1 /* 2 * Driver for AMBA serial ports 3 * 4 * Based on drivers/char/serial.c, by Linus Torvalds, Theodore Ts'o. 5 * 6 * Copyright 1999 ARM Limited 7 * Copyright (C) 2000 Deep Blue Solutions Ltd. 8 * Copyright (C) 2010 ST-Ericsson SA 9 * 10 * This program is free software; you can redistribute it and/or modify 11 * it under the terms of the GNU General Public License as published by 12 * the Free Software Foundation; either version 2 of the License, or 13 * (at your option) any later version. 14 * 15 * This program is distributed in the hope that it will be useful, 16 * but WITHOUT ANY WARRANTY; without even the implied warranty of 17 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the 18 * GNU General Public License for more details. 19 * 20 * You should have received a copy of the GNU General Public License 21 * along with this program; if not, write to the Free Software 22 * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA 23 * 24 * This is a generic driver for ARM AMBA-type serial ports. They 25 * have a lot of 16550-like features, but are not register compatible. 26 * Note that although they do have CTS, DCD and DSR inputs, they do 27 * not have an RI input, nor do they have DTR or RTS outputs. If 28 * required, these have to be supplied via some other means (eg, GPIO) 29 * and hooked into this driver. 30 */ 31 32 33 #if defined(CONFIG_SERIAL_AMBA_PL011_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ) 34 #define SUPPORT_SYSRQ 35 #endif 36 37 #include <linux/module.h> 38 #include <linux/ioport.h> 39 #include <linux/init.h> 40 #include <linux/console.h> 41 #include <linux/sysrq.h> 42 #include <linux/device.h> 43 #include <linux/tty.h> 44 #include <linux/tty_flip.h> 45 #include <linux/serial_core.h> 46 #include <linux/serial.h> 47 #include <linux/amba/bus.h> 48 #include <linux/amba/serial.h> 49 #include <linux/clk.h> 50 #include <linux/slab.h> 51 #include <linux/dmaengine.h> 52 #include <linux/dma-mapping.h> 53 #include <linux/scatterlist.h> 54 #include <linux/delay.h> 55 #include <linux/types.h> 56 #include <linux/of.h> 57 #include <linux/of_device.h> 58 #include <linux/pinctrl/consumer.h> 59 #include <linux/sizes.h> 60 #include <linux/io.h> 61 #include <linux/acpi.h> 62 63 #include "amba-pl011.h" 64 65 #define UART_NR 14 66 67 #define SERIAL_AMBA_MAJOR 204 68 #define SERIAL_AMBA_MINOR 64 69 #define SERIAL_AMBA_NR UART_NR 70 71 #define AMBA_ISR_PASS_LIMIT 256 72 73 #define UART_DR_ERROR (UART011_DR_OE|UART011_DR_BE|UART011_DR_PE|UART011_DR_FE) 74 #define UART_DUMMY_DR_RX (1 << 16) 75 76 static u16 pl011_std_offsets[REG_ARRAY_SIZE] = { 77 [REG_DR] = UART01x_DR, 78 [REG_FR] = UART01x_FR, 79 [REG_LCRH_RX] = UART011_LCRH, 80 [REG_LCRH_TX] = UART011_LCRH, 81 [REG_IBRD] = UART011_IBRD, 82 [REG_FBRD] = UART011_FBRD, 83 [REG_CR] = UART011_CR, 84 [REG_IFLS] = UART011_IFLS, 85 [REG_IMSC] = UART011_IMSC, 86 [REG_RIS] = UART011_RIS, 87 [REG_MIS] = UART011_MIS, 88 [REG_ICR] = UART011_ICR, 89 [REG_DMACR] = UART011_DMACR, 90 }; 91 92 /* There is by now at least one vendor with differing details, so handle it */ 93 struct vendor_data { 94 const u16 *reg_offset; 95 unsigned int ifls; 96 unsigned int fr_busy; 97 unsigned int fr_dsr; 98 unsigned int fr_cts; 99 unsigned int fr_ri; 100 unsigned int inv_fr; 101 bool access_32b; 102 bool oversampling; 103 bool dma_threshold; 104 bool cts_event_workaround; 105 bool always_enabled; 106 bool fixed_options; 107 108 unsigned int (*get_fifosize)(struct amba_device *dev); 109 }; 110 111 static unsigned int get_fifosize_arm(struct amba_device *dev) 112 { 113 return amba_rev(dev) < 3 ? 16 : 32; 114 } 115 116 static struct vendor_data vendor_arm = { 117 .reg_offset = pl011_std_offsets, 118 .ifls = UART011_IFLS_RX4_8|UART011_IFLS_TX4_8, 119 .fr_busy = UART01x_FR_BUSY, 120 .fr_dsr = UART01x_FR_DSR, 121 .fr_cts = UART01x_FR_CTS, 122 .fr_ri = UART011_FR_RI, 123 .oversampling = false, 124 .dma_threshold = false, 125 .cts_event_workaround = false, 126 .always_enabled = false, 127 .fixed_options = false, 128 .get_fifosize = get_fifosize_arm, 129 }; 130 131 static struct vendor_data vendor_sbsa = { 132 .reg_offset = pl011_std_offsets, 133 .fr_busy = UART01x_FR_BUSY, 134 .fr_dsr = UART01x_FR_DSR, 135 .fr_cts = UART01x_FR_CTS, 136 .fr_ri = UART011_FR_RI, 137 .access_32b = true, 138 .oversampling = false, 139 .dma_threshold = false, 140 .cts_event_workaround = false, 141 .always_enabled = true, 142 .fixed_options = true, 143 }; 144 145 /* 146 * Erratum 44 for QDF2432v1 and QDF2400v1 SoCs describes the BUSY bit as 147 * occasionally getting stuck as 1. To avoid the potential for a hang, check 148 * TXFE == 0 instead of BUSY == 1. This may not be suitable for all UART 149 * implementations, so only do so if an affected platform is detected in 150 * parse_spcr(). 151 */ 152 static bool qdf2400_e44_present = false; 153 154 static struct vendor_data vendor_qdt_qdf2400_e44 = { 155 .reg_offset = pl011_std_offsets, 156 .fr_busy = UART011_FR_TXFE, 157 .fr_dsr = UART01x_FR_DSR, 158 .fr_cts = UART01x_FR_CTS, 159 .fr_ri = UART011_FR_RI, 160 .inv_fr = UART011_FR_TXFE, 161 .access_32b = true, 162 .oversampling = false, 163 .dma_threshold = false, 164 .cts_event_workaround = false, 165 .always_enabled = true, 166 .fixed_options = true, 167 }; 168 169 static u16 pl011_st_offsets[REG_ARRAY_SIZE] = { 170 [REG_DR] = UART01x_DR, 171 [REG_ST_DMAWM] = ST_UART011_DMAWM, 172 [REG_ST_TIMEOUT] = ST_UART011_TIMEOUT, 173 [REG_FR] = UART01x_FR, 174 [REG_LCRH_RX] = ST_UART011_LCRH_RX, 175 [REG_LCRH_TX] = ST_UART011_LCRH_TX, 176 [REG_IBRD] = UART011_IBRD, 177 [REG_FBRD] = UART011_FBRD, 178 [REG_CR] = UART011_CR, 179 [REG_IFLS] = UART011_IFLS, 180 [REG_IMSC] = UART011_IMSC, 181 [REG_RIS] = UART011_RIS, 182 [REG_MIS] = UART011_MIS, 183 [REG_ICR] = UART011_ICR, 184 [REG_DMACR] = UART011_DMACR, 185 [REG_ST_XFCR] = ST_UART011_XFCR, 186 [REG_ST_XON1] = ST_UART011_XON1, 187 [REG_ST_XON2] = ST_UART011_XON2, 188 [REG_ST_XOFF1] = ST_UART011_XOFF1, 189 [REG_ST_XOFF2] = ST_UART011_XOFF2, 190 [REG_ST_ITCR] = ST_UART011_ITCR, 191 [REG_ST_ITIP] = ST_UART011_ITIP, 192 [REG_ST_ABCR] = ST_UART011_ABCR, 193 [REG_ST_ABIMSC] = ST_UART011_ABIMSC, 194 }; 195 196 static unsigned int get_fifosize_st(struct amba_device *dev) 197 { 198 return 64; 199 } 200 201 static struct vendor_data vendor_st = { 202 .reg_offset = pl011_st_offsets, 203 .ifls = UART011_IFLS_RX_HALF|UART011_IFLS_TX_HALF, 204 .fr_busy = UART01x_FR_BUSY, 205 .fr_dsr = UART01x_FR_DSR, 206 .fr_cts = UART01x_FR_CTS, 207 .fr_ri = UART011_FR_RI, 208 .oversampling = true, 209 .dma_threshold = true, 210 .cts_event_workaround = true, 211 .always_enabled = false, 212 .fixed_options = false, 213 .get_fifosize = get_fifosize_st, 214 }; 215 216 static const u16 pl011_zte_offsets[REG_ARRAY_SIZE] = { 217 [REG_DR] = ZX_UART011_DR, 218 [REG_FR] = ZX_UART011_FR, 219 [REG_LCRH_RX] = ZX_UART011_LCRH, 220 [REG_LCRH_TX] = ZX_UART011_LCRH, 221 [REG_IBRD] = ZX_UART011_IBRD, 222 [REG_FBRD] = ZX_UART011_FBRD, 223 [REG_CR] = ZX_UART011_CR, 224 [REG_IFLS] = ZX_UART011_IFLS, 225 [REG_IMSC] = ZX_UART011_IMSC, 226 [REG_RIS] = ZX_UART011_RIS, 227 [REG_MIS] = ZX_UART011_MIS, 228 [REG_ICR] = ZX_UART011_ICR, 229 [REG_DMACR] = ZX_UART011_DMACR, 230 }; 231 232 static unsigned int get_fifosize_zte(struct amba_device *dev) 233 { 234 return 16; 235 } 236 237 static struct vendor_data vendor_zte = { 238 .reg_offset = pl011_zte_offsets, 239 .access_32b = true, 240 .ifls = UART011_IFLS_RX4_8|UART011_IFLS_TX4_8, 241 .fr_busy = ZX_UART01x_FR_BUSY, 242 .fr_dsr = ZX_UART01x_FR_DSR, 243 .fr_cts = ZX_UART01x_FR_CTS, 244 .fr_ri = ZX_UART011_FR_RI, 245 .get_fifosize = get_fifosize_zte, 246 }; 247 248 /* Deals with DMA transactions */ 249 250 struct pl011_sgbuf { 251 struct scatterlist sg; 252 char *buf; 253 }; 254 255 struct pl011_dmarx_data { 256 struct dma_chan *chan; 257 struct completion complete; 258 bool use_buf_b; 259 struct pl011_sgbuf sgbuf_a; 260 struct pl011_sgbuf sgbuf_b; 261 dma_cookie_t cookie; 262 bool running; 263 struct timer_list timer; 264 unsigned int last_residue; 265 unsigned long last_jiffies; 266 bool auto_poll_rate; 267 unsigned int poll_rate; 268 unsigned int poll_timeout; 269 }; 270 271 struct pl011_dmatx_data { 272 struct dma_chan *chan; 273 struct scatterlist sg; 274 char *buf; 275 bool queued; 276 }; 277 278 /* 279 * We wrap our port structure around the generic uart_port. 280 */ 281 struct uart_amba_port { 282 struct uart_port port; 283 const u16 *reg_offset; 284 struct clk *clk; 285 const struct vendor_data *vendor; 286 unsigned int dmacr; /* dma control reg */ 287 unsigned int im; /* interrupt mask */ 288 unsigned int old_status; 289 unsigned int fifosize; /* vendor-specific */ 290 unsigned int old_cr; /* state during shutdown */ 291 bool autorts; 292 unsigned int fixed_baud; /* vendor-set fixed baud rate */ 293 char type[12]; 294 #ifdef CONFIG_DMA_ENGINE 295 /* DMA stuff */ 296 bool using_tx_dma; 297 bool using_rx_dma; 298 struct pl011_dmarx_data dmarx; 299 struct pl011_dmatx_data dmatx; 300 bool dma_probed; 301 #endif 302 }; 303 304 static unsigned int pl011_reg_to_offset(const struct uart_amba_port *uap, 305 unsigned int reg) 306 { 307 return uap->reg_offset[reg]; 308 } 309 310 static unsigned int pl011_read(const struct uart_amba_port *uap, 311 unsigned int reg) 312 { 313 void __iomem *addr = uap->port.membase + pl011_reg_to_offset(uap, reg); 314 315 return (uap->port.iotype == UPIO_MEM32) ? 