1 /* 2 * Copyright (c) 2014-2016, Fuzhou Rockchip Electronics Co., Ltd 3 * Caesar Wang <wxt@rock-chips.com> 4 * 5 * This program is free software; you can redistribute it and/or modify it 6 * under the terms and conditions of the GNU General Public License, 7 * version 2, as published by the Free Software Foundation. 8 * 9 * This program is distributed in the hope it will be useful, but WITHOUT 10 * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or 11 * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for 12 * more details. 13 */ 14 15 #include <linux/clk.h> 16 #include <linux/delay.h> 17 #include <linux/interrupt.h> 18 #include <linux/io.h> 19 #include <linux/module.h> 20 #include <linux/of.h> 21 #include <linux/of_address.h> 22 #include <linux/of_irq.h> 23 #include <linux/platform_device.h> 24 #include <linux/regmap.h> 25 #include <linux/reset.h> 26 #include <linux/thermal.h> 27 #include <linux/mfd/syscon.h> 28 #include <linux/pinctrl/consumer.h> 29 30 /** 31 * If the temperature over a period of time High, 32 * the resulting TSHUT gave CRU module,let it reset the entire chip, 33 * or via GPIO give PMIC. 34 */ 35 enum tshut_mode { 36 TSHUT_MODE_CRU = 0, 37 TSHUT_MODE_GPIO, 38 }; 39 40 /** 41 * The system Temperature Sensors tshut(tshut) polarity 42 * the bit 8 is tshut polarity. 43 * 0: low active, 1: high active 44 */ 45 enum tshut_polarity { 46 TSHUT_LOW_ACTIVE = 0, 47 TSHUT_HIGH_ACTIVE, 48 }; 49 50 /** 51 * The system has two Temperature Sensors. 52 * sensor0 is for CPU, and sensor1 is for GPU. 53 */ 54 enum sensor_id { 55 SENSOR_CPU = 0, 56 SENSOR_GPU, 57 }; 58 59 /** 60 * The conversion table has the adc value and temperature. 61 * ADC_DECREMENT: the adc value is of diminishing.(e.g. rk3288_code_table) 62 * ADC_INCREMENT: the adc value is incremental.(e.g. rk3368_code_table) 63 */ 64 enum adc_sort_mode { 65 ADC_DECREMENT = 0, 66 ADC_INCREMENT, 67 }; 68 69 /** 70 * The max sensors is two in rockchip SoCs. 71 * Two sensors: CPU and GPU sensor. 72 */ 73 #define SOC_MAX_SENSORS 2 74 75 /** 76 * struct chip_tsadc_table - hold information about chip-specific differences 77 * @id: conversion table 78 * @length: size of conversion table 79 * @data_mask: mask to apply on data inputs 80 * @mode: sort mode of this adc variant (incrementing or decrementing) 81 */ 82 struct chip_tsadc_table { 83 const struct tsadc_table *id; 84 unsigned int length; 85 u32 data_mask; 86 enum adc_sort_mode mode; 87 }; 88 89 /** 90 * struct rockchip_tsadc_chip - hold the private data of tsadc chip 91 * @chn_id[SOC_MAX_SENSORS]: the sensor id of chip correspond to the channel 92 * @chn_num: the channel number of tsadc chip 93 * @tshut_temp: the hardware-controlled shutdown temperature value 94 * @tshut_mode: the hardware-controlled shutdown mode (0:CRU 1:GPIO) 95 * @tshut_polarity: the hardware-controlled active polarity (0:LOW 1:HIGH) 96 * @initialize: SoC special initialize tsadc controller method 97 * @irq_ack: clear the interrupt 98 * @get_temp: get the temperature 99 * @set_alarm_temp: set the high temperature interrupt 100 * @set_tshut_temp: set the hardware-controlled shutdown temperature 101 * @set_tshut_mode: set the hardware-controlled shutdown mode 102 * @table: the chip-specific conversion table 103 */ 104 struct rockchip_tsadc_chip { 105 /* The sensor id of chip correspond to the ADC channel */ 106 int chn_id[SOC_MAX_SENSORS]; 107 int chn_num; 108 109 /* The hardware-controlled tshut property */ 110 int tshut_temp; 111 enum tshut_mode tshut_mode; 112 enum tshut_polarity tshut_polarity; 113 114 /* Chip-wide methods */ 115 void (*initialize)(struct regmap *grf, 116 void __iomem *reg, enum tshut_polarity p); 117 void (*irq_ack)(void __iomem *reg); 118 void (*control)(void __iomem *reg, bool on); 119 120 /* Per-sensor methods */ 121 int (*get_temp)(const struct chip_tsadc_table *table, 122 int chn, void __iomem *reg, int *temp); 123 int (*set_alarm_temp)(const struct chip_tsadc_table *table, 124 int chn, void __iomem *reg, int temp); 125 int (*set_tshut_temp)(const struct chip_tsadc_table *table, 126 int chn, void __iomem *reg, int temp); 127 void (*set_tshut_mode)(int chn, void __iomem *reg, enum tshut_mode m); 128 129 /* Per-table methods */ 130 struct chip_tsadc_table table; 131 }; 132 133 /** 134 * struct rockchip_thermal_sensor - hold the information of thermal sensor 135 * @thermal: pointer to the platform/configuration data 136 * @tzd: pointer to a thermal zone 137 * @id: identifier of the thermal sensor 138 */ 139 struct rockchip_thermal_sensor { 140 struct rockchip_thermal_data *thermal; 141 struct thermal_zone_device *tzd; 142 int id; 143 }; 144 145 /** 146 * struct rockchip_thermal_data - hold the private data of thermal driver 147 * @chip: pointer to the platform/configuration data 148 * @pdev: platform device of thermal 149 * @reset: the reset controller of tsadc 150 * @sensors[SOC_MAX_SENSORS]: the thermal sensor 151 * @clk: the controller clock is divided by the exteral 24MHz 152 * @pclk: the advanced peripherals bus clock 153 * @grf: the general register file will be used to do static set by software 154 * @regs: the base address of tsadc controller 155 * @tshut_temp: the