx)\n", 729 __func__); 730 return; 731 } 732 priv->chan_tx = chan; 733 734 /* Set Rx DMA */ 735 param = &priv->param_rx; 736 param->dma_dev = &dma_dev->dev; 737 param->chan_id = priv->port.line * 2 + 1; /* Rx = Tx + 1 */ 738 739 param->rx_reg = port->mapbase + UART_RX; 740 chan = dma_request_channel(mask, filter, param); 741 if (!chan) { 742 dev_err(priv->port.dev, "%s:dma_request_channel FAILS(Rx)\n", 743 __func__); 744 dma_release_channel(priv->chan_tx); 745 priv->chan_tx = NULL; 746 return; 747 } 748 749 /* Get Consistent memory for DMA */ 750 priv->rx_buf_virt = dma_alloc_coherent(port->dev, port->fifosize, 751 &priv->rx_buf_dma, GFP_KERNEL); 752 priv->chan_rx = chan; 753 } 754 755 static void pch_dma_rx_complete(void *arg) 756 { 757 struct eg20t_port *priv = arg; 758 struct uart_port *port = &priv->port; 759 int count; 760 761 dma_sync_sg_for_cpu(port->dev, &priv->sg_rx, 1, DMA_FROM_DEVICE); 762 count = dma_push_rx(priv, priv->trigger_level); 763 if (count) 764 tty_flip_buffer_push(&port->state->port); 765 async_tx_ack(priv->desc_rx); 766 pch_uart_hal_enable_interrupt(priv, PCH_UART_HAL_RX_INT | 767 PCH_UART_HAL_RX_ERR_INT); 768 } 769 770 static void pch_dma_tx_complete(void *arg) 771 { 772 struct eg20t_port *priv = arg; 773 struct uart_port *port = &priv->port; 774 struct circ_buf *xmit = &port->state->xmit; 775 struct scatterlist *sg = priv->sg_tx_p; 776 int i; 777 778 for (i = 0; i < priv->nent; i++, sg++) { 779 xmit->tail += sg_dma_len(sg); 780 port->icount.tx += sg_dma_len(sg); 781 } 782 xmit->tail &= UART_XMIT_SIZE - 1; 783 async_tx_ack(priv->desc_tx); 784 dma_unmap_sg(port->dev, sg, priv->orig_nent, DMA_TO_DEVICE); 785 priv->tx_dma_use = 0; 786 priv->nent = 0; 787 priv->orig_nent = 0; 788 kfree(priv->sg_tx_p); 789 pch_uart_hal_enable_interrupt(priv, PCH_UART_HAL_TX_INT); 790 } 791 792 static int pop_tx(struct eg20t_port *priv, int size) 793 { 794 int count = 0; 795 struct uart_port *port = &priv->port; 796 struct circ_buf *xmit = &port->state->xmit; 797 798 if (uart_tx_stopped(port) || uart_circ_empty(xmit) || count >= size) 799 goto pop_tx_end; 800 801 do { 802 int cnt_to_end = 803 CIRC_CNT_TO_END(xmit->head, xmit->tail, UART_XMIT_SIZE); 804 int sz = min(size - count, cnt_to_end); 805 pch_uart_hal_write(priv, &xmit->buf[xmit->tail], sz); 806 xmit->tail = (xmit->tail + sz) & (UART_XMIT_SIZE - 1); 807 count += sz; 808 } while (!uart_circ_empty(xmit) && count < size); 809 810 pop_tx_end: 811 dev_dbg(priv->port.dev, "%d characters. Remained %d characters.(%lu)\n", 812 count, size - count, jiffies); 813 814 return count; 815 } 816 817 static int handle_rx_to(struct eg20t_port *priv) 818 { 819 struct pch_uart_buffer *buf; 820 int rx_size; 821 int ret; 822 if (!priv->start_rx) { 823 pch_uart_hal_disable_interrupt(priv, PCH_UART_HAL_RX_INT | 824 PCH_UART_HAL_RX_ERR_INT); 825 return 0; 826 } 827 buf = &priv->rxbuf; 828 do { 829 rx_size = pch_uart_hal_read(priv, buf->buf, buf->size); 830 ret = push_rx(priv, buf->buf, rx_size); 831 if (ret) 832 return 0; 833 } while (rx_size == buf->size); 834 835 return PCH_UART_HANDLED_RX_INT; 836 } 837 838 static int handle_rx(struct eg20t_port *priv) 839 { 840 return handle_rx_to(priv); 841 } 842 843 static int dma_handle_rx(struct eg20t_port *priv) 844 { 845 struct uart_port *port = &priv->port; 846 struct dma_async_tx_descriptor *desc; 847 struct scatterlist *sg; 848 849 priv = container_of(port, struct eg20t_port, port); 850 sg = &priv->sg_rx; 851 852 sg_init_table(&priv->sg_rx, 1); /* Initialize SG table */ 853 854 sg_dma_len(sg) = priv->trigger_level; 855 856 sg_set_page(&priv->sg_rx, virt_to_page(priv->rx_buf_virt), 857 sg_dma_len(sg), offset_in_page(priv->rx_buf_virt)); 858 859 sg_dma_address(sg) = priv->rx_buf_dma; 860 861 desc = dmaengine_prep_slave_sg(priv->chan_rx, 862 sg, 1, DMA_DEV_TO_MEM, 863 DMA_PREP_INTERRUPT | DMA_CTRL_ACK); 864 865 if (!desc) 866 return 0; 867 868 priv->desc_rx = desc; 869 desc->callback = pch_dma_rx_complete; 870 desc->callback_param = priv; 871 desc->tx_submit(desc); 872 dma_async_issue_pending(priv->chan_rx); 873 874 return PCH_UART_HANDLED_RX_INT; 875 } 876 877 static unsigned int handle_tx(struct eg20t_port *priv) 878 { 879 struct uart_port *port = &priv->port; 880 struct circ_buf *xmit = &port->state->xmit; 881 int fifo_size; 882 int tx_size; 883 