1 // SPDX-License-Identifier: GPL-2.0-only 2 /* intel_pch_thermal.c - Intel PCH Thermal driver 3 * 4 * Copyright (c) 2015, Intel Corporation. 5 * 6 * Authors: 7 * Tushar Dave <tushar.n.dave@intel.com> 8 */ 9 10 #include <linux/acpi.h> 11 #include <linux/delay.h> 12 #include <linux/module.h> 13 #include <linux/init.h> 14 #include <linux/pci.h> 15 #include <linux/pm.h> 16 #include <linux/suspend.h> 17 #include <linux/thermal.h> 18 #include <linux/types.h> 19 #include <linux/units.h> 20 21 /* Intel PCH thermal Device IDs */ 22 #define PCH_THERMAL_DID_HSW_1 0x9C24 /* Haswell PCH */ 23 #define PCH_THERMAL_DID_HSW_2 0x8C24 /* Haswell PCH */ 24 #define PCH_THERMAL_DID_WPT 0x9CA4 /* Wildcat Point */ 25 #define PCH_THERMAL_DID_SKL 0x9D31 /* Skylake PCH */ 26 #define PCH_THERMAL_DID_SKL_H 0xA131 /* Skylake PCH 100 series */ 27 #define PCH_THERMAL_DID_CNL 0x9Df9 /* CNL PCH */ 28 #define PCH_THERMAL_DID_CNL_H 0xA379 /* CNL-H PCH */ 29 #define PCH_THERMAL_DID_CNL_LP 0x02F9 /* CNL-LP PCH */ 30 #define PCH_THERMAL_DID_CML_H 0X06F9 /* CML-H PCH */ 31 #define PCH_THERMAL_DID_LWB 0xA1B1 /* Lewisburg PCH */ 32 33 /* Wildcat Point-LP PCH Thermal registers */ 34 #define WPT_TEMP 0x0000 /* Temperature */ 35 #define WPT_TSC 0x04 /* Thermal Sensor Control */ 36 #define WPT_TSS 0x06 /* Thermal Sensor Status */ 37 #define WPT_TSEL 0x08 /* Thermal Sensor Enable and Lock */ 38 #define WPT_TSREL 0x0A /* Thermal Sensor Report Enable and Lock */ 39 #define WPT_TSMIC 0x0C /* Thermal Sensor SMI Control */ 40 #define WPT_CTT 0x0010 /* Catastrophic Trip Point */ 41 #define WPT_TSPM 0x001C /* Thermal Sensor Power Management */ 42 #define WPT_TAHV 0x0014 /* Thermal Alert High Value */ 43 #define WPT_TALV 0x0018 /* Thermal Alert Low Value */ 44 #define WPT_TL 0x00000040 /* Throttle Value */ 45 #define WPT_PHL 0x0060 /* PCH Hot Level */ 46 #define WPT_PHLC 0x62 /* PHL Control */ 47 #define WPT_TAS 0x80 /* Thermal Alert Status */ 48 #define WPT_TSPIEN 0x82 /* PCI Interrupt Event Enables */ 49 #define WPT_TSGPEN 0x84 /* General Purpose Event Enables */ 50 51 /* Wildcat Point-LP PCH Thermal Register bit definitions */ 52 #define WPT_TEMP_TSR 0x01ff /* Temp TS Reading */ 53 #define WPT_TSC_CPDE 0x01 /* Catastrophic Power-Down Enable */ 54 #define WPT_TSS_TSDSS 0x10 /* Thermal Sensor Dynamic Shutdown Status */ 55 #define WPT_TSS_GPES 0x08 /* GPE status */ 56 #define WPT_TSEL_ETS 0x01 /* Enable TS */ 57 #define WPT_TSEL_PLDB 0x80 /* TSEL Policy Lock-Down Bit */ 58 #define WPT_TL_TOL 0x000001FF /* T0 Level */ 59 #define WPT_TL_T1L 0x1ff00000 /* T1 Level */ 60 #define WPT_TL_TTEN 0x20000000 /* TT Enable */ 61 62 /* Resolution of 1/2 degree C and an offset of -50C */ 63 #define PCH_TEMP_OFFSET (-50) 64 #define GET_WPT_TEMP(x) ((x) * MILLIDEGREE_PER_DEGREE / 2 + WPT_TEMP_OFFSET) 65 #define WPT_TEMP_OFFSET (PCH_TEMP_OFFSET * MILLIDEGREE_PER_DEGREE) 66 #define GET_PCH_TEMP(x) (((x) / 2) + PCH_TEMP_OFFSET) 67 68 /* Amount of time for each cooling delay, 100ms by default for now */ 69 static unsigned int delay_timeout = 100; 70 module_param(delay_timeout, int, 0644); 71 MODULE_PARM_DESC(delay_timeout, "amount of time delay for each iteration."); 