1 // SPDX-License-Identifier: GPL-2.0+ 2 /* 3 * FB driver for the ILI9325 LCD Controller 4 * 5 * Copyright (C) 2013 Noralf Tronnes 6 * 7 * Based on ili9325.c by Jeroen Domburg 8 */ 9 10 #include <linux/module.h> 11 #include <linux/kernel.h> 12 #include <linux/init.h> 13 #include <linux/gpio.h> 14 #include <linux/delay.h> 15 16 #include "fbtft.h" 17 18 #define DRVNAME "fb_ili9325" 19 #define WIDTH 240 20 #define HEIGHT 320 21 #define BPP 16 22 #define FPS 20 23 #define DEFAULT_GAMMA "0F 00 7 2 0 0 6 5 4 1\n" \ 24 "04 16 2 7 6 3 2 1 7 7" 25 26 static unsigned int bt = 6; /* VGL=Vci*4 , VGH=Vci*4 */ 27 module_param(bt, uint, 0000); 28 MODULE_PARM_DESC(bt, "Sets the factor used in the step-up circuits"); 29 30 static unsigned int vc = 0x03; /* Vci1=Vci*0.80 */ 31 module_param(vc, uint, 0000); 32 MODULE_PARM_DESC(vc, "Sets the ratio factor of Vci to generate the reference voltages Vci1"); 33 34 static unsigned int vrh = 0x0d; /* VREG1OUT=Vci*1.85 */ 35 module_param(vrh, uint, 0000); 36 MODULE_PARM_DESC(vrh, "Set the amplifying rate (1.6 ~ 1.9) of Vci applied to output the VREG1OUT"); 37 38 static unsigned int vdv = 0x12; /* VCOMH amplitude=VREG1OUT*0.98 */ 39 module_param(vdv, uint, 0000); 40 MODULE_PARM_DESC(vdv, "Select the factor of VREG1OUT to set the amplitude of Vcom"); 41 42 static unsigned int vcm = 0x0a; /* VCOMH=VREG1OUT*0.735 */ 43 module_param(vcm, uint, 0000); 44 MODULE_PARM_DESC(vcm, "Set the internal VcomH voltage"); 45 46 /* 47 * Verify that this configuration is within the Voltage limits 48 * 49 * Display module configuration: Vcc = IOVcc = Vci = 3.3V 50 * 51 * Voltages 52 * ---------- 53 * Vci = 3.3 54 * Vci1 = Vci * 0.80 = 2.64 55 * DDVDH = Vci1 * 2 = 5.28 56 * VCL = -Vci1 = -2.64 57 * VREG1OUT = Vci * 1.85 = 4.88 58 * VCOMH = VREG1OUT * 0.735 = 3.59 59 * VCOM amplitude = VREG1OUT * 0.98 = 4.79 60 * VGH = Vci * 4 = 13.2 61 * VGL = -Vci * 4 = -13.2 62 * 63 * Limits 64 * -------- 65 * Power supplies 66 * 1.65 < IOVcc < 3.30 => 1.65 < 3.3 < 3.30 67 * 2.40 < Vcc < 3.30 => 2.40 < 3.3 < 3.30 68 * 2.50 < Vci < 3.30 => 2.50 < 3.3 < 3.30 69 * 70 * Source/VCOM power supply voltage 71 * 4.50 < DDVDH < 6.0 => 4.50 < 5.28 < 6.0 72 * -3.0 < VCL < -2.0 => -3.0 < -2.64 < -2.0 73 * VCI - VCL < 6.0 => 5.94 < 6.0 74 * 75 * Gate driver output voltage 76 * 10 < VGH < 20 => 10 < 13.2 < 20 77 * -15 < VGL < -5 => -15 < -13.2 < -5 78 * VGH - VGL < 32 => 26.4 < 32 79 * 80 * VCOM driver output voltage 81 * VCOMH - VCOML < 6.0 => 4.79 < 6.0 82 */ 83 84 static int init_display(struct fbtft_par *par) 85 { 86 par->fbtftops.reset(par); 87 88 if (par->gpio.cs != -1) 89 gpio_set_value(par->gpio.cs, 0); /* Activate chip */ 90 91 bt &= 0x07; 92 vc &= 0x07; 93 vrh &= 0x0f; 94 vdv &= 0x1f; 95 vcm &= 0x3f; 96 97 /* Initialization sequence from ILI9325 Application Notes */ 98 99 /* ----------- Start Initial Sequence ----------- */ 100 write_reg(par, 0x00E3, 0x3008); /* Set internal timing */ 101 write_reg(par, 0x00E7, 