1 // SPDX-License-Identifier: GPL-2.0-only 2 /* Copyright (c) 2020, Broadcom */ 3 /* 4 * 8250-core based driver for Broadcom ns16550a UARTs 5 * 6 * This driver uses the standard 8250 driver core but adds additional 7 * optional features including the ability to use a baud rate clock 8 * mux for more accurate high speed baud rate selection and also 9 * an optional DMA engine. 10 * 11 */ 12 13 #include <linux/module.h> 14 #include <linux/types.h> 15 #include <linux/tty.h> 16 #include <linux/errno.h> 17 #include <linux/device.h> 18 #include <linux/io.h> 19 #include <linux/of.h> 20 #include <linux/dma-mapping.h> 21 #include <linux/tty_flip.h> 22 #include <linux/delay.h> 23 #include <linux/clk.h> 24 #include <linux/debugfs.h> 25 26 #include "8250.h" 27 28 /* Register definitions for UART DMA block. Version 1.1 or later. */ 29 #define UDMA_ARB_RX 0x00 30 #define UDMA_ARB_TX 0x04 31 #define UDMA_ARB_REQ 0x00000001 32 #define UDMA_ARB_GRANT 0x00000002 33 34 #define UDMA_RX_REVISION 0x00 35 #define UDMA_RX_REVISION_REQUIRED 0x00000101 36 #define UDMA_RX_CTRL 0x04 37 #define UDMA_RX_CTRL_BUF_CLOSE_MODE 0x00010000 38 #define UDMA_RX_CTRL_MASK_WR_DONE 0x00008000 39 #define UDMA_RX_CTRL_ENDIAN_OVERRIDE 0x00004000 40 #define UDMA_RX_CTRL_ENDIAN 0x00002000 41 #define UDMA_RX_CTRL_OE_IS_ERR 0x00001000 42 #define UDMA_RX_CTRL_PE_IS_ERR 0x00000800 43 #define UDMA_RX_CTRL_FE_IS_ERR 0x00000400 44 #define UDMA_RX_CTRL_NUM_BUF_USED_MASK 0x000003c0 45 #define UDMA_RX_CTRL_NUM_BUF_USED_SHIFT 6 46 #define UDMA_RX_CTRL_BUF_CLOSE_CLK_SEL_SYS 0x00000020 47 #define UDMA_RX_CTRL_BUF_CLOSE_ENA 0x00000010 48 #define UDMA_RX_CTRL_TIMEOUT_CLK_SEL_SYS 0x00000008 49 #define UDMA_RX_CTRL_TIMEOUT_ENA 0x00000004 50 #define UDMA_RX_CTRL_ABORT 0x00000002 51 #define UDMA_RX_CTRL_ENA 0x00000001 52 #define UDMA_RX_STATUS 0x08 53 #define UDMA_RX_STATUS_ACTIVE_BUF_MASK 0x0000000f 54 #define UDMA_RX_TRANSFER_LEN 0x0c 55 #define UDMA_RX_TRANSFER_TOTAL 0x10 56 #define UDMA_RX_BUFFER_SIZE 0x14 57 #define UDMA_RX_SRC_ADDR 0x18 58 #define UDMA_RX_TIMEOUT 0x1c 59 #define UDMA_RX_BUFFER_CLOSE 0x20 60 #define UDMA_RX_BLOCKOUT_COUNTER 0x24 61 #define UDMA_RX_BUF0_PTR_LO 0x28 62 #define UDMA_RX_BUF0_PTR_HI 0x2c 63 #define UDMA_RX_BUF0_STATUS 0x30 64 #define UDMA_RX_BUFX_STATUS_OVERRUN_ERR 0x00000010 65 #define UDMA_RX_BUFX_STATUS_FRAME_ERR 0x00000008 66 #define UDMA_RX_BUFX_STATUS_PARITY_ERR 0x00000004 67 #define UDMA_RX_BUFX_STATUS_CLOSE_EXPIRED 0x00000002 68 #define UDMA_RX_BUFX_STATUS_DATA_RDY 0x00000001 69 #define UDMA_RX_BUF0_DATA_LEN 0x34 70 #define UDMA_RX_BUF1_PTR_LO 0x38 71 #define UDMA_RX_BUF1_PTR_HI 0x3c 72 #define UDMA_RX_BUF1_STATUS 0x40 73 #define UDMA_RX_BUF1_DATA_LEN 0x44 74 75 #define UDMA_TX_REVISION 0x00 76 #define UDMA_TX_REVISION_REQUIRED 0x00000101 77 #define UDMA_TX_CTRL 0x04 78 #define UDMA_TX_CTRL_ENDIAN_OVERRIDE 0x00000080 79 #define UDMA_TX_CTRL_ENDIAN 0x00000040 80 #define UDMA_TX_CTRL_NUM_BUF_USED_MASK 0x00000030 81 #define UDMA_TX_CTRL_NUM_BUF_USED_1 0x00000010 82 #define UDMA_TX_CTRL_ABORT 0x00000002 83 #define UDMA_TX_CTRL_ENA 0x00000001 84 #define UDMA_TX_DST_ADDR 0x08 85 #define UDMA_TX_BLOCKOUT_COUNTER 0x10 86 #define UDMA_TX_TRANSFER_LEN 0x14 87 #define UDMA_TX_TRANSFER_TOTAL 0x18 88 #define UDMA_TX_STATUS 0x20 89 #define UDMA_TX_BUF0_PTR_LO 0x24 90 #define UDMA_TX_BUF0_PTR_HI 0x28 91 #define UDMA_TX_BUF0_STATUS 0x2c 92 #define UDMA_TX_BUFX_LAST 0x00000002 93 #define UDMA_TX_BUFX_EMPTY 0x00000001 94 #define UDMA_TX_BUF0_DATA_LEN 0x30 95 #define UDMA_TX_BUF0_DATA_SENT 0x34 96 #define UDMA_TX_BUF1_PTR_LO 0x38 97 98 #define UDMA_INTR_STATUS 0x00 99 #define UDMA_INTR_ARB_TX_GRANT 0x00040000 100 #define UDMA_INTR_ARB_RX_GRANT 0x00020000 101 #define UDMA_INTR_TX_ALL_EMPTY 0x00010000 102 #define UDMA_INTR_TX_EMPTY_BUF1 0x00008000 103 #define UDMA_INTR_TX_EMPTY_BUF0 0x00004000 104 #define UDMA_INTR_TX_ABORT 0x00002000 105 #define UDMA_INTR_TX_DONE 0x00001000 106 #define UDMA_INTR_RX_ERROR 0x00000800 107 #define UDMA_INTR_RX_TIMEOUT 0x00000400 108 #define UDMA_INTR_RX_READY_BUF7 0x00000200 109 #define UDMA_INTR_RX_READY_BUF6 0x00000100 110 #define UDMA_INTR_RX_READY_BUF5 0x00000080 111 #define UDMA_INTR_RX_READY_BUF4 0x00000040 112 #define UDMA_INTR_RX_READY_BUF3 0x00000020 113 #define UDMA_INTR_RX_READY_BUF2 0x00000010 114 #define UDMA_INTR_RX_READY_BUF1 0x00000008 115 #define UDMA_INTR_RX_READY_BUF0 0x00000004 116 #define UDMA_INTR_RX_READY_MASK 0x000003fc 117 #define UDMA_INTR_RX_READY_SHIFT 2 118 #define UDMA_INTR_RX_ABORT 0x00000002 119 #define UDMA_INTR_RX_DONE 0x00000001 120 #define UDMA_INTR_SET 0x04 121 #define UDMA_INTR_CLEAR 0x08 122 #define UDMA_INTR_MASK_STATUS 0x0c 123 #define UDMA_INTR_MASK_SET 