1config TTY 2 bool "Enable TTY" if EXPERT 3 default y 4 ---help--- 5 Allows you to remove TTY support which can save space, and 6 blocks features that require TTY from inclusion in the kernel. 7 TTY is required for any text terminals or serial port 8 communication. Most users should leave this enabled. 9 10if TTY 11 12config VT 13 bool "Virtual terminal" if EXPERT 14 depends on !S390 && !UML 15 select INPUT 16 default y 17 ---help--- 18 If you say Y here, you will get support for terminal devices with 19 display and keyboard devices. These are called "virtual" because you 20 can run several virtual terminals (also called virtual consoles) on 21 one physical terminal. This is rather useful, for example one 22 virtual terminal can collect system messages and warnings, another 23 one can be used for a text-mode user session, and a third could run 24 an X session, all in parallel. Switching between virtual terminals 25 is done with certain key combinations, usually Alt-<function key>. 26 27 The setterm command ("man setterm") can be used to change the 28 properties (such as colors or beeping) of a virtual terminal. The 29 man page console_codes(4) ("man console_codes") contains the special 30 character sequences that can be used to change those properties 31 directly. The fonts used on virtual terminals can be changed with 32 the setfont ("man setfont") command and the key bindings are defined 33 with the loadkeys ("man loadkeys") command. 34 35 You need at least one virtual terminal device in order to make use 36 of your keyboard and monitor. Therefore, only people configuring an 37 embedded system would want to say N here in order to save some 38 memory; the only way to log into such a system is then via a serial 39 or network connection. 40 41 If unsure, say Y, or else you won't be able to do much with your new 42 shiny Linux system :-) 43 44config CONSOLE_TRANSLATIONS 45 depends on VT 46 default y 47 bool "Enable character translations in console" if EXPERT 48 ---help--- 49 This enables support for font mapping and Unicode translation 50 on virtual consoles. 51 52config VT_CONSOLE 53 bool "Support for console on virtual terminal" if EXPERT 54 depends on VT 55 default y 56 ---help--- 57 The system console is the device which receives all kernel messages 58 and warnings and which allows logins in single user mode. If you 59 answer Y here, a virtual terminal (the device used to interact with 60 a physical terminal) can be used as system console. This is the most 61 common mode of operations, so you should say Y here unless you want 62 the kernel messages be output only to a serial port (in which case 63 you should say Y to "Console on serial port", below). 64 65 If you do say Y here, by default the currently visible virtual 66 terminal (/dev/tty0) will be used as system console. You can change 67 that with a kernel command line option such as "console=tty3" which 68 would use the third virtual terminal as system console. (Try "man 69 bootparam" or see the documentation of your boot loader (lilo or 70 loadlin) about how to pass options to the kernel at boot time.) 71 72 If unsure, say Y. 73 74config VT_CONSOLE_SLEEP 75 def_bool y 76 depends on VT_CONSOLE && PM_SLEEP 77 78config HW_CONSOLE 79 bool 80 depends on VT && !UML 81 default y 82 83config VT_HW_CONSOLE_BINDING 84 bool "Support for binding and unbinding console drivers" 85 depends on HW_CONSOLE 86 default n 87 ---help--- 88 The virtual terminal is the device that interacts with the physical 89 terminal through console drivers. On these systems, at least one 90 console driver is loaded. In other configurations, additional console 91 drivers may be enabled, such as the framebuffer console. If more than 92 1 console driver is enabled, setting this to 'y' will allow you to 93 select the console driver that will serve as the backend for the 94 virtual terminals. 95 96 See <file:Documentation/console/console.txt> for more 97 information. For framebuffer console users, please refer to 98 <file:Documentation/fb/fbcon.txt>. 99 100config UNIX98_PTYS 101 bool "Unix98 PTY support" if EXPERT 102 default y 103 ---help--- 104 A pseudo terminal (PTY) is a software device consisting of two 105 halves: a master and a slave. The slave device behaves identical to 106 a physical terminal; the master device is used by a process to 107 read data from and write data to the slave, thereby emulating a 108 terminal. Typical programs for the master side are telnet servers 109 and xterms. 