1 /* 2 * mxser.c -- MOXA Smartio/Industio family multiport serial driver. 3 * 4 * Copyright (C) 1999-2006 Moxa Technologies (support@moxa.com). 5 * Copyright (C) 2006-2008 Jiri Slaby <jirislaby@gmail.com> 6 * 7 * This code is loosely based on the 1.8 moxa driver which is based on 8 * Linux serial driver, written by Linus Torvalds, Theodore T'so and 9 * others. 10 * 11 * This program is free software; you can redistribute it and/or modify 12 * it under the terms of the GNU General Public License as published by 13 * the Free Software Foundation; either version 2 of the License, or 14 * (at your option) any later version. 15 * 16 * Fed through a cleanup, indent and remove of non 2.6 code by Alan Cox 17 * <alan@lxorguk.ukuu.org.uk>. The original 1.8 code is available on 18 * www.moxa.com. 19 * - Fixed x86_64 cleanness 20 */ 21 22 #include <linux/module.h> 23 #include <linux/errno.h> 24 #include <linux/signal.h> 25 #include <linux/sched.h> 26 #include <linux/timer.h> 27 #include <linux/interrupt.h> 28 #include <linux/tty.h> 29 #include <linux/tty_flip.h> 30 #include <linux/serial.h> 31 #include <linux/serial_reg.h> 32 #include <linux/major.h> 33 #include <linux/string.h> 34 #include <linux/fcntl.h> 35 #include <linux/ptrace.h> 36 #include <linux/ioport.h> 37 #include <linux/mm.h> 38 #include <linux/delay.h> 39 #include <linux/pci.h> 40 #include <linux/bitops.h> 41 #include <linux/slab.h> 42 #include <linux/ratelimit.h> 43 44 #include <asm/io.h> 45 #include <asm/irq.h> 46 #include <asm/uaccess.h> 47 48 #include "mxser.h" 49 50 #define MXSER_VERSION "2.0.5" /* 1.14 */ 51 #define MXSERMAJOR 174 52 53 #define MXSER_BOARDS 4 /* Max. boards */ 54 #define MXSER_PORTS_PER_BOARD 8 /* Max. ports per board */ 55 #define MXSER_PORTS (MXSER_BOARDS * MXSER_PORTS_PER_BOARD) 56 #define MXSER_ISR_PASS_LIMIT 100 57 58 /*CheckIsMoxaMust return value*/ 59 #define MOXA_OTHER_UART 0x00 60 #define MOXA_MUST_MU150_HWID 0x01 61 #define MOXA_MUST_MU860_HWID 0x02 62 63 #define WAKEUP_CHARS 256 64 65 #define UART_MCR_AFE 0x20 66 #define UART_LSR_SPECIAL 0x1E 67 68 #define PCI_DEVICE_ID_POS104UL 0x1044 69 #define PCI_DEVICE_ID_CB108 0x1080 70 #define PCI_DEVICE_ID_CP102UF 0x1023 71 #define PCI_DEVICE_ID_CP112UL 0x1120 72 #define PCI_DEVICE_ID_CB114 0x1142 73 #define PCI_DEVICE_ID_CP114UL 0x1143 74 #define PCI_DEVICE_ID_CB134I 0x1341 75 #define PCI_DEVICE_ID_CP138U 0x1380 76 77 78 #define C168_ASIC_ID 1 79 #define C104_ASIC_ID 2 80 #define C102_ASIC_ID 0xB 81 #define CI132_ASIC_ID 4 82 #define CI134_ASIC_ID 3 83 #define CI104J_ASIC_ID 5 84 85 #define MXSER_HIGHBAUD 1 86 #define MXSER_HAS2 2 87 88 /* This is only for PCI */ 89 static const struct { 90 int type; 91 int tx_fifo; 92 int rx_fifo; 93 int xmit_fifo_size; 94 int rx_high_water; 95 int rx_trigger; 96 int rx_low_water; 97 long max_baud; 98 } Gpci_uart_info[] = { 99 {MOXA_OTHER_UART, 16, 16, 16, 14, 14, 1, 921600L}, 100 {MOXA_MUST_MU150_HWID, 64, 64, 64, 48, 48, 16, 230400L}, 101 {MOXA_MUST_MU860_HWID, 128, 128, 128, 96, 96, 32, 921600L} 102 }; 103 #define UART_INFO_NUM ARRAY_SIZE(Gpci_uart_info) 104 105 struct mxser_cardinfo { 106 char *name; 107 unsigned int nports; 108 unsigned int flags; 109 }; 110 111 static const struct mxser_cardinfo mxser_cards[] = { 112 /* 0*/ { "C168 series", 8, }, 113 { "C104 series", 4, }, 114 { "CI-104J series", 4, }, 115 { "C168H/PCI series", 8, }, 116 { "C104H/PCI series", 4, }, 117 /* 5*/ { "C102 series", 4, MXSER_HAS2 }, /* C102-ISA */ 118 { "CI-132 series", 4, MXSER_HAS2 }, 119 { "CI-134 series", 4, }, 120 { "CP-132 series", 2, }, 121 { "CP-114 series", 4, }, 122 /*10*/ { "CT-114 series", 4, }, 123 { "CP-102 series", 2, MXSER_HIGHBAUD }, 124 { "CP-104U series", 4, }, 125 { "CP-168U series", 8, }, 126 { "CP-132U series", 2, }, 127 /*15*/ { "CP-134U series", 4, }, 128 { "CP-104JU series", 4, }, 129 { "Moxa UC7000 Serial", 8, }, /* RC7000 */ 130 { "CP-118U series", 8, }, 131 { "CP-102UL series", 2, }, 132 /*20*/ { "CP-102U series", 2, }, 133 { "CP-118EL series", 8, }, 134 { "CP-168EL series", 8, }, 135 { "CP-104EL series", 4, }, 136 { "CB-108 series", 8, }, 137 /*25*/ { "CB-114 series", 4, }, 138 { "CB-134I series", 4, }, 139 { "CP-138U series", 8, }, 140 { "POS-104UL series", 4, }, 141 { "CP-114UL series", 4, }, 142 /*30*/ { "CP-102UF series", 2, }, 143 { "CP-112UL series", 2, }, 144 }; 145 146 /* driver_data correspond to the lines in the structure above 147 see also ISA probe function before you change something */ 148 static struct pci_device_id mxser_pcibrds[] = { 149 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_C168), .driver_data = 3 }, 150 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_C104), .driver_data = 4 }, 151 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP132), .driver_data = 8 }, 152 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP114), .driver_data = 9 }, 153 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CT114), .driver_data = 10 }, 154 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP102), .driver_data = 11 }, 155 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP104U), .driver_data = 12 }, 156 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP168U), .driver_data = 13 }, 157 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP132U), .driver_data = 14 }, 158 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP134U), .driver_data = 15 }, 159 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP104JU),.driver_data = 16 }, 160 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_RC7000), .driver_data = 17 }, 161 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP118U), .driver_data = 18 }, 162 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP102UL),.driver_data = 19 }, 163 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP102U), .driver_data = 20 }, 164 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP118EL),.driver_data = 21 }, 165 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP168EL),.driver_data = 22 }, 166 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP104EL),.driver_data = 23 }, 167 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_CB108), .driver_data = 24 }, 168 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_CB114), .driver_data = 25 }, 169 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_CB134I), .driver_data = 26 }, 170 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_CP138U), .driver_data = 27 }, 171 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_POS104UL), .driver_data = 28 }, 172 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_CP114UL), .driver_data = 29 }, 173 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_CP102UF), .driver_data = 30 }, 174 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_CP112UL), .driver_data = 31 }, 175 { } 176 }; 177 MODULE_DEVICE_TABLE(pci, mxser_pcibrds); 178 179 static unsigned long ioaddr[MXSER_BOARDS]; 180 static int ttymajor = MXSERMAJOR; 181 182 /* Variables for insmod */ 183 184 MODULE_AUTHOR("Casper Yang"); 185 MODULE_DESCRIPTION("MOXA Smartio/Industio Family Multiport Board Device Driver"); 186 module_param_array(ioaddr, ulong, NULL, 0); 187 MODULE_PARM_DESC(ioaddr, "ISA io addresses to look for a moxa board"); 188 module_param(ttymajor, int, 0); 189 MODULE_LICENSE("GPL"); 190 191 struct mxser_log { 192 int tick; 193 unsigned long rxcnt[MXSER_PORTS]; 194 unsigned long txcnt[MXSER_PORTS]; 195 }; 196 197 struct mxser_mon { 198 unsigned long rxcnt; 199 unsigned long txcnt; 200 unsigned long up_rxcnt; 201 unsigned long up_txcnt; 202 int modem_status; 203 unsigned char hold_reason; 204 }; 205 206 struct mxser_mon_ext { 207 unsigned long rx_cnt[32]; 208 unsigned long tx_cnt[32]; 209 unsigned long up_rxcnt[32]; 210 unsigned long up_txcnt[32]; 211 int modem_status[32]; 212 213 long baudrate[32]; 214 int databits[32]; 215 int stopbits[32]; 216 int parity[32]; 217 int flowctrl[32]; 218 int fifo[32]; 219 int iftype[32]; 220 }; 221 222 struct mxser_board; 223 224 struct mxser_port { 225 struct tty_port port; 226 struct mxser_board *board; 227 228 unsigned long ioaddr; 229 unsigned long opmode_ioaddr; 230 int max_baud; 231 232 int rx_high_water; 233 int rx_trigger; /* Rx fifo trigger level */ 234 int rx_low_water; 235 int baud_base; /* max. speed */ 236 int type; /* UART type */ 237 238 int x_char; /* xon/xoff character */ 239 int IER; /* Interrupt Enable Register */ 240 int MCR; /* Modem control register */ 241 242 unsigned char stop_rx; 243 unsigned char ldisc_stop_rx; 244 245 int custom_divisor; 246 unsigned char err_shadow; 247 248 struct async_icount icount; /* kernel counters for 4 input interrupts */ 249 int timeout; 250 251 int read_status_mask; 252 int ignore_status_mask; 253 int xmit_fifo_size; 254 int xmit_head; 255 int xmit_tail; 256 int xmit_cnt; 257 258 struct ktermios normal_termios; 259 260 struct mxser_mon mon_data; 261 262 spinlock_t slock; 263 }; 264 265 struct mxser_board { 266 unsigned int idx; 267 int irq; 268 const struct mxser_cardinfo *info; 269 unsigned long vector; 270 unsigned long vector_mask; 271 272 int chip_flag; 273 int uart_type; 274 275 struct mxser_port ports[MXSER_PORTS_PER_BOARD]; 276 }; 277 278 struct mxser_mstatus { 279 tcflag_t cflag; 280 int cts; 281 int dsr; 282 int ri; 283 int dcd; 284 }; 285 286 static struct mxser_board mxser_boards[MXSER_BOARDS]; 287 static struct tty_driver *mxvar_sdriver; 288 static struct mxser_log mxvar_log; 289 static int mxser_set_baud_method[MXSER_PORTS + 1]; 290 291 static void mxser_enable_must_enchance_mode(unsigned long baseio) 292 { 293 u8 oldlcr; 294 u8 efr; 295 296 oldlcr = inb(baseio + UART_LCR); 297 outb(MOXA_MUST_ENTER_ENCHANCE, baseio + UART_LCR); 298 299 efr = inb(baseio + MOXA_MUST_EFR_REGISTER); 300 efr |= MOXA_MUST_EFR_EFRB_ENABLE; 301 302 outb(efr, baseio + MOXA_MUST_EFR_REGISTER); 303 outb(oldlcr, baseio + UART_LCR); 304 } 305 306 #ifdef CONFIG_PCI 307 static void mxser_disable_must_enchance_mode(unsigned long baseio) 308 { 309 u8 oldlcr; 310 u8 efr; 311 312 oldlcr = inb(baseio + UART_LCR); 313 outb(MOXA_MUST_ENTER_ENCHANCE, baseio + UART_LCR); 314 315 efr = inb(baseio + MOXA_MUST_EFR_REGISTER); 316 efr &= ~MOXA_MUST_EFR_EFRB_ENABLE; 317 318 outb(efr, baseio + MOXA_MUST_EFR_REGISTER); 319 outb(oldlcr, baseio + UART_LCR); 320 } 321 #endif 322 323 static void mxser_set_must_xon1_value(unsigned long baseio, u8 value) 324 { 325 u8 oldlcr; 326 u8 efr; 327 328 oldlcr = inb(baseio + UART_LCR); 329 outb(MOXA_MUST_ENTER_ENCHANCE, baseio + UART_LCR); 330 331 efr = inb(baseio + MOXA_MUST_EFR_REGISTER); 332 efr &= ~MOXA_MUST_EFR_BANK_MASK; 333 efr |= MOXA_MUST_EFR_BANK0; 334 335 outb(efr, baseio + MOXA_MUST_EFR_REGISTER); 336 outb(value, baseio + MOXA_MUST_XON1_REGISTER); 337 outb(oldlcr, baseio + UART_LCR); 338 } 339 340 static void mxser_set_must_xoff1_value(unsigned long baseio, u8 value) 341 { 342 u8 oldlcr; 343 u8 efr; 344 345 oldlcr = inb(baseio + UART_LCR); 346 outb(MOXA_MUST_ENTER_ENCHANCE, baseio + UART_LCR); 347 348 efr = inb(baseio + MOXA_MUST_EFR_REGISTER); 349 efr &= ~MOXA_MUST_EFR_BANK_MASK; 350 efr |= MOXA_MUST_EFR_BANK0; 351 352 outb(efr, baseio + MOXA_MUST_EFR_REGISTER); 353 outb(value, baseio + MOXA_MUST_XOFF1_REGISTER); 354 outb(oldlcr, baseio + UART_LCR); 355 } 356 357 static void mxser_set_must_fifo_value(struct mxser_port *info) 358 { 359 u8 oldlcr; 360 u8 efr; 361 362 oldlcr = inb(info->ioaddr + UART_LCR); 363 outb(MOXA_MUST_ENTER_ENCHANCE, info->ioaddr + UART_LCR); 364 365 efr = inb(info->ioaddr + MOXA_MUST_EFR_REGISTER); 366 efr &= ~MOXA_MUST_EFR_BANK_MASK; 367 efr |= MOXA_MUST_EFR_BANK1; 368 369 outb(efr, info->ioaddr + MOXA_MUST_EFR_REGISTER); 370 outb((u8)info->rx_high_water, info->ioaddr + MOXA_MUST_RBRTH_REGISTER); 371 outb((u8)info->rx_trigger, info->ioaddr + MOXA_MUST_RBRTI_REGISTER); 372 outb((u8)info->rx_low_water, info->ioaddr + MOXA_MUST_RBRTL_REGISTER); 373 outb(oldlcr, info->ioaddr + UART_LCR); 374 } 375 376 static void mxser_set_must_enum_value(unsigned long baseio, u8 value) 377 { 378 u8 oldlcr; 379 u8 efr; 380 381 oldlcr = inb(baseio + UART_LCR); 382 outb(MOXA_MUST_ENTER_ENCHANCE, baseio + UART_LCR); 383 384 efr = inb(baseio + MOXA_MUST_EFR_REGISTER); 385 efr &= ~MOXA_MUST_EFR_BANK_MASK; 386 efr |= MOXA_MUST_EFR_BANK2; 387 388 outb(efr, baseio + MOXA_MUST_EFR_REGISTER); 389 outb(value, baseio + MOXA_MUST_ENUM_REGISTER); 390 outb(oldlcr, baseio + UART_LCR); 391 } 392 393 #ifdef CONFIG_PCI 394 static void mxser_get_must_hardware_id(unsigned long baseio, u8 *pId) 395 { 396 u8 oldlcr; 397 u8 efr; 398 399 oldlcr = inb(baseio + UART_LCR); 400 outb(MOXA_MUST_ENTER_ENCHANCE, baseio + UART_LCR); 401 402 efr = inb(baseio + MOXA_MUST_EFR_REGISTER); 403 efr &= ~MOXA_MUST_EFR_BANK_MASK; 404 efr |= MOXA_MUST_EFR_BANK2; 405 406 outb(efr, baseio + MOXA_MUST_EFR_REGISTER); 407 *pId = inb(baseio + MOXA_MUST_HWID_REGISTER); 408 outb(oldlcr, baseio + UART_LCR); 409 } 410 #endif 411 412 static void SET_MOXA_MUST_NO_SOFTWARE_FLOW_CONTROL(unsigned long baseio) 413 { 414 u8 oldlcr; 415 u8 efr; 416 417 oldlcr = inb(baseio + UART_LCR); 418 outb(MOXA_MUST_ENTER_ENCHANCE, baseio + UART_LCR); 419 420 efr = inb(baseio + MOXA_MUST_EFR_REGISTER); 421 efr &= ~MOXA_MUST_EFR_SF_MASK; 422 423 outb(efr, baseio + MOXA_MUST_EFR_REGISTER); 424 outb(oldlcr, baseio + UART_LCR); 425 } 426 427 static void mxser_enable_must_tx_software_flow_control(unsigned long baseio) 428 { 429 u8 oldlcr; 430 u8 efr; 431 432 oldlcr = inb(baseio + UART_LCR); 433 outb(MOXA_MUST_ENTER_ENCHANCE, baseio + UART_LCR); 434 435 efr = inb(baseio + MOXA_MUST_EFR_REGISTER); 436 efr &= ~MOXA_MUST_EFR_SF_TX_MASK; 437 efr |= MOXA_MUST_EFR_SF_TX1; 438 439 outb(efr, baseio + MOXA_MUST_EFR_REGISTER); 440 outb(oldlcr, baseio + UART_LCR); 441 } 442 443 static void mxser_disable_must_tx_software_flow_control(unsigned long baseio) 444 { 445 u8 oldlcr; 446 u8 efr; 447 448 oldlcr = inb(baseio + UART_LCR); 449 outb(MOXA_MUST_ENTER_ENCHANCE, baseio + UART_LCR); 450 451 efr = inb(baseio + MOXA_MUST_EFR_REGISTER); 452 efr &= ~MOXA_MUST_EFR_SF_TX_MASK; 453 454 outb(efr, baseio + MOXA_MUST_EFR_REGISTER); 455 outb(oldlcr, baseio + UART_LCR); 456 } 457 458 static void mxser_enable_must_rx_software_flow_control(unsigned long baseio) 459 { 460 u8 oldlcr; 461 u8 efr; 462 463 oldlcr = inb(baseio + UART_LCR); 464 outb(MOXA_MUST_ENTER_ENCHANCE, baseio + UART_LCR); 465 466 efr = inb(baseio + MOXA_MUST_EFR_REGISTER); 467 efr &= ~MOXA_MUST_EFR_SF_RX_MASK; 468 efr |= MOXA_MUST_EFR_SF_RX1; 469 470 outb(efr, baseio + MOXA_MUST_EFR_REGISTER); 471 outb(oldlcr, baseio + UART_LCR); 472 } 473 474 static void mxser_disable_must_rx_software_flow_control(unsigned long baseio) 475 { 476 u8 oldlcr; 477 u8 efr; 478 479 oldlcr = inb(baseio + UART_LCR); 480 outb(MOXA_MUST_ENTER_ENCHANCE, baseio + UART_LCR); 481 482 efr = inb(baseio + MOXA_MUST_EFR_REGISTER); 483 efr &= ~MOXA_MUST_EFR_SF_RX_MASK; 484 485 outb(efr, baseio + MOXA_MUST_EFR_REGISTER); 486 outb(oldlcr, baseio + UART_LCR); 487 } 488 489 #ifdef CONFIG_PCI 490 static int CheckIsMoxaMust(unsigned long io) 491 { 492 u8 oldmcr, hwid; 493 int i; 494 495 outb(0, io + UART_LCR); 496 mxser_disable_must_enchance_mode(io); 497 oldmcr = inb(io + UART_MCR); 498 outb(0, io + UART_MCR); 499 mxser_set_must_xon1_value(io, 0x11); 500 if ((hwid = inb(io + UART_MCR)) != 0) { 501 outb(oldmcr, io + UART_MCR); 502 return MOXA_OTHER_UART; 503 } 504 505 mxser_get_must_hardware_id(io, &hwid); 506 for (i = 1; i < UART_INFO_NUM; i++) { /* 0 = OTHER_UART */ 507 if (hwid == Gpci_uart_info[i].type) 508 return (int)hwid; 509 } 510 return MOXA_OTHER_UART; 511 } 512 #endif 513 514 static void process_txrx_fifo(struct mxser_port *info) 515 { 516 int i; 517 518 if ((info->type == PORT_16450) || (info->type == PORT_8250)) { 519 info->rx_trigger = 1; 520 info->rx_high_water = 1; 521 info->rx_low_water = 1; 522 info->xmit_fifo_size = 1; 523 } else 524 for (i = 0; i < UART_INFO_NUM; i++) 525 if (info->board->chip_flag == Gpci_uart_info[i].type) { 526 info->rx_trigger = Gpci_uart_info[i].rx_trigger; 527 info->rx_low_water = Gpci_uart_info[i].rx_low_water; 528 info->rx_high_water = Gpci_uart_info[i].rx_high_water; 529 info->xmit_fifo_size = Gpci_uart_info[i].xmit_fifo_size; 530 break; 531 } 532 } 533 534 static unsigned char mxser_get_msr(int baseaddr, int mode, int port) 535 { 536 static unsigned char mxser_msr[MXSER_PORTS + 1]; 537 unsigned char status = 0; 538 539 status = inb(baseaddr + UART_MSR); 540 541 mxser_msr[port] &= 0x0F; 542 mxser_msr[port] |= status; 543 status = mxser_msr[port]; 544 if (mode) 545 mxser_msr[port] = 0; 546 547 return status; 548 } 549 550 static int mxser_carrier_raised(struct tty_port *port) 551 { 552 struct mxser_port *mp = container_of(port, struct mxser_port, port); 553 return (inb(mp->ioaddr + UART_MSR) & UART_MSR_DCD)?1:0; 554 } 555 556 static void mxser_dtr_rts(struct tty_port *port, int on) 557 { 558 struct mxser_port *mp = container_of(port, struct mxser_port, port); 559 unsigned long flags; 560 561 spin_lock_irqsave(&mp->slock, flags); 562 if (on) 563 outb(inb(mp->ioaddr + UART_MCR) | 564 UART_MCR_DTR | UART_MCR_RTS, mp->ioaddr + UART_MCR); 565 else 566 outb(inb(mp->ioaddr + UART_MCR)&~(UART_MCR_DTR | UART_MCR_RTS), 567 mp->ioaddr + UART_MCR); 568 spin_unlock_irqrestore(&mp->slock, flags); 569 } 570 571 static int mxser_set_baud(struct tty_struct *tty, long newspd) 572 { 573 struct mxser_port *info = tty->driver_data; 574 int quot = 0, baud; 575 unsigned char cval; 576 577 if (!info->ioaddr) 578 return -1; 579 580 if (newspd > info->max_baud) 581 return -1; 582 583 if (newspd == 134) { 584 quot = 2 * info->baud_base / 269; 585 tty_encode_baud_rate(tty, 134, 134); 586 } else if (newspd) { 587 quot = info->baud_base / newspd; 588 if (quot == 0) 589 quot = 1; 590 baud = info->baud_base/quot; 591 tty_encode_baud_rate(tty, baud, baud); 592 } else { 593 quot = 0; 594 } 595 596 info->timeout = ((info->xmit_fifo_size * HZ * 10 * quot) / info->baud_base); 597 info->timeout += HZ / 50; /* Add .02 seconds of slop */ 598 599 if (quot) { 600 info->MCR |= UART_MCR_DTR; 601 outb(info->MCR, info->ioaddr + UART_MCR); 602 } else { 603 info->MCR &= ~UART_MCR_DTR; 604 outb(info->MCR, info->ioaddr + UART_MCR); 605 return 0; 606 } 607 608 cval = inb(info->ioaddr + UART_LCR); 609 610 outb(cval | UART_LCR_DLAB, info->ioaddr + UART_LCR); /* set DLAB */ 611 612 outb(quot & 0xff, info->ioaddr + UART_DLL); /* LS of divisor */ 613 outb(quot >> 8, info->ioaddr + UART_DLM); /* MS of divisor */ 614 outb(cval, info->ioaddr + UART_LCR); /* reset DLAB */ 615 616 #ifdef BOTHER 617 if (C_BAUD(tty) == BOTHER) { 618 quot = info->baud_base % newspd; 619 quot *= 8; 620 if (quot % newspd > newspd / 2) { 621 quot /= newspd; 622 quot++; 623 } else 624 quot /= newspd; 625 626 mxser_set_must_enum_value(info->ioaddr, quot); 627 } else 628 #endif 629 mxser_set_must_enum_value(info->ioaddr, 0); 630 631 return 0; 632 } 633 634 /* 635 * This routine is called to set the UART divisor registers to match 636 * the specified baud rate for a serial port. 637 */ 638 static int mxser_change_speed(struct tty_struct *tty, 639 struct ktermios *old_termios) 640 { 641 struct mxser_port *info = tty->driver_data; 642 unsigned cflag, cval, fcr; 643 int ret = 0; 644 unsigned char status; 645 646 cflag = tty->termios.c_cflag; 647 if (!info->ioaddr) 648 return ret; 649 650 if (mxser_set_baud_method[tty->index] == 0) 651 mxser_set_baud(tty, tty_get_baud_rate(tty)); 652 653 /* byte size and parity */ 654 switch (cflag & CSIZE) { 655 case CS5: 656 cval = 0x00; 657 break; 658 case CS6: 659 cval = 0x01; 660 break; 661 case CS7: 662 cval = 0x02; 663 break; 664 case CS8: 665 cval = 0x03; 666 break; 667 default: 668 cval = 0x00; 669 break; /* too keep GCC shut... */ 670 } 671 if (cflag & CSTOPB) 672 cval |= 0x04; 673 if (cflag & PARENB) 674 cval |= UART_LCR_PARITY; 675 if (!