1 // SPDX-License-Identifier: GPL-2.0+ 2 /* 3 * Driver for Atmel AT91 Serial ports 4 * Copyright (C) 2003 Rick Bronson 5 * 6 * Based on drivers/char/serial_sa1100.c, by Deep Blue Solutions Ltd. 7 * Based on drivers/char/serial.c, by Linus Torvalds, Theodore Ts'o. 8 * 9 * DMA support added by Chip Coldwell. 10 */ 11 #include <linux/tty.h> 12 #include <linux/ioport.h> 13 #include <linux/slab.h> 14 #include <linux/init.h> 15 #include <linux/serial.h> 16 #include <linux/clk.h> 17 #include <linux/console.h> 18 #include <linux/sysrq.h> 19 #include <linux/tty_flip.h> 20 #include <linux/platform_device.h> 21 #include <linux/of.h> 22 #include <linux/of_device.h> 23 #include <linux/dma-mapping.h> 24 #include <linux/dmaengine.h> 25 #include <linux/atmel_pdc.h> 26 #include <linux/uaccess.h> 27 #include <linux/platform_data/atmel.h> 28 #include <linux/timer.h> 29 #include <linux/err.h> 30 #include <linux/irq.h> 31 #include <linux/suspend.h> 32 #include <linux/mm.h> 33 #include <linux/io.h> 34 35 #include <asm/div64.h> 36 #include <asm/ioctls.h> 37 38 #define PDC_BUFFER_SIZE 512 39 /* Revisit: We should calculate this based on the actual port settings */ 40 #define PDC_RX_TIMEOUT (3 * 10) /* 3 bytes */ 41 42 /* The minium number of data FIFOs should be able to contain */ 43 #define ATMEL_MIN_FIFO_SIZE 8 44 /* 45 * These two offsets are substracted from the RX FIFO size to define the RTS 46 * high and low thresholds 47 */ 48 #define ATMEL_RTS_HIGH_OFFSET 16 49 #define ATMEL_RTS_LOW_OFFSET 20 50 51 #include <linux/serial_core.h> 52 53 #include "serial_mctrl_gpio.h" 54 #include "atmel_serial.h" 55 56 static void atmel_start_rx(struct uart_port *port); 57 static void atmel_stop_rx(struct uart_port *port); 58 59 #ifdef CONFIG_SERIAL_ATMEL_TTYAT 60 61 /* Use device name ttyAT, major 204 and minor 154-169. This is necessary if we 62 * should coexist with the 8250 driver, such as if we have an external 16C550 63 * UART. */ 64 #define SERIAL_ATMEL_MAJOR 204 65 #define MINOR_START 154 66 #define ATMEL_DEVICENAME "ttyAT" 67 68 #else 69 70 /* Use device name ttyS, major 4, minor 64-68. This is the usual serial port 71 * name, but it is legally reserved for the 8250 driver. */ 72 #define SERIAL_ATMEL_MAJOR TTY_MAJOR 73 #define MINOR_START 64 74 #define ATMEL_DEVICENAME "ttyS" 75 76 #endif 77 78 #define ATMEL_ISR_PASS_LIMIT 256 79 80 struct atmel_dma_buffer { 81 unsigned char *buf; 82 dma_addr_t dma_addr; 83 unsigned int dma_size; 84 unsigned int ofs; 85 }; 86 87 struct atmel_uart_char { 88 u16 status; 89 u16 ch; 90 }; 91 92 /* 93 * Be careful, the real size of the ring buffer is 94 * sizeof(atmel_uart_char) * ATMEL_SERIAL_RINGSIZE. It means that ring buffer 95 * can contain up to 1024 characters in PIO mode and up to 4096 characters in 96 * DMA mode. 97 */ 98 #define ATMEL_SERIAL_RINGSIZE 1024 99 100 /* 101 * at91: 6 USARTs and one DBGU port (SAM9260) 102 * samx7: 3 USARTs and 5 UARTs 103 */ 104 #define ATMEL_MAX_UART 8 105 106 /* 107 * We wrap our port structure around the generic uart_port. 108 */ 109 struct atmel_uart_port { 110 struct uart_port uart; /* uart */ 111 struct clk *clk; /* uart clock */ 112 int may_wakeup; /* cached value of device_may_wakeup for times we need to disable it */ 113 u32 backup_imr; /* IMR saved during suspend */ 114 int break_active; /* break being received */ 115 116 bool use_dma_rx; /* enable DMA receiver */ 117 bool use_pdc_rx; /* enable PDC receiver */ 118 short pdc_rx_idx; /* current PDC RX buffer */ 119 struct atmel_dma_buffer pdc_rx[2]; /* PDC receier */ 120 121 bool use_dma_tx; /* enable DMA transmitter */ 122 bool use_pdc_tx; /* enable PDC transmitter */ 123 struct atmel_dma_buffer pdc_tx; /* PDC transmitter */ 124 125 spinlock_t lock_tx; /* port lock */ 126 spinlock_t lock_rx; /* port lock */ 127 struct dma_chan *chan_tx; 128 struct dma_chan *chan_rx; 129 struct dma_async_tx_descriptor *desc_tx; 130 struct dma_async_tx_descriptor *desc_rx; 131 dma_cookie_t cookie_tx; 132 dma_cookie_t cookie_rx; 133 struct scatterlist sg_tx; 134 struct scatterlist sg_rx; 135 struct tasklet_struct tasklet_rx; 136 struct tasklet_struct tasklet_tx; 137 atomic_t tasklet_shutdown; 138 unsigned int irq_status_prev; 139 unsigned int tx_len; 140 141 struct circ_buf rx_ring; 142 143 struct mctrl_gpios *gpios; 144 u32 backup_mode; /* MR saved during iso7816 operations */ 145 u32 backup_brgr; /* BRGR saved during iso7816 operations */ 146 unsigned int tx_done_mask; 147 u32 fifo_size; 148 u32 rts_high; 149 u32 rts_low; 150 bool ms_irq_enabled; 151 u32 rtor; /* address of receiver timeout register if it exists */ 152 bool has_frac_baudrate; 153 bool has_hw_timer; 154 struct timer_list uart_timer; 155 156 bool tx_stopped; 157 bool suspended; 158 unsigned int pending; 159 unsigned int pending_status; 160 spinlock_t lock_suspended; 161 162 bool hd_start_rx; /* can start RX during half-duplex operation */ 163 164 /* ISO7816 */ 165 unsigned int fidi_min; 166 unsigned int fidi_max; 167 168 #ifdef CONFIG_PM 169 struct { 170 u32 cr; 171 u32 mr; 172 u32 imr; 173 u32 brgr; 174 u32 rtor; 175 u32 ttgr; 176 u32 fmr; 177 u32 fimr; 178 } cache; 179 #endif 180 181 int (*prepare_rx)(struct uart_port *port); 182 int (*prepare_tx)(struct uart_port *port); 183 void (*schedule_rx)(struct uart_port *port); 184 void (*schedule_tx)(struct uart_port *port); 185 void (*release_rx)(struct uart_port *port); 186 void (*release_tx)(struct uart_port *port); 187 }; 188 189 static struct atmel_uart_port atmel_ports[ATMEL_MAX_UART]; 190 static DECLARE_BITMAP(atmel_ports_in_use, ATMEL_MAX_UART); 191 192 #if defined(CONFIG_OF) 193 static const struct of_device_id atmel_serial_dt_ids[] = { 194 { .compatible = "atmel,at91rm9200-usart-serial" }, 195 { /* sentinel */ } 196 }; 197 #endif 198 199 static inline struct atmel_uart_port * 200 to_atmel_uart_port(struct uart_port *uart) 201 { 202 return container_of(uart, struct atmel_uart_port, uart); 203 } 204 205 static inline u32 atmel_uart_readl(struct uart_port *port, u32 reg) 206 { 207 return __raw_readl(port->membase + reg); 208 } 209 210 static inline void atmel_uart_writel(struct uart_port *port, u32 reg, u32 value) 211 { 212 __raw_writel(value, port->membase + reg); 213 } 214 215 static inline u8 atmel_uart_read_char(struct uart_port *port) 216 { 217 return __raw_readb(port->membase + ATMEL_US_RHR); 218 } 219 220 static inline void atmel_uart_write_char(struct uart_port *port, u8 value) 221 { 222 __raw_writeb(value, port->membase + ATMEL_US_THR); 223 } 224 225 static inline int atmel_uart_is_half_duplex(struct uart_port *port) 226 { 227 return ((port->rs485.flags & SER_RS485_ENABLED) && 228 !(port->rs485.flags & SER_RS485_RX_DURING_TX)) || 229 (port->iso7816.flags & SER_ISO7816_ENABLED); 230 } 231 232 #ifdef CONFIG_SERIAL_ATMEL_PDC 233 static bool atmel_use_pdc_rx(struct uart_port *port) 234 { 235 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 236 237 return atmel_port->use_pdc_rx; 238 } 239 240 static bool atmel_use_pdc_tx(struct uart_port *port) 241 { 242 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 243 244 return atmel_port->use_pdc_tx; 245 } 246 #else 247 static bool atmel_use_pdc_rx(struct uart_port *port) 248 { 249 return false; 250 } 251 252 static bool atmel_use_pdc_tx(struct uart_port *port) 253 { 254 return false; 255 } 256 #endif 257 258 static bool atmel_use_dma_tx(struct uart_port *port) 259 { 260 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 261 262 return atmel_port->use_dma_tx; 263 } 264 265 static bool atmel_use_dma_rx(struct uart_port *port) 266 { 267 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 268 269 return atmel_port->use_dma_rx; 270 } 271 272 static bool atmel_use_fifo(struct uart_port *port) 273 { 274 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 275 276 return atmel_port->fifo_size; 277 } 278 279 static void atmel_tasklet_schedule(struct atmel_uart_port *atmel_port, 280 struct tasklet_struct *t) 281 { 282 if (!atomic_read(&atmel_port->tasklet_shutdown)) 283 tasklet_schedule(t); 284 } 285 286 /* Enable or disable the rs485 support */ 287 static int atmel_config_rs485(struct uart_port *port, 288 struct serial_rs485 *rs485conf) 289 { 290 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 291 unsigned int mode; 292 293 /* Disable interrupts */ 294 atmel_uart_writel(port, ATMEL_US_IDR, atmel_port->tx_done_mask); 295 296 mode = atmel_uart_readl(port, ATMEL_US_MR); 297 298 /* Resetting serial mode to RS232 (0x0) */ 299 mode &= ~ATMEL_US_USMODE; 300 301 port->rs485 = *rs485conf; 302 303 if (rs485conf->flags & SER_RS485_ENABLED) { 304 dev_dbg(port->dev, "Setting UART to RS485\n"); 305 if (port->rs485.flags & SER_RS485_RX_DURING_TX) 306 atmel_port->tx_done_mask = ATMEL_US_TXRDY; 307 else 308 atmel_port->tx_done_mask = ATMEL_US_TXEMPTY; 309 310 atmel_uart_writel(port, ATMEL_US_TTGR, 311 rs485conf->delay_rts_after_send); 312 mode |= ATMEL_US_USMODE_RS485; 313 } else { 314 dev_dbg(port->dev, "Setting UART to RS232\n"); 315 if (atmel_use_pdc_tx(port)) 316 atmel_port->tx_done_mask = ATMEL_US_ENDTX | 317 ATMEL_US_TXBUFE; 318 else 319 atmel_port->tx_done_mask = ATMEL_US_TXRDY; 320 } 321 atmel_uart_writel(port, ATMEL_US_MR, mode); 322 323 /* Enable interrupts */ 324 atmel_uart_writel(port, ATMEL_US_IER, atmel_port->tx_done_mask); 325 326 return 0; 327 } 328 329 static unsigned int atmel_calc_cd(struct uart_port *port, 330 struct serial_iso7816 *iso7816conf) 331 { 332 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 333 unsigned int cd; 334 u64 mck_rate; 335 336 mck_rate = (u64)clk_get_rate(atmel_port->clk); 337 do_div(mck_rate, iso7816conf->clk); 338 cd = mck_rate; 339 return cd; 340 } 341 342 static unsigned int atmel_calc_fidi(struct uart_port *port, 343 struct serial_iso7816 *iso7816conf) 344 { 345 u64 fidi = 0; 346 347 if (iso7816conf->sc_fi && iso7816conf->sc_di) { 348 fidi = (u64)iso7816conf->sc_fi; 349 do_div(fidi, iso7816conf->sc_di); 350 } 351 return (u32)fidi; 352 } 353 354 /* Enable or disable the iso7816 support */ 355 /* Called with interrupts disabled */ 356 static int atmel_config_iso7816(struct uart_port *port, 357 struct serial_iso7816 *iso7816conf) 358 { 359 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 360 unsigned int mode; 361 unsigned int cd, fidi; 362 int ret = 0; 363 364 /* Disable interrupts */ 365 atmel_uart_writel(port, ATMEL_US_IDR, atmel_port->tx_done_mask); 366 367 mode = atmel_uart_readl(port, ATMEL_US_MR); 368 369 if (iso7816conf->flags & SER_ISO7816_ENABLED) { 370 mode &= ~ATMEL_US_USMODE; 371 372 if (iso7816conf->tg > 255) { 373 dev_err(port->dev, "ISO7816: Timeguard exceeding 255\n"); 374 memset(iso7816conf, 0, sizeof(struct serial_iso7816)); 375 ret = -EINVAL; 376 goto err_out; 377 } 378 379 if ((iso7816conf->flags & SER_ISO7816_T_PARAM) 380 == SER_ISO7816_T(0)) { 381 mode |= ATMEL_US_USMODE_ISO7816_T0 | ATMEL_US_DSNACK; 382 } else if ((iso7816conf->flags & SER_ISO7816_T_PARAM) 383 == SER_ISO7816_T(1)) { 384 mode |= ATMEL_US_USMODE_ISO7816_T1 | ATMEL_US_INACK; 385 } else { 386 dev_err(port->dev, "ISO7816: Type not supported\n"); 387 memset(iso7816conf, 0, sizeof(struct serial_iso7816)); 388 ret = -EINVAL; 389 goto err_out; 390 } 391 392 mode &= ~(ATMEL_US_USCLKS | ATMEL_US_NBSTOP | ATMEL_US_PAR); 393 394 /* select mck clock, and output */ 395 mode |= ATMEL_US_USCLKS_MCK | ATMEL_US_CLKO; 396 /* set parity for normal/inverse mode + max iterations */ 397 mode |= ATMEL_US_PAR_EVEN | ATMEL_US_NBSTOP_1 | ATMEL_US_MAX_ITER(3); 398 399 cd = atmel_calc_cd(port, iso7816conf); 400 fidi = atmel_calc_fidi(port, iso7816conf); 401 if (fidi == 0) { 402 dev_warn(port->dev, "ISO7816 fidi = 0, Generator generates no signal\n"); 403 } else if (fidi < atmel_port->fidi_min 404 || fidi > atmel_port->fidi_max) { 405 dev_err(port->dev, "ISO7816 fidi = %u, value not supported\n", fidi); 406 memset(iso7816conf, 0, sizeof(struct serial_iso7816)); 407 ret = -EINVAL; 408 goto err_out; 409 } 410 411 if (!