1 // SPDX-License-Identifier: GPL-2.0+ 2 /* 3 * Maxim (Dallas) MAX3107/8/9, MAX14830 serial driver 4 * 5 * Copyright (C) 2012-2016 Alexander Shiyan <shc_work@mail.ru> 6 * 7 * Based on max3100.c, by Christian Pellegrin <chripell@evolware.org> 8 * Based on max3110.c, by Feng Tang <feng.tang@intel.com> 9 * Based on max3107.c, by Aavamobile 10 */ 11 12 #include <linux/bitops.h> 13 #include <linux/clk.h> 14 #include <linux/delay.h> 15 #include <linux/device.h> 16 #include <linux/gpio/driver.h> 17 #include <linux/i2c.h> 18 #include <linux/module.h> 19 #include <linux/mod_devicetable.h> 20 #include <linux/property.h> 21 #include <linux/regmap.h> 22 #include <linux/serial_core.h> 23 #include <linux/serial.h> 24 #include <linux/tty.h> 25 #include <linux/tty_flip.h> 26 #include <linux/spi/spi.h> 27 #include <linux/uaccess.h> 28 29 #define MAX310X_NAME "max310x" 30 #define MAX310X_MAJOR 204 31 #define MAX310X_MINOR 209 32 #define MAX310X_UART_NRMAX 16 33 34 /* MAX310X register definitions */ 35 #define MAX310X_RHR_REG (0x00) /* RX FIFO */ 36 #define MAX310X_THR_REG (0x00) /* TX FIFO */ 37 #define MAX310X_IRQEN_REG (0x01) /* IRQ enable */ 38 #define MAX310X_IRQSTS_REG (0x02) /* IRQ status */ 39 #define MAX310X_LSR_IRQEN_REG (0x03) /* LSR IRQ enable */ 40 #define MAX310X_LSR_IRQSTS_REG (0x04) /* LSR IRQ status */ 41 #define MAX310X_REG_05 (0x05) 42 #define MAX310X_SPCHR_IRQEN_REG MAX310X_REG_05 /* Special char IRQ en */ 43 #define MAX310X_SPCHR_IRQSTS_REG (0x06) /* Special char IRQ status */ 44 #define MAX310X_STS_IRQEN_REG (0x07) /* Status IRQ enable */ 45 #define MAX310X_STS_IRQSTS_REG (0x08) /* Status IRQ status */ 46 #define MAX310X_MODE1_REG (0x09) /* MODE1 */ 47 #define MAX310X_MODE2_REG (0x0a) /* MODE2 */ 48 #define MAX310X_LCR_REG (0x0b) /* LCR */ 49 #define MAX310X_RXTO_REG (0x0c) /* RX timeout */ 50 #define MAX310X_HDPIXDELAY_REG (0x0d) /* Auto transceiver delays */ 51 #define MAX310X_IRDA_REG (0x0e) /* IRDA settings */ 52 #define MAX310X_FLOWLVL_REG (0x0f) /* Flow control levels */ 53 #define MAX310X_FIFOTRIGLVL_REG (0x10) /* FIFO IRQ trigger levels */ 54 #define MAX310X_TXFIFOLVL_REG (0x11) /* TX FIFO level */ 55 #define MAX310X_RXFIFOLVL_REG (0x12) /* RX FIFO level */ 56 #define MAX310X_FLOWCTRL_REG (0x13) /* Flow control */ 57 #define MAX310X_XON1_REG (0x14) /* XON1 character */ 58 #define MAX310X_XON2_REG (0x15) /* XON2 character */ 59 #define MAX310X_XOFF1_REG (0x16) /* XOFF1 character */ 60 #define MAX310X_XOFF2_REG (0x17) /* XOFF2 character */ 61 #define MAX310X_GPIOCFG_REG (0x18) /* GPIO config */ 62 #define MAX310X_GPIODATA_REG (0x19) /* GPIO data */ 63 #define MAX310X_PLLCFG_REG (0x1a) /* PLL config */ 64 #define MAX310X_BRGCFG_REG (0x1b) /* Baud rate generator conf */ 65 #define MAX310X_BRGDIVLSB_REG (0x1c) /* Baud rate divisor LSB */ 66 #define MAX310X_BRGDIVMSB_REG (0x1d) /* Baud rate divisor MSB */ 67 #define MAX310X_CLKSRC_REG (0x1e) /* Clock source */ 68 #define MAX310X_REG_1F (0x1f) 69 70 #define MAX310X_REVID_REG MAX310X_REG_1F /* Revision ID */ 71 72 #define MAX310X_GLOBALIRQ_REG MAX310X_REG_1F /* Global IRQ (RO) */ 73 #define MAX310X_GLOBALCMD_REG MAX310X_REG_1F /* Global Command (WO) */ 74 75 /* Extended registers */ 76 #define MAX310X_SPI_REVID_EXTREG MAX310X_REG_05 /* Revision ID */ 77 #define MAX310X_I2C_REVID_EXTREG (0x25) /* Revision ID */ 78 79 /* IRQ register bits */ 80 #define MAX310X_IRQ_LSR_BIT (1 << 0) /* LSR interrupt */ 81 #define MAX310X_IRQ_SPCHR_BIT (1 << 1) /* Special char interrupt */ 82 #define MAX310X_IRQ_STS_BIT (1 << 2) /* Status interrupt */ 83 #define MAX310X_IRQ_RXFIFO_BIT (1 << 3) /* RX FIFO interrupt */ 84 #define MAX310X_IRQ_TXFIFO_BIT (1 << 4) /* TX FIFO interrupt */ 85 #define MAX310X_IRQ_TXEMPTY_BIT (1 << 5) /* TX FIFO empty interrupt */ 86 #define MAX310X_IRQ_RXEMPTY_BIT (1 << 6) /* RX FIFO empty interrupt */ 87 #define MAX310X_IRQ_CTS_BIT (1 << 7) /* CTS interrupt */ 88 89 /* LSR register bits */ 90 #define MAX310X_LSR_RXTO_BIT (1 << 0) /* RX timeout */ 91 #define MAX310X_LSR_RXOVR_BIT (1 << 1) /* RX overrun */ 92 #define MAX310X_LSR_RXPAR_BIT (1 << 2) /* RX parity error */ 93 #define MAX310X_LSR_FRERR_BIT (1 << 3) /* Frame error */ 94 #define MAX310X_LSR_RXBRK_BIT (1 << 4) /* RX break */ 95 #define MAX310X_LSR_RXNOISE_BIT (1 << 5) /* RX noise */ 96 #define MAX310X_LSR_CTS_BIT (1 << 7) /* CTS pin state */ 97 98 /* Special character register bits */ 99 #define MAX310X_SPCHR_XON1_BIT (1 << 0) /* XON1 character */ 100 #define MAX310X_SPCHR_XON2_BIT (1 << 1) /* XON2 character */ 101 #define MAX310X_SPCHR_XOFF1_BIT (1 << 2) /* XOFF1 character */ 102 #define MAX310X_SPCHR_XOFF2_BIT (1 << 3) /* XOFF2 character */ 103 #define MAX310X_SPCHR_BREAK_BIT (1 << 4) /* RX break */ 104 #define MAX310X_SPCHR_MULTIDROP_BIT (1 << 5) /* 9-bit multidrop addr char */ 105 106 /* Status register bits */ 107 #define MAX310X_STS_GPIO0_BIT (1 << 0) /* GPIO 0 interrupt */ 108 #define MAX310X_STS_GPIO1_BIT (1 << 1) /* GPIO 1 interrupt */ 109 #define MAX310X_STS_GPIO2_BIT (1 << 2) /* GPIO 2 interrupt */ 110 #define MAX310X_STS_GPIO3_BIT (1 << 3) /* GPIO 3 interrupt */ 111 #define MAX310X_STS_CLKREADY_BIT (1 << 5) /* Clock ready */ 112 #define MAX310X_STS_SLEEP_BIT (1 << 6) /* Sleep interrupt */ 113 114 /* MODE1 register bits */ 115 #define MAX310X_MODE1_RXDIS_BIT (1 << 0) /* RX disable */ 116 #define MAX310X_MODE1_TXDIS_BIT (1 << 1) /* TX disable */ 117 #define MAX310X_MODE1_TXHIZ_BIT (1 << 2) /* TX pin three-state */ 118 #define MAX310X_MODE1_RTSHIZ_BIT (1 << 3) /* RTS pin three-state */ 119 #define MAX310X_MODE1_TRNSCVCTRL_BIT (1 << 4) /* Transceiver ctrl enable */ 120 #define MAX310X_MODE1_FORCESLEEP_BIT (1 << 5) /* Force sleep mode */ 121 #define MAX310X_MODE1_AUTOSLEEP_BIT (1 << 6) /* Auto sleep enable */ 122 #define MAX310X_MODE1_IRQSEL_BIT (1 << 7) /* IRQ pin enable */ 123 124 /* MODE2 register bits */ 125 #define MAX310X_MODE2_RST_BIT (1 << 0) /* Chip reset */ 126 #define MAX310X_MODE2_FIFORST_BIT (1 << 1) /* FIFO reset */ 127 #define MAX310X_MODE2_RXTRIGINV_BIT (1 << 2) /* RX FIFO INT invert */ 128 #define MAX310X_MODE2_RXEMPTINV_BIT (1 << 3) /* RX FIFO empty INT invert */ 129 #define MAX310X_MODE2_SPCHR_BIT (1 << 4) /* Special chr detect enable */ 130 #define MAX310X_MODE2_LOOPBACK_BIT (1 << 5) /* Internal loopback enable */ 131 #define MAX310X_MODE2_MULTIDROP_BIT (1 << 6) /* 9-bit multidrop enable */ 132 #define MAX310X_MODE2_ECHOSUPR_BIT (1 << 7) /* ECHO suppression enable */ 133 134 /* LCR register bits */ 135 #define MAX310X_LCR_LENGTH0_BIT (1 << 0) /* Word length bit 0 */ 136 #define MAX310X_LCR_LENGTH1_BIT (1 << 1) /* Word length bit 1 137 * 138 * Word length bits table: 139 * 00 -> 5 bit words 140 * 01 -> 6 bit words 141 * 10 -> 7 bit words 142 * 11 -> 8 bit words 143 */ 144 #define MAX310X_LCR_STOPLEN_BIT (1 << 2) /* STOP length bit 145 * 146 * STOP length bit table: 147 * 0 -> 1 stop bit 148 * 1 -> 1-1.5 stop bits if 149 * word length is 5, 150 * 2 stop bits otherwise 151 */ 152 #define MAX310X_LCR_PARITY_BIT (1 << 3) /* Parity bit enable */ 153 #define MAX310X_LCR_EVENPARITY_BIT (1 << 4) /* Even parity bit enable */ 154 #define MAX310X_LCR_FORCEPARITY_BIT (1 << 5) /* 9-bit multidrop parity */ 155 #define MAX310X_LCR_TXBREAK_BIT (1 << 6) /* TX break enable */ 156 #define MAX310X_LCR_RTS_BIT (1 << 7) /* RTS pin control */ 157 158 /* IRDA register bits */ 159 #define MAX310X_IRDA_IRDAEN_BIT (1 << 0) /* IRDA mode enable */ 160 #define MAX310X_IRDA_SIR_BIT (1 << 1) /* SIR mode enable */ 161 162 /* Flow control trigger level register masks */ 163 #define MAX310X_FLOWLVL_HALT_MASK (0x000f) /* Flow control halt level */ 164 #define MAX310X_FLOWLVL_RES_MASK (0x00f0) /* Flow control resume level */ 165 #define MAX310X_FLOWLVL_HALT(words) ((words / 8) & 0x0f) 166 #define MAX310X_FLOWLVL_RES(words) (((words / 8) & 0x0f) << 4) 167 168 /* FIFO interrupt trigger level register masks */ 169 #define MAX310X_FIFOTRIGLVL_TX_MASK (0x0f) /* TX FIFO trigger level */ 170 #define MAX310X_FIFOTRIGLVL_RX_MASK (0xf0) /* RX FIFO trigger level */ 171 #define MAX310X_FIFOTRIGLVL_TX(words) ((words / 8) & 0x0f) 172 #define MAX310X_FIFOTRIGLVL_RX(words) (((words / 8) & 0x0f) << 4) 173 174 /* Flow control register bits */ 175 #define MAX310X_FLOWCTRL_AUTORTS_BIT (1 << 0) /* Auto RTS flow ctrl enable */ 176 #define MAX310X_FLOWCTRL_AUTOCTS_BIT (1 << 1) /* Auto CTS flow ctrl enable */ 177 #define MAX310X_FLOWCTRL_GPIADDR_BIT (1 << 2) /* Enables that GPIO inputs 178 * are used in conjunction with 179 * XOFF2 for definition of 180 * special character */ 181 #define MAX310X_FLOWCTRL_SWFLOWEN_BIT (1 << 3) /* Auto SW flow ctrl enable */ 182 #define MAX310X_FLOWCTRL_SWFLOW0_BIT (1 << 4) /* SWFLOW bit 0 */ 183 #define MAX310X_FLOWCTRL_SWFLOW1_BIT (1 << 5) /* SWFLOW bit 1 184 * 185 * SWFLOW bits 1 & 0 table: 186 * 00 -> no transmitter flow 187 * control 188 * 01 -> receiver compares 189 * XON2 and XOFF2 190 * and controls 191 * transmitter 192 * 10 -> receiver compares 193 * XON1 and XOFF1 194 * and controls 195 * transmitter 196 * 11 -> receiver compares 197 * XON1, XON2, XOFF1 and 198 * XOFF2 and controls 199 * transmitter 200 */ 201 #define MAX310X_FLOWCTRL_SWFLOW2_BIT (1 << 6) /* SWFLOW bit 2 */ 202 #define MAX310X_FLOWCTRL_SWFLOW3_BIT (1 << 7) /* SWFLOW bit 3 203 * 204 * SWFLOW bits 3 & 2 table: 205 * 00 -> no received flow 206 * control 207 * 01 -> transmitter generates 208 * XON2 and XOFF2 209 * 10 -> transmitter generates 210 * XON1 and XOFF1 211 * 11 -> transmitter generates 212 * XON1, XON2, XOFF1 and 213 * XOFF2 214 */ 215 216 /* PLL configuration register masks */ 217 #define MAX310X_PLLCFG_PREDIV_MASK (0x3f) /* PLL predivision value */ 218 #define MAX310X_PLLCFG_PLLFACTOR_MASK (0xc0) /* PLL multiplication factor */ 219 220 /* Baud rate generator configuration register bits */ 221 #define MAX310X_BRGCFG_2XMODE_BIT (1 << 4) /* Double baud rate */ 222 #define MAX310X_BRGCFG_4XMODE_BIT (1 << 5) /* Quadruple baud rate */ 223 224 /* Clock source register bits */ 225 #define MAX310X_CLKSRC_CRYST_BIT (1 << 1) /* Crystal osc enable */ 226 #define MAX310X_CLKSRC_PLL_BIT (1 << 2) /* PLL enable */ 227 #define MAX310X_CLKSRC_PLLBYP_BIT (1 << 3) /* PLL bypass */ 228 #define MAX310X_CLKSRC_EXTCLK_BIT (1 << 4) /* External clock enable */ 229 #define MAX310X_CLKSRC_CLK2RTS_BIT (1 << 7) /* Baud clk to RTS pin */ 230 231 /* Global commands */ 232 #define MAX310X_EXTREG_ENBL (0xce) 233 #define MAX310X_EXTREG_DSBL (0xcd) 234 235 /* Misc definitions */ 236 #define MAX310X_FIFO_SIZE (128) 237 #define MAX310x_REV_MASK (0xf8) 238 #define MAX310X_WRITE_BIT 0x80 239 240 /* MAX3107 specific */ 241 #define MAX3107_REV_ID (0xa0) 242 243 /* MAX3109 specific */ 244 #define MAX3109_REV_ID (0xc0) 245 246 /* MAX14830 specific */ 247 #define MAX14830_BRGCFG_CLKDIS_BIT (1 << 6) /* Clock Disable */ 248 #define MAX14830_REV_ID (0xb0) 249 250 struct max310x_if_cfg { 251 int (*extended_reg_enable)(struct device *dev, bool enable); 252 253 unsigned int rev_id_reg; 254 }; 255 256 struct max310x_devtype { 257 struct { 258 unsigned short min; 259 unsigned short max; 260 } slave_addr; 261 char name[9]; 262 int nr; 263 u8 mode1; 264 int (*detect)(struct device *); 265 void (*power)(struct uart_port *, int); 266 }; 267 268 struct max310x_one { 269 struct uart_port port; 270 struct work_struct tx_work; 271 struct work_struct md_work; 272 struct work_struct rs_work; 273 struct regmap *regmap; 274 275 u8 rx_buf[MAX310X_FIFO_SIZE]; 276 }; 277 #define to_max310x_port(_port) \ 278 container_of(_port, struct max310x_one, port) 279 280 struct max310x_port { 281 const struct max310x_devtype *devtype; 282 const struct max310x_if_cfg *if_cfg; 283 struct regmap *regmap; 284 struct clk *clk; 285 #ifdef CONFIG_GPIOLIB 286 struct gpio_chip gpio; 287 #endif 288 struct max310x_one p[]; 289 }; 290 291 static struct uart_driver max310x_uart = { 292 .owner = THIS_MODULE, 293 .driver_name = MAX310X_NAME, 294 .dev_name = "ttyMAX", 295 .major = MAX310X_MAJOR, 296 .minor = MAX310X_MINOR, 297 .nr = MAX310X_UART_NRMAX, 298 }; 299 300 static DECLARE_BITMAP(max310x_lines, MAX310X_UART_NRMAX); 301 302 static u8 max310x_port_read(struct uart_port *port, u8 reg) 303 { 304 struct max310x_one *one = to_max310x_port(port); 305 unsigned int val = 0; 306 307 regmap_read(one->regmap, reg, &val); 308 309 return val; 310 } 311 312 static void max310x_port_write(struct uart_port *port, u8 reg, u8 val) 313 { 314 struct max310x_one *one = to_max310x_port(port); 315 316 regmap_write(one->regmap, reg, val); 317 } 318 319 static void max310x_port_update(struct uart_port *port, u8 reg, u8 mask, u8 val) 320 { 321 struct max310x_one *one = to_max310x_port(port); 322 323 regmap_update_bits(one->regmap, reg, mask, val); 324 } 325 326 static int max3107_detect(struct device *dev) 327 { 328 struct max310x_port *s = dev_get_drvdata(dev); 329 unsigned int val = 0; 330 int ret; 331 332 ret = regmap_read(s->regmap, MAX310X_REVID_REG, &val); 333 if (ret) 334 return ret; 335 336 if (((val & MAX310x_REV_MASK) != MAX3107_REV_ID)) { 337 dev_err(dev, 338 "%s ID 0x%02x does not match\n", s->devtype->name, val); 339 return -ENODEV; 340 } 341 342 return 0; 343 } 344 345 static int max3108_detect(struct device *dev) 346 { 347 struct max310x_port *s = dev_get_drvdata(dev); 348 unsigned int val = 0; 349 int ret; 350 351 /* MAX3108 have not REV ID register, we just check default value 352 * from clocksource register to make sure everything works. 