110 111 Linux has traditionally used the BSD-like names /dev/ptyxx for 112 masters and /dev/ttyxx for slaves of pseudo terminals. This scheme 113 has a number of problems. The GNU C library glibc 2.1 and later, 114 however, supports the Unix98 naming standard: in order to acquire a 115 pseudo terminal, a process opens /dev/ptmx; the number of the pseudo 116 terminal is then made available to the process and the pseudo 117 terminal slave can be accessed as /dev/pts/<number>. What was 118 traditionally /dev/ttyp2 will then be /dev/pts/2, for example. 119 120 All modern Linux systems use the Unix98 ptys. Say Y unless 121 you're on an embedded system and want to conserve memory. 122 123config DEVPTS_MULTIPLE_INSTANCES 124 bool "Support multiple instances of devpts" 125 depends on UNIX98_PTYS 126 default n 127 ---help--- 128 Enable support for multiple instances of devpts filesystem. 129 If you want to have isolated PTY namespaces (eg: in containers), 130 say Y here. Otherwise, say N. If enabled, each mount of devpts 131 filesystem with the '-o newinstance' option will create an 132 independent PTY namespace. 133 134config LEGACY_PTYS 135 bool "Legacy (BSD) PTY support" 136 default y 137 ---help--- 138 A pseudo terminal (PTY) is a software device consisting of two 139 halves: a master and a slave. The slave device behaves identical to 140 a physical terminal; the master device is used by a process to 141 read data from and write data to the slave, thereby emulating a 142 terminal. Typical programs for the master side are telnet servers 143 and xterms. 144 145 Linux has traditionally used the BSD-like names /dev/ptyxx 146 for masters and /dev/ttyxx for slaves of pseudo 147 terminals. This scheme has a number of problems, including 148 security. This option enables these legacy devices; on most 149 systems, it is safe to say N. 150 151 152config LEGACY_PTY_COUNT 153 int "Maximum number of legacy PTY in use" 154 depends on LEGACY_PTYS 155 range 0 256 156 default "256" 157 ---help--- 158 The maximum number of legacy PTYs that can be used at any one time. 159 The default is 256, and should be more than enough. Embedded 160 systems may want to reduce this to save memory. 161 162 When not in use, each legacy PTY occupies 12 bytes on 32-bit 163 architectures and 24 bytes on 64-bit architectures. 164 165config BFIN_JTAG_COMM 166 tristate "Blackfin JTAG Communication" 167 depends on BLACKFIN 168 help 169 Add support for emulating a TTY device over the Blackfin JTAG. 170 171 To compile this driver as a module, choose M here: the 172 module will be called bfin_jtag_comm. 173 174config BFIN_JTAG_COMM_CONSOLE 175 bool "Console on Blackfin JTAG" 176 depends on BFIN_JTAG_COMM=y 177 178config SERIAL_NONSTANDARD 179 bool "Non-standard serial port support" 180 depends on HAS_IOMEM 181 ---help--- 182 Say Y here if you have any non-standard serial boards -- boards 183 which aren't supported using the standard "dumb" serial driver. 184 This includes intelligent serial boards such as Cyclades, 185 Digiboards, etc. These are usually used for systems that need many 186 serial ports because they serve many terminals or dial-in 187 connections. 188 189 Note that the answer to this question won't directly affect the 190 kernel: saying N will just cause the configurator to skip all 191 the questions about non-standard serial boards. 192 193 Most people can say N here. 194 195config ROCKETPORT 196 tristate "Comtrol RocketPort support" 197 depends on SERIAL_NONSTANDARD && (ISA || EISA || PCI) 198 help 199 This driver supports Comtrol RocketPort and RocketModem PCI boards. 200 These boards provide 2, 4, 8, 16, or 32 high-speed serial ports or 201 modems. For information about the RocketPort/RocketModem boards 202 and this driver read <file:Documentation/serial/rocket.txt>. 203 204 To compile this driver as a module, choose M here: the 205 module will be called rocket. 206 207 If you want to compile this driver into the kernel, say Y here. If 208 you don't have a Comtrol RocketPort/RocketModem card installed, say N. 209 210config CYCLADES 211 tristate "Cyclades async mux support" 212 depends on SERIAL_NONSTANDARD && (PCI || ISA) 213 select FW_LOADER 214 ---help--- 215 This driver supports Cyclades Z and Y multiserial boards. 216 You would need something like this to connect more than two modems to 217 your Linux box, for instance in order to become a dial-in server. 218 219 For information about the Cyclades-Z card, read 220 <file:Documentation/serial/README.cycladesZ>. 