1config VT 2 bool "Virtual terminal" if EXPERT 3 depends on !S390 && !UML 4 select INPUT 5 default y 6 ---help--- 7 If you say Y here, you will get support for terminal devices with 8 display and keyboard devices. These are called "virtual" because you 9 can run several virtual terminals (also called virtual consoles) on 10 one physical terminal. This is rather useful, for example one 11 virtual terminal can collect system messages and warnings, another 12 one can be used for a text-mode user session, and a third could run 13 an X session, all in parallel. Switching between virtual terminals 14 is done with certain key combinations, usually Alt-<function key>. 15 16 The setterm command ("man setterm") can be used to change the 17 properties (such as colors or beeping) of a virtual terminal. The 18 man page console_codes(4) ("man console_codes") contains the special 19 character sequences that can be used to change those properties 20 directly. The fonts used on virtual terminals can be changed with 21 the setfont ("man setfont") command and the key bindings are defined 22 with the loadkeys ("man loadkeys") command. 23 24 You need at least one virtual terminal device in order to make use 25 of your keyboard and monitor. Therefore, only people configuring an 26 embedded system would want to say N here in order to save some 27 memory; the only way to log into such a system is then via a serial 28 or network connection. 29 30 If unsure, say Y, or else you won't be able to do much with your new 31 shiny Linux system :-) 32 33config CONSOLE_TRANSLATIONS 34 depends on VT 35 default y 36 bool "Enable character translations in console" if EXPERT 37 ---help--- 38 This enables support for font mapping and Unicode translation 39 on virtual consoles. 40 41config VT_CONSOLE 42 bool "Support for console on virtual terminal" if EXPERT 43 depends on VT 44 default y 45 ---help--- 46 The system console is the device which receives all kernel messages 47 and warnings and which allows logins in single user mode. If you 48 answer Y here, a virtual terminal (the device used to interact with 49 a physical terminal) can be used as system console. This is the most 50 common mode of operations, so you should say Y here unless you want 51 the kernel messages be output only to a serial port (in which case 52 you should say Y to "Console on serial port", below). 53 54 If you do say Y here, by default the currently visible virtual 55 terminal (/dev/tty0) will be used as system console. You can change 56 that with a kernel command line option such as "console=tty3" which 57 would use the third virtual terminal as system console. (Try "man 58 bootparam" or see the documentation of your boot loader (lilo or 59 loadlin) about how to pass options to the kernel at boot time.) 60 61 If unsure, say Y. 62 63config VT_CONSOLE_SLEEP 64 def_bool y 65 depends on VT_CONSOLE && PM_SLEEP 66 67config HW_CONSOLE 68 bool 69 depends on VT && !UML 70 default y 71 72config VT_HW_CONSOLE_BINDING 73 bool "Support for binding and unbinding console drivers" 74 depends on HW_CONSOLE 75 default n 76 ---help--- 77 The virtual terminal is the device that interacts with the physical 78 terminal through console drivers. On these systems, at least one 79 console driver is loaded. In other configurations, additional console 80 drivers may be enabled, such as the framebuffer console. If more than 81 1 console driver is enabled, setting this to 'y' will allow you to 82 select the console driver that will serve as the backend for the 83 virtual terminals. 84 85 See <file:Documentation/console/console.txt> for more 86 information. For framebuffer console users, please refer to 87 <file:Documentation/fb/fbcon.txt>. 88 89config UNIX98_PTYS 90 bool "Unix98 PTY support" if EXPERT 91 default y 92 ---help--- 93 A pseudo terminal (PTY) is a software device consisting of two 94 halves: a master and a slave. The slave device behaves identical to 95 a physical terminal; the master device is used by a process to 96 read data from and write data to the slave, thereby emulating a 97 terminal. Typical programs for the master side are telnet servers 98 and xterms. 