1 /* 2 * This file is subject to the terms and conditions of the GNU General Public 3 * License. See the file "COPYING" in the main directory of this archive 4 * for more details. 5 * 6 * Derived from many drivers using generic_serial interface. 7 * 8 * Copyright (C) 2008 Maxime Bizon <mbizon@freebox.fr> 9 * 10 * Serial driver for BCM63xx integrated UART. 11 * 12 * Hardware flow control was _not_ tested since I only have RX/TX on 13 * my board. 14 */ 15 16 #if defined(CONFIG_SERIAL_BCM63XX_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ) 17 #define SUPPORT_SYSRQ 18 #endif 19 20 #include <linux/kernel.h> 21 #include <linux/platform_device.h> 22 #include <linux/init.h> 23 #include <linux/delay.h> 24 #include <linux/module.h> 25 #include <linux/console.h> 26 #include <linux/clk.h> 27 #include <linux/tty.h> 28 #include <linux/tty_flip.h> 29 #include <linux/sysrq.h> 30 #include <linux/serial.h> 31 #include <linux/serial_core.h> 32 33 #include <bcm63xx_irq.h> 34 #include <bcm63xx_regs.h> 35 #include <bcm63xx_io.h> 36 37 #define BCM63XX_NR_UARTS 2 38 39 static struct uart_port ports[BCM63XX_NR_UARTS]; 40 41 /* 42 * rx interrupt mask / stat 43 * 44 * mask: 45 * - rx fifo full 46 * - rx fifo above threshold 47 * - rx fifo not empty for too long 48 */ 49 #define UART_RX_INT_MASK (UART_IR_MASK(UART_IR_RXOVER) | \ 50 UART_IR_MASK(UART_IR_RXTHRESH) | \ 51 UART_IR_MASK(UART_IR_RXTIMEOUT)) 52 53 #define UART_RX_INT_STAT (UART_IR_STAT(UART_IR_RXOVER) | \ 54 UART_IR_STAT(UART_IR_RXTHRESH) | \ 55 UART_IR_STAT(UART_IR_RXTIMEOUT)) 56 57 /* 58 * tx interrupt mask / stat 59 * 60 * mask: 61 * - tx fifo empty 62 * - tx fifo below threshold 63 */ 64 #define UART_TX_INT_MASK (UART_IR_MASK(UART_IR_TXEMPTY) | \ 65 UART_IR_MASK(UART_IR_TXTRESH)) 66 67 #define UART_TX_INT_STAT (UART_IR_STAT(UART_IR_TXEMPTY) | \ 68 UART_IR_STAT(UART_IR_TXTRESH)) 69 70 /* 71 * external input interrupt 72 * 73 * mask: any edge on CTS, DCD 74 */ 75 #define UART_EXTINP_INT_MASK (UART_EXTINP_IRMASK(UART_EXTINP_IR_CTS) | \ 76 UART_EXTINP_IRMASK(UART_EXTINP_IR_DCD)) 77 78 /* 79 * handy uart register accessor 80 */ 81 static inline unsigned int bcm_uart_readl(struct uart_port *port, 82 unsigned int offset) 83 { 84 return bcm_readl(port->membase + offset); 85 } 86 87 static inline void bcm_uart_writel(struct uart_port *port, 88 unsigned int value, unsigned int offset) 89 { 90 bcm_writel(value, port->membase + offset); 91 } 92 93 /* 94 * serial core request to check if uart tx fifo is empty 95 */ 96 static unsigned int bcm_uart_tx_empty(struct uart_port *port) 97 { 98 unsigned int val; 99 100 val = bcm_uart_readl(port, UART_IR_REG); 101 return (val & UART_IR_STAT(UART_IR_TXEMPTY)) ? 1 : 0; 102 } 103 104 /* 105 * serial core request to set RTS and DTR pin state and loopback mode 106 */ 107 static void bcm_uart_set_mctrl(struct uart_port *port, unsigned int mctrl) 108 { 109 unsigned int val; 110 111 val = bcm_uart_readl(port, UART_MCTL_REG); 112 val &= ~(UART_MCTL_DTR_MASK | UART_MCTL_RTS_MASK); 113 /* invert of written value is reflected on the pin */ 114 if (!