1 // SPDX-License-Identifier: GPL-2.0+ 2 /* 3 * Serial Port driver for Open Firmware platform devices 4 * 5 * Copyright (C) 2006 Arnd Bergmann <arnd@arndb.de>, IBM Corp. 6 */ 7 #include <linux/console.h> 8 #include <linux/module.h> 9 #include <linux/slab.h> 10 #include <linux/serial_core.h> 11 #include <linux/serial_reg.h> 12 #include <linux/of_address.h> 13 #include <linux/of_irq.h> 14 #include <linux/of_platform.h> 15 #include <linux/pm_runtime.h> 16 #include <linux/clk.h> 17 #include <linux/reset.h> 18 19 #include "8250.h" 20 21 struct of_serial_info { 22 struct clk *clk; 23 struct reset_control *rst; 24 int type; 25 int line; 26 }; 27 28 /* 29 * Fill a struct uart_port for a given device node 30 */ 31 static int of_platform_serial_setup(struct platform_device *ofdev, 32 int type, struct uart_8250_port *up, 33 struct of_serial_info *info) 34 { 35 struct resource resource; 36 struct device_node *np = ofdev->dev.of_node; 37 struct uart_port *port = &up->port; 38 u32 clk, spd, prop; 39 int ret, irq; 40 41 memset(port, 0, sizeof *port); 42 43 pm_runtime_enable(&ofdev->dev); 44 pm_runtime_get_sync(&ofdev->dev); 45 46 if (of_property_read_u32(np, "clock-frequency", &clk)) { 47 48 /* Get clk rate through clk driver if present */ 49 info->clk = devm_clk_get(&ofdev->dev, NULL); 50 if (IS_ERR(info->clk)) { 51 ret = PTR_ERR(info->clk); 52 if (ret != -EPROBE_DEFER) 53 dev_warn(&ofdev->dev, 54 "failed to get clock: %d\n", ret); 55 goto err_pmruntime; 56 } 57 58 ret = clk_prepare_enable(info->clk); 59 if (ret < 0) 60 goto err_pmruntime; 61 62 clk = clk_get_rate(info->clk); 63 } 64 /* If current-speed was set, then try not to change it. */ 65 if (of_property_read_u32(np, "current-speed", &spd) == 0) 66 port->custom_divisor = clk / (16 * spd); 67 68 ret = of_address_to_resource(np, 0, &resource); 69 if (ret) { 70 dev_warn(&ofdev->dev, "invalid address\n"); 71 goto err_unprepare; 72 } 73 74 port->flags = UPF_SHARE_IRQ | UPF_BOOT_AUTOCONF | UPF_FIXED_PORT | 75 UPF_FIXED_TYPE; 76 spin_lock_init(&port->lock); 77 78 if (resource_type(&resource) == IORESOURCE_IO) { 79 port->iotype = UPIO_PORT; 80 port->iobase = resource.start; 81 } else { 82 port->mapbase = resource.start; 83 port->mapsize = resource_size(&resource); 84 85 /* Check for shifted address mapping */ 86 if (of_property_read_u32(np, "reg-offset", &prop) == 0) 87 port->mapbase += prop; 88 89 port->iotype = UPIO_MEM; 90 if (of_property_read_u32(np, "reg-io-width", &prop) == 0) { 91 switch (prop) { 92 case 1: 93 port->iotype = UPIO_MEM; 94 break; 95 case 2: 96 port->iotype = UPIO_MEM16; 97 break; 98 case 4: 99 port->iotype = of_device_is_big_endian(np) ? 100 UPIO_MEM32BE : UPIO_MEM32; 101 break; 102 default: 103 dev_warn(&ofdev->dev, "unsupported reg-io-width (%d)\n", 104 prop); 105 ret = -EINVAL; 106 goto err_unprepare; 107 } 108 } 109 port->flags |= UPF_IOREMAP; 110 } 111 112 /* Compatibility with the deprecated pxa driver and 8250_pxa drivers. */ 113 if (of_device_is_compatible(np, "mrvl,mmp-uart")) 114 port->regshift = 2; 115 116 /* Check for registers offset within the devices address range */ 117 if (of_property_read_u32(np, "reg-shift", &prop) == 0) 118 port->regshift = prop; 119 120 /* Check for fifo size */ 121 if (of_property_read_u32(np, "fifo-size", &prop) == 0) 122 port->fifosize = prop; 123 124 /* Check for a fixed line number */ 125 ret = of_alias_get_id(np, "serial"); 126 if (ret >= 0) 127 port->line = ret; 128 129 irq = of_irq_get(np, 0); 130 if (irq < 0) { 131 if (irq == -EPROBE_DEFER) { 132 ret = -EPROBE_DEFER; 133 goto err_unprepare; 134 } 135 /* IRQ support not mandatory */ 136 irq = 0; 137 } 138 139 port->irq = irq; 140 141 info->rst = devm_reset_control_get_optional_shared(&ofdev->dev, NULL); 142 if (IS_ERR(info->rst)) { 143 ret = PTR_ERR(info->rst); 144 goto err_unprepare; 145 } 146 147 ret = reset_control_deassert(info->rst); 148 if (ret) 149 goto err_unprepare; 150 151 port->type = type; 152 port->uartclk = clk; 153 154 if (of_property_read_bool(np, "no-loopback-test")) 155 port->flags |= UPF_SKIP_TEST; 156 157 port->dev = &ofdev->dev; 158 port->rs485_config = serial8250_em485_config; 159 up->rs485_start_tx = serial8250_em485_start_tx; 160 up->rs485_stop_tx = serial8250_em485_stop_tx; 161 162 switch (type) { 163 case PORT_RT2880: 164 port->iotype = UPIO_AU; 165 break; 166 } 167 168 if (IS_ENABLED(CONFIG_SERIAL_8250_FSL) && 169 (of_device_is_compatible(np, "fsl,ns16550") || 170 of_device_is_compatible(np, "fsl,16550-FIFO64"))) { 171 port->handle_irq = fsl8250_handle_irq; 172 port->has_sysrq = IS_ENABLED(CONFIG_SERIAL_8250_CONSOLE); 173 } 174 175 return 0; 176 err_unprepare: 177 clk_disable_unprepare(info->clk); 178 err_pmruntime: 179 pm_runtime_put_sync(&ofdev->dev); 180 pm_runtime_disable(&ofdev->dev); 181 return ret; 182 } 183 184 /* 185 * Try to register a serial port 186 */ 187 static int of_platform_serial_probe(struct platform_device *ofdev) 188 { 189 struct of_serial_info *info; 190 struct uart_8250_port port8250; 191 unsigned int port_type; 192 u32 tx_threshold; 193 int ret; 194 195 if (IS_ENABLED(CONFIG_SERIAL_8250_BCM7271) && 196 of_device_is_compatible(ofdev->dev.of_node, "brcm,bcm7271-uart")) 197 return -ENODEV; 198 199 port_type = (unsigned long)of_device_get_match_data(&ofdev->dev); 200 if (port_type == PORT_UNKNOWN) 201 return -EINVAL; 202 203 if (of_property_read_bool(ofdev->dev.of_node, "used-by-rtas")) 204 return -EBUSY; 205 206 info = kzalloc(sizeof(*info), GFP_KERNEL); 207 if (info == NULL) 208 return -ENOMEM; 209 210 memset(&port8250, 0, sizeof(port8250)); 211 ret = of_platform_serial_setup(ofdev, port_type, &port8250, info); 212 if (ret) 213 goto err_free; 214 215 if (port8250.port.fifosize) 216 port8250.capabilities = UART_CAP_FIFO; 217 218 /* Check for TX FIFO threshold & set tx_loadsz */ 219 if ((of_property_read_u32(ofdev->dev.of_node, "tx-threshold", 220 &tx_threshold) == 0) && 221 (tx_threshold < port8250.port.fifosize)) 222 port8250.tx_loadsz = port8250.port.fifosize - tx_threshold; 223 224 if (of_property_read_bool(ofdev->dev.of_node, "auto-flow-control")) 225 port8250.capabilities |= UART_CAP_AFE; 226 227 if (of_property_read_u32(ofdev->dev.of_node, 228 "overrun-throttle-ms", 229 &port8250.overrun_backoff_time_ms) != 0) 230 port8250.overrun_backoff_time_ms = 0; 231 232 ret = serial8250_register_8250_port(&port8250); 233 if (ret < 0) 234 goto err_dispose; 235 236 info->type = port_type; 237 info->line = ret; 238 platform_set_drvdata(ofdev, info); 239 return 0; 240 err_dispose: 241 irq_dispose_mapping(port8250.port.irq); 242 pm_runtime_put_sync(&ofdev->dev); 243 pm_runtime_disable(&ofdev->dev); 244 clk_disable_unprepare(info->clk); 245 err_free: 246 kfree(info); 247 return ret; 248 } 249 