0x0012); /* Set internal timing */ 102 write_reg(par, 0x00EF, 0x1231); /* Set internal timing */ 103 write_reg(par, 0x0001, 0x0100); /* set SS and SM bit */ 104 write_reg(par, 0x0002, 0x0700); /* set 1 line inversion */ 105 write_reg(par, 0x0004, 0x0000); /* Resize register */ 106 write_reg(par, 0x0008, 0x0207); /* set the back porch and front porch */ 107 write_reg(par, 0x0009, 0x0000); /* set non-display area refresh cycle */ 108 write_reg(par, 0x000A, 0x0000); /* FMARK function */ 109 write_reg(par, 0x000C, 0x0000); /* RGB interface setting */ 110 write_reg(par, 0x000D, 0x0000); /* Frame marker Position */ 111 write_reg(par, 0x000F, 0x0000); /* RGB interface polarity */ 112 113 /* ----------- Power On sequence ----------- */ 114 write_reg(par, 0x0010, 0x0000); /* SAP, BT[3:0], AP, DSTB, SLP, STB */ 115 write_reg(par, 0x0011, 0x0007); /* DC1[2:0], DC0[2:0], VC[2:0] */ 116 write_reg(par, 0x0012, 0x0000); /* VREG1OUT voltage */ 117 write_reg(par, 0x0013, 0x0000); /* VDV[4:0] for VCOM amplitude */ 118 mdelay(200); /* Dis-charge capacitor power voltage */ 119 write_reg(par, 0x0010, /* SAP, BT[3:0], AP, DSTB, SLP, STB */ 120 BIT(12) | (bt << 8) | BIT(7) | BIT(4)); 121 write_reg(par, 0x0011, 0x220 | vc); /* DC1[2:0], DC0[2:0], VC[2:0] */ 122 mdelay(50); /* Delay 50ms */ 123 write_reg(par, 0x0012, vrh); /* Internal reference voltage= Vci; */ 124 mdelay(50); /* Delay 50ms */ 125 write_reg(par, 0x0013, vdv << 8); /* Set VDV[4:0] for VCOM amplitude */ 126 write_reg(par, 0x0029, vcm); /* Set VCM[5:0] for VCOMH */ 127 write_reg(par, 0x002B, 0x000C); /* Set Frame Rate */ 128 mdelay(50); /* Delay 50ms */ 129 write_reg(par, 0x0020, 0x0000); /* GRAM horizontal Address */ 130 write_reg(par, 0x0021, 0x0000); /* GRAM Vertical Address */ 131 132 /*------------------ Set GRAM area --------------- */ 133 write_reg(par, 0x0050, 0x0000); /* Horizontal GRAM Start Address */ 134 write_reg(par, 0x0051, 0x00EF); /* Horizontal GRAM End Address */ 135 write_reg(par, 0x0052, 0x0000); /* Vertical GRAM Start Address */ 136 write_reg(par, 0x0053, 0x013F); /* Vertical GRAM Start Address */ 137 write_reg(par, 0x0060, 0xA700); /* Gate Scan Line */ 138 write_reg(par, 0x0061, 0x0001); /* NDL,VLE, REV */ 139 write_reg(par, 0x006A, 0x0000); /* set scrolling line */ 140 141 /*-------------- Partial Display Control --------- */ 142 write_reg(par, 0x0080, 0x0000); 143 write_reg(par, 0x0081, 0x0000); 144 write_reg(par, 0x0082, 0x0000); 145 write_reg(par, 0x0083, 0x0000); 146 write_reg(par, 0x0084, 0x0000); 147 write_reg(par, 0x0085, 0x0000); 148 149 /*-------------- Panel Control ------------------- */ 150 write_reg(par, 0x0090, 0x0010); 151 write_reg(par, 0x0092, 0x0600); 152 write_reg(par, 0x0007, 0x0133); /* 262K color and display ON */ 153 154 return 0; 155 } 156 157 static void set_addr_win(struct fbtft_par *par, int xs, int ys, int xe, int ye) 158 { 159 switch (par->info->var.rotate) { 160 /* R20h = Horizontal GRAM Start Address */ 