hardware-controlled shutdown temperature value 156 * @tshut_mode: the hardware-controlled shutdown mode (0:CRU 1:GPIO) 157 * @tshut_polarity: the hardware-controlled active polarity (0:LOW 1:HIGH) 158 */ 159 struct rockchip_thermal_data { 160 const struct rockchip_tsadc_chip *chip; 161 struct platform_device *pdev; 162 struct reset_control *reset; 163 164 struct rockchip_thermal_sensor sensors[SOC_MAX_SENSORS]; 165 166 struct clk *clk; 167 struct clk *pclk; 168 169 struct regmap *grf; 170 void __iomem *regs; 171 172 int tshut_temp; 173 enum tshut_mode tshut_mode; 174 enum tshut_polarity tshut_polarity; 175 }; 176 177 /** 178 * TSADC Sensor Register description: 179 * 180 * TSADCV2_* are used for RK3288 SoCs, the other chips can reuse it. 181 * TSADCV3_* are used for newer SoCs than RK3288. (e.g: RK3228, RK3399) 182 * 183 */ 184 #define TSADCV2_USER_CON 0x00 185 #define TSADCV2_AUTO_CON 0x04 186 #define TSADCV2_INT_EN 0x08 187 #define TSADCV2_INT_PD 0x0c 188 #define TSADCV2_DATA(chn) (0x20 + (chn) * 0x04) 189 #define TSADCV2_COMP_INT(chn) (0x30 + (chn) * 0x04) 190 #define TSADCV2_COMP_SHUT(chn) (0x40 + (chn) * 0x04) 191 #define TSADCV2_HIGHT_INT_DEBOUNCE 0x60 192 #define TSADCV2_HIGHT_TSHUT_DEBOUNCE 0x64 193 #define TSADCV2_AUTO_PERIOD 0x68 194 #define TSADCV2_AUTO_PERIOD_HT 0x6c 195 196 #define TSADCV2_AUTO_EN BIT(0) 197 #define TSADCV2_AUTO_SRC_EN(chn) BIT(4 + (chn)) 198 #define TSADCV2_AUTO_TSHUT_POLARITY_HIGH BIT(8) 199 200 #define TSADCV3_AUTO_Q_SEL_EN BIT(1) 201 202 #define TSADCV2_INT_SRC_EN(chn) BIT(chn) 203 #define TSADCV2_SHUT_2GPIO_SRC_EN(chn) BIT(4 + (chn)) 204 #define TSADCV2_SHUT_2CRU_SRC_EN(chn) BIT(8 + (chn)) 205 206 #define TSADCV2_INT_PD_CLEAR_MASK ~BIT(8) 207 #define TSADCV3_INT_PD_CLEAR_MASK ~BIT(16) 208 209 #define TSADCV2_DATA_MASK 0xfff 210 #define TSADCV3_DATA_MASK 0x3ff 211 212 #define TSADCV2_HIGHT_INT_DEBOUNCE_COUNT 4 213 #define TSADCV2_HIGHT_TSHUT_DEBOUNCE_COUNT 4 214 #define TSADCV2_AUTO_PERIOD_TIME 250 /* 250ms */ 215 #define TSADCV2_AUTO_PERIOD_HT_TIME 50 /* 50ms */ 216 #define TSADCV3_AUTO_PERIOD_TIME 1875 /* 2.5ms */ 217 #define TSADCV3_AUTO_PERIOD_HT_TIME 1875 /* 2.5ms */ 218 219 #define TSADCV2_USER_INTER_PD_SOC 0x340 /* 13 clocks */ 220 221 #define GRF_SARADC_TESTBIT 0x0e644 222 #define GRF_TSADC_TESTBIT_L 0x0e648 223 #define GRF_TSADC_TESTBIT_H 0x0e64c 224 225 #define GRF_SARADC_TESTBIT_ON (0x10001 << 2) 226 #define GRF_TSADC_TESTBIT_H_ON (0x10001 << 2) 227 #define GRF_TSADC_VCM_EN_L (0x10001 << 7) 228 #define GRF_TSADC_VCM_EN_H (0x10001 << 7) 229 230 /** 231 * struct tsadc_table - code to temperature conversion table 232 * @code: the value of adc channel 233 * @temp: the temperature 234 * Note: 235 * code to temperature mapping of the temperature sensor is a piece wise linear 236 * curve.Any temperature, code faling between to 2 give temperatures can be 237 * linearly interpolated. 238 * Code to Temperature mapping should be updated based on manufacturer results. 239 */ 240 struct tsadc_table { 241 u32 code; 242 int temp; 243 }; 244 245 static const struct tsadc_table rv1108_table[] = { 246 {0, -40000}, 247 {374, -40000}, 248 {382, -35000}, 249 {389, -30000}, 250 {397, -25000}, 251 {405, -20000}, 252 {413, -15000}, 253 {421, -10000}, 254 {429, -5000}, 255 {436, 0}, 256 {444, 5000}, 257 {452, 10000}, 258 {460, 15000}, 259 {468, 20000}, 260 {476, 25000}, 261 {483, 30000}, 262 {491, 35000}, 263 {499, 40000}, 264 {507, 45000}, 265 {515, 50000}, 266 {523, 55000}, 267 {531, 60000}, 268 {539, 65000}, 269 {547, 70000}, 270 {555, 75000}, 271 {562, 80000}, 272 {570, 85000}, 273 {578, 90000}, 274 {586, 95000}, 275 {594, 100000}, 276 {602, 105000}, 277 {610, 110000}, 278 {618, 115000}, 279 {626, 120000}, 280 {634, 125000}, 281 {TSADCV2_DATA_MASK, 125000}, 282 }; 283 284 static const struct tsadc_table rk3228_code_table[] = { 285 {0, -40000}, 286 {588, -40000}, 287 {593, -35000}, 288 {598, -30000}, 289 {603, -25000}, 290 {608, -20000}, 291 {613, -15000}, 292 {618, -10000}, 293 {623, -5000}, 294 {629, 0}, 295 {634, 5000}, 296 {639, 10000}, 297 {644, 15000}, 298 {649, 20000}, 299 {654, 25000}, 300 {660, 30000}, 301 {665, 35000}, 302 {670, 40000}, 303 {675, 45000}, 304 {681, 50000}, 305 {686, 55000}, 306 {691, 60000}, 307 {696, 65000}, 308 {702, 70000}, 309 {707, 75000}, 310 {712, 80000}, 311 {717, 85000}, 312 {723, 90000}, 313 {728, 95000}, 314 {733, 100000}, 315 {738, 105000}, 316 {744, 110000}, 317 {749, 115000}, 318 {754, 120000}, 319 {760, 125000}, 320 {TSADCV2_DATA_MASK, 125000}, 321 }; 322 323 static const struct tsadc_table rk3288_code_table[] = { 324 {TSADCV2_DATA_MASK, -40000}, 325 {3800, -40000}, 326 {3792, -35000}, 327 {3783, -30000}, 328 {3774, -25000}, 329 {3765, -20000}, 330 {3756, -15000}, 331 {3747, -10000}, 332 {3737, -5000}, 333 {3728, 0}, 334 {3718, 5000}, 335 {3708, 10000}, 336 {3698, 15000}, 337 {3688, 20000}, 338 {3678, 25000}, 339 {3667, 30000}, 340 {3656, 35000}, 341 {3645, 40000}, 342 {3634, 45000}, 343 {3623, 50000}, 344 {3611, 55000}, 345 {3600, 60000}, 346 {3588, 65000}, 347 {3575, 70000}, 348 {3563, 75000}, 349 {3550, 80000}, 350 {3537, 85000}, 351 {3524, 90000}, 352 {3510, 95000}, 353 {3496, 100000}, 354 {3482, 105000}, 355 {3467, 110000}, 