1# 2# Generic thermal sysfs drivers configuration 3# 4 5menuconfig THERMAL 6 tristate "Generic Thermal sysfs driver" 7 help 8 Generic Thermal Sysfs driver offers a generic mechanism for 9 thermal management. Usually it's made up of one or more thermal 10 zone and cooling device. 11 Each thermal zone contains its own temperature, trip points, 12 cooling devices. 13 All platforms with ACPI thermal support can use this driver. 14 If you want this support, you should say Y or M here. 15 16if THERMAL 17 18config THERMAL_EMERGENCY_POWEROFF_DELAY_MS 19 int "Emergency poweroff delay in milli-seconds" 20 depends on THERMAL 21 default 0 22 help 23 Thermal subsystem will issue a graceful shutdown when 24 critical temperatures are reached using orderly_poweroff(). In 25 case of failure of an orderly_poweroff(), the thermal emergency 26 poweroff kicks in after a delay has elapsed and shuts down the system. 27 This config is number of milliseconds to delay before emergency 28 poweroff kicks in. Similarly to the critical trip point, 29 the delay should be carefully profiled so as to give adequate 30 time for orderly_poweroff() to finish on regular execution. 31 If set to 0 emergency poweroff will not be supported. 32 33 In doubt, leave as 0. 34 35config THERMAL_HWMON 36 bool 37 prompt "Expose thermal sensors as hwmon device" 38 depends on HWMON=y || HWMON=THERMAL 39 default y 40 help 41 In case a sensor is registered with the thermal 42 framework, this option will also register it 43 as a hwmon. The sensor will then have the common 44 hwmon sysfs interface. 45 46 Say 'Y' here if you want all thermal sensors to 47 have hwmon sysfs interface too. 48 49config THERMAL_OF 50 bool 51 prompt "APIs to parse thermal data out of device tree" 52 depends on OF 53 default y 54 help 55 This options provides helpers to add the support to 56 read and parse thermal data definitions out of the 57 device tree blob. 58 59 Say 'Y' here if you need to build thermal infrastructure 60 based on device tree. 61 62config THERMAL_WRITABLE_TRIPS 63 bool "Enable writable trip points" 64 help 65 This option allows the system integrator to choose whether 66 trip temperatures can be changed from userspace. The 67 writable trips need to be specified when setting up the 68 thermal zone but the choice here takes precedence. 69 70 Say 'Y' here if you would like to allow userspace tools to 71 change trip temperatures. 72 73choice 74 prompt "Default Thermal governor" 75 default THERMAL_DEFAULT_GOV_STEP_WISE 76 help 77 This option sets which thermal governor shall be loaded at 78 startup. If in doubt, select 'step_wise'. 79 80config THERMAL_DEFAULT_GOV_STEP_WISE 81 bool "step_wise" 82 select THERMAL_GOV_STEP_WISE 83 help 84 Use the step_wise governor as default. This throttles the 85 devices one step at a time. 86 87config THERMAL_DEFAULT_GOV_FAIR_SHARE 88 bool "fair_share" 89 select THERMAL_GOV_FAIR_SHARE 90 help 91 Use the fair_share governor as default. This throttles the 92 devices based on their 'contribution' to a zone. The 93 contribution should be provided through platform data. 94 95config THERMAL_DEFAULT_GOV_USER_SPACE 96 bool "user_space" 97 select THERMAL_GOV_USER_SPACE 98 help 99 Select this if you want to let the user space manage the 100 platform thermals. 101 102config THERMAL_DEFAULT_GOV_POWER_ALLOCATOR 103 bool "power_allocator" 104 select THERMAL_GOV_POWER_ALLOCATOR 105 help 106 Select this if you want to control temperature based on 107 system and device power allocation. This governor can only 108 operate on cooling devices that implement the power API. 109 110endchoice 111 112config THERMAL_GOV_FAIR_SHARE 113 bool "Fair-share thermal governor" 114 help 115 Enable this to manage platform thermals using fair-share governor. 116 117config THERMAL_GOV_STEP_WISE 118 bool "Step_wise thermal governor" 119 help 120 Enable this to manage platform thermals using a simple linear 121 governor. 122 123config THERMAL_GOV_BANG_BANG 124 bool "Bang Bang thermal governor" 125 default n 126 help 127 Enable this to manage platform thermals using bang bang governor. 128 129 Say 'Y' here if you want to use two point temperature regulation 130 used for fans without throttling. Some fan drivers depend on this 131 governor to be enabled (e.g. acerhdf). 132 133config THERMAL_GOV_USER_SPACE 134 bool "User_space thermal governor" 135 help 136 Enable this to let the user space manage the platform thermals. 