221 222 To compile this driver as a module, choose M here: the 223 module will be called cyclades. 224 225 If you haven't heard about it, it's safe to say N. 226 227config CYZ_INTR 228 bool "Cyclades-Z interrupt mode operation" 229 depends on CYCLADES 230 help 231 The Cyclades-Z family of multiport cards allows 2 (two) driver op 232 modes: polling and interrupt. In polling mode, the driver will check 233 the status of the Cyclades-Z ports every certain amount of time 234 (which is called polling cycle and is configurable). In interrupt 235 mode, it will use an interrupt line (IRQ) in order to check the 236 status of the Cyclades-Z ports. The default op mode is polling. If 237 unsure, say N. 238 239config MOXA_INTELLIO 240 tristate "Moxa Intellio support" 241 depends on SERIAL_NONSTANDARD && (ISA || EISA || PCI) 242 select FW_LOADER 243 help 244 Say Y here if you have a Moxa Intellio multiport serial card. 245 246 To compile this driver as a module, choose M here: the 247 module will be called moxa. 248 249config MOXA_SMARTIO 250 tristate "Moxa SmartIO support v. 2.0" 251 depends on SERIAL_NONSTANDARD && (PCI || EISA || ISA) 252 help 253 Say Y here if you have a Moxa SmartIO multiport serial card and/or 254 want to help develop a new version of this driver. 255 256 This is upgraded (1.9.1) driver from original Moxa drivers with 257 changes finally resulting in PCI probing. 258 259 This driver can also be built as a module. The module will be called 260 mxser. If you want to do that, say M here. 261 262config SYNCLINK 263 tristate "Microgate SyncLink card support" 264 depends on SERIAL_NONSTANDARD && PCI && ISA_DMA_API 265 help 266 Provides support for the SyncLink ISA and PCI multiprotocol serial 267 adapters. These adapters support asynchronous and HDLC bit 268 synchronous communication up to 10Mbps (PCI adapter). 269 270 This driver can only be built as a module ( = code which can be 271 inserted in and removed from the running kernel whenever you want). 272 The module will be called synclink. If you want to do that, say M 273 here. 274 275config SYNCLINKMP 276 tristate "SyncLink Multiport support" 277 depends on SERIAL_NONSTANDARD && PCI 278 help 279 Enable support for the SyncLink Multiport (2 or 4 ports) 280 serial adapter, running asynchronous and HDLC communications up 281 to 2.048Mbps. Each ports is independently selectable for 282 RS-232, V.35, RS-449, RS-530, and X.21 283 284 This driver may be built as a module ( = code which can be 285 inserted in and removed from the running kernel whenever you want). 286 The module will be called synclinkmp. If you want to do that, say M 287 here. 288 289config SYNCLINK_GT 290 tristate "SyncLink GT/AC support" 291 depends on SERIAL_NONSTANDARD && PCI 292 help 293 Support for SyncLink GT and SyncLink AC families of 294 synchronous and asynchronous serial adapters 295 manufactured by Microgate Systems, Ltd. (www.microgate.com) 296 297config NOZOMI 298 tristate "HSDPA Broadband Wireless Data Card - Globe Trotter" 299 depends on PCI 300 help 301 If you have a HSDPA driver Broadband Wireless Data Card - 302 Globe Trotter PCMCIA card, say Y here. 303 304 To compile this driver as a module, choose M here, the module 305 will be called nozomi. 306 307config ISI 308 tristate "Multi-Tech multiport card support" 309 depends on SERIAL_NONSTANDARD && PCI 310 select FW_LOADER 311 help 312 This is a driver for the Multi-Tech cards which provide several 313 serial ports. The driver is experimental and can currently only be 314 built as a module. The module will be called isicom. 315 If you want to do that, choose M here. 316 317config N_HDLC 318 tristate "HDLC line discipline support" 319 depends on SERIAL_NONSTANDARD 320 help 321 Allows synchronous HDLC communications with tty device drivers that 322 support synchronous HDLC such as the Microgate SyncLink adapter. 323 324 This driver can be built as a module ( = code which can be 325 inserted in and removed from the running kernel whenever you want). 326 The module will be called n_hdlc. If you want to do that, say M 327 here. 328 329config N_GSM 330 tristate "GSM MUX line discipline support (EXPERIMENTAL)" 331 depends on NET 332 help 333 This line discipline provides support for the GSM MUX protocol and 334 presents the mux as a set of 61 individual tty devices. 