1 // SPDX-License-Identifier: GPL-2.0 2 /* 3 * Serial driver for the amiga builtin port. 4 * 5 * This code was created by taking serial.c version 4.30 from kernel 6 * release 2.3.22, replacing all hardware related stuff with the 7 * corresponding amiga hardware actions, and removing all irrelevant 8 * code. As a consequence, it uses many of the constants and names 9 * associated with the registers and bits of 16550 compatible UARTS - 10 * but only to keep track of status, etc in the state variables. It 11 * was done this was to make it easier to keep the code in line with 12 * (non hardware specific) changes to serial.c. 13 * 14 * The port is registered with the tty driver as minor device 64, and 15 * therefore other ports should should only use 65 upwards. 16 * 17 * Richard Lucock 28/12/99 18 * 19 * Copyright (C) 1991, 1992 Linus Torvalds 20 * Copyright (C) 1992, 1993, 1994, 1995, 1996, 1997, 21 * 1998, 1999 Theodore Ts'o 22 * 23 */ 24 25 #include <linux/delay.h> 26 27 /* Set of debugging defines */ 28 29 #undef SERIAL_DEBUG_INTR 30 #undef SERIAL_DEBUG_OPEN 31 #undef SERIAL_DEBUG_FLOW 32 #undef SERIAL_DEBUG_RS_WAIT_UNTIL_SENT 33 34 /* Sanity checks */ 35 36 #if defined(MODULE) && defined(SERIAL_DEBUG_MCOUNT) 37 #define DBG_CNT(s) printk("(%s): [%x] refc=%d, serc=%d, ttyc=%d -> %s\n", \ 38 tty->name, (info->tport.flags), serial_driver->refcount,info->count,tty->count,s) 39 #else 40 #define DBG_CNT(s) 41 #endif 42 43 /* 44 * End of serial driver configuration section. 45 */ 46 47 #include <linux/module.h> 48 49 #include <linux/types.h> 50 #include <linux/serial.h> 51 #include <linux/serial_reg.h> 52 static char *serial_version = "4.30"; 53 54 #include <linux/errno.h> 55 #include <linux/signal.h> 56 #include <linux/sched.h> 57 #include <linux/kernel.h> 58 #include <linux/timer.h> 59 #include <linux/interrupt.h> 60 #include <linux/tty.h> 61 #include <linux/tty_flip.h> 62 #include <linux/circ_buf.h> 63 #include <linux/console.h> 64 #include <linux/major.h> 65 #include <linux/string.h> 66 #include <linux/fcntl.h> 67 #include <linux/ptrace.h> 68 #include <linux/ioport.h> 69 #include <linux/mm.h> 70 #include <linux/seq_file.h> 71 #include <linux/slab.h> 72 #include <linux/init.h> 73 #include <linux/bitops.h> 74 #include <linux/platform_device.h> 75 76 #include <asm/setup.h> 77 78 79 #include <asm/irq.h> 80 81 #include <asm/amigahw.h> 82 #include <asm/amigaints.h> 83 84 struct serial_state { 85 struct tty_port tport; 86 struct circ_buf xmit; 87 struct async_icount icount; 88 89 unsigned long port; 90 int baud_base; 91 int xmit_fifo_size; 92 int custom_divisor; 93 int read_status_mask; 94 int ignore_status_mask; 95 int timeout; 96 int quot; 97 int IER; /* Interrupt Enable Register */ 98 int MCR; /* Modem control register */ 99 int x_char; /* xon/xoff character */ 100 }; 101 102 #define custom amiga_custom 103 static char *serial_name = "Amiga-builtin serial driver"; 104 105 static struct tty_driver *serial_driver; 106 107 /* number of characters left in xmit buffer before we ask for more */ 108 #define WAKEUP_CHARS 256 109 110 static unsigned char current_ctl_bits; 111 112 static void change_speed(struct tty_struct *tty, struct serial_state *info, 113 struct ktermios *old); 114 static void rs_wait_until_sent(struct tty_struct *tty, int timeout); 115 116 117 static struct serial_state rs_table[1]; 118 119 #define NR_PORTS ARRAY_SIZE(rs_table) 120 121 #include <linux/uaccess.h> 122 123 #define serial_isroot() (capable(CAP_SYS_ADMIN)) 124 125 /* some serial hardware definitions */ 126 #define SDR_OVRUN (1<<15) 127 #define SDR_RBF (1<<14) 128 #define SDR_TBE (1<<13) 129 #define SDR_TSRE (1<<12) 130 131 #define SERPER_PARENB (1<<15) 132 133 #define AC_SETCLR (1<<15) 134 #define AC_UARTBRK (1<<11) 135 136 #define SER_DTR (1<<7) 137 #define SER_RTS (1<<6) 138 #define SER_DCD (1<<5) 139 #define SER_CTS (1<<4) 140 #define SER_DSR (1<<3) 141 142 static __inline__ void rtsdtr_ctrl(int bits) 143 { 144 ciab.pra = ((bits & (SER_RTS | SER_DTR)) ^ (SER_RTS | SER_DTR)) | (ciab.pra & ~(SER_RTS | SER_DTR)); 145 } 146 147 /* 148 * ------------------------------------------------------------ 149 * rs_stop() and rs_start() 150 * 151 * This routines are called before setting or resetting tty->stopped. 152 * They enable or disable transmitter interrupts, as necessary. 153 * ------------------------------------------------------------ 154 */ 155 static void rs_stop(struct tty_struct *tty) 156 { 157 struct serial_state *info = tty->driver_data; 158 unsigned long flags; 159 160 local_irq_save(flags); 161 if (info->IER & UART_IER_THRI) { 162 info->IER &= ~UART_IER_THRI; 163 /* disable Tx interrupt and remove any pending interrupts */ 164 custom.intena = IF_TBE; 165 mb(); 166 custom.intreq = IF_TBE; 167 mb(); 168 } 169 local_irq_restore(flags); 170 } 171 172 static void rs_start(struct tty_struct *tty) 173 { 174 struct serial_state *info = tty->driver_data; 175 unsigned long flags; 176 177 local_irq_save(flags); 178 if (info->xmit.head != info->xmit.tail 179 && info->xmit.buf 180 && !(info->IER & UART_IER_THRI)) { 181 info->IER |= UART_IER_THRI; 182 custom.intena = IF_SETCLR | IF_TBE; 183 mb(); 184 /* set a pending Tx Interrupt, transmitter should restart now */ 185 custom.intreq = IF_SETCLR | IF_TBE; 186 mb(); 187 } 188 local_irq_restore(flags); 189 } 190 191 /* 192 * ---------------------------------------------------------------------- 193 * 194 * Here starts the interrupt handling routines. All of the following 195 * subroutines are declared as inline and are folded into 196 * rs_interrupt(). They were separated out for readability's sake. 197 * 198 * Note: rs_interrupt() is a "fast" interrupt, which means that it 199 * runs with interrupts turned off. People who may want to modify 200 * rs_interrupt() should try to keep the interrupt handler as fast as 201 * possible. After you are done making modifications, it is not a bad 202 * idea to do: 203 * 204 * gcc -S -DKERNEL -Wall -Wstrict-prototypes -O6 -fomit-frame-pointer