(mctrl & TIOCM_DTR)) 115 val |= UART_MCTL_DTR_MASK; 116 if (!(mctrl & TIOCM_RTS)) 117 val |= UART_MCTL_RTS_MASK; 118 bcm_uart_writel(port, val, UART_MCTL_REG); 119 120 val = bcm_uart_readl(port, UART_CTL_REG); 121 if (mctrl & TIOCM_LOOP) 122 val |= UART_CTL_LOOPBACK_MASK; 123 else 124 val &= ~UART_CTL_LOOPBACK_MASK; 125 bcm_uart_writel(port, val, UART_CTL_REG); 126 } 127 128 /* 129 * serial core request to return RI, CTS, DCD and DSR pin state 130 */ 131 static unsigned int bcm_uart_get_mctrl(struct uart_port *port) 132 { 133 unsigned int val, mctrl; 134 135 mctrl = 0; 136 val = bcm_uart_readl(port, UART_EXTINP_REG); 137 if (val & UART_EXTINP_RI_MASK) 138 mctrl |= TIOCM_RI; 139 if (val & UART_EXTINP_CTS_MASK) 140 mctrl |= TIOCM_CTS; 141 if (val & UART_EXTINP_DCD_MASK) 142 mctrl |= TIOCM_CD; 143 if (val & UART_EXTINP_DSR_MASK) 144 mctrl |= TIOCM_DSR; 145 return mctrl; 146 } 147 148 /* 149 * serial core request to disable tx ASAP (used for flow control) 150 */ 151 static void bcm_uart_stop_tx(struct uart_port *port) 152 { 153 unsigned int val; 154 155 val = bcm_uart_readl(port, UART_CTL_REG); 156 val &= ~(UART_CTL_TXEN_MASK); 157 bcm_uart_writel(port, val, UART_CTL_REG); 158 159 val = bcm_uart_readl(port, UART_IR_REG); 160 val &= ~UART_TX_INT_MASK; 161 bcm_uart_writel(port, val, UART_IR_REG); 162 } 163 164 /* 165 * serial core request to (re)enable tx 166 */ 167 static void bcm_uart_start_tx(struct uart_port *port) 168 { 169 unsigned int val; 170 171 val = bcm_uart_readl(port, UART_IR_REG); 172 val |= UART_TX_INT_MASK; 173 bcm_uart_writel(port, val, UART_IR_REG); 174 175 val = bcm_uart_readl(port, UART_CTL_REG); 176 val |= UART_CTL_TXEN_MASK; 177 bcm_uart_writel(port, val, UART_CTL_REG); 178 } 179 180 /* 181 * serial core request to stop rx, called before port shutdown 182 */ 183 static void bcm_uart_stop_rx(struct uart_port *port) 184 { 185 unsigned int val; 186 187 val = bcm_uart_readl(port, UART_IR_REG); 188 val &= ~UART_RX_INT_MASK; 189 bcm_uart_writel(port, val, UART_IR_REG); 190 } 191 192 /* 193 * serial core request to enable modem status interrupt reporting 194 */ 195 static void bcm_uart_enable_ms(struct uart_port *port) 196 { 197 unsigned int val; 198 199 val = bcm_uart_readl(port, UART_IR_REG); 200 val |= UART_IR_MASK(UART_IR_EXTIP); 201 bcm_uart_writel(port, val, UART_IR_REG); 202 } 203 204 /* 205 * serial core request to start/stop emitting break char 206 */ 207 static void bcm_uart_break_ctl(struct uart_port *port, int ctl) 208 { 209 unsigned long flags; 210 unsigned int val; 211 212 spin_lock_irqsave(&port->lock, flags); 213 214 val = bcm_uart_readl(port, UART_CTL_REG); 215 if (ctl) 216 val |= UART_CTL_XMITBRK_MASK; 217 else 218 val &= ~UART_CTL_XMITBRK_MASK; 219 bcm_uart_writel(port, val, UART_CTL_REG); 220 221 spin_unlock_irqrestore(&port->lock, flags); 222 } 223 224 /* 225 * return port type in