137 138config THERMAL_GOV_POWER_ALLOCATOR 139 bool "Power allocator thermal governor" 140 help 141 Enable this to manage platform thermals by dynamically 142 allocating and limiting power to devices. 143 144config CPU_THERMAL 145 bool "generic cpu cooling support" 146 depends on CPU_FREQ 147 depends on THERMAL_OF 148 help 149 This implements the generic cpu cooling mechanism through frequency 150 reduction. An ACPI version of this already exists 151 (drivers/acpi/processor_thermal.c). 152 This will be useful for platforms using the generic thermal interface 153 and not the ACPI interface. 154 155 If you want this support, you should say Y here. 156 157config CLOCK_THERMAL 158 bool "Generic clock cooling support" 159 depends on COMMON_CLK 160 depends on PM_OPP 161 help 162 This entry implements the generic clock cooling mechanism through 163 frequency clipping. Typically used to cool off co-processors. The 164 device that is configured to use this cooling mechanism will be 165 controlled to reduce clock frequency whenever temperature is high. 166 167config DEVFREQ_THERMAL 168 bool "Generic device cooling support" 169 depends on PM_DEVFREQ 170 depends on PM_OPP 171 help 172 This implements the generic devfreq cooling mechanism through 173 frequency reduction for devices using devfreq. 174 175 This will throttle the device by limiting the maximum allowed DVFS 176 frequency corresponding to the cooling level. 177 178 In order to use the power extensions of the cooling device, 179 devfreq should use the simple_ondemand governor. 180 181 If you want this support, you should say Y here. 182 183config THERMAL_EMULATION 184 bool "Thermal emulation mode support" 185 help 186 Enable this option to make a emul_temp sysfs node in thermal zone 187 directory to support temperature emulation. With emulation sysfs node, 188 user can manually input temperature and test the different trip 189 threshold behaviour for simulation purpose. 190 191 WARNING: Be careful while enabling this option on production systems, 192 because userland can easily disable the thermal policy by simply 193 flooding this sysfs node with low temperature values. 194 195config HISI_THERMAL 196 tristate "Hisilicon thermal driver" 197 depends on ARCH_HISI || COMPILE_TEST 198 depends on HAS_IOMEM 199 depends on OF 200 default y 201 help 202 Enable this to plug hisilicon's thermal sensor driver into the Linux 203 thermal framework. cpufreq is used as the cooling device to throttle 204 CPUs when the passive trip is crossed. 205 206config IMX_THERMAL 207 tristate "Temperature sensor driver for Freescale i.MX SoCs" 208 depends on (ARCH_MXC && CPU_THERMAL) || COMPILE_TEST 209 depends on NVMEM || !NVMEM 210 depends on MFD_SYSCON 211 depends on OF 212 help 213 Support for Temperature Monitor (TEMPMON) found on Freescale i.MX SoCs. 214 It supports one critical trip point and one passive trip point. The 215 cpufreq is used as the cooling device to throttle CPUs when the 216 passive trip is crossed. 217 218config MAX77620_THERMAL 219 tristate "Temperature sensor driver for Maxim MAX77620 PMIC" 220 depends on MFD_MAX77620 221 depends on OF 222 help 223 Support for die junction temperature warning alarm for Maxim 224 Semiconductor PMIC MAX77620 device. Device generates two alarm 225 interrupts when PMIC die temperature cross the threshold of 226 120 degC and 140 degC. 227 228config QORIQ_THERMAL 229 tristate "QorIQ Thermal Monitoring Unit" 230 depends on THERMAL_OF 231 depends on HAS_IOMEM 232 help 233 Support for Thermal Monitoring Unit (TMU) found on QorIQ platforms. 234 It supports one critical trip point and one passive trip point. The 235 cpufreq is used as the cooling device to throttle CPUs when the 236 passive trip is crossed. 237 238config SPEAR_THERMAL 239 tristate "SPEAr thermal sensor driver" 240 depends on PLAT_SPEAR || COMPILE_TEST 241 depends on HAS_IOMEM 242 depends on OF 243 help 244 Enable this to plug the SPEAr thermal sensor driver into the Linux 245 thermal framework. 246 247config ROCKCHIP_THERMAL 248 tristate "Rockchip thermal driver" 249 depends on ARCH_ROCKCHIP || COMPILE_TEST 250 depends on RESET_CONTROLLER 251 depends on HAS_IOMEM 252 help 253 Rockchip thermal driver provides support for Temperature sensor 254 ADC (TS-ADC) found on Rockchip SoCs. It supports one critical 255 trip point. Cpufreq is used as the cooling device and will throttle 256 CPUs when the Temperature crosses the passive trip point. 