1 // SPDX-License-Identifier: GPL-2.0
2 /*
3  * Derived from many drivers using generic_serial interface.
4  *
5  * Copyright (C) 2008 Maxime Bizon <mbizon@freebox.fr>
6  *
7  *  Serial driver for BCM63xx integrated UART.
8  *
9  * Hardware flow control was _not_ tested since I only have RX/TX on
10  * my board.
11  */
12 
13 #include <linux/kernel.h>
14 #include <linux/platform_device.h>
15 #include <linux/init.h>
16 #include <linux/delay.h>
17 #include <linux/module.h>
18 #include <linux/console.h>
19 #include <linux/clk.h>
20 #include <linux/tty.h>
21 #include <linux/tty_flip.h>
22 #include <linux/sysrq.h>
23 #include <linux/serial.h>
24 #include <linux/serial_core.h>
25 #include <linux/serial_bcm63xx.h>
26 #include <linux/io.h>
27 #include <linux/of.h>
28 
29 #define BCM63XX_NR_UARTS	2
30 
31 static struct uart_port ports[BCM63XX_NR_UARTS];
32 
33 /*
34  * rx interrupt mask / stat
35  *
36  * mask:
37  *  - rx fifo full
38  *  - rx fifo above threshold
39  *  - rx fifo not empty for too long
40  */
41 #define UART_RX_INT_MASK	(UART_IR_MASK(UART_IR_RXOVER) |		\
42 				UART_IR_MASK(UART_IR_RXTHRESH) |	\
43 				UART_IR_MASK(UART_IR_RXTIMEOUT))
44 
45 #define UART_RX_INT_STAT	(UART_IR_STAT(UART_IR_RXOVER) |		\
46 				UART_IR_STAT(UART_IR_RXTHRESH) |	\
47 				UART_IR_STAT(UART_IR_RXTIMEOUT))
48 
49 /*
50  * tx interrupt mask / stat
51  *
52  * mask:
53  * - tx fifo empty
54  * - tx fifo below threshold
55  */
56 #define UART_TX_INT_MASK	(UART_IR_MASK(UART_IR_TXEMPTY) |	\
57 				UART_IR_MASK(UART_IR_TXTRESH))
58 
59 #define UART_TX_INT_STAT	(UART_IR_STAT(UART_IR_TXEMPTY) |	\
60 				UART_IR_STAT(UART_IR_TXTRESH))
61 
62 /*
63  * external input interrupt
64  *
65  * mask: any edge on CTS, DCD
66  */
67 #define UART_EXTINP_INT_MASK	(UART_EXTINP_IRMASK(UART_EXTINP_IR_CTS) | \
68 				 UART_EXTINP_IRMASK(UART_EXTINP_IR_DCD))
69 
70 /*
71  * handy uart register accessor
72  */
73 static inline unsigned int bcm_uart_readl(struct uart_port *port,
74 					 unsigned int offset)
75 {
76 	return __raw_readl(port->membase + offset);
77 }
78 
79 static inline void bcm_uart_writel(struct uart_port *port,
80 				  unsigned int value, unsigned int offset)
81 {
82 	__raw_writel(value, port->membase + offset);
83 }
84 
85 /*
86  * serial core request to check if uart tx fifo is empty
87  */
88 static unsigned int bcm_uart_tx_empty(struct uart_port *port)
89 {
90 	unsigned int val;
91 
92 	val = bcm_uart_readl(port, UART_IR_REG);
93 	return (val & UART_IR_STAT(UART_IR_TXEMPTY)) ? 1 : 0;
94 }
95 
96 /*
97  * serial core request to set RTS and DTR pin state and loopback mode
98  */
99 static void bcm_uart_set_mctrl(struct uart_port *port, unsigned int mctrl)
100 {
101 	unsigned int val;
102 
103 	val = bcm_uart_readl(port, UART_MCTL_REG);
104 	val &= ~(UART_MCTL_DTR_MASK | UART_MCTL_RTS_MASK);
105 	/* invert of written value is reflected on the pin */
106 	if (!(mctrl & TIOCM_DTR))
107 		val |= UART_MCTL_DTR_MASK;
108 	if (!(mctrl & TIOCM_RTS))
109 		val |= UART_MCTL_RTS_MASK;
110 	bcm_uart_writel(port, val, UART_MCTL_REG);
111 
112 	val = bcm_uart_readl(port, UART_CTL_REG);
113 	if (mctrl & TIOCM_LOOP)
114 		val |= UART_CTL_LOOPBACK_MASK;
