1 // SPDX-License-Identifier: GPL-2.0 2 /* 3 * Serial driver for the amiga builtin port. 4 * 5 * This code was created by taking serial.c version 4.30 from kernel 6 * release 2.3.22, replacing all hardware related stuff with the 7 * corresponding amiga hardware actions, and removing all irrelevant 8 * code. As a consequence, it uses many of the constants and names 9 * associated with the registers and bits of 16550 compatible UARTS - 10 * but only to keep track of status, etc in the state variables. It 11 * was done this was to make it easier to keep the code in line with 12 * (non hardware specific) changes to serial.c. 13 * 14 * The port is registered with the tty driver as minor device 64, and 15 * therefore other ports should should only use 65 upwards. 16 * 17 * Richard Lucock 28/12/99 18 * 19 * Copyright (C) 1991, 1992 Linus Torvalds 20 * Copyright (C) 1992, 1993, 1994, 1995, 1996, 1997, 21 * 1998, 1999 Theodore Ts'o 22 * 23 */ 24 25 /* 26 * Serial driver configuration section. Here are the various options: 27 * 28 * SERIAL_PARANOIA_CHECK 29 * Check the magic number for the async_structure where 30 * ever possible. 31 */ 32 33 #include <linux/delay.h> 34 35 #undef SERIAL_PARANOIA_CHECK 36 37 /* Set of debugging defines */ 38 39 #undef SERIAL_DEBUG_INTR 40 #undef SERIAL_DEBUG_OPEN 41 #undef SERIAL_DEBUG_FLOW 42 #undef SERIAL_DEBUG_RS_WAIT_UNTIL_SENT 43 44 /* Sanity checks */ 45 46 #if defined(MODULE) && defined(SERIAL_DEBUG_MCOUNT) 47 #define DBG_CNT(s) printk("(%s): [%x] refc=%d, serc=%d, ttyc=%d -> %s\n", \ 48 tty->name, (info->tport.flags), serial_driver->refcount,info->count,tty->count,s) 49 #else 50 #define DBG_CNT(s) 51 #endif 52 53 /* 54 * End of serial driver configuration section. 55 */ 56 57 #include <linux/module.h> 58 59 #include <linux/types.h> 60 #include <linux/serial.h> 61 #include <linux/serial_reg.h> 62 static char *serial_version = "4.30"; 63 64 #include <linux/errno.h> 65 #include <linux/signal.h> 66 #include <linux/sched.h> 67 #include <linux/kernel.h> 68 #include <linux/timer.h> 69 #include <linux/interrupt.h> 70 #include <linux/tty.h> 71 #include <linux/tty_flip.h> 72 #include <linux/circ_buf.h> 73 #include <linux/console.h> 74 #include <linux/major.h> 75 #include <linux/string.h> 76 #include <linux/fcntl.h> 77 #include <linux/ptrace.h> 78 #include <linux/ioport.h> 79 #include <linux/mm.h> 80 #include <linux/seq_file.h> 81 #include <linux/slab.h> 82 #include <linux/init.h> 83 #include <linux/bitops.h> 84 #include <linux/platform_device.h> 85 86 #include <asm/setup.h> 87 88 89 #include <asm/irq.h> 90 91 #include <asm/amigahw.h> 92 #include <asm/amigaints.h> 93 94 struct serial_state { 95 struct tty_port tport; 96 struct circ_buf xmit; 97 struct async_icount icount; 98 99 unsigned long port; 100 int baud_base; 101 int xmit_fifo_size; 102 int custom_divisor; 103 int read_status_mask; 104 int ignore_status_mask; 105 int timeout; 106 int quot; 107 int IER; /* Interrupt Enable Register */ 108 int MCR; /* Modem control register */ 109 int x_char; /* xon/xoff character */ 110 }; 111 112 #define custom amiga_custom 113 static char *serial_name = "Amiga-builtin serial driver"; 114 115 static struct tty_driver *serial_driver; 116 117 /* number of characters left in xmit buffer before we ask for more */ 118 #define WAKEUP_CHARS 256 119 120 static unsigned char current_ctl_bits; 121 122 static void change_speed(struct tty_struct *tty, struct serial_state *info, 123 struct ktermios *old); 124 static void rs_wait_until_sent(struct tty_struct *tty, int timeout); 125 126 127 static struct serial_state rs_table[1]; 128 129 #define NR_PORTS ARRAY_SIZE(rs_table) 130 131 #include <linux/uaccess.h> 132 133 #define serial_isroot() (capable(CAP_SYS_ADMIN)) 134 135 136 static inline int serial_paranoia_check(struct serial_state *info, 137 char *name, const char *routine) 138 { 139 #ifdef SERIAL_PARANOIA_CHECK 140 static const char *badmagic = 141 "Warning: bad magic number for serial struct (%s) in %s\n"; 142 static const char *badinfo = 143 "Warning: null async_struct for (%s) in %s\n"; 144 145 if (!info) { 146 printk(badinfo, name, routine); 147 return 1; 148 } 149 if (info->magic != SERIAL_MAGIC) { 150 printk(badmagic, name, routine); 151 return 1; 152 } 153 #endif 154 return 0; 155 } 156 157 /* some serial hardware definitions */ 158 #define SDR_OVRUN (1<<15) 159 #define SDR_RBF (1<<14) 160 #define SDR_TBE (1<<13) 161 #define SDR_TSRE (1<<12) 162 163 #define SERPER_PARENB (1<<15) 164 165 #define AC_SETCLR (1<<15) 166 #define AC_UARTBRK (1<<11) 167 168 #define SER_DTR (1<<7) 169 #define SER_RTS (1<<6) 170 #define SER_DCD (1<<5) 171 #define SER_CTS (1<<4) 172 #define SER_DSR (1<<3) 173 174 static __inline__ void rtsdtr_ctrl(int bits) 175 { 176 ciab.pra = ((bits & (SER_RTS | SER_DTR)) ^ (SER_RTS | SER_DTR)) | (ciab.pra & ~(SER_RTS | SER_DTR)); 177 } 178 179 /* 180 * ------------------------------------------------------------ 181 * rs_stop() and rs_start() 182 * 183 * This routines are called before setting or resetting tty->stopped. 184 * They enable or disable transmitter interrupts, as necessary. 185 * ------------------------------------------------------------ 186 */ 187 static void rs_stop(struct tty_struct *tty) 188 { 189 struct serial_state *info = tty->driver_data; 190 unsigned long flags; 191 192 if (serial_paranoia_check(info, tty->name, "rs_stop")) 193 return; 194 195 local_irq_save(flags); 196 if (info->IER & UART_IER_THRI) { 197 info->IER &= ~UART_IER_THRI; 198 /* disable Tx interrupt and remove any pending interrupts */ 199 custom.intena = IF_TBE; 200 mb(); 201 custom.intreq = IF_TBE; 202 mb(); 203 } 204 local_irq_restore(flags); 205 } 206 207 static void rs_start(struct tty_struct *tty) 208 { 209 struct serial_state *info = tty->driver_data; 210 unsigned long flags; 211 212 if (serial_paranoia_check(info, tty->name, "rs_start")) 213 return; 214 215 local_irq_save(flags); 216 if (info->xmit.head != info->xmit.tail 217 && info->xmit.buf 218 && !