1 // SPDX-License-Identifier: GPL-2.0-only 2 /* 3 * Copyright (c) 2014-2016, Fuzhou Rockchip Electronics Co., Ltd 4 * Caesar Wang <wxt@rock-chips.com> 5 */ 6 7 #include <linux/clk.h> 8 #include <linux/delay.h> 9 #include <linux/interrupt.h> 10 #include <linux/io.h> 11 #include <linux/module.h> 12 #include <linux/of.h> 13 #include <linux/of_address.h> 14 #include <linux/of_irq.h> 15 #include <linux/platform_device.h> 16 #include <linux/regmap.h> 17 #include <linux/reset.h> 18 #include <linux/thermal.h> 19 #include <linux/mfd/syscon.h> 20 #include <linux/pinctrl/consumer.h> 21 22 /* 23 * If the temperature over a period of time High, 24 * the resulting TSHUT gave CRU module,let it reset the entire chip, 25 * or via GPIO give PMIC. 26 */ 27 enum tshut_mode { 28 TSHUT_MODE_CRU = 0, 29 TSHUT_MODE_GPIO, 30 }; 31 32 /* 33 * The system Temperature Sensors tshut(tshut) polarity 34 * the bit 8 is tshut polarity. 35 * 0: low active, 1: high active 36 */ 37 enum tshut_polarity { 38 TSHUT_LOW_ACTIVE = 0, 39 TSHUT_HIGH_ACTIVE, 40 }; 41 42 /* 43 * The system has two Temperature Sensors. 44 * sensor0 is for CPU, and sensor1 is for GPU. 45 */ 46 enum sensor_id { 47 SENSOR_CPU = 0, 48 SENSOR_GPU, 49 }; 50 51 /* 52 * The conversion table has the adc value and temperature. 53 * ADC_DECREMENT: the adc value is of diminishing.(e.g. rk3288_code_table) 54 * ADC_INCREMENT: the adc value is incremental.(e.g. rk3368_code_table) 55 */ 56 enum adc_sort_mode { 57 ADC_DECREMENT = 0, 58 ADC_INCREMENT, 59 }; 60 61 #include "thermal_hwmon.h" 62 63 /** 64 * The max sensors is two in rockchip SoCs. 65 * Two sensors: CPU and GPU sensor. 66 */ 67 #define SOC_MAX_SENSORS 2 68 69 /** 70 * struct chip_tsadc_table - hold information about chip-specific differences 71 * @id: conversion table 72 * @length: size of conversion table 73 * @data_mask: mask to apply on data inputs 74 * @mode: sort mode of this adc variant (incrementing or decrementing) 75 */ 76 struct chip_tsadc_table { 77 const struct tsadc_table *id; 78 unsigned int length; 79 u32 data_mask; 80 enum adc_sort_mode mode; 81 }; 82 83 /** 84 * struct rockchip_tsadc_chip - hold the private data of tsadc chip 85 * @chn_id: array of sensor ids of chip corresponding to the channel 86 * @chn_num: the channel number of tsadc chip 87 * @tshut_temp: the hardware-controlled shutdown temperature value 88 * @tshut_mode: the hardware-controlled shutdown mode (0:CRU 1:GPIO) 89 * @tshut_polarity: the hardware-controlled active polarity (0:LOW 1:HIGH) 90 * @initialize: SoC special initialize tsadc controller method 91 * @irq_ack: clear the interrupt 92 * @control: enable/disable method for the tsadc controller 93 * @get_temp: get the temperature 94 * @set_alarm_temp: set the high temperature interrupt 95 * @set_tshut_temp: set the hardware-controlled shutdown temperature 96 * @set_tshut_mode: set the hardware-controlled shutdown mode 97 * @table: the chip-specific conversion table 98 */ 99 struct rockchip_tsadc_chip { 100 /* The sensor id of chip correspond to the ADC channel */ 101 int chn_id[SOC_MAX_SENSORS]; 102 int chn_num; 103 104 /* The hardware-controlled tshut property */ 105 int tshut_temp; 106 enum tshut_mode tshut_mode; 107 enum tshut_polarity tshut_polarity; 108 109 /* Chip-wide methods */ 110 void (*initialize)(struct regmap *grf, 111 void __iomem *reg, enum tshut_polarity p); 112 void (*irq_ack)(void __iomem *reg); 113 void (*control)(void __iomem *reg, bool on); 114 115 /* Per-sensor methods */ 116 int (*get_temp)(const struct chip_tsadc_table *table, 117 int chn, void __iomem *reg, int *temp); 118 int (*set_alarm_temp)(const struct chip_tsadc_table *table, 119 int chn, void __iomem *reg, int temp); 120 int (*set_tshut_temp)(const struct chip_tsadc_table *table, 121 int chn, void __iomem *reg, int temp); 122 void (*set_tshut_mode)(int chn, void __iomem *reg, enum tshut_mode m); 123 124 /* Per-table methods */ 125 struct chip_tsadc_table table; 126 }; 127 128 /** 129 * struct rockchip_thermal_sensor - hold the information of thermal sensor 130 * @thermal: pointer to the platform/configuration data 131 * @tzd: pointer to a thermal zone 132 * @id: identifier of the thermal sensor 133 */ 134 struct rockchip_thermal_sensor { 135 struct rockchip_thermal_data *thermal; 136 struct thermal_zone_device *tzd; 137 int id; 138 }; 139 140 /** 141 * struct rockchip_thermal_data - hold the private data of thermal driver 142 * @chip: pointer to the platform/configuration data 143 * @pdev: platform device of thermal 144 * @reset: the reset controller of tsadc 145 * @sensors: array of thermal sensors 146 * @clk: the controller clock is divided by the exteral 24MHz 147 * @pclk: the advanced peripherals bus clock 148 * @grf: the general register file will be used to do static set by software 149 * @regs: the base address of tsadc controller 150 * @tshut_temp: the hardware-controlled shutdown temperature value 151 * @tshut_mode: the hardware-controlled shutdown mode (0:CRU 1:GPIO) 152 * @tshut_polarity: the hardware-controlled active polarity (0:LOW 1:HIGH) 153 */ 154 struct rockchip_thermal_data { 155 const struct rockchip_tsadc_chip *chip; 156 struct platform_device *pdev; 157 struct reset_control *reset; 158 159 struct rockchip_thermal_sensor sensors[SOC_MAX_SENSORS]; 160 161 struct clk *clk; 162 struct clk *pclk; 163 164 struct regmap *grf; 165 void __iomem *regs; 166 167 int tshut_temp; 168 enum tshut_mode tshut_mode; 169 enum tshut_polarity tshut_polarity; 170 }; 171 172 /** 173 * TSADC Sensor Register description: 174 * 175 * TSADCV2_* are used for RK3288 SoCs, the other chips can reuse it. 176 * TSADCV3_* are used for newer SoCs than RK3288. (e.g: RK3228, RK3399) 177 * 178 */ 179 #define TSADCV2_USER_CON 0x00 180 #define TSADCV2_AUTO_CON 0x04 181 #define TSADCV2_INT_EN 0x08 182 #define TSADCV2_INT_PD 0x0c 183 #define TSADCV2_DATA(chn) (0x20 + (chn) * 