(port->iso7816.flags & SER_ISO7816_ENABLED)) { 412 /* port not yet in iso7816 mode: store configuration */ 413 atmel_port->backup_mode = atmel_uart_readl(port, ATMEL_US_MR); 414 atmel_port->backup_brgr = atmel_uart_readl(port, ATMEL_US_BRGR); 415 } 416 417 atmel_uart_writel(port, ATMEL_US_TTGR, iso7816conf->tg); 418 atmel_uart_writel(port, ATMEL_US_BRGR, cd); 419 atmel_uart_writel(port, ATMEL_US_FIDI, fidi); 420 421 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXDIS | ATMEL_US_RXEN); 422 atmel_port->tx_done_mask = ATMEL_US_TXEMPTY | ATMEL_US_NACK | ATMEL_US_ITERATION; 423 } else { 424 dev_dbg(port->dev, "Setting UART back to RS232\n"); 425 /* back to last RS232 settings */ 426 mode = atmel_port->backup_mode; 427 memset(iso7816conf, 0, sizeof(struct serial_iso7816)); 428 atmel_uart_writel(port, ATMEL_US_TTGR, 0); 429 atmel_uart_writel(port, ATMEL_US_BRGR, atmel_port->backup_brgr); 430 atmel_uart_writel(port, ATMEL_US_FIDI, 0x174); 431 432 if (atmel_use_pdc_tx(port)) 433 atmel_port->tx_done_mask = ATMEL_US_ENDTX | 434 ATMEL_US_TXBUFE; 435 else 436 atmel_port->tx_done_mask = ATMEL_US_TXRDY; 437 } 438 439 port->iso7816 = *iso7816conf; 440 441 atmel_uart_writel(port, ATMEL_US_MR, mode); 442 443 err_out: 444 /* Enable interrupts */ 445 atmel_uart_writel(port, ATMEL_US_IER, atmel_port->tx_done_mask); 446 447 return ret; 448 } 449 450 /* 451 * Return TIOCSER_TEMT when transmitter FIFO and Shift register is empty. 452 */ 453 static u_int atmel_tx_empty(struct uart_port *port) 454 { 455 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 456 457 if (atmel_port->tx_stopped) 458 return TIOCSER_TEMT; 459 return (atmel_uart_readl(port, ATMEL_US_CSR) & ATMEL_US_TXEMPTY) ? 460 TIOCSER_TEMT : 461 0; 462 } 463 464 /* 465 * Set state of the modem control output lines 466 */ 467 static void atmel_set_mctrl(struct uart_port *port, u_int mctrl) 468 { 469 unsigned int control = 0; 470 unsigned int mode = atmel_uart_readl(port, ATMEL_US_MR); 471 unsigned int rts_paused, rts_ready; 472 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 473 474 /* override mode to RS485 if needed, otherwise keep the current mode */ 475 if (port->rs485.flags & SER_RS485_ENABLED) { 476 atmel_uart_writel(port, ATMEL_US_TTGR, 477 port->rs485.delay_rts_after_send); 478 mode &= ~ATMEL_US_USMODE; 479 mode |= ATMEL_US_USMODE_RS485; 480 } 481 482 /* set the RTS line state according to the mode */ 483 if ((mode & ATMEL_US_USMODE) == ATMEL_US_USMODE_HWHS) { 484 /* force RTS line to high level */ 485 rts_paused = ATMEL_US_RTSEN; 486 487 /* give the control of the RTS line back to the hardware */ 488 rts_ready = ATMEL_US_RTSDIS; 489 } else { 490 /* force RTS line to high level */ 491 rts_paused = ATMEL_US_RTSDIS; 492 493 /* force RTS line to low level */ 494 rts_ready = ATMEL_US_RTSEN; 495 } 496 497 if (mctrl & TIOCM_RTS) 498 control |= rts_ready; 499 else 500 control |= rts_paused; 501 502 if (mctrl & TIOCM_DTR) 503 control |= ATMEL_US_DTREN; 504 else 505 control |= ATMEL_US_DTRDIS; 506 507 atmel_uart_writel(port, ATMEL_US_CR, control); 508 509 mctrl_gpio_set(atmel_port->gpios, mctrl); 510 511 /* Local loopback mode? */ 512 mode &= ~ATMEL_US_CHMODE; 513 if (mctrl & TIOCM_LOOP) 514 mode |= ATMEL_US_CHMODE_LOC_LOOP; 515 else 516 mode |= ATMEL_US_CHMODE_NORMAL; 517 518 atmel_uart_writel(port, ATMEL_US_MR, mode); 519 } 520 521 /* 522 * Get state of the modem control input lines 523 */ 524 static u_int atmel_get_mctrl(struct uart_port *port) 525 { 526 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 527 unsigned int ret = 0, status; 528 529 status = atmel_uart_readl(port, ATMEL_US_CSR); 530 531 /* 532 * The control signals are active low. 533 */ 534 if (!(status & ATMEL_US_DCD)) 535 ret |= TIOCM_CD; 536 if (!(status & ATMEL_US_CTS)) 537 ret |= TIOCM_CTS; 538 if (!(status & ATMEL_US_DSR)) 539 ret |= TIOCM_DSR; 540 if (!(status & ATMEL_US_RI)) 541 ret |= TIOCM_RI; 542 543 return mctrl_gpio_get(atmel_port->gpios, &ret); 544 } 545 546 /* 547 * Stop transmitting. 548 */ 549 static void atmel_stop_tx(struct uart_port *port) 550 { 551 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 552 553 if (atmel_use_pdc_tx(port)) { 554 /* disable PDC transmit */ 555 atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_TXTDIS); 556 } 557 558 /* 559 * Disable the transmitter. 560 * This is mandatory when DMA is used, otherwise the DMA buffer 561 * is fully transmitted. 562 */ 563 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXDIS); 564 atmel_port->tx_stopped = true; 565 566 /* Disable interrupts */ 567 atmel_uart_writel(port, ATMEL_US_IDR, atmel_port->tx_done_mask); 568 569 if (atmel_uart_is_half_duplex(port)) 570 if (!atomic_read(&atmel_port->tasklet_shutdown)) 571 atmel_start_rx(port); 572 573 } 574 575 /* 576 * Start transmitting. 577 */ 578 static void atmel_start_tx(struct uart_port *port) 579 { 580 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 581 582 if (atmel_use_pdc_tx(port) && (atmel_uart_readl(port, ATMEL_PDC_PTSR) 583 & ATMEL_PDC_TXTEN)) 584 /* The transmitter is already running. Yes, we 585 really need this.*/ 586 return; 587 588 if (atmel_use_pdc_tx(port) || atmel_use_dma_tx(port)) 589 if (atmel_uart_is_half_duplex(port)) 590 atmel_stop_rx(port); 591 592 if (atmel_use_pdc_tx(port)) 593 /* re-enable PDC transmit */ 594 atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_TXTEN); 595 596 /* Enable interrupts */ 597 atmel_uart_writel(port, ATMEL_US_IER, atmel_port->tx_done_mask); 598 599 /* re-enable the transmitter */ 600 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXEN); 601 atmel_port->tx_stopped = false; 602 } 603 604 /* 605 * start receiving - port is in process of being opened. 606 */ 607 static void atmel_start_rx(struct uart_port *port) 608 { 609 /* reset status and receiver */ 610 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA); 611 612 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RXEN); 613 614 if (atmel_use_pdc_rx(port)) { 615 /* enable PDC controller */ 616 atmel_uart_writel(port, ATMEL_US_IER, 617 ATMEL_US_ENDRX | ATMEL_US_TIMEOUT | 618 port->read_status_mask); 619 atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_RXTEN); 620 } else { 621 atmel_uart_writel(port, ATMEL_US_IER, ATMEL_US_RXRDY); 622 } 623 } 624 625 /* 626 * Stop receiving - port is in process of being closed. 627 */ 628 static void atmel_stop_rx(struct uart_port *port) 629 { 630 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RXDIS); 631 632 if (atmel_use_pdc_rx(port)) { 633 /* disable PDC receive */ 634 atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_RXTDIS); 635 atmel_uart_writel(port, ATMEL_US_IDR, 636 ATMEL_US_ENDRX | ATMEL_US_TIMEOUT | 637 port->read_status_mask); 638 } else { 639 atmel_uart_writel(port, ATMEL_US_IDR, ATMEL_US_RXRDY); 640 } 641 } 642 643 /* 644 * Enable modem status interrupts 645 */ 646 static void atmel_enable_ms(struct uart_port *port) 647 { 648 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 649 uint32_t ier = 0; 650 651 /* 652 * Interrupt should not be enabled twice 653 */ 654 if (atmel_port->ms_irq_enabled) 655 return; 656 657 atmel_port->ms_irq_enabled = true; 658 659 if (!mctrl_gpio_to_gpiod(atmel_port->gpios, UART_GPIO_CTS)) 660 ier |= ATMEL_US_CTSIC; 661 662 if (!mctrl_gpio_to_gpiod(atmel_port->gpios, UART_GPIO_DSR)) 663 ier |= ATMEL_US_DSRIC; 664 665 if (!mctrl_gpio_to_gpiod(atmel_port->gpios, UART_GPIO_RI)) 666 ier |= ATMEL_US_RIIC; 667 668 if (!mctrl_gpio_to_gpiod(atmel_port->gpios, UART_GPIO_DCD)) 669 ier |= ATMEL_US_DCDIC; 670 671 atmel_uart_writel(port, ATMEL_US_IER, ier); 672 673 mctrl_gpio_enable_ms(atmel_port->gpios); 674 } 675 676 /* 677 * Disable modem status interrupts 678 */ 679 static void atmel_disable_ms(struct uart_port *port) 680 { 681 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 682 uint32_t idr = 0; 683 684 /* 685 * Interrupt should not be disabled twice 686 */ 687 if (!atmel_port->ms_irq_enabled) 688 return; 689 690 atmel_port->ms_irq_enabled = false; 691 692 mctrl_gpio_disable_ms(atmel_port->gpios); 693 694 if (!mctrl_gpio_to_gpiod(atmel_port->gpios, UART_GPIO_CTS)) 695 idr |= ATMEL_US_CTSIC; 696 697 if (!mctrl_gpio_to_gpiod(atmel_port->gpios, UART_GPIO_DSR)) 698 idr |= ATMEL_US_DSRIC; 699 700 if (!mctrl_gpio_to_gpiod(atmel_port->gpios, UART_GPIO_RI)) 701 idr |= ATMEL_US_RIIC; 702 703 if (!mctrl_gpio_to_gpiod(atmel_port->gpios, UART_GPIO_DCD)) 704 idr |= ATMEL_US_DCDIC; 705 706 atmel_uart_writel(port, ATMEL_US_IDR, idr); 707 } 708 709 /* 710 * Control the transmission of a break signal 711 */ 712 static void atmel_break_ctl(struct uart_port *port, int break_state) 713 { 714 if (break_state != 0) 715 /* start break */ 716 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_STTBRK); 717 else 718 /* stop break */ 719 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_STPBRK); 720 } 721 722 /* 723 * Stores the incoming character in the ring buffer 724 */ 725 static void 726 atmel_buffer_rx_char(struct uart_port *port, unsigned int status, 727 unsigned int ch) 728 { 729 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 730 struct circ_buf *ring = &atmel_port->rx_ring; 731 struct atmel_uart_char *c; 732 733 if (!CIRC_SPACE(ring->head, ring->tail, ATMEL_SERIAL_RINGSIZE)) 734 /* Buffer overflow, ignore char */ 735 return; 736 737 c = &((struct atmel_uart_char *)ring->buf)[ring->head]; 738 c->status = status; 739 c->ch = ch; 740 741 /* Make sure the character is stored before we update head. */ 742 smp_wmb(); 743 744 ring->head = (ring->head + 1) & (ATMEL_SERIAL_RINGSIZE - 1); 745 } 746 747 /* 748 * Deal with parity, framing and overrun errors. 749 */ 750 static void atmel_pdc_rxerr(struct uart_port *port, unsigned int status) 751 { 752 /* clear error */ 753 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA); 754 755 if (status & ATMEL_US_RXBRK) { 756 /* ignore side-effect */ 757 status &= ~(ATMEL_US_PARE | ATMEL_US_FRAME); 758 port->icount.brk++; 759 } 760 if (status & ATMEL_US_PARE) 761 port->icount.parity++; 762 if (status & ATMEL_US_FRAME) 763 port->icount.frame++; 764 if (status & ATMEL_US_OVRE) 765 port->icount.overrun++; 766 } 767 768 /* 769 * Characters received (called from interrupt handler) 770 */ 771 static void atmel_rx_chars(struct uart_port *port) 772 { 773 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 774 unsigned int status, ch; 775 776 status = atmel_uart_readl(port, ATMEL_US_CSR); 777 while (status & ATMEL_US_RXRDY) { 778 ch = atmel_uart_read_char(port); 779 780 /* 781 * note that the error handling code is 782 * out of the main execution path 783 */ 784 if (unlikely(status & (ATMEL_US_PARE | ATMEL_US_FRAME 785 | ATMEL_US_OVRE | ATMEL_US_RXBRK) 786 || atmel_port->break_active)) { 787 788 /* clear error */ 789 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA); 790 791 if (status & ATMEL_US_RXBRK 792 && !atmel_port->break_active) { 793 atmel_port->break_active = 1; 794 atmel_uart_writel(port, ATMEL_US_IER, 795 ATMEL_US_RXBRK); 796 } else { 797 /* 798 * This is either the end-of-break 799 * condition or we've received at 800 * least one character without RXBRK 801 * being set. In both cases, the next 802 * RXBRK will indicate start-of-break. 