(info->IER & UART_IER_THRI)) { 219 info->IER |= UART_IER_THRI; 220 custom.intena = IF_SETCLR | IF_TBE; 221 mb(); 222 /* set a pending Tx Interrupt, transmitter should restart now */ 223 custom.intreq = IF_SETCLR | IF_TBE; 224 mb(); 225 } 226 local_irq_restore(flags); 227 } 228 229 /* 230 * ---------------------------------------------------------------------- 231 * 232 * Here starts the interrupt handling routines. All of the following 233 * subroutines are declared as inline and are folded into 234 * rs_interrupt(). They were separated out for readability's sake. 235 * 236 * Note: rs_interrupt() is a "fast" interrupt, which means that it 237 * runs with interrupts turned off. People who may want to modify 238 * rs_interrupt() should try to keep the interrupt handler as fast as 239 * possible. After you are done making modifications, it is not a bad 240 * idea to do: 241 * 242 * gcc -S -DKERNEL -Wall -Wstrict-prototypes -O6 -fomit-frame-pointer serial.c 243 * 244 * and look at the resulting assemble code in serial.s. 245 * 246 * - Ted Ts'o (tytso@mit.edu), 7-Mar-93 247 * ----------------------------------------------------------------------- 248 */ 249 250 static void receive_chars(struct serial_state *info) 251 { 252 int status; 253 int serdatr; 254 unsigned char ch, flag; 255 struct async_icount *icount; 256 int oe = 0; 257 258 icount = &info->icount; 259 260 status = UART_LSR_DR; /* We obviously have a character! */ 261 serdatr = custom.serdatr; 262 mb(); 263 custom.intreq = IF_RBF; 264 mb(); 265 266 if((serdatr & 0x1ff) == 0) 267 status |= UART_LSR_BI; 268 if(serdatr & SDR_OVRUN) 269 status |= UART_LSR_OE; 270 271 ch = serdatr & 0xff; 272 icount->rx++; 273 274 #ifdef SERIAL_DEBUG_INTR 275 printk("DR%02x:%02x...", ch, status); 276 #endif 277 flag = TTY_NORMAL; 278 279 /* 280 * We don't handle parity or frame errors - but I have left 281 * the code in, since I'm not sure that the errors can't be 282 * detected. 283 */ 284 285 if (status & (UART_LSR_BI | UART_LSR_PE | 286 UART_LSR_FE | UART_LSR_OE)) { 287 /* 288 * For statistics only 289 */ 290 if (status & UART_LSR_BI) { 291 status &= ~(UART_LSR_FE | UART_LSR_PE); 292 icount->brk++; 293 } else if (status & UART_LSR_PE) 294 icount->parity++; 295 else if (status & UART_LSR_FE) 296 icount->frame++; 297 if (status & UART_LSR_OE) 298 icount->overrun++; 299 300 /* 301 * Now check to see if character should be 302 * ignored, and mask off conditions which 303 * should be ignored. 304 */ 305 if (status & info->ignore_status_mask) 306 goto out; 307 308 status &= info->read_status_mask; 309 310 if (status & (UART_LSR_BI)) { 311 #ifdef SERIAL_DEBUG_INTR 312 printk("handling break...."); 313 #endif 314 flag = TTY_BREAK; 315 if (info->tport.flags & ASYNC_SAK) 316 do_SAK(info->tport.tty); 317 } else if (status & UART_LSR_PE) 318 flag = TTY_PARITY; 319 else if (status & UART_LSR_FE) 320 flag = TTY_FRAME; 321 if (status & UART_LSR_OE) { 322 /* 323 * Overrun is special, since it's 324 * reported immediately, and doesn't 325 * affect the current character 326 */ 327 oe = 1; 328 } 329 } 330 tty_insert_flip_char(&info->tport, ch, flag); 331 if (oe == 1) 332 tty_insert_flip_char(&info->tport, 0, TTY_OVERRUN); 333 tty_flip_buffer_push(&info->tport); 334 out: 335 return; 336 } 337 338 static void transmit_chars(struct serial_state *info) 339 { 340 custom.intreq = IF_TBE; 341 mb(); 342 if (info->x_char) { 343 custom.serdat = info->x_char | 0x100; 344 mb(); 345 info->icount.tx++; 346 info->x_char = 0; 347 return; 348 } 349 if (info->xmit.head == info->xmit.tail 350 || info->tport.tty->stopped 351 || info->tport.tty->hw_stopped) { 352 info->IER &= ~UART_IER_THRI; 353 custom.intena = IF_TBE; 354 mb(); 355 return; 356 } 357 358 custom.serdat = info->xmit.buf[info->xmit.tail++] | 0x100; 359 mb(); 360 info->xmit.tail = info->xmit.tail & (SERIAL_XMIT_SIZE-1); 361 info->icount.tx++; 362 363 if (CIRC_CNT(info->xmit.head, 364 info->xmit.tail, 365 SERIAL_XMIT_SIZE) < WAKEUP_CHARS) 366 tty_wakeup(info->tport.tty); 367 368 #ifdef SERIAL_DEBUG_INTR 369 printk("THRE..."); 370 #endif 371 if (info->xmit.head == info->xmit.tail) { 372 custom.intena = IF_TBE; 373 mb(); 374 info->IER &= ~UART_IER_THRI; 375 } 376 } 377 378 static void check_modem_status(struct serial_state *info) 379 { 380 struct tty_port *port = &info->tport; 381 unsigned char status = ciab.pra & (SER_DCD | SER_CTS | SER_DSR); 382 unsigned char dstatus; 383 struct async_icount *icount; 384 385 /* Determine bits that have changed */ 386 dstatus = status ^ current_ctl_bits; 387 current_ctl_bits = status; 388 389 if (dstatus) { 390 icount = &info->icount; 391 /* update input line counters */ 392 if (dstatus & SER_DSR) 393 icount->dsr++; 394 if (dstatus & SER_DCD) { 395 icount->dcd++; 396 } 397 if (dstatus & SER_CTS) 398 icount->cts++; 399 wake_up_interruptible(&port->delta_msr_wait); 400 } 401 402 if (tty_port_check_carrier(port) && (dstatus & SER_DCD)) { 403 #if (defined(SERIAL_DEBUG_OPEN) || defined(SERIAL_DEBUG_INTR)) 404 printk("ttyS%d CD now %s...", info->line, 405 (!(status & SER_DCD)) ? "on" : "off"); 406 #endif 407 if (!(status & SER_DCD)) 408 wake_up_interruptible(&port->open_wait); 409 else { 410 #ifdef SERIAL_DEBUG_OPEN 411 printk("doing serial hangup..."); 412 #endif 413 if (port->tty) 414 tty_hangup(port->tty); 415 } 416 } 417 if (tty_port_cts_enabled(port)) { 418 if (port->tty->hw_stopped) { 419 if (!(status & SER_CTS)) { 420 #if (defined(SERIAL_DEBUG_INTR) || defined(SERIAL_DEBUG_FLOW)) 421 printk("CTS tx start..."); 422 #endif 423 port->tty->hw_stopped = 0; 424 info->IER |= UART_IER_THRI; 425 custom.intena = IF_SETCLR | IF_TBE; 426 mb(); 427 /* set a pending Tx Interrupt, transmitter should restart now */ 428 custom.intreq = IF_SETCLR | IF_TBE; 429 mb(); 430 tty_wakeup(port->tty); 431 return; 432 } 433 } else { 434 if ((status & SER_CTS)) { 435 #if (defined(SERIAL_DEBUG_INTR) || defined(SERIAL_DEBUG_FLOW)) 436 printk("CTS tx stop..."); 437 #endif 438 port->tty->hw_stopped = 1; 439 info->IER &= ~UART_IER_THRI; 440 /* disable Tx interrupt and remove any pending interrupts */ 441 custom.intena = IF_TBE; 442 mb(); 443 custom.intreq = IF_TBE; 444 mb(); 445 } 446 } 447 } 448 } 449 450 static irqreturn_t ser_vbl_int( int irq, void *data) 451 { 452 /* vbl is just a periodic interrupt we tie into to update modem status */ 453 struct serial_state *info = data; 454 /* 455 * TBD - is it better to unregister from this interrupt or to 456 * ignore it if MSI is clear ? 457 */ 458 if(info->IER & UART_IER_MSI) 459 check_modem_status(info); 460 return IRQ_HANDLED; 461 } 462 463 static irqreturn_t ser_rx_int(int irq, void *dev_id) 464 { 465 struct serial_state *info = dev_id; 466 467 #ifdef SERIAL_DEBUG_INTR 468 printk("ser_rx_int..."); 469 #endif 470 471 if (!info->tport.tty) 472 return IRQ_NONE; 473 474 receive_chars(info); 475 #ifdef SERIAL_DEBUG_INTR 476 printk("end.