72 73 /* Number of iterations for cooling delay, 600 counts by default for now */ 74 static unsigned int delay_cnt = 600; 75 module_param(delay_cnt, int, 0644); 76 MODULE_PARM_DESC(delay_cnt, "total number of iterations for time delay."); 77 78 static char driver_name[] = "Intel PCH thermal driver"; 79 80 struct pch_thermal_device { 81 void __iomem *hw_base; 82 const struct pch_dev_ops *ops; 83 struct pci_dev *pdev; 84 struct thermal_zone_device *tzd; 85 int crt_trip_id; 86 unsigned long crt_temp; 87 int hot_trip_id; 88 unsigned long hot_temp; 89 int psv_trip_id; 90 unsigned long psv_temp; 91 bool bios_enabled; 92 }; 93 94 #ifdef CONFIG_ACPI 95 96 /* 97 * On some platforms, there is a companion ACPI device, which adds 98 * passive trip temperature using _PSV method. There is no specific 99 * passive temperature setting in MMIO interface of this PCI device. 100 */ 101 static void pch_wpt_add_acpi_psv_trip(struct pch_thermal_device *ptd, 102 int *nr_trips) 103 { 104 struct acpi_device *adev; 105 106 ptd->psv_trip_id = -1; 107 108 adev = ACPI_COMPANION(&ptd->pdev->dev); 109 if (adev) { 110 unsigned long long r; 111 acpi_status status; 112 113 status = acpi_evaluate_integer(adev->handle, "_PSV", NULL, 114 &r); 115 if (ACPI_SUCCESS(status)) { 116 unsigned long trip_temp; 117 118 trip_temp = deci_kelvin_to_millicelsius(r); 119 if (trip_temp) { 120 ptd->psv_temp = trip_temp; 121 ptd->psv_trip_id = *nr_trips; 122 ++(*nr_trips); 123 } 124 } 125 } 126 } 127 #else 128 static void pch_wpt_add_acpi_psv_trip(struct pch_thermal_device *ptd, 129 int *nr_trips) 130 { 131 ptd->psv_trip_id = -1; 132 133 } 134 #endif 135 136 static int pch_wpt_init(struct pch_thermal_device *ptd, int *nr_trips) 137 { 138 u8 tsel; 139 u16 trip_temp; 140 141 *nr_trips = 0; 142 143 /* Check if BIOS has already enabled thermal sensor */ 144 if (WPT_TSEL_ETS & readb(ptd->hw_base + WPT_TSEL)) { 145 ptd->bios_enabled = true; 146 goto read_trips; 147 } 148 149 tsel = readb(ptd->hw_base + WPT_TSEL); 150 /* 151 * When TSEL's Policy Lock-Down bit is 1, TSEL become RO. 152 * If so, thermal sensor cannot enable. Bail out. 153 */ 154 if (tsel & WPT_TSEL_PLDB) { 155 dev_err(&ptd->pdev->dev, "Sensor can't be enabled\n"); 156 return -ENODEV; 157 } 158 159 writeb(tsel|WPT_TSEL_ETS, ptd->hw_base + WPT_TSEL); 160 if (!(WPT_TSEL_ETS & readb(ptd->hw_base + WPT_TSEL))) { 161 dev_err(&ptd->pdev->dev, "Sensor can't be enabled\n"); 162 return -ENODEV; 163 } 164 165 read_trips: 166 ptd->crt_trip_id = -1; 167 trip_temp = readw(ptd->hw_base + WPT_CTT); 168 trip_temp &= 0x1FF; 169 if (trip_temp) { 170 ptd->crt_temp = GET_WPT_TEMP(trip_temp); 171 ptd->crt_trip_id = 0; 172 ++(*nr_trips); 173 } 174 175 ptd->hot_trip_id = -1; 176 trip_temp = readw(ptd->hw_base + WPT_PHL); 177 trip_temp &= 0x1FF; 178 if (trip_temp) { 179 ptd->hot_temp = GET_WPT_TEMP(trip_temp); 180 ptd->hot_trip_id = *nr_trips; 181 ++(*nr_trips); 182 } 183 184 pch_wpt_add_acpi_psv_trip(ptd, nr_trips); 185 186 return 0; 187 } 188 189 static int pch_wpt_get_temp(struct pch_thermal_device *ptd, int *temp) 190 { 191 *temp = GET_WPT_TEMP(WPT_TEMP_TSR & readw(ptd->hw_base + WPT_TEMP)); 192 193 return 