0x10 124 #define UDMA_INTR_MASK_CLEAR 0x14 125 126 127 #define UDMA_RX_INTERRUPTS ( \ 128 UDMA_INTR_RX_ERROR | \ 129 UDMA_INTR_RX_TIMEOUT | \ 130 UDMA_INTR_RX_READY_BUF0 | \ 131 UDMA_INTR_RX_READY_BUF1 | \ 132 UDMA_INTR_RX_READY_BUF2 | \ 133 UDMA_INTR_RX_READY_BUF3 | \ 134 UDMA_INTR_RX_READY_BUF4 | \ 135 UDMA_INTR_RX_READY_BUF5 | \ 136 UDMA_INTR_RX_READY_BUF6 | \ 137 UDMA_INTR_RX_READY_BUF7 | \ 138 UDMA_INTR_RX_ABORT | \ 139 UDMA_INTR_RX_DONE) 140 141 #define UDMA_RX_ERR_INTERRUPTS ( \ 142 UDMA_INTR_RX_ERROR | \ 143 UDMA_INTR_RX_TIMEOUT | \ 144 UDMA_INTR_RX_ABORT | \ 145 UDMA_INTR_RX_DONE) 146 147 #define UDMA_TX_INTERRUPTS ( \ 148 UDMA_INTR_TX_ABORT | \ 149 UDMA_INTR_TX_DONE) 150 151 #define UDMA_IS_RX_INTERRUPT(status) ((status) & UDMA_RX_INTERRUPTS) 152 #define UDMA_IS_TX_INTERRUPT(status) ((status) & UDMA_TX_INTERRUPTS) 153 154 155 /* Current devices have 8 sets of RX buffer registers */ 156 #define UDMA_RX_BUFS_COUNT 8 157 #define UDMA_RX_BUFS_REG_OFFSET (UDMA_RX_BUF1_PTR_LO - UDMA_RX_BUF0_PTR_LO) 158 #define UDMA_RX_BUFx_PTR_LO(x) (UDMA_RX_BUF0_PTR_LO + \ 159 ((x) * UDMA_RX_BUFS_REG_OFFSET)) 160 #define UDMA_RX_BUFx_PTR_HI(x) (UDMA_RX_BUF0_PTR_HI + \ 161 ((x) * UDMA_RX_BUFS_REG_OFFSET)) 162 #define UDMA_RX_BUFx_STATUS(x) (UDMA_RX_BUF0_STATUS + \ 163 ((x) * UDMA_RX_BUFS_REG_OFFSET)) 164 #define UDMA_RX_BUFx_DATA_LEN(x) (UDMA_RX_BUF0_DATA_LEN + \ 165 ((x) * UDMA_RX_BUFS_REG_OFFSET)) 166 167 /* Current devices have 2 sets of TX buffer registers */ 168 #define UDMA_TX_BUFS_COUNT 2 169 #define UDMA_TX_BUFS_REG_OFFSET (UDMA_TX_BUF1_PTR_LO - UDMA_TX_BUF0_PTR_LO) 170 #define UDMA_TX_BUFx_PTR_LO(x) (UDMA_TX_BUF0_PTR_LO + \ 171 ((x) * UDMA_TX_BUFS_REG_OFFSET)) 172 #define UDMA_TX_BUFx_PTR_HI(x) (UDMA_TX_BUF0_PTR_HI + \ 173 ((x) * UDMA_TX_BUFS_REG_OFFSET)) 174 #define UDMA_TX_BUFx_STATUS(x) (UDMA_TX_BUF0_STATUS + \ 175 ((x) * UDMA_TX_BUFS_REG_OFFSET)) 176 #define UDMA_TX_BUFx_DATA_LEN(x) (UDMA_TX_BUF0_DATA_LEN + \ 177 ((x) * UDMA_TX_BUFS_REG_OFFSET)) 178 #define UDMA_TX_BUFx_DATA_SENT(x) (UDMA_TX_BUF0_DATA_SENT + \ 179 ((x) * UDMA_TX_BUFS_REG_OFFSET)) 180 #define REGS_8250 0 181 #define REGS_DMA_RX 1 182 #define REGS_DMA_TX 2 183 #define REGS_DMA_ISR 3 184 #define REGS_DMA_ARB 4 185 #define REGS_MAX 5 186 187 #define TX_BUF_SIZE 4096 188 #define RX_BUF_SIZE 4096 189 #define RX_BUFS_COUNT 2 190 #define KHZ 1000 191 #define MHZ(x) ((x) * KHZ * KHZ) 192 193 static const u32 brcmstb_rate_table[] = { 194 MHZ(81), 195 MHZ(108), 196 MHZ(64), /* Actually 64285715 for some chips */ 197 MHZ(48), 198 }; 199 200 static const u32 brcmstb_rate_table_7278[] = { 201 MHZ(81), 202 MHZ(108), 203 0, 204 MHZ(48), 205 }; 206 207 struct brcmuart_priv { 208 int line; 209 struct clk *baud_mux_clk; 210 unsigned long default_mux_rate; 211 u32 real_rates[ARRAY_SIZE(brcmstb_rate_table)]; 212 const u32 *rate_table; 213 ktime_t char_wait; 214 struct uart_port *up; 215 struct hrtimer hrt; 216 bool shutdown; 217 bool dma_enabled; 218 struct uart_8250_dma dma; 219 void __iomem *regs[REGS_MAX]; 220 dma_addr_t rx_addr; 221 void *rx_bufs; 222 size_t rx_size; 223 int rx_next_buf; 224 dma_addr_t tx_addr; 225 void *tx_buf; 226 size_t tx_size; 227 bool tx_running; 228 bool rx_running; 229 struct dentry *debugfs_dir; 230 231 /* stats exposed through debugfs */ 232 u64 dma_rx_partial_buf; 233 u64 dma_rx_full_buf; 234 u32 rx_bad_timeout_late_char; 235 u32 rx_bad_timeout_no_char; 236 u32 rx_missing_close_timeout; 237 u32 rx_err; 238 u32 rx_timeout; 239 u32 rx_abort; 240 u32 saved_mctrl; 241 }; 242 243 static struct dentry *brcmuart_debugfs_root; 244 245 /* 246 * Register access routines 247 */ 248 static u32 udma_readl(struct brcmuart_priv *priv, 249 int reg_type, int offset) 250 { 251 return readl(priv->regs[reg_type] + offset); 252 } 253 254 static void udma_writel(struct brcmuart_priv *priv, 255 int reg_type, int offset, u32 value) 256 { 257 writel(value, priv->regs[reg_type] + offset); 258 } 259 260 static void udma_set(struct brcmuart_priv *priv, 261 int reg_type, int offset, u32 bits) 262 { 263 void __iomem *reg = priv->regs[reg_type] + offset; 264 u32 value; 265 266 value = readl(reg); 267 value |= bits; 268 writel(value, reg); 269 } 270 271 static void udma_unset(struct brcmuart_priv *priv, 272 int reg_type, int offset, u32 bits) 273 { 274 void __iomem *reg = priv->regs[reg_type] + offset; 275 u32 value; 276 277 value = readl(reg); 278 value &= ~bits; 279 writel(value, reg); 280 } 281 282 /* 283 * The UART DMA engine hardware can be used by multiple UARTS, but 284 * only one at a time. Sharing is not currently supported so 285 * the first UART to request the DMA engine will get it and any 286 * subsequent requests by