353 */ 354 ret = regmap_read(s->regmap, MAX310X_CLKSRC_REG, &val); 355 if (ret) 356 return ret; 357 358 if (val != (MAX310X_CLKSRC_EXTCLK_BIT | MAX310X_CLKSRC_PLLBYP_BIT)) { 359 dev_err(dev, "%s not present\n", s->devtype->name); 360 return -ENODEV; 361 } 362 363 return 0; 364 } 365 366 static int max3109_detect(struct device *dev) 367 { 368 struct max310x_port *s = dev_get_drvdata(dev); 369 unsigned int val = 0; 370 int ret; 371 372 ret = s->if_cfg->extended_reg_enable(dev, true); 373 if (ret) 374 return ret; 375 376 regmap_read(s->regmap, s->if_cfg->rev_id_reg, &val); 377 s->if_cfg->extended_reg_enable(dev, false); 378 if (((val & MAX310x_REV_MASK) != MAX3109_REV_ID)) { 379 dev_err(dev, 380 "%s ID 0x%02x does not match\n", s->devtype->name, val); 381 return -ENODEV; 382 } 383 384 return 0; 385 } 386 387 static void max310x_power(struct uart_port *port, int on) 388 { 389 max310x_port_update(port, MAX310X_MODE1_REG, 390 MAX310X_MODE1_FORCESLEEP_BIT, 391 on ? 0 : MAX310X_MODE1_FORCESLEEP_BIT); 392 if (on) 393 msleep(50); 394 } 395 396 static int max14830_detect(struct device *dev) 397 { 398 struct max310x_port *s = dev_get_drvdata(dev); 399 unsigned int val = 0; 400 int ret; 401 402 ret = s->if_cfg->extended_reg_enable(dev, true); 403 if (ret) 404 return ret; 405 406 regmap_read(s->regmap, s->if_cfg->rev_id_reg, &val); 407 s->if_cfg->extended_reg_enable(dev, false); 408 if (((val & MAX310x_REV_MASK) != MAX14830_REV_ID)) { 409 dev_err(dev, 410 "%s ID 0x%02x does not match\n", s->devtype->name, val); 411 return -ENODEV; 412 } 413 414 return 0; 415 } 416 417 static void max14830_power(struct uart_port *port, int on) 418 { 419 max310x_port_update(port, MAX310X_BRGCFG_REG, 420 MAX14830_BRGCFG_CLKDIS_BIT, 421 on ? 0 : MAX14830_BRGCFG_CLKDIS_BIT); 422 if (on) 423 msleep(50); 424 } 425 426 static const struct max310x_devtype max3107_devtype = { 427 .name = "MAX3107", 428 .nr = 1, 429 .mode1 = MAX310X_MODE1_AUTOSLEEP_BIT | MAX310X_MODE1_IRQSEL_BIT, 430 .detect = max3107_detect, 431 .power = max310x_power, 432 .slave_addr = { 433 .min = 0x2c, 434 .max = 0x2f, 435 }, 436 }; 437 438 static const struct max310x_devtype max3108_devtype = { 439 .name = "MAX3108", 440 .nr = 1, 441 .mode1 = MAX310X_MODE1_AUTOSLEEP_BIT, 442 .detect = max3108_detect, 443 .power = max310x_power, 444 .slave_addr = { 445 .min = 0x60, 446 .max = 0x6f, 447 }, 448 }; 449 450 static const struct max310x_devtype max3109_devtype = { 451 .name = "MAX3109", 452 .nr = 2, 453 .mode1 = MAX310X_MODE1_AUTOSLEEP_BIT, 454 .detect = max3109_detect, 455 .power = max310x_power, 456 .slave_addr = { 457 .min = 0x60, 458 .max = 0x6f, 459 }, 460 }; 461 462 static const struct max310x_devtype max14830_devtype = { 463 .name = "MAX14830", 464 .nr = 4, 465 .mode1 = MAX310X_MODE1_IRQSEL_BIT, 466 .detect = max14830_detect, 467 .power = max14830_power, 468 .slave_addr = { 469 .min = 0x60, 470 .max = 0x6f, 471 }, 472 }; 473 474 static bool max310x_reg_writeable(struct device *dev, unsigned int reg) 475 { 476 switch (reg) { 477 case MAX310X_IRQSTS_REG: 478 case MAX310X_LSR_IRQSTS_REG: 479 case MAX310X_SPCHR_IRQSTS_REG: 480 case MAX310X_STS_IRQSTS_REG: 481 case MAX310X_TXFIFOLVL_REG: 482 case MAX310X_RXFIFOLVL_REG: 483 return false; 484 default: 485 break; 486 } 487 488 return true; 489 } 490 491 static bool max310x_reg_volatile(struct device *dev, unsigned int reg) 492 { 493 switch (reg) { 494 case MAX310X_RHR_REG: 495 case MAX310X_IRQSTS_REG: 496 case MAX310X_LSR_IRQSTS_REG: 497 case MAX310X_SPCHR_IRQSTS_REG: 498 case MAX310X_STS_IRQSTS_REG: 499 case MAX310X_TXFIFOLVL_REG: 500 case MAX310X_RXFIFOLVL_REG: 501 case MAX310X_GPIODATA_REG: 502 case MAX310X_BRGDIVLSB_REG: 503 case MAX310X_REG_05: 504 case MAX310X_REG_1F: 505 return true; 506 default: 507 break; 508 } 509 510 return false; 511 } 512 513 static bool max310x_reg_precious(struct device *dev, unsigned int reg) 514 { 515 switch (reg) { 516 case MAX310X_RHR_REG: 517 case MAX310X_IRQSTS_REG: 518 case MAX310X_SPCHR_IRQSTS_REG: 519 case MAX310X_STS_IRQSTS_REG: 520 return true; 521 default: 522 break; 523 } 524 525 return false; 526 } 527 528 static int max310x_set_baud(struct uart_port *port, int baud) 529 { 530 unsigned int mode = 0, div = 0, frac = 0, c = 0, F = 0; 531 532 /* 533 * Calculate the integer divisor first. Select a proper mode 534 * in case if the requested baud is too high for the pre-defined 535 * clocks frequency. 536 */ 537 div = port->uartclk / baud; 538 if (div < 8) { 539 /* Mode x4 */ 540 c = 4; 541 mode = MAX310X_BRGCFG_4XMODE_BIT; 542 } else if (div < 16) { 543 /* Mode x2 */ 544 c = 8; 545 mode = MAX310X_BRGCFG_2XMODE_BIT; 546 } else { 547 c = 16; 548 } 549 550 /* Calculate the divisor in accordance with the fraction coefficient */ 551 div /= c; 552 F = c*baud; 553 554 /* Calculate the baud rate fraction */ 555 if (div > 0) 556 frac = (16*(port->uartclk % F)) / F; 557 else 558 div = 1; 559 560 max310x_port_write(port, MAX310X_BRGDIVMSB_REG, div >> 8); 561 max310x_port_write(port, MAX310X_BRGDIVLSB_REG, div); 562 max310x_port_write(port, MAX310X_BRGCFG_REG, frac | mode); 563 564 /* Return the actual baud rate we just programmed */ 565 return (16*port->uartclk) / (c*(16*div + frac)); 566 } 567 568 static int max310x_update_best_err(unsigned long f, long *besterr) 569 { 570 /* Use baudrate 115200 for calculate error */ 571 long err = f % (460800 * 16); 572 573 if ((*besterr < 0) || (*besterr > err)) { 574 *besterr = err; 575 return 0; 576 } 577 578 return 1; 579 } 580 581 static u32 max310x_set_ref_clk(struct device *dev, struct max310x_port *s, 582 unsigned long freq, bool xtal) 583 { 584 unsigned int div, clksrc, pllcfg = 0; 585 long besterr = -1; 586 unsigned long fdiv, fmul, bestfreq = freq; 587 588 /* First, update error without PLL */ 589 max310x_update_best_err(freq, &besterr); 590 591 /* Try all possible PLL dividers */ 592 for (div = 1; (div <= 63) && besterr; div++) { 593 fdiv = DIV_ROUND_CLOSEST(freq, div); 594 595 /* Try multiplier 6 */ 596 fmul = fdiv * 6; 597 if ((fdiv >= 500000) && (fdiv <= 800000)) 598 if (!max310x_update_best_err(fmul, &besterr)) { 599 pllcfg = (0 << 6) | div; 600 bestfreq = fmul; 601 } 602 /* Try multiplier 48 */ 603 fmul = fdiv * 48; 604 if ((fdiv >= 850000) && (fdiv <= 1200000)) 605 if (!max310x_update_best_err(fmul, &besterr)) { 606 pllcfg = (1 << 6) | div; 607 bestfreq = fmul; 608 } 609 /* Try multiplier 96 */ 610 fmul = fdiv * 96; 611 if ((fdiv >= 425000) && (fdiv <= 1000000)) 612 if (!max310x_update_best_err(fmul, &besterr)) { 613 pllcfg = (2 << 6) | div; 614 bestfreq = fmul; 615 } 616 /* Try multiplier 144 */ 617 fmul = fdiv * 144; 618 if ((fdiv >= 390000) && (fdiv <= 667000)) 619 if (!max310x_update_best_err(fmul, &besterr)) { 620 pllcfg = (3 << 6) | div; 621 bestfreq = fmul; 622 } 623 } 624 625 /* Configure clock source */ 626 clksrc = MAX310X_CLKSRC_EXTCLK_BIT | (xtal ? MAX310X_CLKSRC_CRYST_BIT : 0); 627 628 /* Configure PLL */ 629 if (pllcfg) { 630 clksrc |= MAX310X_CLKSRC_PLL_BIT; 631 regmap_write(s->regmap, MAX310X_PLLCFG_REG, pllcfg); 632 } else 633 clksrc |= MAX310X_CLKSRC_PLLBYP_BIT; 634 635 regmap_write(s->regmap, MAX310X_CLKSRC_REG, clksrc); 636 637 /* Wait for crystal */ 638 if (xtal) { 639 unsigned int val; 640 msleep(10); 641 regmap_read(s->regmap, MAX310X_STS_IRQSTS_REG, &val); 642 if (!(val & MAX310X_STS_CLKREADY_BIT)) { 643 dev_warn(dev, "clock is not stable yet\n"); 644 } 645 } 646 647 return bestfreq; 648 } 649 650 static void max310x_batch_write(struct uart_port *port, u8 *txbuf, unsigned int len) 651 { 652 struct max310x_one *one = to_max310x_port(port); 653 654 regmap_raw_write(one->regmap, MAX310X_THR_REG, txbuf, len); 655 } 656 657 static void max310x_batch_read(struct uart_port *port, u8 *rxbuf, unsigned int len) 658 { 659 struct max310x_one *one = to_max310x_port(port); 660 661 regmap_raw_read(one->regmap, MAX310X_RHR_REG, rxbuf, len); 662 } 663 664 static void max310x_handle_rx(struct uart_port *port, unsigned int rxlen) 665 { 666 struct max310x_one *one = to_max310x_port(port); 667 unsigned int sts, ch, flag, i; 668 669 if (port->read_status_mask == MAX310X_LSR_RXOVR_BIT) { 670 /* We are just reading, happily ignoring any error conditions. 671 * Break condition, parity checking, framing errors -- they 672 * are all ignored. That means that we can do a batch-read. 673 * 674 * There is a small opportunity for race if the RX FIFO 675 * overruns while we're reading the buffer; the datasheets says 676 * that the LSR register applies to the "current" character. 677 * That's also the reason why we cannot do batched reads when 678 * asked to check the individual statuses. 679 * */ 680 681 sts = max310x_port_read(port, MAX310X_LSR_IRQSTS_REG); 682 max310x_batch_read(port, one->rx_buf, rxlen); 683 684 port->icount.rx += rxlen; 685 flag = TTY_NORMAL; 686 sts &= port->read_status_mask; 687 688 if (sts & MAX310X_LSR_RXOVR_BIT) { 689 dev_warn_ratelimited(port->dev, "Hardware RX FIFO overrun\n"); 690 port->icount.overrun++; 691 } 692 693 for (i = 0; i < (rxlen - 1); ++i) 694 uart_insert_char(port, sts, 0, one->rx_buf[i], flag); 695 696 /* 697 * Handle the overrun case for the last character only, since 698 * the RxFIFO overflow happens after it is pushed to the FIFO 699 * tail. 700 */ 701 uart_insert_char(port, sts, MAX310X_LSR_RXOVR_BIT, 702 one->rx_buf[rxlen-1], flag); 703 704 } else { 705 if (unlikely(rxlen >= port->fifosize)) { 706 dev_warn_ratelimited(port->dev, "Possible RX FIFO overrun\n"); 707 port->icount.buf_overrun++; 708 /* Ensure sanity of RX level */ 709 rxlen = port->fifosize; 710 } 711 712 while (rxlen--) { 713 ch = max310x_port_read(port, MAX310X_RHR_REG); 714 sts = max310x_port_read(port, MAX310X_LSR_IRQSTS_REG); 715 716 sts &= MAX310X_LSR_RXPAR_BIT | MAX310X_LSR_FRERR_BIT | 717 MAX310X_LSR_RXOVR_BIT | MAX310X_LSR_RXBRK_BIT; 718 719 port->icount.rx++; 720 flag = TTY_NORMAL; 721 722 if (unlikely(sts)) { 723 if (sts & MAX310X_LSR_RXBRK_BIT) { 724 port->icount.brk++; 725 if (uart_handle_break(port)) 726 continue; 727 } else if (sts & MAX310X_LSR_RXPAR_BIT) 728 port->icount.parity++; 729 else if (sts & MAX310X_LSR_FRERR_BIT) 730 port->icount.frame++; 731 else if (sts & MAX310X_LSR_RXOVR_BIT) 732 port->icount.overrun++; 733 734 sts &= port->read_status_mask; 735 if (sts & MAX310X_LSR_RXBRK_BIT) 736 flag = TTY_BREAK; 737 else if (sts & MAX310X_LSR_RXPAR_BIT) 738 flag = TTY_PARITY; 739 else if (sts & MAX310X_LSR_FRERR_BIT) 740 flag = TTY_FRAME; 741 else if (sts & MAX310X_LSR_RXOVR_BIT) 742 flag = TTY_OVERRUN; 743 } 744 745 if (uart_handle_sysrq_char(port, ch)) 746 continue; 747 748 if (sts & port->ignore_status_mask) 749 continue; 750 751 uart_insert_char(port, sts, MAX310X_LSR_RXOVR_BIT, ch, flag); 752 } 753 } 754 755 tty_flip_buffer_push(&port->state->port); 756 } 757 758 static void max310x_handle_tx(struct uart_port *port) 759 { 760 struct circ_buf *xmit = &port->state->xmit; 761 unsigned int txlen, to_send, until_end; 762 763 if (unlikely(port->x_char)) { 764 max310x_port_write(port, MAX310X_THR_REG, port->x_char); 765 port->icount.tx++; 766 port->x_char = 0; 767 return; 768 } 769 770 if (uart_circ_empty(xmit) || uart_tx_stopped(port)) 771 return; 772 773 /* Get length of data pending in circular buffer */ 774 to_send = uart_circ_chars_pending(xmit); 775 until_end = CIRC_CNT_TO_END(xmit->head, xmit->tail, UART_XMIT_SIZE); 776 if (likely(to_send)) { 777 /* Limit to size of TX FIFO */ 778 txlen = max310x_port_read(port, MAX310X_TXFIFOLVL_REG); 779 txlen = port->fifosize - txlen; 780 to_send = (to_send > txlen) ? txlen : to_send; 781 782 if (until_end < to_send) { 783 /* It's a circ buffer -- wrap around. 784 * We could do that in one SPI transaction, but meh. */ 785 max310x_batch_write(port, xmit->buf + xmit->tail, until_end); 786 max310x_batch_write(port, xmit->buf, to_send - until_end); 787 } else { 788 max310x_batch_write(port, xmit->buf + xmit->tail, to_send); 789 } 790 791 /* Add data to send */ 792 port->icount.tx += to_send; 793 xmit->tail = (xmit->tail + to_send) & (UART_XMIT_SIZE - 1); 794 } 795 796 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) 797 uart_write_wakeup(port); 798 } 799 800 static void max310x_start_tx(struct uart_port *port) 801 { 802 struct max310x_one *one = to_max310x_port(port); 803 804 schedule_work(&one->tx_work); 805 } 806 807 static irqreturn_t max310x_port_irq(struct max310x_port *s, int portno) 808 { 809 struct uart_port *port = &s->p[portno].port; 810 irqreturn_t res = IRQ_NONE; 811 812 do { 813 unsigned int ists, lsr, rxlen; 814 815 /* Read IRQ status & RX FIFO level */ 816 ists = max310x_port_read(port, MAX310X_IRQSTS_REG); 817 rxlen = max310x_port_read(port, MAX310X_RXFIFOLVL_REG); 818 if (!ists && !rxlen) 819 break; 820 821 res = IRQ_HANDLED; 822 823 if (ists & MAX310X_IRQ_CTS_BIT) { 824 lsr = max310x_port_read(port, MAX310X_LSR_IRQSTS_REG); 825 uart_handle_cts_change(port, 826 !!