115 	else
116 		val &= ~UART_CTL_LOOPBACK_MASK;
117 	bcm_uart_writel(port, val, UART_CTL_REG);
118 }
119 
120 /*
121  * serial core request to return RI, CTS, DCD and DSR pin state
122  */
123 static unsigned int bcm_uart_get_mctrl(struct uart_port *port)
124 {
125 	unsigned int val, mctrl;
126 
127 	mctrl = 0;
128 	val = bcm_uart_readl(port, UART_EXTINP_REG);
129 	if (val & UART_EXTINP_RI_MASK)
130 		mctrl |= TIOCM_RI;
131 	if (val & UART_EXTINP_CTS_MASK)
132 		mctrl |= TIOCM_CTS;
133 	if (val & UART_EXTINP_DCD_MASK)
134 		mctrl |= TIOCM_CD;
135 	if (val & UART_EXTINP_DSR_MASK)
136 		mctrl |= TIOCM_DSR;
137 	return mctrl;
138 }
139 
140 /*
141  * serial core request to disable tx ASAP (used for flow control)
142  */
143 static void bcm_uart_stop_tx(struct uart_port *port)
144 {
145 	unsigned int val;
146 
147 	val = bcm_uart_readl(port, UART_CTL_REG);
148 	val &= ~(UART_CTL_TXEN_MASK);
149 	bcm_uart_writel(port, val, UART_CTL_REG);
150 
151 	val = bcm_uart_readl(port, UART_IR_REG);
152 	val &= ~UART_TX_INT_MASK;
153 	bcm_uart_writel(port, val, UART_IR_REG);
154 }
155 
156 /*
157  * serial core request to (re)enable tx
158  */
159 static void bcm_uart_start_tx(struct uart_port *port)
160 {
161 	unsigned int val;
162 
163 	val = bcm_uart_readl(port, UART_IR_REG);
164 	val |= UART_TX_INT_MASK;
165 	bcm_uart_writel(port, val, UART_IR_REG);
166 
167 	val = bcm_uart_readl(port, UART_CTL_REG);
168 	val |= UART_CTL_TXEN_MASK;
169 	bcm_uart_writel(port, val, UART_CTL_REG);
170 }
171 
172 /*
173  * serial core request to stop rx, called before port shutdown
174  */
175 static void bcm_uart_stop_rx(struct uart_port *port)
176 {
177 	unsigned int val;
178 
179 	val = bcm_uart_readl(port, UART_IR_REG);
180 	val &= ~UART_RX_INT_MASK;
181 	bcm_uart_writel(port, val, UART_IR_REG);
182 }
183 
184 /*
185  * serial core request to enable modem status interrupt reporting
186  */
187 static void bcm_uart_enable_ms(struct uart_port *port)
188 {
189 	unsigned int val;
190 
191 	val = bcm_uart_readl(port, UART_IR_REG);
192 	val |= UART_IR_MASK(UART_IR_EXTIP);
193 	bcm_uart_writel(port, val, UART_IR_REG);
194 }
195 
196 /*
197  * serial core request to start/stop emitting break char
198  */
199 static void bcm_uart_break_ctl(struct uart_port *port, int ctl)
200 {
201 	unsigned long flags;
202 	unsigned int val;
203 
204 	spin_lock_irqsave(&port->lock, flags);
205 
206 	val = bcm_uart_readl(port, UART_CTL_REG);
207 	if (ctl)
208 		val |= UART_CTL_XMITBRK_MASK;
209 	else
210 		val &= ~UART_CTL_XMITBRK_MASK;
211 	bcm_uart_writel(port, val, UART_CTL_REG);
212 
213 	spin_unlock_irqrestore(&port->lock, flags);
214 }
215 
216 /*
217  * return port type in string format
218  */
219 static const char *bcm_uart_type(struct uart_port *port)
220 {
221 	return (port->type == PORT_BCM63XX) ? "bcm63xx_uart" : NULL;
222 }
223 
224 /*
225  * read all chars in rx fifo and send them to core
226  */
227 static void bcm_uart_do_rx(struct uart_port *port)
228 {
229 	struct tty_port *tty_port = &port->state->port;
230 	unsigned int max_count;
231 
232 	/* limit number of char read in interrupt, should not be
233 	 * higher than fifo size anyway since we're much faster than