257 258config RCAR_THERMAL 259 tristate "Renesas R-Car thermal driver" 260 depends on ARCH_RENESAS || COMPILE_TEST 261 depends on HAS_IOMEM 262 help 263 Enable this to plug the R-Car thermal sensor driver into the Linux 264 thermal framework. 265 266config RCAR_GEN3_THERMAL 267 tristate "Renesas R-Car Gen3 thermal driver" 268 depends on ARCH_RENESAS || COMPILE_TEST 269 depends on HAS_IOMEM 270 depends on OF 271 help 272 Enable this to plug the R-Car Gen3 thermal sensor driver into the Linux 273 thermal framework. 274 275config KIRKWOOD_THERMAL 276 tristate "Temperature sensor on Marvell Kirkwood SoCs" 277 depends on MACH_KIRKWOOD || COMPILE_TEST 278 depends on HAS_IOMEM 279 depends on OF 280 help 281 Support for the Kirkwood thermal sensor driver into the Linux thermal 282 framework. Only kirkwood 88F6282 and 88F6283 have this sensor. 283 284config DOVE_THERMAL 285 tristate "Temperature sensor on Marvell Dove SoCs" 286 depends on ARCH_DOVE || MACH_DOVE || COMPILE_TEST 287 depends on HAS_IOMEM 288 depends on OF 289 help 290 Support for the Dove thermal sensor driver in the Linux thermal 291 framework. 292 293config DB8500_THERMAL 294 tristate "DB8500 thermal management" 295 depends on MFD_DB8500_PRCMU 296 default y 297 help 298 Adds DB8500 thermal management implementation according to the thermal 299 management framework. A thermal zone with several trip points will be 300 created. Cooling devices can be bound to the trip points to cool this 301 thermal zone if trip points reached. 302 303config ARMADA_THERMAL 304 tristate "Marvell EBU Armada SoCs thermal management" 305 depends on ARCH_MVEBU || COMPILE_TEST 306 depends on HAS_IOMEM 307 depends on OF 308 help 309 Enable this option if you want to have support for thermal management 310 controller present in Marvell EBU Armada SoCs (370,375,XP,38x,7K,8K). 311 312config DA9062_THERMAL 313 tristate "DA9062/DA9061 Dialog Semiconductor thermal driver" 314 depends on MFD_DA9062 || COMPILE_TEST 315 depends on OF 316 help 317 Enable this for the Dialog Semiconductor thermal sensor driver. 318 This will report PMIC junction over-temperature for one thermal trip 319 zone. 320 Compatible with the DA9062 and DA9061 PMICs. 321 322config INTEL_POWERCLAMP 323 tristate "Intel PowerClamp idle injection driver" 324 depends on THERMAL 325 depends on X86 326 depends on CPU_SUP_INTEL 327 help 328 Enable this to enable Intel PowerClamp idle injection driver. This 329 enforce idle time which results in more package C-state residency. The 330 user interface is exposed via generic thermal framework. 331 332config X86_PKG_TEMP_THERMAL 333 tristate "X86 package temperature thermal driver" 334 depends on X86_THERMAL_VECTOR 335 select THERMAL_GOV_USER_SPACE 336 select THERMAL_WRITABLE_TRIPS 337 default m 338 help 339 Enable this to register CPU digital sensor for package temperature as 340 thermal zone. Each package will have its own thermal zone. There are 341 two trip points which can be set by user to get notifications via thermal 342 notification methods. 343 344config INTEL_SOC_DTS_IOSF_CORE 345 tristate 346 depends on X86 && PCI 347 select IOSF_MBI 348 help 349 This is becoming a common feature for Intel SoCs to expose the additional 350 digital temperature sensors (DTSs) using side band interface (IOSF). This 351 implements the common set of helper functions to register, get temperature 352 and get/set thresholds on DTSs. 353 354config INTEL_SOC_DTS_THERMAL 355 tristate "Intel SoCs DTS thermal driver" 356 depends on X86 && PCI 357 select INTEL_SOC_DTS_IOSF_CORE 358 select THERMAL_WRITABLE_TRIPS 359 help 360 Enable this to register Intel SoCs (e.g. Bay Trail) platform digital 361 temperature sensor (DTS). These SoCs have two additional DTSs in 362 addition to DTSs on CPU cores. Each DTS will be registered as a 363 thermal zone. There are two trip points. One of the trip point can 364 be set by user mode programs to get notifications via Linux thermal 365 notification methods.The other trip is a critical trip point, which 366 was set by the driver based on the TJ MAX temperature. 