356 {3452, 115000}, 357 {3437, 120000}, 358 {3421, 125000}, 359 {0, 125000}, 360 }; 361 362 static const struct tsadc_table rk3328_code_table[] = { 363 {0, -40000}, 364 {296, -40000}, 365 {304, -35000}, 366 {313, -30000}, 367 {331, -20000}, 368 {340, -15000}, 369 {349, -10000}, 370 {359, -5000}, 371 {368, 0}, 372 {378, 5000}, 373 {388, 10000}, 374 {398, 15000}, 375 {408, 20000}, 376 {418, 25000}, 377 {429, 30000}, 378 {440, 35000}, 379 {451, 40000}, 380 {462, 45000}, 381 {473, 50000}, 382 {485, 55000}, 383 {496, 60000}, 384 {508, 65000}, 385 {521, 70000}, 386 {533, 75000}, 387 {546, 80000}, 388 {559, 85000}, 389 {572, 90000}, 390 {586, 95000}, 391 {600, 100000}, 392 {614, 105000}, 393 {629, 110000}, 394 {644, 115000}, 395 {659, 120000}, 396 {675, 125000}, 397 {TSADCV2_DATA_MASK, 125000}, 398 }; 399 400 static const struct tsadc_table rk3368_code_table[] = { 401 {0, -40000}, 402 {106, -40000}, 403 {108, -35000}, 404 {110, -30000}, 405 {112, -25000}, 406 {114, -20000}, 407 {116, -15000}, 408 {118, -10000}, 409 {120, -5000}, 410 {122, 0}, 411 {124, 5000}, 412 {126, 10000}, 413 {128, 15000}, 414 {130, 20000}, 415 {132, 25000}, 416 {134, 30000}, 417 {136, 35000}, 418 {138, 40000}, 419 {140, 45000}, 420 {142, 50000}, 421 {144, 55000}, 422 {146, 60000}, 423 {148, 65000}, 424 {150, 70000}, 425 {152, 75000}, 426 {154, 80000}, 427 {156, 85000}, 428 {158, 90000}, 429 {160, 95000}, 430 {162, 100000}, 431 {163, 105000}, 432 {165, 110000}, 433 {167, 115000}, 434 {169, 120000}, 435 {171, 125000}, 436 {TSADCV3_DATA_MASK, 125000}, 437 }; 438 439 static const struct tsadc_table rk3399_code_table[] = { 440 {0, -40000}, 441 {402, -40000}, 442 {410, -35000}, 443 {419, -30000}, 444 {427, -25000}, 445 {436, -20000}, 446 {444, -15000}, 447 {453, -10000}, 448 {461, -5000}, 449 {470, 0}, 450 {478, 5000}, 451 {487, 10000}, 452 {496, 15000}, 453 {504, 20000}, 454 {513, 25000}, 455 {521, 30000}, 456 {530, 35000}, 457 {538, 40000}, 458 {547, 45000}, 459 {555, 50000}, 460 {564, 55000}, 461 {573, 60000}, 462 {581, 65000}, 463 {590, 70000}, 464 {599, 75000}, 465 {607, 80000}, 466 {616, 85000}, 467 {624, 90000}, 468 {633, 95000}, 469 {642, 100000}, 470 {650, 105000}, 471 {659, 110000}, 472 {668, 115000}, 473 {677, 120000}, 474 {685, 125000}, 475 {TSADCV3_DATA_MASK, 125000}, 476 }; 477 478 static u32 rk_tsadcv2_temp_to_code(const struct chip_tsadc_table *table, 479 int temp) 480 { 481 int high, low, mid; 482 unsigned long num; 483 unsigned int denom; 484 u32 error = table->data_mask; 485 486 low = 0; 487 high = (table->length - 1) - 1; /* ignore the last check for table */ 488 mid = (high + low) / 2; 489 490 /* Return mask code data when the temp is over table range */ 491 if (temp < table->id[low].temp || temp > table->id[high].temp) 492 goto exit; 493 494 while (low <= high) { 495 if (temp == table->id[mid].temp) 496 return table->id[mid].code; 497 else if (temp < table->id[mid].temp) 498 high = mid - 1; 499 else 500 low = mid + 1; 501 mid = (low + high) / 2; 502 } 503 504 /* 505 * The conversion code granularity provided by the table. Let's 506 * assume that the relationship between temperature and 507 * analog value between 2 table entries is linear and interpolate 508 * to produce less granular result. 509 */ 510 num = abs(table->id[mid + 1].code - table->id[mid].code); 511 num *= temp - table->id[mid].temp; 512 denom = table->id[mid + 1].temp - table->id[mid].temp; 513 514 switch (table->mode) { 515 case ADC_DECREMENT: 516 return table->id[mid].code - (num / denom); 517 case ADC_INCREMENT: 518 return table->id[mid].code + (num / denom); 519 default: 520 pr_err("%s: unknown table mode: %d\n", __func__, table->mode); 521 return error; 522 } 523 524 exit: 525 pr_err("%s: invalid temperature, temp=%d error=%d\n", 526 __func__, temp, error); 527 return error; 528 } 529 530 static int rk_tsadcv2_code_to_temp(const struct chip_tsadc_table *table, 531 u32 code, int *temp) 532 { 533 unsigned int low = 1; 534 unsigned int high = table->length - 1; 535 unsigned int mid = (low + high) / 2; 536 unsigned int num; 537 unsigned long denom; 538 539 WARN_ON(table->length < 2); 540 541 switch (table->mode) { 542 case ADC_DECREMENT: 543 code &= table->data_mask; 544 if (code <= table->id[high].code) 545 return -EAGAIN; /* Incorrect reading */ 546 547 while (low <= high) { 548 if (code >= table->id[mid].code && 549 code < table->id[mid - 1].code) 550 break; 551 else if (code < table->id[mid].code) 552 low = mid + 1; 553 else 554 high = mid - 1; 555 556 mid = (low + high) / 2; 557 } 558 break; 559 case ADC_INCREMENT: 560 code &= table->data_mask; 561 if (code < table->id[low].code) 562 return -EAGAIN; /* Incorrect reading */ 563 564 while (low <= high) { 565 if (code <= table->id[mid].code && 566 code > table->id[mid - 1].code) 567 break; 568 else if (code > table->id[mid].code) 569 low = mid + 1; 570 else 571 high = mid - 1; 572 573 mid = (low + high) / 2; 574 } 575 break; 576 default: 577 pr_err("%s: unknown table mode: %d\n", __func__, table->mode); 578 return -EINVAL; 579 } 580 581 /* 582 * The 5C granularity provided by the table is too much. Let's 583 * assume that the relationship between sensor readings and 584 * temperature between 2 table entries is linear and interpolate 585 * to produce less granular result. 