234 	 * serial port */
235 	max_count = 32;
236 	do {
237 		unsigned int iestat, c, cstat;
238 		char flag;
239 
240 		/* get overrun/fifo empty information from ier
241 		 * register */
242 		iestat = bcm_uart_readl(port, UART_IR_REG);
243 
244 		if (unlikely(iestat & UART_IR_STAT(UART_IR_RXOVER))) {
245 			unsigned int val;
246 
247 			/* fifo reset is required to clear
248 			 * interrupt */
249 			val = bcm_uart_readl(port, UART_CTL_REG);
250 			val |= UART_CTL_RSTRXFIFO_MASK;
251 			bcm_uart_writel(port, val, UART_CTL_REG);
252 
253 			port->icount.overrun++;
254 			tty_insert_flip_char(tty_port, 0, TTY_OVERRUN);
255 		}
256 
257 		if (!(iestat & UART_IR_STAT(UART_IR_RXNOTEMPTY)))
258 			break;
259 
260 		cstat = c = bcm_uart_readl(port, UART_FIFO_REG);
261 		port->icount.rx++;
262 		flag = TTY_NORMAL;
263 		c &= 0xff;
264 
265 		if (unlikely((cstat & UART_FIFO_ANYERR_MASK))) {
266 			/* do stats first */
267 			if (cstat & UART_FIFO_BRKDET_MASK) {
268 				port->icount.brk++;
269 				if (uart_handle_break(port))
270 					continue;
271 			}
272 
273 			if (cstat & UART_FIFO_PARERR_MASK)
274 				port->icount.parity++;
275 			if (cstat & UART_FIFO_FRAMEERR_MASK)
276 				port->icount.frame++;
277 
278 			/* update flag wrt read_status_mask */
279 			cstat &= port->read_status_mask;
280 			if (cstat & UART_FIFO_BRKDET_MASK)
281 				flag = TTY_BREAK;
282 			if (cstat & UART_FIFO_FRAMEERR_MASK)
283 				flag = TTY_FRAME;
284 			if (cstat & UART_FIFO_PARERR_MASK)
285 				flag = TTY_PARITY;
286 		}
287 
288 		if (uart_handle_sysrq_char(port, c))
289 			continue;
290 
291 
292 		if ((cstat & port->ignore_status_mask) == 0)
293 			tty_insert_flip_char(tty_port, c, flag);
294 
295 	} while (--max_count);
296 
297 	tty_flip_buffer_push(tty_port);
298 }
299 
300 /*
301  * fill tx fifo with chars to send, stop when fifo is about to be full
302  * or when all chars have been sent.
303  */
304 static void bcm_uart_do_tx(struct uart_port *port)
305 {
306 	struct circ_buf *xmit;
307 	unsigned int val, max_count;
308 
309 	if (port->x_char) {
310 		bcm_uart_writel(port, port->x_char, UART_FIFO_REG);
311 		port->icount.tx++;
312 		port->x_char = 0;
313 		return;
314 	}
315 
316 	if (uart_tx_stopped(port)) {
317 		bcm_uart_stop_tx(port);
318 		return;
319 	}
320 
321 	xmit = &port->state->xmit;
322 	if (uart_circ_empty(xmit))
323 		goto txq_empty;
324 
325 	val = bcm_uart_readl(port, UART_MCTL_REG);
326 	val = (val & UART_MCTL_TXFIFOFILL_MASK) >> UART_MCTL_TXFIFOFILL_SHIFT;
327 	max_count = port->fifosize - val;
328 
329 	while (max_count--) {
330 		unsigned int c;
331 
332 		c = xmit->buf[xmit->tail];
333 		bcm_uart_writel(port, c, UART_FIFO_REG);
334 		xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
335 		port->icount.tx++;
336 		if (uart_circ_empty(xmit))
337 			break;
338 	}
339 
340 	if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
341 		uart_write_wakeup(port);
342 
343 	if (uart_circ_empty(xmit))
344 		goto txq_empty;
345 	return;
346 
347 txq_empty:
348 	/* nothing to send, disable transmit interrupt */
349 	val = bcm_uart_readl(port, UART_IR_REG);
350 	val &= ~UART_TX_INT_MASK;
351 	bcm_uart_writel(port, val, UART_IR_REG);
