1 // SPDX-License-Identifier: GPL-2.0 2 /* 3 * Probe module for 8250/16550-type Exar chips PCI serial ports. 4 * 5 * Based on drivers/tty/serial/8250/8250_pci.c, 6 * 7 * Copyright (C) 2017 Sudip Mukherjee, All Rights Reserved. 8 */ 9 #include <linux/acpi.h> 10 #include <linux/dmi.h> 11 #include <linux/io.h> 12 #include <linux/kernel.h> 13 #include <linux/module.h> 14 #include <linux/pci.h> 15 #include <linux/property.h> 16 #include <linux/serial_core.h> 17 #include <linux/serial_reg.h> 18 #include <linux/slab.h> 19 #include <linux/string.h> 20 #include <linux/tty.h> 21 #include <linux/8250_pci.h> 22 #include <linux/delay.h> 23 24 #include <asm/byteorder.h> 25 26 #include "8250.h" 27 28 #define PCI_DEVICE_ID_ACCESSIO_COM_2S 0x1052 29 #define PCI_DEVICE_ID_ACCESSIO_COM_4S 0x105d 30 #define PCI_DEVICE_ID_ACCESSIO_COM_8S 0x106c 31 #define PCI_DEVICE_ID_ACCESSIO_COM232_8 0x10a8 32 #define PCI_DEVICE_ID_ACCESSIO_COM_2SM 0x10d2 33 #define PCI_DEVICE_ID_ACCESSIO_COM_4SM 0x10db 34 #define PCI_DEVICE_ID_ACCESSIO_COM_8SM 0x10ea 35 36 #define PCI_DEVICE_ID_COMMTECH_4224PCI335 0x0002 37 #define PCI_DEVICE_ID_COMMTECH_4222PCI335 0x0004 38 #define PCI_DEVICE_ID_COMMTECH_2324PCI335 0x000a 39 #define PCI_DEVICE_ID_COMMTECH_2328PCI335 0x000b 40 #define PCI_DEVICE_ID_COMMTECH_4224PCIE 0x0020 41 #define PCI_DEVICE_ID_COMMTECH_4228PCIE 0x0021 42 #define PCI_DEVICE_ID_COMMTECH_4222PCIE 0x0022 43 #define PCI_DEVICE_ID_EXAR_XR17V4358 0x4358 44 #define PCI_DEVICE_ID_EXAR_XR17V8358 0x8358 45 46 #define UART_EXAR_INT0 0x80 47 #define UART_EXAR_8XMODE 0x88 /* 8X sampling rate select */ 48 #define UART_EXAR_SLEEP 0x8b /* Sleep mode */ 49 #define UART_EXAR_DVID 0x8d /* Device identification */ 50 51 #define UART_EXAR_FCTR 0x08 /* Feature Control Register */ 52 #define UART_FCTR_EXAR_IRDA 0x10 /* IrDa data encode select */ 53 #define UART_FCTR_EXAR_485 0x20 /* Auto 485 half duplex dir ctl */ 54 #define UART_FCTR_EXAR_TRGA 0x00 /* FIFO trigger table A */ 55 #define UART_FCTR_EXAR_TRGB 0x60 /* FIFO trigger table B */ 56 #define UART_FCTR_EXAR_TRGC 0x80 /* FIFO trigger table C */ 57 #define UART_FCTR_EXAR_TRGD 0xc0 /* FIFO trigger table D programmable */ 58 59 #define UART_EXAR_TXTRG 0x0a /* Tx FIFO trigger level write-only */ 60 #define UART_EXAR_RXTRG 0x0b /* Rx FIFO trigger level write-only */ 61 62 #define UART_EXAR_MPIOINT_7_0 0x8f /* MPIOINT[7:0] */ 63 #define UART_EXAR_MPIOLVL_7_0 0x90 /* MPIOLVL[7:0] */ 64 #define UART_EXAR_MPIO3T_7_0 0x91 /* MPIO3T[7:0] */ 65 #define UART_EXAR_MPIOINV_7_0 0x92 /* MPIOINV[7:0] */ 66 #define UART_EXAR_MPIOSEL_7_0 0x93 /* MPIOSEL[7:0] */ 67 #define UART_EXAR_MPIOOD_7_0 0x94 /* MPIOOD[7:0] */ 68 #define UART_EXAR_MPIOINT_15_8 0x95 /* MPIOINT[15:8] */ 69 #define UART_EXAR_MPIOLVL_15_8 0x96 /* MPIOLVL[15:8] */ 70 #define UART_EXAR_MPIO3T_15_8 0x97 /* MPIO3T[15:8] */ 71 #define UART_EXAR_MPIOINV_15_8 0x98 /* MPIOINV[15:8] */ 72 #define UART_EXAR_MPIOSEL_15_8 0x99 /* MPIOSEL[15:8] */ 73 #define UART_EXAR_MPIOOD_15_8 0x9a /* MPIOOD[15:8] */ 74 75 #define UART_EXAR_RS485_DLY(x) ((x) << 4) 76 77 /* 78 * IOT2040 MPIO wiring semantics: 79 * 80 * MPIO Port Function 81 * ---- ---- -------- 82 * 0 2 Mode bit 0 83 * 1 2 Mode bit 1 84 * 2 2 Terminate bus 85 * 3 - <reserved> 86 * 4 3 Mode bit 0 87 * 5 3 Mode bit 1 88 * 6 3 Terminate bus 89 * 7 - <reserved> 90 * 8 2 Enable 91 * 9 3 Enable 92 * 10 - Red LED 93 * 11..15 - <unused> 94 */ 95 96 /* IOT2040 MPIOs 0..7 */ 97 #define IOT2040_UART_MODE_RS232 0x01 98 #define IOT2040_UART_MODE_RS485 0x02 99 #define IOT2040_UART_MODE_RS422 0x03 100 #define IOT2040_UART_TERMINATE_BUS 0x04 101 102 #define IOT2040_UART1_MASK 0x0f 103 #define IOT2040_UART2_SHIFT 4 104 105 #define IOT2040_UARTS_DEFAULT_MODE 0x11 /* both RS232 */ 106 #define IOT2040_UARTS_GPIO_LO_MODE 0x88 /* reserved pins as input */ 107 108 /* IOT2040 MPIOs 8..15 */ 109 #define IOT2040_UARTS_ENABLE 0x03 110 #define IOT2040_UARTS_GPIO_HI_MODE 0xF8 /* enable & LED as outputs */ 111 112 struct exar8250; 113 114 struct exar8250_platform { 115 int (*rs485_config)(struct uart_port *, struct serial_rs485 *); 116 int (*register_gpio)(struct pci_dev *, struct uart_8250_port *); 117 void (*unregister_gpio)(struct uart_8250_port *); 118 }; 119 120 /** 121 * struct exar8250_board - board information 122 * @num_ports: number of serial ports 123 * @reg_shift: describes UART register mapping in PCI memory 124 * @setup: quirk run at ->probe() stage 125 * @exit: quirk run at ->remove() stage 126 */ 127 struct exar8250_board { 128 unsigned int num_ports; 129 unsigned int reg_shift; 130 int (*setup)(struct exar8250 *, struct pci_dev *, 131 struct uart_8250_port *, int); 132 void (*exit)(struct pci_dev *pcidev); 133 }; 134 135 struct exar8250 { 136 unsigned int nr; 137 struct exar8250_board *board; 138 void __iomem *virt; 139 int line[]; 140 }; 141 142 static void exar_pm(struct uart_port *port, unsigned int state, unsigned int old) 143 { 144 /* 145 * Exar UARTs have a SLEEP register that enables or disables each UART 146 * to enter sleep mode separately. On the XR17V35x the register 147 * is accessible to each UART at the UART_EXAR_SLEEP offset, but 148 * the UART channel may only write to the corresponding bit. 149 */ 150 serial_port_out(port, UART_EXAR_SLEEP, state ? 0xff : 0); 151 } 152 153 /* 154 * XR17V35x UARTs have an extra fractional divisor register (DLD) 155 * Calculate divisor with extra 4-bit fractional portion 156 */ 157 static unsigned int xr17v35x_get_divisor(struct uart_port *p, unsigned int baud, 158 unsigned int *frac) 159 { 160 unsigned int quot_16; 161 162 quot_16 = DIV_ROUND_CLOSEST(p->uartclk, baud); 163 *frac = quot_16 & 0x0f; 164 165 return quot_16 >> 4; 166 } 167 168 static void xr17v35x_set_divisor(struct uart_port *p, unsigned int baud, 169 unsigned int quot, unsigned int quot_frac) 170 { 171 serial8250_do_set_divisor(p, baud, quot, quot_frac); 172 173 /* Preserve bits not related to baudrate; DLD[7:4]. */ 174 quot_frac |= serial_port_in(p, 0x2) & 0xf0; 175 serial_port_out(p, 0x2, quot_frac); 176 } 177 178 static int xr17v35x_startup(struct uart_port *port) 179 { 180 /* 181 * First enable access to IER [7:5], ISR [5:4], FCR [5:4], 182 * MCR [7:5] and MSR [7:0] 183 */ 184 serial_port_out(port, UART_XR_EFR, UART_EFR_ECB); 185 186 /* 187 * Make sure all interrups are masked until initialization is 188 * complete and the FIFOs are cleared 189 */ 190 serial_port_out(port, UART_IER, 0); 191 192 return serial8250_do_startup(port); 193 } 194 195 static void exar_shutdown(struct uart_port *port) 196 { 197 unsigned char lsr; 198 bool tx_complete = false; 199 struct uart_8250_port *up = up_to_u8250p(port); 200 struct circ_buf *xmit = &port->state->xmit; 201 int i = 0; 202 203 do { 204 lsr = serial_in(up, UART_LSR); 205 if (lsr & (UART_LSR_TEMT | UART_LSR_THRE)) 206 tx_complete = true; 207 else 208 tx_complete = false; 209 usleep_range(1000, 1100); 210 } while (!uart_circ_empty(xmit) && !tx_complete && i++ < 1000); 211 212 serial8250_do_shutdown(port); 213 } 214 215 static int default_setup(struct exar8250 *priv, struct pci_dev *pcidev, 216 int idx, unsigned int offset, 217 struct uart_8250_port *port) 218 { 219 const struct exar8250_board *board = priv->board; 220 unsigned int bar = 0; 221 unsigned char status; 222 223 port->port.iotype = UPIO_MEM; 224 port->port.mapbase = pci_resource_start(pcidev, bar) + offset; 225 port->port.membase = priv->virt + offset; 226 port->port.regshift = board->reg_shift; 227 228 /* 229 * XR17V35x UARTs have an extra divisor register, DLD that gets enabled 230 * with when DLAB is set which will cause the device to incorrectly match 231 * and assign port type to PORT_16650. The EFR for this UART is found 232 * at offset 0x09. Instead check the Deice ID (DVID) register 233 * for a 2, 4 or 8 port UART. 234 */ 235 status = readb(port->port.membase + UART_EXAR_DVID); 236 if (status == 0x82 || status == 0x84 || status == 0x88) { 237 port->port.type = PORT_XR17V35X; 238 239 port->port.get_divisor = xr17v35x_get_divisor; 240 port->port.set_divisor = xr17v35x_set_divisor; 241 242 port->port.startup = xr17v35x_startup; 243 } else { 244 port->port.type = PORT_XR17D15X; 245 } 246 247 port->port.pm = exar_pm; 248 port->port.shutdown = exar_shutdown; 249 250 return 0; 251 } 252 253 static int 254 pci_fastcom335_setup(struct exar8250 *priv, struct pci_dev *pcidev, 255 struct uart_8250_port *port, int idx) 256 { 257 unsigned int offset = idx * 0x200; 258 unsigned int baud = 1843200; 259 u8 __iomem *p; 260 int err; 261 262 port->port.uartclk = baud * 16; 263 264 err = default_setup(priv, pcidev, idx, offset, port); 265 if (err) 266 return err; 267 268 p = port->port.membase; 269 270 writeb(0x00, p + UART_EXAR_8XMODE); 271 writeb(UART_FCTR_EXAR_TRGD, p + UART_EXAR_FCTR); 272 writeb(32, p + UART_EXAR_TXTRG); 273 writeb(32, p + UART_EXAR_RXTRG); 274 275 /* 276 * Setup Multipurpose Input/Output pins. 277 */ 278 if (idx == 0) { 279 switch (pcidev->device) { 280 case PCI_DEVICE_ID_COMMTECH_4222PCI335: 281 case PCI_DEVICE_ID_COMMTECH_4224PCI335: 282 writeb(0x78, p + UART_EXAR_MPIOLVL_7_0); 283 writeb(0x00, p + UART_EXAR_MPIOINV_7_0); 284 writeb(0x00, p + UART_EXAR_MPIOSEL_7_0); 285 break; 286 case PCI_DEVICE_ID_COMMTECH_2324PCI335: 287 case PCI_DEVICE_ID_COMMTECH_2328PCI335: 288 writeb(0x00, p + UART_EXAR_MPIOLVL_7_0); 289 writeb(0xc0, p + UART_EXAR_MPIOINV_7_0); 290 writeb(0xc0, p + UART_EXAR_MPIOSEL_7_0); 291 break; 292 } 293 writeb(0x00, p + UART_EXAR_MPIOINT_7_0); 294 writeb(0x00, p + UART_EXAR_MPIO3T_7_0); 295 writeb(0x00, p + UART_EXAR_MPIOOD_7_0); 296 } 297 298 return 0; 299 } 300 301 static int 302 pci_connect_tech_setup(struct exar8250 *priv, struct pci_dev *pcidev, 303 struct uart_8250_port *port, int idx) 304 { 305 unsigned int offset = idx * 0x200; 306 unsigned int baud = 1843200; 307 308 port->port.uartclk = baud * 16; 309 return default_setup(priv, pcidev, idx, offset, port); 310 } 311 312 static int 313 pci_xr17c154_setup(struct exar8250 *priv, struct pci_dev *pcidev, 314 struct uart_8250_port *port, int idx) 315 { 316 unsigned int offset = idx * 0x200; 317 unsigned int baud = 921600; 318 319 port->port.uartclk = baud * 16; 320 return default_setup(priv, pcidev, idx, offset, port); 321 } 322 323 static void setup_gpio(struct pci_dev *pcidev, u8 __iomem *p) 324 { 325 /* 326 * The Commtech adapters required the MPIOs to be driven low. The Exar 327 * devices will export them as GPIOs, so we pre-configure them safely 328 * as inputs. 