(cflag & PARODD)) 676 cval |= UART_LCR_EPAR; 677 if (cflag & CMSPAR) 678 cval |= UART_LCR_SPAR; 679 680 if ((info->type == PORT_8250) || (info->type == PORT_16450)) { 681 if (info->board->chip_flag) { 682 fcr = UART_FCR_ENABLE_FIFO; 683 fcr |= MOXA_MUST_FCR_GDA_MODE_ENABLE; 684 mxser_set_must_fifo_value(info); 685 } else 686 fcr = 0; 687 } else { 688 fcr = UART_FCR_ENABLE_FIFO; 689 if (info->board->chip_flag) { 690 fcr |= MOXA_MUST_FCR_GDA_MODE_ENABLE; 691 mxser_set_must_fifo_value(info); 692 } else { 693 switch (info->rx_trigger) { 694 case 1: 695 fcr |= UART_FCR_TRIGGER_1; 696 break; 697 case 4: 698 fcr |= UART_FCR_TRIGGER_4; 699 break; 700 case 8: 701 fcr |= UART_FCR_TRIGGER_8; 702 break; 703 default: 704 fcr |= UART_FCR_TRIGGER_14; 705 break; 706 } 707 } 708 } 709 710 /* CTS flow control flag and modem status interrupts */ 711 info->IER &= ~UART_IER_MSI; 712 info->MCR &= ~UART_MCR_AFE; 713 if (cflag & CRTSCTS) { 714 info->port.flags |= ASYNC_CTS_FLOW; 715 info->IER |= UART_IER_MSI; 716 if ((info->type == PORT_16550A) || (info->board->chip_flag)) { 717 info->MCR |= UART_MCR_AFE; 718 } else { 719 status = inb(info->ioaddr + UART_MSR); 720 if (tty->hw_stopped) { 721 if (status & UART_MSR_CTS) { 722 tty->hw_stopped = 0; 723 if (info->type != PORT_16550A && 724 !info->board->chip_flag) { 725 outb(info->IER & ~UART_IER_THRI, 726 info->ioaddr + 727 UART_IER); 728 info->IER |= UART_IER_THRI; 729 outb(info->IER, info->ioaddr + 730 UART_IER); 731 } 732 tty_wakeup(tty); 733 } 734 } else { 735 if (!(status & UART_MSR_CTS)) { 736 tty->hw_stopped = 1; 737 if ((info->type != PORT_16550A) && 738 (!info->board->chip_flag)) { 739 info->IER &= ~UART_IER_THRI; 740 outb(info->IER, info->ioaddr + 741 UART_IER); 742 } 743 } 744 } 745 } 746 } else { 747 info->port.flags &= ~ASYNC_CTS_FLOW; 748 } 749 outb(info->MCR, info->ioaddr + UART_MCR); 750 if (cflag & CLOCAL) { 751 info->port.flags &= ~ASYNC_CHECK_CD; 752 } else { 753 info->port.flags |= ASYNC_CHECK_CD; 754 info->IER |= UART_IER_MSI; 755 } 756 outb(info->IER, info->ioaddr + UART_IER); 757 758 /* 759 * Set up parity check flag 760 */ 761 info->read_status_mask = UART_LSR_OE | UART_LSR_THRE | UART_LSR_DR; 762 if (I_INPCK(tty)) 763 info->read_status_mask |= UART_LSR_FE | UART_LSR_PE; 764 if (I_BRKINT(tty) || I_PARMRK(tty)) 765 info->read_status_mask |= UART_LSR_BI; 766 767 info->ignore_status_mask = 0; 768 769 if (I_IGNBRK(tty)) { 770 info->ignore_status_mask |= UART_LSR_BI; 771 info->read_status_mask |= UART_LSR_BI; 772 /* 773 * If we're ignore parity and break indicators, ignore 774 * overruns too. (For real raw support). 775 */ 776 if (I_IGNPAR(tty)) { 777 info->ignore_status_mask |= 778 UART_LSR_OE | 779 UART_LSR_PE | 780 UART_LSR_FE; 781 info->read_status_mask |= 782 UART_LSR_OE | 783 UART_LSR_PE | 784 UART_LSR_FE; 785 } 786 } 787 if (info->board->chip_flag) { 788 mxser_set_must_xon1_value(info->ioaddr, START_CHAR(tty)); 789 mxser_set_must_xoff1_value(info->ioaddr, STOP_CHAR(tty)); 790 if (I_IXON(tty)) { 791 mxser_enable_must_rx_software_flow_control( 792 info->ioaddr); 793 } else { 794 mxser_disable_must_rx_software_flow_control( 795 info->ioaddr); 796 } 797 if (I_IXOFF(tty)) { 798 mxser_enable_must_tx_software_flow_control( 799 info->ioaddr); 800 } else { 801 mxser_disable_must_tx_software_flow_control( 802 info->ioaddr); 803 } 804 } 805 806 807 outb(fcr, info->ioaddr + UART_FCR); /* set fcr */ 808 outb(cval, info->ioaddr + UART_LCR); 809 810 return ret; 811 } 812 813 static void mxser_check_modem_status(struct tty_struct *tty, 814 struct mxser_port *port, int status) 815 { 816 /* update input line counters */ 817 if (status & UART_MSR_TERI) 818 port->icount.rng++; 819 if (status & UART_MSR_DDSR) 820 port->icount.dsr++; 821 if (status & UART_MSR_DDCD) 822 port->icount.dcd++; 823 if (status & UART_MSR_DCTS) 824 port->icount.cts++; 825 port->mon_data.modem_status = status; 826 wake_up_interruptible(&port->port.delta_msr_wait); 827 828 if ((port->port.flags & ASYNC_CHECK_CD) && (status & UART_MSR_DDCD)) { 829 if (status & UART_MSR_DCD) 830 wake_up_interruptible(&port->port.open_wait); 831 } 832 833 if (tty_port_cts_enabled(&port->port)) { 834 if (tty->hw_stopped) { 835 if (status & UART_MSR_CTS) { 836 tty->hw_stopped = 0; 837 838 if ((port->type != PORT_16550A) && 839 (!port->board->chip_flag)) { 840 outb(port->IER & ~UART_IER_THRI, 841 port->ioaddr + UART_IER); 842 port->IER |= UART_IER_THRI; 843 outb(port->IER, port->ioaddr + 844 UART_IER); 845 } 846 tty_wakeup(tty); 847 } 848 } else { 849 if (!(status & UART_MSR_CTS)) { 850 tty->hw_stopped = 1; 851 if (port->type != PORT_16550A && 852 !port->board->chip_flag) { 853 port->IER &= ~UART_IER_THRI; 854 outb(port->IER, port->ioaddr + 855 UART_IER); 856 } 857 } 858 } 859 } 860 } 861 862 static int mxser_activate(struct tty_port *port, struct tty_struct *tty) 863 { 864 struct mxser_port *info = container_of(port, struct mxser_port, port); 865 unsigned long page; 866 unsigned long flags; 867 868 page = __get_free_page(GFP_KERNEL); 869 if (!page) 870 return -ENOMEM; 871 872 spin_lock_irqsave(&info->slock, flags); 873 874 if (!info->ioaddr || !info->type) { 875 set_bit(TTY_IO_ERROR, &tty->flags); 876 free_page(page); 877 spin_unlock_irqrestore(&info->slock, flags); 878 return 0; 879 } 880 info->port.xmit_buf = (unsigned char *) page; 881 882 /* 883 * Clear the FIFO buffers and disable them 884 * (they will be reenabled in mxser_change_speed()) 885 */ 886 if (info->board->chip_flag) 887 outb((UART_FCR_CLEAR_RCVR | 888 UART_FCR_CLEAR_XMIT | 889 MOXA_MUST_FCR_GDA_MODE_ENABLE), info->ioaddr + UART_FCR); 890 else 891 outb((UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT), 892 info->ioaddr + UART_FCR); 893 894 /* 895 * At this point there's no way the LSR could still be 0xFF; 896 * if it is, then bail out, because there's likely no UART 897 * here. 898 */ 899 if (inb(info->ioaddr + UART_LSR) == 0xff) { 900 spin_unlock_irqrestore(&info->slock, flags); 901 if (capable(CAP_SYS_ADMIN)) { 902 set_bit(TTY_IO_ERROR, &tty->flags); 903 return 0; 904 } else 905 return -ENODEV; 906 } 907 908 /* 909 * Clear the interrupt registers. 910 */ 911 (void) inb(info->ioaddr + UART_LSR); 912 (void) inb(info->ioaddr + UART_RX); 913 (void) inb(info->ioaddr + UART_IIR); 914 (void) inb(info->ioaddr + UART_MSR); 915 916 /* 917 * Now, initialize the UART 918 */ 919 outb(UART_LCR_WLEN8, info->ioaddr + UART_LCR); /* reset DLAB */ 920 info->MCR = UART_MCR_DTR | UART_MCR_RTS; 921 outb(info->MCR, info->ioaddr + UART_MCR); 922 923 /* 924 * Finally, enable interrupts 925 */ 926 info->IER = UART_IER_MSI | UART_IER_RLSI | UART_IER_RDI; 927 928 if (info->board->chip_flag) 929 info->IER |= MOXA_MUST_IER_EGDAI; 930 outb(info->IER, info->ioaddr + UART_IER); /* enable interrupts */ 931 932 /* 933 * And clear the interrupt registers again for luck. 934 */ 935 (void) inb(info->ioaddr + UART_LSR); 936 (void) inb(info->ioaddr + UART_RX); 937 (void) inb(info->ioaddr + UART_IIR); 938 (void) inb(info->ioaddr + UART_MSR); 939 940 clear_bit(TTY_IO_ERROR, &tty->flags); 941 info->xmit_cnt = info->xmit_head = info->xmit_tail = 0; 942 943 /* 944 * and set the speed of the serial port 945 */ 946 mxser_change_speed(tty, NULL); 947 spin_unlock_irqrestore(&info->slock, flags); 948 949 return 0; 950 } 951 952 /* 953 * This routine will shutdown a serial port 954 */ 955 static void mxser_shutdown_port(struct tty_port *port) 956 { 957 struct mxser_port *info = container_of(port, struct mxser_port, port); 958 unsigned long flags; 959 960 spin_lock_irqsave(&info->slock, flags); 961 962 /* 963 * clear delta_msr_wait queue to avoid mem leaks: we may free the irq 964 * here so the queue might never be waken up 965 */ 966 wake_up_interruptible(&info->port.delta_msr_wait); 967 968 /* 969 * Free the xmit buffer, if necessary 970 */ 971 if (info->port.xmit_buf) { 972 free_page((unsigned long) info->port.xmit_buf); 973 info->port.xmit_buf = NULL; 974 } 975 976 info->IER = 0; 977 outb(0x00, info->ioaddr + UART_IER); 978 979 /* clear Rx/Tx FIFO's */ 980 if (info->board->chip_flag) 981 outb(UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT | 982 MOXA_MUST_FCR_GDA_MODE_ENABLE, 983 info->ioaddr + UART_FCR); 984 else 985 outb(UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT, 986 info->ioaddr + UART_FCR); 987 988 /* read data port to reset things */ 989 (void) inb(info->ioaddr + UART_RX); 990 991 992 if (info->board->chip_flag) 993 SET_MOXA_MUST_NO_SOFTWARE_FLOW_CONTROL(info->ioaddr); 994 995 spin_unlock_irqrestore(&info->slock, flags); 996 } 997 998 /* 999 * This routine is called whenever a serial port is opened. It 1000 * enables interrupts for a serial port, linking in its async structure into 1001 * the IRQ chain. It also performs the serial-specific 1002 * initialization for the tty structure. 1003 */ 1004 static int mxser_open(struct tty_struct *tty, struct file *filp) 1005 { 1006 struct mxser_port *info; 1007 int line; 1008 1009 line = tty->index; 1010 if (line == MXSER_PORTS) 1011 return 0; 1012 info = &mxser_boards[line / MXSER_PORTS_PER_BOARD].ports[line % MXSER_PORTS_PER_BOARD]; 1013 if (!info->ioaddr) 1014 return -ENODEV; 1015 1016 tty->driver_data = info; 1017 return tty_port_open(&info->port, tty, filp); 1018 } 1019 1020 static void mxser_flush_buffer(struct tty_struct *tty) 1021 { 1022 struct mxser_port *info = tty->driver_data; 1023 char fcr; 1024 unsigned long flags; 1025 1026 1027 spin_lock_irqsave(&info->slock, flags); 1028 info->xmit_cnt = info->xmit_head = info->xmit_tail = 0; 1029 1030 fcr = inb(info->ioaddr + UART_FCR); 1031 outb((fcr | UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT), 1032 info->ioaddr + UART_FCR); 1033 outb(fcr, info->ioaddr + UART_FCR); 1034 1035 spin_unlock_irqrestore(&info->slock, flags); 1036 1037 tty_wakeup(tty); 1038 } 1039 1040 1041 static void mxser_close_port(struct tty_port *port) 1042 { 1043 struct mxser_port *info = container_of(port, struct mxser_port, port); 1044 unsigned long timeout; 1045 /* 1046 * At this point we stop accepting input. To do this, we 1047 * disable the receive line status interrupts, and tell the 1048 * interrupt driver to stop checking the data ready bit in the 1049 * line status register. 1050 */ 1051 info->IER &= ~UART_IER_RLSI; 1052 if (info->board->chip_flag) 1053 info->IER &= ~MOXA_MUST_RECV_ISR; 1054 1055 outb(info->IER, info->ioaddr + UART_IER); 1056 /* 1057 * Before we drop DTR, make sure the UART transmitter 1058 * has completely drained; this is especially 1059 * important if there is a transmit FIFO! 1060 */ 1061 timeout = jiffies + HZ; 1062 while (!