string format 226 */ 227 static const char *bcm_uart_type(struct uart_port *port) 228 { 229 return (port->type == PORT_BCM63XX) ? "bcm63xx_uart" : NULL; 230 } 231 232 /* 233 * read all chars in rx fifo and send them to core 234 */ 235 static void bcm_uart_do_rx(struct uart_port *port) 236 { 237 struct tty_port *tty_port = &port->state->port; 238 unsigned int max_count; 239 240 /* limit number of char read in interrupt, should not be 241 * higher than fifo size anyway since we're much faster than 242 * serial port */ 243 max_count = 32; 244 do { 245 unsigned int iestat, c, cstat; 246 char flag; 247 248 /* get overrun/fifo empty information from ier 249 * register */ 250 iestat = bcm_uart_readl(port, UART_IR_REG); 251 252 if (unlikely(iestat & UART_IR_STAT(UART_IR_RXOVER))) { 253 unsigned int val; 254 255 /* fifo reset is required to clear 256 * interrupt */ 257 val = bcm_uart_readl(port, UART_CTL_REG); 258 val |= UART_CTL_RSTRXFIFO_MASK; 259 bcm_uart_writel(port, val, UART_CTL_REG); 260 261 port->icount.overrun++; 262 tty_insert_flip_char(tty_port, 0, TTY_OVERRUN); 263 } 264 265 if (!(iestat & UART_IR_STAT(UART_IR_RXNOTEMPTY))) 266 break; 267 268 cstat = c = bcm_uart_readl(port, UART_FIFO_REG); 269 port->icount.rx++; 270 flag = TTY_NORMAL; 271 c &= 0xff; 272 273 if (unlikely((cstat & UART_FIFO_ANYERR_MASK))) { 274 /* do stats first */ 275 if (cstat & UART_FIFO_BRKDET_MASK) { 276 port->icount.brk++; 277 if (uart_handle_break(port)) 278 continue; 279 } 280 281 if (cstat & UART_FIFO_PARERR_MASK) 282 port->icount.parity++; 283 if (cstat & UART_FIFO_FRAMEERR_MASK) 284 port->icount.frame++; 285 286 /* update flag wrt read_status_mask */ 287 cstat &= port->read_status_mask; 288 if (cstat & UART_FIFO_BRKDET_MASK) 289 flag = TTY_BREAK; 290 if (cstat & UART_FIFO_FRAMEERR_MASK) 291 flag = TTY_FRAME; 292 if (cstat & UART_FIFO_PARERR_MASK) 293 flag = TTY_PARITY; 294 } 295 296 if (uart_handle_sysrq_char(port, c)) 297 continue; 298 299 300 if ((cstat & port->ignore_status_mask) == 0) 301 tty_insert_flip_char(tty_port, c, flag); 302 303 } while (--max_count); 304 305 spin_unlock(&port->lock); 306 tty_flip_buffer_push(tty_port); 307 spin_lock(&port->lock); 308 } 309 310 /* 311 * fill tx fifo with chars to send, stop when fifo is about to be full 312 * or when all chars have been sent. 313 */ 314 static void bcm_uart_do_tx(struct uart_port *port) 315 { 316 struct circ_buf *xmit; 317 unsigned int val, max_count; 318 319 if (port->x_char) { 320 bcm_uart_writel(port, port->x_char, UART_FIFO_REG); 321 port->icount.tx++; 322 port->x_char = 0; 323 return; 324 } 325 326 if (uart_tx_stopped(port)) { 327 bcm_uart_stop_tx(port); 328 return; 329 } 330 331 xmit = &port->state->xmit; 332 if (uart_circ_empty(xmit)) 333 goto txq_empty; 334 335 val = bcm_uart_readl(port, UART_MCTL_REG); 336 val = (val & UART_MCTL_TXFIFOFILL_MASK) >> UART_MCTL_TXFIFOFILL_SHIFT; 337 max_count = port->fifosize - val; 338 339 while (max_count--) { 340 unsigned int