803 */ 804 atmel_uart_writel(port, ATMEL_US_IDR, 805 ATMEL_US_RXBRK); 806 status &= ~ATMEL_US_RXBRK; 807 atmel_port->break_active = 0; 808 } 809 } 810 811 atmel_buffer_rx_char(port, status, ch); 812 status = atmel_uart_readl(port, ATMEL_US_CSR); 813 } 814 815 atmel_tasklet_schedule(atmel_port, &atmel_port->tasklet_rx); 816 } 817 818 /* 819 * Transmit characters (called from tasklet with TXRDY interrupt 820 * disabled) 821 */ 822 static void atmel_tx_chars(struct uart_port *port) 823 { 824 struct circ_buf *xmit = &port->state->xmit; 825 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 826 827 if (port->x_char && 828 (atmel_uart_readl(port, ATMEL_US_CSR) & ATMEL_US_TXRDY)) { 829 atmel_uart_write_char(port, port->x_char); 830 port->icount.tx++; 831 port->x_char = 0; 832 } 833 if (uart_circ_empty(xmit) || uart_tx_stopped(port)) 834 return; 835 836 while (atmel_uart_readl(port, ATMEL_US_CSR) & ATMEL_US_TXRDY) { 837 atmel_uart_write_char(port, xmit->buf[xmit->tail]); 838 xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1); 839 port->icount.tx++; 840 if (uart_circ_empty(xmit)) 841 break; 842 } 843 844 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) 845 uart_write_wakeup(port); 846 847 if (!uart_circ_empty(xmit)) { 848 /* we still have characters to transmit, so we should continue 849 * transmitting them when TX is ready, regardless of 850 * mode or duplexity 851 */ 852 atmel_port->tx_done_mask |= ATMEL_US_TXRDY; 853 854 /* Enable interrupts */ 855 atmel_uart_writel(port, ATMEL_US_IER, 856 atmel_port->tx_done_mask); 857 } else { 858 if (atmel_uart_is_half_duplex(port)) 859 atmel_port->tx_done_mask &= ~ATMEL_US_TXRDY; 860 } 861 } 862 863 static void atmel_complete_tx_dma(void *arg) 864 { 865 struct atmel_uart_port *atmel_port = arg; 866 struct uart_port *port = &atmel_port->uart; 867 struct circ_buf *xmit = &port->state->xmit; 868 struct dma_chan *chan = atmel_port->chan_tx; 869 unsigned long flags; 870 871 spin_lock_irqsave(&port->lock, flags); 872 873 if (chan) 874 dmaengine_terminate_all(chan); 875 xmit->tail += atmel_port->tx_len; 876 xmit->tail &= UART_XMIT_SIZE - 1; 877 878 port->icount.tx += atmel_port->tx_len; 879 880 spin_lock_irq(&atmel_port->lock_tx); 881 async_tx_ack(atmel_port->desc_tx); 882 atmel_port->cookie_tx = -EINVAL; 883 atmel_port->desc_tx = NULL; 884 spin_unlock_irq(&atmel_port->lock_tx); 885 886 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) 887 uart_write_wakeup(port); 888 889 /* 890 * xmit is a circular buffer so, if we have just send data from 891 * xmit->tail to the end of xmit->buf, now we have to transmit the 892 * remaining data from the beginning of xmit->buf to xmit->head. 893 */ 894 if (!uart_circ_empty(xmit)) 895 atmel_tasklet_schedule(atmel_port, &atmel_port->tasklet_tx); 896 else if (atmel_uart_is_half_duplex(port)) { 897 /* 898 * DMA done, re-enable TXEMPTY and signal that we can stop 899 * TX and start RX for RS485 900 */ 901 atmel_port->hd_start_rx = true; 902 atmel_uart_writel(port, ATMEL_US_IER, 903 atmel_port->tx_done_mask); 904 } 905 906 spin_unlock_irqrestore(&port->lock, flags); 907 } 908 909 static void atmel_release_tx_dma(struct uart_port *port) 910 { 911 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 912 struct dma_chan *chan = atmel_port->chan_tx; 913 914 if (chan) { 915 dmaengine_terminate_all(chan); 916 dma_release_channel(chan); 917 dma_unmap_sg(port->dev, &atmel_port->sg_tx, 1, 918 DMA_TO_DEVICE); 919 } 920 921 atmel_port->desc_tx = NULL; 922 atmel_port->chan_tx = NULL; 923 atmel_port->cookie_tx = -EINVAL; 924 } 925 926 /* 927 * Called from tasklet with TXRDY interrupt is disabled. 928 */ 929 static void atmel_tx_dma(struct uart_port *port) 930 { 931 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 932 struct circ_buf *xmit = &port->state->xmit; 933 struct dma_chan *chan = atmel_port->chan_tx; 934 struct dma_async_tx_descriptor *desc; 935 struct scatterlist sgl[2], *sg, *sg_tx = &atmel_port->sg_tx; 936 unsigned int tx_len, part1_len, part2_len, sg_len; 937 dma_addr_t phys_addr; 938 939 /* Make sure we have an idle channel */ 940 if (atmel_port->desc_tx != NULL) 941 return; 942 943 if (!uart_circ_empty(xmit) && !uart_tx_stopped(port)) { 944 /* 945 * DMA is idle now. 946 * Port xmit buffer is already mapped, 947 * and it is one page... Just adjust 948 * offsets and lengths. Since it is a circular buffer, 949 * we have to transmit till the end, and then the rest. 950 * Take the port lock to get a 951 * consistent xmit buffer state. 952 */ 953 tx_len = CIRC_CNT_TO_END(xmit->head, 954 xmit->tail, 955 UART_XMIT_SIZE); 956 957 if (atmel_port->fifo_size) { 958 /* multi data mode */ 959 part1_len = (tx_len & ~0x3); /* DWORD access */ 960 part2_len = (tx_len & 0x3); /* BYTE access */ 961 } else { 962 /* single data (legacy) mode */ 963 part1_len = 0; 964 part2_len = tx_len; /* BYTE access only */ 965 } 966 967 sg_init_table(sgl, 2); 968 sg_len = 0; 969 phys_addr = sg_dma_address(sg_tx) + xmit->tail; 970 if (part1_len) { 971 sg = &sgl[sg_len++]; 972 sg_dma_address(sg) = phys_addr; 973 sg_dma_len(sg) = part1_len; 974 975 phys_addr += part1_len; 976 } 977 978 if (part2_len) { 979 sg = &sgl[sg_len++]; 980 sg_dma_address(sg) = phys_addr; 981 sg_dma_len(sg) = part2_len; 982 } 983 984 /* 985 * save tx_len so atmel_complete_tx_dma() will increase 986 * xmit->tail correctly 987 */ 988 atmel_port->tx_len = tx_len; 989 990 desc = dmaengine_prep_slave_sg(chan, 991 sgl, 992 sg_len, 993 DMA_MEM_TO_DEV, 994 DMA_PREP_INTERRUPT | 995 DMA_CTRL_ACK); 996 if (!desc) { 997 dev_err(port->dev, "Failed to send via dma!\n"); 998 return; 999 } 1000 1001 dma_sync_sg_for_device(port->dev, sg_tx, 1, DMA_TO_DEVICE); 1002 1003 atmel_port->desc_tx = desc; 1004 desc->callback = atmel_complete_tx_dma; 1005 desc->callback_param = atmel_port; 1006 atmel_port->cookie_tx = dmaengine_submit(desc); 1007 } 1008 1009 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) 1010 uart_write_wakeup(port); 1011 } 1012 1013 static int atmel_prepare_tx_dma(struct uart_port *port) 1014 { 1015 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 1016 struct device *mfd_dev = port->dev->parent; 1017 dma_cap_mask_t mask; 1018 struct dma_slave_config config; 1019 int ret, nent; 1020 1021 dma_cap_zero(mask); 1022 dma_cap_set(DMA_SLAVE, mask); 1023 1024 atmel_port->chan_tx = dma_request_slave_channel(mfd_dev, "tx"); 1025 if (atmel_port->chan_tx == NULL) 1026 goto chan_err; 1027 dev_info(port->dev, "using %s for tx DMA transfers\n", 1028 dma_chan_name(atmel_port->chan_tx)); 1029 1030 spin_lock_init(&atmel_port->lock_tx); 1031 sg_init_table(&atmel_port->sg_tx, 1); 1032 /* UART circular tx buffer is an aligned page. */ 1033 BUG_ON(!PAGE_ALIGNED(port->state->xmit.buf)); 1034 sg_set_page(&atmel_port->sg_tx, 1035 virt_to_page(port->state->xmit.buf), 1036 UART_XMIT_SIZE, 1037 offset_in_page(port->state->xmit.buf)); 1038 nent = dma_map_sg(port->dev, 1039 &atmel_port->sg_tx, 1040 1, 1041 DMA_TO_DEVICE); 1042 1043 if (!nent) { 1044 dev_dbg(port->dev, "need to release resource of dma\n"); 1045 goto chan_err; 1046 } else { 1047 dev_dbg(port->dev, "%s: mapped %d@%p to %pad\n", __func__, 1048 sg_dma_len(&atmel_port->sg_tx), 1049 port->state->xmit.buf, 1050 &sg_dma_address(&atmel_port->sg_tx)); 1051 } 1052 1053 /* Configure the slave DMA */ 1054 memset(&config, 0, sizeof(config)); 1055 config.direction = DMA_MEM_TO_DEV; 1056 config.dst_addr_width = (atmel_port->fifo_size) ? 1057 DMA_SLAVE_BUSWIDTH_4_BYTES : 1058 DMA_SLAVE_BUSWIDTH_1_BYTE; 1059 config.dst_addr = port->mapbase + ATMEL_US_THR; 1060 config.dst_maxburst = 1; 1061 1062 ret = dmaengine_slave_config(atmel_port->chan_tx, 1063 &config); 1064 if (ret) { 1065 dev_err(port->dev, "DMA tx slave configuration failed\n"); 1066 goto chan_err; 1067 } 1068 1069 return 0; 1070 1071 chan_err: 1072 dev_err(port->dev, "TX channel not available, switch to pio\n"); 1073 atmel_port->use_dma_tx = false; 1074 if (atmel_port->chan_tx) 1075 atmel_release_tx_dma(port); 1076 return -EINVAL; 1077 } 1078 1079 static void atmel_complete_rx_dma(void *arg) 1080 { 1081 struct uart_port *port = arg; 1082 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 1083 1084 atmel_tasklet_schedule(atmel_port, &atmel_port->tasklet_rx); 1085 } 1086 1087 static void atmel_release_rx_dma(struct uart_port *port) 1088 { 1089 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 1090 struct dma_chan *chan = atmel_port->chan_rx; 1091 1092 if (chan) { 1093 dmaengine_terminate_all(chan); 1094 dma_release_channel(chan); 1095 dma_unmap_sg(port->dev, &atmel_port->sg_rx, 1, 1096 DMA_FROM_DEVICE); 1097 } 1098 1099 atmel_port->desc_rx = NULL; 1100 atmel_port->chan_rx = NULL; 1101 atmel_port->cookie_rx = -EINVAL; 1102 } 1103 1104 static void atmel_rx_from_dma(struct uart_port *port) 1105 { 1106 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 1107 struct tty_port *tport = &port->state->port; 1108 struct circ_buf *ring = &atmel_port->rx_ring; 1109 struct dma_chan *chan = atmel_port->chan_rx; 1110 struct dma_tx_state state; 1111 enum dma_status dmastat; 1112 size_t count; 1113 1114 1115 /* Reset the UART timeout early so that we don't miss one */ 1116 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_STTTO); 1117 dmastat = dmaengine_tx_status(chan, 1118 atmel_port->cookie_rx, 1119 &state); 1120 /* Restart a new tasklet if DMA status is error */ 1121 if (dmastat == DMA_ERROR) { 1122 dev_dbg(port->dev, "Get residue error, restart tasklet\n"); 1123 atmel_uart_writel(port, ATMEL_US_IER, ATMEL_US_TIMEOUT); 1124 atmel_tasklet_schedule(atmel_port, &atmel_port->tasklet_rx); 1125 return; 1126 } 1127 1128 /* CPU claims ownership of RX DMA buffer */ 1129 dma_sync_sg_for_cpu(port->dev, 1130 &atmel_port->sg_rx, 1131 1, 1132 DMA_FROM_DEVICE); 1133 1134 /* 1135 * ring->head points to the end of data already written by the DMA. 1136 * ring->tail points to the beginning of data to be read by the 1137 * framework. 1138 * The current transfer size should not be larger than the dma buffer 1139 * length. 