1 // SPDX-License-Identifier: GPL-2.0+ 2 /* 3 * Driver for AMBA serial ports 4 * 5 * Based on drivers/char/serial.c, by Linus Torvalds, Theodore Ts'o. 6 * 7 * Copyright 1999 ARM Limited 8 * Copyright (C) 2000 Deep Blue Solutions Ltd. 9 * 10 * This is a generic driver for ARM AMBA-type serial ports. They 11 * have a lot of 16550-like features, but are not register compatible. 12 * Note that although they do have CTS, DCD and DSR inputs, they do 13 * not have an RI input, nor do they have DTR or RTS outputs. If 14 * required, these have to be supplied via some other means (eg, GPIO) 15 * and hooked into this driver. 16 */ 17 18 #include <linux/module.h> 19 #include <linux/ioport.h> 20 #include <linux/init.h> 21 #include <linux/console.h> 22 #include <linux/sysrq.h> 23 #include <linux/device.h> 24 #include <linux/tty.h> 25 #include <linux/tty_flip.h> 26 #include <linux/serial_core.h> 27 #include <linux/serial.h> 28 #include <linux/amba/bus.h> 29 #include <linux/amba/serial.h> 30 #include <linux/clk.h> 31 #include <linux/slab.h> 32 #include <linux/io.h> 33 34 #define UART_NR 8 35 36 #define SERIAL_AMBA_MAJOR 204 37 #define SERIAL_AMBA_MINOR 16 38 #define SERIAL_AMBA_NR UART_NR 39 40 #define AMBA_ISR_PASS_LIMIT 256 41 42 #define UART_RX_DATA(s) (((s) & UART01x_FR_RXFE) == 0) 43 #define UART_TX_READY(s) (((s) & UART01x_FR_TXFF) == 0) 44 45 #define UART_DUMMY_RSR_RX 256 46 #define UART_PORT_SIZE 64 47 48 /* 49 * We wrap our port structure around the generic uart_port. 50 */ 51 struct uart_amba_port { 52 struct uart_port port; 53 struct clk *clk; 54 struct amba_device *dev; 55 struct amba_pl010_data *data; 56 unsigned int old_status; 57 }; 58 59 static void pl010_stop_tx(struct uart_port *port) 60 { 61 struct uart_amba_port *uap = 62 container_of(port, struct uart_amba_port, port); 63 unsigned int cr; 64 65 cr = readb(uap->port.membase + UART010_CR); 66 cr &= ~UART010_CR_TIE; 67 writel(cr, uap->port.membase + UART010_CR); 68 } 69 70 static void pl010_start_tx(struct uart_port *port) 71 { 72 struct uart_amba_port *uap = 73 container_of(port, struct uart_amba_port, port); 74 unsigned int cr; 75 76 cr = readb(uap->port.membase + UART010_CR); 77 cr |= UART010_CR_TIE; 78 writel(cr, uap->port.membase + UART010_CR); 79 } 80 81 static void pl010_stop_rx(struct uart_port *port) 82 { 83 struct uart_amba_port *uap = 84 container_of(port, struct uart_amba_port, port); 85 unsigned int cr; 86 87 cr = readb(uap->port.membase + UART010_CR); 88 cr &= ~(UART010_CR_RIE | UART010_CR_RTIE); 89 writel(cr, uap->port.membase + UART010_CR); 90 } 91 92 static void pl010_disable_ms(struct uart_port *port) 93 { 94 struct uart_amba_port *uap = (struct uart_amba_port *)port; 95 unsigned int cr; 96 97 cr = readb(uap->port.membase + UART010_CR); 98 cr &= ~UART010_CR_MSIE; 99 writel(cr, uap->port.membase + UART010_CR); 100 } 101 102 static void pl010_enable_ms(struct uart_port *port) 103 { 104 struct uart_amba_port *uap = 105 container_of(port, struct uart_amba_port, port); 106 unsigned int cr; 107 108 cr = readb(uap->port.membase + UART010_CR); 109 cr |= UART010_CR_MSIE; 110 writel(cr, uap->port.membase + UART010_CR); 111 } 112 113 static void