serial.c 205 * 206 * and look at the resulting assemble code in serial.s. 207 * 208 * - Ted Ts'o (tytso@mit.edu), 7-Mar-93 209 * ----------------------------------------------------------------------- 210 */ 211 212 static void receive_chars(struct serial_state *info) 213 { 214 int status; 215 int serdatr; 216 unsigned char ch, flag; 217 struct async_icount *icount; 218 int oe = 0; 219 220 icount = &info->icount; 221 222 status = UART_LSR_DR; /* We obviously have a character! */ 223 serdatr = custom.serdatr; 224 mb(); 225 custom.intreq = IF_RBF; 226 mb(); 227 228 if((serdatr & 0x1ff) == 0) 229 status |= UART_LSR_BI; 230 if(serdatr & SDR_OVRUN) 231 status |= UART_LSR_OE; 232 233 ch = serdatr & 0xff; 234 icount->rx++; 235 236 #ifdef SERIAL_DEBUG_INTR 237 printk("DR%02x:%02x...", ch, status); 238 #endif 239 flag = TTY_NORMAL; 240 241 /* 242 * We don't handle parity or frame errors - but I have left 243 * the code in, since I'm not sure that the errors can't be 244 * detected. 245 */ 246 247 if (status & (UART_LSR_BI | UART_LSR_PE | 248 UART_LSR_FE | UART_LSR_OE)) { 249 /* 250 * For statistics only 251 */ 252 if (status & UART_LSR_BI) { 253 status &= ~(UART_LSR_FE | UART_LSR_PE); 254 icount->brk++; 255 } else if (status & UART_LSR_PE) 256 icount->parity++; 257 else if (status & UART_LSR_FE) 258 icount->frame++; 259 if (status & UART_LSR_OE) 260 icount->overrun++; 261 262 /* 263 * Now check to see if character should be 264 * ignored, and mask off conditions which 265 * should be ignored. 266 */ 267 if (status & info->ignore_status_mask) 268 goto out; 269 270 status &= info->read_status_mask; 271 272 if (status & (UART_LSR_BI)) { 273 #ifdef SERIAL_DEBUG_INTR 274 printk("handling break...."); 275 #endif 276 flag = TTY_BREAK; 277 if (info->tport.flags & ASYNC_SAK) 278 do_SAK(info->tport.tty); 279 } else if (status & UART_LSR_PE) 280 flag = TTY_PARITY; 281 else if (status & UART_LSR_FE) 282 flag = TTY_FRAME; 283 if (status & UART_LSR_OE) { 284 /* 285 * Overrun is special, since it's 286 * reported immediately, and doesn't 287 * affect the current character 288 */ 289 oe = 1; 290 } 291 } 292 tty_insert_flip_char(&info->tport, ch, flag); 293 if (oe == 1) 294 tty_insert_flip_char(&info->tport, 0, TTY_OVERRUN); 295 tty_flip_buffer_push(&info->tport); 296 out: 297 return; 298 } 299 300 static void transmit_chars(struct serial_state *info) 301 { 302 custom.intreq = IF_TBE; 303 mb(); 304 if (info->x_char) { 305 custom.serdat = info->x_char | 0x100; 306 mb(); 307 info->icount.tx++; 308 info->x_char = 0; 309 return; 310 } 311 if (info->xmit.head == info->xmit.tail 312 || info->tport.tty->stopped 313 || info->tport.tty->hw_stopped) { 314 info->IER &= ~UART_IER_THRI; 315 custom.intena = IF_TBE; 316 mb(); 317 return; 318 } 319 320 custom.serdat = info->xmit.buf[info->xmit.tail++] | 0x100; 321 mb(); 322 info->xmit.tail = info->xmit.tail & (SERIAL_XMIT_SIZE-1); 323 info->icount.tx++; 324 325 if (CIRC_CNT(info->xmit.head, 326 info->xmit.tail, 327 SERIAL_XMIT_SIZE) < WAKEUP_CHARS) 328 tty_wakeup(info->tport.tty); 329 330 #ifdef SERIAL_DEBUG_INTR 331 printk("THRE..."); 332 #endif 333 if (info->xmit.head == info->xmit.tail) { 334 custom.intena = IF_TBE; 335 mb(); 336 info->IER &= ~UART_IER_THRI; 337 } 338 } 339 340 static void check_modem_status(struct serial_state *info) 341 { 342 struct tty_port *port = &info->tport; 343 unsigned char status = ciab.pra & (SER_DCD | SER_CTS | SER_DSR); 344 unsigned char dstatus; 345 struct async_icount *icount; 346 347 /* Determine bits that have changed */ 348 dstatus = status ^ current_ctl_bits; 349 current_ctl_bits = status; 350 351 if (dstatus) { 352 icount = &info->icount; 353 /* update input line counters */ 354 if (dstatus & SER_DSR) 355 icount->dsr++; 356 if (dstatus & SER_DCD) { 357 icount->dcd++; 358 } 359 if (dstatus & SER_CTS) 360 icount->cts++; 361 wake_up_interruptible(&port->delta_msr_wait); 362 } 363 364 if (tty_port_check_carrier(port) && (dstatus & SER_DCD)) { 365 #if (defined(SERIAL_DEBUG_OPEN) || defined(SERIAL_DEBUG_INTR)) 366 printk("ttyS%d CD now %s...", info->line, 367 (!(status & SER_DCD)) ? "on" : "off"); 368 #endif 369 if (!(status & SER_DCD)) 370 wake_up_interruptible(&port->open_wait); 371 else { 372 #ifdef SERIAL_DEBUG_OPEN 373 printk("doing serial hangup..."); 374 #endif 375 if (port->tty) 376 tty_hangup(port->tty); 377 } 378 } 379 if (tty_port_cts_enabled(port)) { 380 if (port->tty->hw_stopped) { 381 if (!(status & SER_CTS)) { 382 #if (defined(SERIAL_DEBUG_INTR) || defined(SERIAL_DEBUG_FLOW)) 383 printk("CTS tx start..."); 384 #endif 385 port->tty->hw_stopped = 0; 386 info->IER |= UART_IER_THRI; 387 custom.intena = IF_SETCLR | IF_TBE; 388 mb(); 389 /* set a pending Tx Interrupt, transmitter should restart now */ 390 custom.intreq = IF_SETCLR | IF_TBE; 391 mb(); 392 tty_wakeup(port->tty); 393 return; 394 } 395 } else { 396 if ((status & SER_CTS)) { 397 #if (defined(SERIAL_DEBUG_INTR) || defined(SERIAL_DEBUG_FLOW)) 398 printk("CTS tx stop..."); 399 #endif 400 port->tty->hw_stopped = 1; 401 info->IER &= ~UART_IER_THRI; 402 /* disable Tx interrupt and remove any pending interrupts */ 403 custom.intena = IF_TBE; 404 mb(); 405 custom.intreq = IF_TBE; 406 mb(); 407 } 408 } 409 } 410 } 411 412 static irqreturn_t ser_vbl_int( int irq, void *data) 413 { 414 /* vbl is just a periodic interrupt we tie into to update modem status */ 415 struct serial_state *info = data; 416 /* 417 * TBD - is it better to unregister from this interrupt or to 418 * ignore it if MSI is clear ? 419 */ 420 if(info->IER & UART_IER_MSI) 421 check_modem_status(info); 422 return IRQ_HANDLED; 423 } 424 425 static irqreturn_t ser_rx_int(int irq, void *dev_id) 426 { 427 struct serial_state *info = dev_id; 428 429 #ifdef SERIAL_DEBUG_INTR 430 printk("ser_rx_int..."); 431 #endif 432 433 if (!info->tport.tty) 434 return IRQ_NONE; 435 436 receive_chars(info); 437 #ifdef SERIAL_DEBUG_INTR 438 printk("end.