352 	return;
353 }
354 
355 /*
356  * process uart interrupt
357  */
358 static irqreturn_t bcm_uart_interrupt(int irq, void *dev_id)
359 {
360 	struct uart_port *port;
361 	unsigned int irqstat;
362 
363 	port = dev_id;
364 	spin_lock(&port->lock);
365 
366 	irqstat = bcm_uart_readl(port, UART_IR_REG);
367 	if (irqstat & UART_RX_INT_STAT)
368 		bcm_uart_do_rx(port);
369 
370 	if (irqstat & UART_TX_INT_STAT)
371 		bcm_uart_do_tx(port);
372 
373 	if (irqstat & UART_IR_MASK(UART_IR_EXTIP)) {
374 		unsigned int estat;
375 
376 		estat = bcm_uart_readl(port, UART_EXTINP_REG);
377 		if (estat & UART_EXTINP_IRSTAT(UART_EXTINP_IR_CTS))
378 			uart_handle_cts_change(port,
379 					       estat & UART_EXTINP_CTS_MASK);
380 		if (estat & UART_EXTINP_IRSTAT(UART_EXTINP_IR_DCD))
381 			uart_handle_dcd_change(port,
382 					       estat & UART_EXTINP_DCD_MASK);
383 	}
384 
385 	spin_unlock(&port->lock);
386 	return IRQ_HANDLED;
387 }
388 
389 /*
390  * enable rx & tx operation on uart
391  */
392 static void bcm_uart_enable(struct uart_port *port)
393 {
394 	unsigned int val;
395 
396 	val = bcm_uart_readl(port, UART_CTL_REG);
397 	val |= (UART_CTL_BRGEN_MASK | UART_CTL_TXEN_MASK | UART_CTL_RXEN_MASK);
398 	bcm_uart_writel(port, val, UART_CTL_REG);
399 }
400 
401 /*
402  * disable rx & tx operation on uart
403  */
404 static void bcm_uart_disable(struct uart_port *port)
405 {
406 	unsigned int val;
407 
408 	val = bcm_uart_readl(port, UART_CTL_REG);
409 	val &= ~(UART_CTL_BRGEN_MASK | UART_CTL_TXEN_MASK |
410 		 UART_CTL_RXEN_MASK);
411 	bcm_uart_writel(port, val, UART_CTL_REG);
412 }
413 
414 /*
415  * clear all unread data in rx fifo and unsent data in tx fifo
416  */
417 static void bcm_uart_flush(struct uart_port *port)
418 {
419 	unsigned int val;
420 
421 	/* empty rx and tx fifo */
422 	val = bcm_uart_readl(port, UART_CTL_REG);
423 	val |= UART_CTL_RSTRXFIFO_MASK | UART_CTL_RSTTXFIFO_MASK;
424 	bcm_uart_writel(port, val, UART_CTL_REG);
425 
426 	/* read any pending char to make sure all irq status are
427 	 * cleared */
428 	(void)bcm_uart_readl(port, UART_FIFO_REG);
429 }
430 
431 /*
432  * serial core request to initialize uart and start rx operation
433  */
434 static int bcm_uart_startup(struct uart_port *port)
435 {
436 	unsigned int val;
437 	int ret;
438 
439 	/* mask all irq and flush port */
440 	bcm_uart_disable(port);
441 	bcm_uart_writel(port, 0, UART_IR_REG);
442 	bcm_uart_flush(port);
443 
444 	/* clear any pending external input interrupt */
445 	(void)bcm_uart_readl(port, UART_EXTINP_REG);
446 
447 	/* set rx/tx fifo thresh to fifo half size */
448 	val = bcm_uart_readl(port, UART_MCTL_REG);
449 	val &= ~(UART_MCTL_RXFIFOTHRESH_MASK | UART_MCTL_TXFIFOTHRESH_MASK);
450 	val |= (port->fifosize / 2) << UART_MCTL_RXFIFOTHRESH_SHIFT;
451 	val |= (port->fifosize / 2) << UART_MCTL_TXFIFOTHRESH_SHIFT;
452 	bcm_uart_writel(port, val, UART_MCTL_REG);
453 
454 	/* set rx fifo timeout to 1 char time */
455 	val = bcm_uart_readl(port, UART_CTL_REG);
456 	val &= ~UART_CTL_RXTMOUTCNT_MASK;
457 	val |= 1 << UART_CTL_RXTMOUTCNT_SHIFT;
458 	bcm_uart_writel(port, val, UART_CTL_REG);
459 
460 	/* report any edge on dcd and cts */