329 */ 330 331 u8 dir = 0x00; 332 333 if ((pcidev->vendor == PCI_VENDOR_ID_EXAR) && 334 (pcidev->subsystem_vendor != PCI_VENDOR_ID_SEALEVEL)) { 335 // Configure GPIO as inputs for Commtech adapters 336 dir = 0xff; 337 } else { 338 // Configure GPIO as outputs for SeaLevel adapters 339 dir = 0x00; 340 } 341 342 writeb(0x00, p + UART_EXAR_MPIOINT_7_0); 343 writeb(0x00, p + UART_EXAR_MPIOLVL_7_0); 344 writeb(0x00, p + UART_EXAR_MPIO3T_7_0); 345 writeb(0x00, p + UART_EXAR_MPIOINV_7_0); 346 writeb(dir, p + UART_EXAR_MPIOSEL_7_0); 347 writeb(0x00, p + UART_EXAR_MPIOOD_7_0); 348 writeb(0x00, p + UART_EXAR_MPIOINT_15_8); 349 writeb(0x00, p + UART_EXAR_MPIOLVL_15_8); 350 writeb(0x00, p + UART_EXAR_MPIO3T_15_8); 351 writeb(0x00, p + UART_EXAR_MPIOINV_15_8); 352 writeb(dir, p + UART_EXAR_MPIOSEL_15_8); 353 writeb(0x00, p + UART_EXAR_MPIOOD_15_8); 354 } 355 356 static struct platform_device *__xr17v35x_register_gpio(struct pci_dev *pcidev, 357 const struct software_node *node) 358 { 359 struct platform_device *pdev; 360 361 pdev = platform_device_alloc("gpio_exar", PLATFORM_DEVID_AUTO); 362 if (!pdev) 363 return NULL; 364 365 pdev->dev.parent = &pcidev->dev; 366 ACPI_COMPANION_SET(&pdev->dev, ACPI_COMPANION(&pcidev->dev)); 367 368 if (device_add_software_node(&pdev->dev, node) < 0 || 369 platform_device_add(pdev) < 0) { 370 platform_device_put(pdev); 371 return NULL; 372 } 373 374 return pdev; 375 } 376 377 static void __xr17v35x_unregister_gpio(struct platform_device *pdev) 378 { 379 device_remove_software_node(&pdev->dev); 380 platform_device_unregister(pdev); 381 } 382 383 static const struct property_entry exar_gpio_properties[] = { 384 PROPERTY_ENTRY_U32("exar,first-pin", 0), 385 PROPERTY_ENTRY_U32("ngpios", 16), 386 { } 387 }; 388 389 static const struct software_node exar_gpio_node = { 390 .properties = exar_gpio_properties, 391 }; 392 393 static int xr17v35x_register_gpio(struct pci_dev *pcidev, struct uart_8250_port *port) 394 { 395 if (pcidev->vendor == PCI_VENDOR_ID_EXAR) 396 port->port.private_data = 397 __xr17v35x_register_gpio(pcidev, &exar_gpio_node); 398 399 return 0; 400 } 401 402 static void xr17v35x_unregister_gpio(struct uart_8250_port *port) 403 { 404 if (!port->port.private_data) 405 return; 406 407 __xr17v35x_unregister_gpio(port->port.private_data); 408 port->port.private_data = NULL; 409 } 410 411 static int generic_rs485_config(struct uart_port *port, 412 struct serial_rs485 *rs485) 413 { 414 bool is_rs485 = !!(rs485->flags & SER_RS485_ENABLED); 415 u8 __iomem *p = port->membase; 416 u8 value; 417 418 value = readb(p + UART_EXAR_FCTR); 419 if (is_rs485) 420 value |= UART_FCTR_EXAR_485; 421 else 422 value &= ~UART_FCTR_EXAR_485; 423 424 writeb(value, p + UART_EXAR_FCTR); 425 426 if (is_rs485) 427 writeb(UART_EXAR_RS485_DLY(4), p + UART_MSR); 428 429 port->rs485 = *rs485; 430 431 return 0; 432 } 433 434 static const struct exar8250_platform exar8250_default_platform = { 435 .register_gpio = xr17v35x_register_gpio, 436 .unregister_gpio = xr17v35x_unregister_gpio, 437 .rs485_config = generic_rs485_config, 438 }; 439 440 static int iot2040_rs485_config(struct uart_port *port, 441 struct serial_rs485 *rs485) 442 { 443 bool is_rs485 = !!