1140 */ 1141 ring->head = sg_dma_len(&atmel_port->sg_rx) - state.residue; 1142 BUG_ON(ring->head > sg_dma_len(&atmel_port->sg_rx)); 1143 /* 1144 * At this point ring->head may point to the first byte right after the 1145 * last byte of the dma buffer: 1146 * 0 <= ring->head <= sg_dma_len(&atmel_port->sg_rx) 1147 * 1148 * However ring->tail must always points inside the dma buffer: 1149 * 0 <= ring->tail <= sg_dma_len(&atmel_port->sg_rx) - 1 1150 * 1151 * Since we use a ring buffer, we have to handle the case 1152 * where head is lower than tail. In such a case, we first read from 1153 * tail to the end of the buffer then reset tail. 1154 */ 1155 if (ring->head < ring->tail) { 1156 count = sg_dma_len(&atmel_port->sg_rx) - ring->tail; 1157 1158 tty_insert_flip_string(tport, ring->buf + ring->tail, count); 1159 ring->tail = 0; 1160 port->icount.rx += count; 1161 } 1162 1163 /* Finally we read data from tail to head */ 1164 if (ring->tail < ring->head) { 1165 count = ring->head - ring->tail; 1166 1167 tty_insert_flip_string(tport, ring->buf + ring->tail, count); 1168 /* Wrap ring->head if needed */ 1169 if (ring->head >= sg_dma_len(&atmel_port->sg_rx)) 1170 ring->head = 0; 1171 ring->tail = ring->head; 1172 port->icount.rx += count; 1173 } 1174 1175 /* USART retreives ownership of RX DMA buffer */ 1176 dma_sync_sg_for_device(port->dev, 1177 &atmel_port->sg_rx, 1178 1, 1179 DMA_FROM_DEVICE); 1180 1181 tty_flip_buffer_push(tport); 1182 1183 atmel_uart_writel(port, ATMEL_US_IER, ATMEL_US_TIMEOUT); 1184 } 1185 1186 static int atmel_prepare_rx_dma(struct uart_port *port) 1187 { 1188 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 1189 struct device *mfd_dev = port->dev->parent; 1190 struct dma_async_tx_descriptor *desc; 1191 dma_cap_mask_t mask; 1192 struct dma_slave_config config; 1193 struct circ_buf *ring; 1194 int ret, nent; 1195 1196 ring = &atmel_port->rx_ring; 1197 1198 dma_cap_zero(mask); 1199 dma_cap_set(DMA_CYCLIC, mask); 1200 1201 atmel_port->chan_rx = dma_request_slave_channel(mfd_dev, "rx"); 1202 if (atmel_port->chan_rx == NULL) 1203 goto chan_err; 1204 dev_info(port->dev, "using %s for rx DMA transfers\n", 1205 dma_chan_name(atmel_port->chan_rx)); 1206 1207 spin_lock_init(&atmel_port->lock_rx); 1208 sg_init_table(&atmel_port->sg_rx, 1); 1209 /* UART circular rx buffer is an aligned page. */ 1210 BUG_ON(!PAGE_ALIGNED(ring->buf)); 1211 sg_set_page(&atmel_port->sg_rx, 1212 virt_to_page(ring->buf), 1213 sizeof(struct atmel_uart_char) * ATMEL_SERIAL_RINGSIZE, 1214 offset_in_page(ring->buf)); 1215 nent = dma_map_sg(port->dev, 1216 &atmel_port->sg_rx, 1217 1, 1218 DMA_FROM_DEVICE); 1219 1220 if (!nent) { 1221 dev_dbg(port->dev, "need to release resource of dma\n"); 1222 goto chan_err; 1223 } else { 1224 dev_dbg(port->dev, "%s: mapped %d@%p to %pad\n", __func__, 1225 sg_dma_len(&atmel_port->sg_rx), 1226 ring->buf, 1227 &sg_dma_address(&atmel_port->sg_rx)); 1228 } 1229 1230 /* Configure the slave DMA */ 1231 memset(&config, 0, sizeof(config)); 1232 config.direction = DMA_DEV_TO_MEM; 1233 config.src_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE; 1234 config.src_addr = port->mapbase + ATMEL_US_RHR; 1235 config.src_maxburst = 1; 1236 1237 ret = dmaengine_slave_config(atmel_port->chan_rx, 1238 &config); 1239 if (ret) { 1240 dev_err(port->dev, "DMA rx slave configuration failed\n"); 1241 goto chan_err; 1242 } 1243 /* 1244 * Prepare a cyclic dma transfer, assign 2 descriptors, 1245 * each one is half ring buffer size 1246 */ 1247 desc = dmaengine_prep_dma_cyclic(atmel_port->chan_rx, 1248 sg_dma_address(&atmel_port->sg_rx), 1249 sg_dma_len(&atmel_port->sg_rx), 1250 sg_dma_len(&atmel_port->sg_rx)/2, 1251 DMA_DEV_TO_MEM, 1252 DMA_PREP_INTERRUPT); 1253 if (!desc) { 1254 dev_err(port->dev, "Preparing DMA cyclic failed\n"); 1255 goto chan_err; 1256 } 1257 desc->callback = atmel_complete_rx_dma; 1258 desc->callback_param = port; 1259 atmel_port->desc_rx = desc; 1260 atmel_port->cookie_rx = dmaengine_submit(desc); 1261 1262 return 0; 1263 1264 chan_err: 1265 dev_err(port->dev, "RX channel not available, switch to pio\n"); 1266 atmel_port->use_dma_rx = false; 1267 if (atmel_port->chan_rx) 1268 atmel_release_rx_dma(port); 1269 return -EINVAL; 1270 } 1271 1272 static void atmel_uart_timer_callback(struct timer_list *t) 1273 { 1274 struct atmel_uart_port *atmel_port = from_timer(atmel_port, t, 1275 uart_timer); 1276 struct uart_port *port = &atmel_port->uart; 1277 1278 if (!atomic_read(&atmel_port->tasklet_shutdown)) { 1279 tasklet_schedule(&atmel_port->tasklet_rx); 1280 mod_timer(&atmel_port->uart_timer, 1281 jiffies + uart_poll_timeout(port)); 1282 } 1283 } 1284 1285 /* 1286 * receive interrupt handler. 1287 */ 1288 static void 1289 atmel_handle_receive(struct uart_port *port, unsigned int pending) 1290 { 1291 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 1292 1293 if (atmel_use_pdc_rx(port)) { 1294 /* 1295 * PDC receive. Just schedule the tasklet and let it 1296 * figure out the details. 1297 * 1298 * TODO: We're not handling error flags correctly at 1299 * the moment. 1300 */ 1301 if (pending & (ATMEL_US_ENDRX | ATMEL_US_TIMEOUT)) { 1302 atmel_uart_writel(port, ATMEL_US_IDR, 1303 (ATMEL_US_ENDRX | ATMEL_US_TIMEOUT)); 1304 atmel_tasklet_schedule(atmel_port, 1305 &atmel_port->tasklet_rx); 1306 } 1307 1308 if (pending & (ATMEL_US_RXBRK | ATMEL_US_OVRE | 1309 ATMEL_US_FRAME | ATMEL_US_PARE)) 1310 atmel_pdc_rxerr(port, pending); 1311 } 1312 1313 if (atmel_use_dma_rx(port)) { 1314 if (pending & ATMEL_US_TIMEOUT) { 1315 atmel_uart_writel(port, ATMEL_US_IDR, 1316 ATMEL_US_TIMEOUT); 1317 atmel_tasklet_schedule(atmel_port, 1318 &atmel_port->tasklet_rx); 1319 } 1320 } 1321 1322 /* Interrupt receive */ 1323 if (pending & ATMEL_US_RXRDY) 1324 atmel_rx_chars(port); 1325 else if (pending & ATMEL_US_RXBRK) { 1326 /* 1327 * End of break detected. If it came along with a 1328 * character, atmel_rx_chars will handle it. 1329 */ 1330 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA); 1331 atmel_uart_writel(port, ATMEL_US_IDR, ATMEL_US_RXBRK); 1332 atmel_port->break_active = 0; 1333 } 1334 } 1335 1336 /* 1337 * transmit interrupt handler. (Transmit is IRQF_NODELAY safe) 1338 */ 1339 static void 1340 atmel_handle_transmit(struct uart_port *port, unsigned int pending) 1341 { 1342 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 1343 1344 if (pending & atmel_port->tx_done_mask) { 1345 atmel_uart_writel(port, ATMEL_US_IDR, 1346 atmel_port->tx_done_mask); 1347 1348 /* Start RX if flag was set and FIFO is empty */ 1349 if (atmel_port->hd_start_rx) { 1350 if (!(atmel_uart_readl(port, ATMEL_US_CSR) 1351 & ATMEL_US_TXEMPTY)) 1352 dev_warn(port->dev, "Should start RX, but TX fifo is not empty\n"); 1353 1354 atmel_port->hd_start_rx = false; 1355 atmel_start_rx(port); 1356 } 1357 1358 atmel_tasklet_schedule(atmel_port, &atmel_port->tasklet_tx); 1359 } 1360 } 1361 1362 /* 1363 * status flags interrupt handler. 1364 */ 1365 static void 1366 atmel_handle_status(struct uart_port *port, unsigned int pending, 1367 unsigned int status) 1368 { 1369 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 1370 unsigned int status_change; 1371 1372 if (pending & (ATMEL_US_RIIC | ATMEL_US_DSRIC | ATMEL_US_DCDIC 1373 | ATMEL_US_CTSIC)) { 1374 status_change = status ^ atmel_port->irq_status_prev; 1375 atmel_port->irq_status_prev = status; 1376 1377 if (status_change & (ATMEL_US_RI | ATMEL_US_DSR 1378 | ATMEL_US_DCD | ATMEL_US_CTS)) { 1379 /* TODO: All reads to CSR will clear these interrupts! */ 1380 if (status_change & ATMEL_US_RI) 1381 port->icount.rng++; 1382 if (status_change & ATMEL_US_DSR) 1383 port->icount.dsr++; 1384 if (status_change & ATMEL_US_DCD) 1385 uart_handle_dcd_change(port, !(status & ATMEL_US_DCD)); 1386 if (status_change & ATMEL_US_CTS) 1387 uart_handle_cts_change(port, !(status & ATMEL_US_CTS)); 1388 1389 wake_up_interruptible(&port->state->port.delta_msr_wait); 1390 } 1391 } 1392 1393 if (pending & (ATMEL_US_NACK | ATMEL_US_ITERATION)) 1394 dev_dbg(port->dev, "ISO7816 ERROR (0x%08x)\n", pending); 1395 } 1396 1397 /* 1398 * Interrupt handler 1399 */ 1400 static irqreturn_t atmel_interrupt(int irq, void *dev_id) 1401 { 1402 struct uart_port *port = dev_id; 1403 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 1404 unsigned int status, pending, mask, pass_counter = 0; 1405 1406 spin_lock(&atmel_port->lock_suspended); 1407 1408 do { 1409 status = atmel_uart_readl(port, ATMEL_US_CSR); 1410 mask = atmel_uart_readl(port, ATMEL_US_IMR); 1411 pending = status & mask; 1412 if (!pending) 1413 break; 1414 1415 if (atmel_port->suspended) { 1416 atmel_port->pending |= pending; 1417 atmel_port->pending_status = status; 1418 atmel_uart_writel(port, ATMEL_US_IDR, mask); 1419 pm_system_wakeup(); 1420 break; 1421 } 1422 1423 atmel_handle_receive(port, pending); 1424 atmel_handle_status(port, pending, status); 1425 atmel_handle_transmit(port, pending); 1426 } while (pass_counter++ < ATMEL_ISR_PASS_LIMIT); 1427 1428 spin_unlock(&atmel_port->lock_suspended); 1429 1430 return pass_counter ? IRQ_HANDLED : IRQ_NONE; 1431 } 1432 1433 static void atmel_release_tx_pdc(struct uart_port *port) 1434 { 1435 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 1436 struct atmel_dma_buffer *pdc = &atmel_port->pdc_tx; 1437 1438 dma_unmap_single(port->dev, 1439 pdc->dma_addr, 1440 pdc->dma_size, 1441 DMA_TO_DEVICE); 1442 } 1443 1444 /* 1445 * Called from tasklet with ENDTX and TXBUFE interrupts disabled. 1446 */ 1447 static void atmel_tx_pdc(struct uart_port *port) 1448 { 1449 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 1450 struct circ_buf *xmit = &port->state->xmit; 1451 struct atmel_dma_buffer *pdc = &atmel_port->pdc_tx; 1452 int count; 1453 1454 /* nothing left to transmit? */ 1455 if (atmel_uart_readl(port, ATMEL_PDC_TCR)) 1456 return; 1457 1458 xmit->tail += pdc->ofs; 1459 xmit->tail &= UART_XMIT_SIZE - 1; 1460 1461 port->icount.tx += pdc->ofs; 1462 pdc->ofs = 0; 1463 1464 /* more to transmit - setup next transfer */ 1465 1466 /* disable PDC transmit */ 1467 atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_TXTDIS); 1468 1469 if (!uart_circ_empty(xmit) && !uart_tx_stopped(port)) { 1470 dma_sync_single_for_device(port->dev, 1471 pdc->dma_addr, 1472 pdc->dma_size, 1473 DMA_TO_DEVICE); 1474 1475 count = CIRC_CNT_TO_END(xmit->head, xmit->tail, UART_XMIT_SIZE); 1476 pdc->ofs = count; 1477 1478 atmel_uart_writel(port, ATMEL_PDC_TPR, 1479 pdc->dma_addr + xmit->tail); 1480 atmel_uart_writel(port, ATMEL_PDC_TCR, count); 1481 /* re-enable PDC transmit */ 1482 atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_TXTEN); 1483 /* Enable interrupts */ 1484 atmel_uart_writel(port, ATMEL_US_IER, 1485 atmel_port->tx_done_mask); 1486 } else { 1487 if (atmel_uart_is_half_duplex(port)) { 1488 /* DMA done, stop TX, start RX for RS485 */ 1489 atmel_start_rx(port); 1490 } 1491 } 1492 1493 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) 1494 uart_write_wakeup(port); 1495 } 1496 1497 static int atmel_prepare_tx_pdc(struct uart_port *port) 1498 { 1499 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 1500 struct atmel_dma_buffer *pdc = &atmel_port->pdc_tx; 1501 struct circ_buf *xmit = &port->state->xmit; 1502 1503 pdc->buf = xmit->buf; 1504 pdc->dma_addr = dma_map_single(port->dev, 1505 pdc->buf, 1506 UART_XMIT_SIZE, 1507 DMA_TO_DEVICE); 1508 pdc->dma_size = UART_XMIT_SIZE; 1509 pdc->ofs = 0; 1510 1511 return 0; 1512 } 1513 1514 static void atmel_rx_from_ring(struct uart_port *port) 1515 { 1516 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 1517 struct circ_buf *ring = &atmel_port->rx_ring; 1518 unsigned int flg; 1519 unsigned int status; 1520 1521 while (ring->head != ring->tail) { 1522 struct atmel_uart_char c; 1523 1524 /* Make sure c is loaded after head. */ 