other UARTS will fail. 287 */ 288 static int brcmuart_arbitration(struct brcmuart_priv *priv, bool acquire) 289 { 290 u32 rx_grant; 291 u32 tx_grant; 292 int waits; 293 int ret = 0; 294 295 if (acquire) { 296 udma_set(priv, REGS_DMA_ARB, UDMA_ARB_RX, UDMA_ARB_REQ); 297 udma_set(priv, REGS_DMA_ARB, UDMA_ARB_TX, UDMA_ARB_REQ); 298 299 waits = 1; 300 while (1) { 301 rx_grant = udma_readl(priv, REGS_DMA_ARB, UDMA_ARB_RX); 302 tx_grant = udma_readl(priv, REGS_DMA_ARB, UDMA_ARB_TX); 303 if (rx_grant & tx_grant & UDMA_ARB_GRANT) 304 return 0; 305 if (waits-- == 0) 306 break; 307 msleep(1); 308 } 309 ret = 1; 310 } 311 312 udma_unset(priv, REGS_DMA_ARB, UDMA_ARB_RX, UDMA_ARB_REQ); 313 udma_unset(priv, REGS_DMA_ARB, UDMA_ARB_TX, UDMA_ARB_REQ); 314 return ret; 315 } 316 317 static void brcmuart_init_dma_hardware(struct brcmuart_priv *priv) 318 { 319 u32 daddr; 320 u32 value; 321 int x; 322 323 /* Start with all interrupts disabled */ 324 udma_writel(priv, REGS_DMA_ISR, UDMA_INTR_MASK_SET, 0xffffffff); 325 326 udma_writel(priv, REGS_DMA_RX, UDMA_RX_BUFFER_SIZE, RX_BUF_SIZE); 327 328 /* 329 * Setup buffer close to happen when 32 character times have 330 * elapsed since the last character was received. 331 */ 332 udma_writel(priv, REGS_DMA_RX, UDMA_RX_BUFFER_CLOSE, 16*10*32); 333 value = (RX_BUFS_COUNT << UDMA_RX_CTRL_NUM_BUF_USED_SHIFT) 334 | UDMA_RX_CTRL_BUF_CLOSE_MODE 335 | UDMA_RX_CTRL_BUF_CLOSE_ENA; 336 udma_writel(priv, REGS_DMA_RX, UDMA_RX_CTRL, value); 337 338 udma_writel(priv, REGS_DMA_RX, UDMA_RX_BLOCKOUT_COUNTER, 0); 339 daddr = priv->rx_addr; 340 for (x = 0; x < RX_BUFS_COUNT; x++) { 341 342 /* Set RX transfer length to 0 for unknown */ 343 udma_writel(priv, REGS_DMA_RX, UDMA_RX_TRANSFER_LEN, 0); 344 345 udma_writel(priv, REGS_DMA_RX, UDMA_RX_BUFx_PTR_LO(x), 346 lower_32_bits(daddr)); 347 udma_writel(priv, REGS_DMA_RX, UDMA_RX_BUFx_PTR_HI(x), 348 upper_32_bits(daddr)); 349 daddr += RX_BUF_SIZE; 350 } 351 352 daddr = priv->tx_addr; 353 udma_writel(priv, REGS_DMA_TX, UDMA_TX_BUFx_PTR_LO(0), 354 lower_32_bits(daddr)); 355 udma_writel(priv, REGS_DMA_TX, UDMA_TX_BUFx_PTR_HI(0), 356 upper_32_bits(daddr)); 357 udma_writel(priv, REGS_DMA_TX, UDMA_TX_CTRL, 358 UDMA_TX_CTRL_NUM_BUF_USED_1); 359 360 /* clear all interrupts then enable them */ 361 udma_writel(priv, REGS_DMA_ISR, UDMA_INTR_CLEAR, 0xffffffff); 362 udma_writel(priv, REGS_DMA_ISR, UDMA_INTR_MASK_CLEAR, 363 UDMA_RX_INTERRUPTS | UDMA_TX_INTERRUPTS); 364 365 } 366 367 static void start_rx_dma(struct uart_8250_port *p) 368 { 369 struct brcmuart_priv *priv = p->port.private_data; 370 int x; 371 372 udma_unset(priv, REGS_DMA_RX, UDMA_RX_CTRL, UDMA_RX_CTRL_ENA); 373 374 /* Clear the RX ready bit for all buffers */ 375 for (x = 0; x < RX_BUFS_COUNT; x++) 376 udma_unset(priv, REGS_DMA_RX, UDMA_RX_BUFx_STATUS(x), 377 UDMA_RX_BUFX_STATUS_DATA_RDY); 378 379 /* always start with buffer 0 */ 380 udma_unset(priv, REGS_DMA_RX, UDMA_RX_STATUS, 381 UDMA_RX_STATUS_ACTIVE_BUF_MASK); 382 priv->rx_next_buf = 0; 383 384 udma_set(priv, REGS_DMA_RX, UDMA_RX_CTRL, UDMA_RX_CTRL_ENA); 385 priv->rx_running = true; 386 } 387 388 static void stop_rx_dma(struct uart_8250_port *p) 389 { 390 struct brcmuart_priv *priv = p->port.private_data; 391 392 /* If RX is running, set the RX ABORT */ 393 if (priv->rx_running) 394 udma_set(priv, REGS_DMA_RX, UDMA_RX_CTRL, UDMA_RX_CTRL_ABORT); 395 } 396 397 static int stop_tx_dma(struct uart_8250_port *p) 398 { 399 struct brcmuart_priv *priv = p->port.private_data; 400 u32 value; 401 402 /* If TX is running, set the TX ABORT */ 403 value = udma_readl(priv, REGS_DMA_TX, UDMA_TX_CTRL); 404 if (value & UDMA_TX_CTRL_ENA) 405 udma_set(priv, REGS_DMA_TX, UDMA_TX_CTRL, UDMA_TX_CTRL_ABORT); 406 priv->tx_running = false; 407 return 0; 408 } 409 410 /* 411 * NOTE: printk's in this routine will hang the system if this is 412 * the console tty 413 */ 414 static int brcmuart_tx_dma(struct uart_8250_port *p) 415 { 416 struct brcmuart_priv *priv = p->port.private_data; 417 struct circ_buf *xmit = &p->port.state->xmit; 418 u32 tx_size; 419 420 if (uart_tx_stopped(&p->port) || priv->tx_running || 421 uart_circ_empty(xmit)) { 422 return 0; 423 } 424 tx_size = CIRC_CNT_TO_END(xmit->head, xmit->tail, UART_XMIT_SIZE); 425 426 priv->dma.tx_err = 0; 427 memcpy(priv->tx_buf, &xmit->buf[xmit->tail], tx_size); 428 xmit->tail += tx_size; 429 xmit->tail &= UART_XMIT_SIZE - 1; 430 p->port.icount.tx += tx_size; 431 432 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) 433 uart_write_wakeup(&p->port); 434 435 udma_writel(priv, REGS_DMA_TX, UDMA_TX_TRANSFER_LEN, tx_size); 436 udma_writel(priv, REGS_DMA_TX, UDMA_TX_BUF0_DATA_LEN, tx_size); 437 