\n"); 477 #endif 478 return IRQ_HANDLED; 479 } 480 481 static irqreturn_t ser_tx_int(int irq, void *dev_id) 482 { 483 struct serial_state *info = dev_id; 484 485 if (custom.serdatr & SDR_TBE) { 486 #ifdef SERIAL_DEBUG_INTR 487 printk("ser_tx_int..."); 488 #endif 489 490 if (!info->tport.tty) 491 return IRQ_NONE; 492 493 transmit_chars(info); 494 #ifdef SERIAL_DEBUG_INTR 495 printk("end.\n"); 496 #endif 497 } 498 return IRQ_HANDLED; 499 } 500 501 /* 502 * ------------------------------------------------------------------- 503 * Here ends the serial interrupt routines. 504 * ------------------------------------------------------------------- 505 */ 506 507 /* 508 * --------------------------------------------------------------- 509 * Low level utility subroutines for the serial driver: routines to 510 * figure out the appropriate timeout for an interrupt chain, routines 511 * to initialize and startup a serial port, and routines to shutdown a 512 * serial port. Useful stuff like that. 513 * --------------------------------------------------------------- 514 */ 515 516 static int startup(struct tty_struct *tty, struct serial_state *info) 517 { 518 struct tty_port *port = &info->tport; 519 unsigned long flags; 520 int retval=0; 521 unsigned long page; 522 523 page = get_zeroed_page(GFP_KERNEL); 524 if (!page) 525 return -ENOMEM; 526 527 local_irq_save(flags); 528 529 if (tty_port_initialized(port)) { 530 free_page(page); 531 goto errout; 532 } 533 534 if (info->xmit.buf) 535 free_page(page); 536 else 537 info->xmit.buf = (unsigned char *) page; 538 539 #ifdef SERIAL_DEBUG_OPEN 540 printk("starting up ttys%d ...", info->line); 541 #endif 542 543 /* Clear anything in the input buffer */ 544 545 custom.intreq = IF_RBF; 546 mb(); 547 548 retval = request_irq(IRQ_AMIGA_VERTB, ser_vbl_int, 0, "serial status", info); 549 if (retval) { 550 if (serial_isroot()) { 551 set_bit(TTY_IO_ERROR, &tty->flags); 552 retval = 0; 553 } 554 goto errout; 555 } 556 557 /* enable both Rx and Tx interrupts */ 558 custom.intena = IF_SETCLR | IF_RBF | IF_TBE; 559 mb(); 560 info->IER = UART_IER_MSI; 561 562 /* remember current state of the DCD and CTS bits */ 563 current_ctl_bits = ciab.pra & (SER_DCD | SER_CTS | SER_DSR); 564 565 info->MCR = 0; 566 if (C_BAUD(tty)) 567 info->MCR = SER_DTR | SER_RTS; 568 rtsdtr_ctrl(info->MCR); 569 570 clear_bit(TTY_IO_ERROR, &tty->flags); 571 info->xmit.head = info->xmit.tail = 0; 572 573 /* 574 * and set the speed of the serial port 575 */ 576 change_speed(tty, info, NULL); 577 578 tty_port_set_initialized(port, 1); 579 local_irq_restore(flags); 580 return 0; 581 582 errout: 583 local_irq_restore(flags); 584 return retval; 585 } 586 587 /* 588 * This routine will shutdown a serial port; interrupts are disabled, and 589 * DTR is dropped if the hangup on close termio flag is on. 590 */ 591 static void shutdown(struct tty_struct *tty, struct serial_state *info) 592 { 593 unsigned long flags; 594 struct serial_state *state; 595 596 if (!tty_port_initialized(&info->tport)) 597 return; 598 599 state = info; 600 601 #ifdef SERIAL_DEBUG_OPEN 602 printk("Shutting down serial port %d ....\n", info->line); 603 #endif 604 605 local_irq_save(flags); /* Disable interrupts */ 606 607 /* 608 * clear delta_msr_wait queue to avoid mem leaks: we may free the irq 609 * here so the queue might never be waken up 610 */ 611 wake_up_interruptible(&info->tport.delta_msr_wait); 612 613 /* 614 * Free the IRQ, if necessary 615 */ 616 free_irq(IRQ_AMIGA_VERTB, info); 617 618 if (info->xmit.buf) { 619 free_page((unsigned long) info->xmit.buf); 620 info->xmit.buf = NULL; 621 } 622 623 info->IER = 0; 624 custom.intena = IF_RBF | IF_TBE; 625 mb(); 626 627 /* disable break condition */ 628 custom.adkcon = AC_UARTBRK; 629 mb(); 630 631 if (C_HUPCL(tty)) 632 info->MCR &= ~(SER_DTR|SER_RTS); 633 rtsdtr_ctrl(info->MCR); 634 635 set_bit(TTY_IO_ERROR, &tty->flags); 636 637 tty_port_set_initialized(&info->tport, 0); 638 local_irq_restore(flags); 639 } 640 641 642 /* 643 * This routine is called to set the UART divisor registers to match 644 * the specified baud rate for a serial port. 645 */ 646 static void change_speed(struct tty_struct *tty, struct serial_state *info, 647 struct ktermios *old_termios) 648 { 649 struct tty_port *port = &info->tport; 650 int quot = 0, baud_base, baud; 651 unsigned cflag, cval = 0; 652 int bits; 653 unsigned long flags; 654 655 cflag = tty->termios.c_cflag; 656 657 /* Byte size is always 8 bits plus parity bit if requested */ 658 659 cval = 3; bits = 10; 660 if (cflag & CSTOPB) { 661 cval |= 0x04; 662 bits++; 663 } 664 if (cflag & PARENB) { 665 cval |= UART_LCR_PARITY; 666 bits++; 667 } 668 if (!(cflag & PARODD)) 669 cval |= UART_LCR_EPAR; 670 #ifdef CMSPAR 671 if (cflag & CMSPAR) 672 cval |= UART_LCR_SPAR; 673 #endif 674 675 /* Determine divisor based on baud rate */ 676 baud = tty_get_baud_rate(tty); 677 if (!baud) 678 baud = 9600; /* B0 transition handled in rs_set_termios */ 679 baud_base = info->baud_base; 680 if (baud == 38400 && (port->flags & ASYNC_SPD_MASK) == ASYNC_SPD_CUST) 681 quot = info->custom_divisor; 682 else { 683 if (baud == 134) 684 /* Special case since 134 is really 134.5 */ 685 quot = (2*baud_base / 269); 686 else if (baud) 687 quot = baud_base / baud; 688 } 689 /* If the quotient is zero refuse the change */ 690 if (!quot && old_termios) { 691 /* FIXME: Will need updating for new tty in the end */ 692 tty->termios.c_cflag &= ~CBAUD; 693 tty->termios.c_cflag |= (old_termios->c_cflag & CBAUD); 694 baud = tty_get_baud_rate(tty); 695 if (!baud) 696 baud = 9600; 697 if (baud == 38400 && 698 (port->flags & ASYNC_SPD_MASK) == ASYNC_SPD_CUST) 699 quot = info->custom_divisor; 700 else { 701 if (baud == 134) 702 /* Special case since 134 is really 134.5 */ 703 quot = (2*baud_base / 269); 704 else if (baud) 705 quot = baud_base / baud; 706 } 707 } 708 /* As a last resort, if the quotient is zero, default to 9600 bps */ 709 if (!quot) 710 quot = baud_base / 9600; 711 info->quot = quot; 712 info->timeout = ((info->xmit_fifo_size*HZ*bits*quot) / baud_base); 713 info->timeout += HZ/50; /* Add .02 seconds of slop */ 714 715 /* CTS flow control flag and modem status interrupts */ 716 info->IER &= ~UART_IER_MSI; 717 if (port->flags & ASYNC_HARDPPS_CD) 718 info->IER |= UART_IER_MSI; 719 tty_port_set_cts_flow(port, cflag & CRTSCTS); 720 if (cflag & CRTSCTS) 721 info->IER |= UART_IER_MSI; 722 tty_port_set_check_carrier(port, ~cflag & CLOCAL); 723 if (~cflag & CLOCAL) 724 info->IER |= UART_IER_MSI; 725 /* TBD: 726 * Does clearing IER_MSI imply that we should disable the VBL interrupt ? 