int size; 884 int tx_empty; 885 886 if (!priv->start_tx) { 887 dev_info(priv->port.dev, "%s:Tx isn't started. (%lu)\n", 888 __func__, jiffies); 889 pch_uart_hal_disable_interrupt(priv, PCH_UART_HAL_TX_INT); 890 priv->tx_empty = 1; 891 return 0; 892 } 893 894 fifo_size = max(priv->fifo_size, 1); 895 tx_empty = 1; 896 if (pop_tx_x(priv, xmit->buf)) { 897 pch_uart_hal_write(priv, xmit->buf, 1); 898 port->icount.tx++; 899 tx_empty = 0; 900 fifo_size--; 901 } 902 size = min(xmit->head - xmit->tail, fifo_size); 903 if (size < 0) 904 size = fifo_size; 905 906 tx_size = pop_tx(priv, size); 907 if (tx_size > 0) { 908 port->icount.tx += tx_size; 909 tx_empty = 0; 910 } 911 912 priv->tx_empty = tx_empty; 913 914 if (tx_empty) { 915 pch_uart_hal_disable_interrupt(priv, PCH_UART_HAL_TX_INT); 916 uart_write_wakeup(port); 917 } 918 919 return PCH_UART_HANDLED_TX_INT; 920 } 921 922 static unsigned int dma_handle_tx(struct eg20t_port *priv) 923 { 924 struct uart_port *port = &priv->port; 925 struct circ_buf *xmit = &port->state->xmit; 926 struct scatterlist *sg; 927 int nent; 928 int fifo_size; 929 struct dma_async_tx_descriptor *desc; 930 int num; 931 int i; 932 int bytes; 933 int size; 934 int rem; 935 936 if (!priv->start_tx) { 937 dev_info(priv->port.dev, "%s:Tx isn't started. (%lu)\n", 938 __func__, jiffies); 939 pch_uart_hal_disable_interrupt(priv, PCH_UART_HAL_TX_INT); 940 priv->tx_empty = 1; 941 return 0; 942 } 943 944 if (priv->tx_dma_use) { 945 dev_dbg(priv->port.dev, "%s:Tx is not completed. (%lu)\n", 946 __func__, jiffies); 947 pch_uart_hal_disable_interrupt(priv, PCH_UART_HAL_TX_INT); 948 priv->tx_empty = 1; 949 return 0; 950 } 951 952 fifo_size = max(priv->fifo_size, 1); 953 if (pop_tx_x(priv, xmit->buf)) { 954 pch_uart_hal_write(priv, xmit->buf, 1); 955 port->icount.tx++; 956 fifo_size--; 957 } 958 959 bytes = min((int)CIRC_CNT(xmit->head, xmit->tail, 960 UART_XMIT_SIZE), CIRC_CNT_TO_END(xmit->head, 961 xmit->tail, UART_XMIT_SIZE)); 962 if (!bytes) { 963 dev_dbg(priv->port.dev, "%s 0 bytes return\n", __func__); 964 pch_uart_hal_disable_interrupt(priv, PCH_UART_HAL_TX_INT); 965 uart_write_wakeup(port); 966 return 0; 967 } 968 969 if (bytes > fifo_size) { 970 num = bytes / fifo_size + 1; 971 size = fifo_size; 972 rem = bytes % fifo_size; 973 } else { 974 num = 1; 975 size = bytes; 976 rem = bytes; 977 } 978 979 dev_dbg(priv->port.dev, "%s num=%d size=%d rem=%d\n", 980 __func__, num, size, rem); 981 982 priv->tx_dma_use = 1; 983 984 priv->sg_tx_p = kcalloc(num, sizeof(struct scatterlist), GFP_ATOMIC); 985 if (!priv->sg_tx_p) { 986 dev_err(priv->port.dev, "%s:kzalloc Failed\n", __func__); 987 return 0; 988 } 989 990 sg_init_table(priv->sg_tx_p, num); /* Initialize SG table */ 991 sg = priv->sg_tx_p; 992 993 for (i = 0; i < num; i++, sg++) { 994 if (i == (num - 1)) 995 sg_set_page(sg, virt_to_page(xmit->buf), 996 rem, fifo_size * i); 997 else 998 sg_set_page(sg, virt_to_page(xmit->buf), 999 size, fifo_size * i); 1000 } 1001 1002 sg = priv->sg_tx_p; 1003 nent = dma_map_sg(port->dev, sg, num, DMA_TO_DEVICE); 1004 if (!nent) { 1005 dev_err(priv->port.dev, "%s:dma_map_sg Failed\n", __func__); 1006 return 0; 1007 } 1008 priv->orig_nent = num; 1009 priv->nent = nent; 1010 1011 for (i = 0; i < nent; i++, sg++) { 1012 sg->offset = (xmit->tail & (UART_XMIT_SIZE - 1)) + 1013 fifo_size * i; 1014 sg_dma_address(sg) = (sg_dma_address(sg) & 1015 ~(UART_XMIT_SIZE - 1)) + sg->offset; 1016 if (i == (nent - 1)) 1017 sg_dma_len(sg) = rem; 1018 else 1019 sg_dma_len(sg) = size; 1020 } 1021 1022 desc = dmaengine_prep_slave_sg(priv->chan_tx, 1023 priv->sg_tx_p, nent, DMA_MEM_TO_DEV, 1024 DMA_PREP_INTERRUPT | DMA_CTRL_ACK); 1025 if (!desc) { 1026 dev_err(priv->port.dev, "%s:dmaengine_prep_slave_sg Failed\n", 1027 __func__); 1028 return 0; 1029 } 1030 dma_sync_sg_for_device(port->dev, priv->sg_tx_p, nent, DMA_TO_DEVICE); 1031 priv->desc_tx = desc; 1032 desc->callback = pch_dma_tx_complete; 1033 desc->callback_param = priv; 1034 1035 desc->tx_submit(desc); 1036 1037 dma_async_issue_pending(priv->chan_tx); 1038 1039 return PCH_UART_HANDLED_TX_INT; 1040 } 1041 1042 static void pch_uart_err_ir(struct eg20t_port *priv, unsigned int lsr) 1043 { 1044 struct uart_port *port = &priv->port; 1045 struct tty_struct *tty = tty_port_tty_get(&port->state->port); 1046 char *error_msg[5] = {}; 1047 int i = 0; 1048 1049 if (lsr & PCH_UART_LSR_ERR) 1050 error_msg[i++] = "Error data in FIFO\n"; 1051 1052 if (lsr & UART_LSR_FE) { 1053 port->icount.frame++; 1054 error_msg[i++] = " Framing Error\n"; 1055 } 1056 1057 if (lsr & UART_LSR_PE) { 1058 port->icount.parity++; 1059 error_msg[i++] = " Parity Error\n"; 1060 } 1061 1062 if (lsr & UART_LSR_OE) { 1063 port->icount.overrun++; 1064 error_msg[i++] = " Overrun Error\n"; 1065 } 1066 1067 if (tty == NULL) { 1068 for (i = 0; error_msg[i] != NULL; i++) 1069 dev_err(&priv->pdev->dev, error_msg[i]); 1070 } else { 1071 tty_kref_put(tty); 1072 } 1073 } 1074 1075 static irqreturn_t pch_uart_interrupt(int irq, void *dev_id) 1076 { 1077 struct eg20t_port *priv = dev_id; 1078 unsigned int handled; 1079 u8 lsr; 1080 int ret = 0; 1081 unsigned char iid; 1082 unsigned long flags; 1083 int next = 1; 1084 u8 msr; 1085 1086 spin_lock_irqsave(&priv->lock, flags); 1087 handled = 0; 1088 while (next) { 1089 iid = pch_uart_hal_get_iid(priv); 1090 if (iid & PCH_UART_IIR_IP) /* No Interrupt */ 1091 break; 1092 switch (iid) { 1093 case PCH_UART_IID_RLS: /* Receiver Line Status */ 1094 lsr = pch_uart_hal_get_line_status(priv); 1095 if (lsr & (PCH_UART_LSR_ERR | UART_LSR_FE | 1096 UART_LSR_PE | UART_LSR_OE)) { 1097 pch_uart_err_ir(priv, lsr); 1098 ret = PCH_UART_HANDLED_RX_ERR_INT; 1099 } else { 1100 ret = PCH_UART_HANDLED_LS_INT; 1101 } 1102 break; 1103 case PCH_UART_IID_RDR: /* Received Data Ready */ 1104 if (priv->use_dma) { 1105 pch_uart_hal_disable_interrupt(priv, 1106 PCH_UART_HAL_RX_INT | 1107 PCH_UART_HAL_RX_ERR_INT); 1108 ret = dma_handle_rx(priv); 1109 if (!ret) 1110 pch_uart_hal_enable_interrupt(priv, 1111 PCH_UART_HAL_RX_INT | 1112 PCH_UART_HAL_RX_ERR_INT); 1113 } else { 1114 ret = handle_rx(priv); 1115 } 1116 break; 1117 case PCH_UART_IID_RDR_TO: /* Received Data Ready 1118 (FIFO Timeout) */ 1119 ret = handle_rx_to(priv); 1120 break; 1121 case PCH_UART_IID_THRE: /* Transmitter Holding Register 1122 Empty */ 1123 if (priv->use_dma) 1124 ret = dma_handle_tx(priv); 1125 else 1126 ret = handle_tx(priv); 1127 break; 1128 case PCH_UART_IID_MS: /* Modem Status */ 1129 msr = pch_uart_hal_get_modem(priv); 1130 next = 0; /* MS ir prioirty is the lowest. So, MS ir 1131 means final interrupt */ 1132 if ((msr & UART_MSR_ANY_DELTA) == 0) 1133 break; 1134 ret |= PCH_UART_HANDLED_MS_INT; 1135 break; 1136 default: /* Never junp to this label */ 1137 dev_err(priv->port.dev, "%s:iid=%02x (%lu)\n", __func__, 1138 iid, jiffies); 1139 ret = -1; 1140 next = 0; 1141 break; 1142 } 1143 handled |= (unsigned int)ret; 1144 } 1145 1146 spin_unlock_irqrestore(&priv->lock, flags); 1147 return IRQ_RETVAL(handled); 1148 } 1149 1150 /* This function tests whether the transmitter fifo and shifter for the port 1151 described by 'port' is empty. */ 1152 static unsigned int pch_uart_tx_empty(struct uart_port *port) 1153 { 1154 struct eg20t_port *priv; 1155 1156 priv = container_of(port, struct eg20t_port, port); 1157 if (priv->tx_empty) 1158 return TIOCSER_TEMT; 1159 else 1160 return 0; 1161 } 1162 1163 /* Returns the current state of modem control inputs. */ 1164 static unsigned int pch_uart_get_mctrl(struct uart_port *port) 1165 { 1166 struct eg20t_port *priv; 1167 u8 modem; 1168 unsigned int ret = 0; 1169 1170 priv = container_of(port, struct eg20t_port, port); 1171 modem = pch_uart_hal_get_modem(priv); 1172 1173 if (modem & UART_MSR_DCD) 1174 ret |= TIOCM_CAR; 1175 1176 if (modem & UART_MSR_RI) 1177 ret |= TIOCM_RNG; 1178 1179 if (modem & UART_MSR_DSR) 1180 ret |= TIOCM_DSR; 1181 1182 if (modem & UART_MSR_CTS) 1183 ret |= TIOCM_CTS; 1184 1185 return ret; 1186 } 1187 1188 static void pch_uart_set_mctrl(struct uart_port *port, unsigned int mctrl) 1189 { 1190 u32 mcr = 0; 1191 struct eg20t_port *priv = container_of(port, struct eg20t_port, port); 1192 1193 if (mctrl & TIOCM_DTR) 1194 mcr |= UART_MCR_DTR; 1195 if (mctrl & TIOCM_RTS) 1196 mcr |= UART_MCR_RTS; 1197 if (mctrl & TIOCM_LOOP) 1198 mcr |= UART_MCR_LOOP; 1199 1200 if (priv->mcr & UART_MCR_AFE) 1201 mcr |= UART_MCR_AFE; 1202 1203 if (mctrl) 1204 iowrite8(mcr, priv->membase + UART_MCR); 1205 } 1206 1207 static void pch_uart_stop_tx(struct uart_port *port) 1208 { 1209 struct eg20t_port *priv; 1210 priv = container_of(port, struct eg20t_port, port); 1211 priv->start_tx = 0; 1212 priv->tx_dma_use = 0; 1213 } 1214 1215 static void pch_uart_start_tx(struct uart_port *port) 1216 { 1217 struct eg20t_port *priv; 1218 1219 priv = container_of(port, struct eg20t_port, port); 1220 1221 if (priv->use_dma) { 1222 if (priv->tx_dma_use) { 1223 dev_dbg(priv->port.dev, "%s : Tx DMA is NOT empty.