(lsr & MAX310X_LSR_CTS_BIT)); 827 } 828 if (rxlen) 829 max310x_handle_rx(port, rxlen); 830 if (ists & MAX310X_IRQ_TXEMPTY_BIT) 831 max310x_start_tx(port); 832 } while (1); 833 return res; 834 } 835 836 static irqreturn_t max310x_ist(int irq, void *dev_id) 837 { 838 struct max310x_port *s = (struct max310x_port *)dev_id; 839 bool handled = false; 840 841 if (s->devtype->nr > 1) { 842 do { 843 unsigned int val = ~0; 844 845 WARN_ON_ONCE(regmap_read(s->regmap, 846 MAX310X_GLOBALIRQ_REG, &val)); 847 val = ((1 << s->devtype->nr) - 1) & ~val; 848 if (!val) 849 break; 850 if (max310x_port_irq(s, fls(val) - 1) == IRQ_HANDLED) 851 handled = true; 852 } while (1); 853 } else { 854 if (max310x_port_irq(s, 0) == IRQ_HANDLED) 855 handled = true; 856 } 857 858 return IRQ_RETVAL(handled); 859 } 860 861 static void max310x_tx_proc(struct work_struct *ws) 862 { 863 struct max310x_one *one = container_of(ws, struct max310x_one, tx_work); 864 865 max310x_handle_tx(&one->port); 866 } 867 868 static unsigned int max310x_tx_empty(struct uart_port *port) 869 { 870 u8 lvl = max310x_port_read(port, MAX310X_TXFIFOLVL_REG); 871 872 return lvl ? 0 : TIOCSER_TEMT; 873 } 874 875 static unsigned int max310x_get_mctrl(struct uart_port *port) 876 { 877 /* DCD and DSR are not wired and CTS/RTS is handled automatically 878 * so just indicate DSR and CAR asserted 879 */ 880 return TIOCM_DSR | TIOCM_CAR; 881 } 882 883 static void max310x_md_proc(struct work_struct *ws) 884 { 885 struct max310x_one *one = container_of(ws, struct max310x_one, md_work); 886 887 max310x_port_update(&one->port, MAX310X_MODE2_REG, 888 MAX310X_MODE2_LOOPBACK_BIT, 889 (one->port.mctrl & TIOCM_LOOP) ? 890 MAX310X_MODE2_LOOPBACK_BIT : 0); 891 } 892 893 static void max310x_set_mctrl(struct uart_port *port, unsigned int mctrl) 894 { 895 struct max310x_one *one = to_max310x_port(port); 896 897 schedule_work(&one->md_work); 898 } 899 900 static void max310x_break_ctl(struct uart_port *port, int break_state) 901 { 902 max310x_port_update(port, MAX310X_LCR_REG, 903 MAX310X_LCR_TXBREAK_BIT, 904 break_state ? MAX310X_LCR_TXBREAK_BIT : 0); 905 } 906 907 static void max310x_set_termios(struct uart_port *port, 908 struct ktermios *termios, 909 const struct ktermios *old) 910 { 911 unsigned int lcr = 0, flow = 0; 912 int baud; 913 914 /* Mask termios capabilities we don't support */ 915 termios->c_cflag &= ~CMSPAR; 916 917 /* Word size */ 918 switch (termios->c_cflag & CSIZE) { 919 case CS5: 920 break; 921 case CS6: 922 lcr = MAX310X_LCR_LENGTH0_BIT; 923 break; 924 case CS7: 925 lcr = MAX310X_LCR_LENGTH1_BIT; 926 break; 927 case CS8: 928 default: 929 lcr = MAX310X_LCR_LENGTH1_BIT | MAX310X_LCR_LENGTH0_BIT; 930 break; 931 } 932 933 /* Parity */ 934 if (termios->c_cflag & PARENB) { 935 lcr |= MAX310X_LCR_PARITY_BIT; 936 if (!(termios->c_cflag & PARODD)) 937 lcr |= MAX310X_LCR_EVENPARITY_BIT; 938 } 939 940 /* Stop bits */ 941 if (termios->c_cflag & CSTOPB) 942 lcr |= MAX310X_LCR_STOPLEN_BIT; /* 2 stops */ 943 944 /* Update LCR register */ 945 max310x_port_write(port, MAX310X_LCR_REG, lcr); 946 947 /* Set read status mask */ 948 port->read_status_mask = MAX310X_LSR_RXOVR_BIT; 949 if (termios->c_iflag & INPCK) 950 port->read_status_mask |= MAX310X_LSR_RXPAR_BIT | 951 MAX310X_LSR_FRERR_BIT; 952 if (termios->c_iflag & (IGNBRK | BRKINT | PARMRK)) 953 port->read_status_mask |= MAX310X_LSR_RXBRK_BIT; 954 955 /* Set status ignore mask */ 956 port->ignore_status_mask = 0; 957 if (termios->c_iflag & IGNBRK) 958 port->ignore_status_mask |= MAX310X_LSR_RXBRK_BIT; 959 if (!(termios->c_cflag & CREAD)) 960 port->ignore_status_mask |= MAX310X_LSR_RXPAR_BIT | 961 MAX310X_LSR_RXOVR_BIT | 962 MAX310X_LSR_FRERR_BIT | 963 MAX310X_LSR_RXBRK_BIT; 964 965 /* Configure flow control */ 966 max310x_port_write(port, MAX310X_XON1_REG, termios->c_cc[VSTART]); 967 max310x_port_write(port, MAX310X_XOFF1_REG, termios->c_cc[VSTOP]); 968 969 /* Disable transmitter before enabling AutoCTS or auto transmitter 970 * flow control 971 */ 972 if (termios->c_cflag & CRTSCTS || termios->c_iflag & IXOFF) { 973 max310x_port_update(port, MAX310X_MODE1_REG, 974 MAX310X_MODE1_TXDIS_BIT, 975 MAX310X_MODE1_TXDIS_BIT); 976 } 977 978 port->status &= ~(UPSTAT_AUTOCTS | UPSTAT_AUTORTS | UPSTAT_AUTOXOFF); 979 980 if (termios->c_cflag & CRTSCTS) { 981 /* Enable AUTORTS and AUTOCTS */ 982 port->status |= UPSTAT_AUTOCTS | UPSTAT_AUTORTS; 983 flow |= MAX310X_FLOWCTRL_AUTOCTS_BIT | 984 MAX310X_FLOWCTRL_AUTORTS_BIT; 985 } 986 if (termios->c_iflag & IXON) 987 flow |= MAX310X_FLOWCTRL_SWFLOW3_BIT | 988 MAX310X_FLOWCTRL_SWFLOWEN_BIT; 989 if (termios->c_iflag & IXOFF) { 990 port->status |= UPSTAT_AUTOXOFF; 991 flow |= MAX310X_FLOWCTRL_SWFLOW1_BIT | 992 MAX310X_FLOWCTRL_SWFLOWEN_BIT; 993 } 994 max310x_port_write(port, MAX310X_FLOWCTRL_REG, flow); 995 996 /* Enable transmitter after disabling AutoCTS and auto transmitter 997 * flow control 998 */ 999 if (!(termios->c_cflag & CRTSCTS) && !(termios->c_iflag & IXOFF)) { 1000 max310x_port_update(port, MAX310X_MODE1_REG, 1001 MAX310X_MODE1_TXDIS_BIT, 1002 0); 1003 } 1004 1005 /* Get baud rate generator configuration */ 1006 baud = uart_get_baud_rate(port, termios, old, 1007 port->uartclk / 16 / 0xffff, 1008 port->uartclk / 4); 1009 1010 /* Setup baudrate generator */ 1011 baud = max310x_set_baud(port, baud); 1012 1013 /* Update timeout according to new baud rate */ 1014 uart_update_timeout(port, termios->c_cflag, baud); 1015 } 1016 1017 static void max310x_rs_proc(struct work_struct *ws) 1018 { 1019 struct max310x_one *one = container_of(ws, struct max310x_one, rs_work); 1020 unsigned int delay, mode1 = 0, mode2 = 0; 1021 1022 delay = (one->port.rs485.delay_rts_before_send << 4) | 1023 one->port.rs485.delay_rts_after_send; 1024 max310x_port_write(&one->port, MAX310X_HDPIXDELAY_REG, delay); 1025 1026 if (one->port.rs485.flags & SER_RS485_ENABLED) { 1027 mode1 = MAX310X_MODE1_TRNSCVCTRL_BIT; 1028 1029 if (!