1525 smp_rmb(); 1526 1527 c = ((struct atmel_uart_char *)ring->buf)[ring->tail]; 1528 1529 ring->tail = (ring->tail + 1) & (ATMEL_SERIAL_RINGSIZE - 1); 1530 1531 port->icount.rx++; 1532 status = c.status; 1533 flg = TTY_NORMAL; 1534 1535 /* 1536 * note that the error handling code is 1537 * out of the main execution path 1538 */ 1539 if (unlikely(status & (ATMEL_US_PARE | ATMEL_US_FRAME 1540 | ATMEL_US_OVRE | ATMEL_US_RXBRK))) { 1541 if (status & ATMEL_US_RXBRK) { 1542 /* ignore side-effect */ 1543 status &= ~(ATMEL_US_PARE | ATMEL_US_FRAME); 1544 1545 port->icount.brk++; 1546 if (uart_handle_break(port)) 1547 continue; 1548 } 1549 if (status & ATMEL_US_PARE) 1550 port->icount.parity++; 1551 if (status & ATMEL_US_FRAME) 1552 port->icount.frame++; 1553 if (status & ATMEL_US_OVRE) 1554 port->icount.overrun++; 1555 1556 status &= port->read_status_mask; 1557 1558 if (status & ATMEL_US_RXBRK) 1559 flg = TTY_BREAK; 1560 else if (status & ATMEL_US_PARE) 1561 flg = TTY_PARITY; 1562 else if (status & ATMEL_US_FRAME) 1563 flg = TTY_FRAME; 1564 } 1565 1566 1567 if (uart_handle_sysrq_char(port, c.ch)) 1568 continue; 1569 1570 uart_insert_char(port, status, ATMEL_US_OVRE, c.ch, flg); 1571 } 1572 1573 tty_flip_buffer_push(&port->state->port); 1574 } 1575 1576 static void atmel_release_rx_pdc(struct uart_port *port) 1577 { 1578 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 1579 int i; 1580 1581 for (i = 0; i < 2; i++) { 1582 struct atmel_dma_buffer *pdc = &atmel_port->pdc_rx[i]; 1583 1584 dma_unmap_single(port->dev, 1585 pdc->dma_addr, 1586 pdc->dma_size, 1587 DMA_FROM_DEVICE); 1588 kfree(pdc->buf); 1589 } 1590 } 1591 1592 static void atmel_rx_from_pdc(struct uart_port *port) 1593 { 1594 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 1595 struct tty_port *tport = &port->state->port; 1596 struct atmel_dma_buffer *pdc; 1597 int rx_idx = atmel_port->pdc_rx_idx; 1598 unsigned int head; 1599 unsigned int tail; 1600 unsigned int count; 1601 1602 do { 1603 /* Reset the UART timeout early so that we don't miss one */ 1604 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_STTTO); 1605 1606 pdc = &atmel_port->pdc_rx[rx_idx]; 1607 head = atmel_uart_readl(port, ATMEL_PDC_RPR) - pdc->dma_addr; 1608 tail = pdc->ofs; 1609 1610 /* If the PDC has switched buffers, RPR won't contain 1611 * any address within the current buffer. Since head 1612 * is unsigned, we just need a one-way comparison to 1613 * find out. 1614 * 1615 * In this case, we just need to consume the entire 1616 * buffer and resubmit it for DMA. This will clear the 1617 * ENDRX bit as well, so that we can safely re-enable 1618 * all interrupts below. 1619 */ 1620 head = min(head, pdc->dma_size); 1621 1622 if (likely(head != tail)) { 1623 dma_sync_single_for_cpu(port->dev, pdc->dma_addr, 1624 pdc->dma_size, DMA_FROM_DEVICE); 1625 1626 /* 1627 * head will only wrap around when we recycle 1628 * the DMA buffer, and when that happens, we 1629 * explicitly set tail to 0. So head will 1630 * always be greater than tail. 1631 */ 1632 count = head - tail; 1633 1634 tty_insert_flip_string(tport, pdc->buf + pdc->ofs, 1635 count); 1636 1637 dma_sync_single_for_device(port->dev, pdc->dma_addr, 1638 pdc->dma_size, DMA_FROM_DEVICE); 1639 1640 port->icount.rx += count; 1641 pdc->ofs = head; 1642 } 1643 1644 /* 1645 * If the current buffer is full, we need to check if 1646 * the next one contains any additional data. 1647 */ 1648 if (head >= pdc->dma_size) { 1649 pdc->ofs = 0; 1650 atmel_uart_writel(port, ATMEL_PDC_RNPR, pdc->dma_addr); 1651 atmel_uart_writel(port, ATMEL_PDC_RNCR, pdc->dma_size); 1652 1653 rx_idx = !rx_idx; 1654 atmel_port->pdc_rx_idx = rx_idx; 1655 } 1656 } while (head >= pdc->dma_size); 1657 1658 tty_flip_buffer_push(tport); 1659 1660 atmel_uart_writel(port, ATMEL_US_IER, 1661 ATMEL_US_ENDRX | ATMEL_US_TIMEOUT); 1662 } 1663 1664 static int atmel_prepare_rx_pdc(struct uart_port *port) 1665 { 1666 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 1667 int i; 1668 1669 for (i = 0; i < 2; i++) { 1670 struct atmel_dma_buffer *pdc = &atmel_port->pdc_rx[i]; 1671 1672 pdc->buf = kmalloc(PDC_BUFFER_SIZE, GFP_KERNEL); 1673 if (pdc->buf == NULL) { 1674 if (i != 0) { 1675 dma_unmap_single(port->dev, 1676 atmel_port->pdc_rx[0].dma_addr, 1677 PDC_BUFFER_SIZE, 1678 DMA_FROM_DEVICE); 1679 kfree(atmel_port->pdc_rx[0].buf); 1680 } 1681 atmel_port->use_pdc_rx = false; 1682 return -ENOMEM; 1683 } 1684 pdc->dma_addr = dma_map_single(port->dev, 1685 pdc->buf, 1686 PDC_BUFFER_SIZE, 1687 DMA_FROM_DEVICE); 1688 pdc->dma_size = PDC_BUFFER_SIZE; 1689 pdc->ofs = 0; 1690 } 1691 1692 atmel_port->pdc_rx_idx = 0; 1693 1694 atmel_uart_writel(port, ATMEL_PDC_RPR, atmel_port->pdc_rx[0].dma_addr); 1695 atmel_uart_writel(port, ATMEL_PDC_RCR, PDC_BUFFER_SIZE); 1696 1697 atmel_uart_writel(port, ATMEL_PDC_RNPR, 1698 atmel_port->pdc_rx[1].dma_addr); 1699 atmel_uart_writel(port, ATMEL_PDC_RNCR, PDC_BUFFER_SIZE); 1700 1701 return 0; 1702 } 1703 1704 /* 1705 * tasklet handling tty stuff outside the interrupt handler. 1706 */ 1707 static void atmel_tasklet_rx_func(struct tasklet_struct *t) 1708 { 1709 struct atmel_uart_port *atmel_port = from_tasklet(atmel_port, t, 1710 tasklet_rx); 1711 struct uart_port *port = &atmel_port->uart; 1712 1713 /* The interrupt handler does not take the lock */ 1714 spin_lock(&port->lock); 1715 atmel_port->schedule_rx(port); 1716 spin_unlock(&port->lock); 1717 } 1718 1719 static void atmel_tasklet_tx_func(struct tasklet_struct *t) 1720 { 1721 struct atmel_uart_port *atmel_port = from_tasklet(atmel_port, t, 1722 tasklet_tx); 1723 struct uart_port *port = &atmel_port->uart; 1724 1725 /* The interrupt handler does not take the lock */ 1726 spin_lock(&port->lock); 1727 atmel_port->schedule_tx(port); 1728 spin_unlock(&port->lock); 1729 } 1730 1731 static void atmel_init_property(struct atmel_uart_port *atmel_port, 1732 struct platform_device *pdev) 1733 { 1734 struct device_node *np = pdev->dev.of_node; 1735 1736 /* DMA/PDC usage specification */ 1737 if (of_property_read_bool(np, "atmel,use-dma-rx")) { 1738 if (of_property_read_bool(np, "dmas")) { 1739 atmel_port->use_dma_rx = true; 1740 atmel_port->use_pdc_rx = false; 1741 } else { 1742 atmel_port->use_dma_rx = false; 1743 atmel_port->use_pdc_rx = true; 1744 } 1745 } else { 1746 atmel_port->use_dma_rx = false; 1747 atmel_port->use_pdc_rx = false; 1748 } 1749 1750 if (of_property_read_bool(np, "atmel,use-dma-tx")) { 1751 if (of_property_read_bool(np, "dmas")) { 1752 atmel_port->use_dma_tx = true; 1753 atmel_port->use_pdc_tx = false; 1754 } else { 1755 atmel_port->use_dma_tx = false; 1756 atmel_port->use_pdc_tx = true; 1757 } 1758 } else { 1759 atmel_port->use_dma_tx = false; 1760 atmel_port->use_pdc_tx = false; 1761 } 1762 } 1763 1764 static void atmel_set_ops(struct uart_port *port) 1765 { 1766 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 1767 1768 if (atmel_use_dma_rx(port)) { 1769 atmel_port->prepare_rx = &atmel_prepare_rx_dma; 1770 atmel_port->schedule_rx = &atmel_rx_from_dma; 1771 atmel_port->release_rx = &atmel_release_rx_dma; 1772 } else if (atmel_use_pdc_rx(port)) { 1773 atmel_port->prepare_rx = &atmel_prepare_rx_pdc; 1774 atmel_port->schedule_rx = &atmel_rx_from_pdc; 1775 atmel_port->release_rx = &atmel_release_rx_pdc; 1776 } else { 1777 atmel_port->prepare_rx = NULL; 1778 atmel_port->schedule_rx = &atmel_rx_from_ring; 1779 atmel_port->release_rx = NULL; 1780 } 1781 1782 if (atmel_use_dma_tx(port)) { 1783 atmel_port->prepare_tx = &atmel_prepare_tx_dma; 1784 atmel_port->schedule_tx = &atmel_tx_dma; 1785 atmel_port->release_tx = &atmel_release_tx_dma; 1786 } else if (atmel_use_pdc_tx(port)) { 1787 atmel_port->prepare_tx = &atmel_prepare_tx_pdc; 1788 atmel_port->schedule_tx = &atmel_tx_pdc; 1789 atmel_port->release_tx = &atmel_release_tx_pdc; 1790 } else { 1791 atmel_port->prepare_tx = NULL; 1792 atmel_port->schedule_tx = &atmel_tx_chars; 1793 atmel_port->release_tx = NULL; 1794 } 1795 } 1796 1797 /* 1798 * Get ip name usart or uart 1799 */ 1800 static void atmel_get_ip_name(struct uart_port *port) 1801 { 1802 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 1803 int name = atmel_uart_readl(port, ATMEL_US_NAME); 1804 u32 version; 1805 u32 usart, dbgu_uart, new_uart; 1806 /* ASCII decoding for IP version */ 1807 usart = 0x55534152; /* USAR(T) */ 1808 dbgu_uart = 0x44424755; /* DBGU */ 1809 new_uart = 0x55415254; /* UART */ 1810 1811 /* 1812 * Only USART devices from at91sam9260 SOC implement fractional 1813 * baudrate. It is available for all asynchronous modes, with the 1814 * following restriction: the sampling clock's duty cycle is not 1815 * constant. 1816 */ 1817 atmel_port->has_frac_baudrate = false; 1818 atmel_port->has_hw_timer = false; 1819 1820 if (name == new_uart) { 1821 dev_dbg(port->dev, "Uart with hw timer"); 1822 atmel_port->has_hw_timer = true; 1823 atmel_port->rtor = ATMEL_UA_RTOR; 1824 } else if (name == usart) { 1825 dev_dbg(port->dev, "Usart\n"); 1826 atmel_port->has_frac_baudrate = true; 1827 atmel_port->has_hw_timer = true; 1828 atmel_port->rtor = ATMEL_US_RTOR; 1829 version = atmel_uart_readl(port, ATMEL_US_VERSION); 1830 switch (version) { 1831 case 0x814: /* sama5d2 */ 1832 fallthrough; 1833 case 0x701: /* sama5d4 */ 1834 atmel_port->fidi_min = 3; 1835 atmel_port->fidi_max = 65535; 1836 break; 1837 case 0x502: /* sam9x5, sama5d3 */ 1838 atmel_port->fidi_min = 3; 1839 atmel_port->fidi_max = 2047; 1840 break; 1841 default: 1842 atmel_port->fidi_min = 1; 1843 atmel_port->fidi_max = 2047; 1844 } 1845 } else if (name == dbgu_uart) { 1846 dev_dbg(port->dev, "Dbgu or uart without hw timer\n"); 1847 } else { 1848 /* fallback for older SoCs: use version field */ 1849 version = atmel_uart_readl(port, ATMEL_US_VERSION); 1850 switch (version) { 1851 case 0x302: 1852 case 0x10213: 1853 case 0x10302: 1854 dev_dbg(port->dev, "This version is usart\n"); 1855 atmel_port->has_frac_baudrate = true; 1856 atmel_port->has_hw_timer = true; 1857 atmel_port->rtor = ATMEL_US_RTOR; 1858 break; 1859 case 0x203: 1860 case 0x10202: 1861 dev_dbg(port->dev, "This version is uart\n"); 1862 break; 1863 default: 1864 dev_err(port->dev, "Not supported ip name nor version, set to uart\n"); 1865 } 1866 } 1867 } 1868 1869 /* 1870 * Perform initialization and enable port for reception 1871 */ 1872 static int atmel_startup(struct uart_port *port) 1873 { 1874 struct platform_device *pdev = to_platform_device(port->dev); 1875 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 1876 int retval; 1877 1878 /* 1879 * Ensure that no interrupts are enabled otherwise when 1880 * request_irq() is called we could get stuck trying to 1881 * handle an unexpected interrupt 1882 */ 1883 atmel_uart_writel(port, ATMEL_US_IDR, -1); 1884 atmel_port->ms_irq_enabled = false; 1885 1886 /* 1887 * Allocate the IRQ 1888 */ 1889 retval = request_irq(port->irq, atmel_interrupt, 1890 IRQF_SHARED | IRQF_COND_SUSPEND, 1891 dev_name(&pdev->dev), port); 1892 if (retval) { 1893 dev_err(port->dev, "atmel_startup - Can't get irq\n"); 1894 return retval; 1895 } 1896 1897 atomic_set(&atmel_port->tasklet_shutdown, 0); 1898 tasklet_setup(&atmel_port->tasklet_rx, atmel_tasklet_rx_func); 1899 tasklet_setup(&atmel_port->tasklet_tx, atmel_tasklet_tx_func); 