727 */ 728 729 /* 730 * Set up parity check flag 731 */ 732 733 info->read_status_mask = UART_LSR_OE | UART_LSR_DR; 734 if (I_INPCK(tty)) 735 info->read_status_mask |= UART_LSR_FE | UART_LSR_PE; 736 if (I_BRKINT(tty) || I_PARMRK(tty)) 737 info->read_status_mask |= UART_LSR_BI; 738 739 /* 740 * Characters to ignore 741 */ 742 info->ignore_status_mask = 0; 743 if (I_IGNPAR(tty)) 744 info->ignore_status_mask |= UART_LSR_PE | UART_LSR_FE; 745 if (I_IGNBRK(tty)) { 746 info->ignore_status_mask |= UART_LSR_BI; 747 /* 748 * If we're ignore parity and break indicators, ignore 749 * overruns too. (For real raw support). 750 */ 751 if (I_IGNPAR(tty)) 752 info->ignore_status_mask |= UART_LSR_OE; 753 } 754 /* 755 * !!! ignore all characters if CREAD is not set 756 */ 757 if ((cflag & CREAD) == 0) 758 info->ignore_status_mask |= UART_LSR_DR; 759 local_irq_save(flags); 760 761 { 762 short serper; 763 764 /* Set up the baud rate */ 765 serper = quot - 1; 766 767 /* Enable or disable parity bit */ 768 769 if(cval & UART_LCR_PARITY) 770 serper |= (SERPER_PARENB); 771 772 custom.serper = serper; 773 mb(); 774 } 775 776 local_irq_restore(flags); 777 } 778 779 static int rs_put_char(struct tty_struct *tty, unsigned char ch) 780 { 781 struct serial_state *info; 782 unsigned long flags; 783 784 info = tty->driver_data; 785 786 if (serial_paranoia_check(info, tty->name, "rs_put_char")) 787 return 0; 788 789 if (!info->xmit.buf) 790 return 0; 791 792 local_irq_save(flags); 793 if (CIRC_SPACE(info->xmit.head, 794 info->xmit.tail, 795 SERIAL_XMIT_SIZE) == 0) { 796 local_irq_restore(flags); 797 return 0; 798 } 799 800 info->xmit.buf[info->xmit.head++] = ch; 801 info->xmit.head &= SERIAL_XMIT_SIZE-1; 802 local_irq_restore(flags); 803 return 1; 804 } 805 806 static void rs_flush_chars(struct tty_struct *tty) 807 { 808 struct serial_state *info = tty->driver_data; 809 unsigned long flags; 810 811 if (serial_paranoia_check(info, tty->name, "rs_flush_chars")) 812 return; 813 814 if (info->xmit.head == info->xmit.tail 815 || tty->stopped 816 || tty->hw_stopped 817 || !info->xmit.buf) 818 return; 819 820 local_irq_save(flags); 821 info->IER |= UART_IER_THRI; 822 custom.intena = IF_SETCLR | IF_TBE; 823 mb(); 824 /* set a pending Tx Interrupt, transmitter should restart now */ 825 custom.intreq = IF_SETCLR | IF_TBE; 826 mb(); 827 local_irq_restore(flags); 828 } 829 830 static int rs_write(struct tty_struct * tty, const unsigned char *buf, int count) 831 { 832 int c, ret = 0; 833 struct serial_state *info = tty->driver_data; 834 unsigned long flags; 835 836 if (serial_paranoia_check(info, tty->name, "rs_write")) 837 return 0; 838 839 if (!info->xmit.buf) 840 return 0; 841 842 local_irq_save(flags); 843 while (1) { 844 c = CIRC_SPACE_TO_END(info->xmit.head, 845 info->xmit.tail, 846 SERIAL_XMIT_SIZE); 847 if (count < c) 848 c = count; 849 if (c <= 0) { 850 break; 851 } 852 memcpy(info->xmit.buf + info->xmit.head, buf, c); 853 info->xmit.head = ((info->xmit.head + c) & 854 (SERIAL_XMIT_SIZE-1)); 855 buf += c; 856 count -= c; 857 ret += c; 858 } 859 local_irq_restore(flags); 860 861 if (info->xmit.head != info->xmit.tail 862 && !tty->stopped 863 && !tty->hw_stopped 864 && !(info->IER & UART_IER_THRI)) { 865 info->IER |= UART_IER_THRI; 866 local_irq_disable(); 867 custom.intena = IF_SETCLR | IF_TBE; 868 mb(); 869 /* set a pending Tx Interrupt, transmitter should restart now */ 870 custom.intreq = IF_SETCLR | IF_TBE; 871 mb(); 872 local_irq_restore(flags); 873 } 874 return ret; 875 } 876 877 static int rs_write_room(struct tty_struct *tty) 878 { 879 struct serial_state *info = tty->driver_data; 880 881 if (serial_paranoia_check(info, tty->name, "rs_write_room")) 882 return 0; 883 return CIRC_SPACE(info->xmit.head, info->xmit.tail, SERIAL_XMIT_SIZE); 884 } 885 886 static int rs_chars_in_buffer(struct tty_struct *tty) 887 { 888 struct serial_state *info = tty->driver_data; 889 890 if (serial_paranoia_check(info, tty->name, "rs_chars_in_buffer")) 891 return 0; 892 return CIRC_CNT(info->xmit.head, info->xmit.tail, SERIAL_XMIT_SIZE); 893 } 894 895 static void rs_flush_buffer(struct tty_struct *tty) 896 { 897 struct serial_state *info = tty->driver_data; 898 unsigned long flags; 899 900 if (serial_paranoia_check(info, tty->name, "rs_flush_buffer")) 901 return; 902 local_irq_save(flags); 903 info->xmit.head = info->xmit.tail = 0; 904 local_irq_restore(flags); 905 tty_wakeup(tty); 906 } 907 908 /* 909 * This function is used to send a high-priority XON/XOFF character to 910 * the device 911 */ 912 static void rs_send_xchar(struct tty_struct *tty, char ch) 913 { 914 struct serial_state *info = tty->driver_data; 915 unsigned long flags; 916 917 if (serial_paranoia_check(info, tty->name, "rs_send_xchar")) 918 return; 919 920 info->x_char = ch; 921 if (ch) { 922 /* Make sure transmit interrupts are on */ 923 924 /* Check this ! */ 925 local_irq_save(flags); 926 if(!(custom.intenar & IF_TBE)) { 927 custom.intena = IF_SETCLR | IF_TBE; 928 mb(); 929 /* set a pending Tx Interrupt, transmitter should restart now */ 930 custom.intreq = IF_SETCLR | IF_TBE; 931 mb(); 932 } 933 local_irq_restore(flags); 934 935 info->IER |= UART_IER_THRI; 936 } 937 } 938 939 /* 940 * ------------------------------------------------------------ 941 * rs_throttle() 942 * 943 * This routine is called by the upper-layer tty layer to signal that 944 * incoming characters should be throttled. 945 * ------------------------------------------------------------ 946 */ 947 static void rs_throttle(struct tty_struct * tty) 948 { 949 struct serial_state *info = tty->driver_data; 950 unsigned long flags; 951 #ifdef SERIAL_DEBUG_THROTTLE 952 printk("throttle %s ....\n", tty_name(tty)); 953 #endif 954 955 if (serial_paranoia_check(info, tty->name, "rs_throttle")) 956 return; 957 958 if (I_IXOFF(tty)) 959 rs_send_xchar(tty, STOP_CHAR(tty)); 960 961 if (C_CRTSCTS(tty)) 962 info->MCR &= ~SER_RTS; 963 964 local_irq_save(flags); 965 rtsdtr_ctrl(info->MCR); 966 local_irq_restore(flags); 967 } 968 969 static void rs_unthrottle(struct tty_struct * tty) 970 { 971 struct serial_state *info = tty->driver_data; 972 unsigned long flags; 973 #ifdef SERIAL_DEBUG_THROTTLE 974 printk("unthrottle %s ....