\n"); 439 #endif 440 return IRQ_HANDLED; 441 } 442 443 static irqreturn_t ser_tx_int(int irq, void *dev_id) 444 { 445 struct serial_state *info = dev_id; 446 447 if (custom.serdatr & SDR_TBE) { 448 #ifdef SERIAL_DEBUG_INTR 449 printk("ser_tx_int..."); 450 #endif 451 452 if (!info->tport.tty) 453 return IRQ_NONE; 454 455 transmit_chars(info); 456 #ifdef SERIAL_DEBUG_INTR 457 printk("end.\n"); 458 #endif 459 } 460 return IRQ_HANDLED; 461 } 462 463 /* 464 * ------------------------------------------------------------------- 465 * Here ends the serial interrupt routines. 466 * ------------------------------------------------------------------- 467 */ 468 469 /* 470 * --------------------------------------------------------------- 471 * Low level utility subroutines for the serial driver: routines to 472 * figure out the appropriate timeout for an interrupt chain, routines 473 * to initialize and startup a serial port, and routines to shutdown a 474 * serial port. Useful stuff like that. 475 * --------------------------------------------------------------- 476 */ 477 478 static int startup(struct tty_struct *tty, struct serial_state *info) 479 { 480 struct tty_port *port = &info->tport; 481 unsigned long flags; 482 int retval=0; 483 unsigned long page; 484 485 page = get_zeroed_page(GFP_KERNEL); 486 if (!page) 487 return -ENOMEM; 488 489 local_irq_save(flags); 490 491 if (tty_port_initialized(port)) { 492 free_page(page); 493 goto errout; 494 } 495 496 if (info->xmit.buf) 497 free_page(page); 498 else 499 info->xmit.buf = (unsigned char *) page; 500 501 #ifdef SERIAL_DEBUG_OPEN 502 printk("starting up ttys%d ...", info->line); 503 #endif 504 505 /* Clear anything in the input buffer */ 506 507 custom.intreq = IF_RBF; 508 mb(); 509 510 retval = request_irq(IRQ_AMIGA_VERTB, ser_vbl_int, 0, "serial status", info); 511 if (retval) { 512 if (serial_isroot()) { 513 set_bit(TTY_IO_ERROR, &tty->flags); 514 retval = 0; 515 } 516 goto errout; 517 } 518 519 /* enable both Rx and Tx interrupts */ 520 custom.intena = IF_SETCLR | IF_RBF | IF_TBE; 521 mb(); 522 info->IER = UART_IER_MSI; 523 524 /* remember current state of the DCD and CTS bits */ 525 current_ctl_bits = ciab.pra & (SER_DCD | SER_CTS | SER_DSR); 526 527 info->MCR = 0; 528 if (C_BAUD(tty)) 529 info->MCR = SER_DTR | SER_RTS; 530 rtsdtr_ctrl(info->MCR); 531 532 clear_bit(TTY_IO_ERROR, &tty->flags); 533 info->xmit.head = info->xmit.tail = 0; 534 535 /* 536 * and set the speed of the serial port 537 */ 538 change_speed(tty, info, NULL); 539 540 tty_port_set_initialized(port, 1); 541 local_irq_restore(flags); 542 return 0; 543 544 errout: 545 local_irq_restore(flags); 546 return retval; 547 } 548 549 /* 550 * This routine will shutdown a serial port; interrupts are disabled, and 551 * DTR is dropped if the hangup on close termio flag is on. 552 */ 553 static void shutdown(struct tty_struct *tty, struct serial_state *info) 554 { 555 unsigned long flags; 556 struct serial_state *state; 557 558 if (!tty_port_initialized(&info->tport)) 559 return; 560 561 state = info; 562 563 #ifdef SERIAL_DEBUG_OPEN 564 printk("Shutting down serial port %d ....\n", info->line); 565 #endif 566 567 local_irq_save(flags); /* Disable interrupts */ 568 569 /* 570 * clear delta_msr_wait queue to avoid mem leaks: we may free the irq 571 * here so the queue might never be waken up 572 */ 573 wake_up_interruptible(&info->tport.delta_msr_wait); 574 575 /* 576 * Free the IRQ, if necessary 577 */ 578 free_irq(IRQ_AMIGA_VERTB, info); 579 580 if (info->xmit.buf) { 581 free_page((unsigned long) info->xmit.buf); 582 info->xmit.buf = NULL; 583 } 584 585 info->IER = 0; 586 custom.intena = IF_RBF | IF_TBE; 587 mb(); 588 589 /* disable break condition */ 590 custom.adkcon = AC_UARTBRK; 591 mb(); 592 593 if (C_HUPCL(tty)) 594 info->MCR &= ~(SER_DTR|SER_RTS); 595 rtsdtr_ctrl(info->MCR); 596 597 set_bit(TTY_IO_ERROR, &tty->flags); 598 599 tty_port_set_initialized(&info->tport, 0); 600 local_irq_restore(flags); 601 } 602 603 604 /* 605 * This routine is called to set the UART divisor registers to match 606 * the specified baud rate for a serial port. 607 */ 608 static void change_speed(struct tty_struct *tty, struct serial_state *info, 609 struct ktermios *old_termios) 610 { 611 struct tty_port *port = &info->tport; 612 int quot = 0, baud_base, baud; 613 unsigned cflag, cval = 0; 614 int bits; 615 unsigned long flags; 616 617 cflag = tty->termios.c_cflag; 618 619 /* Byte size is always 8 bits plus parity bit if requested */ 620 621 cval = 3; bits = 10; 622 if (cflag & CSTOPB) { 623 cval |= 0x04; 624 bits++; 625 } 626 if (cflag & PARENB) { 627 cval |= UART_LCR_PARITY; 628 bits++; 629 } 630 if (!(cflag & PARODD)) 631 cval |= UART_LCR_EPAR; 632 #ifdef CMSPAR 633 if (cflag & CMSPAR) 634 cval |= UART_LCR_SPAR; 635 #endif 636 637 /* Determine divisor based on baud rate */ 638 baud = tty_get_baud_rate(tty); 639 if (!baud) 640 baud = 9600; /* B0 transition handled in rs_set_termios */ 641 baud_base = info->baud_base; 642 if (baud == 38400 && (port->flags & ASYNC_SPD_MASK) == ASYNC_SPD_CUST) 643 quot = info->custom_divisor; 644 else { 645 if (baud == 134) 646 /* Special case since 134 is really 134.5 */ 647 quot = (2*baud_base / 269); 648 else if (baud) 649 quot = baud_base / baud; 650 } 651 /* If the quotient is zero refuse the change */ 652 if (!quot && old_termios) { 653 /* FIXME: Will need updating for new tty in the end */ 654 tty->termios.c_cflag &= ~CBAUD; 655 tty->termios.c_cflag |= (old_termios->c_cflag & CBAUD); 656 baud = tty_get_baud_rate(tty); 657 if (!baud) 658 baud = 9600; 659 if (baud == 38400 && 660 (port->flags & ASYNC_SPD_MASK) == ASYNC_SPD_CUST) 661 quot = info->custom_divisor; 662 else { 663 if (baud == 134) 664 /* Special case since 134 is really 134.5 */ 665 quot = (2*baud_base / 269); 666 else if (baud) 667 quot = baud_base / baud; 668 } 669 } 670 /* As a last resort, if the quotient is zero, default to 9600 bps */ 671 if (!quot) 672 quot = baud_base / 9600; 673 info->quot = quot; 674 info->timeout = ((info->xmit_fifo_size*HZ*bits*quot) / baud_base); 675 info->timeout += HZ/50; /* Add .02 seconds of slop */ 676 677 /* CTS flow control flag and modem status interrupts */ 678 info->IER &= ~UART_IER_MSI; 679 if (port->flags & ASYNC_HARDPPS_CD) 680 info->IER |= UART_IER_MSI; 681 tty_port_set_cts_flow(port, cflag & CRTSCTS); 682 if (cflag & CRTSCTS) 683 info->IER |= UART_IER_MSI; 684 tty_port_set_check_carrier(port, ~cflag & CLOCAL); 685 if (~cflag & CLOCAL) 686 info->IER |= UART_IER_MSI; 687 /* TBD: 688 * Does clearing IER_MSI imply that we should disable the VBL interrupt ? 