0x04) 184 #define TSADCV2_COMP_INT(chn) (0x30 + (chn) * 0x04) 185 #define TSADCV2_COMP_SHUT(chn) (0x40 + (chn) * 0x04) 186 #define TSADCV2_HIGHT_INT_DEBOUNCE 0x60 187 #define TSADCV2_HIGHT_TSHUT_DEBOUNCE 0x64 188 #define TSADCV2_AUTO_PERIOD 0x68 189 #define TSADCV2_AUTO_PERIOD_HT 0x6c 190 191 #define TSADCV2_AUTO_EN BIT(0) 192 #define TSADCV2_AUTO_SRC_EN(chn) BIT(4 + (chn)) 193 #define TSADCV2_AUTO_TSHUT_POLARITY_HIGH BIT(8) 194 195 #define TSADCV3_AUTO_Q_SEL_EN BIT(1) 196 197 #define TSADCV2_INT_SRC_EN(chn) BIT(chn) 198 #define TSADCV2_SHUT_2GPIO_SRC_EN(chn) BIT(4 + (chn)) 199 #define TSADCV2_SHUT_2CRU_SRC_EN(chn) BIT(8 + (chn)) 200 201 #define TSADCV2_INT_PD_CLEAR_MASK ~BIT(8) 202 #define TSADCV3_INT_PD_CLEAR_MASK ~BIT(16) 203 204 #define TSADCV2_DATA_MASK 0xfff 205 #define TSADCV3_DATA_MASK 0x3ff 206 207 #define TSADCV2_HIGHT_INT_DEBOUNCE_COUNT 4 208 #define TSADCV2_HIGHT_TSHUT_DEBOUNCE_COUNT 4 209 #define TSADCV2_AUTO_PERIOD_TIME 250 /* 250ms */ 210 #define TSADCV2_AUTO_PERIOD_HT_TIME 50 /* 50ms */ 211 #define TSADCV3_AUTO_PERIOD_TIME 1875 /* 2.5ms */ 212 #define TSADCV3_AUTO_PERIOD_HT_TIME 1875 /* 2.5ms */ 213 214 #define TSADCV5_AUTO_PERIOD_TIME 1622 /* 2.5ms */ 215 #define TSADCV5_AUTO_PERIOD_HT_TIME 1622 /* 2.5ms */ 216 217 #define TSADCV2_USER_INTER_PD_SOC 0x340 /* 13 clocks */ 218 #define TSADCV5_USER_INTER_PD_SOC 0xfc0 /* 97us, at least 90us */ 219 220 #define GRF_SARADC_TESTBIT 0x0e644 221 #define GRF_TSADC_TESTBIT_L 0x0e648 222 #define GRF_TSADC_TESTBIT_H 0x0e64c 223 224 #define PX30_GRF_SOC_CON2 0x0408 225 226 #define RK3568_GRF_TSADC_CON 0x0600 227 #define RK3568_GRF_TSADC_ANA_REG0 (0x10001 << 0) 228 #define RK3568_GRF_TSADC_ANA_REG1 (0x10001 << 1) 229 #define RK3568_GRF_TSADC_ANA_REG2 (0x10001 << 2) 230 #define RK3568_GRF_TSADC_TSEN (0x10001 << 8) 231 232 #define GRF_SARADC_TESTBIT_ON (0x10001 << 2) 233 #define GRF_TSADC_TESTBIT_H_ON (0x10001 << 2) 234 #define GRF_TSADC_VCM_EN_L (0x10001 << 7) 235 #define GRF_TSADC_VCM_EN_H (0x10001 << 7) 236 237 #define GRF_CON_TSADC_CH_INV (0x10001 << 1) 238 239 /** 240 * struct tsadc_table - code to temperature conversion table 241 * @code: the value of adc channel 242 * @temp: the temperature 243 * Note: 244 * code to temperature mapping of the temperature sensor is a piece wise linear 245 * curve.Any temperature, code faling between to 2 give temperatures can be 246 * linearly interpolated. 247 * Code to Temperature mapping should be updated based on manufacturer results. 248 */ 249 struct tsadc_table { 250 u32 code; 251 int temp; 252 }; 253 254 static const struct tsadc_table rv1108_table[] = { 255 {0, -40000}, 256 {374, -40000}, 257 {382, -35000}, 258 {389, -30000}, 259 {397, -25000}, 260 {405, -20000}, 261 {413, -15000}, 262 {421, -10000}, 263 {429, -5000}, 264 {436, 0}, 265 {444, 5000}, 266 {452, 10000}, 267 {460, 15000}, 268 {468, 20000}, 269 {476, 25000}, 270 {483, 30000}, 271 {491, 35000}, 272 {499, 40000}, 273 {507, 45000}, 274 {515, 50000}, 275 {523, 55000}, 276 {531, 60000}, 277 {539, 65000}, 278 {547, 70000}, 279 {555, 75000}, 280 {562, 80000}, 281 {570, 85000}, 282 {578, 90000}, 283 {586, 95000}, 284 {594, 100000}, 285 {602, 105000}, 286 {610, 110000}, 287 {618, 115000}, 288 {626, 120000}, 289 {634, 125000}, 290 {TSADCV2_DATA_MASK, 125000}, 291 }; 292 293 static const struct tsadc_table rk3228_code_table[] = { 294 {0, -40000}, 295 {588, -40000}, 296 {593, -35000}, 297 {598, -30000}, 298 {603, -25000}, 299 {608, -20000}, 300 {613, -15000}, 301 {618, -10000}, 302 {623, -5000}, 303 {629, 0}, 304 {634, 5000}, 305 {639, 10000}, 306 {644, 15000}, 307 {649, 20000}, 308 {654, 25000}, 309 {660, 30000}, 310 {665, 35000}, 311 {670, 40000}, 312 {675, 45000}, 313 {681, 50000}, 314 {686, 55000}, 315 {691, 60000}, 316 {696, 65000}, 317 {702, 70000}, 318 {707, 75000}, 319 {712, 80000}, 320 {717, 85000}, 321 {723, 90000}, 322 {728, 95000}, 323 {733, 100000}, 324 {738, 105000}, 325 {744, 110000}, 326 {749, 115000}, 327 {754, 120000}, 328 {760, 125000}, 329 {TSADCV2_DATA_MASK, 125000}, 330 }; 331 332 static const struct tsadc_table rk3288_code_table[] = { 333 {TSADCV2_DATA_MASK, -40000}, 334 {3800, -40000}, 335 {3792, -35000}, 336 {3783, -30000}, 337 {3774, -25000}, 338 {3765, -20000}, 339 {3756, -15000}, 340 {3747, -10000}, 341 {3737, -5000}, 342 {3728, 0}, 343 {3718, 5000}, 344 {3708, 10000}, 345 {3698, 15000}, 346 {3688, 20000}, 347 {3678, 25000}, 348 {3667, 30000}, 349 {3656, 35000}, 350 {3645, 40000}, 351 {3634, 45000}, 352 {3623, 50000}, 353 {3611, 55000}, 354 {3600, 60000}, 355 {3588, 65000}, 356 {3575, 70000}, 357 {3563, 75000}, 358 {3550, 80000}, 359 {3537, 85000}, 360 {3524, 90000}, 361 {3510, 95000}, 362 {3496, 100000}, 363 {3482, 105000}, 364 {3467, 110000}, 365 {3452, 115000}, 366 {3437, 120000}, 367 {3421, 125000}, 368 {0, 125000}, 369 }; 370 371 static const struct tsadc_table rk3328_code_table[] = { 372 {0, -40000}, 373 {296, -40000}, 374 {304, -35000}, 375 {313, -30000}, 376 {331, -20000}, 377 {340, -15000}, 378 {349, -10000}, 379 {359, -5000}, 380 {368, 0}, 381 {378, 5000}, 382 {388, 10000}, 383 {398, 15000}, 384 {408, 20000}, 385 {418, 25000}, 386 {429, 30000}, 387 {440, 35000}, 388 {451, 40000}, 389 {462, 45000}, 390 {473, 50000}, 391 {485, 55000}, 392 {496, 60000}, 393 {508, 65000}, 394 {521, 70000}, 395 {533, 75000}, 396 {546, 80000}, 397 {559, 85000}, 398 {572, 90000}, 399 {586, 95000}, 400 {600, 100000}, 401 {614, 105000}, 402 {629, 110000}, 403 {644, 115000}, 404 {659, 120000}, 405 {675, 125000}, 406 {TSADCV2_DATA_MASK, 125000}, 407 }; 408 409 static const struct tsadc_table rk3368_code_table[] = { 410 {0, -40000}, 411 {106, -40000}, 412 {108, -35000}, 413 {110, -30000}, 414 {112, -25000}, 415 {114, -20000}, 416 {116, -15000}, 417 {118, -10000}, 418 {120, -5000}, 419 {122, 0}, 420 {124, 5000}, 421 {126, 10000}, 422 {128, 15000}, 423 {130, 20000}, 424 {132, 25000}, 425 {134, 30000}, 426 {136, 35000}, 427 {138, 40000}, 428 {140, 45000}, 429 {142, 50000}, 430 {144, 55000}, 431 {146, 60000}, 432 {148, 65000}, 433 {150, 70000}, 434 {152, 75000}, 435 {154, 80000}, 436 {156, 85000}, 437 {158, 90000}, 438 {160, 95000}, 439 {162, 100000}, 440 {163, 105000}, 441 {165, 110000}, 442 {167, 115000}, 443 {169, 120000}, 444 {171, 125000}, 445 {TSADCV3_DATA_MASK, 125000}, 446 }; 447 448 static const struct tsadc_table rk3399_code_table[] = { 449 {0, -40000}, 450 {402, -40000}, 451 {410, -35000}, 452 {419, -30000}, 453 {427, -25000}, 454 {436, -20000}, 455 {444, -15000}, 456 {453, -10000}, 457 {461, -5000}, 458 {470, 0}, 459 {478, 5000}, 460 {487, 10000}, 461 {496, 15000}, 462 {504, 20000}, 463 {513, 25000}, 464 {521, 30000}, 465 {530, 35000}, 466 {538, 40000}, 467 {547, 45000}, 468 {555, 50000}, 469 {564, 55000}, 470 {573, 60000}, 471 {581, 65000}, 472 {590, 70000}, 473 {599, 75000}, 474 {607, 80000}, 475 {616, 85000}, 476 {624, 90000}, 477 {633, 95000}, 478 {642, 100000}, 479 {650, 105000}, 480 {659, 110000}, 481 {668, 115000}, 482 {677, 120000}, 483 {685, 125000}, 484 {TSADCV3_DATA_MASK, 125000}, 485 }; 486 487 static const struct tsadc_table rk3568_code_table[] = { 488 {0, -40000}, 489 {1584, -40000}, 490 {1620, -35000}, 491 {1652, -30000}, 492 {1688, -25000}, 493 {1720, -20000}, 494 {1756, -15000}, 495 {1788, -10000}, 496 {1824, -5000}, 497 {1856, 0}, 498 {1892, 5000}, 499 {1924, 10000}, 500 {1956, 15000}, 501 {1992, 20000}, 502 {2024, 25000}, 503 {2060, 30000}, 504 {2092, 35000}, 505 {2128, 40000}, 506 {2160, 45000}, 507 {2196, 50000}, 508 {2228, 55000}, 509 {2264, 60000}, 510 {2300, 65000}, 511 {2332, 70000}, 512 {2368, 75000}, 513 {2400, 80000}, 514 {2436, 85000}, 515 {2468, 90000}, 516 {2500, 95000}, 517 {2536, 100000}, 518 {2572, 105000}, 519 {2604, 110000}, 520 {2636, 115000}, 521 {2672, 120000}, 522 {2704, 125000}, 523 {TSADCV2_DATA_MASK, 125000}, 524 }; 525 526 static u32 rk_tsadcv2_temp_to_code(const struct chip_tsadc_table *table, 527 int temp) 528 { 529 int high, low, mid; 530 unsigned long num; 531 unsigned int denom; 532 u32 error = table->data_mask; 533 534 low = 0; 535 high = (table->length - 1) - 1; /* ignore the last check for table */ 536 mid = (high + low) / 2; 537 538 /* Return mask code data when the temp is over table range */ 539 if (temp < table->id[low].temp || temp > table->id[high].temp) 540 goto exit; 541 542 while (low <= high) { 543 if (temp == table->id[mid].temp) 544 return table->id[mid].code; 545 else if (temp < table->id[mid].temp) 546 high = mid - 1; 547 else 548 low = mid + 1; 549 mid = (low + high) / 2; 550 } 551 552 /* 553 * The conversion code granularity provided by the table. Let's 554 * assume that the relationship between temperature and 555 * analog value between 2 table entries is linear and interpolate 556 * to produce less granular result. 557 */ 558 num = abs(table->id[mid + 1].code - table->id[mid].code); 559 num *= temp - table->id[mid].temp; 560 denom = table->id[mid + 1].temp - table->id[mid].temp; 561 562 switch (table->mode) { 563 case ADC_DECREMENT: 564 return table->id[mid].code - (num / denom); 565 case ADC_INCREMENT: 566 return table->id[mid].code + (num / denom); 567 default: 568 pr_err("%s: unknown table mode: %d\n", __func__, table->mode); 569 return error; 570 } 571 572 exit: 573 pr_err("%s: invalid temperature, temp=%d error=%d\n", 574 __func__, temp, error); 575 return error; 576 } 577 578 static int rk_tsadcv2_code_to_temp(const struct chip_tsadc_table *table, 579 u32 code, int *temp) 580 { 581 unsigned int low = 1; 582 unsigned int high = table->length - 1; 583 unsigned int mid = (low + high) / 2; 584 unsigned int num; 585 unsigned long denom; 586 587 WARN_ON(table->length < 2); 588 589 switch (table->mode) { 590 case ADC_DECREMENT: 591 code &= table->data_mask; 592 if (code <= table->id[high].code) 593 return -EAGAIN; /* Incorrect reading */ 594 595 while (low <= high) { 596 if (code >= table->id[mid].code && 597 code < table->id[mid - 1].code) 598 break; 599 else if (code < table->id[mid].code) 600 low = mid + 1; 601 else 602 high = mid - 1; 603 604 mid = (low + high) / 2; 605 } 606 break; 607 case ADC_INCREMENT: 608 code &= table->data_mask; 609 if (code < table->id[low].code) 610 return -EAGAIN; /* Incorrect reading */ 611 612 while (low <= high) { 613 if (code <= table->id[mid].code && 614 code > table->id[mid - 1].code) 615 break; 616 else if (code > table->id[mid].code) 617 low = mid + 1; 618 else 619 high = mid - 1; 620 621 mid = (low + high) / 2; 622 } 623 break; 624 default: 625 pr_err("%s: unknown table mode: %d\n", __func__, table->mode); 626 return -EINVAL; 627 } 628 629 /* 630 * The 5C granularity provided by the table is too much. Let's 631 * assume that the relationship between sensor readings and 632 * temperature between 2 table entries is linear and interpolate 633 * to produce less granular result. 634 */ 635 num = table->id[mid].temp - table->id[mid - 1].temp; 636 num *= abs(table->id[mid - 1].code - code); 637 denom = abs(table->id[mid - 1].code - table->id[mid].code); 638 *temp = table->id[mid - 1].temp + (num / denom); 639 640 return 0; 641 } 642 643 /** 644 * rk_tsadcv2_initialize - initialize TASDC Controller. 645 * @grf: the general register file will be used to do static set by software 646 * @regs: the base address of tsadc controller 647 * @tshut_polarity: the hardware-controlled active polarity (0:LOW 1:HIGH) 648 * 649 * (1) Set TSADC_V2_AUTO_PERIOD: 650 * Configure the interleave between every two accessing of 651 * TSADC in normal operation. 652 * 653 * (2) Set TSADCV2_AUTO_PERIOD_HT: 654 * Configure the interleave between every two accessing of 655 * TSADC after the temperature is higher than COM_SHUT or COM_INT. 656 * 657 * (3) Set TSADCV2_HIGH_INT_DEBOUNCE and TSADC_HIGHT_TSHUT_DEBOUNCE: 658 * If the temperature is higher than COMP_INT or COMP_SHUT for 659 * "debounce" times, TSADC controller will generate interrupt or TSHUT. 