(rs485->flags & SER_RS485_ENABLED); 444 u8 __iomem *p = port->membase; 445 u8 mask = IOT2040_UART1_MASK; 446 u8 mode, value; 447 448 if (is_rs485) { 449 if (rs485->flags & SER_RS485_RX_DURING_TX) 450 mode = IOT2040_UART_MODE_RS422; 451 else 452 mode = IOT2040_UART_MODE_RS485; 453 454 if (rs485->flags & SER_RS485_TERMINATE_BUS) 455 mode |= IOT2040_UART_TERMINATE_BUS; 456 } else { 457 mode = IOT2040_UART_MODE_RS232; 458 } 459 460 if (port->line == 3) { 461 mask <<= IOT2040_UART2_SHIFT; 462 mode <<= IOT2040_UART2_SHIFT; 463 } 464 465 value = readb(p + UART_EXAR_MPIOLVL_7_0); 466 value &= ~mask; 467 value |= mode; 468 writeb(value, p + UART_EXAR_MPIOLVL_7_0); 469 470 return generic_rs485_config(port, rs485); 471 } 472 473 static const struct property_entry iot2040_gpio_properties[] = { 474 PROPERTY_ENTRY_U32("exar,first-pin", 10), 475 PROPERTY_ENTRY_U32("ngpios", 1), 476 { } 477 }; 478 479 static const struct software_node iot2040_gpio_node = { 480 .properties = iot2040_gpio_properties, 481 }; 482 483 static int iot2040_register_gpio(struct pci_dev *pcidev, 484 struct uart_8250_port *port) 485 { 486 u8 __iomem *p = port->port.membase; 487 488 writeb(IOT2040_UARTS_DEFAULT_MODE, p + UART_EXAR_MPIOLVL_7_0); 489 writeb(IOT2040_UARTS_GPIO_LO_MODE, p + UART_EXAR_MPIOSEL_7_0); 490 writeb(IOT2040_UARTS_ENABLE, p + UART_EXAR_MPIOLVL_15_8); 491 writeb(IOT2040_UARTS_GPIO_HI_MODE, p + UART_EXAR_MPIOSEL_15_8); 492 493 port->port.private_data = 494 __xr17v35x_register_gpio(pcidev, &iot2040_gpio_node); 495 496 return 0; 497 } 498 499 static const struct exar8250_platform iot2040_platform = { 500 .rs485_config = iot2040_rs485_config, 501 .register_gpio = iot2040_register_gpio, 502 .unregister_gpio = xr17v35x_unregister_gpio, 503 }; 504 505 /* 506 * For SIMATIC IOT2000, only IOT2040 and its variants have the Exar device, 507 * IOT2020 doesn't have. Therefore it is sufficient to match on the common 508 * board name after the device was found. 509 */ 510 static const struct dmi_system_id exar_platforms[] = { 511 { 512 .matches = { 513 DMI_EXACT_MATCH(DMI_BOARD_NAME, "SIMATIC IOT2000"), 514 }, 515 .driver_data = (void *)&iot2040_platform, 516 }, 517 {} 518 }; 519 520 static const struct exar8250_platform *exar_get_platform(void) 521 { 522 const struct dmi_system_id *dmi_match; 523 524 dmi_match = dmi_first_match(exar_platforms); 525 if (dmi_match) 526 return dmi_match->driver_data; 527 528 return &exar8250_default_platform; 529 } 530 531 static int 532 pci_xr17v35x_setup(struct exar8250 *priv, struct pci_dev *pcidev, 533 struct uart_8250_port *port, int idx) 534 { 535 const struct exar8250_platform *platform = exar_get_platform(); 536 unsigned int offset = idx * 0x400; 537 unsigned int baud = 7812500; 538 u8 __iomem *p; 539 int ret; 540 541 port->port.uartclk = baud * 16; 542 port->port.rs485_config = platform->rs485_config; 543 544 /* 545 * Setup the UART clock for the devices on expansion slot to 546 * half the clock speed of the main chip (which is 125MHz) 547 */ 548 if (idx >= 8) 549 port->port.uartclk /= 2; 550 551 ret = default_setup(priv, pcidev, idx, offset, port); 552 if (ret) 553 return ret; 554 555 p = port->port.membase; 556 557 writeb(0x00, p + UART_EXAR_8XMODE); 558 writeb(UART_FCTR_EXAR_TRGD, p + UART_EXAR_FCTR); 559 writeb(128, p + UART_EXAR_TXTRG); 560 writeb(128, p + UART_EXAR_RXTRG); 561 562 if (idx == 0) { 563 /* Setup Multipurpose Input/Output pins. */ 564 setup_gpio(pcidev, p); 565 566 ret = platform->register_gpio(pcidev, port); 567 } 568 569 return ret; 570 } 571 572 static void pci_xr17v35x_exit(struct pci_dev *pcidev) 573 { 574 const struct exar8250_platform *platform = exar_get_platform(); 575 struct exar8250 *priv = pci_get_drvdata(pcidev); 576 struct uart_8250_port *port = serial8250_get_port(priv->line[0]); 577 578 platform->unregister_gpio(port); 579 } 580 581 static inline void exar_misc_clear(struct exar8250 *priv) 582 { 583 /* Clear all PCI interrupts by reading INT0. No effect on IIR */ 584 readb(priv->virt + UART_EXAR_INT0); 585 586 /* Clear INT0 for Expansion Interface slave ports, too */ 587 if (priv->board->num_ports > 8) 588 readb(priv->virt + 0x2000 + UART_EXAR_INT0); 589 } 590 591 /* 592 * These Exar UARTs have an extra interrupt indicator that could fire for a 593 * few interrupts that are not presented/cleared through IIR. One of which is 594 * a wakeup interrupt when coming out of sleep. These interrupts are only 595 * cleared by reading global INT0 or INT1 registers as interrupts are 596 * associated with channel 0. The INT[3:0] registers _are_ accessible from each 597 * channel's address space, but for the sake of bus efficiency we register a 598 * dedicated handler at the PCI device level to handle them. 599 */ 600 static irqreturn_t exar_misc_handler(int irq, void *data) 601 { 602 exar_misc_clear(data); 603 604 return IRQ_HANDLED; 605 } 606 607 static int 608 exar_pci_probe(struct pci_dev *pcidev, const struct pci_device_id *ent) 609 { 610 unsigned int nr_ports, i, bar = 0, maxnr; 611 struct exar8250_board *board; 612 struct uart_8250_port uart; 613 struct exar8250 *priv; 614 int rc; 615 616 board = (struct exar8250_board *)ent->driver_data; 617 if (!board) 618 return -EINVAL; 619 620 rc = pcim_enable_device(pcidev); 621 if (rc) 622 return rc; 623 624 maxnr = pci_resource_len(pcidev, bar) >> (board->reg_shift + 3); 625 626 if (pcidev->vendor == PCI_VENDOR_ID_ACCESSIO) 627 nr_ports = BIT(((pcidev->device & 0x38) >> 3) - 1); 628 else if (board->num_ports) 629 nr_ports = board->num_ports; 630 else 631 nr_ports = pcidev->device & 0x0f; 632 633 priv = devm_kzalloc(&pcidev->dev, struct_size(priv, line, nr_ports), GFP_KERNEL); 634 if (!priv) 635 return -ENOMEM; 636 637 priv->board = board; 638 priv->virt = pcim_iomap(pcidev, bar, 0); 639 if (!priv->virt) 640 return -ENOMEM; 641 642 pci_set_master(pcidev); 643 644 rc = pci_alloc_irq_vectors(pcidev, 1, 1, PCI_IRQ_ALL_TYPES); 645 if (rc < 0) 646 return rc; 647 648 memset(&uart, 0, sizeof(uart)); 649 uart.port.flags = UPF_SHARE_IRQ | UPF_EXAR_EFR | UPF_FIXED_TYPE | UPF_FIXED_PORT; 650 uart.port.irq = pci_irq_vector(pcidev, 0); 651 uart.port.dev = &pcidev->dev; 652 653 rc = devm_request_irq(&pcidev->dev, uart.port.irq, exar_misc_handler, 654 IRQF_SHARED, "exar_uart", priv); 655 if (rc) 656 return rc; 657 658 /* Clear interrupts */ 659 