0; 194 } 195 196 /* Cool the PCH when it's overheat in .suspend_noirq phase */ 197 static int pch_wpt_suspend(struct pch_thermal_device *ptd) 198 { 199 u8 tsel; 200 int pch_delay_cnt = 0; 201 u16 pch_thr_temp, pch_cur_temp; 202 203 /* Shutdown the thermal sensor if it is not enabled by BIOS */ 204 if (!ptd->bios_enabled) { 205 tsel = readb(ptd->hw_base + WPT_TSEL); 206 writeb(tsel & 0xFE, ptd->hw_base + WPT_TSEL); 207 return 0; 208 } 209 210 /* Do not check temperature if it is not s2idle */ 211 if (pm_suspend_via_firmware()) 212 return 0; 213 214 /* Get the PCH temperature threshold value */ 215 pch_thr_temp = GET_PCH_TEMP(WPT_TEMP_TSR & readw(ptd->hw_base + WPT_TSPM)); 216 217 /* Get the PCH current temperature value */ 218 pch_cur_temp = GET_PCH_TEMP(WPT_TEMP_TSR & readw(ptd->hw_base + WPT_TEMP)); 219 220 /* 221 * If current PCH temperature is higher than configured PCH threshold 222 * value, run some delay loop with sleep to let the current temperature 223 * go down below the threshold value which helps to allow system enter 224 * lower power S0ix suspend state. Even after delay loop if PCH current 225 * temperature stays above threshold, notify the warning message 226 * which helps to indentify the reason why S0ix entry was rejected. 227 */ 228 while (pch_delay_cnt < delay_cnt) { 229 if (pch_cur_temp < pch_thr_temp) 230 break; 231 232 if (pm_wakeup_pending()) { 233 dev_warn(&ptd->pdev->dev, "Wakeup event detected, abort cooling\n"); 234 return 0; 235 } 236 237 pch_delay_cnt++; 238 dev_dbg(&ptd->pdev->dev, 239 "CPU-PCH current temp [%dC] higher than the threshold temp [%dC], sleep %d times for %d ms duration\n", 240 pch_cur_temp, pch_thr_temp, pch_delay_cnt, delay_timeout); 241 msleep(delay_timeout); 242 /* Read the PCH current temperature for next cycle. */ 243 pch_cur_temp = GET_PCH_TEMP(WPT_TEMP_TSR & readw(ptd->hw_base + WPT_TEMP)); 244 } 245 246 if (pch_cur_temp >= pch_thr_temp) 247 dev_warn(&ptd->pdev->dev, 248 "CPU-PCH is hot [%dC] after %d ms delay. S0ix might fail\n", 249 pch_cur_temp, pch_delay_cnt * delay_timeout); 250 else { 251 if (pch_delay_cnt) 252 dev_info(&ptd->pdev->dev, 253 "CPU-PCH is cool [%dC] after %d ms delay\n", 254 pch_cur_temp, pch_delay_cnt * delay_timeout); 255 else 256 dev_info(&ptd->pdev->dev, 257 "CPU-PCH is cool [%dC]\n", 258 pch_cur_temp); 259 } 260 261 return 0; 262 } 263 264 static int pch_wpt_resume(struct pch_thermal_device *ptd) 265 { 266 u8 tsel; 267 268 if (ptd->bios_enabled) 269 return 0; 270 271 tsel = readb(ptd->hw_base + WPT_TSEL); 272 273 writeb(tsel | WPT_TSEL_ETS, ptd->hw_base + WPT_TSEL); 274 275 return 0; 276 } 277 278 struct pch_dev_ops { 279 int (*hw_init)(struct pch_thermal_device *ptd, int *nr_trips); 280 int (*get_temp)(struct pch_thermal_device *ptd, int *temp); 281 int (*suspend)(struct pch_thermal_device *ptd); 282 int (*resume)(struct pch_thermal_device *ptd); 283 }; 284 285 286 /* dev ops for Wildcat Point */ 287 static const struct pch_dev_ops pch_dev_ops_wpt = { 288 .hw_init = pch_wpt_init, 289 .get_temp = pch_wpt_get_temp, 290 .suspend = pch_wpt_suspend, 291 .resume = pch_wpt_resume, 292 }; 293 294 static int pch_thermal_get_temp(struct