689 */ 690 691 /* 692 * Set up parity check flag 693 */ 694 695 info->read_status_mask = UART_LSR_OE | UART_LSR_DR; 696 if (I_INPCK(tty)) 697 info->read_status_mask |= UART_LSR_FE | UART_LSR_PE; 698 if (I_BRKINT(tty) || I_PARMRK(tty)) 699 info->read_status_mask |= UART_LSR_BI; 700 701 /* 702 * Characters to ignore 703 */ 704 info->ignore_status_mask = 0; 705 if (I_IGNPAR(tty)) 706 info->ignore_status_mask |= UART_LSR_PE | UART_LSR_FE; 707 if (I_IGNBRK(tty)) { 708 info->ignore_status_mask |= UART_LSR_BI; 709 /* 710 * If we're ignore parity and break indicators, ignore 711 * overruns too. (For real raw support). 712 */ 713 if (I_IGNPAR(tty)) 714 info->ignore_status_mask |= UART_LSR_OE; 715 } 716 /* 717 * !!! ignore all characters if CREAD is not set 718 */ 719 if ((cflag & CREAD) == 0) 720 info->ignore_status_mask |= UART_LSR_DR; 721 local_irq_save(flags); 722 723 { 724 short serper; 725 726 /* Set up the baud rate */ 727 serper = quot - 1; 728 729 /* Enable or disable parity bit */ 730 731 if(cval & UART_LCR_PARITY) 732 serper |= (SERPER_PARENB); 733 734 custom.serper = serper; 735 mb(); 736 } 737 738 local_irq_restore(flags); 739 } 740 741 static int rs_put_char(struct tty_struct *tty, unsigned char ch) 742 { 743 struct serial_state *info; 744 unsigned long flags; 745 746 info = tty->driver_data; 747 748 if (!info->xmit.buf) 749 return 0; 750 751 local_irq_save(flags); 752 if (CIRC_SPACE(info->xmit.head, 753 info->xmit.tail, 754 SERIAL_XMIT_SIZE) == 0) { 755 local_irq_restore(flags); 756 return 0; 757 } 758 759 info->xmit.buf[info->xmit.head++] = ch; 760 info->xmit.head &= SERIAL_XMIT_SIZE-1; 761 local_irq_restore(flags); 762 return 1; 763 } 764 765 static void rs_flush_chars(struct tty_struct *tty) 766 { 767 struct serial_state *info = tty->driver_data; 768 unsigned long flags; 769 770 if (info->xmit.head == info->xmit.tail 771 || tty->stopped 772 || tty->hw_stopped 773 || !info->xmit.buf) 774 return; 775 776 local_irq_save(flags); 777 info->IER |= UART_IER_THRI; 778 custom.intena = IF_SETCLR | IF_TBE; 779 mb(); 780 /* set a pending Tx Interrupt, transmitter should restart now */ 781 custom.intreq = IF_SETCLR | IF_TBE; 782 mb(); 783 local_irq_restore(flags); 784 } 785 786 static int rs_write(struct tty_struct * tty, const unsigned char *buf, int count) 787 { 788 int c, ret = 0; 789 struct serial_state *info = tty->driver_data; 790 unsigned long flags; 791 792 if (!info->xmit.buf) 793 return 0; 794 795 local_irq_save(flags); 796 while (1) { 797 c = CIRC_SPACE_TO_END(info->xmit.head, 798 info->xmit.tail, 799 SERIAL_XMIT_SIZE); 800 if (count < c) 801 c = count; 802 if (c <= 0) { 803 break; 804 } 805 memcpy(info->xmit.buf + info->xmit.head, buf, c); 806 info->xmit.head = ((info->xmit.head + c) & 807 (SERIAL_XMIT_SIZE-1)); 808 buf += c; 809 count -= c; 810 ret += c; 811 } 812 local_irq_restore(flags); 813 814 if (info->xmit.head != info->xmit.tail 815 && !tty->stopped 816 && !tty->hw_stopped 817 && !(info->IER & UART_IER_THRI)) { 818 info->IER |= UART_IER_THRI; 819 local_irq_disable(); 820 custom.intena = IF_SETCLR | IF_TBE; 821 mb(); 822 /* set a pending Tx Interrupt, transmitter should restart now */ 823 custom.intreq = IF_SETCLR | IF_TBE; 824 mb(); 825 local_irq_restore(flags); 826 } 827 return ret; 828 } 829 830 static int rs_write_room(struct tty_struct *tty) 831 { 832 struct serial_state *info = tty->driver_data; 833 834 return CIRC_SPACE(info->xmit.head, info->xmit.tail, SERIAL_XMIT_SIZE); 835 } 836 837 static int rs_chars_in_buffer(struct tty_struct *tty) 838 { 839 struct serial_state *info = tty->driver_data; 840 841 return CIRC_CNT(info->xmit.head, info->xmit.tail, SERIAL_XMIT_SIZE); 842 } 843 844 static void rs_flush_buffer(struct tty_struct *tty) 845 { 846 struct serial_state *info = tty->driver_data; 847 unsigned long flags; 848 849 local_irq_save(flags); 850 info->xmit.head = info->xmit.tail = 0; 851 local_irq_restore(flags); 852 tty_wakeup(tty); 853 } 854 855 /* 856 * This function is used to send a high-priority XON/XOFF character to 857 * the device 858 */ 859 static void rs_send_xchar(struct tty_struct *tty, char ch) 860 { 861 struct serial_state *info = tty->driver_data; 862 unsigned long flags; 863 864 info->x_char = ch; 865 if (ch) { 866 /* Make sure transmit interrupts are on */ 867 868 /* Check this ! */ 869 local_irq_save(flags); 870 if(!(custom.intenar & IF_TBE)) { 871 custom.intena = IF_SETCLR | IF_TBE; 872 mb(); 873 /* set a pending Tx Interrupt, transmitter should restart now */ 874 custom.intreq = IF_SETCLR | IF_TBE; 875 mb(); 876 } 877 local_irq_restore(flags); 878 879 info->IER |= UART_IER_THRI; 880 } 881 } 882 883 /* 884 * ------------------------------------------------------------ 885 * rs_throttle() 886 * 887 * This routine is called by the upper-layer tty layer to signal that 888 * incoming characters should be throttled. 889 * ------------------------------------------------------------ 890 */ 891 static void rs_throttle(struct tty_struct * tty) 892 { 893 struct serial_state *info = tty->driver_data; 894 unsigned long flags; 895 #ifdef SERIAL_DEBUG_THROTTLE 896 printk("throttle %s ....\n", tty_name(tty)); 897 #endif 898 899 if (I_IXOFF(tty)) 900 rs_send_xchar(tty, STOP_CHAR(tty)); 901 902 if (C_CRTSCTS(tty)) 903 info->MCR &= ~SER_RTS; 904 905 local_irq_save(flags); 906 rtsdtr_ctrl(info->MCR); 907 local_irq_restore(flags); 908 } 909 910 static void rs_unthrottle(struct tty_struct * tty) 911 { 912 struct serial_state *info = tty->driver_data; 913 unsigned long flags; 914 #ifdef SERIAL_DEBUG_THROTTLE 915 printk("unthrottle %s ....