1 // SPDX-License-Identifier: GPL-2.0+ 2 /* 3 * Mediatek 8250 driver. 4 * 5 * Copyright (c) 2014 MundoReader S.L. 6 * Author: Matthias Brugger <matthias.bgg@gmail.com> 7 */ 8 #include <linux/clk.h> 9 #include <linux/io.h> 10 #include <linux/module.h> 11 #include <linux/of_irq.h> 12 #include <linux/of_platform.h> 13 #include <linux/pinctrl/consumer.h> 14 #include <linux/platform_device.h> 15 #include <linux/pm_runtime.h> 16 #include <linux/serial_8250.h> 17 #include <linux/serial_reg.h> 18 #include <linux/console.h> 19 #include <linux/dma-mapping.h> 20 #include <linux/tty.h> 21 #include <linux/tty_flip.h> 22 23 #include "8250.h" 24 25 #define MTK_UART_HIGHS 0x09 /* Highspeed register */ 26 #define MTK_UART_SAMPLE_COUNT 0x0a /* Sample count register */ 27 #define MTK_UART_SAMPLE_POINT 0x0b /* Sample point register */ 28 #define MTK_UART_RATE_FIX 0x0d /* UART Rate Fix Register */ 29 #define MTK_UART_ESCAPE_DAT 0x10 /* Escape Character register */ 30 #define MTK_UART_ESCAPE_EN 0x11 /* Escape Enable register */ 31 #define MTK_UART_DMA_EN 0x13 /* DMA Enable register */ 32 #define MTK_UART_RXTRI_AD 0x14 /* RX Trigger address */ 33 #define MTK_UART_FRACDIV_L 0x15 /* Fractional divider LSB address */ 34 #define MTK_UART_FRACDIV_M 0x16 /* Fractional divider MSB address */ 35 #define MTK_UART_DEBUG0 0x18 36 #define MTK_UART_IER_XOFFI 0x20 /* Enable XOFF character interrupt */ 37 #define MTK_UART_IER_RTSI 0x40 /* Enable RTS Modem status interrupt */ 38 #define MTK_UART_IER_CTSI 0x80 /* Enable CTS Modem status interrupt */ 39 40 #define MTK_UART_EFR_EN 0x10 /* Enable enhancement feature */ 41 #define MTK_UART_EFR_RTS 0x40 /* Enable hardware rx flow control */ 42 #define MTK_UART_EFR_CTS 0x80 /* Enable hardware tx flow control */ 43 #define MTK_UART_EFR_NO_SW_FC 0x0 /* no sw flow control */ 44 #define MTK_UART_EFR_XON1_XOFF1 0xa /* XON1/XOFF1 as sw flow control */ 45 #define MTK_UART_EFR_XON2_XOFF2 0x5 /* XON2/XOFF2 as sw flow control */ 46 #define MTK_UART_EFR_SW_FC_MASK 0xf /* Enable CTS Modem status interrupt */ 47 #define MTK_UART_EFR_HW_FC (MTK_UART_EFR_RTS | MTK_UART_EFR_CTS) 48 #define MTK_UART_DMA_EN_TX 0x2 49 #define MTK_UART_DMA_EN_RX 0x5 50 51 #define MTK_UART_ESCAPE_CHAR 0x77 /* Escape char added under sw fc */ 52 #define MTK_UART_RX_SIZE 0x8000 53 #define MTK_UART_TX_TRIGGER 1 54 #define MTK_UART_RX_TRIGGER MTK_UART_RX_SIZE 55 56 #ifdef CONFIG_SERIAL_8250_DMA 57 enum dma_rx_status { 58 DMA_RX_START = 0, 59 DMA_RX_RUNNING = 1, 60 DMA_RX_SHUTDOWN = 2, 61 }; 62 #endif 63 64 struct mtk8250_data { 65 int line; 66 unsigned int rx_pos; 67 unsigned int clk_count; 68 struct clk *uart_clk; 69 struct clk *bus_clk; 70 struct uart_8250_dma *dma; 71 #ifdef CONFIG_SERIAL_8250_DMA 72 enum dma_rx_status rx_status; 73 #endif 74 int rx_wakeup_irq; 75 }; 76 77 /* flow control mode */ 78 enum { 79 MTK_UART_FC_NONE, 80 MTK_UART_FC_SW, 81 MTK_UART_FC_HW, 82 }; 83 84 #ifdef CONFIG_SERIAL_8250_DMA 