1# SPDX-License-Identifier: GPL-2.0-only 2# 3# Generic thermal drivers configuration 4# 5 6menuconfig THERMAL 7 bool "Thermal drivers" 8 help 9 Thermal drivers offer a generic mechanism for 10 thermal management. Usually it's made up of one or more thermal 11 zones and cooling devices. 12 Each thermal zone contains its own temperature, trip points, 13 and cooling devices. 14 All platforms with ACPI or Open Firmware thermal support can use 15 this driver. 16 If you want this support, you should say Y here. 17 18if THERMAL 19 20config THERMAL_NETLINK 21 bool "Thermal netlink management" 22 depends on NET 23 help 24 The thermal framework has a netlink interface to do thermal 25 zones discovery, temperature readings and events such as 26 trip point crossed, cooling device update or governor 27 change. It is recommended to enable the feature. 28 29config THERMAL_STATISTICS 30 bool "Thermal state transition statistics" 31 help 32 Export thermal state transition statistics information through sysfs. 33 34 If in doubt, say N. 35 36config THERMAL_EMERGENCY_POWEROFF_DELAY_MS 37 int "Emergency poweroff delay in milli-seconds" 38 default 0 39 help 40 Thermal subsystem will issue a graceful shutdown when 41 critical temperatures are reached using orderly_poweroff(). In 42 case of failure of an orderly_poweroff(), the thermal emergency 43 poweroff kicks in after a delay has elapsed and shuts down the system. 44 This config is number of milliseconds to delay before emergency 45 poweroff kicks in. Similarly to the critical trip point, 46 the delay should be carefully profiled so as to give adequate 47 time for orderly_poweroff() to finish on regular execution. 48 If set to 0 emergency poweroff will not be supported. 49 50 In doubt, leave as 0. 51 52config THERMAL_HWMON 53 bool 54 prompt "Expose thermal sensors as hwmon device" 55 depends on HWMON=y || HWMON=THERMAL 56 default y 57 help 58 In case a sensor is registered with the thermal 59 framework, this option will also register it 60 as a hwmon. The sensor will then have the common 61 hwmon sysfs interface. 62 63 Say 'Y' here if you want all thermal sensors to 64 have hwmon sysfs interface too. 65 66config THERMAL_OF 67 bool 68 prompt "APIs to parse thermal data out of device tree" 69 depends on OF 70 default y 71 help 72 This options provides helpers to add the support to 73 read and parse thermal data definitions out of the 74 device tree blob. 75 76 Say 'Y' here if you need to build thermal infrastructure 77 based on device tree. 78 79config THERMAL_WRITABLE_TRIPS 80 bool "Enable writable trip points" 81 help 82 This option allows the system integrator to choose whether 83 trip temperatures can be changed from userspace. The 84 writable trips need to be specified when setting up the 85 thermal zone but the choice here takes precedence. 86 87 Say 'Y' here if you would like to allow userspace tools to 88 change trip temperatures. 89 90choice 91 prompt "Default Thermal governor" 92 default THERMAL_DEFAULT_GOV_STEP_WISE 93 help 94 This option sets which thermal governor shall be loaded at 95 startup. If in doubt, select 'step_wise'. 96 97config THERMAL_DEFAULT_GOV_STEP_WISE 98 bool "step_wise" 99 select THERMAL_GOV_STEP_WISE 100 help 101 Use the step_wise governor as default. This throttles the 102 devices one step at a time. 103 104config THERMAL_DEFAULT_GOV_FAIR_SHARE 105 bool "fair_share" 106 select THERMAL_GOV_FAIR_SHARE 107 help 108 Use the fair_share governor as default. This throttles the 109 devices based on their 'contribution' to a zone. The 110 contribution should be provided through platform data. 111 112config THERMAL_DEFAULT_GOV_USER_SPACE 113 bool "user_space" 114 select THERMAL_GOV_USER_SPACE 115 help 116 Select this if you want to let the user space manage the 117 platform thermals. 118 119config THERMAL_DEFAULT_GOV_POWER_ALLOCATOR 120 bool "power_allocator" 121 depends on THERMAL_GOV_POWER_ALLOCATOR 122 help 123 Select this if you want to control temperature based on 124 system and device power allocation. This governor can only 125 operate on cooling devices that implement the power API. 126 127endchoice 128 129config THERMAL_GOV_FAIR_SHARE 130 bool "Fair-share thermal governor" 131 help 132 Enable this to manage platform thermals using fair-share governor. 133 134config THERMAL_GOV_STEP_WISE 135 bool "Step_wise thermal governor" 136 help 137 Enable this to manage platform thermals using a simple linear 138 governor. 