316 readl_relaxed(addr) : readw_relaxed(addr); 317 } 318 319 static void pl011_write(unsigned int val, const struct uart_amba_port *uap, 320 unsigned int reg) 321 { 322 void __iomem *addr = uap->port.membase + pl011_reg_to_offset(uap, reg); 323 324 if (uap->port.iotype == UPIO_MEM32) 325 writel_relaxed(val, addr); 326 else 327 writew_relaxed(val, addr); 328 } 329 330 /* 331 * Reads up to 256 characters from the FIFO or until it's empty and 332 * inserts them into the TTY layer. Returns the number of characters 333 * read from the FIFO. 334 */ 335 static int pl011_fifo_to_tty(struct uart_amba_port *uap) 336 { 337 u16 status; 338 unsigned int ch, flag, max_count = 256; 339 int fifotaken = 0; 340 341 while (max_count--) { 342 status = pl011_read(uap, REG_FR); 343 if (status & UART01x_FR_RXFE) 344 break; 345 346 /* Take chars from the FIFO and update status */ 347 ch = pl011_read(uap, REG_DR) | UART_DUMMY_DR_RX; 348 flag = TTY_NORMAL; 349 uap->port.icount.rx++; 350 fifotaken++; 351 352 if (unlikely(ch & UART_DR_ERROR)) { 353 if (ch & UART011_DR_BE) { 354 ch &= ~(UART011_DR_FE | UART011_DR_PE); 355 uap->port.icount.brk++; 356 if (uart_handle_break(&uap->port)) 357 continue; 358 } else if (ch & UART011_DR_PE) 359 uap->port.icount.parity++; 360 else if (ch & UART011_DR_FE) 361 uap->port.icount.frame++; 362 if (ch & UART011_DR_OE) 363 uap->port.icount.overrun++; 364 365 ch &= uap->port.read_status_mask; 366 367 if (ch & UART011_DR_BE) 368 flag = TTY_BREAK; 369 else if (ch & UART011_DR_PE) 370 flag = TTY_PARITY; 371 else if (ch & UART011_DR_FE) 372 flag = TTY_FRAME; 373 } 374 375 if (uart_handle_sysrq_char(&uap->port, ch & 255)) 376 continue; 377 378 uart_insert_char(&uap->port, ch, UART011_DR_OE, ch, flag); 379 } 380 381 return fifotaken; 382 } 383 384 385 /* 386 * All the DMA operation mode stuff goes inside this ifdef. 387 * This assumes that you have a generic DMA device interface, 388 * no custom DMA interfaces are supported. 389 */ 390 #ifdef CONFIG_DMA_ENGINE 391 392 #define PL011_DMA_BUFFER_SIZE PAGE_SIZE 393 394 static int pl011_sgbuf_init(struct dma_chan *chan, struct pl011_sgbuf *sg, 395 enum dma_data_direction dir) 396 { 397 dma_addr_t dma_addr; 398 399 sg->buf = dma_alloc_coherent(chan->device->dev, 400 PL011_DMA_BUFFER_SIZE, &dma_addr, GFP_KERNEL); 401 if (!sg->buf) 402 return -ENOMEM; 403 404 sg_init_table(&sg->sg, 1); 405 sg_set_page(&sg->sg, phys_to_page(dma_addr), 406 PL011_DMA_BUFFER_SIZE, offset_in_page(dma_addr)); 407 sg_dma_address(&sg->sg) = dma_addr; 408 sg_dma_len(&sg->sg) = PL011_DMA_BUFFER_SIZE; 409 410 return 0; 411 } 412 413 static void pl011_sgbuf_free(struct dma_chan *chan, struct pl011_sgbuf *sg, 414 enum dma_data_direction dir) 415 { 416 if (sg->buf) { 417 dma_free_coherent(chan->device->dev, 418 PL011_DMA_BUFFER_SIZE, sg->buf, 419 sg_dma_address(&sg->sg)); 420 } 421 } 422 423 static void pl011_dma_probe(struct uart_amba_port *uap) 424 { 425 /* DMA is the sole user of the platform data right now */ 426 struct amba_pl011_data *plat = dev_get_platdata(uap->port.dev); 427 struct device *dev = uap->port.dev; 428 struct dma_slave_config tx_conf = { 429 .dst_addr = uap->port.mapbase + 430 pl011_reg_to_offset(uap, REG_DR), 431 .dst_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE, 432 .direction = DMA_MEM_TO_DEV, 433 .dst_maxburst = uap->fifosize >> 1, 434 .device_fc = false, 435 }; 436 struct dma_chan *chan; 437 dma_cap_mask_t mask; 438 439 uap->dma_probed = true; 440 chan = dma_request_slave_channel_reason(dev, "tx"); 441 if (IS_ERR(chan)) { 442 if (PTR_ERR(chan) == -EPROBE_DEFER) { 443 uap->dma_probed = false; 444 return; 445 } 446 447 /* We need platform data */ 448 if (!plat || !plat->dma_filter) { 449 dev_info(uap->port.dev, "no DMA platform data\n"); 450 return; 451 } 452 453 /* Try to acquire a generic DMA engine slave TX channel */ 454 dma_cap_zero(mask); 455 dma_cap_set(DMA_SLAVE, mask); 456 457 chan = dma_request_channel(mask, plat->dma_filter, 458 plat->dma_tx_param); 459 if (!chan) { 460 dev_err(uap->port.dev, "no TX DMA channel!\n"); 461 return; 462 } 463 } 464 465 dmaengine_slave_config(chan, &tx_conf); 466 uap->dmatx.chan = chan; 467 468 dev_info(uap->port.dev, "DMA channel TX %s\n", 469 dma_chan_name(uap->dmatx.chan)); 470 471 /* Optionally make use of an RX channel as well */ 472 chan = dma_request_slave_channel(dev, "rx"); 473 474 if (!chan && plat && plat->dma_rx_param) { 475 chan = dma_request_channel(mask, plat->dma_filter, plat->dma_rx_param); 476 477 if (!chan) { 478 dev_err(uap->port.dev, "no RX DMA channel!\n"); 479 return; 480 } 481 } 482 483 if (chan) { 484 struct dma_slave_config rx_conf = { 485 .src_addr = uap->port.mapbase + 486 pl011_reg_to_offset(uap, REG_DR), 487 .src_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE, 488 .direction = DMA_DEV_TO_MEM, 489 .src_maxburst = uap->fifosize >> 2, 490 .device_fc = false, 491 }; 492 struct dma_slave_caps caps; 493 494 /* 495 * Some DMA controllers provide information on their capabilities. 496 * If the controller does, check for suitable residue processing 497 * otherwise assime all is well. 498 */ 499 if (0 == dma_get_slave_caps(chan, &caps)) { 500 if (caps.residue_granularity == 501 DMA_RESIDUE_GRANULARITY_DESCRIPTOR) { 502 dma_release_channel(chan); 503 dev_info(uap->port.dev, 504 "RX DMA disabled - no residue processing\n"); 505 return; 506 } 507 } 508 dmaengine_slave_config(chan, &rx_conf); 509 uap->dmarx.chan = chan; 510 511 uap->dmarx.auto_poll_rate = false; 512 if (plat && plat->dma_rx_poll_enable) { 513 /* Set poll rate if specified. */ 514 if (plat->dma_rx_poll_rate) { 515 uap->dmarx.auto_poll_rate = false; 516 uap->dmarx.poll_rate = plat->dma_rx_poll_rate; 517 } else { 518 /* 519 * 100 ms defaults to poll rate if not 520 * specified. This will be adjusted with 521 * the baud rate at set_termios. 522 */ 523 uap->dmarx.auto_poll_rate = true; 524 uap->dmarx.poll_rate = 100; 525 } 526 /* 3 secs defaults poll_timeout if not specified. */ 527 if (plat->dma_rx_poll_timeout) 528 uap->dmarx.poll_timeout = 529 plat->dma_rx_poll_timeout; 530 else 531 uap->dmarx.poll_timeout = 3000; 532 } else if (!plat && dev->of_node) { 533 uap->dmarx.auto_poll_rate = of_property_read_bool( 534 dev->of_node, "auto-poll"); 535 if (uap->dmarx.auto_poll_rate) { 536 u32 x; 537 538 if (0 == of_property_read_u32(dev->of_node, 539 "poll-rate-ms", &x)) 540 uap->dmarx.poll_rate = x; 541 else 542 uap->dmarx.poll_rate = 100; 543 if (0 == of_property_read_u32(dev->of_node, 544 "poll-timeout-ms", &x)) 545 uap->dmarx.poll_timeout = x; 546 else 547 uap->dmarx.poll_timeout = 3000; 548 } 549 } 550 dev_info(uap->port.dev, "DMA channel RX %s\n", 551 dma_chan_name(uap->dmarx.chan)); 552 } 553 } 554 555 static void pl011_dma_remove(struct uart_amba_port *uap) 556 { 557 if (uap->dmatx.chan) 558 dma_release_channel(uap->dmatx.chan); 559 if (uap->dmarx.chan) 560 dma_release_channel(uap->dmarx.chan); 561 } 562 563 /* Forward declare these for the refill routine */ 564 static int pl011_dma_tx_refill(struct uart_amba_port *uap); 565 static void pl011_start_tx_pio(struct uart_amba_port *uap); 566 567 /* 568 * The current DMA TX buffer has been sent. 569 * Try to queue up another DMA buffer. 570 */ 571 static void pl011_dma_tx_callback(void *data) 572 { 573 struct uart_amba_port *uap = data; 574 struct pl011_dmatx_data *dmatx = &uap->dmatx; 575 unsigned long flags; 576 u16 dmacr; 577 578 spin_lock_irqsave(&uap->port.lock, flags); 579 if (uap->dmatx.queued) 580 dma_unmap_sg(dmatx->chan->device->dev, &dmatx->sg, 1, 581 DMA_TO_DEVICE); 582 583 dmacr = uap->dmacr; 584 uap->dmacr = dmacr & ~UART011_TXDMAE; 585 pl011_write(uap->dmacr, uap, REG_DMACR); 586 587 /* 588 * If TX DMA was disabled, it means that we've stopped the DMA for 589 * some reason (eg, XOFF received, or we want to send an X-char.) 590 * 591 * Note: we need to be careful here of a potential race between DMA 592 * and the rest of the driver - if the driver disables TX DMA while 593 * a TX buffer completing, we must update the tx queued status to 594 * get further refills (hence we check dmacr). 595 */ 596 if (!(dmacr & UART011_TXDMAE) || uart_tx_stopped(&uap->port) || 597 uart_circ_empty(&uap->port.state->xmit)) { 598 uap->dmatx.queued = false; 599 spin_unlock_irqrestore(&uap->port.lock, flags); 600 return; 601 } 602 603 if (pl011_dma_tx_refill(uap) <= 0) 604 /* 605 * We didn't queue a DMA buffer for some reason, but we 606 * have data pending to be sent. Re-enable the TX IRQ. 607 */ 608 pl011_start_tx_pio(uap); 609 610 spin_unlock_irqrestore(&uap->port.lock, flags); 611 } 612 613 /* 614 * Try to refill the TX DMA buffer. 615 * Locking: called with port lock held and IRQs disabled. 616 * Returns: 617 * 1 if we queued up a TX DMA buffer. 618 * 0 if we didn't want to handle this by DMA 619 * <0 on error 620 */ 621 static int pl011_dma_tx_refill(struct uart_amba_port *uap) 622 { 623 struct pl011_dmatx_data *dmatx = &uap->dmatx; 624 struct dma_chan *chan = dmatx->chan; 625 struct dma_device *dma_dev = chan->device; 626 struct dma_async_tx_descriptor *desc; 627 struct circ_buf *xmit = &uap->port.state->xmit; 628 unsigned int count; 629 630 /* 631 * Try to avoid the overhead involved in using DMA if the 632 * transaction fits in the first half of the FIFO, by using 633 * the standard interrupt handling. This ensures that we 634 * issue a uart_write_wakeup() at the appropriate time. 635 */ 636 count = uart_circ_chars_pending(xmit); 637 if (count < (uap->fifosize >> 1)) { 638 uap->dmatx.queued = false; 639 return 0; 640 } 641 642 /* 643 * Bodge: don't send the last character by DMA, as this 644 * will prevent XON from notifying us to restart DMA. 645 */ 646 count -= 1; 647 648 /* Else proceed to copy the TX chars to the DMA buffer and fire DMA */ 649 if (count > PL011_DMA_BUFFER_SIZE) 650 count = PL011_DMA_BUFFER_SIZE; 651 652 if (xmit->tail < xmit->head) 653 memcpy(&dmatx->buf[0], &xmit->buf[xmit->tail], count); 654 else { 655 size_t first = UART_XMIT_SIZE - xmit->tail; 656 size_t second; 657 658 if (first > count) 659 first = count; 660 second = count - first; 661 662 memcpy(&dmatx->buf[0], &xmit->buf[xmit->tail], first); 663 if (second) 664 memcpy(&dmatx->buf[first], &xmit->buf[0], second); 665 } 666 667 dmatx->sg.length = count; 668 669 if (dma_map_sg(dma_dev->dev, &dmatx->sg, 1, DMA_TO_DEVICE) != 1) { 670 uap->dmatx.queued = false; 671 dev_dbg(uap->port.dev, "unable to map TX DMA\n"); 672 return -EBUSY; 673 } 674 675 desc = dmaengine_prep_slave_sg(chan, &dmatx->sg, 1, DMA_MEM_TO_DEV, 676 DMA_PREP_INTERRUPT | DMA_CTRL_ACK); 677 if (!desc) { 678 dma_unmap_sg(dma_dev->dev, &dmatx->sg, 1, DMA_TO_DEVICE); 679 uap->dmatx.queued = false; 680 /* 681 * If DMA cannot be used right now, we complete this 682 * transaction via IRQ and let the TTY layer retry. 