c; 341 342 c = xmit->buf[xmit->tail]; 343 bcm_uart_writel(port, c, UART_FIFO_REG); 344 xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1); 345 port->icount.tx++; 346 if (uart_circ_empty(xmit)) 347 break; 348 } 349 350 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) 351 uart_write_wakeup(port); 352 353 if (uart_circ_empty(xmit)) 354 goto txq_empty; 355 return; 356 357 txq_empty: 358 /* nothing to send, disable transmit interrupt */ 359 val = bcm_uart_readl(port, UART_IR_REG); 360 val &= ~UART_TX_INT_MASK; 361 bcm_uart_writel(port, val, UART_IR_REG); 362 return; 363 } 364 365 /* 366 * process uart interrupt 367 */ 368 static irqreturn_t bcm_uart_interrupt(int irq, void *dev_id) 369 { 370 struct uart_port *port; 371 unsigned int irqstat; 372 373 port = dev_id; 374 spin_lock(&port->lock); 375 376 irqstat = bcm_uart_readl(port, UART_IR_REG); 377 if (irqstat & UART_RX_INT_STAT) 378 bcm_uart_do_rx(port); 379 380 if (irqstat & UART_TX_INT_STAT) 381 bcm_uart_do_tx(port); 382 383 if (irqstat & UART_IR_MASK(UART_IR_EXTIP)) { 384 unsigned int estat; 385 386 estat = bcm_uart_readl(port, UART_EXTINP_REG); 387 if (estat & UART_EXTINP_IRSTAT(UART_EXTINP_IR_CTS)) 388 uart_handle_cts_change(port, 389 estat & UART_EXTINP_CTS_MASK); 390 if (estat & UART_EXTINP_IRSTAT(UART_EXTINP_IR_DCD)) 391 uart_handle_dcd_change(port, 392 estat & UART_EXTINP_DCD_MASK); 393 } 394 395 spin_unlock(&port->lock); 396 return IRQ_HANDLED; 397 } 398 399 /* 400 * enable rx & tx operation on uart 401 */ 402 static void bcm_uart_enable(struct uart_port *port) 403 { 404 unsigned int val; 405 406 val = bcm_uart_readl(port, UART_CTL_REG); 407 val |= (UART_CTL_BRGEN_MASK | UART_CTL_TXEN_MASK | UART_CTL_RXEN_MASK); 408 bcm_uart_writel(port, val, UART_CTL_REG); 409 } 410 411 /* 412 * disable rx & tx operation on uart 413 */ 414 static void bcm_uart_disable(struct uart_port *port) 415 { 416 unsigned int val; 417 418 val = bcm_uart_readl(port, UART_CTL_REG); 419 val &= ~(UART_CTL_BRGEN_MASK | UART_CTL_TXEN_MASK | 420 UART_CTL_RXEN_MASK); 421 bcm_uart_writel(port, val, UART_CTL_REG); 422 } 423 424 /* 425 * clear all unread data in rx fifo and unsent data in tx fifo 426 */ 427 static void bcm_uart_flush(struct uart_port *port) 428 { 429 unsigned int val; 430 431 /* empty rx and tx fifo */ 432 val = bcm_uart_readl(port, UART_CTL_REG); 433 val |= UART_CTL_RSTRXFIFO_MASK | UART_CTL_RSTTXFIFO_MASK; 434 bcm_uart_writel(port, val, UART_CTL_REG); 435 436 /* read any pending char to make sure all irq status are 437 * cleared */ 438 (void)bcm_uart_readl(port, UART_FIFO_REG); 439 } 440 441 /* 442 * serial core request to initialize uart and start rx operation 443 */ 444 static int bcm_uart_startup(struct uart_port *port) 445 { 446 unsigned int val; 447 int ret; 448 449 /* mask all irq and flush port */ 450 bcm_uart_disable(port); 451 bcm_uart_writel(port, 0, UART_IR_REG); 452 bcm_uart_flush(port); 453 454 /* clear any pending external input interrupt */ 455 (void)bcm_uart_readl(port, UART_EXTINP_REG); 456 457 /* set rx/tx fifo thresh to fifo half size */ 458 val = bcm_uart_readl(port, UART_MCTL_REG); 459 val &= ~(UART_MCTL_RXFIFOTHRESH_MASK | UART_MCTL_TXFIFOTHRESH_MASK); 460 val |= (port->fifosize / 2) << UART_MCTL_RXFIFOTHRESH_SHIFT; 461 val |= (port->fifosize / 2) << UART_MCTL_TXFIFOTHRESH_SHIFT; 462 bcm_uart_writel(port, val, UART_MCTL_REG); 463 464 /* set rx fifo timeout to 1 char time */ 465 val = bcm_uart_readl(port, UART_CTL_REG); 466 val &= ~UART_CTL_RXTMOUTCNT_MASK; 467 val |= 1 << UART_CTL_RXTMOUTCNT_SHIFT; 468 bcm_uart_writel(port, val, UART_CTL_REG); 469 470 /* report any edge on dcd and cts */ 471 val = UART_EXTINP_INT_MASK; 472 val |= UART_EXTINP_DCD_NOSENSE_MASK; 473 val |= UART_EXTINP_CTS_NOSENSE_MASK; 474 bcm_uart_writel(port, val, UART_EXTINP_REG); 475 476 /* register irq and enable rx interrupts */ 477 ret = request_irq(port->irq, bcm_uart_interrupt, 0, 478 bcm_uart_type(port), port); 479 if (ret) 480 return ret; 481 bcm_uart_writel(port, UART_RX_INT_MASK, UART_IR_REG); 482 bcm_uart_enable(port); 483 return 0; 484 } 485 486 /* 487 * serial core request to flush & disable uart 488 */ 489 static void bcm_uart_shutdown(struct uart_port *port) 490 { 491 unsigned long flags; 492 493 spin_lock_irqsave(&port->lock, flags); 494 bcm_uart_writel(port, 0, UART_IR_REG); 495 spin_unlock_irqrestore(&port->lock, flags); 496 497 bcm_uart_disable(port); 498 bcm_uart_flush(port); 499 free_irq(port->irq, port); 500 } 501 502 /* 503 * serial core request to change current uart setting 504 */ 505 static void bcm_uart_set_termios(struct uart_port *port, 506 struct ktermios *new, 507 struct ktermios *old) 508 { 509 unsigned int ctl, baud, quot, ier; 510 unsigned long flags; 511 512 spin_lock_irqsave(&port->lock, flags); 513 514 /* disable uart while changing speed */ 515 bcm_uart_disable(port); 516 bcm_uart_flush(port); 517 518 /* update Control register */ 519 ctl = bcm_uart_readl(port, UART_CTL_REG); 520 ctl &= ~UART_CTL_BITSPERSYM_MASK; 521 522 switch (new->c_cflag & CSIZE) { 523 case CS5: 524 ctl |= (0 << UART_CTL_BITSPERSYM_SHIFT); 525 break; 526 case CS6: 527 ctl |= (1 << UART_CTL_BITSPERSYM_SHIFT); 528 break; 529 case CS7: 530 ctl |= (2 << UART_CTL_BITSPERSYM_SHIFT); 531 break; 532 default: 533 ctl |= (3 << UART_CTL_BITSPERSYM_SHIFT); 534 break; 535 } 536 537 ctl &= ~UART_CTL_STOPBITS_MASK; 538 if (new->c_cflag & CSTOPB) 539 ctl |= UART_CTL_STOPBITS_2; 540 else 541 ctl |= UART_CTL_STOPBITS_1; 542 543 ctl &= ~(UART_CTL_RXPAREN_MASK | UART_CTL_TXPAREN_MASK); 544 if (new->c_cflag & PARENB) 545 ctl |= (UART_CTL_RXPAREN_MASK | UART_CTL_TXPAREN_MASK); 546 ctl &= ~(UART_CTL_RXPAREVEN_MASK | UART_CTL_TXPAREVEN_MASK); 547 if (new->c_cflag & PARODD) 548 ctl |= (UART_CTL_RXPAREVEN_MASK | UART_CTL_TXPAREVEN_MASK); 549 bcm_uart_writel(port, ctl, UART_CTL_REG); 550 551 /* update Baudword register */ 552 baud = uart_get_baud_rate(port, new, old, 0, port->uartclk / 16); 553 quot = uart_get_divisor(port, baud) - 1; 554 bcm_uart_writel(port, quot, UART_BAUD_REG); 555 556 /* update Interrupt register */ 557 ier = bcm_uart_readl(port, UART_IR_REG); 558 559 ier &= ~UART_IR_MASK(UART_IR_EXTIP); 560 if (UART_ENABLE_MS(port, new->c_cflag)) 561 ier |= UART_IR_MASK(UART_IR_EXTIP); 562 563 bcm_uart_writel(port, ier, UART_IR_REG); 564 565 /* update read/ignore mask */ 566 port->read_status_mask = UART_FIFO_VALID_MASK; 567 if (new->c_iflag & INPCK) { 568 port->read_status_mask |= UART_FIFO_FRAMEERR_MASK; 569 port->read_status_mask |= UART_FIFO_PARERR_MASK; 570 } 571 if (new->c_iflag & (BRKINT)) 572 port->read_status_mask |= UART_FIFO_BRKDET_MASK; 573 574 port->ignore_status_mask = 0; 575 if (new->c_iflag & IGNPAR) 576 port->ignore_status_mask |= UART_FIFO_PARERR_MASK; 577 if (new->c_iflag & IGNBRK) 578 port->ignore_status_mask |= UART_FIFO_BRKDET_MASK; 579 if (!(new->c_cflag & CREAD)) 580 port->ignore_status_mask |= UART_FIFO_VALID_MASK; 581 582 uart_update_timeout(port, new->c_cflag, baud); 583 bcm_uart_enable(port); 584 spin_unlock_irqrestore(&port->lock, flags); 585 } 586 587 /* 588 * serial core request to claim uart iomem 589 */ 590 static int bcm_uart_request_port(struct uart_port *port) 591 { 592 unsigned int size; 593 594 size = RSET_UART_SIZE; 595 if (!request_mem_region(port->mapbase, size, "bcm63xx")) { 596 dev_err(port->dev, "Memory region busy\n"); 597 return -EBUSY; 598 } 599 600 port->membase = ioremap(port->mapbase, size); 601 if (!port->membase) { 602 dev_err(port->dev, "Unable to map registers\n"); 603 release_mem_region(port->mapbase, size); 604 return -EBUSY; 605 } 606 return 0; 607 } 608 609 /* 610 * serial core request to release uart iomem 611 */ 612 static void bcm_uart_release_port(struct uart_port *port) 613 { 614 release_mem_region(port->mapbase, RSET_UART_SIZE); 615 iounmap(port->membase); 616 } 617 618 /* 619 * serial core request to do any port required autoconfiguration 620 */ 621 static void bcm_uart_config_port(struct uart_port *port, int flags) 622 { 623 if (flags & UART_CONFIG_TYPE) { 624 if (bcm_uart_request_port(port)) 625 return; 626 port->type = PORT_BCM63XX; 627 } 628 } 629 630 /* 631 * serial core request to check that port information in serinfo are 632 * suitable 633 */ 634 static int bcm_uart_verify_port(struct uart_port *port, 635 struct serial_struct *serinfo) 636 { 637 if (port->type != PORT_BCM63XX) 638 return -EINVAL; 639 if (port->irq != serinfo->irq) 640 return -EINVAL; 641 if (port->iotype != serinfo->io_type) 642 return -EINVAL; 643 if (port->mapbase != (unsigned long)serinfo->iomem_base) 644 return -EINVAL; 645 return 0; 646 } 647 648 /* serial core callbacks */ 649 static struct uart_ops bcm_uart_ops = { 650 .tx_empty = bcm_uart_tx_empty, 651 .get_mctrl = bcm_uart_get_mctrl, 652 .set_mctrl = bcm_uart_set_mctrl, 653 .start_tx = bcm_uart_start_tx, 654 .stop_tx = bcm_uart_stop_tx, 655 .stop_rx = bcm_uart_stop_rx, 656 .enable_ms = bcm_uart_enable_ms, 