85 static void mtk8250_rx_dma(struct uart_8250_port *up); 86 87 static void mtk8250_dma_rx_complete(void *param) 88 { 89 struct uart_8250_port *up = param; 90 struct uart_8250_dma *dma = up->dma; 91 struct mtk8250_data *data = up->port.private_data; 92 struct tty_port *tty_port = &up->port.state->port; 93 struct dma_tx_state state; 94 int copied, total, cnt; 95 unsigned char *ptr; 96 unsigned long flags; 97 98 if (data->rx_status == DMA_RX_SHUTDOWN) 99 return; 100 101 spin_lock_irqsave(&up->port.lock, flags); 102 103 dmaengine_tx_status(dma->rxchan, dma->rx_cookie, &state); 104 total = dma->rx_size - state.residue; 105 cnt = total; 106 107 if ((data->rx_pos + cnt) > dma->rx_size) 108 cnt = dma->rx_size - data->rx_pos; 109 110 ptr = (unsigned char *)(data->rx_pos + dma->rx_buf); 111 copied = tty_insert_flip_string(tty_port, ptr, cnt); 112 data->rx_pos += cnt; 113 114 if (total > cnt) { 115 ptr = (unsigned char *)(dma->rx_buf); 116 cnt = total - cnt; 117 copied += tty_insert_flip_string(tty_port, ptr, cnt); 118 data->rx_pos = cnt; 119 } 120 121 up->port.icount.rx += copied; 122 123 tty_flip_buffer_push(tty_port); 124 125 mtk8250_rx_dma(up); 126 127 spin_unlock_irqrestore(&up->port.lock, flags); 128 } 129 130 static void mtk8250_rx_dma(struct uart_8250_port *up) 131 { 132 struct uart_8250_dma *dma = up->dma; 133 struct dma_async_tx_descriptor *desc; 134 135 desc = dmaengine_prep_slave_single(dma->rxchan, dma->rx_addr, 136 dma->rx_size, DMA_DEV_TO_MEM, 137 DMA_PREP_INTERRUPT | DMA_CTRL_ACK); 138 if (!desc) { 139 pr_err("failed to prepare rx slave single\n"); 140 return; 141 } 142 143 desc->callback = mtk8250_dma_rx_complete; 144 desc->callback_param = up; 145 146 dma->rx_cookie = dmaengine_submit(desc); 147 148 dma_async_issue_pending(dma->rxchan); 149 } 150 151 static void mtk8250_dma_enable(struct uart_8250_port *up) 152 { 153 struct uart_8250_dma *dma = up->dma; 154 struct mtk8250_data *data = up->port.private_data; 155 int lcr = serial_in(up, UART_LCR); 156 157 if (data->rx_status != DMA_RX_START) 158 return; 159 160 dma->rxconf.src_port_window_size = dma->rx_size; 161 dma->rxconf.src_addr = dma->rx_addr; 162 163 dma->txconf.dst_port_window_size = UART_XMIT_SIZE; 164 dma->txconf.dst_addr = dma->tx_addr; 165 166 serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO | UART_FCR_CLEAR_RCVR | 167 UART_FCR_CLEAR_XMIT); 168 serial_out(up, MTK_UART_DMA_EN, 169 MTK_UART_DMA_EN_RX | MTK_UART_DMA_EN_TX); 170 171 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); 172 serial_out(up, UART_EFR, UART_EFR_ECB); 173 serial_out(up, UART_LCR, lcr); 174 175 if (dmaengine_slave_config(dma->rxchan, &dma->rxconf) != 0) 176 pr_err("failed to configure rx dma channel\n"); 177 if (dmaengine_slave_config(dma->txchan, &dma->txconf) != 0) 178 pr_err("failed to configure tx dma channel\n"); 179 180 data->rx_status = DMA_RX_RUNNING; 181 data->rx_pos = 0; 182 mtk8250_rx_dma(up); 