1900 1901 /* 1902 * Initialize DMA (if necessary) 1903 */ 1904 atmel_init_property(atmel_port, pdev); 1905 atmel_set_ops(port); 1906 1907 if (atmel_port->prepare_rx) { 1908 retval = atmel_port->prepare_rx(port); 1909 if (retval < 0) 1910 atmel_set_ops(port); 1911 } 1912 1913 if (atmel_port->prepare_tx) { 1914 retval = atmel_port->prepare_tx(port); 1915 if (retval < 0) 1916 atmel_set_ops(port); 1917 } 1918 1919 /* 1920 * Enable FIFO when available 1921 */ 1922 if (atmel_port->fifo_size) { 1923 unsigned int txrdym = ATMEL_US_ONE_DATA; 1924 unsigned int rxrdym = ATMEL_US_ONE_DATA; 1925 unsigned int fmr; 1926 1927 atmel_uart_writel(port, ATMEL_US_CR, 1928 ATMEL_US_FIFOEN | 1929 ATMEL_US_RXFCLR | 1930 ATMEL_US_TXFLCLR); 1931 1932 if (atmel_use_dma_tx(port)) 1933 txrdym = ATMEL_US_FOUR_DATA; 1934 1935 fmr = ATMEL_US_TXRDYM(txrdym) | ATMEL_US_RXRDYM(rxrdym); 1936 if (atmel_port->rts_high && 1937 atmel_port->rts_low) 1938 fmr |= ATMEL_US_FRTSC | 1939 ATMEL_US_RXFTHRES(atmel_port->rts_high) | 1940 ATMEL_US_RXFTHRES2(atmel_port->rts_low); 1941 1942 atmel_uart_writel(port, ATMEL_US_FMR, fmr); 1943 } 1944 1945 /* Save current CSR for comparison in atmel_tasklet_func() */ 1946 atmel_port->irq_status_prev = atmel_uart_readl(port, ATMEL_US_CSR); 1947 1948 /* 1949 * Finally, enable the serial port 1950 */ 1951 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA | ATMEL_US_RSTRX); 1952 /* enable xmit & rcvr */ 1953 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXEN | ATMEL_US_RXEN); 1954 atmel_port->tx_stopped = false; 1955 1956 timer_setup(&atmel_port->uart_timer, atmel_uart_timer_callback, 0); 1957 1958 if (atmel_use_pdc_rx(port)) { 1959 /* set UART timeout */ 1960 if (!atmel_port->has_hw_timer) { 1961 mod_timer(&atmel_port->uart_timer, 1962 jiffies + uart_poll_timeout(port)); 1963 /* set USART timeout */ 1964 } else { 1965 atmel_uart_writel(port, atmel_port->rtor, 1966 PDC_RX_TIMEOUT); 1967 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_STTTO); 1968 1969 atmel_uart_writel(port, ATMEL_US_IER, 1970 ATMEL_US_ENDRX | ATMEL_US_TIMEOUT); 1971 } 1972 /* enable PDC controller */ 1973 atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_RXTEN); 1974 } else if (atmel_use_dma_rx(port)) { 1975 /* set UART timeout */ 1976 if (!atmel_port->has_hw_timer) { 1977 mod_timer(&atmel_port->uart_timer, 1978 jiffies + uart_poll_timeout(port)); 1979 /* set USART timeout */ 1980 } else { 1981 atmel_uart_writel(port, atmel_port->rtor, 1982 PDC_RX_TIMEOUT); 1983 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_STTTO); 1984 1985 atmel_uart_writel(port, ATMEL_US_IER, 1986 ATMEL_US_TIMEOUT); 1987 } 1988 } else { 1989 /* enable receive only */ 1990 atmel_uart_writel(port, ATMEL_US_IER, ATMEL_US_RXRDY); 1991 } 1992 1993 return 0; 1994 } 1995 1996 /* 1997 * Flush any TX data submitted for DMA. Called when the TX circular 1998 * buffer is reset. 1999 */ 2000 static void atmel_flush_buffer(struct uart_port *port) 2001 { 2002 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 2003 2004 if (atmel_use_pdc_tx(port)) { 2005 atmel_uart_writel(port, ATMEL_PDC_TCR, 0); 2006 atmel_port->pdc_tx.ofs = 0; 2007 } 2008 /* 2009 * in uart_flush_buffer(), the xmit circular buffer has just 2010 * been cleared, so we have to reset tx_len accordingly. 2011 */ 2012 atmel_port->tx_len = 0; 2013 } 2014 2015 /* 2016 * Disable the port 2017 */ 2018 static void atmel_shutdown(struct uart_port *port) 2019 { 2020 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 2021 2022 /* Disable modem control lines interrupts */ 2023 atmel_disable_ms(port); 2024 2025 /* Disable interrupts at device level */ 2026 atmel_uart_writel(port, ATMEL_US_IDR, -1); 2027 2028 /* Prevent spurious interrupts from scheduling the tasklet */ 2029 atomic_inc(&atmel_port->tasklet_shutdown); 2030 2031 /* 2032 * Prevent any tasklets being scheduled during 2033 * cleanup 2034 */ 2035 del_timer_sync(&atmel_port->uart_timer); 2036 2037 /* Make sure that no interrupt is on the fly */ 2038 synchronize_irq(port->irq); 2039 2040 /* 2041 * Clear out any scheduled tasklets before 2042 * we destroy the buffers 2043 */ 2044 tasklet_kill(&atmel_port->tasklet_rx); 2045 tasklet_kill(&atmel_port->tasklet_tx); 2046 2047 /* 2048 * Ensure everything is stopped and 2049 * disable port and break condition. 2050 */ 2051 atmel_stop_rx(port); 2052 atmel_stop_tx(port); 2053 2054 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA); 2055 2056 /* 2057 * Shut-down the DMA. 2058 */ 2059 if (atmel_port->release_rx) 2060 atmel_port->release_rx(port); 2061 if (atmel_port->release_tx) 2062 atmel_port->release_tx(port); 2063 2064 /* 2065 * Reset ring buffer pointers 2066 */ 2067 atmel_port->rx_ring.head = 0; 2068 atmel_port->rx_ring.tail = 0; 2069 2070 /* 2071 * Free the interrupts 2072 */ 2073 free_irq(port->irq, port); 2074 2075 atmel_flush_buffer(port); 2076 } 2077 2078 /* 2079 * Power / Clock management. 2080 */ 2081 static void atmel_serial_pm(struct uart_port *port, unsigned int state, 2082 unsigned int oldstate) 2083 { 2084 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 2085 2086 switch (state) { 2087 case UART_PM_STATE_ON: 2088 /* 2089 * Enable the peripheral clock for this serial port. 2090 * This is called on uart_open() or a resume event. 2091 */ 2092 clk_prepare_enable(atmel_port->clk); 2093 2094 /* re-enable interrupts if we disabled some on suspend */ 2095 atmel_uart_writel(port, ATMEL_US_IER, atmel_port->backup_imr); 2096 break; 2097 case UART_PM_STATE_OFF: 2098 /* Back up the interrupt mask and disable all interrupts */ 2099 atmel_port->backup_imr = atmel_uart_readl(port, ATMEL_US_IMR); 2100 atmel_uart_writel(port, ATMEL_US_IDR, -1); 2101 2102 /* 2103 * Disable the peripheral clock for this serial port. 2104 * This is called on uart_close() or a suspend event. 2105 */ 2106 clk_disable_unprepare(atmel_port->clk); 2107 break; 2108 default: 2109 dev_err(port->dev, "atmel_serial: unknown pm %d\n", state); 2110 } 2111 } 2112 2113 /* 2114 * Change the port parameters 2115 */ 2116 static void atmel_set_termios(struct uart_port *port, struct ktermios *termios, 2117 struct ktermios *old) 2118 { 2119 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 2120 unsigned long flags; 2121 unsigned int old_mode, mode, imr, quot, baud, div, cd, fp = 0; 2122 2123 /* save the current mode register */ 2124 mode = old_mode = atmel_uart_readl(port, ATMEL_US_MR); 2125 2126 /* reset the mode, clock divisor, parity, stop bits and data size */ 2127 mode &= ~(ATMEL_US_USCLKS | ATMEL_US_CHRL | ATMEL_US_NBSTOP | 2128 ATMEL_US_PAR | ATMEL_US_USMODE); 2129 2130 baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk / 16); 2131 2132 /* byte size */ 2133 switch (termios->c_cflag & CSIZE) { 2134 case CS5: 2135 mode |= ATMEL_US_CHRL_5; 2136 break; 2137 case CS6: 2138 mode |= ATMEL_US_CHRL_6; 2139 break; 2140 case CS7: 2141 mode |= ATMEL_US_CHRL_7; 2142 break; 2143 default: 2144 mode |= ATMEL_US_CHRL_8; 2145 break; 2146 } 2147 2148 /* stop bits */ 2149 if (termios->c_cflag & CSTOPB) 2150 mode |= ATMEL_US_NBSTOP_2; 2151 2152 /* parity */ 2153 if (termios->c_cflag & PARENB) { 2154 /* Mark or Space parity */ 2155 if (termios->c_cflag & CMSPAR) { 2156 if (termios->c_cflag & PARODD) 2157 mode |= ATMEL_US_PAR_MARK; 2158 else 2159 mode |= ATMEL_US_PAR_SPACE; 2160 } else if (termios->c_cflag & PARODD) 2161 mode |= ATMEL_US_PAR_ODD; 2162 else 2163 mode |= ATMEL_US_PAR_EVEN; 2164 } else 2165 mode |= ATMEL_US_PAR_NONE; 2166 2167 spin_lock_irqsave(&port->lock, flags); 2168 2169 port->read_status_mask = ATMEL_US_OVRE; 2170 if (termios->c_iflag & INPCK) 2171 port->read_status_mask |= (ATMEL_US_FRAME | ATMEL_US_PARE); 2172 if (termios->c_iflag & (IGNBRK | BRKINT | PARMRK)) 2173 port->read_status_mask |= ATMEL_US_RXBRK; 2174 2175 if (atmel_use_pdc_rx(port)) 2176 /* need to enable error interrupts */ 2177 atmel_uart_writel(port, ATMEL_US_IER, port->read_status_mask); 2178 2179 /* 2180 * Characters to ignore 2181 */ 2182 port->ignore_status_mask = 0; 2183 if (termios->c_iflag & IGNPAR) 2184 port->ignore_status_mask |= (ATMEL_US_FRAME | ATMEL_US_PARE); 2185 if (termios->c_iflag & IGNBRK) { 2186 port->ignore_status_mask |= ATMEL_US_RXBRK; 2187 /* 2188 * If we're ignoring parity and break indicators, 2189 * ignore overruns too (for real raw support). 2190 */ 2191 if (termios->c_iflag & IGNPAR) 2192 port->ignore_status_mask |= ATMEL_US_OVRE; 2193 } 2194 /* TODO: Ignore all characters if CREAD is set.*/ 2195 2196 /* update the per-port timeout */ 2197 uart_update_timeout(port, termios->c_cflag, baud); 2198 2199 /* 2200 * save/disable interrupts. The tty layer will ensure that the 2201 * transmitter is empty if requested by the caller, so there's 2202 * no need to wait for it here. 2203 */ 2204 imr = atmel_uart_readl(port, ATMEL_US_IMR); 2205 atmel_uart_writel(port, ATMEL_US_IDR, -1); 2206 2207 /* disable receiver and transmitter */ 2208 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXDIS | ATMEL_US_RXDIS); 2209 atmel_port->tx_stopped = true; 2210 2211 /* mode */ 2212 if (port->rs485.flags & SER_RS485_ENABLED) { 2213 atmel_uart_writel(port, ATMEL_US_TTGR, 2214 port->rs485.delay_rts_after_send); 2215 mode |= ATMEL_US_USMODE_RS485; 2216 } else if (port->iso7816.flags & SER_ISO7816_ENABLED) { 2217 atmel_uart_writel(port, ATMEL_US_TTGR, port->iso7816.tg); 2218 /* select mck clock, and output */ 2219 mode |= ATMEL_US_USCLKS_MCK | ATMEL_US_CLKO; 2220 /* set max iterations */ 2221 mode |= ATMEL_US_MAX_ITER(3); 2222 if ((port->iso7816.flags & SER_ISO7816_T_PARAM) 2223 == SER_ISO7816_T(0)) 2224 mode |= ATMEL_US_USMODE_ISO7816_T0; 2225 else 2226 mode |= ATMEL_US_USMODE_ISO7816_T1; 2227 } else if (termios->c_cflag & CRTSCTS) { 2228 /* RS232 with hardware handshake (RTS/CTS) */ 2229 if (atmel_use_fifo(port) && 2230 !mctrl_gpio_to_gpiod(atmel_port->gpios, UART_GPIO_CTS)) { 2231 /* 2232 * with ATMEL_US_USMODE_HWHS set, the controller will 2233 * be able to drive the RTS pin high/low when the RX 2234 * FIFO is above RXFTHRES/below RXFTHRES2. 2235 * It will also disable the transmitter when the CTS 2236 * pin is high. 2237 * This mode is not activated if CTS pin is a GPIO 2238 * because in this case, the transmitter is always 2239 * disabled (there must be an internal pull-up 2240 * responsible for this behaviour). 2241 * If the RTS pin is a GPIO, the controller won't be 2242 * able to drive it according to the FIFO thresholds, 2243 * but it will be handled by the driver. 2244 */ 2245 mode |= ATMEL_US_USMODE_HWHS; 2246 } else { 2247 /* 2248 * For platforms without FIFO, the flow control is 2249 * handled by the driver. 2250 */ 2251 mode |= ATMEL_US_USMODE_NORMAL; 2252 } 2253 } else { 2254 /* RS232 without hadware handshake */ 2255 mode |= ATMEL_US_USMODE_NORMAL; 2256 } 2257 2258 /* 2259 * Set the baud rate: 2260 * Fractional baudrate allows to setup output frequency more 2261 * accurately. This feature is enabled only when using normal mode. 2262 * baudrate = selected clock / (8 * (2 - OVER) * (CD + FP / 8)) 2263 * Currently, OVER is always set to 0 so we get 2264 * baudrate = selected clock / (16 * (CD + FP / 8)) 2265 * then 2266 * 8 CD + FP = selected clock / (2 * baudrate) 2267 */ 2268 if (atmel_port->has_frac_baudrate) { 2269 div = DIV_ROUND_CLOSEST(port->uartclk, baud * 2); 2270 cd = div >> 3; 2271 fp = div & ATMEL_US_FP_MASK; 2272 } else { 2273 cd = uart_get_divisor(port, baud); 2274 } 2275 2276 if (cd > 65535) { /* BRGR is 16-bit, so switch to slower clock */ 2277 cd /= 8; 2278 mode |= ATMEL_US_USCLKS_MCK_DIV8; 2279 } 2280 quot = cd | fp << ATMEL_US_FP_OFFSET; 2281 2282 if (!