(inb(info->ioaddr + UART_LSR) & UART_LSR_TEMT)) { 1063 schedule_timeout_interruptible(5); 1064 if (time_after(jiffies, timeout)) 1065 break; 1066 } 1067 } 1068 1069 /* 1070 * This routine is called when the serial port gets closed. First, we 1071 * wait for the last remaining data to be sent. Then, we unlink its 1072 * async structure from the interrupt chain if necessary, and we free 1073 * that IRQ if nothing is left in the chain. 1074 */ 1075 static void mxser_close(struct tty_struct *tty, struct file *filp) 1076 { 1077 struct mxser_port *info = tty->driver_data; 1078 struct tty_port *port = &info->port; 1079 1080 if (tty->index == MXSER_PORTS || info == NULL) 1081 return; 1082 if (tty_port_close_start(port, tty, filp) == 0) 1083 return; 1084 mutex_lock(&port->mutex); 1085 mxser_close_port(port); 1086 mxser_flush_buffer(tty); 1087 if (test_bit(ASYNCB_INITIALIZED, &port->flags)) { 1088 if (C_HUPCL(tty)) 1089 tty_port_lower_dtr_rts(port); 1090 } 1091 mxser_shutdown_port(port); 1092 clear_bit(ASYNCB_INITIALIZED, &port->flags); 1093 mutex_unlock(&port->mutex); 1094 /* Right now the tty_port set is done outside of the close_end helper 1095 as we don't yet have everyone using refcounts */ 1096 tty_port_close_end(port, tty); 1097 tty_port_tty_set(port, NULL); 1098 } 1099 1100 static int mxser_write(struct tty_struct *tty, const unsigned char *buf, int count) 1101 { 1102 int c, total = 0; 1103 struct mxser_port *info = tty->driver_data; 1104 unsigned long flags; 1105 1106 if (!info->port.xmit_buf) 1107 return 0; 1108 1109 while (1) { 1110 c = min_t(int, count, min(SERIAL_XMIT_SIZE - info->xmit_cnt - 1, 1111 SERIAL_XMIT_SIZE - info->xmit_head)); 1112 if (c <= 0) 1113 break; 1114 1115 memcpy(info->port.xmit_buf + info->xmit_head, buf, c); 1116 spin_lock_irqsave(&info->slock, flags); 1117 info->xmit_head = (info->xmit_head + c) & 1118 (SERIAL_XMIT_SIZE - 1); 1119 info->xmit_cnt += c; 1120 spin_unlock_irqrestore(&info->slock, flags); 1121 1122 buf += c; 1123 count -= c; 1124 total += c; 1125 } 1126 1127 if (info->xmit_cnt && !tty->stopped) { 1128 if (!tty->hw_stopped || 1129 (info->type == PORT_16550A) || 1130 (info->board->chip_flag)) { 1131 spin_lock_irqsave(&info->slock, flags); 1132 outb(info->IER & ~UART_IER_THRI, info->ioaddr + 1133 UART_IER); 1134 info->IER |= UART_IER_THRI; 1135 outb(info->IER, info->ioaddr + UART_IER); 1136 spin_unlock_irqrestore(&info->slock, flags); 1137 } 1138 } 1139 return total; 1140 } 1141 1142 static int mxser_put_char(struct tty_struct *tty, unsigned char ch) 1143 { 1144 struct mxser_port *info = tty->driver_data; 1145 unsigned long flags; 1146 1147 if (!info->port.xmit_buf) 1148 return 0; 1149 1150 if (info->xmit_cnt >= SERIAL_XMIT_SIZE - 1) 1151 return 0; 1152 1153 spin_lock_irqsave(&info->slock, flags); 1154 info->port.xmit_buf[info->xmit_head++] = ch; 1155 info->xmit_head &= SERIAL_XMIT_SIZE - 1; 1156 info->xmit_cnt++; 1157 spin_unlock_irqrestore(&info->slock, flags); 1158 if (!tty->stopped) { 1159 if (!tty->hw_stopped || 1160 (info->type == PORT_16550A) || 1161 info->board->chip_flag) { 1162 spin_lock_irqsave(&info->slock, flags); 1163 outb(info->IER & ~UART_IER_THRI, info->ioaddr + UART_IER); 1164 info->IER |= UART_IER_THRI; 1165 outb(info->IER, info->ioaddr + UART_IER); 1166 spin_unlock_irqrestore(&info->slock, flags); 1167 } 1168 } 1169 return 1; 1170 } 1171 1172 1173 static void mxser_flush_chars(struct tty_struct *tty) 1174 { 1175 struct mxser_port *info = tty->driver_data; 1176 unsigned long flags; 1177 1178 if (info->xmit_cnt <= 0 || tty->stopped || !info->port.xmit_buf || 1179 (tty->hw_stopped && info->type != PORT_16550A && 1180 !info->board->chip_flag)) 1181 return; 1182 1183 spin_lock_irqsave(&info->slock, flags); 1184 1185 outb(info->IER & ~UART_IER_THRI, info->ioaddr + UART_IER); 1186 info->IER |= UART_IER_THRI; 1187 outb(info->IER, info->ioaddr + UART_IER); 1188 1189 spin_unlock_irqrestore(&info->slock, flags); 1190 } 1191 1192 static int mxser_write_room(struct tty_struct *tty) 1193 { 1194 struct mxser_port *info = tty->driver_data; 1195 int ret; 1196 1197 ret = SERIAL_XMIT_SIZE - info->xmit_cnt - 1; 1198 return ret < 0 ? 0 : ret; 1199 } 1200 1201 static int mxser_chars_in_buffer(struct tty_struct *tty) 1202 { 1203 struct mxser_port *info = tty->driver_data; 1204 return info->xmit_cnt; 1205 } 1206 1207 /* 1208 * ------------------------------------------------------------ 1209 * friends of mxser_ioctl() 1210 * ------------------------------------------------------------ 1211 */ 1212 static int mxser_get_serial_info(struct tty_struct *tty, 1213 struct serial_struct __user *retinfo) 1214 { 1215 struct mxser_port *info = tty->driver_data; 1216 struct serial_struct tmp = { 1217 .type = info->type, 1218 .line = tty->index, 1219 .port = info->ioaddr, 1220 .irq = info->board->irq, 1221 .flags = info->port.flags, 1222 .baud_base = info->baud_base, 1223 .close_delay = info->port.close_delay, 1224 .closing_wait = info->port.closing_wait, 1225 .custom_divisor = info->custom_divisor, 1226 .hub6 = 0 1227 }; 1228 if (copy_to_user(retinfo, &tmp, sizeof(*retinfo))) 1229 return -EFAULT; 1230 return 0; 1231 } 1232 1233 static int mxser_set_serial_info(struct tty_struct *tty, 1234 struct serial_struct __user *new_info) 1235 { 1236 struct mxser_port *info = tty->driver_data; 1237 struct tty_port *port = &info->port; 1238 struct serial_struct new_serial; 1239 speed_t baud; 1240 unsigned long sl_flags; 1241 unsigned int flags; 1242 int retval = 0; 1243 1244 if (!new_info || !info->ioaddr) 1245 return -ENODEV; 1246 if (copy_from_user(&new_serial, new_info, sizeof(new_serial))) 1247 return -EFAULT; 1248 1249 if (new_serial.irq != info->board->irq || 1250 new_serial.port != info->ioaddr) 1251 return -EINVAL; 1252 1253 flags = port->flags & ASYNC_SPD_MASK; 1254 1255 if (!capable(CAP_SYS_ADMIN)) { 1256 if ((new_serial.baud_base != info->baud_base) || 1257 (new_serial.close_delay != info->port.close_delay) || 1258 ((new_serial.flags & ~ASYNC_USR_MASK) != (info->port.flags & ~ASYNC_USR_MASK))) 1259 return -EPERM; 1260 info->port.flags = ((info->port.flags & ~ASYNC_USR_MASK) | 1261 (new_serial.flags & ASYNC_USR_MASK)); 1262 } else { 1263 /* 1264 * OK, past this point, all the error checking has been done. 1265 * At this point, we start making changes..... 1266 */ 1267 port->flags = ((port->flags & ~ASYNC_FLAGS) | 1268 (new_serial.flags & ASYNC_FLAGS)); 1269 port->close_delay = new_serial.close_delay * HZ / 100; 1270 port->closing_wait = new_serial.closing_wait * HZ / 100; 1271 port->low_latency = (port->flags & ASYNC_LOW_LATENCY) ? 1 : 0; 1272 if ((port->flags & ASYNC_SPD_MASK) == ASYNC_SPD_CUST && 1273 (new_serial.baud_base != info->baud_base || 1274 new_serial.custom_divisor != 1275 info->custom_divisor)) { 1276 if (new_serial.custom_divisor == 0) 1277 return -EINVAL; 1278 baud = new_serial.baud_base / new_serial.custom_divisor; 1279 tty_encode_baud_rate(tty, baud, baud); 1280 } 1281 } 1282 1283 info->type = new_serial.type; 1284 1285 process_txrx_fifo(info); 1286 1287 if (test_bit(ASYNCB_INITIALIZED, &port->flags)) { 1288 if (flags != (port->flags & ASYNC_SPD_MASK)) { 1289 spin_lock_irqsave(&info->slock, sl_flags); 1290 mxser_change_speed(tty, NULL); 1291 spin_unlock_irqrestore(&info->slock, sl_flags); 1292 } 1293 } else { 1294 retval = mxser_activate(port, tty); 1295 if (retval == 0) 1296 set_bit(ASYNCB_INITIALIZED, &port->flags); 1297 } 1298 return retval; 1299 } 1300 1301 /* 1302 * mxser_get_lsr_info - get line status register info 1303 * 1304 * Purpose: Let user call ioctl() to get info when the UART physically 1305 * is emptied. On bus types like RS485, the transmitter must 1306 * release the bus after transmitting. This must be done when 1307 * the transmit shift register is empty, not be done when the 1308 * transmit holding register is empty. This functionality 1309 * allows an RS485 driver to be written in user space. 1310 */ 1311 static int mxser_get_lsr_info(struct mxser_port *info, 1312 unsigned int __user *value) 1313 { 1314 unsigned char status; 1315 unsigned int result; 1316 unsigned long flags; 1317 1318 spin_lock_irqsave(&info->slock, flags); 1319 status = inb(info->ioaddr + UART_LSR); 1320 spin_unlock_irqrestore(&info->slock, flags); 1321 result = ((status & UART_LSR_TEMT) ? TIOCSER_TEMT : 0); 1322 return put_user(result, value); 1323 } 1324 1325 static int mxser_tiocmget(struct tty_struct *tty) 1326 { 1327 struct mxser_port *info = tty->driver_data; 1328 unsigned char control, status; 1329 unsigned long flags; 1330 1331 1332 if (tty->index == MXSER_PORTS) 1333 return -ENOIOCTLCMD; 1334 if (test_bit(TTY_IO_ERROR, &tty->flags)) 1335 return -EIO; 1336 1337 control = info->MCR; 1338 1339 spin_lock_irqsave(&info->slock, flags); 1340 status = inb(info->ioaddr + UART_MSR); 1341 if (status & UART_MSR_ANY_DELTA) 1342 mxser_check_modem_status(tty, info, status); 1343 spin_unlock_irqrestore(&info->slock, flags); 1344 return ((control & UART_MCR_RTS) ? TIOCM_RTS : 0) | 1345 ((control & UART_MCR_DTR) ? TIOCM_DTR : 0) | 1346 ((status & UART_MSR_DCD) ? TIOCM_CAR : 0) | 1347 ((status & UART_MSR_RI) ? TIOCM_RNG : 0) | 1348 ((status & UART_MSR_DSR) ? TIOCM_DSR : 0) | 1349 ((status & UART_MSR_CTS) ? TIOCM_CTS : 0); 1350 } 1351 1352 static int mxser_tiocmset(struct tty_struct *tty, 1353 unsigned int set, unsigned int clear) 1354 { 1355 struct mxser_port *info = tty->driver_data; 1356 unsigned long flags; 1357 1358 1359 if (tty->index == MXSER_PORTS) 1360 return -ENOIOCTLCMD; 1361 if (test_bit(TTY_IO_ERROR, &tty->flags)) 1362 return -EIO; 1363 1364 spin_lock_irqsave(&info->slock, flags); 1365 1366 if (set & TIOCM_RTS) 1367 info->MCR |= UART_MCR_RTS; 1368 if (set & TIOCM_DTR) 1369 info->MCR |= UART_MCR_DTR; 1370 1371 if (clear & TIOCM_RTS) 1372 info->MCR &= ~UART_MCR_RTS; 1373 if (clear & TIOCM_DTR) 1374 info->MCR &= ~UART_MCR_DTR; 1375 1376 outb(info->MCR, info->ioaddr + UART_MCR); 1377 spin_unlock_irqrestore(&info->slock, flags); 1378 return 0; 1379 } 1380 1381 static int __init mxser_program_mode(int port) 1382 { 1383 int id, i, j, n; 1384 1385 outb(0, port); 1386 outb(0, port); 1387 outb(0, port); 1388 (void)inb(port); 1389 (void)inb(port); 