139 140config THERMAL_GOV_BANG_BANG 141 bool "Bang Bang thermal governor" 142 default n 143 help 144 Enable this to manage platform thermals using bang bang governor. 145 146 Say 'Y' here if you want to use two point temperature regulation 147 used for fans without throttling. Some fan drivers depend on this 148 governor to be enabled (e.g. acerhdf). 149 150config THERMAL_GOV_USER_SPACE 151 bool "User_space thermal governor" 152 help 153 Enable this to let the user space manage the platform thermals. 154 155config THERMAL_GOV_POWER_ALLOCATOR 156 bool "Power allocator thermal governor" 157 depends on ENERGY_MODEL 158 help 159 Enable this to manage platform thermals by dynamically 160 allocating and limiting power to devices. 161 162config CPU_THERMAL 163 bool "Generic cpu cooling support" 164 depends on THERMAL_OF 165 help 166 Enable the CPU cooling features. If the system has no active 167 cooling device available, this option allows to use the CPU 168 as a cooling device. 169 170if CPU_THERMAL 171 172config CPU_FREQ_THERMAL 173 bool "CPU frequency cooling device" 174 depends on CPU_FREQ 175 default y 176 help 177 This implements the generic cpu cooling mechanism through frequency 178 reduction. An ACPI version of this already exists 179 (drivers/acpi/processor_thermal.c). 180 This will be useful for platforms using the generic thermal interface 181 and not the ACPI interface. 182 183config CPU_IDLE_THERMAL 184 bool "CPU idle cooling device" 185 depends on IDLE_INJECT 186 help 187 This implements the CPU cooling mechanism through 188 idle injection. This will throttle the CPU by injecting 189 idle cycle. 190endif 191 192config DEVFREQ_THERMAL 193 bool "Generic device cooling support" 194 depends on PM_DEVFREQ 195 depends on PM_OPP 196 help 197 This implements the generic devfreq cooling mechanism through 198 frequency reduction for devices using devfreq. 199 200 This will throttle the device by limiting the maximum allowed DVFS 201 frequency corresponding to the cooling level. 202 203 In order to use the power extensions of the cooling device, 204 devfreq should use the simple_ondemand governor. 205 206 If you want this support, you should say Y here. 207 208config THERMAL_EMULATION 209 bool "Thermal emulation mode support" 210 help 211 Enable this option to make a emul_temp sysfs node in thermal zone 212 directory to support temperature emulation. With emulation sysfs node, 213 user can manually input temperature and test the different trip 214 threshold behaviour for simulation purpose. 215 216 WARNING: Be careful while enabling this option on production systems, 217 because userland can easily disable the thermal policy by simply 218 flooding this sysfs node with low temperature values. 219 220config THERMAL_MMIO 221 tristate "Generic Thermal MMIO driver" 222 depends on OF || COMPILE_TEST 223 depends on HAS_IOMEM 224 help 225 This option enables the generic thermal MMIO driver that will use 226 memory-mapped reads to get the temperature. Any HW/System that 227 allows temperature reading by a single memory-mapped reading, be it 228 register or shared memory, is a potential candidate to work with this 229 driver. 230 231config HISI_THERMAL 232 tristate "Hisilicon thermal driver" 233 depends on ARCH_HISI || COMPILE_TEST 234 depends on HAS_IOMEM 235 depends on OF 236 default y 237 help 238 Enable this to plug hisilicon's thermal sensor driver into the Linux 239 thermal framework. cpufreq is used as the cooling device to throttle 240 CPUs when the passive trip is crossed. 241 242config IMX_THERMAL 243 tristate "Temperature sensor driver for Freescale i.MX SoCs" 244 depends on ARCH_MXC || COMPILE_TEST 245 depends on NVMEM || !NVMEM 246 depends on MFD_SYSCON 247 depends on OF 248 help 249 Support for Temperature Monitor (TEMPMON) found on Freescale i.MX SoCs. 250 It supports one critical trip point and one passive trip point. The 251 cpufreq is used as the cooling device to throttle CPUs when the 252 passive trip is crossed. 253 254config IMX_SC_THERMAL 255 tristate "Temperature sensor driver for NXP i.MX SoCs with System Controller" 256 depends on IMX_SCU 257 depends on OF 258 help 259 Support for Temperature Monitor (TEMPMON) found on NXP i.MX SoCs with 260 system controller inside, Linux kernel has to communicate with system 261 controller via MU (message unit) IPC to get temperature from thermal 262 sensor. It supports one critical trip point and one 263 passive trip point for each thermal sensor. 