\n", 1224 __func__); 1225 return; 1226 } 1227 } 1228 1229 priv->start_tx = 1; 1230 pch_uart_hal_enable_interrupt(priv, PCH_UART_HAL_TX_INT); 1231 } 1232 1233 static void pch_uart_stop_rx(struct uart_port *port) 1234 { 1235 struct eg20t_port *priv; 1236 priv = container_of(port, struct eg20t_port, port); 1237 priv->start_rx = 0; 1238 pch_uart_hal_disable_interrupt(priv, PCH_UART_HAL_RX_INT | 1239 PCH_UART_HAL_RX_ERR_INT); 1240 } 1241 1242 /* Enable the modem status interrupts. */ 1243 static void pch_uart_enable_ms(struct uart_port *port) 1244 { 1245 struct eg20t_port *priv; 1246 priv = container_of(port, struct eg20t_port, port); 1247 pch_uart_hal_enable_interrupt(priv, PCH_UART_HAL_MS_INT); 1248 } 1249 1250 /* Control the transmission of a break signal. */ 1251 static void pch_uart_break_ctl(struct uart_port *port, int ctl) 1252 { 1253 struct eg20t_port *priv; 1254 unsigned long flags; 1255 1256 priv = container_of(port, struct eg20t_port, port); 1257 spin_lock_irqsave(&priv->lock, flags); 1258 pch_uart_hal_set_break(priv, ctl); 1259 spin_unlock_irqrestore(&priv->lock, flags); 1260 } 1261 1262 /* Grab any interrupt resources and initialise any low level driver state. */ 1263 static int pch_uart_startup(struct uart_port *port) 1264 { 1265 struct eg20t_port *priv; 1266 int ret; 1267 int fifo_size; 1268 int trigger_level; 1269 1270 priv = container_of(port, struct eg20t_port, port); 1271 priv->tx_empty = 1; 1272 1273 if (port->uartclk) 1274 priv->uartclk = port->uartclk; 1275 else 1276 port->uartclk = priv->uartclk; 1277 1278 pch_uart_hal_disable_interrupt(priv, PCH_UART_HAL_ALL_INT); 1279 ret = pch_uart_hal_set_line(priv, default_baud, 1280 PCH_UART_HAL_PARITY_NONE, PCH_UART_HAL_8BIT, 1281 PCH_UART_HAL_STB1); 1282 if (ret) 1283 return ret; 1284 1285 switch (priv->fifo_size) { 1286 case 256: 1287 fifo_size = PCH_UART_HAL_FIFO256; 1288 break; 1289 case 64: 1290 fifo_size = PCH_UART_HAL_FIFO64; 1291 break; 1292 case 16: 1293 fifo_size = PCH_UART_HAL_FIFO16; 1294 break; 1295 case 1: 1296 default: 1297 fifo_size = PCH_UART_HAL_FIFO_DIS; 1298 break; 1299 } 1300 1301 switch (priv->trigger) { 1302 case PCH_UART_HAL_TRIGGER1: 1303 trigger_level = 1; 1304 break; 1305 case PCH_UART_HAL_TRIGGER_L: 1306 trigger_level = priv->fifo_size / 4; 1307 break; 1308 case PCH_UART_HAL_TRIGGER_M: 1309 trigger_level = priv->fifo_size / 2; 1310 break; 1311 case PCH_UART_HAL_TRIGGER_H: 1312 default: 1313 trigger_level = priv->fifo_size - (priv->fifo_size / 8); 1314 break; 1315 } 1316 1317 priv->trigger_level = trigger_level; 1318 ret = pch_uart_hal_set_fifo(priv, PCH_UART_HAL_DMA_MODE0, 1319 fifo_size, priv->trigger); 1320 if (ret < 0) 1321 return ret; 1322 1323 ret = request_irq(priv->port.irq, pch_uart_interrupt, IRQF_SHARED, 1324 priv->irq_name, priv); 1325 if (ret < 0) 1326 return ret; 1327 1328 if (priv->use_dma) 1329 pch_request_dma(port); 1330 1331 priv->start_rx = 1; 1332 pch_uart_hal_enable_interrupt(priv, PCH_UART_HAL_RX_INT | 1333 PCH_UART_HAL_RX_ERR_INT); 1334 uart_update_timeout(port, CS8, default_baud); 1335 1336 return 0; 1337 } 1338 1339 static void pch_uart_shutdown(struct uart_port *port) 1340 { 1341 struct eg20t_port *priv; 1342 int ret; 1343 1344 priv = container_of(port, struct eg20t_port, port); 1345 pch_uart_hal_disable_interrupt(priv, PCH_UART_HAL_ALL_INT); 1346 pch_uart_hal_fifo_reset(priv, PCH_UART_HAL_CLR_ALL_FIFO); 1347 ret = pch_uart_hal_set_fifo(priv, PCH_UART_HAL_DMA_MODE0, 1348 PCH_UART_HAL_FIFO_DIS, PCH_UART_HAL_TRIGGER1); 1349 if (ret) 1350 dev_err(priv->port.dev, 1351 "pch_uart_hal_set_fifo Failed(ret=%d)\n", ret); 1352 1353 pch_free_dma(port); 1354 1355 free_irq(priv->port.irq, priv); 1356 } 1357 1358 /* Change the port parameters, including word length, parity, stop 1359 *bits. Update read_status_mask and ignore_status_mask to indicate 1360 *the types of events we are interested in receiving. */ 1361 static void pch_uart_set_termios(struct uart_port *port, 1362 struct ktermios *termios, struct