683 */ 684 dev_dbg(uap->port.dev, "TX DMA busy\n"); 685 return -EBUSY; 686 } 687 688 /* Some data to go along to the callback */ 689 desc->callback = pl011_dma_tx_callback; 690 desc->callback_param = uap; 691 692 /* All errors should happen at prepare time */ 693 dmaengine_submit(desc); 694 695 /* Fire the DMA transaction */ 696 dma_dev->device_issue_pending(chan); 697 698 uap->dmacr |= UART011_TXDMAE; 699 pl011_write(uap->dmacr, uap, REG_DMACR); 700 uap->dmatx.queued = true; 701 702 /* 703 * Now we know that DMA will fire, so advance the ring buffer 704 * with the stuff we just dispatched. 705 */ 706 xmit->tail = (xmit->tail + count) & (UART_XMIT_SIZE - 1); 707 uap->port.icount.tx += count; 708 709 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) 710 uart_write_wakeup(&uap->port); 711 712 return 1; 713 } 714 715 /* 716 * We received a transmit interrupt without a pending X-char but with 717 * pending characters. 718 * Locking: called with port lock held and IRQs disabled. 719 * Returns: 720 * false if we want to use PIO to transmit 721 * true if we queued a DMA buffer 722 */ 723 static bool pl011_dma_tx_irq(struct uart_amba_port *uap) 724 { 725 if (!uap->using_tx_dma) 726 return false; 727 728 /* 729 * If we already have a TX buffer queued, but received a 730 * TX interrupt, it will be because we've just sent an X-char. 731 * Ensure the TX DMA is enabled and the TX IRQ is disabled. 732 */ 733 if (uap->dmatx.queued) { 734 uap->dmacr |= UART011_TXDMAE; 735 pl011_write(uap->dmacr, uap, REG_DMACR); 736 uap->im &= ~UART011_TXIM; 737 pl011_write(uap->im, uap, REG_IMSC); 738 return true; 739 } 740 741 /* 742 * We don't have a TX buffer queued, so try to queue one. 743 * If we successfully queued a buffer, mask the TX IRQ. 744 */ 745 if (pl011_dma_tx_refill(uap) > 0) { 746 uap->im &= ~UART011_TXIM; 747 pl011_write(uap->im, uap, REG_IMSC); 748 return true; 749 } 750 return false; 751 } 752 753 /* 754 * Stop the DMA transmit (eg, due to received XOFF). 755 * Locking: called with port lock held and IRQs disabled. 756 */ 757 static inline void pl011_dma_tx_stop(struct uart_amba_port *uap) 758 { 759 if (uap->dmatx.queued) { 760 uap->dmacr &= ~UART011_TXDMAE; 761 pl011_write(uap->dmacr, uap, REG_DMACR); 762 } 763 } 764 765 /* 766 * Try to start a DMA transmit, or in the case of an XON/OFF 767 * character queued for send, try to get that character out ASAP. 768 * Locking: called with port lock held and IRQs disabled. 769 * Returns: 770 * false if we want the TX IRQ to be enabled 771 * true if we have a buffer queued 772 */ 773 static inline bool pl011_dma_tx_start(struct uart_amba_port *uap) 774 { 775 u16 dmacr; 776 777 if (!uap->using_tx_dma) 778 return false; 779 780 if (!uap->port.x_char) { 781 /* no X-char, try to push chars out in DMA mode */ 782 bool ret = true; 783 784 if (!uap->dmatx.queued) { 785 if (pl011_dma_tx_refill(uap) > 0) { 786 uap->im &= ~UART011_TXIM; 787 pl011_write(uap->im, uap, REG_IMSC); 788 } else 789 ret = false; 790 } else if (!(uap->dmacr & UART011_TXDMAE)) { 791 uap->dmacr |= UART011_TXDMAE; 792 pl011_write(uap->dmacr, uap, REG_DMACR); 793 } 794 return ret; 795 } 796 797 /* 798 * We have an X-char to send. Disable DMA to prevent it loading 799 * the TX fifo, and then see if we can stuff it into the FIFO. 800 */ 801 dmacr = uap->dmacr; 802 uap->dmacr &= ~UART011_TXDMAE; 803 pl011_write(uap->dmacr, uap, REG_DMACR); 804 805 if (pl011_read(uap, REG_FR) & UART01x_FR_TXFF) { 806 /* 807 * No space in the FIFO, so enable the transmit interrupt 808 * so we know when there is space. Note that once we've 809 * loaded the character, we should just re-enable DMA. 810 */ 811 return false; 812 } 813 814 pl011_write(uap->port.x_char, uap, REG_DR); 815 uap->port.icount.tx++; 816 uap->port.x_char = 0; 817 818 /* Success - restore the DMA state */ 819 uap->dmacr = dmacr; 820 pl011_write(dmacr, uap, REG_DMACR); 821 822 return true; 823 } 824 825 /* 826 * Flush the transmit buffer. 827 * Locking: called with port lock held and IRQs disabled. 828 */ 829 static void pl011_dma_flush_buffer(struct uart_port *port) 830 __releases(&uap->port.lock) 831 __acquires(&uap->port.lock) 832 { 833 struct uart_amba_port *uap = 834 container_of(port, struct uart_amba_port, port); 835 836 if (!uap->using_tx_dma) 837 return; 838 839 /* Avoid deadlock with the DMA engine callback */ 840 spin_unlock(&uap->port.lock); 841 dmaengine_terminate_all(uap->dmatx.chan); 842 spin_lock(&uap->port.lock); 843 if (uap->dmatx.queued) { 844 dma_unmap_sg(uap->dmatx.chan->device->dev, &uap->dmatx.sg, 1, 845 DMA_TO_DEVICE); 846 uap->dmatx.queued = false; 847 uap->dmacr &= ~UART011_TXDMAE; 848 pl011_write(uap->dmacr, uap, REG_DMACR); 849 } 850 } 851 852 static void pl011_dma_rx_callback(void *data); 853 854 static int pl011_dma_rx_trigger_dma(struct uart_amba_port *uap) 855 { 856 struct dma_chan *rxchan = uap->dmarx.chan; 857 struct pl011_dmarx_data *dmarx = &uap->dmarx; 858 struct dma_async_tx_descriptor *desc; 859 struct pl011_sgbuf *sgbuf; 860 861 if (!rxchan) 862 return -EIO; 863 864 /* Start the RX DMA job */ 865 sgbuf = uap->dmarx.use_buf_b ? 866 &uap->dmarx.sgbuf_b : &uap->dmarx.sgbuf_a; 867 desc = dmaengine_prep_slave_sg(rxchan, &sgbuf->sg, 1, 868 DMA_DEV_TO_MEM, 869 DMA_PREP_INTERRUPT | DMA_CTRL_ACK); 870 /* 871 * If the DMA engine is busy and cannot prepare a 872 * channel, no big deal, the driver will fall back 873 * to interrupt mode as a result of this error code. 874 */ 875 if (!desc) { 876 uap->dmarx.running = false; 877 dmaengine_terminate_all(rxchan); 878 return -EBUSY; 879 } 880 881 /* Some data to go along to the callback */ 882 desc->callback = pl011_dma_rx_callback; 883 desc->callback_param = uap; 884 dmarx->cookie = dmaengine_submit(desc); 885 dma_async_issue_pending(rxchan); 886 887 uap->dmacr |= UART011_RXDMAE; 888 pl011_write(uap->dmacr, uap, REG_DMACR); 889 uap->dmarx.running = true; 890 891 uap->im &= ~UART011_RXIM; 892 pl011_write(uap->im, uap, REG_IMSC); 893 894 return 0; 895 } 896 897 /* 898 * This is called when either the DMA job is complete, or 899 * the FIFO timeout interrupt occurred. This must be called 900 * with the port spinlock uap->port.lock held. 901 */ 902 static void pl011_dma_rx_chars(struct uart_amba_port *uap, 903 u32 pending, bool use_buf_b, 904 bool readfifo) 905 { 906 struct tty_port *port = &uap->port.state->port; 907 struct pl011_sgbuf *sgbuf = use_buf_b ? 908 &uap->dmarx.sgbuf_b : &uap->dmarx.sgbuf_a; 909 int dma_count = 0; 910 u32 fifotaken = 0; /* only used for vdbg() */ 911 912 struct pl011_dmarx_data *dmarx = &uap->dmarx; 913 int dmataken = 0; 914 915 if (uap->dmarx.poll_rate) { 916 /* The data can be taken by polling */ 917 dmataken = sgbuf->sg.length - dmarx->last_residue; 918 /* Recalculate the pending size */ 919 if (pending >= dmataken) 920 pending -= dmataken; 921 } 922 923 /* Pick the remain data from the DMA */ 924 if (pending) { 925 926 /* 927 * First take all chars in the DMA pipe, then look in the FIFO. 928 * Note that tty_insert_flip_buf() tries to take as many chars 929 * as it can. 930 */ 931 dma_count = tty_insert_flip_string(port, sgbuf->buf + dmataken, 932 pending); 933 934 uap->port.icount.rx += dma_count; 935 if (dma_count < pending) 936 dev_warn(uap->port.dev, 937 "couldn't insert all characters (TTY is full?)\n"); 938 } 939 940 /* Reset the last_residue for Rx DMA poll */ 941 if (uap->dmarx.poll_rate) 942 dmarx->last_residue = sgbuf->sg.length; 943 944 /* 945 * Only continue with trying to read the FIFO if all DMA chars have 946 * been taken first. 947 */ 948 if (dma_count == pending && readfifo) { 949 /* Clear any error flags */ 950 pl011_write(UART011_OEIS | UART011_BEIS | UART011_PEIS | 951 UART011_FEIS, uap, REG_ICR); 952 953 /* 954 * If we read all the DMA'd characters, and we had an 955 * incomplete buffer, that could be due to an rx error, or 956 * maybe we just timed out. Read any pending chars and check 957 * the error status. 958 * 959 * Error conditions will only occur in the FIFO, these will 960 * trigger an immediate interrupt and stop the DMA job, so we 961 * will always find the error in the FIFO, never in the DMA 962 * buffer. 963 */ 964 fifotaken = pl011_fifo_to_tty(uap); 965 } 966 967 spin_unlock(&uap->port.lock); 968 dev_vdbg(uap->port.dev, 969 "Took %d chars from DMA buffer and %d chars from the FIFO\n", 970 dma_count, fifotaken); 971 tty_flip_buffer_push(port); 972 spin_lock(&uap->port.lock); 973 } 974 975 static void pl011_dma_rx_irq(struct uart_amba_port *uap) 976 { 977 struct pl011_dmarx_data *dmarx = &uap->dmarx; 978 struct dma_chan *rxchan = dmarx->chan; 979 struct pl011_sgbuf *sgbuf = dmarx->use_buf_b ? 980 &dmarx->sgbuf_b : &dmarx->sgbuf_a; 981 size_t pending; 982 struct dma_tx_state state; 983 enum dma_status dmastat; 984 985 /* 986 * Pause the transfer so we can trust the current counter, 987 * do this before we pause the PL011 block, else we may 988 * overflow the FIFO. 989 */ 990 if (dmaengine_pause(rxchan)) 991 dev_err(uap->port.dev, "unable to pause DMA transfer\n"); 992 dmastat = rxchan->device->device_tx_status(rxchan, 993 dmarx->cookie, &state); 994 if (dmastat != DMA_PAUSED) 995 dev_err(uap->port.dev, "unable to pause DMA transfer\n"); 996 997 /* Disable RX DMA - incoming data will wait in the FIFO */ 998 uap->dmacr &= ~UART011_RXDMAE; 999 pl011_write(uap->dmacr, uap, REG_DMACR); 1000 uap->dmarx.running = false; 1001 1002 pending = sgbuf->sg.length - state.residue; 1003 BUG_ON(pending > PL011_DMA_BUFFER_SIZE); 1004 /* Then we terminate the transfer - we now know our residue */ 1005 dmaengine_terminate_all(rxchan); 1006 1007 /* 1008 * This will take the chars we have so far and insert 1009 * into the framework. 1010 */ 1011 pl011_dma_rx_chars(uap, pending, dmarx->use_buf_b, true); 1012 1013 /* Switch buffer & re-trigger DMA job */ 1014 dmarx->use_buf_b = !dmarx->use_buf_b; 1015 if (pl011_dma_rx_trigger_dma(uap)) { 1016 dev_dbg(uap->port.dev, "could not retrigger RX DMA job " 1017 "fall back to interrupt mode\n"); 1018 uap->im |= UART011_RXIM; 1019 pl011_write(uap->im, uap, REG_IMSC); 1020 } 1021 } 1022 1023 static void pl011_dma_rx_callback(void *data) 1024 { 1025 struct uart_amba_port *uap = data; 1026 struct pl011_dmarx_data *dmarx = &uap->dmarx; 1027 struct dma_chan *rxchan = dmarx->chan; 1028 bool lastbuf = dmarx->use_buf_b; 1029 struct pl011_sgbuf *sgbuf = dmarx->use_buf_b ? 