367 368config INTEL_QUARK_DTS_THERMAL 369 tristate "Intel Quark DTS thermal driver" 370 depends on X86_INTEL_QUARK 371 help 372 Enable this to register Intel Quark SoC (e.g. X1000) platform digital 373 temperature sensor (DTS). For X1000 SoC, it has one on-die DTS. 374 The DTS will be registered as a thermal zone. There are two trip points: 375 hot & critical. The critical trip point default value is set by 376 underlying BIOS/Firmware. 377 378menu "ACPI INT340X thermal drivers" 379source drivers/thermal/int340x_thermal/Kconfig 380endmenu 381 382config INTEL_BXT_PMIC_THERMAL 383 tristate "Intel Broxton PMIC thermal driver" 384 depends on X86 && INTEL_SOC_PMIC_BXTWC && REGMAP 385 help 386 Select this driver for Intel Broxton PMIC with ADC channels monitoring 387 system temperature measurements and alerts. 388 This driver is used for monitoring the ADC channels of PMIC and handles 389 the alert trip point interrupts and notifies the thermal framework with 390 the trip point and temperature details of the zone. 391 392config INTEL_PCH_THERMAL 393 tristate "Intel PCH Thermal Reporting Driver" 394 depends on X86 && PCI 395 help 396 Enable this to support thermal reporting on certain intel PCHs. 397 Thermal reporting device will provide temperature reading, 398 programmable trip points and other information. 399 400config MTK_THERMAL 401 tristate "Temperature sensor driver for mediatek SoCs" 402 depends on ARCH_MEDIATEK || COMPILE_TEST 403 depends on HAS_IOMEM 404 depends on NVMEM || NVMEM=n 405 depends on RESET_CONTROLLER 406 default y 407 help 408 Enable this option if you want to have support for thermal management 409 controller present in Mediatek SoCs 410 411menu "Broadcom thermal drivers" 412depends on ARCH_BCM || ARCH_BRCMSTB || ARCH_BCM2835 || COMPILE_TEST 413source "drivers/thermal/broadcom/Kconfig" 414endmenu 415 416menu "Texas Instruments thermal drivers" 417depends on ARCH_HAS_BANDGAP || COMPILE_TEST 418depends on HAS_IOMEM 419source "drivers/thermal/ti-soc-thermal/Kconfig" 420endmenu 421 422menu "Samsung thermal drivers" 423depends on ARCH_EXYNOS || COMPILE_TEST 424source "drivers/thermal/samsung/Kconfig" 425endmenu 426 427menu "STMicroelectronics thermal drivers" 428depends on ARCH_STI && OF 429source "drivers/thermal/st/Kconfig" 430endmenu 431 432config TANGO_THERMAL 433 tristate "Tango thermal management" 434 depends on ARCH_TANGO || COMPILE_TEST 435 help 436 Enable the Tango thermal driver, which supports the primitive 437 temperature sensor embedded in Tango chips since the SMP8758. 438 This sensor only generates a 1-bit signal to indicate whether 439 the die temperature exceeds a programmable threshold. 440 441source "drivers/thermal/tegra/Kconfig" 442 443config QCOM_SPMI_TEMP_ALARM 444 tristate "Qualcomm SPMI PMIC Temperature Alarm" 445 depends on OF && SPMI && IIO 446 select REGMAP_SPMI 447 help 448 This enables a thermal sysfs driver for Qualcomm plug-and-play (QPNP) 449 PMIC devices. It shows up in sysfs as a thermal sensor with multiple 450 trip points. The temperature reported by the thermal sensor reflects the 451 real time die temperature if an ADC is present or an estimate of the 452 temperature based upon the over temperature stage value. 453 454config GENERIC_ADC_THERMAL 455 tristate "Generic ADC based thermal sensor" 456 depends on IIO 457 help 458 This enabled a thermal sysfs driver for the temperature sensor 459 which is connected to the General Purpose ADC. The ADC channel 460 is read via IIO framework and the channel information is provided 461 to this driver. This driver reports the temperature by reading ADC 462 channel and converts it to temperature based on lookup table. 463 464menu "Qualcomm thermal drivers" 465depends on (ARCH_QCOM && OF) || COMPILE_TEST 466source "drivers/thermal/qcom/Kconfig" 467endmenu 468 469config ZX2967_THERMAL 470 tristate "Thermal sensors on zx2967 SoC" 471 depends on ARCH_ZX || COMPILE_TEST 472 help 473 Enable the zx2967 thermal sensors driver, which supports 474 the primitive temperature sensor embedded in zx2967 SoCs. 475 This sensor generates the real time die temperature. 476 477config UNIPHIER_THERMAL 478 tristate "Socionext UniPhier thermal driver" 479 depends on ARCH_UNIPHIER || COMPILE_TEST 480 depends on THERMAL_OF && MFD_SYSCON 481 help 482 Enable this to plug in UniPhier on-chip PVT thermal driver into the 483 thermal framework. The driver supports CPU thermal zone temperature 484 reporting and a couple of trip points. 485endif 486