1390 outb(0, port); 1391 (void)inb(port); 1392 1393 id = inb(port + 1) & 0x1F; 1394 if ((id != C168_ASIC_ID) && 1395 (id != C104_ASIC_ID) && 1396 (id != C102_ASIC_ID) && 1397 (id != CI132_ASIC_ID) && 1398 (id != CI134_ASIC_ID) && 1399 (id != CI104J_ASIC_ID)) 1400 return -1; 1401 for (i = 0, j = 0; i < 4; i++) { 1402 n = inb(port + 2); 1403 if (n == 'M') { 1404 j = 1; 1405 } else if ((j == 1) && (n == 1)) { 1406 j = 2; 1407 break; 1408 } else 1409 j = 0; 1410 } 1411 if (j != 2) 1412 id = -2; 1413 return id; 1414 } 1415 1416 static void __init mxser_normal_mode(int port) 1417 { 1418 int i, n; 1419 1420 outb(0xA5, port + 1); 1421 outb(0x80, port + 3); 1422 outb(12, port + 0); /* 9600 bps */ 1423 outb(0, port + 1); 1424 outb(0x03, port + 3); /* 8 data bits */ 1425 outb(0x13, port + 4); /* loop back mode */ 1426 for (i = 0; i < 16; i++) { 1427 n = inb(port + 5); 1428 if ((n & 0x61) == 0x60) 1429 break; 1430 if ((n & 1) == 1) 1431 (void)inb(port); 1432 } 1433 outb(0x00, port + 4); 1434 } 1435 1436 #define CHIP_SK 0x01 /* Serial Data Clock in Eprom */ 1437 #define CHIP_DO 0x02 /* Serial Data Output in Eprom */ 1438 #define CHIP_CS 0x04 /* Serial Chip Select in Eprom */ 1439 #define CHIP_DI 0x08 /* Serial Data Input in Eprom */ 1440 #define EN_CCMD 0x000 /* Chip's command register */ 1441 #define EN0_RSARLO 0x008 /* Remote start address reg 0 */ 1442 #define EN0_RSARHI 0x009 /* Remote start address reg 1 */ 1443 #define EN0_RCNTLO 0x00A /* Remote byte count reg WR */ 1444 #define EN0_RCNTHI 0x00B /* Remote byte count reg WR */ 1445 #define EN0_DCFG 0x00E /* Data configuration reg WR */ 1446 #define EN0_PORT 0x010 /* Rcv missed frame error counter RD */ 1447 #define ENC_PAGE0 0x000 /* Select page 0 of chip registers */ 1448 #define ENC_PAGE3 0x0C0 /* Select page 3 of chip registers */ 1449 static int __init mxser_read_register(int port, unsigned short *regs) 1450 { 1451 int i, k, value, id; 1452 unsigned int j; 1453 1454 id = mxser_program_mode(port); 1455 if (id < 0) 1456 return id; 1457 for (i = 0; i < 14; i++) { 1458 k = (i & 0x3F) | 0x180; 1459 for (j = 0x100; j > 0; j >>= 1) { 1460 outb(CHIP_CS, port); 1461 if (k & j) { 1462 outb(CHIP_CS | CHIP_DO, port); 1463 outb(CHIP_CS | CHIP_DO | CHIP_SK, port); /* A? bit of read */ 1464 } else { 1465 outb(CHIP_CS, port); 1466 outb(CHIP_CS | CHIP_SK, port); /* A? bit of read */ 1467 } 1468 } 1469 (void)inb(port); 1470 value = 0; 1471 for (k = 0, j = 0x8000; k < 16; k++, j >>= 1) { 1472 outb(CHIP_CS, port); 1473 outb(CHIP_CS | CHIP_SK, port); 1474 if (inb(port) & CHIP_DI) 1475 value |= j; 1476 } 1477 regs[i] = value; 1478 outb(0, port); 1479 } 1480 mxser_normal_mode(port); 1481 return id; 1482 } 1483 1484 static int mxser_ioctl_special(unsigned int cmd, void __user *argp) 1485 { 1486 struct mxser_port *ip; 1487 struct tty_port *port; 1488 struct tty_struct *tty; 1489 int result, status; 1490 unsigned int i, j; 1491 int ret = 0; 1492 1493 switch (cmd) { 1494 case MOXA_GET_MAJOR: 1495 printk_ratelimited(KERN_WARNING "mxser: '%s' uses deprecated ioctl " 1496 "%x (GET_MAJOR), fix your userspace\n", 1497 current->comm, cmd); 1498 return put_user(ttymajor, (int __user *)argp); 1499 1500 case MOXA_CHKPORTENABLE: 1501 result = 0; 1502 for (i = 0; i < MXSER_BOARDS; i++) 1503 for (j = 0; j < MXSER_PORTS_PER_BOARD; j++) 1504 if (mxser_boards[i].ports[j].ioaddr) 1505 result |= (1 << i); 1506 return put_user(result, (unsigned long __user *)argp); 1507 case MOXA_GETDATACOUNT: 1508 /* The receive side is locked by port->slock but it isn't 1509 clear that an exact snapshot is worth copying here */ 1510 if (copy_to_user(argp, &mxvar_log, sizeof(mxvar_log))) 1511 ret = -EFAULT; 1512 return ret; 1513 case MOXA_GETMSTATUS: { 1514 struct mxser_mstatus ms, __user *msu = argp; 1515 for (i = 0; i < MXSER_BOARDS; i++) 1516 for (j = 0; j < MXSER_PORTS_PER_BOARD; j++) { 1517 ip = &mxser_boards[i].ports[j]; 1518 port = &ip->port; 1519 memset(&ms, 0, sizeof(ms)); 1520 1521 mutex_lock(&port->mutex); 1522 if (!ip->ioaddr) 1523 goto copy; 1524 1525 tty = tty_port_tty_get(port); 1526 1527 if (!tty) 1528 ms.cflag = ip->normal_termios.c_cflag; 1529 else 1530 ms.cflag = tty->termios.c_cflag; 1531 tty_kref_put(tty); 1532 spin_lock_irq(&ip->slock); 1533 status = inb(ip->ioaddr + UART_MSR); 1534 spin_unlock_irq(&ip->slock); 1535 if (status & UART_MSR_DCD) 1536 ms.dcd = 1; 1537 if (status & UART_MSR_DSR) 1538 ms.dsr = 1; 1539 if (status & UART_MSR_CTS) 1540 ms.cts = 1; 1541 copy: 1542 mutex_unlock(&port->mutex); 1543 if (copy_to_user(msu, &ms, sizeof(ms))) 1544 return -EFAULT; 1545 msu++; 1546 } 1547 return 0; 1548 } 1549 case MOXA_ASPP_MON_EXT: { 1550 struct mxser_mon_ext *me; /* it's 2k, stack unfriendly */ 1551 unsigned int cflag, iflag, p; 1552 u8 opmode; 1553 1554 me = kzalloc(sizeof(*me), GFP_KERNEL); 1555 if (!me) 1556 return -ENOMEM; 1557 1558 for (i = 0, p = 0; i < MXSER_BOARDS; i++) { 1559 for (j = 0; j < MXSER_PORTS_PER_BOARD; j++, p++) { 1560 if (p >= ARRAY_SIZE(me->rx_cnt)) { 1561 i = MXSER_BOARDS; 1562 break; 1563 } 1564 ip = &mxser_boards[i].ports[j]; 1565 port = &ip->port; 1566 1567 mutex_lock(&port->mutex); 1568 if (!ip->ioaddr) { 1569 mutex_unlock(&port->mutex); 1570 continue; 1571 } 1572 1573 spin_lock_irq(&ip->slock); 1574 status = mxser_get_msr(ip->ioaddr, 0, p); 1575 1576 if (status & UART_MSR_TERI) 1577 ip->icount.rng++; 1578 if (status & UART_MSR_DDSR) 1579 ip->icount.dsr++; 1580 if (status & UART_MSR_DDCD) 1581 ip->icount.dcd++; 1582 if (status & UART_MSR_DCTS) 1583 ip->icount.cts++; 1584 1585 ip->mon_data.modem_status = status; 1586 me->rx_cnt[p] = ip->mon_data.rxcnt; 1587 me->tx_cnt[p] = ip->mon_data.txcnt; 1588 me->up_rxcnt[p] = ip->mon_data.up_rxcnt; 1589 me->up_txcnt[p] = ip->mon_data.up_txcnt; 1590 me->modem_status[p] = 1591 ip->mon_data.modem_status; 1592 spin_unlock_irq(&ip->slock); 1593 1594 tty = tty_port_tty_get(&ip->port); 1595 1596 if (!tty) { 1597 cflag = ip->normal_termios.c_cflag; 1598 iflag = ip->normal_termios.c_iflag; 1599 me->baudrate[p] = tty_termios_baud_rate(&ip->normal_termios); 1600 } else { 1601 cflag = tty->termios.c_cflag; 1602 iflag = tty->termios.c_iflag; 1603 me->baudrate[p] = tty_get_baud_rate(tty); 1604 } 1605 tty_kref_put(tty); 1606 1607 me->databits[p] = cflag & CSIZE; 1608 me->stopbits[p] = cflag & CSTOPB; 1609 me->parity[p] = cflag & (PARENB | PARODD | 1610 CMSPAR); 1611 1612 if (cflag & CRTSCTS) 1613 me->flowctrl[p] |= 0x03; 1614 1615 if (iflag & (IXON | IXOFF)) 1616 me->flowctrl[p] |= 0x0C; 1617 1618 if (ip->type == PORT_16550A) 1619 me->fifo[p] = 1; 1620 1621 opmode = inb(ip->opmode_ioaddr)>>((p % 4) * 2); 1622 opmode &= OP_MODE_MASK; 1623 me->iftype[p] = opmode; 1624 mutex_unlock(&port->mutex); 1625 } 1626 } 1627 if (copy_to_user(argp, me, sizeof(*me))) 1628 ret = -EFAULT; 1629 kfree(me); 1630 return ret; 1631 } 1632 default: 1633 return -ENOIOCTLCMD; 1634 } 1635 return 0; 1636 } 1637 1638 static int mxser_cflags_changed(struct mxser_port *info, unsigned long arg, 1639 struct async_icount *cprev) 1640 { 1641 struct async_icount cnow; 1642 unsigned long flags; 1643 int ret; 1644 1645 spin_lock_irqsave(&info->slock, flags); 1646 cnow = info->icount; /* atomic copy */ 1647 spin_unlock_irqrestore(&info->slock, flags); 1648 1649 ret = ((arg & TIOCM_RNG) && (cnow.rng != cprev->rng)) || 1650 ((arg & TIOCM_DSR) && (cnow.dsr != cprev->dsr)) || 1651 ((arg & TIOCM_CD) && (cnow.dcd != cprev->dcd)) || 1652 ((arg & TIOCM_CTS) && (cnow.cts != cprev->cts)); 1653 1654 *cprev = cnow; 1655 1656 return ret; 1657 } 1658 1659 static int mxser_ioctl(struct tty_struct *tty, 1660 unsigned int cmd, unsigned long arg) 1661 { 1662 struct mxser_port *info = tty->driver_data; 1663 struct tty_port *port = &info->port; 1664 struct async_icount cnow; 1665 unsigned long flags; 1666 void __user *argp = (void __user *)arg; 1667 int retval; 1668 1669 if (tty->index == MXSER_PORTS) 1670 return mxser_ioctl_special(cmd, argp); 1671 1672 if (cmd == MOXA_SET_OP_MODE || cmd == MOXA_GET_OP_MODE) { 1673 int p; 1674 unsigned long opmode; 1675 static unsigned char ModeMask[] = { 0xfc, 0xf3, 0xcf, 0x3f }; 1676 int shiftbit; 1677 unsigned char val, mask; 1678 1679 p = tty->index % 4; 1680 if (cmd == MOXA_SET_OP_MODE) { 1681 if (get_user(opmode, (int __user *) argp)) 1682 return -EFAULT; 1683 if (opmode != RS232_MODE && 1684 opmode != RS485_2WIRE_MODE && 1685 opmode != RS422_MODE && 1686 opmode != RS485_4WIRE_MODE) 1687 return -EFAULT; 1688 mask = ModeMask[p]; 1689 shiftbit = p * 2; 1690 spin_lock_irq(&info->slock); 1691 val = inb(info->opmode_ioaddr); 1692 val &= mask; 1693 val |= (opmode << shiftbit); 1694 outb(val, info->opmode_ioaddr); 1695 spin_unlock_irq(&info->slock); 1696 } else { 1697 shiftbit = p * 2; 1698 spin_lock_irq(&info->slock); 1699 opmode = inb(info->opmode_ioaddr) >> shiftbit; 1700 spin_unlock_irq(&info->slock); 1701 opmode &= OP_MODE_MASK; 1702 if (put_user(opmode, (int __user *)argp)) 1703 return -EFAULT; 1704 } 1705 return 0; 1706 } 1707 1708 if (cmd != TIOCGSERIAL && cmd != TIOCMIWAIT && 1709 test_bit(TTY_IO_ERROR, &tty->flags)) 1710 return -EIO; 1711 1712 switch (cmd) { 1713 case TIOCGSERIAL: 1714 mutex_lock(&port->mutex); 1715 retval = mxser_get_serial_info(tty, argp); 1716 mutex_unlock(&port->mutex); 1717 return retval; 1718 case TIOCSSERIAL: 1719 mutex_lock(&port->mutex); 1720 retval = mxser_set_serial_info(tty, argp); 1721 mutex_unlock(&port->mutex); 1722 return retval; 1723 case TIOCSERGETLSR: /* Get line status register */ 1724 return mxser_get_lsr_info(info, argp); 1725 /* 1726 * Wait for any of the 4 modem inputs (DCD,RI,DSR,CTS) to change 1727 * - mask passed in arg for lines of interest 1728 * (use |'ed TIOCM_RNG/DSR/CD/CTS for masking) 1729 * Caller should use TIOCGICOUNT to see which one it was 1730 */ 1731 case TIOCMIWAIT: 1732 spin_lock_irqsave(&info->slock, flags); 1733 cnow = info->icount; /* note the counters on entry */ 1734 spin_unlock_irqrestore(&info->slock, flags); 1735 1736 return wait_event_interruptible(info->port.delta_msr_wait, 1737 mxser_cflags_changed(info, arg, &cnow)); 1738 case MOXA_HighSpeedOn: 1739 return put_user(info->baud_base != 115200 ? 