461 	val = UART_EXTINP_INT_MASK;
462 	val |= UART_EXTINP_DCD_NOSENSE_MASK;
463 	val |= UART_EXTINP_CTS_NOSENSE_MASK;
464 	bcm_uart_writel(port, val, UART_EXTINP_REG);
465 
466 	/* register irq and enable rx interrupts */
467 	ret = request_irq(port->irq, bcm_uart_interrupt, 0,
468 			  dev_name(port->dev), port);
469 	if (ret)
470 		return ret;
471 	bcm_uart_writel(port, UART_RX_INT_MASK, UART_IR_REG);
472 	bcm_uart_enable(port);
473 	return 0;
474 }
475 
476 /*
477  * serial core request to flush & disable uart
478  */
479 static void bcm_uart_shutdown(struct uart_port *port)
480 {
481 	unsigned long flags;
482 
483 	spin_lock_irqsave(&port->lock, flags);
484 	bcm_uart_writel(port, 0, UART_IR_REG);
485 	spin_unlock_irqrestore(&port->lock, flags);
486 
487 	bcm_uart_disable(port);
488 	bcm_uart_flush(port);
489 	free_irq(port->irq, port);
490 }
491 
492 /*
493  * serial core request to change current uart setting
494  */
495 static void bcm_uart_set_termios(struct uart_port *port,
496 				 struct ktermios *new,
497 				 struct ktermios *old)
498 {
499 	unsigned int ctl, baud, quot, ier;
500 	unsigned long flags;
501 	int tries;
502 
503 	spin_lock_irqsave(&port->lock, flags);
504 
505 	/* Drain the hot tub fully before we power it off for the winter. */
506 	for (tries = 3; !bcm_uart_tx_empty(port) && tries; tries--)
507 		mdelay(10);
508 
509 	/* disable uart while changing speed */
510 	bcm_uart_disable(port);
511 	bcm_uart_flush(port);
512 
513 	/* update Control register */
514 	ctl = bcm_uart_readl(port, UART_CTL_REG);
515 	ctl &= ~UART_CTL_BITSPERSYM_MASK;
516 
517 	switch (new->c_cflag & CSIZE) {
518 	case CS5:
519 		ctl |= (0 << UART_CTL_BITSPERSYM_SHIFT);
520 		break;
521 	case CS6:
522 		ctl |= (1 << UART_CTL_BITSPERSYM_SHIFT);
523 		break;
524 	case CS7:
525 		ctl |= (2 << UART_CTL_BITSPERSYM_SHIFT);
526 		break;
527 	default:
528 		ctl |= (3 << UART_CTL_BITSPERSYM_SHIFT);
529 		break;
530 	}
531 
532 	ctl &= ~UART_CTL_STOPBITS_MASK;
533 	if (new->c_cflag & CSTOPB)
534 		ctl |= UART_CTL_STOPBITS_2;
535 	else
536 		ctl |= UART_CTL_STOPBITS_1;
537 
538 	ctl &= ~(UART_CTL_RXPAREN_MASK | UART_CTL_TXPAREN_MASK);
539 	if (new->c_cflag & PARENB)
540 		ctl |= (UART_CTL_RXPAREN_MASK | UART_CTL_TXPAREN_MASK);
541 	ctl &= ~(UART_CTL_RXPAREVEN_MASK | UART_CTL_TXPAREVEN_MASK);
542 	if (new->c_cflag & PARODD)
543 		ctl |= (UART_CTL_RXPAREVEN_MASK | UART_CTL_TXPAREVEN_MASK);
544 	bcm_uart_writel(port, ctl, UART_CTL_REG);
545 
546 	/* update Baudword register */
547 	baud = uart_get_baud_rate(port, new, old, 0, port->uartclk / 16);
548 	quot = uart_get_divisor(port, baud) - 1;
549 	bcm_uart_writel(port, quot, UART_BAUD_REG);
550 
551 	/* update Interrupt register */
552 	ier = bcm_uart_readl(port, UART_IR_REG);
553 
554 	ier &= ~UART_IR_MASK(UART_IR_EXTIP);
555 	if (UART_ENABLE_MS(port, new->c_cflag))
556 		ier |= UART_IR_MASK(UART_IR_EXTIP);
557 
558 	bcm_uart_writel(port, ier, UART_IR_REG);
559 
560 	/* update read/ignore mask */
561 	port->read_status_mask = UART_FIFO_VALID_MASK;
562 	if (new->c_iflag & INPCK) {
563 		port->read_status_mask |= UART_FIFO_FRAMEERR_MASK;
564 		port->read_status_mask |= UART_FIFO_PARERR_MASK;