\n", tty_name(tty)); 975 #endif 976 977 if (serial_paranoia_check(info, tty->name, "rs_unthrottle")) 978 return; 979 980 if (I_IXOFF(tty)) { 981 if (info->x_char) 982 info->x_char = 0; 983 else 984 rs_send_xchar(tty, START_CHAR(tty)); 985 } 986 if (C_CRTSCTS(tty)) 987 info->MCR |= SER_RTS; 988 local_irq_save(flags); 989 rtsdtr_ctrl(info->MCR); 990 local_irq_restore(flags); 991 } 992 993 /* 994 * ------------------------------------------------------------ 995 * rs_ioctl() and friends 996 * ------------------------------------------------------------ 997 */ 998 999 static int get_serial_info(struct tty_struct *tty, struct serial_state *state, 1000 struct serial_struct __user * retinfo) 1001 { 1002 struct serial_struct tmp; 1003 1004 memset(&tmp, 0, sizeof(tmp)); 1005 tty_lock(tty); 1006 tmp.line = tty->index; 1007 tmp.port = state->port; 1008 tmp.flags = state->tport.flags; 1009 tmp.xmit_fifo_size = state->xmit_fifo_size; 1010 tmp.baud_base = state->baud_base; 1011 tmp.close_delay = state->tport.close_delay; 1012 tmp.closing_wait = state->tport.closing_wait; 1013 tmp.custom_divisor = state->custom_divisor; 1014 tty_unlock(tty); 1015 if (copy_to_user(retinfo,&tmp,sizeof(*retinfo))) 1016 return -EFAULT; 1017 return 0; 1018 } 1019 1020 static int set_serial_info(struct tty_struct *tty, struct serial_state *state, 1021 struct serial_struct __user * new_info) 1022 { 1023 struct tty_port *port = &state->tport; 1024 struct serial_struct new_serial; 1025 bool change_spd; 1026 int retval = 0; 1027 1028 if (copy_from_user(&new_serial,new_info,sizeof(new_serial))) 1029 return -EFAULT; 1030 1031 tty_lock(tty); 1032 change_spd = ((new_serial.flags ^ port->flags) & ASYNC_SPD_MASK) || 1033 new_serial.custom_divisor != state->custom_divisor; 1034 if (new_serial.irq || new_serial.port != state->port || 1035 new_serial.xmit_fifo_size != state->xmit_fifo_size) { 1036 tty_unlock(tty); 1037 return -EINVAL; 1038 } 1039 1040 if (!serial_isroot()) { 1041 if ((new_serial.baud_base != state->baud_base) || 1042 (new_serial.close_delay != port->close_delay) || 1043 (new_serial.xmit_fifo_size != state->xmit_fifo_size) || 1044 ((new_serial.flags & ~ASYNC_USR_MASK) != 1045 (port->flags & ~ASYNC_USR_MASK))) { 1046 tty_unlock(tty); 1047 return -EPERM; 1048 } 1049 port->flags = ((port->flags & ~ASYNC_USR_MASK) | 1050 (new_serial.flags & ASYNC_USR_MASK)); 1051 state->custom_divisor = new_serial.custom_divisor; 1052 goto check_and_exit; 1053 } 1054 1055 if (new_serial.baud_base < 9600) { 1056 tty_unlock(tty); 1057 return -EINVAL; 1058 } 1059 1060 /* 1061 * OK, past this point, all the error checking has been done. 1062 * At this point, we start making changes..... 1063 */ 1064 1065 state->baud_base = new_serial.baud_base; 1066 port->flags = ((port->flags & ~ASYNC_FLAGS) | 1067 (new_serial.flags & ASYNC_FLAGS)); 1068 state->custom_divisor = new_serial.custom_divisor; 1069 port->close_delay = new_serial.close_delay * HZ/100; 1070 port->closing_wait = new_serial.closing_wait * HZ/100; 1071 port->low_latency = (port->flags & ASYNC_LOW_LATENCY) ? 1 : 0; 1072 1073 check_and_exit: 1074 if (tty_port_initialized(port)) { 1075 if (change_spd) { 1076 /* warn about deprecation unless clearing */ 1077 if (new_serial.flags & ASYNC_SPD_MASK) 1078 dev_warn_ratelimited(tty->dev, "use of SPD flags is deprecated\n"); 1079 change_speed(tty, state, NULL); 1080 } 1081 } else 1082 retval = startup(tty, state); 1083 tty_unlock(tty); 1084 return retval; 1085 } 1086 1087 1088 /* 1089 * get_lsr_info - get line status register info 1090 * 1091 * Purpose: Let user call ioctl() to get info when the UART physically 1092 * is emptied. On bus types like RS485, the transmitter must 1093 * release the bus after transmitting. This must be done when 1094 * the transmit shift register is empty, not be done when the 1095 * transmit holding register is empty. This functionality 1096 * allows an RS485 driver to be written in user space. 1097 */ 1098 static int get_lsr_info(struct serial_state *info, unsigned int __user *value) 1099 { 1100 unsigned char status; 1101 unsigned int result; 1102 unsigned long flags; 1103 1104 local_irq_save(flags); 1105 status = custom.serdatr; 1106 mb(); 1107 local_irq_restore(flags); 1108 result = ((status & SDR_TSRE) ? TIOCSER_TEMT : 0); 1109 if (copy_to_user(value, &result, sizeof(int))) 1110 return -EFAULT; 1111 return 0; 1112 } 1113 1114 1115 static int rs_tiocmget(struct tty_struct *tty) 1116 { 1117 struct serial_state *info = tty->driver_data; 1118 unsigned char control, status; 1119 unsigned long flags; 1120 1121 if (serial_paranoia_check(info, tty->name, "rs_ioctl")) 1122 return -ENODEV; 1123 if (tty_io_error(tty)) 1124 return -EIO; 1125 1126 control = info->MCR; 1127 local_irq_save(flags); 1128 status = ciab.pra; 1129 local_irq_restore(flags); 1130 return ((control & SER_RTS) ? TIOCM_RTS : 0) 1131 | ((control & SER_DTR) ? TIOCM_DTR : 0) 1132 | (!(status & SER_DCD) ? TIOCM_CAR : 0) 1133 | (!(status & SER_DSR) ? TIOCM_DSR : 0) 1134 | (!(status & SER_CTS) ? TIOCM_CTS : 0); 1135 } 1136 1137 static int rs_tiocmset(struct tty_struct *tty, unsigned int set, 1138 unsigned int clear) 1139 { 1140 struct serial_state *info = tty->driver_data; 1141 unsigned long flags; 1142 1143 if (serial_paranoia_check(info, tty->name, "rs_ioctl")) 1144 return -ENODEV; 1145 if (tty_io_error(tty)) 1146 return -EIO; 1147 1148 local_irq_save(flags); 1149 if (set & TIOCM_RTS) 1150 info->MCR |= SER_RTS; 1151 if (set & TIOCM_DTR) 1152 info->MCR |= SER_DTR; 1153 if (clear & TIOCM_RTS) 1154 info->MCR &= ~SER_RTS; 1155 if (clear & TIOCM_DTR) 1156 info->MCR &= ~SER_DTR; 1157 rtsdtr_ctrl(info->MCR); 1158 local_irq_restore(flags); 1159 return 0; 1160 } 1161 1162 /* 1163 * rs_break() --- routine which turns the break handling on or off 1164 */ 1165 static int rs_break(struct tty_struct *tty, int break_state) 1166 { 1167 struct serial_state *info = tty->driver_data; 1168 unsigned long flags; 1169 1170 if (serial_paranoia_check(info, tty->name, "rs_break")) 1171 return -EINVAL; 1172 1173 local_irq_save(flags); 1174 if (break_state == -1) 1175 custom.adkcon = AC_SETCLR | AC_UARTBRK; 1176 else 1177 custom.adkcon = AC_UARTBRK; 1178 mb(); 1179 local_irq_restore(flags); 1180 return 0; 1181 } 1182 1183 /* 1184 * Get counter of input serial line interrupts (DCD,RI,DSR,CTS) 1185 * Return: write counters to the user passed counter struct 1186 * NB: both 1->0 and 0->1 transitions are counted except for 1187 * RI where only 0->1 is counted. 