1 : 0, (int __user *)argp); 1740 case MOXA_SDS_RSTICOUNTER: 1741 spin_lock_irq(&info->slock); 1742 info->mon_data.rxcnt = 0; 1743 info->mon_data.txcnt = 0; 1744 spin_unlock_irq(&info->slock); 1745 return 0; 1746 1747 case MOXA_ASPP_OQUEUE:{ 1748 int len, lsr; 1749 1750 len = mxser_chars_in_buffer(tty); 1751 spin_lock_irq(&info->slock); 1752 lsr = inb(info->ioaddr + UART_LSR) & UART_LSR_THRE; 1753 spin_unlock_irq(&info->slock); 1754 len += (lsr ? 0 : 1); 1755 1756 return put_user(len, (int __user *)argp); 1757 } 1758 case MOXA_ASPP_MON: { 1759 int mcr, status; 1760 1761 spin_lock_irq(&info->slock); 1762 status = mxser_get_msr(info->ioaddr, 1, tty->index); 1763 mxser_check_modem_status(tty, info, status); 1764 1765 mcr = inb(info->ioaddr + UART_MCR); 1766 spin_unlock_irq(&info->slock); 1767 1768 if (mcr & MOXA_MUST_MCR_XON_FLAG) 1769 info->mon_data.hold_reason &= ~NPPI_NOTIFY_XOFFHOLD; 1770 else 1771 info->mon_data.hold_reason |= NPPI_NOTIFY_XOFFHOLD; 1772 1773 if (mcr & MOXA_MUST_MCR_TX_XON) 1774 info->mon_data.hold_reason &= ~NPPI_NOTIFY_XOFFXENT; 1775 else 1776 info->mon_data.hold_reason |= NPPI_NOTIFY_XOFFXENT; 1777 1778 if (tty->hw_stopped) 1779 info->mon_data.hold_reason |= NPPI_NOTIFY_CTSHOLD; 1780 else 1781 info->mon_data.hold_reason &= ~NPPI_NOTIFY_CTSHOLD; 1782 1783 if (copy_to_user(argp, &info->mon_data, 1784 sizeof(struct mxser_mon))) 1785 return -EFAULT; 1786 1787 return 0; 1788 } 1789 case MOXA_ASPP_LSTATUS: { 1790 if (put_user(info->err_shadow, (unsigned char __user *)argp)) 1791 return -EFAULT; 1792 1793 info->err_shadow = 0; 1794 return 0; 1795 } 1796 case MOXA_SET_BAUD_METHOD: { 1797 int method; 1798 1799 if (get_user(method, (int __user *)argp)) 1800 return -EFAULT; 1801 mxser_set_baud_method[tty->index] = method; 1802 return put_user(method, (int __user *)argp); 1803 } 1804 default: 1805 return -ENOIOCTLCMD; 1806 } 1807 return 0; 1808 } 1809 1810 /* 1811 * Get counter of input serial line interrupts (DCD,RI,DSR,CTS) 1812 * Return: write counters to the user passed counter struct 1813 * NB: both 1->0 and 0->1 transitions are counted except for 1814 * RI where only 0->1 is counted. 1815 */ 1816 1817 static int mxser_get_icount(struct tty_struct *tty, 1818 struct serial_icounter_struct *icount) 1819 1820 { 1821 struct mxser_port *info = tty->driver_data; 1822 struct async_icount cnow; 1823 unsigned long flags; 1824 1825 spin_lock_irqsave(&info->slock, flags); 1826 cnow = info->icount; 1827 spin_unlock_irqrestore(&info->slock, flags); 1828 1829 icount->frame = cnow.frame; 1830 icount->brk = cnow.brk; 1831 icount->overrun = cnow.overrun; 1832 icount->buf_overrun = cnow.buf_overrun; 1833 icount->parity = cnow.parity; 1834 icount->rx = cnow.rx; 1835 icount->tx = cnow.tx; 1836 icount->cts = cnow.cts; 1837 icount->dsr = cnow.dsr; 1838 icount->rng = cnow.rng; 1839 icount->dcd = cnow.dcd; 1840 return 0; 1841 } 1842 1843 static void mxser_stoprx(struct tty_struct *tty) 1844 { 1845 struct mxser_port *info = tty->driver_data; 1846 1847 info->ldisc_stop_rx = 1; 1848 if (I_IXOFF(tty)) { 1849 if (info->board->chip_flag) { 1850 info->IER &= ~MOXA_MUST_RECV_ISR; 1851 outb(info->IER, info->ioaddr + UART_IER); 1852 } else { 1853 info->x_char = STOP_CHAR(tty); 1854 outb(0, info->ioaddr + UART_IER); 1855 info->IER |= UART_IER_THRI; 1856 outb(info->IER, info->ioaddr + UART_IER); 1857 } 1858 } 1859 1860 if (tty->termios.c_cflag & CRTSCTS) { 1861 info->MCR &= ~UART_MCR_RTS; 1862 outb(info->MCR, info->ioaddr + UART_MCR); 1863 } 1864 } 1865 1866 /* 1867 * This routine is called by the upper-layer tty layer to signal that 1868 * incoming characters should be throttled. 1869 */ 1870 static void mxser_throttle(struct tty_struct *tty) 1871 { 1872 mxser_stoprx(tty); 1873 } 1874 1875 static void mxser_unthrottle(struct tty_struct *tty) 1876 { 1877 struct mxser_port *info = tty->driver_data; 1878 1879 /* startrx */ 1880 info->ldisc_stop_rx = 0; 1881 if (I_IXOFF(tty)) { 1882 if (info->x_char) 1883 info->x_char = 0; 1884 else { 1885 if (info->board->chip_flag) { 1886 info->IER |= MOXA_MUST_RECV_ISR; 1887 outb(info->IER, info->ioaddr + UART_IER); 1888 } else { 1889 info->x_char = START_CHAR(tty); 1890 outb(0, info->ioaddr + UART_IER); 1891 info->IER |= UART_IER_THRI; 1892 outb(info->IER, info->ioaddr + UART_IER); 1893 } 1894 } 1895 } 1896 1897 if (tty->termios.c_cflag & CRTSCTS) { 1898 info->MCR |= UART_MCR_RTS; 1899 outb(info->MCR, info->ioaddr + UART_MCR); 1900 } 1901 } 1902 1903 /* 1904 * mxser_stop() and mxser_start() 1905 * 1906 * This routines are called before setting or resetting tty->stopped. 1907 * They enable or disable transmitter interrupts, as necessary. 1908 */ 1909 static void mxser_stop(struct tty_struct *tty) 1910 { 1911 struct mxser_port *info = tty->driver_data; 1912 unsigned long flags; 1913 1914 spin_lock_irqsave(&info->slock, flags); 1915 if (info->IER & UART_IER_THRI) { 1916 info->IER &= ~UART_IER_THRI; 1917 outb(info->IER, info->ioaddr + UART_IER); 1918 } 1919 spin_unlock_irqrestore(&info->slock, flags); 1920 } 1921 1922 static void mxser_start(struct tty_struct *tty) 1923 { 1924 struct mxser_port *info = tty->driver_data; 1925 unsigned long flags; 1926 1927 spin_lock_irqsave(&info->slock, flags); 1928 if (info->xmit_cnt && info->port.xmit_buf) { 1929 outb(info->IER & ~UART_IER_THRI, info->ioaddr + UART_IER); 1930 info->IER |= UART_IER_THRI; 1931 outb(info->IER, info->ioaddr + UART_IER); 1932 } 1933 spin_unlock_irqrestore(&info->slock, flags); 1934 } 1935 1936 static void mxser_set_termios(struct tty_struct *tty, struct ktermios *old_termios) 1937 { 1938 struct mxser_port *info = tty->driver_data; 1939 unsigned long flags; 1940 1941 spin_lock_irqsave(&info->slock, flags); 1942 mxser_change_speed(tty, old_termios); 1943 spin_unlock_irqrestore(&info->slock, flags); 1944 1945 if ((old_termios->c_cflag & CRTSCTS) && 1946 !(tty->termios.c_cflag & CRTSCTS)) { 1947 tty->hw_stopped = 0; 1948 mxser_start(tty); 1949 } 1950 1951 /* Handle sw stopped */ 1952 if ((old_termios->c_iflag & IXON) && 1953 !(tty->termios.c_iflag & IXON)) { 1954 tty->stopped = 0; 1955 1956 if (info->board->chip_flag) { 1957 spin_lock_irqsave(&info->slock, flags); 1958 mxser_disable_must_rx_software_flow_control( 1959 info->ioaddr); 1960 spin_unlock_irqrestore(&info->slock, flags); 1961 } 1962 1963 mxser_start(tty); 1964 } 1965 } 1966 1967 /* 1968 * mxser_wait_until_sent() --- wait until the transmitter is empty 1969 */ 1970 static void mxser_wait_until_sent(struct tty_struct *tty, int timeout) 1971 { 1972 struct mxser_port *info = tty->driver_data; 1973 unsigned long orig_jiffies, char_time; 1974 unsigned long flags; 1975 int lsr; 1976 1977 if (info->type == PORT_UNKNOWN) 1978 return; 1979 1980 if (info->xmit_fifo_size == 0) 1981 return; /* Just in case.... */ 1982 1983 orig_jiffies = jiffies; 1984 /* 1985 * Set the check interval to be 1/5 of the estimated time to 1986 * send a single character, and make it at least 1. The check 1987 * interval should also be less than the timeout. 1988 * 1989 * Note: we have to use pretty tight timings here to satisfy 1990 * the NIST-PCTS. 1991 */ 1992 char_time = (info->timeout - HZ / 50) / info->xmit_fifo_size; 1993 char_time = char_time / 5; 1994 if (char_time == 0) 1995 char_time = 1; 1996 if (timeout && timeout < char_time) 1997 char_time = timeout; 1998 /* 1999 * If the transmitter hasn't cleared in twice the approximate 2000 * amount of time to send the entire FIFO, it probably won't 2001 * ever clear. This assumes the UART isn't doing flow 2002 * control, which is currently the case. Hence, if it ever 2003 * takes longer than info->timeout, this is probably due to a 2004 * UART bug of some kind. So, we clamp the timeout parameter at 2005 * 2*info->timeout. 2006 */ 2007 if (!timeout || timeout > 2 * info->timeout) 2008 timeout = 2 * info->timeout; 2009 2010 spin_lock_irqsave(&info->slock, flags); 2011 while (!((lsr = inb(info->ioaddr + UART_LSR)) & UART_LSR_TEMT)) { 2012 spin_unlock_irqrestore(&info->slock, flags); 2013 schedule_timeout_interruptible(char_time); 2014 spin_lock_irqsave(&info->slock, flags); 2015 if (signal_pending(current)) 2016 break; 2017 if (timeout && time_after(jiffies, orig_jiffies + timeout)) 2018 break; 2019 } 2020 spin_unlock_irqrestore(&info->slock, flags); 2021 set_current_state(TASK_RUNNING); 2022 } 2023 2024 /* 2025 * This routine is called by tty_hangup() when a hangup is signaled. 2026 */ 2027 static void mxser_hangup(struct tty_struct *tty) 2028 { 2029 struct mxser_port *info = tty->driver_data; 2030 2031 mxser_flush_buffer(tty); 2032 tty_port_hangup(&info->port); 2033 } 2034 2035 /* 2036 * mxser_rs_break() --- routine which turns the break handling on or off 2037 */ 2038 static int mxser_rs_break(struct tty_struct *tty, int break_state) 2039 { 2040 struct mxser_port *info = tty->driver_data; 2041 unsigned long flags; 2042 2043 spin_lock_irqsave(&info->slock, flags); 2044 if (break_state == -1) 2045 outb(inb(info->ioaddr + UART_LCR) | UART_LCR_SBC, 2046 info->ioaddr + UART_LCR); 2047 else 2048 outb(inb(info->ioaddr + UART_LCR) & ~UART_LCR_SBC, 2049 info->ioaddr + UART_LCR); 2050 spin_unlock_irqrestore(&info->slock, flags); 2051 return 0; 2052 } 2053 2054 static void mxser_receive_chars(struct tty_struct *tty, 2055 struct mxser_port *port, int *status) 2056 { 2057 unsigned char ch, gdl; 2058 int ignored = 0; 2059 int cnt = 0; 2060 int recv_room; 2061 int max = 256; 2062 2063 recv_room = tty->receive_room; 2064 if (recv_room == 0 && !port->ldisc_stop_rx) 2065 mxser_stoprx(tty); 2066 if (port->board->chip_flag != MOXA_OTHER_UART) { 2067 2068 if (*status & UART_LSR_SPECIAL) 2069 goto intr_old; 2070 if (port->board->chip_flag == MOXA_MUST_MU860_HWID && 2071 (*status & MOXA_MUST_LSR_RERR)) 2072 goto intr_old; 2073 if (*status & MOXA_MUST_LSR_RERR) 2074 goto intr_old; 2075 2076 gdl = inb(port->ioaddr + MOXA_MUST_GDL_REGISTER); 2077 2078 if (port->board->chip_flag == MOXA_MUST_MU150_HWID) 2079 gdl &= MOXA_MUST_GDL_MASK; 2080 if (gdl >= recv_room) { 2081 if (!port->ldisc_stop_rx) 2082 mxser_stoprx(tty); 2083 } 2084 while (gdl--) { 2085 ch = inb(port->ioaddr + UART_RX); 2086 tty_insert_flip_char(&port->port, ch, 