\n", tty_name(tty)); 916 #endif 917 918 if (I_IXOFF(tty)) { 919 if (info->x_char) 920 info->x_char = 0; 921 else 922 rs_send_xchar(tty, START_CHAR(tty)); 923 } 924 if (C_CRTSCTS(tty)) 925 info->MCR |= SER_RTS; 926 local_irq_save(flags); 927 rtsdtr_ctrl(info->MCR); 928 local_irq_restore(flags); 929 } 930 931 /* 932 * ------------------------------------------------------------ 933 * rs_ioctl() and friends 934 * ------------------------------------------------------------ 935 */ 936 937 static int get_serial_info(struct tty_struct *tty, struct serial_struct *ss) 938 { 939 struct serial_state *state = tty->driver_data; 940 unsigned int close_delay, closing_wait; 941 942 tty_lock(tty); 943 close_delay = jiffies_to_msecs(state->tport.close_delay) / 10; 944 closing_wait = state->tport.closing_wait; 945 if (closing_wait != ASYNC_CLOSING_WAIT_NONE) 946 closing_wait = jiffies_to_msecs(closing_wait) / 10; 947 948 ss->line = tty->index; 949 ss->port = state->port; 950 ss->flags = state->tport.flags; 951 ss->xmit_fifo_size = state->xmit_fifo_size; 952 ss->baud_base = state->baud_base; 953 ss->close_delay = close_delay; 954 ss->closing_wait = closing_wait; 955 ss->custom_divisor = state->custom_divisor; 956 tty_unlock(tty); 957 return 0; 958 } 959 960 static int set_serial_info(struct tty_struct *tty, struct serial_struct *ss) 961 { 962 struct serial_state *state = tty->driver_data; 963 struct tty_port *port = &state->tport; 964 bool change_spd; 965 int retval = 0; 966 unsigned int close_delay, closing_wait; 967 968 tty_lock(tty); 969 change_spd = ((ss->flags ^ port->flags) & ASYNC_SPD_MASK) || 970 ss->custom_divisor != state->custom_divisor; 971 if (ss->irq || ss->port != state->port || 972 ss->xmit_fifo_size != state->xmit_fifo_size) { 973 tty_unlock(tty); 974 return -EINVAL; 975 } 976 977 close_delay = msecs_to_jiffies(ss->close_delay * 10); 978 closing_wait = ss->closing_wait; 979 if (closing_wait != ASYNC_CLOSING_WAIT_NONE) 980 closing_wait = msecs_to_jiffies(closing_wait * 10); 981 982 if (!serial_isroot()) { 983 if ((ss->baud_base != state->baud_base) || 984 (close_delay != port->close_delay) || 985 (closing_wait != port->closing_wait) || 986 (ss->xmit_fifo_size != state->xmit_fifo_size) || 987 ((ss->flags & ~ASYNC_USR_MASK) != 988 (port->flags & ~ASYNC_USR_MASK))) { 989 tty_unlock(tty); 990 return -EPERM; 991 } 992 port->flags = ((port->flags & ~ASYNC_USR_MASK) | 993 (ss->flags & ASYNC_USR_MASK)); 994 state->custom_divisor = ss->custom_divisor; 995 goto check_and_exit; 996 } 997 998 if (ss->baud_base < 9600) { 999 tty_unlock(tty); 1000 return -EINVAL; 1001 } 1002 1003 /* 1004 * OK, past this point, all the error checking has been done. 1005 * At this point, we start making changes..... 1006 */ 1007 1008 state->baud_base = ss->baud_base; 1009 port->flags = ((port->flags & ~ASYNC_FLAGS) | 1010 (ss->flags & ASYNC_FLAGS)); 1011 state->custom_divisor = ss->custom_divisor; 1012 port->close_delay = close_delay; 1013 port->closing_wait = closing_wait; 1014 1015 check_and_exit: 1016 if (tty_port_initialized(port)) { 1017 if (change_spd) { 1018 /* warn about deprecation unless clearing */ 1019 if (ss->flags & ASYNC_SPD_MASK) 1020 dev_warn_ratelimited(tty->dev, "use of SPD flags is deprecated\n"); 1021 change_speed(tty, state, NULL); 1022 } 1023 } else 1024 retval = startup(tty, state); 1025 tty_unlock(tty); 1026 return retval; 1027 } 1028 1029 /* 1030 * get_lsr_info - get line status register info 1031 * 1032 * Purpose: Let user call ioctl() to get info when the UART physically 1033 * is emptied. On bus types like RS485, the transmitter must 1034 * release the bus after transmitting. This must be done when 1035 * the transmit shift register is empty, not be done when the 1036 * transmit holding register is empty. This functionality 1037 * allows an RS485 driver to be written in user space. 1038 */ 1039 static int get_lsr_info(struct serial_state *info, unsigned int __user *value) 1040 { 1041 unsigned char status; 1042 unsigned int result; 1043 unsigned long flags; 1044 1045 local_irq_save(flags); 1046 status = custom.serdatr; 1047 mb(); 1048 local_irq_restore(flags); 1049 result = ((status & SDR_TSRE) ? TIOCSER_TEMT : 0); 1050 if (copy_to_user(value, &result, sizeof(int))) 1051 return -EFAULT; 1052 return 0; 1053 } 1054 1055 1056 static int rs_tiocmget(struct tty_struct *tty) 1057 { 1058 struct serial_state *info = tty->driver_data; 1059 unsigned char control, status; 1060 unsigned long flags; 1061 1062 if (tty_io_error(tty)) 1063 return -EIO; 1064 1065 control = info->MCR; 1066 local_irq_save(flags); 1067 status = ciab.pra; 1068 local_irq_restore(flags); 1069 return ((control & SER_RTS) ? TIOCM_RTS : 0) 1070 | ((control & SER_DTR) ? TIOCM_DTR : 0) 1071 | (!(status & SER_DCD) ? TIOCM_CAR : 0) 1072 | (!(status & SER_DSR) ? TIOCM_DSR : 0) 1073 | (!(status & SER_CTS) ? TIOCM_CTS : 0); 1074 } 1075 1076 static int rs_tiocmset(struct tty_struct *tty, unsigned int set, 1077 unsigned int clear) 1078 { 1079 struct serial_state *info = tty->driver_data; 1080 unsigned long flags; 1081 1082 if (tty_io_error(tty)) 1083 return -EIO; 1084 1085 local_irq_save(flags); 1086 if (set & TIOCM_RTS) 1087 info->MCR |= SER_RTS; 1088 if (set & TIOCM_DTR) 1089 info->MCR |= SER_DTR; 1090 if (clear & TIOCM_RTS) 1091 info->MCR &= ~SER_RTS; 1092 if (clear & TIOCM_DTR) 1093 info->MCR &= ~SER_DTR; 1094 rtsdtr_ctrl(info->MCR); 1095 local_irq_restore(flags); 1096 return 0; 1097 } 1098 1099 /* 1100 * rs_break() --- routine which turns the break handling on or off 1101 */ 1102 static int rs_break(struct tty_struct *tty, int break_state) 1103 { 1104 unsigned long flags; 1105 1106 local_irq_save(flags); 1107 if (break_state == -1) 1108 custom.adkcon = AC_SETCLR | AC_UARTBRK; 1109 else 1110 custom.adkcon = AC_UARTBRK; 1111 mb(); 1112 local_irq_restore(flags); 1113 return 0; 1114 } 1115 1116 /* 1117 * Get counter of input serial line interrupts (DCD,RI,DSR,CTS) 1118 * Return: write counters to the user passed counter struct 1119 * NB: both 1->0 and 0->1 transitions are counted except for 1120 * RI where only 0->1 is counted. 