565 	}
566 	if (new->c_iflag & (IGNBRK | BRKINT))
567 		port->read_status_mask |= UART_FIFO_BRKDET_MASK;
568 
569 	port->ignore_status_mask = 0;
570 	if (new->c_iflag & IGNPAR)
571 		port->ignore_status_mask |= UART_FIFO_PARERR_MASK;
572 	if (new->c_iflag & IGNBRK)
573 		port->ignore_status_mask |= UART_FIFO_BRKDET_MASK;
574 	if (!(new->c_cflag & CREAD))
575 		port->ignore_status_mask |= UART_FIFO_VALID_MASK;
576 
577 	uart_update_timeout(port, new->c_cflag, baud);
578 	bcm_uart_enable(port);
579 	spin_unlock_irqrestore(&port->lock, flags);
580 }
581 
582 /*
583  * serial core request to claim uart iomem
584  */
585 static int bcm_uart_request_port(struct uart_port *port)
586 {
587 	/* UARTs always present */
588 	return 0;
589 }
590 
591 /*
592  * serial core request to release uart iomem
593  */
594 static void bcm_uart_release_port(struct uart_port *port)
595 {
596 	/* Nothing to release ... */
597 }
598 
599 /*
600  * serial core request to do any port required autoconfiguration
601  */
602 static void bcm_uart_config_port(struct uart_port *port, int flags)
603 {
604 	if (flags & UART_CONFIG_TYPE) {
605 		if (bcm_uart_request_port(port))
606 			return;
607 		port->type = PORT_BCM63XX;
608 	}
609 }
610 
611 /*
612  * serial core request to check that port information in serinfo are
613  * suitable
614  */
615 static int bcm_uart_verify_port(struct uart_port *port,
616 				struct serial_struct *serinfo)
617 {
618 	if (port->type != PORT_BCM63XX)
619 		return -EINVAL;
620 	if (port->irq != serinfo->irq)
621 		return -EINVAL;
622 	if (port->iotype != serinfo->io_type)
623 		return -EINVAL;
624 	if (port->mapbase != (unsigned long)serinfo->iomem_base)
625 		return -EINVAL;
626 	return 0;
627 }
628 
629 /* serial core callbacks */
630 static const struct uart_ops bcm_uart_ops = {
631 	.tx_empty	= bcm_uart_tx_empty,
632 	.get_mctrl	= bcm_uart_get_mctrl,
633 	.set_mctrl	= bcm_uart_set_mctrl,
634 	.start_tx	= bcm_uart_start_tx,
635 	.stop_tx	= bcm_uart_stop_tx,
636 	.stop_rx	= bcm_uart_stop_rx,
637 	.enable_ms	= bcm_uart_enable_ms,
638 	.break_ctl	= bcm_uart_break_ctl,
639 	.startup	= bcm_uart_startup,
640 	.shutdown	= bcm_uart_shutdown,
641 	.set_termios	= bcm_uart_set_termios,
642 	.type		= bcm_uart_type,
643 	.release_port	= bcm_uart_release_port,
644 	.request_port	= bcm_uart_request_port,
645 	.config_port	= bcm_uart_config_port,
646 	.verify_port	= bcm_uart_verify_port,
647 };
648 
649 
650 
651 #ifdef CONFIG_SERIAL_BCM63XX_CONSOLE
652 static void wait_for_xmitr(struct uart_port *port)
653 {
654 	unsigned int tmout;
655 
656 	/* Wait up to 10ms for the character(s) to be sent. */
657 	tmout = 10000;
658 	while (--tmout) {
659 		unsigned int val;
660 
661 		val = bcm_uart_readl(port, UART_IR_REG);
662 		if (val & UART_IR_STAT(UART_IR_TXEMPTY))
663 			break;
664 		udelay(1);
665 	}
666 
667 	/* Wait up to 1s for flow control if necessary */
668 	if (port->flags & UPF_CONS_FLOW) {
669 		tmout = 1000000;
670 		while (--tmout) {
671 			unsigned int val;
672 
673 			val = bcm_uart_readl(port, UART_EXTINP_REG);
674 			if (val & UART_EXTINP_CTS_MASK)
675 				break;
676 			udelay(1);
677 		}
678 	}
679 }