0); 2087 cnt++; 2088 } 2089 goto end_intr; 2090 } 2091 intr_old: 2092 2093 do { 2094 if (max-- < 0) 2095 break; 2096 2097 ch = inb(port->ioaddr + UART_RX); 2098 if (port->board->chip_flag && (*status & UART_LSR_OE)) 2099 outb(0x23, port->ioaddr + UART_FCR); 2100 *status &= port->read_status_mask; 2101 if (*status & port->ignore_status_mask) { 2102 if (++ignored > 100) 2103 break; 2104 } else { 2105 char flag = 0; 2106 if (*status & UART_LSR_SPECIAL) { 2107 if (*status & UART_LSR_BI) { 2108 flag = TTY_BREAK; 2109 port->icount.brk++; 2110 2111 if (port->port.flags & ASYNC_SAK) 2112 do_SAK(tty); 2113 } else if (*status & UART_LSR_PE) { 2114 flag = TTY_PARITY; 2115 port->icount.parity++; 2116 } else if (*status & UART_LSR_FE) { 2117 flag = TTY_FRAME; 2118 port->icount.frame++; 2119 } else if (*status & UART_LSR_OE) { 2120 flag = TTY_OVERRUN; 2121 port->icount.overrun++; 2122 } else 2123 flag = TTY_BREAK; 2124 } 2125 tty_insert_flip_char(&port->port, ch, flag); 2126 cnt++; 2127 if (cnt >= recv_room) { 2128 if (!port->ldisc_stop_rx) 2129 mxser_stoprx(tty); 2130 break; 2131 } 2132 2133 } 2134 2135 if (port->board->chip_flag) 2136 break; 2137 2138 *status = inb(port->ioaddr + UART_LSR); 2139 } while (*status & UART_LSR_DR); 2140 2141 end_intr: 2142 mxvar_log.rxcnt[tty->index] += cnt; 2143 port->mon_data.rxcnt += cnt; 2144 port->mon_data.up_rxcnt += cnt; 2145 2146 /* 2147 * We are called from an interrupt context with &port->slock 2148 * being held. Drop it temporarily in order to prevent 2149 * recursive locking. 2150 */ 2151 spin_unlock(&port->slock); 2152 tty_flip_buffer_push(&port->port); 2153 spin_lock(&port->slock); 2154 } 2155 2156 static void mxser_transmit_chars(struct tty_struct *tty, struct mxser_port *port) 2157 { 2158 int count, cnt; 2159 2160 if (port->x_char) { 2161 outb(port->x_char, port->ioaddr + UART_TX); 2162 port->x_char = 0; 2163 mxvar_log.txcnt[tty->index]++; 2164 port->mon_data.txcnt++; 2165 port->mon_data.up_txcnt++; 2166 port->icount.tx++; 2167 return; 2168 } 2169 2170 if (port->port.xmit_buf == NULL) 2171 return; 2172 2173 if (port->xmit_cnt <= 0 || tty->stopped || 2174 (tty->hw_stopped && 2175 (port->type != PORT_16550A) && 2176 (!port->board->chip_flag))) { 2177 port->IER &= ~UART_IER_THRI; 2178 outb(port->IER, port->ioaddr + UART_IER); 2179 return; 2180 } 2181 2182 cnt = port->xmit_cnt; 2183 count = port->xmit_fifo_size; 2184 do { 2185 outb(port->port.xmit_buf[port->xmit_tail++], 2186 port->ioaddr + UART_TX); 2187 port->xmit_tail = port->xmit_tail & (SERIAL_XMIT_SIZE - 1); 2188 if (--port->xmit_cnt <= 0) 2189 break; 2190 } while (--count > 0); 2191 mxvar_log.txcnt[tty->index] += (cnt - port->xmit_cnt); 2192 2193 port->mon_data.txcnt += (cnt - port->xmit_cnt); 2194 port->mon_data.up_txcnt += (cnt - port->xmit_cnt); 2195 port->icount.tx += (cnt - port->xmit_cnt); 2196 2197 if (port->xmit_cnt < WAKEUP_CHARS) 2198 tty_wakeup(tty); 2199 2200 if (port->xmit_cnt <= 0) { 2201 port->IER &= ~UART_IER_THRI; 2202 outb(port->IER, port->ioaddr + UART_IER); 2203 } 2204 } 2205 2206 /* 2207 * This is the serial driver's generic interrupt routine 2208 */ 2209 static irqreturn_t mxser_interrupt(int irq, void *dev_id) 2210 { 2211 int status, iir, i; 2212 struct mxser_board *brd = NULL; 2213 struct mxser_port *port; 2214 int max, irqbits, bits, msr; 2215 unsigned int int_cnt, pass_counter = 0; 2216 int handled = IRQ_NONE; 2217 struct tty_struct *tty; 2218 2219 for (i = 0; i < MXSER_BOARDS; i++) 2220 if (dev_id == &mxser_boards[i]) { 2221 brd = dev_id; 2222 break; 2223 } 2224 2225 if (i == MXSER_BOARDS) 2226 goto irq_stop; 2227 if (brd == NULL) 2228 goto irq_stop; 2229 max = brd->info->nports; 2230 while (pass_counter++ < MXSER_ISR_PASS_LIMIT) { 2231 irqbits = inb(brd->vector) & brd->vector_mask; 2232 if (irqbits == brd->vector_mask) 2233 break; 2234 2235 handled = IRQ_HANDLED; 2236 for (i = 0, bits = 1; i < max; i++, irqbits |= bits, bits <<= 1) { 2237 if (irqbits == brd->vector_mask) 2238 break; 2239 if (bits & irqbits) 2240 continue; 2241 port = &brd->ports[i]; 2242 2243 int_cnt = 0; 2244 spin_lock(&port->slock); 2245 do { 2246 iir = inb(port->ioaddr + UART_IIR); 2247 if (iir & UART_IIR_NO_INT) 2248 break; 2249 iir &= MOXA_MUST_IIR_MASK; 2250 tty = tty_port_tty_get(&port->port); 2251 if (!tty || 2252 (port->port.flags & ASYNC_CLOSING) || 2253 !(port->port.flags & 2254 ASYNC_INITIALIZED)) { 2255 status = inb(port->ioaddr + UART_LSR); 2256 outb(0x27, port->ioaddr + UART_FCR); 2257 inb(port->ioaddr + UART_MSR); 2258 tty_kref_put(tty); 2259 break; 2260 } 2261 2262 status = inb(port->ioaddr + UART_LSR); 2263 2264 if (status & UART_LSR_PE) 2265 port->err_shadow |= NPPI_NOTIFY_PARITY; 2266 if (status & UART_LSR_FE) 2267 port->err_shadow |= NPPI_NOTIFY_FRAMING; 2268 if (status & UART_LSR_OE) 2269 port->err_shadow |= 2270 NPPI_NOTIFY_HW_OVERRUN; 2271 if (status & UART_LSR_BI) 2272 port->err_shadow |= NPPI_NOTIFY_BREAK; 2273 2274 if (port->board->chip_flag) { 2275 if (iir == MOXA_MUST_IIR_GDA || 2276 iir == MOXA_MUST_IIR_RDA || 2277 iir == MOXA_MUST_IIR_RTO || 2278 iir == MOXA_MUST_IIR_LSR) 2279 mxser_receive_chars(tty, port, 2280 &status); 2281 2282 } else { 2283 status &= port->read_status_mask; 2284 if (status & UART_LSR_DR) 2285 mxser_receive_chars(tty, port, 2286 &status); 2287 } 2288 msr = inb(port->ioaddr + UART_MSR); 2289 if (msr & UART_MSR_ANY_DELTA) 2290 mxser_check_modem_status(tty, port, msr); 2291 2292 if (port->board->chip_flag) { 2293 if (iir == 0x02 && (status & 2294 UART_LSR_THRE)) 2295 mxser_transmit_chars(tty, port); 2296 } else { 2297 if (status & UART_LSR_THRE) 2298 mxser_transmit_chars(tty, port); 2299 } 2300 tty_kref_put(tty); 2301 } while (int_cnt++ < MXSER_ISR_PASS_LIMIT); 2302 spin_unlock(&port->slock); 2303 } 2304 } 2305 2306 irq_stop: 2307 return handled; 2308 } 2309 2310 static const struct tty_operations mxser_ops = { 2311 .open = mxser_open, 2312 .close = mxser_close, 2313 .write = mxser_write, 2314 .put_char = mxser_put_char, 2315 .flush_chars = mxser_flush_chars, 2316 .write_room = mxser_write_room, 2317 .chars_in_buffer = mxser_chars_in_buffer, 2318 .flush_buffer = mxser_flush_buffer, 2319 .ioctl = mxser_ioctl, 2320 .throttle = mxser_throttle, 2321 .unthrottle = mxser_unthrottle, 2322 .set_termios = mxser_set_termios, 2323 .stop = mxser_stop, 2324 .start = mxser_start, 2325 .hangup = mxser_hangup, 2326 .break_ctl = mxser_rs_break, 2327 .wait_until_sent = mxser_wait_until_sent, 2328 .tiocmget = mxser_tiocmget, 2329 .tiocmset = mxser_tiocmset, 2330 .get_icount = mxser_get_icount, 2331 }; 2332 2333 static struct tty_port_operations mxser_port_ops = { 2334 .carrier_raised = mxser_carrier_raised, 2335 .dtr_rts = mxser_dtr_rts, 2336 .activate = mxser_activate, 2337 .shutdown = mxser_shutdown_port, 2338 }; 2339 2340 /* 2341 * The MOXA Smartio/Industio serial driver boot-time initialization code! 2342 */ 2343 2344 static bool allow_overlapping_vector; 2345 module_param(allow_overlapping_vector, bool, S_IRUGO); 2346 MODULE_PARM_DESC(allow_overlapping_vector, "whether we allow ISA cards to be configured such that vector overlabs IO ports (default=no)"); 2347 2348 static bool mxser_overlapping_vector(struct mxser_board *brd) 2349 { 2350 return allow_overlapping_vector && 2351 brd->vector >= brd->ports[0].ioaddr && 2352 brd->vector < brd->ports[0].ioaddr + 8 * brd->info->nports; 2353 } 2354 2355 static int mxser_request_vector(struct mxser_board *brd) 2356 { 2357 if (mxser_overlapping_vector(brd)) 2358 return 0; 2359 return request_region(brd->vector, 1, "mxser(vector)") ? 0 : -EIO; 2360 } 2361 2362 static void mxser_release_vector(struct mxser_board *brd) 2363 { 2364 if (mxser_overlapping_vector(brd)) 2365 return; 2366 release_region(brd->vector, 1); 2367 } 2368 2369 static void mxser_release_ISA_res(struct mxser_board *brd) 2370 { 2371 release_region(brd->ports[0].ioaddr, 8 * brd->info->nports); 2372 mxser_release_vector(brd); 2373 } 2374 2375 static int mxser_initbrd(struct mxser_board *brd, 2376 struct pci_dev *pdev) 2377 { 2378 struct mxser_port *info; 2379 unsigned int i; 2380 int retval; 2381 2382 printk(KERN_INFO "mxser: max. baud rate = %d bps\n", 2383 brd->ports[0].max_baud); 2384 2385 for (i = 0; i < brd->info->nports; i++) { 2386 info = &brd->ports[i]; 2387 tty_port_init(&info->port); 2388 info->port.ops = &mxser_port_ops; 2389 info->board = brd; 2390 info->stop_rx = 0; 2391 info->ldisc_stop_rx = 0; 2392 2393 /* Enhance mode enabled here */ 2394 if (brd->chip_flag != MOXA_OTHER_UART) 2395 mxser_enable_must_enchance_mode(info->ioaddr); 2396 2397 info->port.flags = ASYNC_SHARE_IRQ; 2398 info->type = brd->uart_type; 2399 2400 process_txrx_fifo(info); 2401 2402 info->custom_divisor = info->baud_base * 16; 2403 info->port.close_delay = 5 * HZ / 10; 2404 info->port.closing_wait = 30 * HZ; 2405 info->normal_termios = mxvar_sdriver->init_termios; 2406 memset(&info->mon_data, 0, sizeof(struct mxser_mon)); 2407 info->err_shadow = 0; 2408 spin_lock_init(&info->slock); 2409 2410 /* before set INT ISR, disable all int */ 2411 outb(inb(info->ioaddr + UART_IER) & 0xf0, 2412 info->ioaddr + UART_IER); 2413 } 2414 2415 retval = request_irq(brd->irq, mxser_interrupt, IRQF_SHARED, "mxser", 2416 brd); 2417 if (retval) { 2418 for (i = 0; i < brd->info->nports; i++) 2419 tty_port_destroy(&brd->ports[i].port); 2420 printk(KERN_ERR "Board %s: Request irq failed, IRQ (%d) may " 2421 "conflict with another device.