udma_unset(priv, REGS_DMA_TX, UDMA_TX_BUF0_STATUS, UDMA_TX_BUFX_EMPTY); 438 udma_set(priv, REGS_DMA_TX, UDMA_TX_CTRL, UDMA_TX_CTRL_ENA); 439 priv->tx_running = true; 440 441 return 0; 442 } 443 444 static void brcmuart_rx_buf_done_isr(struct uart_port *up, int index) 445 { 446 struct brcmuart_priv *priv = up->private_data; 447 struct tty_port *tty_port = &up->state->port; 448 u32 status; 449 u32 length; 450 u32 copied; 451 452 /* Make sure we're still in sync with the hardware */ 453 status = udma_readl(priv, REGS_DMA_RX, UDMA_RX_BUFx_STATUS(index)); 454 length = udma_readl(priv, REGS_DMA_RX, UDMA_RX_BUFx_DATA_LEN(index)); 455 456 if ((status & UDMA_RX_BUFX_STATUS_DATA_RDY) == 0) { 457 dev_err(up->dev, "RX done interrupt but DATA_RDY not found\n"); 458 return; 459 } 460 if (status & (UDMA_RX_BUFX_STATUS_OVERRUN_ERR | 461 UDMA_RX_BUFX_STATUS_FRAME_ERR | 462 UDMA_RX_BUFX_STATUS_PARITY_ERR)) { 463 if (status & UDMA_RX_BUFX_STATUS_OVERRUN_ERR) { 464 up->icount.overrun++; 465 dev_warn(up->dev, "RX OVERRUN Error\n"); 466 } 467 if (status & UDMA_RX_BUFX_STATUS_FRAME_ERR) { 468 up->icount.frame++; 469 dev_warn(up->dev, "RX FRAMING Error\n"); 470 } 471 if (status & UDMA_RX_BUFX_STATUS_PARITY_ERR) { 472 up->icount.parity++; 473 dev_warn(up->dev, "RX PARITY Error\n"); 474 } 475 } 476 copied = (u32)tty_insert_flip_string( 477 tty_port, 478 priv->rx_bufs + (index * RX_BUF_SIZE), 479 length); 480 if (copied != length) { 481 dev_warn(up->dev, "Flip buffer overrun of %d bytes\n", 482 length - copied); 483 up->icount.overrun += length - copied; 484 } 485 up->icount.rx += length; 486 if (status & UDMA_RX_BUFX_STATUS_CLOSE_EXPIRED) 487 priv->dma_rx_partial_buf++; 488 else if (length != RX_BUF_SIZE) 489 /* 490 * This is a bug in the controller that doesn't cause 491 * any problems but will be fixed in the future. 492 */ 493 priv->rx_missing_close_timeout++; 494 else 495 priv->dma_rx_full_buf++; 496 497 tty_flip_buffer_push(tty_port); 498 } 499 500 static void brcmuart_rx_isr(struct uart_port *up, u32 rx_isr) 501 { 502 struct brcmuart_priv *priv = up->private_data; 503 struct device *dev = up->dev; 504 u32 rx_done_isr; 505 u32 check_isr; 506 507 rx_done_isr = (rx_isr & UDMA_INTR_RX_READY_MASK); 508 while (rx_done_isr) { 509 check_isr = UDMA_INTR_RX_READY_BUF0 << priv->rx_next_buf; 510 if (check_isr & rx_done_isr) { 511 brcmuart_rx_buf_done_isr(up, priv->rx_next_buf); 512 } else { 513 dev_err(dev, 514 "RX buffer ready out of sequence, restarting RX DMA\n"); 515 start_rx_dma(up_to_u8250p(up)); 516 break; 517 } 518 if (rx_isr & UDMA_RX_ERR_INTERRUPTS) { 519 if (rx_isr & UDMA_INTR_RX_ERROR) 520 priv->rx_err++; 521 if (rx_isr & UDMA_INTR_RX_TIMEOUT) { 522 priv->rx_timeout++; 523 dev_err(dev, "RX TIMEOUT Error\n"); 524 } 525 if (rx_isr & UDMA_INTR_RX_ABORT) 526 priv->rx_abort++; 527 priv->rx_running = false; 528 } 529 /* If not ABORT, re-enable RX buffer */ 530 if (!(rx_isr & UDMA_INTR_RX_ABORT)) 531 udma_unset(priv, REGS_DMA_RX, 532 UDMA_RX_BUFx_STATUS(priv->rx_next_buf), 533 UDMA_RX_BUFX_STATUS_DATA_RDY); 534 rx_done_isr &= ~check_isr; 535 priv->rx_next_buf++; 536 if (priv->rx_next_buf == RX_BUFS_COUNT) 537 priv->rx_next_buf = 0; 538 } 539 } 540 541 static void brcmuart_tx_isr(struct uart_port *up, u32 isr) 542 { 543 struct brcmuart_priv *priv = up->private_data; 544 struct device *dev = up->dev; 545 struct uart_8250_port *port_8250 = up_to_u8250p(up); 546 struct circ_buf *xmit = &port_8250->port.state->xmit; 547 548 if (isr & UDMA_INTR_TX_ABORT) { 549 if (priv->tx_running) 550 dev_err(dev, "Unexpected TX_ABORT interrupt\n"); 551 return; 552 } 553 priv->tx_running = false; 554 if (!uart_circ_empty(xmit) && !uart_tx_stopped(up)) 555 brcmuart_tx_dma(port_8250); 556 } 557 558 static irqreturn_t brcmuart_isr(int irq, void *dev_id) 559 { 560 struct uart_port *up = dev_id; 561 struct device *dev = up->dev; 562 struct brcmuart_priv *priv = up->private_data; 563 unsigned long flags; 564 u32 interrupts; 565 u32 rval; 566 u32 tval; 567 568 interrupts = udma_readl(priv, REGS_DMA_ISR, UDMA_INTR_STATUS); 569 if (interrupts == 0) 570 return IRQ_NONE; 571 572 spin_lock_irqsave(&up->lock, flags); 573 574 /* Clear all interrupts */ 575 udma_writel(priv, REGS_DMA_ISR, UDMA_INTR_CLEAR, interrupts); 576 577 rval = UDMA_IS_RX_INTERRUPT(interrupts); 578 if (rval) 579 brcmuart_rx_isr(up, rval); 580 tval = UDMA_IS_TX_INTERRUPT(interrupts); 581 if (tval) 582 brcmuart_tx_isr(up, tval); 583 if ((rval | tval) == 0) 584 dev_warn(dev, "Spurious interrupt: 0x%x\n", interrupts); 585 586 spin_unlock_irqrestore(&up->lock, flags); 587 return IRQ_HANDLED; 588 } 589 590 static int brcmuart_startup(struct uart_port *port) 591 { 592 int res; 593 struct