ktermios *old) 1363 { 1364 int rtn; 1365 unsigned int baud, parity, bits, stb; 1366 struct eg20t_port *priv; 1367 unsigned long flags; 1368 1369 priv = container_of(port, struct eg20t_port, port); 1370 switch (termios->c_cflag & CSIZE) { 1371 case CS5: 1372 bits = PCH_UART_HAL_5BIT; 1373 break; 1374 case CS6: 1375 bits = PCH_UART_HAL_6BIT; 1376 break; 1377 case CS7: 1378 bits = PCH_UART_HAL_7BIT; 1379 break; 1380 default: /* CS8 */ 1381 bits = PCH_UART_HAL_8BIT; 1382 break; 1383 } 1384 if (termios->c_cflag & CSTOPB) 1385 stb = PCH_UART_HAL_STB2; 1386 else 1387 stb = PCH_UART_HAL_STB1; 1388 1389 if (termios->c_cflag & PARENB) { 1390 if (termios->c_cflag & PARODD) 1391 parity = PCH_UART_HAL_PARITY_ODD; 1392 else 1393 parity = PCH_UART_HAL_PARITY_EVEN; 1394 1395 } else 1396 parity = PCH_UART_HAL_PARITY_NONE; 1397 1398 /* Only UART0 has auto hardware flow function */ 1399 if ((termios->c_cflag & CRTSCTS) && (priv->fifo_size == 256)) 1400 priv->mcr |= UART_MCR_AFE; 1401 else 1402 priv->mcr &= ~UART_MCR_AFE; 1403 1404 termios->c_cflag &= ~CMSPAR; /* Mark/Space parity is not supported */ 1405 1406 baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk / 16); 1407 1408 spin_lock_irqsave(&priv->lock, flags); 1409 spin_lock(&port->lock); 1410 1411 uart_update_timeout(port, termios->c_cflag, baud); 1412 rtn = pch_uart_hal_set_line(priv, baud, parity, bits, stb); 1413 if (rtn) 1414 goto out; 1415 1416 pch_uart_set_mctrl(&priv->port, priv->port.mctrl); 1417 /* Don't rewrite B0 */ 1418 if (tty_termios_baud_rate(termios)) 1419 tty_termios_encode_baud_rate(termios, baud, baud); 1420 1421 out: 1422 spin_unlock(&port->lock); 1423 spin_unlock_irqrestore(&priv->lock, flags); 1424 } 1425 1426 static const char *pch_uart_type(struct uart_port *port) 1427 { 1428 return KBUILD_MODNAME; 1429 } 1430 1431 static void pch_uart_release_port(struct uart_port *port) 1432 { 1433 struct eg20t_port *priv; 1434 1435 priv = container_of(port, struct eg20t_port, port); 1436 pci_iounmap(priv->pdev, priv->membase); 1437 pci_release_regions(priv->pdev); 1438 } 1439 1440 static int pch_uart_request_port(struct uart_port *port) 1441 { 1442 struct eg20t_port *priv; 1443 int ret; 1444 void __iomem *membase; 1445 1446 priv = container_of(port, struct eg20t_port, port); 1447 ret = pci_request_regions(priv->pdev, KBUILD_MODNAME); 1448 if (ret < 0) 1449 return -EBUSY; 1450 1451 membase = pci_iomap(priv->pdev, 1, 0); 1452 if (!membase) { 1453 pci_release_regions(priv->pdev); 1454 return -EBUSY; 1455 } 1456 priv->membase = port->membase = membase; 1457 1458 return 0; 1459 } 1460 1461 static void pch_uart_config_port(struct uart_port *port, int type) 1462 { 1463 struct eg20t_port *priv; 1464 1465 priv = container_of(port, struct eg20t_port, port); 1466 if (type & UART_CONFIG_TYPE) { 1467 port->type = priv->port_type; 1468 pch_uart_request_port(port); 1469 } 1470 } 1471 1472 static int pch_uart_verify_port(struct uart_port *port, 1473 struct serial_struct *serinfo) 1474 { 1475 struct eg20t_port *priv; 1476 1477 priv = container_of(port, struct eg20t_port, port); 1478 if (serinfo->flags & UPF_LOW_LATENCY) { 1479 dev_info(priv->port.dev, 1480 "PCH UART : Use PIO Mode (without DMA)\n"); 1481 priv->use_dma = 0; 1482 serinfo->flags &= ~UPF_LOW_LATENCY; 1483 } else { 1484 #ifndef CONFIG_PCH_DMA 1485 dev_err(priv->port.dev, "%s : PCH DMA is not Loaded.\n", 1486 __func__); 1487 return -EOPNOTSUPP; 1488 #endif 1489 if (!priv->use_dma) { 1490 pch_request_dma(port); 1491 if (priv->chan_rx) 1492 priv->use_dma = 1; 1493 } 1494 dev_info(priv->port.dev, "PCH UART: %s\n", 1495 priv->use_dma ? 1496 "Use DMA Mode" : "No DMA"); 1497 } 1498 1499 return 0; 1500 } 1501 1502 #if defined(CONFIG_CONSOLE_POLL) || defined(CONFIG_SERIAL_PCH_UART_CONSOLE) 1503 /* 1504 * Wait for transmitter & holding register to empty 1505 */ 1506 static void wait_for_xmitr(struct eg20t_port *up, int bits) 1507 { 1508 unsigned int status, tmout = 10000; 1509 1510 /* Wait up to 10ms for the character(s) to be sent. */ 1511 for (;;) { 1512 status = ioread8(up->membase + UART_LSR); 1513 1514 if ((status & bits) == bits) 1515 break; 1516 if (--tmout == 0) 1517 break; 1518 udelay(1); 1519 } 1520 1521 /* Wait up to 1s for flow control if necessary */ 1522 if (up->port.flags & UPF_CONS_FLOW) { 1523 unsigned int tmout; 1524 for (tmout = 1000000; tmout; tmout--) { 1525 unsigned int msr = ioread8(up->membase + UART_MSR); 1526 if (msr & UART_MSR_CTS) 1527 break; 1528 udelay(1); 1529 touch_nmi_watchdog(); 1530 } 1531 } 1532 } 1533 #endif /* CONFIG_CONSOLE_POLL || CONFIG_SERIAL_PCH_UART_CONSOLE */ 1534 1535 #ifdef CONFIG_CONSOLE_POLL 1536 /* 1537 * Console polling routines for communicate via uart while 1538 * in an interrupt or debug context. 