1030 &dmarx->sgbuf_b : &dmarx->sgbuf_a; 1031 size_t pending; 1032 struct dma_tx_state state; 1033 int ret; 1034 1035 /* 1036 * This completion interrupt occurs typically when the 1037 * RX buffer is totally stuffed but no timeout has yet 1038 * occurred. When that happens, we just want the RX 1039 * routine to flush out the secondary DMA buffer while 1040 * we immediately trigger the next DMA job. 1041 */ 1042 spin_lock_irq(&uap->port.lock); 1043 /* 1044 * Rx data can be taken by the UART interrupts during 1045 * the DMA irq handler. So we check the residue here. 1046 */ 1047 rxchan->device->device_tx_status(rxchan, dmarx->cookie, &state); 1048 pending = sgbuf->sg.length - state.residue; 1049 BUG_ON(pending > PL011_DMA_BUFFER_SIZE); 1050 /* Then we terminate the transfer - we now know our residue */ 1051 dmaengine_terminate_all(rxchan); 1052 1053 uap->dmarx.running = false; 1054 dmarx->use_buf_b = !lastbuf; 1055 ret = pl011_dma_rx_trigger_dma(uap); 1056 1057 pl011_dma_rx_chars(uap, pending, lastbuf, false); 1058 spin_unlock_irq(&uap->port.lock); 1059 /* 1060 * Do this check after we picked the DMA chars so we don't 1061 * get some IRQ immediately from RX. 1062 */ 1063 if (ret) { 1064 dev_dbg(uap->port.dev, "could not retrigger RX DMA job " 1065 "fall back to interrupt mode\n"); 1066 uap->im |= UART011_RXIM; 1067 pl011_write(uap->im, uap, REG_IMSC); 1068 } 1069 } 1070 1071 /* 1072 * Stop accepting received characters, when we're shutting down or 1073 * suspending this port. 1074 * Locking: called with port lock held and IRQs disabled. 1075 */ 1076 static inline void pl011_dma_rx_stop(struct uart_amba_port *uap) 1077 { 1078 /* FIXME. Just disable the DMA enable */ 1079 uap->dmacr &= ~UART011_RXDMAE; 1080 pl011_write(uap->dmacr, uap, REG_DMACR); 1081 } 1082 1083 /* 1084 * Timer handler for Rx DMA polling. 1085 * Every polling, It checks the residue in the dma buffer and transfer 1086 * data to the tty. Also, last_residue is updated for the next polling. 1087 */ 1088 static void pl011_dma_rx_poll(unsigned long args) 1089 { 1090 struct uart_amba_port *uap = (struct uart_amba_port *)args; 1091 struct tty_port *port = &uap->port.state->port; 1092 struct pl011_dmarx_data *dmarx = &uap->dmarx; 1093 struct dma_chan *rxchan = uap->dmarx.chan; 1094 unsigned long flags = 0; 1095 unsigned int dmataken = 0; 1096 unsigned int size = 0; 1097 struct pl011_sgbuf *sgbuf; 1098 int dma_count; 1099 struct dma_tx_state state; 1100 1101 sgbuf = dmarx->use_buf_b ? &uap->dmarx.sgbuf_b : &uap->dmarx.sgbuf_a; 1102 rxchan->device->device_tx_status(rxchan, dmarx->cookie, &state); 1103 if (likely(state.residue < dmarx->last_residue)) { 1104 dmataken = sgbuf->sg.length - dmarx->last_residue; 1105 size = dmarx->last_residue - state.residue; 1106 dma_count = tty_insert_flip_string(port, sgbuf->buf + dmataken, 1107 size); 1108 if (dma_count == size) 1109 dmarx->last_residue = state.residue; 1110 dmarx->last_jiffies = jiffies; 1111 } 1112 tty_flip_buffer_push(port); 1113 1114 /* 1115 * If no data is received in poll_timeout, the driver will fall back 1116 * to interrupt mode. We will retrigger DMA at the first interrupt. 1117 */ 1118 if (jiffies_to_msecs(jiffies - dmarx->last_jiffies) 1119 > uap->dmarx.poll_timeout) { 1120 1121 spin_lock_irqsave(&uap->port.lock, flags); 1122 pl011_dma_rx_stop(uap); 1123 uap->im |= UART011_RXIM; 1124 pl011_write(uap->im, uap, REG_IMSC); 1125 spin_unlock_irqrestore(&uap->port.lock, flags); 1126 1127 uap->dmarx.running = false; 1128 dmaengine_terminate_all(rxchan); 1129 del_timer(&uap->dmarx.timer); 1130 } else { 1131 mod_timer(&uap->dmarx.timer, 1132 jiffies + msecs_to_jiffies(uap->dmarx.poll_rate)); 1133 } 1134 } 1135 1136 static void pl011_dma_startup(struct uart_amba_port *uap) 1137 { 1138 int ret; 1139 1140 if (!uap->dma_probed) 1141 pl011_dma_probe(uap); 1142 1143 if (!uap->dmatx.chan) 1144 return; 1145 1146 uap->dmatx.buf = kmalloc(PL011_DMA_BUFFER_SIZE, GFP_KERNEL | __GFP_DMA); 1147 if (!uap->dmatx.buf) { 1148 dev_err(uap->port.dev, "no memory for DMA TX buffer\n"); 1149 uap->port.fifosize = uap->fifosize; 1150 return; 1151 } 1152 1153 sg_init_one(&uap->dmatx.sg, uap->dmatx.buf, PL011_DMA_BUFFER_SIZE); 1154 1155 /* The DMA buffer is now the FIFO the TTY subsystem can use */ 1156 uap->port.fifosize = PL011_DMA_BUFFER_SIZE; 1157 uap->using_tx_dma = true; 1158 1159 if (!uap->dmarx.chan) 1160 goto skip_rx; 1161 1162 /* Allocate and map DMA RX buffers */ 1163 ret = pl011_sgbuf_init(uap->dmarx.chan, &uap->dmarx.sgbuf_a, 1164 DMA_FROM_DEVICE); 1165 if (ret) { 1166 dev_err(uap->port.dev, "failed to init DMA %s: %d\n", 1167 "RX buffer A", ret); 1168 goto skip_rx; 1169 } 1170 1171 ret = pl011_sgbuf_init(uap->dmarx.chan, &uap->dmarx.sgbuf_b, 1172 DMA_FROM_DEVICE); 1173 if (ret) { 1174 dev_err(uap->port.dev, "failed to init DMA %s: %d\n", 1175 "RX buffer B", ret); 1176 pl011_sgbuf_free(uap->dmarx.chan, &uap->dmarx.sgbuf_a, 1177 DMA_FROM_DEVICE); 1178 goto skip_rx; 1179 } 1180 1181 uap->using_rx_dma = true; 1182 1183 skip_rx: 1184 /* Turn on DMA error (RX/TX will be enabled on demand) */ 1185 uap->dmacr |= UART011_DMAONERR; 1186 pl011_write(uap->dmacr, uap, REG_DMACR); 1187 1188 /* 1189 * ST Micro variants has some specific dma burst threshold 1190 * compensation. Set this to 16 bytes, so burst will only 1191 * be issued above/below 16 bytes. 1192 */ 1193 if (uap->vendor->dma_threshold) 1194 pl011_write(ST_UART011_DMAWM_RX_16 | ST_UART011_DMAWM_TX_16, 1195 uap, REG_ST_DMAWM); 1196 1197 if (uap->using_rx_dma) { 1198 if (pl011_dma_rx_trigger_dma(uap)) 1199 dev_dbg(uap->port.dev, "could not trigger initial " 1200 "RX DMA job, fall back to interrupt mode\n"); 1201 if (uap->dmarx.poll_rate) { 1202 init_timer(&(uap->dmarx.timer)); 1203 uap->dmarx.timer.function = pl011_dma_rx_poll; 1204 uap->dmarx.timer.data = (unsigned long)uap; 1205 mod_timer(&uap->dmarx.timer, 1206 jiffies + 1207 msecs_to_jiffies(uap->dmarx.poll_rate)); 1208 uap->dmarx.last_residue = PL011_DMA_BUFFER_SIZE; 1209 uap->dmarx.last_jiffies = jiffies; 1210 } 1211 } 1212 } 1213 1214 static void pl011_dma_shutdown(struct uart_amba_port *uap) 1215 { 1216 if (!(uap->using_tx_dma || uap->using_rx_dma)) 1217 return; 1218 1219 /* Disable RX and TX DMA */ 1220 while (pl011_read(uap, REG_FR) & uap->vendor->fr_busy) 1221 cpu_relax(); 1222 1223 spin_lock_irq(&uap->port.lock); 1224 uap->dmacr &= ~(UART011_DMAONERR | UART011_RXDMAE | UART011_TXDMAE); 1225 pl011_write(uap->dmacr, uap, REG_DMACR); 1226 spin_unlock_irq(&uap->port.lock); 1227 1228 if (uap->using_tx_dma) { 1229 /* In theory, this should already be done by pl011_dma_flush_buffer */ 1230 dmaengine_terminate_all(uap->dmatx.chan); 1231 if (uap->dmatx.queued) { 1232 dma_unmap_sg(uap->dmatx.chan->device->dev, &uap->dmatx.sg, 1, 1233 DMA_TO_DEVICE); 1234 uap->dmatx.queued = false; 1235 } 1236 1237 kfree(uap->dmatx.buf); 1238 uap->using_tx_dma = false; 1239 } 1240 1241 if (uap->using_rx_dma) { 1242 dmaengine_terminate_all(uap->dmarx.chan); 1243 /* Clean up the RX DMA */ 1244 pl011_sgbuf_free(uap->dmarx.chan, &uap->dmarx.sgbuf_a, DMA_FROM_DEVICE); 1245 pl011_sgbuf_free(uap->dmarx.chan, &uap->dmarx.sgbuf_b, DMA_FROM_DEVICE); 1246 if (uap->dmarx.poll_rate) 1247 del_timer_sync(&uap->dmarx.timer); 1248 uap->using_rx_dma = false; 1249 } 1250 } 1251 1252 static inline bool pl011_dma_rx_available(struct uart_amba_port *uap) 1253 { 1254 return uap->using_rx_dma; 1255 } 1256 1257 static inline bool pl011_dma_rx_running(struct uart_amba_port *uap) 1258 { 1259 return uap->using_rx_dma && uap->dmarx.running; 1260 } 1261 1262 #else 1263 /* Blank functions if the DMA engine is not available */ 1264 static inline void pl011_dma_probe(struct uart_amba_port *uap) 1265 { 1266 } 1267 1268 static inline void pl011_dma_remove(struct uart_amba_port *uap) 1269 { 1270 } 1271 1272 static inline void pl011_dma_startup(struct uart_amba_port *uap) 1273 { 1274 } 1275 1276 static inline void pl011_dma_shutdown(struct uart_amba_port *uap) 1277 { 1278 } 1279 1280 static inline bool pl011_dma_tx_irq(struct uart_amba_port *uap) 1281 { 1282 return false; 1283 } 1284 1285 static inline void pl011_dma_tx_stop(struct uart_amba_port *uap) 1286 { 1287 } 1288 1289 static inline bool pl011_dma_tx_start(struct uart_amba_port *uap) 1290 { 1291 return false; 1292 } 1293 1294 static inline void pl011_dma_rx_irq(struct uart_amba_port *uap) 1295 { 1296 } 1297 1298 static inline void pl011_dma_rx_stop(struct uart_amba_port *uap) 1299 { 1300 } 1301 1302 static inline int pl011_dma_rx_trigger_dma(struct uart_amba_port *uap) 1303 { 1304 return -EIO; 1305 } 1306 1307 static inline bool pl011_dma_rx_available(struct uart_amba_port *uap) 1308 { 1309 return false; 1310 } 1311 1312 static inline bool pl011_dma_rx_running(struct uart_amba_port *uap) 1313 { 1314 return false; 1315 } 1316 1317 #define pl011_dma_flush_buffer NULL 1318 #endif 1319 1320 static void pl011_stop_tx(struct uart_port *port) 1321 { 1322 struct uart_amba_port *uap = 1323 container_of(port, struct uart_amba_port, port); 1324 1325 uap->im &= ~UART011_TXIM; 1326 pl011_write(uap->im, uap, REG_IMSC); 1327 pl011_dma_tx_stop(uap); 1328 } 1329 1330 static void pl011_tx_chars(struct uart_amba_port *uap, bool from_irq); 1331 1332 /* Start TX with programmed I/O only (no DMA) */ 1333 static void pl011_start_tx_pio(struct uart_amba_port *uap) 1334 { 1335 uap->im |= UART011_TXIM; 1336 pl011_write(uap->im, uap, REG_IMSC); 1337 pl011_tx_chars(uap, false); 1338 } 1339 1340 static void pl011_start_tx(struct uart_port *port) 1341 { 1342 struct uart_amba_port *uap = 1343 container_of(port, struct uart_amba_port, port); 1344 1345 if (!pl011_dma_tx_start(uap)) 1346 pl011_start_tx_pio(uap); 1347 } 1348 1349 static void pl011_stop_rx(struct uart_port *port) 1350 { 1351 struct uart_amba_port *uap = 1352 container_of(port, struct uart_amba_port, port); 1353 1354 uap->im &= ~(UART011_RXIM|UART011_RTIM|UART011_FEIM| 1355 UART011_PEIM|UART011_BEIM|UART011_OEIM); 1356 pl011_write(uap->im, uap, REG_IMSC); 1357 1358 pl011_dma_rx_stop(uap); 1359 } 1360 1361 static void pl011_enable_ms(struct uart_port *port) 1362 { 1363 struct uart_amba_port *uap = 1364 container_of(port, struct uart_amba_port, port); 1365 1366 uap->im |= UART011_RIMIM|UART011_CTSMIM|UART011_DCDMIM|UART011_DSRMIM; 1367 pl011_write(uap->im, uap, REG_IMSC); 1368 } 1369 1370 static void pl011_rx_chars(struct uart_amba_port *uap) 1371 __releases(&uap->port.lock) 1372 __acquires(&uap->port.lock) 1373 { 1374 pl011_fifo_to_tty(uap); 1375 1376 spin_unlock(&uap->port.lock); 1377 tty_flip_buffer_push(&uap->port.state->port); 1378 /* 1379 * If we were temporarily out of DMA mode for a while, 1380 * attempt to switch back to DMA mode again. 