pl010_rx_chars(struct uart_amba_port *uap) 114 { 115 unsigned int status, ch, flag, rsr, max_count = 256; 116 117 status = readb(uap->port.membase + UART01x_FR); 118 while (UART_RX_DATA(status) && max_count--) { 119 ch = readb(uap->port.membase + UART01x_DR); 120 flag = TTY_NORMAL; 121 122 uap->port.icount.rx++; 123 124 /* 125 * Note that the error handling code is 126 * out of the main execution path 127 */ 128 rsr = readb(uap->port.membase + UART01x_RSR) | UART_DUMMY_RSR_RX; 129 if (unlikely(rsr & UART01x_RSR_ANY)) { 130 writel(0, uap->port.membase + UART01x_ECR); 131 132 if (rsr & UART01x_RSR_BE) { 133 rsr &= ~(UART01x_RSR_FE | UART01x_RSR_PE); 134 uap->port.icount.brk++; 135 if (uart_handle_break(&uap->port)) 136 goto ignore_char; 137 } else if (rsr & UART01x_RSR_PE) 138 uap->port.icount.parity++; 139 else if (rsr & UART01x_RSR_FE) 140 uap->port.icount.frame++; 141 if (rsr & UART01x_RSR_OE) 142 uap->port.icount.overrun++; 143 144 rsr &= uap->port.read_status_mask; 145 146 if (rsr & UART01x_RSR_BE) 147 flag = TTY_BREAK; 148 else if (rsr & UART01x_RSR_PE) 149 flag = TTY_PARITY; 150 else if (rsr & UART01x_RSR_FE) 151 flag = TTY_FRAME; 152 } 153 154 if (uart_handle_sysrq_char(&uap->port, ch)) 155 goto ignore_char; 156 157 uart_insert_char(&uap->port, rsr, UART01x_RSR_OE, ch, flag); 158 159 ignore_char: 160 status = readb(uap->port.membase + UART01x_FR); 161 } 162 spin_unlock(&uap->port.lock); 163 tty_flip_buffer_push(&uap->port.state->port); 164 spin_lock(&uap->port.lock); 165 } 166 167 static void pl010_tx_chars(struct uart_amba_port *uap) 168 { 169 struct circ_buf *xmit = &uap->port.state->xmit; 170 int count; 171 172 if (uap->port.x_char) { 173 writel(uap->port.x_char, uap->port.membase + UART01x_DR); 174 uap->port.icount.tx++; 175 uap->port.x_char = 0; 176 return; 177 } 178 if (uart_circ_empty(xmit) || uart_tx_stopped(&uap->port)) { 179 pl010_stop_tx(&uap->port); 180 return; 181 } 182 183 count = uap->port.fifosize >> 1; 184 do { 185 writel(xmit->buf[xmit->tail], uap->port.membase + UART01x_DR); 186 xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1); 187 uap->port.icount.tx++; 188 if (uart_circ_empty(xmit)) 189 break; 190 } while (--count > 0); 191 192 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) 193 uart_write_wakeup(&uap->port); 194 195 if (uart_circ_empty(xmit)) 196 pl010_stop_tx(&uap->port); 197 } 198 199 static void pl010_modem_status(struct uart_amba_port *uap) 200 { 201 unsigned int status, delta; 202 203 writel(0, uap->port.membase + UART010_ICR); 204 205 status = readb(uap->port.membase + UART01x_FR) & UART01x_FR_MODEM_ANY; 206 207 delta = status ^ uap->old_status; 208 uap->old_status = status; 209 210 if (!delta) 211 return; 212 213 if (delta & UART01x_FR_DCD) 214 uart_handle_dcd_change(&uap->port, status & UART01x_FR_DCD); 215 216 if (delta & UART01x_FR_DSR) 217 uap->port.icount.dsr++; 218 219 if (delta & UART01x_FR_CTS) 220 uart_handle_cts_change(&uap->port, status & UART01x_FR_CTS); 221 222 wake_up_interruptible(&uap->port.state->port.delta_msr_wait); 223 } 224 225 static irqreturn_t pl010_int(int irq, void *dev_id) 226 { 227 struct uart_amba_port *uap = dev_id; 228 unsigned