1539 */ 1540 static int pch_uart_get_poll_char(struct uart_port *port) 1541 { 1542 struct eg20t_port *priv = 1543 container_of(port, struct eg20t_port, port); 1544 u8 lsr = ioread8(priv->membase + UART_LSR); 1545 1546 if (!(lsr & UART_LSR_DR)) 1547 return NO_POLL_CHAR; 1548 1549 return ioread8(priv->membase + PCH_UART_RBR); 1550 } 1551 1552 1553 static void pch_uart_put_poll_char(struct uart_port *port, 1554 unsigned char c) 1555 { 1556 unsigned int ier; 1557 struct eg20t_port *priv = 1558 container_of(port, struct eg20t_port, port); 1559 1560 /* 1561 * First save the IER then disable the interrupts 1562 */ 1563 ier = ioread8(priv->membase + UART_IER); 1564 pch_uart_hal_disable_interrupt(priv, PCH_UART_HAL_ALL_INT); 1565 1566 wait_for_xmitr(priv, UART_LSR_THRE); 1567 /* 1568 * Send the character out. 1569 */ 1570 iowrite8(c, priv->membase + PCH_UART_THR); 1571 1572 /* 1573 * Finally, wait for transmitter to become empty 1574 * and restore the IER 1575 */ 1576 wait_for_xmitr(priv, BOTH_EMPTY); 1577 iowrite8(ier, priv->membase + UART_IER); 1578 } 1579 #endif /* CONFIG_CONSOLE_POLL */ 1580 1581 static const struct uart_ops pch_uart_ops = { 1582 .tx_empty = pch_uart_tx_empty, 1583 .set_mctrl = pch_uart_set_mctrl, 1584 .get_mctrl = pch_uart_get_mctrl, 1585 .stop_tx = pch_uart_stop_tx, 1586 .start_tx = pch_uart_start_tx, 1587 .stop_rx = pch_uart_stop_rx, 1588 .enable_ms = pch_uart_enable_ms, 1589 .break_ctl = pch_uart_break_ctl, 1590 .startup = pch_uart_startup, 1591 .shutdown = pch_uart_shutdown, 1592 .set_termios = pch_uart_set_termios, 1593 /* .pm = pch_uart_pm, Not supported yet */ 1594 .type = pch_uart_type, 1595 .release_port = pch_uart_release_port, 1596 .request_port = pch_uart_request_port, 1597 .config_port = pch_uart_config_port, 1598 .verify_port = pch_uart_verify_port, 1599 #ifdef CONFIG_CONSOLE_POLL 1600 .poll_get_char = pch_uart_get_poll_char, 1601 .poll_put_char = pch_uart_put_poll_char, 1602 #endif 1603 }; 1604 1605 #ifdef CONFIG_SERIAL_PCH_UART_CONSOLE 1606 1607 static void pch_console_putchar(struct uart_port *port, int ch) 1608 { 1609 struct eg20t_port *priv = 1610 container_of(port, struct eg20t_port, port); 1611 1612 wait_for_xmitr(priv, UART_LSR_THRE); 1613 iowrite8(ch, priv->membase + PCH_UART_THR); 1614 } 1615 1616 /* 1617 * Print a string to the serial port trying not to disturb 1618 * any possible real use of the port... 1619 * 1620 * The console_lock must be held when we get here. 1621 */ 1622 static void 1623 pch_console_write(struct console *co, const char *s, unsigned int count) 1624 { 1625 struct eg20t_port *priv; 1626 unsigned long flags; 1627 int priv_locked = 1; 1628 int port_locked = 1; 1629 u8 ier; 1630 1631 priv = pch_uart_ports[co->index]; 1632 1633 touch_nmi_watchdog(); 1634 1635 local_irq_save(flags); 1636 if (priv->port.sysrq) { 1637 /* call to uart_handle_sysrq_char already took the priv lock */ 1638 priv_locked = 0; 1639 /* serial8250_handle_port() already took the port lock */ 1640 port_locked = 0; 1641 } else if (oops_in_progress) { 1642 priv_locked = spin_trylock(&priv->lock); 1643 port_locked = spin_trylock(&priv->port.lock); 1644 } else { 1645 spin_lock(&priv->lock); 1646 spin_lock(&priv->port.lock); 1647 } 1648 1649 /* 1650 * First save the IER then disable the interrupts 1651 */ 1652 ier = ioread8(priv->membase + UART_IER); 1653 1654 pch_uart_hal_disable_interrupt(priv, PCH_UART_HAL_ALL_INT); 1655 1656 uart_console_write(&priv->port, s, count, pch_console_putchar); 1657 1658 /* 1659 * Finally, wait for transmitter to become empty 1660 * and restore the IER 1661 */ 1662 wait_for_xmitr(priv, BOTH_EMPTY); 1663 iowrite8(ier, priv->membase + UART_IER); 1664 1665 if (port_locked) 1666 spin_unlock(&priv->port.lock); 1667 if (priv_locked) 1668 spin_unlock(&priv->lock); 1669 local_irq_restore(flags); 1670 } 1671 1672 static int __init pch_console_setup(struct console *co, char *options) 1673 { 1674 struct uart_port *port; 1675 int baud = default_baud; 1676 int bits = 8; 1677 int parity = 'n'; 1678 int flow = 'n'; 1679 1680 /* 1681 * Check whether an invalid uart number has been specified, and 1682 * if so, search for the first available port that does have 1683 * console support. 