680 
681 /*
682  * output given char
683  */
684 static void bcm_console_putchar(struct uart_port *port, int ch)
685 {
686 	wait_for_xmitr(port);
687 	bcm_uart_writel(port, ch, UART_FIFO_REG);
688 }
689 
690 /*
691  * console core request to output given string
692  */
693 static void bcm_console_write(struct console *co, const char *s,
694 			      unsigned int count)
695 {
696 	struct uart_port *port;
697 	unsigned long flags;
698 	int locked;
699 
700 	port = &ports[co->index];
701 
702 	local_irq_save(flags);
703 	if (port->sysrq) {
704 		/* bcm_uart_interrupt() already took the lock */
705 		locked = 0;
706 	} else if (oops_in_progress) {
707 		locked = spin_trylock(&port->lock);
708 	} else {
709 		spin_lock(&port->lock);
710 		locked = 1;
711 	}
712 
713 	/* call helper to deal with \r\n */
714 	uart_console_write(port, s, count, bcm_console_putchar);
715 
716 	/* and wait for char to be transmitted */
717 	wait_for_xmitr(port);
718 
719 	if (locked)
720 		spin_unlock(&port->lock);
721 	local_irq_restore(flags);
722 }
723 
724 /*
725  * console core request to setup given console, find matching uart
726  * port and setup it.
727  */
728 static int bcm_console_setup(struct console *co, char *options)
729 {
730 	struct uart_port *port;
731 	int baud = 9600;
732 	int bits = 8;
733 	int parity = 'n';
734 	int flow = 'n';
735 
736 	if (co->index < 0 || co->index >= BCM63XX_NR_UARTS)
737 		return -EINVAL;
738 	port = &ports[co->index];
739 	if (!port->membase)
740 		return -ENODEV;
741 	if (options)
742 		uart_parse_options(options, &baud, &parity, &bits, &flow);
743 
744 	return uart_set_options(port, co, baud, parity, bits, flow);
745 }
746 
747 static struct uart_driver bcm_uart_driver;
748 
749 static struct console bcm63xx_console = {
750 	.name		= "ttyS",
751 	.write		= bcm_console_write,
752 	.device		= uart_console_device,
753 	.setup		= bcm_console_setup,
754 	.flags		= CON_PRINTBUFFER,
755 	.index		= -1,
756 	.data		= &bcm_uart_driver,
757 };
758 
759 static int __init bcm63xx_console_init(void)
760 {
761 	register_console(&bcm63xx_console);
762 	return 0;
763 }
764 
765 console_initcall(bcm63xx_console_init);
766 
767 static void bcm_early_write(struct console *con, const char *s, unsigned n)
768 {
769 	struct earlycon_device *dev = con->data;
770 
771 	uart_console_write(&dev->port, s, n, bcm_console_putchar);
772 	wait_for_xmitr(&dev->port);
773 }
774 
775 static int __init bcm_early_console_setup(struct earlycon_device *device,
776 					  const char *opt)
777 {
778 	if (!device->port.membase)
779 		return -ENODEV;
780 
781 	device->con->write = bcm_early_write;
782 	return 0;
783 }
784 
785 OF_EARLYCON_DECLARE(bcm63xx_uart, "brcm,bcm6345-uart", bcm_early_console_setup);
786 
787 #define BCM63XX_CONSOLE	(&bcm63xx_console)
788 #else
789 #define BCM63XX_CONSOLE	NULL
790 #endif /* CONFIG_SERIAL_BCM63XX_CONSOLE */
791 
792 static struct uart_driver bcm_uart_driver = {
793 	.owner		= THIS_MODULE,
794 	.driver_name	= "bcm63xx_uart",
795 	.dev_name	= "ttyS",
796 	.major		= TTY_MAJOR,
797 	.minor		= 64,
798 	.nr		= BCM63XX_NR_UARTS,
799 	.cons		= BCM63XX_CONSOLE,
800 };
801 
802 /*
803  * platform driver probe/remove callback