264 265config IMX8MM_THERMAL 266 tristate "Temperature sensor driver for Freescale i.MX8MM SoC" 267 depends on ARCH_MXC || COMPILE_TEST 268 depends on OF 269 help 270 Support for Thermal Monitoring Unit (TMU) found on Freescale i.MX8MM SoC. 271 It supports one critical trip point and one passive trip point. The 272 cpufreq is used as the cooling device to throttle CPUs when the passive 273 trip is crossed. 274 275config K3_THERMAL 276 tristate "Texas Instruments K3 thermal support" 277 depends on ARCH_K3 || COMPILE_TEST 278 help 279 If you say yes here you get thermal support for the Texas Instruments 280 K3 SoC family. The current chip supported is: 281 - AM654 282 283 This includes temperature reading functionality. 284 285config MAX77620_THERMAL 286 tristate "Temperature sensor driver for Maxim MAX77620 PMIC" 287 depends on MFD_MAX77620 288 depends on OF 289 help 290 Support for die junction temperature warning alarm for Maxim 291 Semiconductor PMIC MAX77620 device. Device generates two alarm 292 interrupts when PMIC die temperature cross the threshold of 293 120 degC and 140 degC. 294 295config QORIQ_THERMAL 296 tristate "QorIQ Thermal Monitoring Unit" 297 depends on THERMAL_OF && HAS_IOMEM 298 depends on PPC_E500MC || SOC_LS1021A || ARCH_LAYERSCAPE || (ARCH_MXC && ARM64) || COMPILE_TEST 299 select REGMAP_MMIO 300 help 301 Support for Thermal Monitoring Unit (TMU) found on QorIQ platforms. 302 It supports one critical trip point and one passive trip point. The 303 cpufreq is used as the cooling device to throttle CPUs when the 304 passive trip is crossed. 305 306config SPEAR_THERMAL 307 tristate "SPEAr thermal sensor driver" 308 depends on PLAT_SPEAR || COMPILE_TEST 309 depends on HAS_IOMEM 310 depends on OF 311 help 312 Enable this to plug the SPEAr thermal sensor driver into the Linux 313 thermal framework. 314 315config SUN8I_THERMAL 316 tristate "Allwinner sun8i thermal driver" 317 depends on ARCH_SUNXI || COMPILE_TEST 318 depends on HAS_IOMEM 319 depends on NVMEM 320 depends on OF 321 depends on RESET_CONTROLLER 322 help 323 Support for the sun8i thermal sensor driver into the Linux thermal 324 framework. 325 326 To compile this driver as a module, choose M here: the 327 module will be called sun8i-thermal. 328 329config ROCKCHIP_THERMAL 330 tristate "Rockchip thermal driver" 331 depends on ARCH_ROCKCHIP || COMPILE_TEST 332 depends on RESET_CONTROLLER 333 depends on HAS_IOMEM 334 help 335 Rockchip thermal driver provides support for Temperature sensor 336 ADC (TS-ADC) found on Rockchip SoCs. It supports one critical 337 trip point. Cpufreq is used as the cooling device and will throttle 338 CPUs when the Temperature crosses the passive trip point. 339 340config RCAR_THERMAL 341 tristate "Renesas R-Car thermal driver" 342 depends on ARCH_RENESAS || COMPILE_TEST 343 depends on HAS_IOMEM 344 help 345 Enable this to plug the R-Car thermal sensor driver into the Linux 346 thermal framework. 347 348config RCAR_GEN3_THERMAL 349 tristate "Renesas R-Car Gen3 thermal driver" 350 depends on ARCH_RENESAS || COMPILE_TEST 351 depends on HAS_IOMEM 352 depends on OF 353 help 354 Enable this to plug the R-Car Gen3 thermal sensor driver into the Linux 355 thermal framework. 356 357config KIRKWOOD_THERMAL 358 tristate "Temperature sensor on Marvell Kirkwood SoCs" 359 depends on MACH_KIRKWOOD || COMPILE_TEST 360 depends on HAS_IOMEM 361 depends on OF 362 help 363 Support for the Kirkwood thermal sensor driver into the Linux thermal 364 framework. Only kirkwood 88F6282 and 88F6283 have this sensor. 365 366config DOVE_THERMAL 367 tristate "Temperature sensor on Marvell Dove SoCs" 368 depends on ARCH_DOVE || MACH_DOVE || COMPILE_TEST 369 depends on HAS_IOMEM 370 depends on OF 371 help 372 Support for the Dove thermal sensor driver in the Linux thermal 373 framework. 374 375config DB8500_THERMAL 376 tristate "DB8500 thermal management" 377 depends on MFD_DB8500_PRCMU && OF 378 default y 379 help 380 Adds DB8500 thermal management implementation according to the thermal 381 management framework. A thermal zone with several trip points will be 382 created. Cooling devices can be bound to the trip points to cool this 383 thermal zone if trip points reached. 