183 } 184 #endif 185 186 static int mtk8250_startup(struct uart_port *port) 187 { 188 #ifdef CONFIG_SERIAL_8250_DMA 189 struct uart_8250_port *up = up_to_u8250p(port); 190 struct mtk8250_data *data = port->private_data; 191 192 /* disable DMA for console */ 193 if (uart_console(port)) 194 up->dma = NULL; 195 196 if (up->dma) { 197 data->rx_status = DMA_RX_START; 198 uart_circ_clear(&port->state->xmit); 199 } 200 #endif 201 memset(&port->icount, 0, sizeof(port->icount)); 202 203 return serial8250_do_startup(port); 204 } 205 206 static void mtk8250_shutdown(struct uart_port *port) 207 { 208 #ifdef CONFIG_SERIAL_8250_DMA 209 struct uart_8250_port *up = up_to_u8250p(port); 210 struct mtk8250_data *data = port->private_data; 211 212 if (up->dma) 213 data->rx_status = DMA_RX_SHUTDOWN; 214 #endif 215 216 return serial8250_do_shutdown(port); 217 } 218 219 static void mtk8250_disable_intrs(struct uart_8250_port *up, int mask) 220 { 221 serial_out(up, UART_IER, serial_in(up, UART_IER) & (~mask)); 222 } 223 224 static void mtk8250_enable_intrs(struct uart_8250_port *up, int mask) 225 { 226 serial_out(up, UART_IER, serial_in(up, UART_IER) | mask); 227 } 228 229 static void mtk8250_set_flow_ctrl(struct uart_8250_port *up, int mode) 230 { 231 struct uart_port *port = &up->port; 232 int lcr = serial_in(up, UART_LCR); 233 234 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); 235 serial_out(up, UART_EFR, UART_EFR_ECB); 236 serial_out(up, UART_LCR, lcr); 237 lcr = serial_in(up, UART_LCR); 238 239 switch (mode) { 240 case MTK_UART_FC_NONE: 241 serial_out(up, MTK_UART_ESCAPE_DAT, MTK_UART_ESCAPE_CHAR); 242 serial_out(up, MTK_UART_ESCAPE_EN, 0x00); 243 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); 244 serial_out(up, UART_EFR, serial_in(up, UART_EFR) & 245 (~(MTK_UART_EFR_HW_FC | MTK_UART_EFR_SW_FC_MASK))); 246 serial_out(up, UART_LCR, lcr); 247 mtk8250_disable_intrs(up, MTK_UART_IER_XOFFI | 248 MTK_UART_IER_RTSI | MTK_UART_IER_CTSI); 249 break; 250 251 case MTK_UART_FC_HW: 252 serial_out(up, MTK_UART_ESCAPE_DAT, MTK_UART_ESCAPE_CHAR); 253 serial_out(up, MTK_UART_ESCAPE_EN, 0x00); 254 serial_out(up, UART_MCR, UART_MCR_RTS); 255 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); 256 257 /*enable hw flow control*/ 258 serial_out(up, UART_EFR, MTK_UART_EFR_HW_FC | 259 (serial_in(up, UART_EFR) & 260 (~(MTK_UART_EFR_HW_FC | MTK_UART_EFR_SW_FC_MASK)))); 261 262 serial_out(up, UART_LCR, lcr); 263 mtk8250_disable_intrs(up, MTK_UART_IER_XOFFI); 264 mtk8250_enable_intrs(up, MTK_UART_IER_CTSI | MTK_UART_IER_RTSI); 265 break; 266 267 case MTK_UART_FC_SW: /*MTK software flow control */ 268 serial_out(up, MTK_UART_ESCAPE_DAT, MTK_UART_ESCAPE_CHAR); 269 serial_out(up, MTK_UART_ESCAPE_EN, 0x01); 270 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); 271 272 /*enable sw flow control */ 273 serial_out(up, UART_EFR, MTK_UART_EFR_XON1_XOFF1 | 274 (serial_in(up, UART_EFR) & 275 (~(MTK_UART_EFR_HW_FC | MTK_UART_EFR_SW_FC_MASK)))); 276 277 serial_out(up, UART_XON1, START_CHAR(port->state->port.tty)); 278 serial_out(up, UART_XOFF1, STOP_CHAR(port->state->port.tty)); 279 serial_out(up, UART_LCR, lcr); 280 mtk8250_disable_intrs(up, MTK_UART_IER_CTSI|MTK_UART_IER_RTSI); 281 mtk8250_enable_intrs(up, MTK_UART_IER_XOFFI); 282 break; 283 default: 284 break; 285 } 286 } 287 288 static void 289 mtk8250_set_termios(struct uart_port *port, struct ktermios *termios, 290 struct ktermios *old) 291 { 292 static const unsigned short fraction_L_mapping[] = { 293 0, 1, 0x5, 0x15, 0x55, 0x57, 0x57, 0x77, 0x7F, 0xFF, 0xFF 294 }; 295 static const unsigned short fraction_M_mapping[] = { 296 0, 0, 0, 0, 0, 0, 1, 1, 1, 1, 3 297 }; 298 struct uart_8250_port *up = up_to_u8250p(port); 299 unsigned int baud, quot, fraction; 300 unsigned long flags; 301 int mode; 302 303 #ifdef CONFIG_SERIAL_8250_DMA 304 if (up->dma) { 305 if (uart_console(port)) { 306 devm_kfree(up->port.dev, up->dma); 307 up->dma = NULL; 308 } else { 309 mtk8250_dma_enable(up); 310 } 311 } 312 #endif 313 314 /* 315 * Store the requested baud rate before calling the generic 8250 316 * set_termios method. Standard 8250 port expects bauds to be 317 * no higher than (uartclk / 16) so the baud will be clamped if it 318 * gets out of that bound. Mediatek 8250 port supports speed 319 * higher than that, therefore we'll get original baud rate back 320 * after calling the generic set_termios method and recalculate 321 * the speed later in this method. 322 */ 323 baud = tty_termios_baud_rate(termios); 324 325 serial8250_do_set_termios(port, termios, NULL); 326 327 tty_termios_encode_baud_rate(termios, baud, baud); 328 329 /* 330 * Mediatek UARTs use an extra highspeed register (MTK_UART_HIGHS) 331 * 332 * We need to recalcualte the quot register, as the claculation depends 333 * on the vaule in the highspeed register. 334 * 335 * Some baudrates are not supported by the chip, so we use the next 336 * lower rate supported and update termios c_flag. 337 * 338 * If highspeed register is set to 3, we need to specify sample count 339 * and sample point to increase accuracy. If not, we reset the 340 * registers to their default values. 341 */ 342 baud = uart_get_baud_rate(port, termios, old, 343 port->uartclk / 16 / UART_DIV_MAX, 344 port->uartclk); 345 346 if (baud < 115200) { 347 serial_port_out(port, MTK_UART_HIGHS, 0x0); 348 quot = uart_get_divisor(port, baud); 349 } else { 350 serial_port_out(port, MTK_UART_HIGHS, 0x3); 351 quot = DIV_ROUND_UP(port->uartclk, 256 * baud); 352 } 353 354 /* 355 * Ok, we're now changing the port state. Do it with 356 * interrupts disabled. 357 */ 358 spin_lock_irqsave(&port->lock, flags); 359 360 /* 361 * Update the per-port timeout. 