250 /* 251 * Release a line 252 */ 253 static int of_platform_serial_remove(struct platform_device *ofdev) 254 { 255 struct of_serial_info *info = platform_get_drvdata(ofdev); 256 257 serial8250_unregister_port(info->line); 258 259 reset_control_assert(info->rst); 260 pm_runtime_put_sync(&ofdev->dev); 261 pm_runtime_disable(&ofdev->dev); 262 clk_disable_unprepare(info->clk); 263 kfree(info); 264 return 0; 265 } 266 267 #ifdef CONFIG_PM_SLEEP 268 static int of_serial_suspend(struct device *dev) 269 { 270 struct of_serial_info *info = dev_get_drvdata(dev); 271 struct uart_8250_port *port8250 = serial8250_get_port(info->line); 272 struct uart_port *port = &port8250->port; 273 274 serial8250_suspend_port(info->line); 275 276 if (!uart_console(port) || console_suspend_enabled) { 277 pm_runtime_put_sync(dev); 278 clk_disable_unprepare(info->clk); 279 } 280 return 0; 281 } 282 283 static int of_serial_resume(struct device *dev) 284 { 285 struct of_serial_info *info = dev_get_drvdata(dev); 286 struct uart_8250_port *port8250 = serial8250_get_port(info->line); 287 struct uart_port *port = &port8250->port; 288 289 if (!uart_console(port) || console_suspend_enabled) { 290 pm_runtime_get_sync(dev); 291 clk_prepare_enable(info->clk); 292 } 293 294 serial8250_resume_port(info->line); 295 296 return 0; 297 } 298 #endif 299 static SIMPLE_DEV_PM_OPS(of_serial_pm_ops, of_serial_suspend, of_serial_resume); 300 301 /* 302 * A few common types, add more as needed. 303 */ 304 static const struct of_device_id of_platform_serial_table[] = { 305 { .compatible = "ns8250", .data = (void *)PORT_8250, }, 306 { .compatible = "ns16450", .data = (void *)PORT_16450, }, 307 { .compatible = "ns16550a", .data = (void *)PORT_16550A, }, 308 { .compatible = "ns16550", .data = (void *)PORT_16550, }, 309 { .compatible = "ns16750", .data = (void *)PORT_16750, }, 310 { .compatible = "ns16850", .data = (void *)PORT_16850, }, 311 { .compatible = "nxp,lpc3220-uart", .data = (void *)PORT_LPC3220, }, 312 { .compatible = "ralink,rt2880-uart", .data = (void *)PORT_RT2880, }, 313 { .compatible = "intel,xscale-uart", .data = (void *)PORT_XSCALE, }, 314 { .compatible = "altr,16550-FIFO32", 315 .data = (void *)PORT_ALTR_16550_F32, }, 316 { .compatible = "altr,16550-FIFO64", 317 .data = (void *)PORT_ALTR_16550_F64, }, 318 { .compatible = "altr,16550-FIFO128", 319 .data = (void *)PORT_ALTR_16550_F128, }, 320 { .compatible = "mediatek,mtk-btif", 321 .data = (void *)PORT_MTK_BTIF, }, 322 { .compatible = "mrvl,mmp-uart", 323 .data = (void *)PORT_XSCALE, }, 324 { .compatible = "ti,da830-uart", .data = (void *)PORT_DA830, }, 325 { .compatible = "nuvoton,wpcm450-uart", .data = (void *)PORT_NPCM, }, 326 { .compatible = "nuvoton,npcm750-uart", .data = (void *)PORT_NPCM, }, 327 { /* end of list */ }, 328 }; 329 MODULE_DEVICE_TABLE(of, of_platform_serial_table); 330 331 static struct platform_driver of_platform_serial_driver = { 332 .driver = { 333 .name = "of_serial", 334 .of_match_table = of_platform_serial_table, 335 .pm = &of_serial_pm_ops, 336 }, 337 .probe = of_platform_serial_probe, 338 .remove = of_platform_serial_remove, 339 }; 340 341 module_platform_driver(of_platform_serial_driver); 342 343 MODULE_AUTHOR("Arnd Bergmann <arnd@arndb.de>"); 344 MODULE_LICENSE("GPL"); 345 MODULE_DESCRIPTION("Serial Port driver for Open Firmware platform devices"); 346