804  */
805 static int bcm_uart_probe(struct platform_device *pdev)
806 {
807 	struct resource *res_mem, *res_irq;
808 	struct uart_port *port;
809 	struct clk *clk;
810 	int ret;
811 
812 	if (pdev->dev.of_node) {
813 		pdev->id = of_alias_get_id(pdev->dev.of_node, "serial");
814 
815 		if (pdev->id < 0)
816 			pdev->id = of_alias_get_id(pdev->dev.of_node, "uart");
817 	}
818 
819 	if (pdev->id < 0 || pdev->id >= BCM63XX_NR_UARTS)
820 		return -EINVAL;
821 
822 	port = &ports[pdev->id];
823 	if (port->membase)
824 		return -EBUSY;
825 	memset(port, 0, sizeof(*port));
826 
827 	res_mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
828 	if (!res_mem)
829 		return -ENODEV;
830 
831 	port->mapbase = res_mem->start;
832 	port->membase = devm_ioremap_resource(&pdev->dev, res_mem);
833 	if (IS_ERR(port->membase))
834 		return PTR_ERR(port->membase);
835 
836 	res_irq = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
837 	if (!res_irq)
838 		return -ENODEV;
839 
840 	clk = clk_get(&pdev->dev, "refclk");
841 	if (IS_ERR(clk) && pdev->dev.of_node)
842 		clk = of_clk_get(pdev->dev.of_node, 0);
843 
844 	if (IS_ERR(clk))
845 		return -ENODEV;
846 
847 	port->iotype = UPIO_MEM;
848 	port->irq = res_irq->start;
849 	port->ops = &bcm_uart_ops;
850 	port->flags = UPF_BOOT_AUTOCONF;
851 	port->dev = &pdev->dev;
852 	port->fifosize = 16;
853 	port->uartclk = clk_get_rate(clk) / 2;
854 	port->line = pdev->id;
855 	port->has_sysrq = IS_ENABLED(CONFIG_SERIAL_BCM63XX_CONSOLE);
856 	clk_put(clk);
857 
858 	ret = uart_add_one_port(&bcm_uart_driver, port);
859 	if (ret) {
860 		ports[pdev->id].membase = NULL;
861 		return ret;
862 	}
863 	platform_set_drvdata(pdev, port);
864 	return 0;
865 }
866 
867 static int bcm_uart_remove(struct platform_device *pdev)
868 {
869 	struct uart_port *port;
870 
871 	port = platform_get_drvdata(pdev);
872 	uart_remove_one_port(&bcm_uart_driver, port);
873 	/* mark port as free */
874 	ports[pdev->id].membase = NULL;
875 	return 0;
876 }
877 
878 static const struct of_device_id bcm63xx_of_match[] = {
879 	{ .compatible = "brcm,bcm6345-uart" },
880 	{ /* sentinel */ }
881 };
882 MODULE_DEVICE_TABLE(of, bcm63xx_of_match);
883 
884 /*
885  * platform driver stuff
886  */
887 static struct platform_driver bcm_uart_platform_driver = {
888 	.probe	= bcm_uart_probe,
889 	.remove	= bcm_uart_remove,
890 	.driver	= {
891 		.name  = "bcm63xx_uart",
892 		.of_match_table = bcm63xx_of_match,
893 	},
894 };
895 
896 static int __init bcm_uart_init(void)
897 {
898 	int ret;
899 
900 	ret = uart_register_driver(&bcm_uart_driver);
901 	if (ret)
902 		return ret;
903 
904 	ret = platform_driver_register(&bcm_uart_platform_driver);
905 	if (ret)
906 		uart_unregister_driver(&bcm_uart_driver);
907 
908 	return ret;
909 }
910 
911 static void __exit bcm_uart_exit(void)
912 {
913 	platform_driver_unregister(&bcm_uart_platform_driver);
914 	uart_unregister_driver(&bcm_uart_driver);
915 }
916 
917 module_init(bcm_uart_init);
918 module_exit(bcm_uart_exit);
919 
920 MODULE_AUTHOR("Maxime Bizon <mbizon@freebox.fr>");
921 MODULE_DESCRIPTION("Broadcom 63xx integrated uart driver");
922 MODULE_LICENSE("GPL");
923