362 */ 363 uart_update_timeout(port, termios->c_cflag, baud); 364 365 /* set DLAB we have cval saved in up->lcr from the call to the core */ 366 serial_port_out(port, UART_LCR, up->lcr | UART_LCR_DLAB); 367 serial_dl_write(up, quot); 368 369 /* reset DLAB */ 370 serial_port_out(port, UART_LCR, up->lcr); 371 372 if (baud >= 115200) { 373 unsigned int tmp; 374 375 tmp = (port->uartclk / (baud * quot)) - 1; 376 serial_port_out(port, MTK_UART_SAMPLE_COUNT, tmp); 377 serial_port_out(port, MTK_UART_SAMPLE_POINT, 378 (tmp >> 1) - 1); 379 380 /*count fraction to set fractoin register */ 381 fraction = ((port->uartclk * 100) / baud / quot) % 100; 382 fraction = DIV_ROUND_CLOSEST(fraction, 10); 383 serial_port_out(port, MTK_UART_FRACDIV_L, 384 fraction_L_mapping[fraction]); 385 serial_port_out(port, MTK_UART_FRACDIV_M, 386 fraction_M_mapping[fraction]); 387 } else { 388 serial_port_out(port, MTK_UART_SAMPLE_COUNT, 0x00); 389 serial_port_out(port, MTK_UART_SAMPLE_POINT, 0xff); 390 serial_port_out(port, MTK_UART_FRACDIV_L, 0x00); 391 serial_port_out(port, MTK_UART_FRACDIV_M, 0x00); 392 } 393 394 if ((termios->c_cflag & CRTSCTS) && (!(termios->c_iflag & CRTSCTS))) 395 mode = MTK_UART_FC_HW; 396 else if (termios->c_iflag & CRTSCTS) 397 mode = MTK_UART_FC_SW; 398 else 399 mode = MTK_UART_FC_NONE; 400 401 mtk8250_set_flow_ctrl(up, mode); 402 403 if (uart_console(port)) 404 up->port.cons->cflag = termios->c_cflag; 405 406 spin_unlock_irqrestore(&port->lock, flags); 407 /* Don't rewrite B0 */ 408 if (tty_termios_baud_rate(termios)) 409 tty_termios_encode_baud_rate(termios, baud, baud); 410 } 411 412 static int __maybe_unused mtk8250_runtime_suspend(struct device *dev) 413 { 414 struct mtk8250_data *data = dev_get_drvdata(dev); 415 struct uart_8250_port *up = serial8250_get_port(data->line); 416 417 /* wait until UART in idle status */ 418 while 419 (serial_in(up, MTK_UART_DEBUG0)); 420 421 if (data->clk_count == 0U) { 422 dev_dbg(dev, "%s clock count is 0\n", __func__); 423 } else { 424 clk_disable_unprepare(data->bus_clk); 425 data->clk_count--; 426 } 427 428 return 0; 429 } 430 431 static int __maybe_unused mtk8250_runtime_resume(struct device *dev) 432 { 433 struct mtk8250_data *data = dev_get_drvdata(dev); 434 int err; 435 436 if (data->clk_count > 0U) { 437 dev_dbg(dev, "%s clock count is %d\n", __func__, 438 data->clk_count); 439 } else { 440 err = clk_prepare_enable(data->bus_clk); 441 if (err) { 442 dev_warn(dev, "Can't enable bus clock\n"); 443 return err; 444 } 445 data->clk_count++; 446 } 447 448 return 0; 449 } 450 451 static void 452 mtk8250_do_pm(struct uart_port *port, unsigned int state, unsigned int old) 453 { 454 if (!state) 455 if (!mtk8250_runtime_resume(port->dev)) 456 pm_runtime_get_sync(port->dev); 457 458 serial8250_do_pm(port, state, old); 459 460 if (state) 461 if (!pm_runtime_put_sync_suspend(port->dev)) 462 mtk8250_runtime_suspend(port->dev); 463 } 464 465 #ifdef CONFIG_SERIAL_8250_DMA 466 static bool mtk8250_dma_filter(struct dma_chan *chan, void *param) 467 { 468 return false; 469 } 470 #endif 471 472 static int mtk8250_probe_of(struct platform_device *pdev, struct uart_port *p, 473 struct mtk8250_data *data) 474 { 475 #ifdef CONFIG_SERIAL_8250_DMA 476 int dmacnt; 477 #endif 478 479 data->uart_clk = devm_clk_get(&pdev->dev, "baud"); 480 if (IS_ERR(data->uart_clk)) { 481 /* 482 * For compatibility with older device trees try unnamed 483 * clk when no baud clk can be found. 