int status, pass_counter = AMBA_ISR_PASS_LIMIT; 229 int handled = 0; 230 231 spin_lock(&uap->port.lock); 232 233 status = readb(uap->port.membase + UART010_IIR); 234 if (status) { 235 do { 236 if (status & (UART010_IIR_RTIS | UART010_IIR_RIS)) 237 pl010_rx_chars(uap); 238 if (status & UART010_IIR_MIS) 239 pl010_modem_status(uap); 240 if (status & UART010_IIR_TIS) 241 pl010_tx_chars(uap); 242 243 if (pass_counter-- == 0) 244 break; 245 246 status = readb(uap->port.membase + UART010_IIR); 247 } while (status & (UART010_IIR_RTIS | UART010_IIR_RIS | 248 UART010_IIR_TIS)); 249 handled = 1; 250 } 251 252 spin_unlock(&uap->port.lock); 253 254 return IRQ_RETVAL(handled); 255 } 256 257 static unsigned int pl010_tx_empty(struct uart_port *port) 258 { 259 struct uart_amba_port *uap = 260 container_of(port, struct uart_amba_port, port); 261 unsigned int status = readb(uap->port.membase + UART01x_FR); 262 return status & UART01x_FR_BUSY ? 0 : TIOCSER_TEMT; 263 } 264 265 static unsigned int pl010_get_mctrl(struct uart_port *port) 266 { 267 struct uart_amba_port *uap = 268 container_of(port, struct uart_amba_port, port); 269 unsigned int result = 0; 270 unsigned int status; 271 272 status = readb(uap->port.membase + UART01x_FR); 273 if (status & UART01x_FR_DCD) 274 result |= TIOCM_CAR; 275 if (status & UART01x_FR_DSR) 276 result |= TIOCM_DSR; 277 if (status & UART01x_FR_CTS) 278 result |= TIOCM_CTS; 279 280 return result; 281 } 282 283 static void pl010_set_mctrl(struct uart_port *port, unsigned int mctrl) 284 { 285 struct uart_amba_port *uap = 286 container_of(port, struct uart_amba_port, port); 287 288 if (uap->data) 289 uap->data->set_mctrl(uap->dev, uap->port.membase, mctrl); 290 } 291 292 static void pl010_break_ctl(struct uart_port *port, int break_state) 293 { 294 struct uart_amba_port *uap = 295 container_of(port, struct uart_amba_port, port); 296 unsigned long flags; 297 unsigned int lcr_h; 298 299 spin_lock_irqsave(&uap->port.lock, flags); 300 lcr_h = readb(uap->port.membase + UART010_LCRH); 301 if (break_state == -1) 302 lcr_h |= UART01x_LCRH_BRK; 303 else 304 lcr_h &= ~UART01x_LCRH_BRK; 305 writel(lcr_h, uap->port.membase + UART010_LCRH); 306 spin_unlock_irqrestore(&uap->port.lock, flags); 307 } 308 309 static int pl010_startup(struct uart_port *port) 310 { 311 struct uart_amba_port *uap = 312 container_of(port, struct uart_amba_port, port); 313 int retval; 314 315 /* 316 * Try to enable the clock producer. 317 */ 318 retval = clk_prepare_enable(uap->clk); 319 if (retval) 320 goto out; 321 322 uap->port.uartclk = clk_get_rate(uap->clk); 323 324 /* 325 * Allocate the IRQ 326 */ 327 retval = request_irq(uap->port.irq, pl010_int, 0, "uart-pl010", uap); 328 if (retval) 329 goto clk_dis; 330 331 /* 332 * initialise the old status of the modem signals 333 */ 334 uap->old_status = readb(uap->port.membase + UART01x_FR) & UART01x_FR_MODEM_ANY; 335 336 /* 337 * Finally, enable interrupts 338 */ 339 writel(UART01x_CR_UARTEN | UART010_CR_RIE | UART010_CR_RTIE, 340 uap->port.membase + UART010_CR); 341 342 return 0; 343 344 clk_dis: 345 clk_disable_unprepare(uap->clk); 346 out: 347 return retval; 348 } 349 350 static