1381 */ 1382 if (pl011_dma_rx_available(uap)) { 1383 if (pl011_dma_rx_trigger_dma(uap)) { 1384 dev_dbg(uap->port.dev, "could not trigger RX DMA job " 1385 "fall back to interrupt mode again\n"); 1386 uap->im |= UART011_RXIM; 1387 pl011_write(uap->im, uap, REG_IMSC); 1388 } else { 1389 #ifdef CONFIG_DMA_ENGINE 1390 /* Start Rx DMA poll */ 1391 if (uap->dmarx.poll_rate) { 1392 uap->dmarx.last_jiffies = jiffies; 1393 uap->dmarx.last_residue = PL011_DMA_BUFFER_SIZE; 1394 mod_timer(&uap->dmarx.timer, 1395 jiffies + 1396 msecs_to_jiffies(uap->dmarx.poll_rate)); 1397 } 1398 #endif 1399 } 1400 } 1401 spin_lock(&uap->port.lock); 1402 } 1403 1404 static bool pl011_tx_char(struct uart_amba_port *uap, unsigned char c, 1405 bool from_irq) 1406 { 1407 if (unlikely(!from_irq) && 1408 pl011_read(uap, REG_FR) & UART01x_FR_TXFF) 1409 return false; /* unable to transmit character */ 1410 1411 pl011_write(c, uap, REG_DR); 1412 uap->port.icount.tx++; 1413 1414 return true; 1415 } 1416 1417 static void pl011_tx_chars(struct uart_amba_port *uap, bool from_irq) 1418 { 1419 struct circ_buf *xmit = &uap->port.state->xmit; 1420 int count = uap->fifosize >> 1; 1421 1422 if (uap->port.x_char) { 1423 if (!pl011_tx_char(uap, uap->port.x_char, from_irq)) 1424 return; 1425 uap->port.x_char = 0; 1426 --count; 1427 } 1428 if (uart_circ_empty(xmit) || uart_tx_stopped(&uap->port)) { 1429 pl011_stop_tx(&uap->port); 1430 return; 1431 } 1432 1433 /* If we are using DMA mode, try to send some characters. */ 1434 if (pl011_dma_tx_irq(uap)) 1435 return; 1436 1437 do { 1438 if (likely(from_irq) && count-- == 0) 1439 break; 1440 1441 if (!pl011_tx_char(uap, xmit->buf[xmit->tail], from_irq)) 1442 break; 1443 1444 xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1); 1445 } while (!uart_circ_empty(xmit)); 1446 1447 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) 1448 uart_write_wakeup(&uap->port); 1449 1450 if (uart_circ_empty(xmit)) 1451 pl011_stop_tx(&uap->port); 1452 } 1453 1454 static void pl011_modem_status(struct uart_amba_port *uap) 1455 { 1456 unsigned int status, delta; 1457 1458 status = pl011_read(uap, REG_FR) & UART01x_FR_MODEM_ANY; 1459 1460 delta = status ^ uap->old_status; 1461 uap->old_status = status; 1462 1463 if (!delta) 1464 return; 1465 1466 if (delta & UART01x_FR_DCD) 1467 uart_handle_dcd_change(&uap->port, status & UART01x_FR_DCD); 1468 1469 if (delta & uap->vendor->fr_dsr) 1470 uap->port.icount.dsr++; 1471 1472 if (delta & uap->vendor->fr_cts) 1473 uart_handle_cts_change(&uap->port, 1474 status & uap->vendor->fr_cts); 1475 1476 wake_up_interruptible(&uap->port.state->port.delta_msr_wait); 1477 } 1478 1479 static void check_apply_cts_event_workaround(struct uart_amba_port *uap) 1480 { 1481 unsigned int dummy_read; 1482 1483 if (!uap->vendor->cts_event_workaround) 1484 return; 1485 1486 /* workaround to make sure that all bits are unlocked.. */ 1487 pl011_write(0x00, uap, REG_ICR); 1488 1489 /* 1490 * WA: introduce 26ns(1 uart clk) delay before W1C; 1491 * single apb access will incur 2 pclk(133.12Mhz) delay, 1492 * so add 2 dummy reads 1493 */ 1494 dummy_read = pl011_read(uap, REG_ICR); 1495 dummy_read = pl011_read(uap, REG_ICR); 1496 } 1497 1498 static irqreturn_t pl011_int(int irq, void *dev_id) 1499 { 1500 struct uart_amba_port *uap = dev_id; 1501 unsigned long flags; 1502 unsigned int status, pass_counter = AMBA_ISR_PASS_LIMIT; 1503 u16 imsc; 1504 int handled = 0; 1505 1506 spin_lock_irqsave(&uap->port.lock, flags); 1507 imsc = pl011_read(uap, REG_IMSC); 1508 status = pl011_read(uap, REG_RIS) & imsc; 1509 if (status) { 1510 do { 1511 check_apply_cts_event_workaround(uap); 1512 1513 pl011_write(status & ~(UART011_TXIS|UART011_RTIS| 1514 UART011_RXIS), 1515 uap, REG_ICR); 1516 1517 if (status & (UART011_RTIS|UART011_RXIS)) { 1518 if (pl011_dma_rx_running(uap)) 1519 pl011_dma_rx_irq(uap); 1520 else 1521 pl011_rx_chars(uap); 1522 } 1523 if (status & (UART011_DSRMIS|UART011_DCDMIS| 1524 UART011_CTSMIS|UART011_RIMIS)) 1525 pl011_modem_status(uap); 1526 if (status & UART011_TXIS) 1527 pl011_tx_chars(uap, true); 1528 1529 if (pass_counter-- == 0) 1530 break; 1531 1532 status = pl011_read(uap, REG_RIS) & imsc; 1533 } while (status != 0); 1534 handled = 1; 1535 } 1536 1537 spin_unlock_irqrestore(&uap->port.lock, flags); 1538 1539 return IRQ_RETVAL(handled); 1540 } 1541 1542 static unsigned int pl011_tx_empty(struct uart_port *port) 1543 { 1544 struct uart_amba_port *uap = 1545 container_of(port, struct uart_amba_port, port); 1546 1547 /* Allow feature register bits to be inverted to work around errata */ 1548 unsigned int status = pl011_read(uap, REG_FR) ^ uap->vendor->inv_fr; 1549 1550 return status & (uap->vendor->fr_busy | UART01x_FR_TXFF) ? 1551 0 : TIOCSER_TEMT; 1552 } 1553 1554 static unsigned int pl011_get_mctrl(struct uart_port *port) 1555 { 1556 struct uart_amba_port *uap = 1557 container_of(port, struct uart_amba_port, port); 1558 unsigned int result = 0; 1559 unsigned int status = pl011_read(uap, REG_FR); 1560 1561 #define TIOCMBIT(uartbit, tiocmbit) \ 1562 if (status & uartbit) \ 1563 result |= tiocmbit 1564 1565 TIOCMBIT(UART01x_FR_DCD, TIOCM_CAR); 1566 TIOCMBIT(uap->vendor->fr_dsr, TIOCM_DSR); 1567 TIOCMBIT(uap->vendor->fr_cts, TIOCM_CTS); 1568 TIOCMBIT(uap->vendor->fr_ri, TIOCM_RNG); 1569 #undef TIOCMBIT 1570 return result; 1571 } 1572 1573 static void pl011_set_mctrl(struct uart_port *port, unsigned int mctrl) 1574 { 1575 struct uart_amba_port *uap = 1576 container_of(port, struct uart_amba_port, port); 1577 unsigned int cr; 1578 1579 cr = pl011_read(uap, REG_CR); 1580 1581 #define TIOCMBIT(tiocmbit, uartbit) \ 1582 if (mctrl & tiocmbit) \ 1583 cr |= uartbit; \ 1584 else \ 1585 cr &= ~uartbit 1586 1587 TIOCMBIT(TIOCM_RTS, UART011_CR_RTS); 1588 TIOCMBIT(TIOCM_DTR, UART011_CR_DTR); 1589 TIOCMBIT(TIOCM_OUT1, UART011_CR_OUT1); 1590 TIOCMBIT(TIOCM_OUT2, UART011_CR_OUT2); 1591 TIOCMBIT(TIOCM_LOOP, UART011_CR_LBE); 1592 1593 if (uap->autorts) { 1594 /* We need to disable auto-RTS if we want to turn RTS off */ 1595 TIOCMBIT(TIOCM_RTS, UART011_CR_RTSEN); 1596 } 1597 #undef TIOCMBIT 1598 1599 pl011_write(cr, uap, REG_CR); 1600 } 1601 1602 static void pl011_break_ctl(struct uart_port *port, int break_state) 1603 { 1604 struct uart_amba_port *uap = 1605 container_of(port, struct uart_amba_port, port); 1606 unsigned long flags; 1607 unsigned int lcr_h; 1608 1609 spin_lock_irqsave(&uap->port.lock, flags); 1610 lcr_h = pl011_read(uap, REG_LCRH_TX); 1611 if (break_state == -1) 1612 lcr_h |= UART01x_LCRH_BRK; 1613 else 1614 lcr_h &= ~UART01x_LCRH_BRK; 1615 pl011_write(lcr_h, uap, REG_LCRH_TX); 1616 spin_unlock_irqrestore(&uap->port.lock, flags); 1617 } 1618 1619 #ifdef CONFIG_CONSOLE_POLL 1620 1621 static void pl011_quiesce_irqs(struct uart_port *port) 1622 { 1623 struct uart_amba_port *uap = 1624 container_of(port, struct uart_amba_port, port); 1625 1626 pl011_write(pl011_read(uap, REG_MIS), uap, REG_ICR); 1627 /* 1628 * There is no way to clear TXIM as this is "ready to transmit IRQ", so 1629 * we simply mask it. start_tx() will unmask it. 1630 * 1631 * Note we can race with start_tx(), and if the race happens, the 1632 * polling user might get another interrupt just after we clear it. 1633 * But it should be OK and can happen even w/o the race, e.g. 1634 * controller immediately got some new data and raised the IRQ. 1635 * 1636 * And whoever uses polling routines assumes that it manages the device 1637 * (including tx queue), so we're also fine with start_tx()'s caller 1638 * side. 1639 */ 1640 pl011_write(pl011_read(uap, REG_IMSC) & ~UART011_TXIM, uap, 1641 REG_IMSC); 1642 } 1643 1644 static int pl011_get_poll_char(struct uart_port *port) 1645 { 1646 struct uart_amba_port *uap = 1647 container_of(port, struct uart_amba_port, port); 1648 unsigned int status; 1649 1650 /* 1651 * The caller might need IRQs lowered, e.g. if used with KDB NMI 1652 * debugger. 1653 */ 1654 pl011_quiesce_irqs(port); 1655 1656 status = pl011_read(uap, REG_FR); 1657 if (status & UART01x_FR_RXFE) 1658 return NO_POLL_CHAR; 1659 1660 return pl011_read(uap, REG_DR); 1661 } 1662 1663 static void pl011_put_poll_char(struct uart_port *port, 1664 unsigned char ch) 1665 { 1666 struct uart_amba_port *uap = 1667 container_of(port, struct uart_amba_port, port); 1668 1669 while (pl011_read(uap, REG_FR) & UART01x_FR_TXFF) 1670 cpu_relax(); 1671 1672 pl011_write(ch, uap, REG_DR); 1673 } 1674 1675 #endif /* CONFIG_CONSOLE_POLL */ 1676 1677 static int pl011_hwinit(struct uart_port *port) 1678 { 1679 struct uart_amba_port *uap = 1680 container_of(port, struct uart_amba_port, port); 1681 int retval; 1682 1683 /* Optionaly enable pins to be muxed in and configured */ 1684 pinctrl_pm_select_default_state(port->dev); 1685 1686 /* 1687 * Try to enable the clock producer. 1688 */ 1689 retval = clk_prepare_enable(uap->clk); 1690 if (retval) 1691 return retval; 1692 1693 uap->port.uartclk = clk_get_rate(uap->clk); 1694 1695 /* Clear pending error and receive interrupts */ 1696 pl011_write(UART011_OEIS | UART011_BEIS | UART011_PEIS | 1697 UART011_FEIS | UART011_RTIS | UART011_RXIS, 1698 uap, REG_ICR); 1699 1700 /* 1701 * Save interrupts enable mask, and enable RX interrupts in case if 1702 * the interrupt is used for NMI entry. 