99 100 Linux has traditionally used the BSD-like names /dev/ptyxx for 101 masters and /dev/ttyxx for slaves of pseudo terminals. This scheme 102 has a number of problems. The GNU C library glibc 2.1 and later, 103 however, supports the Unix98 naming standard: in order to acquire a 104 pseudo terminal, a process opens /dev/ptmx; the number of the pseudo 105 terminal is then made available to the process and the pseudo 106 terminal slave can be accessed as /dev/pts/<number>. What was 107 traditionally /dev/ttyp2 will then be /dev/pts/2, for example. 108 109 All modern Linux systems use the Unix98 ptys. Say Y unless 110 you're on an embedded system and want to conserve memory. 111 112config DEVPTS_MULTIPLE_INSTANCES 113 bool "Support multiple instances of devpts" 114 depends on UNIX98_PTYS 115 default n 116 ---help--- 117 Enable support for multiple instances of devpts filesystem. 118 If you want to have isolated PTY namespaces (eg: in containers), 119 say Y here. Otherwise, say N. If enabled, each mount of devpts 120 filesystem with the '-o newinstance' option will create an 121 independent PTY namespace. 122 123config LEGACY_PTYS 124 bool "Legacy (BSD) PTY support" 125 default y 126 ---help--- 127 A pseudo terminal (PTY) is a software device consisting of two 128 halves: a master and a slave. The slave device behaves identical to 129 a physical terminal; the master device is used by a process to 130 read data from and write data to the slave, thereby emulating a 131 terminal. Typical programs for the master side are telnet servers 132 and xterms. 133 134 Linux has traditionally used the BSD-like names /dev/ptyxx 135 for masters and /dev/ttyxx for slaves of pseudo 136 terminals. This scheme has a number of problems, including 137 security. This option enables these legacy devices; on most 138 systems, it is safe to say N. 139 140 141config LEGACY_PTY_COUNT 142 int "Maximum number of legacy PTY in use" 143 depends on LEGACY_PTYS 144 range 0 256 145 default "256" 146 ---help--- 147 The maximum number of legacy PTYs that can be used at any one time. 148 The default is 256, and should be more than enough. Embedded 149 systems may want to reduce this to save memory. 150 151 When not in use, each legacy PTY occupies 12 bytes on 32-bit 152 architectures and 24 bytes on 64-bit architectures. 153 154config BFIN_JTAG_COMM 155 tristate "Blackfin JTAG Communication" 156 depends on BLACKFIN 157 help 158 Add support for emulating a TTY device over the Blackfin JTAG. 159 160 To compile this driver as a module, choose M here: the 161 module will be called bfin_jtag_comm. 162 163config BFIN_JTAG_COMM_CONSOLE 164 bool "Console on Blackfin JTAG" 165 depends on BFIN_JTAG_COMM=y 166 167config SERIAL_NONSTANDARD 168 bool "Non-standard serial port support" 169 depends on HAS_IOMEM 170 ---help--- 171 Say Y here if you have any non-standard serial boards -- boards 172 which aren't supported using the standard "dumb" serial driver. 173 This includes intelligent serial boards such as Cyclades, 174 Digiboards, etc. These are usually used for systems that need many 175 serial ports because they serve many terminals or dial-in 176 connections. 177 178 Note that the answer to this question won't directly affect the 179 kernel: saying N will just cause the configurator to skip all 180 the questions about non-standard serial boards. 181 182 Most people can say N here. 183 184config ROCKETPORT 185 tristate "Comtrol RocketPort support" 186 depends on SERIAL_NONSTANDARD && (ISA || EISA || PCI) 187 help 188 This driver supports Comtrol RocketPort and RocketModem PCI boards. 189 These boards provide 2, 4, 8, 16, or 32 high-speed serial ports or 190 modems. For information about the RocketPort/RocketModem boards 191 and this driver read <file:Documentation/serial/rocket.txt>. 