1121 */ 1122 static int rs_get_icount(struct tty_struct *tty, 1123 struct serial_icounter_struct *icount) 1124 { 1125 struct serial_state *info = tty->driver_data; 1126 struct async_icount cnow; 1127 unsigned long flags; 1128 1129 local_irq_save(flags); 1130 cnow = info->icount; 1131 local_irq_restore(flags); 1132 icount->cts = cnow.cts; 1133 icount->dsr = cnow.dsr; 1134 icount->rng = cnow.rng; 1135 icount->dcd = cnow.dcd; 1136 icount->rx = cnow.rx; 1137 icount->tx = cnow.tx; 1138 icount->frame = cnow.frame; 1139 icount->overrun = cnow.overrun; 1140 icount->parity = cnow.parity; 1141 icount->brk = cnow.brk; 1142 icount->buf_overrun = cnow.buf_overrun; 1143 1144 return 0; 1145 } 1146 1147 static int rs_ioctl(struct tty_struct *tty, 1148 unsigned int cmd, unsigned long arg) 1149 { 1150 struct serial_state *info = tty->driver_data; 1151 struct async_icount cprev, cnow; /* kernel counter temps */ 1152 void __user *argp = (void __user *)arg; 1153 unsigned long flags; 1154 DEFINE_WAIT(wait); 1155 int ret; 1156 1157 if ((cmd != TIOCSERCONFIG) && 1158 (cmd != TIOCMIWAIT) && (cmd != TIOCGICOUNT)) { 1159 if (tty_io_error(tty)) 1160 return -EIO; 1161 } 1162 1163 switch (cmd) { 1164 case TIOCSERCONFIG: 1165 return 0; 1166 1167 case TIOCSERGETLSR: /* Get line status register */ 1168 return get_lsr_info(info, argp); 1169 1170 /* 1171 * Wait for any of the 4 modem inputs (DCD,RI,DSR,CTS) to change 1172 * - mask passed in arg for lines of interest 1173 * (use |'ed TIOCM_RNG/DSR/CD/CTS for masking) 1174 * Caller should use TIOCGICOUNT to see which one it was 1175 */ 1176 case TIOCMIWAIT: 1177 local_irq_save(flags); 1178 /* note the counters on entry */ 1179 cprev = info->icount; 1180 local_irq_restore(flags); 1181 while (1) { 1182 prepare_to_wait(&info->tport.delta_msr_wait, 1183 &wait, TASK_INTERRUPTIBLE); 1184 local_irq_save(flags); 1185 cnow = info->icount; /* atomic copy */ 1186 local_irq_restore(flags); 1187 if (cnow.rng == cprev.rng && cnow.dsr == cprev.dsr && 1188 cnow.dcd == cprev.dcd && cnow.cts == cprev.cts) { 1189 ret = -EIO; /* no change => error */ 1190 break; 1191 } 1192 if ( ((arg & TIOCM_RNG) && (cnow.rng != cprev.rng)) || 1193 ((arg & TIOCM_DSR) && (cnow.dsr != cprev.dsr)) || 1194 ((arg & TIOCM_CD) && (cnow.dcd != cprev.dcd)) || 1195 ((arg & TIOCM_CTS) && (cnow.cts != cprev.cts)) ) { 1196 ret = 0; 1197 break; 1198 } 1199 schedule(); 1200 /* see if a signal did it */ 1201 if (signal_pending(current)) { 1202 ret = -ERESTARTSYS; 1203 break; 1204 } 1205 cprev = cnow; 1206 } 1207 finish_wait(&info->tport.delta_msr_wait, &wait); 1208 return ret; 1209 1210 default: 1211 return -ENOIOCTLCMD; 1212 } 1213 return 0; 1214 } 1215 1216 static void rs_set_termios(struct tty_struct *tty, struct ktermios *old_termios) 1217 { 1218 struct serial_state *info = tty->driver_data; 1219 unsigned long flags; 1220 unsigned int cflag = tty->termios.c_cflag; 1221 1222 change_speed(tty, info, old_termios); 1223 1224 /* Handle transition to B0 status */ 1225 if ((old_termios->c_cflag & CBAUD) && !(cflag & CBAUD)) { 1226 info->MCR &= ~(SER_DTR|SER_RTS); 1227 local_irq_save(flags); 1228 rtsdtr_ctrl(info->MCR); 1229 local_irq_restore(flags); 1230 } 1231 1232 /* Handle transition away from B0 status */ 1233 if (!(old_termios->c_cflag & CBAUD) && (cflag & CBAUD)) { 1234 info->MCR |= SER_DTR; 1235 if (!C_CRTSCTS(tty) || !tty_throttled(tty)) 1236 info->MCR |= SER_RTS; 1237 local_irq_save(flags); 1238 rtsdtr_ctrl(info->MCR); 1239 local_irq_restore(flags); 1240 } 1241 1242 /* Handle turning off CRTSCTS */ 1243 if ((old_termios->c_cflag & CRTSCTS) && !C_CRTSCTS(tty)) { 1244 tty->hw_stopped = 0; 1245 rs_start(tty); 1246 } 1247 1248 #if 0 1249 /* 1250 * No need to wake up processes in open wait, since they 1251 * sample the CLOCAL flag once, and don't recheck it. 1252 * XXX It's not clear whether the current behavior is correct 1253 * or not. Hence, this may change..... 1254 */ 1255 if (!(old_termios->c_cflag & CLOCAL) && C_CLOCAL(tty)) 1256 wake_up_interruptible(&info->open_wait); 1257 #endif 1258 } 1259 1260 /* 1261 * ------------------------------------------------------------ 1262 * rs_close() 1263 * 1264 * This routine is called when the serial port gets closed. First, we 1265 * wait for the last remaining data to be sent. Then, we unlink its 1266 * async structure from the interrupt chain if necessary, and we free 1267 * that IRQ if nothing is left in the chain. 1268 * ------------------------------------------------------------ 1269 */ 1270 static void rs_close(struct tty_struct *tty, struct file * filp) 1271 { 1272 struct serial_state *state = tty->driver_data; 1273 struct tty_port *port = &state->tport; 1274 1275 if (tty_port_close_start(port, tty, filp) == 0) 1276 return; 1277 1278 /* 1279 * At this point we stop accepting input. To do this, we 1280 * disable the receive line status interrupts, and tell the 1281 * interrupt driver to stop checking the data ready bit in the 1282 * line status register. 1283 */ 1284 state->read_status_mask &= ~UART_LSR_DR; 1285 if (tty_port_initialized(port)) { 1286 /* disable receive interrupts */ 1287 custom.intena = IF_RBF; 1288 mb(); 1289 /* clear any pending receive interrupt */ 1290 custom.intreq = IF_RBF; 1291 mb(); 1292 1293 /* 1294 * Before we drop DTR, make sure the UART transmitter 1295 * has completely drained; this is especially 1296 * important if there is a transmit FIFO! 1297 */ 1298 rs_wait_until_sent(tty, state->timeout); 1299 } 1300 shutdown(tty, state); 1301 rs_flush_buffer(tty); 1302 1303 tty_ldisc_flush(tty); 1304 port->tty = NULL; 1305 1306 tty_port_close_end(port, tty); 1307 } 1308 1309 /* 1310 * rs_wait_until_sent() --- wait until the transmitter is empty 1311 */ 1312 static void rs_wait_until_sent(struct tty_struct *tty, int timeout) 1313 { 1314 struct serial_state *info = tty->driver_data; 1315 unsigned long orig_jiffies, char_time; 1316 int lsr; 1317 1318 if (info->xmit_fifo_size == 0) 1319 return; /* Just in case.... */ 1320 1321 orig_jiffies = jiffies; 1322 1323 /* 1324 * Set the check interval to be 1/5 of the estimated time to 1325 * send a single character, and make it at least 1. The check 1326 * interval should also be less than the timeout. 