1188 */ 1189 static int rs_get_icount(struct tty_struct *tty, 1190 struct serial_icounter_struct *icount) 1191 { 1192 struct serial_state *info = tty->driver_data; 1193 struct async_icount cnow; 1194 unsigned long flags; 1195 1196 local_irq_save(flags); 1197 cnow = info->icount; 1198 local_irq_restore(flags); 1199 icount->cts = cnow.cts; 1200 icount->dsr = cnow.dsr; 1201 icount->rng = cnow.rng; 1202 icount->dcd = cnow.dcd; 1203 icount->rx = cnow.rx; 1204 icount->tx = cnow.tx; 1205 icount->frame = cnow.frame; 1206 icount->overrun = cnow.overrun; 1207 icount->parity = cnow.parity; 1208 icount->brk = cnow.brk; 1209 icount->buf_overrun = cnow.buf_overrun; 1210 1211 return 0; 1212 } 1213 1214 static int rs_ioctl(struct tty_struct *tty, 1215 unsigned int cmd, unsigned long arg) 1216 { 1217 struct serial_state *info = tty->driver_data; 1218 struct async_icount cprev, cnow; /* kernel counter temps */ 1219 void __user *argp = (void __user *)arg; 1220 unsigned long flags; 1221 DEFINE_WAIT(wait); 1222 int ret; 1223 1224 if (serial_paranoia_check(info, tty->name, "rs_ioctl")) 1225 return -ENODEV; 1226 1227 if ((cmd != TIOCGSERIAL) && (cmd != TIOCSSERIAL) && 1228 (cmd != TIOCSERCONFIG) && (cmd != TIOCSERGSTRUCT) && 1229 (cmd != TIOCMIWAIT) && (cmd != TIOCGICOUNT)) { 1230 if (tty_io_error(tty)) 1231 return -EIO; 1232 } 1233 1234 switch (cmd) { 1235 case TIOCGSERIAL: 1236 return get_serial_info(tty, info, argp); 1237 case TIOCSSERIAL: 1238 return set_serial_info(tty, info, argp); 1239 case TIOCSERCONFIG: 1240 return 0; 1241 1242 case TIOCSERGETLSR: /* Get line status register */ 1243 return get_lsr_info(info, argp); 1244 1245 case TIOCSERGSTRUCT: 1246 if (copy_to_user(argp, 1247 info, sizeof(struct serial_state))) 1248 return -EFAULT; 1249 return 0; 1250 1251 /* 1252 * Wait for any of the 4 modem inputs (DCD,RI,DSR,CTS) to change 1253 * - mask passed in arg for lines of interest 1254 * (use |'ed TIOCM_RNG/DSR/CD/CTS for masking) 1255 * Caller should use TIOCGICOUNT to see which one it was 1256 */ 1257 case TIOCMIWAIT: 1258 local_irq_save(flags); 1259 /* note the counters on entry */ 1260 cprev = info->icount; 1261 local_irq_restore(flags); 1262 while (1) { 1263 prepare_to_wait(&info->tport.delta_msr_wait, 1264 &wait, TASK_INTERRUPTIBLE); 1265 local_irq_save(flags); 1266 cnow = info->icount; /* atomic copy */ 1267 local_irq_restore(flags); 1268 if (cnow.rng == cprev.rng && cnow.dsr == cprev.dsr && 1269 cnow.dcd == cprev.dcd && cnow.cts == cprev.cts) { 1270 ret = -EIO; /* no change => error */ 1271 break; 1272 } 1273 if ( ((arg & TIOCM_RNG) && (cnow.rng != cprev.rng)) || 1274 ((arg & TIOCM_DSR) && (cnow.dsr != cprev.dsr)) || 1275 ((arg & TIOCM_CD) && (cnow.dcd != cprev.dcd)) || 1276 ((arg & TIOCM_CTS) && (cnow.cts != cprev.cts)) ) { 1277 ret = 0; 1278 break; 1279 } 1280 schedule(); 1281 /* see if a signal did it */ 1282 if (signal_pending(current)) { 1283 ret = -ERESTARTSYS; 1284 break; 1285 } 1286 cprev = cnow; 1287 } 1288 finish_wait(&info->tport.delta_msr_wait, &wait); 1289 return ret; 1290 1291 case TIOCSERGWILD: 1292 case TIOCSERSWILD: 1293 /* "setserial -W" is called in Debian boot */ 1294 printk ("TIOCSER?WILD ioctl obsolete, ignored.\n"); 1295 return 0; 1296 1297 default: 1298 return -ENOIOCTLCMD; 1299 } 1300 return 0; 1301 } 1302 1303 static void rs_set_termios(struct tty_struct *tty, struct ktermios *old_termios) 1304 { 1305 struct serial_state *info = tty->driver_data; 1306 unsigned long flags; 1307 unsigned int cflag = tty->termios.c_cflag; 1308 1309 change_speed(tty, info, old_termios); 1310 1311 /* Handle transition to B0 status */ 1312 if ((old_termios->c_cflag & CBAUD) && !(cflag & CBAUD)) { 1313 info->MCR &= ~(SER_DTR|SER_RTS); 1314 local_irq_save(flags); 1315 rtsdtr_ctrl(info->MCR); 1316 local_irq_restore(flags); 1317 } 1318 1319 /* Handle transition away from B0 status */ 1320 if (!(old_termios->c_cflag & CBAUD) && (cflag & CBAUD)) { 1321 info->MCR |= SER_DTR; 1322 if (!C_CRTSCTS(tty) || !tty_throttled(tty)) 1323 info->MCR |= SER_RTS; 1324 local_irq_save(flags); 1325 rtsdtr_ctrl(info->MCR); 1326 local_irq_restore(flags); 1327 } 1328 1329 /* Handle turning off CRTSCTS */ 1330 if ((old_termios->c_cflag & CRTSCTS) && !C_CRTSCTS(tty)) { 1331 tty->hw_stopped = 0; 1332 rs_start(tty); 1333 } 1334 1335 #if 0 1336 /* 1337 * No need to wake up processes in open wait, since they 1338 * sample the CLOCAL flag once, and don't recheck it. 1339 * XXX It's not clear whether the current behavior is correct 1340 * or not. Hence, this may change..... 1341 */ 1342 if (!(old_termios->c_cflag & CLOCAL) && C_CLOCAL(tty)) 1343 wake_up_interruptible(&info->open_wait); 1344 #endif 1345 } 1346 1347 /* 1348 * ------------------------------------------------------------ 1349 * rs_close() 1350 * 1351 * This routine is called when the serial port gets closed. First, we 1352 * wait for the last remaining data to be sent. Then, we unlink its 1353 * async structure from the interrupt chain if necessary, and we free 1354 * that IRQ if nothing is left in the chain. 1355 * ------------------------------------------------------------ 1356 */ 1357 static void rs_close(struct tty_struct *tty, struct file * filp) 1358 { 1359 struct serial_state *state = tty->driver_data; 1360 struct tty_port *port = &state->tport; 1361 1362 if (serial_paranoia_check(state, tty->name, "rs_close")) 1363 return; 1364 1365 if (tty_port_close_start(port, tty, filp) == 0) 1366 return; 1367 1368 /* 1369 * At this point we stop accepting input. To do this, we 1370 * disable the receive line status interrupts, and tell the 1371 * interrupt driver to stop checking the data ready bit in the 1372 * line status register. 