uart_8250_port *up = up_to_u8250p(port); 594 struct brcmuart_priv *priv = up->port.private_data; 595 596 priv->shutdown = false; 597 598 /* 599 * prevent serial8250_do_startup() from allocating non-existent 600 * DMA resources 601 */ 602 up->dma = NULL; 603 604 res = serial8250_do_startup(port); 605 if (!priv->dma_enabled) 606 return res; 607 /* 608 * Disable the Receive Data Interrupt because the DMA engine 609 * will handle this. 610 */ 611 up->ier &= ~UART_IER_RDI; 612 serial_port_out(port, UART_IER, up->ier); 613 614 priv->tx_running = false; 615 priv->dma.rx_dma = NULL; 616 priv->dma.tx_dma = brcmuart_tx_dma; 617 up->dma = &priv->dma; 618 619 brcmuart_init_dma_hardware(priv); 620 start_rx_dma(up); 621 return res; 622 } 623 624 static void brcmuart_shutdown(struct uart_port *port) 625 { 626 struct uart_8250_port *up = up_to_u8250p(port); 627 struct brcmuart_priv *priv = up->port.private_data; 628 unsigned long flags; 629 630 spin_lock_irqsave(&port->lock, flags); 631 priv->shutdown = true; 632 if (priv->dma_enabled) { 633 stop_rx_dma(up); 634 stop_tx_dma(up); 635 /* disable all interrupts */ 636 udma_writel(priv, REGS_DMA_ISR, UDMA_INTR_MASK_SET, 637 UDMA_RX_INTERRUPTS | UDMA_TX_INTERRUPTS); 638 } 639 640 /* 641 * prevent serial8250_do_shutdown() from trying to free 642 * DMA resources that we never alloc'd for this driver. 643 */ 644 up->dma = NULL; 645 646 spin_unlock_irqrestore(&port->lock, flags); 647 serial8250_do_shutdown(port); 648 } 649 650 /* 651 * Not all clocks run at the exact specified rate, so set each requested 652 * rate and then get the actual rate. 653 */ 654 static void init_real_clk_rates(struct device *dev, struct brcmuart_priv *priv) 655 { 656 int x; 657 int rc; 658 659 priv->default_mux_rate = clk_get_rate(priv->baud_mux_clk); 660 for (x = 0; x < ARRAY_SIZE(priv->real_rates); x++) { 661 if (priv->rate_table[x] == 0) { 662 priv->real_rates[x] = 0; 663 continue; 664 } 665 rc = clk_set_rate(priv->baud_mux_clk, priv->rate_table[x]); 666 if (rc) { 667 dev_err(dev, "Error selecting BAUD MUX clock for %u\n", 668 priv->rate_table[x]); 669 priv->real_rates[x] = priv->rate_table[x]; 670 } else { 671 priv->real_rates[x] = clk_get_rate(priv->baud_mux_clk); 672 } 673 } 674 clk_set_rate(priv->baud_mux_clk, priv->default_mux_rate); 675 } 676 677 static void set_clock_mux(struct uart_port *up, struct brcmuart_priv *priv, 678 u32 baud) 679 { 680 u32 percent; 681 u32 best_percent = UINT_MAX; 682 u32 quot; 683 u32 best_quot = 1; 684 u32 rate; 685 int best_index = -1; 686 u64 hires_rate; 687 u64 hires_baud; 688 u64 hires_err; 689 int rc; 690 int i; 691 int real_baud; 692 693 /* If the Baud Mux Clock was not specified, just return */ 694 if (priv->baud_mux_clk == NULL) 695 return; 696 697 /* Find the closest match for specified baud */ 698 for (i = 0; i < ARRAY_SIZE(priv->real_rates); i++) { 699 if (priv->real_rates[i] == 0) 700 continue; 701 rate = priv->real_rates[i] / 16; 702 quot = DIV_ROUND_CLOSEST(rate, baud); 703 if (!quot) 704 continue; 705 706 /* increase resolution to get xx.xx percent */ 707 hires_rate = (u64)rate * 10000; 708 hires_baud = (u64)baud * 10000; 709 710 hires_err = div_u64(hires_rate, (u64)quot); 711 712 /* get the delta */ 713 if (hires_err > hires_baud) 714 hires_err = (hires_err - hires_baud); 715 else 716 hires_err = (hires_baud - hires_err); 717 718 percent = (unsigned long)DIV_ROUND_CLOSEST_ULL(hires_err, baud); 719 dev_dbg(up->dev, 720 "Baud rate: %u, MUX Clk: %u, Error: %u.%u%%\n", 721 baud, priv->real_rates[i], percent / 100, 722 percent % 100); 723 if (percent < best_percent) { 724 best_percent = percent; 725 best_index = i; 726 best_quot = quot; 727 } 728 } 729 if (best_index == -1) { 730 dev_err(up->dev, "Error, %d BAUD rate is too fast.\n", baud); 731 return; 732 } 733 rate = priv->real_rates[best_index]; 734 rc = clk_set_rate(priv->baud_mux_clk, rate); 735 if (rc) 736 dev_err(up->dev, "Error selecting BAUD MUX clock\n"); 737 738 /* Error over 3 percent will cause data errors */ 739 if (best_percent > 300) 740 dev_err(up->dev, "Error, baud: %d has %u.