1703 */ 1704 uap->im = pl011_read(uap, REG_IMSC); 1705 pl011_write(UART011_RTIM | UART011_RXIM, uap, REG_IMSC); 1706 1707 if (dev_get_platdata(uap->port.dev)) { 1708 struct amba_pl011_data *plat; 1709 1710 plat = dev_get_platdata(uap->port.dev); 1711 if (plat->init) 1712 plat->init(); 1713 } 1714 return 0; 1715 } 1716 1717 static bool pl011_split_lcrh(const struct uart_amba_port *uap) 1718 { 1719 return pl011_reg_to_offset(uap, REG_LCRH_RX) != 1720 pl011_reg_to_offset(uap, REG_LCRH_TX); 1721 } 1722 1723 static void pl011_write_lcr_h(struct uart_amba_port *uap, unsigned int lcr_h) 1724 { 1725 pl011_write(lcr_h, uap, REG_LCRH_RX); 1726 if (pl011_split_lcrh(uap)) { 1727 int i; 1728 /* 1729 * Wait 10 PCLKs before writing LCRH_TX register, 1730 * to get this delay write read only register 10 times 1731 */ 1732 for (i = 0; i < 10; ++i) 1733 pl011_write(0xff, uap, REG_MIS); 1734 pl011_write(lcr_h, uap, REG_LCRH_TX); 1735 } 1736 } 1737 1738 static int pl011_allocate_irq(struct uart_amba_port *uap) 1739 { 1740 pl011_write(uap->im, uap, REG_IMSC); 1741 1742 return request_irq(uap->port.irq, pl011_int, 0, "uart-pl011", uap); 1743 } 1744 1745 /* 1746 * Enable interrupts, only timeouts when using DMA 1747 * if initial RX DMA job failed, start in interrupt mode 1748 * as well. 1749 */ 1750 static void pl011_enable_interrupts(struct uart_amba_port *uap) 1751 { 1752 spin_lock_irq(&uap->port.lock); 1753 1754 /* Clear out any spuriously appearing RX interrupts */ 1755 pl011_write(UART011_RTIS | UART011_RXIS, uap, REG_ICR); 1756 uap->im = UART011_RTIM; 1757 if (!pl011_dma_rx_running(uap)) 1758 uap->im |= UART011_RXIM; 1759 pl011_write(uap->im, uap, REG_IMSC); 1760 spin_unlock_irq(&uap->port.lock); 1761 } 1762 1763 static int pl011_startup(struct uart_port *port) 1764 { 1765 struct uart_amba_port *uap = 1766 container_of(port, struct uart_amba_port, port); 1767 unsigned int cr; 1768 int retval; 1769 1770 retval = pl011_hwinit(port); 1771 if (retval) 1772 goto clk_dis; 1773 1774 retval = pl011_allocate_irq(uap); 1775 if (retval) 1776 goto clk_dis; 1777 1778 pl011_write(uap->vendor->ifls, uap, REG_IFLS); 1779 1780 spin_lock_irq(&uap->port.lock); 1781 1782 /* restore RTS and DTR */ 1783 cr = uap->old_cr & (UART011_CR_RTS | UART011_CR_DTR); 1784 cr |= UART01x_CR_UARTEN | UART011_CR_RXE | UART011_CR_TXE; 1785 pl011_write(cr, uap, REG_CR); 1786 1787 spin_unlock_irq(&uap->port.lock); 1788 1789 /* 1790 * initialise the old status of the modem signals 1791 */ 1792 uap->old_status = pl011_read(uap, REG_FR) & UART01x_FR_MODEM_ANY; 1793 1794 /* Startup DMA */ 1795 pl011_dma_startup(uap); 1796 1797 pl011_enable_interrupts(uap); 1798 1799 return 0; 1800 1801 clk_dis: 1802 clk_disable_unprepare(uap->clk); 1803 return retval; 1804 } 1805 1806 static int sbsa_uart_startup(struct uart_port *port) 1807 { 1808 struct uart_amba_port *uap = 1809 container_of(port, struct uart_amba_port, port); 1810 int retval; 1811 1812 retval = pl011_hwinit(port); 1813 if (retval) 1814 return retval; 1815 1816 retval = pl011_allocate_irq(uap); 1817 if (retval) 1818 return retval; 1819 1820 /* The SBSA UART does not support any modem status lines. */ 1821 uap->old_status = 0; 1822 1823 pl011_enable_interrupts(uap); 1824 1825 return 0; 1826 } 1827 1828 static void pl011_shutdown_channel(struct uart_amba_port *uap, 1829 unsigned int lcrh) 1830 { 1831 unsigned long val; 1832 1833 val = pl011_read(uap, lcrh); 1834 val &= ~(UART01x_LCRH_BRK | UART01x_LCRH_FEN); 1835 pl011_write(val, uap, lcrh); 1836 } 1837 1838 /* 1839 * disable the port. It should not disable RTS and DTR. 1840 * Also RTS and DTR state should be preserved to restore 1841 * it during startup(). 1842 */ 1843 static void pl011_disable_uart(struct uart_amba_port *uap) 1844 { 1845 unsigned int cr; 1846 1847 uap->autorts = false; 1848 spin_lock_irq(&uap->port.lock); 1849 cr = pl011_read(uap, REG_CR); 1850 uap->old_cr = cr; 1851 cr &= UART011_CR_RTS | UART011_CR_DTR; 1852 cr |= UART01x_CR_UARTEN | UART011_CR_TXE; 1853 pl011_write(cr, uap, REG_CR); 1854 spin_unlock_irq(&uap->port.lock); 1855 1856 /* 1857 * disable break condition and fifos 1858 */ 1859 pl011_shutdown_channel(uap, REG_LCRH_RX); 1860 if (pl011_split_lcrh(uap)) 1861 pl011_shutdown_channel(uap, REG_LCRH_TX); 1862 } 1863 1864 static void pl011_disable_interrupts(struct uart_amba_port *uap) 1865 { 1866 spin_lock_irq(&uap->port.lock); 1867 1868 /* mask all interrupts and clear all pending ones */ 1869 uap->im = 0; 1870 pl011_write(uap->im, uap, REG_IMSC); 1871 pl011_write(0xffff, uap, REG_ICR); 1872 1873 spin_unlock_irq(&uap->port.lock); 1874 } 1875 1876 static void pl011_shutdown(struct uart_port *port) 1877 { 1878 struct uart_amba_port *uap = 1879 container_of(port, struct uart_amba_port, port); 1880 1881 pl011_disable_interrupts(uap); 1882 1883 pl011_dma_shutdown(uap); 1884 1885 free_irq(uap->port.irq, uap); 1886 1887 pl011_disable_uart(uap); 1888 1889 /* 1890 * Shut down the clock producer 1891 */ 1892 clk_disable_unprepare(uap->clk); 1893 /* Optionally let pins go into sleep states */ 1894 pinctrl_pm_select_sleep_state(port->dev); 1895 1896 if (dev_get_platdata(uap->port.dev)) { 1897 struct amba_pl011_data *plat; 1898 1899 plat = dev_get_platdata(uap->port.dev); 1900 if (plat->exit) 1901 plat->exit(); 1902 } 1903 1904 if (uap->port.ops->flush_buffer) 1905 uap->port.ops->flush_buffer(port); 1906 } 1907 1908 static void sbsa_uart_shutdown(struct uart_port *port) 1909 { 1910 struct uart_amba_port *uap = 1911 container_of(port, struct uart_amba_port, port); 1912 1913 pl011_disable_interrupts(uap); 1914 1915 free_irq(uap->port.irq, uap); 1916 1917 if (uap->port.ops->flush_buffer) 1918 uap->port.ops->flush_buffer(port); 1919 } 1920 1921 static void 1922 pl011_setup_status_masks(struct uart_port *port, struct ktermios *termios) 1923 { 1924 port->read_status_mask = UART011_DR_OE | 255; 1925 if (termios->c_iflag & INPCK) 1926 port->read_status_mask |= UART011_DR_FE | UART011_DR_PE; 1927 if (termios->c_iflag & (IGNBRK | BRKINT | PARMRK)) 1928 port->read_status_mask |= UART011_DR_BE; 1929 1930 /* 1931 * Characters to ignore 1932 */ 1933 port->ignore_status_mask = 0; 1934 if (termios->c_iflag & IGNPAR) 1935 port->ignore_status_mask |= UART011_DR_FE | UART011_DR_PE; 1936 if (termios->c_iflag & IGNBRK) { 1937 port->ignore_status_mask |= UART011_DR_BE; 1938 /* 1939 * If we're ignoring parity and break indicators, 1940 * ignore overruns too (for real raw support). 1941 */ 1942 if (termios->c_iflag & IGNPAR) 1943 port->ignore_status_mask |= UART011_DR_OE; 1944 } 1945 1946 /* 1947 * Ignore all characters if CREAD is not set. 1948 */ 1949 if ((termios->c_cflag & CREAD) == 0) 1950 port->ignore_status_mask |= UART_DUMMY_DR_RX; 1951 } 1952 1953 static void 1954 pl011_set_termios(struct uart_port *port, struct ktermios *termios, 1955 struct ktermios *old) 1956 { 1957 struct uart_amba_port *uap = 1958 container_of(port, struct uart_amba_port, port); 1959 unsigned int lcr_h, old_cr; 1960 unsigned long flags; 1961 unsigned int baud, quot, clkdiv; 1962 1963 if (uap->vendor->oversampling) 1964 clkdiv = 8; 1965 else 1966 clkdiv = 16; 1967 1968 /* 1969 * Ask the core to calculate the divisor for us. 1970 */ 1971 baud = uart_get_baud_rate(port, termios, old, 0, 1972 port->uartclk / clkdiv); 1973 #ifdef CONFIG_DMA_ENGINE 1974 /* 1975 * Adjust RX DMA polling rate with baud rate if not specified. 1976 */ 1977 if (uap->dmarx.auto_poll_rate) 1978 uap->dmarx.poll_rate = DIV_ROUND_UP(10000000, baud); 1979 #endif 1980 1981 if (baud > port->uartclk/16) 1982 quot = DIV_ROUND_CLOSEST(port->uartclk * 8, baud); 1983 else 1984 quot = DIV_ROUND_CLOSEST(port->uartclk * 4, baud); 1985 1986 switch (termios->c_cflag & CSIZE) { 1987 case CS5: 1988 lcr_h = UART01x_LCRH_WLEN_5; 1989 break; 1990 case CS6: 1991 lcr_h = UART01x_LCRH_WLEN_6; 1992 break; 1993 case CS7: 1994 lcr_h = UART01x_LCRH_WLEN_7; 1995 break; 1996 default: // CS8 1997 lcr_h = UART01x_LCRH_WLEN_8; 1998 break; 1999 } 2000 if (termios->c_cflag & CSTOPB) 2001 lcr_h |= UART01x_LCRH_STP2; 2002 if (termios->c_cflag & PARENB) { 2003 lcr_h |= UART01x_LCRH_PEN; 2004 if (!(termios->c_cflag & PARODD)) 2005 lcr_h |= UART01x_LCRH_EPS; 2006 if (termios->c_cflag & CMSPAR) 2007 lcr_h |= UART011_LCRH_SPS; 2008 } 2009 if (uap->fifosize > 1) 2010 lcr_h |= UART01x_LCRH_FEN; 2011 2012 spin_lock_irqsave(&port->lock, flags); 2013 2014 /* 2015 * Update the per-port timeout. 2016 */ 2017 uart_update_timeout(port, termios->c_cflag, baud); 2018 2019 pl011_setup_status_masks(port, termios); 2020 2021 if (UART_ENABLE_MS(port, termios->c_cflag)) 2022 pl011_enable_ms(port); 2023 2024 /* first, disable everything */ 2025 old_cr = pl011_read(uap, REG_CR); 2026 pl011_write(0, uap, REG_CR); 2027 2028 if (termios->c_cflag & CRTSCTS) { 2029 if (old_cr & UART011_CR_RTS) 2030 old_cr |= UART011_CR_RTSEN; 2031 2032 old_cr |= UART011_CR_CTSEN; 2033 uap->autorts = true; 2034 } else { 2035 old_cr &= ~(UART011_CR_CTSEN | UART011_CR_RTSEN); 2036 uap->autorts = false; 2037 } 2038 2039 if (uap->vendor->oversampling) { 2040 if (baud > port->uartclk / 16) 2041 old_cr |= ST_UART011_CR_OVSFACT; 2042 else 2043 old_cr &= ~ST_UART011_CR_OVSFACT; 2044 } 2045 2046 /* 2047 * Workaround for the ST Micro oversampling variants to 2048 * increase the bitrate slightly, by lowering the divisor, 2049 * to avoid delayed sampling of start bit at high speeds, 2050 * else we see data corruption. 