192 193 To compile this driver as a module, choose M here: the 194 module will be called rocket. 195 196 If you want to compile this driver into the kernel, say Y here. If 197 you don't have a Comtrol RocketPort/RocketModem card installed, say N. 198 199config CYCLADES 200 tristate "Cyclades async mux support" 201 depends on SERIAL_NONSTANDARD && (PCI || ISA) 202 select FW_LOADER 203 ---help--- 204 This driver supports Cyclades Z and Y multiserial boards. 205 You would need something like this to connect more than two modems to 206 your Linux box, for instance in order to become a dial-in server. 207 208 For information about the Cyclades-Z card, read 209 <file:Documentation/serial/README.cycladesZ>. 210 211 To compile this driver as a module, choose M here: the 212 module will be called cyclades. 213 214 If you haven't heard about it, it's safe to say N. 215 216config CYZ_INTR 217 bool "Cyclades-Z interrupt mode operation (EXPERIMENTAL)" 218 depends on EXPERIMENTAL && CYCLADES 219 help 220 The Cyclades-Z family of multiport cards allows 2 (two) driver op 221 modes: polling and interrupt. In polling mode, the driver will check 222 the status of the Cyclades-Z ports every certain amount of time 223 (which is called polling cycle and is configurable). In interrupt 224 mode, it will use an interrupt line (IRQ) in order to check the 225 status of the Cyclades-Z ports. The default op mode is polling. If 226 unsure, say N. 227 228config MOXA_INTELLIO 229 tristate "Moxa Intellio support" 230 depends on SERIAL_NONSTANDARD && (ISA || EISA || PCI) 231 select FW_LOADER 232 help 233 Say Y here if you have a Moxa Intellio multiport serial card. 234 235 To compile this driver as a module, choose M here: the 236 module will be called moxa. 237 238config MOXA_SMARTIO 239 tristate "Moxa SmartIO support v. 2.0" 240 depends on SERIAL_NONSTANDARD && (PCI || EISA || ISA) 241 help 242 Say Y here if you have a Moxa SmartIO multiport serial card and/or 243 want to help develop a new version of this driver. 244 245 This is upgraded (1.9.1) driver from original Moxa drivers with 246 changes finally resulting in PCI probing. 247 248 This driver can also be built as a module. The module will be called 249 mxser. If you want to do that, say M here. 250 251config SYNCLINK 252 tristate "Microgate SyncLink card support" 253 depends on SERIAL_NONSTANDARD && PCI && ISA_DMA_API 254 help 255 Provides support for the SyncLink ISA and PCI multiprotocol serial 256 adapters. These adapters support asynchronous and HDLC bit 257 synchronous communication up to 10Mbps (PCI adapter). 258 259 This driver can only be built as a module ( = code which can be 260 inserted in and removed from the running kernel whenever you want). 261 The module will be called synclink. If you want to do that, say M 262 here. 263 264config SYNCLINKMP 265 tristate "SyncLink Multiport support" 266 depends on SERIAL_NONSTANDARD && PCI 267 help 268 Enable support for the SyncLink Multiport (2 or 4 ports) 269 serial adapter, running asynchronous and HDLC communications up 270 to 2.048Mbps. Each ports is independently selectable for 271 RS-232, V.35, RS-449, RS-530, and X.21 272 273 This driver may be built as a module ( = code which can be 274 inserted in and removed from the running kernel whenever you want). 275 The module will be called synclinkmp. If you want to do that, say M 276 here. 277 278config SYNCLINK_GT 279 tristate "SyncLink GT/AC support" 280 depends on SERIAL_NONSTANDARD && PCI 281 help 282 Support for SyncLink GT and SyncLink AC families of 283 synchronous and asynchronous serial adapters 284 manufactured by Microgate Systems, Ltd. (www.microgate.com) 285 286config NOZOMI 287 tristate "HSDPA Broadband Wireless Data Card - Globe Trotter" 288 depends on PCI && EXPERIMENTAL 289 help 290 If you have a HSDPA driver Broadband Wireless Data Card - 291 Globe Trotter PCMCIA card, say Y here. 292 293 To compile this driver as a module, choose M here, the module 294 will be called nozomi. 