586 */ 587 num = table->id[mid].temp - table->id[mid - 1].temp; 588 num *= abs(table->id[mid - 1].code - code); 589 denom = abs(table->id[mid - 1].code - table->id[mid].code); 590 *temp = table->id[mid - 1].temp + (num / denom); 591 592 return 0; 593 } 594 595 /** 596 * rk_tsadcv2_initialize - initialize TASDC Controller. 597 * 598 * (1) Set TSADC_V2_AUTO_PERIOD: 599 * Configure the interleave between every two accessing of 600 * TSADC in normal operation. 601 * 602 * (2) Set TSADCV2_AUTO_PERIOD_HT: 603 * Configure the interleave between every two accessing of 604 * TSADC after the temperature is higher than COM_SHUT or COM_INT. 605 * 606 * (3) Set TSADCV2_HIGH_INT_DEBOUNCE and TSADC_HIGHT_TSHUT_DEBOUNCE: 607 * If the temperature is higher than COMP_INT or COMP_SHUT for 608 * "debounce" times, TSADC controller will generate interrupt or TSHUT. 609 */ 610 static void rk_tsadcv2_initialize(struct regmap *grf, void __iomem *regs, 611 enum tshut_polarity tshut_polarity) 612 { 613 if (tshut_polarity == TSHUT_HIGH_ACTIVE) 614 writel_relaxed(0U | TSADCV2_AUTO_TSHUT_POLARITY_HIGH, 615 regs + TSADCV2_AUTO_CON); 616 else 617 writel_relaxed(0U & ~TSADCV2_AUTO_TSHUT_POLARITY_HIGH, 618 regs + TSADCV2_AUTO_CON); 619 620 writel_relaxed(TSADCV2_AUTO_PERIOD_TIME, regs + TSADCV2_AUTO_PERIOD); 621 writel_relaxed(TSADCV2_HIGHT_INT_DEBOUNCE_COUNT, 622 regs + TSADCV2_HIGHT_INT_DEBOUNCE); 623 writel_relaxed(TSADCV2_AUTO_PERIOD_HT_TIME, 624 regs + TSADCV2_AUTO_PERIOD_HT); 625 writel_relaxed(TSADCV2_HIGHT_TSHUT_DEBOUNCE_COUNT, 626 regs + TSADCV2_HIGHT_TSHUT_DEBOUNCE); 627 } 628 629 /** 630 * rk_tsadcv3_initialize - initialize TASDC Controller. 631 * 632 * (1) The tsadc control power sequence. 633 * 634 * (2) Set TSADC_V2_AUTO_PERIOD: 635 * Configure the interleave between every two accessing of 636 * TSADC in normal operation. 637 * 638 * (2) Set TSADCV2_AUTO_PERIOD_HT: 639 * Configure the interleave between every two accessing of 640 * TSADC after the temperature is higher than COM_SHUT or COM_INT. 641 * 642 * (3) Set TSADCV2_HIGH_INT_DEBOUNCE and TSADC_HIGHT_TSHUT_DEBOUNCE: 643 * If the temperature is higher than COMP_INT or COMP_SHUT for 644 * "debounce" times, TSADC controller will generate interrupt or TSHUT. 645 */ 646 static void rk_tsadcv3_initialize(struct regmap *grf, void __iomem *regs, 647 enum tshut_polarity tshut_polarity) 648 { 649 /* The tsadc control power sequence */ 650 if (IS_ERR(grf)) { 651 /* Set interleave value to workround ic time sync issue */ 652 writel_relaxed(TSADCV2_USER_INTER_PD_SOC, regs + 653 TSADCV2_USER_CON); 654 655 writel_relaxed(TSADCV2_AUTO_PERIOD_TIME, 656 regs + TSADCV2_AUTO_PERIOD); 657 writel_relaxed(TSADCV2_HIGHT_INT_DEBOUNCE_COUNT, 658 regs + TSADCV2_HIGHT_INT_DEBOUNCE); 659 writel_relaxed(TSADCV2_AUTO_PERIOD_HT_TIME, 660 regs + TSADCV2_AUTO_PERIOD_HT); 661 writel_relaxed(TSADCV2_HIGHT_TSHUT_DEBOUNCE_COUNT, 662 regs + TSADCV2_HIGHT_TSHUT_DEBOUNCE); 663 664 } else { 665 /* Enable the voltage common mode feature */ 666 regmap_write(grf, GRF_TSADC_TESTBIT_L, GRF_TSADC_VCM_EN_L); 667 regmap_write(grf, GRF_TSADC_TESTBIT_H, GRF_TSADC_VCM_EN_H); 668 669 usleep_range(15, 100); /* The spec note says at least 15 us */ 670 regmap_write(grf, GRF_SARADC_TESTBIT, GRF_SARADC_TESTBIT_ON); 671 regmap_write(grf, GRF_TSADC_TESTBIT_H, GRF_TSADC_TESTBIT_H_ON); 672 usleep_range(90, 200); /* The spec note says at least 90 us */ 673 674 writel_relaxed(TSADCV3_AUTO_PERIOD_TIME, 675 regs + TSADCV2_AUTO_PERIOD); 676 writel_relaxed(TSADCV2_HIGHT_INT_DEBOUNCE_COUNT, 677 regs + TSADCV2_HIGHT_INT_DEBOUNCE); 678 writel_relaxed(TSADCV3_AUTO_PERIOD_HT_TIME, 679 regs + TSADCV2_AUTO_PERIOD_HT); 680 writel_relaxed(TSADCV2_HIGHT_TSHUT_DEBOUNCE_COUNT, 681 regs + TSADCV2_HIGHT_TSHUT_DEBOUNCE); 682 } 683 684 if (tshut_polarity == TSHUT_HIGH_ACTIVE) 685 writel_relaxed(0U | TSADCV2_AUTO_TSHUT_POLARITY_HIGH, 686 regs + TSADCV2_AUTO_CON); 687 else 688 writel_relaxed(0U & ~TSADCV2_AUTO_TSHUT_POLARITY_HIGH, 689 regs + TSADCV2_AUTO_CON); 690 } 691 692 static void rk_tsadcv2_irq_ack(void __iomem *regs) 693 { 694 u32 val; 695 696 val = readl_relaxed(regs + TSADCV2_INT_PD); 697 writel_relaxed(val & TSADCV2_INT_PD_CLEAR_MASK, regs + TSADCV2_INT_PD); 698 } 699 700 static void rk_tsadcv3_irq_ack(void __iomem *regs) 701 { 702 u32 val; 703 704 val = readl_relaxed(regs + TSADCV2_INT_PD); 705 writel_relaxed(val & TSADCV3_INT_PD_CLEAR_MASK, regs + TSADCV2_INT_PD); 706 } 707 708 static void rk_tsadcv2_control(void __iomem *regs, bool enable) 709 { 710 u32 val; 711 712 val = readl_relaxed(regs + TSADCV2_AUTO_CON); 713 if (enable) 714 val |= TSADCV2_AUTO_EN; 715 else 716 val &= ~TSADCV2_AUTO_EN; 717 718 writel_relaxed(val, regs + TSADCV2_AUTO_CON); 719 } 720 721 /** 722 * rk_tsadcv3_control - the tsadc controller is enabled or disabled. 723 * 724 * NOTE: TSADC controller works at auto mode, and some SoCs need set the 725 * tsadc_q_sel bit on TSADCV2_AUTO_CON[1]. The (1024 - tsadc_q) as output 726 * adc value if setting this bit to enable. 