660 */ 661 static void rk_tsadcv2_initialize(struct regmap *grf, void __iomem *regs, 662 enum tshut_polarity tshut_polarity) 663 { 664 if (tshut_polarity == TSHUT_HIGH_ACTIVE) 665 writel_relaxed(0U | TSADCV2_AUTO_TSHUT_POLARITY_HIGH, 666 regs + TSADCV2_AUTO_CON); 667 else 668 writel_relaxed(0U & ~TSADCV2_AUTO_TSHUT_POLARITY_HIGH, 669 regs + TSADCV2_AUTO_CON); 670 671 writel_relaxed(TSADCV2_AUTO_PERIOD_TIME, regs + TSADCV2_AUTO_PERIOD); 672 writel_relaxed(TSADCV2_HIGHT_INT_DEBOUNCE_COUNT, 673 regs + TSADCV2_HIGHT_INT_DEBOUNCE); 674 writel_relaxed(TSADCV2_AUTO_PERIOD_HT_TIME, 675 regs + TSADCV2_AUTO_PERIOD_HT); 676 writel_relaxed(TSADCV2_HIGHT_TSHUT_DEBOUNCE_COUNT, 677 regs + TSADCV2_HIGHT_TSHUT_DEBOUNCE); 678 } 679 680 /** 681 * rk_tsadcv3_initialize - initialize TASDC Controller. 682 * @grf: the general register file will be used to do static set by software 683 * @regs: the base address of tsadc controller 684 * @tshut_polarity: the hardware-controlled active polarity (0:LOW 1:HIGH) 685 * 686 * (1) The tsadc control power sequence. 687 * 688 * (2) Set TSADC_V2_AUTO_PERIOD: 689 * Configure the interleave between every two accessing of 690 * TSADC in normal operation. 691 * 692 * (2) Set TSADCV2_AUTO_PERIOD_HT: 693 * Configure the interleave between every two accessing of 694 * TSADC after the temperature is higher than COM_SHUT or COM_INT. 695 * 696 * (3) Set TSADCV2_HIGH_INT_DEBOUNCE and TSADC_HIGHT_TSHUT_DEBOUNCE: 697 * If the temperature is higher than COMP_INT or COMP_SHUT for 698 * "debounce" times, TSADC controller will generate interrupt or TSHUT. 699 */ 700 static void rk_tsadcv3_initialize(struct regmap *grf, void __iomem *regs, 701 enum tshut_polarity tshut_polarity) 702 { 703 /* The tsadc control power sequence */ 704 if (IS_ERR(grf)) { 705 /* Set interleave value to workround ic time sync issue */ 706 writel_relaxed(TSADCV2_USER_INTER_PD_SOC, regs + 707 TSADCV2_USER_CON); 708 709 writel_relaxed(TSADCV2_AUTO_PERIOD_TIME, 710 regs + TSADCV2_AUTO_PERIOD); 711 writel_relaxed(TSADCV2_HIGHT_INT_DEBOUNCE_COUNT, 712 regs + TSADCV2_HIGHT_INT_DEBOUNCE); 713 writel_relaxed(TSADCV2_AUTO_PERIOD_HT_TIME, 714 regs + TSADCV2_AUTO_PERIOD_HT); 715 writel_relaxed(TSADCV2_HIGHT_TSHUT_DEBOUNCE_COUNT, 716 regs + TSADCV2_HIGHT_TSHUT_DEBOUNCE); 717 718 } else { 719 /* Enable the voltage common mode feature */ 720 regmap_write(grf, GRF_TSADC_TESTBIT_L, GRF_TSADC_VCM_EN_L); 721 regmap_write(grf, GRF_TSADC_TESTBIT_H, GRF_TSADC_VCM_EN_H); 722 723 usleep_range(15, 100); /* The spec note says at least 15 us */ 724 regmap_write(grf, GRF_SARADC_TESTBIT, GRF_SARADC_TESTBIT_ON); 725 regmap_write(grf, GRF_TSADC_TESTBIT_H, GRF_TSADC_TESTBIT_H_ON); 726 usleep_range(90, 200); /* The spec note says at least 90 us */ 727 728 writel_relaxed(TSADCV3_AUTO_PERIOD_TIME, 729 regs + TSADCV2_AUTO_PERIOD); 730 writel_relaxed(TSADCV2_HIGHT_INT_DEBOUNCE_COUNT, 731 regs + TSADCV2_HIGHT_INT_DEBOUNCE); 732 writel_relaxed(TSADCV3_AUTO_PERIOD_HT_TIME, 733 regs + TSADCV2_AUTO_PERIOD_HT); 734 writel_relaxed(TSADCV2_HIGHT_TSHUT_DEBOUNCE_COUNT, 735 regs + TSADCV2_HIGHT_TSHUT_DEBOUNCE); 736 } 737 738 if (tshut_polarity == TSHUT_HIGH_ACTIVE) 739 writel_relaxed(0U | TSADCV2_AUTO_TSHUT_POLARITY_HIGH, 740 regs + TSADCV2_AUTO_CON); 741 else 742 writel_relaxed(0U & ~TSADCV2_AUTO_TSHUT_POLARITY_HIGH, 743 regs + TSADCV2_AUTO_CON); 744 } 745 746 static void rk_tsadcv4_initialize(struct regmap *grf, void __iomem *regs, 747 enum tshut_polarity tshut_polarity) 748 { 749 rk_tsadcv2_initialize(grf, regs, tshut_polarity); 750 regmap_write(grf, PX30_GRF_SOC_CON2, GRF_CON_TSADC_CH_INV); 751 } 752 753 static void rk_tsadcv7_initialize(struct regmap *grf, void __iomem *regs, 754 enum tshut_polarity tshut_polarity) 755 { 756 writel_relaxed(TSADCV5_USER_INTER_PD_SOC, regs + TSADCV2_USER_CON); 757 writel_relaxed(TSADCV5_AUTO_PERIOD_TIME, regs + TSADCV2_AUTO_PERIOD); 758 writel_relaxed(TSADCV2_HIGHT_INT_DEBOUNCE_COUNT, 759 regs + TSADCV2_HIGHT_INT_DEBOUNCE); 760 writel_relaxed(TSADCV5_AUTO_PERIOD_HT_TIME, 761 regs + TSADCV2_AUTO_PERIOD_HT); 762 writel_relaxed(TSADCV2_HIGHT_TSHUT_DEBOUNCE_COUNT, 763 regs + TSADCV2_HIGHT_TSHUT_DEBOUNCE); 764 765 if (tshut_polarity == TSHUT_HIGH_ACTIVE) 766 writel_relaxed(0U | TSADCV2_AUTO_TSHUT_POLARITY_HIGH, 767 regs + TSADCV2_AUTO_CON); 768 else 769 writel_relaxed(0U & ~TSADCV2_AUTO_TSHUT_POLARITY_HIGH, 770 regs + TSADCV2_AUTO_CON); 771 772 /* 773 * The general register file will is optional 774 * and might not be available. 775 */ 776 if (!IS_ERR(grf)) { 777 regmap_write(grf, RK3568_GRF_TSADC_CON, RK3568_GRF_TSADC_TSEN); 778 /* 779 * RK3568 TRM, section 18.5. requires a delay no less 780 * than 10us between the rising edge of tsadc_tsen_en 781 * and the rising edge of tsadc_ana_reg_0/1/2. 782 */ 783 udelay(15); 784 regmap_write(grf, RK3568_GRF_TSADC_CON, RK3568_GRF_TSADC_ANA_REG0); 785 regmap_write(grf, RK3568_GRF_TSADC_CON, RK3568_GRF_TSADC_ANA_REG1); 786 regmap_write(grf, RK3568_GRF_TSADC_CON, RK3568_GRF_TSADC_ANA_REG2); 787 788 /* 789 * RK3568 TRM, section 18.5. requires a delay no less 790 * than 90us after the rising edge of tsadc_ana_reg_0/1/2. 791 */ 792 usleep_range(100, 200); 793 } 794 } 795 796 static void rk_tsadcv2_irq_ack(void __iomem *regs) 797 { 798 u32 val; 799 800 val = readl_relaxed(regs + TSADCV2_INT_PD); 801 writel_relaxed(val & TSADCV2_INT_PD_CLEAR_MASK, regs + TSADCV2_INT_PD); 802 } 803 804 static void rk_tsadcv3_irq_ack(void __iomem *regs) 805 { 806 u32 val; 807 808 val = readl_relaxed(regs + TSADCV2_INT_PD); 809 writel_relaxed(val & TSADCV3_INT_PD_CLEAR_MASK, regs + TSADCV2_INT_PD); 810 } 811 812 static void rk_tsadcv2_control(void __iomem *regs, bool enable) 813 { 814 u32 val; 815 816 val = readl_relaxed(regs + TSADCV2_AUTO_CON); 817 if (enable) 818 val |= TSADCV2_AUTO_EN; 819 else 820 val &= ~TSADCV2_AUTO_EN; 821 822 writel_relaxed(val, regs + TSADCV2_AUTO_CON); 823 } 824 825 /** 826 * rk_tsadcv3_control - the tsadc controller is enabled or disabled. 