1684 */ 1685 if (co->index >= PCH_UART_NR) 1686 co->index = 0; 1687 port = &pch_uart_ports[co->index]->port; 1688 1689 if (!port || (!port->iobase && !port->membase)) 1690 return -ENODEV; 1691 1692 port->uartclk = pch_uart_get_uartclk(); 1693 1694 if (options) 1695 uart_parse_options(options, &baud, &parity, &bits, &flow); 1696 1697 return uart_set_options(port, co, baud, parity, bits, flow); 1698 } 1699 1700 static struct uart_driver pch_uart_driver; 1701 1702 static struct console pch_console = { 1703 .name = PCH_UART_DRIVER_DEVICE, 1704 .write = pch_console_write, 1705 .device = uart_console_device, 1706 .setup = pch_console_setup, 1707 .flags = CON_PRINTBUFFER | CON_ANYTIME, 1708 .index = -1, 1709 .data = &pch_uart_driver, 1710 }; 1711 1712 #define PCH_CONSOLE (&pch_console) 1713 #else 1714 #define PCH_CONSOLE NULL 1715 #endif /* CONFIG_SERIAL_PCH_UART_CONSOLE */ 1716 1717 static struct uart_driver pch_uart_driver = { 1718 .owner = THIS_MODULE, 1719 .driver_name = KBUILD_MODNAME, 1720 .dev_name = PCH_UART_DRIVER_DEVICE, 1721 .major = 0, 1722 .minor = 0, 1723 .nr = PCH_UART_NR, 1724 .cons = PCH_CONSOLE, 1725 }; 1726 1727 static struct eg20t_port *pch_uart_init_port(struct pci_dev *pdev, 1728 const struct pci_device_id *id) 1729 { 1730 struct eg20t_port *priv; 1731 int ret; 1732 unsigned int iobase; 1733 unsigned int mapbase; 1734 unsigned char *rxbuf; 1735 int fifosize; 1736 int port_type; 1737 struct pch_uart_driver_data *board; 1738 #ifdef CONFIG_DEBUG_FS 1739 char name[32]; /* for debugfs file name */ 1740 #endif 1741 1742 board = &drv_dat[id->driver_data]; 1743 port_type = board->port_type; 1744 1745 priv = kzalloc(sizeof(struct eg20t_port), GFP_KERNEL); 1746 if (priv == NULL) 1747 goto init_port_alloc_err; 1748 1749 rxbuf = (unsigned char *)__get_free_page(GFP_KERNEL); 1750 if (!rxbuf) 1751 goto init_port_free_txbuf; 1752 1753 switch (port_type) { 1754 case PORT_PCH_8LINE: 1755 fifosize = 256; /* EG20T/ML7213: UART0 */ 1756 break; 1757 case PORT_PCH_2LINE: 1758 fifosize = 64; /* EG20T:UART1~3 ML7213: UART1~2*/ 1759 break; 1760 default: 1761 dev_err(&pdev->dev, "Invalid Port Type(=%d)\n", port_type); 1762 goto init_port_hal_free; 1763 } 1764 1765 pci_enable_msi(pdev); 1766 pci_set_master(pdev); 1767 1768 spin_lock_init(&priv->lock); 1769 1770 iobase = pci_resource_start(pdev, 0); 1771 mapbase = pci_resource_start(pdev, 1); 1772 priv->mapbase = mapbase; 1773 priv->iobase = iobase; 1774 priv->pdev = pdev; 1775 priv->tx_empty = 1; 1776 priv->rxbuf.buf = rxbuf; 1777 priv->rxbuf.size = PAGE_SIZE; 1778 1779 priv->fifo_size = fifosize; 1780 priv->uartclk = pch_uart_get_uartclk(); 1781 priv->port_type = port_type; 1782 priv->port.dev = &pdev->dev; 1783 priv->port.iobase = iobase; 1784 priv->port.membase = NULL; 1785 priv->port.mapbase = mapbase; 1786 priv->port.irq = pdev->irq; 1787 priv->port.iotype = UPIO_PORT; 1788 priv->port.ops = &pch_uart_ops; 1789 priv->port.flags = UPF_BOOT_AUTOCONF; 1790 priv->port.fifosize = fifosize; 1791 priv->port.line = board->line_no; 1792 priv->port.has_sysrq = IS_ENABLED(CONFIG_SERIAL_PCH_UART_CONSOLE); 1793 priv->trigger = PCH_UART_HAL_TRIGGER_M; 1794 1795 snprintf(priv->irq_name, IRQ_NAME_SIZE, 1796 KBUILD_MODNAME ":" PCH_UART_DRIVER_DEVICE "%d", 1797 priv->port.line); 1798 1799 spin_lock_init(&priv->port.lock); 1800 1801 pci_set_drvdata(pdev, priv); 1802 priv->trigger_level = 1; 1803 priv->fcr = 0; 1804 1805 if (pdev->dev.of_node) 1806 of_property_read_u32(pdev->dev.of_node, "clock-frequency" 1807 , &user_uartclk); 1808 1809 #ifdef CONFIG_SERIAL_PCH_UART_CONSOLE 1810 pch_uart_ports[board->line_no] = priv; 1811 #endif 1812 ret = uart_add_one_port(&pch_uart_driver, &priv->port); 1813 if (ret < 0) 1814 goto init_port_hal_free; 1815 1816 #ifdef CONFIG_DEBUG_FS 1817 snprintf(name, sizeof(name), "uart%d_regs", board->line_no); 1818 priv->debugfs = debugfs_create_file(name, S_IFREG | S_IRUGO, 1819 NULL, priv, &port_regs_ops); 1820 #endif 1821 1822 return priv; 1823 1824 init_port_hal_free: 1825 #ifdef CONFIG_SERIAL_PCH_UART_CONSOLE 1826 pch_uart_ports[board->line_no] = NULL; 1827 #endif 1828 free_page((unsigned long)rxbuf); 1829 init_port_free_txbuf: 1830 kfree(priv); 1831 init_port_alloc_err: 1832 1833 return NULL; 1834 } 1835 1836 static void pch_uart_exit_port(struct eg20t_port *priv) 1837 { 1838 1839 #ifdef CONFIG_DEBUG_FS 1840 debugfs_remove(priv->debugfs); 1841 #endif 1842 uart_remove_one_port(&pch_uart_driver, &priv->port); 1843 free_page((unsigned long)priv->rxbuf.buf); 1844 } 1845 1846 static void pch_uart_pci_remove(struct pci_dev *pdev) 1847 { 1848 struct eg20t_port *priv = pci_get_drvdata(pdev); 1849 1850 pci_disable_msi(pdev); 1851 1852 #ifdef CONFIG_SERIAL_PCH_UART_CONSOLE 1853 pch_uart_ports[priv->port.line] = NULL; 1854 #endif 1855 pch_uart_exit_port(priv); 1856 pci_disable_device(pdev); 1857 kfree(priv); 1858 return; 1859 } 1860 1861 static int __maybe_unused pch_uart_pci_suspend(struct device *dev) 1862 { 1863 struct eg20t_port *priv = dev_get_drvdata(dev); 1864 1865 uart_suspend_port(&pch_uart_driver, &priv->port); 1866 1867 return 0; 1868 } 1869 1870 static int __maybe_unused pch_uart_pci_resume(struct device *dev) 1871 { 1872 struct eg20t_port *priv = dev_get_drvdata(dev); 1873 1874 uart_resume_port(&pch_uart_driver, &priv->port); 1875 1876 return 0; 1877 } 1878 1879 static const struct pci_device_id pch_uart_pci_id[] = { 1880 {PCI_DEVICE(PCI_VENDOR_ID_INTEL, 0x8811), 1881 .driver_data = pch_et20t_uart0}, 1882 {PCI_DEVICE(PCI_VENDOR_ID_INTEL, 0x8812), 1883 .driver_data = pch_et20t_uart1}, 1884 {PCI_DEVICE(PCI_VENDOR_ID_INTEL, 0x8813), 1885 .driver_data = pch_et20t_uart2}, 1886 {PCI_DEVICE(PCI_VENDOR_ID_INTEL, 0x8814), 1887 .driver_data = pch_et20t_uart3}, 1888 {PCI_DEVICE(PCI_VENDOR_ID_ROHM, 0x8027), 1889 .driver_data = pch_ml7213_uart0}, 1890 {PCI_DEVICE(PCI_VENDOR_ID_ROHM, 0x8028), 1891 .driver_data = pch_ml7213_uart1}, 1892 {PCI_DEVICE(PCI_VENDOR_ID_ROHM, 0x8029), 1893 .driver_data = pch_ml7213_uart2}, 1894 {PCI_DEVICE(PCI_VENDOR_ID_ROHM, 0x800C), 1895 .driver_data = pch_ml7223_uart0}, 1896 {PCI_DEVICE(PCI_VENDOR_ID_ROHM, 0x800D), 1897 .driver_data = pch_ml7223_uart1}, 1898 {PCI_DEVICE(PCI_VENDOR_ID_ROHM, 0x8811), 1899 .driver_data = pch_ml7831_uart0}, 1900 {PCI_DEVICE(PCI_VENDOR_ID_ROHM, 0x8812), 1901 .driver_data = pch_ml7831_uart1}, 1902 {0,}, 1903 }; 1904 1905 static int pch_uart_pci_probe(struct pci_dev *pdev, 1906 const struct pci_device_id *id) 1907 { 1908 int ret; 1909 struct eg20t_port *priv; 1910 1911 ret = pci_enable_device(pdev); 1912 if (ret < 0) 1913 goto probe_error; 1914 1915 priv = pch_uart_init_port(pdev, id); 1916 if (!priv) { 1917 ret = -EBUSY; 1918 goto probe_disable_device; 1919 } 1920 pci_set_drvdata(pdev, priv); 1921 1922 return ret; 1923 1924 probe_disable_device: 1925 pci_disable_msi(pdev); 1926 pci_disable_device(pdev); 1927 probe_error: 1928 return ret; 1929 } 1930 1931 static SIMPLE_DEV_PM_OPS(pch_uart_pci_pm_ops, 1932 pch_uart_pci_suspend, 1933 pch_uart_pci_resume); 1934 1935 static struct pci_driver pch_uart_pci_driver = { 1936 .name = "pch_uart", 1937 .id_table = pch_uart_pci_id, 1938 .probe = pch_uart_pci_probe, 1939 .remove = pch_uart_pci_remove, 1940 .driver.pm = &pch_uart_pci_pm_ops, 1941 }; 1942 1943 static int __init pch_uart_module_init(void) 1944 { 1945 int ret; 1946 1947 /* register as UART driver */ 1948 ret = uart_register_driver(&pch_uart_driver); 1949 if (ret < 0) 1950 return ret; 1951 1952 /* register as PCI driver */ 1953 ret = pci_register_driver(&pch_uart_pci_driver); 1954 if (ret < 0) 1955 uart_unregister_driver(&pch_uart_driver); 1956 1957 return ret; 1958 } 1959 module_init(pch_uart_module_init); 1960 1961 static void __exit pch_uart_module_exit(void) 1962 { 1963 pci_unregister_driver(&pch_uart_pci_driver); 1964 uart_unregister_driver(&pch_uart_driver); 1965 } 1966 module_exit(pch_uart_module_exit); 1967 1968 MODULE_LICENSE("GPL v2"); 1969 MODULE_DESCRIPTION("Intel EG20T PCH UART PCI Driver"); 1970 MODULE_DEVICE_TABLE(pci, pch_uart_pci_id); 1971 1972 module_param(default_baud, uint, S_IRUGO); 1973 MODULE_PARM_DESC(default_baud, 1974 "Default BAUD for initial driver state and console (default 9600)"); 1975 module_param(user_uartclk, uint, S_IRUGO); 1976 MODULE_PARM_DESC(user_uartclk, 1977 "Override UART default or board specific UART clock"); 1978