(one->port.rs485.flags & SER_RS485_RX_DURING_TX)) 1030 mode2 = MAX310X_MODE2_ECHOSUPR_BIT; 1031 } 1032 1033 max310x_port_update(&one->port, MAX310X_MODE1_REG, 1034 MAX310X_MODE1_TRNSCVCTRL_BIT, mode1); 1035 max310x_port_update(&one->port, MAX310X_MODE2_REG, 1036 MAX310X_MODE2_ECHOSUPR_BIT, mode2); 1037 } 1038 1039 static int max310x_rs485_config(struct uart_port *port, struct ktermios *termios, 1040 struct serial_rs485 *rs485) 1041 { 1042 struct max310x_one *one = to_max310x_port(port); 1043 1044 if ((rs485->delay_rts_before_send > 0x0f) || 1045 (rs485->delay_rts_after_send > 0x0f)) 1046 return -ERANGE; 1047 1048 port->rs485 = *rs485; 1049 1050 schedule_work(&one->rs_work); 1051 1052 return 0; 1053 } 1054 1055 static int max310x_startup(struct uart_port *port) 1056 { 1057 struct max310x_port *s = dev_get_drvdata(port->dev); 1058 unsigned int val; 1059 1060 s->devtype->power(port, 1); 1061 1062 /* Configure MODE1 register */ 1063 max310x_port_update(port, MAX310X_MODE1_REG, 1064 MAX310X_MODE1_TRNSCVCTRL_BIT, 0); 1065 1066 /* Configure MODE2 register & Reset FIFOs*/ 1067 val = MAX310X_MODE2_RXEMPTINV_BIT | MAX310X_MODE2_FIFORST_BIT; 1068 max310x_port_write(port, MAX310X_MODE2_REG, val); 1069 max310x_port_update(port, MAX310X_MODE2_REG, 1070 MAX310X_MODE2_FIFORST_BIT, 0); 1071 1072 /* Configure mode1/mode2 to have rs485/rs232 enabled at startup */ 1073 val = (clamp(port->rs485.delay_rts_before_send, 0U, 15U) << 4) | 1074 clamp(port->rs485.delay_rts_after_send, 0U, 15U); 1075 max310x_port_write(port, MAX310X_HDPIXDELAY_REG, val); 1076 1077 if (port->rs485.flags & SER_RS485_ENABLED) { 1078 max310x_port_update(port, MAX310X_MODE1_REG, 1079 MAX310X_MODE1_TRNSCVCTRL_BIT, 1080 MAX310X_MODE1_TRNSCVCTRL_BIT); 1081 1082 if (!(port->rs485.flags & SER_RS485_RX_DURING_TX)) 1083 max310x_port_update(port, MAX310X_MODE2_REG, 1084 MAX310X_MODE2_ECHOSUPR_BIT, 1085 MAX310X_MODE2_ECHOSUPR_BIT); 1086 } 1087 1088 /* Configure flow control levels */ 1089 /* Flow control halt level 96, resume level 48 */ 1090 max310x_port_write(port, MAX310X_FLOWLVL_REG, 1091 MAX310X_FLOWLVL_RES(48) | MAX310X_FLOWLVL_HALT(96)); 1092 1093 /* Clear IRQ status register */ 1094 max310x_port_read(port, MAX310X_IRQSTS_REG); 1095 1096 /* Enable RX, TX, CTS change interrupts */ 1097 val = MAX310X_IRQ_RXEMPTY_BIT | MAX310X_IRQ_TXEMPTY_BIT; 1098 max310x_port_write(port, MAX310X_IRQEN_REG, val | MAX310X_IRQ_CTS_BIT); 1099 1100 return 0; 1101 } 1102 1103 static void max310x_shutdown(struct uart_port *port) 1104 { 1105 struct max310x_port *s = dev_get_drvdata(port->dev); 1106 1107 /* Disable all interrupts */ 1108 max310x_port_write(port, MAX310X_IRQEN_REG, 0); 1109 1110 s->devtype->power(port, 0); 1111 } 1112 1113 static const char *max310x_type(struct uart_port *port) 1114 { 1115 struct max310x_port *s = dev_get_drvdata(port->dev); 1116 1117 return (port->type == PORT_MAX310X) ? s->devtype->name : NULL; 1118 } 1119 1120 static int max310x_request_port(struct uart_port *port) 1121 { 1122 /* Do nothing */ 1123 return 0; 1124 } 1125 1126 static void max310x_config_port(struct uart_port *port, int flags) 1127 { 1128 if (flags & UART_CONFIG_TYPE) 1129 port->type = PORT_MAX310X; 1130 } 1131 1132 static int max310x_verify_port(struct uart_port *port, struct serial_struct *s) 1133 { 1134 if ((s->type != PORT_UNKNOWN) && (s->type != PORT_MAX310X)) 1135 return -EINVAL; 1136 if (s->irq != port->irq) 1137 return -EINVAL; 1138 1139 return 0; 1140 } 1141 1142 static void max310x_null_void(struct uart_port *port) 1143 { 1144 /* Do nothing */ 1145 } 1146 1147 static const struct uart_ops max310x_ops = { 1148 .tx_empty = max310x_tx_empty, 1149 .set_mctrl = max310x_set_mctrl, 1150 .get_mctrl = max310x_get_mctrl, 1151 .stop_tx = max310x_null_void, 1152 .start_tx = max310x_start_tx, 1153 .stop_rx = max310x_null_void, 1154 .break_ctl = max310x_break_ctl, 1155 .startup = max310x_startup, 1156 .shutdown = max310x_shutdown, 1157 .set_termios = max310x_set_termios, 1158 .type = max310x_type, 1159 .request_port = max310x_request_port, 1160 .release_port = max310x_null_void, 1161 .config_port = max310x_config_port, 1162 .verify_port = max310x_verify_port, 1163 }; 1164 1165 static int __maybe_unused max310x_suspend(struct device *dev) 1166 { 1167 struct max310x_port *s = dev_get_drvdata(dev); 1168 int i; 1169 1170 for (i = 0; i < s->devtype->nr; i++) { 1171 uart_suspend_port(&max310x_uart, &s->p[i].port); 1172 s->devtype->power(&s->p[i].port, 0); 1173 } 1174 1175 return 0; 1176 } 1177 1178 static int __maybe_unused max310x_resume(struct device *dev) 1179 { 1180 struct max310x_port *s = dev_get_drvdata(dev); 1181 int i; 1182 1183 for (i = 0; i < s->devtype->nr; i++) { 1184 s->devtype->power(&s->p[i].port, 1); 1185 uart_resume_port(&max310x_uart, &s->p[i].port); 1186 } 1187 1188 return 0; 1189 } 1190 1191 static SIMPLE_DEV_PM_OPS(max310x_pm_ops, max310x_suspend, max310x_resume); 1192 1193 #ifdef CONFIG_GPIOLIB 1194 static int max310x_gpio_get(struct gpio_chip *chip, unsigned offset) 1195 { 1196 unsigned int val; 1197 struct max310x_port *s = gpiochip_get_data(chip); 1198 struct uart_port *port = &s->p[offset / 4].port; 1199 1200 val = max310x_port_read(port, MAX310X_GPIODATA_REG); 1201 1202 return !!((val >> 4) & (1 << (offset % 4))); 1203 } 1204 1205 static void max310x_gpio_set(struct gpio_chip *chip, unsigned offset, int value) 1206 { 1207 struct max310x_port *s = gpiochip_get_data(chip); 1208 struct uart_port *port = &s->p[offset / 4].port; 1209 1210 max310x_port_update(port, MAX310X_GPIODATA_REG, 1 << (offset % 4), 1211 value ? 1 << (offset % 4) : 0); 1212 } 1213 1214 static int max310x_gpio_direction_input(struct gpio_chip *chip, unsigned offset) 1215 { 1216 struct max310x_port *s = gpiochip_get_data(chip); 1217 struct uart_port *port = &s->p[offset / 4].port; 1218 1219 max310x_port_update(port, MAX310X_GPIOCFG_REG, 1 << (offset % 4), 0); 1220 1221 return 0; 1222 } 1223 1224 static int max310x_gpio_direction_output(struct gpio_chip *chip, 1225 unsigned offset, int value) 1226 { 1227 struct max310x_port *s = gpiochip_get_data(chip); 1228 struct uart_port *port = &s->p[offset / 4].port; 1229 1230 max310x_port_update(port, MAX310X_GPIODATA_REG, 1 << (offset % 4), 1231 value ? 