384 385config ARMADA_THERMAL 386 tristate "Marvell EBU Armada SoCs thermal management" 387 depends on ARCH_MVEBU || COMPILE_TEST 388 depends on HAS_IOMEM 389 depends on OF 390 help 391 Enable this option if you want to have support for thermal management 392 controller present in Marvell EBU Armada SoCs (370,375,XP,38x,7K,8K). 393 394config DA9062_THERMAL 395 tristate "DA9062/DA9061 Dialog Semiconductor thermal driver" 396 depends on MFD_DA9062 || COMPILE_TEST 397 depends on OF 398 help 399 Enable this for the Dialog Semiconductor thermal sensor driver. 400 This will report PMIC junction over-temperature for one thermal trip 401 zone. 402 Compatible with the DA9062 and DA9061 PMICs. 403 404config MTK_THERMAL 405 tristate "Temperature sensor driver for mediatek SoCs" 406 depends on ARCH_MEDIATEK || COMPILE_TEST 407 depends on HAS_IOMEM 408 depends on NVMEM || NVMEM=n 409 depends on RESET_CONTROLLER 410 default y 411 help 412 Enable this option if you want to have support for thermal management 413 controller present in Mediatek SoCs 414 415config AMLOGIC_THERMAL 416 tristate "Amlogic Thermal Support" 417 default ARCH_MESON 418 depends on OF && ARCH_MESON 419 help 420 If you say yes here you get support for Amlogic Thermal 421 for G12 SoC Family. 422 423 This driver can also be built as a module. If so, the module will 424 be called amlogic_thermal. 425 426menu "Intel thermal drivers" 427depends on X86 || X86_INTEL_QUARK || COMPILE_TEST 428source "drivers/thermal/intel/Kconfig" 429endmenu 430 431menu "Broadcom thermal drivers" 432depends on ARCH_BCM || ARCH_BRCMSTB || ARCH_BCM2835 || ARCH_BCM_IPROC || \ 433 COMPILE_TEST 434source "drivers/thermal/broadcom/Kconfig" 435endmenu 436 437menu "Texas Instruments thermal drivers" 438depends on ARCH_HAS_BANDGAP || COMPILE_TEST 439depends on HAS_IOMEM 440source "drivers/thermal/ti-soc-thermal/Kconfig" 441endmenu 442 443menu "Samsung thermal drivers" 444depends on ARCH_EXYNOS || COMPILE_TEST 445source "drivers/thermal/samsung/Kconfig" 446endmenu 447 448menu "STMicroelectronics thermal drivers" 449depends on (ARCH_STI || ARCH_STM32) && OF 450source "drivers/thermal/st/Kconfig" 451endmenu 452 453config TANGO_THERMAL 454 tristate "Tango thermal management" 455 depends on ARCH_TANGO || COMPILE_TEST 456 help 457 Enable the Tango thermal driver, which supports the primitive 458 temperature sensor embedded in Tango chips since the SMP8758. 459 This sensor only generates a 1-bit signal to indicate whether 460 the die temperature exceeds a programmable threshold. 461 462source "drivers/thermal/tegra/Kconfig" 463 464config GENERIC_ADC_THERMAL 465 tristate "Generic ADC based thermal sensor" 466 depends on IIO 467 help 468 This enabled a thermal sysfs driver for the temperature sensor 469 which is connected to the General Purpose ADC. The ADC channel 470 is read via IIO framework and the channel information is provided 471 to this driver. This driver reports the temperature by reading ADC 472 channel and converts it to temperature based on lookup table. 473 474menu "Qualcomm thermal drivers" 475depends on (ARCH_QCOM && OF) || COMPILE_TEST 476source "drivers/thermal/qcom/Kconfig" 477endmenu 478 479config ZX2967_THERMAL 480 tristate "Thermal sensors on zx2967 SoC" 481 depends on ARCH_ZX || COMPILE_TEST 482 help 483 Enable the zx2967 thermal sensors driver, which supports 484 the primitive temperature sensor embedded in zx2967 SoCs. 485 This sensor generates the real time die temperature. 486 487config UNIPHIER_THERMAL 488 tristate "Socionext UniPhier thermal driver" 489 depends on ARCH_UNIPHIER || COMPILE_TEST 490 depends on THERMAL_OF && MFD_SYSCON 491 help 492 Enable this to plug in UniPhier on-chip PVT thermal driver into the 493 thermal framework. The driver supports CPU thermal zone temperature 494 reporting and a couple of trip points. 495 496config SPRD_THERMAL 497 tristate "Temperature sensor on Spreadtrum SoCs" 498 depends on ARCH_SPRD || COMPILE_TEST 499 help 500 Support for the Spreadtrum thermal sensor driver in the Linux thermal 501 framework. 502 503config KHADAS_MCU_FAN_THERMAL 504 tristate "Khadas MCU controller FAN cooling support" 505 depends on OF || COMPILE_TEST 506 depends on MFD_KHADAS_MCU 507 select MFD_CORE 508 select REGMAP 509 help 510 If you say yes here you get support for the FAN controlled 511 by the Microcontroller found on the Khadas VIM boards. 512 513endif 514