827 * @regs: the base address of tsadc controller 828 * @enable: boolean flag to enable the controller 829 * 830 * NOTE: TSADC controller works at auto mode, and some SoCs need set the 831 * tsadc_q_sel bit on TSADCV2_AUTO_CON[1]. The (1024 - tsadc_q) as output 832 * adc value if setting this bit to enable. 833 */ 834 static void rk_tsadcv3_control(void __iomem *regs, bool enable) 835 { 836 u32 val; 837 838 val = readl_relaxed(regs + TSADCV2_AUTO_CON); 839 if (enable) 840 val |= TSADCV2_AUTO_EN | TSADCV3_AUTO_Q_SEL_EN; 841 else 842 val &= ~TSADCV2_AUTO_EN; 843 844 writel_relaxed(val, regs + TSADCV2_AUTO_CON); 845 } 846 847 static int rk_tsadcv2_get_temp(const struct chip_tsadc_table *table, 848 int chn, void __iomem *regs, int *temp) 849 { 850 u32 val; 851 852 val = readl_relaxed(regs + TSADCV2_DATA(chn)); 853 854 return rk_tsadcv2_code_to_temp(table, val, temp); 855 } 856 857 static int rk_tsadcv2_alarm_temp(const struct chip_tsadc_table *table, 858 int chn, void __iomem *regs, int temp) 859 { 860 u32 alarm_value; 861 u32 int_en, int_clr; 862 863 /* 864 * In some cases, some sensors didn't need the trip points, the 865 * set_trips will pass {-INT_MAX, INT_MAX} to trigger tsadc alarm 866 * in the end, ignore this case and disable the high temperature 867 * interrupt. 868 */ 869 if (temp == INT_MAX) { 870 int_clr = readl_relaxed(regs + TSADCV2_INT_EN); 871 int_clr &= ~TSADCV2_INT_SRC_EN(chn); 872 writel_relaxed(int_clr, regs + TSADCV2_INT_EN); 873 return 0; 874 } 875 876 /* Make sure the value is valid */ 877 alarm_value = rk_tsadcv2_temp_to_code(table, temp); 878 if (alarm_value == table->data_mask) 879 return -ERANGE; 880 881 writel_relaxed(alarm_value & table->data_mask, 882 regs + TSADCV2_COMP_INT(chn)); 883 884 int_en = readl_relaxed(regs + TSADCV2_INT_EN); 885 int_en |= TSADCV2_INT_SRC_EN(chn); 886 writel_relaxed(int_en, regs + TSADCV2_INT_EN); 887 888 return 0; 889 } 890 891 static int rk_tsadcv2_tshut_temp(const struct chip_tsadc_table *table, 892 int chn, void __iomem *regs, int temp) 893 { 894 u32 tshut_value, val; 895 896 /* Make sure the value is valid */ 897 tshut_value = rk_tsadcv2_temp_to_code(table, temp); 898 if (tshut_value == table->data_mask) 899 return -ERANGE; 900 901 writel_relaxed(tshut_value, regs + TSADCV2_COMP_SHUT(chn)); 902 903 /* TSHUT will be valid */ 904 val = readl_relaxed(regs + TSADCV2_AUTO_CON); 905 writel_relaxed(val | TSADCV2_AUTO_SRC_EN(chn), regs + TSADCV2_AUTO_CON); 906 907 return 0; 908 } 909 910 static void rk_tsadcv2_tshut_mode(int chn, void __iomem *regs, 911 enum tshut_mode mode) 912 { 913 u32 val; 914 915 val = readl_relaxed(regs + TSADCV2_INT_EN); 916 if (mode == TSHUT_MODE_GPIO) { 917 val &= ~TSADCV2_SHUT_2CRU_SRC_EN(chn); 918 val |= TSADCV2_SHUT_2GPIO_SRC_EN(chn); 919 } else { 920 val &= ~TSADCV2_SHUT_2GPIO_SRC_EN(chn); 921 val |= TSADCV2_SHUT_2CRU_SRC_EN(chn); 922 } 923 924 writel_relaxed(val, regs + TSADCV2_INT_EN); 925 } 926 927 static const struct rockchip_tsadc_chip px30_tsadc_data = { 928 .chn_id[SENSOR_CPU] = 0, /* cpu sensor is channel 0 */ 929 .chn_id[SENSOR_GPU] = 1, /* gpu sensor is channel 1 */ 930 .chn_num = 2, /* 2 channels for tsadc */ 931 932 .tshut_mode = TSHUT_MODE_CRU, /* default TSHUT via CRU */ 933 .tshut_temp = 95000, 934 935 .initialize = rk_tsadcv4_initialize, 936 .irq_ack = rk_tsadcv3_irq_ack, 937 .control = rk_tsadcv3_control, 938 .get_temp = rk_tsadcv2_get_temp, 939 .set_alarm_temp = rk_tsadcv2_alarm_temp, 940 .set_tshut_temp = rk_tsadcv2_tshut_temp, 941 .set_tshut_mode = rk_tsadcv2_tshut_mode, 942 943 .table = { 944 .id = rk3328_code_table, 945 .length = ARRAY_SIZE(rk3328_code_table), 946 .data_mask = TSADCV2_DATA_MASK, 947 .mode = ADC_INCREMENT, 948 }, 949 }; 950 951 static const struct rockchip_tsadc_chip rv1108_tsadc_data = { 952 .chn_id[SENSOR_CPU] = 0, /* cpu sensor is channel 0 */ 953 .chn_num = 1, /* one channel for tsadc */ 954 955 .tshut_mode = TSHUT_MODE_GPIO, /* default TSHUT via GPIO give PMIC */ 956 .tshut_polarity = TSHUT_LOW_ACTIVE, /* default TSHUT LOW ACTIVE */ 957 .tshut_temp = 95000, 958 959 .initialize = rk_tsadcv2_initialize, 960 .irq_ack = rk_tsadcv3_irq_ack, 961 .control = rk_tsadcv3_control, 962 .get_temp = rk_tsadcv2_get_temp, 963 .set_alarm_temp = rk_tsadcv2_alarm_temp, 964 .set_tshut_temp = rk_tsadcv2_tshut_temp, 965 .set_tshut_mode = rk_tsadcv2_tshut_mode, 966 967 .table = { 968 .id = rv1108_table, 969 .length = ARRAY_SIZE(rv1108_table), 970 .data_mask = TSADCV2_DATA_MASK, 971 .mode = ADC_INCREMENT, 972 }, 973 }; 974 975 static const struct rockchip_tsadc_chip rk3228_tsadc_data = { 976 .chn_id[SENSOR_CPU] = 0, /* cpu sensor is channel 0 */ 977 .chn_num = 1, /* one channel for tsadc */ 978 979 .tshut_mode = TSHUT_MODE_GPIO, /* default TSHUT via GPIO give PMIC */ 980 .tshut_polarity = TSHUT_LOW_ACTIVE, /* default TSHUT LOW ACTIVE */ 981 .tshut_temp = 95000, 982 983 .initialize = rk_tsadcv2_initialize, 984 .irq_ack = rk_tsadcv3_irq_ack, 985 .control = rk_tsadcv3_control, 986 .get_temp = rk_tsadcv2_get_temp, 987 .set_alarm_temp = rk_tsadcv2_alarm_temp, 988 .set_tshut_temp = rk_tsadcv2_tshut_temp, 989 .set_tshut_mode = rk_tsadcv2_tshut_mode, 990 991 .table = { 992 .id = rk3228_code_table, 993 .length = ARRAY_SIZE(rk3228_code_table), 994 .data_mask = TSADCV3_DATA_MASK, 995 .mode = ADC_INCREMENT, 996 }, 997 }; 998 999 static const struct rockchip_tsadc_chip rk3288_tsadc_data = { 1000 .chn_id[SENSOR_CPU] = 1, /* cpu sensor is channel 1 */ 1001 .chn_id[SENSOR_GPU] = 2, /* gpu sensor is channel 2 */ 1002 .chn_num = 2, /* two channels for tsadc */ 1003 1004 .tshut_mode = TSHUT_MODE_GPIO, /* default TSHUT via GPIO give PMIC */ 1005 .tshut_polarity = TSHUT_LOW_ACTIVE, /* default TSHUT LOW ACTIVE */ 1006 .tshut_temp = 95000, 1007 1008 .initialize = rk_tsadcv2_initialize, 1009 .irq_ack = rk_tsadcv2_irq_ack, 1010 .control = rk_tsadcv2_control, 1011 .get_temp = rk_tsadcv2_get_temp, 1012 .set_alarm_temp = rk_tsadcv2_alarm_temp, 1013 .set_tshut_temp = rk_tsadcv2_tshut_temp, 1014 .set_tshut_mode = rk_tsadcv2_tshut_mode, 1015 1016 .table = { 1017 .id = rk3288_code_table, 1018 .length = ARRAY_SIZE(rk3288_code_table), 1019 .data_mask = TSADCV2_DATA_MASK, 1020 .mode = ADC_DECREMENT, 1021 }, 1022 }; 1023 1024 static const struct rockchip_tsadc_chip rk3328_tsadc_data = { 1025 .chn_id[SENSOR_CPU] = 0, /* cpu sensor is channel 0 */ 1026 .chn_num = 1, /* one channels for tsadc */ 1027 1028 .tshut_mode = TSHUT_MODE_CRU, /* default TSHUT via CRU */ 1029 .tshut_temp = 95000, 1030 1031 .initialize = rk_tsadcv2_initialize, 1032 .irq_ack = rk_tsadcv3_irq_ack, 1033 .control = rk_tsadcv3_control, 1034 .get_temp = rk_tsadcv2_get_temp, 1035 .set_alarm_temp = rk_tsadcv2_alarm_temp, 1036 .set_tshut_temp = rk_tsadcv2_tshut_temp, 1037 .set_tshut_mode = rk_tsadcv2_tshut_mode, 1038 1039 .table = { 1040 .id = rk3328_code_table, 1041 .length = ARRAY_SIZE(rk3328_code_table), 1042 .data_mask = TSADCV2_DATA_MASK, 1043 .mode = ADC_INCREMENT, 1044 }, 1045 }; 1046 1047 static const struct rockchip_tsadc_chip rk3366_tsadc_data = { 1048 .chn_id[SENSOR_CPU] = 0, /* cpu sensor is channel 0 */ 1049 .chn_id[SENSOR_GPU] = 1, /* gpu sensor is channel 1 */ 1050 .chn_num = 2, /* two channels for tsadc */ 1051 1052 .tshut_mode = TSHUT_MODE_GPIO, /* default TSHUT via GPIO give PMIC */ 1053 .tshut_polarity = TSHUT_LOW_ACTIVE, /* default TSHUT LOW ACTIVE */ 1054 .tshut_temp = 95000, 1055 1056 .initialize = rk_tsadcv3_initialize, 1057 .irq_ack = rk_tsadcv3_irq_ack, 1058 .control = rk_tsadcv3_control, 1059 .get_temp = rk_tsadcv2_get_temp, 1060 .set_alarm_temp = rk_tsadcv2_alarm_temp, 1061 .set_tshut_temp = rk_tsadcv2_tshut_temp, 1062 .set_tshut_mode = rk_tsadcv2_tshut_mode, 1063 1064 .table = { 1065 .id = rk3228_code_table, 1066 .length = ARRAY_SIZE(rk3228_code_table), 1067 .data_mask = TSADCV3_DATA_MASK, 1068 .mode = ADC_INCREMENT, 1069 }, 1070 }; 1071 1072 static const struct rockchip_tsadc_chip rk3368_tsadc_data = { 1073 .chn_id[SENSOR_CPU] = 0, /* cpu sensor is channel 0 */ 1074 .chn_id[SENSOR_GPU] = 1, /* gpu sensor is channel 1 */ 1075 .chn_num = 2, /* two channels for tsadc */ 1076 1077 .tshut_mode = TSHUT_MODE_GPIO, /* default TSHUT via GPIO give PMIC */ 1078 .tshut_polarity = TSHUT_LOW_ACTIVE, /* default TSHUT LOW ACTIVE */ 1079 .tshut_temp = 95000, 1080 1081 .initialize = rk_tsadcv2_initialize, 1082 .irq_ack = rk_tsadcv2_irq_ack, 1083 .control = rk_tsadcv2_control, 1084 .get_temp = rk_tsadcv2_get_temp, 1085 .set_alarm_temp = rk_tsadcv2_alarm_temp, 1086 .set_tshut_temp = rk_tsadcv2_tshut_temp, 1087 .set_tshut_mode = rk_tsadcv2_tshut_mode, 1088 1089 .table = { 1090 .id = rk3368_code_table, 1091 .length = ARRAY_SIZE(rk3368_code_table), 1092 .data_mask = TSADCV3_DATA_MASK, 1093 .mode = ADC_INCREMENT, 1094 }, 1095 }; 1096 1097 static const struct rockchip_tsadc_chip rk3399_tsadc_data = { 1098 .chn_id[SENSOR_CPU] = 0, /* cpu sensor is channel 0 */ 1099 .chn_id[SENSOR_GPU] = 1, /* gpu sensor is channel 1 */ 1100 .chn_num = 2, /* two channels for tsadc */ 1101 1102 .tshut_mode = TSHUT_MODE_GPIO, /* default TSHUT via GPIO give PMIC */ 1103 .tshut_polarity = TSHUT_LOW_ACTIVE, /* default TSHUT LOW ACTIVE */ 1104 .tshut_temp = 95000, 1105 1106 .initialize = rk_tsadcv3_initialize, 1107 .irq_ack = rk_tsadcv3_irq_ack, 1108 .control = rk_tsadcv3_control, 1109 .get_temp = rk_tsadcv2_get_temp, 1110 .set_alarm_temp = rk_tsadcv2_alarm_temp, 1111 .set_tshut_temp = rk_tsadcv2_tshut_temp, 1112 .set_tshut_mode = rk_tsadcv2_tshut_mode, 1113 1114 .table = { 1115 .id = rk3399_code_table, 1116 .length = ARRAY_SIZE(rk3399_code_table), 1117 .data_mask = TSADCV3_DATA_MASK, 1118 .mode = ADC_INCREMENT, 1119 }, 1120 }; 1121 1122 static const struct rockchip_tsadc_chip rk3568_tsadc_data = { 1123 .chn_id[SENSOR_CPU] = 0, /* cpu sensor is channel 0 */ 1124 .chn_id[SENSOR_GPU] = 1, /* gpu sensor is channel 1 */ 1125 .chn_num = 2, /* two channels for tsadc */ 1126 1127 .tshut_mode = TSHUT_MODE_GPIO, /* default TSHUT via GPIO give PMIC */ 1128 .tshut_polarity = TSHUT_LOW_ACTIVE, /* default TSHUT LOW ACTIVE */ 1129 .tshut_temp = 95000, 1130 1131 .initialize = rk_tsadcv7_initialize, 1132 .irq_ack = rk_tsadcv3_irq_ack, 1133 .control = rk_tsadcv3_control, 1134 .get_temp = rk_tsadcv2_get_temp, 1135 .set_alarm_temp = rk_tsadcv2_alarm_temp, 1136 .set_tshut_temp = rk_tsadcv2_tshut_temp, 1137 .set_tshut_mode = rk_tsadcv2_tshut_mode, 1138 1139 .table = { 1140 .id = rk3568_code_table, 1141 .length = ARRAY_SIZE(rk3568_code_table), 1142 .data_mask = TSADCV2_DATA_MASK, 1143 .mode = ADC_INCREMENT, 1144 }, 1145 }; 1146 1147 static const struct of_device_id of_rockchip_thermal_match[] = { 1148 { .compatible = "rockchip,px30-tsadc", 1149 .data = (void *)&px30_tsadc_data, 1150 }, 1151 { 1152 .compatible = "rockchip,rv1108-tsadc", 1153 .data = (void *)&rv1108_tsadc_data, 1154 }, 1155 { 1156 .compatible = "rockchip,rk3228-tsadc", 1157 .data = (void *)&rk3228_tsadc_data, 1158 }, 1159 { 1160 .compatible = "rockchip,rk3288-tsadc", 1161 .data = (void *)&rk3288_tsadc_data, 1162 }, 1163 { 1164 .compatible = "rockchip,rk3328-tsadc", 1165 .data = (void *)&rk3328_tsadc_data, 1166 }, 1167 { 1168 .compatible = "rockchip,rk3366-tsadc", 1169 .data = (void *)&rk3366_tsadc_data, 1170 }, 1171 { 1172 .compatible = "rockchip,rk3368-tsadc", 1173 .data = (void *)&rk3368_tsadc_data, 1174 }, 1175 { 1176 .compatible = "rockchip,rk3399-tsadc", 1177 .data = (void *)&rk3399_tsadc_data, 1178 }, 1179 { 1180 .compatible = "rockchip,rk3568-tsadc", 1181 .data = (void *)&rk3568_tsadc_data, 1182 }, 1183 { /* end */ }, 1184 }; 1185 MODULE_DEVICE_TABLE(of, of_rockchip_thermal_match); 1186 1187 