1373 */ 1374 state->read_status_mask &= ~UART_LSR_DR; 1375 if (tty_port_initialized(port)) { 1376 /* disable receive interrupts */ 1377 custom.intena = IF_RBF; 1378 mb(); 1379 /* clear any pending receive interrupt */ 1380 custom.intreq = IF_RBF; 1381 mb(); 1382 1383 /* 1384 * Before we drop DTR, make sure the UART transmitter 1385 * has completely drained; this is especially 1386 * important if there is a transmit FIFO! 1387 */ 1388 rs_wait_until_sent(tty, state->timeout); 1389 } 1390 shutdown(tty, state); 1391 rs_flush_buffer(tty); 1392 1393 tty_ldisc_flush(tty); 1394 port->tty = NULL; 1395 1396 tty_port_close_end(port, tty); 1397 } 1398 1399 /* 1400 * rs_wait_until_sent() --- wait until the transmitter is empty 1401 */ 1402 static void rs_wait_until_sent(struct tty_struct *tty, int timeout) 1403 { 1404 struct serial_state *info = tty->driver_data; 1405 unsigned long orig_jiffies, char_time; 1406 int lsr; 1407 1408 if (serial_paranoia_check(info, tty->name, "rs_wait_until_sent")) 1409 return; 1410 1411 if (info->xmit_fifo_size == 0) 1412 return; /* Just in case.... */ 1413 1414 orig_jiffies = jiffies; 1415 1416 /* 1417 * Set the check interval to be 1/5 of the estimated time to 1418 * send a single character, and make it at least 1. The check 1419 * interval should also be less than the timeout. 1420 * 1421 * Note: we have to use pretty tight timings here to satisfy 1422 * the NIST-PCTS. 1423 */ 1424 char_time = (info->timeout - HZ/50) / info->xmit_fifo_size; 1425 char_time = char_time / 5; 1426 if (char_time == 0) 1427 char_time = 1; 1428 if (timeout) 1429 char_time = min_t(unsigned long, char_time, timeout); 1430 /* 1431 * If the transmitter hasn't cleared in twice the approximate 1432 * amount of time to send the entire FIFO, it probably won't 1433 * ever clear. This assumes the UART isn't doing flow 1434 * control, which is currently the case. Hence, if it ever 1435 * takes longer than info->timeout, this is probably due to a 1436 * UART bug of some kind. So, we clamp the timeout parameter at 1437 * 2*info->timeout. 1438 */ 1439 if (!timeout || timeout > 2*info->timeout) 1440 timeout = 2*info->timeout; 1441 #ifdef SERIAL_DEBUG_RS_WAIT_UNTIL_SENT 1442 printk("In rs_wait_until_sent(%d) check=%lu...", timeout, char_time); 1443 printk("jiff=%lu...", jiffies); 1444 #endif 1445 while(!((lsr = custom.serdatr) & SDR_TSRE)) { 1446 #ifdef SERIAL_DEBUG_RS_WAIT_UNTIL_SENT 1447 printk("serdatr = %d (jiff=%lu)...", lsr, jiffies); 1448 #endif 1449 msleep_interruptible(jiffies_to_msecs(char_time)); 1450 if (signal_pending(current)) 1451 break; 1452 if (timeout && time_after(jiffies, orig_jiffies + timeout)) 1453 break; 1454 } 1455 __set_current_state(TASK_RUNNING); 1456 1457 #ifdef SERIAL_DEBUG_RS_WAIT_UNTIL_SENT 1458 printk("lsr = %d (jiff=%lu)...done\n", lsr, jiffies); 1459 #endif 1460 } 1461 1462 /* 1463 * rs_hangup() --- called by tty_hangup() when a hangup is signaled. 1464 */ 1465 static void rs_hangup(struct tty_struct *tty) 1466 { 1467 struct serial_state *info = tty->driver_data; 1468 1469 if (serial_paranoia_check(info, tty->name, "rs_hangup")) 1470 return; 1471 1472 rs_flush_buffer(tty); 1473 shutdown(tty, info); 1474 info->tport.count = 0; 1475 tty_port_set_active(&info->tport, 0); 1476 info->tport.tty = NULL; 1477 wake_up_interruptible(&info->tport.open_wait); 1478 } 1479 1480 /* 1481 * This routine is called whenever a serial port is opened. It 1482 * enables interrupts for a serial port, linking in its async structure into 1483 * the IRQ chain. It also performs the serial-specific 1484 * initialization for the tty structure. 1485 */ 1486 static int rs_open(struct tty_struct *tty, struct file * filp) 1487 { 1488 struct serial_state *info = rs_table + tty->index; 1489 struct tty_port *port = &info->tport; 1490 int retval; 1491 1492 port->count++; 1493 port->tty = tty; 1494 tty->driver_data = info; 1495 tty->port = port; 1496 if (serial_paranoia_check(info, tty->name, "rs_open")) 1497 return -ENODEV; 1498 1499 port->low_latency = (port->flags & ASYNC_LOW_LATENCY) ? 1 : 0; 1500 1501 retval = startup(tty, info); 1502 if (retval) { 1503 return retval; 1504 } 1505 1506 return tty_port_block_til_ready(port, tty, filp); 1507 } 1508 1509 /* 1510 * /proc fs routines.... 1511 */ 1512 1513 static inline void line_info(struct seq_file *m, int line, 1514 struct serial_state *state) 1515 { 1516 char stat_buf[30], control, status; 1517 unsigned long flags; 1518 1519 seq_printf(m, "%d: uart:amiga_builtin", line); 1520 1521 local_irq_save(flags); 1522 status = ciab.pra; 1523 control = tty_port_initialized(&state->tport) ? state->MCR : status; 1524 local_irq_restore(flags); 1525 1526 stat_buf[0] = 0; 1527 stat_buf[1] = 0; 1528 if(!(control & SER_RTS)) 1529 strcat(stat_buf, "|RTS"); 1530 if(!(status & SER_CTS)) 1531 strcat(stat_buf, "|CTS"); 1532 if(!(control & SER_DTR)) 1533 strcat(stat_buf, "|DTR"); 1534 if(!(status & SER_DSR)) 1535 strcat(stat_buf, "|DSR"); 1536 if(!(status & SER_DCD)) 1537 strcat(stat_buf, "|CD"); 1538 1539 if (state->quot) 1540 seq_printf(m, " baud:%d", state->baud_base / state->quot); 1541 1542 seq_printf(m, " tx:%d rx:%d", state->icount.tx, state->icount.rx); 1543 1544 if (state->icount.frame) 1545 seq_printf(m, " fe:%d", state->icount.frame); 1546 1547 if (state->icount.parity) 1548 seq_printf(m, " pe:%d", state->icount.parity); 1549 1550 if (state->icount.brk) 1551 seq_printf(m, " brk:%d", state->icount.brk); 1552 1553 if (state->icount.overrun) 1554 seq_printf(m, " oe:%d", state->icount.overrun); 1555 1556 /* 1557 * Last thing is the RS-232 status lines 1558 */ 1559 seq_printf(m, " %s\n", stat_buf+1); 1560 } 1561 1562 static int rs_proc_show(struct seq_file *m, void *v) 1563 { 1564 seq_printf(m, "serinfo:1.0 driver:%s\n", serial_version); 1565 line_info(m, 0, &rs_table[0]); 1566 return 0; 1567 } 1568 1569 /* 1570 * --------------------------------------------------------------------- 1571 * rs_init() and friends 1572 * 1573 * rs_init() is called at boot-time to initialize the serial driver. 1574 * --------------------------------------------------------------------- 1575 */ 1576 1577 /* 1578 * This routine prints out the appropriate serial driver version 1579 * number, and identifies which options were configured into this 1580 * driver. 1581 */ 1582 static void show_serial_version(void) 1583 { 1584 printk(KERN_INFO "%s version %s\n", serial_name, serial_version); 1585 } 1586 1587 1588 static const struct tty_operations serial_ops = { 1589 .open = rs_open, 1590 .close = rs_close, 1591 .write = rs_write, 1592 .put_char = rs_put_char, 1593 .flush_chars = rs_flush_chars, 1594 .write_room = rs_write_room, 1595 .chars_in_buffer = rs_chars_in_buffer, 1596 .flush_buffer = rs_flush_buffer, 1597 .ioctl = rs_ioctl, 1598 .throttle = rs_throttle, 1599 .unthrottle = rs_unthrottle, 1600 .set_termios = rs_set_termios, 1601 .stop = rs_stop, 1602 .start = rs_start, 1603 .hangup = rs_hangup, 1604 .break_ctl = rs_break, 1605 .send_xchar = rs_send_xchar, 1606 .wait_until_sent = rs_wait_until_sent, 1607 .tiocmget = rs_tiocmget, 1608 .tiocmset = rs_tiocmset, 1609 .get_icount = rs_get_icount, 1610 .proc_show = rs_proc_show, 1611 }; 1612 1613 static int amiga_carrier_raised(struct tty_port *port) 1614 { 1615 return !