1327 * 1328 * Note: we have to use pretty tight timings here to satisfy 1329 * the NIST-PCTS. 1330 */ 1331 char_time = (info->timeout - HZ/50) / info->xmit_fifo_size; 1332 char_time = char_time / 5; 1333 if (char_time == 0) 1334 char_time = 1; 1335 if (timeout) 1336 char_time = min_t(unsigned long, char_time, timeout); 1337 /* 1338 * If the transmitter hasn't cleared in twice the approximate 1339 * amount of time to send the entire FIFO, it probably won't 1340 * ever clear. This assumes the UART isn't doing flow 1341 * control, which is currently the case. Hence, if it ever 1342 * takes longer than info->timeout, this is probably due to a 1343 * UART bug of some kind. So, we clamp the timeout parameter at 1344 * 2*info->timeout. 1345 */ 1346 if (!timeout || timeout > 2*info->timeout) 1347 timeout = 2*info->timeout; 1348 #ifdef SERIAL_DEBUG_RS_WAIT_UNTIL_SENT 1349 printk("In rs_wait_until_sent(%d) check=%lu...", timeout, char_time); 1350 printk("jiff=%lu...", jiffies); 1351 #endif 1352 while(!((lsr = custom.serdatr) & SDR_TSRE)) { 1353 #ifdef SERIAL_DEBUG_RS_WAIT_UNTIL_SENT 1354 printk("serdatr = %d (jiff=%lu)...", lsr, jiffies); 1355 #endif 1356 msleep_interruptible(jiffies_to_msecs(char_time)); 1357 if (signal_pending(current)) 1358 break; 1359 if (timeout && time_after(jiffies, orig_jiffies + timeout)) 1360 break; 1361 } 1362 __set_current_state(TASK_RUNNING); 1363 1364 #ifdef SERIAL_DEBUG_RS_WAIT_UNTIL_SENT 1365 printk("lsr = %d (jiff=%lu)...done\n", lsr, jiffies); 1366 #endif 1367 } 1368 1369 /* 1370 * rs_hangup() --- called by tty_hangup() when a hangup is signaled. 1371 */ 1372 static void rs_hangup(struct tty_struct *tty) 1373 { 1374 struct serial_state *info = tty->driver_data; 1375 1376 rs_flush_buffer(tty); 1377 shutdown(tty, info); 1378 info->tport.count = 0; 1379 tty_port_set_active(&info->tport, 0); 1380 info->tport.tty = NULL; 1381 wake_up_interruptible(&info->tport.open_wait); 1382 } 1383 1384 /* 1385 * This routine is called whenever a serial port is opened. It 1386 * enables interrupts for a serial port, linking in its async structure into 1387 * the IRQ chain. It also performs the serial-specific 1388 * initialization for the tty structure. 1389 */ 1390 static int rs_open(struct tty_struct *tty, struct file * filp) 1391 { 1392 struct serial_state *info = rs_table + tty->index; 1393 struct tty_port *port = &info->tport; 1394 int retval; 1395 1396 port->count++; 1397 port->tty = tty; 1398 tty->driver_data = info; 1399 tty->port = port; 1400 1401 retval = startup(tty, info); 1402 if (retval) { 1403 return retval; 1404 } 1405 1406 return tty_port_block_til_ready(port, tty, filp); 1407 } 1408 1409 /* 1410 * /proc fs routines.... 1411 */ 1412 1413 static inline void line_info(struct seq_file *m, int line, 1414 struct serial_state *state) 1415 { 1416 char stat_buf[30], control, status; 1417 unsigned long flags; 1418 1419 seq_printf(m, "%d: uart:amiga_builtin", line); 1420 1421 local_irq_save(flags); 1422 status = ciab.pra; 1423 control = tty_port_initialized(&state->tport) ? state->MCR : status; 1424 local_irq_restore(flags); 1425 1426 stat_buf[0] = 0; 1427 stat_buf[1] = 0; 1428 if(!(control & SER_RTS)) 1429 strcat(stat_buf, "|RTS"); 1430 if(!(status & SER_CTS)) 1431 strcat(stat_buf, "|CTS"); 1432 if(!(control & SER_DTR)) 1433 strcat(stat_buf, "|DTR"); 1434 if(!(status & SER_DSR)) 1435 strcat(stat_buf, "|DSR"); 1436 if(!(status & SER_DCD)) 1437 strcat(stat_buf, "|CD"); 1438 1439 if (state->quot) 1440 seq_printf(m, " baud:%d", state->baud_base / state->quot); 1441 1442 seq_printf(m, " tx:%d rx:%d", state->icount.tx, state->icount.rx); 1443 1444 if (state->icount.frame) 1445 seq_printf(m, " fe:%d", state->icount.frame); 1446 1447 if (state->icount.parity) 1448 seq_printf(m, " pe:%d", state->icount.parity); 1449 1450 if (state->icount.brk) 1451 seq_printf(m, " brk:%d", state->icount.brk); 1452 1453 if (state->icount.overrun) 1454 seq_printf(m, " oe:%d", state->icount.overrun); 1455 1456 /* 1457 * Last thing is the RS-232 status lines 1458 */ 1459 seq_printf(m, " %s\n", stat_buf+1); 1460 } 1461 1462 static int rs_proc_show(struct seq_file *m, void *v) 1463 { 1464 seq_printf(m, "serinfo:1.0 driver:%s\n", serial_version); 1465 line_info(m, 0, &rs_table[0]); 1466 return 0; 1467 } 1468 1469 /* 1470 * --------------------------------------------------------------------- 1471 * rs_init() and friends 1472 * 1473 * rs_init() is called at boot-time to initialize the serial driver. 1474 * --------------------------------------------------------------------- 1475 */ 1476 1477 /* 1478 * This routine prints out the appropriate serial driver version 1479 * number, and identifies which options were configured into this 1480 * driver. 1481 */ 1482 static void show_serial_version(void) 1483 { 1484 printk(KERN_INFO "%s version %s\n", serial_name, serial_version); 1485 } 1486 1487 1488 static const struct tty_operations serial_ops = { 1489 .open = rs_open, 1490 .close = rs_close, 1491 .write = rs_write, 1492 .put_char = rs_put_char, 1493 .flush_chars = rs_flush_chars, 1494 .write_room = rs_write_room, 1495 .chars_in_buffer = rs_chars_in_buffer, 1496 .flush_buffer = rs_flush_buffer, 1497 .ioctl = rs_ioctl, 1498 .throttle = rs_throttle, 1499 .unthrottle = rs_unthrottle, 1500 .set_termios = rs_set_termios, 1501 .stop = rs_stop, 1502 .start = rs_start, 1503 .hangup = rs_hangup, 1504 .break_ctl = rs_break, 1505 .send_xchar = rs_send_xchar, 1506 .wait_until_sent = rs_wait_until_sent, 1507 .tiocmget = rs_tiocmget, 1508 .tiocmset = rs_tiocmset, 1509 .get_icount = rs_get_icount, 1510 .set_serial = set_serial_info, 1511 .get_serial = get_serial_info, 1512 .proc_show = rs_proc_show, 1513 }; 1514 1515 static int amiga_carrier_raised(struct tty_port *port) 1516 { 1517 return !