thermal_zone_device *tzd, int *temp) 295 { 296 struct pch_thermal_device *ptd = tzd->devdata; 297 298 return ptd->ops->get_temp(ptd, temp); 299 } 300 301 static int pch_get_trip_type(struct thermal_zone_device *tzd, int trip, 302 enum thermal_trip_type *type) 303 { 304 struct pch_thermal_device *ptd = tzd->devdata; 305 306 if (ptd->crt_trip_id == trip) 307 *type = THERMAL_TRIP_CRITICAL; 308 else if (ptd->hot_trip_id == trip) 309 *type = THERMAL_TRIP_HOT; 310 else if (ptd->psv_trip_id == trip) 311 *type = THERMAL_TRIP_PASSIVE; 312 else 313 return -EINVAL; 314 315 return 0; 316 } 317 318 static int pch_get_trip_temp(struct thermal_zone_device *tzd, int trip, int *temp) 319 { 320 struct pch_thermal_device *ptd = tzd->devdata; 321 322 if (ptd->crt_trip_id == trip) 323 *temp = ptd->crt_temp; 324 else if (ptd->hot_trip_id == trip) 325 *temp = ptd->hot_temp; 326 else if (ptd->psv_trip_id == trip) 327 *temp = ptd->psv_temp; 328 else 329 return -EINVAL; 330 331 return 0; 332 } 333 334 static void pch_critical(struct thermal_zone_device *tzd) 335 { 336 dev_dbg(&tzd->device, "%s: critical temperature reached\n", tzd->type); 337 } 338 339 static struct thermal_zone_device_ops tzd_ops = { 340 .get_temp = pch_thermal_get_temp, 341 .get_trip_type = pch_get_trip_type, 342 .get_trip_temp = pch_get_trip_temp, 343 .critical = pch_critical, 344 }; 345 346 enum board_ids { 347 board_hsw, 348 board_wpt, 349 board_skl, 350 board_cnl, 351 board_cml, 352 board_lwb, 353 }; 354 355 static const struct board_info { 356 const char *name; 357 const struct pch_dev_ops *ops; 358 } board_info[] = { 359 [board_hsw] = { 360 .name = "pch_haswell", 361 .ops = &pch_dev_ops_wpt, 362 }, 363 [board_wpt] = { 364 .name = "pch_wildcat_point", 365 .ops = &pch_dev_ops_wpt, 366 }, 367 [board_skl] = { 368 .name = "pch_skylake", 369 .ops = &pch_dev_ops_wpt, 370 }, 371 [board_cnl] = { 372 .name = "pch_cannonlake", 373 .ops = &pch_dev_ops_wpt, 374 }, 375 [board_cml] = { 376 .name = "pch_cometlake", 377 .ops = &pch_dev_ops_wpt, 378 }, 379 [board_lwb] = { 380 .name = "pch_lewisburg", 381 .ops = &pch_dev_ops_wpt, 382 }, 383 }; 384 385 static int intel_pch_thermal_probe(struct pci_dev *pdev, 386 const struct pci_device_id *id) 387 { 388 enum board_ids board_id = id->driver_data; 389 const struct board_info *bi = &board_info[board_id]; 390 struct pch_thermal_device *ptd; 391 int err; 392 int nr_trips; 393 394 ptd = devm_kzalloc(&pdev->dev, sizeof(*ptd), GFP_KERNEL); 395 if (!ptd) 396 return -ENOMEM; 397 398 ptd->ops = bi->ops; 399 400 pci_set_drvdata(pdev, ptd); 401 ptd->pdev = pdev; 402 403 err = pci_enable_device(pdev); 404 if (err) { 405 dev_err(&pdev->dev, "failed to enable pci device\n"); 406 return err; 407 } 408 409 err = pci_request_regions(pdev, driver_name); 410 if (err) { 411 dev_err(&pdev->dev, "failed to request pci region\n"); 412 goto error_disable; 413 } 414 415 ptd->hw_base = pci_ioremap_bar(pdev, 0); 416 if (!ptd->hw_base) { 417 err = -ENOMEM; 418 dev_err(&pdev->dev, "failed to map mem base\n"); 419 goto error_release; 420 } 421 422 err = ptd->ops->hw_init(ptd, &nr_trips); 423 if (err) 424 goto error_cleanup; 425 426 ptd->tzd = thermal_zone_device_register(bi->name, nr_trips, 0, ptd, 427 &tzd_ops, NULL, 0, 0); 428 if (IS_ERR(ptd->tzd)) { 429 dev_err(&pdev->dev, "Failed to register thermal zone %s\n", 430 bi->name); 431 err = PTR_ERR(ptd->tzd); 432 goto error_cleanup; 433 } 434 err = thermal_zone_device_enable(ptd->tzd); 435 if (err) 436 goto err_unregister; 437 438 return 0; 439 440 err_unregister: 441 thermal_zone_device_unregister(ptd->tzd); 442 error_cleanup: 443 iounmap(ptd->hw_base); 444 error_release: 445 pci_release_regions(pdev); 446 error_disable: 447 pci_disable_device(pdev); 448 dev_err(&pdev->dev, "pci device failed to probe\n"); 449 return err; 450 } 451 452 static void intel_pch_thermal_remove(struct pci_dev *pdev) 453 { 454 struct pch_thermal_device *ptd = pci_get_drvdata(pdev); 455 456 thermal_zone_device_unregister(ptd->tzd); 457 iounmap(ptd->hw_base); 458 pci_set_drvdata(pdev, NULL); 459 pci_release_regions(pdev); 460 pci_disable_device(pdev); 461 } 462 463 static int intel_pch_thermal_suspend_noirq(struct device *device) 464 { 465 struct pch_thermal_device *ptd = dev_get_drvdata(device); 466 467 return ptd->ops->suspend(ptd); 468 } 469 470 static int intel_pch_thermal_resume(struct device *device) 471 { 472 struct pch_thermal_device *ptd = dev_get_drvdata(device); 473 474 return ptd->ops->resume(ptd); 475 } 476 477 static const struct pci_device_id intel_pch_thermal_id[] = { 478 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCH_THERMAL_DID_HSW_1), 479 .driver_data = board_hsw, }, 480 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCH_THERMAL_DID_HSW_2), 481 .driver_data = board_hsw, }, 482 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCH_THERMAL_DID_WPT), 483 .driver_data = board_wpt, }, 484 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCH_THERMAL_DID_SKL), 485 .driver_data = board_skl, }, 486 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCH_THERMAL_DID_SKL_H), 487 .driver_data = board_skl, }, 488 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCH_THERMAL_DID_CNL), 489 .driver_data = board_cnl, }, 490 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCH_THERMAL_DID_CNL_H), 491 .driver_data = board_cnl, }, 492 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCH_THERMAL_DID_CNL_LP), 493 .driver_data = board_cnl, }, 494 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCH_THERMAL_DID_CML_H), 495 .driver_data = board_cml, }, 496 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCH_THERMAL_DID_LWB), 497 .driver_data = board_lwb, }, 498 { 0, }, 499 }; 500 MODULE_DEVICE_TABLE(pci, intel_pch_thermal_id); 501 502 static const struct dev_pm_ops intel_pch_pm_ops = { 503 .suspend_noirq = intel_pch_thermal_suspend_noirq, 504 .resume = intel_pch_thermal_resume, 505 }; 506 507 static struct pci_driver intel_pch_thermal_driver = { 508 .name = "intel_pch_thermal", 509 .id_table = intel_pch_thermal_id, 510 .probe = intel_pch_thermal_probe, 511 .remove = intel_pch_thermal_remove, 512 .driver.pm = &intel_pch_pm_ops, 513 }; 514 515 module_pci_driver(intel_pch_thermal_driver); 516 517 MODULE_LICENSE("GPL v2"); 518 MODULE_DESCRIPTION("Intel PCH Thermal driver"); 519