exar_misc_clear(priv); 660 661 for (i = 0; i < nr_ports && i < maxnr; i++) { 662 rc = board->setup(priv, pcidev, &uart, i); 663 if (rc) { 664 dev_err(&pcidev->dev, "Failed to setup port %u\n", i); 665 break; 666 } 667 668 dev_dbg(&pcidev->dev, "Setup PCI port: port %lx, irq %d, type %d\n", 669 uart.port.iobase, uart.port.irq, uart.port.iotype); 670 671 priv->line[i] = serial8250_register_8250_port(&uart); 672 if (priv->line[i] < 0) { 673 dev_err(&pcidev->dev, 674 "Couldn't register serial port %lx, irq %d, type %d, error %d\n", 675 uart.port.iobase, uart.port.irq, 676 uart.port.iotype, priv->line[i]); 677 break; 678 } 679 } 680 priv->nr = i; 681 pci_set_drvdata(pcidev, priv); 682 return 0; 683 } 684 685 static void exar_pci_remove(struct pci_dev *pcidev) 686 { 687 struct exar8250 *priv = pci_get_drvdata(pcidev); 688 unsigned int i; 689 690 for (i = 0; i < priv->nr; i++) 691 serial8250_unregister_port(priv->line[i]); 692 693 if (priv->board->exit) 694 priv->board->exit(pcidev); 695 } 696 697 static int __maybe_unused exar_suspend(struct device *dev) 698 { 699 struct pci_dev *pcidev = to_pci_dev(dev); 700 struct exar8250 *priv = pci_get_drvdata(pcidev); 701 unsigned int i; 702 703 for (i = 0; i < priv->nr; i++) 704 if (priv->line[i] >= 0) 705 serial8250_suspend_port(priv->line[i]); 706 707 /* Ensure that every init quirk is properly torn down */ 708 if (priv->board->exit) 709 priv->board->exit(pcidev); 710 711 return 0; 712 } 713 714 static int __maybe_unused exar_resume(struct device *dev) 715 { 716 struct exar8250 *priv = dev_get_drvdata(dev); 717 unsigned int i; 718 719 exar_misc_clear(priv); 720 721 for (i = 0; i < priv->nr; i++) 722 if (priv->line[i] >= 0) 723 serial8250_resume_port(priv->line[i]); 724 725 return 0; 726 } 727 728 static SIMPLE_DEV_PM_OPS(exar_pci_pm, exar_suspend, exar_resume); 729 730 static const struct exar8250_board pbn_fastcom335_2 = { 731 .num_ports = 2, 732 .setup = pci_fastcom335_setup, 733 }; 734 735 static const struct exar8250_board pbn_fastcom335_4 = { 736 .num_ports = 4, 737 .setup = pci_fastcom335_setup, 738 }; 739 740 static const struct exar8250_board pbn_fastcom335_8 = { 741 .num_ports = 8, 742 .setup = pci_fastcom335_setup, 743 }; 744 745 static const struct exar8250_board pbn_connect = { 746 .setup = pci_connect_tech_setup, 747 }; 748 749 static const struct exar8250_board pbn_exar_ibm_saturn = { 750 .num_ports = 1, 751 .setup = pci_xr17c154_setup, 752 }; 753 754 static const struct exar8250_board pbn_exar_XR17C15x = { 755 .setup = pci_xr17c154_setup, 756 }; 757 758 static const struct exar8250_board pbn_exar_XR17V35x = { 759 .setup = pci_xr17v35x_setup, 760 .exit = pci_xr17v35x_exit, 761 }; 762 763 static const struct exar8250_board pbn_fastcom35x_2 = { 764 .num_ports = 2, 765 .setup = pci_xr17v35x_setup, 766 .exit = pci_xr17v35x_exit, 767 }; 768 769 static const struct exar8250_board pbn_fastcom35x_4 = { 770 .num_ports = 4, 771 .setup = pci_xr17v35x_setup, 772 .exit = pci_xr17v35x_exit, 773 }; 774 775 static const struct exar8250_board pbn_fastcom35x_8 = { 776 .num_ports = 8, 777 .setup = pci_xr17v35x_setup, 778 .exit = pci_xr17v35x_exit, 779 }; 780 781 static const struct exar8250_board pbn_exar_XR17V4358 = { 782 .num_ports = 12, 783 .setup = pci_xr17v35x_setup, 784 .exit = pci_xr17v35x_exit, 785 }; 786 787 static const struct