%u%% error\n", 741 baud, percent / 100, percent % 100); 742 743 real_baud = rate / 16 / best_quot; 744 dev_dbg(up->dev, "Selecting BAUD MUX rate: %u\n", rate); 745 dev_dbg(up->dev, "Requested baud: %u, Actual baud: %u\n", 746 baud, real_baud); 747 748 /* calc nanoseconds for 1.5 characters time at the given baud rate */ 749 i = NSEC_PER_SEC / real_baud / 10; 750 i += (i / 2); 751 priv->char_wait = ns_to_ktime(i); 752 753 up->uartclk = rate; 754 } 755 756 static void brcmstb_set_termios(struct uart_port *up, 757 struct ktermios *termios, 758 struct ktermios *old) 759 { 760 struct uart_8250_port *p8250 = up_to_u8250p(up); 761 struct brcmuart_priv *priv = up->private_data; 762 763 if (priv->dma_enabled) 764 stop_rx_dma(p8250); 765 set_clock_mux(up, priv, tty_termios_baud_rate(termios)); 766 serial8250_do_set_termios(up, termios, old); 767 if (p8250->mcr & UART_MCR_AFE) 768 p8250->port.status |= UPSTAT_AUTOCTS; 769 if (priv->dma_enabled) 770 start_rx_dma(p8250); 771 } 772 773 static int brcmuart_handle_irq(struct uart_port *p) 774 { 775 unsigned int iir = serial_port_in(p, UART_IIR); 776 struct brcmuart_priv *priv = p->private_data; 777 struct uart_8250_port *up = up_to_u8250p(p); 778 unsigned int status; 779 unsigned long flags; 780 unsigned int ier; 781 unsigned int mcr; 782 int handled = 0; 783 784 /* 785 * There's a bug in some 8250 cores where we get a timeout 786 * interrupt but there is no data ready. 787 */ 788 if (((iir & UART_IIR_ID) == UART_IIR_RX_TIMEOUT) && !(priv->shutdown)) { 789 spin_lock_irqsave(&p->lock, flags); 790 status = serial_port_in(p, UART_LSR); 791 if ((status & UART_LSR_DR) == 0) { 792 793 ier = serial_port_in(p, UART_IER); 794 /* 795 * if Receive Data Interrupt is enabled and 796 * we're uing hardware flow control, deassert 797 * RTS and wait for any chars in the pipline to 798 * arrive and then check for DR again. 799 */ 800 if ((ier & UART_IER_RDI) && (up->mcr & UART_MCR_AFE)) { 801 ier &= ~(UART_IER_RLSI | UART_IER_RDI); 802 serial_port_out(p, UART_IER, ier); 803 mcr = serial_port_in(p, UART_MCR); 804 mcr &= ~UART_MCR_RTS; 805 serial_port_out(p, UART_MCR, mcr); 806 hrtimer_start(&priv->hrt, priv->char_wait, 807 HRTIMER_MODE_REL); 808 } else { 809 serial_port_in(p, UART_RX); 810 } 811 812 handled = 1; 813 } 814 spin_unlock_irqrestore(&p->lock, flags); 815 if (handled) 816 return 1; 817 } 818 return serial8250_handle_irq(p, iir); 819 } 820 821 static enum hrtimer_restart brcmuart_hrtimer_func(struct hrtimer *t) 822 { 823 struct brcmuart_priv *priv = container_of(t, struct brcmuart_priv, hrt); 824 struct uart_port *p = priv->up; 825 struct uart_8250_port *up = up_to_u8250p(p); 826 unsigned int status; 827 unsigned long flags; 828 829 if (priv->shutdown) 830 return HRTIMER_NORESTART; 831 832 spin_lock_irqsave(&p->lock, flags); 833 status = serial_port_in(p, UART_LSR); 834 835 /* 836 * If a character did not arrive after the timeout, clear the false 837 * receive timeout. 838 */ 839 if ((status & UART_LSR_DR) == 0) { 840 serial_port_in(p, UART_RX); 841 priv->rx_bad_timeout_no_char++; 842 } else { 843 priv->rx_bad_timeout_late_char++; 844 } 845 846 /* re-enable receive unless upper layer has disabled it */ 847 if ((up->ier & (UART_IER_RLSI | UART_IER_RDI)) == 848 (UART_IER_RLSI | UART_IER_RDI)) { 849 status = serial_port_in(p, UART_IER); 850 status |= (UART_IER_RLSI | UART_IER_RDI); 851 serial_port_out(p, UART_IER, status); 852 status = serial_port_in(p, UART_MCR); 853 status |= UART_MCR_RTS; 854 serial_port_out(p, UART_MCR, status); 855 } 856 spin_unlock_irqrestore(&p->lock, flags); 857 return HRTIMER_NORESTART; 858 } 859 860 static const struct of_device_id brcmuart_dt_ids[] = { 861 { 862 .compatible = "brcm,bcm7278-uart", 863 .data = brcmstb_rate_table_7278, 864 }, 865 { 866 .compatible = "brcm,bcm7271-uart", 867 .data = brcmstb_rate_table, 868 }, 869 {}, 870 }; 871 872 MODULE_DEVICE_TABLE(of, brcmuart_dt_ids); 873 874 static void brcmuart_free_bufs(struct device *dev, struct brcmuart_priv *priv) 875 { 876 if (priv->rx_bufs) 877 dma_free_coherent(dev, priv->rx_size, priv->rx_bufs, 878 priv->rx_addr); 879 if (priv->tx_buf) 880 dma_free_coherent(dev, priv->tx_size, priv->tx_buf, 881 priv->tx_addr); 882 } 883 884 static void brcmuart_throttle(struct uart_port *port) 885 { 886 struct brcmuart_priv *priv = port->private_data; 887 888 udma_writel(priv, REGS_DMA_ISR, UDMA_INTR_MASK_SET, UDMA_RX_INTERRUPTS); 889 } 890 891 static void brcmuart_unthrottle(struct uart_port *port) 892 { 893 struct brcmuart_priv *priv = port->private_data; 894 895 udma_writel(priv, REGS_DMA_ISR, UDMA_INTR_MASK_CLEAR, 896 UDMA_RX_INTERRUPTS); 897 } 898 899 static int debugfs_stats_show(struct seq_file *s, void *unused) 900 { 901 struct brcmuart_priv *priv = s->private; 902 903 seq_printf(s, "rx_err:\t\t\t\t%u\n", 904 priv->rx_err); 905 seq_printf(s, "rx_timeout:\t\t\t%u\n", 906 priv->rx_timeout); 907 seq_printf(s, "rx_abort:\t\t\t%u\n", 908 priv->rx_abort); 909 seq_printf(s, "rx_bad_timeout_late_char:\t%u\n", 910 priv->rx_bad_timeout_late_char); 911 seq_printf(s, "rx_bad_timeout_no_char:\t\t%u\n", 912 priv->rx_bad_timeout_no_char); 913 seq_printf(s, "rx_missing_close_timeout:\t%u\n", 914 priv->rx_missing_close_timeout); 915 if (priv->dma_enabled) { 916 