657 .break_ctl = bcm_uart_break_ctl, 658 .startup = bcm_uart_startup, 659 .shutdown = bcm_uart_shutdown, 660 .set_termios = bcm_uart_set_termios, 661 .type = bcm_uart_type, 662 .release_port = bcm_uart_release_port, 663 .request_port = bcm_uart_request_port, 664 .config_port = bcm_uart_config_port, 665 .verify_port = bcm_uart_verify_port, 666 }; 667 668 669 670 #ifdef CONFIG_SERIAL_BCM63XX_CONSOLE 671 static inline void wait_for_xmitr(struct uart_port *port) 672 { 673 unsigned int tmout; 674 675 /* Wait up to 10ms for the character(s) to be sent. */ 676 tmout = 10000; 677 while (--tmout) { 678 unsigned int val; 679 680 val = bcm_uart_readl(port, UART_IR_REG); 681 if (val & UART_IR_STAT(UART_IR_TXEMPTY)) 682 break; 683 udelay(1); 684 } 685 686 /* Wait up to 1s for flow control if necessary */ 687 if (port->flags & UPF_CONS_FLOW) { 688 tmout = 1000000; 689 while (--tmout) { 690 unsigned int val; 691 692 val = bcm_uart_readl(port, UART_EXTINP_REG); 693 if (val & UART_EXTINP_CTS_MASK) 694 break; 695 udelay(1); 696 } 697 } 698 } 699 700 /* 701 * output given char 702 */ 703 static void bcm_console_putchar(struct uart_port *port, int ch) 704 { 705 wait_for_xmitr(port); 706 bcm_uart_writel(port, ch, UART_FIFO_REG); 707 } 708 709 /* 710 * console core request to output given string 711 */ 712 static void bcm_console_write(struct console *co, const char *s, 713 unsigned int count) 714 { 715 struct uart_port *port; 716 unsigned long flags; 717 int locked; 718 719 port = &ports[co->index]; 720 721 local_irq_save(flags); 722 if (port->sysrq) { 723 /* bcm_uart_interrupt() already took the lock */ 724 locked = 0; 725 } else if (oops_in_progress) { 726 locked = spin_trylock(&port->lock); 727 } else { 728 spin_lock(&port->lock); 729 locked = 1; 730 } 731 732 /* call helper to deal with \r\n */ 733 uart_console_write(port, s, count, bcm_console_putchar); 734 735 /* and wait for char to be transmitted */ 736 wait_for_xmitr(port); 737 738 if (locked) 739 spin_unlock(&port->lock); 740 local_irq_restore(flags); 741 } 742 743 /* 744 * console core request to setup given console, find matching uart 745 * port and setup it. 746 */ 747 static int bcm_console_setup(struct console *co, char *options) 748 { 749 struct uart_port *port; 750 int baud = 9600; 751 int bits = 8; 752 int parity = 'n'; 753 int flow = 'n'; 754 755 if (co->index < 0 || co->index >= BCM63XX_NR_UARTS) 756 return -EINVAL; 757 port = &ports[co->index]; 758 if (!port->membase) 759 return -ENODEV; 760 if (options) 761 uart_parse_options(options, &baud, &parity, &bits, &flow); 762 763 return uart_set_options(port, co, baud, parity, bits, flow); 764 } 765 766 static struct uart_driver bcm_uart_driver; 767 768 static struct console bcm63xx_console = { 769 .name = "ttyS", 770 .write = bcm_console_write, 771 .device = uart_console_device, 772 .setup = bcm_console_setup, 773 .flags = CON_PRINTBUFFER, 774 .index = -1, 775 .data = &bcm_uart_driver, 776 }; 777 778 static int __init bcm63xx_console_init(void) 779 { 780 register_console(&bcm63xx_console); 781 return 0; 782 } 783 784 console_initcall(bcm63xx_console_init); 785 786 #define BCM63XX_CONSOLE (&bcm63xx_console) 787 #else 788 #define BCM63XX_CONSOLE NULL 789 #endif /* CONFIG_SERIAL_BCM63XX_CONSOLE */ 790 791 static struct uart_driver bcm_uart_driver = { 792 .owner = THIS_MODULE, 793 .driver_name = "bcm63xx_uart", 794 .dev_name = "ttyS", 795 .major = TTY_MAJOR, 796 .minor = 64, 797 .nr = BCM63XX_NR_UARTS, 798 .cons = BCM63XX_CONSOLE, 799 }; 800 801 /* 802 * platform driver probe/remove callback 803 */ 804 static int bcm_uart_probe(struct platform_device *pdev) 805 { 806 struct resource *res_mem, *res_irq; 807 struct uart_port *port; 808 struct clk *clk; 809 int ret; 810 811 if (pdev->id < 0 || pdev->id >= BCM63XX_NR_UARTS) 812 return -EINVAL; 813 814 if (ports[pdev->id].membase) 815 return -EBUSY; 816 817 res_mem = platform_get_resource(pdev, IORESOURCE_MEM, 0); 818 if (!res_mem) 819 return -ENODEV; 820 821 res_irq = platform_get_resource(pdev, IORESOURCE_IRQ, 0); 822 if (!res_irq) 823 return -ENODEV; 824 825 clk = clk_get(&pdev->dev, "periph"); 826 if (IS_ERR(clk)) 827 return -ENODEV; 828 829 port = &ports[pdev->id]; 830 memset(port, 0, sizeof(*port)); 831 port->iotype = UPIO_MEM; 832 port->mapbase = res_mem->start; 833 port->irq = res_irq->start; 834 port->ops = &bcm_uart_ops; 835 port->flags = UPF_BOOT_AUTOCONF; 836 port->dev = &pdev->dev; 837 port->fifosize = 16; 838 port->uartclk = clk_get_rate(clk) / 2; 839 port->line = pdev->id; 840 clk_put(clk); 841 842 ret = uart_add_one_port(&bcm_uart_driver, port); 843 if (ret) { 844 ports[pdev->id].membase = 0; 845 return ret; 846 } 847 platform_set_drvdata(pdev, port); 848 return 0; 849 } 850 851 static int bcm_uart_remove(struct platform_device *pdev) 852 { 853 struct uart_port *port; 854 855 port = platform_get_drvdata(pdev); 856 uart_remove_one_port(&bcm_uart_driver, port); 857 /* mark port as free */ 858 ports[pdev->id].membase = 0; 859 return 0; 860 } 861 862 /* 863 * platform driver stuff 864 */ 865 static struct platform_driver bcm_uart_platform_driver = { 866 .probe = bcm_uart_probe, 867 .remove = bcm_uart_remove, 868 .driver = { 869 .owner = THIS_MODULE, 870 .name = "bcm63xx_uart", 871 }, 872 }; 873 874 static int __init bcm_uart_init(void) 875 { 876 int ret; 877 878 ret = uart_register_driver(&bcm_uart_driver); 879 if (ret) 880 return ret; 881 882 ret = platform_driver_register(&bcm_uart_platform_driver); 883 if (ret) 884 uart_unregister_driver(&bcm_uart_driver); 885 886 return ret; 887 } 888 889 static void __exit bcm_uart_exit(void) 890 { 891 platform_driver_unregister(&bcm_uart_platform_driver); 892 uart_unregister_driver(&bcm_uart_driver); 893 } 894 895 module_init(bcm_uart_init); 896 module_exit(bcm_uart_exit); 897 898 MODULE_AUTHOR("Maxime Bizon <mbizon@freebox.fr>"); 899 MODULE_DESCRIPTION("Broadcom 63<xx integrated uart driver"); 900 MODULE_LICENSE("GPL"); 901