484 */ 485 data->uart_clk = devm_clk_get(&pdev->dev, NULL); 486 if (IS_ERR(data->uart_clk)) { 487 dev_warn(&pdev->dev, "Can't get uart clock\n"); 488 return PTR_ERR(data->uart_clk); 489 } 490 491 return 0; 492 } 493 494 data->bus_clk = devm_clk_get(&pdev->dev, "bus"); 495 if (IS_ERR(data->bus_clk)) 496 return PTR_ERR(data->bus_clk); 497 498 data->dma = NULL; 499 #ifdef CONFIG_SERIAL_8250_DMA 500 dmacnt = of_property_count_strings(pdev->dev.of_node, "dma-names"); 501 if (dmacnt == 2) { 502 data->dma = devm_kzalloc(&pdev->dev, sizeof(*data->dma), 503 GFP_KERNEL); 504 if (!data->dma) 505 return -ENOMEM; 506 507 data->dma->fn = mtk8250_dma_filter; 508 data->dma->rx_size = MTK_UART_RX_SIZE; 509 data->dma->rxconf.src_maxburst = MTK_UART_RX_TRIGGER; 510 data->dma->txconf.dst_maxburst = MTK_UART_TX_TRIGGER; 511 } 512 #endif 513 514 return 0; 515 } 516 517 static int mtk8250_probe(struct platform_device *pdev) 518 { 519 struct uart_8250_port uart = {}; 520 struct mtk8250_data *data; 521 struct resource *regs; 522 int irq, err; 523 524 irq = platform_get_irq(pdev, 0); 525 if (irq < 0) 526 return irq; 527 528 regs = platform_get_resource(pdev, IORESOURCE_MEM, 0); 529 if (!regs) { 530 dev_err(&pdev->dev, "no registers defined\n"); 531 return -EINVAL; 532 } 533 534 uart.port.membase = devm_ioremap(&pdev->dev, regs->start, 535 resource_size(regs)); 536 if (!uart.port.membase) 537 return -ENOMEM; 538 539 data = devm_kzalloc(&pdev->dev, sizeof(*data), GFP_KERNEL); 540 if (!data) 541 return -ENOMEM; 542 543 data->clk_count = 0; 544 545 if (pdev->dev.of_node) { 546 err = mtk8250_probe_of(pdev, &uart.port, data); 547 if (err) 548 return err; 549 } else 550 return -ENODEV; 551 552 spin_lock_init(&uart.port.lock); 553 uart.port.mapbase = regs->start; 554 uart.port.irq = irq; 555 uart.port.pm = mtk8250_do_pm; 556 uart.port.type = PORT_16550; 557 uart.port.flags = UPF_BOOT_AUTOCONF | UPF_FIXED_PORT; 558 uart.port.dev = &pdev->dev; 559 uart.port.iotype = UPIO_MEM32; 560 uart.port.regshift = 2; 561 uart.port.private_data = data; 562 uart.port.shutdown = mtk8250_shutdown; 563 uart.port.startup = mtk8250_startup; 564 uart.port.set_termios = mtk8250_set_termios; 565 uart.port.uartclk = clk_get_rate(data->uart_clk); 566 #ifdef CONFIG_SERIAL_8250_DMA 567 if (data->dma) 568 uart.dma = data->dma; 569 #endif 570 571 /* Disable Rate Fix function */ 572 writel(0x0, uart.port.membase + 573 (MTK_UART_RATE_FIX << uart.port.regshift)); 574 575 platform_set_drvdata(pdev, data); 576 577 pm_runtime_enable(&pdev->dev); 578 err = mtk8250_runtime_resume(&pdev->dev); 579 if (err) 580 goto err_pm_disable; 581 582 data->line = serial8250_register_8250_port(&uart); 583 if (data->line < 0) { 584 err = data->line; 585 goto err_pm_disable; 586 } 587 588 data->rx_wakeup_irq = platform_get_irq_optional(pdev, 1); 589 590 return 0; 591 592 err_pm_disable: 593 pm_runtime_disable(&pdev->dev); 594 595 return err; 596 } 597 598 static int mtk8250_remove(struct platform_device *pdev) 599 { 600 struct mtk8250_data *data = platform_get_drvdata(pdev); 601 602 pm_runtime_get_sync(&pdev->dev); 603 604 serial8250_unregister_port(data->line); 605 606 pm_runtime_disable(&pdev->dev); 607 pm_runtime_put_noidle(&pdev->dev); 608 609 if (!pm_runtime_status_suspended(&pdev->dev)) 610 mtk8250_runtime_suspend(&pdev->dev); 611 612 return 0; 613 } 614 615 static int __maybe_unused mtk8250_suspend(struct device *dev) 616 { 617 struct mtk8250_data *data = dev_get_drvdata(dev); 618 int irq = data->rx_wakeup_irq; 619 int err; 620 621 serial8250_suspend_port(data->line); 622 623 pinctrl_pm_select_sleep_state(dev); 624 if (irq >= 0) { 625 err = enable_irq_wake(irq); 626 if (err) { 627 dev_err(dev, 628 "failed to enable irq wake on IRQ %d: %d\n", 629 irq, err); 630 pinctrl_pm_select_default_state(dev); 631 serial8250_resume_port(data->line); 632 return err; 633 } 634 } 635 636 return 0; 637 } 638 639 static int __maybe_unused mtk8250_resume(struct device *dev) 640 { 641 struct mtk8250_data *data = dev_get_drvdata(dev); 642 int irq = data->rx_wakeup_irq; 643 644 if (irq >= 0) 645 disable_irq_wake(irq); 646 pinctrl_pm_select_default_state(dev); 647 648 serial8250_resume_port(data->line); 649 650 return 0; 651 } 652 653 static const struct dev_pm_ops mtk8250_pm_ops = { 654 SET_SYSTEM_SLEEP_PM_OPS(mtk8250_suspend, mtk8250_resume) 655 SET_RUNTIME_PM_OPS(mtk8250_runtime_suspend, mtk8250_runtime_resume, 656 NULL) 657 }; 658 659 static const struct of_device_id mtk8250_of_match[] = { 660 { .compatible = "mediatek,mt6577-uart" }, 661 { /* Sentinel */ } 662 }; 663 MODULE_DEVICE_TABLE(of, mtk8250_of_match); 664 665 static struct platform_driver mtk8250_platform_driver = { 666 .driver = { 667 .name = "mt6577-uart", 668 .pm = &mtk8250_pm_ops, 669 .of_match_table = mtk8250_of_match, 670 }, 671 .probe = mtk8250_probe, 672 .remove = mtk8250_remove, 673 }; 674 module_platform_driver(mtk8250_platform_driver); 675 676 #ifdef CONFIG_SERIAL_8250_CONSOLE 677 static int __init early_mtk8250_setup(struct earlycon_device *device, 678 const char *options) 679 { 680 if (!device->port.membase) 681 return -ENODEV; 682 683 device->port.iotype = UPIO_MEM32; 684 device->port.regshift = 2; 685 686 return early_serial8250_setup(device, NULL); 687 } 688 689 OF_EARLYCON_DECLARE(mtk8250, "mediatek,mt6577-uart", early_mtk8250_setup); 690 #endif 691 692 MODULE_AUTHOR("Matthias Brugger"); 693 MODULE_LICENSE("GPL"); 694 MODULE_DESCRIPTION("Mediatek 8250 serial port driver"); 695