2051 */ 2052 if (uap->vendor->oversampling) { 2053 if ((baud >= 3000000) && (baud < 3250000) && (quot > 1)) 2054 quot -= 1; 2055 else if ((baud > 3250000) && (quot > 2)) 2056 quot -= 2; 2057 } 2058 /* Set baud rate */ 2059 pl011_write(quot & 0x3f, uap, REG_FBRD); 2060 pl011_write(quot >> 6, uap, REG_IBRD); 2061 2062 /* 2063 * ----------v----------v----------v----------v----- 2064 * NOTE: REG_LCRH_TX and REG_LCRH_RX MUST BE WRITTEN AFTER 2065 * REG_FBRD & REG_IBRD. 2066 * ----------^----------^----------^----------^----- 2067 */ 2068 pl011_write_lcr_h(uap, lcr_h); 2069 pl011_write(old_cr, uap, REG_CR); 2070 2071 spin_unlock_irqrestore(&port->lock, flags); 2072 } 2073 2074 static void 2075 sbsa_uart_set_termios(struct uart_port *port, struct ktermios *termios, 2076 struct ktermios *old) 2077 { 2078 struct uart_amba_port *uap = 2079 container_of(port, struct uart_amba_port, port); 2080 unsigned long flags; 2081 2082 tty_termios_encode_baud_rate(termios, uap->fixed_baud, uap->fixed_baud); 2083 2084 /* The SBSA UART only supports 8n1 without hardware flow control. */ 2085 termios->c_cflag &= ~(CSIZE | CSTOPB | PARENB | PARODD); 2086 termios->c_cflag &= ~(CMSPAR | CRTSCTS); 2087 termios->c_cflag |= CS8 | CLOCAL; 2088 2089 spin_lock_irqsave(&port->lock, flags); 2090 uart_update_timeout(port, CS8, uap->fixed_baud); 2091 pl011_setup_status_masks(port, termios); 2092 spin_unlock_irqrestore(&port->lock, flags); 2093 } 2094 2095 static const char *pl011_type(struct uart_port *port) 2096 { 2097 struct uart_amba_port *uap = 2098 container_of(port, struct uart_amba_port, port); 2099 return uap->port.type == PORT_AMBA ? uap->type : NULL; 2100 } 2101 2102 /* 2103 * Release the memory region(s) being used by 'port' 2104 */ 2105 static void pl011_release_port(struct uart_port *port) 2106 { 2107 release_mem_region(port->mapbase, SZ_4K); 2108 } 2109 2110 /* 2111 * Request the memory region(s) being used by 'port' 2112 */ 2113 static int pl011_request_port(struct uart_port *port) 2114 { 2115 return request_mem_region(port->mapbase, SZ_4K, "uart-pl011") 2116 != NULL ? 0 : -EBUSY; 2117 } 2118 2119 /* 2120 * Configure/autoconfigure the port. 2121 */ 2122 static void pl011_config_port(struct uart_port *port, int flags) 2123 { 2124 if (flags & UART_CONFIG_TYPE) { 2125 port->type = PORT_AMBA; 2126 pl011_request_port(port); 2127 } 2128 } 2129 2130 /* 2131 * verify the new serial_struct (for TIOCSSERIAL). 2132 */ 2133 static int pl011_verify_port(struct uart_port *port, struct serial_struct *ser) 2134 { 2135 int ret = 0; 2136 if (ser->type != PORT_UNKNOWN && ser->type != PORT_AMBA) 2137 ret = -EINVAL; 2138 if (ser->irq < 0 || ser->irq >= nr_irqs) 2139 ret = -EINVAL; 2140 if (ser->baud_base < 9600) 2141 ret = -EINVAL; 2142 return ret; 2143 } 2144 2145 static const struct uart_ops amba_pl011_pops = { 2146 .tx_empty = pl011_tx_empty, 2147 .set_mctrl = pl011_set_mctrl, 2148 .get_mctrl = pl011_get_mctrl, 2149 .stop_tx = pl011_stop_tx, 2150 .start_tx = pl011_start_tx, 2151 .stop_rx = pl011_stop_rx, 2152 .enable_ms = pl011_enable_ms, 2153 .break_ctl = pl011_break_ctl, 2154 .startup = pl011_startup, 2155 .shutdown = pl011_shutdown, 2156 .flush_buffer = pl011_dma_flush_buffer, 2157 .set_termios = pl011_set_termios, 2158 .type = pl011_type, 2159 .release_port = pl011_release_port, 2160 .request_port = pl011_request_port, 2161 .config_port = pl011_config_port, 2162 .verify_port = pl011_verify_port, 2163 #ifdef CONFIG_CONSOLE_POLL 2164 .poll_init = pl011_hwinit, 2165 .poll_get_char = pl011_get_poll_char, 2166 .poll_put_char = pl011_put_poll_char, 2167 #endif 2168 }; 2169 2170 static void sbsa_uart_set_mctrl(struct uart_port *port, unsigned int mctrl) 2171 { 2172 } 2173 2174 static unsigned int sbsa_uart_get_mctrl(struct uart_port *port) 2175 { 2176 return 0; 2177 } 2178 2179 static const struct uart_ops sbsa_uart_pops = { 2180 .tx_empty = pl011_tx_empty, 2181 .set_mctrl = sbsa_uart_set_mctrl, 2182 .get_mctrl = sbsa_uart_get_mctrl, 2183 .stop_tx = pl011_stop_tx, 2184 .start_tx = pl011_start_tx, 2185 .stop_rx = pl011_stop_rx, 2186 .startup = sbsa_uart_startup, 2187 .shutdown = sbsa_uart_shutdown, 2188 .set_termios = sbsa_uart_set_termios, 2189 .type = pl011_type, 2190 .release_port = pl011_release_port, 2191 .request_port = pl011_request_port, 2192 .config_port = pl011_config_port, 2193 .verify_port = pl011_verify_port, 2194 #ifdef CONFIG_CONSOLE_POLL 2195 .poll_init = pl011_hwinit, 2196 .poll_get_char = pl011_get_poll_char, 2197 .poll_put_char = pl011_put_poll_char, 2198 #endif 2199 }; 2200 2201 static struct uart_amba_port *amba_ports[UART_NR]; 2202 2203 #ifdef CONFIG_SERIAL_AMBA_PL011_CONSOLE 2204 2205 static void pl011_console_putchar(struct uart_port *port, int ch) 2206 { 2207 struct uart_amba_port *uap = 2208 container_of(port, struct uart_amba_port, port); 2209 2210 while (pl011_read(uap, REG_FR) & UART01x_FR_TXFF) 2211 cpu_relax(); 2212 pl011_write(ch, uap, REG_DR); 2213 } 2214 2215 static void 2216 pl011_console_write(struct console *co, const char *s, unsigned int count) 2217 { 2218 struct uart_amba_port *uap = amba_ports[co->index]; 2219 unsigned int old_cr = 0, new_cr; 2220 unsigned long flags; 2221 int locked = 1; 2222 2223 clk_enable(uap->clk); 2224 2225 local_irq_save(flags); 2226 if (uap->port.sysrq) 2227 locked = 0; 2228 else if (oops_in_progress) 2229 locked = spin_trylock(&uap->port.lock); 2230 else 2231 spin_lock(&uap->port.lock); 2232 2233 /* 2234 * First save the CR then disable the interrupts 2235 */ 2236 if (!uap->vendor->always_enabled) { 2237 old_cr = pl011_read(uap, REG_CR); 2238 new_cr = old_cr & ~UART011_CR_CTSEN; 2239 new_cr |= UART01x_CR_UARTEN | UART011_CR_TXE; 2240 pl011_write(new_cr, uap, REG_CR); 2241 } 2242 2243 uart_console_write(&uap->port, s, count, pl011_console_putchar); 2244 2245 /* 2246 * Finally, wait for transmitter to become empty and restore the 2247 * TCR. Allow feature register bits to be inverted to work around 2248 * errata. 2249 */ 2250 while ((pl011_read(uap, REG_FR) ^ uap->vendor->inv_fr) 2251 & uap->vendor->fr_busy) 2252 cpu_relax(); 2253 if (!uap->vendor->always_enabled) 2254 pl011_write(old_cr, uap, REG_CR); 2255 2256 if (locked) 2257 spin_unlock(&uap->port.lock); 2258 local_irq_restore(flags); 2259 2260 clk_disable(uap->clk); 2261 } 2262 2263 static void __init 2264 pl011_console_get_options(struct uart_amba_port *uap, int *baud, 2265 int *parity, int *bits) 2266 { 2267 if (pl011_read(uap, REG_CR) & UART01x_CR_UARTEN) { 2268 unsigned int lcr_h, ibrd, fbrd; 2269 2270 lcr_h = pl011_read(uap, REG_LCRH_TX); 2271 2272 *parity = 'n'; 2273 if (lcr_h & UART01x_LCRH_PEN) { 2274 if (lcr_h & UART01x_LCRH_EPS) 2275 *parity = 'e'; 2276 else 2277 *parity = 'o'; 2278 } 2279 2280 if ((lcr_h & 0x60) == UART01x_LCRH_WLEN_7) 2281 *bits = 7; 2282 else 2283 *bits = 8; 2284 2285 ibrd = pl011_read(uap, REG_IBRD); 2286 fbrd = pl011_read(uap, REG_FBRD); 2287 2288 *baud = uap->port.uartclk * 4 / (64 * ibrd + fbrd); 2289 2290 if (uap->vendor->oversampling) { 2291 if (pl011_read(uap, REG_CR) 2292 & ST_UART011_CR_OVSFACT) 2293 *baud *= 2; 2294 } 2295 } 2296 } 2297 2298 static int __init pl011_console_setup(struct console *co, char *options) 2299 { 2300 struct uart_amba_port *uap; 2301 int baud = 38400; 2302 int bits = 8; 2303 int parity = 'n'; 2304 int flow = 'n'; 2305 int ret; 2306 2307 /* 2308 * Check whether an invalid uart number has been specified, and 2309 * if so, search for the first available port that does have 2310 * console support. 2311 */ 2312 if (co->index >= UART_NR) 2313 co->index = 0; 2314 uap = amba_ports[co->index]; 2315 if (!uap) 2316 return -ENODEV; 2317 2318 /* Allow pins to be muxed in and configured */ 2319 pinctrl_pm_select_default_state(uap->port.dev); 2320 2321 ret = clk_prepare(uap->clk); 2322 if (ret) 2323 return ret; 2324 2325 if (dev_get_platdata(uap->port.dev)) { 2326 struct amba_pl011_data *plat; 2327 2328 plat = dev_get_platdata(uap->port.dev); 2329 if (plat->init) 2330 plat->init(); 2331 } 2332 2333 uap->port.uartclk = clk_get_rate(uap->clk); 2334 2335 if (uap->vendor->fixed_options) { 2336 baud = uap->fixed_baud; 2337 } else { 2338 if (options) 2339 uart_parse_options(options, 2340 &baud, &parity, &bits, &flow); 2341 else 2342 pl011_console_get_options(uap, &baud, &parity, &bits); 2343 } 2344 2345 return uart_set_options(&uap->port, co, baud, parity, bits, flow); 2346 } 2347 2348 /** 2349 * pl011_console_match - non-standard console matching 2350 * @co: registering console 2351 * @name: name from console command line 2352 * @idx: index from console command line 2353 * @options: ptr to option string from console command line 2354 * 2355 * Only attempts to match console command lines of the form: 2356 * console=pl011,mmio|mmio32,<addr>[,<options>] 2357 * console=pl011,0x<addr>[,<options>] 2358 * This form is used to register an initial earlycon boot console and 2359 * replace it with the amba_console at pl011 driver init. 2360 * 2361 * Performs console setup for a match (as required by interface) 2362 * If no <options> are specified, then assume the h/w is already setup. 2363 * 2364 * Returns 0 if console matches; otherwise non-zero to use default matching 2365 */ 2366 static int __init pl011_console_match(struct console *co, char *name, int idx, 2367 char *options) 2368 { 2369 unsigned char iotype; 2370 resource_size_t addr; 2371 int i; 2372 2373 if (strcmp(name, "qdf2400_e44") == 0) { 2374 pr_info_once("UART: Working around QDF2400 SoC erratum 44"); 2375 qdf2400_e44_present = true; 2376 } else if (strcmp(name, "pl011") != 0 || strcmp(name, "ttyAMA") != 0) { 2377 return -ENODEV; 2378 } 2379 2380 if (uart_parse_earlycon(options, &iotype, &addr, &options)) 2381 return -ENODEV; 2382 2383 if (iotype != UPIO_MEM && iotype != UPIO_MEM32) 2384 return -ENODEV; 2385 2386 /* try to match the port specified on the command line */ 2387 for (i = 0; i < ARRAY_SIZE(amba_ports); i++) { 2388 struct uart_port *port; 2389 2390 if (!amba_ports[i]) 2391 continue; 2392 2393 port = &amba_ports[i]->port; 2394 2395 if (port->mapbase != addr) 2396 continue; 2397 2398 co->index = i; 2399 port->cons = co; 2400 return pl011_console_setup(co, options); 2401 } 2402 2403 return -ENODEV; 2404 } 2405 2406 static struct uart_driver amba_reg; 2407 static struct console amba_console = { 2408 .name = "ttyAMA", 2409 .write = pl011_console_write, 2410 .device = uart_console_device, 2411 .setup = pl011_console_setup, 2412 .match = pl011_console_match, 2413 .flags = CON_PRINTBUFFER | CON_ANYTIME, 2414 .index = -1, 2415 .data = &amba_reg, 2416 }; 2417 2418 #define AMBA_CONSOLE (&amba_console) 2419 2420 static void qdf2400_e44_putc(struct uart_port *port, int c) 2421 { 2422 while (readl(port->membase + UART01x_FR) & UART01x_FR_TXFF) 2423 cpu_relax(); 2424 writel(c, port->membase + UART01x_DR); 2425 while (!