void pl010_shutdown(struct uart_port *port) 351 { 352 struct uart_amba_port *uap = 353 container_of(port, struct uart_amba_port, port); 354 355 /* 356 * Free the interrupt 357 */ 358 free_irq(uap->port.irq, uap); 359 360 /* 361 * disable all interrupts, disable the port 362 */ 363 writel(0, uap->port.membase + UART010_CR); 364 365 /* disable break condition and fifos */ 366 writel(readb(uap->port.membase + UART010_LCRH) & 367 ~(UART01x_LCRH_BRK | UART01x_LCRH_FEN), 368 uap->port.membase + UART010_LCRH); 369 370 /* 371 * Shut down the clock producer 372 */ 373 clk_disable_unprepare(uap->clk); 374 } 375 376 static void 377 pl010_set_termios(struct uart_port *port, struct ktermios *termios, 378 struct ktermios *old) 379 { 380 struct uart_amba_port *uap = 381 container_of(port, struct uart_amba_port, port); 382 unsigned int lcr_h, old_cr; 383 unsigned long flags; 384 unsigned int baud, quot; 385 386 /* 387 * Ask the core to calculate the divisor for us. 388 */ 389 baud = uart_get_baud_rate(port, termios, old, 0, uap->port.uartclk/16); 390 quot = uart_get_divisor(port, baud); 391 392 switch (termios->c_cflag & CSIZE) { 393 case CS5: 394 lcr_h = UART01x_LCRH_WLEN_5; 395 break; 396 case CS6: 397 lcr_h = UART01x_LCRH_WLEN_6; 398 break; 399 case CS7: 400 lcr_h = UART01x_LCRH_WLEN_7; 401 break; 402 default: // CS8 403 lcr_h = UART01x_LCRH_WLEN_8; 404 break; 405 } 406 if (termios->c_cflag & CSTOPB) 407 lcr_h |= UART01x_LCRH_STP2; 408 if (termios->c_cflag & PARENB) { 409 lcr_h |= UART01x_LCRH_PEN; 410 if (!(termios->c_cflag & PARODD)) 411 lcr_h |= UART01x_LCRH_EPS; 412 } 413 if (uap->port.fifosize > 1) 414 lcr_h |= UART01x_LCRH_FEN; 415 416 spin_lock_irqsave(&uap->port.lock, flags); 417 418 /* 419 * Update the per-port timeout. 420 */ 421 uart_update_timeout(port, termios->c_cflag, baud); 422 423 uap->port.read_status_mask = UART01x_RSR_OE; 424 if (termios->c_iflag & INPCK) 425 uap->port.read_status_mask |= UART01x_RSR_FE | UART01x_RSR_PE; 426 if (termios->c_iflag & (IGNBRK | BRKINT | PARMRK)) 427 uap->port.read_status_mask |= UART01x_RSR_BE; 428 429 /* 430 * Characters to ignore 431 */ 432 uap->port.ignore_status_mask = 0; 433 if (termios->c_iflag & IGNPAR) 434 uap->port.ignore_status_mask |= UART01x_RSR_FE | UART01x_RSR_PE; 435 if (termios->c_iflag & IGNBRK) { 436 uap->port.ignore_status_mask |= UART01x_RSR_BE; 437 /* 438 * If we're ignoring parity and break indicators, 439 * ignore overruns too (for real raw support). 440 */ 441 if (termios->c_iflag & IGNPAR) 442 uap->port.ignore_status_mask |= UART01x_RSR_OE; 443 } 444 445 /* 446 * Ignore all characters if CREAD is not set. 447 */ 448 if ((termios->c_cflag & CREAD) == 0) 449 uap->port.ignore_status_mask |= UART_DUMMY_RSR_RX; 450 451 /* first, disable everything */ 452 old_cr = readb(uap->port.membase + UART010_CR) & ~UART010_CR_MSIE; 453 454 if (UART_ENABLE_MS(port, termios->c_cflag)) 455 old_cr |= UART010_CR_MSIE; 456 457 writel(0, uap->port.membase + UART010_CR); 458 459 /* Set baud rate */ 460 quot -= 1; 461 writel((quot & 0xf00) >> 8, uap->port.membase + UART010_LCRM); 462 writel(quot & 0xff, uap->port.membase + UART010_LCRL); 463 464 /* 465 * ----------v----------v----------v----------v----- 466 * NOTE: MUST BE WRITTEN AFTER UARTLCR_M & UARTLCR_L 467 * ----------^----------^----------^----------^----- 468 */ 469 writel(lcr_h, uap->port.membase + UART010_LCRH); 470 writel(old_cr, uap->port.membase + UART010_CR); 471 472 spin_unlock_irqrestore(&uap->port.lock, flags); 473 } 474 475 static void pl010_set_ldisc(struct uart_port *port, struct ktermios *termios) 476 { 477 if (termios->c_line == N_PPS) { 478 port->flags |= UPF_HARDPPS_CD; 479 spin_lock_irq(&port->lock); 480 pl010_enable_ms(port); 481 spin_unlock_irq(&port->lock); 482 } else { 483 port->flags &= ~UPF_HARDPPS_CD; 484 if (!UART_ENABLE_MS(port, termios->c_cflag)) { 485 spin_lock_irq(&port->lock); 486 pl010_disable_ms(port); 487 spin_unlock_irq(&port->lock); 488 } 489 } 490 } 491 492 static const char *pl010_type(struct uart_port *port) 493 { 494 return port->type == PORT_AMBA ? "AMBA" : NULL; 495 } 496 497 /* 498 * Release the memory region(s) being used by 'port' 499 */ 500 static void pl010_release_port(struct uart_port *port) 501 { 502 release_mem_region(port->mapbase, UART_PORT_SIZE); 503 } 504 505 /* 506 * Request the memory region(s) being used by 'port' 507 */ 508 static int pl010_request_port(struct uart_port *port) 509 { 510 return request_mem_region(port->mapbase, UART_PORT_SIZE, "uart-pl010") 511 != NULL ? 0 : -EBUSY; 512 } 513 514 /* 515 * Configure/autoconfigure the port. 516 */ 517 static void pl010_config_port(struct uart_port *port, int flags) 518 { 519 if (flags & UART_CONFIG_TYPE) { 520 port->type = PORT_AMBA; 521 pl010_request_port(port); 522 } 523 } 524 525 /* 526 * verify the new serial_struct (for TIOCSSERIAL). 527 */ 528 static int pl010_verify_port(struct uart_port *port, struct serial_struct *ser) 529 { 530 int ret = 0; 531 if (ser->type != PORT_UNKNOWN && ser->type != PORT_AMBA) 532 ret = -EINVAL; 533 if (ser->irq < 0 || ser->irq >= nr_irqs) 534 ret = -EINVAL; 535 if (ser->baud_base < 9600) 536 ret = -EINVAL; 537 return ret; 538 } 539 540 static const struct uart_ops amba_pl010_pops = { 541 .tx_empty = pl010_tx_empty, 542 .set_mctrl = pl010_set_mctrl, 543 .get_mctrl = pl010_get_mctrl, 544 .stop_tx = pl010_stop_tx, 545 .start_tx = pl010_start_tx, 546 .stop_rx = pl010_stop_rx, 547 .enable_ms = pl010_enable_ms, 548 .break_ctl = pl010_break_ctl, 549 .startup = pl010_startup, 550 .shutdown = pl010_shutdown, 551 .set_termios = pl010_set_termios, 552 .set_ldisc = pl010_set_ldisc, 553 .type = pl010_type, 554 .release_port = pl010_release_port, 555 .request_port = pl010_request_port, 556 .config_port = pl010_config_port, 557 .verify_port = pl010_verify_port, 558 }; 559 560 static struct uart_amba_port *amba_ports[UART_NR]; 561 562 #ifdef CONFIG_SERIAL_AMBA_PL010_CONSOLE 563 564 static void pl010_console_putchar(struct uart_port *port, int ch) 565 { 566 struct uart_amba_port *uap = 567 container_of(port, struct uart_amba_port, port); 568 unsigned int status; 569 570 do { 571 status = readb(uap->port.membase + UART01x_FR); 572 barrier(); 573 } while (!UART_TX_READY(status)); 574 writel(ch, uap->port.membase + UART01x_DR); 575 } 576 577 static void 578 pl010_console_write(struct console *co, const char *s, unsigned int count) 579 { 580 struct uart_amba_port *uap = amba_ports[co->index]; 581 unsigned int status, old_cr; 582 583 clk_enable(uap->clk); 584 585 /* 586 * First save the CR then disable the interrupts 587 */ 588 old_cr = readb(uap->port.membase + UART010_CR); 589 writel(UART01x_CR_UARTEN, uap->port.membase + UART010_CR); 590 591 uart_console_write(&uap->port, s, count, pl010_console_putchar); 592 593 /* 594 * Finally, wait for transmitter to become empty 595 * and restore the TCR 596 */ 597 do { 598 status = readb(uap->port.membase + UART01x_FR); 599 barrier(); 600 } while (status & UART01x_FR_BUSY); 601 writel(old_cr, uap->port.membase + UART010_CR); 602 603 clk_disable(uap->clk); 604 } 605 606 static void __init 607 pl010_console_get_options(struct uart_amba_port *uap, int *baud, 608 int *parity, int *bits) 609 { 610 if (readb(uap->port.membase + UART010_CR) & UART01x_CR_UARTEN) { 611 unsigned int lcr_h, quot; 612 lcr_h = readb(uap->port.membase + UART010_LCRH); 613 614 *parity = 'n'; 615 if (lcr_h & UART01x_LCRH_PEN) { 616 if (lcr_h & UART01x_LCRH_EPS) 617 *parity = 'e'; 618 else 619 *parity = 'o'; 620 } 621 622 if ((lcr_h & 0x60) == UART01x_LCRH_WLEN_7) 623 *bits = 7; 624 else 625 *bits = 8; 626 627 quot = readb(uap->port.membase + UART010_LCRL) | 628 readb(uap->port.membase + UART010_LCRM) << 8; 629 *baud = uap->port.uartclk / (16 * (quot + 1)); 630 } 631 } 632 633 static int __init pl010_console_setup(struct console *co, char *options) 634 { 635 struct uart_amba_port *uap; 636 int baud = 38400; 637 int bits = 8; 638 int parity = 'n'; 639 int flow = 'n'; 640 int ret; 641 642 /* 643 * Check whether an invalid uart number has been specified, and 644 * if so, search for the first available port that does have 645 * console support. 646 */ 647 if (co->index >= UART_NR) 648 co->index = 0; 649 uap = amba_ports[co->index]; 650 if (!uap) 651 return -ENODEV; 652 653 ret = clk_prepare(uap->clk); 654 if (ret) 655 return ret; 656 657 uap->port.uartclk = clk_get_rate(uap->clk); 658 659 if (options) 660 uart_parse_options(options, &baud, &parity, &bits, &flow); 661 else 662 pl010_console_get_options(uap, &baud, &parity, &bits); 663 664 return uart_set_options(&uap->port, co, baud, parity, bits, flow); 665 } 666 667 static struct uart_driver amba_reg; 668 static struct console amba_console = { 669 .name = "ttyAM", 670 .write = pl010_console_write, 671 .device = uart_console_device, 672 .setup = pl010_console_setup, 673 .flags = CON_PRINTBUFFER, 674 .index = -1, 675 .data = &amba_reg, 676 }; 677 678 #define AMBA_CONSOLE &amba_console 679 #else 680 #define AMBA_CONSOLE NULL 681 #endif 682 683 static DEFINE_MUTEX(amba_reg_lock); 684 static struct uart_driver amba_reg = { 685 .owner = THIS_MODULE, 686 .driver_name = "ttyAM", 687 .dev_name = "ttyAM", 688 .major = SERIAL_AMBA_MAJOR, 689 .minor = SERIAL_AMBA_MINOR, 690 .nr = UART_NR, 691 .cons = AMBA_CONSOLE, 692 }; 693 694 static int pl010_probe(struct amba_device *dev, const struct amba_id *id) 695 { 696 struct uart_amba_port *uap; 697 void __iomem *base; 698 int i, ret; 699 700 for (i = 0; i < ARRAY_SIZE(amba_ports); i++) 701 if (amba_ports[i] == NULL) 