\n", 2422 brd->info->name, brd->irq); 2423 } 2424 2425 return retval; 2426 } 2427 2428 static void mxser_board_remove(struct mxser_board *brd) 2429 { 2430 unsigned int i; 2431 2432 for (i = 0; i < brd->info->nports; i++) { 2433 tty_unregister_device(mxvar_sdriver, brd->idx + i); 2434 tty_port_destroy(&brd->ports[i].port); 2435 } 2436 free_irq(brd->irq, brd); 2437 } 2438 2439 static int __init mxser_get_ISA_conf(int cap, struct mxser_board *brd) 2440 { 2441 int id, i, bits, ret; 2442 unsigned short regs[16], irq; 2443 unsigned char scratch, scratch2; 2444 2445 brd->chip_flag = MOXA_OTHER_UART; 2446 2447 id = mxser_read_register(cap, regs); 2448 switch (id) { 2449 case C168_ASIC_ID: 2450 brd->info = &mxser_cards[0]; 2451 break; 2452 case C104_ASIC_ID: 2453 brd->info = &mxser_cards[1]; 2454 break; 2455 case CI104J_ASIC_ID: 2456 brd->info = &mxser_cards[2]; 2457 break; 2458 case C102_ASIC_ID: 2459 brd->info = &mxser_cards[5]; 2460 break; 2461 case CI132_ASIC_ID: 2462 brd->info = &mxser_cards[6]; 2463 break; 2464 case CI134_ASIC_ID: 2465 brd->info = &mxser_cards[7]; 2466 break; 2467 default: 2468 return 0; 2469 } 2470 2471 irq = 0; 2472 /* some ISA cards have 2 ports, but we want to see them as 4-port (why?) 2473 Flag-hack checks if configuration should be read as 2-port here. */ 2474 if (brd->info->nports == 2 || (brd->info->flags & MXSER_HAS2)) { 2475 irq = regs[9] & 0xF000; 2476 irq = irq | (irq >> 4); 2477 if (irq != (regs[9] & 0xFF00)) 2478 goto err_irqconflict; 2479 } else if (brd->info->nports == 4) { 2480 irq = regs[9] & 0xF000; 2481 irq = irq | (irq >> 4); 2482 irq = irq | (irq >> 8); 2483 if (irq != regs[9]) 2484 goto err_irqconflict; 2485 } else if (brd->info->nports == 8) { 2486 irq = regs[9] & 0xF000; 2487 irq = irq | (irq >> 4); 2488 irq = irq | (irq >> 8); 2489 if ((irq != regs[9]) || (irq != regs[10])) 2490 goto err_irqconflict; 2491 } 2492 2493 if (!irq) { 2494 printk(KERN_ERR "mxser: interrupt number unset\n"); 2495 return -EIO; 2496 } 2497 brd->irq = ((int)(irq & 0xF000) >> 12); 2498 for (i = 0; i < 8; i++) 2499 brd->ports[i].ioaddr = (int) regs[i + 1] & 0xFFF8; 2500 if ((regs[12] & 0x80) == 0) { 2501 printk(KERN_ERR "mxser: invalid interrupt vector\n"); 2502 return -EIO; 2503 } 2504 brd->vector = (int)regs[11]; /* interrupt vector */ 2505 if (id == 1) 2506 brd->vector_mask = 0x00FF; 2507 else 2508 brd->vector_mask = 0x000F; 2509 for (i = 7, bits = 0x0100; i >= 0; i--, bits <<= 1) { 2510 if (regs[12] & bits) { 2511 brd->ports[i].baud_base = 921600; 2512 brd->ports[i].max_baud = 921600; 2513 } else { 2514 brd->ports[i].baud_base = 115200; 2515 brd->ports[i].max_baud = 115200; 2516 } 2517 } 2518 scratch2 = inb(cap + UART_LCR) & (~UART_LCR_DLAB); 2519 outb(scratch2 | UART_LCR_DLAB, cap + UART_LCR); 2520 outb(0, cap + UART_EFR); /* EFR is the same as FCR */ 2521 outb(scratch2, cap + UART_LCR); 2522 outb(UART_FCR_ENABLE_FIFO, cap + UART_FCR); 2523 scratch = inb(cap + UART_IIR); 2524 2525 if (scratch & 0xC0) 2526 brd->uart_type = PORT_16550A; 2527 else 2528 brd->uart_type = PORT_16450; 2529 if (!request_region(brd->ports[0].ioaddr, 8 * brd->info->nports, 2530 "mxser(IO)")) { 2531 printk(KERN_ERR "mxser: can't request ports I/O region: " 2532 "0x%.8lx-0x%.8lx\n", 2533 brd->ports[0].ioaddr, brd->ports[0].ioaddr + 2534 8 * brd->info->nports - 1); 2535 return -EIO; 2536 } 2537 2538 ret = mxser_request_vector(brd); 2539 if (ret) { 2540 release_region(brd->ports[0].ioaddr, 8 * brd->info->nports); 2541 printk(KERN_ERR "mxser: can't request interrupt vector region: " 2542 "0x%.8lx-0x%.8lx\n", 2543 brd->ports[0].ioaddr, brd->ports[0].ioaddr + 2544 8 * brd->info->nports - 1); 2545 return ret; 2546 } 2547 return brd->info->nports; 2548 2549 err_irqconflict: 2550 printk(KERN_ERR "mxser: invalid interrupt number\n"); 2551 return -EIO; 2552 } 2553 2554 static int mxser_probe(struct pci_dev *pdev, 2555 const struct pci_device_id *ent) 2556 { 2557 #ifdef CONFIG_PCI 2558 struct mxser_board *brd; 2559 unsigned int i, j; 2560 unsigned long ioaddress; 2561 struct device *tty_dev; 2562 int retval = -EINVAL; 2563 2564 for (i = 0; i < MXSER_BOARDS; i++) 2565 if (mxser_boards[i].info == NULL) 2566 break; 2567 2568 if (i >= MXSER_BOARDS) { 2569 dev_err(&pdev->dev, "too many boards found (maximum %d), board " 2570 "not configured\n", MXSER_BOARDS); 2571 goto err; 2572 } 2573 2574 brd = &mxser_boards[i]; 2575 brd->idx = i * MXSER_PORTS_PER_BOARD; 2576 dev_info(&pdev->dev, "found MOXA %s board (BusNo=%d, DevNo=%d)\n", 2577 mxser_cards[ent->driver_data].name, 2578 pdev->bus->number, PCI_SLOT(pdev->devfn)); 2579 2580 retval = pci_enable_device(pdev); 2581 if (retval) { 2582 dev_err(&pdev->dev, "PCI enable failed\n"); 2583 goto err; 2584 } 2585 2586 /* io address */ 2587 ioaddress = pci_resource_start(pdev, 2); 2588 retval = pci_request_region(pdev, 2, "mxser(IO)"); 2589 if (retval) 2590 goto err_dis; 2591 2592 brd->info = &mxser_cards[ent->driver_data]; 2593 for (i = 0; i < brd->info->nports; i++) 2594 brd->ports[i].ioaddr = ioaddress + 8 * i; 2595 2596 /* vector */ 2597 ioaddress = pci_resource_start(pdev, 3); 2598 retval = pci_request_region(pdev, 3, "mxser(vector)"); 2599 if (retval) 2600 goto err_zero; 2601 brd->vector = ioaddress; 2602 2603 /* irq */ 2604 brd->irq = pdev->irq; 2605 2606 brd->chip_flag = CheckIsMoxaMust(brd->ports[0].ioaddr); 2607 brd->uart_type = PORT_16550A; 2608 brd->vector_mask = 0; 2609 2610 for (i = 0; i < brd->info->nports; i++) { 2611 for (j = 0; j < UART_INFO_NUM; j++) { 2612 if (Gpci_uart_info[j].type == brd->chip_flag) { 2613 brd->ports[i].max_baud = 2614 Gpci_uart_info[j].max_baud; 2615 2616 /* exception....CP-102 */ 2617 if (brd->info->flags & MXSER_HIGHBAUD) 2618 brd->ports[i].max_baud = 921600; 2619 break; 2620 } 2621 } 2622 } 2623 2624 if (brd->chip_flag == MOXA_MUST_MU860_HWID) { 2625 for (i = 0; i < brd->info->nports; i++) { 2626 if (i < 4) 2627 brd->ports[i].opmode_ioaddr = ioaddress + 4; 2628 else 2629 brd->ports[i].opmode_ioaddr = ioaddress + 0x0c; 2630 } 2631 outb(0, ioaddress + 4); /* default set to RS232 mode */ 2632 outb(0, ioaddress + 0x0c); /* default set to RS232 mode */ 2633 } 2634 2635 for (i = 0; i < brd->info->nports; i++) { 2636 brd->vector_mask |= (1 << i); 2637 brd->ports[i].baud_base = 921600; 2638 } 2639 2640 /* mxser_initbrd will hook ISR. */ 2641 retval = mxser_initbrd(brd, pdev); 2642 if (retval) 2643 goto err_rel3; 2644 2645 for (i = 0; i < brd->info->nports; i++) { 2646 tty_dev = tty_port_register_device(&brd->ports[i].port, 2647 mxvar_sdriver, brd->idx + i, &pdev->dev); 2648 if (IS_ERR(tty_dev)) { 2649 retval = PTR_ERR(tty_dev); 2650 for (; i > 0; i--) 2651 tty_unregister_device(mxvar_sdriver, 2652 brd->idx + i - 1); 2653 goto err_relbrd; 2654 } 2655 } 2656 2657 pci_set_drvdata(pdev, brd); 2658 2659 return 0; 2660 err_relbrd: 2661 for (i = 0; i < brd->info->nports; i++) 2662 tty_port_destroy(&brd->ports[i].port); 2663 free_irq(brd->irq, brd); 2664 err_rel3: 2665 pci_release_region(pdev, 3); 2666 err_zero: 2667 brd->info = NULL; 2668 pci_release_region(pdev, 2); 2669 err_dis: 2670 pci_disable_device(pdev); 2671 err: 2672 return retval; 2673 #else 2674 return -ENODEV; 2675 #endif 2676 } 2677 2678 static void mxser_remove(struct pci_dev *pdev) 2679 { 2680 #ifdef CONFIG_PCI 2681 struct mxser_board *brd = pci_get_drvdata(pdev); 2682 2683 mxser_board_remove(brd); 2684 2685 pci_release_region(pdev, 2); 2686 pci_release_region(pdev, 3); 2687 pci_disable_device(pdev); 2688 brd->info = NULL; 2689 #endif 2690 } 2691 2692 static struct pci_driver mxser_driver = { 2693 .name = "mxser", 2694 .id_table = mxser_pcibrds, 2695 .probe = mxser_probe, 2696 .remove = mxser_remove 2697 }; 2698 2699 static int __init mxser_module_init(void) 2700 { 2701 struct mxser_board *brd; 2702 struct device *tty_dev; 2703 unsigned int b, i, m; 2704 int retval; 2705 2706 mxvar_sdriver = alloc_tty_driver(MXSER_PORTS + 1); 2707 if (!mxvar_sdriver) 2708 return -ENOMEM; 2709 2710 printk(KERN_INFO "MOXA Smartio/Industio family driver version %s\n", 2711 MXSER_VERSION); 2712 2713 /* Initialize the tty_driver structure */ 2714 mxvar_sdriver->name = "ttyMI"; 2715 mxvar_sdriver->major = ttymajor; 2716 mxvar_sdriver->minor_start = 0; 2717 mxvar_sdriver->type = TTY_DRIVER_TYPE_SERIAL; 2718 mxvar_sdriver->subtype = SERIAL_TYPE_NORMAL; 2719 mxvar_sdriver->init_termios = tty_std_termios; 2720 mxvar_sdriver->init_termios.c_cflag = B9600|CS8|CREAD|HUPCL|CLOCAL; 2721 mxvar_sdriver->flags = TTY_DRIVER_REAL_RAW|TTY_DRIVER_DYNAMIC_DEV; 2722 tty_set_operations(mxvar_sdriver, &mxser_ops); 2723 2724 retval = tty_register_driver(mxvar_sdriver); 2725 if (retval) { 2726 printk(KERN_ERR "Couldn't install MOXA Smartio/Industio family " 2727 "tty driver !\n"); 2728 goto err_put; 2729 } 2730 2731 /* Start finding ISA boards here */ 2732 for (m = 0, b = 0; b < MXSER_BOARDS; b++) { 2733 if (!ioaddr[b]) 2734 continue; 2735 2736 brd = &mxser_boards[m]; 2737 retval = mxser_get_ISA_conf(ioaddr[b], brd); 2738 if (retval <= 0) { 2739 brd->info = NULL; 2740 continue; 2741 } 2742 2743 printk(KERN_INFO "mxser: found MOXA %s board (CAP=0x%lx)\n", 2744 brd->info->name, ioaddr[b]); 2745 2746 /* mxser_initbrd will hook ISR. */ 2747 if (mxser_initbrd(brd, NULL) < 0) { 2748 mxser_release_ISA_res(brd); 2749 brd->info = NULL; 2750 continue; 2751 } 2752 2753 brd->idx = m * MXSER_PORTS_PER_BOARD; 2754 for (i = 0; i < brd->info->nports; i++) { 2755 tty_dev = tty_port_register_device(&brd->ports[i].port, 2756 mxvar_sdriver, brd->idx + i, NULL); 2757 if (IS_ERR(tty_dev)) { 2758 for (; i > 0; i--) 2759 tty_unregister_device(mxvar_sdriver, 2760 brd->idx + i - 1); 2761 for (i = 0; i < brd->info->nports; i++) 2762 tty_port_destroy(&brd->ports[i].port); 2763 free_irq(brd->irq, brd); 2764 mxser_release_ISA_res(brd); 2765 brd->info = NULL; 2766 break; 2767 } 2768 } 2769 if (brd->info == NULL) 2770 continue; 2771 2772 m++; 2773 } 2774 2775 retval = pci_register_driver(&mxser_driver); 2776 if (retval) { 2777 printk(KERN_ERR "mxser: can't register pci driver\n"); 2778 if (!m) { 2779 retval = -ENODEV; 2780 goto err_unr; 2781 } /* else: we have some ISA cards under control */ 2782 } 2783 2784 return 0; 2785 err_unr: 2786 tty_unregister_driver(mxvar_sdriver); 2787 err_put: 2788 put_tty_driver(mxvar_sdriver); 2789 return retval; 2790 } 2791 2792 static void __exit mxser_module_exit(void) 2793 { 2794 unsigned int i; 2795 2796 pci_unregister_driver(&mxser_driver); 2797 2798 for (i = 0; i < MXSER_BOARDS; i++) /* ISA remains */ 2799 if (mxser_boards[i].info != NULL) 2800 mxser_board_remove(&mxser_boards[i]); 2801 tty_unregister_driver(mxvar_sdriver); 2802 put_tty_driver(mxvar_sdriver); 2803 2804 for (i = 0; i < MXSER_BOARDS; i++) 2805 if (mxser_boards[i].info != NULL) 2806 mxser_release_ISA_res(&mxser_boards[i]); 2807 } 2808 2809 module_init(mxser_module_init); 2810 module_exit(mxser_module_exit); 2811