exar8250_board pbn_exar_XR17V8358 = { 788 .num_ports = 16, 789 .setup = pci_xr17v35x_setup, 790 .exit = pci_xr17v35x_exit, 791 }; 792 793 #define CONNECT_DEVICE(devid, sdevid, bd) { \ 794 PCI_DEVICE_SUB( \ 795 PCI_VENDOR_ID_EXAR, \ 796 PCI_DEVICE_ID_EXAR_##devid, \ 797 PCI_SUBVENDOR_ID_CONNECT_TECH, \ 798 PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_##sdevid), 0, 0, \ 799 (kernel_ulong_t)&bd \ 800 } 801 802 #define EXAR_DEVICE(vend, devid, bd) { PCI_DEVICE_DATA(vend, devid, &bd) } 803 804 #define IBM_DEVICE(devid, sdevid, bd) { \ 805 PCI_DEVICE_SUB( \ 806 PCI_VENDOR_ID_EXAR, \ 807 PCI_DEVICE_ID_EXAR_##devid, \ 808 PCI_VENDOR_ID_IBM, \ 809 PCI_SUBDEVICE_ID_IBM_##sdevid), 0, 0, \ 810 (kernel_ulong_t)&bd \ 811 } 812 813 static const struct pci_device_id exar_pci_tbl[] = { 814 EXAR_DEVICE(ACCESSIO, COM_2S, pbn_exar_XR17C15x), 815 EXAR_DEVICE(ACCESSIO, COM_4S, pbn_exar_XR17C15x), 816 EXAR_DEVICE(ACCESSIO, COM_8S, pbn_exar_XR17C15x), 817 EXAR_DEVICE(ACCESSIO, COM232_8, pbn_exar_XR17C15x), 818 EXAR_DEVICE(ACCESSIO, COM_2SM, pbn_exar_XR17C15x), 819 EXAR_DEVICE(ACCESSIO, COM_4SM, pbn_exar_XR17C15x), 820 EXAR_DEVICE(ACCESSIO, COM_8SM, pbn_exar_XR17C15x), 821 822 CONNECT_DEVICE(XR17C152, UART_2_232, pbn_connect), 823 CONNECT_DEVICE(XR17C154, UART_4_232, pbn_connect), 824 CONNECT_DEVICE(XR17C158, UART_8_232, pbn_connect), 825 CONNECT_DEVICE(XR17C152, UART_1_1, pbn_connect), 826 CONNECT_DEVICE(XR17C154, UART_2_2, pbn_connect), 827 CONNECT_DEVICE(XR17C158, UART_4_4, pbn_connect), 828 CONNECT_DEVICE(XR17C152, UART_2, pbn_connect), 829 CONNECT_DEVICE(XR17C154, UART_4, pbn_connect), 830 CONNECT_DEVICE(XR17C158, UART_8, pbn_connect), 831 CONNECT_DEVICE(XR17C152, UART_2_485, pbn_connect), 832 CONNECT_DEVICE(XR17C154, UART_4_485, pbn_connect), 833 CONNECT_DEVICE(XR17C158, UART_8_485, pbn_connect), 834 835 IBM_DEVICE(XR17C152, SATURN_SERIAL_ONE_PORT, pbn_exar_ibm_saturn), 836 837 /* Exar Corp. XR17C15[248] Dual/Quad/Octal UART */ 838 EXAR_DEVICE(EXAR, XR17C152, pbn_exar_XR17C15x), 839 EXAR_DEVICE(EXAR, XR17C154, pbn_exar_XR17C15x), 840 EXAR_DEVICE(EXAR, XR17C158, pbn_exar_XR17C15x), 841 842 /* Exar Corp. XR17V[48]35[248] Dual/Quad/Octal/Hexa PCIe UARTs */ 843 EXAR_DEVICE(EXAR, XR17V352, pbn_exar_XR17V35x), 844 EXAR_DEVICE(EXAR, XR17V354, pbn_exar_XR17V35x), 845 EXAR_DEVICE(EXAR, XR17V358, pbn_exar_XR17V35x), 846 EXAR_DEVICE(EXAR, XR17V4358, pbn_exar_XR17V4358), 847 EXAR_DEVICE(EXAR, XR17V8358, pbn_exar_XR17V8358), 848 EXAR_DEVICE(COMMTECH, 4222PCIE, pbn_fastcom35x_2), 849 EXAR_DEVICE(COMMTECH, 4224PCIE, pbn_fastcom35x_4), 850 EXAR_DEVICE(COMMTECH, 4228PCIE, pbn_fastcom35x_8), 851 852 EXAR_DEVICE(COMMTECH, 4222PCI335, pbn_fastcom335_2), 853 EXAR_DEVICE(COMMTECH, 4224PCI335, pbn_fastcom335_4), 854 EXAR_DEVICE(COMMTECH, 2324PCI335, pbn_fastcom335_4), 855 EXAR_DEVICE(COMMTECH, 2328PCI335, pbn_fastcom335_8), 856 { 0, } 857 }; 858 MODULE_DEVICE_TABLE(pci, exar_pci_tbl); 859 860 static struct pci_driver exar_pci_driver = { 861 .name = "exar_serial", 862 .probe = exar_pci_probe, 863 .remove = exar_pci_remove, 864 .driver = { 865 .pm = &exar_pci_pm, 866 }, 867 .id_table = exar_pci_tbl, 868 }; 869 module_pci_driver(exar_pci_driver); 870 871 MODULE_LICENSE("GPL"); 872 MODULE_DESCRIPTION("Exar Serial Driver"); 873 MODULE_AUTHOR("Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>"); 874