702 break; 703 704 if (i == ARRAY_SIZE(amba_ports)) 705 return -EBUSY; 706 707 uap = devm_kzalloc(&dev->dev, sizeof(struct uart_amba_port), 708 GFP_KERNEL); 709 if (!uap) 710 return -ENOMEM; 711 712 base = devm_ioremap(&dev->dev, dev->res.start, 713 resource_size(&dev->res)); 714 if (!base) 715 return -ENOMEM; 716 717 uap->clk = devm_clk_get(&dev->dev, NULL); 718 if (IS_ERR(uap->clk)) 719 return PTR_ERR(uap->clk); 720 721 uap->port.dev = &dev->dev; 722 uap->port.mapbase = dev->res.start; 723 uap->port.membase = base; 724 uap->port.iotype = UPIO_MEM; 725 uap->port.irq = dev->irq[0]; 726 uap->port.fifosize = 16; 727 uap->port.has_sysrq = IS_ENABLED(CONFIG_SERIAL_AMBA_PL010_CONSOLE); 728 uap->port.ops = &amba_pl010_pops; 729 uap->port.flags = UPF_BOOT_AUTOCONF; 730 uap->port.line = i; 731 uap->dev = dev; 732 uap->data = dev_get_platdata(&dev->dev); 733 734 amba_ports[i] = uap; 735 736 amba_set_drvdata(dev, uap); 737 738 mutex_lock(&amba_reg_lock); 739 if (!amba_reg.state) { 740 ret = uart_register_driver(&amba_reg); 741 if (ret < 0) { 742 mutex_unlock(&amba_reg_lock); 743 dev_err(uap->port.dev, 744 "Failed to register AMBA-PL010 driver\n"); 745 return ret; 746 } 747 } 748 mutex_unlock(&amba_reg_lock); 749 750 ret = uart_add_one_port(&amba_reg, &uap->port); 751 if (ret) 752 amba_ports[i] = NULL; 753 754 return ret; 755 } 756 757 static int pl010_remove(struct amba_device *dev) 758 { 759 struct uart_amba_port *uap = amba_get_drvdata(dev); 760 int i; 761 bool busy = false; 762 763 uart_remove_one_port(&amba_reg, &uap->port); 764 765 for (i = 0; i < ARRAY_SIZE(amba_ports); i++) 766 if (amba_ports[i] == uap) 767 amba_ports[i] = NULL; 768 else if (amba_ports[i]) 769 busy = true; 770 771 if (!busy) 772 uart_unregister_driver(&amba_reg); 773 774 return 0; 775 } 776 777 #ifdef CONFIG_PM_SLEEP 778 static int pl010_suspend(struct device *dev) 779 { 780 struct uart_amba_port *uap = dev_get_drvdata(dev); 781 782 if (uap) 783 uart_suspend_port(&amba_reg, &uap->port); 784 785 return 0; 786 } 787 788 static int pl010_resume(struct device *dev) 789 { 790 struct uart_amba_port *uap = dev_get_drvdata(dev); 791 792 if (uap) 793 uart_resume_port(&amba_reg, &uap->port); 794 795 return 0; 796 } 797 #endif 798 799 static SIMPLE_DEV_PM_OPS(pl010_dev_pm_ops, pl010_suspend, pl010_resume); 800 801 static const struct amba_id pl010_ids[] = { 802 { 803 .id = 0x00041010, 804 .mask = 0x000fffff, 805 }, 806 { 0, 0 }, 807 }; 808 809 MODULE_DEVICE_TABLE(amba, pl010_ids); 810 811 static struct amba_driver pl010_driver = { 812 .drv = { 813 .name = "uart-pl010", 814 .pm = &pl010_dev_pm_ops, 815 }, 816 .id_table = pl010_ids, 817 .probe = pl010_probe, 818 .remove = pl010_remove, 819 }; 820 821 static int __init pl010_init(void) 822 { 823 printk(KERN_INFO "Serial: AMBA driver\n"); 824 825 return amba_driver_register(&pl010_driver); 826 } 827 828 static void __exit pl010_exit(void) 829 { 830 amba_driver_unregister(&pl010_driver); 831 } 832 833 module_init(pl010_init); 834 module_exit(pl010_exit); 835 836 MODULE_AUTHOR("ARM Ltd/Deep Blue Solutions Ltd"); 837 MODULE_DESCRIPTION("ARM AMBA serial port driver"); 838 MODULE_LICENSE("GPL"); 839