seq_printf(s, "dma_rx_partial_buf:\t\t%llu\n", 917 priv->dma_rx_partial_buf); 918 seq_printf(s, "dma_rx_full_buf:\t\t%llu\n", 919 priv->dma_rx_full_buf); 920 } 921 return 0; 922 } 923 DEFINE_SHOW_ATTRIBUTE(debugfs_stats); 924 925 static void brcmuart_init_debugfs(struct brcmuart_priv *priv, 926 const char *device) 927 { 928 priv->debugfs_dir = debugfs_create_dir(device, brcmuart_debugfs_root); 929 debugfs_create_file("stats", 0444, priv->debugfs_dir, priv, 930 &debugfs_stats_fops); 931 } 932 933 934 static int brcmuart_probe(struct platform_device *pdev) 935 { 936 struct resource *regs; 937 struct device_node *np = pdev->dev.of_node; 938 const struct of_device_id *of_id = NULL; 939 struct uart_8250_port *new_port; 940 struct device *dev = &pdev->dev; 941 struct brcmuart_priv *priv; 942 struct clk *baud_mux_clk; 943 struct uart_8250_port up; 944 int irq; 945 void __iomem *membase = NULL; 946 resource_size_t mapbase = 0; 947 u32 clk_rate = 0; 948 int ret; 949 int x; 950 int dma_irq; 951 static const char * const reg_names[REGS_MAX] = { 952 "uart", "dma_rx", "dma_tx", "dma_intr2", "dma_arb" 953 }; 954 955 irq = platform_get_irq(pdev, 0); 956 if (irq < 0) 957 return irq; 958 priv = devm_kzalloc(dev, sizeof(struct brcmuart_priv), 959 GFP_KERNEL); 960 if (!priv) 961 return -ENOMEM; 962 963 of_id = of_match_node(brcmuart_dt_ids, np); 964 if (!of_id || !of_id->data) 965 priv->rate_table = brcmstb_rate_table; 966 else 967 priv->rate_table = of_id->data; 968 969 for (x = 0; x < REGS_MAX; x++) { 970 regs = platform_get_resource_byname(pdev, IORESOURCE_MEM, 971 reg_names[x]); 972 if (!regs) 973 break; 974 priv->regs[x] = devm_ioremap(dev, regs->start, 975 resource_size(regs)); 976 if (!priv->regs[x]) 977 return -ENOMEM; 978 if (x == REGS_8250) { 979 mapbase = regs->start; 980 membase = priv->regs[x]; 981 } 982 } 983 984 /* We should have just the uart base registers or all the registers */ 985 if (x != 1 && x != REGS_MAX) { 986 dev_warn(dev, "%s registers not specified\n", reg_names[x]); 987 return -EINVAL; 988 } 989 990 /* if the DMA registers were specified, try to enable DMA */ 991 if (x > REGS_DMA_RX) { 992 if (brcmuart_arbitration(priv, 1) == 0) { 993 u32 txrev = 0; 994 u32 rxrev = 0; 995 996 txrev = udma_readl(priv, REGS_DMA_RX, UDMA_RX_REVISION); 997 rxrev = udma_readl(priv, REGS_DMA_TX, UDMA_TX_REVISION); 998 if ((txrev >= UDMA_TX_REVISION_REQUIRED) && 999 (rxrev >= UDMA_RX_REVISION_REQUIRED)) { 1000 1001 /* Enable the use of the DMA hardware */ 1002 priv->dma_enabled = true; 1003 } else { 1004 brcmuart_arbitration(priv, 0); 1005 dev_err(dev, 1006 "Unsupported DMA Hardware Revision\n"); 1007 } 1008 } else { 1009 dev_err(dev, 1010 "Timeout arbitrating for UART DMA hardware\n"); 1011 } 1012 } 1013 1014 of_property_read_u32(np, "clock-frequency", &clk_rate); 1015 1016 /* See if a Baud clock has been specified */ 1017 baud_mux_clk = of_clk_get_by_name(np, "sw_baud"); 1018 if (IS_ERR(baud_mux_clk)) { 1019 if (PTR_ERR(baud_mux_clk) == -EPROBE_DEFER) 1020 return -EPROBE_DEFER; 1021 dev_dbg(dev, "BAUD MUX clock not specified\n"); 1022 } else { 1023 dev_dbg(dev, "BAUD MUX clock found\n"); 1024 ret = clk_prepare_enable(baud_mux_clk); 1025 if (ret) 1026 return ret; 1027 priv->baud_mux_clk = baud_mux_clk; 1028 init_real_clk_rates(dev, priv); 1029 clk_rate = priv->default_mux_rate; 1030 } 1031 1032 if (clk_rate == 0) { 1033 dev_err(dev, "clock-frequency or clk not defined\n"); 1034 return -EINVAL; 1035 } 1036 1037 dev_dbg(dev, "DMA is %senabled\n", priv->dma_enabled ? "" : "not "); 1038 1039 memset(&up, 0, sizeof(up)); 1040 up.port.type = PORT_16550A; 1041 up.port.uartclk = clk_rate; 1042 up.port.dev = dev; 1043 up.port.mapbase = mapbase; 1044 up.port.membase = membase; 1045 up.port.irq = irq; 1046 up.port.handle_irq = brcmuart_handle_irq; 1047 up.port.regshift = 2; 1048 up.port.iotype = of_device_is_big_endian(np) ? 1049 UPIO_MEM32BE : UPIO_MEM32; 1050 up.port.flags = UPF_SHARE_IRQ | UPF_BOOT_AUTOCONF 1051 | UPF_FIXED_PORT | UPF_FIXED_TYPE; 1052 up.port.dev = dev; 1053 up.port.private_data = priv; 1054 up.capabilities = UART_CAP_FIFO | UART_CAP_AFE; 1055 up.port.fifosize = 32; 1056 1057 /* Check for a fixed line number */ 1058 ret = of_alias_get_id(np, "serial"); 1059 if (ret >= 0) 1060 up.port.line = ret; 1061 1062 /* setup HR timer */ 1063 hrtimer_init(&priv->hrt, CLOCK_MONOTONIC, HRTIMER_MODE_ABS); 1064 priv->hrt.function = brcmuart_hrtimer_func; 1065 1066 up.port.shutdown = brcmuart_shutdown; 1067 up.port.startup = brcmuart_startup; 1068 up.port.throttle = brcmuart_throttle; 1069 up.port.unthrottle = brcmuart_unthrottle; 1070 up.port.set_termios = brcmstb_set_termios; 1071 1072 if (priv->dma_enabled) { 1073 