161 /* R21h = Vertical GRAM Start Address */ 162 case 0: 163 write_reg(par, 0x0020, xs); 164 write_reg(par, 0x0021, ys); 165 break; 166 case 180: 167 write_reg(par, 0x0020, WIDTH - 1 - xs); 168 write_reg(par, 0x0021, HEIGHT - 1 - ys); 169 break; 170 case 270: 171 write_reg(par, 0x0020, WIDTH - 1 - ys); 172 write_reg(par, 0x0021, xs); 173 break; 174 case 90: 175 write_reg(par, 0x0020, ys); 176 write_reg(par, 0x0021, HEIGHT - 1 - xs); 177 break; 178 } 179 write_reg(par, 0x0022); /* Write Data to GRAM */ 180 } 181 182 static int set_var(struct fbtft_par *par) 183 { 184 switch (par->info->var.rotate) { 185 /* AM: GRAM update direction */ 186 case 0: 187 write_reg(par, 0x03, 0x0030 | (par->bgr << 12)); 188 break; 189 case 180: 190 write_reg(par, 0x03, 0x0000 | (par->bgr << 12)); 191 break; 192 case 270: 193 write_reg(par, 0x03, 0x0028 | (par->bgr << 12)); 194 break; 195 case 90: 196 write_reg(par, 0x03, 0x0018 | (par->bgr << 12)); 197 break; 198 } 199 200 return 0; 201 } 202 203 /* 204 * Gamma string format: 205 * VRP0 VRP1 RP0 RP1 KP0 KP1 KP2 KP3 KP4 KP5 206 * VRN0 VRN1 RN0 RN1 KN0 KN1 KN2 KN3 KN4 KN5 207 */ 208 #define CURVE(num, idx) curves[num * par->gamma.num_values + idx] 209 static int set_gamma(struct fbtft_par *par, u32 *curves) 210 { 211 unsigned long mask[] = { 212 0x1f, 0x1f, 0x07, 0x07, 0x07, 0x07, 0x07, 0x07, 0x07, 0x07, 213 0x1f, 0x1f, 0x07, 0x07, 0x07, 0x07, 0x07, 0x07, 0x07, 0x07, 214 }; 215 int i, j; 216 217 /* apply mask */ 218 for (i = 0; i < 2; i++) 219 for (j = 0; j < 10; j++) 220 CURVE(i, j) &= mask[i * par->gamma.num_values + j]; 221 222 write_reg(par, 0x0030, CURVE(0, 5) << 8 | CURVE(0, 4)); 223 write_reg(par, 0x0031, CURVE(0, 7) << 8 | CURVE(0, 6)); 224 write_reg(par, 0x0032, CURVE(0, 9) << 8 | CURVE(0, 8)); 225 write_reg(par, 0x0035, CURVE(0, 3) << 8 | CURVE(0, 2)); 226 write_reg(par, 0x0036, CURVE(0, 1) << 8 | CURVE(0, 0)); 227 228 write_reg(par, 0x0037, CURVE(1, 5) << 8 | CURVE(1, 4)); 229 write_reg(par, 0x0038, CURVE(1, 7) << 8 | CURVE(1, 6)); 230 write_reg(par, 0x0039, CURVE(1, 9) << 8 | CURVE(1, 8)); 231 write_reg(par, 0x003C, CURVE(1, 3) << 8 | CURVE(1, 2)); 232 write_reg(par, 0x003D, CURVE(1, 1) << 8 | CURVE(1, 0)); 233 234 return 0; 235 } 236 237 #undef CURVE 238 239 static struct fbtft_display display = { 240 .regwidth = 16, 241 .width = WIDTH, 242 .height = HEIGHT, 243 .bpp = BPP, 244 .fps = FPS, 245 .gamma_num = 2, 246 .gamma_len = 10, 247 .gamma = DEFAULT_GAMMA, 248 .fbtftops = { 249 .init_display = init_display, 250 .set_addr_win = set_addr_win, 251 .set_var = set_var, 252 .set_gamma = set_gamma, 253 }, 254 }; 255 256 FBTFT_REGISTER_DRIVER(DRVNAME, "ilitek,ili9325", &display); 257 258 MODULE_ALIAS("spi:" DRVNAME); 259 MODULE_ALIAS("platform:" DRVNAME); 260 MODULE_ALIAS("spi:ili9325"); 261 MODULE_ALIAS("platform:ili9325"); 262 263 MODULE_DESCRIPTION("FB driver for the ILI9325 LCD Controller"); 264 MODULE_AUTHOR("Noralf Tronnes"); 265 MODULE_LICENSE("GPL"); 266