(readl(port->membase + UART01x_FR) & UART011_FR_TXFE)) 2426 cpu_relax(); 2427 } 2428 2429 static void qdf2400_e44_early_write(struct console *con, const char *s, unsigned n) 2430 { 2431 struct earlycon_device *dev = con->data; 2432 2433 uart_console_write(&dev->port, s, n, qdf2400_e44_putc); 2434 } 2435 2436 static void pl011_putc(struct uart_port *port, int c) 2437 { 2438 while (readl(port->membase + UART01x_FR) & UART01x_FR_TXFF) 2439 cpu_relax(); 2440 if (port->iotype == UPIO_MEM32) 2441 writel(c, port->membase + UART01x_DR); 2442 else 2443 writeb(c, port->membase + UART01x_DR); 2444 while (readl(port->membase + UART01x_FR) & UART01x_FR_BUSY) 2445 cpu_relax(); 2446 } 2447 2448 static void pl011_early_write(struct console *con, const char *s, unsigned n) 2449 { 2450 struct earlycon_device *dev = con->data; 2451 2452 uart_console_write(&dev->port, s, n, pl011_putc); 2453 } 2454 2455 static int __init pl011_early_console_setup(struct earlycon_device *device, 2456 const char *opt) 2457 { 2458 if (!device->port.membase) 2459 return -ENODEV; 2460 2461 device->con->write = qdf2400_e44_present ? 2462 qdf2400_e44_early_write : pl011_early_write; 2463 return 0; 2464 } 2465 OF_EARLYCON_DECLARE(pl011, "arm,pl011", pl011_early_console_setup); 2466 OF_EARLYCON_DECLARE(pl011, "arm,sbsa-uart", pl011_early_console_setup); 2467 2468 #else 2469 #define AMBA_CONSOLE NULL 2470 #endif 2471 2472 static struct uart_driver amba_reg = { 2473 .owner = THIS_MODULE, 2474 .driver_name = "ttyAMA", 2475 .dev_name = "ttyAMA", 2476 .major = SERIAL_AMBA_MAJOR, 2477 .minor = SERIAL_AMBA_MINOR, 2478 .nr = UART_NR, 2479 .cons = AMBA_CONSOLE, 2480 }; 2481 2482 static int pl011_probe_dt_alias(int index, struct device *dev) 2483 { 2484 struct device_node *np; 2485 static bool seen_dev_with_alias = false; 2486 static bool seen_dev_without_alias = false; 2487 int ret = index; 2488 2489 if (!IS_ENABLED(CONFIG_OF)) 2490 return ret; 2491 2492 np = dev->of_node; 2493 if (!np) 2494 return ret; 2495 2496 ret = of_alias_get_id(np, "serial"); 2497 if (ret < 0) { 2498 seen_dev_without_alias = true; 2499 ret = index; 2500 } else { 2501 seen_dev_with_alias = true; 2502 if (ret >= ARRAY_SIZE(amba_ports) || amba_ports[ret] != NULL) { 2503 dev_warn(dev, "requested serial port %d not available.\n", ret); 2504 ret = index; 2505 } 2506 } 2507 2508 if (seen_dev_with_alias && seen_dev_without_alias) 2509 dev_warn(dev, "aliased and non-aliased serial devices found in device tree. Serial port enumeration may be unpredictable.\n"); 2510 2511 return ret; 2512 } 2513 2514 /* unregisters the driver also if no more ports are left */ 2515 static void pl011_unregister_port(struct uart_amba_port *uap) 2516 { 2517 int i; 2518 bool busy = false; 2519 2520 for (i = 0; i < ARRAY_SIZE(amba_ports); i++) { 2521 if (amba_ports[i] == uap) 2522 amba_ports[i] = NULL; 2523 else if (amba_ports[i]) 2524 busy = true; 2525 } 2526 pl011_dma_remove(uap); 2527 if (!busy) 2528 uart_unregister_driver(&amba_reg); 2529 } 2530 2531 static int pl011_find_free_port(void) 2532 { 2533 int i; 2534 2535 for (i = 0; i < ARRAY_SIZE(amba_ports); i++) 2536 if (amba_ports[i] == NULL) 2537 return i; 2538 2539 return -EBUSY; 2540 } 2541 2542 static int pl011_setup_port(struct device *dev, struct uart_amba_port *uap, 2543 struct resource *mmiobase, int index) 2544 { 2545 void __iomem *base; 2546 2547 base = devm_ioremap_resource(dev, mmiobase); 2548 if (IS_ERR(base)) 2549 return PTR_ERR(base); 2550 2551 index = pl011_probe_dt_alias(index, dev); 2552 2553 uap->old_cr = 0; 2554 uap->port.dev = dev; 2555 uap->port.mapbase = mmiobase->start; 2556 uap->port.membase = base; 2557 uap->port.fifosize = uap->fifosize; 2558 uap->port.flags = UPF_BOOT_AUTOCONF; 2559 uap->port.line = index; 2560 2561 amba_ports[index] = uap; 2562 2563 return 0; 2564 } 2565 2566 static int pl011_register_port(struct uart_amba_port *uap) 2567 { 2568 int ret; 2569 2570 /* Ensure interrupts from this UART are masked and cleared */ 2571 pl011_write(0, uap, REG_IMSC); 2572 pl011_write(0xffff, uap, REG_ICR); 2573 2574 if (!amba_reg.state) { 2575 ret = uart_register_driver(&amba_reg); 2576 if (ret < 0) { 2577 dev_err(uap->port.dev, 2578 "Failed to register AMBA-PL011 driver\n"); 2579 return ret; 2580 } 2581 } 2582 2583 ret = uart_add_one_port(&amba_reg, &uap->port); 2584 if (ret) 2585 pl011_unregister_port(uap); 2586 2587 return ret; 2588 } 2589 2590 static int pl011_probe(struct amba_device *dev, const struct amba_id *id) 2591 { 2592 struct uart_amba_port *uap; 2593 struct vendor_data *vendor = id->data; 2594 int portnr, ret; 2595 2596 portnr = pl011_find_free_port(); 2597 if (portnr < 0) 2598 return portnr; 2599 2600 uap = devm_kzalloc(&dev->dev, sizeof(struct uart_amba_port), 2601 GFP_KERNEL); 2602 if (!uap) 2603 return -ENOMEM; 2604 2605 uap->clk = devm_clk_get(&dev->dev, NULL); 2606 if (IS_ERR(uap->clk)) 2607 return PTR_ERR(uap->clk); 2608 2609 uap->reg_offset = vendor->reg_offset; 2610 uap->vendor = vendor; 2611 uap->fifosize = vendor->get_fifosize(dev); 2612 uap->port.iotype = vendor->access_32b ? UPIO_MEM32 : UPIO_MEM; 2613 uap->port.irq = dev->irq[0]; 2614 uap->port.ops = &amba_pl011_pops; 2615 2616 snprintf(uap->type, sizeof(uap->type), "PL011 rev%u", amba_rev(dev)); 2617 2618 ret = pl011_setup_port(&dev->dev, uap, &dev->res, portnr); 2619 if (ret) 2620 return ret; 2621 2622 amba_set_drvdata(dev, uap); 2623 2624 return pl011_register_port(uap); 2625 } 2626 2627 static int pl011_remove(struct amba_device *dev) 2628 { 2629 struct uart_amba_port *uap = amba_get_drvdata(dev); 2630 2631 uart_remove_one_port(&amba_reg, &uap->port); 2632 pl011_unregister_port(uap); 2633 return 0; 2634 } 2635 2636 #ifdef CONFIG_PM_SLEEP 2637 static int pl011_suspend(struct device *dev) 2638 { 2639 struct uart_amba_port *uap = dev_get_drvdata(dev); 2640 2641 if (!uap) 2642 return -EINVAL; 2643 2644 return uart_suspend_port(&amba_reg, &uap->port); 2645 } 2646 2647 static int pl011_resume(struct device *dev) 2648 { 2649 struct uart_amba_port *uap = dev_get_drvdata(dev); 2650 2651 if (!uap) 2652 return -EINVAL; 2653 2654 return uart_resume_port(&amba_reg, &uap->port); 2655 } 2656 #endif 2657 2658 static SIMPLE_DEV_PM_OPS(pl011_dev_pm_ops, pl011_suspend, pl011_resume); 2659 2660 static int sbsa_uart_probe(struct platform_device *pdev) 2661 { 2662 struct uart_amba_port *uap; 2663 struct resource *r; 2664 int portnr, ret; 2665 int baudrate; 2666 2667 /* 2668 * Check the mandatory baud rate parameter in the DT node early 2669 * so that we can easily exit with the error. 2670 */ 2671 if (pdev->dev.of_node) { 2672 struct device_node *np = pdev->dev.of_node; 2673 2674 ret = of_property_read_u32(np, "current-speed", &baudrate); 2675 if (ret) 2676 return ret; 2677 } else { 2678 baudrate = 115200; 2679 } 2680 2681 portnr = pl011_find_free_port(); 2682 if (portnr < 0) 2683 return portnr; 2684 2685 uap = devm_kzalloc(&pdev->dev, sizeof(struct uart_amba_port), 2686 GFP_KERNEL); 2687 if (!uap) 2688 return -ENOMEM; 2689 2690 ret = platform_get_irq(pdev, 0); 2691 if (ret < 0) { 2692 if (ret != -EPROBE_DEFER) 2693 dev_err(&pdev->dev, "cannot obtain irq\n"); 2694 return ret; 2695 } 2696 uap->port.irq = ret; 2697 2698 uap->reg_offset = vendor_sbsa.reg_offset; 2699 uap->vendor = qdf2400_e44_present ? 2700 &vendor_qdt_qdf2400_e44 : &vendor_sbsa; 2701 uap->fifosize = 32; 2702 uap->port.iotype = vendor_sbsa.access_32b ? UPIO_MEM32 : UPIO_MEM; 2703 uap->port.ops = &sbsa_uart_pops; 2704 uap->fixed_baud = baudrate; 2705 2706 snprintf(uap->type, sizeof(uap->type), "SBSA"); 2707 2708 r = platform_get_resource(pdev, IORESOURCE_MEM, 0); 2709 2710 ret = pl011_setup_port(&pdev->dev, uap, r, portnr); 2711 if (ret) 2712 return ret; 2713 2714 platform_set_drvdata(pdev, uap); 2715 2716 return pl011_register_port(uap); 2717 } 2718 2719 static int sbsa_uart_remove(struct platform_device *pdev) 2720 { 2721 struct uart_amba_port *uap = platform_get_drvdata(pdev); 2722 2723 uart_remove_one_port(&amba_reg, &uap->port); 2724 pl011_unregister_port(uap); 2725 return 0; 2726 } 2727 2728 static const struct of_device_id sbsa_uart_of_match[] = { 2729 { .compatible = "arm,sbsa-uart", }, 2730 {}, 2731 }; 2732 MODULE_DEVICE_TABLE(of, sbsa_uart_of_match); 2733 2734 static const struct acpi_device_id sbsa_uart_acpi_match[] = { 2735 { "ARMH0011", 0 }, 2736 {}, 2737 }; 2738 MODULE_DEVICE_TABLE(acpi, sbsa_uart_acpi_match); 2739 2740 static struct platform_driver arm_sbsa_uart_platform_driver = { 2741 .probe = sbsa_uart_probe, 2742 .remove = sbsa_uart_remove, 2743 .driver = { 2744 .name = "sbsa-uart", 2745 .of_match_table = of_match_ptr(sbsa_uart_of_match), 2746 .acpi_match_table = ACPI_PTR(sbsa_uart_acpi_match), 2747 }, 2748 }; 2749 2750 static struct amba_id pl011_ids[] = { 2751 { 2752 .id = 0x00041011, 2753 .mask = 0x000fffff, 2754 .data = &vendor_arm, 2755 }, 2756 { 2757 .id = 0x00380802, 2758 .mask = 0x00ffffff, 2759 .data = &vendor_st, 2760 }, 2761 { 2762 .id = AMBA_LINUX_ID(0x00, 0x1, 0xffe), 2763 .mask = 0x00ffffff, 2764 .data = &vendor_zte, 2765 }, 2766 { 0, 0 }, 2767 }; 2768 2769 MODULE_DEVICE_TABLE(amba, pl011_ids); 2770 2771 static struct amba_driver pl011_driver = { 2772 .drv = { 2773 .name = "uart-pl011", 2774 .pm = &pl011_dev_pm_ops, 2775 }, 2776 .id_table = pl011_ids, 2777 .probe = pl011_probe, 2778 .remove = pl011_remove, 2779 }; 2780 2781 static int __init pl011_init(void) 2782 { 2783 printk(KERN_INFO "Serial: AMBA PL011 UART driver\n"); 2784 2785 if (platform_driver_register(&arm_sbsa_uart_platform_driver)) 2786 pr_warn("could not register SBSA UART platform driver\n"); 2787 return amba_driver_register(&pl011_driver); 2788 } 2789 2790 static void __exit pl011_exit(void) 2791 { 2792 platform_driver_unregister(&arm_sbsa_uart_platform_driver); 2793 amba_driver_unregister(&pl011_driver); 2794 } 2795 2796 /* 2797 * While this can be a module, if builtin it's most likely the console 2798 * So let's leave module_exit but move module_init to an earlier place 2799 */ 2800 arch_initcall(pl011_init); 2801 module_exit(pl011_exit); 2802 2803 MODULE_AUTHOR("ARM Ltd/Deep Blue Solutions Ltd"); 2804 MODULE_DESCRIPTION("ARM AMBA serial port driver"); 2805 MODULE_LICENSE("GPL"); 2806