727 */ 728 static void rk_tsadcv3_control(void __iomem *regs, bool enable) 729 { 730 u32 val; 731 732 val = readl_relaxed(regs + TSADCV2_AUTO_CON); 733 if (enable) 734 val |= TSADCV2_AUTO_EN | TSADCV3_AUTO_Q_SEL_EN; 735 else 736 val &= ~TSADCV2_AUTO_EN; 737 738 writel_relaxed(val, regs + TSADCV2_AUTO_CON); 739 } 740 741 static int rk_tsadcv2_get_temp(const struct chip_tsadc_table *table, 742 int chn, void __iomem *regs, int *temp) 743 { 744 u32 val; 745 746 val = readl_relaxed(regs + TSADCV2_DATA(chn)); 747 748 return rk_tsadcv2_code_to_temp(table, val, temp); 749 } 750 751 static int rk_tsadcv2_alarm_temp(const struct chip_tsadc_table *table, 752 int chn, void __iomem *regs, int temp) 753 { 754 u32 alarm_value; 755 u32 int_en, int_clr; 756 757 /* 758 * In some cases, some sensors didn't need the trip points, the 759 * set_trips will pass {-INT_MAX, INT_MAX} to trigger tsadc alarm 760 * in the end, ignore this case and disable the high temperature 761 * interrupt. 762 */ 763 if (temp == INT_MAX) { 764 int_clr = readl_relaxed(regs + TSADCV2_INT_EN); 765 int_clr &= ~TSADCV2_INT_SRC_EN(chn); 766 writel_relaxed(int_clr, regs + TSADCV2_INT_EN); 767 return 0; 768 } 769 770 /* Make sure the value is valid */ 771 alarm_value = rk_tsadcv2_temp_to_code(table, temp); 772 if (alarm_value == table->data_mask) 773 return -ERANGE; 774 775 writel_relaxed(alarm_value & table->data_mask, 776 regs + TSADCV2_COMP_INT(chn)); 777 778 int_en = readl_relaxed(regs + TSADCV2_INT_EN); 779 int_en |= TSADCV2_INT_SRC_EN(chn); 780 writel_relaxed(int_en, regs + TSADCV2_INT_EN); 781 782 return 0; 783 } 784 785 static int rk_tsadcv2_tshut_temp(const struct chip_tsadc_table *table, 786 int chn, void __iomem *regs, int temp) 787 { 788 u32 tshut_value, val; 789 790 /* Make sure the value is valid */ 791 tshut_value = rk_tsadcv2_temp_to_code(table, temp); 792 if (tshut_value == table->data_mask) 793 return -ERANGE; 794 795 writel_relaxed(tshut_value, regs + TSADCV2_COMP_SHUT(chn)); 796 797 /* TSHUT will be valid */ 798 val = readl_relaxed(regs + TSADCV2_AUTO_CON); 799 writel_relaxed(val | TSADCV2_AUTO_SRC_EN(chn), regs + TSADCV2_AUTO_CON); 800 801 return 0; 802 } 803 804 static void rk_tsadcv2_tshut_mode(int chn, void __iomem *regs, 805 enum tshut_mode mode) 806 { 807 u32 val; 808 809 val = readl_relaxed(regs + TSADCV2_INT_EN); 810 if (mode == TSHUT_MODE_GPIO) { 811 val &= ~TSADCV2_SHUT_2CRU_SRC_EN(chn); 812 val |= TSADCV2_SHUT_2GPIO_SRC_EN(chn); 813 } else { 814 val &= ~TSADCV2_SHUT_2GPIO_SRC_EN(chn); 815 val |= TSADCV2_SHUT_2CRU_SRC_EN(chn); 816 } 817 818 writel_relaxed(val, regs + TSADCV2_INT_EN); 819 } 820 821 static const struct rockchip_tsadc_chip rv1108_tsadc_data = { 822 .chn_id[SENSOR_CPU] = 0, /* cpu sensor is channel 0 */ 823 .chn_num = 1, /* one channel for tsadc */ 824 825 .tshut_mode = TSHUT_MODE_GPIO, /* default TSHUT via GPIO give PMIC */ 826 .tshut_polarity = TSHUT_LOW_ACTIVE, /* default TSHUT LOW ACTIVE */ 827 .tshut_temp = 95000, 828 829 .initialize = rk_tsadcv2_initialize, 830 .irq_ack = rk_tsadcv3_irq_ack, 831 .control = rk_tsadcv3_control, 832 .get_temp = rk_tsadcv2_get_temp, 833 .set_alarm_temp = rk_tsadcv2_alarm_temp, 834 .set_tshut_temp = rk_tsadcv2_tshut_temp, 835 .set_tshut_mode = rk_tsadcv2_tshut_mode, 836 837 .table = { 838 .id = rv1108_table, 839 .length = ARRAY_SIZE(rv1108_table), 840 .data_mask = TSADCV2_DATA_MASK, 841 .mode = ADC_INCREMENT, 842 }, 843 }; 844 845 static const struct rockchip_tsadc_chip rk3228_tsadc_data = { 846 .chn_id[SENSOR_CPU] = 0, /* cpu sensor is channel 0 */ 847 .chn_num = 1, /* one channel for tsadc */ 848 849 .tshut_mode = TSHUT_MODE_GPIO, /* default TSHUT via GPIO give PMIC */ 850 .tshut_polarity = TSHUT_LOW_ACTIVE, /* default TSHUT LOW ACTIVE */ 851 .tshut_temp = 95000, 852 853 .initialize = rk_tsadcv2_initialize, 854 .irq_ack = rk_tsadcv3_irq_ack, 855 .control = rk_tsadcv3_control, 856 .get_temp = rk_tsadcv2_get_temp, 857 .set_alarm_temp = rk_tsadcv2_alarm_temp, 858 .set_tshut_temp = rk_tsadcv2_tshut_temp, 859 .set_tshut_mode = rk_tsadcv2_tshut_mode, 860 861 .table = { 862 .id = rk3228_code_table, 863 .length = ARRAY_SIZE(rk3228_code_table), 864 .data_mask = TSADCV3_DATA_MASK, 865 .mode = ADC_INCREMENT, 866 }, 867 }; 868 869 static const struct rockchip_tsadc_chip rk3288_tsadc_data = { 870 .chn_id[SENSOR_CPU] = 1, /* cpu sensor is channel 1 */ 871 .chn_id[SENSOR_GPU] = 2, /* gpu sensor is channel 2 */ 872 .chn_num = 2, /* two channels for tsadc */ 873 874 .tshut_mode = TSHUT_MODE_GPIO, /* default TSHUT via GPIO give PMIC */ 875 .tshut_polarity = TSHUT_LOW_ACTIVE, /* default TSHUT LOW ACTIVE */ 876 .tshut_temp = 95000, 877 878 .initialize = rk_tsadcv2_initialize, 879 .irq_ack = rk_tsadcv2_irq_ack, 880 .control = rk_tsadcv2_control, 881 .get_temp = rk_tsadcv2_get_temp, 882 .set_alarm_temp = rk_tsadcv2_alarm_temp, 883 .set_tshut_temp = rk_tsadcv2_tshut_temp, 884 .set_tshut_mode = rk_tsadcv2_tshut_mode, 885 886 .table = { 887 .id = rk3288_code_table, 888 .length = ARRAY_SIZE(rk3288_code_table), 889 .data_mask = TSADCV2_DATA_MASK, 890 .mode = ADC_DECREMENT, 891 }, 892 }; 893 894 static const struct rockchip_tsadc_chip rk3328_tsadc_data = { 895 .chn_id[SENSOR_CPU] = 0, /* cpu sensor is channel 0 */ 896 .chn_num = 1, /* one channels for tsadc */ 897 898 .tshut_mode = TSHUT_MODE_CRU, /* default TSHUT via CRU */ 899 .tshut_temp = 95000, 900 901 .initialize = rk_tsadcv2_initialize, 902 .irq_ack = rk_tsadcv3_irq_ack, 903 .control = rk_tsadcv3_control, 904 .get_temp = rk_tsadcv2_get_temp, 905 .set_alarm_temp = rk_tsadcv2_alarm_temp, 906 .set_tshut_temp = rk_tsadcv2_tshut_temp, 907 .set_tshut_mode = rk_tsadcv2_tshut_mode, 908 909 .table = { 910 .id = rk3328_code_table, 911 .length = ARRAY_SIZE(rk3328_code_table), 912 .data_mask = TSADCV2_DATA_MASK, 913 .mode = ADC_INCREMENT, 914 }, 915 }; 916 917 static const struct rockchip_tsadc_chip rk3366_tsadc_data = { 918 .chn_id[SENSOR_CPU] = 0, /* cpu sensor is channel 0 */ 919 .chn_id[SENSOR_GPU] = 1, /* gpu sensor is channel 1 */ 920 .chn_num = 2, /* two channels for tsadc */ 921 922 .tshut_mode = TSHUT_MODE_GPIO, /* default TSHUT via GPIO give PMIC */ 923 .tshut_polarity = TSHUT_LOW_ACTIVE, /* default TSHUT LOW ACTIVE */ 924 .tshut_temp = 95000, 925 926 .initialize = rk_tsadcv3_initialize, 927 .irq_ack = rk_tsadcv3_irq_ack, 928 .control = rk_tsadcv3_control, 929 .get_temp = rk_tsadcv2_get_temp, 930 .set_alarm_temp = rk_tsadcv2_alarm_temp, 931 .set_tshut_temp = rk_tsadcv2_tshut_temp, 932 .set_tshut_mode = rk_tsadcv2_tshut_mode, 933 934 .table = { 935 .id = rk3228_code_table, 936 .length = ARRAY_SIZE(rk3228_code_table), 937 .data_mask = TSADCV3_DATA_MASK, 938 .mode = ADC_INCREMENT, 939 }, 940 }; 941 942 static const struct rockchip_tsadc_chip rk3368_tsadc_data = { 943 .chn_id[SENSOR_CPU] = 0, /* cpu sensor is channel 0 */ 944 .chn_id[SENSOR_GPU] = 1, /* gpu sensor is channel 1 */ 945 .chn_num = 2, /* two channels for tsadc */ 946 947 .tshut_mode = TSHUT_MODE_GPIO, /* default TSHUT via GPIO give PMIC */ 948 .tshut_polarity = TSHUT_LOW_ACTIVE, /* default TSHUT LOW ACTIVE */ 949 .tshut_temp = 95000, 950 951 .initialize = rk_tsadcv2_initialize, 952 .irq_ack = rk_tsadcv2_irq_ack, 953 .control = rk_tsadcv2_control, 954 .get_temp = rk_tsadcv2_get_temp, 955 .set_alarm_temp = rk_tsadcv2_alarm_temp, 956 .set_tshut_temp = rk_tsadcv2_tshut_temp, 957 .set_tshut_mode = rk_tsadcv2_tshut_mode, 958 959 .table = { 960 .id = rk3368_code_table, 961 .length = ARRAY_SIZE(rk3368_code_table), 962 .data_mask = TSADCV3_DATA_MASK, 963 .mode = ADC_INCREMENT, 964 }, 965 }; 966 967 static const struct rockchip_tsadc_chip rk3399_tsadc_data = { 968 .chn_id[SENSOR_CPU] = 0, /* cpu sensor is channel 0 */ 969 .chn_id[SENSOR_GPU] = 1, /* gpu sensor is channel 1 */ 970 .chn_num = 2, /* two channels for tsadc */ 971 972 .tshut_mode = TSHUT_MODE_GPIO, /* default TSHUT via GPIO give PMIC */ 973 .tshut_polarity = TSHUT_LOW_ACTIVE, /* default TSHUT LOW ACTIVE */ 974 .tshut_temp = 95000, 975 976 .initialize = rk_tsadcv3_initialize, 977 .irq_ack = rk_tsadcv3_irq_ack, 978 .control = rk_tsadcv3_control, 979 .get_temp = rk_tsadcv2_get_temp, 980 .set_alarm_temp = rk_tsadcv2_alarm_temp, 981 .set_tshut_temp = rk_tsadcv2_tshut_temp, 982 .set_tshut_mode = rk_tsadcv2_tshut_mode, 983 984 .table = { 985 .id = rk3399_code_table, 986 .length = ARRAY_SIZE(rk3399_code_table), 987 .data_mask = TSADCV3_DATA_MASK, 988 .mode = ADC_INCREMENT, 989 }, 990 }; 991 992 static const struct of_device_id of_rockchip_thermal_match[] = { 993 { 994 .compatible = "rockchip,rv1108-tsadc", 995 .data = (void *)&rv1108_tsadc_data, 996 }, 997 { 998 .compatible = "rockchip,rk3228-tsadc", 999 .data = (void *)&rk3228_tsadc_data, 1000 }, 1001 { 1002 .compatible = "rockchip,rk3288-tsadc", 1003 .data = (void *)&rk3288_tsadc_data, 1004 }, 1005 { 1006 .compatible = "rockchip,rk3328-tsadc", 1007 .data = (void *)&rk3328_tsadc_data, 1008 }, 1009 { 1010 .compatible = "rockchip,rk3366-tsadc", 1011 .data = (void *)&rk3366_tsadc_data, 1012 }, 1013 { 1014 .compatible = "rockchip,rk3368-tsadc", 1015 .data = (void *)&rk3368_tsadc_data, 1016 }, 1017 { 1018 .compatible = "rockchip,rk3399-tsadc", 1019 .data = (void *)&rk3399_tsadc_data, 1020 }, 1021 { /* end */ }, 1022 }; 1023 MODULE_DEVICE_TABLE(of, of_rockchip_thermal_match); 1024 1025 static void 1026 rockchip_thermal_toggle_sensor(struct rockchip_thermal_sensor *sensor, bool on) 1027 { 1028 struct thermal_zone_device *tzd = sensor->tzd; 1029 1030 tzd->ops->set_mode(tzd, 1031 on ? THERMAL_DEVICE_ENABLED : THERMAL_DEVICE_DISABLED); 1032 } 1033 1034 static irqreturn_t rockchip_thermal_alarm_irq_thread(int irq, void *dev) 1035 { 1036 struct rockchip_thermal_data *thermal = dev; 1037 int i; 1038 1039 dev_dbg(&thermal->pdev->dev, "thermal alarm\n"); 1040 1041 thermal->chip->irq_ack(thermal->regs); 1042 1043 for (i = 0; i < thermal->chip->chn_num; i++) 1044 thermal_zone_device_update(thermal->sensors[i].tzd, 1045 THERMAL_EVENT_UNSPECIFIED); 1046 1047 return IRQ_HANDLED; 1048 } 1049 1050 static int rockchip_thermal_set_trips(void *_sensor, int low, int high) 1051 { 1052 struct rockchip_thermal_sensor *sensor = _sensor; 1053 struct rockchip_thermal_data *thermal = sensor->thermal; 1054 const struct rockchip_tsadc_chip *tsadc = thermal->chip; 1055 1056 dev_dbg(&thermal->pdev->dev, "%s: sensor %d: low: %d, high %d\n", 1057 __func__, sensor->id, low, high); 1058 1059 return tsadc->set_alarm_temp(&tsadc->table, 1060 sensor->id, thermal->regs, high); 1061 } 1062 1063 