295 296config ISI 297 tristate "Multi-Tech multiport card support (EXPERIMENTAL)" 298 depends on SERIAL_NONSTANDARD && PCI 299 select FW_LOADER 300 help 301 This is a driver for the Multi-Tech cards which provide several 302 serial ports. The driver is experimental and can currently only be 303 built as a module. The module will be called isicom. 304 If you want to do that, choose M here. 305 306config N_HDLC 307 tristate "HDLC line discipline support" 308 depends on SERIAL_NONSTANDARD 309 help 310 Allows synchronous HDLC communications with tty device drivers that 311 support synchronous HDLC such as the Microgate SyncLink adapter. 312 313 This driver can be built as a module ( = code which can be 314 inserted in and removed from the running kernel whenever you want). 315 The module will be called n_hdlc. If you want to do that, say M 316 here. 317 318config N_GSM 319 tristate "GSM MUX line discipline support (EXPERIMENTAL)" 320 depends on EXPERIMENTAL 321 depends on NET 322 help 323 This line discipline provides support for the GSM MUX protocol and 324 presents the mux as a set of 61 individual tty devices. 325 326config TRACE_ROUTER 327 tristate "Trace data router for MIPI P1149.7 cJTAG standard" 328 depends on TRACE_SINK 329 default n 330 help 331 The trace router uses the Linux tty line discipline framework to 332 route trace data coming from a tty port (say UART for example) to 333 the trace sink line discipline driver and to another tty port (say 334 USB). This is part of a solution for the MIPI P1149.7, compact JTAG, 335 standard, which is for debugging mobile devices. The PTI driver in 336 drivers/misc/pti.c defines the majority of this MIPI solution. 337 338 You should select this driver if the target kernel is meant for 339 a mobile device containing a modem. Then you will need to select 340 "Trace data sink for MIPI P1149.7 cJTAG standard" line discipline 341 driver. 342 343config TRACE_SINK 344 tristate "Trace data sink for MIPI P1149.7 cJTAG standard" 345 default n 346 help 347 The trace sink uses the Linux line discipline framework to receive 348 trace data coming from the trace router line discipline driver 349 to a user-defined tty port target, like USB. 350 This is to provide a way to extract modem trace data on 351 devices that do not have a PTI HW module, or just need modem 352 trace data to come out of a different HW output port. 353 This is part of a solution for the P1149.7, compact JTAG, standard. 354 355 If you select this option, you need to select 356 "Trace data router for MIPI P1149.7 cJTAG standard". 357 358config PPC_EPAPR_HV_BYTECHAN 359 tristate "ePAPR hypervisor byte channel driver" 360 depends on PPC 361 help 362 This driver creates /dev entries for each ePAPR hypervisor byte 363 channel, thereby allowing applications to communicate with byte 364 channels as if they were serial ports. 365 366config PPC_EARLY_DEBUG_EHV_BC 367 bool "Early console (udbg) support for ePAPR hypervisors" 368 depends on PPC_EPAPR_HV_BYTECHAN=y 369 help 370 Select this option to enable early console (a.k.a. "udbg") support 371 via an ePAPR byte channel. You also need to choose the byte channel 372 handle below. 373 374config PPC_EARLY_DEBUG_EHV_BC_HANDLE 375 int "Byte channel handle for early console (udbg)" 376 depends on PPC_EARLY_DEBUG_EHV_BC 377 default 0 378 help 379 If you want early console (udbg) output through a byte channel, 380 specify the handle of the byte channel to use. 381 382 For this to work, the byte channel driver must be compiled 383 in-kernel, not as a module. 384 385 Note that only one early console driver can be enabled, so don't 386 enable any others if you enable this one. 387 388 If the number you specify is not a valid byte channel handle, then 389 there simply will be no early console output. This is true also 390 if you don't boot under a hypervisor at all. 391