(port->iso7816.flags & SER_ISO7816_ENABLED)) 2283 atmel_uart_writel(port, ATMEL_US_BRGR, quot); 2284 2285 /* set the mode, clock divisor, parity, stop bits and data size */ 2286 atmel_uart_writel(port, ATMEL_US_MR, mode); 2287 2288 /* 2289 * when switching the mode, set the RTS line state according to the 2290 * new mode, otherwise keep the former state 2291 */ 2292 if ((old_mode & ATMEL_US_USMODE) != (mode & ATMEL_US_USMODE)) { 2293 unsigned int rts_state; 2294 2295 if ((mode & ATMEL_US_USMODE) == ATMEL_US_USMODE_HWHS) { 2296 /* let the hardware control the RTS line */ 2297 rts_state = ATMEL_US_RTSDIS; 2298 } else { 2299 /* force RTS line to low level */ 2300 rts_state = ATMEL_US_RTSEN; 2301 } 2302 2303 atmel_uart_writel(port, ATMEL_US_CR, rts_state); 2304 } 2305 2306 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA | ATMEL_US_RSTRX); 2307 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXEN | ATMEL_US_RXEN); 2308 atmel_port->tx_stopped = false; 2309 2310 /* restore interrupts */ 2311 atmel_uart_writel(port, ATMEL_US_IER, imr); 2312 2313 /* CTS flow-control and modem-status interrupts */ 2314 if (UART_ENABLE_MS(port, termios->c_cflag)) 2315 atmel_enable_ms(port); 2316 else 2317 atmel_disable_ms(port); 2318 2319 spin_unlock_irqrestore(&port->lock, flags); 2320 } 2321 2322 static void atmel_set_ldisc(struct uart_port *port, struct ktermios *termios) 2323 { 2324 if (termios->c_line == N_PPS) { 2325 port->flags |= UPF_HARDPPS_CD; 2326 spin_lock_irq(&port->lock); 2327 atmel_enable_ms(port); 2328 spin_unlock_irq(&port->lock); 2329 } else { 2330 port->flags &= ~UPF_HARDPPS_CD; 2331 if (!UART_ENABLE_MS(port, termios->c_cflag)) { 2332 spin_lock_irq(&port->lock); 2333 atmel_disable_ms(port); 2334 spin_unlock_irq(&port->lock); 2335 } 2336 } 2337 } 2338 2339 /* 2340 * Return string describing the specified port 2341 */ 2342 static const char *atmel_type(struct uart_port *port) 2343 { 2344 return (port->type == PORT_ATMEL) ? "ATMEL_SERIAL" : NULL; 2345 } 2346 2347 /* 2348 * Release the memory region(s) being used by 'port'. 2349 */ 2350 static void atmel_release_port(struct uart_port *port) 2351 { 2352 struct platform_device *mpdev = to_platform_device(port->dev->parent); 2353 int size = resource_size(mpdev->resource); 2354 2355 release_mem_region(port->mapbase, size); 2356 2357 if (port->flags & UPF_IOREMAP) { 2358 iounmap(port->membase); 2359 port->membase = NULL; 2360 } 2361 } 2362 2363 /* 2364 * Request the memory region(s) being used by 'port'. 2365 */ 2366 static int atmel_request_port(struct uart_port *port) 2367 { 2368 struct platform_device *mpdev = to_platform_device(port->dev->parent); 2369 int size = resource_size(mpdev->resource); 2370 2371 if (!request_mem_region(port->mapbase, size, "atmel_serial")) 2372 return -EBUSY; 2373 2374 if (port->flags & UPF_IOREMAP) { 2375 port->membase = ioremap(port->mapbase, size); 2376 if (port->membase == NULL) { 2377 release_mem_region(port->mapbase, size); 2378 return -ENOMEM; 2379 } 2380 } 2381 2382 return 0; 2383 } 2384 2385 /* 2386 * Configure/autoconfigure the port. 2387 */ 2388 static void atmel_config_port(struct uart_port *port, int flags) 2389 { 2390 if (flags & UART_CONFIG_TYPE) { 2391 port->type = PORT_ATMEL; 2392 atmel_request_port(port); 2393 } 2394 } 2395 2396 /* 2397 * Verify the new serial_struct (for TIOCSSERIAL). 2398 */ 2399 static int atmel_verify_port(struct uart_port *port, struct serial_struct *ser) 2400 { 2401 int ret = 0; 2402 if (ser->type != PORT_UNKNOWN && ser->type != PORT_ATMEL) 2403 ret = -EINVAL; 2404 if (port->irq != ser->irq) 2405 ret = -EINVAL; 2406 if (ser->io_type != SERIAL_IO_MEM) 2407 ret = -EINVAL; 2408 if (port->uartclk / 16 != ser->baud_base) 2409 ret = -EINVAL; 2410 if (port->mapbase != (unsigned long)ser->iomem_base) 2411 ret = -EINVAL; 2412 if (port->iobase != ser->port) 2413 ret = -EINVAL; 2414 if (ser->hub6 != 0) 2415 ret = -EINVAL; 2416 return ret; 2417 } 2418 2419 #ifdef CONFIG_CONSOLE_POLL 2420 static int atmel_poll_get_char(struct uart_port *port) 2421 { 2422 while (!(atmel_uart_readl(port, ATMEL_US_CSR) & ATMEL_US_RXRDY)) 2423 cpu_relax(); 2424 2425 return atmel_uart_read_char(port); 2426 } 2427 2428 static void atmel_poll_put_char(struct uart_port *port, unsigned char ch) 2429 { 2430 while (!(atmel_uart_readl(port, ATMEL_US_CSR) & ATMEL_US_TXRDY)) 2431 cpu_relax(); 2432 2433 atmel_uart_write_char(port, ch); 2434 } 2435 #endif 2436 2437 static const struct uart_ops atmel_pops = { 2438 .tx_empty = atmel_tx_empty, 2439 .set_mctrl = atmel_set_mctrl, 2440 .get_mctrl = atmel_get_mctrl, 2441 .stop_tx = atmel_stop_tx, 2442 .start_tx = atmel_start_tx, 2443 .stop_rx = atmel_stop_rx, 2444 .enable_ms = atmel_enable_ms, 2445 .break_ctl = atmel_break_ctl, 2446 .startup = atmel_startup, 2447 .shutdown = atmel_shutdown, 2448 .flush_buffer = atmel_flush_buffer, 2449 .set_termios = atmel_set_termios, 2450 .set_ldisc = atmel_set_ldisc, 2451 .type = atmel_type, 2452 .release_port = atmel_release_port, 2453 .request_port = atmel_request_port, 2454 .config_port = atmel_config_port, 2455 .verify_port = atmel_verify_port, 2456 .pm = atmel_serial_pm, 2457 #ifdef CONFIG_CONSOLE_POLL 2458 .poll_get_char = atmel_poll_get_char, 2459 .poll_put_char = atmel_poll_put_char, 2460 #endif 2461 }; 2462 2463 /* 2464 * Configure the port from the platform device resource info. 2465 */ 2466 static int atmel_init_port(struct atmel_uart_port *atmel_port, 2467 struct platform_device *pdev) 2468 { 2469 int ret; 2470 struct uart_port *port = &atmel_port->uart; 2471 struct platform_device *mpdev = to_platform_device(pdev->dev.parent); 2472 2473 atmel_init_property(atmel_port, pdev); 2474 atmel_set_ops(port); 2475 2476 port->iotype = UPIO_MEM; 2477 port->flags = UPF_BOOT_AUTOCONF | UPF_IOREMAP; 2478 port->ops = &atmel_pops; 2479 port->fifosize = 1; 2480 port->dev = &pdev->dev; 2481 port->mapbase = mpdev->resource[0].start; 2482 port->irq = mpdev->resource[1].start; 2483 port->rs485_config = atmel_config_rs485; 2484 port->iso7816_config = atmel_config_iso7816; 2485 port->membase = NULL; 2486 2487 memset(&atmel_port->rx_ring, 0, sizeof(atmel_port->rx_ring)); 2488 2489 ret = uart_get_rs485_mode(port); 2490 if (ret) 2491 return ret; 2492 2493 /* for console, the clock could already be configured */ 2494 if (!atmel_port->clk) { 2495 atmel_port->clk = clk_get(&mpdev->dev, "usart"); 2496 if (IS_ERR(atmel_port->clk)) { 2497 ret = PTR_ERR(atmel_port->clk); 2498 atmel_port->clk = NULL; 2499 return ret; 2500 } 2501 ret = clk_prepare_enable(atmel_port->clk); 2502 if (ret) { 2503 clk_put(atmel_port->clk); 2504 atmel_port->clk = NULL; 2505 return ret; 2506 } 2507 port->uartclk = clk_get_rate(atmel_port->clk); 2508 clk_disable_unprepare(atmel_port->clk); 2509 /* only enable clock when USART is in use */ 2510 } 2511 2512 /* 2513 * Use TXEMPTY for interrupt when rs485 or ISO7816 else TXRDY or 2514 * ENDTX|TXBUFE 2515 */ 2516 if (atmel_uart_is_half_duplex(port)) 2517 atmel_port->tx_done_mask = ATMEL_US_TXEMPTY; 2518 else if (atmel_use_pdc_tx(port)) { 2519 port->fifosize = PDC_BUFFER_SIZE; 2520 atmel_port->tx_done_mask = ATMEL_US_ENDTX | ATMEL_US_TXBUFE; 2521 } else { 2522 atmel_port->tx_done_mask = ATMEL_US_TXRDY; 2523 } 2524 2525 return 0; 2526 } 2527 2528 #ifdef CONFIG_SERIAL_ATMEL_CONSOLE 2529 static void atmel_console_putchar(struct uart_port *port, int ch) 2530 { 2531 while (!(atmel_uart_readl(port, ATMEL_US_CSR) & ATMEL_US_TXRDY)) 2532 cpu_relax(); 2533 atmel_uart_write_char(port, ch); 2534 } 2535 2536 /* 2537 * Interrupts are disabled on entering 2538 */ 2539 static void atmel_console_write(struct console *co, const char *s, u_int count) 2540 { 2541 struct uart_port *port = &atmel_ports[co->index].uart; 2542 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 2543 unsigned int status, imr; 2544 unsigned int pdc_tx; 2545 2546 /* 2547 * First, save IMR and then disable interrupts 2548 */ 2549 imr = atmel_uart_readl(port, ATMEL_US_IMR); 2550 atmel_uart_writel(port, ATMEL_US_IDR, 2551 ATMEL_US_RXRDY | atmel_port->tx_done_mask); 2552 2553 /* Store PDC transmit status and disable it */ 2554 pdc_tx = atmel_uart_readl(port, ATMEL_PDC_PTSR) & ATMEL_PDC_TXTEN; 2555 atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_TXTDIS); 2556 2557 /* Make sure that tx path is actually able to send characters */ 2558 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXEN); 2559 atmel_port->tx_stopped = false; 2560 2561 uart_console_write(port, s, count, atmel_console_putchar); 2562 2563 /* 2564 * Finally, wait for transmitter to become empty 2565 * and restore IMR 2566 */ 2567 do { 2568 status = atmel_uart_readl(port, ATMEL_US_CSR); 2569 } while (!(status & ATMEL_US_TXRDY)); 2570 2571 /* Restore PDC transmit status */ 2572 if (pdc_tx) 2573 atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_TXTEN); 2574 2575 /* set interrupts back the way they were */ 2576 atmel_uart_writel(port, ATMEL_US_IER, imr); 2577 } 2578 2579 /* 2580 * If the port was already initialised (eg, by a boot loader), 2581 * try to determine the current setup. 2582 */ 2583 static void __init atmel_console_get_options(struct uart_port *port, int *baud, 2584 int *parity, int *bits) 2585 { 2586 unsigned int mr, quot; 2587 2588 /* 2589 * If the baud rate generator isn't running, the port wasn't 2590 * initialized by the boot loader. 2591 */ 2592 quot = atmel_uart_readl(port, ATMEL_US_BRGR) & ATMEL_US_CD; 2593 if (!quot) 2594 return; 2595 2596 mr = atmel_uart_readl(port, ATMEL_US_MR) & ATMEL_US_CHRL; 2597 if (mr == ATMEL_US_CHRL_8) 2598 *bits = 8; 2599 else 2600 *bits = 7; 2601 2602 mr = atmel_uart_readl(port, ATMEL_US_MR) & ATMEL_US_PAR; 2603 if (mr == ATMEL_US_PAR_EVEN) 2604 *parity = 'e'; 2605 else if (mr == ATMEL_US_PAR_ODD) 2606 *parity = 'o'; 2607 2608 /* 2609 * The serial core only rounds down when matching this to a 2610 * supported baud rate. Make sure we don't end up slightly 2611 * lower than one of those, as it would make us fall through 2612 * to a much lower baud rate than we really want. 2613 */ 2614 *baud = port->uartclk / (16 * (quot - 1)); 2615 } 2616 2617 static int __init atmel_console_setup(struct console *co, char *options) 2618 { 2619 int ret; 2620 struct uart_port *port = &atmel_ports[co->index].uart; 2621 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 2622 int baud = 115200; 2623 int bits = 8; 2624 int parity = 'n'; 2625 int flow = 'n'; 2626 2627 if (port->membase == NULL) { 2628 /* Port not initialized yet - delay setup */ 2629 return -ENODEV; 2630 } 2631 2632 ret = clk_prepare_enable(atmel_ports[co->index].clk); 2633 if (ret) 2634 return ret; 2635 2636 atmel_uart_writel(port, ATMEL_US_IDR, -1); 2637 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA | ATMEL_US_RSTRX); 2638 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXEN | ATMEL_US_RXEN); 2639 atmel_port->tx_stopped = false; 2640 2641 if (options) 2642 uart_parse_options(options, &baud, &parity, &bits, &flow); 2643 else 2644 atmel_console_get_options(port, &baud, &parity, &bits); 2645 2646 return uart_set_options(port, co, baud, parity, bits, flow); 2647 } 2648 2649 static struct uart_driver atmel_uart; 2650 2651 static struct console atmel_console = { 2652 .name = ATMEL_DEVICENAME, 2653 .write = atmel_console_write, 2654 .device = uart_console_device, 2655 .setup = atmel_console_setup, 2656 .flags = CON_PRINTBUFFER, 2657 .index = -1, 2658 .data = &atmel_uart, 2659 }; 2660 2661 #define ATMEL_CONSOLE_DEVICE (&atmel_console) 2662 2663 #else 2664 #define ATMEL_CONSOLE_DEVICE NULL 2665 #endif 2666 2667 static struct uart_driver atmel_uart = { 2668 .owner = THIS_MODULE, 2669 .driver_name = "atmel_serial", 2670 .dev_name = ATMEL_DEVICENAME, 2671 .major = SERIAL_ATMEL_MAJOR, 2672 .minor = MINOR_START, 2673 .nr = ATMEL_MAX_UART, 2674 .cons = ATMEL_CONSOLE_DEVICE, 2675 }; 2676 2677 #ifdef CONFIG_PM 2678 static bool atmel_serial_clk_will_stop(void) 2679 { 2680 #ifdef CONFIG_ARCH_AT91 2681 return at91_suspend_entering_slow_clock(); 2682 #else 2683 return false; 2684 #endif 2685 } 2686 2687 static int atmel_serial_suspend(struct platform_device *pdev, 2688 pm_message_t state) 2689 { 2690 struct uart_port *port = platform_get_drvdata(pdev); 2691 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 2692 2693 if (uart_console(port) && console_suspend_enabled) { 2694 /* Drain the TX shifter */ 2695 while (!