static void 1188 rockchip_thermal_toggle_sensor(struct rockchip_thermal_sensor *sensor, bool on) 1189 { 1190 struct thermal_zone_device *tzd = sensor->tzd; 1191 1192 if (on) 1193 thermal_zone_device_enable(tzd); 1194 else 1195 thermal_zone_device_disable(tzd); 1196 } 1197 1198 static irqreturn_t rockchip_thermal_alarm_irq_thread(int irq, void *dev) 1199 { 1200 struct rockchip_thermal_data *thermal = dev; 1201 int i; 1202 1203 dev_dbg(&thermal->pdev->dev, "thermal alarm\n"); 1204 1205 thermal->chip->irq_ack(thermal->regs); 1206 1207 for (i = 0; i < thermal->chip->chn_num; i++) 1208 thermal_zone_device_update(thermal->sensors[i].tzd, 1209 THERMAL_EVENT_UNSPECIFIED); 1210 1211 return IRQ_HANDLED; 1212 } 1213 1214 static int rockchip_thermal_set_trips(struct thermal_zone_device *tz, int low, int high) 1215 { 1216 struct rockchip_thermal_sensor *sensor = tz->devdata; 1217 struct rockchip_thermal_data *thermal = sensor->thermal; 1218 const struct rockchip_tsadc_chip *tsadc = thermal->chip; 1219 1220 dev_dbg(&thermal->pdev->dev, "%s: sensor %d: low: %d, high %d\n", 1221 __func__, sensor->id, low, high); 1222 1223 return tsadc->set_alarm_temp(&tsadc->table, 1224 sensor->id, thermal->regs, high); 1225 } 1226 1227 static int rockchip_thermal_get_temp(struct thermal_zone_device *tz, int *out_temp) 1228 { 1229 struct rockchip_thermal_sensor *sensor = tz->devdata; 1230 struct rockchip_thermal_data *thermal = sensor->thermal; 1231 const struct rockchip_tsadc_chip *tsadc = sensor->thermal->chip; 1232 int retval; 1233 1234 retval = tsadc->get_temp(&tsadc->table, 1235 sensor->id, thermal->regs, out_temp); 1236 dev_dbg(&thermal->pdev->dev, "sensor %d - temp: %d, retval: %d\n", 1237 sensor->id, *out_temp, retval); 1238 1239 return retval; 1240 } 1241 1242 static const struct thermal_zone_device_ops rockchip_of_thermal_ops = { 1243 .get_temp = rockchip_thermal_get_temp, 1244 .set_trips = rockchip_thermal_set_trips, 1245 }; 1246 1247 static int rockchip_configure_from_dt(struct device *dev, 1248 struct device_node *np, 1249 struct rockchip_thermal_data *thermal) 1250 { 1251 u32 shut_temp, tshut_mode, tshut_polarity; 1252 1253 if (of_property_read_u32(np, "rockchip,hw-tshut-temp", &shut_temp)) { 1254 dev_warn(dev, 1255 "Missing tshut temp property, using default %d\n", 1256 thermal->chip->tshut_temp); 1257 thermal->tshut_temp = thermal->chip->tshut_temp; 1258 } else { 1259 if (shut_temp > INT_MAX) { 1260 dev_err(dev, "Invalid tshut temperature specified: %d\n", 1261 shut_temp); 1262 return -ERANGE; 1263 } 1264 thermal->tshut_temp = shut_temp; 1265 } 1266 1267 if (of_property_read_u32(np, "rockchip,hw-tshut-mode", &tshut_mode)) { 1268 dev_warn(dev, 1269 "Missing tshut mode property, using default (%s)\n", 1270 thermal->chip->tshut_mode == TSHUT_MODE_GPIO ? 1271 "gpio" : "cru"); 1272 thermal->tshut_mode = thermal->chip->tshut_mode; 1273 } else { 1274 thermal->tshut_mode = tshut_mode; 1275 } 1276 1277 if (thermal->tshut_mode > 1) { 1278 dev_err(dev, "Invalid tshut mode specified: %d\n", 1279 thermal->tshut_mode); 1280 return -EINVAL; 1281 } 1282 1283 if (of_property_read_u32(np, "rockchip,hw-tshut-polarity", 1284 &tshut_polarity)) { 1285 dev_warn(dev, 1286 "Missing tshut-polarity property, using default (%s)\n", 1287 thermal->chip->tshut_polarity == TSHUT_LOW_ACTIVE ? 1288 "low" : "high"); 1289 thermal->tshut_polarity = thermal->chip->tshut_polarity; 1290 } else { 1291 thermal->tshut_polarity = tshut_polarity; 1292 } 1293 1294 if (thermal->tshut_polarity > 1) { 1295 dev_err(dev, "Invalid tshut-polarity specified: %d\n", 1296 thermal->tshut_polarity); 1297 return -EINVAL; 1298 } 1299 1300 /* The tsadc wont to handle the error in here since some SoCs didn't 1301 * need this property. 1302 */ 1303 thermal->grf = syscon_regmap_lookup_by_phandle(np, "rockchip,grf"); 1304 if (IS_ERR(thermal->grf)) 1305 dev_warn(dev, "Missing rockchip,grf property\n"); 1306 1307 return 0; 1308 } 1309 1310 static int 1311 rockchip_thermal_register_sensor(struct platform_device *pdev, 1312 struct rockchip_thermal_data *thermal, 1313 struct rockchip_thermal_sensor *sensor, 1314 int id) 1315 { 1316 const struct rockchip_tsadc_chip *tsadc = thermal->chip; 1317 int error; 1318 1319 tsadc->set_tshut_mode(id, thermal->regs, thermal->tshut_mode); 1320 1321 error = tsadc->set_tshut_temp(&tsadc->table, id, thermal->regs, 1322 thermal->tshut_temp); 1323 if (error) 1324 dev_err(&pdev->dev, "%s: invalid tshut=%d, error=%d\n", 1325 __func__, thermal->tshut_temp, error); 1326 1327 sensor->thermal = thermal; 1328 sensor->id = id; 1329 sensor->tzd = devm_thermal_of_zone_register(&pdev->dev, id, sensor, 1330 &rockchip_of_thermal_ops); 1331 if (IS_ERR(sensor->tzd)) { 1332 error = PTR_ERR(sensor->tzd); 1333 dev_err(&pdev->dev, "failed to register sensor %d: %d\n", 1334 id, error); 1335 return error; 1336 } 1337 1338 return 0; 1339 } 1340 1341 /** 1342 * Reset TSADC Controller, reset all tsadc registers. 1343 * @reset: the reset controller of tsadc 1344 */ 1345 static void rockchip_thermal_reset_controller(struct reset_control *reset) 1346 { 1347 reset_control_assert(reset); 1348 usleep_range(10, 20); 1349 reset_control_deassert(reset); 1350 } 1351 1352 static int rockchip_thermal_probe(struct platform_device *pdev) 1353 { 1354 struct device_node *np = pdev->dev.of_node; 1355 struct rockchip_thermal_data *thermal; 1356 const struct of_device_id *match; 1357 struct resource *res; 1358 int irq; 1359 int i; 1360 int error; 1361 1362 match = of_match_node(of_rockchip_thermal_match, np); 1363 if (!match) 1364 return -ENXIO; 1365 1366 irq = platform_get_irq(pdev, 0); 1367 if (irq < 0) 1368 return -EINVAL; 1369 1370 thermal = devm_kzalloc(&pdev->dev, sizeof(struct rockchip_thermal_data), 1371 GFP_KERNEL); 1372 if (!thermal) 1373 return -ENOMEM; 1374 1375 thermal->pdev = pdev; 1376 1377 thermal->chip = (const struct rockchip_tsadc_chip *)match->data; 1378 if (!thermal->chip) 1379 return -EINVAL; 1380 1381 res = platform_get_resource(pdev, IORESOURCE_MEM, 0); 1382 thermal->regs = devm_ioremap_resource(&pdev->dev, res); 1383 if (IS_ERR(thermal->regs)) 1384 return PTR_ERR(thermal->regs); 1385 1386 thermal->reset = devm_reset_control_array_get(&pdev->dev, false, false); 1387 if (IS_ERR(thermal->reset)) { 1388 error = PTR_ERR(thermal->reset); 1389 dev_err(&pdev->dev, "failed to get tsadc reset: %d\n", error); 1390 return error; 1391 } 1392 1393 thermal->clk = devm_clk_get(&pdev->dev, "tsadc"); 1394 if (IS_ERR(thermal->clk)) { 1395 error = PTR_ERR(thermal->clk); 1396 dev_err(&pdev->dev, "failed to get tsadc clock: %d\n", error); 1397 return error; 1398 } 1399 1400 thermal->pclk = devm_clk_get(&pdev->dev, "apb_pclk"); 1401 if (IS_ERR(thermal->pclk)) { 1402 error = PTR_ERR(thermal->pclk); 1403 dev_err(&pdev->dev, "failed to get apb_pclk clock: %d\n", 1404 error); 1405 return error; 1406 } 1407 1408 error = clk_prepare_enable(thermal->clk); 1409 if (error) { 1410 dev_err(&pdev->dev, "failed to enable converter clock: %d\n", 1411 error); 1412 return error; 1413 } 1414 1415 error = clk_prepare_enable(thermal->pclk); 1416 if (error) { 1417 dev_err(&pdev->dev, "failed to enable pclk: %d\n", error); 1418 goto err_disable_clk; 1419 } 1420 1421 rockchip_thermal_reset_controller(thermal->reset); 1422 1423 error = rockchip_configure_from_dt(&pdev->dev, np, thermal); 1424 if (error) { 1425 dev_err(&pdev->dev, "failed to parse device tree data: %d\n", 1426 error); 1427 goto err_disable_pclk; 1428 } 1429 1430 thermal->chip->initialize(thermal->grf, thermal->regs, 1431 thermal->tshut_polarity); 1432 1433 for (i = 0; i < thermal->chip->chn_num; i++) { 1434 error = rockchip_thermal_register_sensor(pdev, thermal, 1435 &thermal->sensors[i], 1436 thermal->chip->chn_id[i]); 1437 if (error) { 1438 dev_err(&pdev->dev, 1439 "failed to register sensor[%d] : error = %d\n", 1440 i, error); 1441 goto err_disable_pclk; 1442 } 1443 } 1444 1445 error = devm_request_threaded_irq(&pdev->dev, irq, NULL, 1446 &rockchip_thermal_alarm_irq_thread, 1447 IRQF_ONESHOT, 1448 "rockchip_thermal", thermal); 1449 if (error) { 1450 dev_err(&pdev->dev, 1451 "failed to request tsadc irq: %d\n", error); 1452 goto err_disable_pclk; 1453 } 1454 1455 thermal->chip->control(thermal->regs, true); 1456 1457 for (i = 0; i < thermal->chip->chn_num; i++) { 1458 rockchip_thermal_toggle_sensor(&thermal->sensors[i], true); 1459 thermal->sensors[i].tzd->tzp->no_hwmon = false; 1460 error = thermal_add_hwmon_sysfs(thermal->sensors[i].tzd); 1461 if (error) 1462 dev_warn(&pdev->dev, 1463 "failed to register sensor %d with hwmon: %d\n", 1464 i, error); 1465 } 1466 1467 platform_set_drvdata(pdev, thermal); 1468 1469 return 0; 1470 1471 err_disable_pclk: 1472 clk_disable_unprepare(thermal->pclk); 1473 err_disable_clk: 1474 clk_disable_unprepare(thermal->clk); 1475 1476 return error; 1477 } 1478 1479 static int rockchip_thermal_remove(struct platform_device *pdev) 1480 { 1481 struct rockchip_thermal_data *thermal = platform_get_drvdata(pdev); 1482 int i; 1483 1484 for (i = 0; i < thermal->chip->chn_num; i++) { 1485 struct rockchip_thermal_sensor *sensor = &thermal->sensors[i]; 1486 1487 thermal_remove_hwmon_sysfs(sensor->tzd); 1488 rockchip_thermal_toggle_sensor(sensor, false); 1489 } 1490 1491 thermal->chip->control(thermal->regs, false); 1492 1493 clk_disable_unprepare(thermal->pclk); 1494 clk_disable_unprepare(thermal->clk); 1495 1496 return 0; 1497 } 1498 1499 static int __maybe_unused rockchip_thermal_suspend(struct device *dev) 1500 { 1501 struct rockchip_thermal_data *thermal = dev_get_drvdata(dev); 1502 int i; 1503 1504 for (i = 0; i < thermal->chip->chn_num; i++) 1505 rockchip_thermal_toggle_sensor(&thermal->sensors[i], false); 1506 1507 thermal->chip->control(thermal->regs, false); 1508 1509 clk_disable(thermal->pclk); 1510 clk_disable(thermal->clk); 1511 1512 pinctrl_pm_select_sleep_state(dev); 1513 1514 return 0; 1515 } 1516 1517 static int __maybe_unused rockchip_thermal_resume(struct device *dev) 1518 { 1519 struct rockchip_thermal_data *thermal = dev_get_drvdata(dev); 1520 int i; 1521 int error; 1522 1523 error = clk_enable(thermal->clk); 1524 if (error) 1525 return error; 1526 1527 error = clk_enable(thermal->pclk); 1528 if (error) { 1529 clk_disable(thermal->clk); 1530 return error; 1531 } 1532 1533 rockchip_thermal_reset_controller(thermal->reset); 1534 1535 thermal->chip->initialize(thermal->grf, thermal->regs, 1536 thermal->tshut_polarity); 1537 1538 for (i = 0; i < thermal->chip->chn_num; i++) { 1539 int id = thermal->sensors[i].id; 1540 1541 thermal->chip->set_tshut_mode(id, thermal->regs, 1542 thermal->tshut_mode); 1543 1544 error = thermal->chip->set_tshut_temp(&thermal->chip->table, 1545 id, thermal->regs, 1546 thermal->tshut_temp); 1547 if (error) 1548 dev_err(dev, "%s: invalid tshut=%d, error=%d\n", 1549 __func__, thermal->tshut_temp, error); 1550 } 1551 1552 thermal->chip->control(thermal->regs, true); 1553 1554 for (i = 0; i < thermal->chip->chn_num; i++) 1555 rockchip_thermal_toggle_sensor(&thermal->sensors[i], true); 1556 1557 pinctrl_pm_select_default_state(dev); 1558 1559 return 0; 1560 } 1561 1562 static SIMPLE_DEV_PM_OPS(rockchip_thermal_pm_ops, 1563 rockchip_thermal_suspend, rockchip_thermal_resume); 1564 1565 static struct platform_driver rockchip_thermal_driver = { 1566 .driver = { 1567 .name = "rockchip-thermal", 1568 .pm = &rockchip_thermal_pm_ops, 1569 .of_match_table = of_rockchip_thermal_match, 1570 }, 1571 .probe = rockchip_thermal_probe, 1572 .remove = rockchip_thermal_remove, 1573 }; 1574 1575 module_platform_driver(rockchip_thermal_driver); 1576 1577 MODULE_DESCRIPTION("ROCKCHIP THERMAL Driver"); 1578 MODULE_AUTHOR("Rockchip, Inc."); 1579 MODULE_LICENSE("GPL v2"); 1580 MODULE_ALIAS("platform:rockchip-thermal"); 1581