(ciab.pra & SER_DCD); 1518 } 1519 1520 static void amiga_dtr_rts(struct tty_port *port, int raise) 1521 { 1522 struct serial_state *info = container_of(port, struct serial_state, 1523 tport); 1524 unsigned long flags; 1525 1526 if (raise) 1527 info->MCR |= SER_DTR|SER_RTS; 1528 else 1529 info->MCR &= ~(SER_DTR|SER_RTS); 1530 1531 local_irq_save(flags); 1532 rtsdtr_ctrl(info->MCR); 1533 local_irq_restore(flags); 1534 } 1535 1536 static const struct tty_port_operations amiga_port_ops = { 1537 .carrier_raised = amiga_carrier_raised, 1538 .dtr_rts = amiga_dtr_rts, 1539 }; 1540 1541 /* 1542 * The serial driver boot-time initialization code! 1543 */ 1544 static int __init amiga_serial_probe(struct platform_device *pdev) 1545 { 1546 unsigned long flags; 1547 struct serial_state * state; 1548 int error; 1549 1550 serial_driver = alloc_tty_driver(NR_PORTS); 1551 if (!serial_driver) 1552 return -ENOMEM; 1553 1554 show_serial_version(); 1555 1556 /* Initialize the tty_driver structure */ 1557 1558 serial_driver->driver_name = "amiserial"; 1559 serial_driver->name = "ttyS"; 1560 serial_driver->major = TTY_MAJOR; 1561 serial_driver->minor_start = 64; 1562 serial_driver->type = TTY_DRIVER_TYPE_SERIAL; 1563 serial_driver->subtype = SERIAL_TYPE_NORMAL; 1564 serial_driver->init_termios = tty_std_termios; 1565 serial_driver->init_termios.c_cflag = 1566 B9600 | CS8 | CREAD | HUPCL | CLOCAL; 1567 serial_driver->flags = TTY_DRIVER_REAL_RAW; 1568 tty_set_operations(serial_driver, &serial_ops); 1569 1570 state = rs_table; 1571 state->port = (int)&custom.serdatr; /* Just to give it a value */ 1572 state->custom_divisor = 0; 1573 state->icount.cts = state->icount.dsr = 1574 state->icount.rng = state->icount.dcd = 0; 1575 state->icount.rx = state->icount.tx = 0; 1576 state->icount.frame = state->icount.parity = 0; 1577 state->icount.overrun = state->icount.brk = 0; 1578 tty_port_init(&state->tport); 1579 state->tport.ops = &amiga_port_ops; 1580 tty_port_link_device(&state->tport, serial_driver, 0); 1581 1582 error = tty_register_driver(serial_driver); 1583 if (error) 1584 goto fail_put_tty_driver; 1585 1586 printk(KERN_INFO "ttyS0 is the amiga builtin serial port\n"); 1587 1588 /* Hardware set up */ 1589 1590 state->baud_base = amiga_colorclock; 1591 state->xmit_fifo_size = 1; 1592 1593 /* set ISRs, and then disable the rx interrupts */ 1594 error = request_irq(IRQ_AMIGA_TBE, ser_tx_int, 0, "serial TX", state); 1595 if (error) 1596 goto fail_unregister; 1597 1598 error = request_irq(IRQ_AMIGA_RBF, ser_rx_int, 0, 1599 "serial RX", state); 1600 if (error) 1601 goto fail_free_irq; 1602 1603 local_irq_save(flags); 1604 1605 /* turn off Rx and Tx interrupts */ 1606 custom.intena = IF_RBF | IF_TBE; 1607 mb(); 1608 1609 /* clear any pending interrupt */ 1610 custom.intreq = IF_RBF | IF_TBE; 1611 mb(); 1612 1613 local_irq_restore(flags); 1614 1615 /* 1616 * set the appropriate directions for the modem control flags, 1617 * and clear RTS and DTR 1618 */ 1619 ciab.ddra |= (SER_DTR | SER_RTS); /* outputs */ 1620 ciab.ddra &= ~(SER_DCD | SER_CTS | SER_DSR); /* inputs */ 1621 1622 platform_set_drvdata(pdev, state); 1623 1624 return 0; 1625 1626 fail_free_irq: 1627 free_irq(IRQ_AMIGA_TBE, state); 1628 fail_unregister: 1629 tty_unregister_driver(serial_driver); 1630 fail_put_tty_driver: 1631 tty_port_destroy(&state->tport); 1632 put_tty_driver(serial_driver); 1633 return error; 1634 } 1635 1636 static int __exit amiga_serial_remove(struct platform_device *pdev) 1637 { 1638 struct serial_state *state = platform_get_drvdata(pdev); 1639 1640 /* printk("Unloading %s: version %s\n", serial_name, serial_version); */ 1641 tty_unregister_driver(serial_driver); 1642 put_tty_driver(serial_driver); 1643 tty_port_destroy(&state->tport); 1644 1645 free_irq(IRQ_AMIGA_TBE, state); 1646 free_irq(IRQ_AMIGA_RBF, state); 1647 1648 return 0; 1649 } 1650 1651 static struct platform_driver amiga_serial_driver = { 1652 .remove = __exit_p(amiga_serial_remove), 1653 .driver = { 1654 .name = "amiga-serial", 1655 }, 1656 }; 1657 1658 module_platform_driver_probe(amiga_serial_driver, amiga_serial_probe); 1659 1660 1661 #if defined(CONFIG_SERIAL_CONSOLE) && !defined(MODULE) 1662 1663 /* 1664 * ------------------------------------------------------------ 1665 * Serial console driver 1666 * ------------------------------------------------------------ 1667 */ 1668 1669 static void amiga_serial_putc(char c) 1670 { 1671 custom.serdat = (unsigned char)c | 0x100; 1672 while (!(custom.serdatr & 0x2000)) 1673 barrier(); 1674 } 1675 1676 /* 1677 * Print a string to the serial port trying not to disturb 1678 * any possible real use of the port... 1679 * 1680 * The console must be locked when we get here. 1681 */ 1682 static void serial_console_write(struct console *co, const char *s, 1683 unsigned count) 1684 { 1685 unsigned short intena = custom.intenar; 1686 1687 custom.intena = IF_TBE; 1688 1689 while (count--) { 1690 if (*s == '\n') 1691 amiga_serial_putc('\r'); 1692 amiga_serial_putc(*s++); 1693 } 1694 1695 custom.intena = IF_SETCLR | (intena & IF_TBE); 1696 } 1697 1698 static struct tty_driver *serial_console_device(struct console *c, int *index) 1699 { 1700 *index = 0; 1701 return serial_driver; 1702 } 1703 1704 static struct console sercons = { 1705 .name = "ttyS", 1706 .write = serial_console_write, 1707 .device = serial_console_device, 1708 .flags = CON_PRINTBUFFER, 1709 .index = -1, 1710 }; 1711 1712 /* 1713 * Register console. 1714 */ 1715 static int __init amiserial_console_init(void) 1716 { 1717 if (!MACH_IS_AMIGA) 1718 return -ENODEV; 1719 1720 register_console(&sercons); 1721 return 0; 1722 } 1723 console_initcall(amiserial_console_init); 1724 1725 #endif /* CONFIG_SERIAL_CONSOLE && !MODULE */ 1726 1727 MODULE_LICENSE("GPL"); 1728 MODULE_ALIAS("platform:amiga-serial"); 1729