335 336config TRACE_ROUTER 337 tristate "Trace data router for MIPI P1149.7 cJTAG standard" 338 depends on TRACE_SINK 339 default n 340 help 341 The trace router uses the Linux tty line discipline framework to 342 route trace data coming from a tty port (say UART for example) to 343 the trace sink line discipline driver and to another tty port (say 344 USB). This is part of a solution for the MIPI P1149.7, compact JTAG, 345 standard, which is for debugging mobile devices. The PTI driver in 346 drivers/misc/pti.c defines the majority of this MIPI solution. 347 348 You should select this driver if the target kernel is meant for 349 a mobile device containing a modem. Then you will need to select 350 "Trace data sink for MIPI P1149.7 cJTAG standard" line discipline 351 driver. 352 353config TRACE_SINK 354 tristate "Trace data sink for MIPI P1149.7 cJTAG standard" 355 default n 356 help 357 The trace sink uses the Linux line discipline framework to receive 358 trace data coming from the trace router line discipline driver 359 to a user-defined tty port target, like USB. 360 This is to provide a way to extract modem trace data on 361 devices that do not have a PTI HW module, or just need modem 362 trace data to come out of a different HW output port. 363 This is part of a solution for the P1149.7, compact JTAG, standard. 364 365 If you select this option, you need to select 366 "Trace data router for MIPI P1149.7 cJTAG standard". 367 368config PPC_EPAPR_HV_BYTECHAN 369 bool "ePAPR hypervisor byte channel driver" 370 depends on PPC 371 select EPAPR_PARAVIRT 372 help 373 This driver creates /dev entries for each ePAPR hypervisor byte 374 channel, thereby allowing applications to communicate with byte 375 channels as if they were serial ports. 376 377config PPC_EARLY_DEBUG_EHV_BC 378 bool "Early console (udbg) support for ePAPR hypervisors" 379 depends on PPC_EPAPR_HV_BYTECHAN=y 380 help 381 Select this option to enable early console (a.k.a. "udbg") support 382 via an ePAPR byte channel. You also need to choose the byte channel 383 handle below. 384 385config PPC_EARLY_DEBUG_EHV_BC_HANDLE 386 int "Byte channel handle for early console (udbg)" 387 depends on PPC_EARLY_DEBUG_EHV_BC 388 default 0 389 help 390 If you want early console (udbg) output through a byte channel, 391 specify the handle of the byte channel to use. 392 393 For this to work, the byte channel driver must be compiled 394 in-kernel, not as a module. 395 396 Note that only one early console driver can be enabled, so don't 397 enable any others if you enable this one. 398 399 If the number you specify is not a valid byte channel handle, then 400 there simply will be no early console output. This is true also 401 if you don't boot under a hypervisor at all. 402 403config GOLDFISH_TTY 404 tristate "Goldfish TTY Driver" 405 depends on GOLDFISH 406 help 407 Console and system TTY driver for the Goldfish virtual platform. 408 409config DA_TTY 410 bool "DA TTY" 411 depends on METAG_DA 412 select SERIAL_NONSTANDARD 413 help 414 This enables a TTY on a Dash channel. 415 416config DA_CONSOLE 417 bool "DA Console" 418 depends on DA_TTY 419 help 420 This enables a console on a Dash channel. 421 422config MIPS_EJTAG_FDC_TTY 423 bool "MIPS EJTAG Fast Debug Channel TTY" 424 depends on MIPS_CDMM 425 help 426 This enables a TTY and console on the MIPS EJTAG Fast Debug Channels, 427 if they are present. This can be useful when working with an EJTAG 428 probe which supports it, to get console output and a login prompt via 429 EJTAG without needing to connect a serial cable. 430 431 TTY devices are named e.g. ttyFDC3c2 (for FDC channel 2 of the FDC on 432 CPU3). 433 434 The console can be enabled with console=fdc1 (for FDC channel 1 on all 435 CPUs). Do not use the console unless there is a debug probe attached 436 to drain the FDC TX FIFO. 437 438 If unsure, say N. 439 440config MIPS_EJTAG_FDC_EARLYCON 441 bool "Early FDC console" 442 depends on MIPS_EJTAG_FDC_TTY 443 help 444 This registers a console on FDC channel 1 very early during boot (from 445 MIPS arch code). This is useful for bring-up and debugging early boot 446 issues. 447 448 Do not enable unless there is a debug probe attached to drain the FDC 449 TX FIFO. 450 451 If unsure, say N. 452 453config MIPS_EJTAG_FDC_KGDB 454 bool "Use KGDB over an FDC channel" 455 depends on MIPS_EJTAG_FDC_TTY && KGDB 456 default y 457 help 458 This enables the use of KGDB over an FDC channel, allowing KGDB to be 459 used remotely or when a serial port isn't available. 460 461config MIPS_EJTAG_FDC_KGDB_CHAN 462 int "KGDB FDC channel" 463 depends on MIPS_EJTAG_FDC_KGDB 464 range 2 15 465 default 3 466 help 467 FDC channel number to use for KGDB. 468 469endif # TTY 470