1 << (offset % 4) : 0); 1232 max310x_port_update(port, MAX310X_GPIOCFG_REG, 1 << (offset % 4), 1233 1 << (offset % 4)); 1234 1235 return 0; 1236 } 1237 1238 static int max310x_gpio_set_config(struct gpio_chip *chip, unsigned int offset, 1239 unsigned long config) 1240 { 1241 struct max310x_port *s = gpiochip_get_data(chip); 1242 struct uart_port *port = &s->p[offset / 4].port; 1243 1244 switch (pinconf_to_config_param(config)) { 1245 case PIN_CONFIG_DRIVE_OPEN_DRAIN: 1246 max310x_port_update(port, MAX310X_GPIOCFG_REG, 1247 1 << ((offset % 4) + 4), 1248 1 << ((offset % 4) + 4)); 1249 return 0; 1250 case PIN_CONFIG_DRIVE_PUSH_PULL: 1251 max310x_port_update(port, MAX310X_GPIOCFG_REG, 1252 1 << ((offset % 4) + 4), 0); 1253 return 0; 1254 default: 1255 return -ENOTSUPP; 1256 } 1257 } 1258 #endif 1259 1260 static const struct serial_rs485 max310x_rs485_supported = { 1261 .flags = SER_RS485_ENABLED | SER_RS485_RTS_ON_SEND | SER_RS485_RX_DURING_TX, 1262 .delay_rts_before_send = 1, 1263 .delay_rts_after_send = 1, 1264 }; 1265 1266 static int max310x_probe(struct device *dev, const struct max310x_devtype *devtype, 1267 const struct max310x_if_cfg *if_cfg, 1268 struct regmap *regmaps[], int irq) 1269 { 1270 int i, ret, fmin, fmax, freq; 1271 struct max310x_port *s; 1272 u32 uartclk = 0; 1273 bool xtal; 1274 1275 for (i = 0; i < devtype->nr; i++) 1276 if (IS_ERR(regmaps[i])) 1277 return PTR_ERR(regmaps[i]); 1278 1279 /* Alloc port structure */ 1280 s = devm_kzalloc(dev, struct_size(s, p, devtype->nr), GFP_KERNEL); 1281 if (!s) { 1282 dev_err(dev, "Error allocating port structure\n"); 1283 return -ENOMEM; 1284 } 1285 1286 /* Always ask for fixed clock rate from a property. */ 1287 device_property_read_u32(dev, "clock-frequency", &uartclk); 1288 1289 xtal = device_property_match_string(dev, "clock-names", "osc") < 0; 1290 if (xtal) 1291 s->clk = devm_clk_get_optional(dev, "xtal"); 1292 else 1293 s->clk = devm_clk_get_optional(dev, "osc"); 1294 if (IS_ERR(s->clk)) 1295 return PTR_ERR(s->clk); 1296 1297 ret = clk_prepare_enable(s->clk); 1298 if (ret) 1299 return ret; 1300 1301 freq = clk_get_rate(s->clk); 1302 if (freq == 0) 1303 freq = uartclk; 1304 if (freq == 0) { 1305 dev_err(dev, "Cannot get clock rate\n"); 1306 ret = -EINVAL; 1307 goto out_clk; 1308 } 1309 1310 if (xtal) { 1311 fmin = 1000000; 1312 fmax = 4000000; 1313 } else { 1314 fmin = 500000; 1315 fmax = 35000000; 1316 } 1317 1318 /* Check frequency limits */ 1319 if (freq < fmin || freq > fmax) { 1320 ret = -ERANGE; 1321 goto out_clk; 1322 } 1323 1324 s->regmap = regmaps[0]; 1325 s->devtype = devtype; 1326 s->if_cfg = if_cfg; 1327 dev_set_drvdata(dev, s); 1328 1329 /* Check device to ensure we are talking to what we expect */ 1330 ret = devtype->detect(dev); 1331 if (ret) 1332 goto out_clk; 1333 1334 for (i = 0; i < devtype->nr; i++) { 1335 /* Reset port */ 1336 regmap_write(regmaps[i], MAX310X_MODE2_REG, 1337 MAX310X_MODE2_RST_BIT); 1338 /* Clear port reset */ 1339 regmap_write(regmaps[i], MAX310X_MODE2_REG, 0); 1340 1341 /* Wait for port startup */ 1342 do { 1343 regmap_read(regmaps[i], MAX310X_BRGDIVLSB_REG, &ret); 1344 } while (ret != 0x01); 1345 1346 regmap_write(regmaps[i], MAX310X_MODE1_REG, devtype->mode1); 1347 } 1348 1349 uartclk = max310x_set_ref_clk(dev, s, freq, xtal); 1350 dev_dbg(dev, "Reference clock set to %i Hz\n", uartclk); 1351 1352 for (i = 0; i < devtype->nr; i++) { 1353 unsigned int line; 1354 1355 line = find_first_zero_bit(max310x_lines, MAX310X_UART_NRMAX); 1356 if (line == MAX310X_UART_NRMAX) { 1357 ret = -ERANGE; 1358 goto out_uart; 1359 } 1360 1361 /* Initialize port data */ 1362 s->p[i].port.line = line; 1363 s->p[i].port.dev = dev; 1364 s->p[i].port.irq = irq; 1365 s->p[i].port.type = PORT_MAX310X; 1366 s->p[i].port.fifosize = MAX310X_FIFO_SIZE; 1367 s->p[i].port.flags = UPF_FIXED_TYPE | UPF_LOW_LATENCY; 1368 s->p[i].port.iotype = UPIO_PORT; 1369 s->p[i].port.iobase = i; 1370 s->p[i].port.membase = (void __iomem *)~0; 1371 s->p[i].port.uartclk = uartclk; 1372 s->p[i].port.rs485_config = max310x_rs485_config; 1373 s->p[i].port.rs485_supported = max310x_rs485_supported; 1374 s->p[i].port.ops = &max310x_ops; 1375 s->p[i].regmap = regmaps[i]; 1376 1377 /* Disable all interrupts */ 1378 max310x_port_write(&s->p[i].port, MAX310X_IRQEN_REG, 0); 1379 /* Clear IRQ status register */ 1380 max310x_port_read(&s->p[i].port, MAX310X_IRQSTS_REG); 1381 /* Initialize queue for start TX */ 1382 INIT_WORK(&s->p[i].tx_work, max310x_tx_proc); 1383 /* Initialize queue for changing LOOPBACK mode */ 1384 INIT_WORK(&s->p[i].md_work, max310x_md_proc); 1385 /* Initialize queue for changing RS485 mode */ 1386 INIT_WORK(&s->p[i].rs_work, max310x_rs_proc); 1387 1388 /* Register port */ 1389 ret = uart_add_one_port(&max310x_uart, &s->p[i].port); 1390 if (ret) { 1391 s->p[i].port.dev = NULL; 1392 goto out_uart; 1393 } 1394 set_bit(line, max310x_lines); 1395 1396 /* Go to suspend mode */ 1397 devtype->power(&s->p[i].port, 0); 1398 } 1399 1400 #ifdef CONFIG_GPIOLIB 1401 /* Setup GPIO cotroller */ 1402 s->gpio.owner = THIS_MODULE; 1403 s->gpio.parent = dev; 1404 s->gpio.label = devtype->name; 1405 s->gpio.direction_input = max310x_gpio_direction_input; 1406 s->gpio.get = max310x_gpio_get; 1407 s->gpio.direction_output= max310x_gpio_direction_output; 1408 s->gpio.set = max310x_gpio_set; 1409 s->gpio.set_config = max310x_gpio_set_config; 1410 s->gpio.base = -1; 1411 s->gpio.ngpio = devtype->nr * 4; 1412 s->gpio.can_sleep = 1; 1413 ret = devm_gpiochip_add_data(dev, &s->gpio, s); 1414 if (ret) 1415 goto out_uart; 1416 #endif 1417 1418 /* Setup interrupt */ 1419 ret = devm_request_threaded_irq(dev, irq, NULL, max310x_ist, 1420 IRQF_ONESHOT | IRQF_SHARED, dev_name(dev), s); 1421 if (!ret) 1422 return 0; 1423 1424 dev_err(dev, "Unable to reguest IRQ %i\n", irq); 1425 1426 out_uart: 1427 for (i = 0; i < devtype->nr; i++) { 1428 if (s->p[i].port.dev) { 1429 uart_remove_one_port(&max310x_uart, &s->p[i].port); 1430 clear_bit(s->p[i].port.line, max310x_lines); 1431 } 1432 } 1433 1434 out_clk: 1435 clk_disable_unprepare(s->clk); 1436 1437 return ret; 1438 } 1439 1440 static void max310x_remove(struct device *dev) 1441 { 1442 struct max310x_port *s = dev_get_drvdata(dev); 1443 int i; 1444 1445 for (i = 0; i < s->devtype->nr; i++) { 1446 cancel_work_sync(&s->p[i].tx_work); 1447 cancel_work_sync(&s->p[i].md_work); 1448 cancel_work_sync(&s->p[i].rs_work); 1449 uart_remove_one_port(&max310x_uart, &s->p[i].port); 1450 clear_bit(s->p[i].port.line, max310x_lines); 1451 s->devtype->power(&s->p[i].port, 0); 1452 } 1453 1454 clk_disable_unprepare(s->clk); 1455 } 1456 1457 static const struct of_device_id __maybe_unused max310x_dt_ids[] = { 1458 { .compatible = "maxim,max3107", .data = &max3107_devtype, }, 1459 { .compatible = "maxim,max3108", .data = &max3108_devtype, }, 1460 { .compatible = "maxim,max3109", .data = &max3109_devtype, }, 1461 { .compatible = "maxim,max14830", .data = &max14830_devtype }, 1462 { } 1463 }; 1464 MODULE_DEVICE_TABLE(of, max310x_dt_ids); 1465 1466 static struct regmap_config regcfg = { 1467 .reg_bits = 8, 1468 .val_bits = 8, 1469 .write_flag_mask = MAX310X_WRITE_BIT, 1470 .cache_type = REGCACHE_RBTREE, 1471 .max_register = MAX310X_REG_1F, 1472 .writeable_reg = max310x_reg_writeable, 1473 .volatile_reg = max310x_reg_volatile, 1474 .precious_reg = max310x_reg_precious, 1475 }; 1476 1477 #ifdef CONFIG_SPI_MASTER 1478 static int max310x_spi_extended_reg_enable(struct device *dev, bool enable) 1479 { 1480 struct max310x_port *s = dev_get_drvdata(dev); 1481 1482 return regmap_write(s->regmap, MAX310X_GLOBALCMD_REG, 1483 enable ? MAX310X_EXTREG_ENBL : MAX310X_EXTREG_DSBL); 1484 } 1485 1486 static const struct max310x_if_cfg __maybe_unused max310x_spi_if_cfg = { 1487 .extended_reg_enable = max310x_spi_extended_reg_enable, 1488 .rev_id_reg = MAX310X_SPI_REVID_EXTREG, 1489 }; 1490 1491 static int max310x_spi_probe(struct spi_device *spi) 1492 { 1493 const struct max310x_devtype *devtype; 1494 struct regmap *regmaps[4]; 1495 unsigned int i; 1496 int ret; 1497 1498 /* Setup SPI bus */ 1499 spi->bits_per_word = 8; 1500 spi->mode = spi->mode ? : SPI_MODE_0; 1501 spi->max_speed_hz = spi->max_speed_hz ? : 26000000; 1502 ret = spi_setup(spi); 1503 if (ret) 1504 return ret; 1505 1506 devtype = device_get_match_data(&spi->dev); 1507 if (!devtype) 1508 devtype = (struct max310x_devtype *)spi_get_device_id(spi)->driver_data; 1509 1510 for (i = 0; i < devtype->nr; i++) { 1511 u8 port_mask = i * 0x20; 1512 regcfg.read_flag_mask = port_mask; 1513 regcfg.write_flag_mask = port_mask | MAX310X_WRITE_BIT; 1514 regmaps[i] = devm_regmap_init_spi(spi, ®cfg); 1515 } 1516 1517 return max310x_probe(&spi->dev, devtype, &max310x_spi_if_cfg, regmaps, spi->irq); 1518 } 1519 1520 static void max310x_spi_remove(struct spi_device *spi) 1521 { 1522 max310x_remove(&spi->dev); 1523 } 1524 1525 static const struct spi_device_id max310x_id_table[] = { 1526 { "max3107", (kernel_ulong_t)&max3107_devtype, }, 1527 { "max3108", (kernel_ulong_t)&max3108_devtype, }, 1528 { "max3109", (kernel_ulong_t)&max3109_devtype, }, 1529 { "max14830", (kernel_ulong_t)&max14830_devtype, }, 1530 { } 1531 }; 1532 MODULE_DEVICE_TABLE(spi, max310x_id_table); 1533 1534 static struct spi_driver max310x_spi_driver = { 1535 .driver = { 1536 .name = MAX310X_NAME, 1537 .of_match_table = max310x_dt_ids, 1538 .pm = &max310x_pm_ops, 1539 }, 1540 .probe = max310x_spi_probe, 1541 .remove = max310x_spi_remove, 1542 .id_table = max310x_id_table, 1543 }; 1544 #endif 1545 1546 #ifdef CONFIG_I2C 1547 static int max310x_i2c_extended_reg_enable(struct device *dev, bool enable) 1548 { 1549 return 0; 1550 } 1551 1552 static struct regmap_config regcfg_i2c = { 1553 .reg_bits = 8, 1554 .val_bits = 8, 1555 .cache_type = REGCACHE_RBTREE, 1556 .writeable_reg = max310x_reg_writeable, 1557 .volatile_reg = max310x_reg_volatile, 1558 .precious_reg = max310x_reg_precious, 1559 .max_register = MAX310X_I2C_REVID_EXTREG, 1560 }; 1561 1562 static const struct max310x_if_cfg max310x_i2c_if_cfg = { 1563 .extended_reg_enable = max310x_i2c_extended_reg_enable, 1564 .rev_id_reg = MAX310X_I2C_REVID_EXTREG, 1565 }; 1566 1567 static unsigned short max310x_i2c_slave_addr(unsigned short addr, 1568 unsigned int nr) 1569 { 1570 /* 1571 * For MAX14830 and MAX3109, the slave address depends on what the 1572 * A0 and A1 pins are tied to. 1573 * See Table I2C Address Map of the datasheet. 1574 * Based on that table, the following formulas were determined. 1575 * UART1 - UART0 = 0x10 1576 * UART2 - UART1 = 0x20 + 0x10 1577 * UART3 - UART2 = 0x10 1578 */ 1579 1580 addr -= nr * 0x10; 1581 1582 if (nr >= 2) 1583 addr -= 0x20; 1584 1585 return addr; 1586 } 1587 1588 static int max310x_i2c_probe(struct i2c_client *client) 1589 { 1590 const struct max310x_devtype *devtype = 1591 device_get_match_data(&client->dev); 1592 struct i2c_client *port_client; 1593 struct regmap *regmaps[4]; 1594 unsigned int i; 1595 u8 port_addr; 1596 1597 if (client->addr < devtype->slave_addr.min || 1598 client->addr > devtype->slave_addr.max) 1599 return dev_err_probe(&client->dev, -EINVAL, 1600 "Slave addr 0x%x outside of range [0x%x, 0x%x]\n", 1601 client->addr, devtype->slave_addr.min, 1602 devtype->slave_addr.max); 1603 1604 regmaps[0] = devm_regmap_init_i2c(client, ®cfg_i2c); 1605 1606 for (i = 1; i < devtype->nr; i++) { 1607 port_addr = max310x_i2c_slave_addr(client->addr, i); 1608 port_client = devm_i2c_new_dummy_device(&client->dev, 1609 client->adapter, 1610 port_addr); 1611 1612 regmaps[i] = devm_regmap_init_i2c(port_client, ®cfg_i2c); 1613 } 1614 1615 return max310x_probe(&client->dev, devtype, &max310x_i2c_if_cfg, 1616 regmaps, client->irq); 1617 } 1618 1619 static void max310x_i2c_remove(struct i2c_client *client) 1620 { 1621 max310x_remove(&client->dev); 1622 } 1623 1624 static struct i2c_driver max310x_i2c_driver = { 1625 .driver = { 1626 .name = MAX310X_NAME, 1627 .of_match_table = max310x_dt_ids, 1628 .pm = &max310x_pm_ops, 1629 }, 1630 .probe_new = max310x_i2c_probe, 1631 .remove = max310x_i2c_remove, 1632 }; 1633 #endif 1634 1635 static int __init max310x_uart_init(void) 1636 { 1637 int ret; 1638 1639 bitmap_zero(max310x_lines, MAX310X_UART_NRMAX); 1640 1641 ret = uart_register_driver(&max310x_uart); 1642 if (ret) 1643 return ret; 1644 1645 #ifdef CONFIG_SPI_MASTER 1646 ret = spi_register_driver(&max310x_spi_driver); 1647 if (ret) 1648 goto err_spi_register; 1649 #endif 1650 1651 #ifdef CONFIG_I2C 1652 ret = i2c_add_driver(&max310x_i2c_driver); 1653 if (ret) 1654 goto err_i2c_register; 1655 #endif 1656 1657 return 0; 1658 1659 #ifdef CONFIG_I2C 1660 err_i2c_register: 1661 spi_unregister_driver(&max310x_spi_driver); 1662 #endif 1663 1664 err_spi_register: 1665 uart_unregister_driver(&max310x_uart); 1666 1667 return ret; 1668 } 1669 module_init(max310x_uart_init); 1670 1671 static void __exit max310x_uart_exit(void) 1672 { 1673 #ifdef CONFIG_I2C 1674 i2c_del_driver(&max310x_i2c_driver); 1675 #endif 1676 1677 #ifdef CONFIG_SPI_MASTER 1678 spi_unregister_driver(&max310x_spi_driver); 1679 #endif 1680 1681 uart_unregister_driver(&max310x_uart); 1682 } 1683 module_exit(max310x_uart_exit); 1684 1685 MODULE_LICENSE("GPL"); 1686 MODULE_AUTHOR("Alexander Shiyan <shc_work@mail.ru>"); 1687 MODULE_DESCRIPTION("MAX310X serial driver"); 1688