(ciab.pra & SER_DCD); 1616 } 1617 1618 static void amiga_dtr_rts(struct tty_port *port, int raise) 1619 { 1620 struct serial_state *info = container_of(port, struct serial_state, 1621 tport); 1622 unsigned long flags; 1623 1624 if (raise) 1625 info->MCR |= SER_DTR|SER_RTS; 1626 else 1627 info->MCR &= ~(SER_DTR|SER_RTS); 1628 1629 local_irq_save(flags); 1630 rtsdtr_ctrl(info->MCR); 1631 local_irq_restore(flags); 1632 } 1633 1634 static const struct tty_port_operations amiga_port_ops = { 1635 .carrier_raised = amiga_carrier_raised, 1636 .dtr_rts = amiga_dtr_rts, 1637 }; 1638 1639 /* 1640 * The serial driver boot-time initialization code! 1641 */ 1642 static int __init amiga_serial_probe(struct platform_device *pdev) 1643 { 1644 unsigned long flags; 1645 struct serial_state * state; 1646 int error; 1647 1648 serial_driver = alloc_tty_driver(NR_PORTS); 1649 if (!serial_driver) 1650 return -ENOMEM; 1651 1652 show_serial_version(); 1653 1654 /* Initialize the tty_driver structure */ 1655 1656 serial_driver->driver_name = "amiserial"; 1657 serial_driver->name = "ttyS"; 1658 serial_driver->major = TTY_MAJOR; 1659 serial_driver->minor_start = 64; 1660 serial_driver->type = TTY_DRIVER_TYPE_SERIAL; 1661 serial_driver->subtype = SERIAL_TYPE_NORMAL; 1662 serial_driver->init_termios = tty_std_termios; 1663 serial_driver->init_termios.c_cflag = 1664 B9600 | CS8 | CREAD | HUPCL | CLOCAL; 1665 serial_driver->flags = TTY_DRIVER_REAL_RAW; 1666 tty_set_operations(serial_driver, &serial_ops); 1667 1668 state = rs_table; 1669 state->port = (int)&custom.serdatr; /* Just to give it a value */ 1670 state->custom_divisor = 0; 1671 state->icount.cts = state->icount.dsr = 1672 state->icount.rng = state->icount.dcd = 0; 1673 state->icount.rx = state->icount.tx = 0; 1674 state->icount.frame = state->icount.parity = 0; 1675 state->icount.overrun = state->icount.brk = 0; 1676 tty_port_init(&state->tport); 1677 state->tport.ops = &amiga_port_ops; 1678 tty_port_link_device(&state->tport, serial_driver, 0); 1679 1680 error = tty_register_driver(serial_driver); 1681 if (error) 1682 goto fail_put_tty_driver; 1683 1684 printk(KERN_INFO "ttyS0 is the amiga builtin serial port\n"); 1685 1686 /* Hardware set up */ 1687 1688 state->baud_base = amiga_colorclock; 1689 state->xmit_fifo_size = 1; 1690 1691 /* set ISRs, and then disable the rx interrupts */ 1692 error = request_irq(IRQ_AMIGA_TBE, ser_tx_int, 0, "serial TX", state); 1693 if (error) 1694 goto fail_unregister; 1695 1696 error = request_irq(IRQ_AMIGA_RBF, ser_rx_int, 0, 1697 "serial RX", state); 1698 if (error) 1699 goto fail_free_irq; 1700 1701 local_irq_save(flags); 1702 1703 /* turn off Rx and Tx interrupts */ 1704 custom.intena = IF_RBF | IF_TBE; 1705 mb(); 1706 1707 /* clear any pending interrupt */ 1708 custom.intreq = IF_RBF | IF_TBE; 1709 mb(); 1710 1711 local_irq_restore(flags); 1712 1713 /* 1714 * set the appropriate directions for the modem control flags, 1715 * and clear RTS and DTR 1716 */ 1717 ciab.ddra |= (SER_DTR | SER_RTS); /* outputs */ 1718 ciab.ddra &= ~(SER_DCD | SER_CTS | SER_DSR); /* inputs */ 1719 1720 platform_set_drvdata(pdev, state); 1721 1722 return 0; 1723 1724 fail_free_irq: 1725 free_irq(IRQ_AMIGA_TBE, state); 1726 fail_unregister: 1727 tty_unregister_driver(serial_driver); 1728 fail_put_tty_driver: 1729 tty_port_destroy(&state->tport); 1730 put_tty_driver(serial_driver); 1731 return error; 1732 } 1733 1734 static int __exit amiga_serial_remove(struct platform_device *pdev) 1735 { 1736 int error; 1737 struct serial_state *state = platform_get_drvdata(pdev); 1738 1739 /* printk("Unloading %s: version %s\n", serial_name, serial_version); */ 1740 error = tty_unregister_driver(serial_driver); 1741 if (error) 1742 printk("SERIAL: failed to unregister serial driver (%d)\n", 1743 error); 1744 put_tty_driver(serial_driver); 1745 tty_port_destroy(&state->tport); 1746 1747 free_irq(IRQ_AMIGA_TBE, state); 1748 free_irq(IRQ_AMIGA_RBF, state); 1749 1750 return error; 1751 } 1752 1753 static struct platform_driver amiga_serial_driver = { 1754 .remove = __exit_p(amiga_serial_remove), 1755 .driver = { 1756 .name = "amiga-serial", 1757 }, 1758 }; 1759 1760 module_platform_driver_probe(amiga_serial_driver, amiga_serial_probe); 1761 1762 1763 #if defined(CONFIG_SERIAL_CONSOLE) && !defined(MODULE) 1764 1765 /* 1766 * ------------------------------------------------------------ 1767 * Serial console driver 1768 * ------------------------------------------------------------ 1769 */ 1770 1771 static void amiga_serial_putc(char c) 1772 { 1773 custom.serdat = (unsigned char)c | 0x100; 1774 while (!(custom.serdatr & 0x2000)) 1775 barrier(); 1776 } 1777 1778 /* 1779 * Print a string to the serial port trying not to disturb 1780 * any possible real use of the port... 1781 * 1782 * The console must be locked when we get here. 1783 */ 1784 static void serial_console_write(struct console *co, const char *s, 1785 unsigned count) 1786 { 1787 unsigned short intena = custom.intenar; 1788 1789 custom.intena = IF_TBE; 1790 1791 while (count--) { 1792 if (*s == '\n') 1793 amiga_serial_putc('\r'); 1794 amiga_serial_putc(*s++); 1795 } 1796 1797 custom.intena = IF_SETCLR | (intena & IF_TBE); 1798 } 1799 1800 static struct tty_driver *serial_console_device(struct console *c, int *index) 1801 { 1802 *index = 0; 1803 return serial_driver; 1804 } 1805 1806 static struct console sercons = { 1807 .name = "ttyS", 1808 .write = serial_console_write, 1809 .device = serial_console_device, 1810 .flags = CON_PRINTBUFFER, 1811 .index = -1, 1812 }; 1813 1814 /* 1815 * Register console. 1816 */ 1817 static int __init amiserial_console_init(void) 1818 { 1819 if (!MACH_IS_AMIGA) 1820 return -ENODEV; 1821 1822 register_console(&sercons); 1823 return 0; 1824 } 1825 console_initcall(amiserial_console_init); 1826 1827 #endif /* CONFIG_SERIAL_CONSOLE && !MODULE */ 1828 1829 MODULE_LICENSE("GPL"); 1830 MODULE_ALIAS("platform:amiga-serial"); 1831