priv->rx_size = RX_BUF_SIZE * RX_BUFS_COUNT; 1074 priv->rx_bufs = dma_alloc_coherent(dev, 1075 priv->rx_size, 1076 &priv->rx_addr, GFP_KERNEL); 1077 if (!priv->rx_bufs) { 1078 ret = -ENOMEM; 1079 goto err; 1080 } 1081 priv->tx_size = UART_XMIT_SIZE; 1082 priv->tx_buf = dma_alloc_coherent(dev, 1083 priv->tx_size, 1084 &priv->tx_addr, GFP_KERNEL); 1085 if (!priv->tx_buf) { 1086 ret = -ENOMEM; 1087 goto err; 1088 } 1089 } 1090 1091 ret = serial8250_register_8250_port(&up); 1092 if (ret < 0) { 1093 dev_err(dev, "unable to register 8250 port\n"); 1094 goto err; 1095 } 1096 priv->line = ret; 1097 new_port = serial8250_get_port(ret); 1098 priv->up = &new_port->port; 1099 if (priv->dma_enabled) { 1100 dma_irq = platform_get_irq_byname(pdev, "dma"); 1101 if (dma_irq < 0) { 1102 ret = dma_irq; 1103 dev_err(dev, "no IRQ resource info\n"); 1104 goto err1; 1105 } 1106 ret = devm_request_irq(dev, dma_irq, brcmuart_isr, 1107 IRQF_SHARED, "uart DMA irq", &new_port->port); 1108 if (ret) { 1109 dev_err(dev, "unable to register IRQ handler\n"); 1110 goto err1; 1111 } 1112 } 1113 platform_set_drvdata(pdev, priv); 1114 brcmuart_init_debugfs(priv, dev_name(&pdev->dev)); 1115 return 0; 1116 1117 err1: 1118 serial8250_unregister_port(priv->line); 1119 err: 1120 brcmuart_free_bufs(dev, priv); 1121 brcmuart_arbitration(priv, 0); 1122 return ret; 1123 } 1124 1125 static int brcmuart_remove(struct platform_device *pdev) 1126 { 1127 struct brcmuart_priv *priv = platform_get_drvdata(pdev); 1128 1129 debugfs_remove_recursive(priv->debugfs_dir); 1130 hrtimer_cancel(&priv->hrt); 1131 serial8250_unregister_port(priv->line); 1132 brcmuart_free_bufs(&pdev->dev, priv); 1133 brcmuart_arbitration(priv, 0); 1134 return 0; 1135 } 1136 1137 static int __maybe_unused brcmuart_suspend(struct device *dev) 1138 { 1139 struct brcmuart_priv *priv = dev_get_drvdata(dev); 1140 struct uart_8250_port *up = serial8250_get_port(priv->line); 1141 struct uart_port *port = &up->port; 1142 unsigned long flags; 1143 1144 /* 1145 * This will prevent resume from enabling RTS before the 1146 * baud rate has been restored. 1147 */ 1148 spin_lock_irqsave(&port->lock, flags); 1149 priv->saved_mctrl = port->mctrl; 1150 port->mctrl &= ~TIOCM_RTS; 1151 spin_unlock_irqrestore(&port->lock, flags); 1152 1153 serial8250_suspend_port(priv->line); 1154 clk_disable_unprepare(priv->baud_mux_clk); 1155 1156 return 0; 1157 } 1158 1159 static int __maybe_unused brcmuart_resume(struct device *dev) 1160 { 1161 struct brcmuart_priv *priv = dev_get_drvdata(dev); 1162 struct uart_8250_port *up = serial8250_get_port(priv->line); 1163 struct uart_port *port = &up->port; 1164 unsigned long flags; 1165 int ret; 1166 1167 ret = clk_prepare_enable(priv->baud_mux_clk); 1168 if (ret) 1169 dev_err(dev, "Error enabling BAUD MUX clock\n"); 1170 1171 /* 1172 * The hardware goes back to it's default after suspend 1173 * so get the "clk" back in sync. 1174 */ 1175 ret = clk_set_rate(priv->baud_mux_clk, priv->default_mux_rate); 1176 if (ret) 1177 dev_err(dev, "Error restoring default BAUD MUX clock\n"); 1178 if (priv->dma_enabled) { 1179 if (brcmuart_arbitration(priv, 1)) { 1180 dev_err(dev, "Timeout arbitrating for DMA hardware on resume\n"); 1181 return(-EBUSY); 1182 } 1183 brcmuart_init_dma_hardware(priv); 1184 start_rx_dma(serial8250_get_port(priv->line)); 1185 } 1186 serial8250_resume_port(priv->line); 1187 1188 if (priv->saved_mctrl & TIOCM_RTS) { 1189 /* Restore RTS */ 1190 spin_lock_irqsave(&port->lock, flags); 1191 port->mctrl |= TIOCM_RTS; 1192 port->ops->set_mctrl(port, port->mctrl); 1193 spin_unlock_irqrestore(&port->lock, flags); 1194 } 1195 1196 return 0; 1197 } 1198 1199 static const struct dev_pm_ops brcmuart_dev_pm_ops = { 1200 SET_SYSTEM_SLEEP_PM_OPS(brcmuart_suspend, brcmuart_resume) 1201 }; 1202 1203 static struct platform_driver brcmuart_platform_driver = { 1204 .driver = { 1205 .name = "bcm7271-uart", 1206 .pm = &brcmuart_dev_pm_ops, 1207 .of_match_table = brcmuart_dt_ids, 1208 }, 1209 .probe = brcmuart_probe, 1210 .remove = brcmuart_remove, 1211 }; 1212 1213 static int __init brcmuart_init(void) 1214 { 1215 brcmuart_debugfs_root = debugfs_create_dir( 1216 brcmuart_platform_driver.driver.name, NULL); 1217 return platform_driver_register(&brcmuart_platform_driver); 1218 } 1219 module_init(brcmuart_init); 1220 1221 static void __exit brcmuart_deinit(void) 1222 { 1223 platform_driver_unregister(&brcmuart_platform_driver); 1224 debugfs_remove_recursive(brcmuart_debugfs_root); 1225 } 1226 module_exit(brcmuart_deinit); 1227 1228 MODULE_AUTHOR("Al Cooper"); 1229 MODULE_DESCRIPTION("Broadcom NS16550A compatible serial port driver"); 1230 MODULE_LICENSE("GPL v2"); 1231