static int rockchip_thermal_get_temp(void *_sensor, int *out_temp) 1064 { 1065 struct rockchip_thermal_sensor *sensor = _sensor; 1066 struct rockchip_thermal_data *thermal = sensor->thermal; 1067 const struct rockchip_tsadc_chip *tsadc = sensor->thermal->chip; 1068 int retval; 1069 1070 retval = tsadc->get_temp(&tsadc->table, 1071 sensor->id, thermal->regs, out_temp); 1072 dev_dbg(&thermal->pdev->dev, "sensor %d - temp: %d, retval: %d\n", 1073 sensor->id, *out_temp, retval); 1074 1075 return retval; 1076 } 1077 1078 static const struct thermal_zone_of_device_ops rockchip_of_thermal_ops = { 1079 .get_temp = rockchip_thermal_get_temp, 1080 .set_trips = rockchip_thermal_set_trips, 1081 }; 1082 1083 static int rockchip_configure_from_dt(struct device *dev, 1084 struct device_node *np, 1085 struct rockchip_thermal_data *thermal) 1086 { 1087 u32 shut_temp, tshut_mode, tshut_polarity; 1088 1089 if (of_property_read_u32(np, "rockchip,hw-tshut-temp", &shut_temp)) { 1090 dev_warn(dev, 1091 "Missing tshut temp property, using default %d\n", 1092 thermal->chip->tshut_temp); 1093 thermal->tshut_temp = thermal->chip->tshut_temp; 1094 } else { 1095 if (shut_temp > INT_MAX) { 1096 dev_err(dev, "Invalid tshut temperature specified: %d\n", 1097 shut_temp); 1098 return -ERANGE; 1099 } 1100 thermal->tshut_temp = shut_temp; 1101 } 1102 1103 if (of_property_read_u32(np, "rockchip,hw-tshut-mode", &tshut_mode)) { 1104 dev_warn(dev, 1105 "Missing tshut mode property, using default (%s)\n", 1106 thermal->chip->tshut_mode == TSHUT_MODE_GPIO ? 1107 "gpio" : "cru"); 1108 thermal->tshut_mode = thermal->chip->tshut_mode; 1109 } else { 1110 thermal->tshut_mode = tshut_mode; 1111 } 1112 1113 if (thermal->tshut_mode > 1) { 1114 dev_err(dev, "Invalid tshut mode specified: %d\n", 1115 thermal->tshut_mode); 1116 return -EINVAL; 1117 } 1118 1119 if (of_property_read_u32(np, "rockchip,hw-tshut-polarity", 1120 &tshut_polarity)) { 1121 dev_warn(dev, 1122 "Missing tshut-polarity property, using default (%s)\n", 1123 thermal->chip->tshut_polarity == TSHUT_LOW_ACTIVE ? 1124 "low" : "high"); 1125 thermal->tshut_polarity = thermal->chip->tshut_polarity; 1126 } else { 1127 thermal->tshut_polarity = tshut_polarity; 1128 } 1129 1130 if (thermal->tshut_polarity > 1) { 1131 dev_err(dev, "Invalid tshut-polarity specified: %d\n", 1132 thermal->tshut_polarity); 1133 return -EINVAL; 1134 } 1135 1136 /* The tsadc wont to handle the error in here since some SoCs didn't 1137 * need this property. 1138 */ 1139 thermal->grf = syscon_regmap_lookup_by_phandle(np, "rockchip,grf"); 1140 if (IS_ERR(thermal->grf)) 1141 dev_warn(dev, "Missing rockchip,grf property\n"); 1142 1143 return 0; 1144 } 1145 1146 static int 1147 rockchip_thermal_register_sensor(struct platform_device *pdev, 1148 struct rockchip_thermal_data *thermal, 1149 struct rockchip_thermal_sensor *sensor, 1150 int id) 1151 { 1152 const struct rockchip_tsadc_chip *tsadc = thermal->chip; 1153 int error; 1154 1155 tsadc->set_tshut_mode(id, thermal->regs, thermal->tshut_mode); 1156 1157 error = tsadc->set_tshut_temp(&tsadc->table, id, thermal->regs, 1158 thermal->tshut_temp); 1159 if (error) 1160 dev_err(&pdev->dev, "%s: invalid tshut=%d, error=%d\n", 1161 __func__, thermal->tshut_temp, error); 1162 1163 sensor->thermal = thermal; 1164 sensor->id = id; 1165 sensor->tzd = devm_thermal_zone_of_sensor_register(&pdev->dev, id, 1166 sensor, &rockchip_of_thermal_ops); 1167 if (IS_ERR(sensor->tzd)) { 1168 error = PTR_ERR(sensor->tzd); 1169 dev_err(&pdev->dev, "failed to register sensor %d: %d\n", 1170 id, error); 1171 return error; 1172 } 1173 1174 return 0; 1175 } 1176 1177 /** 1178 * Reset TSADC Controller, reset all tsadc registers. 1179 */ 1180 static void rockchip_thermal_reset_controller(struct reset_control *reset) 1181 { 1182 reset_control_assert(reset); 1183 usleep_range(10, 20); 1184 reset_control_deassert(reset); 1185 } 1186 1187 static int rockchip_thermal_probe(struct platform_device *pdev) 1188 { 1189 struct device_node *np = pdev->dev.of_node; 1190 struct rockchip_thermal_data *thermal; 1191 const struct of_device_id *match; 1192 struct resource *res; 1193 int irq; 1194 int i; 1195 int error; 1196 1197 match = of_match_node(of_rockchip_thermal_match, np); 1198 if (!match) 1199 return -ENXIO; 1200 1201 irq = platform_get_irq(pdev, 0); 1202 if (irq < 0) { 1203 dev_err(&pdev->dev, "no irq resource?\n"); 1204 return -EINVAL; 1205 } 1206 1207 thermal = devm_kzalloc(&pdev->dev, sizeof(struct rockchip_thermal_data), 1208 GFP_KERNEL); 1209 if (!thermal) 1210 return -ENOMEM; 1211 1212 thermal->pdev = pdev; 1213 1214 thermal->chip = (const struct rockchip_tsadc_chip *)match->data; 1215 if (!thermal->chip) 1216 return -EINVAL; 1217 1218 res = platform_get_resource(pdev, IORESOURCE_MEM, 0); 1219 thermal->regs = devm_ioremap_resource(&pdev->dev, res); 1220 if (IS_ERR(thermal->regs)) 1221 return PTR_ERR(thermal->regs); 1222 1223 thermal->reset = devm_reset_control_get(&pdev->dev, "tsadc-apb"); 1224 if (IS_ERR(thermal->reset)) { 1225 error = PTR_ERR(thermal->reset); 1226 dev_err(&pdev->dev, "failed to get tsadc reset: %d\n", error); 1227 return error; 1228 } 1229 1230 thermal->clk = devm_clk_get(&pdev->dev, "tsadc"); 1231 if (IS_ERR(thermal->clk)) { 1232 error = PTR_ERR(thermal->clk); 1233 dev_err(&pdev->dev, "failed to get tsadc clock: %d\n", error); 1234 return error; 1235 } 1236 1237 thermal->pclk = devm_clk_get(&pdev->dev, "apb_pclk"); 1238 if (IS_ERR(thermal->pclk)) { 1239 error = PTR_ERR(thermal->pclk); 1240 dev_err(&pdev->dev, "failed to get apb_pclk clock: %d\n", 1241 error); 1242 return error; 1243 } 1244 1245 error = clk_prepare_enable(thermal->clk); 1246 if (error) { 1247 dev_err(&pdev->dev, "failed to enable converter clock: %d\n", 1248 error); 1249 return error; 1250 } 1251 1252 error = clk_prepare_enable(thermal->pclk); 1253 if (error) { 1254 dev_err(&pdev->dev, "failed to enable pclk: %d\n", error); 1255 goto err_disable_clk; 1256 } 1257 1258 rockchip_thermal_reset_controller(thermal->reset); 1259 1260 error = rockchip_configure_from_dt(&pdev->dev, np, thermal); 1261 if (error) { 1262 dev_err(&pdev->dev, "failed to parse device tree data: %d\n", 1263 error); 1264 goto err_disable_pclk; 1265 } 1266 1267 thermal->chip->initialize(thermal->grf, thermal->regs, 1268 thermal->tshut_polarity); 1269 1270 for (i = 0; i < thermal->chip->chn_num; i++) { 1271 error = rockchip_thermal_register_sensor(pdev, thermal, 1272 &thermal->sensors[i], 1273 thermal->chip->chn_id[i]); 1274 if (error) { 1275 dev_err(&pdev->dev, 1276 "failed to register sensor[%d] : error = %d\n", 1277 i, error); 1278 goto err_disable_pclk; 1279 } 1280 } 1281 1282 error = devm_request_threaded_irq(&pdev->dev, irq, NULL, 1283 &rockchip_thermal_alarm_irq_thread, 1284 IRQF_ONESHOT, 1285 "rockchip_thermal", thermal); 1286 if (error) { 1287 dev_err(&pdev->dev, 1288 "failed to request tsadc irq: %d\n", error); 1289 goto err_disable_pclk; 1290 } 1291 1292 thermal->chip->control(thermal->regs, true); 1293 1294 for (i = 0; i < thermal->chip->chn_num; i++) 1295 rockchip_thermal_toggle_sensor(&thermal->sensors[i], true); 1296 1297 platform_set_drvdata(pdev, thermal); 1298 1299 return 0; 1300 1301 err_disable_pclk: 1302 clk_disable_unprepare(thermal->pclk); 1303 err_disable_clk: 1304 clk_disable_unprepare(thermal->clk); 1305 1306 return error; 1307 } 1308 1309 static int rockchip_thermal_remove(struct platform_device *pdev) 1310 { 1311 struct rockchip_thermal_data *thermal = platform_get_drvdata(pdev); 1312 int i; 1313 1314 for (i = 0; i < thermal->chip->chn_num; i++) { 1315 struct rockchip_thermal_sensor *sensor = &thermal->sensors[i]; 1316 1317 rockchip_thermal_toggle_sensor(sensor, false); 1318 } 1319 1320 thermal->chip->control(thermal->regs, false); 1321 1322 clk_disable_unprepare(thermal->pclk); 1323 clk_disable_unprepare(thermal->clk); 1324 1325 return 0; 1326 } 1327 1328 static int __maybe_unused rockchip_thermal_suspend(struct device *dev) 1329 { 1330 struct platform_device *pdev = to_platform_device(dev); 1331 struct rockchip_thermal_data *thermal = platform_get_drvdata(pdev); 1332 int i; 1333 1334 for (i = 0; i < thermal->chip->chn_num; i++) 1335 rockchip_thermal_toggle_sensor(&thermal->sensors[i], false); 1336 1337 thermal->chip->control(thermal->regs, false); 1338 1339 clk_disable(thermal->pclk); 1340 clk_disable(thermal->clk); 1341 1342 pinctrl_pm_select_sleep_state(dev); 1343 1344 return 0; 1345 } 1346 1347 static int __maybe_unused rockchip_thermal_resume(struct device *dev) 1348 { 1349 struct platform_device *pdev = to_platform_device(dev); 1350 struct rockchip_thermal_data *thermal = platform_get_drvdata(pdev); 1351 int i; 1352 int error; 1353 1354 error = clk_enable(thermal->clk); 1355 if (error) 1356 return error; 1357 1358 error = clk_enable(thermal->pclk); 1359 if (error) { 1360 clk_disable(thermal->clk); 1361 return error; 1362 } 1363 1364 rockchip_thermal_reset_controller(thermal->reset); 1365 1366 thermal->chip->initialize(thermal->grf, thermal->regs, 1367 thermal->tshut_polarity); 1368 1369 for (i = 0; i < thermal->chip->chn_num; i++) { 1370 int id = thermal->sensors[i].id; 1371 1372 thermal->chip->set_tshut_mode(id, thermal->regs, 1373 thermal->tshut_mode); 1374 1375 error = thermal->chip->set_tshut_temp(&thermal->chip->table, 1376 id, thermal->regs, 1377 thermal->tshut_temp); 1378 if (error) 1379 dev_err(&pdev->dev, "%s: invalid tshut=%d, error=%d\n", 1380 __func__, thermal->tshut_temp, error); 1381 } 1382 1383 thermal->chip->control(thermal->regs, true); 1384 1385 for (i = 0; i < thermal->chip->chn_num; i++) 1386 rockchip_thermal_toggle_sensor(&thermal->sensors[i], true); 1387 1388 pinctrl_pm_select_default_state(dev); 1389 1390 return 0; 1391 } 1392 1393 static SIMPLE_DEV_PM_OPS(rockchip_thermal_pm_ops, 1394 rockchip_thermal_suspend, rockchip_thermal_resume); 1395 1396 static struct platform_driver rockchip_thermal_driver = { 1397 .driver = { 1398 .name = "rockchip-thermal", 1399 .pm = &rockchip_thermal_pm_ops, 1400 .of_match_table = of_rockchip_thermal_match, 1401 }, 1402 .probe = rockchip_thermal_probe, 1403 .remove = rockchip_thermal_remove, 1404 }; 1405 1406 module_platform_driver(rockchip_thermal_driver); 1407 1408 MODULE_DESCRIPTION("ROCKCHIP THERMAL Driver"); 1409 MODULE_AUTHOR("Rockchip, Inc."); 1410 MODULE_LICENSE("GPL v2"); 1411 MODULE_ALIAS("platform:rockchip-thermal"); 1412