(atmel_uart_readl(port, ATMEL_US_CSR) & 2696 ATMEL_US_TXEMPTY)) 2697 cpu_relax(); 2698 } 2699 2700 if (uart_console(port) && !console_suspend_enabled) { 2701 /* Cache register values as we won't get a full shutdown/startup 2702 * cycle 2703 */ 2704 atmel_port->cache.mr = atmel_uart_readl(port, ATMEL_US_MR); 2705 atmel_port->cache.imr = atmel_uart_readl(port, ATMEL_US_IMR); 2706 atmel_port->cache.brgr = atmel_uart_readl(port, ATMEL_US_BRGR); 2707 atmel_port->cache.rtor = atmel_uart_readl(port, 2708 atmel_port->rtor); 2709 atmel_port->cache.ttgr = atmel_uart_readl(port, ATMEL_US_TTGR); 2710 atmel_port->cache.fmr = atmel_uart_readl(port, ATMEL_US_FMR); 2711 atmel_port->cache.fimr = atmel_uart_readl(port, ATMEL_US_FIMR); 2712 } 2713 2714 /* we can not wake up if we're running on slow clock */ 2715 atmel_port->may_wakeup = device_may_wakeup(&pdev->dev); 2716 if (atmel_serial_clk_will_stop()) { 2717 unsigned long flags; 2718 2719 spin_lock_irqsave(&atmel_port->lock_suspended, flags); 2720 atmel_port->suspended = true; 2721 spin_unlock_irqrestore(&atmel_port->lock_suspended, flags); 2722 device_set_wakeup_enable(&pdev->dev, 0); 2723 } 2724 2725 uart_suspend_port(&atmel_uart, port); 2726 2727 return 0; 2728 } 2729 2730 static int atmel_serial_resume(struct platform_device *pdev) 2731 { 2732 struct uart_port *port = platform_get_drvdata(pdev); 2733 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 2734 unsigned long flags; 2735 2736 if (uart_console(port) && !console_suspend_enabled) { 2737 atmel_uart_writel(port, ATMEL_US_MR, atmel_port->cache.mr); 2738 atmel_uart_writel(port, ATMEL_US_IER, atmel_port->cache.imr); 2739 atmel_uart_writel(port, ATMEL_US_BRGR, atmel_port->cache.brgr); 2740 atmel_uart_writel(port, atmel_port->rtor, 2741 atmel_port->cache.rtor); 2742 atmel_uart_writel(port, ATMEL_US_TTGR, atmel_port->cache.ttgr); 2743 2744 if (atmel_port->fifo_size) { 2745 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_FIFOEN | 2746 ATMEL_US_RXFCLR | ATMEL_US_TXFLCLR); 2747 atmel_uart_writel(port, ATMEL_US_FMR, 2748 atmel_port->cache.fmr); 2749 atmel_uart_writel(port, ATMEL_US_FIER, 2750 atmel_port->cache.fimr); 2751 } 2752 atmel_start_rx(port); 2753 } 2754 2755 spin_lock_irqsave(&atmel_port->lock_suspended, flags); 2756 if (atmel_port->pending) { 2757 atmel_handle_receive(port, atmel_port->pending); 2758 atmel_handle_status(port, atmel_port->pending, 2759 atmel_port->pending_status); 2760 atmel_handle_transmit(port, atmel_port->pending); 2761 atmel_port->pending = 0; 2762 } 2763 atmel_port->suspended = false; 2764 spin_unlock_irqrestore(&atmel_port->lock_suspended, flags); 2765 2766 uart_resume_port(&atmel_uart, port); 2767 device_set_wakeup_enable(&pdev->dev, atmel_port->may_wakeup); 2768 2769 return 0; 2770 } 2771 #else 2772 #define atmel_serial_suspend NULL 2773 #define atmel_serial_resume NULL 2774 #endif 2775 2776 static void atmel_serial_probe_fifos(struct atmel_uart_port *atmel_port, 2777 struct platform_device *pdev) 2778 { 2779 atmel_port->fifo_size = 0; 2780 atmel_port->rts_low = 0; 2781 atmel_port->rts_high = 0; 2782 2783 if (of_property_read_u32(pdev->dev.of_node, 2784 "atmel,fifo-size", 2785 &atmel_port->fifo_size)) 2786 return; 2787 2788 if (!atmel_port->fifo_size) 2789 return; 2790 2791 if (atmel_port->fifo_size < ATMEL_MIN_FIFO_SIZE) { 2792 atmel_port->fifo_size = 0; 2793 dev_err(&pdev->dev, "Invalid FIFO size\n"); 2794 return; 2795 } 2796 2797 /* 2798 * 0 <= rts_low <= rts_high <= fifo_size 2799 * Once their CTS line asserted by the remote peer, some x86 UARTs tend 2800 * to flush their internal TX FIFO, commonly up to 16 data, before 2801 * actually stopping to send new data. So we try to set the RTS High 2802 * Threshold to a reasonably high value respecting this 16 data 2803 * empirical rule when possible. 2804 */ 2805 atmel_port->rts_high = max_t(int, atmel_port->fifo_size >> 1, 2806 atmel_port->fifo_size - ATMEL_RTS_HIGH_OFFSET); 2807 atmel_port->rts_low = max_t(int, atmel_port->fifo_size >> 2, 2808 atmel_port->fifo_size - ATMEL_RTS_LOW_OFFSET); 2809 2810 dev_info(&pdev->dev, "Using FIFO (%u data)\n", 2811 atmel_port->fifo_size); 2812 dev_dbg(&pdev->dev, "RTS High Threshold : %2u data\n", 2813 atmel_port->rts_high); 2814 dev_dbg(&pdev->dev, "RTS Low Threshold : %2u data\n", 2815 atmel_port->rts_low); 2816 } 2817 2818 static int atmel_serial_probe(struct platform_device *pdev) 2819 { 2820 struct atmel_uart_port *atmel_port; 2821 struct device_node *np = pdev->dev.parent->of_node; 2822 void *data; 2823 int ret; 2824 bool rs485_enabled; 2825 2826 BUILD_BUG_ON(ATMEL_SERIAL_RINGSIZE & (ATMEL_SERIAL_RINGSIZE - 1)); 2827 2828 /* 2829 * In device tree there is no node with "atmel,at91rm9200-usart-serial" 2830 * as compatible string. This driver is probed by at91-usart mfd driver 2831 * which is just a wrapper over the atmel_serial driver and 2832 * spi-at91-usart driver. All attributes needed by this driver are 2833 * found in of_node of parent. 2834 */ 2835 pdev->dev.of_node = np; 2836 2837 ret = of_alias_get_id(np, "serial"); 2838 if (ret < 0) 2839 /* port id not found in platform data nor device-tree aliases: 2840 * auto-enumerate it */ 2841 ret = find_first_zero_bit(atmel_ports_in_use, ATMEL_MAX_UART); 2842 2843 if (ret >= ATMEL_MAX_UART) { 2844 ret = -ENODEV; 2845 goto err; 2846 } 2847 2848 if (test_and_set_bit(ret, atmel_ports_in_use)) { 2849 /* port already in use */ 2850 ret = -EBUSY; 2851 goto err; 2852 } 2853 2854 atmel_port = &atmel_ports[ret]; 2855 atmel_port->backup_imr = 0; 2856 atmel_port->uart.line = ret; 2857 atmel_port->uart.has_sysrq = IS_ENABLED(CONFIG_SERIAL_ATMEL_CONSOLE); 2858 atmel_serial_probe_fifos(atmel_port, pdev); 2859 2860 atomic_set(&atmel_port->tasklet_shutdown, 0); 2861 spin_lock_init(&atmel_port->lock_suspended); 2862 2863 ret = atmel_init_port(atmel_port, pdev); 2864 if (ret) 2865 goto err_clear_bit; 2866 2867 atmel_port->gpios = mctrl_gpio_init(&atmel_port->uart, 0); 2868 if (IS_ERR(atmel_port->gpios)) { 2869 ret = PTR_ERR(atmel_port->gpios); 2870 goto err_clear_bit; 2871 } 2872 2873 if (!atmel_use_pdc_rx(&atmel_port->uart)) { 2874 ret = -ENOMEM; 2875 data = kmalloc_array(ATMEL_SERIAL_RINGSIZE, 2876 sizeof(struct atmel_uart_char), 2877 GFP_KERNEL); 2878 if (!data) 2879 goto err_alloc_ring; 2880 atmel_port->rx_ring.buf = data; 2881 } 2882 2883 rs485_enabled = atmel_port->uart.rs485.flags & SER_RS485_ENABLED; 2884 2885 ret = uart_add_one_port(&atmel_uart, &atmel_port->uart); 2886 if (ret) 2887 goto err_add_port; 2888 2889 #ifdef CONFIG_SERIAL_ATMEL_CONSOLE 2890 if (uart_console(&atmel_port->uart) 2891 && ATMEL_CONSOLE_DEVICE->flags & CON_ENABLED) { 2892 /* 2893 * The serial core enabled the clock for us, so undo 2894 * the clk_prepare_enable() in atmel_console_setup() 2895 */ 2896 clk_disable_unprepare(atmel_port->clk); 2897 } 2898 #endif 2899 2900 device_init_wakeup(&pdev->dev, 1); 2901 platform_set_drvdata(pdev, atmel_port); 2902 2903 /* 2904 * The peripheral clock has been disabled by atmel_init_port(): 2905 * enable it before accessing I/O registers 2906 */ 2907 clk_prepare_enable(atmel_port->clk); 2908 2909 if (rs485_enabled) { 2910 atmel_uart_writel(&atmel_port->uart, ATMEL_US_MR, 2911 ATMEL_US_USMODE_NORMAL); 2912 atmel_uart_writel(&atmel_port->uart, ATMEL_US_CR, 2913 ATMEL_US_RTSEN); 2914 } 2915 2916 /* 2917 * Get port name of usart or uart 2918 */ 2919 atmel_get_ip_name(&atmel_port->uart); 2920 2921 /* 2922 * The peripheral clock can now safely be disabled till the port 2923 * is used 2924 */ 2925 clk_disable_unprepare(atmel_port->clk); 2926 2927 return 0; 2928 2929 err_add_port: 2930 kfree(atmel_port->rx_ring.buf); 2931 atmel_port->rx_ring.buf = NULL; 2932 err_alloc_ring: 2933 if (!uart_console(&atmel_port->uart)) { 2934 clk_put(atmel_port->clk); 2935 atmel_port->clk = NULL; 2936 } 2937 err_clear_bit: 2938 clear_bit(atmel_port->uart.line, atmel_ports_in_use); 2939 err: 2940 return ret; 2941 } 2942 2943 /* 2944 * Even if the driver is not modular, it makes sense to be able to 2945 * unbind a device: there can be many bound devices, and there are 2946 * situations where dynamic binding and unbinding can be useful. 2947 * 2948 * For example, a connected device can require a specific firmware update 2949 * protocol that needs bitbanging on IO lines, but use the regular serial 2950 * port in the normal case. 2951 */ 2952 static int atmel_serial_remove(struct platform_device *pdev) 2953 { 2954 struct uart_port *port = platform_get_drvdata(pdev); 2955 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 2956 int ret = 0; 2957 2958 tasklet_kill(&atmel_port->tasklet_rx); 2959 tasklet_kill(&atmel_port->tasklet_tx); 2960 2961 device_init_wakeup(&pdev->dev, 0); 2962 2963 ret = uart_remove_one_port(&atmel_uart, port); 2964 2965 kfree(atmel_port->rx_ring.buf); 2966 2967 /* "port" is allocated statically, so we shouldn't free it */ 2968 2969 clear_bit(port->line, atmel_ports_in_use); 2970 2971 clk_put(atmel_port->clk); 2972 atmel_port->clk = NULL; 2973 pdev->dev.of_node = NULL; 2974 2975 return ret; 2976 } 2977 2978 static struct platform_driver atmel_serial_driver = { 2979 .probe = atmel_serial_probe, 2980 .remove = atmel_serial_remove, 2981 .suspend = atmel_serial_suspend, 2982 .resume = atmel_serial_resume, 2983 .driver = { 2984 .name = "atmel_usart_serial", 2985 .of_match_table = of_match_ptr(atmel_serial_dt_ids), 2986 }, 2987 }; 2988 2989 static int __init atmel_serial_init(void) 2990 { 2991 int ret; 2992 2993 ret = uart_register_driver(&atmel_uart); 2994 if (ret) 2995 return ret; 2996 2997 ret = platform_driver_register(&atmel_serial_driver); 2998 if (ret) 2999 uart_unregister_driver(&atmel_uart); 3000 3001 return ret; 3002 } 3003 device_initcall(atmel_serial_init); 3004